Mimaki JV400-160LX
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
пьезоэлектрическая струйная
Макс. формат
A0
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Печать фотографий |
|
Телефон |
|
Копир |
|
Цветность печати |
цветная |
Факс |
|
Сканер |
|
Макс. формат |
A0 |
Технология печати |
пьезоэлектрическая струйная |
Тип |
струйный |
Размещение |
напольный |
Тип устройства |
Принтер |
Принтер |
|
Прямая печать |
|
Система непрерывной подачи чернил |
|
Двусторонняя печать |
|
Пигментные чернила |
|
Печать без полей |
|
Количество цветов |
4 |
Макс, разрешение для ч/б печати |
|
| По Y | 1 200 |
| По X | 1 200 |
Сканер |
|
Слайд-адаптер |
|
Стандарт TWAIN |
|
Стандарт WIA |
|
Отправка изображения по e-mail |
|
Расходные материалы |
|
Количество картриджей |
4 |
Печать на: |
|
| Фотобумаге |
|
| CD/DVD |
|
| Конвертах |
|
| Этикетках |
|
| Карточках |
|
| Матовой бумаге |
|
| Рулоне |
|
| Пленках |
|
| Глянцевой бумаге |
|
Факс |
|
Цветной |
|
PC Fax |
|
Телефон |
|
Проводная трубка |
|
Спикерфон |
|
Стандарт DECT |
|
Автоответчик |
|
Caller ID |
|
АОН |
|
Беспроводная трубка |
|
Языки управления |
|
|
|
|
| PostScript |
|
| PPDS |
|
| PCL 6 |
|
| PCL 5e |
|
| PCL 5c |
|
| PostScript 3 |
|
| PostScript 2 |
|
Финишер |
|
Сортер |
|
Брошюровщик |
|
Электронная сортировка |
|
Сортировка со сдвигом |
|
Степлер |
|
Интерфейсы |
|
Ethernet (RJ-45) |
|
FireWire (IEEE 1394) |
|
Wi-Fi |
|
Wi-Fi 802.11n |
|
Bluetooth |
|
LPT |
|
AirPrint |
|
Инфракрасный порт |
|
RS-232 |
|
Веб-интерфейс |
|
Устройство для чтения карт памяти |
|
USB |
|
Версия USB |
2,0 |
Дополнительная информация |
|
Работа от аккумулятора |
|
Поддержка ОС |
|
| Linux |
|
| Mac OS |
|
| DOS |
|
| Windows |
|
Потребляемая мощность |
|
| При работе | 1 800 |
Габариты |
|
Высота |
1 435 |
Вес |
231 |
Ширина |
2 879 |
Глубина |
854 |
Модули
COVER, KEYBOARD ASSY. -2/3
ROLL ASSY.
CARRIAGE -4/5
TAKE-UP DEVECE ASSY. -1/2
COVER, KEYBOARD ASSY. -1/3
Y-DRIVE
CARRIAGE -1/5
Y-BAR -1/2
CARRIAGE -5/5
INK CARTRIDGE
INK PUMP, AIR PUMP
WIPER
ELECTRICAL DEVICE
STATION -1/2
PRINTER FRAME -2/2
PLATEN -2/3
CARRIAGE -2/5
X-DRIVE
BEAR ASSY.
COVER, KEYBOARD ASSY. -3/3
PLATEN -1/3
CAP CLEANING
LEG
CARRIAGE -3/5
PLATEN -3/3
TAKE-UP DEVECE ASSY. -2/2
CLAMP
PRINTER FRAME -1/2
Y-BAR -2/2
STATION -2/2
Детали X-DRIVE
| Деталь: | Cartridge guide 200 |
| Парткод: | M514780 |
| Деталь: | Head guard L |
| Парткод: | M602118 |
| Деталь: | Cartridge BKT 200 |
| Парткод: | M514781 |
| Деталь: | Y cover 200C160 |
| Парткод: | M514771 |
| Деталь: | Y cover 200C130 |
| Парткод: | M514817 |
| Деталь: | Mimaki name plate |
| Парткод: | M602402 |
| Деталь: | Plug cushion rubber |
| Парткод: | TM-96-10 |
| Деталь: | Y cover 200C160 |
| Парткод: | M514770 |
| Деталь: | Y cover 200C130 |
| Парткод: | M514816 |
| Деталь: | U-fan cable 160 assy. |
| Парткод: | E106824 |
| Деталь: | U-fun cable 130 assy. |
| Парткод: | E106847 |
| Деталь: | Roof fun assy. |
| Парткод: | E106963 |
| Деталь: | Finger guard of caliber 80mm |
| Парткод: | 109-049C |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000037 |
| Деталь: | Y cover 200C160 |
| Парткод: | M514772 |
| Деталь: | Y cover 200C130 |
| Парткод: | M514818 |
| Деталь: | Front cover 200L160 |
| Парткод: | M602859 |
| Деталь: | Front cover 200L130 |
| Парткод: | M602862 |
| Деталь: | Cover fulcrum pin |
| Парткод: | M205599 |
| Деталь: | Cover fulcrum pin bracket |
| Парткод: | M503978 |
| Деталь: | Switch dog R |
| Парткод: | M507518 |
| Деталь: | Switch dog L |
| Парткод: | M507519 |
| Деталь: | Roll holder Lv2 assy. 33 |
| Парткод: | MP-M007897 |
| Деталь: | Roll shaft collar |
| Парткод: | M201607 |
| Деталь: | Roll holder shaft L |
| Парткод: | M203641 |
| Деталь: | Roll base 2 (S) |
| Парткод: | M601186 |
| Деталь: | Extension bushing 38 |
| Парткод: | M601190 |
| Деталь: | Roll damper bracket |
| Парткод: | M506944 |
| Деталь: | ROTARY DAMPER |
| Парткод: | FRT-G2-200G2 |
| Деталь: | Roll holder G |
| Парткод: | M600686 |
| Деталь: | Roll holder R assy. 33 |
| Парткод: | MP-M007464 |
| Деталь: | Roll holder gear |
| Парткод: | M601168 |
| Деталь: | Roll stopper |
| Парткод: | M508804 |
| Деталь: | Bearing holder screw |
| Парткод: | M400233 |
| Деталь: | Belt screw |
| Парткод: | M400284 |
| Деталь: | Roll stopper A |
| Парткод: | M601087 |
| Деталь: | Roll stopper base |
| Парткод: | M508803 |
| Деталь: | Roll stopper spring 2 |
| Парткод: | M800604 |
| Деталь: | Height adjusting pin |
| Парткод: | M203314 |
| Деталь: | Pin guide |
| Парткод: | M601050 |
| Деталь: | Level detecting magnetic sensor |
| Парткод: | MP-E300599 |
| Деталь: | Sub tank BKT |
| Парткод: | M514691 |
| Деталь: | W-filter assy. |
| Парткод: | M0123320 |
| Деталь: | W-filter kit |
| Парткод: | SPA-0187 |
| Деталь: | Gen5 head assy. |
| Парткод: | MP-M012352 |
| Деталь: | Fluorine tube special (03x05) |
| Парткод: | MP-HSJPE3-MMK35 |
| Деталь: | Male plug |
| Парткод: | MTLLP-1 |
| Деталь: | Female panel mount |
| Парткод: | FTLLB220-1 |
| Деталь: | Color cord ring (white) |
| Парткод: | CCLR-1 |
| Деталь: | Panel nut (white) |
| Парткод: | LNS-1 |
| Деталь: | Ear extract port stay |
| Парткод: | M514989 |
| Деталь: | Wind-up left (s) v2 assy. 33 |
| Парткод: | MP-M007898 |
| Деталь: | BEARING |
| Парткод: | 6806ZZNR |
| Деталь: | Roll base 2 (BR) |
| Парткод: | M601185 |
| Деталь: | HOLDER SHAFT |
| Парткод: | M202118 |
| Деталь: | Roll holder |
| Парткод: | M600500 |
| Деталь: | Extension bushing 38 |
| Парткод: | M601190 |
| Деталь: | BACK COVER |
| Парткод: | M514785 |
| Деталь: | CARTRIDGE COVER |
| Парткод: | M514778 |
| Деталь: | Left maintenance cover U |
| Парткод: | M514773 |
| Деталь: | Plastic-head screw |
| Парткод: | MM-000633 |
| Деталь: | Heater connecter cover 200 |
| Парткод: | M514775 |
| Деталь: | MS cover L |
| Парткод: | M514777 |
| Деталь: | Positive pressure adjust valve label |
| Парткод: | M905916 |
| Деталь: | Negative pressure adjust valve label |
| Парткод: | M905917 |
| Деталь: | Lock edge saddle |
| Парткод: | MM-001270 |
| Деталь: | Throttle valve |
| Парткод: | MP-JNU6 |
| Деталь: | PN tube |
| Парткод: | MP-PN-4-64 |
| Деталь: | Filter (for vacuum) |
| Парткод: | MP-VFU3-66P |
| Деталь: | MS cover C |
| Парткод: | M514776 |
| Деталь: | Left maintenance cover D |
| Парткод: | M514774 |
| Деталь: | X pulley cover |
| Парткод: | M602226 |
| Деталь: | Left cover 200 |
| Парткод: | M514768 |
| Деталь: | Left cover 200 |
| Парткод: | M602839 |
| Деталь: | Back cover LD |
| Парткод: | M514786 |
| Деталь: | Heater PCB partition plate |
| Парткод: | M514986 |
| Деталь: | Y drive belt 160 LX |
| Парткод: | M801469 |
| Деталь: | Y drive belt 130 LX |
| Парткод: | M801472 |
| Деталь: | Belt holder 1 |
| Парткод: | M400160 |
| Деталь: | Black screw for belt |
| Парткод: | M400284 |
| Деталь: | Belt holder S |
| Парткод: | M503786 |
| Деталь: | Belt holder |
| Парткод: | M400161 |
| Деталь: | D bracket U |
| Парткод: | M502708 |
| Деталь: | O-ring |
| Парткод: | MM-000179 |
| Деталь: | Y drive pulley assy. |
| Парткод: | M006891 |
| Деталь: | Belt with cleaning teeth |
| Парткод: | 150S2M380G |
| Деталь: | D BKT 200 |
| Парткод: | M514503 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000032 |
| Деталь: | BEARING |
| Парткод: | F607ZZ |
| Деталь: | YM top plate TM |
| Парткод: | M514699 |
| Деталь: | YM stud 200 |
| Парткод: | M207264 |
| Деталь: | Y motor BKT 200 |
| Парткод: | M514504 |
| Деталь: | Belt tension SP |
| Парткод: | M801448 |
| Деталь: | DM pulley |
| Парткод: | M202666 |
| Деталь: | DC motor encoder |
| Парткод: | E300882 |
| Деталь: | Y-axis motor assy. 33 |
| Парткод: | MP-M012378 |
| Деталь: | Y-T fulcrum pin |
| Парткод: | M202842 |
| Деталь: | Y-T base 200 |
| Парткод: | M514700 |
| Деталь: | Y-T pulley bracket 30 |
| Парткод: | M510408 |
| Деталь: | Y spring |
| Парткод: | M800569 |
| Деталь: | Y spring plate 30 |
| Парткод: | M510620 |
| Деталь: | Y-T pulley assy. |
| Парткод: | M006977 |
| Деталь: | HDC cover |
| Парткод: | M514714 |
| Деталь: | HDC fan filter |
| Парткод: | M801493 |
| Деталь: | HDC fan filter cover |
| Парткод: | M514726 |
| Деталь: | Head cover R |
| Парткод: | M514788 |
| Деталь: | Head filter stay |
| Парткод: | M515274 |
| Деталь: | Head filter holder |
| Парткод: | M515275 |
| Деталь: | HEAD COVER |
| Парткод: | M514790 |
| Деталь: | Lure lock cover |
| Парткод: | M515308 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000033 |
| Деталь: | Head fan filter cover |
| Парткод: | M516361 |
| Деталь: | Head fan filter |
| Парткод: | M801563 |
| Деталь: | Head cover L |
| Парткод: | M514789 |
| Деталь: | Cutter assy. |
| Парткод: | M011866 |
| Деталь: | Cutting cutter assy. |
| Парткод: | M011867 |
| Деталь: | Cutter blade holder |
| Парткод: | M601086 |
| Деталь: | Cutter L |
| Парткод: | M201535 |
| Деталь: | Cutter roller |
| Парткод: | M601085 |
| Деталь: | Cutter screw |
| Парткод: | M400281 |
| Деталь: | Media cutter guide pin |
| Парткод: | M205601 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000035 |
| Деталь: | Cutter BKT 200 |
| Парткод: | M514477 |
| Деталь: | Cutter guard 200 |
| Парткод: | M515049 |
| Деталь: | CUTTER SOLENOID ASSY. |
| Парткод: | E106861 |
| Деталь: | Cutter spring 2 |
| Парткод: | M800665 |
| Деталь: | CUTTER HOLDER |
| Парткод: | M602125 |
| Деталь: | Y bar 160 LX |
| Парткод: | M514501 |
| Деталь: | Y bar 130 LX |
| Парткод: | M514810 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000039 |
| Деталь: | Bear support plate |
| Парткод: | M515048 |
| Деталь: | Finger guard front 160 |
| Парткод: | M514987 |
| Деталь: | Finger guard front 130 |
| Парткод: | M514999 |
| Деталь: | Scale hook 200 |
| Парткод: | M514728 |
| Деталь: | Scale spring |
| Парткод: | M800565 |
| Деталь: | Scale holder L 200 |
| Парткод: | M514727 |
| Деталь: | Scale base L 200 |
| Парткод: | M514505 |
| Деталь: | Y starting point sensor dog |
| Парткод: | M514507 |
| Деталь: | Y bracket reinforcing plate |
| Парткод: | M508900 |
| Деталь: | LM guide |
| Парткод: | SSR15XW2GE+2500LY |
| Деталь: | Y bar 160LX |
| Парткод: | SSR15XW2GE+2260LY |
| Деталь: | Scale base dog |
| Парткод: | M514506 |
| Деталь: | Linear encoder scale 2499 |
| Парткод: | MP-E300888 |
| Деталь: | Linear encoder scale 2250 |
| Парткод: | MP-E300889 |
| Деталь: | Scale holder R |
| Парткод: | M503398 |
| Деталь: | Scale holder |
| Парткод: | M601077 |
| Деталь: | Scale stopper |
| Парткод: | M602224 |
| Деталь: | Slider 200 |
| Парткод: | M514481 |
| Деталь: | Oil less 80 flange bush |
| Парткод: | MM-001339 |
| Деталь: | Head up and down lever AL |
| Парткод: | M207303 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000037 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000035 |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | MP-OJ-6505-N2 |
| Деталь: | Linear encoder cable assy. |
| Парткод: | E106830 |
| Деталь: | 150 lpi encoder PCB assy. |
| Парткод: | MP-E103852 |
| Деталь: | Linear sensor BKT |
| Парткод: | M514476 |
| Деталь: | Head up and down sensor BKT |
| Парткод: | M514475 |
| Деталь: | Head base BKT |
| Парткод: | M514480 |
| Деталь: | CL stopper C 100 |
| Парткод: | M801115 |
| Деталь: | Black screw for belt |
| Парткод: | M400284 |
| Деталь: | Head up and down base |
| Парткод: | M514474 |
| Деталь: | Corrugated spring pin |
| Парткод: | MM-000653 |
| Деталь: | Head up and down base |
| Парткод: | M207304 |
| Деталь: | Head up and down shaft |
| Парткод: | M207263 |
| Деталь: | Head up and down sensor dog |
| Парткод: | M514479 |
| Деталь: | Locking edge saddle |
| Парткод: | MM-000902 |
| Деталь: | Head adjust plate spring 200 |
| Парткод: | M514478 |
| Деталь: | Head adjust slide nut |
| Парткод: | M207262 |
| Деталь: | Pusher spring |
| Парткод: | M800966 |
| Деталь: | AD pusher |
| Парткод: | M602123 |
| Деталь: | Carriage base 200 |
| Парткод: | M400467 |
| Деталь: | Head base R |
| Парткод: | M514473 |
| Деталь: | Inclination adjustment lever |
| Парткод: | M602126 |
| Деталь: | Head inclination cam |
| Парткод: | M207034 |
| Деталь: | Photo sensor ROHS |
| Парткод: | MP-SG113 |
| Деталь: | Head base L |
| Парткод: | M514472 |
| Деталь: | Carriage inclination SP200 |
| Парткод: | M801468 |
| Деталь: | LED wiring BKT |
| Парткод: | M514762 |
| Деталь: | Locking edge saddle |
| Парткод: | TSB-3509 |
| Деталь: | Locking edge saddle |
| Парткод: | MM-000902 |
| Деталь: | Cartridge holder B |
| Парткод: | M514694 |
| Деталь: | FFC 1.25-16P-1200 |
| Парткод: | E300771 |
| Деталь: | Ink LED PCB assy. |
| Парткод: | E106761 |
| Деталь: | LED cover |
| Парткод: | M514779 |
| Деталь: | Cartridge base BKT 200 |
| Парткод: | M514693 |
| Деталь: | Cartridge base U |
| Парткод: | M602130 |
| Деталь: | Cartridge base D |
| Парткод: | M602131 |
| Деталь: | LINK |
| Парткод: | M601336 |
| Деталь: | Snap pin A |
| Парткод: | M801089 |
| Деталь: | Ink cartridge solenoid |
| Парткод: | MP-E300816 |
| Деталь: | Cartridge solenoid BKT |
| Парткод: | M510211 |
| Деталь: | Valve N-3 M6 assy. |
| Парткод: | M007124 |
| Деталь: | Cartridge flame |
| Парткод: | M602128 |
| Деталь: | Cartridge guide |
| Парткод: | M602129 |
