OKI C710dn

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

лазерная

Макс. формат

Число страниц в месяц

100000

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Технология печати	лазерная
Тип	лазерный/светодиодный
Число страниц в месяц	100 000
Область применения	большой офис
Размещение	настольный
Телефон
Печать фотографий
Копир
Сканер
Факс
Тип устройства	Принтер
Макс. формат	A4
Цветность печати	цветная
Принтер
Количество цветов	4
Прямая печать
Печать без полей
Пигментные чернила
Двусторонняя печать
Макс, разрешение для ч/б печати
По Y	600
По X	1 200
Скорость ч/б печати
A4	32
A4	30
Время выхода первого отпечатка
Ч/б	8
Цветн,	9
Сканер
Стандарт WIA
Отправка изображения по e-mail
Стандарт TWAIN
Расходные материалы
Ресурс ч/б картриджа/тонера	11 000
Ресурс цветного картриджа/тонера	11 500
Ресурс фотобарабана	30 000
Количество картриджей	4
Печать на:
Рулоне
Фотобумаге
CD/DVD
Пленках
Этикетках
Глянцевой бумаге
Конвертах
Матовой бумаге
Карточках
Плотность бумаги
Максимальная	220
Минимальная	64
Факс
Цветной
Телефон
Автоответчик
Стандарт DECT
Проводная трубка
Беспроводная трубка
АОН
Спикерфон
Caller ID
Шрифты и языки управления
Языки управления
PDF
PostScript 2
PCL 5e
PCL 6
PPDS
PostScript 3
PostScript
PCL 5c
Количество установленных шрифтов
PostScript	136
PCL	80
Лотки
Подача бумаги
Стандартная	630
Максимальная	1 690
Вывод бумаги
Стандартный	350
Финишер
Сортер
Степлер
Брошюровщик
Сортировка со сдвигом
Электронная сортировка
Интерфейсы
RS-232
Устройство для чтения карт памяти
Инфракрасный порт
Bluetooth
Wi-Fi
FireWire (IEEE 1394)
LPT
Веб-интерфейс
USB
Ethernet (RJ-45)
Версия USB	2,0
Память/Процессор
Частота процессора	700
Процессор	PowerPC
Макс, объем памяти	768
Объем памяти	256
Дополнительная информация
Мин. системные требования	Intel Pentium II
Экран
Поддержка ОС
DOS
Windows
Linux
Mac OS
Потребляемая мощность
В режиме ожидания	100
При работе	1 200
Уровень шума
При работе	55,6
Габариты
Ширина	435
Вес	27,5
Глубина	607
Высота	389

Модули

Frame Assy-OP

Cover-Assy-Top

Feeder-Unit

Eject-Assy

Plate-Assy-Side L

Plate-Assy-Side R

Cover Assy-OP

Printer NIP

Plate-Assy-Base

Детали

Деталь:	Core Assy.-FFC
Парткод:	43987901

Деталь:	CONN Cord-JST3P-AMP3P
Парткод:	43810401

Деталь:	Cable-RFID(Bend)
Парткод:	43297002

Деталь:	CONN Cord-AMP5P-AMP5P
Парткод:	43809401

Деталь:	Board-RSF
Парткод:	42135802

Деталь:	Guide Assy.-Eject-L
Парткод:	43076303

Деталь:	CONN Cord-AMP2PAMP2P-JST4P
Парткод:	43155001

Деталь:	OR-Motor_Pulse_Belt
Парткод:	43276401

Деталь:	CONN Cord-AMP4P-SW
Парткод:	43945401

Деталь:	OR-Motor_Pulse_Liftup
Парткод:	43276201

Деталь:	Gear-Idle-Exit-Z32
Парткод:	43085301

Деталь:	CONN Cord-AMP8P-AMP4PAMP4P
Парткод:	43138001

Деталь:	SOLENOID
Парткод:	42058303

Деталь:	Motor-Pulse-Hop
Парткод:	43925301

Деталь:	OR-PRZ
Парткод:	43131601

Деталь:	Motor-DC-ID-65M
Парткод:	43923501

Деталь:	CONN Cord-AMP11P-AMP11P
Парткод:	43810301

Деталь:	CONN Cord-AMP9P-AMP9P
Парткод:	43138301

Деталь:	OR-PRG
Парткод:	43925101

Деталь:	Cover-Assy.-Top
Парткод:	43896201

Деталь:	Frame Assy.-OP
Парткод:	43895201

Деталь:	Cover Assy.-OP
Парткод:	43895301

Деталь:	OR-PRY
Парткод:	43131301

Деталь:	Sensor Assy.-Color-Regist
Парткод:	43917501

Деталь:	Cover-Driver
Парткод:	42066901

Деталь:	Cover-Assy.-SideR-741
Парткод:	43917801

Деталь:	Plate-Shield-A
Парткод:	43738101

Деталь:	OR-Board PRH
Парткод:	43921701

Деталь:	Board]TB2
Парткод:	43793721

Деталь:	Board -TB2
Парткод:	55114701

Деталь:	Plate Assy.-Side R(PX741)
Парткод:	43921901

Деталь:	Eject Assy.-PX741
Парткод:	43924301

Деталь:	Plate Assy.-Base
Парткод:	43894301

Деталь:	Plate Assy.-Side L(PX-741)
Парткод:	43074903

Деталь:	PWR unit-DCDC
Парткод:	43770701

Деталь:	CONN-High Voltage(Bend)
Парткод:	43393801

Деталь:	Cover-Side(L)
Парткод:	43738301

Деталь:	Cassette-Assy]PX741
Парткод:	43894901

Деталь:	Frame-Assy-Retard
Парткод:	43895001

$oki\43963101.jpg$

Деталь:	Spring-Retard
Парткод:	43963101

Деталь:	Cover Assy.-Hopping
Парткод:	43894801

Деталь:	Plate-Front
Парткод:	42067602

Деталь:	Feeder-Unit-PX741
Парткод:	43895401

Деталь:	Plate-Driver(PU)(Caulking)
Парткод:	42062102

Деталь:	Gear-Idle-Belt-Z20Z93
Парткод:	43076101

Деталь:	Plate-Lockout-ID
Парткод:	43073510

Деталь:	Cover Assy.-FaceUP
Парткод:	43078702

Деталь:	Cover-Sub Assy.-Rear
Парткод:	43917701

Деталь:	LED Head Unit-51STA
Парткод:	43295201
Цена:	16 800 ₽

Деталь:	OR-Motor-FAN(80)
Парткод:	43289101

Деталь:	Guide-Cable-(Pow]low)
Парткод:	43746401

Деталь:	PWR unit-ACDC Switch
Парткод:	43704101

Деталь:	PWR unit-ACDC Switch
Парткод:	43987801

Деталь:	Spring-BeltFuse
Парткод:	42067001

Деталь:	Thermistor-Belt
Парткод:	42605201

Деталь:	Shaft-Liftup-PX734
Парткод:	43076501

Деталь:	Bush
Парткод:	42060701
Цена:	750 ₽

Деталь:	Gear-LiftupL-Z32
Парткод:	43075201

Деталь:	Gear-LiftUpLinkL-Z56
Парткод:	43075501

Деталь:	Plate-Heat
Парткод:	43110801

Деталь:	Spring-Torsion(L)
Парткод:	43921201

Деталь:	Spring-Torsion(R)
Парткод:	43921301

Деталь:	Plate-Logo
Парткод:	43912901

Деталь:	CONN-Cord-FlexyDP(Bend)
Парткод:	43348901

Деталь:	Label-Color K
Парткод:	43281101

Деталь:	Label-Color Y
Парткод:	43281102

Деталь:	Label-Color M
Парткод:	43281103

Деталь:	Label-Color C
Парткод:	43281104

Деталь:	CONN Cord-AMP9P-AMP4PAMP5P
Парткод:	43810201

Деталь:	Roller-Pick-Up
Парткод:	42699401

Деталь:	Roller-Feed-NOW
Парткод:	43000601

Деталь:	Rubber-Foot
Парткод:	42049901

Коды ошибок

002 ... 005

020

030

031

040

041

042 ... 045

072

073

074, 075

081

104

106

111

112

121

122

123

124

126

127

128

131 ... 134

142

150 ... 153

154

155

160 ... 163

167

168

170, 171

172, 173

174

175

176, 177

181, 182

190

200, 201, 202

203, 204, 207, 208

209

214, F0C, FFF

230

231

901 ... 904

918

923

928

980

982

983

Описание

Парткод

Название

OKI (43363402) Ремень переноса

OKI Термоблок (печка)

OKI Блок фотобарабана желтый

OKI Блок фотобарабана пурпурный

OKI Блок фотобарабана голубой

OKI Блок фотобарабана черный

OKI (44318605) Тонер-картридж желтый

OKI (44318606) Тонер-картридж пурпурный

OKI (44318607) Тонер-картридж голубой

OKI (44318608) Тонер-картридж черный

Error code:	002 ... 005
Display:	Restart the printer. 002: Error~ 005: Error
Description:	CPU Exception
Remedy:	Does the error display recur? If the RAM DIMM is installed, remove it and turn off the power of the printer and back on. Replace the CU board. Re-install the RAM DIMM. Replace the RAM DIMM.

Error code:	020
Display:	Service Call 020: Error
Description:	CU ROM Hash Check Error 1
Causes:	Is program ROM DIMM set properly? Is error recovered by replacing program ROM DIMM?
Remedy:	Reset program ROM DIMM. Replace program ROM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	030
Display:	Service Call 030: Error
Description:	CU Slot1 DIMM RAM Check Error
Causes:	Is subject RAM DIMM set properly? Is error recovered by replacing subject ROM DIMM?
Remedy:	Reset subject RAM DIMM. Replace RAM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	031
Display:	Service Call 031: Error
Description:	CU Slot2 DIMM RAM Check Error
Causes:	Is subject RAM DIMM set properly? Is error recovered by replacing subject ROM DIMM?
Remedy:	Reset subject RAM DIMM. Replace RAM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	040
Display:	Service Call 040: Error
Description:	CU EEPROM Error
Causes:	Is error recovered by replacing EEPROM on CU board?
Remedy:	Replace EEPROM. (Recover user environment.) Replace TIG board. (Replace EEPROM)

Error code:	041
Display:	Service Call 041: Error
Description:	CU Flash Error Flash ROM error on CU board.
Causes:	Does error display reappear?
Remedy:	Replace TIG board. (Replace EEPROM.)

Error code:	072
Display:	Service Call 072: Error
Description:	Engine communication error I/F error between PU-CU.
Causes:	Is CU assembly set properly? Is error recovered by replacing TIG board?
Remedy:	Set properly. Replace TIG board. (Replace EEPROM.) Replace PU board.

Error code:	073
Display:	Reboot the printer. 073: Error xxxxxxxx
Description:	Video Error Error is detected when expanding the video data. (Illegal data is received.)
Remedy:	Is the CU assembly installed normally? Does this error recur? Re-install the CU assembly normally. Change the PC with another PC having high specifications, or alternately reduce resolution power and execute the print again. Replace the CU board. Replace the interface cable. Re-install the PC Printer driver. Is the CU assembly installed normally? Does this error recur? Does the error depend on print Data? Re-install the CU assembly normally. Execute the print again. Print any other data. Replace the CU board. Send the data to design division and request analysis of the data.

Error code:	081
Display:	Service Call 081: Error
Description:	Parameter Match Check Error
Remedy:	Normal Read/Write not possible with EEPROM or Flash. If the condition does not change replace CU PCB.

Error code:	104
Display:	Service Call 104: Error
Description:	Developer Motor Failure The Developer Motor rotation signal indicates that the motor is no longer operational.
Causes:	• Developer Drive Assembly, PL8.1.1 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Check the Developer Drive Assembly for damage. Are any parts of the Developer Drive Assembly damaged or excessively worn? Replace the Developer Drive Assy. Go to Step 2. 2 Check the Developer Motor connection. Is P/J491 connected to the harness? Go to Step 3. Reconnect the Developer Motor. 3 Test the Developer Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Developer Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Developer Motor. Is the +24 V across P/J491-1 <=> P/J 481-5? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J491. 2. Check continuity between J48 <=> J491. Replace the Engine Control Board. Replace the FAN/PHD/MOT Harness.

Error code:	106
Display:	Service Call 106: Error
Description:	Motor Failure One of the primary drive motors has failed.
Causes:	• Main Drive Assembly, PL8.1.2 • Developer Drive Assembly, PL8.1.1 • Fuser Drive Assembly, PL5.2.25 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11
Remedy:	1 Check the motors. Run the Service Diagnostics motor tests to determine the failed part. Is the failed part the Main Drive Motor? Go to. Test the Fuser Motor. 2 Is the failed part the Fuser Drive Motor? Go to. Test the Developer Motor. 3 Is the failed part the Developer Drive Motor? Go to. Replace the Engine Control Board.

Error code:	111
Display:	SVC 111 ERROR
Description:	Printhead Error
Causes:	Incorrect color DTM installation, incorrect PCU installation, development bias error, MCU, LD control malfunction, loss of synchronization
Remedy:	No first Hysnc - magenta Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J11 and J12 on the system board. Go to “System board”. If the cables are connected correctly to the system board and to the printhead assembly, go to “Printhead diagnostics”

Error code:	112
Display:	SVC 112 ERROR
Description:	Printhead Error
Causes:	Incorrect color DTM installation, incorrect PCU installation, development bias error, MCU, LD control malfunction, loss of synchronization
Remedy:	No first Hysnc - yellow Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J7 and J8 on the system board. Go to “System board”. If the cables are connected correctly to the system board and to the printhead assembly, go to “Printhead diagnostics”. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics”

Error code:	121
Display:	Service Call 121: Error
Description:	Fuser Error
Causes:	Is cable between PU board andhighvoltage power LSI connected properly?
Remedy:	Wrong fuser lamp - BUR - replace the fuser assembly

Error code:	122
Display:	Service Call 122: Error
Description:	Finisher Decurler Failure, Code 122 The level of the Decurler Cam Home Sensor did not change 4 seconds after the Decurler Cam Clutch has turned on.
Causes:	• Decurler Cam Clutch • Stacker Motor • Finisher Control Board
Remedy:	1 1. Rotate the actuator while running the Decurler Cam Position test in diagnostics. 2. Does the value change between H and L? Go to step 2. Troubleshoot using the transmissive sensor procedure. 2 Does the decurler cam clutch operate in diagnostics? Check for a mechanical problem with the decurler cam clutch drive. If no problem is found replace the clutch. Go to step 3. 3 Is +24 VDC present at P/J 849-1? Replace the decurler cam clutch. Go to step 4. 4 Is +24 VDC present at test point 5 on the finisher control board? Replace the finisher control board. Troubleshoot the +24 VDC interlock circuit. 5 Is +24 VDC present at P/J 847-11 with the Finisher Stacker Motor Down test running in diagnostics? Replace the stacker motor. Replace the finisher control board

Error code:	123
Display:	Service Call 123: Error
Description:	Finisher Set Clamp Failure, Code 123 The set clamp home sensor did not turn on within 2 seconds after the set clamp started operation.
Causes:	• Set Clamp Solenoid • Finisher Control Board
Remedy:	1 1. Check the Set Clamp home sensor in diagnostics. 2. Does the value change from H to L while rotating the actuator? Go to step 2. Use the transmissive Sensor procedure to diagnose and repair the sensor. 2 Does the solenoid energize when running the Set Clamp Paddle test in diagnostics? Go to step 3. Go to step 4. 3 1. Run the Eject Forward Test and then the Eject Release Test in diagnostics. 2. Does the set clamp paddle turn once? Replace the finisher control board. Go to step 4. 4 Is +24 VDC present at P848A-10? Go to step 5. Go to step 6. 5 Is +24 VDC present at P848A-11? Replace the finisher control board. Replace the set clamp solenoid. 6 Is +24 VDC present at test point 9 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit.

Error code:	124
Display:	Service Call 124: Error
Description:	Finisher Communication Failure, Code 124
Remedy:	There are no diagnostic routines for problems involving serial communications. It is recommended that you address the following assemblies in this order: • Finisher Control Board • Engine Control Board • Perform continuity checks on any wiring harnesses involved.

Error code:	126
Display:	Turn power OFF and wait 126: Dew error
Description:	Fuser Error
Causes:	Sensor dew error detected.
Remedy:	Fuser open thermistor hot roll

Error code:	127
Display:	Contact the Service center. 127: Error
Description:	Fuser Error
Causes:	• Scanner motor defective (motor lead connected incorrectly) • MCU board defective (scanner motor control unit)
Remedy:	Fuser open thermistor BUR

Error code:	128
Display:	Service Call 128: Error
Description:	Fuser Error
Causes:	• Scanner motor defective • Overload on scanner mechanism • PSU-Eb board defective • MCU board defective (scanner motor control unit)
Remedy:	Fuser under temperature in standby - hot roll

OKI C710dn

Общие характеристики

Технология печати

Тип

Число страниц в месяц

Область применения

Размещение

Телефон

Печать фотографий

Копир

Сканер

Факс

Тип устройства

Макс. формат

Цветность печати

Принтер

Количество цветов

Прямая печать

Печать без полей

Пигментные чернила

Двусторонняя печать

Макс, разрешение для ч/б печати

Скорость ч/б печати

Время выхода первого отпечатка

Сканер

Стандарт WIA

Отправка изображения по e-mail

Стандарт TWAIN

Расходные материалы

Ресурс ч/б картриджа/тонера

Ресурс цветного картриджа/тонера

Ресурс фотобарабана

Количество картриджей

Печать на:

Плотность бумаги

Факс

Цветной

Телефон

Автоответчик

Стандарт DECT

Проводная трубка

Беспроводная трубка

АОН

Спикерфон

Caller ID

Шрифты и языки управления

Языки управления

Количество установленных шрифтов

Лотки

Подача бумаги

Вывод бумаги

Финишер

Сортер

Степлер

Брошюровщик

Сортировка со сдвигом

Электронная сортировка

Интерфейсы

RS-232

Устройство для чтения карт памяти

Инфракрасный порт

Bluetooth

Wi-Fi

FireWire (IEEE 1394)

LPT

Веб-интерфейс

USB

Ethernet (RJ-45)

Версия USB

Память/Процессор

Частота процессора

Процессор

Макс, объем памяти

Объем памяти

Дополнительная информация

Мин. системные требования

Экран

Поддержка ОС

Потребляемая мощность

Уровень шума

Error code:	142
Display:	Contact the Service center. 142: Error
Description:	Motor
Causes:	• Standard white plate defective, dirty • Moisture inside the scanner unit • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective
Remedy:	DC pick motor, over speed - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”.

Error code:	154
Display:	Service Call 154: Error
Description:	Jam at Registration Roller: Jam RR The Registration Sensor indicates that paper did not reach the sensor on time or that paper remains in the Registration Chute.
Causes:	• Registration Sensor, PL4.1.3 • Registration Sensor Actuator, PL4.1.1 • Registration Roller Assembly, PL4.2.1
Remedy:	1 Check the following for damage. • Registration Sensor Actuator, PL4.1.1 • Registration Roller Assembly, PL4.2.1 Is there any damage? Clean or replace as needed. Go to Step 2. 2 Test the Registration Sensor. Run the Service Diagnostics Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 3. 3 Check the Registration Sensor connection. Is the Registration Sensor connected to the harness? Go to Step 4. Reconnect. 4 Check all pins on the REGISNS Harness PL 4.1.4 for continuity. 1. Disconnect P/J181 and P/J18. 2. Check continuity between J181 <=> J18. Go to Step 5. Replace the Registration Sensor Harness. 5 Check the Registration Sensor signal. Block the Registration Sensor. Verify the voltage between P/J18-3 <=> P/J18-2 on the Engine Control Board is 0 VDC. Go to Step 6. Replace the Registration Sensor. 6 Test the Registration Clutch. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Registration Clutch test. Does the clutch function correctly? Go to Step 8. Go to Step 7. 7 Check the Registration Clutch resistance. Disconnect connector P/J192. Is the resistance between J192-1 <=> J192-2 less than 200ƒ¶? Go to Step 8. Replace the Registration Clutch (Part of the Registration Roller Assembly) 8 Check for +24 V to the Registration Clutch. 1. Disconnect P/J192. 2. Close the Interlock Switch while testing. Is there +24 V across P192-3 <=> ground? Replace the Registration Chute. Replace the Engine Control Board.

Error code:	155
Display:	Service Call 155: Error
Description:	Misfeed at Tray 1 (MPT): Jam T1 Paper fed from Tray 1 (MPT) did not reach the Registration Sensor on time.
Causes:	• Feed Roller Assembly MPT, PL5.3.20 • Interlock Switch, PL9.1.11 • Registration Sensor, PL4.1.3 • Feed Solenoid, PL5.3.9 • Registration Roller Assembly, PL4.2.1 • Main Drive Assembly, PL8.1.2
Remedy:	1 Check the following for evidence of fault or damage: • Feed Roller Assembly MPT, PL5.3.20 • Tray 1 (MPT) • Registration Sensor, PL4.1.3 • Main Drive Assembly, PL8.1.2 Remove any foreign objects or paper debris from the paper path. Is there any damage? Replace any damaged or excessively worn parts. Go to Step 2. 2 Test the Registration Sensor. Run the Service Diagnostics Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 3. 3 Check the Registration Sensor connection. Is the Registration Sensor connected to the harness? Go to Step 4. Connect the sensor. 4 Check all pins of the REGISNR Harness PL4.1.4 for continuity. 1. Disconnect P/J181 and P/J18. 2. Check continuity between J181 <=> J18. Go to Step 5. Replace the Registration Sensor Harness. 5 Check the Registration Sensor signal. Block the Registration Sensor. Verify the voltage between P/J18-3 <=> P/J18-2 on the Engine Control Board is 0 VDC. Replace Registration Sensor. Go to Step 6. 6 If possible, print a Test Print from Tray 1 (MPT). Does the Main Motor function properly? Go to Step 16 Go to Step 7 7 Test the Main Drive Assembly. Run the Service Diagnostics Main Motor test. Does the Main Motor turn? Replace the Engine Control Board. Go to Step 8. 8 Check for +24 V to the Main Drive Motor 1. Disconnect P/J481. 2. Close the Interlock Switch while testing. Is there +24 V across J481-10 <=> J481-8? Go to Step 12. Go to Step 9. 9 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the Interlock Switch function correctly? Go to Step 11. Go to Step 10. 10 Check for +5 V to the Interlock Switch Disconnect P/J161. Is there +5 V across P161-1 <=> P161-2? Replace the LVPS. Replace the Interlock Switch. 11 Check FAN/PHD/MOT Harness continuity. 1. Disconnect P/J48 and P/J481. 2. Check continuity between J48 <=> J481 Replace Main Drive Motor Replace FAN/ PHD/MOT Harness. 12 Check Turn Roller function. 1. Perform Steps 1 ~ 3 on. 2. Open and close the front door. 3. Observe the Turn Roller. Does the Turn Roller turn while the machine is warming up? Go to Step 16. Go to Step 13. 13 Test the Turn Clutch. 1. Run the Service Diagnostics Tray 1 (MPT) Turn Clutch test. 2. Close the Interlock Switch while testing. Does the Turn Clutch function normally? Check that the Clutch doesn’t slip. Check the gears for damage. Go to Step 14. 14 Check for +24 V to the Turn Clutch. 1. Disconnect P/J191. 2. Close the Interlock Switch while testing. Is there +24 V across P191-2 <=> ground? Go to Step 15. Replace the Engine Control Board. 15 Check Turn Clutch resistance. Disconnect P/J191. Is the resistance between J191-1 <=> J191-2 less than 200Ω? Go to Step 16. Replace the Turn Clutch (Part of the Registration Roller Assembly). 16 If possible, print a Test print from Tray 1 (MPT). Check the Feed Gear operation. Does the gear function normally? Check for damage or obstructions in the paper path. Go to Step 17. 17 Test the Feed Solenoid. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Tray 1 (MPT) Feed Solenoid test. Does the Feed Solenoid function normally? Check that the Feed Solenoid spring and stopper disengage correctly. Go to Step 18. 18 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J132 and P/J13. 2. Check continuity between J13 <=> P132. Go to Step 19. Replace the FRONT/DUP Harness Assembly. 19 Check Feed Solenoid resistance. Disconnect connector P/J132. Is the resistance between J132-1 <=> J132-2 less than 100Ω? Replace the Engine Control Board. Replace the Feed Solenoid.

Error code:	167
Display:	Service Call 167: Error
Description:	Motor
Causes:	Is the error message displayed? Does this error recur?
Remedy:	The incorrect configuration ID. See “Web oiler fuser kit installation” on page 4-88 to set configuration ID.

Error code:	168
Display:	Service Call 168: Error
Description:	Motor
Causes:	Is the error message displayed? Does this error recur?
Remedy:	Unknown manufacture type - perform “Motor Detect” on page 3-18. If you do not find the problem after performing the test, call your next level support.

Error code:	174
Display:	Contact the Service center. 174: Error
Description:	Motor
Causes:	Does this error recur?
Remedy:	Mirror motor lost lock - magenta - go to “Printhead diagnostics” on page 3-1. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” on page 3-1.

Error code:	175
Display:	Contact the Service center. 175: Error Note)
Description:	Motor
Causes:	Does this error recur?
Remedy:	Mirror motor lock not achieved - yellow - go to “Printhead diagnostics” on page 3-1. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” on page 3-1.

Error code:	190
Display:	Service Call 190: Error
Description:	System Memory Overflow
Remedy:	System Memory Overflow Power OFF/ON Replace CU PCB. (Replace EEPROM)

Error code:	209
Display:	Power On/off 209: DOWNLOAD ERROR
Description:	Custom Media Table Download Error Failed to download custom media table.
Remedy:	Failed to download custom media table. After turning ON the power again, try downloading again. (This process isn’t executed for regular operations, therefore, will not occur)

Error code:	230
Display:	Service Call 230: Error
Description:	Paper Jam Clear Paper Path Leave Job in Finisher area 5
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74.