Mimaki UJF-6042 MkII
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
пьезоэлектрическая струйная
Макс. формат
A2
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Технология печати |
пьезоэлектрическая струйная |
Факс |
|
Сканер |
|
Телефон |
|
Копир |
|
Размещение |
напольный |
Макс. формат |
A2 |
Тип устройства |
Принтер |
Цветность печати |
цветная |
Принтер |
|
Количество цветов |
8 |
Двусторонняя печать |
|
Макс, разрешение для ч/б печати |
|
| По X | 1 200 |
| По Y | 1 200 |
Сканер |
|
Слайд-адаптер |
|
Стандарт TWAIN |
|
Стандарт WIA |
|
Отправка изображения по e-mail |
|
Расходные материалы |
|
Количество картриджей |
8 |
Печать на: |
|
| Матовой бумаге |
|
| Пленках |
|
| Фотобумаге |
|
| Глянцевой бумаге |
|
| Этикетках |
|
| CD/DVD |
|
| Карточках |
|
Факс |
|
Цветной |
|
Телефон |
|
Беспроводная трубка |
|
АОН |
|
Стандарт DECT |
|
Автоответчик |
|
Caller ID |
|
Спикерфон |
|
Проводная трубка |
|
Языки управления |
|
| PostScript |
|
Финишер |
|
Сортировка со сдвигом |
|
Электронная сортировка |
|
Сортер |
|
Степлер |
|
Брошюровщик |
|
Интерфейсы |
|
LPT |
|
AirPrint |
|
Инфракрасный порт |
|
RS-232 |
|
FireWire (IEEE 1394) |
|
Wi-Fi |
|
Устройство для чтения карт памяти |
|
Bluetooth |
|
Ethernet (RJ-45) |
|
USB |
|
Дополнительная информация |
|
Работа от аккумулятора |
|
Поддержка ОС |
|
| Windows |
|
Потребляемая мощность |
|
| При работе | 800 |
Уровень шума |
|
| При работе | 70 |
| В режиме ожидания | 55 |
Габариты |
|
Вес |
155 |
Высота |
856 |
Глубина |
1 290 |
Ширина |
1 665 |
Модули
HEAD ASSY. -2/3
WIPER ASSY.
X GEAR BOX ASSY. (UJF-6042)
CHASSIS ASSY. -2/2 (UJF-6042)
STATION ASSY.
CARTRIDGE ASSY. -2/2
POWER SUPPLY CHASSIS ASSY.
Z TABLE ASSY. -3/4
COVER ASSY. -2/2
KEYBOARD ASSY.
Y BAR ASSY.
LED-UV WATER COOLING UNIT ASSY.
CHASSIS ASSY. -1/2
Z TABLE ASSY. -4/4
PUMP ASSY.
CARTRIDGE ASSY. -1/2
HEAD ASSY. -1/3
CHASSIS ASSY. -1/2 (UJF-6042)
BEAR ASSY.
Z TABLE ASSY. -1/4 (FAN)
CHASSIS ASSY. -2/2
COVER ASSY. -1/2
FRAME ASSY. -1/2
Z TABLE ASSY. -4/4 (UJF-6042)
HEAD ASSY. -3/3
UV LAMP ASSY.
Z TABLE ASSY. -3/4 (UJF-6042)
Y DRIVE ASSY.
FRAME ASSY. -2/2
Z TABLE ASSY. -2/4
Z TABLE ASSY. -1/4 (UJF-6042)
Z TABLE ASSY. -2/4 (UJF-6042)
WASTE INK ASSY.
X GEAR BOX ASSY.
Детали LED-UV WATER COOLING UNIT ASSY.
| Деталь: | Slider PCB cover |
| Парткод: | M515099 |
| Деталь: | HG Slider relay - slider cable assy. |
| Парткод: | E106784 |
| Деталь: | 6042 Slider relay - slider cable assy. |
| Парткод: | E107600 |
| Деталь: | IPPR3 Cascade short 13 assy. |
| Парткод: | E106086 |
| Деталь: | 3042 SLIDER PCB FM ASSY |
| Парткод: | MP-E106803 |
| Деталь: | FWR-P1.0-L1-30-1700 |
| Парткод: | MP-E300764 |
| Деталь: | FFC |
| Парткод: | MP-FWR-P1.0- L1-30-1900 |
| Деталь: | Slider PCB BKT |
| Парткод: | M514931 |
| Деталь: | Slider PCB BKT |
| Парткод: | M516603 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | MP-OJ-6505-N2 |
| Деталь: | Y bear spacer |
| Парткод: | M602938 |
| Деталь: | Sponge tape 300 |
| Парткод: | MP-M801819 |
| Деталь: | Wiper sub assy. |
| Парткод: | M012148 |
| Деталь: | Tension BUTdddddd |
| Парткод: | M512954 |
| Деталь: | STEP MOTOR |
| Парткод: | MP-E300924 |
| Деталь: | Station motor gear |
| Парткод: | MP-M400211 |
| Деталь: | Wiper BKT 2 |
| Парткод: | M512950 |
| Деталь: | Wiper sensor cable assy. |
| Парткод: | E106256 |
| Деталь: | Wiper gear S |
| Парткод: | M601055 |
| Деталь: | Wiper gear flange |
| Парткод: | M503696 |
| Деталь: | Belt presser |
| Парткод: | M512952 |
| Деталь: | Wiper BKT 1 |
| Парткод: | M512949 |
| Деталь: | Wiper cover |
| Парткод: | M512953 |
| Деталь: | Wiper slider assy. |
| Парткод: | MP-M010343 |
| Деталь: | Suck nozzle top |
| Парткод: | SPA-0182 |
| Деталь: | Suck nozzle under 1.5 |
| Парткод: | M602779 |
| Деталь: | Black single tube (100m length) |
| Парткод: | SJ-MMK-2.5x4 |
| Деталь: | Suck nozzle holder |
| Парткод: | M602623 |
| Деталь: | Up and Down guide BKT |
| Парткод: | M512951 |
| Деталь: | Wiper slider |
| Парткод: | M602624 |
| Деталь: | Guide Shaft |
| Парткод: | M206769 |
| Деталь: | WIPER ASSY. |
| Парткод: | MP-M010021 |
| Деталь: | Spiral tube W HG |
| Парткод: | M801506 |
| Деталь: | CE-012L V0 Push out edge |
| Парткод: | MM-000870 |
| Деталь: | X Speed reducer assy. |
| Парткод: | MP-M013633 |
| Деталь: | SCREW |
| Парткод: | MM-000551 |
| Деталь: | BEARING |
| Парткод: | MF105ZZ |
| Деталь: | SCREW |
| Парткод: | MM-000558 |
| Деталь: | XM top BKT |
| Парткод: | M516586 |
| Деталь: | TN15-24 pulley |
| Парткод: | M207793 |
| Деталь: | Hexagon socket head screw |
| Парткод: | MM-000745 |
| Деталь: | X motor BKT |
| Парткод: | M400536 |
| Деталь: | SCREW |
| Парткод: | MM-001198 |
| Деталь: | SCREW |
| Парткод: | MM-000347 |
| Деталь: | NUT |
| Парткод: | MM-000186 |
| Деталь: | Belt adjusting BKT |
| Парткод: | M516587 |
| Деталь: | SCREW |
| Парткод: | MM-000486 |
| Деталь: | SCREW |
| Парткод: | MM-000339 |
| Деталь: | Servomotor assy. (X) |
| Парткод: | MP-E300532 |
| Деталь: | TN15-72 pulley |
| Парткод: | M207790 |
| Деталь: | Nut BKT |
| Парткод: | M400537 |
| Деталь: | SCREW |
| Парткод: | MM-000333 |
| Деталь: | Support side |
| Парткод: | M400535 |
| Деталь: | C-ring |
| Парткод: | MM-000151 |
| Деталь: | SCREW |
| Парткод: | MM-000307 |
| Деталь: | Ball screw 6042 |
| Парткод: | M801654 |
| Деталь: | X bear retainer |
| Парткод: | M516616 |
| Деталь: | X bear cover |
| Парткод: | M513088 |
| Деталь: | SCREW |
| Парткод: | MM-000558 |
| Деталь: | HG X slider FG |
| Парткод: | E107020 |
| Деталь: | SCREW |
| Парткод: | MM-000564 |
| Деталь: | FFC holder |
| Парткод: | M603326 |
| Деталь: | SCREW |
| Парткод: | MM-000570 |
| Деталь: | X bear holder |
| Парткод: | M603329 |
| Деталь: | X shield plate |
| Парткод: | M513091 |
| Деталь: | Chassis 6042 |
| Парткод: | M516581 |
| Деталь: | BUSHING |
| Парткод: | MM-000677 |
| Деталь: | Electrical cable bear |
| Парткод: | M603328 |
| Деталь: | Square bush |
| Парткод: | MM-000900 |
| Деталь: | Side cover |
| Парткод: | M513079 |
| Деталь: | Chassis base M12 |
| Парткод: | M516620 |
| Деталь: | Front Panel |
| Парткод: | M516582 |
| Деталь: | Cable clamp UL |
| Парткод: | MM-000033 |
| Деталь: | Flat cable clamp |
| Парткод: | MM-000050 |
| Деталь: | Tool space |
| Парткод: | M602358 |
| Деталь: | STATION ASSY |
| Парткод: | MP-M011808 |
| Деталь: | PUMP ASSY |
| Парткод: | MP-M012022 |
| Деталь: | STATION SUB ASSY |
| Парткод: | MP-M011811 |
| Деталь: | WIPER ASSY HG |
| Парткод: | MP-M012023 |
| Деталь: | Cap slider assy. |
| Парткод: | M012151 |
| Деталь: | Cap ST base |
| Парткод: | M512958 |
| Деталь: | Fitting BKT |
| Парткод: | M512962 |
| Деталь: | Spiral tube C1, for cap 1 |
| Парткод: | M801319 |
| Деталь: | Spiral tube C2, for cap 2 |
| Парткод: | M801320 |
| Деталь: | Spiral tube C3, for cap 3 |
| Парткод: | M801321 |
| Деталь: | Spiral tube C4, for cap 4 |
| Парткод: | M801485 |
| Деталь: | Station tray |
| Парткод: | M514927 |
| Деталь: | Holder collar |
| Парткод: | M602631 |
| Деталь: | Waste tank screw |
| Парткод: | M801265 |
| Деталь: | Waste liquid tube holder |
| Парткод: | M602626 |
| Деталь: | Station absorber pad HG |
| Парткод: | M801505 |
| Деталь: | Cap slider U |
| Парткод: | M602596 |
| Деталь: | CAP ASSY. |
| Парткод: | M012112 |
| Деталь: | CAP PLATE R |
| Парткод: | MP-M602803 |
| Деталь: | CAP RUBBER R |
| Парткод: | MP-M700652 |
| Деталь: | Cap base R 1.5 |
| Парткод: | M602811 |
| Деталь: | Cap spring RM |
| Парткод: | M801312 |
| Деталь: | CAP SLIDER D |
| Парткод: | M602595 |
| Деталь: | Cap slider base |
| Парткод: | M602594 |
| Деталь: | FITTING ASSY |
| Парткод: | MP-M010014 |
| Деталь: | WASTE INK TUBE ASSY 1 |
| Парткод: | MP-M010530 |
| Деталь: | WASTE INK TUBE ASSY 2 |
| Парткод: | MP-M010531 |
| Деталь: | WASTE INK TUBE ASSY 3 |
| Парткод: | MP-M010532 |
| Деталь: | Mark tube |
| Парткод: | MTUB5_1-1 |
| Деталь: | Mark tube |
| Парткод: | MTUB5_1-2 |
| Деталь: | Mark tube |
| Парткод: | MTUB5_1-3 |
| Деталь: | Mark tube |
| Парткод: | MTUB5_1-4 |
| Деталь: | WASTE INK TUBE ASSY 4 |
| Парткод: | MP-M011958 |
| Деталь: | Wiper absorber pad |
| Парткод: | M801482 |
| Деталь: | Solenoid BKT |
| Парткод: | M514941 |
| Деталь: | LINK |
| Парткод: | M601336 |
| Деталь: | Ink cartridge solenoid |
| Парткод: | E300816 |
| Деталь: | Snap pin A |
| Парткод: | M801089 |
| Деталь: | Cartridge coupling assy. |
| Парткод: | M601427 |
| Деталь: | ID CONTACT BD CN032-2_ASSY |
| Парткод: | MP-E106699 |
| Деталь: | Cartridge frame |
| Парткод: | M602681 |
| Деталь: | Cartridge guide 1 |
| Парткод: | M602679 |
| Деталь: | Cartridge guide 2 |
| Парткод: | M602680 |
| Деталь: | Valve cap (Black) |
| Парткод: | M602143 |
| Деталь: | Valve spring washer |
| Парткод: | M204082 |
| Деталь: | Rubber valve |
| Парткод: | M700625 |
| Деталь: | Cartridge valve spring HG |
| Парткод: | M801515 |
| Деталь: | Valve base |
| Парткод: | M602854 |
| Деталь: | O-ring S4 |
| Парткод: | M700408 |
| Деталь: | Cap nut S4-M10PS |
| Парткод: | M207413 |
| Деталь: | UJF-3042 Main PCB assy. |
| Парткод: | MP-E106243 |
| Деталь: | 6042 MAIN PCB ASSY |
| Парткод: | MP-E107531 |
| Деталь: | Power supply chassis |
| Парткод: | M514922 |
| Деталь: | Power supply chassis |
| Парткод: | M516619 |
| Деталь: | HG noise filter connection assy. |
| Парткод: | E107000 |
| Деталь: | I/F label 3042 |
| Парткод: | M907140 |
| Деталь: | Manufacture label UJF-3042HG |
| Парткод: | M908538 |
| Деталь: | Manufacture label UJF-6042 |
| Парткод: | M909419 |
| Деталь: | Label-VCCI/FCC (for china) |
| Парткод: | M902535 |
| Деталь: | Label-power supply |
| Парткод: | M908784 |
| Деталь: | Label - Earth |
| Парткод: | M902324 |
| Деталь: | AC inlet assy. |
| Парткод: | E106253 |
| Деталь: | HG noise filter power supply connection assy. |
| Парткод: | E107001 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | MP-E300442 |
| Деталь: | X motor relay cable assy. |
| Парткод: | E106257 |
| Деталь: | 6042 X motor relay cable assy. |
| Парткод: | E107486 |
| Деталь: | FWR-TN2-P1.0-L1-30-2300 |
| Парткод: | MP-E300763 |
| Деталь: | Main - slider relay cable assy. |
| Парткод: | E107593 |
| Деталь: | X-origin sensor cable assy. |
| Парткод: | E106250 |
| Деталь: | FCR125R-20-0500 |
| Парткод: | MP-E300814 |
| Деталь: | FFC CABLE |
| Парткод: | MP-TFL125R-20- 0800(W5) |
| Деталь: | IF panel |
| Парткод: | M517646 |
| Деталь: | DDR2PRAM(1GB)PCB ASSY |
| Парткод: | MP-E105986 |
| Деталь: | Back cover under TB |
| Парткод: | M513096 |
| Деталь: | Caution Label |
| Парткод: | M904813 |
| Деталь: | PCB COVER |
| Парткод: | M516043 |
| Деталь: | Back cover TB |
| Парткод: | M516041 |
| Деталь: | ARM R |
| Парткод: | M512967 |
| Деталь: | Side cover R-TB |
| Парткод: | M513098 |
| Деталь: | Magnet catch BKT R |
| Парткод: | M513103 |
| Деталь: | Guide shaft B |
| Парткод: | M206841 |
| Деталь: | Shaft base |
| Парткод: | M206840 |
| Деталь: | TOP COVER |
| Парткод: | M513072 |
| Деталь: | TOP COVER |
| Парткод: | M516579 |
| Деталь: | Mimaki name plate |
| Парткод: | M602402 |
| Деталь: | IP line |
| Парткод: | M513078 |
| Деталь: | IP line |
| Парткод: | M516751 |
| Деталь: | FRONT COVER |
| Парткод: | M513071 |
| Деталь: | FRONT COVER |
| Парткод: | M516750 |
| Деталь: | Model label UJF-3042HG |
| Парткод: | M908536 |
| Деталь: | Model label UJF-6042 |
| Парткод: | M909417 |
| Деталь: | Caution Label |
| Парткод: | M904813 |
| Деталь: | Caution label-UV light |
| Парткод: | M905980 |
| Деталь: | Window plate -front cover |
| Парткод: | M602641 |
| Деталь: | Window plate -front cover |
| Парткод: | M603161 |
| Деталь: | RIGHT COVER |
| Парткод: | M602530 |
| Деталь: | Cover cap SB |
| Парткод: | M700517 |
| Деталь: | Cover-back right |
| Парткод: | M513074 |
| Деталь: | Station cover |
| Парткод: | M514947 |
| Деталь: | Caution label - Front cover |
| Парткод: | M901549 |
| Деталь: | Label-PUSH |
| Парткод: | M909424 |
| Деталь: | Middle right cover |
| Парткод: | M514949 |
| Деталь: | Front Panel |
| Парткод: | M513087 |
| Деталь: | KB side cover |
| Парткод: | M602533 |
| Деталь: | KB front cover top |
| Парткод: | M513080 |
| Деталь: | Remote switch assy. |
| Парткод: | E106251 |
| Деталь: | Switch Label-power supply |
| Парткод: | M904806 |
| Деталь: | Inter lock switch assy. |
| Парткод: | E106249 |
| Деталь: | KB label |
| Парткод: | M906906 |
| Деталь: | LCD window |
| Парткод: | M801272 |
| Деталь: | Keyboard BKT |
| Парткод: | M513081 |
| Деталь: | Key top GP |
| Парткод: | M602540 |
| Деталь: | FWR-P1.0-L1-10-1600 |
| Парткод: | MP-E300762 |
| Деталь: | KEYBOARD 3042LC PCB ASSY |
| Парткод: | MP-E106647 |
| Деталь: | KB cover under |
| Парткод: | M513083 |
| Деталь: | Y bar 3042 |
| Парткод: | M513057 |
| Деталь: | Y bar 6042 |
| Парткод: | M516599 |
| Деталь: | Origin sensor shade plate |
| Парткод: | M513047 |
| Деталь: | Scale base L |
| Парткод: | M513197 |
| Деталь: | Scale SP |
| Парткод: | M800565 |
| Деталь: | Oil guard |
| Парткод: | M513056 |
| Деталь: | Oil guard |
| Парткод: | M516600 |
| Деталь: | Scale base R |
| Парткод: | M513198 |
| Деталь: | Linear encoder scale 940 |
| Парткод: | MP-E300721 |
| Деталь: | LINEAR ENCODER SCALE 1250 |
| Парткод: | MP-E300969 |
| Деталь: | Scale holder R |
| Парткод: | M513265 |
| Деталь: | Scale stopper |
| Парткод: | M602224 |
| Деталь: | Scale holder |
| Парткод: | M601077 |
| Деталь: | Scale hook |
| Парткод: | M503397 |
| Деталь: | Scale holder L |
| Парткод: | M503399 |
| Деталь: | UV Radiator assy. |
| Парткод: | M011441 |
| Деталь: | Circulation pump sub assy. |
| Парткод: | M011955 |
| Деталь: | Circulation cover |
| Парткод: | M515346 |
| Деталь: | Liquid feeding pump head |
| Парткод: | MP-M801872 |
| Деталь: | Circulation P base |
| Парткод: | M515344 |
| Деталь: | Circulation P gear BKT |
| Парткод: | M515343 |
| Деталь: | FLANGE BUSH 80 |
| Парткод: | MP-80F-1003 |
| Деталь: | PUMP GEAR |
| Парткод: | MP-M400216 |
| Деталь: | FLANGE BUSH 80 |
| Парткод: | MP-80F-0605 |
| Деталь: | STEP MOTOR |
| Парткод: | MP-E300924 |
| Деталь: | Gear color |
| Парткод: | M204373 |
| Деталь: | GEAR 24 |
| Парткод: | M601073 |
| Деталь: | Circulation pump BKT |
| Парткод: | M515345 |
| Деталь: | Circulation pump absorption pad |
| Парткод: | M801504 |
| Деталь: | FITTING ASSY |
| Парткод: | MP-M010328 |
| Деталь: | Hot water tank cover |
| Парткод: | M602461 |
| Деталь: | FLOAT SWITCH ASSY |
| Парткод: | MP-E105378 |
| Деталь: | CENTRIFUGAL PUMP |
| Парткод: | MP-BR400-BM |
| Деталь: | Rubber packing |
| Парткод: | M700513 |
| Деталь: | Water cooling tank |
| Парткод: | M602777 |
| Деталь: | Radiator holder |
| Парткод: | M512981 |
| Деталь: | RADIATOR 120 |
| Парткод: | MP-M801270 |
| Деталь: | WATER COOLING FAN ASSY |
| Парткод: | MP-E106265 |
| Деталь: | Radiator fan BKT |
| Парткод: | M514225 |
| Деталь: | MAINTENANCE TUBE SET |
| Парткод: | MP-U-3.2(170)-5-WM4 SET |
| Деталь: | Right angle adjusting BKT |
| Парткод: | M513184 |
| Деталь: | X drive block base LH |
| Парткод: | M206785 |
| Деталь: | X drive block base |
| Парткод: | M206784 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | MP-OJ-6505-N2 |
| Деталь: | Chassis plate |
| Парткод: | M207330 |
| Деталь: | Side cover |
| Парткод: | M513079 |
| Деталь: | Front Panel |
| Парткод: | M513087 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | MP-OJ-6505-N2 |
| Деталь: | Z drive base |
| Парткод: | M512963 |
| Деталь: | BEARING |
| Парткод: | MP-F606ZZ |
| Деталь: | Nut BKT |
| Парткод: | M512972 |
| Деталь: | Z drive nut |
| Парткод: | M206770 |
| Деталь: | Z slide BKT |
| Парткод: | M512965 |
| Деталь: | Z drive screw |
| Парткод: | M206774 |
| Деталь: | Z motor reinforcement plate |
| Парткод: | M512974 |
| Деталь: | Z motor base |
| Парткод: | M512964 |
| Деталь: | SPUR WHEEL |
| Парткод: | MP-S80B 40B+0506 |
| Деталь: | Z-D GEAR |
| Парткод: | MP-M801292 |
| Деталь: | Z motor BKT |
| Парткод: | M512968 |
| Деталь: | STEP MOTOR |
| Парткод: | MP-E300924 |
| Деталь: | Z slide BKT R |
| Парткод: | M512966 |
| Деталь: | BEARING |
| Парткод: | MP-628ZZ |
| Деталь: | SHAFT |
| Парткод: | M206773 |
| Деталь: | Shaft slider R |
| Парткод: | M400442 |
| Деталь: | Shaft slider L |
| Парткод: | M400443 |
| Деталь: | STEP MOTOR |
| Парткод: | MP-E300924 |
| Деталь: | Gear collar |
| Парткод: | M204373 |
| Деталь: | GEAR 24 |
| Парткод: | M601073 |
| Деталь: | Pump motor BKT |
| Парткод: | M512957 |
| Деталь: | FLANGE BUSH 80 |
| Парткод: | MP-80F-0605 |
| Деталь: | PUMP GEAR |
| Парткод: | MP-M400216 |
| Деталь: | FLANGE BUSH 80 |
| Парткод: | MP-80F-1003 |
| Деталь: | Pump gear BKT |
| Парткод: | M512955 |
| Деталь: | Pump base |
| Парткод: | M512956 |
| Деталь: | Liquid feeding pump head |
| Парткод: | MP-M801872 |
| Деталь: | MAINTENANCE TUBE SET |
| Парткод: | MP-U-3.2(170)-5-WM4 SET |
| Деталь: | CARTRIDGE COVER |
| Парткод: | M514940 |
| Деталь: | Label-ink slot HG |
| Парткод: | M908504 |
| Деталь: | Ink slot guide GASS |
| Парткод: | M514938 |
| Деталь: | Ink slot guide BKT 2 |
| Парткод: | M514937 |
| Деталь: | Cartridge base 4P |
| Парткод: | M602837 |
| Деталь: | Plate spring C |
| Парткод: | M502166 |
| Деталь: | Ink slot base BKT 1 |
| Парткод: | M514936 |
| Деталь: | CR guide |
| Парткод: | M602456 |
| Деталь: | Ink slot base |
| Парткод: | M514935 |
| Деталь: | Coupling holder |
| Парткод: | M515103 |
| Деталь: | Cap nut S4-M10PL |
| Парткод: | M207414 |
| Деталь: | O-ring S4 |
| Парткод: | M700408 |
| Деталь: | F coupling 2.5 |
| Парткод: | M602875 |
| Деталь: | DUCT |
| Парткод: | M513107 |
| Деталь: | Duct suck mouth |
| Парткод: | M514945 |
| Деталь: | MIST ABSORPTION FAN ASSY |
| Парткод: | MP-E106318 |
| Деталь: | Head cover base |
| Парткод: | M514944 |
| Деталь: | Mist adsorption filter |
| Парткод: | SPC-0656 |
| Деталь: | Filter BKT |
| Парткод: | M513108 |
| Деталь: | Head slider base |
| Парткод: | M400436 |
| Деталь: | L sensor BKT |
| Парткод: | M508854 |
| Деталь: | LINEAR ENCORDER BOARD |
| Парткод: | MP-E103961 |
| Деталь: | Y-origin L-ENC cable assy. |
| Парткод: | E106247 |
| Деталь: | HEAD COVER |
| Парткод: | M514943 |
| Деталь: | Label - Air bleeder |
| Парткод: | M907144 |
| Деталь: | Right angle adjusting BKT |
| Парткод: | M513184 |
| Деталь: | SCREW |
| Парткод: | MM-000564 |
| Деталь: | NUT |
| Парткод: | MM-000186 |
| Деталь: | SCREW |
| Парткод: | MM-000347 |
| Деталь: | SCREW |
| Парткод: | MM-000325 |
| Деталь: | X drive block base |
| Парткод: | M400538 |
| Деталь: | SCREW |
| Парткод: | MM-000333 |
| Деталь: | Chassis plate |
| Парткод: | M207796 |
| Деталь: | SCREW |
| Парткод: | MM-000558 |
| Деталь: | Nylon clamp NK |
| Парткод: | MM-001348 |
| Деталь: | SCREW |
| Парткод: | MM-000911 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | MP-OJ-6505-N2 |
| Деталь: | SCREW |
| Парткод: | MM-000322 |
| Деталь: | Partition |
| Парткод: | M516618 |
| Деталь: | Y bear fix BKT |
| Парткод: | M514934 |
| Деталь: | FPC holder |
| Парткод: | M513090 |
| Деталь: | FPC holder |
| Парткод: | M603326 |
| Деталь: | Y bear BKT |
| Парткод: | M514933 |
| Деталь: | Y bear shield plate |
| Парткод: | M514930 |
| Деталь: | FFC 100R-30-1700 |
| Парткод: | E300764 |
| Деталь: | FFC |
| Парткод: | MP-FWR-P1.0- L1-30-1900 |
| Деталь: | Guide Film |
| Парткод: | M602893 |
| Деталь: | Micro coupler |
| Парткод: | MC-04SH |
| Деталь: | Quick coupling |
| Парткод: | LT2ASV2S2 |
| Деталь: | Tube FFC holder |
| Парткод: | M513059 |
| Деталь: | Bear guide |
| Парткод: | M514932 |
| Деталь: | Bear guide |
| Парткод: | M516601 |
| Деталь: | Y bear sound absorption material |
| Парткод: | M801502 |
| Деталь: | Y bear shield vibration material |
| Парткод: | M700703 |
| Деталь: | Hose clamp 1 |
| Парткод: | T603032 |
| Деталь: | Hose clamp 2 |
| Парткод: | T603034 |
| Деталь: | Adsorption table |
| Парткод: | M207193 |
| Деталь: | GASKET |
| Парткод: | M700581 |
| Деталь: | ABSORPTION FAN ASSY |
| Парткод: | MP-E106274 |
| Деталь: | Adsorption fan connector change assy. |
| Парткод: | E107184 |
| Деталь: | Adsorption fan relay cable assy. |
| Парткод: | E107185 |
| Деталь: | Adsorption FAN cover |
| Парткод: | M516040 |
| Деталь: | Back cover UTB |
| Парткод: | M516042 |
| Деталь: | Table support block L |
| Парткод: | M207443 |
| Деталь: | Side cover TB |
| Парткод: | M515371 |
| Деталь: | Table support block R |
| Парткод: | M207444 |
| Деталь: | Prohibition label-Overload 2kg (Jpn.) |
| Парткод: | M908914 |
| Деталь: | Table prohibition label-unbalanced overload |
| Парткод: | M903226 |
| Деталь: | Caution Label |
| Парткод: | M904813 |
| Деталь: | Prohibition label-Overload 2kg (Eng.) |
| Парткод: | M908915 |
| Деталь: | Table prohibition label-unbalanced overload |
| Парткод: | M904325 |
| Деталь: | Shading plate F |
| Парткод: | M515370 |
| Деталь: | Table support shaft 100 |
| Парткод: | M207445 |
| Деталь: | Table support shaft 50 |
| Парткод: | M207448 |
| Деталь: | TABLE |
| Парткод: | M207333 |
| Деталь: | Table guide shaft |
| Парткод: | M207175 |
| Деталь: | Adjusting BKT R |
| Парткод: | M513169 |
| Деталь: | Cam adjusting BKT R |
| Парткод: | M512960 |
| Деталь: | Up and Down cam |
| Парткод: | M400440 |
| Деталь: | Cam adjusting BKT L |
| Парткод: | M512971 |
| Деталь: | Table prohibition label-Overload |
| Парткод: | M907327 |
| Деталь: | Table prohibition label-Overload (Eng.) |
| Парткод: | M907328 |
| Деталь: | UV shading plate |
| Парткод: | M513092 |
| Деталь: | X shield plate |
| Парткод: | M513091 |
| Деталь: | FPC holder |
| Парткод: | M513090 |
| Деталь: | X bear retainer |
| Парткод: | M514921 |
| Деталь: | X bear cover |
| Парткод: | M513088 |
| Деталь: | Chassis |
| Парткод: | M514920 |
| Деталь: | Chassis base |
| Парткод: | M513089 |
| Деталь: | HG X slider FG |
| Парткод: | E107020 |
| Деталь: | BACK COVER |
| Парткод: | M513073 |
| Деталь: | BACK COVER |
| Парткод: | M516580 |
| Деталь: | Blindfold plate |
| Парткод: | M513187 |
| Деталь: | FFC holder sponge |
| Парткод: | M602669 |
| Деталь: | Cover-back left |
| Парткод: | M513075 |
| Деталь: | Cover-front left |
| Парткод: | M514948 |
| Деталь: | Label-cooling water pour |
| Парткод: | M907143 |
| Деталь: | Cover cap SB |
| Парткод: | M700517 |
| Деталь: | LEFT COVER |
| Парткод: | M602531 |
| Деталь: | Middle left cover |
| Парткод: | M514950 |
| Деталь: | HG SLIDER INTERCONNECT PCB |
| Парткод: | MP-E106962 |
| Деталь: | Ink slot frame |
| Парткод: | M513063 |
| Деталь: | HEAT RELEASE FAN ASSY |
| Парткод: | MP-E106268 |
| Деталь: | X bear fix BKT movement side |
| Парткод: | M513048 |
| Деталь: | FPC holder |
| Парткод: | M513090 |
| Деталь: | FPC holder |
| Парткод: | M603326 |
| Деталь: | Micro SW-BKT L |
| Парткод: | M513069 |
| Деталь: | MICRO SWITCH |
| Парткод: | MP-D3M-01K1-3 |
| Деталь: | Obstacle sensor BKT |
| Парткод: | M513170 |
| Деталь: | Photo sensor assy. |
| Парткод: | MP-E106259 |
| Деталь: | Cover fulcrum pin |
| Парткод: | M206790 |
| Деталь: | Y bar pillar LH |
| Парткод: | M514925 |
| Деталь: | Y bar pillar LH |
| Парткод: | M516598 |
| Деталь: | Y bar block |
| Парткод: | M400350 |
| Деталь: | Y bar block L |
| Парткод: | M400533 |
| Деталь: | Stopper t2 |
| Парткод: | M512982 |
| Деталь: | BUSHING |
| Парткод: | MM-000676 |
| Деталь: | FFC COVER |
| Парткод: | M514926 |
| Деталь: | 8ports clamp base |
| Парткод: | M602413 |
| Деталь: | 8ports clamp BKT |
| Парткод: | M510751 |
| Деталь: | HG centrifugal pump connection assy. |
| Парткод: | E106995 |
| Деталь: | Ink IC contact cable assy. |
| Парткод: | E106246 |
| Деталь: | Y motor relay cable assy. |
| Парткод: | E106258 |
| Деталь: | HG Water cooling FAN relay cable assy. |
| Парткод: | E107004 |
| Деталь: | Float switch relay cable assy. |
| Парткод: | E106346 |
| Деталь: | Cover- sensor cable assy. |
| Парткод: | E106401 |
| Деталь: | FWR-P1.25-L1-16-1200 |
| Парткод: | MP-E300766 |
| Деталь: | FFC |
| Парткод: | MP-FWR-P1.25- L1-16-1500 |
| Деталь: | IPPR3 Cascade short 13 assy. |
| Парткод: | E106086 |
| Деталь: | 3042 slider relay power supply short assy. |
| Парткод: | E106272 |
| Деталь: | Circulation pump connection assy. |
| Парткод: | E106999 |
| Деталь: | Ink IC contact cable +2 assy. |
| Парткод: | E106996 |
| Деталь: | Obstacle sensor BKT C |
| Парткод: | M516613 |
| Деталь: | PHOTO ELECTRIC SENSOR ASSY |
| Парткод: | MP-E107491 |
| Деталь: | Sponge tape 600 |
| Парткод: | MP-M801818 |
| Деталь: | STATION 3 PCB ASSY |
| Парткод: | MP-E105948 |
| Деталь: | 6042 Z MTR cable assy. |
| Парткод: | E107487 |
| Деталь: | 6042 Z ORG cable assy. |
| Парткод: | E107488 |
| Деталь: | PCB BKT |
| Парткод: | M516745 |
| Деталь: | ARM R |
| Парткод: | M517463 |
| Деталь: | Adjusting BKT R |
| Парткод: | M517622 |
| Деталь: | Guide shaft B |
| Парткод: | M206841 |
| Деталь: | Shaft base |
| Парткод: | M206840 |
| Деталь: | Magnet catch BKT R |
| Парткод: | M513103 |
| Деталь: | 6042 Cover sensor cable TB assy. |
| Парткод: | E107489 |
| Деталь: | MICRO SWITCH |
| Парткод: | MP-D3M-01K1-3 |
| Деталь: | Inter lock BKT |
| Парткод: | M513102 |
| Деталь: | Magnet catch BKT L |
| Парткод: | M513101 |
| Деталь: | Adjusting BKT L |
| Парткод: | M517623 |
| Деталь: | ARM L |
| Парткод: | M517464 |
| Деталь: | Cap nut S4-M10PS |
| Парткод: | M207413 |
| Деталь: | O-ring S4 |
| Парткод: | M700408 |
| Деталь: | GEN damper cover |
| Парткод: | M513111 |
| Деталь: | GEN COMPRESSION DAMPER |
| Парткод: | MP-M011417 |
| Деталь: | GEN UV compression damper assy. 621 |
| Парткод: | M012321 |
| Деталь: | R head holder screw |
| Парткод: | M206792 |
| Деталь: | HEAD UNIT ASSY |
| Парткод: | MP-M010010 |
| Деталь: | R head BKT-ANG |
| Парткод: | M400437 |
| Деталь: | Head angle plate spring |
| Парткод: | M512870 |
| Деталь: | R head BKT-FR |
| Парткод: | M400438 |
| Деталь: | HEAD BASE |
| Парткод: | M400469 |
| Деталь: | Base holder 1 |
| Парткод: | M400471 |
| Деталь: | Base holder 2 |
| Парткод: | M400472 |
| Деталь: | FITTING ASSY |
| Парткод: | MP-M010014 |
| Деталь: | Air bleeder BKT |
| Парткод: | M514942 |
| Деталь: | LED pointer assy. |
| Парткод: | E106245 |
| Деталь: | LED HOLDER |
| Парткод: | M601294 |
| Деталь: | AD base |
| Парткод: | M602365 |
| Деталь: | Adjuster TD |
| Парткод: | M400381 |
| Деталь: | GEN DAMPER ADAPTER ASSY |
| Парткод: | MP-M011103 |
| Деталь: | F coupling 2.5 |
| Парткод: | M602875 |
| Деталь: | Cap nut S4-M10P1L |
| Парткод: | M207414 |
| Деталь: | UV damper sealing rubber |
| Парткод: | MP-M700623 |
| Деталь: | UV head assy. |
| Парткод: | MP-M010552 |
| Деталь: | UV head assy. Hi |
| Парткод: | MP-M013773 |
| Деталь: | LED-UV fan filter |
| Парткод: | M907107 |
| Деталь: | FRONT COVER |
| Парткод: | M512986 |
| Деталь: | LED UV irradiation assy. |
| Парткод: | M010545 |
| Деталь: | LED UV irradiation assy. Hi |
| Парткод: | MP-M013774 |
| Деталь: | Water jacket |
| Парткод: | M801271 |
| Деталь: | Heat radiation sheet |
| Парткод: | M700585 |
| Деталь: | 1 inch-UV LED HI PCB assy. |
| Парткод: | MP-E107394 |
| Деталь: | REFLECTOR |
| Парткод: | M602612 |
| Деталь: | Glass cushion |
| Парткод: | M801269 |
| Деталь: | PROTECTION GLASS |
| Парткод: | MP-M801268 |
| Деталь: | GLASS HOLDER |
| Парткод: | M512979 |
| Деталь: | LED-UV offset assy. |
| Парткод: | M010655 |
| Деталь: | LED extend BKT |
| Парткод: | M513596 |
| Деталь: | Reflector BKT |
| Парткод: | M400441 |
| Деталь: | SIDE COVER R |
| Парткод: | M513594 |
| Деталь: | TOP COVER |
| Парткод: | M513595 |
| Деталь: | SIDE COVER L |
| Парткод: | M513593 |
| Деталь: | 3042 UV DRV control assy. |
| Парткод: | E106488 |
| Деталь: | LED UV x2 DRV PCB assy. |
| Парткод: | E106429 |
| Деталь: | LED UV DRIVER PCB assy |
| Парткод: | MP-E106646 |
| Деталь: | LED-UV connection cable assy. |
| Парткод: | E106487 |
| Деталь: | DRV PCB COOLING FAN ASSY |
| Парткод: | MP-E106489 |
| Деталь: | Z motor reinforcement plate |
| Парткод: | M512974 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | MP-OJ-6505-N2 |
| Деталь: | BEARING |
| Парткод: | MP-F606ZZ |
| Деталь: | Z drive screw |
| Парткод: | M206774 |
| Деталь: | Z drive base |
| Парткод: | M516739 |
| Деталь: | Nut BKT |
| Парткод: | M512972 |
| Деталь: | Z drive nut |
| Парткод: | M207844 |
| Деталь: | Z slider dog |
| Парткод: | M517491 |
| Деталь: | Z slide BKT |
| Парткод: | M516737 |
| Деталь: | Z motor base |
| Парткод: | M516736 |
| Деталь: | SPUR WHEEL |
| Парткод: | MP-S80B 40B+0506 |
| Деталь: | Z motor BKT |
| Парткод: | M512968 |
| Деталь: | STEP MOTOR |
| Парткод: | MP-E300924 |
| Деталь: | Z-D GEAR |
| Парткод: | MP-M801292 |
| Деталь: | Z slide BKT R |
| Парткод: | M516738 |
| Деталь: | Shaft slider R |
| Парткод: | M400442 |
| Деталь: | BEARING |
| Парткод: | MP-628ZZ |
| Деталь: | SHAFT |
| Парткод: | M206773 |
| Деталь: | Shaft slider L |
| Парткод: | M400443 |
| Деталь: | Y-T fulcrum shaft |
| Парткод: | M202842 |
| Деталь: | Y-Pulley base |
| Парткод: | M513193 |
| Деталь: | Y-T pulley BKT |
| Парткод: | M510408 |
| Деталь: | Y-SP |
| Парткод: | M800569 |
| Деталь: | Y-SP plate |
| Парткод: | M507642 |
| Деталь: | Y-T PULLEY ASSY |
| Парткод: | MP-M006977 |
| Деталь: | Y-T pulley shaft |
| Парткод: | M202841 |
| Деталь: | Y-T pulley |
| Парткод: | M205123 |
| Деталь: | TIMING BELT (Y DRIVE BELT) |
| Парткод: | MP-LSB-R 150 S3M 207 6 |
| Деталь: | TIMING BELT |
| Парткод: | MP-LSB-R 150 S3M 2697 |
| Деталь: | Y drive BKT top |
| Парткод: | M513192 |
| Деталь: | Y DRIVE PULLEY ASSY |
| Парткод: | MP-M006891 |
| Деталь: | BELT |
| Парткод: | MP-150 S2M 380G |
| Деталь: | Y drive BKT |
| Парткод: | M513194 |
| Деталь: | BEARING |
| Парткод: | MP-F607ZZ |
| Деталь: | YM top BKT |
| Парткод: | M513196 |
| Деталь: | Y motor BKT |
| Парткод: | M513195 |
| Деталь: | Belt tension SP |
| Парткод: | M800981 |
| Деталь: | Y-AXIS MOTOR ASSY / PUL |
| Парткод: | MP-M005144 |
| Деталь: | DM pulley |
| Парткод: | M202666 |
| Деталь: | Y-axis motor assy. |
| Парткод: | E300440 |
| Деталь: | Belt screw |
| Парткод: | M400284 |
| Деталь: | Belt holder 1 |
| Парткод: | M400160 |
| Деталь: | Belt holder S |
| Парткод: | M503786 |
| Деталь: | Y bar pillar RH |
| Парткод: | M516597 |
| Деталь: | Y bar block R |
| Парткод: | M400534 |
| Деталь: | X slider frame |
| Парткод: | M516588 |
| Деталь: | 6042 Diaphragm connection assy. |
| Парткод: | E107490 |
| Деталь: | PUMP 3 PCB ASSY |
| Парткод: | MP-E105949 |
| Деталь: | Side plate RH |
| Парткод: | M514929 |
| Деталь: | Obstacle sensor BKT |
| Парткод: | M513170 |
| Деталь: | Y bar pillar RH |
| Парткод: | M514924 |
| Деталь: | Y bar block |
| Парткод: | M400350 |
| Деталь: | Cover fulcrum pin |
| Парткод: | M206790 |
| Деталь: | X slider frame |
| Парткод: | M514923 |
| Деталь: | Origin sensor shading plate |
| Парткод: | M513047 |
| Деталь: | HG Diaphragm connection assy. |
| Парткод: | E107005 |
| Деталь: | Pump motor connection x4 assy. |
| Парткод: | E106997 |
| Деталь: | Wiper motor cable assy. |
| Парткод: | E106255 |
| Деталь: | Obstacle sensor BKT A |
| Парткод: | M516606 |
| Деталь: | Sensor screw BKT |
| Парткод: | M517588 |
| Деталь: | Obstacle sensor BKT B |
| Парткод: | M516612 |
| Деталь: | 3042 Station 3 PCB assy. |
| Парткод: | MP-E106328 |
| Деталь: | HG Z MTR cable assy. |
| Парткод: | E107003 |
| Деталь: | Z ORG cable assy. |
| Парткод: | E106264 |
| Деталь: | PCB BKT |
| Парткод: | M512969 |
| Деталь: | Side cover L-TB |
| Парткод: | M513097 |
| Деталь: | ARM L |
| Парткод: | M512970 |
| Деталь: | Shaft base |
| Парткод: | M206840 |
| Деталь: | Guide shaft B |
| Парткод: | M206841 |
| Деталь: | Inter lock BKT |
| Парткод: | M513102 |
| Деталь: | MICRO SWITCH |
| Парткод: | MP-D3M-01K1-3 |
| Деталь: | Cover sensor cable TB assy. |
| Парткод: | E106319 |
| Деталь: | Magnet catch BKT L |
| Парткод: | M513101 |
| Деталь: | Front cover TB |
| Парткод: | M513093 |
| Деталь: | Hinge BKT |
| Парткод: | M513100 |
| Деталь: | Front cover under TB |
| Парткод: | M513094 |
| Деталь: | Caution Label |
| Парткод: | M904813 |
| Деталь: | Adsorption table 6042 |
| Парткод: | M207800 |
| Деталь: | Adsorption fan x2 connector change assy. |
| Парткод: | E107492 |
| Деталь: | Adsorption fan x2 relay cable assy. |
| Парткод: | E107493 |
| Деталь: | Back cover UTB |
| Парткод: | M516748 |
| Деталь: | Side cover TB |
| Парткод: | M515371 |
| Деталь: | Adjustment shaft |
| Парткод: | M208479 |
| Деталь: | Table support block LC |
| Парткод: | M208476 |
| Деталь: | Table support block RC |
| Парткод: | M208477 |
| Деталь: | Adjustment reference shaft |
| Парткод: | M208521 |
| Деталь: | Shading plate F |
| Парткод: | M516747 |
| Деталь: | Prohibition label-Overload 2kg (Jpn.) |
| Парткод: | M908914 |
| Деталь: | Table prohibition label-unbalanced overload |
| Парткод: | M903226 |
| Деталь: | Caution Label |
| Парткод: | M904813 |
| Деталь: | Prohibition label-Overload 2kg (Eng.) |
| Парткод: | M908915 |
| Деталь: | Table prohibition label-unbalanced overload |
| Парткод: | M904325 |
| Деталь: | GASKET |
| Парткод: | M700581 |
| Деталь: | ABSORPTION FAN ASSY |
| Парткод: | MP-E106274 |
| Деталь: | Adsorption FAN cover |
| Парткод: | M516749 |
| Деталь: | Table support shaft 100C |
| Парткод: | M208478 |
| Деталь: | PCB COVER |
| Парткод: | M516744 |
| Деталь: | Back under cover TB |
| Парткод: | M516746 |
| Деталь: | Caution Label |
| Парткод: | M904813 |
| Деталь: | Back cover TB |
| Парткод: | M516743 |
| Деталь: | Side cover R-TB |
| Парткод: | M513098 |
| Деталь: | Front cover TB |
| Парткод: | M516734 |
| Деталь: | Hinge BKT |
| Парткод: | M513100 |
| Деталь: | Front under cover TB |
| Парткод: | M516735 |
| Деталь: | Side cover L-TB |
| Парткод: | M513097 |
| Деталь: | Table 6042 |
| Парткод: | M207799 |
| Деталь: | Table guide shaft |
| Парткод: | M207175 |
| Деталь: | Cam adjusting BKT B |
| Парткод: | M517947 |
| Деталь: | SPRING |
| Парткод: | DC505 |
| Деталь: | Up and Down cam |
| Парткод: | M400440 |
| Деталь: | Cam adjusting BKT R |
| Парткод: | M208306 |
| Деталь: | Table side cover R |
| Парткод: | M516741 |
| Деталь: | Cam adjusting BKT A |
| Парткод: | M517946 |
| Деталь: | Table front cover |
| Парткод: | M516742 |
| Деталь: | Prohibition label-Overload 2kg (Jpn.) |
| Парткод: | M908914 |
| Деталь: | Table prohibition label-unbalanced overload |
| Парткод: | M903226 |
| Деталь: | Prohibition label-Overload 2kg (Eng.) |
| Парткод: | M908915 |
| Деталь: | Table prohibition label-unbalanced overload |
| Парткод: | M904325 |
| Деталь: | Cam adjusting BKT L |
| Парткод: | M512971 |
| Деталь: | Table side cover L |
| Парткод: | M516740 |
| Деталь: | Diaphragm pump assy. |
| Парткод: | MP-E104675 |
| Деталь: | PRESSURE CONTROL PUMP ASSY |
| Парткод: | MP-E106684 |
| Деталь: | Waste tank BKT |
| Парткод: | M512945 |
| Деталь: | Waste tank BKT |
| Парткод: | M517589 |
| Деталь: | Bottle cap (with hole) |
| Парткод: | M602559 |
| Деталь: | Bottle packing |
| Парткод: | M700551 |
| Деталь: | Waste ink tank 1.6L |
| Парткод: | SPA-0173 |
| Деталь: | Waste tank adsorption pad |
| Парткод: | SPC-0658 |
| Деталь: | Back panel |
| Парткод: | M512948 |
| Деталь: | Waste tank flame |
| Парткод: | M512947 |
| Деталь: | Waste tank door |
| Парткод: | M512946 |
| Деталь: | Caution label-Work |
| Парткод: | M903330 |
| Деталь: | Caution Label |
| Парткод: | M904813 |
| Деталь: | X driven pulley assy. |
| Парткод: | MP-M010071 |
| Деталь: | X-T pulley |
| Парткод: | M801282 |
| Деталь: | Driven pulley shaft |
| Парткод: | M206791 |
| Деталь: | X belt T BKT |
| Парткод: | M513054 |
| Деталь: | X joint block |
| Парткод: | M206789 |
| Деталь: | Belt presser |
| Парткод: | M400444 |
| Деталь: | Torque stopper |
| Парткод: | M206787 |
| Деталь: | TORQUE LIMITER |
| Парткод: | MP-OTLC6-1000C |
| Деталь: | TIMING BELT |
| Парткод: | MP- GBTG200S2M1330 |
| Деталь: | X-gear box assy.II |
| Парткод: | MP-M014548 |
| Деталь: | Coupling double disc |
| Парткод: | MP-ARD-21A- 5Y-6Y |
| Деталь: | X-motor BKT |
| Парткод: | M513165 |
| Деталь: | Servomotor assy. (X) |
| Парткод: | MP-E300532 |
Коды ошибок
000
04
104
108
10a
10b
10e
10f
110
114
115
116
117
11b
11d
11e
11f
120
122
123
124
125
126
127
128
129
12d
12e
130
13c
13d
13e
13f
140
146
147
149
151
152
153
154
155
156
157
158
159
15a
15f
160
161
16e
170
171
172
201
202
203
303
304
305
401
402
403
404
406
40b
420
421
502
505
509
50a
50f
510
511
601
602
603
605
606
607
608
60b
60c
60d
60e
60f
610
611
612
613
614
615
702
705
706
707
708
70a
801
802
803
804
805
806
807
808
809
80a
80b
80c
80d
80e
80f
810
811
812
813
814
815
816
817
818
819
81a
81b
901
902
90d
n01
n02
n03
n04
n05
n06
n07
n08
n09
n10
n11
n12
n13
n14
n15
n16
n17
n18
n19
n20
Описание
| Error code: | 000 |
| Display: | SYSTEM HALT (*) 000 : UNNOWN ERR |
| Description: | Cover Open |
| Causes: | The front or top cover is open. |
| Remedy: | 1. Close the front or top cover. 2. Replace the interlock switches or actuator mechanism. |
| Error code: | 04 |
| Display: | ERROR CONDITION PAPER OUT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded. |
| Remedy: | Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration. |
| Error code: | 104 |
| Display: | Service Call 104: Error |
| Description: | Developer Motor Failure The Developer Motor rotation signal indicates that the motor is no longer operational. |
| Causes: | • Developer Drive Assembly, PL8.1.1 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11 • FAN/PHD/MOT Harness, PL10.1.9 |
| Remedy: | 1 Check the Developer Drive Assembly for damage. Are any parts of the Developer Drive Assembly damaged or excessively worn? Replace the Developer Drive Assy. Go to Step 2. 2 Check the Developer Motor connection. Is P/J491 connected to the harness? Go to Step 3. Reconnect the Developer Motor. 3 Test the Developer Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Developer Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Developer Motor. Is the +24 V across P/J491-1 <=> P/J 481-5? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J491. 2. Check continuity between J48 <=> J491. Replace the Engine Control Board. Replace the FAN/PHD/MOT Harness. |
| Error code: | 108 |
| Display: | Service Call 108:Error |
| Description: | Printhead Error |
| Remedy: | Yellow printhead lost Hsync Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J7 and J8 on the system board. Go to “System board” If the cables are connected correctly to the system board and to the printhead assembly, replace the “Printhead diagnostics”. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” |
| Error code: | 10a |
| Display: | SYSTEM HALT (*) 10a : HDC INIT |
| Description: | Initialization error of the Slider PCB (FPGA) |
| Remedy: | 1. Check the connections between the SL-Relay PCB and the Slider PCB, and then disconnect and connect the FFCs or the like. 2. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 3. Replace the FFCs and the cabeles of the above routes. 4. Replace the Slider PCB with a new one. 5. Replace the SL-Relay PCB with a new one. 6. Replace the Main PCB with a new one. |
| Error code: | 10b |
| Display: | SYSTEM HALT (*) 10b : PCB SLRY-F3 |
| Description: | Initialization error of the SL-Relay PCB (FPGA) |
| Remedy: | 1. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 2. Replace the FFCs of the above routes. 3. Replace the SL-Relay PCB with a new one. 4. Replace the Main PCB with a new one. |
| Error code: | 10e |
| Display: | SYSTEM HALT (*) 10e :FROM CLEAR |
| Description: | F-ROM CLEAR error (F-ROM clear unable) F-ROM is not clearable on Parameter writing, FW down loading and Log clearing. (fls_secclr) |
| Remedy: | 1. Execute the memory check (F-ROM) of [#TEST]. 2. Upload the parameter and initialize all parameters with [#PARAMETER]. 3. Replace the Main PCB with a new one. |
| Error code: | 10f |
| Display: | SYSTEM HALT (*) 10f : FROM WRITE |
| Description: | FROM WRITE error (F-ROM writing unable) F-ROM is not clearable on Parameter writing, FW down loading and Log clearing. (fls_secclr) |
| Remedy: | 1. Execute the memory check (F-ROM) of [#TEST]. 2. Upload the parameter and initialize all parameters with [#PARAMETER]. 3. Replace the Main PCB with a new one. |
| Error code: | 110 |
| Display: | SVC 110 ERROR |
| Description: | Printhead Error |
| Causes: | Incorrect color DTM installation, incorrect PCU installation, development bias error, MCU, LD control malfunction, loss of synchronization |
| Remedy: | No first Hysnc - cyan Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J8 and J9 on the system board. Go to “System board” on page 5-8. If the cables are connected correctly to the system board and to the printhead assembly, replace the “Printhead diagnostics”. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” |
| Error code: | 114 |
| Display: | Service Call 114:Error |
| Description: | Front Tamper Home Sensor Failure, Code 114 With the Front Tamper Home Sensor OFF the Front Tamper Home Sensor did not turn ON within 800 ms after the move to the Front Tamper Home position has begun. With the Front Tamper Home Sensor on the Front Tamper Sensor did not turn Off when the Front Tamper Home Sensor is deactuated. |
| Causes: | • Front Tamper Motor • Finisher Control Board |
| Remedy: | 1 1. Run the Front Tamper Low Front or Front Tamper Low Rear test in diagnostics. 2. Does the front tamper guide operate? Go to step 6. Go to step 2. 2 Does the front tamper motor operate? Check the tampering mechanism for a mechanical problem. Go to step 3. 3 1. Check pins J877 A pins 1,3,4 and 6. 2. Is +24 VDC present on any of the pins? Go to step 4. Go to step 5. 4 1. Check the following wires for and open circuit or short circuit to ground. Is any wire open or shorted? J877A-1 to J848B-7 J877A-3 to J848B-9 J877A-4 to J848B-10 J877A-6 to J848B-12 Repair or replace the wiring harness. Replace in order until resolved: • front tamper motor • finisher control board 5 Is +24 VDC present on pins J848B-8 and J848B-11 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. 6 1. Check the tamper front home sensor in diagnostics. 2. Does the value change from H to L when the tamper is moved away from the home position? Replace the finisher control board. Repair the sensor using the Transmissive Sensor troubleshooting procedure. |
| Error code: | 115 |
| Display: | Service Call 115:Error |
| Description: | Rear Tamper Home Sensor Failure, Code 115 With the Rear Tamper Home Sensor OFF the Rear Tamper Home Sensor did not turn On within 800 ms after the move to the Rear Tamper Home position has begun. With the Rear Tamper Home Sensor on the Rear Tamper Sensor did not turn Off when the Rear Tamper Home Sensor is deactuated. |
| Causes: | • Rear Tamper Motor • Finisher Control Board |
| Remedy: | 1 1. Run the Rear Tamper Low Front or Rear Tamper Low Rear test in diagnostics. 2. Does the rear tamper guide operate? Go to step 6. Go to step 2. 2 Does the rear tamper motor operate? Check the tampering mechanism for a mechanical problem. Go to step 3. 3 1. Check pins J878A pins 1,3,4 and 6. 2. Is +24 VDC present on any of the pins? Go to step 4. Go to step 5. 4 1. Check the following wires for and open circuit or short circuit to ground. 2. Is any wire open or shorted? 3. J878A-1 to J848B-1 4. J878A-3 to J848B-3 5. J878A-4 to J848B-4 6. J878A-6 to J848B-6 Repair or replace the wiring harness. Replace in order until resolved: • rear tamper motor • finisher control board 5 Is +24 VDC present on pins J848B-2 and J848B-5 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. 6 1. Check the tamper rear home sensor in diagnostics. 2. Does the value change from H to L when the tamper is moved away from the home position? Replace the finisher control board. Repair the sensor circuit using the transmissive sensor troubleshooting procedure. |
| Error code: | 116 |
| Display: | SYSTEM HALT (*) 116 : PCB MAIN-F2 |
| Description: | Finisher Stacker Height Sensor Off Failure, Code 116 The Stack Height Sensor did not detect that the tray went down within 5 seconds after the Stacker Tray had been signaled to lower down at initialization. Or, the Stack Height Sensor did not detect the tray moving up within 5 seconds after the Stacker Tray had been signaled to lift. |
| Causes: | • Stacker Height Sensor/Actuator • Finisher Control Board |
| Remedy: | 1 1. Actuate the stacker height sensor in diagnostics. 2. Does the value change between H and L? Go to step 2. Troubleshoot using the transmissive sensor procedure. 2 1. Run the Finisher Stacker Motor Down test in diagnostics. 2. Does the stacker tray lower? Go to step 5. Go to step 3. 3 Does the stacker motor turn? Diagnose and repair the mechanical problem. Check the stacker motor gear, stacker tray, and belt track gear. Go to step 4. 4 Is +24 VDC present at P/J 847-12 with the Finisher Stacker Motor Down test running in diagnostics? Replace the stacker motor. Replace the finisher control board. 5 1. Run the Finisher Stacker Motor Up test in diagnostics. 2. Does the stacker tray move up? Replace the finisher control board. Go to step 6. 6 Does the sacker motor turn? Diagnose and repair the mechanical problem. Check the stacker motor gear, stacker tray, and belt track gear. Go to step 7. 7 Is +24 VDC present at P/J 847-11 with the Finisher Stacker Motor Down test running in diagnostics? Replace the stacker motor. Replace the finisher control board. |
| Error code: | 117 |
| Display: | SYSTEM HALT (*) 117 : PCB MAIN-F3 |
| Description: | Finisher Stacker Tray Failure, Code 117 The system detected that the Stacker Tray Upper Limit Sensor was turned ON after the Stacker Tray began lifting up. Or the Stacker Tray Upper Limit Sensor remained on after the lowering down of the Stacker Tray was completed. |
| Causes: | • Stacker Motor • Finisher Control Board |
| Remedy: | 1 1. Actuate the stacker upper limit sensor in diagnostics. 2. Does the value change between H and L? Go to step 2. Troubleshoot using the transmissive sensor procedure. 2 1. Run the Finisher Stacker Motor Down test in diagnostics. 2. Does the stacker tray lower? Go to step 5. Go to step 3. 3 Does the stacker motor turn? Diagnose and repair the mechanical problem. Check the stacker motor gear, stacker tray, and belt track gear. Go to step 4. 4 Is +24 VDC present at P/J 847-12 with the Finisher Stacker Motor Down test running in diagnostics? Replace the stacker motor. Replace the finisher control board. 5 1. Run the Finisher Stacker Motor Up test in diagnostics. 2. Does the stacker tray move up? Replace the finisher control board. Go to step 6. 6 Does the stacker motor turn? Diagnose and repair the mechanical problem. Check the stacker motor gear, stacker tray and belt track gear. Go to step 7. 7 Is +24 VDC present at P/J 847-11 with the Finisher Stacker Motor Down test running in diagnostics? Replace the stacker motor. Replace the finisher control board. |
| Error code: | 11b |
| Display: | SYSTEM HALT (*) 11b : SLDR FPC L |
| Description: | Connection check error of FPC cable between SL-Relay PCB and Slider PCB |
| Remedy: | 1. Check whether FPC cable connection connector of the Slider PCB (CN2, 4, 6) and the SL-Relay PCB (CN3, 7, 8) is proper. 2. Disconnect and connect the FFC and Twist pair Cable located between the Slider PCB and the SL-Relay PCB. 3. Disconnect and connect the FFC and Twist pair Cable located between the Main PCB and the SL-Relay PCB. 4. Replace the FFC(or Twist pair Cable) located between the Slider PCB and the SL-Relay PCB. 5. Replace the FFC(or Twist pair Cable) located between the Main PCB and the SL-Relay PCB. 6. Replace the Slider PCB with a new one. 7. Replace the SL-Relay PCB with a new one. 8. Replace the Main PCB with a new one. |
| Error code: | 11d |
| Display: | SYSTEM HALT (*) 11d : PCB SLRY-F1 |
| Description: | SL-Relay PCB fuse (F1) disconnected. |
| Remedy: | Replace the SL-Relay PCB with a new one. Before SL-Relay PCB replace, do the following checks. 1. Check the connections between the Slider PCB and the SL-Relay PCB, and then disconnect and connect the FFCs. 2. Check short between 1 pin and 4 pin of CN1, and between 1 pin and 9 pin of CN11 of the Slider PCB. (If shorted out, replace also the Slider PCB.) |
| Error code: | 11e |
| Display: | SYSTEM HALT (*) 11e : PCB SLRY-F4 |
| Description: | No SL-Relay PCB. |
| Remedy: | 1. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 2. Replace the FFCs of the above routes. 3. Replace the SL-Relay PCB with a new one. 4. Replace the Main PCB with a new one. |
| Error code: | 11f |
| Display: | SYSTEM HALT (*) 11f : PCB SLIDER |
| Description: | No Slider PCB. |
| Remedy: | 1. Check the connections between the SL-Relay PCB and the Slider PCB, and then disconnect and connect the FFCs or the like. 2. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 3. Replace the FFCs and the cabeles of the above routes. 4. Replace the Slider PCB with a new one. 5. Replace the SL-Relay PCB with a new one. 6. Replace the Main PCB with a new one. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 122 |
| Display: | Service Call 122: Error |
| Description: | Finisher Decurler Failure, Code 122 The level of the Decurler Cam Home Sensor did not change 4 seconds after the Decurler Cam Clutch has turned on. |
| Causes: | • Decurler Cam Clutch • Stacker Motor • Finisher Control Board |
| Remedy: | 1 1. Rotate the actuator while running the Decurler Cam Position test in diagnostics. 2. Does the value change between H and L? Go to step 2. Troubleshoot using the transmissive sensor procedure. 2 Does the decurler cam clutch operate in diagnostics? Check for a mechanical problem with the decurler cam clutch drive. If no problem is found replace the clutch. Go to step 3. 3 Is +24 VDC present at P/J 849-1? Replace the decurler cam clutch. Go to step 4. 4 Is +24 VDC present at test point 5 on the finisher control board? Replace the finisher control board. Troubleshoot the +24 VDC interlock circuit. 5 Is +24 VDC present at P/J 847-11 with the Finisher Stacker Motor Down test running in diagnostics? Replace the stacker motor. Replace the finisher control board |
| Error code: | 123 |
| Display: | Service Call 123: Error |
| Description: | Finisher Set Clamp Failure, Code 123 The set clamp home sensor did not turn on within 2 seconds after the set clamp started operation. |
| Causes: | • Set Clamp Solenoid • Finisher Control Board |
| Remedy: | 1 1. Check the Set Clamp home sensor in diagnostics. 2. Does the value change from H to L while rotating the actuator? Go to step 2. Use the transmissive Sensor procedure to diagnose and repair the sensor. 2 Does the solenoid energize when running the Set Clamp Paddle test in diagnostics? Go to step 3. Go to step 4. 3 1. Run the Eject Forward Test and then the Eject Release Test in diagnostics. 2. Does the set clamp paddle turn once? Replace the finisher control board. Go to step 4. 4 Is +24 VDC present at P848A-10? Go to step 5. Go to step 6. 5 Is +24 VDC present at P848A-11? Replace the finisher control board. Replace the set clamp solenoid. 6 Is +24 VDC present at test point 9 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. |
| Error code: | 124 |
| Display: | Service Call 124: Error |
| Description: | Finisher Communication Failure, Code 124 |
| Remedy: | There are no diagnostic routines for problems involving serial communications. It is recommended that you address the following assemblies in this order: • Finisher Control Board • Engine Control Board • Perform continuity checks on any wiring harnesses involved. |
| Error code: | 125 |
| Display: | Service Call 125: Error |
| Description: | Finisher Staple Mode Logic Failure, Code 125 |
| Remedy: | There are no diagnostic routines for problems involving serial communications. It is recommended that you address the following assemblies in this order: • Stapler Assembly • Engine Control Board • Perform continuity checks on any wiring harnesses involved. |
| Error code: | 126 |
| Display: | Turn power OFF and wait 126: Dew error |
| Description: | Fuser Error |
| Causes: | Sensor dew error detected. |
| Remedy: | Fuser open thermistor hot roll |
| Error code: | 127 |
| Display: | Contact the Service center. 127: Error |
| Description: | Fuser Error |
| Causes: | • Scanner motor defective (motor lead connected incorrectly) • MCU board defective (scanner motor control unit) |
| Remedy: | Fuser open thermistor BUR |
| Error code: | 128 |
| Display: | Service Call 128: Error |
| Description: | Fuser Error |
| Causes: | • Scanner motor defective • Overload on scanner mechanism • PSU-Eb board defective • MCU board defective (scanner motor control unit) |
| Remedy: | Fuser under temperature in standby - hot roll |
| Error code: | 129 |
| Display: | ERROR 129 BATTERY EXCHANGE |
| Description: | Fuser Error |
| Causes: | • Scanner motor defective • Scanner drive mechanism defective • PSU-Eb board defective • MCU board defective (scanner motor control unit) |
| Remedy: | Fuser under temperature in standby - BUR |
| Error code: | 12d |
| Display: | SYSTEM HALT (*) 12d : PCB MAIN-F4 |
| Description: | Main PCB fuse (F4) disconnected. |
| Remedy: | Replace the Main PCB with a new one. Before Main PCB replace, do the following checks. 1. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 2. Check short between 1 pin and 12 pin, and between 3 pin and 12 pin of CN6 of the SL-Relay PCB. (If shorted out, replace also the SL-Relay PCB.) 3. Check the connections between the SL-Relay PCB and the Slider PCB and then disconnect and connect the FFCs or the like. 4. Check short between 1 pin and 16 pin, and between 3 pin and 16 pin of CN1 of the Slider PCB. (If shorted out, replace also the Slider PCB.) |
| Error code: | 12e |
| Display: | ERROR 12e Head Faild[xxxx] (The details of [xxxx] are explained below this list.) |
| Description: | Abnormality of the Print head. Abnormality of the Driver of the Print head. |
| Remedy: | 1. Update F/W. 2. Initialize a parameter. 3. Disconnect and connect the FFC located between the Slider PCB and the SL-Relay PCB. 4. Replace the FFC located between the Slider PCB and the SL-Relay PCB. 5. Replace the Print Head with a new one. 6. Replace the Slider PCB with a new one. 7. Replace the SL-Relay PCB with a new one. |
| Error code: | 130 |
| Display: | Service Call 130: Error |
| Description: | Fuser Error |
| Causes: | 1) Is error message displayed? 2) Does error reoccur? |
| Remedy: | Fuser failed to reach standby temperature - hot roll |
| Error code: | 13c |
| Display: | SYSTEM HALT (*) 13c : PCB SLRY-F2 |
| Description: | SL-Relay PCB fuse (F2) disconnected. |
| Remedy: | Replace the SL-Relay PCB with a new one. Before SL-Relay PCB replace, do the following checks. 1. Check the connections between the Slider PCB and the SL-Relay PCB, and then disconnect and connect the FFCs. 2. Check short between 1 pin and 4 pin of CN1, and between 1 pin and 9 pin of CN11 of the Slider PCB. (If shorted out, replace also the Slider PCB.) |
| Error code: | 13d |
| Display: | SYSTEM HALT (*) 13d : PCB SLRY-F3 |
| Description: | SL-Relay PCB fuse (F3) disconnected. |
| Remedy: | Replace the SL-Relay PCB with a new one. Before SL-Relay PCB replace, do the following checks. 1. Check the connections between the Pump III PCB and the SL-Relay PCB, and then disconnect and connect the FFCs. 2. Check short between 1 pin and 4 pin of CN1, and between 1 pin and 9 pin of CN6 of the Pump III PCB. (If shorted out, replace also the Pump III PCB.) |
| Error code: | 13e |
| Display: | SYSTEM HALT (*) 13e : PCB STATION-F1 |
| Description: | Station PCB fuse (F1) disconnected. |
| Remedy: | 1. Replace the Station III PCB with a new one. |
| Error code: | 13f |
| Display: | SYSTEM HALT (*) 13f : PCB STATION-F2 |
| Description: | Station PCB fuse (F2) disconnected. |
| Remedy: | 1. Replace the Station III PCB with a new one. |
| Error code: | 140 |
| Display: | SVC 140 ERROR |
| Description: | Motor |
| Remedy: | DC motor accel stall - staging - replace the Staging motor. If this does not fix the problem, replace the “System board” |
| Error code: | 146 |
| Display: | ERROR 146 E-LOG SEQ |
| Description: | Motor |
| Remedy: | Autocompensator motor over speed, autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24 If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 147 |
| Display: | Service Call 147:Error |
| Description: | Motor |
| Remedy: | There is no autocompensator DC motor feedback. Replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 149 |
| Display: | ERROR 149 INK UPSTREAM GRD |
| Description: | Ink back-flow preventing process executed. When Ink is filled within Sub-tank more than Fluid level high-sensor, Guard process turning to Positive pressure and pushing back Ink is executed. After executed, this error is indicated then the system is down. |
| Error code: | 151 |
| Display: | ERROR 151 POSI.PRS KEEP OVER |
| Description: | Dusty Density Sensor The printer detects an accumulation of dust on the CTD (ADC) Sensor. |
| Causes: | • CTD (ADC) Sensor, PL5.2.19 • FSR/ADC Harness, PL5.2.28 |
| Remedy: | 1 Clean the CTD (ADC) Sensor. Does the error persist? Go to Step 2. Complete 2 Check the following for evidence of fault or damage: • Transfer Roller Assembly, PL5.1.4 • CTD (ADC) Sensor, PL5.2.19 Replace the damaged parts. Go to Step 3. 3 Check the CTD (ADC) Sensor connection. Is P/J136 connected to the harness? Go to Step 4. Reconnect the sensor. 4 Replace the CTD (ADC) Sensor. Does the error persist? Go to Step 5. Complete. 5 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J136. 2. Check continuity between J36 <=> J136. Go to Step 6. Replace the FSR/ ADC Harness. 6 Check the CTD (ADC) Sensor signal. Disconnect P/J136. Does P136-4 <=> P136-1 = 0 V? Replace the CTD (ADC) Sensor. Replace the Engine Control Board. |
| Error code: | 152 |
| Display: | ERROR 152 Main PCB V2R5 |
| Description: | Jam at Fuser: Jam F Paper did not reach the Exit Sensor on time or the Exit Sensor indicates that paper remains in the Fuser Exit Roller. |
| Causes: | • Fuser, PL5.1.1 • Exit Sensor Actuator, PL5.1.2 • Fuser Drive Assembly, PL5.2.25 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Exit Actuator and Sensor, PL5.1.2 and PL5.1.3 • Fuser Assembly, PL5.1.1 • Front Cover, PL1.1.6 • Chute Assembly In, PL5.2.1 • Transfer Roller, PL5.1.4 • Imaging Unit, PL6.1.1 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Remove the Fuser and check for broken or bent pins. Replace the parts concerned. Go to Step 3. 3 Reinstall the Fuser. Does error recur after the Fuser Assembly has been replaced? Go to Step 4. Complete 4 Test the Exit Sensor. Run the Service Diagnostics Exit Sensor Test. Does the sensor function correctly? Go to Step 7. Go to Step 5. 5 Check the Exit Sensor Signal. Insert a sheet of paper into the Fuser. Is the voltage across J361-A5 <=> J361- A6 0 V? Go to Step 7. Go to Step 6. 6 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J361 and P/J36. 2. Check continuity between J361<=>J36. Go to Step 7. Replace the FSR/ ADC Harness. 7 If possible print one sheet of paper. Does the Fuser Motor Turn? Inspect and replace defective gear(s). Go to Step 8. 8 Test the Fuser Drive Assembly. Run the Service Diagnostics Fuser Motor test. Does the Fuser Motor function correctly? Replace the Engine Control Board. Go to Step 10. 9 Check for +24 V to the Fuser Motor. Disconnect P/J521. Is there +24 V across J521-10 <=> ground? Go to Step 11. Replace the Engine Control Board. 10 Replace the Fuser Drive Assembly. Does the Fuser Motor function correctly? Complete Go to Step 11. 11 Check TNRFULL/FSR Harness continuity. 1. Disconnect P/J52 and P/J521. 2. Check continuity between J52 <=> J521. Replace the Engine Control Board. Replace the TNRFULL/FSR Harness. |
| Error code: | 153 |
| Display: | Service call 153: Error |
| Description: | Jam at Duplex: Jam D The Duplex Jam Sensor indicates that paper did not reach the sensor on time or that paper remains in the Chute Assembly Out. |
| Causes: | • Duplex Jam Sensor, PL5.4.1 • Jam Sensor Actuator, PL5.4.13 • Duplex Motor Assembly, PL5.4.5 • FRONT/DUP Harness, PL5.3.28 • Chute Assembly Out, PL5.3.1 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Duplex Motor Assembly, PL5.4.5 • JAM Sensor Actuator, PL5.4.13 • Chute Assembly Out, PL5.3.1 Are there any defects? Replace any damaged part. Go to Step 2. 2 Test the Duplex Jam Sensor. Run the Service Diagnostics Jam Sensor test. Does the sensor function correctly? Go to Step 7. Replace the Duplex Jam Sensor and Go to Step 3. 3 Check printer function. Does the printer function correctly after replacing the Duplex Jam Sensor? Complete Go to Step 4. 4 Check the Duplex Jam Sensor signal. Block the Duplex Jam Sensor. Is the voltage across J133-1 <=> J133-2 0 V? Go to Step 6. Go to Step 5. 5 Check FRONT/DUP Harness continuity. 1. Disconnect P/J133 and P/J13. 2. Check continuity between J133 <=> J13 Go to Step 6. Replace the FRONT/DUP Harness. 6 Print a Test Print in Duplex mode Does the sheet reverse in the printer? Replace the Chute Assembly Out. Go to Step 7. 7 Test the Duplex Motor. 1. Close the Interlock Switch during the test. 2. Run the Service Diagnostics Duplex Motor test. Does the Duplex Motor function correctly? Replace the Chute Assembly Out. Go to Step 8. 8 Check for +24 V to the Duplex Motor. Disconnect P/J501. Is there +24 V across P501-6 <=> ground? Go to Step 9. Replace the Engine Control Board. 9 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J501. 2. Check continuity between J13 <=> P501. Got to Step 10. Replace the FRONT/DUP Harness. 10 Replace the Duplex Motor. Does the error persist? Replace the Engine Control Board. Complete |
| Error code: | 154 |
| Display: | Service Call 154: Error |
| Description: | Jam at Registration Roller: Jam RR The Registration Sensor indicates that paper did not reach the sensor on time or that paper remains in the Registration Chute. |
| Causes: | • Registration Sensor, PL4.1.3 • Registration Sensor Actuator, PL4.1.1 • Registration Roller Assembly, PL4.2.1 |
| Remedy: | 1 Check the following for damage. • Registration Sensor Actuator, PL4.1.1 • Registration Roller Assembly, PL4.2.1 Is there any damage? Clean or replace as needed. Go to Step 2. 2 Test the Registration Sensor. Run the Service Diagnostics Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 3. 3 Check the Registration Sensor connection. Is the Registration Sensor connected to the harness? Go to Step 4. Reconnect. 4 Check all pins on the REGISNS Harness PL 4.1.4 for continuity. 1. Disconnect P/J181 and P/J18. 2. Check continuity between J181 <=> J18. Go to Step 5. Replace the Registration Sensor Harness. 5 Check the Registration Sensor signal. Block the Registration Sensor. Verify the voltage between P/J18-3 <=> P/J18-2 on the Engine Control Board is 0 VDC. Go to Step 6. Replace the Registration Sensor. 6 Test the Registration Clutch. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Registration Clutch test. Does the clutch function correctly? Go to Step 8. Go to Step 7. 7 Check the Registration Clutch resistance. Disconnect connector P/J192. Is the resistance between J192-1 <=> J192-2 less than 200ƒ¶? Go to Step 8. Replace the Registration Clutch (Part of the Registration Roller Assembly) 8 Check for +24 V to the Registration Clutch. 1. Disconnect P/J192. 2. Close the Interlock Switch while testing. Is there +24 V across P192-3 <=> ground? Replace the Registration Chute. Replace the Engine Control Board. |
| Error code: | 155 |
| Display: | Service Call 155: Error |
| Description: | Misfeed at Tray 1 (MPT): Jam T1 Paper fed from Tray 1 (MPT) did not reach the Registration Sensor on time. |
| Causes: | • Feed Roller Assembly MPT, PL5.3.20 • Interlock Switch, PL9.1.11 • Registration Sensor, PL4.1.3 • Feed Solenoid, PL5.3.9 • Registration Roller Assembly, PL4.2.1 • Main Drive Assembly, PL8.1.2 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Feed Roller Assembly MPT, PL5.3.20 • Tray 1 (MPT) • Registration Sensor, PL4.1.3 • Main Drive Assembly, PL8.1.2 Remove any foreign objects or paper debris from the paper path. Is there any damage? Replace any damaged or excessively worn parts. Go to Step 2. 2 Test the Registration Sensor. Run the Service Diagnostics Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 3. 3 Check the Registration Sensor connection. Is the Registration Sensor connected to the harness? Go to Step 4. Connect the sensor. 4 Check all pins of the REGISNR Harness PL4.1.4 for continuity. 1. Disconnect P/J181 and P/J18. 2. Check continuity between J181 <=> J18. Go to Step 5. Replace the Registration Sensor Harness. 5 Check the Registration Sensor signal. Block the Registration Sensor. Verify the voltage between P/J18-3 <=> P/J18-2 on the Engine Control Board is 0 VDC. Replace Registration Sensor. Go to Step 6. 6 If possible, print a Test Print from Tray 1 (MPT). Does the Main Motor function properly? Go to Step 16 Go to Step 7 7 Test the Main Drive Assembly. Run the Service Diagnostics Main Motor test. Does the Main Motor turn? Replace the Engine Control Board. Go to Step 8. 8 Check for +24 V to the Main Drive Motor 1. Disconnect P/J481. 2. Close the Interlock Switch while testing. Is there +24 V across J481-10 <=> J481-8? Go to Step 12. Go to Step 9. 9 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the Interlock Switch function correctly? Go to Step 11. Go to Step 10. 10 Check for +5 V to the Interlock Switch Disconnect P/J161. Is there +5 V across P161-1 <=> P161-2? Replace the LVPS. Replace the Interlock Switch. 11 Check FAN/PHD/MOT Harness continuity. 1. Disconnect P/J48 and P/J481. 2. Check continuity between J48 <=> J481 Replace Main Drive Motor Replace FAN/ PHD/MOT Harness. 12 Check Turn Roller function. 1. Perform Steps 1 ~ 3 on. 2. Open and close the front door. 3. Observe the Turn Roller. Does the Turn Roller turn while the machine is warming up? Go to Step 16. Go to Step 13. 13 Test the Turn Clutch. 1. Run the Service Diagnostics Tray 1 (MPT) Turn Clutch test. 2. Close the Interlock Switch while testing. Does the Turn Clutch function normally? Check that the Clutch doesn’t slip. Check the gears for damage. Go to Step 14. 14 Check for +24 V to the Turn Clutch. 1. Disconnect P/J191. 2. Close the Interlock Switch while testing. Is there +24 V across P191-2 <=> ground? Go to Step 15. Replace the Engine Control Board. 15 Check Turn Clutch resistance. Disconnect P/J191. Is the resistance between J191-1 <=> J191-2 less than 200Ω? Go to Step 16. Replace the Turn Clutch (Part of the Registration Roller Assembly). 16 If possible, print a Test print from Tray 1 (MPT). Check the Feed Gear operation. Does the gear function normally? Check for damage or obstructions in the paper path. Go to Step 17. 17 Test the Feed Solenoid. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Tray 1 (MPT) Feed Solenoid test. Does the Feed Solenoid function normally? Check that the Feed Solenoid spring and stopper disengage correctly. Go to Step 18. 18 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J132 and P/J13. 2. Check continuity between J13 <=> P132. Go to Step 19. Replace the FRONT/DUP Harness Assembly. 19 Check Feed Solenoid resistance. Disconnect connector P/J132. Is the resistance between J132-1 <=> J132-2 less than 100Ω? Replace the Engine Control Board. Replace the Feed Solenoid. |
| Error code: | 156 |
| Display: | ERROR 156 Main PCB V5B |
| Description: | Misfeed at Tray 2: Jam T2 Paper fed from Tray 2 did not reach the Registration Sensor on time. |
| Causes: | • Feed Rollers, PL3.3.18 • Interlock Switch, PL9.1.11 • Registration Sensor, PL4.1.3 • Registration Roller PL4.2.1 • Main Drive Assembly, PL8.1.2 • Tray 2 Paper Pick Assembly, PL3.3.1 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Feed Rollers, PL3.3.18 • Paper Pick Assembly, PL3.3.1 • Tray 2, PL2.1.1 • Registration Sensor, PL4.1.3 • Main Drive Assembly, PL8.1.2 Replace any damaged or excessively worn parts. Go to Step 2. 2 Test the Registration Sensor. Run the Service Diagnostics Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 3. 3 Check the Registration Sensor connection. Is the Registration Sensor connected to the harness? Go to Step 4. Connect the sensor. 4 Check all pins on the REGISNS Harness PL4.1.4 for continuity. 1. Disconnect P/J181 and P/J18. 2. Check continuity between J181 <=> J18 Go to Step 5. Replace the Registration Sensor Harness. 5 Check the Registration Sensor signal. Block the Registration Sensor. Is the voltage across P/J18-3 <=> P/J18-2 0 V? Replace Registration Sensor. Go to Step 6. 6 If possible, print a Test Print from Tray 1 (MPT). Does the Main Motor function properly? Go to Step 16. Go to Step 7. 7 Test the Main Drive Assembly. Run the Service Diagnostics Main Motor test. Does the Main Motor turn? Replace the Engine Control Board. Go to Step 8. 8 Check for +24 V to the Main Drive Motor 1. Disconnect P/J481. 2. Close the Interlock Switch while testing. Is there +24 V across J481-10 <=> J481-8? Go to Step 12. Go to Step 9. 9 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the Interlock Switch function correctly? Go to Step 11. Replace the parts concerned. 10 Check for +5 V to the Interlock Switch Disconnect P/J161. Is there +5 V across P161-1 <=> P161-2? Replace the LVPS. Replace the Interlock Switch. 11 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J481. 2. Check continuity between J48 <=> J481. Replace Main Drive Motor Replace FAN/ PHD/MOT Harness. 12 Check Turn Roller function. 1. Perform Steps 1 through 3 on. 2. Open and close the front door. 3. Observe the Turn Roller. Does the Turn Roller turn while the machine is warming up? Go to Step 16. Go to Step 13 13 Test the Turn Clutch. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Tray 1 (MPT) Turn Clutch test. Does the Turn Clutch function normally? Check that the Clutch doesn’t slip. Check the gears for damage. Go to Step 14. 14 Check for +24 V to the Turn Clutch. 1. Disconnect P/J191. 2. Close the Interlock Switch while testing. Is there +24 V across P191-2 <=> ground? Go to Step 15. Replace the Engine Control Board. 15 Check all pins on the FRONTCLH Harness PL4.1.21 for continuity. 1. Disconnect P/J191 and P/J19. 2. Check continuity between J19 <=> P191. Go to Step 16. Replace the FRONTCLH Harness Assembly. 16 Check Turn Clutch resistance. Disconnect P/J191. Is the resistance between J191-1 <=> J191-2 less than 200Ω? Replace the Engine Control Board. Replace the Turn Clutch (Part of the Registration Roller Assembly). 17 Check the Tray 2 Feed Solenoid. If possible, print a Test print from Tray 2. Does the Feed Gear operate correctly? Replace any damaged or excessively worn parts. Go to Step 18. 18 Test the Tray 2 Feed Solenoid. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Tray 2 Feed Solenoid test. Does the Feed Solenoid function normally? Check the Solenoid Feed spring and stopper. Go to Step 19. 19 Check all pins on the FDR Harness PL3.3.22 for continuity. 1. Disconnect P/J474 and P/J47. 2. Check continuity between J47 <=> P474. Go to Step 20. Replace the FDR Harness. 20 Check Feed Solenoid resistance. Disconnect connector P/J474. Is the resistance between J474-1 <=> J474-2 less than 100Ω? Replace the Engine Control Board. Replace Tray 2 Feed Solenoid (Part of the Tray 2 Paper Pick Assembly). |
| Error code: | 157 |
| Display: | ERROR 157 Main PCB VTT |
| Description: | Misfeed at Tray 3: Jam T3 Paper being fed from either the 550-Sheet Feeder or the top tray of the 1100-Sheet Feeder did not reach the Registration Sensor on time. |
| Causes: | For 550-Sheet Feeder: • Feed Rollers, PL11.3.20 • Paper Pick Assembly, PL11.3.1 • Drive Assembly, PL11.3.15 • OPFDR Harness, PL11.3.24 • OPTFDR Board, PL11.1.10 • OPFPLG Harness, PL11.1.13 For 1100-Sheet Feeder: • Feed Rollers, PL12.4.19 • Paper Pick Assembly, PL12.4.1 • Drive Assembly, PL12.3.9 • OPFDR Harness, PL12.3.7 • OPTFDR Board, PL12.3.3 • OPFREC2 Harness, PL12.3.1 |
| Remedy: | 1 Check the printer paper path. Does paper feed correctly from Tray 2? Go to Step 2. See "Misfeed at Tray 2 Jam T2". 2 If possible, print a Test print from Tray 3. Does the Drive Assembly operate? Go to Step 9. Go to Step 3. 3 Test the Drive Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics HCF/LTA Motor test. Does the Drive Motor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check for +24 V to the Drive Motor. 1. Disconnect P/J82. 2. Close the Interlock Switch while testing. Is the voltage between P82-1 <=> ground on the OPTFDR Board +24 V? Go to Step 7. Go to Step 5. 5 Check for +24 V to the OPTFDR 1 Board. 1. Disconnect P/J83. 2. Close the Interlock Switch while testing. Is the voltage between P83-3 <=> P83-4 on the OPTFDR Board +24 V? Replace the OPTFDR Board. Go to Step 6 6 Check the Feeder Interface continuity. 1. Disconnect P/J171 or P/J172 and P/J83. 2. Check continuity between J171/2 <=> P83 Go to Step 7. Replace the OPFREC Harness. 7 Replace the Drive Assembly. Does the error persist? Go to Step 8. Complete 8 Perform Steps 1 through 3. 1. Open and close the front door. 2. Observe the Turn Roller. Does the Turn Roller turn while the printer is warming up? Go to Step 13. Go to Step 9. 9 Test the Turn Clutch. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Turn Clutch test. Does the Tray 3 Turn Clutch function correctly? Check the Clutch for slipping or the gear for damage. Go to Step 10. 10 Check for +24 V to the Turn Clutch. 1. Disconnect P/J825 2. Close the Interlock Switch while testing. Is there +24 V across P825-2 <+>ground? Go to Step 11. Replace the OPTFDR 1 Board. 11 Check all pins on the OPFDR Harness PL11.3.24 for continuity. 1. Disconnect P/J85 and P/J825. 2. Check continuity between J85 <=> P825. Go to Step 12. Replace the OPFDR Harness. 12 Check Turn Clutch resistance. Disconnect P/J825. Is the resistance between J825-1 <=> J825-2 less than 200Ω? Go to Step 13. Replace the Turn Clutch (Part of the Paper Pick Assembly). 13 Check the Feed Gear. Does the Feed Gear in the Paper Pick Assembly turn when printing a sheet of paper? Check the Feed Solenoid for damage. Go to Step 14. 14 Test the Feed Solenoid. Run the Service Diagnostics Feed Solenoid test. Does the solenoid function correctly? Check the feed solenoid stopper and replace if necessary. Go to Step 15. 15 Check for +24 V to the Feed Solenoid. 1. Disconnect P/J824 2. Close the Interlock Switch while testing. Is there +24 V across P824-2 <=>ground? Go to Step 17. Go to Step 16. 16 Check all pins on the OPFDR Harness PL11.3.24 for continuity. 1. Disconnect P/J85 and P/J824. 2. Check continuity between J85 <=> P824 Go to Step 17. Replace the OPFDR Harness. 17 Test the Feed Solenoid resistance. Disconnect P/J824. Is J824-1 <=> J824-2 less than 100Ω? Go to Step 17. Replace the Feed Solenoid (Part of the Paper Pick Assembly). 18 Check all pins on the OPFPLG Harness PL3.2.11 for continuity. 1. Disconnect P/J171 and P/J17. 2. Check continuity between P171 <=> J17. Replace the Engine Control Board. Replace the OPFPLG Harness. |
| Error code: | 158 |
| Display: | ERROR 158 Main PCB V352 |
| Description: | Misfeed at Tray 4: Jam T4 Paper being fed from the 1100-Sheet Feeder did not reach the Registration Sensor on time. |
| Causes: | • Feed Rollers, PL12.5.18 • Paper Pick Assembly, PL12.5.1 • Drive Assembly, PL12.3.9 • OPFDR Harness, PL12.3.7 • OPTFDR Board, PL12.3.3 • OPFREC2 Harness, PL12.3 |
| Remedy: | 1 Check the printer paper path. Does paper feed correctly from Tray 2? Go to Step 2. See "Misfeed at Tray 2 Jam T2". 2 If possible, print a Test print from Tray 4. Does the Drive Assembly operate? Go to Step 9. Go to Step 3. 3 Test the Drive Assembly. Run the Service Diagnostics HCF/LTA Motor test. Does the Drive Motor function correctly? Replace the Engine Control Board, page 8-107. Go to Step 4. 4 Check for +24 V to the Drive Motor. 1. Disconnect P/J82. 2. Close the Interlock Switch while testing. Is the voltage between P82-1 <=> ground on the Upper Circuit Board HCF +24 V? Go to Step 7. Go to Step 5. 5 Check for +24 V to the OPTFDR Board. 1. Disconnect P/J83. 2. Close the Interlock Switch while testing. Is the voltage between P83-3 <=> P83-4 on the Lower Feeder Circuit Board +24 V? Replace the Lower Circuit Board HCF. Go to Step 6 6 Check all pins on the OPFREC2 Harness PL12.3.1 for continuity. 1. Disconnect P/J172 and P/J83. 2. Check continuity between J172 <=> P83. Go to Step 7. Replace the OPFREC2 Harness. 7 Replace the Drive Assembly. Does the error persist? Go to Step 8. Complete 8 Perform Steps 1 through 3. Open and close the front door. Observe the Turn Roller. Does the Turn Roller turn while the printer is warming up? Go to Step 13. Go to Step 9. 9 Test the Turn Clutch. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Turn Clutch test. Does the Tray 4 Turn Clutch function correctly? Check the Clutch for slipping or the gear for damage. Go to Step 10. 10 Check for +24 V to the Turn Clutch. 1. Disconnect P/J825 2. Close the Interlock Switch while testing. Is there +24 V across P85-2 <+>ground? Go to Step 11. Replace the Circuit Board HCF. 11 Check all pins on the OPFDR2 Harness PL12.3.7 for continuity. 1. Disconnect P/J85 and P/J825. 2. Check continuity between J85 <=> P825. Go to Step 12. Replace the OPFDR2 Harness. 12 Check Turn Clutch resistance. Disconnect P/J825. Is the resistance between J825-1 <=> J825-2 less than 200Ω? Go to Step 13. Replace the Turn Clutch (Part of the Paper Pick Assembly). 13 Check the Feed Gear. Does the Feed Gear in the Paper Pick Assembly turn when printing a sheet of paper? Check the Feed Solenoid for damage. Go to Step 14. 14 Test the Feed Solenoid. Run the Service Diagnostics Feed Solenoid test. Does the solenoid function correctly? Check the feed solenoid stopper and replace if necessary. Go to Step 15. 15 Check for +24 V to the Feed Solenoid. 1. Disconnect P/J824 2. Close the Interlock Switch while testing. Is there +24 V across P824-2 <+>ground? Go to Step 17. Go to Step 16. 16 Check all pins on the OPFDR Harness PL12.3.7 for continuity. 1. Disconnect P/J85 and P/J824. 2. Check continuity between J85 <=> P824. Go to Step 17. Replace the OPFDR Harness. 17 Test the Feed Solenoid resistance. Disconnect P/J824. Is J824-1 <=> J824-2 less than 100Ω? Go to Step 17. Replace the Feed Solenoid (Part of the Paper Pick Assembly). 18 Check all pins on the OPFPLG Harness PL3.2.11 for continuity. 1. Disconnect P/J171 and P/J17. 2. Check continuity between P171 <=> J17. Replace the Engine Control Board. Replace the OPFPLG Harness. |
| Error code: | 159 |
| Display: | SYSTEM HALT (*) 159 : PCB SLDR-F1 |
| Description: | Misfeed at Tray 5: Jam T5 Paper being fed from the 1100-Sheet Feeder did not reach the Registration Sensor on time. |
| Causes: | • Feed Rollers, PL12.5.18 • Paper Pick Assembly, PL12.5.1 • Drive Assembly, PL12.3.9 • OPFDR2 Harness, PL12.3.7 • OPTFDR Board, PL12.3.3 • OPFREC2 Harness, PL12.3.1 |
| Remedy: | 1 Check the printer paper path. Does paper feed correctly from Tray 2? Go to Step 2. See "Misfeed at Tray 2 Jam T2". 2 If possible, print a Test print from Tray 5. Does the Drive Assembly operate? Go to Step 9. Go to Step 3. 3 Test the Drive Assembly. Run the Service Diagnostics HCF/LTA Motor test. Does the Drive Motor function correctly? Replace the Engine Control Board, page 8-107. Go to Step 4. 4 Check for +24 V to the Drive Motor. 1. Disconnect P/J82. 2. Close the Interlock Switch while testing. Is the voltage between P82-1 <=> ground on the Upper Circuit Board HCF +24 V? Go to Step 7. Go to Step 5. 5 Check for +24 V to the OPTFDR Board. 1. Disconnect P/J83. 2. Close the Interlock Switch while testing. Is the voltage between P83-3 <=> P83-4 on the Lower Feeder Circuit Board +24 V? Replace the Lower Circuit Board HCF. Go to Step 6 6 Check all pins on the OPFREC2 Harness PL12.3.1 for continuity. 1. Disconnect P/J172 and P/J83. 2. Check continuity between J172 <=> P83. Go to Step 7. Replace the OPFREC2 Harness. 7 Replace the Drive Assembly. Does the error persist? Go to Step 8. Complete 8 Check the Turn Roller. 1. Perform Steps 1 through 3. Open and close the front door. 2. Observe the Turn Roller. Does the Turn Roller turn while the printer is warming up? Go to Step 13. Go to Step 9. 9 Test the Turn Clutch. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Turn Clutch test. Does the Tray 4 Turn Clutch function correctly? Check the Clutch for slipping or the gear for damage. Go to Step 10. 10 Check for +24 V to the Turn Clutch. 1. Disconnect P/J825 2. Close the Interlock Switch while testing. Is there +24 V across P85-2 <+>ground? Go to Step 11. Replace the Circuit Board HCF. 11 Check all pins on the OPFDR2 Harness PL12.3.7 for continuity. 1. Disconnect P/J85 and P/J825. 2. Check continuity between J85 <=> P825. Go to Step 12. Replace the OPFDR2 Harness. 12 Check Turn Clutch resistance. Disconnect P/J825. Is the resistance between J825-1 <=> J825-2 less than 200Ω? Go to Step 13. Replace the Turn Clutch (Part of the Paper Pick Assembly). 13 Check the Feed Gear. Does the Feed Gear in the Paper Pick Assembly turn when printing a sheet of paper? Check the Feed Solenoid for damage. Go to Step 14. 14 Test the Feed Solenoid. Run the Service Diagnostics Feed Solenoid test. Does the solenoid function correctly? Check the feed solenoid stopper and replace if necessary. Go to Step 15. 15 Check for +24 V to the Feed Solenoid. 1. Disconnect P/J824 2. Close the Interlock Switch while testing. Is there +24 V across P824-2 <+>ground? Go to Step 17. Go to Step 16. 16 Check all pins on the OPFDR Harness PL11.3.24 for continuity. 1. Disconnect P/J85 and P/J824. 2. Check continuity between J85 <=> P824. Go to Step 17. Replace the OPFDR Harness. 17 Test the Feed Solenoid resistance. Disconnect P/J824. Is J824-1 <=> J824-2 less than 100Ω? Go to Step 17. Replace the Feed Solenoid (Part of the Paper Pick Assembly). 18 Check all pins on the OPFPLG Harness PL3.2.11 for continuity. 1. Disconnect P/J171 and P/J17. 2. Check continuity between P171 <=> J17. Replace the Engine Control Board. Replace the OPFPLG Harness. |
| Error code: | 15a |
| Display: | SYSTEM HALT (*) 15a : MAIN FPC-1 |
| Description: | 30pinFPC1 of Main PCB connect error |
| Remedy: | 1. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs. 2. Replace the FFCs of the above routes. 3. Replace the SL-Relay PCB with a new one. 4. Replace the Main PCB with a new one. |
| Error code: | 15f |
| Display: | ERROR 15f HEAD DRIVE HOT |
| Description: | COM driver becomes the high temperature. |
| Remedy: | 1. Confirm movement of Slider Relay Cooling Fan. 2. Disconnect and connect the FFC located between the Slider PCB and the SL-Relay PCB. 3. Replace the SL-Relay PCB with a new one. 4. Replace the FFC located between the Slider PCB and the SL-Relay PCB 5. Replace the Print Head with a new one. 6. Replace the Slider PCB with a new one. |
| Error code: | 160 |
| Display: | SVC 160 ERROR |
| Description: | Tray and Media Errors When a tray is pulled out that prevents printing during a print job, an error condition exists.When a tray is pulled out while no job is printing or that does not prevent printing during a print job, a warning condition exists. |
| Causes: | • Paper Size Switch, PL3.2.5 • Paper Tray, PL2.1.1 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Tray 2 Paper Size Switch, PL3.2.5 • Tray 2 Paper Size Switch Actuators, PL2.1.10 • Paper Tray, PL2.1.1 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Test the Tray 2 Paper Size Switches. Run the Service Diagnostics Paper Size Switch test. Use the table on. Do the switches function correctly? Replace the Engine Control Board. Go to Step 3. 3 Check the Paper Size Switch signals. 1. Disconnect P/J47. 2. Verify +3.3 V on pins P/J47-1 <=> P47-3 P/J47-2 <=> P47-3 P/J47-4 <=> P47-3 Is there +3.3 V when actuated? Go to Step 4 Replace the Paper Size Switch. 4 Check all pins on the FDR Harness for continuity. 1. Disconnect P/J47 and P/J471. 2. Check continuity between J47 <=> J471. Replace the Engine Control Board. Replace the FDR Harness. |
| Error code: | 161 |
| Display: | SYSTEM HALT (*) 161 : PCB MAIN-F6 |
| Description: | IPU Error At power on, or when the machine returns from an energy save mode, the self-diagnostic program returned an IPU error. |
| Causes: | • IPU defective • Connection between SBU and IPU is loose, broken, or defective |
| Error code: | 16e |
| Display: | ERROR 16e Main PCB V3R3B |
| Description: | Main board 3.3VÇa power supply is abnormal. |
| Remedy: | 1. Replace the Main PCB with a new one. |
| Error code: | 170 |
| Display: | Inspection is required. 170:Error |
| Description: | Motor |
| Causes: | Does this error recur? |
| Remedy: | Mirror motor lost lock - black - go to “Printhead diagnostics” on page 3-1. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” on page 3-1. |
| Error code: | 171 |
| Display: | Inspection is required. 171:Error |
| Description: | Motor |
| Causes: | Does this error recur? |
| Remedy: | Mirror motor lock not achieved - cyan - go to “Printhead diagnostics” on page 3-1. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” on page 3-1. |
| Error code: | 172 |
| Display: | Inspection is required. 172:Error |
| Description: | Motor |
| Causes: | Does this error recur? |
| Remedy: | Mirror motor lost lock - cyan - go to “Printhead diagnostics” on page 3-1. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” on page 3-1. |
| Error code: | 201 |
| Display: | ERROR 201 COMMAND |
| Description: | PU F/W Flash write error (Reserved) |
| Causes: | • Defective polygon motor • Defective harness |
| Remedy: | 1. Connect the cable correctly. 2. Replace the engine control board. 3. Replace the laser scanning unit. 4. Check or replace the cable. |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 303 |
| Display: | SYSTEM HALT (*) 303 : PCB MAIN ET |
| Description: | AC charge output error [Y] The measured voltage is not proper when IOB measures the charge output for each color. |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 304 |
| Display: | ERROR 304 USB INIT ERR |
| Description: | Charge AC bias error [K] The charge current less than 200 mkA is detected. |
| Causes: | Defective charge roller. Defective connectors. Disconnected harness. Defective high voltage power 1. |
| Remedy: | 1. Check the connectors. 2. Replace the PCU for black. 3. Replace the drum positioning plate. |
| Error code: | 305 |
| Display: | ERROR 305 USB TIME OUT |
| Description: | Charge Corona Wire Cleaner Error The charge wire cleaner did not: (1) come from the home position within 5 s, or (2) did return to the home position within 3.75 s due to wire cleaner overload. |
| Causes: | • Cleaner unit blocked or damaged • Until replacement parts become available, set SP2804 to "0" to disable the charge-corona cleaning function so the machine can operate. |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 403 |
| Display: | ERROR 403 X CURRENT |
| Description: | Transfer belt position sensor error The transfer belt position sensor did not activate after the transfer belt contact clutch was switched on twice and rotated once. |
| Causes: | • Main motor malfunction • Transfer belt contact clutch defective • Transfer belt position sensor harness or connector loose, broken, defective • Transfer belt position sensor defective |
| Remedy: | 1. Check if there is no error on the print data. (Check if the same error occurs on other data?) 2. Check if it moves to the X-direction smoothly in the power-off condition. 3. Make sure no torsion on the X-bar or Y-bar. 4. Check if there is no trouble on the Timing Belt. 5. Check if there is no trouble on the Motor Cable. (disconnecting, burnout, or the like) 6. Check the FFC between each PCB and Shortconnectors connected on the PCB. 7. Replace the X-axis Motor with a new one. |
| Error code: | 404 |
| Display: | ERROR 404 Y CURRENT |
| Description: | Transmitter sent NSS (or DCS) followed by TCF three times, but the receiver did not respond. (CFR or FTT is usually returned) |
| Causes: | Receiver is defective. (Modem, MJR PCB, etc.) SC PCB or MJR PCB are defective. Receiver disconnects line during first NSS (or DCS) is transmitted. |
| Remedy: | 1. Check if there is no error on the print data. (Check if the same error occurs on other data?) 2. Check if it moves to the Y-direction smoothly in the power-off condition. 3. Check if there is no trouble on the Timing Belt. 4. Check if there is no trouble on the Motor Cable. (disconnecting, burnout, or the like) 5. Check the FFC between each PCB and Shortconnectors connected on the PCB. 6. Replace the Y-axis motor with a new one. |
| Error code: | 406 |
| Display: | SYSTEM HALT (*) 406 : WIPER ORG |
| Description: | ID Sensor Pattern Edge Detection Error The ID sensor pattern check could not detect the correct voltage on the ID sensor pattern (below 2.5V) within 0.6 sec. |
| Causes: | • ID sensor dirty • ID sensor harness loose, damaged, defective • ID sensor connector defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 40b |
| Display: | SYSTEM HALT (*) 40b : UN MAGNETIC |
| Description: | DC motor is driving without excited |
| Remedy: | 1.Update F/W. 2. Upload the parameter and initialize parameter with #PARAMETER. 3. Replace the Main PCB with a new one. |
| Error code: | 420 |
| Display: | ERROR 420 Z POSITION |
| Description: | Potential sensor error: Vd Adjustment K. The drum potential sensor detects 150V or more on the drum (Vd) for 0.7 msec. when the high voltage charge is supplied to the drum for the initial sampling before exposure. |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Drum worn |
| Remedy: | 1. Clean or replace the drum potential sensor. 2. Replace the drum unit. |
| Error code: | 421 |
| Display: | ERROR 421 !CHECK FILTER |
| Description: | Potential sensor error: Vd Adjustment C. The drum potential sensor detects 150V or more on the drum (Vd) for 0.7 msec. when the high voltage charge is supplied to the drum for the initial sampling before exposure. |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Drum worn |
| Remedy: | 1. Clean or replace the drum potential sensor. 2. Replace the drum unit. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 505 |
| Display: | ERROR 505 !WORK High |
| Description: | HCF must be rebuilt |
| Causes: | The 2nd tray of D580 when D579 and D580 are attached, or D631 when D580 and D631 are attached. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 509 |
| Display: | SYSTEM HALT (*) 509 : HDC POSCNT |
| Description: | Replace red developer |
| Causes: | • Poor connection or defective tray 5 or 6 lift motor • Poor connection or defective tray 5 or 6 lift sensor • Remaining paper or another obstruction has stopped the tray and motor. • Pick-up solenoid 5 or 6 connector is loose. • Pick-up solenoid 5 or 6 is blocked by an obstruction. |
| Remedy: | 1. Replace the tray 5 or 6 lift motor. 2. Replace the tray 5 or 6 lift sensor. 3. Check or clear obstacles around pick-up solenoid 5 or 6. |
| Error code: | 50a |
| Display: | ERROR 50a Y ORIGIN |
| Description: | Y-origin error (Origin of Y-axis can not be detected) |
| Remedy: | 1. Execute and confirm [#TEST]->[SENSOR TEST] - >[Y-ORG].(Confirm that the ON/OFF display is switched by moving the carriage left and right.) 2. [Execute [#TEST]->[CHECK ENCODER]. 3. Check in manual if the Head Assy. (carriage) moves left and right smoothly. 4. Check the connector connection of Y-origin Sensor and Linear Encoder. 5. Replace the Y-origin Sensor or Linear Encoder with a new one. 6. Check the assembly and connector connection of Yaxis Motor. 7. Replace the Y-axis Motor with a new one. 8. Replace the Slider PCB with a new one. 9. Replace the SL-Relay PCB with a new one. 10. Replace the Main PCB with a new one. |
| Error code: | 50f |
| Display: | ERROR 50f L-SCALE BLACK |
| Description: | Liner Scale error |
| Remedy: | 1. Check the assembly position of Linear Scale and Encoder PCB Assy.. 2. Check Linear Scale (scratches or dirtiness or so.) 3. Replace the Linear Scale with a new one. 4. Replace the Encoder PCB Assy. with a new one. |
| Error code: | 510 |
| Display: | SYSTEM HALT (*) 510 : X ORGIN |
| Description: | Replace green developer |
| Causes: | • Tray lift motor defective or connector disconnected • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Remedy: | 1. Check the harness connection or replace it. 2. Replace the bypass tray lift motor. 3. Replace the bypass upper limit sensor. 4. Replace the bypass lower limit sensor. 5. Check or clear obstacles around the bypass pick-up solenoid. |
| Error code: | 511 |
| Display: | SYSTEM HALT (*) 511 : Z ORGIN |
| Description: | A3 LCT exit roller contact motor 1 error. One of the following conditions is detected in the A3 LCT. • The LCT exit roller sensor is not activated within 225 pulses after the LCT exit roller contact motor has turned on at its initialization. • The LCT exit roller sensor detects for 25 pulses even after the LCT exit roller has moved away from its home position. • The LCT exit roller sensor does not detect within 25 pulses after the LCT exit roller has moved back to its home position. |
| Causes: | • Poor connection or defective LCT exit roller contact motor • Poor connection or defective LCT exit roller sensor |
| Remedy: | 1. Check the harness connection. 2. Replace the LCT exit roller contact motor. 3. Replace the LCT exit roller sensor. |
| Error code: | 601 |
| Display: | ERROR 601 INK NEAREND |
| Description: | Communication Error between BCU and MCU (D016/D097 only) One or more of the following occurred: • The BCU cannot communicate with the MCU (LCT-MF) within 100 ms after power on after 3 tries. • A BREAK signal was detected after connection between the BCU and MCU. • After a communication error, three tries to communicate with the MCU failed. |
| Causes: | • Poor connection between BCU and MCU • BCU defective • MCU defective |
| Remedy: | 1. Check or replace the harness between the BCU and MCU. 2. Replace the BCU. 3. Replace the MCU in the LCT-MF. |
| Error code: | 602 |
| Display: | ERROR 602 INK END |
| Description: | Communication problem between main board and high voltage unit |
| Remedy: | (If this message appears when a new cartridge or a cartridge with enough ink is set) 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [INK NEND1](The number meets the cartridge No.). 2. Check the peripheral and the assembly of the End Sensor. 3. Check the connection of the Presence Sensor and the End Sensor. 4. Replace the Cartridge with a new one. 5. Replace the Presence / Near End Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one. |
| Error code: | 603 |
| Display: | ERROR 603 NO CARTRDG |
| Description: | Main board problem |
| Remedy: | (When the message is still displayed even after a Ink Cartridge is charged;) 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [INK1](The number meets the cartridge No.).. 2. Check the peripheral and the assembly of the Presence Sensor. 3. Check the connection of the Presence Sensor and the End Sensor 4. .Replace the Cartridge with a new one 5. Replace the Presence/Near End Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one. (Refer to 3.3. |
| Error code: | 605 |
| Display: | ERROR 605 !CLEANING WIPER |
| Description: | Communication Error Between Controller and ECU One of these problems occurred: • Serial communication error • Serial data overflowed in the receive data buffer. |
| Causes: | • Replace the MCU. |
| Remedy: | 1. Execute [FUNCTION MAINTENANCE]- >[STATION]->[MENT:WIPER CLEANING] to clean the wiper. 2. Replace the Main PCB with a new one. |
| Error code: | 606 |
| Display: | ERROR 606 WRONG CARTRIDGE |
| Description: | The IC chip of the ink cartridge is not read properly. |
| Remedy: | (If this message appears when a correct cartridge is set) 1. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 2. Check the connection of the ID Contact PCB. 3. Replace the Cartridge with a new one 4. Replace the ID Contact PCB Assy. with a new one. 5. Replace the SL- |
| Error code: | 607 |
| Display: | ERROR 607 CAP CLEANING |
| Description: | Warning for cleaning around the cap (A specified number of flushing on the cap exceeded.) 1),Capcleaning counter (Ink parameter 1 No04 CapClean) Counter is cleared when the following is executed: [FUNCTION MAINTENANCE]- >[STATION]->[MENT:CARRIAGE OUT] 2),Specified number of the Capcleaning : warning level 100x2^(Ink parameter 2 No.66 Cap.LM -1) |
| Remedy: | 1. Clean the cap. (If this message appears after cleaning the cap) 2. Replace the Main PCB with a new one. |
| Error code: | 608 |
| Display: | ERROR 608 CARTRIDGE |
| Description: | Ink is tried to fill with unusable cartridge installed. |
| Remedy: | 1. Check the type of the ink cartridge. Execute the followings if the type of the ink cartridge is correct. 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4. Replace the Cartridge with a new one 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the SL-Relay PCB with a new one. |
| Error code: | 60b |
| Display: | ERROR 60b WIPER BOTTLE |
| Description: | Wiper bottle warning A great deal of ink is in the Wiper Bottle. Displayed when the Wiper Nozzle Suction Pump exceeds the 2,500 times [Fixed]. Wiper Pump suction times: Ink parameter 1 No47 [Wipe Pump ] |
| Remedy: | 1. Select [FUNCTION MAINTENANCE]->[STATION]- >[MENT:WIPER BOTTLE] and dispose of ink in the Wiper Bottle. |
| Error code: | 60c |
| Display: | ERROR 60c INK TYPE |
| Description: | Type of inserted Ink Cartridge is different. |
| Remedy: | 1. Check the type of the ink cartridge. Execute the followings if the type of the ink cartridge is correct. 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4. Replace the Cartridge with a new one 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the SL-Relay PCB with a new one. |
| Error code: | 60d |
| Display: | ERROR 60d REMAIN INK |
| Description: | Remaining ink is not enough to execute cleaning or to fill ink. |
| Remedy: | Replace the Cartridge with a new one |
| Error code: | 60e |
| Display: | ERROR 60e NOT COMPLETE FUP |
| Description: | Ink is not filled into some heads. |
| Remedy: | Fill ink into unfilled heads. |
| Error code: | 60f |
| Display: | ERROR 60f Expiration |
| Description: | Some ink cartridges are expired. |
| Remedy: | 1. Check the expiration date of the ink. (If this message appears when a correct cartridge is set) 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4. Replace the Cartridge with a new one. 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the SL-Relay PCB with a new one. |
| Error code: | 610 |
| Display: | ERROR 610 NOT FILLUP |
| Description: | Mechanical counter error: Bk This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 611 |
| Display: | ERROR 611 Case Weight |
| Description: | Mechanical counter error: FC This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 612 |
| Display: | ERROR 612 INK LVL LOW |
| Description: | BICU - ADF communication/command abnormal A command that cannot be executed was sent from the main machine to the ADF. |
| Causes: | • A software error, result of an abnormal procedure. |
| Remedy: | Enter the cartridge weight from "CART WEIGHT" menu of "SET UP". |
| Error code: | 613 |
| Display: | ERROR 613 INK LVL END |
| Description: | Remaining amount of ink became none. |
| Remedy: | • If ink remains, enter the cartridge weight from "CART WEIGHT" menu of "SET UP". • If ink does not remain, replace it with a new cartridge. |
| Error code: | 614 |
| Display: | ERROR 614 Preservation Failure |
| Description: | Remaining amount of ink was failed to be written. |
| Remedy: | 1. Pull the cartridge out and then insert it to write it again. 2. If the error cannot be solved, replace it with a new cartridge. |
| Error code: | 615 |
| Display: | ERROR 615 Cartridge Weight |
| Description: | The cartridge weight was not entered. |
| Remedy: | Enter the cartridge weight. |
| Error code: | 702 |
| Display: | ERROR 702 THERMISTOR |
| Description: | ADF Feed-In Motor Error (D016/D097 only) While the feed motor is operating, the encoder pulse signal is not received within the specified time, or the paper size length encoder signal cannot be detected within the specified time (the encoder is built into the feed-in motor). |
| Causes: | • Feed-in motor connector, harness loose, broken, defective • Paper length sensor connector, harness loose, broken, defective • Feed-in motor defective • Paper length sensor or encoder is defective • ADF main control board defective |
| Remedy: | 1. Check the harness connections. 2. Replace the feed-in motor. 3. Replace the paper length sensor. 4. Replace the main board of the ADF. |
| Error code: | 705 |
| Display: | ERROR 705 WATER LACK |
| Description: | ADF Original Table Lift Malfunction (D016/D097 only) One of the following conditions was detected. • The bottom plate position sensor did not activate when the bottom plate motor lifted the original table. • The bottom plate HP sensor did not activate when the bottom plate motor lowered the original table. |
| Causes: | • Bottom plate position sensor defective • Bottom plate HP sensor defective • Bottom plate motor defective • ADF main control board defective |
| Remedy: | 1. Replace the bottom plate position sensor. 2. Replace the bottom plate HP sensor. 3. Replace the bottom plate motor 4. Replace the ADF main control board. |
| Error code: | 706 |
| Display: | ERROR 706 UV UNIT OVER HEAT |
| Description: | Temperature in the UV unit is above its specification. |
| Remedy: | 1. Check connection and operation of the radiator fan and the UV unit fan. 2. Check the operation of the water cooling pump. 3. Check water level of the cooling water buffer tank and a path of the cooling water. 4. Check the connection of connector of the LED UV UNIT Assy and the Slider PCB. 5. Replace the LED UV UNIT Assy with a new one. 6. Replace the Slider PCB with a new one. 7. Replace the SL-Relay PCB with a new one. |
| Error code: | 707 |
| Display: | ERROR 707 !HD HEATER BRK |
