Brother MFC-J220
Рейтинг
Модули
CARTRIDGE CASE
PAPER TRAY
PCB
SCANNER UNIT
ENGINE
HEAD
PANEL
COVER
Детали COVER
| Деталь: | INK REFILL ASSY (SP), DCP-J125/ MFC-J220/ MFC-J265W/ MFC-J415W FOR US/ CAN/ BRA, DCP-J715W/ M FC-J270W/ M FC-J410W/ MFC-J615W/ MFC-J630W FOR ALL COUNTRIES |
| Парткод: | LK3553001 |
| Деталь: | INK REFILL ASSY (SP), DCP-J125/ MFC-J220/ MFC-J265W/ MFC-J415W EXCEPT FOR US/ CAN/ BRA, DCP-J315W/ DCP-J515W/ MFC-J410 FOR ALL COUNTRIES |
| Парткод: | LK4680001 |
| Деталь: | HEAD JOINT RUBBER (SP) |
| Парткод: | LK3555001 |
| Деталь: | INK CARTRIDGE DETECTION SENSOR PCB |
| Парткод: | LK3329001 |
| Деталь: | PAPER TRAY ASSY (SP), DCP-J125/ DCP-J315W/ MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J415W |
| Парткод: | LS6841004 |
| Деталь: | PAPER TRAY ASSY (SP), DCP-J515W/ DCP-J715W/ M FC-J615W/ M FC-J630W |
| Парткод: | LS6840001 |
| Деталь: | PAPER TRAY ASSY (SP), MFC-J410/ MFC-J410W |
| Парткод: | LS6841005 |
| Деталь: | OUTPUT PAPER TRAY COVER (SP), DCP-J125/ DCP-J315W/ MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J415W |
| Парткод: | LS6839004 |
| Деталь: | OUTPUT PAPER TRAY COVER (SP), DCP-J515W/ DCP-J715W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS6837001 |
| Деталь: | OUTPUT PAPER TRAY COVER (SP), MFC-J410/ MFC-J410W |
| Парткод: | LS6839005 |
| Деталь: | BASE PAD |
| Парткод: | LP1575001 |
| Деталь: | BANK ASSY |
| Парткод: | LS4269001 |
| Деталь: | MAIN PCB, DCP-J125 |
| Парткод: | LT1067001 |
| Деталь: | MAIN PCB, DCP-J315W |
| Парткод: | LT1068011 |
| Деталь: | MAIN PCB, DCP-J515W |
| Парткод: | LT1066001 |
| Деталь: | MAIN PCB, DCP-J715W |
| Парткод: | LT1053011 |
| Деталь: | MAIN PCB, MFC-J220 |
| Парткод: | LT1069021 |
| Деталь: | MAIN PCB, MFC-J265W/ MFC-J270W |
| Парткод: | LT1070031 |
| Деталь: | MAIN PCB, MFC-J410 |
| Парткод: | LT1071041 |
| Деталь: | MAIN PCB, MFC-J410W/ MFC-J415W |
| Парткод: | LT1072051 |
| Деталь: | MAIN PCB, MFC-J615W/ MFC-J630W EXCEPT FOR CHN |
| Парткод: | LT1052001 |
| Деталь: | MAIN PCB, MFC-J265W FOR CHN |
| Парткод: | LT1070035 |
| Деталь: | MAIN PCB, MFC-J615W FOR CHN |
| Парткод: | LT1052005 |
| Деталь: | POWER SUPPLY PCB FOR US/ CAN |
| Парткод: | LT1075001 |
| Деталь: | POWER SUPPLY PCB EXCEPT FOR US/ CAN/ CHN/ TWN/ ZAF/ ASA/ BRA/ RUS |
| Парткод: | LT0485001 |
| Деталь: | POWER SUPPLY PCB FOR CHN |
| Парткод: | LT0586001 |
| Деталь: | POWER SUPPLY PCB FOR TWN |
| Парткод: | LT1654001 |
| Деталь: | POWER SUPPLY PCB FOR ZAF/ ASA/ RUS |
| Парткод: | LT0660001 |
| Деталь: | POWER SUPPLY PCB FOR BRA |
| Парткод: | LT1516001 |
| Деталь: | MJ PCB, MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W FOR US/ CAN/ CH N/ TWN/ HK/ A RG/ CHL/ ASA/ OCE |
| Парткод: | LT1022001 |
| Деталь: | MJ PCB, MFC-J220/ MFC-J265W/ MFC-J410/ MFC-J415W/ MFC-J615W FOR GER/ UK/ FRA/ BEL/ NLD/ CHE/ AUS/ SPA/ ITA/ ISR/ POR/ TUR/ POL/ RUS/ PND |
| Парткод: | LT1022004 |
| Деталь: | MJ PCB, MFC-J220 FOR ZAF |
| Парткод: | LT1022024 |
| Деталь: | MJ PCB, MFC-J220/ MFC-J410 FOR KOR |
| Парткод: | LT1022044 |
| Деталь: | ADF & SCANNER COVER ASSY (SP), DCP-J715W |
| Парткод: | LX7722001 |
| Деталь: | ADF & SCANNER COVER ASSY (SP), MFC-J410/ MFC-J410W |
| Парткод: | LX7722002 |
| Деталь: | ADF & SCANNER COVER ASSY (SP), MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LX7726001 |
| Деталь: | SCANNER COVER ASSY (SP), DCP-J125/ MFC-J220 |
| Парткод: | LX6578002 |
| Деталь: | SCANNER COVER ASSY (SP), DCP-J315W/ DCP-J515W/ MFC-J265W/ MFC-J270W |
| Парткод: | LX6578001 |
| Деталь: | DOCUMENT COVER ASSY (SP), DCP-J125 FOR US/ BRA, MFC-J220 FOR ALL COUNTRIES |
| Парткод: | LX6583001 |
| Деталь: | DOCUMENT COVER ASSY (SP), DCP-J125 EXCEPT FOR US/ BRA, DCP-J315W/ DCP-J515W/ MFC-J265W/ MFC-J270W FOR ALL COUNTRIES |
| Парткод: | LX6584001 |
| Деталь: | HINGE, DCP-J125/ DCP-J315W/ DCP-J515W/ MFC-J220/ MFC-J265W/ MFC-J270W |
| Парткод: | LS4537007 |
| Деталь: | EMBLEM BROTHER, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LX7155001 |
| Деталь: | ADF & DOCUMENT COVER ASSY (SP), DCP-J715W |
| Парткод: | LX6434001 |
| Деталь: | ADF & DOCUMENT COVER ASSY (SP), MFC-J410/ MFC-J410W |
| Парткод: | LX6434002 |
| Деталь: | ADF & DOCUMENT COVER ASSY (SP), M FC-J415W/ M FC-J615W/ M FC-J630W |
| Парткод: | LX6436001 |
| Деталь: | HINGE, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS4442007 |
| Деталь: | PAPER JAM INST. LABEL, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS5965001 |
| Деталь: | PAPER JAM INST. LABEL, DCP-J125/ DCP-J315W/ DCP-J515W/ MFC-J220/ MFC-J265W/ MFC-J270W |
| Парткод: | LS5965001 |
| Деталь: | DOCUMENT SPONGE ASSY (SP), DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS6891001 |
| Деталь: | DOCUMENT SENSOR PCB ASSY, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415WMFC-J615W/ MFC-J630W |
| Парткод: | LG6753001 |
| Деталь: | DOCUMENT ROLLER HOLDER ASSY, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS4406001 |
| Деталь: | TAPTITE CUP B M3X8, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | 87310816 |
| Деталь: | ADF MOTOR, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS4414001 |
| Деталь: | SCREW PAN (S/ P WASHER) M3X6, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | 0A5300606 |
| Деталь: | ADF UNIT, DCP-J715W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LX3609001 |
| Деталь: | ADF UNIT, MFC-J410/ MFC-J410W |
| Парткод: | LX3609002 |
| Деталь: | ADF COVER, DCP-J715W/ MFC-J410/ MFC-J410W |
| Парткод: | LX3610001 |
| Деталь: | ADF COVER, M FC-J415W/ MFC-J615W/ M FC-J630W |
| Парткод: | LX3639001 |
| Деталь: | DOCUMENT COVER SUPPORT, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS5961001 |
| Деталь: | DOCUMENT STOPPER, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LX1864007 |
| Деталь: | SEPARATION PAD AND FILM, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS5437001 |
| Деталь: | EXIT FILM, DCP-J715W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LP1429001 |
| Деталь: | ENGINE UNIT (SP), DCP-J125/ DCP-J315W/ MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W |
| Парткод: | LS6537001 |
| Деталь: | ENGINE UNIT (SP), DCP-J515W |
| Парткод: | LX1874001 |
| Деталь: | ENGINE UNIT (SP), DCP-J715W/ M FC-J615W/ M FC-J630W |
| Парткод: | LX1876001 |
| Деталь: | JAM CLEAR COVER |
| Парткод: | LS4253003 |
| Деталь: | HEAD COVER |
| Парткод: | LS4383001 |
| Деталь: | TUBE SUPPORT PLATE |
| Парткод: | LX0376001 |
| Деталь: | TUBE SUPPORT WIRE |
| Парткод: | LS4469001 |
| Деталь: | CARRIAGE PCB ASSY (SP) |
| Парткод: | LS6543001 |
| Деталь: | MAINTENANCE UNIT (SP) |
| Парткод: | LS6544001 |
| Деталь: | EARTH SPRING |
| Парткод: | LS5775001 |
| Деталь: | TAPTITE CUP B M3X10 |
| Парткод: | 87311016 |
| Деталь: | STAR WHEEL HOLDER |
| Парткод: | LS4301001 |
| Деталь: | PLATEN F ASSY, DCP-J125/ DCP-J315W/ DCP-J515W/ MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W |
| Парткод: | LS4303001 |
| Деталь: | PLATEN M ASSY, DCP-J715W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS4304001 |
| Деталь: | CARRIAGE MOTOR |
| Парткод: | LX3629001 |
| Деталь: | RF ENCODER DISK |
| Парткод: | LP1471001 |
| Деталь: | INNER CHUTE ASSY |
| Парткод: | LS4249001 |
| Деталь: | SENSOR HARNESS UNIT |
| Парткод: | LT0466001 |
| Деталь: | TIMING BELT |
| Парткод: | LS4198001 |
| Деталь: | ASF GEAR SHAFT OUTER |
| Парткод: | LS4260001 |
| Деталь: | ASF ROLLER 9 UNIT ASSY |