| Деталь: | Cartridge sensor |
| Парткод: | MP-1033477 |
| Деталь: | ID contact PCB CN032 assy. |
| Парткод: | MP-E105363 |
| Деталь: | Ink ID cable assy. |
| Парткод: | E106828 |
| Деталь: | Tube, Supply, f2 |
| Парткод: | 1080249 |
| Деталь: | Joint screw M6 |
| Парткод: | 1033482 |
| Деталь: | RS O-ring f2.16x1.4 |
| Парткод: | M700326 |
| Деталь: | T joint M6 |
| Парткод: | M602148 |
| Деталь: | Rubber stopper |
| Парткод: | M700782 |
| Деталь: | T joint M6 assy. |
| Парткод: | M011892 |
| Деталь: | Ink SOL cable assy. |
| Парткод: | E106827 |
| Деталь: | Valve cap |
| Парткод: | M601215 |
| Деталь: | Cartridge valve spring 120 |
| Парткод: | M800684 |
| Деталь: | Valve spring washer |
| Парткод: | M204082 |
| Деталь: | Rubber valve pin |
| Парткод: | M204083 |
| Деталь: | Rubber valve |
| Парткод: | M700350 |
| Деталь: | Valve base N-3 |
| Парткод: | M601816 |
| Деталь: | M700323 RS O-ring f1.1x2.2 |
| Парткод: | MM-000001 |
| Деталь: | Ink needle |
| Парткод: | 1033462 |
| Деталь: | Pressure control pump assy. |
| Парткод: | MP-E106684 |
| Деталь: | TUBE |
| Парткод: | 4x6-TP-SX |
| Деталь: | DCM cable assy. |
| Парткод: | E106825 |
| Деталь: | Locking edge saddle |
| Парткод: | MM-000043 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000033 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000039 |
| Деталь: | Air pump BKT |
| Парткод: | M514680 |
| Деталь: | PN tube 2.54 milky 20M roll |
| Парткод: | MP-PN-4-42.5 |
| Деталь: | Lure fitting |
| Парткод: | VFI246 |
| Деталь: | Lure fitting |
| Парткод: | VFT406 |
| Деталь: | Bolt pressing BKT |
| Парткод: | M514709 |
| Деталь: | Chamber bottle assy. |
| Парткод: | M011886 |
| Деталь: | Lure fitting |
| Парткод: | MTLL-420-1 |
| Деталь: | Tube pump 11 all assy. |
| Парткод: | M011574 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000037 |
| Деталь: | Pump holder plate |
| Парткод: | M514679 |
| Деталь: | Tube pump 1 assy. |
| Парткод: | MP-M011571 |
| Деталь: | Pump sheet metal |
| Парткод: | M514913 |
| Деталь: | Oil less 80 flange bush |
| Парткод: | MM-001339 |
| Деталь: | PUMP GEAR |
| Парткод: | M602844 |
| Деталь: | L rubber |
| Парткод: | M700637 |
| Деталь: | Pump roller |
| Парткод: | M207290 |
| Деталь: | Lure fitting |
| Парткод: | FTLL013-6 |
| Деталь: | Lure fitting |
| Парткод: | MLRL013-6 |
| Деталь: | Lock ring (black) |
| Парткод: | FSLLR-2 |
| Деталь: | TUBE |
| Парткод: | 3x5-TP-S |
| Деталь: | Pump base |
| Парткод: | M602554 |
| Деталь: | Motor all assy. |
| Парткод: | M011578 |
| Деталь: | Pump motor assy. |
| Парткод: | M011572 |
| Деталь: | Stepping motor |
| Парткод: | MP-E300495 |
| Деталь: | Pump motor gear |
| Парткод: | M400210 |
| Деталь: | Motor sheet metal |
| Парткод: | M514914 |
| Деталь: | Pump middle slowdown gear |
| Парткод: | M602804 |
| Деталь: | Pump cable assy. |
| Парткод: | E106826 |
| Деталь: | Ink guard |
| Парткод: | M514993 |
| Деталь: | Wiper guide |
| Парткод: | M514857 |
| Деталь: | Wiper guide shaft up |
| Парткод: | M207314 |
| Деталь: | WP base |
| Парткод: | M602894 |
| Деталь: | Wiper guide shaft down |
| Парткод: | M207315 |
| Деталь: | Wiper kit |
| Парткод: | SPA-0184 |
| Деталь: | SHAFT HOLDER |
| Парткод: | M602898 |
| Деталь: | Wiper belt holder |
| Парткод: | M514875 |
| Деталь: | BEARING |
| Парткод: | F684ZZ |
| Деталь: | Wiper |
| Парткод: | M400302 |
| Деталь: | Drive Shaft |
| Парткод: | M207317 |
| Деталь: | COLLAR |
| Парткод: | MM-001195 |
| Деталь: | Pump motor gear |
| Парткод: | M400210 |
| Деталь: | Drive shaft BKT |
| Парткод: | M514850 |
| Деталь: | Wiper pulley B |
| Парткод: | M601914 |
| Деталь: | Wiper driven BKT |
| Парткод: | M514868 |
| Деталь: | Belt tension BKT |
| Парткод: | M514854 |
| Деталь: | Pump middle gear |
| Парткод: | M601044 |
| Деталь: | Drive motor |
| Парткод: | M514849 |
| Деталь: | Stepping motor |
| Парткод: | MP-E300495 |
| Деталь: | S motor cable assy. |
| Парткод: | E106816 |
| Деталь: | WP height adjust BKT |
| Парткод: | M514996 |
| Деталь: | Ink slope |
| Парткод: | M514858 |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | MP-OJ-6505-N2 |
| Деталь: | Electrical box exhaust cover 200 |
| Парткод: | M514720 |
| Деталь: | Electrical box cover 200 |
| Парткод: | M514721 |
| Деталь: | Electrical box 200 |
| Парткод: | M514719 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000033 |
| Деталь: | One touch bushing |
| Парткод: | MM-000674 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000037 |
| Деталь: | Square bushing |
| Парткод: | MM-000899 |
| Деталь: | FFC holder |
| Парткод: | M514985 |
| Деталь: | Square bushing |
| Парткод: | MM-000900 |
| Деталь: | EPL main PCB assy. |
| Парткод: | MP-E000011 |
| Деталь: | Central IO PCB assy. |
| Парткод: | MP-E000013 |
| Деталь: | SW power supply(15W-5W) |
| Парткод: | MP-LFA15F-5-GJ1 |
| Деталь: | NOISE FILTER |
| Парткод: | EAM-16-000 |
| Деталь: | Flat cable clamp |
| Парткод: | MM-000049 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000039 |
| Деталь: | Electrical box partition plate |
| Парткод: | M514724 |
| Деталь: | Lock edge saddle |
| Парткод: | MM-001270 |
| Деталь: | SW power supply(600W-36V) |
| Парткод: | MP-PBA600F-36 |
| Деталь: | NF-POW cable assy. |
| Парткод: | E106811 |
| Деталь: | AC switch junction cable assy. |
| Парткод: | E106952 |
| Деталь: | INLET ASSY. |
| Парткод: | E106809 |
| Деталь: | SWITCH |
| Парткод: | AJ8202WWF |
| Деталь: | USB junction side cover 200 |
| Парткод: | M514718 |
| Деталь: | DC-POW cable assy. |
| Парткод: | E106812 |
| Деталь: | Main HDC cable assy. |
| Парткод: | E106829 |
| Деталь: | Main HDC cable 130 assy. |
| Парткод: | E106859 |
| Деталь: | FFC 1.00-30P-3600 |
| Парткод: | MP-E300883 |
| Деталь: | FFC 1.00-30P-3400 |
| Парткод: | MP-E300884 |
| Деталь: | P1.25-20-250 |
| Парткод: | E300777 |
| Деталь: | P1.0-10-1100mm |
| Парткод: | E300604 |
| Деталь: | Thermistor junction cable assy. |
| Парткод: | E106820 |
| Деталь: | DDR 2 PRAM (1GB) PCB assy. |
| Парткод: | MP-E105986 |
| Деталь: | IO cable assy. |
| Парткод: | E106821 |
| Деталь: | Cascade short 13 assy. |
| Парткод: | E106086 |
| Деталь: | C-pad |
| Парткод: | M801445 |
| Деталь: | C-pad 2 |
| Парткод: | M801491 |
| Деталь: | C slider 200 |
| Парткод: | M602903 |
| Деталь: | Cap slider spring |
| Парткод: | M801470 |
| Деталь: | Cap slider base 200 |
| Парткод: | M602825 |
| Деталь: | Cap rubber holder 5 |
| Парткод: | M514471 |
| Деталь: | G5CP mesh |
| Парткод: | M514968 |
| Деталь: | Cap rubber GEN5 |
| Парткод: | MP-M700666 |
| Деталь: | Cap base GEN5 |
| Парткод: | MP-M602833 |
| Деталь: | Cap spring 200 |
| Парткод: | M801490 |
| Деталь: | TUBE |
| Парткод: | 2x4-TP-SX |
| Деталь: | Lure fitting |
| Парткод: | VFY206 |
| Деталь: | C base BKT |
| Парткод: | M514453 |
| Деталь: | C adjust BKT L |
| Парткод: | M514455 |
| Деталь: | C adjust BKT R |
| Парткод: | M514454 |
| Деталь: | WP height adjust RACK |
| Парткод: | M514997 |
| Деталь: | C base pad |
| Парткод: | M801441 |
| Деталь: | Ink guide holder |
| Парткод: | M514995 |
| Деталь: | Ink guide |
| Парткод: | M514883 |
| Деталь: | Waste ink tray |
| Парткод: | M514470 |
| Деталь: | Station base |
| Парткод: | M514450 |
| Деталь: | ST spacer 200 |
| Парткод: | M514686 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000033 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000037 |
| Деталь: | Female lure lock fitting (P) |
| Парткод: | VPRM308 |
| Деталь: | Male lure lock fitting (P) |
| Парткод: | VPRF308 |
| Деталь: | Head air extract |
| Парткод: | M206680 |
| Деталь: | Head height plate L |
| Парткод: | M514997 |
| Деталь: | Head height plate H |
| Парткод: | M514483 |
| Деталь: | Lure fitting |
| Парткод: | VFI236 |
| Деталь: | TUBE |
| Парткод: | 3x5-TP-SX |
| Деталь: | Rear cover flame R |
| Парткод: | M514751 |
| Деталь: | PC cartridge base BKT |
| Парткод: | M514687 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000033 |
| Деталь: | KB BKT |
| Парткод: | M514717 |
| Деталь: | KB BKT D |
| Парткод: | M514991 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000039 |
| Деталь: | One touch bushing |
| Парткод: | MM-000673 |
| Деталь: | Locking edge saddle |
| Парткод: | MM-000902 |
| Деталь: | MICRO SWITCH |
| Парткод: | MP-D3M-01K1-3 |
| Деталь: | Switch cover |
| Парткод: | M602228 |
| Деталь: | MAGNET CATCH |
| Парткод: | TL-295-2 |
| Деталь: | Cover sensor junction cable assy. |
| Парткод: | E106950 |
| Деталь: | Cover sensor R cable assy. |
| Парткод: | E106843 |
| Деталь: | S side plate R |
| Парткод: | M514508 |
| Деталь: | Extend flame 160 |
| Парткод: | M514509 |
| Деталь: | Extend flame 130 |
| Парткод: | M514803 |
| Деталь: | Extend flame base plate 160 |
| Парткод: | M514510 |
| Деталь: | P side plate R 2 |
| Парткод: | M514744 |
| Деталь: | Y cover flame R |
| Парткод: | M514747 |
| Деталь: | P side plate R 1 |
| Парткод: | M514495 |
| Деталь: | RUBBER FOOT |
| Парткод: | TK-24 |
| Деталь: | Y bar block |
| Парткод: | M400350 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000037 |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | MP-OJ-6505-N2 |
| Деталь: | S sensor cable assy. |
| Парткод: | E106818 |
| Деталь: | CL sensor BKT |
| Парткод: | M514753 |
| Деталь: | Tank stopper |
| Парткод: | M514754 |
| Деталь: | Black screw for belt |
| Парткод: | M400284 |
| Деталь: | Wiring BKT |
| Парткод: | M514689 |
| Деталь: | Front cover flame R |
| Парткод: | M514716 |
| Деталь: | One touch bushing |
| Парткод: | MM-001162 |
| Деталь: | Maintenance switch cover |
| Парткод: | M514688 |
| Деталь: | Platen cover R160 assy. |
| Парткод: | M011747 |
| Деталь: | Platen cover R130 assy. |
| Парткод: | M011774 |
| Деталь: | Platen cover R160 LX |
| Парткод: | M514497 |
| Деталь: | Platen cover R 130 LX |
| Парткод: | M514807 |
| Деталь: | Platen thermistor R160 |
| Парткод: | E300898 |
| Деталь: | Platen thermistor R130 |
| Парткод: | E300901 |
| Деталь: | Aluminum foil heater R160 |
| Парткод: | E300865 |
| Деталь: | Aluminum foil heater R130 |
| Парткод: | E300869 |
| Деталь: | Platen thermostat R |
| Парткод: | E300878 |
| Деталь: | Thermostat holder R |
| Парткод: | M514698 |
| Деталь: | Platen cover F160 LX base |
| Парткод: | M514695 |
| Деталь: | Platen cover F130 LX base |
| Парткод: | M514805 |
| Деталь: | Voltage switching SW assy. |
| Парткод: | E106970 |
| Деталь: | Platen cover F160 assy. |
| Парткод: | M011746 |
| Деталь: | Platen cover F130 assy. |
| Парткод: | M011773 |
| Деталь: | Thermistor AA 160 |
| Парткод: | E300899 |
| Деталь: | Thermistor AA 130 |
| Парткод: | E300902 |
| Деталь: | Aluminum foil heater A160 |
| Парткод: | E300907 |
| Деталь: | Aluminum foil heater A130 |
| Парткод: | E300908 |
| Деталь: | Platen cover F160 LX |
| Парткод: | M514496 |
| Деталь: | Platen cover F130 LX |
| Парткод: | M514806 |
| Деталь: | Platen thermostat AA |
| Парткод: | E300879 |
| Деталь: | Thermostat holder F2 |
| Парткод: | M514697 |
| Деталь: | F sheet holder U200-160 |
| Парткод: | M515031 |
| Деталь: | F sheet holder U200-130 |
| Парткод: | M515034 |
| Деталь: | Platen F sheet 200-160 |
| Парткод: | M801495 |
| Деталь: | Platen F sheet 200-130 |
| Парткод: | M801496 |
| Деталь: | Sheet SP |
| Парткод: | M800699 |
| Деталь: | F sheet holder base 200-160 |
| Парткод: | M515033 |
| Деталь: | F sheet holder base 200-130 |
| Парткод: | M515036 |
| Деталь: | F sheet holder L200-160 |
| Парткод: | M515032 |
| Деталь: | F sheet holder L200-130 |
| Парткод: | M515035 |
| Деталь: | 2-2way 2-3way solenoid valve |
| Парткод: | MP-E300918 |
| Деталь: | TUBE |
| Парткод: | 4x6-TP-SX |
| Деталь: | Lure fitting |
| Парткод: | VFI246 |
| Деталь: | PN tube 2.54 milky 20M roll |
| Парткод: | MP-PN-4-42.5 |
| Деталь: | TUBE |
| Парткод: | 2x4-TP-SX |
| Деталь: | Lure fitting |
| Парткод: | VFT206 |
| Деталь: | Lure fitting |
| Парткод: | VFI346 |
| Деталь: | TUBE |
| Парткод: | 3x5-TP-SX |
| Деталь: | Multi port connector F type |
| Парткод: | VFF306 |
| Деталь: | Multi port connector all around type |
| Парткод: | VM4L306 |
| Деталь: | Vent filter |
| Парткод: | MP-LCF-59400 |
| Деталь: | Lure fitting |
| Парткод: | VRMP6 |
| Деталь: | Lure fitting |
| Парткод: | VPRF406 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000033 |
| Деталь: | Filter BKT |
| Парткод: | M514711 |
| Деталь: | Filter Holder |
| Парткод: | M514484 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000037 |
| Деталь: | Negative pressure sensor PCB assy. |
| Парткод: | MP-E105303 |
| Деталь: | Positive pressure sensor PCB assy. |
| Парткод: | MP-E105304 |
| Деталь: | Pressure sensor cable assy. |
| Парткод: | E106834 |
| Деталь: | Tube 100M |
| Парткод: | MP-K30B101157-00 |
| Деталь: | Tube, Supply, f2 |
| Парткод: | MP-1080249 |
| Деталь: | Rotary panel mount male |
| Парткод: | MLRLB220 |
| Деталь: | Lure fitting |
| Парткод: | VRM306 |
| Деталь: | Lock ring (black) |
| Парткод: | FSLLR-2 |
| Деталь: | Male plug |
| Парткод: | MTLLP-1 |
| Деталь: | Lure fitting |
| Парткод: | FTLL220-1 |
| Деталь: | Supply tube 03 |
| Парткод: | 1083732 |
| Деталь: | Tank film holder |
| Парткод: | M514670 |
| Деталь: | 200 Sub tank assy. |
| Парткод: | MP-M012353 |
