Mimaki JV4-180

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

пьезоэлектрическая струйная

Макс. формат

Цветность печати

цветная

Общие характеристики
Тип устройства	Принтер
Печать фотографий
Факс
Телефон
Сканер
Копир
Макс. формат	A0
Цветность печати	цветная
Технология печати	пьезоэлектрическая струйная
Тип	струйный
Принтер
Двусторонняя печать
Печать без полей
Прямая печать
Макс, разрешение для ч/б печати
По X	1 440
По Y	1 440
Сканер
Отправка изображения по e-mail
Стандарт WIA
Стандарт TWAIN
Печать на:
CD/DVD
Фотобумаге
Пленках
Этикетках
Конвертах
Рулоне
Матовой бумаге
Карточках
Глянцевой бумаге
Факс
Цветной
Телефон
Стандарт DECT
Проводная трубка
Беспроводная трубка
АОН
Caller ID
Автоответчик
Спикерфон
Языки управления
PDF
PCL 5e
PCL 5c
PPDS
PostScript 3
PCL 6
PostScript 2
PostScript
Финишер
Электронная сортировка
Сортер
Сортировка со сдвигом
Степлер
Брошюровщик
Интерфейсы
FireWire (IEEE 1394)
Wi-Fi
USB
Ethernet (RJ-45)
Устройство для чтения карт памяти
Веб-интерфейс
RS-232
Инфракрасный порт
LPT
Bluetooth
Поддержка ОС
Linux
DOS
Mac OS
Windows
Габариты
Глубина	1 220
Ширина	3 025
Высота	730
Вес	160

Модули

WASTE INK TANK ASSY.

COVER ASSY. - 1/3

FRAME ASSY. - 2/2

ELECTRICAL UNIT ASSY. - 1/2

ROLL ASSY. (JV4-130/160)

X-DRIVE ASSY.

Y-DRIVE ASSY.

KEYBOARD ASSY.

Y-BAR ASSY.

COVER ASSY. - 3/3

CARTRIDGE ASSY.

ROLL ASSY. (JV4-180)

FRAME ASSY. - 1/2

CLAMP ASSY. - 1/2

CLAMP ASSY. - 2/2

SLIDER ASSY.

TAKE-UP DEVICE ASSY.

STATION ASSY. - 1/2

STATION ASSY. - 2/2

HEAD ASSY. - 2/2

LEG ASSY.