| Парткод: | LX0126001 |
| Деталь: | ASF MOTOR |
| Парткод: | LS4091001 |
| Деталь: | SWITCHING LEVER GUIDE |
| Парткод: | LS4098001 |
| Деталь: | SCREW PAN (S/ P WASHER) M3X5 |
| Парткод: | LS4375001 |
| Деталь: | ENCODER STRIP |
| Парткод: | LS4467001 |
| Деталь: | SCREW BIND M3X6 |
| Парткод: | 300606 |
| Деталь: | SCREW BIND M2X12 |
| Парткод: | 21206 |
| Деталь: | PE ACTUATOR 9 ASSY |
| Парткод: | LS4120001 |
| Деталь: | PE ACTUATOR SPRING |
| Парткод: | LS4075001 |
| Деталь: | REGISTRATION SENSOR ACTUATOR |
| Парткод: | LS4251001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J125 FOR US |
| Парткод: | LX3668001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR US |
| Парткод: | LX3108001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR US/ CAN |
| Парткод: | LX3681001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J270W FOR US |
| Парткод: | LX6411001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J410W FOR US |
| Парткод: | LX6975001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J415W FOR US/ CAN |
| Парткод: | LX3685001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR US/ CAN |
| Парткод: | LX1980001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J630W FOR US |
| Парткод: | LX6425001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J125 FOR GER |
| Парткод: | LX6266001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J315W FOR GER |
| Парткод: | LX3302001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J515W FOR GER |
| Парткод: | LX6311001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J715W FOR GER |
| Парткод: | LX3997001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR GER/ AUS |
| Парткод: | LX6369001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR GER/ AUS |
| Парткод: | LX6393001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J410 FOR GER/ AUS |
| Парткод: | LX6215001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J415W FOR GER/ AUS |
| Парткод: | LX6292001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR GER/ AUS |
| Парткод: | LX6324001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J125 FOR UK/ ISR/ ZAF/ ASA/ OCE/ PND |
| Парткод: | LX3122001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J315W FOR UK/ ASA/ OCE/ PND |
| Парткод: | LX3719001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J515W FOR UK/ OCE/ PND |
| Парткод: | LX3716001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J715W FOR UK/ ASA/ OCE/ PND |
| Парткод: | LX3130001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR UK/ ISR |
| Парткод: | LX3705001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J410 FOR UK/ BEL/ CHE/ ISR |
| Парткод: | LX3709001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J415W FOR UK/ CHE |
| Парткод: | LX3710001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR UK/ BEL/ CHE/ ISR |
| Парткод: | LX3628001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J125 FOR FRA/ CHE/ IBR/ CEE |
| Парткод: | LX6268001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J315W FOR FRA/ CHE/ IBR/ CEE |
| Парткод: | LX6232001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J515W FOR FRA/ CHE/ IBR/ CEE |
| Парткод: | LX6312001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J715W FOR FRA/ CHE/ IBR/ CEE |
| Парткод: | LX6094001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR FRA |
| Парткод: | LX6370001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR FRA |
| Парткод: | LX6394001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J415W FOR FRA |
| Парткод: | LX6293001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR FRA |
| Парткод: | LX6325001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR NLD |
| Парткод: | LX6662001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR NLD |
| Парткод: | LX6505001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J415W FOR NLD |
| Парткод: | LX6488001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR NLD |
| Парткод: | LX6455001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR CHE/ ISR/ ZAF |
| Парткод: | LX3702001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR SPA |
| Парткод: | LX6371001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR SPA |
| Парткод: | LX6395001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J410 FOR SPA |
| Парткод: | LX6223001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J415W FOR SPA |
| Парткод: | LX6295001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR SPA |
| Парткод: | LX6326001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J125 FOR ITA |
| Парткод: | LX6267001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J315W FOR ITA |
| Парткод: | LX1310001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J515W FOR ITA |
| Парткод: | LX6319001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J715W FOR ITA |
| Парткод: | LX6089001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR ITA |
| Парткод: | LX6372001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR ITA |
| Парткод: | LX6396001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J410 FOR ITA |
| Парткод: | LX6227001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR ITA |
| Парткод: | LX6327001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR POR |
| Парткод: | LX6663001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR POR |
| Парткод: | LX6506001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J410 FOR POR |
| Парткод: | LX6605001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J415W FOR POR |
| Парткод: | LX6490001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR POR |
| Парткод: | LX6463001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR CHN |
| Парткод: | LX7690001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR CHN |
| Парткод: | LX7617001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J410 FOR TWN/ HK |
| Парткод: | LX7166001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J415W FOR TWN |
| Парткод: | LX7867001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J315W FOR TUR |
| Парткод: | LX6981001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR TUR |
| Парткод: | LX7237001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J125 FOR HK |
| Парткод: | LX7167001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J315W FOR HK |
| Парткод: | LX7171001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR HK |
| Парткод: | LX7163001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR HK |
| Парткод: | LX7002001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J125 FOR ARG/ CHL |
| Парткод: | LX6970001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J410 FOR ARG/ CHL |
| Парткод: | LX6938001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR ARG/ CHL |
| Парткод: | LX6538001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR POL |
| Парткод: | LX7245001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR POL |
| Парткод: | LX6990001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J415W FOR POL |
| Парткод: | LX6983001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR POL |
| Парткод: | LX6866001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR ASA/ OCE |
| Парткод: | LX6962001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR ASA/ OCE |
| Парткод: | LX6598001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J415W FOR ASA/ OCE |