| Деталь: | 200 Sub tank assy. R |
| Парткод: | MP-M012354 |
| Деталь: | PF roller 160 LX |
| Парткод: | M207298 |
| Деталь: | PF roller 130 LX |
| Парткод: | M207299 |
| Деталь: | BR holder 200 SL assy. |
| Парткод: | M011743 |
| Деталь: | PF coupling C |
| Парткод: | M206109 |
| Деталь: | BR holder 200 S assy. |
| Парткод: | M011742 |
| Деталь: | Joint axis |
| Парткод: | M207307 |
| Деталь: | X pulley bracket |
| Парткод: | M508899 |
| Деталь: | BEARING |
| Парткод: | MF148ZZ |
| Деталь: | TN15-160 pulley |
| Парткод: | M203155 |
| Деталь: | Synchronize belt TN |
| Парткод: | 250-TN15-10 |
| Деталь: | X-axis motor assy. 33 |
| Парткод: | MP-M007619 |
| Деталь: | Servo motor assy. (X) |
| Парткод: | E300532 |
| Деталь: | TN15-20 pulley |
| Парткод: | M203154 |
| Деталь: | XY motor cable 160 assy. |
| Парткод: | E106813 |
| Деталь: | XY motor cable 130 assy. |
| Парткод: | E106814 |
| Деталь: | XM bracket |
| Парткод: | M508901 |
| Деталь: | BEARING |
| Парткод: | MF105ZZ |
| Деталь: | X belt tension spring |
| Парткод: | M800977 |
| Деталь: | Cable bear 300 assy.160 |
| Парткод: | M012139 |
| Деталь: | Cable bear 300 assy.130 |
| Парткод: | M012140 |
| Деталь: | Bear buffer material 160LX |
| Парткод: | M801471 |
| Деталь: | Bear buffer material 130LX |
| Парткод: | M801473 |
| Деталь: | Flat cable clamp |
| Парткод: | FCS-3015 |
| Деталь: | Locking edge saddle |
| Парткод: | TSB-3509 |
| Деталь: | Bear guide 160 LX |
| Парткод: | M514761 |
| Деталь: | Bear guide 130 LX |
| Парткод: | M514811 |
| Деталь: | Bear guide warning cover 160 LX |
| Парткод: | M514763 |
| Деталь: | Bear guide warning cover 130 LX |
| Парткод: | M514812 |
| Деталь: | M904096 ink tube tag 1-1 |
| Парткод: | MM-000115 |
| Деталь: | M904097 ink tube tag 1-2 |
| Парткод: | MM-000116 |
| Деталь: | M904098 ink tube tag 1-3 |
| Парткод: | MM-000117 |
| Деталь: | M904099 ink tube tag 1-4 |
| Парткод: | MM-000118 |
| Деталь: | M904100 ink tube tag 1-5 |
| Парткод: | MM-000119 |
| Деталь: | M904101 ink tube tag 1-6 |
| Парткод: | MM-000120 |
| Деталь: | M904102 ink tube tag 1-7 |
| Парткод: | MM-000121 |
| Деталь: | M904102 ink tube tag 1-8 |
| Парткод: | MM-000122 |
| Деталь: | Tube, Supply, f2 |
| Парткод: | MP-1080249 |
| Деталь: | PN tube 2.54 milky 20M roll |
| Парткод: | MP-PN-4-42.5 |
| Деталь: | Bear absorption pad |
| Парткод: | M801492 |
| Деталь: | Flat cable clamp |
| Парткод: | MM-000049 |
| Деталь: | Y cover RR |
| Парткод: | M514787 |
| Деталь: | Plug cushion rubber |
| Парткод: | TM-96-1 |
| Деталь: | Right maintenance cover U |
| Парткод: | M514766 |
| Деталь: | Cover fulcrum pin |
| Парткод: | M205599 |
| Деталь: | Cover fulcrum pin bracket |
| Парткод: | M503978 |
| Деталь: | MAGNET CATCH |
| Парткод: | TL-295-2 |
| Деталь: | Back cover R |
| Парткод: | M514784 |
| Деталь: | PC cartridge cover 200 |
| Парткод: | M514769 |
| Деталь: | Electrical BOX cover D |
| Парткод: | M514782 |
| Деталь: | Right cover 200 |
| Парткод: | M514767 |
| Деталь: | Right cover 200 |
| Парткод: | M602838 |
| Деталь: | KB cover |
| Парткод: | M602840 |
| Деталь: | LCD window |
| Парткод: | M600520 |
| Деталь: | Keyboard PCB assy. |
| Парткод: | MP-E106802 |
| Деталь: | KEY TOP |
| Парткод: | M602135 |
| Деталь: | Remote switch assy. |
| Парткод: | E106839 |
| Деталь: | KB sheet 200 |
| Парткод: | M908510 |
| Деталь: | Black screw for belt |
| Парткод: | M400284 |
| Деталь: | Right maintenance cover D |
| Парткод: | M514742 |
| Деталь: | Right maintenance cover C |
| Парткод: | M514765 |
| Деталь: | A heater cover 160A |
| Парткод: | M514757 |
| Деталь: | A heater cover 130A |
| Парткод: | M514808 |
| Деталь: | Handle assy. |
| Парткод: | M006193 |
| Деталь: | Drying fan side plate R |
| Парткод: | M515046 |
| Деталь: | Corner guard |
| Парткод: | M700678 |
| Деталь: | Black screw for belt |
| Парткод: | M400284 |
| Деталь: | 10.9 flange socket |
| Парткод: | SCM435 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000032 |
| Деталь: | Drying fan side plate L |
| Парткод: | M515047 |
| Деталь: | Heater guard 160 |
| Парткод: | M515009 |
| Деталь: | Heater guard 130 |
| Парткод: | M515021 |
| Деталь: | Heater BKT B |
| Парткод: | M515004 |
| Деталь: | Carbon heater 800 |
| Парткод: | E300912 |
| Деталь: | Carbon heater 500 |
| Парткод: | E300913 |
| Деталь: | Heater base B |
| Парткод: | M515002 |
| Деталь: | Reflector 160 |
| Парткод: | M515000 |
| Деталь: | Reflector 130 |
| Парткод: | M515012 |
| Деталь: | Tube end |
| Парткод: | M400263 |
| Деталь: | THERMOSTAT |
| Парткод: | 03EN3366A70 |
| Деталь: | Fan holder BKT 160 |
| Парткод: | M515014 |
| Деталь: | Fan holder BKT 130 |
| Парткод: | M515017 |
| Деталь: | Push-in type fixing metal fittings |
| Парткод: | TM2PWH25-C |
| Деталь: | T sensor holder |
| Парткод: | M515006 |
| Деталь: | Non-contact temp sensor |
| Парткод: | MP-E300915 |
| Деталь: | T sensor BKT |
| Парткод: | M515005 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000035 |
| Деталь: | Reflector stay |
| Парткод: | M515007 |
| Деталь: | Heater fan cover reinforcement plate |
| Парткод: | M515008 |
| Деталь: | Heater wiring BKT 160 |
| Парткод: | M515015 |
| Деталь: | Heater wiring BKT 130 |
| Парткод: | M515018 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000037 |
| Деталь: | A-fan cable 160 assy. |
| Парткод: | E106822 |
| Деталь: | A-fan cable 130 assy. |
| Парткод: | E106856 |
| Деталь: | A drying fan assy. |
| Парткод: | E106804 |
| Деталь: | Heater fan cover 160 |
| Парткод: | M515010 |
| Деталь: | Heater fan cover 130 |
| Парткод: | M515023 |
| Деталь: | Heater fan cover BKT |
| Парткод: | M515011 |
| Деталь: | Plug cushion rubber |
| Парткод: | TM-96-1 |
| Деталь: | Outside heater junction cable 160 assy. |
| Парткод: | E106966 |
| Деталь: | Outside heater junction cable 130 assy. |
| Парткод: | E106967 |
| Деталь: | Outside heater relay cable assy. |
| Парткод: | E106965 |
| Деталь: | Steady brace |
| Парткод: | M508797 |
| Деталь: | Cartridge guide U |
| Парткод: | M601817 |
| Деталь: | Cartridge guide D |
| Парткод: | M601818 |
| Деталь: | PC cartridge base |
| Парткод: | M508793 |
| Деталь: | PC cartridge tray |
| Парткод: | M602227 |
| Деталь: | Ink cartridge solenoid |
| Парткод: | MP-E300816 |
| Деталь: | Snap pin A |
| Парткод: | M801089 |
| Деталь: | LINK |
| Парткод: | M601336 |
| Деталь: | Solenoid bracket |
| Парткод: | M507348 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000033 |
| Деталь: | Valve N-3 M6 assy. |
| Парткод: | M007124 |
| Деталь: | Joint screw M6 |
| Парткод: | 1033482 |
| Деталь: | RS O-ring f2.16x1.4 |
| Парткод: | M700326 |
| Деталь: | Cartridge frame V |
| Парткод: | M601182 |
| Деталь: | ID contact PCB CN032 assy. |
| Парткод: | MP-E105363 |
| Деталь: | Cartridge plate spring |
| Парткод: | M800857 |
| Деталь: | Cartridge sensor |
| Парткод: | MP-1033477 |
| Деталь: | Ink needle |
| Парткод: | 1033462 |
| Деталь: | M700323 RS O-ring f1.1x2.2 |
| Парткод: | MM-000001 |
| Деталь: | Valve base N-3 |
| Парткод: | M601816 |
| Деталь: | Rubber valve |
| Парткод: | M700350 |
| Деталь: | Rubber valve pin |
| Парткод: | M204083 |
| Деталь: | Valve spring washer |
| Парткод: | M204082 |
| Деталь: | Cartridge valve spring 120 |
| Парткод: | M800684 |
| Деталь: | Valve cap |
| Парткод: | M601215 |
| Деталь: | 160 Sheet metal leg stay 30 |
| Парткод: | M510437 |
| Деталь: | 130 Sheet metal leg stay 30 |
| Парткод: | M510438 |
| Деталь: | SCM435 10.9 flange socket |
| Парткод: | MM-001051 |
| Деталь: | Roll guide shaft retainer plate |
| Парткод: | M514676 |
| Деталь: | Roll guide BKT 200B |
| Парткод: | M514675 |
| Деталь: | Right leg |
| Парткод: | M514893 |
| Деталь: | Tank tray |
| Парткод: | M602229 |
| Деталь: | CASTER |
| Парткод: | BWP-50BN |
| Деталь: | Roll guide BKT 200A |
| Парткод: | M514674 |
| Деталь: | Roll guide 160 |
| Парткод: | M205988 |
| Деталь: | Roll guide 130 |
| Парткод: | M205989 |
| Деталь: | Reinforcing plate for leg |
| Парткод: | M514894 |
| Деталь: | Left leg |
| Парткод: | M514892 |
| Деталь: | Bear BKT |
| Парткод: | M514712 |
| Деталь: | Flat cable clamp |
| Парткод: | MM-000050 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000039 |
| Деталь: | Carriage support plate R |
| Парткод: | M515044 |
| Деталь: | Carriage fan assy. |
| Парткод: | E106806 |
| Деталь: | HDC PCB assy. |
| Парткод: | MP-E106738 |
| Деталь: | FFC holder |
| Парткод: | M514985 |
| Деталь: | HD BKT |
| Парткод: | M514710 |
| Деталь: | Carriage support plate L |
| Парткод: | M515045 |
| Деталь: | Locking edge saddle |
| Парткод: | MM-001270 |
| Деталь: | Head harness sponge |
| Парткод: | M801565 |
| Деталь: | Head cable assy. |
| Парткод: | E106831 |
| Деталь: | Head PCB BKT |
| Парткод: | M514708 |
| Деталь: | Jam sensor BKT R |
| Парткод: | M514486 |
| Деталь: | Locking edge saddle |
| Парткод: | MM-000902 |
| Деталь: | Cutter screw |
| Парткод: | M400281 |
| Деталь: | Paper width sensor cable assy. |
| Парткод: | E106833 |
| Деталь: | Jam sensor plate R |
| Парткод: | M514488 |
| Деталь: | Jam sensor spring 200 |
| Парткод: | M801449 |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | MP-OJ-6505-N2 |
| Деталь: | Head lock screw 200 |
| Парткод: | M602829 |
| Деталь: | Circulation solenoid BKT |
| Парткод: | M514998 |
| Деталь: | Liquid solenoid assy. |
| Парткод: | MP-E106807 |
| Деталь: | Tube, Supply, f2 |
| Парткод: | MP-1080249 |
| Деталь: | Lure fitting |
| Парткод: | FTLL420-1 |
| Деталь: | Lure fitting |
| Парткод: | MTLL430-1 |
| Деталь: | Fluorine tube special (03x05) |
| Парткод: | MP-HSJPE3-MMK35 |
| Деталь: | Lure fitting |
| Парткод: | FTLL-430-1 |
| Деталь: | Top fan assy. |
| Парткод: | E106963 |
| Деталь: | Jam sensor plate L |
| Парткод: | M514487 |
| Деталь: | Jam sensor BKT L |
| Парткод: | M514485 |
| Деталь: | Carriage valve cable assy. |
| Парткод: | E106835 |
| Деталь: | Carriage fan sensor cable assy. |
| Парткод: | E106836 |
| Деталь: | HDC power supply jumper assy. |
| Парткод: | E106837 |
| Деталь: | P platen 160 LX |
| Парткод: | M301232 |
| Деталь: | P platen 130 LX |
| Парткод: | M301234 |
| Деталь: | Media plate 200 R |
| Парткод: | M514498 |
| Деталь: | Media holder guide 33 |
| Парткод: | M400348 |
| Деталь: | Heater holder plate 160 |
| Парткод: | M514500 |
| Деталь: | Heater holder plate 130 |
| Парткод: | M514814 |
| Деталь: | Heater holder plate 160 |
| Парткод: | M514692 |
| Деталь: | Heater holder plate 130 |
| Парткод: | M514815 |
| Деталь: | Platen thermistor P assy. |
| Парткод: | E300555 |
| Деталь: | Locking edge saddle |
| Парткод: | MM-000902 |
| Деталь: | Code type heater P160 assy. |
| Парткод: | E300866 |
| Деталь: | Code type heater P130 assy. |
| Парткод: | E300870 |
| Деталь: | Media plate 200 L |
| Парткод: | M514499 |
| Деталь: | Heat insulator A |
| Парткод: | M801556 |
| Деталь: | Heat insulator A 130 |
| Парткод: | M801562 |
| Деталь: | Heat insulator adsorption |
| Парткод: | M801559 |
| Деталь: | Heat insulator B |
| Парткод: | M801557 |
| Деталь: | Heat insulator adsorption end |
| Парткод: | M801560 |
| Деталь: | Heat insulator adsorption end 130 |
| Парткод: | M801561 |
| Деталь: | PHOTO SENSOR |
| Парткод: | MP-PS-R11L-B |
| Деталь: | P sensor angle R |
| Парткод: | M514685 |
| Деталь: | Platen frame shield plate 160 |
| Парткод: | M514489 |
| Деталь: | Platen frame shield plate 130 |
| Парткод: | M514813 |
| Деталь: | Adsorption pad 200 |
| Парткод: | M908651 |
| Деталь: | Platen flame 200 130 |
| Парткод: | M514725 |
| Деталь: | Platen flame 200 160 |
| Парткод: | M514804 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000037 |
| Деталь: | Back exhaust duct |
| Парткод: | M602867 |
| Деталь: | Adsorption fan junction cable 160 assy. |
| Парткод: | E106819 |
| Деталь: | Adsorption fan junction cable 130 assy. |
| Парткод: | E106844 |
| Деталь: | Adsorption fan assy. |
| Парткод: | E300482 |
| Деталь: | JV33 take-up right (S) assy. |
| Парткод: | MP-M007478 |
| Деталь: | Roll holder |
| Парткод: | M600500 |
| Деталь: | BEARING |
| Парткод: | 6806ZZNR |
| Деталь: | Roll base 2 (BR) |
| Парткод: | M601185 |
| Деталь: | Take-up cover (S) |
| Парткод: | M601265 |
| Деталь: | TL gear |
| Парткод: | M203683 |
| Деталь: | BEARING |
| Парткод: | 6901ZZNR |
| Деталь: | TL shaft S bracket (S) |
| Парткод: | M504102 |
| Деталь: | TL shaft S |
| Парткод: | M203685 |
| Деталь: | Extension bushing 38 |
| Парткод: | M601190 |
| Деталь: | Brushless motor SK |
| Парткод: | E300409 |
| Деталь: | Motor cable SK assy. |
| Парткод: | E103232 |
| Деталь: | Take-up motor PCB SK assy. |
| Парткод: | E300413 |
| Деталь: | Take-up motor cable assy. |
| Парткод: | E104915 |
| Деталь: | M gear bracket base (S) |
| Парткод: | M504104 |
| Деталь: | M gear bracket (S)-SI |
| Парткод: | M505965 |
| Деталь: | M gear(S) |
| Парткод: | M400235 |
| Деталь: | BEARING |
| Парткод: | BLKF0011 |
| Деталь: | M gear shaft (S)-Si |
| Парткод: | M204627 |
| Деталь: | M motor bracket (S)-Si |
| Парткод: | M505966 |
| Деталь: | Take-up motor switch SK assy. |
| Парткод: | E103224 |
| Деталь: | P holder 200 |
| Парткод: | M514702 |
| Деталь: | Clamp bushing |
| Парткод: | M600694 |
