Ricoh Aficio 1224CG
Рейтинг
Модули
ELECTRICAL SECTION 2
ELECTRICAL SECTION 4
FUSING UNIT 2
FUSING UNIT 3
ELECTRICAL SECTION 1
RESISTRATION
Drive Section 1
VERTICAL TRANSFER 1
DEVELOPMENT UNIT
ELECTRICAL SECTION 3
Paper exit
FUSING UNIT 1
ELECTRICAL SECTION 5
DRIVE SECTION 3
PCU UNIT
DRIVE SECTION 2
VERTICAL TRANSFER 2
SCANNER UNIT 2
EXTERIOR 1
PAPER TRAY 1
SCANNER UNIT 1
LASER UNIT
EXTERIOR 2
OPERATION PANEL
PAPER TRAY 2
FRAME SECTION
VERTICAL TRANSFER 3
Детали SCANNER UNIT 1
| Деталь: | Cooling Duct - Scanner Assembly |
| Парткод: | B051 5970 |
| Деталь: | Seal - Duct |
| Парткод: | B051 5965 |
| Деталь: | Fan Motor - DC2.88W |
| Парткод: | AX64 0138 |
| Деталь: | Stay - Upper Guide Plate |
| Парткод: | B051 5878 |
| Деталь: | Pump |
| Парткод: | B051 4358 |
| Деталь: | Oil Supply Tube |
| Парткод: | B051 4355 |
| Деталь: | Silicone Oil Nozzle |
| Парткод: | B051 4360 |
| Деталь: | Nozzle Bracket |
| Парткод: | B051 4359 |
| Деталь: | Pumping Tube |
| Парткод: | B051 4354 |
| Деталь: | Duct - Fusing Assembly |
| Парткод: | B051 5853 |
| Деталь: | Seal - Duct |
| Парткод: | B051 5966 |
| Деталь: | Duct Exhaust Bracket - Development |
| Парткод: | B051 5978 |
| Деталь: | Fan Motor - DC6.4W |
| Парткод: | AX65 0034 |
| Деталь: | Stay - Duct Exhaust |
| Парткод: | B051 5893 |
| Деталь: | EXIOB Harness |
| Парткод: | B052 5433 |
| Деталь: | EXIOB Board |
| Парткод: | B051 5120 |
| Деталь: | Bracket - EXIO Board |
| Парткод: | B051 5855 |
| Деталь: | Duct - Lower Charge |
| Парткод: | B051 5892 |
| Деталь: | Cap - Oil Tank Assembly |
| Парткод: | B051 4361 |
| Деталь: | Duct Shield |
| Парткод: | G070 1083 |
| Деталь: | TUBE |
| Парткод: | B051 4356 |
| Деталь: | Oil Tank |
| Парткод: | B051 4351 |
| Деталь: | Oil Tank Bracket |
| Парткод: | B051 4352 |
| Деталь: | Front Exhaust Duct - Development |
| Парткод: | B051 5976 |
| Деталь: | Rear Exhaust Duct - Development |
| Парткод: | B051 5973 |
| Деталь: | Fan Motor - DC6.4W |
| Парткод: | B051 5971 |
| Деталь: | Cooling Duct - Left Development |
| Парткод: | B051 5845 |
| Деталь: | Cooling Duct - Right Development |
| Парткод: | B051 5846 |
| Деталь: | Duct - Upper Charge |
| Парткод: | B051 5894 |
| Деталь: | Rear Link Lever |
| Парткод: | G070 5573 |
| Деталь: | Link Lever - Rear Right |
| Парткод: | G070 5574 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | G070 5575 |
| Деталь: | Link Outer Lever |
| Парткод: | G070 5564 |
| Деталь: | Link Middle Lever - Left |
| Парткод: | G070 5570 |
| Деталь: | Right Tension Spring |
| Парткод: | G070 5566 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0014 |
| Деталь: | Lower Case - Safety Switch |
| Парткод: | G070 5561 |
| Деталь: | Right Link - Safety Switch |
| Парткод: | G070 5568 |
| Деталь: | Right Tension Spring |
| Парткод: | G070 5565 |
| Деталь: | Link Middle Lever |
| Парткод: | G070 5563 |
| Деталь: | IOB Harness |
| Парткод: | B052 5415 |
| Деталь: | Door Switch Harness |
| Парткод: | B052 5420 |
| Деталь: | Upper Case - Safety Switch |
| Парткод: | G070 5562 |
| Деталь: | Bracket - Total Counter |
| Парткод: | B051 5860 |
| Деталь: | Bracket - Main Switch |
| Парткод: | B051 5861 |
| Деталь: | Harness - Main Switch |
| Парткод: | B052 5464 |
| Деталь: | Rail - Left Front |
| Парткод: | B051 1111 |
| Деталь: | Left Front Bracket - Grip |
| Парткод: | B051 1078 |
| Деталь: | GRIP |
| Парткод: | G070 1051 |
| Деталь: | Left Cover Hinge |
| Парткод: | G070 1075 |
| Деталь: | Front Lower Guide |
| Парткод: | G070 2335 |
| Деталь: | Heater Assembly (120V) |
| Парткод: | B051 2547 |
| Деталь: | Heater Assembly (230V) |
| Парткод: | B051 2548 |
| Деталь: | TOTAL COUNTER |
| Парткод: | AX31 0043 |
| Деталь: | COVER HINGE |
| Парткод: | G070 1074 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0024 |
| Деталь: | Holder - Paper Tray |
| Парткод: | G060 2801 |
| Деталь: | Right Grip |
| Парткод: | G070 1067 |
| Деталь: | Grip Bracket - Front Right |
| Парткод: | G070 1053 |
| Деталь: | Total Counter 2nd |
| Парткод: | AX31 0038 |
| Деталь: | Stopper - Link |
| Парткод: | B051 1128 |
| Деталь: | Cushion - Safety Switch |
| Парткод: | G070 5576 |
| Деталь: | Fusing Unit Assembly (120V) |
| Парткод: | B051 4025 |
| Деталь: | Fusing Unit Assembly (230V) |
| Парткод: | B051 4030 |
| Деталь: | Fusing Unit - Fusing Belt Assembly |
| Парткод: | G070 4005 |
| Деталь: | Thermistor Holder |
| Парткод: | G070 4051 |
| Деталь: | Fusing Lamp - 120V 770W |
| Парткод: | AX44 0161 |
| Деталь: | Fusing Lamp - 230V 770W |
| Парткод: | AX44 0162 |
| Деталь: | Fusing Lamp - 120V 350W |
| Парткод: | AX43 0078 |
| Деталь: | Fusing Lamp - 230V 350W |
| Парткод: | AX43 0079 |
| Деталь: | Pressure Thermistor |
| Парткод: | AW10 0061 |
| Деталь: | Oil End Sensor |
| Парткод: | G024 4740 |
| Деталь: | Fusing Knob |
| Парткод: | G070 4147 |
| Деталь: | Spring - Oiling Roller |
| Парткод: | AA06 3865 |
| Деталь: | Bushing -4x8x8.5 |
| Парткод: | AE031054 |
| Деталь: | Bushing -4x9x13 |
| Парткод: | AE03 1055 |
| Деталь: | Rubber Shield - 4x8x3 |
| Парткод: | G070 4087 |
| Деталь: | Gear - 36Z |
| Парткод: | AB01 1436 |
| Деталь: | BELT TENSION SPRING |
| Парткод: | AA06 0875 |
| Деталь: | Belt Tension Lever |
| Парткод: | G070 4116 |
| Деталь: | Front Stopper - Oil Supply Unit |
| Парткод: | G070 4114 |
| Деталь: | Sensor Holder |
| Парткод: | G070 4118 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Rear Stopper - Oil Supply Unit |
| Парткод: | G070 4152 |
| Деталь: | Ball Bearing - 20x32x7 |
| Парткод: | AE03 0050 |
| Деталь: | Pressure Roller - Assembly |
| Парткод: | AE02 0119 |
| Деталь: | Gear - 47Z |
| Парткод: | AB01 1435 |
| Деталь: | Idler Gear - 28Z/35Z |
| Парткод: | AB01 7570 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | G070 4052 |
| Деталь: | Lower Pressure Roller Stay |
| Парткод: | G070 4050 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0876 |
| Деталь: | Front Oil Tank Absorber |
| Парткод: | G070 4073 |
| Деталь: | Oil Tank - Pressure Sub-unit |
| Парткод: | G070 4069 |
| Деталь: | Rear Oil Pan - Pressure Unit |
| Парткод: | G070 4063 |
| Деталь: | Rear Oil Absorber |
| Парткод: | G070 4066 |
| Деталь: | Spring Plate - Pressure Unit |
| Парткод: | G070 4064 |
| Деталь: | Front Oil Pan - Pressure Unit |
| Парткод: | G070 4062 |
| Деталь: | Front Oil Absorber |
| Парткод: | G070 4065 |
| Деталь: | Oil Tank Absorber - Long |
| Парткод: | G070 4074 |
| Деталь: | Oil Supply Roller - Oil Supply |
| Парткод: | AE04 0050 |
| Деталь: | Oil Apply Roller - Oil Supply |
| Парткод: | AE04 0037 |
| Деталь: | Heat Insulation - Sensor Holder |
| Парткод: | G070 4120 |
| Деталь: | Front Oil Tank Absorber |
| Парткод: | G070 4072 |
| Деталь: | Roller Clutch - 4mm |
| Парткод: | B051 4138 |
| Деталь: | Cleaning Roller - Pressure Sub-Unit |
| Парткод: | B051 4119 |
| Деталь: | Bushing - Cleaning Roller |
| Парткод: | B051 4116 |
| Деталь: | Torsion Spring - Rear |
| Парткод: | B051 4118 |
| Деталь: | Torsion Spring - Front |
| Парткод: | B051 4120 |
| Деталь: | Oil Supply Unit |
| Парткод: | B051 4300 |
| Деталь: | Cover - Oil Supply Unit |
| Парткод: | B051 4301 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 0915 |
| Деталь: | Felt Wick - Assembly |
| Парткод: | B051 4302 |
| Деталь: | Oil Tank - Oil Application Unit |
| Парткод: | B051 4305 |
| Деталь: | Holder - Oil Tank |
| Парткод: | G070 4212 |
| Деталь: | Positioning Sensor - Overflow |
| Парткод: | B051 4306 |
| Деталь: | Dual Faces Tepe |
| Парткод: | B051 4307 |
| Деталь: | Sponge Roller |
| Парткод: | G070 4217 |
| Деталь: | SPRING |
| Парткод: | AA06 3882 |
| Деталь: | Bushing - Sponge Roller |
| Парткод: | G070 4219 |
| Деталь: | Spring - Fusing Cleaning Roller |
| Парткод: | AA06 0880 |
| Деталь: | Bracket Assembly |
| Парткод: | G070 4119 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | B051 4309 |
| Деталь: | Roller - Oil Supply Roller |
| Парткод: | G070 4231 |
| Деталь: | Fusing Cleaning Roller |
| Парткод: | G070 4218 |
| Деталь: | Bushing - 4x6x5.5 |
| Парткод: | G070 4220 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Oil Tank Guide |
| Парткод: | B051 4313 |
| Деталь: | Cleaning Roller Cover |
| Парткод: | G070 4225 |
| Деталь: | Bracket Pin - Rear |
| Парткод: | AA14 9668 |
| Деталь: | Bracket - Fusing Cleaning Roller |
| Парткод: | G070 4216 |
| Деталь: | Bracket - Fusing Sponge Roller |
| Парткод: | G070 4204 |
| Деталь: | Bracket Pin - Front |
| Парткод: | AA14 9667 |
| Деталь: | Stay - Middle Guide Plate |
| Парткод: | B051 5862 |
| Деталь: | Upper Cover - Control Board |
| Парткод: | B051 5819 |
| Деталь: | Cover - Control Board |
| Парткод: | B051 5869 |
| Деталь: | Bracket - Controller Board: |
| Парткод: | B051 5851 |
| Деталь: | Bracket - I/O Board |
| Парткод: | B051 5854 |
| Деталь: | I/O Board |
| Парткод: | B051 5107 |
| Деталь: | Harness - Intermadediate Transfer |
| Парткод: | B052 5411 |
| Деталь: | Harness - EXIOB/IOB |
| Парткод: | B052 5401 |
| Деталь: | Sensor Harness |
| Парткод: | B052 5405 |
| Деталь: | Harness - Fusing Unit Motor |
| Парткод: | B052 5404 |
| Деталь: | Harness - Development Motor |
| Парткод: | B052 5418 |
| Деталь: | Harness - Main Motor |
| Парткод: | B052 5417 |
| Деталь: | Harness - Paper Side Sensor |
| Парткод: | B052 5408 |
| Деталь: | IOB Harness |
| Парткод: | B052 5458 |
| Деталь: | Bracket - Fan Assembly |
| Парткод: | B051 5492 |
| Деталь: | Fan Motor - DC2.4W |
| Парткод: | AX64 0103 |
| Деталь: | Ground Plate - Application |
| Парткод: | B051 5899 |
| Деталь: | Cover - BICU |
| Парткод: | B051 5896 |
| Деталь: | Cover - Application |
| Парткод: | B051 5880 |
| Деталь: | Cover - IC Card |
| Парткод: | B051 5881 |
| Деталь: | Bracket - NIC |
| Парткод: | B051 5889 |
| Деталь: | Cover - Application |
| Парткод: | B051 5868 |
| Деталь: | SDRAM-DIMM128MB |
| Парткод: | B051 5169 |
| Деталь: | Controller board |
| Парткод: | B051 5159 |
| Деталь: | BICU Harness |
| Парткод: | B052 5449 |
| Деталь: | BICU Harness |
| Парткод: | B052 5477 |
| Деталь: | BICU Board Assembly |
| Парткод: | B051 5207 |
| Деталь: | BICU/EXIOB Harness |
| Парткод: | B052 5406 |
| Деталь: | HDD Harness |
| Парткод: | B514 5951 |
| Деталь: | POWER CABLE |
| Парткод: | G315 5952 |
| Деталь: | SCREW |
| Парткод: | G315 5539 |
| Деталь: | Left Bracket |
| Парткод: | G315 5537 |
| Деталь: | Right Bracket |
| Парткод: | G315 5536 |
| Деталь: | HDD40GB |
| Парткод: | B514 5950 |
| Деталь: | Rubber Cushion |
| Парткод: | AA16 1125 |
| Деталь: | Hexagonal Head Bolt - 6-32uncx4 |
| Парткод: | AA14 3525 |
| Деталь: | Fan Harness |
| Парткод: | B052 5440 |
| Деталь: | Fan Harness |
| Парткод: | B052 5443 |
| Деталь: | Gasket - HDD |
| Парткод: | B514 5501 |
| Деталь: | NV-RAM - Minus Counter |
| Парткод: | B051 9099 |
| Деталь: | Slide Rail |
| Парткод: | G070 6145 |
| Деталь: | Grounding Plate - Slide Rail |
| Парткод: | G070 6175 |
| Деталь: | Slide Rail Stopper |
| Парткод: | G070 6157 |
| Деталь: | Left Lower Rail |
| Парткод: | G070 6150 |
| Деталь: | Power Supply Unit Cover |
| Парткод: | G070 6158 |
| Деталь: | Right Lower Rail |
| Парткод: | G070 6152 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA082101 |
| Деталь: | Roller - Vertical Transport |
| Парткод: | AF02 0558 |
| Деталь: | Gear - 28Z |
| Парткод: | AB01 1225 |
| Деталь: | Gap Gear Guide |
| Парткод: | G0701197 |
| Деталь: | BUSHING |
| Парткод: | AA08 0271 |
| Деталь: | Registration Drive Roller |
| Парткод: | AF02 0536 |
| Деталь: | Registration Sensor Bracket |
| Парткод: | G070 2577 |
| Деталь: | Photo Reflection Sensor |
| Парткод: | AW01 0049 |
| Деталь: | Registration Sensor Harness |
| Парткод: | G070 5310 |
| Деталь: | Registration Guide |
| Парткод: | G070 2573 |
| Деталь: | Fly Wheel - 140mm |
| Парткод: | G070 4732 |
| Деталь: | Brushless Motor - DC8.8W 9Z |
| Парткод: | AX06 0224 |
| Деталь: | Drive Case - Assmbly |
| Парткод: | G070 4700 |
| Деталь: | Magnetic clutch |
| Парткод: | AX21 0078 |
| Деталь: | Brushless Motor - DC26W 9Z |
| Парткод: | AX06 0230 |
| Деталь: | Development Drive Bracket |
| Парткод: | G070 4611 |
| Деталь: | Idler Gear - 67Z |
| Парткод: | AB01 0353 |
| Деталь: | Gear - 93Z/42Z |
| Парткод: | AB01 7565 |
| Деталь: | Harness - Main Motor |
| Парткод: | B052 5417 |
| Деталь: | Harness - Development Motor |
| Парткод: | B052 5418 |
| Деталь: | Roller - Guide |
| Парткод: | A860 2560 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA082101 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 01 27 |
| Деталь: | Guide Plate - Paper Feed2 |
| Парткод: | B051 2568 |
| Деталь: | Roller - Vertical Transport |
| Парткод: | AF02 0558 |
| Деталь: | Upper Guide Plate - Paper Feed2 |
| Парткод: | B051 2553 |
| Деталь: | Guide Plate - Vertical Transport |
| Парткод: | B051 2610 |
| Деталь: | Cover - Vertical Transport |
| Парткод: | B051 2551 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0014 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | Compresion Spring |
| Парткод: | B051 2557 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | A232 2862 |
| Деталь: | Stopper Band |
| Парткод: | B051 2558 |
| Деталь: | Paper End Sensor Feeler |
| Парткод: | G070 2646 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 0866 |
| Деталь: | Release Lever |
| Парткод: | G070 2645 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Bracket - Paper End Sensor2 |
| Парткод: | B051 2550 |
| Деталь: | Feeler - Paper Bolume Sensor |
| Парткод: | G070 2647 |
| Деталь: | Sensor Rear Bracket |
| Парткод: | G070 2644 |
| Деталь: | Harness - Paper Feed2 |
| Парткод: | B052 5471 |
| Деталь: | Terminal Cover - Doctor Blade |
| Парткод: | G070 3293 |
| Деталь: | Doctor Blade Terminal |
| Парткод: | G070 3291 |
| Деталь: | Doctor Blade Terminal |
| Парткод: | G070 3292 |
| Деталь: | Rear Toner End Sensor |
| Парткод: | G070 5270 |
| Деталь: | Damper Cover |
| Парткод: | G070 3237 |
| Деталь: | Damper - Development Roller |
| Парткод: | G070 3248 |
| Деталь: | Rear Side Plate - Development |
| Парткод: | B051 3232 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | G070 3239 |
| Деталь: | Spring Cap |
| Парткод: | G070 3240 |
| Деталь: | Color Shaft - Development |
| Парткод: | G070 4605 |
| Деталь: | Doctor Blade Bias Harness |
| Парткод: | G070 5363 |
| Деталь: | Harness - ID Sensor Board |
| Парткод: | G070 5285 |
| Деталь: | Bias Terminal Cover |
| Парткод: | G070 3295 |
| Деталь: | Frontside Plate |
| Парткод: | G070 3231 |
| Деталь: | Development Vias Terminal |
| Парткод: | G070 3236 |
| Деталь: | ID Sensor Board |
| Парткод: | G070 5281 |
| Деталь: | High Boltage Harness - B2 |
| Парткод: | G070 5353 |
| Деталь: | Stay - Left Lower Assembly |
| Парткод: | B051 1106 |
| Деталь: | Front Toner End Sensor |
| Парткод: | G070 5260 |
| Деталь: | Side Plate - Front Left |
| Парткод: | G070 3233 |
| Деталь: | Display Decal - Magenta |
| Парткод: | G024 6992 |
| Деталь: | Display Decal - Cyan |
| Парткод: | G024 6991 |
| Деталь: | Display Decal - Yellow |
| Парткод: | G024 6993 |
| Деталь: | Display Decal - Black |
| Парткод: | G024 6994 |
| Деталь: | Front Lower Middle Shield |
| Парткод: | G070 1093 |
| Деталь: | Development Shaft - FC |
| Парткод: | G070 4607 |
| Деталь: | Development Unit - BK |
| Парткод: | B051 3204 |
| Деталь: | Development Unit - M |
| Парткод: | B051 3205 |
| Деталь: | Development Unit - Y |
| Парткод: | B051 3206 |
| Деталь: | Development Unit - C |
| Парткод: | B051 3207 |
| Деталь: | BUSHING |
| Парткод: | G024 1473 |
| Деталь: | Connector - By Pass |
| Парткод: | B052 5434 |
| Деталь: | Connector bracket |
| Парткод: | B051 5874 |
| Деталь: | Sensor bracket |
| Парткод: | G070 5542 |
| Деталь: | Temperature/humidity Sensor |
| Парткод: | AW14 0010 |
| Деталь: | Manual Feed Harness |
| Парткод: | B052 5430 |
| Деталь: | Stay - Lower Guide Plate |
| Парткод: | B051 5867 |
| Деталь: | Bracket - Power Supply Cord |
| Парткод: | B051 5866 |
| Деталь: | Stopper - PS Cord (120V) |
| Парткод: | B051 5675 |
| Деталь: | Stopper - PS Cord (230V) |
| Парткод: | B051 5677 |
| Деталь: | Roller Terminal - Oil Supply |
| Парткод: | G070 4314 |
| Деталь: | SPRING |
| Парткод: | AA06 3895 |
| Деталь: | Oil Supply Roller Holder |
| Парткод: | G070 4320 |
| Деталь: | Spring Plate - Oil Supply Roller |
| Парткод: | G070 4317 |
| Деталь: | Terminal Cover - Oil Supply Roller |
| Парткод: | G070 4316 |
| Деталь: | Roller Holder - Oil Supply |
| Парткод: | G070 4313 |
| Деталь: | Cable Plate |
| Парткод: | B051 5879 |
| Деталь: | AC Harness |
| Парткод: | B052 5423 |
| Деталь: | Connector bracket |
| Парткод: | G070 4310 |
| Деталь: | Harness - Power Supply Unit |
| Парткод: | B052 5414 |
| Деталь: | PSU Harness |
| Парткод: | B052 5465 |
| Деталь: | Power Supply Unit - 120V |
| Парткод: | AZ24 0074 |
| Деталь: | Power Supply Unit - 230V |
| Парткод: | AZ24 0076 |
| Деталь: | Fcc Cover |
| Парткод: | B051 1131 |
| Деталь: | Oil Tank Lower Bracket |
| Парткод: | B051 4353 |
| Деталь: | Bracket - Rear Lower Cover |
| Парткод: | B051 1331 |
| Деталь: | EXIOB Harness |
| Парткод: | B052 5441 |
| Деталь: | Upper Bracket - Contact Point |
| Парткод: | B051 5852 |
| Деталь: | Feeler - Paper Overflow |
| Парткод: | A267 4478 |
| Деталь: | Overflow Shaft |
| Парткод: | G070 4472 |
| Деталь: | Discharge Brush |
| Парткод: | AA120103 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Transport Exit Roller |
| Парткод: | AF02 0545 |
| Деталь: | Feeler - Paper Feed Sensor |
| Парткод: | A267 4476 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Exit Guide Plate |
| Парткод: | G070 4455 |
| Деталь: | Edit Grounding Plate |
| Парткод: | G070 4458 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1229 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0567 |
| Деталь: | Spring Plate - Outer Tension Roller |
| Парткод: | G070 4466 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0566 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | G070 4461 |
| Деталь: | Idle Roller |
| Парткод: | G047 4785 |
| Деталь: | Roller - 9mm |
| Парткод: | G070 4459 |
| Деталь: | Fusing Exit Roller |
| Парткод: | AF02 0546 |
| Деталь: | Guide Plate - Fusing Exit |
| Парткод: | G070 4481 |
| Деталь: | Bracket - Fusing Exit Feeler |
| Парткод: | G070 4477 |
| Деталь: | Spring - Fusing Exit Feeler |
| Парткод: | G070 4478 |
| Деталь: | Fusing Exit Feeler |
| Парткод: | G070 4476 |
| Деталь: | Fusing Exi Harness |
| Парткод: | B052 5403 |
| Деталь: | Sensor Bracket - Fusing Exit |
| Парткод: | G070 4486 |
| Деталь: | Discharge Brush |
| Парткод: | AA12 0113 |
| Деталь: | Grounding Plate - Fusing Exit |
| Парткод: | G070 4492 |
| Деталь: | Gear - 14Z |
| Парткод: | AB01 1230 |
| Деталь: | Exit Drive Bracket |
| Парткод: | G070 4920 |
| Деталь: | Gear - 27Z |
| Парткод: | AB01 1425 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 2112 |
| Деталь: | Photointerruptor - EE-SX4235A-P1 |
| Парткод: | AW02 0056 |
| Деталь: | Decal Warning (High Temperature) |
| Парткод: | AA00 0301 |
| Деталь: | Fusing Unit Assembly (120V) |
| Парткод: | B051 4025 |
| Деталь: | Fusing Unit Assembly (230V) |
| Парткод: | B051 4030 |
| Деталь: | Pick-off Pawl - Pressure Roller |
| Парткод: | G070 4004 |
| Деталь: | Knob Screw - 4m |
| Парткод: | B051 4103 |
| Деталь: | Oil Tank Packing |
| Парткод: | B051 4312 |
| Деталь: | Thermofuse - 131BC |
| Парткод: | G060 4351 |
| Деталь: | Decal - High Temperature Warning |
| Парткод: | AA00 0660 |
| Деталь: | Stripper Pawl - Pressure Roller |
| Парткод: | AE04 4041 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Front Cover - Fusing |
| Парткод: | B051 4108 |
| Деталь: | Shaft Support Plate |
| Парткод: | G070 4148 |
| Деталь: | Upper Cover - Fusing |
| Парткод: | B051 4101 |
| Деталь: | Guide Plate - Fusing Exit |
| Парткод: | G070 4106 |
| Деталь: | Fusing Belt Upper Stay |
| Парткод: | G070 4221 |
| Деталь: | Stripper Pawl Spring |
| Парткод: | AA06 9261 |
| Деталь: | Front Electrode Plate |
| Парткод: | G070 4132 |
| Деталь: | Rearelectrode Plate |
| Парткод: | G070 4135 |
| Деталь: | Connecting Electrode Plate |
| Парткод: | G070 4141 |
| Деталь: | Fusing Unit Harness |
| Парткод: | B051 5424 |
| Деталь: | Rear Pressure Terminal Electrode |
| Парткод: | G070 4143 |
| Деталь: | Fusing Lower Cover |
| Парткод: | G070 4130 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Absorben - Lower Fusing Cover |
| Парткод: | G070 4138 |
| Деталь: | Spring Plate - Front Fusing Cover |
| Парткод: | G070 4136 |
| Деталь: | Spring Plate - Rear Fusing Cover |
| Парткод: | G070 4137 |
| Деталь: | Fusing Sub Unit (120V) |
| Парткод: | B051 4026 |
| Деталь: | Fusing Sub Unit (230V) |
| Парткод: | B051 4031 |
| Деталь: | Discharge Harness |
| Парткод: | G070 5307 |
| Деталь: | Connector Holder |
| Парткод: | G070 2118 |
| Деталь: | Terminal Holder |
| Парткод: | G070 2126 |
| Деталь: | Charge Corona Terminal |
| Парткод: | G070 2124 |
| Деталь: | TERMINAL |
| Парткод: | G070 6165 |
| Деталь: | Terminal Holder |
| Парткод: | G070 6166 |
| Деталь: | PCU Grounding Plate |
| Парткод: | G070 2336 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Positioning Sensor - Transfer Belt |
| Парткод: | AW01 0096 |
| Деталь: | Positioning Sensor Bracket |
| Парткод: | G070 6160 |
| Деталь: | Positioning Sensor Plate |
| Парткод: | G070 6161 |
| Деталь: | Harness - Intermadediate Transfer |
| Парткод: | B052 5413 |
| Деталь: | Feeler |
| Парткод: | G070 2096 |
| Деталь: | SPRING |
| Парткод: | AA06 6633 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Waste Toner Bottle Bracket |
| Парткод: | G0702107 |
| Деталь: | Bracket - Waste Toner Sensor |
| Парткод: | G070 6407 |
| Деталь: | Paper End Sensor Feeler |
| Парткод: | G070 2646 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 0866 |
| Деталь: | Release Lever |
| Парткод: | G070 2645 |
| Деталь: | Feeler - Paper Bolume Sensor |
| Парткод: | G070 2647 |
| Деталь: | Paper End Sensor Bracket |
| Парткод: | G070 2642 |
| Деталь: | Sensor Rear Bracket |
| Парткод: | G070 2644 |
| Деталь: | Vertical Transport Feeler |
| Парткод: | G070 2638 |
| Деталь: | Paper Feed Harness |
| Парткод: | G070 5309 |
| Деталь: | EXIOB Harness |
| Парткод: | B052 5419 |
| Деталь: | PPI Harness |
| Парткод: | B051 5450 |
| Деталь: | High Boltage Harness - T2 |
| Парткод: | G070 5351 |
| Деталь: | Power Pack - BCTCLD (B051) |
| Парткод: | AZ32 0114 |
| Деталь: | Power Pack - BCTCLD (B052) |
| Парткод: | AZ32 0113 |
| Деталь: | Sensor Front Bracket |
| Парткод: | G070 2643 |
| Деталь: | Feeler Holder - Vertical Transport |
| Парткод: | G070 2637 |
| Деталь: | Connector Guide |
| Парткод: | G070 2143 |
| Деталь: | Charge Spring |
| Парткод: | G070 2138 |
| Деталь: | Seal - Plate |
| Парткод: | G070 2648 |
| Деталь: | Tube Bracket |
| Парткод: | B051 4357 |
| Деталь: | GRIP |
| Парткод: | G070 1051 |
| Деталь: | Rear Right Bracket - Grip |
| Парткод: | B051 1124 |
| Деталь: | Gear - 40Z/42Z |
| Парткод: | AB01 7560 |
| Деталь: | Magnetic clutch |
| Парткод: | AX20 0239 |
| Деталь: | Magnetic Clutch - 0.4nm 46z |
| Парткод: | AX20 0224 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Bracket - Magnetic Clutch1 |
| Парткод: | B051 4619 |
| Деталь: | Feed Drive Shaft |
| Парткод: | G070 4907 |
| Деталь: | Bracket - Magnetic Clutch2 |
| Парткод: | B051 4620 |
| Деталь: | Magnetic clutch |
| Парткод: | AX20 0240 |
| Деталь: | Rear Left Bracket - Grip |
| Парткод: | B051 1122 |
| Деталь: | Gear - 44Z/28Z |
| Парткод: | AB01 7601 |
| Деталь: | Transfer/separation Receptacle |
| Парткод: | G070 6223 |
| Деталь: | Timing Belt - 120TS2M |
| Парткод: | AA04 3567 |
| Деталь: | Gear - 33Z/30T |
| Парткод: | AB01 7561 |
| Деталь: | Paper Feed Tightener |