| Парткод: | LX6548001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR ASA/ OCE |
| Парткод: | LX6523001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J125 FOR BRA |
| Парткод: | LX7178001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J220 FOR KOR |
| Парткод: | LX7942001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J410 FOR KOR |
| Парткод: | LX7948001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J315W FOR RUS |
| Парткод: | LX6926001 |
| Деталь: | CONTROL PANEL ASSY, DCP-J515W FOR RUS |
| Парткод: | LX6992001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J265W FOR RUS |
| Парткод: | LX6995001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J410 FOR OCE |
| Парткод: | LX6899001 |
| Деталь: | CONTROL PANEL ASST, MFC-J410 FOR PND |
| Парткод: | LX6603001 |
| Деталь: | CONTROL PANEL ASSY, MFC-J615W FOR PND |
| Парткод: | LX6466001 |
| Деталь: | CONTROL PANEL BASE, DCP-J125 |
| Парткод: | LX3123001 |
| Деталь: | CONTROL PANEL BASE, DCP-J315W |
| Парткод: | LX3720001 |
| Деталь: | CONTROL PANEL BASE, DCP-J515W/ DCP-J715W |
| Парткод: | LX3131007 |
| Деталь: | CONTROL PANEL BASE, MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J415W |
| Парткод: | LX3109007 |
| Деталь: | CONTROL PANEL BASE, MFC-J410/ MFC-J410W |
| Парткод: | LX3109011 |
| Деталь: | CONTROL PANEL BASE, MFC-J615W/ MFC-J630W |
| Парткод: | LX1981007 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR ASA/ OCE |
| Парткод: | LX6524001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J410 FOR KOR |
| Парткод: | LX7943001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J265W FOR RUS |
| Парткод: | LX6996001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J410 FOR PND |
| Парткод: | LX6604001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR PND |
| Парткод: | LX6467001 |
| Деталь: | PRINTED PANEL PLATE, DCP-J515W |
| Парткод: | LX3715001 |
| Деталь: | PRINTED PANEL PLATE, DCP-J715W |
| Парткод: | LX3134001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J410W/ MFC-J415W FOR US/ CAN |
| Парткод: | LX3114001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W/ MFC-J630W FOR US/ CAN |
| Парткод: | LX1987001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J265W/ MFC-J410/ MFC-J415W FOR GER/ AUS |
| Парткод: | LX6216001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR GER/ AUS |
| Парткод: | LX6328001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J265W/ MFC-J410/ MFC-J415W FOR UK/ BEL/ CHE/ ISR/ ZAF |
| Парткод: | LX3703001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR UK/ BEL/ CHE/ ISR |
| Парткод: | LX3627001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J265W/ MFC-J415W FOR FRA |
| Парткод: | LX6294001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR FRA |
| Парткод: | LX6329001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J265W/ MFC-J415W FOR NLD |
| Парткод: | LX6489001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR NLD |
| Парткод: | LX6456001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J265W/ MFC-J410/ MFC-J415W FOR SPA |
| Парткод: | LX6224001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR SPA |
| Парткод: | LX6330001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J265W/ MFC-J410 FOR ITA |
| Парткод: | LX6228001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR ITA |
| Парткод: | LX6331001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J265W/ MFC-J410/ MFC-J415W FOR POR |
| Парткод: | LX6491001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR POR |
| Парткод: | LX6464001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J265W FOR CHN |
| Парткод: | LX7692001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR CHN |
| Парткод: | LX7614001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J410/ MFC-J415W FOR TWN/ HK |
| Парткод: | LX7164001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220 FOR TUR |
| Парткод: | LX7239001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR HK |
| Парткод: | LX7003001 |
| Деталь: | PRINTED PANEL PALTE, MFC-J410 FOR ARG/ CHL |
| Парткод: | LX6939001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR ARG/ CHL |
| Парткод: | LX6539001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J265W/ MFC-J415W FOR POL |
| Парткод: | LX6984001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J615W FOR POL |
| Парткод: | LX6867001 |
| Деталь: | PRINTED PANEL PLATE, MFC-J220/ MFC-J265W/ MFC-J410/ MFC-J415W FOR ASA/ OCE |
| Парткод: | LX6549001 |
| Деталь: | RUBBER KEYPAD L, MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W |
| Парткод: | LX3110001 |
| Деталь: | RUBBER KEYPAD L, MFC-J615W/ MFC-J630W |
| Парткод: | LX1989001 |
| Деталь: | RUBBER KEYPAD, DCP-J125/ DCP-J315W/ DCP-J515W/ DCP-J715W EXCEPT FOR TUR/ HK |
| Парткод: | LX3125001 |
| Деталь: | RUBBER KEYPAD R, MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W EXCEPT FOR TWN/ TUR/ HK |
| Парткод: | LX3112001 |
| Деталь: | RUBBER KEYPAD R,MFC-J615W/ MFC-J630W EXCEPT FOT HK |
| Парткод: | LX1991001 |
| Деталь: | RUBBER KEYPAD R, MFC-J220/ MFC-J410/ MFC-J415W FOR TWN/ HK |
| Парткод: | LX7230001 |
| Деталь: | RUBBER KEYPAD, DCP-J315W FOR TUR |
| Парткод: | LX7232001 |
| Деталь: | RUBBER KEYPAD R, MFC-J220 FOR TUR |
| Парткод: | LX7238001 |
| Деталь: | RUBBER KEYPAD, DCP-J125/ DCP-J315W FOR HK |
| Парткод: | LX7231001 |
| Деталь: | RUBBER KEYPAD R, MFC-J615W FOR HK |
| Парткод: | LX7229001 |
| Деталь: | CONTROL PANEL PCB ASSY, DCP-J125/ DCP-J315W |
| Парткод: | LT0994001 |
| Деталь: | CONTROL PANEL PCB ASSY, DCP-J515W/ DCP-J715W |
| Парткод: | LT0990002 |
| Деталь: | CONTROL PANEL PCB ASSY, MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W |
| Парткод: | LT0992001 |
| Деталь: | CONTROL PANEL PCB ASSY,MFC-J615W/ MFC-J630W |
| Парткод: | LT1086001 |
| Деталь: | PRINTED LCD SHEET, DCP-J125 |
| Парткод: | LX3129001 |
| Деталь: | PRINTED LCD SHEET, DCP-J315W |
| Парткод: | LX3958001 |
| Деталь: | PRINTED LCD SHEET, MFC-J220 |
| Парткод: | LX3116001 |
| Деталь: | PRINTED LCD SHEET, MFC-J265W EXCEPT FOR CHN |
| Парткод: | LX3682001 |
| Деталь: | PRINTED LDC SHEET, MFC-J270W |
| Парткод: | LX6412001 |
| Деталь: | PRINTED LCD SHEET, MFC-J410 |
| Парткод: | LX3684001 |
| Деталь: | PRINTED LCD SHEET, MFC-J410W |
| Парткод: | LX6976001 |
| Деталь: | PRINTED LCD SHEET, MFC-J415W |
| Парткод: | LX3686001 |
| Деталь: | PRINTED LCD SHEET, MFC-J265W FOR CHN |
| Парткод: | LX7691001 |
| Деталь: | COLOR LCD, DCP-J125/ DCP-J315W/ MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W |
| Парткод: | A63045001 |
| Деталь: | EX PANEL ASSY, DCP-J125 FOR US |
| Парткод: | LX3669001 |
| Деталь: | EX PANEL ASSY, DCP-J125/ DCP-J315W FOR GER/ CHE (GERMAN) |
| Парткод: | LX6440001 |
| Деталь: | EX PANEL ASSY, DCP-J515W/ DCP-J715W FOR GER/ CHE (GERMAN) |
| Парткод: | LX6415001 |
| Деталь: | EX PANEL ASSY, DCP-J125/ DCP-J315W FOR UK/ ISR/ ZAF/ ASA/ OCE/ PND/ CEE (ENGLISH) |
| Парткод: | LX6932001 |
| Деталь: | EX PANEL ASSY, DCP-J515W/ DCP-J715W FOR UK/ ASA/ OCE/ PND/ CEE (ENGLISH) |
| Парткод: | LX6472001 |
| Деталь: | EX PANEL ASSY, DCP-J125/ DCP-J315W FOR FRA/ CHE (FRENCH) |
| Парткод: | LX6233001 |
| Деталь: | EX PANEL ASSY, DCP-J515W/ DCP-J715W FOR FRA/ CHE (FRENCH) |
| Парткод: | LX6095001 |
| Деталь: | EX PANEL ASSY, DCP-J125/ DCP-J315W FOR FRA (DUTCH) |
| Парткод: | LX6235001 |