HEAD ASSY. - 1/2

COVER ASSY. - 2/3

ELECTRICAL UNIT ASSY. - 2/2

Детали

Деталь:	F-station
Парткод:	M601080

Деталь:	FS-bracket
Парткод:	M503460

Деталь:	Tank guide R
Парткод:	M503840

Деталь:	TUBE GUIDE
Парткод:	M600653

Деталь:	Waste ink tank guard
Парткод:	M600654

Деталь:	Waste ink tank 2L ASSY
Парткод:	M004649

Деталь:	Tank guide
Парткод:	M503459

Деталь:	Waste ink tank L
Парткод:	M601012

Деталь:	YR-cover
Парткод:	M503483

Деталь:	Right side plate
Парткод:	M503475

Деталь:	Electrical unit angle
Парткод:	M503558

Деталь:	Righr cover
Парткод:	M601021

Деталь:	Under cover R
Парткод:	M503522

Деталь:	SR-cover bracket 2
Парткод:	M503481

Деталь:	SR-cover bracket 1
Парткод:	M503480

Деталь:	Take-up device junction cable assy.
Парткод:	E102016

Деталь:	SR-cover
Парткод:	M503479

Деталь:	Cover cushion D
Парткод:	M700283

Деталь:	Front cover D catch bracket
Парткод:	M503489

Деталь:	SR-stay R
Парткод:	M503486

Деталь:	SL-stay
Парткод:	M503487

Деталь:	Maintenance cover sensor assy.
Парткод:	E102144

Деталь:	Cover cushion U
Парткод:	M700282

Деталь:	SR-stay L
Парткод:	M503485

Деталь:	Y-cover angle
Парткод:	M503465

Деталь:	Cover sensor assy.
Парткод:	E102143

Деталь:	Front cover switch bracket
Парткод:	M503488

Деталь:	Sub side plate R assy.
Парткод:	M503519

Деталь:	Media guide
Парткод:	M503159

Деталь:	Media guide shaft
Парткод:	M600946

Деталь:	Platen rubber 130
Парткод:	M700286

Деталь:	Platen rubber 160
Парткод:	M700287

Деталь:	Platen rubber 180
Парткод:	M700290

Деталь:	Platen cover R 130
Парткод:	M503507

Деталь:	Platen cover R 160
Парткод:	M503508

Деталь:	Platen cover R 180
Парткод:	M503616

Деталь:	P-cover bracket 2
Парткод:	M503521

Деталь:	Platen F 130
Парткод:	M300730

Деталь:	Platen F 160
Парткод:	M300731

Деталь:	Platen F 180
Парткод:	M300732

Деталь:	Paper sensor assy.
Парткод:	E102024

Деталь:	Paper sensor R bracket
Парткод:	M503524

Деталь:	P-cover bracket
Парткод:	M502718

Деталь:	Support assy.
Парткод:	M004012

Деталь:	Platen cover F 130
Парткод:	M503509

Деталь:	Platen cover F 160
Парткод:	M503510

Деталь:	Platen cover F 180
Парткод:	M503617

Деталь:	P-cover F rubber130
Парткод:	M700284

Деталь:	P-cover F rubber160
Парткод:	M700285

Деталь:	P-cover F rubber180
Парткод:	M700291

Деталь:	Electrical unit bracket
Парткод:	M503437

Деталь:	POWER SUPPLY ASSY.
Парткод:	E300264

Деталь:	Main FPC cable 1 assy.
Парткод:	E102036

Деталь:	Main FPC cable 2 assy.
Парткод:	E102045

Деталь:	DC CABLE ASSY.
Парткод:	E102033

Деталь:	FG CABLE ASSY.
Парткод:	E102042

Деталь:	HDC-2Head PCB assy.
Парткод:	E102053

Деталь:	Protection Plate
Парткод:	E300299

Деталь:	HDC-4Head PCB assy.
Парткод:	E102052

Деталь:	HDC FPC assy.
Парткод:	E102037

Деталь:	HDC FPC 160 assy.
Парткод:	E102062

Деталь:	HDC FPC 180 assy.
Парткод:	E102111

Деталь:	Cooling fan motor assy.
Парткод:	E102020

Деталь:	Roll base plate
Парткод:	M600906

Деталь:	Pinch screw
Парткод:	M600056

Деталь:	Roll base L
Парткод:	M503444

Деталь:	Roll holder shaft130/160
Парткод:	M203334

Деталь:	Roll holder G
Парткод:	M600686

Деталь:	Roll sub shaft
Парткод:	M300726

Деталь:	Roll holder
Парткод:	M600500

Деталь:	Belt screw
Парткод:	M400140

Деталь:	Roll stopper A
Парткод:	M601087

Деталь:	Roll stopper B2
Парткод:	M503829

Деталь:	Roll stopper spring 2
Парткод:	M800604

Деталь:	Roll base R2
Парткод:	M503830

Деталь:	Roll holder gear
Парткод:	M601168

Деталь:	Roll holder shaft R 130/160
Парткод:	M203498

Деталь:	Roll base L assy.
Парткод:	M004727

Деталь:	Roll base R assy.
Парткод:	M004728

Деталь:	X-pulley bracket
Парткод:	M503418

Деталь:	Pulley stopper
Парткод:	M203353

Деталь:	TN15-160 pulley
Парткод:	M203155

Деталь:	Bearing holder 1
Парткод:	M400212

Деталь:	Driving roller 130 L
Парткод:	M203456

Деталь:	Driving roller 160 L
Парткод:	M203457

Деталь:	Driving roller 180 L
Парткод:	M203436

Деталь:	X-axis motor assy.
Парткод:	E300294

Деталь:	TN15-20 pulley
Парткод:	M203154

Деталь:	X-motor junction cable assy.
Парткод:	E102012

Деталь:	X-motor junction cable 160 assy.
Парткод:	E102059

Деталь:	X-motor junction cable 180 assy.
Парткод:	E102110

Деталь:	XM-bracket
Парткод:	M503419

Деталь:	Coupling L
Парткод:	M203310

Деталь:	Driving roller A
Парткод:	M203307

Деталь:	Driving roller B
Парткод:	M203308

Деталь:	Driving roller 180 R
Парткод:	M203435

Деталь:	BR shaft
