Mimaki UJV110
Рейтинг
Модули
WARM WATER BASE-1/2
WASTE INK TANK ASSY.
ELECTRICAL BOX ASSY.
ELECTRICAL UNIT ASSY. -2/2
X DRIVE ASSY.
ROLL ASSY.
HEAD UNIT ASSY.-3/3
ELECTRICAL UNIT ASSY. -1/2
COVER ASSY.-3/3
HEAD UNIT ASSY.-2/3
Y BAR ASSY.
COVER ASSY.-1/3
CLAMP ASSY.-2/2
PUMP ASSY.
HEAD UNIT ASSY.-1/3
UV ASSY.
WARM WATER BASE-2/2
CARTRIDGE FRAME ASSY.
FRAME ASSY.-2/2
STATION ASSY.-2/2
SLIDER ASSY.
FRAME ASSY.-1/2
TAKE-UP DEVICE ASSY.
COVER ASSY.-2/3
Y DRIVE ASSY.
STATION ASSY.-1/2
CLAMP ASSY.-1/2
Детали HEAD UNIT ASSY.-2/3
| Деталь: | Heater guard F |
| Парткод: | M505119 |
| Деталь: | Warm water space door |
| Парткод: | M505121 |
| Деталь: | Latch BKT |
| Парткод: | M505062 |
| Деталь: | Waste ink cap hinge plate |
| Парткод: | M505070 |
| Деталь: | Pin spring |
| Парткод: | M800564 |
| Деталь: | Cap fulcrum shaft |
| Парткод: | M204193 |
| Деталь: | UJ water heater replace operation plate J |
| Парткод: | M904149 |
| Деталь: | UJ water heater replace operation plate E |
| Парткод: | M904150 |
| Деталь: | Tank base |
| Парткод: | M505061 |
| Деталь: | Waste Ink Tube Guide |
| Парткод: | M601392 |
| Деталь: | Waste ink tank 2L |
| Парткод: | M601163 |
| Деталь: | Latch BKT |
| Парткод: | M505062 |
| Деталь: | Waste ink cap hinge plate |
| Парткод: | M505070 |
| Деталь: | Pin spring |
| Парткод: | M800564 |
| Деталь: | Cap fulcrum shaft |
| Парткод: | M204193 |
| Деталь: | Waste ink cap |
| Парткод: | M505069 |
| Деталь: | Waste tank base |
| Парткод: | M505073 |
| Деталь: | Waste tank sensor dog SUS |
| Парткод: | M505072 |
| Деталь: | Waste tank spring SUS |
| Парткод: | M800701 |
| Деталь: | Waste tank slider |
| Парткод: | M505071 |
| Деталь: | Collar 3-5-2 |
| Парткод: | M204192 |
| Деталь: | Electrical box cover 5 |
| Парткод: | M505166 |
| Деталь: | Electrical box cover 4 |
| Парткод: | M505165 |
| Деталь: | Electrical box cover 3 |
| Парткод: | M505164 |
| Деталь: | Electrical box cover 1 |
| Парткод: | M505162 |
| Деталь: | Electrical box cover 2 |
| Парткод: | M505163 |
| Деталь: | Electrical window cover 1 |
| Парткод: | M505169 |
| Деталь: | Electrical box cover 6 |
| Парткод: | M505167 |
| Деталь: | Electrical box cover 7 |
| Парткод: | M505774 |
| Деталь: | Electrical case 110 |
| Парткод: | M505194 |
| Деталь: | Connector BKT |
| Парткод: | M505776 |
| Деталь: | Right cover under BKT |
| Парткод: | M505219 |
| Деталь: | Power supply SW guard cover |
| Парткод: | M505369 |
| Деталь: | Left and right cover BKT |
| Парткод: | M505215 |
| Деталь: | Leg 110 |
| Парткод: | M505230 |
| Деталь: | Electrical box window cover 2 |
| Парткод: | M505170 |
| Деталь: | Winding guide rail |
| Парткод: | M505198 |
| Деталь: | UV power supply BKT |
| Парткод: | M505154 |
| Деталь: | UV power supply spacer 1 |
| Парткод: | M700393 |
| Деталь: | UV power supply holder |
| Парткод: | M505155 |
| Деталь: | UV power supply spacer 2 |
| Парткод: | M700394 |
| Деталь: | Winding main shaft 110 |
| Парткод: | M204245 |
| Деталь: | Antireflection sponge |
| Парткод: | M700343 |
| Деталь: | Power supply BKT |
| Парткод: | M505157 |
| Деталь: | Cooling fan box |
| Парткод: | M505223 |
| Деталь: | Cooling fan (platen) assy |
| Парткод: | E102925 |
| Деталь: | POWER SUPPLY |
| Парткод: | E300273 |
| Деталь: | V IO PCB assy |
| Парткод: | E102695 |
| Деталь: | Connection cable assy |
| Парткод: | E102907 |
| Деталь: | Station IO PCB assy |
| Парткод: | E102694 |
| Деталь: | IO PCB BKT |
| Парткод: | M505156 |
| Деталь: | Warm water control PCB assy |
| Парткод: | E102698 |
| Деталь: | X pulley BKT |
| Парткод: | M503418 |
| Деталь: | Pulley stopper 1 |
| Парткод: | M203353 |
| Деталь: | TN15-160 pulley |
| Парткод: | M203155 |
| Деталь: | XM BKT |
| Парткод: | M503419 |
| Деталь: | Bearing holder 2 |
| Парткод: | M204231 |
| Деталь: | X shaft motor all assy |
| Парткод: | M004348 |
| Деталь: | X shaft motor assy |
| Парткод: | E300294 |
| Деталь: | TN15-20 pulley |
| Парткод: | M203154 |
| Деталь: | X motor relay cable assy |
| Парткод: | E102896 |
| Деталь: | Couple shaft |
| Парткод: | M204229 |
| Деталь: | Coupling L |
| Парткод: | M203310 |
| Деталь: | Driving roller 110 |
| Парткод: | M204233 |
| Деталь: | Bearing shaft |
| Парткод: | M203306 |
| Деталь: | Roll base plate |
| Парткод: | M600906 |
| Деталь: | KNOB |
| Парткод: | M600056 |
| Деталь: | Roll base L assy |
| Парткод: | M004727 |
| Деталь: | Roll base L |
| Парткод: | M505686 |
| Деталь: | Roll holder shaft L |
| Парткод: | M203754 |
| Деталь: | Roll holder G |
| Парткод: | M600686 |
| Деталь: | Roll sub shaft |
| Парткод: | M300874 |
| Деталь: | Roll base R assy |
| Парткод: | M004728 |
| Деталь: | Roll holder |
| Парткод: | M600500 |
| Деталь: | Roll holder gear |
| Парткод: | M601168 |
| Деталь: | Roll holder shaft R |
| Парткод: | M203753 |
| Деталь: | SCREW |
| Парткод: | M400140 |
| Деталь: | Roll stopper A |
| Парткод: | M601087 |
| Деталь: | Roll stopper B2 |