| Деталь: | EX PANEL ASSY, DCP-J515W/ DCP-J715W FOR FRA (DUTCH) |
| Парткод: | LX6098001 |
| Деталь: | EX PANEL ASSY, DCP-J125/ DCP-J315W FOR ITA |
| Парткод: | LX6231001 |
| Деталь: | EX PANEL ASSY, DCP-J515W/ DCP-J715W FOR ITA |
| Парткод: | LX6090001 |
| Деталь: | EX PANEL ASSY, DCP-J315W FOR TUR |
| Парткод: | LX6980001 |
| Деталь: | EX PANEL ASSY, DCP-J125/ DCP-J315W FOR HK |
| Парткод: | LX7168001 |
| Деталь: | EX PANEL ASSY, DCP-J125/ DCP-J315W FOR ARG/ CHL/ IBR (SPANISH) |
| Парткод: | LX6237001 |
| Деталь: | EX PANEL ASSY, DCP-J125/ DCP-J315W FOR BRA/ IBR (PORTUGUESE) |
| Парткод: | LX6239001 |
| Деталь: | EX PANEL ASSY, DCP-J315W FOR RUS |
| Парткод: | LX6927001 |
| Деталь: | EX PANEL ASSY, DCP-J515W FOR RUS |
| Парткод: | LX6994001 |
| Деталь: | EX PANEL ASSY, DCP-J515W/ DCP-J715W FOR IBR (SPANISH) |
| Парткод: | LX6099001 |
| Деталь: | EX PANEL ASSY, DCP-J515W/ DCP-J715W FOR IBR (PORTUGUESE) |
| Парткод: | LX6100001 |
| Деталь: | EX PANEL ASSY, DCP-J125/ DCP-J315W FOR CEE (POLISH) |
| Парткод: | LX6933001 |
| Деталь: | EX PANEL ASSY, DCP-J515W/ DCP-J715W FOR CEE (POLISH) |
| Парткод: | LX6474001 |
| Деталь: | COLOR LCD UNIT, DCP-J515W/ DCP-J715W |
| Парткод: | LX3132001 |
| Деталь: | COLOR LCD UNIT, MFC-J615W EXCEPT FOR CHN |
| Парткод: | LX1982001 |
| Деталь: | COLOR LCD UNIT, MFC-J615W FOR CHN |
| Парткод: | LX7616001 |
| Деталь: | COLOR LCD UNIT, MFC-J630W |
| Парткод: | LX6426001 |
| Деталь: | LATCH SPRING FOR DCP-J515W/ DCP-J715W/ M FC-J615W/ M FC-J630W |
| Парткод: | LX3978001 |
| Деталь: | LOWER COVER |
| Парткод: | LS5134001 |
| Деталь: | INK ABSORBER FELT (INK ABSORBER BOX LOWER) |
| Парткод: | LS4699001 |
| Деталь: | INK ABSORBER FELT (MAINTENANCE UNIT) |
| Парткод: | LS5136001 |
| Деталь: | INK ABSORBER TUBE ASSY (SP) |
| Парткод: | LS6842001 |
| Деталь: | FLUSHING BOX |
| Парткод: | LS5141001 |
| Деталь: | SPEAKER SPRING, MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS5334001 |
| Деталь: | SPEAKER, MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LT0520001 |
| Деталь: | UPPER COVER (SP), DCP-J125 |
| Парткод: | LS6852003 |
| Деталь: | UPPER COVER (SP), DCP-J315W/ DCP-J515W |
| Парткод: | LS6852002 |
| Деталь: | UPPER COVER (SP), DCP-J715W |
| Парткод: | LS6853001 |
| Деталь: | UPPER COVER (SP), MFC-J220 |
| Парткод: | LX6973002 |
| Деталь: | UPPER COCER (SP), M FC-J265W/ M FC-J270W/ M FC-J410/ M FC-J410W/ MFC-J415W |
| Парткод: | LX6973001 |
| Деталь: | UPPER COVER (SP), MFC-J615W/ MFC-J630W |
| Парткод: | LS6845001 |
| Деталь: | INK CARTRIDGE COVER, DCP-J125/ DCP-J315W/ DCP-J515W/ DCP-J715W/ MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LX1976007 |
| Деталь: | INK CARTRIDGE COVER, MFC-J410/ MFC-J410W |
| Парткод: | LX1976011 |
| Деталь: | FRONT COVER, DCP-J125/ DCP-J315W/ DCP-J515W/ DCP-J715W/ MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LX1977007 |
| Деталь: | FRONT COVER, MFC-J410/ MFC-J410W |
| Парткод: | LX1977011 |
| Деталь: | HARNESS COVER, DCP-J125/ MFC-J220 |
| Парткод: | LS5154011 |
| Деталь: | HARNESS COVER, DCP-J315W/ DCP-J515W/ DCP-J715W/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS5154007 |
| Деталь: | CIS FLAT CABLE COVER, DCP-J125/ MFC-J220 |
| Парткод: | LS5155011 |
| Деталь: | CIS FLAT CABLE COVER, DCP-J315W/ DCP-J515W/ DCP-J715W/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LS5155007 |
| Деталь: | SCANNER COVER SUPPORT |
| Парткод: | LS5156002 |
| Деталь: | SCANNER COVER DAMPER |
| Парткод: | LS5159001 |
| Деталь: | ENCODER GUARD FILM |
| Парткод: | LS6316001 |
| Деталь: | ENCODER GUARD SPRING |
| Парткод: | LS6317001 |
| Деталь: | EXT CAP, MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J410/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W FOR US/ CAN/ NLD/ CHE/ SPA/ ISR/ POR/ CHN/ TWN/ HK/ ARG/ CHL/ POL/ ASA/ KOR/ OCE/ PND |
| Парткод: | LE8842001 |
| Деталь: | MJ COVER EXT, MFC-J220/ MFC-J265W/ MFC-J410/ / MFC-J415W/ MFC-J615W FOR GER/ UK/ FRA/ BEL/ AUS/ ITA |
| Парткод: | UF5745000 |
| Деталь: | ENCODER CAUTION LABEL |
| Парткод: | LS5964001 |
| Деталь: | TAPTITE BIND B M4X12 |
| Парткод: | 85411216 |
| Деталь: | TAPTITE CUP B M3X10 |
| Парткод: | 87311016 |
| Деталь: | INNOBELLA LABEL FOR US |
| Парткод: | LX3721001 |
| Деталь: | INNOBELLA LABEL EXCEPT FOR US |
| Парткод: | LX3722001 |
| Деталь: | WLAN PCB, DCP-J315W/ DCP-J515W/ DCP-J715W/ MFC-J265W/ MFC-J270W/ MFC-J410W/ MFC-J415W/ MFC-J615W/ MFC-J630W |
| Парткод: | LT1401001 |
| Деталь: | INK ABSORBER FELT (INK ABSORBER BOX UPPER) |
| Парткод: | LX6286001 |
| Деталь: | MEDIA MODULE COVER, DCP-J125/ DCP-J315W/ DCP-J515W/ MFC-J220/ MFC-J265W/ MFC-J270W/ MFC-J415W EXCEPT FOR CHN |
| Парткод: | LX3104001 |
| Деталь: | MEDIA MODULE COVER, DCP-J715W/ MFC-J615W/ MFC-J630W EXCEPT FOR CHN |
| Парткод: | LX1978001 |
| Деталь: | MEDIA MODULE COVER, MFC-J410/ MFC-J410W |
| Парткод: | LX3104002 |
| Деталь: | MEDIA MODULE COVER, MFC-J265W FOR CHN |
| Парткод: | LX7899001 |
| Деталь: | MEDIA MODULE COVER, MFC-J615W FOR CHN |
| Парткод: | LX3718001 |
Коды ошибок
20, 21, 22, 23
26, 27, 28, 29
2A, 2B, 2C, 2D
2F
3E
3x
40
42
43
44
46
48
49
4F
50, 51
52
57
5A, 5B
5D
5E
60, 62
6C
6F
70, 71
72
73
7A
7D
7E
80
81
82
83
84
88
8A
8B
8C
8D
8F
90
91
A1
A2
A3
A5
A6
A7
A8
AF
BD
DF, E0
E2
E3
E4
E5
E6
E7
EA
EC
ED
EE
F7
F8
Описание
| Error code: | 20, 21, 22, 23 |
| Description: | Cannot identify the ink cartridge loaded because the signal values detected by the corresponding ink empty sensor and ink cartridge detection sensor are different from the specified values. |
| Remedy: | Ink cartridge not loaded correctly - Ink cartridge loaded after the ink cartridge cover has been left open for 10 minutes or more - Ink cartridge replaced when the power is OFF - Ink cartridge loaded very quickly - Ink cartridge halfway taken in and out Reload the corresponding ink cartridge. Ink cartridge partially broken Replace the ink cartridge. The ink cartridge loaded is not the specified one Load the specified ink cartridge. Ink empty sensor defective Replace the ink refill ASSY. Ink empty sensor PCB defective Main PCB defective Replace the main PCB. |
| Error code: | 26, 27, 28, 29 |
| Description: | Running out of ink. |
| Remedy: | Running out of ink 26: Black ink 27: Yellow ink 28: Cyan ink 29: Magenta ink Replace or reload the ink cartridge. Ink empty sensor PCB defective Replace the ink refill ASSY. Main PCB defective Replace the main PCB. |
| Error code: | 2A, 2B, 2C, 2D |
| Description: | Cannot detect ink cartridges. |
| Remedy: | Ink cartridge not loaded 2A: Black ink 2B: Yellow ink 2C: Cyan ink 2D: Magenta ink Replace or reload the ink cartridge. Ink cartridge broken Replace the ink cartridge. Ink cartridge detection sensor defective Replace the ink refill ASSY. Ink cartridge detection sensor PCB defective Main PCB defective Replace the main PCB. |
| Error code: | 2F |
| Display: | Close Ink Cover |
| Description: | The Ink cartridge cover sensor detected an opened cover. |
| Remedy: | <User Check> - Close the Ink cartridge cover. 1 Ink cartridge cover sensor harness connection failure Reconnect the Ink cartridge cover sensor harness. 2 Damaged Ink cartridge cover Replace the Ink cartridge cover. 3 Ink cartridge cover sensor defective Replace the Ink cartridge cover sensor ASSY. 4 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 3E |
| Display: | Unable to print 3E |