| Деталь: | Main cam |
| Парткод: | M600663 |
| Деталь: | Clamp base (P) |
| Парткод: | M400337 |
| Деталь: | Clamp spring |
| Парткод: | M800979 |
| Деталь: | Pinch roller (EPDM) |
| Парткод: | M700322 |
| Деталь: | PR shaft (P) |
| Парткод: | M205618 |
| Деталь: | CLB assy. L |
| Парткод: | M508809 |
| Деталь: | Clamp shaft JV33-160 |
| Парткод: | M205631 |
| Деталь: | Clamp shaft JV33-130 |
| Парткод: | M205677 |
| Деталь: | Clamp link spring |
| Парткод: | M800980 |
| Деталь: | Clamp bracket L |
| Парткод: | M508808 |
| Деталь: | Clamp lever |
| Парткод: | M514706 |
| Деталь: | Clamp lever |
| Парткод: | M602250 |
| Деталь: | Flange bush |
| Парткод: | 80F-0603 |
| Деталь: | Roll stopper arm cover |
| Парткод: | M602116 |
| Деталь: | Roll stopper arm 200 |
| Парткод: | M514705 |
| Деталь: | CL link LX |
| Парткод: | M514704 |
| Деталь: | Flange bush |
| Парткод: | 80F-1006 |
| Деталь: | Clamp link block |
| Парткод: | M400351 |
| Деталь: | Clamp lever F200 |
| Парткод: | M514703 |
| Деталь: | Cover SW BKT L |
| Парткод: | M514750 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000033 |
| Деталь: | MICRO SWITCH |
| Парткод: | MP-D3M-01K1-3 |
| Деталь: | Switch cover |
| Парткод: | M602228 |
| Деталь: | Cover sensor L cable assy. |
| Парткод: | E106842 |
| Деталь: | Cover sensor junction cable assy. |
| Парткод: | E106950 |
| Деталь: | One touch bushing |
| Парткод: | MM-001162 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000039 |
| Деталь: | Cartridge flame Lx3 |
| Парткод: | M514981 |
| Деталь: | Cartridge flame Lx2 |
| Парткод: | M514745 |
| Деталь: | Heater PCB assy. |
| Парткод: | MP-M012349 |
| Деталь: | P side plate L |
| Парткод: | M514490 |
| Деталь: | Y bar block |
| Парткод: | M400350 |
| Деталь: | Carriage fan assy. |
| Парткод: | E106806 |
| Деталь: | Heater PCB fan junction cable assy. |
| Парткод: | E107210 |
| Деталь: | Cartridge flame LX 1 |
| Парткод: | M514746 |
| Деталь: | One touch bushing |
| Парткод: | MM-000675 |
| Деталь: | X drive side plate |
| Парткод: | M514743 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000037 |
| Деталь: | Front cover flame L |
| Парткод: | M514748 |
| Деталь: | MAGNET CATCH |
| Парткод: | TL-295-2 |
| Деталь: | Outside heater cable assy. |
| Парткод: | E106964 |
| Деталь: | Voltage switch junction cable assy. |
| Парткод: | E106951 |
| Деталь: | AC switch cable 160 assy. |
| Парткод: | E106810 |
| Деталь: | AC switch cable 130 assy. |
| Парткод: | E106849 |
| Деталь: | P side plate ADL |
| Парткод: | M514491 |
| Деталь: | P center unglue 1LX |
| Парткод: | M514493 |
| Деталь: | Lock edge saddle |
| Парткод: | MM-001270 |
| Деталь: | P center unglue 2LX |
| Парткод: | M514492 |
| Деталь: | Main flame 160 |
| Парткод: | M514502 |
| Деталь: | Main flame 130 |
| Парткод: | M514802 |
| Деталь: | Ink supply PCB wiring cover |
| Парткод: | M514988 |
| Деталь: | One touch bushing |
| Парткод: | MM-000675 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000033 |
| Деталь: | Tube, Supply, f2 |
| Парткод: | MP-1080249 |
| Деталь: | Lure fitting |
| Парткод: | FTLL420-1 |
| Деталь: | Lure fitting |
| Парткод: | MTLL430-1 |
| Деталь: | Fluorine tube special (03x05) |
| Парткод: | MP-HSJPE3-MMK35 |
| Деталь: | Liquid solenoid assy. |
| Парткод: | MP-E106807 |
| Деталь: | Flat cable clamp |
| Парткод: | MM-000049 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000037 |
| Деталь: | Ink supply PCB assy. |
| Парткод: | MP-E106740 |
| Деталь: | Ink supply PCB BKT |
| Парткод: | M514756 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000039 |
| Деталь: | Cascade short 12 assy. |
| Парткод: | E106953 |
| Деталь: | FFC |
| Парткод: | E300886 |
| Деталь: | FFC |
| Парткод: | E300891 |
| Деталь: | A-fan junction cable assy. |
| Парткод: | E106823 |
| Деталь: | A-fan junction cable 130 assy. |
| Парткод: | E106971 |
| Деталь: | Motor all assy. 1 |
| Парткод: | M011578 |
| Деталь: | Pump motor assy. |
| Парткод: | M011572 |
| Деталь: | Stepping motor |
| Парткод: | MP-E300495 |
| Деталь: | Pump motor gear |
| Парткод: | M400210 |
| Деталь: | Motor sheet metal |
| Парткод: | M514914 |
| Деталь: | Pump middle slow down |
| Парткод: | M602804 |
| Деталь: | Tube pump 1 assy. |
| Парткод: | MP-M011571 |
| Деталь: | Pump sheet metal |
| Парткод: | M514913 |
| Деталь: | Oil less 80 flange bush |
| Парткод: | MM-001339 |
| Деталь: | PUMP GEAR |
| Парткод: | M602844 |
| Деталь: | Pump roller 09 |
| Парткод: | M207290 |
| Деталь: | L rubber |
| Парткод: | M700637 |
| Деталь: | TUBE |
| Парткод: | 3x5-TP-S |
| Деталь: | Lure fitting |
| Парткод: | MLRL013-6 |
| Деталь: | Lock ring (black) |
| Парткод: | FSLLR-2 |
| Деталь: | Lure fitting |
| Парткод: | FTLL013-6 |
| Деталь: | Pump base |
| Парткод: | M602554 |
| Деталь: | ST pump BKT |
| Парткод: | M514992 |
| Деталь: | Lure fitting |
| Парткод: | VRF206 |
| Деталь: | TUBE |
| Парткод: | 2x4-TP-SX |
| Деталь: | Lure fitting |
| Парткод: | VRM206 |
| Деталь: | Waste ink bottle 2L |
| Парткод: | SPA-0117 |
Коды ошибок
000
04
104
108
10e
10f
110
120
122
123
124
125
126
127
128
129
12e
130
146
147
151
152
153
154
155
156
157
158
15d
15f
160
161
16e
171
172
17e
181
185
186
187
188
189
201
202
203
303
304
305
401
402
403
404
406
40b
502
505
509
50a
50c
50f
516
617
618
61a
61b
627
702
707
801
802
803
804
805
806
807
808
809
80a
80b
80c
80d
80e
80f
810
811
812
813
814
815
816
817
818
819
81a
81b
829
902
909
90d
90f
910
911
na01
na02
na03
na04
na05
na06
na07
na08
na09
na10
na11
na12
na13
na14
na15
na16
na17
na18
na19
na20
na21
na22
Описание
| Error code: | 000 |
| Display: | SYSTEM HALT (*) 000 : UNNOWN ERR |
| Description: | Cover Open |
| Causes: | The front or top cover is open. |
| Remedy: | 1. Close the front or top cover. 2. Replace the interlock switches or actuator mechanism. |
| Error code: | 04 |
| Display: | ERROR CONDITION PAPER OUT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded. |
| Remedy: | Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration. |
| Error code: | 104 |
| Display: | Service Call 104: Error |
| Description: | Developer Motor Failure The Developer Motor rotation signal indicates that the motor is no longer operational. |
| Causes: | • Developer Drive Assembly, PL8.1.1 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11 • FAN/PHD/MOT Harness, PL10.1.9 |
| Remedy: | 1 Check the Developer Drive Assembly for damage. Are any parts of the Developer Drive Assembly damaged or excessively worn? Replace the Developer Drive Assy. Go to Step 2. 2 Check the Developer Motor connection. Is P/J491 connected to the harness? Go to Step 3. Reconnect the Developer Motor. 3 Test the Developer Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Developer Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Developer Motor. Is the +24 V across P/J491-1 <=> P/J 481-5? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J491. 2. Check continuity between J48 <=> J491. Replace the Engine Control Board. Replace the FAN/PHD/MOT Harness. |
| Error code: | 108 |
| Display: | Service Call 108:Error |
| Description: | Printhead Error |
| Remedy: | Yellow printhead lost Hsync Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J7 and J8 on the system board. Go to “System board” If the cables are connected correctly to the system board and to the printhead assembly, replace the “Printhead diagnostics”. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” |
| Error code: | 10e |
| Display: | SYSTEM HALT (*) 10e :FROM CLEAR |
| Description: | F-ROM CLEAR error (F-ROM clear unable) F-ROM is not clearable on Parameter writing, FW down loading and Log clearing. (fls_secclr) |
| Remedy: | 1. Execute the memory check (F-ROM) of [#TEST]. 2. Upload the parameter and initialize all parameters with [#PARAMETER]. 3. Replace the Main PCB with a new one. |
| Error code: | 10f |
| Display: | SYSTEM HALT (*) 10f : FROM WRITE |
| Description: | FROM WRITE error (F-ROM writing unable) F-ROM is not clearable on Parameter writing, FW down loading and Log clearing. (fls_secclr) |
| Remedy: | 1. Execute the memory check (F-ROM) of [#TEST]. 2. Upload the parameter and initialize all parameters with [#PARAMETER]. 3. Replace the Main PCB with a new one. |
| Error code: | 110 |
| Display: | SVC 110 ERROR |
| Description: | Printhead Error |
| Causes: | Incorrect color DTM installation, incorrect PCU installation, development bias error, MCU, LD control malfunction, loss of synchronization |
| Remedy: | No first Hysnc - cyan Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J8 and J9 on the system board. Go to “System board” on page 5-8. If the cables are connected correctly to the system board and to the printhead assembly, replace the “Printhead diagnostics”. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 122 |
| Display: | Service Call 122: Error |
| Description: | Finisher Decurler Failure, Code 122 The level of the Decurler Cam Home Sensor did not change 4 seconds after the Decurler Cam Clutch has turned on. |
| Causes: | • Decurler Cam Clutch • Stacker Motor • Finisher Control Board |
| Remedy: | 1 1. Rotate the actuator while running the Decurler Cam Position test in diagnostics. 2. Does the value change between H and L? Go to step 2. Troubleshoot using the transmissive sensor procedure. 2 Does the decurler cam clutch operate in diagnostics? Check for a mechanical problem with the decurler cam clutch drive. If no problem is found replace the clutch. Go to step 3. 3 Is +24 VDC present at P/J 849-1? Replace the decurler cam clutch. Go to step 4. 4 Is +24 VDC present at test point 5 on the finisher control board? Replace the finisher control board. Troubleshoot the +24 VDC interlock circuit. 5 Is +24 VDC present at P/J 847-11 with the Finisher Stacker Motor Down test running in diagnostics? Replace the stacker motor. Replace the finisher control board |
| Error code: | 123 |
| Display: | Service Call 123: Error |
| Description: | Finisher Set Clamp Failure, Code 123 The set clamp home sensor did not turn on within 2 seconds after the set clamp started operation. |
| Causes: | • Set Clamp Solenoid • Finisher Control Board |
| Remedy: | 1 1. Check the Set Clamp home sensor in diagnostics. 2. Does the value change from H to L while rotating the actuator? Go to step 2. Use the transmissive Sensor procedure to diagnose and repair the sensor. 2 Does the solenoid energize when running the Set Clamp Paddle test in diagnostics? Go to step 3. Go to step 4. 3 1. Run the Eject Forward Test and then the Eject Release Test in diagnostics. 2. Does the set clamp paddle turn once? Replace the finisher control board. Go to step 4. 4 Is +24 VDC present at P848A-10? Go to step 5. Go to step 6. 5 Is +24 VDC present at P848A-11? Replace the finisher control board. Replace the set clamp solenoid. 6 Is +24 VDC present at test point 9 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. |
| Error code: | 124 |
| Display: | Service Call 124: Error |
| Description: | Finisher Communication Failure, Code 124 |
| Remedy: | There are no diagnostic routines for problems involving serial communications. It is recommended that you address the following assemblies in this order: • Finisher Control Board • Engine Control Board • Perform continuity checks on any wiring harnesses involved. |
| Error code: | 125 |
| Display: | Service Call 125: Error |
| Description: | Finisher Staple Mode Logic Failure, Code 125 |
| Remedy: | There are no diagnostic routines for problems involving serial communications. It is recommended that you address the following assemblies in this order: • Stapler Assembly • Engine Control Board • Perform continuity checks on any wiring harnesses involved. |
| Error code: | 126 |
| Display: | Turn power OFF and wait 126: Dew error |
| Description: | Fuser Error |
| Causes: | Sensor dew error detected. |
| Remedy: | Fuser open thermistor hot roll |
| Error code: | 127 |
| Display: | Contact the Service center. 127: Error |
| Description: | Fuser Error |
| Causes: | • Scanner motor defective (motor lead connected incorrectly) • MCU board defective (scanner motor control unit) |
| Remedy: | Fuser open thermistor BUR |
| Error code: | 128 |
| Display: | Service Call 128: Error |
| Description: | Fuser Error |
| Causes: | • Scanner motor defective • Overload on scanner mechanism • PSU-Eb board defective • MCU board defective (scanner motor control unit) |
| Remedy: | Fuser under temperature in standby - hot roll |
| Error code: | 129 |
| Display: | ERROR 129 BATTERY EXCHANGE |
| Description: | Fuser Error |
| Causes: | • Scanner motor defective • Scanner drive mechanism defective • PSU-Eb board defective • MCU board defective (scanner motor control unit) |
| Remedy: | Fuser under temperature in standby - BUR |
| Error code: | 12e |
| Display: | ERROR 12e Head Faild[xxxx] (The details of [xxxx] are explained below this list.) |
| Description: | Abnormality of the Print head. Abnormality of the Driver of the Print head. |