Парткод:	M203306

Деталь:	Bearing holder 2
Парткод:	M400213

Деталь:	X-Origin sensor assy.
Парткод:	E102128

Деталь:	X-Origin motor total assy.
Парткод:	M004348

Деталь:	Y-spring plate
Парткод:	M503406

Деталь:	Y-spring
Парткод:	M800569

Деталь:	Y-T fulcrum pin
Парткод:	M202842

Деталь:	Y-T pulley bracket
Парткод:	M502878

Деталь:	Y-T bracket
Парткод:	M502877

Деталь:	Belt holderl
Парткод:	M400160

Деталь:	D-bracket U
Парткод:	M502708

Деталь:	Y-drive pulley
Парткод:	M201960

Деталь:	D-pulley
Парткод:	M202822

Деталь:	DM-pulley
Парткод:	M202666

Деталь:	Y-axis motor assy.
Парткод:	E300295

Деталь:	D-bracket
Парткод:	M503403

Деталь:	YM-spacer
Парткод:	M202665

Деталь:	YM-top plate
Парткод:	M502710

Деталь:	Belt support plate S
Парткод:	M503786

Деталь:	Belt screw
Парткод:	M400140

Деталь:	Belt holder
Парткод:	M400161

Деталь:	S3M Belt 130
Парткод:	M800563

Деталь:	S3M Belt 160
Парткод:	M800572

Деталь:	S3M Belt 180
Парткод:	M800591

Деталь:	Y-driven pulley
Парткод:	M201966

Деталь:	Y-T pulley shaft
Парткод:	M202841

Деталь:	Y-driven pulley assy.
Парткод:	M002732

Деталь:	Y-drive pulley assy.
Парткод:	M004363

Деталь:	Y-drive motor total assy.
Парткод:	M004725

Деталь:	Keyboard seat
Парткод:	M902731

Деталь:	LCD COVER
Парткод:	M600520

Деталь:	Keyboard panel
Парткод:	M601023

Деталь:	KEY TOP
Парткод:	M601024

Деталь:	Keyboard PCB assy.
Парткод:	E102058

Деталь:	Ink sensor PCB assy.
Парткод:	E101910

Деталь:	Keyboard cable assy.
Парткод:	E102032

Деталь:	Keyboard base
Парткод:	M503500

Деталь:	IO PCB assy.
Парткод:	E102056

Деталь:	KB panel assy.
Парткод:	M004393

Деталь:	Bear guide-film 130
Парткод:	M902668

Деталь:	Bear guide-film 160
Парткод:	M902676

Деталь:	Bear guide-film 180
Парткод:	M902794

Деталь:	Bear base
Парткод:	M503417

Деталь:	Belt screw
Парткод:	M400140

Деталь:	Bear holder
Парткод:	M503596

Деталь:	Bear guide 130
Парткод:	M503391

Деталь:	Bear guide 160
Парткод:	M503416

Деталь:	Bear guide 180
Парткод:	M503598

Деталь:	FPC holder
Парткод:	M503388

Деталь:	FPC clamp bracket
Парткод:	M503387

Деталь:	Bear guide stay
Парткод:	M503458

Деталь:	Y-bar 130
Парткод:	M300717

Деталь:	Y-bar 160
Парткод:	M300723

Деталь:	Y-bar 180
Парткод:	M300754

Деталь:	LM guide 130
Парткод:	M800490

Деталь:	LM guide 160
Парткод:	M800571

Деталь:	LM guide 180
Парткод:	M800590

Деталь:	Scale holder
Парткод:	M601077

Деталь:	YL-cover 130
Парткод:	M503484

Деталь:	YL-cover 160/180
Парткод:	M503493

Деталь:	SL stay
Парткод:	M503487

Деталь:	LEFT SIDE PLATE
Парткод:	M503474

Деталь:	Y-cover angle
Парткод:	M503465

Деталь:	Front cover D catch bracket
Парткод:	M503489

Деталь:	Cover cushion D
Парткод:	M700283

Деталь:	Cover cushion U
Парткод:	M700282

Деталь:	Sub side plate L
Парткод:	M503466

Деталь:	Ink sensor PCB assy.
Парткод:	E101910

Деталь:	Under cover L
Парткод:	M503523

Деталь:	Under cover L 160/180
Парткод:	M503559

Деталь:	SL-cover 130
Парткод:	M503482

Деталь:	SL-cover 160/180
Парткод:	M503492

Деталь:	LEFT COVER
Парткод:	M601022

Деталь:	Cartridge cover L 130
Парткод:	M503426

Деталь:	Cartridge cover L 160/180
Парткод:	M503427

Деталь:	Cartridge rear cover L 130
Парткод:	M503429

Деталь:	Cartridge rear cover L 160/180
Парткод:	M503430

Деталь:	Guide KCM
Парткод:	M503431

Деталь:	Guide YGO
Парткод:	M503432

Деталь:	Tube cover 130
Парткод:	M503532

Деталь:	Tube cover 160/180
Парткод:	M503533

Деталь:	Cartridge cover R
Парткод:	M503425

Деталь:	Cartridge rear cover R
Парткод:	M503428

Деталь:	Cartridge base R
Парткод:	M600595

Деталь:	Plate spring (C)
Парткод:	M502166

Деталь:	Cartridge base bracket R
Парткод:	M503422

Деталь:	Cartridge base bracket L 130
Парткод:	M503423

Деталь:	Cartridge base bracket L 160/180
Парткод:	M503424

Деталь:	Cartridge guide 2
Парткод:	M600593

Деталь:	Cartridge guide 1
Парткод:	M600592

Деталь:	Cartridge frame assy.
Парткод:	M004275

Деталь:	Cartridge guide assy.
Парткод:	M004730

Деталь:	Roll bracket
Парткод:	M503442

Деталь:	Roll holder shaft 180
Парткод:	M203335

Деталь:	Roll holder G
Парткод:	M600686

Деталь:	Extension long bushing (180)
Парткод:	M202507

Деталь:	Roll base180
Парткод:	M203337

Деталь:	Sub roll shaft stay
Парткод:	M503445

Деталь:	Main roll shaft 180
Парткод:	M203343

Деталь:	Sub roll shaft 180
Парткод:	M300728

Деталь:	Roll guide collar
Парткод:	M203338

Деталь:	Frame 130