| Description: | EEPROM bus error (Not applicable) |
| Causes: | Main PCB failure |
| Remedy: | Replace the main PCB ASSY. |
| Error code: | 3x |
| Description: | Head/carriage unit travel error. |
| Remedy: | Software malfunction Open and close the scanner cover. Unplug and plug the AC cord. Any obstacles on the travel path of the head/carriage unit Clean and lubricate the CR guide rail and CR support chassis. CR timing belt come off Set the CR timing belt into place. CR encoder strip stained or scratched Replace the CR encoder strip. Carriage PCB defective Replace the carriage PCB ASSY. Head/carriage unit broken Replace the head/carriage unit. Carriage motor defective Replace the carriage motor. Main PCB defective Replace the main PCB. Power supply PCB defective Replace the power supply PCB. Maintenance unit defective Replace the maintenance unit. |
| Error code: | 40 |
| Display: | Scanner locked |
| Description: | 10-348 ERROR 40 FUSER MAIN LAMP FAILURE Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault, Clear <10-348 & 10-350> is run. |
| Causes: | 1. Deformed paper sensor actuator or faulty sensor. 2. SMPS PBA or Main PBA is defective 3. Faulty cables or connectors. |
| Remedy: | Switch printer power OFF. Remove the Fuser Assembly. Warning Fuser may be very hot. Use extreme caution to prevent burns. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Replace the Engine Control Board. |
| Error code: | 42 |
| Display: | Self Diagnostic Temperature |
| Description: | 10-352 ERROR 42 FUSER STS (FRONT) WARM TIME FAILURE |
| Causes: | 1. The ‘Open Cover’ microswitch may be stuck or faulty 2. The tab on the front cover may be damaged or broken 3. Check the connector and cables between Switch and main PBA. |
| Remedy: | Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board. |
| Error code: | 43 |
| Display: | Send Error (AUTH) |
| Description: | 10-353 ERROR 43 FUSER SSR1 ON TIME FAILURE |
| Causes: | 1. The ‘Open Cover’ microswitch may be stuck or faulty 2. Check the connector and cables between Switch and main PBA. |
| Remedy: | Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board. |
| Error code: | 44 |
| Display: | Send Error (DNS) |
| Description: | Fuser Sub Lamp Overheat Failure, Code 44 The front thermistor has detected an overheat condition. Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault is performed. |
| Causes: | • Fuser • Engine Control Board |
| Remedy: | 1 1. Turn OFF power, remove the fuser assembly and allow it to cool down. 2. Measure the resistance between the Fuser connector P600-7 and P600-9. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 2. Replace the fuser assembly. 2 1. Reinstall the fuser assembly. 2. Enter service diagnostics. 3. From the Sensor Tests run the Fuser Temperature test. 4. Is the temperature indicated approximately 165o C? Go to step 4. Go to step 3. 3 1. Turn OFF printer power. 2. Measure the resistance between J641-4 and J641-5 on the engine control board. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 4. Repair or replace the wiring harness. 4 1. Turn printer power back ON. 2. Is there ~+3.4 VDC between J590-3 and ground? Check the AC wiring harness to the fuser. If the check is OK, replace the AC drive assembly. Replace the engine control board. |
| Error code: | 46 |
| Display: | Send Error (SMTP) |
| Description: | 10-354 ERROR 46 FUSER STS (REAR) WARM TIME FAILURE |
| Causes: | 1. Check stability of 24V supply to LSU. |
| Remedy: | Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-7 and P600-9. Does the resistance measure between 20 ohms and 100 ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-3 and P404A-4 on the Engine Control Board. Does the resistance measure between 20K ohms and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board. |
| Error code: | 48 |
| Display: | [Stop Pressed] |
| Description: | Fan Failure, Code 48 The machine logic detected a failure of the Fuser fan, LVPS fan, or rear fan. |
| Causes: | • Fuser Fan • LVPS Fan • Rear Fan |
| Remedy: | 1 1. Enter service diagnostics and run the fan test. 2. Does the fuser fan rotate at a high speed? Go to step 4. Go to step 2. 2 1. Check for voltage at J222-4. 2. Does the voltage measure +24 VDC? Go to step 3. Check the wiring to the fuser fan, if the wiring is OK, replace the engine control board. 3 Does the front panel indicate the fans are ON? Replace the fan. Check the wiring to the fuser fan, if the wiring is OK, replace the engine control board. 4 Does the rear fan revolve at high speed? Go to step 7. Go to step 5. 5 1. Check for voltage at J552-1. 2. Does the voltage measure +24 VDC? Go to step 6. Check the wiring to the rear fan, if the wiring is OK replace the interface board. If the problem continues, replace the engine control board. 6 Does the front panel indicate the fans are ON? Replace the rear fan. Check the wiring tot he rear fan, if the wiring is OK, replace the engine control board. 7 Does the LVPS fan revolve at high speed? The fans are operating correctly. If the problem persists, replace the engine control board. Go to step 8. 8 1. Check for voltage at J214-4. 2. Is +24 VDC present? Go to step 9. Check the wiring to the LVPS fan, if the wiring is OK, replace the engine control board. 9 Does the front panel indicate the fans are ON? Replace the LVPS assembly. Check the wiring to the LVPS fan, if the wiring is OK, replace the engine control board. |
| Error code: | 49 |
| Display: | Tray 1 Paper Empty |
| Description: | There is no paper in the tray 1. |
| Causes: | Pressure roller thermistor, pressure roller lamp connector, MCU |
| Remedy: | Load paper in the tray 1. |
| Error code: | 4F |
| Display: | Unable to print 4F |
| Description: | Head voltage drops quickly. |
| Remedy: | <User Check> - This may occur when the surrounding temperature is low. Increase the surrounding temperature before use. - Unplug the power cord from the outlet. Plug it again after several seconds and check if the problem has been resolved. 1 Head flat cable connection failure Reconnect the Head flat cable. 2 Carriage flat cable connection failure Reconnect the Carriage flat cable. 3 Carriage PCB defective Replace the Carriage PCB ASSY. 4 Head defective Replace the Head/carriage unit. 5 Power supply PCB defective Replace the Power supply PCB ASSY. 6 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 50, 51 |
| Description: | The purge cam switch does not come ON or OFF even after the purge cam has been driven by the specified number of pulses. |
| Remedy: | Planetary arm assembly not engaged correctly Set the maintenance unit into place. If the planetary arm does not move smoothly, clean it. Purge cam switch harness not connected correctly Correct the connection. Purge cam switch broken Replace the maintenance unit. Gear(s) on the maintenance unit broken Paper feed motor defective Replace the paper feed motor. Power supply PCB defective Replace the power supply PCB. Main PCB defective Replace the main PCB. |
| Error code: | 52 |
| Display: | Send Error (POP3) |
| Description: | Fan Failure One of the two fans has failed resulting in a fatal error. |
| Causes: | • Rear Fan, PL1.1.19 • Fuser Fan, PL5.3.31 |