| Description: | Is the heater of the head disconnected? (The temperature does not rise after heating for over a certain period of time.) |
| Remedy: | 1. Check the room temperature is not too low. 2. Replace the Print Head with a new one. 3. Replace the Slider PCB with a new one. |
| Error code: | 708 |
| Display: | ERROR 708 UV THERMISTOR BRK |
| Description: | DF fan error DF fan motor lock signal is detected after the original transportation has finished. |
| Causes: | Turn the machine off and on. |
| Error code: | 70a |
| Display: | ERROR 70a LED UV CURRENT |
| Description: | The LED UV unit has been broken. Or, the detected current is abnormal. |
| Remedy: | 1. Replace the LEDUVx2-DRIVE PDB Assy with a new one. 2. Replace the LEDUV Irradiation Assy with a new one. |
| Error code: | 801 |
| Display: | SYSTEM HALT (*) 801 : (C)OPCODE |
| Description: | Video output error (Y) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 802 |
| Display: | SYSTEM HALT (*) 802 : (C)SLOT |
| Description: | Video output error (M) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 803 |
| Display: | SYSTEM HALT (*) 803 : (C)CPU ADDR |
| Description: | Video output error (C) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 804 |
| Display: | SYSTEM HALT (*) 804 : (C)DMA ADDR |
| Description: | Startup without video input end (K) A video transmission was requested from the scanner, but the scanner did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 805 |
| Display: | SYSTEM HALT (*) 805 : (C)ZERO DIV |
| Description: | Startup without video input end error (Y) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 806 |
| Display: | SYSTEM HALT (*) 806 : FW/SIO bit |
| Description: | Startup without video input end error (M) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 807 |
| Display: | SYSTEM HALT (*) 807 : FW/SIO wbsy |
| Description: | Startup without video input end error (C) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 808 |
| Display: | SYSTEM HALT (*) 808 : FW/STP-MTR |
| Description: | Startup without video input end error (R) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 809 |
| Display: | SYSTEM HALT (*) 809 : FW/XY param |
| Description: | Startup without video input end error (G) Video transfer to the engine is started, but a video transmission end command is not issued by the engine within the specified time. |
| Causes: | • Defective controller board |
| Error code: | 80a |
| Display: | SYSTEM HALT (*) 80a : FW/Y RANGE |
| Description: | FW error (Y movable range error) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 80b |
| Display: | SYSTEM HALT (*) 80b : FW/ctrltsk |
| Description: | FW error (Motor control task error) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 80c |
| Display: | SYSTEM HALT (*) 80c : FW/PUMP W |
| Description: | FW error (Suction Pump stop waiting time over at capping) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 80d |
| Display: | SYSTEM HALT (*) 80d : FW/SERVO IT |
| Description: | FW error (Servo interruption error) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 80e |
| Display: | SYSTEM HALT (*) 80e : FW/FROM prm |
| Description: | FW error (FROM PARAM error (F/W BUG)) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 80f |
| Display: | SYSTEM HALT (*) 80f : FW/SIO vch FW error (Virtual serial CH setting error) |
| Description: | FW error (Virtual serial CH setting error) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 810 |
| Display: | SYSTEM HALT (*) 810 : FW/KEY RDI |
| Description: | Startup without video input end error (B) Video transfer to the engine is started, but a video transmission end command is not issued by the engine within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 811 |
| Display: | SYSTEM HALT (*) 811 : FW/SIO read |
| Description: | FW error (Serial control F/W error (RD BUSY)) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 812 |
| Display: | SYSTEM HALT (*) 812 : FW/CRTRG NO |
| Description: | FW error (Cartridge number error) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 813 |
| Display: | PRESS POWER SW FOR 5SEC Error : 813 |
| Description: | SU Communication Error |
| Causes: | Communication error between the Controller and the Scanner Unit is detected. |
| Remedy: | Turn off and on the MFP. |
| Error code: | 814 |
| Display: | PRESS POWER SW FOR 5SEC Error : 814 |
| Description: | SU FW Removed It is an error to notify that SU FW was erased by special key operation from a panel. |
| Remedy: | It is an error to notify that SU FW was erased by special key operation from a panel. |
| Error code: | 815 |
| Display: | Power OFF/ON 815:Error |
| Description: | Mailbox is full. |
| Remedy: | Cycle the power. |
| Error code: | 816 |
| Display: | SYSTEM HALT (*) 816 : FW/FROM WRC |
| Description: | Energy saving I/O sub-system error |
| Causes: | The energy saving I/O sub-system detects an error. • Defective energy saving I/O sub-system • The energy saving I/O sub-system detects a controller board error (No response) |
| Remedy: | • Turn the main power switch off and on. • Replace the controller board. |
| Error code: | 817 |
| Display: | SYSTEM HALT (*) 817 : FW/SaveArea |
| Description: | Monitor error This is a file detection and electronic file signature check error when the boot loader attempts to read the self-diagnostic module, system kernel, or root system files from the OS Flash ROM, or the items on the SD card in the controller slot are false or corrupted. |
| Causes: | OS Flash ROM data defective. SD card data defective. Change the controller firmware. Use another SD card. |
| Remedy: | • Change the controller firmware. • Use another SD card. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 81a |
| Display: | SYSTEM HALT (*) 81a : FW/FROM SIZ |
| Description: | FW error (FROM size over) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 81b |
| Display: | SYSTEM HALT (*) 81b : FW/STACK OV |
| Description: | FW error (STACK OVER) |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 902 |
| Display: | Power OFF/ON 902:Error |
| Description: | Engine software error |
| Causes: | These errors indicate an unrecoverable system software error. |
| Remedy: | Replace the system board. |
| Error code: | 90d |
| Display: | ERROR 90d NO HEAD SELECT |
| Description: | Loaded number of the head is assumed zero. |
| Remedy: | Check the setting of loading number of the head in the parameter. (System parameter No.41 HEAD NO=3) |
| Error code: | n01 |
| Display: | NO ATC UNIT |
| Description: | The [ATC] menu item was executed, but no ATC unit is installed. |
| Causes: | Instantaneous excessive load was given to the X-axis. |
| Remedy: | The [ATC] menu item can be executed, only when an ATC unit is installed. After a short interval, the machine automatically returns to the original screen. |
| Error code: | n02 |
| Display: | NOW CATCHING TOOL "ENTER" TO RELEASE |
| Description: | The power was switched on while a tool was in a gripped state. |
| Causes: | Big load has been given to the X-axis continuously. |
| Remedy: | When the power is switched on while a tool is gripped, the tool is released to ensure safety. Pressing the [ENTER] key immediately performs a forced release and clears the error. No operation to return the tool to the magazine is performed, so support the tool with your hand as you perform this operation to keep the tool from being dropped. (1)Press the [ENTER] key. A forced release is performed, and the message [IF TOOL IS RELEASED, THEN PUSH "ENTER"] appears. (2)If the tool was released, then press the [ENTER] key to clear the error. If the tool was not released, then switch off the power. Make sure the air pressure is within the specified range and that no air hoses of cables have come loose, then switch on the power. If the error message appears again, press the [ENTER] key. If this operation fails to release the tool, then contact your Roland DG Corp. service center. If this message does not appear even though a tool is grasped, then immediately switch off the power and contact your Roland DG Corp. service center. |
| Error code: | n03 |
| Display: | NO Z0 SENSOR SET SENSOR THEN ENTER |
| Description: | An attempt was made to carry out automatic measurement of tool length while the Z0 sensor was not connected. |
| Causes: | Big load has been given to the X-axis continuously for a long time. |
| Remedy: | The Z0 sensor is required in order to execute [LENGTH SCAN] (although this is not required when the rotary axis unit is installed). Connect the Z0 sensor, place it on the sensor base, then press the [ENTER] key. The machine clears the error, then restarts measurement. |
| Error code: | n04 |
| Display: | TOOL LENGTH TOO LONG SHORTEN IT AND ENTER |
| Description: | Automatic measurement cannot be performed because the tool is too long. |
| Causes: | Big load has been given to the X-axis continuously. Thermister of the X driver IC is defective. |
| Remedy: | On executing [LENGTH SCAN], if the tool is too long and measurement cannot be performed, this message appears and the tool is returned to the magazine. Replace the tool with one of the specified length, then press the [ENTER] key. The machine clears the error, then restarts measurement. |
| Error code: | n05 |
| Display: | AIR PRESSURE SHORT |
| Description: | Operation was interrupted because the pressure of the compressed air was lower than permitted. |
| Causes: | Instantaneous excessive load was given to the Y-axis. |
| Remedy: | This appears when the pressure of the compressed air is insufficient. First, readjust the air pressure to 0.5 to 0.65 MPa. When the display changes to ["ENTER" TO CONTINUE], press the [ENTER] key. The error is cleared and the operation resumes. |
| Error code: | n06 |
| Display: | AIR PRESSURE TOO HIGH |
| Description: | Operation was interrupted because the pressure of the compressed air was higher than permitted. |
| Causes: | Big load has been given to the Y-axis continuously. |
| Remedy: | This appears when the pressure of the compressed air is excessively high. First, readjust the air pressure to 0.5 to 0.65 MPa. When the display changes to ["ENTER" TO CONTINUE], press the [ENTER] key. The error is cleared and the operation resumes. |
| Error code: | n07 |
| Display: | OPERATING ERROR CAN`T RELEASE TOOL |
| Description: | The tool cannot be released. |
| Causes: | Big load has been given to the Y-axis continuously for a long time. |
| Remedy: | This appears when the grasped tool could not be released for some reason. Switch off the power and make sure the air pressure is within the permitted range. Also make sure that no air hoses or cables have come loose. Switch on the power again. When [NOW CATCHING TOOL "ENTER" TO RELEASE] appears, press the [ENTER] key to try performing a forced release. (Be careful not to let the tool fall at this time.) If this operation fails to release the tool, then contact your Roland DG Corp. service center. |
| Error code: | n08 |
| Display: | Y overheat |
| Description: | Y motor driver becomes too hot. |
| Causes: | Big load has been given to the Y-axis continuously. Thermister of the Y driver IC is defective. |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. Replace the Main board. |
| Error code: | n09 |
| Display: | Z overload [peak] |
| Description: | Instantaneous excessive load was given to the Z-axis. |
| Causes: | Instantaneous excessive load was given to the Z-axis. |
| Remedy: | Check if there was no collision. Perform Load check. Check the Ball Thread. |
| Error code: | n10 |
| Display: | Z overload [short] |
| Description: | Big load has been given to the Z-axis continuously. |
| Causes: | Big load has been given to the Z-axis continuously. |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. |
| Error code: | n11 |
| Display: | Z overload [long] |
| Description: | Big load has been given to the Z-axis continuously for a long time. |
| Causes: | Big load has been given to the Z-axis continuously for a long time. |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. |
| Error code: | n12 |
| Display: | Z overheat |
| Description: | Z motor driver becomes too hot. |
| Causes: | Big load has been given to the Z-axis continuously. Thermister of the Z driver IC is defective. |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. Replace the Main board. |
| Error code: | n13 |
| Display: | A overload [peak] |
| Description: | Instantaneous excessive load was given to the A-axis. |
| Causes: | Instantaneous excessive load was given to the A-axis. |
| Remedy: | Check if there was no collision. Perform Load check. Check the Ball Thread. |
| Error code: | n14 |
| Display: | A overload [short] |
| Description: | Big load has been given to the A-axis continuously. |
| Causes: | Big load has been given to the A-axis continuously. |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. |
| Error code: | n15 |
| Display: | A overload [long] |
| Description: | Big load has been given to the A-axis continuously for a long time. |
| Causes: | Big load has been given to the A-axis continuously for a long time. |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. |
| Error code: | n16 |
| Display: | A overheat |
| Description: | A motor driver becomes too hot. |
| Causes: | Big load has been given to the A-axis continuously. Thermister |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. Replace the Main board. |
| Error code: | n17 |
| Display: | S driver overload |
| Description: | Big load is given to the Spindle motor driver for a long time. |
| Causes: | Big load has given to the A-axis continuously. |
| Remedy: | Check the milling condition. |
| Error code: | n18 |
| Display: | S overheat |
| Description: | Spindle motor becomes too hot. |
| Causes: | Big load has given to the A-axis continuously. Thermister of the Spindle motor is not operating correctly. |
| Remedy: | Check the milling condition. Replace the thermister for the Spindle motor. |
| Error code: | n19 |
| Display: | S driver overheat |
| Description: | Spindle motor driver becomes too hot. |
| Causes: | Big load has given to the A-axis continuously. Thermister of the Spindle motor driver IC is not operating correctly. |
| Remedy: | Check the milling condition. Replace the Spindle board. |
| Error code: | n20 |
| Display: | S power overload |
| Description: | Current to the Spindle motor driver becomes abnormal condition. |
| Causes: | Big load has given to the A-axis continuously. |
| Remedy: | Check the milling condition. |
