Lexmark MX611

Рейтинг

Модули

Option trays

FRAME

Staple finisher option

Control panel

Imaging

Staple finisher (right)

Staple finisher (rear)

COVERS

Electronics 2

Staple finisher (top)

Electronics 1

Детали

Деталь:	250-sheet tray
Парткод:	40X8287

Деталь:	550-sheet tray
Парткод:	40X8286

Деталь:	Dust cover, 250.sheet tray
Парткод:	40X8520

Деталь:	Dust cover, 550.sheet tray
Парткод:	40X8521

Деталь:	ACM assembly
Парткод:	40X8262

Деталь:	Pick roller assembly
Парткод:	40X8443

Деталь:	Separator roll assembly
Парткод:	40X8444

Деталь:	550-sheet tray insert
Парткод:	40X8086

Деталь:	250-sheet tray insert
Парткод:	40X8305

Деталь:	Staple finisher option
Парткод:	40X8121

Деталь:	LCD top cover
Парткод:	40X9089

Деталь:	7 LCD (touch-screen)
Парткод:	40X7861

Деталь:	Control panel cover (MX610de)
Парткод:	40X9125

Деталь:	Control panel cover (MX611de)
Парткод:	40X9132

Деталь:	Control panel cover (MX611dhe)
Парткод:	40X9133

Деталь:	Keypad assembly cover
Парткод:	40X9120

Деталь:	UICC cable
Парткод:	40X9052

Деталь:	UICC
Парткод:	40X9130

Деталь:	UICC video cable
Парткод:	40X9085

Деталь:	Interface PCBA
Парткод:	40X9115

Деталь:	ADF separator roller
Парткод:	40X9108

Деталь:	ADF input tray
Парткод:	40X9054

Деталь:	ADF ASSEMBLY
Парткод:	40X9093

Деталь:	Restraint pad
Парткод:	40X9110

Деталь:	Flatbed cushion (legal)
Парткод:	40X5804

Деталь:	ADF right hinge
Парткод:	40X7546

Деталь:	Flatbed
Парткод:	40X9094

Деталь:	MPF USB cable
Парткод:	40X9051

Деталь:	USB cable bracket
Парткод:	40X9053

Деталь:	Scanner front cover
Парткод:	40X9097

Деталь:	Cave light lens
Парткод:	40X9088

Деталь:	Speaker cable
Парткод:	40X9080

Деталь:	ADF left hinge
Парткод:	40X9129

Деталь:	MPF wireless cable
Парткод:	40X9050

Деталь:	SPEAKER
Парткод:	40X9079

Деталь:	ADF pick roll
Парткод:	40X8736

Деталь:	ADF top cover (legal)
Парткод:	40X9142

Деталь:	High end ADF cable
Парткод:	40X9117

Деталь:	Stapler interface cable
Парткод:	40X8144

Деталь:	Sensor (stapler access door)
Парткод:	40X7592

Деталь:	Stapler door close limit switch with cable
Парткод:	40X8139

Деталь:	Stapler carriage assembly
Парткод:	40X8142

Деталь:	Stapler right cover
Парткод:	40X8130

Деталь:	Stapler cartridge access door
Парткод:	40X8129

Деталь:	Staple roll holder
Парткод:	40X8149

Деталь:	Stapler cooling fan
Парткод:	40X8148

Деталь:	Stapler power supply unit
Парткод:	40X8135

Деталь:	Stapler rear cover
Парткод:	40X8128

Деталь:	Trapped staple access door
Парткод:	40X8458

Деталь:	Sensor (stapler pass through)
Парткод:	40X8134

Деталь:	Stapler rear door close limit switch with cable
Парткод:	40X8138

Деталь:	Sensor (stapler rear door)
Парткод:	40X7592

Деталь:	Front door sensor
Парткод:	40X8048

Деталь:	Cartridge smart chip contact
Парткод:	40X8266

Деталь:	TONER DENSITY SENSOR
Парткод:	40X8046

Деталь:	Power supply, 100 V/110 V
Парткод:	40X7797

Деталь:	Power supply, 220 V
Парткод:	40X7798

Деталь:	Trailing edge sensor
Парткод:	40X8045

Деталь:	Duplex sensor and input sensor
Парткод:	40X8043

Деталь:	Media present sensor
Парткод:	40X7592

Деталь:	Index sensor
Парткод:	40X8044

Деталь:	Stapler service cover
Парткод:	40X8140

Деталь:	Stapler top cover
Парткод:	40X8141

Деталь:	Stapler controller PCBA
Парткод:	40X8137

Деталь:	Stapler tamper motor