| Remedy: | 1 Check the fans for damage or debris: • Fuser Fan, PL1.1.19 • Rear Fan, PL5.3.31 Is either fan damaged? Replace the defective fan. Go to Step 3. 2 Replace the defective fan. Does the error persist? Go to Step 3 Complete 3 Test the fans. Run the Service Diagnostics fan tests to isolate the defective fan. Did one of the fans fail? Go to the troubleshooting procedure for the specific fan. If both fans pass, replace the Engine Control Board. |
| Error code: | 57 |
| Display: | Toner Low |
| Description: | The toner cartridge is almost empty. |
| Remedy: | Take out the toner cartridge and thoroughly shake it. By doing this, you can temporarily reestablish printing operations. |
| Error code: | 5A, 5B |
| Description: | Abnormal stop of purge cam being driven |
| Remedy: | Foreign materials in the machine Remove foreign materials. PF encoder disk being in contact with the upper cover and deformed Replace the PF encoder disk. PF encoder PCB defective Replace the PF encoder PCB. Main drain tube bent Replace the ink absorber box. Clutch gear broken Replace the maintenance unit. Purge cam gear broken Abnormal load applied to the purge cam Planetary arm assembly broken Paper feed motor defective Replace the engine unit. PF roller gear L broken Engine unit defective Main PCB defective Replace the main PCB. Power supply PCB defective Replace the power supply PCB. |
| Error code: | 5D |
| Display: | Unable to print 5D |
| Description: | Overcurrent protection was activated in the driver IC during Purge cam operation. |
| Causes: | The driving current has exceeded the limit due to an abnormal load applied to the maintenance unit. |
| Remedy: | 1 Foreign materials in the Maintenance unit part Remove foreign materials. 2 Maintenance unit defective Replace the Maintenance unit. 3 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 5E |
| Display: | Unable to print 5E |
| Description: | Overcurrent protection was activated in the driver IC during Maintenance unit pump operation. |
| Causes: | The driving current has exceeded the limit due to an abnormal load applied to the maintenance unit. |
| Remedy: | 1 Foreign materials in the Maintenance unit part Remove foreign materials. 2 Maintenance unit defective Replace the Maintenance unit. 3 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 60, 62 |
| Description: | Paper width sensor (media sensor) error. |
| Remedy: | Paper width sensor (media sensor) adjustment failure Readjust the left and right margins. Paper width sensor defective Replace the carriage PCB ASSY. Head flat cables broken Main PCB defective Replace the main PCB. |
| Error code: | 6C |
| Display: | Unable to Print 6C |
| Description: | Fuser unit failure (The center thermistor detects higher temperature than the specified value.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6F |
| Display: | Unable to Print 6F |
| Description: | Fuser unit failure (The center and side thermistors detect extremely high temperature.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 70, 71 |
| Description: | Cannot detect the ON/ OFF state of cap lift cam switch |
| Remedy: | Cap lift cam switch defective Replace the maintenance unit. ASF encoder sensor defective Replace the ASF motor ASSY. ASF motor defective Main PCB defective Replace the main PCB. |
| Error code: | 72 |
| Display: | Paper Jam 1 |
| Description: | Engine Firmware Failure The Engine Control Board detected a firmware error. |
| Causes: | • Engine Control Board, Pl9.1.16 • EEPROM Board, PL9.1.12 |
| Remedy: | 1 Cycle printer power. Does the error persist? Go to Step 2. Complete 2 Is P/J144 on the EEPROM Board properly seated and defect free? Go to Step 3. Reseat P/J144 or replace the EEPROM Board. 3 Turn printer power off and then back on. Does the error persist? Replace the Engine Control Board. Complete |
| Error code: | 73 |
| Display: | Paper Jam 2 |
| Description: | Paper Jam 2 |
| Causes: | The front part of paper is jammed just after passing through the discharge sensor. |
| Error code: | 7A |
| Display: | Unable to clean 7A |
| Description: | No detection of the main motor lock signal. |
| Causes: | Main motor failure. Main PCB failure. |
| Remedy: | 1 Main motor failure Replace the main motor ASSY. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 7D |
| Display: | Unable to clean 7D |
| Description: | Dirt on drum unit |
| Causes: | Dirt or dust on drum unit electrodes. HVPS PCB failure. Main PCB failure. |
| Remedy: | 1 Dirt or dust on drum unit electrodes Clean the electrodes on the drum unit. ( p.271 "Electrodes location on the drum unit") 2 HVPS PCB failure Replace the HVPS PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 7E |
| Display: | Unable to print 7E |
| Description: | Head property information not input. |
| Remedy: | 1 Head property information not input Input the head property information. 2 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 80 |
| Display: | ERROR 80 FORMAT |
| Description: | Engine Logic Board Failure, Code 80 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete Replace the engine control board or the image processor board. |
| Error code: | 81 |
| Display: | 81 |
| Description: | Controller to Engine Communications Failure, Code 81 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Turn the printer off. 3. Remove the Image processor board, IP board cover and metal cover. 4. Inspect the orange ribbon cable between the relay board and the engine control board. 5. Is the connector fully seated and free from damage? Replace in the following order: • Image processor board • Electrical chassis assembly • Engine control board |
| Error code: | 82 |
| Display: | h`******** |
| Description: | Engine Logic Board RAM/ROM Failure, Code 82 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace the engine control board. |
| Error code: | 83 |
| Display: | h`******** |
| Description: | Engine Logic Board NVRAM Failure, Code 83 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace in the following order: • engine control board • image processor board |
| Error code: | 84 |
| Display: | h`******** |
| Description: | Controller to Engine Logic Board Time Failure, Code 84 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace the engine control board. |
| Error code: | 88 |
| Display: | Paper Jam |
| Description: | Lower Tray Communication Failure, Code 88 |
| Causes: | • Engine Control Interface Board • Tray module board • Engine Control board |
| Remedy: | 1 Is J668-1 on the tray module board +5 VDC? Go to step 2. Use the wirenets to troubleshoot and repair the open wire. 2 Is J668-3 on the tray module board +24 VDC? Go to step 3. Use the wirenets to troubleshoot and repair the open wire. 3 1. Check the following connectors for continuity: • P669-1 to J534A-15 • P669-2 to J534A-14 • P669-3 to J534A-13 • P669-4 to J534A-12 • P669-5 to J534A-11 • P669-6 to J534A-10 2. Do all checks indicate continuity? Replace in the following order: • engine control interface board • tray module board • engine control board Check and repair broken wires or bad connectors. |
| Error code: | 8A |
| Display: | Paper Jam |
| Description: | Paper jam in Tray 1 (T1) (It is detects by the registration front sensor) |
| Causes: | Harness connection failure of registration front sensor PCB ASSY. Paper feed roller worn out. Registration front sensor PCB failure. Main PCB failure. |