| Remedy: | 1. Update F/W. 2. Initialize a parameter. 3. Disconnect and connect the FFC located between the Slider PCB and the SL-Relay PCB. 4. Replace the FFC located between the Slider PCB and the SL-Relay PCB. 5. Replace the Print Head with a new one. 6. Replace the Slider PCB with a new one. 7. Replace the SL-Relay PCB with a new one. |
| Error code: | 130 |
| Display: | Service Call 130: Error |
| Description: | Fuser Error |
| Causes: | 1) Is error message displayed? 2) Does error reoccur? |
| Remedy: | Fuser failed to reach standby temperature - hot roll |
| Error code: | 146 |
| Display: | ERROR 146 E-LOG SEQ |
| Description: | Motor |
| Remedy: | Autocompensator motor over speed, autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24 If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 147 |
| Display: | Service Call 147:Error |
| Description: | Motor |
| Remedy: | There is no autocompensator DC motor feedback. Replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 151 |
| Display: | ERROR 151 POSI.PRS KEEP OVER |
| Description: | Dusty Density Sensor The printer detects an accumulation of dust on the CTD (ADC) Sensor. |
| Causes: | • CTD (ADC) Sensor, PL5.2.19 • FSR/ADC Harness, PL5.2.28 |
| Remedy: | 1 Clean the CTD (ADC) Sensor. Does the error persist? Go to Step 2. Complete 2 Check the following for evidence of fault or damage: • Transfer Roller Assembly, PL5.1.4 • CTD (ADC) Sensor, PL5.2.19 Replace the damaged parts. Go to Step 3. 3 Check the CTD (ADC) Sensor connection. Is P/J136 connected to the harness? Go to Step 4. Reconnect the sensor. 4 Replace the CTD (ADC) Sensor. Does the error persist? Go to Step 5. Complete. 5 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J136. 2. Check continuity between J36 <=> J136. Go to Step 6. Replace the FSR/ ADC Harness. 6 Check the CTD (ADC) Sensor signal. Disconnect P/J136. Does P136-4 <=> P136-1 = 0 V? Replace the CTD (ADC) Sensor. Replace the Engine Control Board. |
| Error code: | 152 |
| Display: | ERROR 152 Main PCB V2R5 |
| Description: | Jam at Fuser: Jam F Paper did not reach the Exit Sensor on time or the Exit Sensor indicates that paper remains in the Fuser Exit Roller. |
| Causes: | • Fuser, PL5.1.1 • Exit Sensor Actuator, PL5.1.2 • Fuser Drive Assembly, PL5.2.25 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Exit Actuator and Sensor, PL5.1.2 and PL5.1.3 • Fuser Assembly, PL5.1.1 • Front Cover, PL1.1.6 • Chute Assembly In, PL5.2.1 • Transfer Roller, PL5.1.4 • Imaging Unit, PL6.1.1 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Remove the Fuser and check for broken or bent pins. Replace the parts concerned. Go to Step 3. 3 Reinstall the Fuser. Does error recur after the Fuser Assembly has been replaced? Go to Step 4. Complete 4 Test the Exit Sensor. Run the Service Diagnostics Exit Sensor Test. Does the sensor function correctly? Go to Step 7. Go to Step 5. 5 Check the Exit Sensor Signal. Insert a sheet of paper into the Fuser. Is the voltage across J361-A5 <=> J361- A6 0 V? Go to Step 7. Go to Step 6. 6 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J361 and P/J36. 2. Check continuity between J361<=>J36. Go to Step 7. Replace the FSR/ ADC Harness. 7 If possible print one sheet of paper. Does the Fuser Motor Turn? Inspect and replace defective gear(s). Go to Step 8. 8 Test the Fuser Drive Assembly. Run the Service Diagnostics Fuser Motor test. Does the Fuser Motor function correctly? Replace the Engine Control Board. Go to Step 10. 9 Check for +24 V to the Fuser Motor. Disconnect P/J521. Is there +24 V across J521-10 <=> ground? Go to Step 11. Replace the Engine Control Board. 10 Replace the Fuser Drive Assembly. Does the Fuser Motor function correctly? Complete Go to Step 11. 11 Check TNRFULL/FSR Harness continuity. 1. Disconnect P/J52 and P/J521. 2. Check continuity between J52 <=> J521. Replace the Engine Control Board. Replace the TNRFULL/FSR Harness. |
| Error code: | 153 |
| Display: | Service call 153: Error |
| Description: | Jam at Duplex: Jam D The Duplex Jam Sensor indicates that paper did not reach the sensor on time or that paper remains in the Chute Assembly Out. |
| Causes: | • Duplex Jam Sensor, PL5.4.1 • Jam Sensor Actuator, PL5.4.13 • Duplex Motor Assembly, PL5.4.5 • FRONT/DUP Harness, PL5.3.28 • Chute Assembly Out, PL5.3.1 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Duplex Motor Assembly, PL5.4.5 • JAM Sensor Actuator, PL5.4.13 • Chute Assembly Out, PL5.3.1 Are there any defects? Replace any damaged part. Go to Step 2. 2 Test the Duplex Jam Sensor. Run the Service Diagnostics Jam Sensor test. Does the sensor function correctly? Go to Step 7. Replace the Duplex Jam Sensor and Go to Step 3. 3 Check printer function. Does the printer function correctly after replacing the Duplex Jam Sensor? Complete Go to Step 4. 4 Check the Duplex Jam Sensor signal. Block the Duplex Jam Sensor. Is the voltage across J133-1 <=> J133-2 0 V? Go to Step 6. Go to Step 5. 5 Check FRONT/DUP Harness continuity. 1. Disconnect P/J133 and P/J13. 2. Check continuity between J133 <=> J13 Go to Step 6. Replace the FRONT/DUP Harness. 6 Print a Test Print in Duplex mode Does the sheet reverse in the printer? Replace the Chute Assembly Out. Go to Step 7. 7 Test the Duplex Motor. 1. Close the Interlock Switch during the test. 2. Run the Service Diagnostics Duplex Motor test. Does the Duplex Motor function correctly? Replace the Chute Assembly Out. Go to Step 8. 8 Check for +24 V to the Duplex Motor. Disconnect P/J501. Is there +24 V across P501-6 <=> ground? Go to Step 9. Replace the Engine Control Board. 9 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J501. 2. Check continuity between J13 <=> P501. Got to Step 10. Replace the FRONT/DUP Harness. 10 Replace the Duplex Motor. Does the error persist? Replace the Engine Control Board. Complete |
| Error code: | 154 |
| Display: | Service Call 154: Error |
| Description: | Jam at Registration Roller: Jam RR The Registration Sensor indicates that paper did not reach the sensor on time or that paper remains in the Registration Chute. |
| Causes: | • Registration Sensor, PL4.1.3 • Registration Sensor Actuator, PL4.1.1 • Registration Roller Assembly, PL4.2.1 |
| Remedy: | 1 Check the following for damage. • Registration Sensor Actuator, PL4.1.1 • Registration Roller Assembly, PL4.2.1 Is there any damage? Clean or replace as needed. Go to Step 2. 2 Test the Registration Sensor. Run the Service Diagnostics Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 3. 3 Check the Registration Sensor connection. Is the Registration Sensor connected to the harness? Go to Step 4. Reconnect. 4 Check all pins on the REGISNS Harness PL 4.1.4 for continuity. 1. Disconnect P/J181 and P/J18. 2. Check continuity between J181 <=> J18. Go to Step 5. Replace the Registration Sensor Harness. 5 Check the Registration Sensor signal. Block the Registration Sensor. Verify the voltage between P/J18-3 <=> P/J18-2 on the Engine Control Board is 0 VDC. Go to Step 6. Replace the Registration Sensor. 6 Test the Registration Clutch. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Registration Clutch test. Does the clutch function correctly? Go to Step 8. Go to Step 7. 7 Check the Registration Clutch resistance. Disconnect connector P/J192. Is the resistance between J192-1 <=> J192-2 less than 200ƒ¶? Go to Step 8. Replace the Registration Clutch (Part of the Registration Roller Assembly) 8 Check for +24 V to the Registration Clutch. 1. Disconnect P/J192. 2. Close the Interlock Switch while testing. Is there +24 V across P192-3 <=> ground? Replace the Registration Chute. Replace the Engine Control Board. |
| Error code: | 155 |
| Display: | Service Call 155: Error |
| Description: | Misfeed at Tray 1 (MPT): Jam T1 Paper fed from Tray 1 (MPT) did not reach the Registration Sensor on time. |
| Causes: | • Feed Roller Assembly MPT, PL5.3.20 • Interlock Switch, PL9.1.11 • Registration Sensor, PL4.1.3 • Feed Solenoid, PL5.3.9 • Registration Roller Assembly, PL4.2.1 • Main Drive Assembly, PL8.1.2 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Feed Roller Assembly MPT, PL5.3.20 • Tray 1 (MPT) • Registration Sensor, PL4.1.3 • Main Drive Assembly, PL8.1.2 Remove any foreign objects or paper debris from the paper path. Is there any damage? Replace any damaged or excessively worn parts. Go to Step 2. 2 Test the Registration Sensor. Run the Service Diagnostics Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 3. 3 Check the Registration Sensor connection. Is the Registration Sensor connected to the harness? Go to Step 4. Connect the sensor. 4 Check all pins of the REGISNR Harness PL4.1.4 for continuity. 1. Disconnect P/J181 and P/J18. 2. Check continuity between J181 <=> J18. Go to Step 5. Replace the Registration Sensor Harness. 5 Check the Registration Sensor signal. Block the Registration Sensor. Verify the voltage between P/J18-3 <=> P/J18-2 on the Engine Control Board is 0 VDC. Replace Registration Sensor. Go to Step 6. 6 If possible, print a Test Print from Tray 1 (MPT). Does the Main Motor function properly? Go to Step 16 Go to Step 7 7 Test the Main Drive Assembly. Run the Service Diagnostics Main Motor test. Does the Main Motor turn? Replace the Engine Control Board. Go to Step 8. 8 Check for +24 V to the Main Drive Motor 1. Disconnect P/J481. 2. Close the Interlock Switch while testing. Is there +24 V across J481-10 <=> J481-8? Go to Step 12. Go to Step 9. 9 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the Interlock Switch function correctly? Go to Step 11. Go to Step 10. 10 Check for +5 V to the Interlock Switch Disconnect P/J161. Is there +5 V across P161-1 <=> P161-2? Replace the LVPS. Replace the Interlock Switch. 11 Check FAN/PHD/MOT Harness continuity. 1. Disconnect P/J48 and P/J481. 2. Check continuity between J48 <=> J481 Replace Main Drive Motor Replace FAN/ PHD/MOT Harness. 12 Check Turn Roller function. 1. Perform Steps 1 ~ 3 on. 2. Open and close the front door. 3. Observe the Turn Roller. Does the Turn Roller turn while the machine is warming up? Go to Step 16. Go to Step 13. 13 Test the Turn Clutch. 1. Run the Service Diagnostics Tray 1 (MPT) Turn Clutch test. 2. Close the Interlock Switch while testing. Does the Turn Clutch function normally? Check that the Clutch doesn’t slip. Check the gears for damage. Go to Step 14. 14 Check for +24 V to the Turn Clutch. 1. Disconnect P/J191. 2. Close the Interlock Switch while testing. Is there +24 V across P191-2 <=> ground? Go to Step 15. Replace the Engine Control Board. 15 Check Turn Clutch resistance. Disconnect P/J191. Is the resistance between J191-1 <=> J191-2 less than 200Ω? Go to Step 16. Replace the Turn Clutch (Part of the Registration Roller Assembly). 16 If possible, print a Test print from Tray 1 (MPT). Check the Feed Gear operation. Does the gear function normally? Check for damage or obstructions in the paper path. Go to Step 17. 17 Test the Feed Solenoid. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Tray 1 (MPT) Feed Solenoid test. Does the Feed Solenoid function normally? Check that the Feed Solenoid spring and stopper disengage correctly. Go to Step 18. 18 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J132 and P/J13. 2. Check continuity between J13 <=> P132. Go to Step 19. Replace the FRONT/DUP Harness Assembly. 19 Check Feed Solenoid resistance. Disconnect connector P/J132. Is the resistance between J132-1 <=> J132-2 less than 100Ω? Replace the Engine Control Board. Replace the Feed Solenoid. |
| Error code: | 156 |
| Display: | ERROR 156 Main PCB V5B |
| Description: | Misfeed at Tray 2: Jam T2 Paper fed from Tray 2 did not reach the Registration Sensor on time. |
| Causes: | • Feed Rollers, PL3.3.18 • Interlock Switch, PL9.1.11 • Registration Sensor, PL4.1.3 • Registration Roller PL4.2.1 • Main Drive Assembly, PL8.1.2 • Tray 2 Paper Pick Assembly, PL3.3.1 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Feed Rollers, PL3.3.18 • Paper Pick Assembly, PL3.3.1 • Tray 2, PL2.1.1 • Registration Sensor, PL4.1.3 • Main Drive Assembly, PL8.1.2 Replace any damaged or excessively worn parts. Go to Step 2. 2 Test the Registration Sensor. Run the Service Diagnostics Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 3. 3 Check the Registration Sensor connection. Is the Registration Sensor connected to the harness? Go to Step 4. Connect the sensor. 4 Check all pins on the REGISNS Harness PL4.1.4 for continuity. 1. Disconnect P/J181 and P/J18. 2. Check continuity between J181 <=> J18 Go to Step 5. Replace the Registration Sensor Harness. 5 Check the Registration Sensor signal. Block the Registration Sensor. Is the voltage across P/J18-3 <=> P/J18-2 0 V? Replace Registration Sensor. Go to Step 6. 6 If possible, print a Test Print from Tray 1 (MPT). Does the Main Motor function properly? Go to Step 16. Go to Step 7. 7 Test the Main Drive Assembly. Run the Service Diagnostics Main Motor test. Does the Main Motor turn? Replace the Engine Control Board. Go to Step 8. 8 Check for +24 V to the Main Drive Motor 1. Disconnect P/J481. 2. Close the Interlock Switch while testing. Is there +24 V across J481-10 <=> J481-8? Go to Step 12. Go to Step 9. 9 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the Interlock Switch function correctly? Go to Step 11. Replace the parts concerned. 10 Check for +5 V to the Interlock Switch Disconnect P/J161. Is there +5 V across P161-1 <=> P161-2? Replace the LVPS. Replace the Interlock Switch. 11 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J481. 2. Check continuity between J48 <=> J481. Replace Main Drive Motor Replace FAN/ PHD/MOT Harness. 12 Check Turn Roller function. 1. Perform Steps 1 through 3 on. 2. Open and close the front door. 3. Observe the Turn Roller. Does the Turn Roller turn while the machine is warming up? Go to Step 16. Go to Step 13 13 Test the Turn Clutch. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Tray 1 (MPT) Turn Clutch test. Does the Turn Clutch function normally? Check that the Clutch doesn’t slip. Check the gears for damage. Go to Step 14. 14 Check for +24 V to the Turn Clutch. 1. Disconnect P/J191. 2. Close the Interlock Switch while testing. Is there +24 V across P191-2 <=> ground? Go to Step 15. Replace the Engine Control Board. 15 Check all pins on the FRONTCLH Harness PL4.1.21 for continuity. 1. Disconnect P/J191 and P/J19. 2. Check continuity between J19 <=> P191. Go to Step 16. Replace the FRONTCLH Harness Assembly. 16 Check Turn Clutch resistance. Disconnect P/J191. Is the resistance between J191-1 <=> J191-2 less than 200Ω? Replace the Engine Control Board. Replace the Turn Clutch (Part of the Registration Roller Assembly). 17 Check the Tray 2 Feed Solenoid. If possible, print a Test print from Tray 2. Does the Feed Gear operate correctly? Replace any damaged or excessively worn parts. Go to Step 18. 18 Test the Tray 2 Feed Solenoid. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Tray 2 Feed Solenoid test. Does the Feed Solenoid function normally? Check the Solenoid Feed spring and stopper. Go to Step 19. 19 Check all pins on the FDR Harness PL3.3.22 for continuity. 1. Disconnect P/J474 and P/J47. 2. Check continuity between J47 <=> P474. Go to Step 20. Replace the FDR Harness. 20 Check Feed Solenoid resistance. Disconnect connector P/J474. Is the resistance between J474-1 <=> J474-2 less than 100Ω? Replace the Engine Control Board. Replace Tray 2 Feed Solenoid (Part of the Tray 2 Paper Pick Assembly). |
| Error code: | 157 |
| Display: | ERROR 157 Main PCB VTT |
| Description: | Misfeed at Tray 3: Jam T3 Paper being fed from either the 550-Sheet Feeder or the top tray of the 1100-Sheet Feeder did not reach the Registration Sensor on time. |
| Causes: | For 550-Sheet Feeder: • Feed Rollers, PL11.3.20 • Paper Pick Assembly, PL11.3.1 • Drive Assembly, PL11.3.15 • OPFDR Harness, PL11.3.24 • OPTFDR Board, PL11.1.10 • OPFPLG Harness, PL11.1.13 For 1100-Sheet Feeder: • Feed Rollers, PL12.4.19 • Paper Pick Assembly, PL12.4.1 • Drive Assembly, PL12.3.9 • OPFDR Harness, PL12.3.7 • OPTFDR Board, PL12.3.3 • OPFREC2 Harness, PL12.3.1 |
| Remedy: | 1 Check the printer paper path. Does paper feed correctly from Tray 2? Go to Step 2. See "Misfeed at Tray 2 Jam T2". 2 If possible, print a Test print from Tray 3. Does the Drive Assembly operate? Go to Step 9. Go to Step 3. 3 Test the Drive Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics HCF/LTA Motor test. Does the Drive Motor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check for +24 V to the Drive Motor. 1. Disconnect P/J82. 2. Close the Interlock Switch while testing. Is the voltage between P82-1 <=> ground on the OPTFDR Board +24 V? Go to Step 7. Go to Step 5. 5 Check for +24 V to the OPTFDR 1 Board. 1. Disconnect P/J83. 2. Close the Interlock Switch while testing. Is the voltage between P83-3 <=> P83-4 on the OPTFDR Board +24 V? Replace the OPTFDR Board. Go to Step 6 6 Check the Feeder Interface continuity. 1. Disconnect P/J171 or P/J172 and P/J83. 2. Check continuity between J171/2 <=> P83 Go to Step 7. Replace the OPFREC Harness. 7 Replace the Drive Assembly. Does the error persist? Go to Step 8. Complete 8 Perform Steps 1 through 3. 1. Open and close the front door. 2. Observe the Turn Roller. Does the Turn Roller turn while the printer is warming up? Go to Step 13. Go to Step 9. 9 Test the Turn Clutch. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Turn Clutch test. Does the Tray 3 Turn Clutch function correctly? Check the Clutch for slipping or the gear for damage. Go to Step 10. 10 Check for +24 V to the Turn Clutch. 1. Disconnect P/J825 2. Close the Interlock Switch while testing. Is there +24 V across P825-2 <+>ground? Go to Step 11. Replace the OPTFDR 1 Board. 11 Check all pins on the OPFDR Harness PL11.3.24 for continuity. 1. Disconnect P/J85 and P/J825. 2. Check continuity between J85 <=> P825. Go to Step 12. Replace the OPFDR Harness. 12 Check Turn Clutch resistance. Disconnect P/J825. Is the resistance between J825-1 <=> J825-2 less than 200Ω? Go to Step 13. Replace the Turn Clutch (Part of the Paper Pick Assembly). 13 Check the Feed Gear. Does the Feed Gear in the Paper Pick Assembly turn when printing a sheet of paper? Check the Feed Solenoid for damage. Go to Step 14. 14 Test the Feed Solenoid. Run the Service Diagnostics Feed Solenoid test. Does the solenoid function correctly? Check the feed solenoid stopper and replace if necessary. Go to Step 15. 15 Check for +24 V to the Feed Solenoid. 1. Disconnect P/J824 2. Close the Interlock Switch while testing. Is there +24 V across P824-2 <=>ground? Go to Step 17. Go to Step 16. 16 Check all pins on the OPFDR Harness PL11.3.24 for continuity. 1. Disconnect P/J85 and P/J824. 2. Check continuity between J85 <=> P824 Go to Step 17. Replace the OPFDR Harness. 17 Test the Feed Solenoid resistance. Disconnect P/J824. Is J824-1 <=> J824-2 less than 100Ω? Go to Step 17. Replace the Feed Solenoid (Part of the Paper Pick Assembly). 18 Check all pins on the OPFPLG Harness PL3.2.11 for continuity. 1. Disconnect P/J171 and P/J17. 2. Check continuity between P171 <=> J17. Replace the Engine Control Board. Replace the OPFPLG Harness. |
| Error code: | 158 |
| Display: | ERROR 158 Main PCB V352 |
| Description: | Misfeed at Tray 4: Jam T4 Paper being fed from the 1100-Sheet Feeder did not reach the Registration Sensor on time. |
| Causes: | • Feed Rollers, PL12.5.18 • Paper Pick Assembly, PL12.5.1 • Drive Assembly, PL12.3.9 • OPFDR Harness, PL12.3.7 • OPTFDR Board, PL12.3.3 • OPFREC2 Harness, PL12.3 |
| Remedy: | 1 Check the printer paper path. Does paper feed correctly from Tray 2? Go to Step 2. See "Misfeed at Tray 2 Jam T2". 2 If possible, print a Test print from Tray 4. Does the Drive Assembly operate? Go to Step 9. Go to Step 3. 3 Test the Drive Assembly. Run the Service Diagnostics HCF/LTA Motor test. Does the Drive Motor function correctly? Replace the Engine Control Board, page 8-107. Go to Step 4. 4 Check for +24 V to the Drive Motor. 1. Disconnect P/J82. 2. Close the Interlock Switch while testing. Is the voltage between P82-1 <=> ground on the Upper Circuit Board HCF +24 V? Go to Step 7. Go to Step 5. 5 Check for +24 V to the OPTFDR Board. 1. Disconnect P/J83. 2. Close the Interlock Switch while testing. Is the voltage between P83-3 <=> P83-4 on the Lower Feeder Circuit Board +24 V? Replace the Lower Circuit Board HCF. Go to Step 6 6 Check all pins on the OPFREC2 Harness PL12.3.1 for continuity. 1. Disconnect P/J172 and P/J83. 2. Check continuity between J172 <=> P83. Go to Step 7. Replace the OPFREC2 Harness. 7 Replace the Drive Assembly. Does the error persist? Go to Step 8. Complete 8 Perform Steps 1 through 3. Open and close the front door. Observe the Turn Roller. Does the Turn Roller turn while the printer is warming up? Go to Step 13. Go to Step 9. 9 Test the Turn Clutch. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Turn Clutch test. Does the Tray 4 Turn Clutch function correctly? Check the Clutch for slipping or the gear for damage. Go to Step 10. 10 Check for +24 V to the Turn Clutch. 1. Disconnect P/J825 2. Close the Interlock Switch while testing. Is there +24 V across P85-2 <+>ground? Go to Step 11. Replace the Circuit Board HCF. 11 Check all pins on the OPFDR2 Harness PL12.3.7 for continuity. 1. Disconnect P/J85 and P/J825. 2. Check continuity between J85 <=> P825. Go to Step 12. Replace the OPFDR2 Harness. 12 Check Turn Clutch resistance. Disconnect P/J825. Is the resistance between J825-1 <=> J825-2 less than 200Ω? Go to Step 13. Replace the Turn Clutch (Part of the Paper Pick Assembly). 13 Check the Feed Gear. Does the Feed Gear in the Paper Pick Assembly turn when printing a sheet of paper? Check the Feed Solenoid for damage. Go to Step 14. 14 Test the Feed Solenoid. Run the Service Diagnostics Feed Solenoid test. Does the solenoid function correctly? Check the feed solenoid stopper and replace if necessary. Go to Step 15. 15 Check for +24 V to the Feed Solenoid. 1. Disconnect P/J824 2. Close the Interlock Switch while testing. Is there +24 V across P824-2 <+>ground? Go to Step 17. Go to Step 16. 16 Check all pins on the OPFDR Harness PL12.3.7 for continuity. 1. Disconnect P/J85 and P/J824. 2. Check continuity between J85 <=> P824. Go to Step 17. Replace the OPFDR Harness. 17 Test the Feed Solenoid resistance. Disconnect P/J824. Is J824-1 <=> J824-2 less than 100Ω? Go to Step 17. Replace the Feed Solenoid (Part of the Paper Pick Assembly). 18 Check all pins on the OPFPLG Harness PL3.2.11 for continuity. 1. Disconnect P/J171 and P/J17. 2. Check continuity between P171 <=> J17. Replace the Engine Control Board. Replace the OPFPLG Harness. |
| Error code: | 15d |
| Display: | SYSTEM HALT (*) 15d : MAIN FPC-1 |
| Description: | 30pin FPC 1 of MAIN PCB connect error |
| Remedy: | 1. Check the connections between the HDC PCB and the MAIN PCB, and then disconnect and connect the FFCs. 2. Replace the FFCs of the above routes. 3. Replace the HDC PCB with a new one. 4. Replace the MAIN PCB with a new one. |
| Error code: | 15f |
| Display: | ERROR 15f HEAD DRIVE HOT |
| Description: | COM driver becomes the high temperature. |
| Remedy: | 1. Confirm movement of Slider Relay Cooling Fan. 2. Disconnect and connect the FFC located between the Slider PCB and the SL-Relay PCB. 3. Replace the SL-Relay PCB with a new one. 4. Replace the FFC located between the Slider PCB and the SL-Relay PCB 5. Replace the Print Head with a new one. 6. Replace the Slider PCB with a new one. |
| Error code: | 160 |
| Display: | SVC 160 ERROR |
| Description: | Tray and Media Errors When a tray is pulled out that prevents printing during a print job, an error condition exists.When a tray is pulled out while no job is printing or that does not prevent printing during a print job, a warning condition exists. |
| Causes: | • Paper Size Switch, PL3.2.5 • Paper Tray, PL2.1.1 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Tray 2 Paper Size Switch, PL3.2.5 • Tray 2 Paper Size Switch Actuators, PL2.1.10 • Paper Tray, PL2.1.1 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Test the Tray 2 Paper Size Switches. Run the Service Diagnostics Paper Size Switch test. Use the table on. Do the switches function correctly? Replace the Engine Control Board. Go to Step 3. 3 Check the Paper Size Switch signals. 1. Disconnect P/J47. 2. Verify +3.3 V on pins P/J47-1 <=> P47-3 P/J47-2 <=> P47-3 P/J47-4 <=> P47-3 Is there +3.3 V when actuated? Go to Step 4 Replace the Paper Size Switch. 4 Check all pins on the FDR Harness for continuity. 1. Disconnect P/J47 and P/J471. 2. Check continuity between J47 <=> J471. Replace the Engine Control Board. Replace the FDR Harness. |
| Error code: | 161 |
| Display: | SYSTEM HALT (*) 161 : PCB MAIN-F6 |
| Description: | IPU Error At power on, or when the machine returns from an energy save mode, the self-diagnostic program returned an IPU error. |
| Causes: | • IPU defective • Connection between SBU and IPU is loose, broken, or defective |
| Error code: | 16e |
| Display: | ERROR 16e Main PCB V3R3B |
| Description: | Main board 3.3VÇa power supply is abnormal. |
| Remedy: | 1. Replace the Main PCB with a new one. |
| Error code: | 171 |
| Display: | Inspection is required. 171:Error |
| Description: | Motor |
| Causes: | Does this error recur? |
| Remedy: | Mirror motor lock not achieved - cyan - go to “Printhead diagnostics” on page 3-1. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” on page 3-1. |
| Error code: | 172 |
| Display: | Inspection is required. 172:Error |
| Description: | Motor |
| Causes: | Does this error recur? |
| Remedy: | Mirror motor lost lock - cyan - go to “Printhead diagnostics” on page 3-1. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” on page 3-1. |
| Error code: | 17e |
| Display: | SYSTEM HALT (*) 17e : PCB IIO1 |
| Description: | No INK SYSTEM PCB An error occurred at serial communication check after configuration. |
| Remedy: | 1. Check the connections between the INK SYSTEM PCB and the Central-IO PCB and then disconnect and connect the FFC. 2. Replace the FFC of the above routes. 3. Replace the INK SYSTEM PCB with a new one. 4. Replace the Central-IO PCB with a new one. |
| Error code: | 181 |
| Display: | Inspection is required. 181:Error |
| Description: | Scanner Unit Fan Error: Lamp Regulator Fan (Right) (D016/D097 only) The MCU issued a lock signal for the lamp regulator fan (front, right). |
| Causes: | • Fan, MCU harness loose, defective • Lamp regulator (right) fan motor defective • MCU defective • SIB defective |
| Error code: | 185 |
| Display: | SYSTEM HALT (*) 185 : PCB LED |
| Description: | Exposure Lamp 1 Lamp Regulator (Right) Error (D016/D097 only) The MCU detected a defect in the lamp regulator (right) when the 1st exposure lamp lit. . |
| Causes: | • 1st exposure lamp defective • 1st lamp FFC (flat film cable) loose or defective • MCU to lamp regulator (left) harness defective • Lamp regulator (left) is defective • MCU defective • SIB defective |
| Error code: | 186 |
| Display: | ERROR 186 HDC UNDERFLOW |
| Description: | Exposure Lamp 2 Lamp Regulator (Left) Error (D016/D097 only) The MCU detected a defect in the lamp regulator (left) when the 2nd exposure lamp lit. . |
| Causes: | • 2nd exposure lamp defective • 2nd lamp FFC (flat film cable) loose or defective • MCU to lamp regulator (left) harness defective • Lamp regulator (left) is defective • MCU defective • SIB defective |
| Error code: | 187 |
| Display: | Service Call 187: Error |
| Description: | I/F Error,Loc: Control Panel (Reserved) |
| Causes: | Is cable properly connected to control panel? |
| Remedy: | Connect properly. Replace control panel and cable. |
| Error code: | 188 |
| Display: | Service Call 188: Error |
| Description: | Motor Driver Board Communications Error Applicable Status Code: Code 188: A Sub-CPU communications error with installed options. |
| Causes: | • Motor Driver Board, PL2.1.10 |
| Remedy: | 1 Check the connections to the Engine Control Board. Are DV0 and DV1 completely connected? Replace the Motor Driver Board. Connect the two ribbon cables. |
| Error code: | 189 |
| Display: | Service Call 189: Error |
| Description: | CIS gray balance adjustment error The adjustment error occurs during the test after adjusting the gray balance. |
| Causes: | • Defective CIS |
| Remedy: | 1. Retry the gray balance adjustment. 2. If the machine does not recover, do the following steps. • Turn off the machine. • Make sure CN210 and CN220 are connected firmly. • Turn on the machine. 3. If the machine does not recover, replace the CIS. |
| Error code: | 201 |
| Display: | ERROR 201 COMMAND |
| Description: | PU F/W Flash write error (Reserved) |
| Causes: | • Defective polygon motor • Defective harness |
| Remedy: | 1. Connect the cable correctly. 2. Replace the engine control board. 3. Replace the laser scanning unit. 4. Check or replace the cable. |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 303 |
| Display: | SYSTEM HALT (*) 303 : PCB MAIN ET |
| Description: | AC charge output error [Y] The measured voltage is not proper when IOB measures the charge output for each color. |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 304 |
| Display: | ERROR 304 USB INIT ERR |
| Description: | Charge AC bias error [K] The charge current less than 200 mkA is detected. |
| Causes: | Defective charge roller. Defective connectors. Disconnected harness. Defective high voltage power 1. |
| Remedy: | 1. Check the connectors. 2. Replace the PCU for black. 3. Replace the drum positioning plate. |
| Error code: | 305 |
| Display: | ERROR 305 USB TIME OUT |
| Description: | Charge Corona Wire Cleaner Error The charge wire cleaner did not: (1) come from the home position within 5 s, or (2) did return to the home position within 3.75 s due to wire cleaner overload. |
| Causes: | • Cleaner unit blocked or damaged • Until replacement parts become available, set SP2804 to "0" to disable the charge-corona cleaning function so the machine can operate. |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 403 |
| Display: | ERROR 403 X CURRENT |
| Description: | Transfer belt position sensor error The transfer belt position sensor did not activate after the transfer belt contact clutch was switched on twice and rotated once. |
| Causes: | • Main motor malfunction • Transfer belt contact clutch defective • Transfer belt position sensor harness or connector loose, broken, defective • Transfer belt position sensor defective |
| Remedy: | 1. Check if there is no error on the print data. (Check if the same error occurs on other data?) 2. Check if it moves to the X-direction smoothly in the power-off condition. 3. Make sure no torsion on the X-bar or Y-bar. 4. Check if there is no trouble on the Timing Belt. 5. Check if there is no trouble on the Motor Cable. (disconnecting, burnout, or the like) 6. Check the FFC between each PCB and Shortconnectors connected on the PCB. 7. Replace the X-axis Motor with a new one. |
| Error code: | 404 |
| Display: | ERROR 404 Y CURRENT |
| Description: | Transmitter sent NSS (or DCS) followed by TCF three times, but the receiver did not respond. (CFR or FTT is usually returned) |
| Causes: | Receiver is defective. (Modem, MJR PCB, etc.) SC PCB or MJR PCB are defective. Receiver disconnects line during first NSS (or DCS) is transmitted. |
| Remedy: | 1. Check if there is no error on the print data. (Check if the same error occurs on other data?) 2. Check if it moves to the Y-direction smoothly in the power-off condition. 3. Check if there is no trouble on the Timing Belt. 4. Check if there is no trouble on the Motor Cable. (disconnecting, burnout, or the like) 5. Check the FFC between each PCB and Shortconnectors connected on the PCB. 6. Replace the Y-axis motor with a new one. |
| Error code: | 406 |
| Display: | SYSTEM HALT (*) 406 : WIPER ORG |
| Description: | ID Sensor Pattern Edge Detection Error The ID sensor pattern check could not detect the correct voltage on the ID sensor pattern (below 2.5V) within 0.6 sec. |
| Causes: | • ID sensor dirty • ID sensor harness loose, damaged, defective • ID sensor connector defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 40b |
| Display: | SYSTEM HALT (*) 40b : UN MAGNETIC |
| Description: | DC motor is driving without excited |
| Remedy: | 1.Update F/W. 2. Upload the parameter and initialize parameter with #PARAMETER. 3. Replace the Main PCB with a new one. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 505 |
| Display: | ERROR 505 !WORK High |
| Description: | HCF must be rebuilt |
| Causes: | The 2nd tray of D580 when D579 and D580 are attached, or D631 when D580 and D631 are attached. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 509 |
| Display: | SYSTEM HALT (*) 509 : HDC POSCNT |
| Description: | Replace red developer |
| Causes: | • Poor connection or defective tray 5 or 6 lift motor • Poor connection or defective tray 5 or 6 lift sensor • Remaining paper or another obstruction has stopped the tray and motor. • Pick-up solenoid 5 or 6 connector is loose. • Pick-up solenoid 5 or 6 is blocked by an obstruction. |
| Remedy: | 1. Replace the tray 5 or 6 lift motor. 2. Replace the tray 5 or 6 lift sensor. 3. Check or clear obstacles around pick-up solenoid 5 or 6. |
| Error code: | 50a |
| Display: | ERROR 50a Y ORIGIN |
| Description: | Y-origin error (Origin of Y-axis can not be detected) |
| Remedy: | 1. Execute and confirm [#TEST]->[SENSOR TEST] - >[Y-ORG].(Confirm that the ON/OFF display is switched by moving the carriage left and right.) 2. [Execute [#TEST]->[CHECK ENCODER]. 3. Check in manual if the Head Assy. (carriage) moves left and right smoothly. 4. Check the connector connection of Y-origin Sensor and Linear Encoder. 5. Replace the Y-origin Sensor or Linear Encoder with a new one. 6. Check the assembly and connector connection of Yaxis Motor. 7. Replace the Y-axis Motor with a new one. 8. Replace the Slider PCB with a new one. 9. Replace the SL-Relay PCB with a new one. 10. Replace the Main PCB with a new one. |
| Error code: | 50c |
| Display: | ERROR 50c MEDIA WIDTH SENSOR |
| Description: | The media width could not be read correctly. |
| Remedy: | 1. Check the media setting position. 2. Perform cleaning of the media width sensor. 3. Execute [#TEST PAPER SENSOR]. |
| Error code: | 50f |
| Display: | ERROR 50f L-SCALE BLACK |
| Description: | Liner Scale error |
| Remedy: | 1. Check the assembly position of Linear Scale and Encoder PCB Assy.. 2. Check Linear Scale (scratches or dirtiness or so.) 3. Replace the Linear Scale with a new one. 4. Replace the Encoder PCB Assy. with a new one. |
| Error code: | 516 |
| Display: | ERROR 516 MEDIA SET POSITION L |
| Description: | DADF feed rollers should be replaced |
| Causes: | • Loose connection between the BCU and the duplex unit controller board |
| Remedy: | 1. Check the media setting position. 2. Perform cleaning of the media width sensor. 3. Execute [#TEST PAPER SENSOR]. |
| Error code: | 617 |
| Display: | ERROR 617 DAMPER SENSOR:12345678 |
| Description: | An error of the liquid level detection sensor of the damper has been detected. |
| Remedy: | 1. Check the connection of the liquid level detection sensor. 2. From [#TEST SENSOR] -> [DAMPER], check the detection status of the liquid level detection sensor. 3. Replace the Liquid level detection sensor. |
| Error code: | 618 |
| Display: | ERROR 618 DAMPER/HIGH:12345678 |
| Description: | Even though a certain amount of ink has been consumed, there is no change in the liquid level detection sensor “High”. |
| Remedy: | 1. Check the nozzle status. (If nozzle clogging is terrible, consumption difference may be generated.) 2. From [#TEST SENSOR], check the detection status of the liquid level detection sensor. If there is an error, replace the liquid level detection sensor. 3. Perform [MAINTENANCE DAMPER]. 4. Replace the damper. |
| Error code: | 61a |
| Display: | ERROR 61a INK OVER FLOW:12345678 |
| Description: | Overflow from the damper has been detected.(Sensor detect the damper is distend.) |
| Remedy: | 1. Perform [MAINTENANCE DAMPER]. Check that it has been discharged to the middle status. 2.With [#TEST SENSOR], check the detection status of the target sensor. 3. Replace the Liquid level detection sensor. 4. Replace the damper. 5. Check that the cartridge valve is not open. (Because ink flows into the damper due to head difference.) |
| Error code: | 61b |
| Display: | ERROR 61b SUPPLY INK:12345678 |
| Description: | Ink filling into the damper has failed. |
| Remedy: | 1.With [#TEST SENSOR], check the detection status of the target liquid level detection sensor. (Also, visually check the sensor position of the damper.) 2. From [#TEST AGEING] -> [PUMP MOTOR], discharge ink in the damper to collapse the damper. From [#TEST AGEING] -> [INK SUPPLY], check that sending ink is performed. *If sending ink cannot be performed: The supply pump, the cartridge valve and the UISS valve shall be replaced. |
| Error code: | 627 |
| Display: | ERROR 627 INSERT CARTRIDGE |
| Description: | BICU/LCT communication/break reception error During communication with the LCT, the BICU received a break (Low) signal. |
| Causes: | • Serial line connection unstable • External noise on the line |
| Error code: | 702 |
| Display: | ERROR 702 THERMISTOR |
| Description: | ADF Feed-In Motor Error (D016/D097 only) While the feed motor is operating, the encoder pulse signal is not received within the specified time, or the paper size length encoder signal cannot be detected within the specified time (the encoder is built into the feed-in motor). |
| Causes: | • Feed-in motor connector, harness loose, broken, defective • Paper length sensor connector, harness loose, broken, defective • Feed-in motor defective • Paper length sensor or encoder is defective • ADF main control board defective |
| Remedy: | 1. Check the harness connections. 2. Replace the feed-in motor. 3. Replace the paper length sensor. 4. Replace the main board of the ADF. |
| Error code: | 707 |
| Display: | ERROR 707 !HD HEATER BRK |
| Description: | Is the heater of the head disconnected? (The temperature does not rise after heating for over a certain period of time.) |
| Remedy: | 1. Check the room temperature is not too low. 2. Replace the Print Head with a new one. 3. Replace the Slider PCB with a new one. |
| Error code: | 801 |
| Display: | SYSTEM HALT (*) 801 : (C)OPCODE |
| Description: | Video output error (Y) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 802 |
| Display: | SYSTEM HALT (*) 802 : (C)SLOT |
| Description: | Video output error (M) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 803 |
| Display: | SYSTEM HALT (*) 803 : (C)CPU ADDR |
| Description: | Video output error (C) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 804 |
| Display: | SYSTEM HALT (*) 804 : (C)DMA ADDR |
| Description: | Startup without video input end (K) A video transmission was requested from the scanner, but the scanner did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 805 |
| Display: | SYSTEM HALT (*) 805 : (C)ZERO DIV |
| Description: | Startup without video input end error (Y) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 806 |
| Display: | SYSTEM HALT (*) 806 : FW/SIO bit |
| Description: | Startup without video input end error (M) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 807 |
| Display: | SYSTEM HALT (*) 807 : FW/SIO wbsy |
| Description: | Startup without video input end error (C) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 808 |
| Display: | SYSTEM HALT (*) 808 : FW/STP-MTR |
| Description: | Startup without video input end error (R) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 809 |
| Display: | SYSTEM HALT (*) 809 : FW/XY param |
| Description: | Startup without video input end error (G) Video transfer to the engine is started, but a video transmission end command is not issued by the engine within the specified time. |
| Causes: | • Defective controller board |
| Error code: | 80a |
| Display: | SYSTEM HALT (*) 80a : FW/Y RANGE |
| Description: | FW error (Y movable range error) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 80b |
| Display: | SYSTEM HALT (*) 80b : FW/ctrltsk |
| Description: | FW error (Motor control task error) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 80c |
| Display: | SYSTEM HALT (*) 80c : FW/PUMP W |
| Description: | FW error (Suction Pump stop waiting time over at capping) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 80d |
| Display: | SYSTEM HALT (*) 80d : FW/SERVO IT |
| Description: | FW error (Servo interruption error) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 80e |
| Display: | SYSTEM HALT (*) 80e : FW/FROM prm |
| Description: | FW error (FROM PARAM error (F/W BUG)) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 80f |
| Display: | SYSTEM HALT (*) 80f : FW/SIO vch FW error (Virtual serial CH setting error) |
| Description: | FW error (Virtual serial CH setting error) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 810 |
| Display: | SYSTEM HALT (*) 810 : FW/KEY RDI |
| Description: | Startup without video input end error (B) Video transfer to the engine is started, but a video transmission end command is not issued by the engine within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 811 |
| Display: | SYSTEM HALT (*) 811 : FW/SIO read |
| Description: | FW error (Serial control F/W error (RD BUSY)) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 812 |
| Display: | SYSTEM HALT (*) 812 : FW/CRTRG NO |
| Description: | FW error (Cartridge number error) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 813 |
| Display: | PRESS POWER SW FOR 5SEC Error : 813 |
| Description: | SU Communication Error |
| Causes: | Communication error between the Controller and the Scanner Unit is detected. |
| Remedy: | Turn off and on the MFP. |
| Error code: | 814 |
| Display: | PRESS POWER SW FOR 5SEC Error : 814 |
| Description: | SU FW Removed It is an error to notify that SU FW was erased by special key operation from a panel. |
| Remedy: | It is an error to notify that SU FW was erased by special key operation from a panel. |
| Error code: | 815 |
| Display: | Power OFF/ON 815:Error |
| Description: | Mailbox is full. |
| Remedy: | Cycle the power. |
| Error code: | 816 |
| Display: | SYSTEM HALT (*) 816 : FW/FROM WRC |
| Description: | Energy saving I/O sub-system error |
| Causes: | The energy saving I/O sub-system detects an error. • Defective energy saving I/O sub-system • The energy saving I/O sub-system detects a controller board error (No response) |
| Remedy: | • Turn the main power switch off and on. • Replace the controller board. |
| Error code: | 817 |
| Display: | SYSTEM HALT (*) 817 : FW/SaveArea |
| Description: | Monitor error This is a file detection and electronic file signature check error when the boot loader attempts to read the self-diagnostic module, system kernel, or root system files from the OS Flash ROM, or the items on the SD card in the controller slot are false or corrupted. |
| Causes: | OS Flash ROM data defective. SD card data defective. Change the controller firmware. Use another SD card. |
| Remedy: | • Change the controller firmware. • Use another SD card. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 81a |
| Display: | SYSTEM HALT (*) 81a : FW/FROM SIZ |
| Description: | FW error (FROM size over) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 81b |
| Display: | SYSTEM HALT (*) 81b : FW/STACK OV |
| Description: | FW error (STACK OVER) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 902 |
| Display: | Power OFF/ON 902:Error |
| Description: | Engine software error |
| Causes: | These errors indicate an unrecoverable system software error. |
| Remedy: | Replace the system board. |
| Error code: | 909 |
| Display: | ERROR 909 PARAMETER VERSION |
| Description: | Parameter version which is downloaded is different from FW version. |
| Error code: | 90d |
| Display: | ERROR 90d NO HEAD SELECT |
| Description: | Loaded number of the head is assumed zero. |
| Remedy: | Check the setting of loading number of the head in the parameter. (System parameter No.41 HEAD NO=3) |
| Error code: | 90f |
| Display: | ERROR 90f |
| Description: | Lacking printing area in printing the builtin pattern. |
| Remedy: | 1. Move the Y origin. 2. Replace the media. |
| Error code: | 910 |
| Display: | SYSTEM HALT (*) 910 : DEVICE CONST |
| Description: | Tray 2 Lift Motor Failure Code 910: The Tray 2 Lift Motor is not rotating. |
| Causes: | • Tray 2 Lift Motor, PL4.1.23 • Motor Driver Board, PL2.1.10 • LVPS, PL3.1.1 |
| Remedy: | 1 Test the Lift Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Tray 2 Lift Motor test. Does the motor operate? Complete. Replace the motor. If the error persists, go to Step 2. 2 Check for +24 V to the Lift Motor. Is there +24 V across GDDC-1 <=> ground? Go to Step 5. Go to Step 3. 3 Check Motor Driver Board POW24 connector for 24 V. 1. Disconnect POW24. Is there +24 V across POW24 pins 1 and 2? Replace the Motor Driver Board. Go to Step 4. 4 Check for 24 V at the LVPS 1. Disconnect CN2 on the LVPS. Is there +24 V across pins 1 and 2? Replace the POW24 Harness. Replace the LVPS. 5 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 911 |
| Display: | ERROR 911 ENVIRONMENT TEMP(HI) |
| Description: | DC pick motor excessive PWM |
| Remedy: | • Check system board • Check autocompensator motor |
| Error code: | na01 |
| Display: | <LOCAL> INK IC CAN`T READ |
| Description: | IC chip of Ink Cartridge unreadable properly |
| Remedy: | 1. Check the attached status of the chip. 2. Perform #TEST/ Check the IC. 3.Replace the ID Contact PCB Assy. with a new one. |
| Error code: | na02 |
| Display: | <LOCAL> WRONG INK IC |
| Description: | IC chip of Ink Cartridge unreadable properly |
| Remedy: | 1. Check the attached status of the chip. 2. Perform #TEST/ Check the IC. 3.Replace the ID Contact PCB Assy. with a new one. |
| Error code: | na03 |
| Display: | <LOCAL> INK TYPE |
| Description: | Type of inserted Ink Cartridge is different. |
| Remedy: | 1. Check the type of the ink cartridge. |
| Error code: | na04 |
| Display: | <LOCAL> INK COLOR |
| Description: | The color of Ink Cartridge inserted is different from the color to be set. |
| Remedy: | 1. Check the color of the ink cartridge. |
| Error code: | na05 |
| Display: | <LOCAL> WRONG CARTRIDGE |
| Description: | An error occurred in the IC chip information of the ink cartridge. |
| Remedy: | The chip was used too much (exceeding the specified times). 1. Check whether the chip was also replaced when the pack was replaced. 2. Check the W ink nozzle clogging and resolve it. 3. Replace the chip. |
| Error code: | na06 |
| Display: | <LOCAL> NO CARTRDG |
| Description: | No cartridge (Cartridge is not installed) |
| Remedy: | (When the message is still displayed even after a Ink Cartridge is charged;) 1. Execute and confirm [#TEST SENSOR]->[INK CARTRIDGE](The number meets the cartridge No.). 2. Check the peripheral and the assembly of the Presence Sensor. 3. Check the connection of the Presence Sensor and the End Sensor 4. .Replace the Cartridge with a new one 5. Replace the Presence/Near End Sensor with a new one. 6. Replace the Ink System PCB with a new one. 7. Replace the MAIN PCB with a new one. |
| Error code: | na07 |
| Display: | <LOCAL> INK END |
| Description: | Ink end (No ink left) |
| Remedy: | (When the message is still displayed even after a new Ink Cartridge or an empty Ink Cartridge is charged;) 1. Execute and confirm [#TEST SENSOR]->[INK END](The number meets the cartridge No.). 2. Check the peripheral and the assembly of the End Sensor. 3. Check the connection of the Presence Sensor and the Near End Sensor. 4. Replace the Cartridge with a new one 5. Replace the Presence/Near End Sensor with a new one. 6. Replace the Ink System PCB with a new one. 7. Replace the MAIN PCB with a new one. |
| Error code: | na08 |
| Display: | <LOCAL> INK NEAREND |
| Description: | Ink near end (A small amount of ink left) |
| Remedy: | (When the message is still displayed even after a new Ink Cartridge or an empty Ink Cartridge is charged;) 1. Execute and confirm [#TEST SENSOR]->[INK END](The number meets the cartridge No.). 2. Check the peripheral and the assembly of the End Sensor. 3. Check the connection of the Presence Sensor and the Near End Sensor. 4. Replace the Cartridge with a new one 5. Replace the Presence/Near End Sensor with a new one. 6. Replace the Ink System PCB with a new one. 7. Replace the MAIN PCB with a new one. |
| Error code: | na09 |
| Display: | <LOCAL> CHECK INK PACK |
| Description: | Even if there is enough amount of ink, ink end was detected. |
| Remedy: | Check the ink pack setting status in the eco case. |
| Error code: | na10 |
| Display: | <LOCAL> EXPIRATION |
| Description: | Some ink cartridges are expired. |
| Remedy: | 1. 1. Check the expiration date of the ink. (If this message appears when a correct cartridge is set) 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4.Replace the Cartridge with a new one. 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the Ink System PCB with a new one. |
| Error code: | na11 |
| Display: | <LOCAL> EXPIRATION(1MONTH) |
| Description: | Some ink cartridges are expired. (One month has passed after the expiration date.) |
| Remedy: | 1. Be careful that the expiration date is coming soon. You can use up to the next month. The red LED blinks. ((If this message appears when a correct cartridge is set) 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4.Replace the Cartridge with a new one. 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the Ink System PCB with a new one. |
| Error code: | na12 |
| Display: | <LOCAL> EXPIRATION (2MONTH) |
| Description: | Some ink cartridges are expired. (Two months have passed after the expiration date.) |
| Remedy: | Replace the cartridge with the warning. |
| Error code: | na13 |
| Display: | <LOCAL> Can`t PRINT/ CART.[ENT] |
| Description: | Multiple ink errors (unusable inks) occurred. Ink supply (printing, cleaning, etc.) cannot be performed. |
| Remedy: | Press the [ENTER] key, and check the relevant cartridge and the error contents. Then replace it with a usable one. |
| Error code: | na14 |
| Display: | <LOCAL> Check waste ink[MNT] |
| Description: | The count of the waste ink tank exceeded the specified amount. |
| Remedy: | Check the waste ink tank. Press the [MAINT] key, and correct the counter or reset it. |
| Error code: | na15 |
| Display: | <LOCAL> Replace WIPER [MNT] |
| Description: | The count of the wiper exceeded the specified amount. |
| Remedy: | Press the [MAINT] key, and replace the wiper. |
| Error code: | na16 |
| Display: | <LOCAL> ** NO MEDIA ** |
| Description: | The media is not set. Or, the sensor has been broken. |
| Remedy: | 1. Set the media. 2. Check the media sensor operation/ replace it. |
| Error code: | na17 |
| Display: | <LOCAL> DATA REMAIN |
| Description: | Data has already been received. |
| Remedy: | Press the REMOTE key and perform printing. Or, perform data clear. |
| Error code: | na18 |
| Display: | <LOCAL> INK NEAR END [ENT] |
| Description: | Ink near end (A small amount of ink left) |
| Remedy: | Press the [ENTER] key and check the relevant cartridge. (Be careful that ink end is coming soon.) |
| Error code: | na19 |
| Display: | <LOCAL> SUPPLY INK :MMCCYYKK |
| Description: | Ink filling into the damper has failed. |
| Remedy: | 1. Perform [ MAINTENANCE DAMPER ]. 2. Also check the amount of remaining ink in the cartridge. |
| Error code: | na20 |
| Display: | <LOCAL> Damper Sens:MMCCYYKK |
| Description: | The liquid surface sensor abnormality of the damper has been detected. |
| Remedy: | 1. Turn OFF the power supply once, and wait for a while. And then turn ON the power supply again (when it is displayed again). Same as ERROR617. |
| Error code: | na21 |
| Display: | <LOCAL> InkOverflow:MMCCYYKK |
| Description: | Overflow from the damper has been detected. |
| Remedy: | 1. Perform [ MAINTENANCE DAMPER ] (when it is displayed again). Same as ERROR61a. |
| Error code: | na22 |
| Display: | <LOCAL> Damper HIGH:MMCCYYKK |
| Description: | Even though a certain amount of ink has been consumed, there is no change in the liquid level detection sensor “High”. |
| Remedy: | Perform [ MAINTENANCE DAMPER ] (when it is displayed again). Same as ERROR618,619. |