Парткод:	40X8125

Деталь:	Sensor (stapler bin full send)
Парткод:	40X8131

Деталь:	Sensor (stapler bin full receive)
Парткод:	40X8132

Коды ошибок

111.00...111.69

121.07...121.37

126.01, 126.02

132.01...132.34

133.05...133.08

140.10...140.80

146.00

155.00

171.03...171.07

200.01

200.02...200.08

200.09...200.15

200.16

200.19, 200.21

200.23, 200.24, 200.29, 200.30

200.31, 200.32, 200.33

200.38, 200.42, 200.44, 200.45

201.01

202.01...202.28

230.01...232.10

241.01...241.49

242.01...244.49

250.06...250.18

31.21...31.25

31.40...31.45

31.46

31.60...31.65

31.66

32.01, 32.05, 32.10

32.11

321.51, 321.52, 321.53

322.54, 322.55, 322.56.

324.57, 324.58, 324.59.

325.60...325.63

331.51...331.53

332.54, 332.55, 332.56

334.57, 334.58, 334.59

335.60...335.63

341.51, 341.52, 341.53

342.54, 342.55, 342.56

344.57, 344.58, 344.59

35, 36, 37

41.xy, 42

840.01, 840.02, 840.03

841.xx

842.xx

843.00...849.xx

900.xx

912.xx

940.xx

948.xx

950.xx

952.xx

953.xx

954.xx

955.xx

956.xx

957.xx

958.xx

959.xx

960.xx

961.xx

964.xx

975.xx

976.xx

978.xx

979.xx

980.xx

981.xx

982.xx

983.xx

984.xx

990.xx

991.xx

Описание

Парткод

Название

LEXMARK 500Z Блок формирования изображения, возвратный

LEXMARK 500ZA Блок формирования изображения

LEXMARK 600XA Тонер картридж черный (20000 стр.)

LEXMARK 605 Тонер картридж черный (2500 стр.), возвратный

LEXMARK 605H Тонер картридж черный (10000 стр.) Return Program

LEXMARK 605X Тонер картридж черный (20000 стр.), возвратный

LEXMARK Картриджи со скрепками. 5 шт.

LEXMARK Узел термозакрепления в сборе (Печка)

Деталь:	MPF pick roller and Separator pad
Парткод:	40X8295
Цена:	1 500 ₽

Error code:	111.00...111.69
Description:	111.00 Pel clock check failed. 111.01 Downlevel ASIC detected. 111.31 Printhead never delivered HSYNCs. 111.32 Printhead lost HSYNCs. 111.40 Wrong printhead installed 111.50 Open-loop printhead error, open-loop sweep state. 111.51 111.52 Open-loop printhead error, check prelim amp state. 111.53 Open-loop printhead error, enable amp Kp state. 111.54 Closed-loop printhead error, amp Kp failed to converge. 111.55 Closed-loop printhead error while waiting for amp Kp to converge. 111.56 Closed-loop printhead error, amp Ki failed to converge. 111.57 Closed-loop printhead error while waiting for amp Ki to converge. 111.58 Closed-loop printhead error, load scan regs state. 111.59 Closed-loop printhead error, forward and reverse capture times differ by too much. 111.60 Closed-loop printhead sweep error, check sweep accuracy state. 111.61 Printhead drive control out of range due to an external event beyond what the control is designed to handle. 111.62 Closed-loop printhead error, off-resonant PI effort state. 111.63 Timed out on POR sweep. 111.64 Attempted to exceed open loop drive limits. 111.65 111.66 Failed alignment of printhead. 111.67 111.68 Too many fake HSYNCs while aligning printhead. 111.69
Remedy:	Step 1 Check the LSU cables JVIDEO1 and JGLV1 for proper connection. Are they properly connected? Go to step 2. Reseat the cables. Step 2 Inspect the LSU cables and connectors. Are they free of damage? Replace the controller board. See “Controller board removals”. Replace the LSU. See “Laser scanning unit (LSU) removal”.