| Remedy: | 1 Harness connection failure of registration front sensor PCB ASSY Check the harness connection of the registration front sensor PCB ASSY in the appropriate tray, and reconnect it. 2 Paper feed roller worn out Replace the paper feed roller. 3 Registration front sensor PCB failure Check the sensor performance following the procedure ( p.183 "Operational Check of Sensors (Function code 32)"). If any problem occurs, replace the registration front sensor PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 8B |
| Display: | Unable to Print 8B |
| Description: | Paper jam in Tray 2 |
| Causes: | Dirt on edge sensor. Harness connection failure of high voltage power supply PCB ASSY. Paper feeding kit worn out (MP/ Tray 1/ Tray 2). Registration front sensor failure. Main PCB failure |
| Remedy: | Clean the edge sensor. Check the harness connection of the high voltage power supply PCB ASSY in the appropriate tray, and reconnect it. Replace the paper feeding kit of the appropriate tray. Procedure described in "4.10 Sensor Operational Check (Function code 32)" in Chapter 6. If any problem occurs, replace the high voltage power supply PCB ASSY. Replace the main PCB ASSY. |
| Error code: | 8C |
| Display: | Paper Jam |
| Description: | Paper jam in MP Tray |
| Causes: | Dirt on edge sensor. Harness connection failure of high voltage power supply PCB ASSY. Paper feeding kit worn out (MP/ Tray 1/ Tray 2). Registration front sensor failure. Main PCB failure |
| Remedy: | Clean the edge sensor. Check the harness connection of the high voltage power supply PCB ASSY in the appropriate tray, and reconnect it. Replace the paper feeding kit of the appropriate tray. Procedure described in "4.10 Sensor Operational Check (Function code 32)" in Chapter 6. If any problem occurs, replace the high voltage power supply PCB ASSY. Replace the main PCB ASSY. |
| Error code: | 8D |
| Description: | Paper jam near paper eject tray (When power on, it is detects by the eject sensor.) |
| Causes: | Paper eject actuator not operating smoothly catching in some position. Eject sensor PCB ASSY failure. Main PCB failure. |
| Remedy: | 1 Paper eject actuator not operating smoothly catching in some position. Re-assemble the paper eject actuator. Ensure the paper eject sensor operates smoothly. 2 Eject sensor PCB ASSY failure Replace the eject sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 8F |
| Display: | Unable to print 8F |
| Description: | Paper feed motor does not stop. The PF encoder sensor cannot detect the rotation of the Paper feed motor. |
| Remedy: | <User Check> - Release the release lever at the back of the Paper tray and remove the jammed recording paper in Jam clear cover part, Platen part and front part. 1 Foreign materials in the recording paper feeding path Remove foreign materials. 2 Paper feed motor harness connection failure Reconnect the Paper feed motor harness. 3 PF encoder sensor harness connection defective Reconnect the PF encoder sensor harness. 4 PF encoder disk defective Replace the PF encoder disk. 5 PF encoder sensor defective Replace the PF encoder sensor PCB ASSY. 6 Paper feed motor defective Replace the Paper feed motor. 7 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 90 |
| Display: | ERROR 90 F / W |
| Description: | Sub CPU fault. |
| Remedy: | Replace the CPU circuit board with a new one. |
| Error code: | 91 |
| Display: | 91 |
| Description: | Total counter |
| Remedy: | Wrong size paper loaded in the paper tray. Load the correct size of paper. Registration sensor defective Replace the registration sensor PCB. Main PCB defective Replace the main PCB. |
| Error code: | A1 |
| Display: | Cover is Open |
| Description: | Jam at Door A |
| Causes: | • Tray 1 (MPT) Feed Roller, PL10.1.53 • Tray 1 (MPT) Pick Roller, PL10.1.43 • Tray 1 (MPT) Retard Roller, PL10.1.16 • Registration Clutch #1, PL8.1.85 • Tray 2 Registration Motor, PL4.2.36 • Tray 2 Feed Motor, PL4.2.35 • Front Sensor Board, PL4.2.97 |
| Remedy: | 1 Check the following for evidence of fault, dirt, debris, or damage: • Tray 1 (MPT) Feed Rollers • Registration Rollers • Sensor Actuator Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Registration #1 Sensor. Run the Service Diagnostics Registration Entrance Sensor test. Does the sensor operate correctly? Go to Step 3. Replace the actuator. If the error persists, replace the Front Sensor Board. 3 Test the Feed Motor, Registration Motor, and Registration Clutch #1. Do the components function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the harness for each motor and clutch. Are the wiring harnesses properly connected and free from defects? Replace the Engine Control Board. Replace the wiring harness and/or the problem motor/ clutch. |
| Error code: | A2 |
| Display: | DOCUMENT JAM |
| Description: | Jam at Door A |
| Causes: | • Duplex Unit, PL16.1.0 |
| Remedy: | 1 Check the following for evidence of fault, dirt, debris, or damage: • Door A • Door D • Duplex Unit Rollers • Duplex Unit connector • Duplex Sensors and Actuators Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Duplex Unit sensors. Run the Service Diagnostics for each of the four Duplex Unit sensors. Do the sensors and actuators function correctly Go to Step 3. Replace the damaged sensor. 3 Test the Duplex Unit motors. Run the Service Diagnostics Duplex Motor tests. Do the motors function correctly Go to Step 4. Replace the Duplex Unit 4 Inspect the wiring harness for the Duplex Unit. Is the wiring harness properly connected and free from defects? Replace the Duplex Unit. Replace the Engine Control Board. |
| Error code: | A3 |
| Display: | DOCUMENT JAM |
| Description: | Jam at Door A Misfeed at Tray 1 (MPT) Media reached the Duplex Reverse Sensor, but a second sheet was detected entering the feed path from Tray 1 (MPT). This error represents a misfeed jam for media fed from Tray 1 (MPT). |
| Causes: | • Tray 1 (MPT) Feed Roller, PL10.1.53 • Tray 1 (MPT) Pick Roller, PL10.1.43 • Tray 2 Registration Motor, PL4.2.36 • Tray 2 Feed Motor, PL4.2.35 • Front Sensor Board, PL4.2.97 |
| Remedy: | 1 Check the following for evidence of fault, dirt, debris, or damage: • Tray 1 (MPT) Feed Rollers • Registration Rollers • Sensor Actuator Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Registration #1 Sensor. Run the Service Diagnostics Registration Entrance Sensor test. Does the sensor operate correctly? Go to Step 3. Replace the actuator. If the error persists, replace the Front Sensor Board. 3 Test the Feed Motor, Registration Motor, and Registration Clutch #1. Do the components function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check each motor and clutch harness. Are the harnesses properly connected and free from defects? Replace the Engine Control Board. Replace the harness and/or problem motor/ clutch. |
| Error code: | A5 |
| Display: | Unable to Scan A5 |
| Description: | ADF interlock |
| Causes: | Scanning failure. |
| Remedy: | 1 Scanning failure Turn the power switch off and on. Then, try scanning again. |
| Error code: | A6 |
| Display: | A6-Bypass Feeder Jam |
| Description: | Paper did not exit the Multi-sheet Bypass Feeder properly, causing a paper jam. Open Cover A and refer to the labels on the printer to clear the jam. |
| Causes: | FB unit failure. Main PCB failure. |