Парткод:	M300739

Деталь:	Frame 160
Парткод:	M300740

Деталь:	Frame 180
Парткод:	M300764

Деталь:	Y-bar bracket
Парткод:	M400157

Деталь:	Absorption Pad
Парткод:	M700288

Деталь:	Absorber S-S
Парткод:	M902740

Деталь:	Under frame 130
Парткод:	M503501

Деталь:	Under frame 160
Парткод:	M503512

Деталь:	Under frame 180
Парткод:	M503518

Деталь:	Fan motor bracket
Парткод:	M503513

Деталь:	Fan motor 1 assy.
Парткод:	E102017

Деталь:	Fan motor 2 assy.
Парткод:	E102018

Деталь:	Fan motor 3 assy.
Парткод:	E102019

Деталь:	Fan motor 3 160 assy.
Парткод:	E102060

Деталь:	Absorption Pad
Парткод:	M700305

Деталь:	Fan motor 4 180assy.
Парткод:	E102144

Деталь:	Clamp bushing
Парткод:	M600694

Деталь:	Clamp end bracket
Парткод:	M503514

Деталь:	CL B assy.
Парткод:	M503515

Деталь:	Roll stopper C
Парткод:	M601088

Деталь:	Lever G
Парткод:	M601090

Деталь:	Clamp link
Парткод:	M503516

Деталь:	Lever assy.
Парткод:	M503518

Деталь:	Clamp lever
Парткод:	M601066

Деталь:	Clamp sensor assy.
Парткод:	E102026

Деталь:	Clamp sensor bracket
Парткод:	M503520

Деталь:	Clamp shaft 130
Парткод:	M203347

Деталь:	Clamp shaft 160
Парткод:	M203348

Деталь:	Clamp shaft 180
Парткод:	M203432

Деталь:	Clamp guard
Парткод:	M601119

Деталь:	P-holder
Парткод:	M503421

Деталь:	Clamp bushing
Парткод:	M600694

Деталь:	Main cam
Парткод:	M600663

Деталь:	Clamp spring
Парткод:	M800576

Деталь:	PR-base R
Парткод:	M503383

Деталь:	PINCH ROLLER
Парткод:	M600995

Деталь:	PR-shaft
Парткод:	M202720

Деталь:	PR-base F
Парткод:	M400181

Деталь:	P-holder shaft
Парткод:	M203304

Деталь:	PR assy.
Парткод:	M004726

Деталь:	FPC cover
Парткод:	M503464

Деталь:	FPC guide plate
Парткод:	M503389

Деталь:	TUBE GUIDE
Парткод:	M503412

Деталь:	Origin sensor assy.
Парткод:	E102025

Деталь:	Slider stopper R
Парткод:	M503503

Деталь:	Scale holder R
Парткод:	M503398

Деталь:	Linear encoder scale assy.
Парткод:	E300245

Деталь:	Linear encoder scale 160 assy.
Парткод:	E300289

Деталь:	Linear encoder scale 180 assy.
Парткод:	E102115

Деталь:	Linear encoder PCB assy.
Парткод:	E102044

Деталь:	L sensor bracket
Парткод:	M503404

Деталь:	SLIDER
Парткод:	M400214

Деталь:	SHAFT HOLDER
Парткод:	M203319

Деталь:	HEAD BASE
Парткод:	M400209

Деталь:	H-axis hold shaft
Парткод:	M203317

Деталь:	Scale hook
Парткод:	M503397

Деталь:	Scale spring
Парткод:	M800565

Деталь:	Slider stopper L
Парткод:	M503504

Деталь:	Scale holder L
Парткод:	M503399

Деталь:	Slider PCB bracket
Парткод:	M503390

Деталь:	Slider PCB assy.
Парткод:	E102054

Деталь:	Head FPC 6 assy.
Парткод:	E102050

Деталь:	Head FPC 5 assy.
Парткод:	E102049

Деталь:	Head FPC 4 assy.
Парткод:	E102048

Деталь:	Head FPC 3 assy.
Парткод:	E102047

Деталь:	Head FPC 2 assy.
Парткод:	E102046

Деталь:	Head FPC 1 assy.
Парткод:	E102038

Деталь:	Roll bracket
Парткод:	M503442

Деталь:	Sub roll shaft 130
Парткод:	M300726

Деталь:	Sub roll shaft 160
Парткод:	M300727

Деталь:	Sub roll shaft 180
Парткод:	M300728

Деталь:	Roll base M
Парткод:	M600509

Деталь:	HOLDER SHAFT
Парткод:	M202118

Деталь:	Roll holder
Парткод:	M600500

Деталь:	Sub roll shaft stay
Парткод:	M503445

Деталь:	Extension bushing
Парткод:	M600541

Деталь:	Extension long bushing
Парткод:	M600540

Деталь:	Main wind-up shaft 130
Парткод:	M203339

Деталь:	Main wind-up shaft 160
Парткод:	M203340

Деталь:	Main wind-up shaft 180
Парткод:	M203341

Деталь:	TL shaft (180)
Парткод:	M202502

Деталь:	Wind-up cover
Парткод:	M601026

Деталь:	TL bracket
Парткод:	M503529

Деталь:	TL gear (180)
Парткод:	M400202

Деталь:	Take-up motor cable assy.
Парткод:	E102129

Деталь:	Take-up motor PCB assy.
Парткод:	E101185

Деталь:	M gear (A) (180)
Парткод:	M202782

Деталь:	Take-up motor bracket
Парткод:	M503530

Деталь:	Take-up motor switch assy.
Парткод:	E101209

Деталь:	Take-up motor assy.
Парткод:	E101604

Деталь:	Take-up right assy.
Парткод:	M004403

Деталь:	Station shaft assy.
Парткод:	M003973

Деталь:	Absorber S-L
Парткод:	M902741

Деталь:	Station cam
Парткод:	M601047

Деталь:	Station motor assy.
Парткод:	E102142

Деталь:	Station motor gear
Парткод:	M400211

Деталь:	Station gear 2
Парткод:	M601046

Деталь:	Station gear 1
Парткод:	M601045

Деталь:	CAM SHAFT
Парткод:	M300729

Деталь:	Bottom point sensor assy.
Парткод:	E102028

Деталь:	D-point sensor bracket
Парткод:	M503453

Деталь:	Pump motor 1 assy.