| Парткод: | M505746 |
| Деталь: | Roll stopper SP2 |
| Парткод: | M800604 |
| Деталь: | Roll base R2 |
| Парткод: | M503830 |
| Деталь: | Cutter shaft |
| Парткод: | M203322 |
| Деталь: | Cutter BKT |
| Парткод: | M505201 |
| Деталь: | CUTTER SPRING |
| Парткод: | M800598 |
| Деталь: | CUTTER HOLDER |
| Парткод: | M601053 |
| Деталь: | Cutter actuator assy |
| Парткод: | E102933 |
| Деталь: | CUTTER HOLDER |
| Парткод: | M601086 |
| Деталь: | Cutter L |
| Парткод: | M201535 |
| Деталь: | Cutter roller |
| Парткод: | M601085 |
| Деталь: | Cutter screw |
| Парткод: | M400219 |
| Деталь: | Head sensor BKT |
| Парткод: | M505080 |
| Деталь: | Head BKT |
| Парткод: | M204228 |
| Деталь: | Height adjusting pin |
| Парткод: | M203314 |
| Деталь: | Pin guide |
| Парткод: | M601050 |
| Деталь: | Pin spring |
| Парткод: | M800564 |
| Деталь: | Sheet sensor BKT |
| Парткод: | M505197 |
| Деталь: | DM 1/3 Main PCB assy |
| Парткод: | E102476 |
| Деталь: | JV4 1394 I/F PCB assy |
| Парткод: | E102161 |
| Деталь: | JV4 I/F connection PCB assy |
| Парткод: | E102154 |
| Деталь: | UHC for CA 2x2 PCB assy |
| Парткод: | E102750 |
| Деталь: | UHC holder fix angle |
| Парткод: | M505158 |
| Деталь: | UHC holder (B) |
| Парткод: | M505046 |
| Деталь: | UHC guide |
| Парткод: | M601387 |
| Деталь: | Connection cable assy |
| Парткод: | E102906 |
| Деталь: | Slider relay PCB assy |
| Парткод: | E102691 |
| Деталь: | Main PCB BKT |
| Парткод: | M505159 |
| Деталь: | 200V terminal assy |
| Парткод: | E102872 |
| Деталь: | Terminal BKT |
| Парткод: | M505161 |
| Деталь: | Distributer terminal assy |
| Парткод: | E102844 |
| Деталь: | Connection cable assy |
| Парткод: | E102911 |
| Деталь: | UV IO PCB assy |
| Парткод: | E102696 |
| Деталь: | UV PCB BKT |
| Парткод: | M505160 |
| Деталь: | Right front cover holder top FC |
| Парткод: | M505115 |
| Деталь: | Right front cover holder under |
| Парткод: | M505245 |
| Деталь: | RIGHT SIDE COVER |
| Парткод: | M505239 |
| Деталь: | KB sheet |
| Парткод: | M903651 |
| Деталь: | LCD window |
| Парткод: | M600520 |
| Деталь: | KB panel |
| Парткод: | M601023 |
| Деталь: | KEY TOP |
| Парткод: | M601024 |
| Деталь: | Keyboard PCB assy |
| Парткод: | E102058 |
| Деталь: | Keyboard BKT |
| Парткод: | M505091 |
| Деталь: | Right cover FC |
| Парткод: | M505105 |
| Деталь: | Antireflection sponge |
| Парткод: | M700343 |
| Деталь: | Cartridge hold plate |
| Парткод: | M505269 |
| Деталь: | Rear cover holder |
| Парткод: | M505264 |
| Деталь: | RIGHT REAR COVER |
| Парткод: | M505267 |
| Деталь: | Tray R |
| Парткод: | M505231 |
| Деталь: | Right front cover BKT |
| Парткод: | M505243 |
| Деталь: | Damper BKT |
| Парткод: | M505104 |
| Деталь: | Damper BKT |
| Парткод: | M204201 |
| Деталь: | UV Optical attention name plate large |
| Парткод: | M903946 |
| Деталь: | Damper holder C |
| Парткод: | M505326 |
| Деталь: | Right front cover |
| Парткод: | M505265 |
| Деталь: | Right front under cover |
| Парткод: | M505247 |
| Деталь: | Winding relay cable assy |
| Парткод: | E102815 |
| Деталь: | Head assy |
| Парткод: | M005803 |
| Деталь: | DAMPER ASSY |
| Парткод: | M005841 |
| Деталь: | Damper coupling |
| Парткод: | M204246 |
| Деталь: | Damper cap assy |
| Парткод: | M601780 |
| Деталь: | O ring S25EP |
| Парткод: | M700355 |
| Деталь: | DAMPER |
| Парткод: | M601375 |
| Деталь: | Damper connector assy |
| Парткод: | M005842 |
| Деталь: | Connector cap |
| Парткод: | M601784 |
| Деталь: | O ring S8 |
| Парткод: | M700370 |
| Деталь: | Damper connector |
| Парткод: | M601401 |
| Деталь: | Head holder |
| Парткод: | M505807 |
| Деталь: | First filter holder |
| Парткод: | M505283 |
| Деталь: | Head BKT B |
| Парткод: | M204149 |
| Деталь: | Filter BKT |
| Парткод: | M505176 |
| Деталь: | FPC holder T |
| Парткод: | M504981 |
| Деталь: | Cap nut 2.5 |
| Парткод: | M204217 |
| Деталь: | Cap nut UJ-S4 |
| Парткод: | M204927 |
| Деталь: | O ring S4 |
| Парткод: | M700408 |
| Деталь: | Filter assy 10 |
| Парткод: | M601405 |
| Деталь: | AD piece |
| Парткод: | M204141 |
| Деталь: | Angle SP |
| Парткод: | M800570 |
| Деталь: | AD piece base |
| Парткод: | M204142 |
| Деталь: | Head guard plate |
| Парткод: | M204191 |
| Деталь: | HEAD COVER |
| Парткод: | M506078 |
| Деталь: | Head cover 2 |
| Парткод: | M506079 |
| Деталь: | Cutter cover F |
| Парткод: | M506080 |
| Деталь: | Bear guide film |
| Парткод: | M601416 |
| Деталь: | Y FPC guide |
| Парткод: | M505193 |
| Деталь: | Y FPC holder |
| Парткод: | M505083 |
| Деталь: | Y cable guide |
| Парткод: | M505209 |
| Деталь: | K washer |
| Парткод: | M502932 |
| Деталь: | Slider stopper L |
| Парткод: | M505224 |
| Деталь: | FPC guide |
| Парткод: | M505173 |
| Деталь: | Y bar UJV-110 |
| Парткод: | M300873 |
| Деталь: | LM guide UJV110 top |
| Парткод: | M800772 |
| Деталь: | LM guide UJV110 |
| Парткод: | M800706 |
| Деталь: | Y bar BKT R |
| Парткод: | M204432 |
| Деталь: | Y bar BKT L |
| Парткод: | M204595 |
| Деталь: | Scale holder |
| Парткод: | M601077 |
| Деталь: | Frame UJV-110 |
| Парткод: | M300872 |
| Деталь: | Damper hinge C |
| Парткод: | M505328 |
| Деталь: | COVER SENSOR ASSY |
| Парткод: | E102930 |
| Деталь: | Front cover SW BKT |
| Парткод: | M505107 |
| Деталь: | Left cover FC |
| Парткод: | M505106 |
| Деталь: | Antireflection sponge |
| Парткод: | M700343 |
| Деталь: | LEFT SIDE PLATE |
| Парткод: | M505240 |
| Деталь: | Left front cover holder top FC |
| Парткод: | M505117 |
| Деталь: | Left front cover holder under FC |
| Парткод: | M505246 |
| Деталь: | Left rear cover |
| Парткод: | M505268 |
| Деталь: | Cartridge holder plate |
| Парткод: | M505269 |
| Деталь: | Rear cover holder |
| Парткод: | M505264 |
| Деталь: | Left front cover BKT |
| Парткод: | M505244 |
| Деталь: | Damper BKT |
| Парткод: | M204201 |
| Деталь: | Damper holder |
| Парткод: | M505104 |
| Деталь: | UV Optical attention name plate large |
| Парткод: | M903946 |
| Деталь: | Damper holder C |
| Парткод: | M505326 |
| Деталь: | Left front cover |
| Парткод: | M505266 |
| Деталь: | Left front under cover |
| Парткод: | M505248 |
| Деталь: | Right and left cover BKT |
| Парткод: | M505215 |
| Деталь: | Left cover under BKT |
| Парткод: | M505220 |
| Деталь: | Tray L |
| Парткод: | M505232 |
| Деталь: | Clamp shaft |
| Парткод: | M204234 |
| Деталь: | Adjustable plate |
| Парткод: | M204733 |
| Деталь: | SPRING HOOK UPPER |
| Парткод: | M505171 |
| Деталь: | Spring hook lower |
| Парткод: | M505172 |
| Деталь: | PR |
| Парткод: | YEG-025 |
| Деталь: | PR shaft |
| Парткод: | M202182 |
| Деталь: | PR base |
| Парткод: | M204227 |
| Деталь: | Main cam |
| Парткод: | M600663 |
| Деталь: | Cam lever processed |
| Парткод: | M601415 |
| Деталь: | LEAF SPRING |
| Парткод: | M600666 |
| Деталь: | Fulcrum shaft |
| Парткод: | M202183 |
| Деталь: | Front hook |
| Парткод: | M600665 |
| Деталь: | Hook BKT |
| Парткод: | M502158 |
| Деталь: | Upper hook |
| Парткод: | M600664 |
| Деталь: | Suck pump BKT |
| Парткод: | M505066 |
| Деталь: | PUMP GEAR |
| Парткод: | M400216 |
| Деталь: | Suck pump base |
| Парткод: | M505067 |
| Деталь: | GEAR 24 |
| Парткод: | M601073 |
| Деталь: | UJV pump motor connection cable assy |
| Парткод: | E103018 |
| Деталь: | Suck motor |
| Парткод: | E300354 |
| Деталь: | Head adjuster holder |
| Парткод: | M505832 |
| Деталь: | Head adjuster |
| Парткод: | M601439 |
| Деталь: | Head adjuster SP |
| Парткод: | M800567 |
| Деталь: | Head UD BKT |
| Парткод: | M505203 |
| Деталь: | Head H shaft |
| Парткод: | M203316 |
| Деталь: | H shaft stopper |
| Парткод: | M601051 |
| Деталь: | H shaft fix shaft |
| Парткод: | M203318 |
| Деталь: | Head base guide shaft |
| Парткод: | M204238 |
| Деталь: | Head slant adjuster |
| Парткод: | M204237 |
| Деталь: | Head up and down spring hook L |
| Парткод: | M505355 |
| Деталь: | Head base SP |
| Парткод: | M800568 |
| Деталь: | Y slide base |
| Парткод: | M204596 |
| Деталь: | Head up and down spring hook |
| Парткод: | M505139 |
| Деталь: | Head base 1 |
| Парткод: | M204239 |
| Деталь: | Head base 2 |
| Парткод: | M204240 |
| Деталь: | Fan BKT |
| Парткод: | M505098 |
| Деталь: | DC FAN ASSY |
| Парткод: | E102909 |
| Деталь: | Y FPC holder |
| Парткод: | M505083 |
| Деталь: | Height adjusting pin |
| Парткод: | M203314 |
| Деталь: | Pin guide |
| Парткод: | M601050 |
| Деталь: | Pin spring |
| Парткод: | M800564 |
| Деталь: | Lamp BKT |
| Парткод: | M505206 |
| Деталь: | UV lamp fix plate |
| Парткод: | M505780 |
| Деталь: | Lamp up and down screw holder |
| Парткод: | M505196 |
| Деталь: | Lamp up and down screw |
| Парткод: | M204243 |
| Деталь: | Lamp up and down nut |
| Парткод: | M204244 |
| Деталь: | Bush housing |
| Парткод: | M204242 |
| Деталь: | Lamp guide shaft |
| Парткод: | M204241 |
| Деталь: | Lamp slider |
| Парткод: | M505205 |
| Деталь: | Lamp fix angle |
| Парткод: | M505195 |
| Деталь: | Suck bottle pad 1 |
| Парткод: | M601419 |
| Деталь: | Bottle holder 1 |
| Парткод: | M504997 |
| Деталь: | Bottle holder 2 |
| Парткод: | M504998 |
| Деталь: | Suck bottle pad 3 |
| Парткод: | M601421 |
| Деталь: | Suck bottle holder BKT |
| Парткод: | M504989 |
| Деталь: | Suck bottle pad 2 |
| Парткод: | M601420 |
| Деталь: | Thermo couple assy |
| Парткод: | E102832 |
| Деталь: | Terminal cover |
| Парткод: | M505744 |
| Деталь: | Float sensor (V) assy |
| Парткод: | E102849 |
| Деталь: | Tank cap |
| Парткод: | M204148 |
| Деталь: | Rubber packing |
| Парткод: | M700354 |
| Деталь: | Float sensor (V) relay cable assy |
| Парткод: | E102931 |
| Деталь: | Warm water electrical equipment BKT |
| Парткод: | M505140 |
| Деталь: | Diaphragm pump assy |
| Парткод: | E102764 |
| Деталь: | Heater fuse assy |
| Парткод: | E102779 |
| Деталь: | Warm water pump cassette base |
| Парткод: | M505216 |
| Деталь: | PUMP GEAR |
| Парткод: | M400216 |
| Деталь: | Warm water circulation motor |
| Парткод: | E300354 |
| Деталь: | GEAR 24 |
| Парткод: | M601073 |
| Деталь: | Suck bottle joint |
| Парткод: | M204277 |
| Деталь: | Cap processed |
| Парткод: | M601374 |
| Деталь: | Cartridge guide 1 |
| Парткод: | M600592 |
| Деталь: | ID contact PCB assy |
| Парткод: | E101959 |
| Деталь: | ID PCB holder |
| Парткод: | M601054 |
| Деталь: | Cartridge guide 2 |
| Парткод: | M601486 |
| Деталь: | Cap nut UJ-S4 |
| Парткод: | M204927 |
| Деталь: | O ring S4 |
| Парткод: | M700408 |
| Деталь: | Cartridge assy |
| Парткод: | M601427 |
| Деталь: | Cartridge frame |
| Парткод: | M600887 |
| Деталь: | Plate spring (C) |
| Парткод: | M502166 |
| Деталь: | Cartridge base R process |
| Парткод: | M601701 |
| Деталь: | Cartridge PCB assy |
| Парткод: | E102697 |
| Деталь: | Cartridge case top cover |
| Парткод: | M505233 |
| Деталь: | Cartridge case |
| Парткод: | M505234 |
| Деталь: | Cartridge base |
| Парткод: | M505352 |
| Деталь: | Cutting platen 3 |
| Парткод: | M204225 |
| Деталь: | Adsorption partition 2 |
| Парткод: | M700366 |
| Деталь: | Adsorption partition 1 |
| Парткод: | M700365 |
| Деталь: | Media holder S |
| Парткод: | M505687 |
| Деталь: | Media holder S slider |
| Парткод: | M204433 |
| Деталь: | Air cooling duct R |
| Парткод: | M505211 |
| Деталь: | Intake |
| Парткод: | M505213 |
| Деталь: | Cutting platen 1 |
| Парткод: | M204223 |
| Деталь: | Air cooling duct L |
| Парткод: | M505212 |
| Деталь: | Cutting platen 2 |
| Парткод: | M204224 |
| Деталь: | P cover F rubber 110 |
| Парткод: | M700371 |
| Деталь: | Platen cover F |
| Парткод: | M505256 |
| Деталь: | Bearing holder 1 |
| Парткод: | M204230 |
| Деталь: | Left assistance side plate |
| Парткод: | M505242 |
| Деталь: | Platen FF |
| Парткод: | M505254 |
| Деталь: | Platen earth plate |
| Парткод: | M505255 |
| Деталь: | Right assistance side plate |
| Парткод: | M505241 |
| Деталь: | Suck slide shaft cover |
| Парткод: | M505225 |
| Деталь: | Suck nozzle cover |
| Парткод: | M505079 |
| Деталь: | Suck BKT |
| Парткод: | M601391 |
| Деталь: | Suck nozzle 2.5 |
| Парткод: | M601390 |
| Деталь: | Suck nozzle holder |
| Парткод: | M204196 |
| Деталь: | Wiper belt holder plate UJ |
| Парткод: | M505081 |
| Деталь: | Wiper gear flange |
| Парткод: | M503696 |
| Деталь: | Wiper gear S |
| Парткод: | M601055 |
| Деталь: | Nozzle F-R motor |
| Парткод: | E300354 |
| Деталь: | Station motor gear |
| Парткод: | M400211 |
| Деталь: | Wiper motor BKT S |
| Парткод: | M503455 |
| Деталь: | W-T BKT |
| Парткод: | M504293 |
| Деталь: | COLLAR |
| Парткод: | M204204 |
| Деталь: | Tension pulley ST |
| Парткод: | M601393 |
| Деталь: | Wiper sensor BKT UJ |
| Парткод: | M505082 |
| Деталь: | Maintenance BKT F |
| Парткод: | M505078 |
| Деталь: | Wiper shaft F |
| Парткод: | M204195 |
| Деталь: | Cap holder |
| Парткод: | M504985 |
| Деталь: | Cap rubber T30 |
| Парткод: | M700380 |
| Деталь: | Ink exhaust pipe |
| Парткод: | M204143 |
| Деталь: | Cap base |
| Парткод: | M204145 |
| Деталь: | Cap BKT P |
| Парткод: | M601369 |
| Деталь: | Ink guard plate |
| Парткод: | M505074 |
| Деталь: | Cap sensor dog |
| Парткод: | M505075 |
| Деталь: | Suck tube assy |
| Парткод: | M005843 |
| Деталь: | Slider PCB BKT |
| Парткод: | M506081 |
| Деталь: | SLIDER PCB assy |
| Парткод: | E102692 |
| Деталь: | Slider PCB BOX |
| Парткод: | M505086 |
| Деталь: | Slider PCB BKT |
| Парткод: | M505208 |
| Деталь: | Y FPC holder |
| Парткод: | M505083 |
| Деталь: | Slider stopper L |
| Парткод: | M505224 |
| Деталь: | Scale spring |
| Парткод: | M800565 |
| Деталь: | Scale hook |
| Парткод: | M503397 |
| Деталь: | Scale holder R |
| Парткод: | M503398 |
| Деталь: | L sensor BKT U |
| Парткод: | M505053 |
| Деталь: | UJ1 encoder PCB assy |
| Парткод: | E102653 |
| Деталь: | Linear encoder scale UJV-110 |
| Парткод: | E300386 |
| Деталь: | Slider stopper R |
| Парткод: | M503503 |
| Деталь: | Scale holder L |
| Парткод: | M503399 |
| Деталь: | Station rear cover |
| Парткод: | M505275 |
| Деталь: | Cap rear cover |
| Парткод: | M505274 |
| Деталь: | Platen cover R1200 |
| Парткод: | M505684 |
| Деталь: | Flushing tray |
| Парткод: | M505124 |
| Деталь: | Adsorption partition 3 |
| Парткод: | M700367 |
| Деталь: | Paper sensor R BKT |
| Парткод: | M503524 |
| Деталь: | Paper rear end sensor connection assy |
| Парткод: | E102817 |
| Деталь: | Frame UJV-110 |
| Парткод: | M300872 |
| Деталь: | Flushing tray holder |
| Парткод: | M505348 |
| Деталь: | Adsorption fan BKT |
| Парткод: | M505210 |
| Деталь: | DC FAN ASSY |
| Парткод: | E102909 |
| Деталь: | Winding side plate L |
| Парткод: | M505199 |
| Деталь: | Roll base M |
| Парткод: | M600509 |
| Деталь: | HOLDER SHAFT |
| Парткод: | M202118 |
| Деталь: | Roll holder |
| Парткод: | M600500 |
| Деталь: | Extension bushing |
| Парткод: | M600541 |
| Деталь: | Extension long bushing |
| Парткод: | M600540 |
| Деталь: | Winding main shaft |
| Парткод: | M204245 |
| Деталь: | Winding right assy |
| Парткод: | M004403 |
| Деталь: | TL shaft (180) |
| Парткод: | M202502 |
| Деталь: | Winding cover |
| Парткод: | M601026 |
| Деталь: | TL BKT |
| Парткод: | M503529 |
| Деталь: | TL gear (180) |
| Парткод: | M400202 |
| Деталь: | Winding motor cable assy |
| Парткод: | E102129 |
| Деталь: | Winding motor PCB assy |
| Парткод: | E101185 |
| Деталь: | M gear (A) (180) |
| Парткод: | M202782 |
| Деталь: | Winding motor BKT |
| Парткод: | M503530 |
| Деталь: | Winding motor switch assy |
| Парткод: | E101209 |
| Деталь: | Winding motor assy |
| Парткод: | E101604 |
| Деталь: | Winding side plate R |
| Парткод: | M505200 |
| Деталь: | Center rear cover |
| Парткод: | M505261 |
| Деталь: | COVER SENSOR ASSY |
| Парткод: | E102930 |
| Деталь: | Front cover SW BKT |
| Парткод: | M505107 |
| Деталь: | REAR COVER |
| Парткод: | M505262 |
| Деталь: | Damper holder |
| Парткод: | M505104 |
| Деталь: | Damper BKT |
| Парткод: | M204201 |
| Деталь: | UV shading curtain R110 |
| Парткод: | M601697 |
| Деталь: | Shading curtain holder rear |
| Парткод: | M505263 |
| Деталь: | TOP COVER |
| Парткод: | M505259 |
| Деталь: | Exhaust elbow |
| Парткод: | M505273 |
| Деталь: | Exhaust vent guard |
| Парткод: | M506119 |
| Деталь: | Damper hinge C |
| Парткод: | M505328 |
| Деталь: | Center cover BKT |
| Парткод: | M505260 |
| Деталь: | FRONT TOP COVER |
| Парткод: | M505258 |
| Деталь: | FRONT COVER HINGE |
| Парткод: | M505257 |
| Деталь: | Front cover window plate holder |
| Парткод: | M505252 |
| Деталь: | Front cover window plate |
| Парткод: | M601431 |
| Деталь: | UJV cover caution plate |
| Парткод: | M904152 |
| Деталь: | Front cover insulation |
| Парткод: | M601432 |
| Деталь: | UV Optical attention name plate large |
| Парткод: | M903946 |
| Деталь: | FRONT COVER |
| Парткод: | M505251 |
| Деталь: | UV Optical attention name plate |
| Парткод: | M903747 |
| Деталь: | Shading curtain holder front |
| Парткод: | M505347 |
| Деталь: | UV shading curtain F110 |
| Парткод: | M601696 |
| Деталь: | Y-SP plate 24N |
| Парткод: | M505621 |
| Деталь: | Y-SP |
| Парткод: | M800569 |
| Деталь: | Y-T fulcrum shaft 24 |
| Парткод: | M204198 |
| Деталь: | Y-T pulley BKT 24 |
| Парткод: | M504987 |
| Деталь: | Y-T BKT24 |
| Парткод: | M504986 |
| Деталь: | Y DRIVEN PULLEY ASSY |
| Парткод: | M006281 |
| Деталь: | Y-T pulley shaft 24 |
| Парткод: | M204197 |
| Деталь: | Y driven pulley 24N |
| Парткод: | M204270 |
| Деталь: | Belt holder S |
| Парткод: | M504982 |
| Деталь: | Belt holder |
| Парткод: | M400254 |
| Деталь: | D BKT U |
| Парткод: | M502708 |
| Деталь: | Y driven pulley washer |
| Парткод: | M505249 |
| Деталь: | Y DRIVE PULLEY ASSY |
| Парткод: | M006280 |
| Деталь: | Y driven pulley collar |
| Парткод: | M204271 |
| Деталь: | Y drive pulley 24N |
| Парткод: | M204268 |
| Деталь: | D pulley 24N |
| Парткод: | M204269 |
| Деталь: | D-BKT |
| Парткод: | M505222 |
| Деталь: | DM pulley |
| Парткод: | M202666 |
| Деталь: | UJ_Y motor assy |
| Парткод: | E102966 |
| Деталь: | YM spacer |
| Парткод: | M202665 |
| Деталь: | YM top plate |
| Парткод: | M502710 |
| Деталь: | Belt holder UV 1 |
| Парткод: | M505779 |
| Деталь: | Belt use screw |
| Парткод: | M400140 |
| Деталь: | Slider couple plate |
| Парткод: | M505204 |
| Деталь: | Belt holder HD |
| Парткод: | M505058 |
| Деталь: | Cap up and down guide 1 |
| Парткод: | M601388 |
| Деталь: | Cap up and down guide 2F |
| Парткод: | M601389 |
| Деталь: | Cap frame |
| Парткод: | M505076 |
| Деталь: | Cap frame guide |
| Парткод: | M504988 |
| Деталь: | Station shaft assy |
| Парткод: | M505077 |
| Деталь: | Station cam |
| Парткод: | M601047 |
| Деталь: | Station base UJ |
| Парткод: | M504991 |
| Деталь: | Station U-D motor |
| Парткод: | E300354 |
| Деталь: | Station motor gear |
| Парткод: | M400211 |
| Деталь: | Station gear 1 |
| Парткод: | M601045 |
| Деталь: | Station gear 2 |
| Парткод: | M601046 |
| Деталь: | Cam shaft UJ |
| Парткод: | M204194 |
| Деталь: | S-T BKT |
| Парткод: | M503800 |
| Деталь: | Tension pulley ST |
| Парткод: | M601393 |
| Деталь: | COLLAR |
| Парткод: | M204204 |
| Деталь: | D position sensor BKT |
| Парткод: | M503453 |
| Деталь: | Clamp damper holder |
| Парткод: | M505137 |
| Деталь: | Clamp damper BKT |
| Парткод: | M505138 |
| Деталь: | Clamp damper box |
| Парткод: | M204235 |
| Деталь: | Clamp bush |
| Парткод: | M600694 |
| Деталь: | LC end BK |
| Парткод: | M505202 |
| Деталь: | CL B assy |
| Парткод: | M503515 |
| Деталь: | Lever knob G |
| Парткод: | M601090 |
| Деталь: | Roll stopper B |
| Парткод: | M505683 |
| Деталь: | CL link |
| Парткод: | M505236 |
| Деталь: | CL sensor BKT |
| Парткод: | M503520 |
| Деталь: | Clamp lever |
| Парткод: | M601066 |
| Деталь: | LEVER ASSY |
| Парткод: | M505250 |
Коды ошибок
43
44
50
51
53
60
61
70
71
72
73
74
90
n01
n02
n03
n04
n05
n06
n07
n08
n09
n10
n11
n12
n13
n14
Описание
| Error code: | 43 |
| Display: | Send Error (AUTH) |
| Description: | 10-353 ERROR 43 FUSER SSR1 ON TIME FAILURE |
| Causes: | 1. The ‘Open Cover’ microswitch may be stuck or faulty 2. Check the connector and cables between Switch and main PBA. |
| Remedy: | Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board. |
| Error code: | 44 |
| Display: | Send Error (DNS) |
| Description: | Fuser Sub Lamp Overheat Failure, Code 44 The front thermistor has detected an overheat condition. Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault is performed. |
| Causes: | • Fuser • Engine Control Board |
| Remedy: | 1 1. Turn OFF power, remove the fuser assembly and allow it to cool down. 2. Measure the resistance between the Fuser connector P600-7 and P600-9. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 2. Replace the fuser assembly. 2 1. Reinstall the fuser assembly. 2. Enter service diagnostics. 3. From the Sensor Tests run the Fuser Temperature test. 4. Is the temperature indicated approximately 165o C? Go to step 4. Go to step 3. 3 1. Turn OFF printer power. 2. Measure the resistance between J641-4 and J641-5 on the engine control board. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 4. Repair or replace the wiring harness. 4 1. Turn printer power back ON. 2. Is there ~+3.4 VDC between J590-3 and ground? Check the AC wiring harness to the fuser. If the check is OK, replace the AC drive assembly. Replace the engine control board. |
| Error code: | 50 |
| Display: | Tray 2 Paper Empty |
| Description: | Fuser Fan Failure The Fuser Fan rotation signal indicates to the Engine Control Board that the fan is no longer operational. |
| Causes: | • Fuser Fan, PL5.3.31 • FAN/PHD/MOT Harness, PL10.1.9 • Engine Control Board, PL9.1.16 |
| Remedy: | 1 Check the Fuser Fan for damage. Remove the Front Cover. Is the fan damaged? Replace the Fuser Fan. Go to Step 2. 2 Check the Fuser Fan connection. Is P/J482 connected to the harness? Go to Step 2. Reconnect the Fan. 3 Check orientation of the Fuser Fan. Does the Fan’s label face into the chute? Go to Step 3. Correct the installation. 4 Test the Fuser Fan. Run the Service Diagnostics Fuser Fan test. Does the Fan operate. Go to Step 6. Go to Step 5. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J482. 2. Check continuity between J48 <=> P483. Go to Step 5. Replace the FAN/PHD/MOT Harness. 6 Check the fan rotation signal. Print one sheet. Is there +3.3 V across P/J48-A12 <=> P/J48-A13? Replace the Engine Control Board. Replace the Fuser Fan. |
| Error code: | 51 |
| Display: | Send Error (DNS) |
| Description: | Rear Fan Failure The Rear Fan rotation signal indicates the fan is no longer operational. |
| Causes: | • Rear Fan, PL1.1.19 • LVPS, PL9.1.6 • Engine Control Board, PL9.1.16 • LV Harness, PL10.1.2 |
| Remedy: | 1 Check the Rear Fan for damage. Remove the Rear Cover. Is the fan damaged? Replace the Rear Fan. Go to Step 2. 2 Check the Rear Fan connection. Is P/J166 connected to the harness? Go to Step 3. Connect the Fan. 3 Check orientation of the Rear Fan. Does the Fan’s label face inwards? Go to Step 4. Correct the installation. 4 Test the Rear Fan. Run the Service Diagnostics Rear Fan test. Does the fan operate? Go to Step 6. Go to Step 5. 5 Check for +24 V to the fan. Disconnect P/J166. Is there +24 V across P166-1 <=> P166-3? Replace the Rear Fan. Replace the LVPS. 6 Check the fan rotation signal to the LVPS. Print one sheet. Is there +3.3 V between P/J166-1 <=> P/J166-3? Replace the Fuser Fan. Go to Step 7. 7 Check the rotation signal from the LVPS. Print one sheet. Is there +3.3 V between P/J165-15 <=> P/J165-3? Replace the LVPS. Go to Step 8. 8 Check the fan rotation signal at the Engine Control Board. Print one sheet. Is there +3.3 V between P/J61-4 <=> P/J61-16? Replace the LV Harness Replace the Engine Control Board. |
| Error code: | 53 |
| Display: | Send Error (SMTP) |
| Description: | The password did not match in a relay or mailbox transmission, and the transmission ended in failure. |
| Causes: | · Loose cable connection · Defective controller fan · Defective IOD1 board · Defective MCTL board |
| Remedy: | Confirm that both parties are using the same system password and the both units are compatible. Then, ask the remote party to transmit again. |
| Error code: | 60 |
| Display: | Nongenuine Toner |
| Description: | Imaging Unit Motor Failure, Code 60 |
| Causes: | • Imaging Unit Drive Motor • Engine Control Board |
| Remedy: | 1 1. Enter service diagnostics and run the Imaging Unit Motor test. 2. Does the motor operate correctly? Go to step 7. Go to step 2. 2 1. Is the voltage at J210-5 +5 VDC? Go to step 3. Replace the engine control board. 3 1. Is the voltage at J210-7 +24 VDC? Go to step 4. Use the +24 VDC wirenets to troubleshoot and resolve the missing voltage. 4 1. Enter service diagnostics. 2. While running the Imaging Unit Motor test, check the voltage at J210-1 and J210-2. 3. Is the voltage 0 VDC while the test is running? Go to step 5. Replace the engine control board. 5 Is the frequency between J210-4 and ground between 1 KHz and 1.3 KHz? Replace the imaging unit drive motor. Go to step 6. 6 1. Check for a short to ground at J210-4. 2. Is the wire grounded? Repair or replace the wiring harness. Replace the engine control board. 7 1. Enter service diagnostics. 2. While running the Imaging Unit Motor test, check the voltage at J210-9. 3. Is the voltage +5 VDC while the test is running? Replace the imaging unit drive motor. Replace the engine control board. |
| Error code: | 61 |
| Display: | Nongenuine Toner Replace Toner 1 |
| Description: | The toner cartridge installed is not a genuine cartridge. |
| Causes: | The printer warms up when the printer is turned on or the cover is closed, or wake from sleep mode. |
| Remedy: | This message appears when you selected stop at the Non Genuine Toner prompt. Install the genuine toner cartridge. |
| Error code: | 70 |
| Display: | No Paper |
| Description: | No Paper |
| Causes: | No paper in the paper cassette. |
| Error code: | 71 |
| Display: | Paper Jam 0 |
| Description: | Paper Jam 0 |
| Causes: | The front part of paper is jammed between pickup unit and Feed sensor. |
| Error code: | 72 |
| Display: | Paper Jam 1 |
| Description: | Engine Firmware Failure The Engine Control Board detected a firmware error. |
| Causes: | • Engine Control Board, Pl9.1.16 • EEPROM Board, PL9.1.12 |
| Remedy: | 1 Cycle printer power. Does the error persist? Go to Step 2. Complete 2 Is P/J144 on the EEPROM Board properly seated and defect free? Go to Step 3. Reseat P/J144 or replace the EEPROM Board. 3 Turn printer power off and then back on. Does the error persist? Replace the Engine Control Board. Complete |
| Error code: | 73 |
| Display: | Paper Jam 2 |
| Description: | Paper Jam 2 |
| Causes: | The front part of paper is jammed just after passing through the discharge sensor. |
| Error code: | 74 |
| Display: | [TRAY x] [PAPER SIZE] EMPTY |
| Description: | F/W Overrun detect |
| Causes: | · Loose cable connection · Defective cleaner clutch · Defective IOD2 board · Defective IOD1 board · Defective MCTL board |
| Remedy: | 1) Check the harness connected between the Engine controller and the TA board. (If the harness is out, insert it to the connector.) 2) Check the harness connected between the TA board and the Pickup unit. (If the harness is out, insert it to the connector.) 3) Check the harness connected between the Pickup unit and the cassette sensing board. (If the harness is out, insert it to the connector.) 4) Check the pickup unit. (If it is inferior part or warped part, replace it.) 5) Check the damage of the cassette sensing B . (If it is damaged, replace the cassette sensing board.) 6) In the Engine diagnostic mode, operate the running count of the paper if it is under 39. (If it is over 39, replace the Pickup unit.) 7) Replace the TA board. |
| Error code: | 90 |
| Display: | ERROR 90 F / W |
| Description: | Sub CPU fault. |
| Remedy: | Replace the CPU circuit board with a new one. |
| Error code: | n01 |
| Display: | NO ATC UNIT |
| Description: | The [ATC] menu item was executed, but no ATC unit is installed. |
| Causes: | Instantaneous excessive load was given to the X-axis. |
| Remedy: | The [ATC] menu item can be executed, only when an ATC unit is installed. After a short interval, the machine automatically returns to the original screen. |
| Error code: | n02 |
| Display: | NOW CATCHING TOOL "ENTER" TO RELEASE |
| Description: | The power was switched on while a tool was in a gripped state. |
| Causes: | Big load has been given to the X-axis continuously. |
| Remedy: | When the power is switched on while a tool is gripped, the tool is released to ensure safety. Pressing the [ENTER] key immediately performs a forced release and clears the error. No operation to return the tool to the magazine is performed, so support the tool with your hand as you perform this operation to keep the tool from being dropped. (1)Press the [ENTER] key. A forced release is performed, and the message [IF TOOL IS RELEASED, THEN PUSH "ENTER"] appears. (2)If the tool was released, then press the [ENTER] key to clear the error. If the tool was not released, then switch off the power. Make sure the air pressure is within the specified range and that no air hoses of cables have come loose, then switch on the power. If the error message appears again, press the [ENTER] key. If this operation fails to release the tool, then contact your Roland DG Corp. service center. If this message does not appear even though a tool is grasped, then immediately switch off the power and contact your Roland DG Corp. service center. |
| Error code: | n03 |
| Display: | NO Z0 SENSOR SET SENSOR THEN ENTER |
| Description: | An attempt was made to carry out automatic measurement of tool length while the Z0 sensor was not connected. |
| Causes: | Big load has been given to the X-axis continuously for a long time. |
| Remedy: | The Z0 sensor is required in order to execute [LENGTH SCAN] (although this is not required when the rotary axis unit is installed). Connect the Z0 sensor, place it on the sensor base, then press the [ENTER] key. The machine clears the error, then restarts measurement. |
| Error code: | n04 |
| Display: | TOOL LENGTH TOO LONG SHORTEN IT AND ENTER |
| Description: | Automatic measurement cannot be performed because the tool is too long. |
| Causes: | Big load has been given to the X-axis continuously. Thermister of the X driver IC is defective. |
| Remedy: | On executing [LENGTH SCAN], if the tool is too long and measurement cannot be performed, this message appears and the tool is returned to the magazine. Replace the tool with one of the specified length, then press the [ENTER] key. The machine clears the error, then restarts measurement. |
| Error code: | n05 |
| Display: | AIR PRESSURE SHORT |
| Description: | Operation was interrupted because the pressure of the compressed air was lower than permitted. |
| Causes: | Instantaneous excessive load was given to the Y-axis. |
| Remedy: | This appears when the pressure of the compressed air is insufficient. First, readjust the air pressure to 0.5 to 0.65 MPa. When the display changes to ["ENTER" TO CONTINUE], press the [ENTER] key. The error is cleared and the operation resumes. |
| Error code: | n06 |
| Display: | AIR PRESSURE TOO HIGH |
| Description: | Operation was interrupted because the pressure of the compressed air was higher than permitted. |
| Causes: | Big load has been given to the Y-axis continuously. |
| Remedy: | This appears when the pressure of the compressed air is excessively high. First, readjust the air pressure to 0.5 to 0.65 MPa. When the display changes to ["ENTER" TO CONTINUE], press the [ENTER] key. The error is cleared and the operation resumes. |
| Error code: | n07 |
| Display: | OPERATING ERROR CAN`T RELEASE TOOL |
| Description: | The tool cannot be released. |
| Causes: | Big load has been given to the Y-axis continuously for a long time. |
| Remedy: | This appears when the grasped tool could not be released for some reason. Switch off the power and make sure the air pressure is within the permitted range. Also make sure that no air hoses or cables have come loose. Switch on the power again. When [NOW CATCHING TOOL "ENTER" TO RELEASE] appears, press the [ENTER] key to try performing a forced release. (Be careful not to let the tool fall at this time.) If this operation fails to release the tool, then contact your Roland DG Corp. service center. |
| Error code: | n08 |
| Display: | Y overheat |
| Description: | Y motor driver becomes too hot. |
| Causes: | Big load has been given to the Y-axis continuously. Thermister of the Y driver IC is defective. |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. Replace the Main board. |
| Error code: | n09 |
| Display: | Z overload [peak] |
| Description: | Instantaneous excessive load was given to the Z-axis. |
| Causes: | Instantaneous excessive load was given to the Z-axis. |
| Remedy: | Check if there was no collision. Perform Load check. Check the Ball Thread. |
| Error code: | n10 |
| Display: | Z overload [short] |
| Description: | Big load has been given to the Z-axis continuously. |
| Causes: | Big load has been given to the Z-axis continuously. |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. |
| Error code: | n11 |
| Display: | Z overload [long] |
| Description: | Big load has been given to the Z-axis continuously for a long time. |
| Causes: | Big load has been given to the Z-axis continuously for a long time. |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. |
| Error code: | n12 |
| Display: | Z overheat |
| Description: | Z motor driver becomes too hot. |
| Causes: | Big load has been given to the Z-axis continuously. Thermister of the Z driver IC is defective. |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. Replace the Main board. |
| Error code: | n13 |
| Display: | A overload [peak] |
| Description: | Instantaneous excessive load was given to the A-axis. |
| Causes: | Instantaneous excessive load was given to the A-axis. |
| Remedy: | Check if there was no collision. Perform Load check. Check the Ball Thread. |
| Error code: | n14 |
| Display: | A overload [short] |
| Description: | Big load has been given to the A-axis continuously. |
| Causes: | Big load has been given to the A-axis continuously. |
| Remedy: | Check the milling condition. Perform Load check. Check the Ball Thread. |