| Remedy: | 1. Ensure the correct weight and type of paper is loaded in the feeder. Also ensure the paper is loaded correctly in the feeder. 2. Clean the bypass feeder’s pick roller. 3. Test the main feed motor as described in “Motor and clutch tests”. Replace the main feed motor. 5. Replace the engine controller board. |
| Error code: | A7 |
| Display: | A7-Duplex Entry Jam |
| Description: | Paper did not enter the duplex module properly, causing a paper jam. Open Cover A and refer to the labels on the printer to clear the jam. |
| Causes: | Power supply fan error |
| Remedy: | 1. Ensure the correct weight and type of paper is loaded in the currently used tray. Also ensure the paper is loaded correctly in the tray. 2. Clean the duplex unit’s rollers. 3. Test the duplex motor and clutch as described in “Motor and clutch tests”. Replace the duplex unit. 5. Replace the engine controller board. |
| Error code: | A8 |
| Display: | Unable to Scan A8 |
| Description: | ADF exit interlock |
| Causes: | Ozone fan error |
| Remedy: | Replace the CCD module. Replace the main PCB ASSY. |
| Error code: | AF |
| Display: | Unable to Scan AF |
| Description: | FB unit home position failure |
| Causes: | FB unit failure. Main PCB failure. |
| Remedy: | 1 FB unit failure Replace the FB unit. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | BD |
| Display: | Unable to Scan BD |
| Description: | Engine EEPROM check error. Printing is continued. |
| Causes: | Engine EEPROM check error |
| Remedy: | Replace the CCD module. Replace the main PCB ASSY. |
| Error code: | DF, E0 |
| Description: | Modem error |
| Remedy: | SDAA chip defective Turn the machine off and then on. Main PCB defective Replace the main PCB. |
| Error code: | E2 |
| Display: | SVC E2 ERROR |
| Description: | Reset signal happened. Might read E-2 something else. |
| Error code: | E3 |
| Display: | SVC E3 ERROR |
| Description: | Jam in transfer area |
| Causes: | • If the light path of the Clamp senors both C and L are not opened within 10 seconds after after the Clamp motor is activated. [During Master Release from the Clamp Plate] • If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated. • If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated. [When the Clamp Plate opens during Master Clamping] • If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated. • If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated. [When the Clamp Plate closes during Master Clamping] • If the light path of the Clamp sensor L is not opened within 10 seconds after the Clamp motor is activated. |
| Remedy: | Paper exit detector (POUT) signal recognition error 1) Paper exit detector (POUT) trouble 2) Paper exit detector (POUT) signal input circuit trouble REMEDY (Check) 1) Paper exit detector (POUT) 2) MCU PWB paper exit detector (POUT) signal input circuit (Remedy) 1) Paper exit detector (POUT) replacement 2) MCU PWB replacement (After work) 1) When the MCU PWB is replaced, perform simulations to input various set values and adjustment values. |
| Error code: | E4 |
| Display: | E4-2:EXITJAM |
| Description: | Exit jam |
| Causes: | • If the Overflow sensor detects excessive ink in the Squeegee unit. |
| Remedy: | Remove excess ink from the Drum. |
| Error code: | E5 |
| Display: | SVC E5 ERROR |
| Description: | Front door open |
| Causes: | • Connector error between CON1 board and the drum liaison board • Defective connector between the drum liaison board and the drum board • Defective transistors and logic gate ICs in the eraser controller circuit on the engine board • Connection error between drum unit board and eraser lamp • Broken eraser lamp |
| Error code: | E6 |
| Display: | SVC E6 ERROR |
| Description: | Right side interlock |
| Causes: | • If Position-A sensor cannot be detected (or keeps detecting) even though the Main motor encoder sensor signal is making the output after the Main motor is activated. |
| Remedy: | Confirm details of the error using the error code and correct the error. Then ask the remote party to transmit again. |
| Error code: | E7 |
| Display: | SVC E7 ERROR |
| Description: | Duplex interlock |
| Causes: | Both the Open Sensing Switch and the Close Sensing Switch detect “0” while the Pocket Door is moving. |
| Error code: | EA |
| Display: | Document Jam |
| Description: | Thermal fuse |
| Causes: | The light intensity of the Exposure Lamp is more than the specified amount. |
| Remedy: | EXP Lamp (FL1) Turn off the machine. Is the EXP Lamp (FL1) connected with the EXP Lamp Socket properly? Are the connectors connect properly? No Connect properly. Is the side of the EXP Lamp burnt to black? Yes Replace the EXP Lamp with the new one. EXP Sensor PCB Can you fix the problem when you replace the EXP Sensor PCB with new one? Yes OK. EXP. Power Supply PCB Is the voltage between J24-1-1(+) and J24-1-2 (-) on the EXP. Power Supply PCB 24V during the Ready condition? No Replace the EXP. Power Supply PCB with the new one. |
| Error code: | EC |
| Display: | Unable to print EC |
| Description: | ADF jam |
| Causes: | Harness connection failure of fan motor. Fan motor failure. Main PCB failure. |
| Remedy: | 1 Harness connection failure of fan motor Check the harness connection of the fan motor, and reconnect it. 2 Fan motor failure Replace the fan motor. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | ED |
| Display: | Touchscreen Init. Failed |
| Description: | ADF jam |
| Causes: | . Data readout error on the flash ROM |
| Remedy: | Developer Motor Are the connectors connect with the Developer Motor properly? No Connect properly. Control PCB (PW10620) Enter the Service Mode and select the Manual Charging Test of the Function Checking Mode. (Refer to the page 8-24.) 1. Does the voltage between the CN106-4 (+) and CN106-6 (-) on the Control PCB (PW10620) change to about 6V to 0V when the Developer Motor rotates? 2. Is the voltage between CN211-4 (+) and CN211-1 (-) on the Control PCB (PW10620) about 24V during the Ready condition? No Replace the Control PCB (PW10620) with the new one. Developer Motor Motor Control PCB Replace the Developer Motor or the Motor Control PCB with the new one. |
| Error code: | EE |
| Display: | EE-Transfer Belt Unit Missing |
| Description: | The transfer belt is either missing or requires reseating to be recognized by the printer. Turn off the printer, make sure the transfer belt is properly installed and turn on the printer. |
| Causes: | LD Signal is detected for 1 seconds continuously while the Main Motor is rotating. |
| Remedy: | 1. Remove and re-install the transfer belt unit. 2. Clean the transfer belt unit’s contact on the front-left side of the engine chassis. Clean the corresponding contacts on the transfer belt unit. 3. Install a new transfer belt unit. 4. Replace the engine controller board. 5. Replace the printer unit chassis. |
| Error code: | F7 |
| Display: | F7 |
| Description: | IPT1 program error |
| Causes: | Checksum has failed on option font ROM. |
| Remedy: | Replace the main PCB. |
| Error code: | F8 |
| Display: | Unable to Print F8 |
| Description: | No power to collator |
| Causes: | Battery harness connection failure. Battery exhausted. Main PCB failure. |
| Remedy: | 1 Battery harness connection failure Reconnect the battery harness. 2 Battery exhausted Replace the battery. 3 Main PCB failure Replace the main PCB ASSY. |