Парткод:	E102137

Деталь:	Pump motor 2 assy.
Парткод:	E102138

Деталь:	Pump motor 3 assy.
Парткод:	E102139

Деталь:	Pump motor 4 assy.
Парткод:	E102140

Деталь:	Pump-middle gear
Парткод:	M601044

Деталь:	Pump motor gear
Парткод:	M400210

Деталь:	Pump motor bracket
Парткод:	M003971

Деталь:	Pump bracket
Парткод:	M503446

Деталь:	Station base
Парткод:	M003972

Деталь:	Wiper holder
Парткод:	M601015

Деталь:	Wiper holder base
Парткод:	M601019

Деталь:	Wiper belt holder
Парткод:	M503456

Деталь:	Wiper gear S
Парткод:	M601055

Деталь:	ABSORBER
Парткод:	M902739

Деталь:	Wiper ink guard
Парткод:	M503531

Деталь:	Wiper shaft S
Парткод:	M203344

Деталь:	Wiper bracket S
Парткод:	M003974

Деталь:	Wiper sensor bracket
Парткод:	M503454

Деталь:	Wiper sensor assy.
Парткод:	E102029

Деталь:	Cap housing U
Парткод:	M600999

Деталь:	CAP SPRING
Парткод:	M800573

Деталь:	Cap housing D
Парткод:	M601000

Деталь:	Cap sensor plate
Парткод:	M503450

Деталь:	Cam bridge
Парткод:	M503449

Деталь:	Station spring
Парткод:	M800575

Деталь:	Cap frame
Парткод:	M503448

Деталь:	Station guide
Парткод:	M601052

Деталь:	Wiper motor bracket S
Парткод:	M503455

Деталь:	Station motor gear
Парткод:	M400211

Деталь:	Wiper motor assy.
Парткод:	E102141

Деталь:	Cleaning wiper kit
Парткод:	SPA-0105

Деталь:	Cap housing assy.
Парткод:	M004359

Деталь:	Damper holder
Парткод:	M601129

Деталь:	Print head cover
Парткод:	M600998

Деталь:	Print head assy.
Парткод:	M004372

Деталь:	Head guide shaft
Парткод:	M203315

Деталь:	Head bracket
Парткод:	M400207

Деталь:	Angle spring
Парткод:	M800570

Деталь:	Head adjusting screw
Парткод:	M400208

Деталь:	Adjusting Spring
Парткод:	M800566

Деталь:	ADJUSTER
Парткод:	M601048

Деталь:	Head slider
Парткод:	M400203

Деталь:	Stand top R
Парткод:	M503526

Деталь:	Stand foot
Парткод:	M300733

Деталь:	Right stand assy.
Парткод:	M004194

Деталь:	Left stand assy.
Парткод:	M004195

Деталь:	Stand top L
Парткод:	M503527

Деталь:	Stay 130
Парткод:	M300735

Деталь:	Stay 160
Парткод:	M300736

Деталь:	Stay 180
Парткод:	M300737

Деталь:	Head H shaft
Парткод:	M203316

Деталь:	H-adjuster
Парткод:	M601049

Деталь:	H-adjust spring
Парткод:	M800567

Деталь:	Head UD bracket
Парткод:	M503402

Деталь:	Head cover bracket
Парткод:	M503463

Деталь:	Cutter cover
Парткод:	M503462

Деталь:	Cutter unit base
Парткод:	M503392

Деталь:	Cap sensor assy.
Парткод:	E102027

Деталь:	Paper width sensor assy.
Парткод:	E102023

Деталь:	Cutter bracket
Парткод:	M503393

Деталь:	CUTTER HOLDER
Парткод:	M601053

Деталь:	Cutter actuator assy.
Парткод:	E102022

Деталь:	Cutter L
Парткод:	M201535

Деталь:	Cutter roller
Парткод:	M601085

Деталь:	Cutter screw
Парткод:	M400219

Деталь:	CUTTER HOLDER
Парткод:	M601086

Деталь:	Cutter shaft
Парткод:	M203322

Деталь:	Pin spring
Парткод:	M800564

Деталь:	Pin guide
Парткод:	M601050

Деталь:	Height adjusting pin
Парткод:	M203314

Деталь:	HEAD COVER
Парткод:	M503467

Деталь:	H-axis fixing shaft
Парткод:	M203318

Деталь:	H-axis stopper
Парткод:	M601051

Деталь:	Cutter assy.
Парткод:	SPA-0107

Деталь:	Rear cover L 130
Парткод:	M503476

Деталь:	Rear cover L 160
Парткод:	M503477

Деталь:	Rear cover L 180
Парткод:	M503599

Деталь:	Rear cover R 130
Парткод:	M503556

Деталь:	Rear cover R 160
Парткод:	M503557

Деталь:	Rear cover R 180
Парткод:	M503600

Деталь:	Y-cover 130
Парткод:	M503468

Деталь:	Y-cover 160
Парткод:	M503469

Деталь:	Y-cover 180
Парткод:	M503470

Деталь:	Stay support
Парткод:	M503461

Деталь:	Y-cover stay 130
Парткод:	M503471

Деталь:	Y-cover stay 160
Парткод:	M503472

Деталь:	Y-cover stay 180
Парткод:	M503473

Деталь:	Front cover U 130
Парткод:	M503491

Деталь:	Front cover U 160
Парткод:	M503494

Деталь:	Front cover U 180
Парткод:	M503495

Деталь:	Fulcrum pin
Парткод:	M201625

Деталь:	Pin bracket
Парткод:	M501584

Деталь:	Front cover nut 130
Парткод:	M503497

Деталь:	Front cover nut 160
Парткод:	M503498

Деталь:	Front cover nut 180
Парткод:	M503499

Деталь:	Front cover switch washer
Парткод:	M503490

Деталь:	Front cover nut C
Парткод:	M503496

Деталь:	Front cover D 130
Парткод:	M601081

Деталь:	Front cover D 160
Парткод:	M601082

Деталь:	Front cover D 180
Парткод:	M601083

Деталь:	Cover spring
Парткод:	M800095

Деталь:	Front cover assy. 130
Парткод:	M004721

Деталь:	Front cover assy. 160
Парткод:	M004722

Деталь:	Front cover assy. 180
Парткод:	M004723

Деталь:	INK FPC 1 160 assy.
Парткод:	E102063

Деталь:	INK FPC 1 180 assy.
Парткод:	E102112

Деталь:	Electrical unit cover
Парткод:	M503439

Деталь:	I/Fconnection board assy.
Парткод:	E102154

Деталь:	1394 PCB assy.
Парткод:	E102161

Деталь:	Inlet cover
Парткод:	M503441

Деталь:	I/F bracket
Парткод:	M503438

Деталь:	INLET ASSY.
Парткод:	E102041

Деталь:	AC CABLE ASSY.
Парткод:	E102034

Деталь:	Main PCB bracket
Парткод:	M503440

Деталь:	Main PCB assy.
Парткод:	E102051

Деталь:	INK FPC 1 assy.
Парткод:	E102039

Деталь:	INK FPC 2 assy.
Парткод:	E102040

Деталь:	IO cable assy.
Парткод:	E102035

Error code:	01
Display:	ERROR CONDITION INVALID HEAD
Description:	The ERROR light flashes.
Causes:	The printhead was replaced with one that is not a genuine Zebra™ printhead.
Remedy:	Install a genuine Zebra printhead.

Error code:	02
Display:	ERROR CONDITION RIBBON OUT
Description:	The printer stops; the ERROR light flashes.
Causes:	In thermal transfer mode, ribbon is not loaded or incorrectly loaded. In thermal transfer mode, the ribbon sensor is not detecting ribbon that is loaded incorrectly. In thermal transfer mode, media is blocking the ribbon sensor. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly.
Remedy:	Load ribbon correctly. 1. Load ribbon correctly. See Load Ribbon on page 64. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Load media correctly. See Load Media on page 58. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Print a sensor profile. See Print Sensor Profile on page 89. The ribbon out threshold (marked by the word RIBBON) is likely too high, above the black area that indicates where the ribbon is detected. 2. Calibrate the sensors or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73.

Error code:	03
Display:	WARNING RIBBON IN
Description:	The ERROR light flashes.
Causes:	Ribbon is loaded, but the printer is set for direct thermal mode.
Remedy:	Ribbon is not required with direct thermal media. If you are using direct thermal media, remove the ribbon. This error message will not affect printing. If you are using thermal transfer media, which requires ribbon, set the printer for Thermal Transfer mode. See Select Print Method on page 81.

Error code:	04
Display:	ERROR CONDITION PAPER OUT
Description:	The printer stops; the ERROR light flashes.
Causes:	The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded.
Remedy:	Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration.

Error code:	06
Display:	THERMISTOR FAULT
Description:	The ERROR light flashes.
Causes:	The printhead has a faulty thermistor.
Remedy:	Replace the printhead.

Error code:	07
Display:	WARNING HEAD COLD, THERMISTOR FAULT, ERROR CONDITION HEAD ELEMENT BAD
Description:	The printer stops; the ERROR light is on; the printer cycles through these three messages.
Causes:	The printhead data cable is not properly connected. The printhead has a faulty thermistor.
Remedy:	Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead.

Error code:	08
Display:	WARNING HEAD COLD
Description:	The printer prints while the ERROR light flashes.
Causes:	The printhead temperature is approaching its lower operating limit. The printhead data cable is not properly connected. The printhead has a faulty thermistor.
Remedy:	Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the printer to a warmer area. Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead.

Error code:	09
Display:	WARNING HEAD TOO HOT
Description:	The printer stops; the ERROR light flashes.
Causes:	The printhead is over temperature.
Remedy:	Allow the printer to cool. Printing automatically resumes when the printhead elements cool to an acceptable operating temperature.

Error code:	10
Display:	DEFRAGMENTING
Description:	The printer stops.
Causes:	The printer is defragmenting memory.
Remedy:	Caution • Do NOT turn off the printer power during defragmenting. Doing so can damage the printer. Allow the printer to finish defragmenting. If you get this error message frequently, check your label formats. Formats that write to and erase memory frequently may cause the printer to defragment often. Using properly coded label formats usually minimizes the need for defragmenting. If this error message does not go away, contact Technical Support. The printer requires service.

Error code:	11
Display:	ERROR CONDITION CUTTER JAM
Description:	The printer stops; the ERROR light flashes.
Causes:	Caution • The cutter blade is sharp. Do not touch or rub the blade with your fingers. The cutter blade is in the media path.
Remedy:	Turn off the printer power and unplug the printer. Inspect the cutter module for debris and clean as needed following the cleaning instructions in Clean the Cutter Module on page 135.

Error code:	12
Description:	General print quality issues
Causes:	The printer is set at the incorrect print speed. You are using an incorrect combination of labels and ribbon for your application. The printer is set at an incorrect darkness level. The printhead is dirty. Incorrect or uneven printhead pressure. The printhead is improperly balanced.
Remedy:	For optimal print quality, set the print speed to the lowest possible setting for your application via control panel, the driver, or the software. See Adjust Print Speed on page 79. You may want to perform the FEED Self Test on page 120. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. For optimal print quality, set the darkness to the lowest possible setting for your application via the control panel, the driver, or the software. See Adjust Print Darkness on page 78. You may want to perform the FEED Self Test on page 120 to determine the ideal darkness setting. Clean the printhead. See Clean the Printhead and Platen Roller on page 131. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Adjust the printhead balance.

Error code:	20
Description:	Vertical image or label drift
Causes:	The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media.
Remedy:	Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation.

Error code:	21
Description:	The bar code printed on a label does not scan.
Causes:	The bar code is not within specifications because the print is too light or too dark. Not enough blank space around the bar code.
Remedy:	Perform the FEED Self Test on page 120. Adjust the darkness or print speed settings as necessary. Leave at least 1/8 in. (3.2 mm) between the bar code and other printed areas on the label and between the bar code and the edge of the label.

Error code:	23
Description:	Auto Calibrate failed.
Causes:	Media or ribbon is loaded incorrectly. The sensors could not detect the media or ribbon. The sensors are dirty or positioned improperly. The sensors are dirty, or media is positioned improperly for the sensors to detect. The media type is set incorrectly.
Remedy:	Ensure that media and ribbon are loaded correctly. Manually calibrate the printer. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Ensure that the sensors are clean and that media is positioned properly. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81.

Error code:	24
Description:	A label format was sent to the printer but was not recognized. The DATA light does not flash.
Causes:	The communication parameters are incorrect.
Remedy:	Check the printer driver or software communications settings (if applicable). If you are using serial communication, check the serial port setting in the control panel menu. See Set Serial Communications on page 91. If you are using serial communication, make sure you are using a null modem cable or a null modem adapter. Using the control panel controls, check the protocol setting. It should be set to NONE. See Set Protocol on page 93. If a driver is used, check the driver communication settings for your connection.

Error code:	30
Description:	The LCD displays a language that I cannot read
Causes:	The language parameter was changed through the control panel or a firmware command.
Remedy:	1. Press SETUP/EXIT to enter configuration mode. 2. Press MINUS (-). The printer displays the LANGUAGE parameter in the current language. Even if you cannot recognize the characters displayed, you can still scroll to another language. 3. Press SELECT to select the parameter. 4. Press PLUS (+) or MINUS (-) to scroll through the choices until you find a language that you can read. 5. Press SETUP/EXIT. The LCD displays SAVE CHANGES in the original language. 6. Press SETUP/EXIT again to exit configuration mode and save the changes (if the language does not change, you may need to scroll to a different save option by pressing PLUS (+) or MINUS (-) in the previous step). 7. Repeat this process, if necessary, until you reach the desired language.

Error code:	34
Description:	Non-continuous labels are being treated as continuous labels.
Causes:	The printer was not calibrated for the media being used. The printer is configured for continuous media.
Remedy:	Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81.

Error code:	40
Display:	Scanner locked
Description:	10-348 ERROR 40 FUSER MAIN LAMP FAILURE Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault, Clear <10-348 & 10-350> is run.
Causes:	1. Deformed paper sensor actuator or faulty sensor. 2. SMPS PBA or Main PBA is defective 3. Faulty cables or connectors.
Remedy:	Switch printer power OFF. Remove the Fuser Assembly. Warning Fuser may be very hot. Use extreme caution to prevent burns. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Replace the Engine Control Board.

Error code:	41
Display:	Self Diagnostic LSU
Description:	Install or Reseat Fuser, Code 41 Front thermistor open error. This is a cold condition. Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault is performed.
Causes:	• Fuser • Engine Control Board
Remedy:	1 1. Turn OFF power and remove the Fuser Assembly. 2. Measure the resistance between the fuser connector P600-4 and P600-6. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 2. Replace the fuser assembly. 2 1. Reinstall the fuser assembly. 2. Enter service diagnostics. 3. From the Sensor Tests run the Fuser Temperature test. 4. Is the temperature indicated approximately 165o C? Replace the engine control board. Go to step 3. 3 1. Turn OFF printer power. 2. Check for an open circuit or poor connection between J600-4 to J600-6 to J404A-2. 3. Is the wiring OK? Replace the engine control board. Repair or replace the wiring harness.

Error code:	42
Display:	Self Diagnostic Temperature
Description:	10-352 ERROR 42 FUSER STS (FRONT) WARM TIME FAILURE
Causes:	1. The ‘Open Cover’ microswitch may be stuck or faulty 2. The tab on the front cover may be damaged or broken 3. Check the connector and cables between Switch and main PBA.
Remedy:	Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board.