Error code:	200.01
Display:	200.01
Description:	Input sensor is made when printer tries to print from an idle state. Possible causes: • Paper jam leaving page over sensor • Defective input sensor • Faulty system card
Remedy:	• Check for anything in the paper path that might cause the paper to jam.

Error code:	34
Description:	Non-continuous labels are being treated as continuous labels.
Causes:	The printer was not calibrated for the media being used. The printer is configured for continuous media.
Remedy:	Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81.

Error code:	52
Display:	Send Error (POP3)
Description:	Fan Failure One of the two fans has failed resulting in a fatal error.
Causes:	• Rear Fan, PL1.1.19 • Fuser Fan, PL5.3.31
Remedy:	1 Check the fans for damage or debris: • Fuser Fan, PL1.1.19 • Rear Fan, PL5.3.31 Is either fan damaged? Replace the defective fan. Go to Step 3. 2 Replace the defective fan. Does the error persist? Go to Step 3 Complete 3 Test the fans. Run the Service Diagnostics fan tests to isolate the defective fan. Did one of the fans fail? Go to the troubleshooting procedure for the specific fan. If both fans pass, replace the Engine Control Board.

Error code:	54
Display:	Send Error (Wrong Config)
Description:	10-398 ERROR 54 FAN FAILURE
Causes:	· Loose cable connection · Defective ozone fan · Defective IOD2 board · Defective MCTL board
Remedy:	Enter Service Diagnostics Mode. Run the “Fuser Fan” test. Does the Fuser Fan operate? Y↓N→ Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-1 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-4 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-3 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the Fuser Fan. Replace the Fuser Fan Assembly. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-5 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-8 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-7 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the +24 VDC LVPS Fan. Replace the +24 VDC LVPS Fan.

Error code:	80
Display:	ERROR 80 FORMAT
Description:	Engine Logic Board Failure, Code 80
Remedy:	1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete Replace the engine control board or the image processor board.

Error code:	84
Display:	h`********
Description:	Controller to Engine Logic Board Time Failure, Code 84
Remedy:	1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace the engine control board.

Error code:	88
Display:	Paper Jam
Description:	Lower Tray Communication Failure, Code 88
Causes:	• Engine Control Interface Board • Tray module board • Engine Control board
Remedy:	1 Is J668-1 on the tray module board +5 VDC? Go to step 2. Use the wirenets to troubleshoot and repair the open wire. 2 Is J668-3 on the tray module board +24 VDC? Go to step 3. Use the wirenets to troubleshoot and repair the open wire. 3 1. Check the following connectors for continuity: • P669-1 to J534A-15 • P669-2 to J534A-14 • P669-3 to J534A-13 • P669-4 to J534A-12 • P669-5 to J534A-11 • P669-6 to J534A-10 2. Do all checks indicate continuity? Replace in the following order: • engine control interface board • tray module board • engine control board Check and repair broken wires or bad connectors.

Деталь:	Stapler diverter spring
Парткод:	40X9098

Деталь:	ACM liftplate gearbox
Парткод:	40X8084

Деталь:	TRAY GUIDE
Парткод:	40X9523

Деталь:	Main drive gearbox
Парткод:	40X8085

Lexmark MX611

Модули

Детали

Коды ошибок

Описание

Парткод

Название

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку