OKI C9650hdtn

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

лазерная

Макс. формат

Число страниц в месяц

150000

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Тип	лазерный/светодиодный
Технология печати	лазерная
Область применения	большой офис
Макс. формат	A3
Телефон
Копир
Сканер
Факс
Печать фотографий
Тип устройства	Принтер
Размещение	настольный
Цветность печати	цветная
Число страниц в месяц	150 000
Принтер
Количество цветов	4
Прямая печать
Двусторонняя печать
Печать без полей
Пигментные чернила
Макс, разрешение для ч/б печати
По X	1 200
По Y	600
Скорость ч/б печати
A4	40
A3	21
A4	36
Скорость цветной печати
A3	19
Время выхода первого отпечатка
Ч/б	10,5
Цветн,	9
Сканер
Стандарт WIA
Стандарт TWAIN
Отправка изображения по e-mail
Расходные материалы
Количество картриджей	4
Печать на:
CD/DVD
Фотобумаге
Рулоне
Глянцевой бумаге
Конвертах
Карточках
Матовой бумаге
Этикетках
Пленках
Плотность бумаги
Максимальная	300
Минимальная	64
Факс
Цветной
Телефон
Беспроводная трубка
АОН
Caller ID
Автоответчик
Стандарт DECT
Спикерфон
Проводная трубка
Шрифты и языки управления
Языки управления
PDF
PostScript
PostScript 3
PCL 5c
PCL 6
PPDS
PostScript 2
PCL 5e
Количество установленных шрифтов
PostScript	136
PCL	86
Лотки
Подача бумаги
Максимальная	2 350
Стандартная	2 350
Вывод бумаги
Стандартный	700
Финишер
Электронная сортировка
Брошюровщик
Степлер
Сортировка со сдвигом
Сортер
Интерфейсы
Ethernet (RJ-45)
USB
LPT
Веб-интерфейс
Bluetooth
Wi-Fi
FireWire (IEEE 1394)
Инфракрасный порт
Устройство для чтения карт памяти
RS-232
Версия USB	2,0
Память/Процессор
Объем памяти	512
Процессор	PowerPC 750
Частота процессора	800
Емкость жесткого диска	40
Макс, объем памяти	1 024
Дополнительная информация
Поддержка ОС
Windows
Mac OS
Linux
DOS
Потребляемая мощность
При работе	1 500
В режиме ожидания	200
Уровень шума
При работе	54
В режиме ожидания	42
Габариты
Ширина	471
Высота	873
Вес	133
Глубина	654

Коды ошибок

001

002 ... 007

020 ... 024

025

030

031

032

036

037

040

041

042 ... 045

048

049

050

051

052

060

062

063

070

072

073 ... 075

081

096

097

104

105

106

111 ... 117

121

123

124

125

126

128

131 ... 134

140 ... 142

144 ... 147

150 ... 153

154

155

160 ... 163

167

168

169

170 ... 175

172 ... 176

173 ... 177

179

180 ... 186

187

188

189

190

200 ... 202

203, 204, 207, 214

209

220

230

231

240 ... 248

910 ... 914

917

918

919

920

921

922

923

924

925

926

927

928

929

930

931

932

933

934

935

936

940

F0C, F0D, FFE, FFF

Описание

Парткод

Название

OKI Сборник отработанного тонера

OKI Блок фотобарабана желтый

OKI Блок фотобарабана пурпурный

OKI Блок фотобарабана голубой

OKI Блок фотобарабана черный

OKI (42918913) Тонер-картридж желтый

OKI (42918914) Тонер-картридж пурпурный

OKI (42918915) Тонер-картридж голубой

OKI (42918916) Тонер-картридж черный

OKI Ремень переноса изображения

OKI Печка 220V

OKI Скрепки для финишера в картриджах

OKI Комплект тонер-картриджей

Error code:	001
Display:	Service Call 001: Error
Description:	Leading edge of the recording paper fails to reach the Timing Sensor. (1st Cassette)
Causes:	Recording paper jam. Timing Sensor abnormal.
Remedy:	Is the error display reproducible? Power OFF/ON Replace CU PCB. (Must replace EEPROM)

Error code:	002 ... 007
Display:	Service Call Power off/on nnn: Fatal Error PC: nnnnnnnn LR: nnnnnnnn FR: nnnnnnnn 002: Error to 007: Error
Description:	This stems from a variety of causes.For analyzing causes, record three numbers (called program counting value) indicated below LCD column and a printer firmware version.
Causes:	Does this error message reappear?
Remedy:	Record three digital numbers below LCD column. Restart with OFF/ON? Does an error occur in a particular print data? Is the error display reproducible? Is the error display reproducible? Is the error display reproducible? Notify three digital numbers below LCD column and F/W version. Check if it occurs depending on a print data. Request for print data investigation. Change RAM DIMM or ROM DIMM. Replace CU PCB. (Must replace EEPROM) Initialize EEPROM. Re-execute Network setup, such as user setup etc. for use. Change the printer.

Error code:	020 ... 024
Display:	Service Call 020: Error or 024: Error
Description:	CU ROM Hash Check Error 1
Causes:	Is the Slot A ROM DIMM mounted properly? Is operations restored by replacing the Slot A ROM DIMM?
Remedy:	Is the Slot A ROM DIMM mounted properly? Is operations restored by replacing the Slot A ROM DIMM? Remount Slot A ROM DIMM Replace Slot A ROM DIMM. Replace CU PCB. (Must replace EEPROM)

Error code:	025
Display:	Service Call 025: Error
Description:	CU Font ROM Hash Error1 Detected a Font Data hash check error.
Causes:	Detected a Font ROM_DIMM hash check error. (Japan Model only)
Remedy:	Detected a Font Data hash check error. (Japan Model only) Replace CU PCB. (Must replace EEPROM)

Error code:	030
Display:	Service Call 030: Error
Description:	CU Slot1 DIMM RAM Check Error
Causes:	Is subject RAM DIMM set properly? Is error recovered by replacing subject ROM DIMM?
Remedy:	Reset subject RAM DIMM. Replace RAM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	031
Display:	Service Call 031: Error
Description:	CU Slot2 DIMM RAM Check Error
Causes:	Is subject RAM DIMM set properly? Is error recovered by replacing subject ROM DIMM?
Remedy:	Reset subject RAM DIMM. Replace RAM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	032
Display:	Service Call 032: Error
Description:	CU Slot3 DIMM RAM Check Error
Causes:	Is subject RAM DIMM set properly? Is error recovered by replacing subject ROM DIMM?
Remedy:	Reset subject RAM DIMM. Replace RAM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	036
Display:	Service Call 036: Error
Description:	Slot2 RAM Spec Error. The CU RAM Slot2 DIMM specification is not supported.
Causes:	Is RAM DIMM genuine? Is subject RAM DIMM gap setting proper? Is error recovered by replacing subject ROM DIMM?
Remedy:	Use genuine RAM DIMM. Reset subject RAM DIMM. Replace RAM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	037
Display:	Service Call 037: Error
Description:	Slot3 RAM Spec Error. The CU RAM Slot3 DIMM specification is notsupported.
Causes:	Is RAM DIMM genuine? Is subject RAM DIMM gap setting proper? Is error recovered by replacing subject ROM DIMM?
Remedy:	Use genuine RAM DIMM. Reset subject RAM DIMM. Replace RAM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	040
Display:	Service Call 040: Error
Description:	CU EEPROM Error
Causes:	Is error recovered by replacing EEPROM on CU board?
Remedy:	Replace EEPROM. (Recover user environment.) Replace TIG board. (Replace EEPROM)

Error code:	041
Display:	Service Call 041: Error
Description:	CU Flash Error Flash ROM error on CU board.
Causes:	Does error display reappear?
Remedy:	Replace TIG board. (Replace EEPROM.)

Error code:	048
Display:	Service Call 048: Error
Description:	CU ROM for PS+PCL was set in Non-PS device.
Causes:	Is proper program ROM set?
Remedy:	Replace program ROM DIMM. Replace with proper program ROM DIMM.

Error code:	049
Display:	Service Call 049: Error
Description:	CU type mismatch CU ROM does not match with the device.
Causes:	Is proper program ROM set?
Remedy:	Replace program ROM DIMM. Replace with proper program ROM DIMM.

Error code:	050
Display:	Service Call 050: Error
Description:	Operater Panel Error
Causes:	Does error display reappear?
Remedy:	Refer to no LCD display flow chart.

Error code:	051
Display:	Service Call 051: Error
Description:	CU Fan Error Abnormal CPU cooling fan on CU board.
Causes:	Is connector set properly on CU board? Is error recovered by replacing fan?
Remedy:	Connect properly. Replace fan. Replace TIG board. (Replace EEPROM.)

Error code:	104
Display:	Service Call 104: Error
Description:	Developer Motor Failure The Developer Motor rotation signal indicates that the motor is no longer operational.
Causes:	• Developer Drive Assembly, PL8.1.1 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Check the Developer Drive Assembly for damage. Are any parts of the Developer Drive Assembly damaged or excessively worn? Replace the Developer Drive Assy. Go to Step 2. 2 Check the Developer Motor connection. Is P/J491 connected to the harness? Go to Step 3. Reconnect the Developer Motor. 3 Test the Developer Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Developer Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Developer Motor. Is the +24 V across P/J491-1 <=> P/J 481-5? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J491. 2. Check continuity between J48 <=> J491. Replace the Engine Control Board. Replace the FAN/PHD/MOT Harness.

Error code:	105
Display:	Service Call 105: Error
Description:	Main Motor Failure The Main Motor rotation signal indicates that the motor is no longer operational.
Causes:	• Main Drive Assembly, PL8.1.2 • Engine Control Board, PL9.1.16 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Check the Main Drive Assembly for damage. Are any parts damaged? Replace the Main Drive Assembly. Go to Step 2. 2 Check the Main Motor connection. Is P/J481 connected to the harness? Go to Step 3. Reconnect the Main Motor. 3 Test the Main Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Main Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Main Motor. Is there +24 V across P/J481-10 <=> P/J 481-8? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the FAN/PHD/MOT Harness, PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J481. 2. Check continuity between J48 <=> J481. Replace the Engine Control Board. Replace the FAN/PHD/MOT Harness.

Error code:	106
Display:	Service Call 106: Error
Description:	Motor Failure One of the primary drive motors has failed.
Causes:	• Main Drive Assembly, PL8.1.2 • Developer Drive Assembly, PL8.1.1 • Fuser Drive Assembly, PL5.2.25 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11
Remedy:	1 Check the motors. Run the Service Diagnostics motor tests to determine the failed part. Is the failed part the Main Drive Motor? Go to. Test the Fuser Motor. 2 Is the failed part the Fuser Drive Motor? Go to. Test the Developer Motor. 3 Is the failed part the Developer Drive Motor? Go to. Replace the Engine Control Board.

Error code:	111 ... 117
Display:	Service Call 111: Error to 117: Error
Description:	An optional unit for another model was detected. 111: Duplex unit 112: 2nd Tray 113: 3rd Tray 114: 4thTray 115: 5th Tray 116: Finisher 117: Inverter
Causes:	Is the proper optional unit for that model mounted?
Remedy:	Is the proper optional unit for that model mounted? Mount the proper optional unit. Check the connection. Then turn ON the power again. Replace the unit if operations is not restored.

Error code:	052
Display:	Power Off/on 052: Error
Description:	Image Processor Driver Error
Causes:	Does this error message reappear?
Remedy:	Is the error display reproducible? Power OFF/ON Replace CU PCB. (Replace EEPROM)

Error code:	060
Display:	Power Off/on 060: Error
Description:	Printer Cover is open.
Causes:	Cover is not firmly closed. Connectors are not firmly connected.
Remedy:	Is the error display reproducible? Power OFF/ON Replace CU PCB. (Replace EEPROM)

Error code:	062
Display:	Power Off/on 062: Error
Description:	USB Drive Error
Causes:	Is the error display reproducible? Is the Network PCB properly mounted?
Remedy:	Is the error display reproducible? Is the Network PCB properly mounted? Power OFF/ON Replace CU PCB. (Replace EEPROM)

Error code:	063
Display:	Service Call 063: Error
Description:	Network comm. Error Abnormal H/W I/F between CU-NIC.
Causes:	Is network board set properly? Is error recovered by replacing network board?
Remedy:	Set properly. Replace Network. Replace TIG board. (Replace EEPROM.)

Error code:	070
Display:	Service Call 070: Error
Description:	CANT_HAPPEN PS firmware fault detected.
Causes:	Confirm that error is recovered by turning power OFF/ON.
Remedy:	Replace TIG board. (Replace EEPROM.)

Error code:	072
Display:	Service Call 072: Error
Description:	Engine communication error I/F error between PU-CU.
Causes:	Is CU assembly set properly? Is error recovered by replacing TIG board?
Remedy:	Set properly. Replace TIG board. (Replace EEPROM.) Replace PU board.

Error code:	081
Display:	Service Call 081: Error
Description:	Parameter Match Check Error
Remedy:	Normal Read/Write not possible with EEPROM or Flash. If the condition does not change replace CU PCB.

Error code:	096
Display:	Service Call 096: Error
Description:	Finisher Unrestorable Error
Causes:	Is the error display reproducible?
Remedy:	Is the error display reproducible? If turning OFF and ON the power again does not correct the problem, maintenance by a servicing personnel is necessary.

Error code:	097
Display:	Service Call 097: Error
Description:	Inverter power supply Error
Causes:	Is the error display reproducible?
Remedy:	Is the error display reproducible? If turning OFF and ON the power again does not correct the problem, maintenance by a servicing personnel is necessary.

Error code:	121
Display:	Service Call 121: Error
Description:	Fuser Error
Causes:	Is cable between PU board andhighvoltage power LSI connected properly?
Remedy:	Wrong fuser lamp - BUR - replace the fuser assembly

OKI C9650hdtn

Общие характеристики

Тип

Технология печати

Область применения

Макс. формат

Телефон

Копир

Сканер

Факс

Печать фотографий

Тип устройства

Размещение

Цветность печати

Число страниц в месяц

Принтер

Количество цветов

Прямая печать

Двусторонняя печать

Печать без полей

Пигментные чернила

Макс, разрешение для ч/б печати

Скорость ч/б печати

Скорость цветной печати

Время выхода первого отпечатка

Сканер

Стандарт WIA

Стандарт TWAIN

Отправка изображения по e-mail

Расходные материалы

Количество картриджей

Печать на:

Плотность бумаги

Факс

Цветной

Телефон

Беспроводная трубка

АОН

Caller ID

Автоответчик

Стандарт DECT

Спикерфон

Проводная трубка

Шрифты и языки управления

Языки управления

Количество установленных шрифтов

Лотки

Подача бумаги

Вывод бумаги

Финишер

Электронная сортировка

Брошюровщик

Степлер

Сортировка со сдвигом

Сортер

Интерфейсы

Ethernet (RJ-45)

USB

LPT

Веб-интерфейс

Bluetooth

Wi-Fi

FireWire (IEEE 1394)

Инфракрасный порт

Устройство для чтения карт памяти

RS-232

Версия USB

Память/Процессор

Объем памяти

Процессор

Частота процессора

Емкость жесткого диска

Макс, объем памяти

Дополнительная информация

Поддержка ОС

Потребляемая мощность

Уровень шума

Габариты

Ширина

Высота

Error code:	123
Display:	Service Call 123: Error
Description:	Finisher Set Clamp Failure, Code 123 The set clamp home sensor did not turn on within 2 seconds after the set clamp started operation.
Causes:	• Set Clamp Solenoid • Finisher Control Board
Remedy:	1 1. Check the Set Clamp home sensor in diagnostics. 2. Does the value change from H to L while rotating the actuator? Go to step 2. Use the transmissive Sensor procedure to diagnose and repair the sensor. 2 Does the solenoid energize when running the Set Clamp Paddle test in diagnostics? Go to step 3. Go to step 4. 3 1. Run the Eject Forward Test and then the Eject Release Test in diagnostics. 2. Does the set clamp paddle turn once? Replace the finisher control board. Go to step 4. 4 Is +24 VDC present at P848A-10? Go to step 5. Go to step 6. 5 Is +24 VDC present at P848A-11? Replace the finisher control board. Replace the set clamp solenoid. 6 Is +24 VDC present at test point 9 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit.

Error code:	124
Display:	Service Call 124: Error
Description:	Finisher Communication Failure, Code 124
Remedy:	There are no diagnostic routines for problems involving serial communications. It is recommended that you address the following assemblies in this order: • Finisher Control Board • Engine Control Board • Perform continuity checks on any wiring harnesses involved.

Error code:	125
Display:	Service Call 125: Error
Description:	Finisher Staple Mode Logic Failure, Code 125
Remedy:	There are no diagnostic routines for problems involving serial communications. It is recommended that you address the following assemblies in this order: • Stapler Assembly • Engine Control Board • Perform continuity checks on any wiring harnesses involved.

Error code:	126
Display:	Turn power OFF and wait 126: Dew error
Description:	Fuser Error
Causes:	Sensor dew error detected.
Remedy:	Fuser open thermistor hot roll

Error code:	128
Display:	Service Call 128: Error
Description:	Fuser Error
Causes:	• Scanner motor defective • Overload on scanner mechanism • PSU-Eb board defective • MCU board defective (scanner motor control unit)
Remedy:	Fuser under temperature in standby - hot roll

Error code:	154
Display:	Service Call 154: Error
Description:	Jam at Registration Roller: Jam RR The Registration Sensor indicates that paper did not reach the sensor on time or that paper remains in the Registration Chute.
Causes:	• Registration Sensor, PL4.1.3 • Registration Sensor Actuator, PL4.1.1 • Registration Roller Assembly, PL4.2.1
Remedy:	1 Check the following for damage. • Registration Sensor Actuator, PL4.1.1 • Registration Roller Assembly, PL4.2.1 Is there any damage? Clean or replace as needed. Go to Step 2. 2 Test the Registration Sensor. Run the Service Diagnostics Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 3. 3 Check the Registration Sensor connection. Is the Registration Sensor connected to the harness? Go to Step 4. Reconnect. 4 Check all pins on the REGISNS Harness PL 4.1.4 for continuity. 1. Disconnect P/J181 and P/J18. 2. Check continuity between J181 <=> J18. Go to Step 5. Replace the Registration Sensor Harness. 5 Check the Registration Sensor signal. Block the Registration Sensor. Verify the voltage between P/J18-3 <=> P/J18-2 on the Engine Control Board is 0 VDC. Go to Step 6. Replace the Registration Sensor. 6 Test the Registration Clutch. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Registration Clutch test. Does the clutch function correctly? Go to Step 8. Go to Step 7. 7 Check the Registration Clutch resistance. Disconnect connector P/J192. Is the resistance between J192-1 <=> J192-2 less than 200ƒ¶? Go to Step 8. Replace the Registration Clutch (Part of the Registration Roller Assembly) 8 Check for +24 V to the Registration Clutch. 1. Disconnect P/J192. 2. Close the Interlock Switch while testing. Is there +24 V across P192-3 <=> ground? Replace the Registration Chute. Replace the Engine Control Board.

Error code:	155
Display:	Service Call 155: Error
Description:	Misfeed at Tray 1 (MPT): Jam T1 Paper fed from Tray 1 (MPT) did not reach the Registration Sensor on time.
Causes:	• Feed Roller Assembly MPT, PL5.3.20 • Interlock Switch, PL9.1.11 • Registration Sensor, PL4.1.3 • Feed Solenoid, PL5.3.9 • Registration Roller Assembly, PL4.2.1 • Main Drive Assembly, PL8.1.2
Remedy:	1 Check the following for evidence of fault or damage: • Feed Roller Assembly MPT, PL5.3.20 • Tray 1 (MPT) • Registration Sensor, PL4.1.3 • Main Drive Assembly, PL8.1.2 Remove any foreign objects or paper debris from the paper path. Is there any damage? Replace any damaged or excessively worn parts. Go to Step 2. 2 Test the Registration Sensor. Run the Service Diagnostics Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 3. 3 Check the Registration Sensor connection. Is the Registration Sensor connected to the harness? Go to Step 4. Connect the sensor. 4 Check all pins of the REGISNR Harness PL4.1.4 for continuity. 1. Disconnect P/J181 and P/J18. 2. Check continuity between J181 <=> J18. Go to Step 5. Replace the Registration Sensor Harness. 5 Check the Registration Sensor signal. Block the Registration Sensor. Verify the voltage between P/J18-3 <=> P/J18-2 on the Engine Control Board is 0 VDC. Replace Registration Sensor. Go to Step 6. 6 If possible, print a Test Print from Tray 1 (MPT). Does the Main Motor function properly? Go to Step 16 Go to Step 7 7 Test the Main Drive Assembly. Run the Service Diagnostics Main Motor test. Does the Main Motor turn? Replace the Engine Control Board. Go to Step 8. 8 Check for +24 V to the Main Drive Motor 1. Disconnect P/J481. 2. Close the Interlock Switch while testing. Is there +24 V across J481-10 <=> J481-8? Go to Step 12. Go to Step 9. 9 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the Interlock Switch function correctly? Go to Step 11. Go to Step 10. 10 Check for +5 V to the Interlock Switch Disconnect P/J161. Is there +5 V across P161-1 <=> P161-2? Replace the LVPS. Replace the Interlock Switch. 11 Check FAN/PHD/MOT Harness continuity. 1. Disconnect P/J48 and P/J481. 2. Check continuity between J48 <=> J481 Replace Main Drive Motor Replace FAN/ PHD/MOT Harness. 12 Check Turn Roller function. 1. Perform Steps 1 ~ 3 on. 2. Open and close the front door. 3. Observe the Turn Roller. Does the Turn Roller turn while the machine is warming up? Go to Step 16. Go to Step 13. 13 Test the Turn Clutch. 1. Run the Service Diagnostics Tray 1 (MPT) Turn Clutch test. 2. Close the Interlock Switch while testing. Does the Turn Clutch function normally? Check that the Clutch doesn’t slip. Check the gears for damage. Go to Step 14. 14 Check for +24 V to the Turn Clutch. 1. Disconnect P/J191. 2. Close the Interlock Switch while testing. Is there +24 V across P191-2 <=> ground? Go to Step 15. Replace the Engine Control Board. 15 Check Turn Clutch resistance. Disconnect P/J191. Is the resistance between J191-1 <=> J191-2 less than 200Ω? Go to Step 16. Replace the Turn Clutch (Part of the Registration Roller Assembly). 16 If possible, print a Test print from Tray 1 (MPT). Check the Feed Gear operation. Does the gear function normally? Check for damage or obstructions in the paper path. Go to Step 17. 17 Test the Feed Solenoid. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Tray 1 (MPT) Feed Solenoid test. Does the Feed Solenoid function normally? Check that the Feed Solenoid spring and stopper disengage correctly. Go to Step 18. 18 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J132 and P/J13. 2. Check continuity between J13 <=> P132. Go to Step 19. Replace the FRONT/DUP Harness Assembly. 19 Check Feed Solenoid resistance. Disconnect connector P/J132. Is the resistance between J132-1 <=> J132-2 less than 100Ω? Replace the Engine Control Board. Replace the Feed Solenoid.

Error code:	167
Display:	Service Call 167: Error
Description:	Motor
Causes:	Is the error message displayed? Does this error recur?
Remedy:	The incorrect configuration ID. See “Web oiler fuser kit installation” on page 4-88 to set configuration ID.

Error code:	168
Display:	Service Call 168: Error
Description:	Motor
Causes:	Is the error message displayed? Does this error recur?
Remedy:	Unknown manufacture type - perform “Motor Detect” on page 3-18. If you do not find the problem after performing the test, call your next level support.

Error code:	169
Display:	Service Call 169: Error
Description:	Motor
Causes:	Is the error message displayed? Does this error recur?
Remedy:	Mirror motor lock not achieved - black - go to “Printhead diagnostics” on page 3-1. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” on page 3-1.