Mimaki JV4-180

Общие характеристики

Тип устройства

Печать фотографий

Факс

Телефон

Сканер

Копир

Макс. формат

Цветность печати

Технология печати

Тип

Принтер

Двусторонняя печать

Печать без полей

Прямая печать

Макс, разрешение для ч/б печати

Сканер

Отправка изображения по e-mail

Стандарт WIA

Стандарт TWAIN

Печать на:

Факс

Цветной

Телефон

Стандарт DECT

Проводная трубка

Беспроводная трубка

АОН

Caller ID

Автоответчик

Спикерфон

Языки управления

Финишер

Электронная сортировка

Сортер

Сортировка со сдвигом

Степлер

Брошюровщик

Интерфейсы

FireWire (IEEE 1394)

Wi-Fi

USB

Ethernet (RJ-45)

Устройство для чтения карт памяти

Веб-интерфейс

RS-232

Инфракрасный порт

LPT

Bluetooth

Поддержка ОС

Габариты

Глубина

Ширина

Высота

Вес

Модули

Детали

Коды ошибок

Описание

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Error code:	43
Display:	Send Error (AUTH)
Description:	10-353 ERROR 43 FUSER SSR1 ON TIME FAILURE
Causes:	1. The ‘Open Cover’ microswitch may be stuck or faulty 2. Check the connector and cables between Switch and main PBA.
Remedy:	Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board.

Error code:	45
Display:	Send Error (POP3)
Description:	Fuser STS (Rear) Failure, Code 45 Rear Thermistor open error. The machine logic detected an open circuit in the rear thermistor.
Causes:	• Fuser • Engine Control Board
Remedy:	1 1. Turn OFF power, remove the fuser assembly and allow it to cool down. 2. Measure the resistance between the Fuser connector P600-7 and P600-9. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 2. Replace the fuser assembly. 2 1. Reinstall the fuser assembly. 2. Enter service diagnostics. 3. From the Sensor Tests run the Fuser Temperature test. 4. Is the temperature indicated approximately 165o C? Replace the engine control board. Go to step 3. 3 1. Turn printer power OFF. 2. Check for an open circuit or poor connection between J641-4 and J641-5. 3. Is the wiring harness OK? Replace the engine control board. Repair or replace the wiring harness.

Error code:	46
Display:	Send Error (SMTP)
Description:	10-354 ERROR 46 FUSER STS (REAR) WARM TIME FAILURE
Causes:	1. Check stability of 24V supply to LSU.
Remedy:	Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-7 and P600-9. Does the resistance measure between 20 ohms and 100 ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-3 and P404A-4 on the Engine Control Board. Does the resistance measure between 20K ohms and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board.

Error code:	50
Display:	Tray 2 Paper Empty
Description:	Fuser Fan Failure The Fuser Fan rotation signal indicates to the Engine Control Board that the fan is no longer operational.
Causes:	• Fuser Fan, PL5.3.31 • FAN/PHD/MOT Harness, PL10.1.9 • Engine Control Board, PL9.1.16
Remedy:	1 Check the Fuser Fan for damage. Remove the Front Cover. Is the fan damaged? Replace the Fuser Fan. Go to Step 2. 2 Check the Fuser Fan connection. Is P/J482 connected to the harness? Go to Step 2. Reconnect the Fan. 3 Check orientation of the Fuser Fan. Does the Fan’s label face into the chute? Go to Step 3. Correct the installation. 4 Test the Fuser Fan. Run the Service Diagnostics Fuser Fan test. Does the Fan operate. Go to Step 6. Go to Step 5. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J482. 2. Check continuity between J48 <=> P483. Go to Step 5. Replace the FAN/PHD/MOT Harness. 6 Check the fan rotation signal. Print one sheet. Is there +3.3 V across P/J48-A12 <=> P/J48-A13? Replace the Engine Control Board. Replace the Fuser Fan.

Error code:	51
Display:	Send Error (DNS)
Description:	Rear Fan Failure The Rear Fan rotation signal indicates the fan is no longer operational.
Causes:	• Rear Fan, PL1.1.19 • LVPS, PL9.1.6 • Engine Control Board, PL9.1.16 • LV Harness, PL10.1.2
Remedy:	1 Check the Rear Fan for damage. Remove the Rear Cover. Is the fan damaged? Replace the Rear Fan. Go to Step 2. 2 Check the Rear Fan connection. Is P/J166 connected to the harness? Go to Step 3. Connect the Fan. 3 Check orientation of the Rear Fan. Does the Fan’s label face inwards? Go to Step 4. Correct the installation. 4 Test the Rear Fan. Run the Service Diagnostics Rear Fan test. Does the fan operate? Go to Step 6. Go to Step 5. 5 Check for +24 V to the fan. Disconnect P/J166. Is there +24 V across P166-1 <=> P166-3? Replace the Rear Fan. Replace the LVPS. 6 Check the fan rotation signal to the LVPS. Print one sheet. Is there +3.3 V between P/J166-1 <=> P/J166-3? Replace the Fuser Fan. Go to Step 7. 7 Check the rotation signal from the LVPS. Print one sheet. Is there +3.3 V between P/J165-15 <=> P/J165-3? Replace the LVPS. Go to Step 8. 8 Check the fan rotation signal at the Engine Control Board. Print one sheet. Is there +3.3 V between P/J61-4 <=> P/J61-16? Replace the LV Harness Replace the Engine Control Board.