| Парткод: | G070 4908 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0869 |
| Деталь: | Stepper Motor - DC4.42W |
| Парткод: | G568 2702 |
| Деталь: | Cushion - Stepper Motor |
| Парткод: | AA16 1153 |
| Деталь: | GEAR COVER |
| Парткод: | B051 1086 |
| Деталь: | Bracket - Paper Feed Assembly |
| Парткод: | B051 4600 |
| Деталь: | Gear - 58Z/37Z |
| Парткод: | AB01 7563 |
| Деталь: | Pulley - 33T/32Z |
| Парткод: | AB01 7600 |
| Деталь: | Timing Belt - 480TS3M |
| Парткод: | AA04 3568 |
| Деталь: | Timing Belt - S3M103T |
| Парткод: | AA04 3941 |
| Деталь: | Photoconductor Conductor Unit |
| Парткод: | B051 2210 |
| Деталь: | Charge Corona Assembly |
| Парткод: | B051 2151 |
| Деталь: | Waste Toner Botle - OPC Belt |
| Парткод: | B051 2100 |
| Деталь: | Waste Toner Botle - Transfer Belt |
| Парткод: | B051 6310 |
| Деталь: | Flanged Hexagonal Head Bolt -M4x14 |
| Парткод: | G070 2358 |
| Деталь: | Cleaner Screw Shaft |
| Парткод: | G070 2165 |
| Деталь: | PCU Drive Joint |
| Парткод: | G070 2318 |
| Деталь: | Wire Cleaning Motor - DC0.46W |
| Парткод: | G070 2176 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 0087 |
| Деталь: | Spacer - 4x6x1 |
| Парткод: | A096 3863 |
| Деталь: | Charge Corona Wire |
| Парткод: | G070 2178 |
| Деталь: | Corona Wire Spring |
| Парткод: | 54 422 108 |
| Деталь: | Positioning Pin |
| Парткод: | A172 7611 |
| Деталь: | Charge Corona Grid |
| Парткод: | G070 2156 |
| Деталь: | SEAL |
| Парткод: | G070 2177 |
| Деталь: | Charge Corona Cleaner Holder |
| Парткод: | G070 2167 |
| Деталь: | FRONT POSITIONING PLATE |
| Парткод: | G070 2119 |
| Деталь: | Raer Positioning Plate |
| Парткод: | G070 2120 |
| Деталь: | DC Moter Cover - Charge Corona |
| Парткод: | G070 2173 |
| Деталь: | Grip Belt - PCU |
| Парткод: | G070 2344 |
| Деталь: | Doble Gear - 15Z/23Z |
| Парткод: | AB01 7595 |
| Деталь: | Rear Bracket - ITB Cleaning Unit |
| Парткод: | G070 6394 |
| Деталь: | Idler Gear - 20Z |
| Парткод: | AB01 4215 |
| Деталь: | Idler Gear - 19Z |
| Парткод: | AB01 4224 |
| Деталь: | Gear - 26Z |
| Парткод: | AB01 7631 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 1475 |
| Деталь: | Knob Screw - Charge Corona |
| Парткод: | G070 2174 |
| Деталь: | Grid Shadeing Plate |
| Парткод: | G070 2136 |
| Деталь: | Front End Block Cover |
| Парткод: | G070 2159 |
| Деталь: | Rear End Block Cover |
| Парткод: | G0702160 |
| Деталь: | Rear Bracket - Grid Plate |
| Парткод: | G070 2161 |
| Деталь: | Spring Plate - Gridtension |
| Парткод: | G070 2162 |
| Деталь: | Spring Plate - Screw Shaft |
| Парткод: | G070 2163 |
| Деталь: | Cleaner Slider - Charge Corona |
| Парткод: | G070 2166 |
| Деталь: | Charge Corona Cleaner |
| Парткод: | G070 2168 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1472 |
| Деталь: | Gear - 13Z |
| Парткод: | AB01 1473 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 1474 |
| Деталь: | Idler Gear - 35Z |
| Парткод: | AB01 1476 |
| Деталь: | Charge Section Assembly |
| Парткод: | G070 2050 |
| Деталь: | Belt Cleaning Assembly |
| Парткод: | G070 6300 |
| Деталь: | Cap - 20mm |
| Парткод: | A257 3490 |
| Деталь: | Spacer - Endblock |
| Парткод: | G070 2164 |
| Деталь: | Slider Ring |
| Парткод: | A172 7650 |
| Деталь: | Brushless Motor - DC26W 10Z |
| Парткод: | AX06 0225 |
| Деталь: | Bracket - Transport Assembly |
| Парткод: | B051 4800 |
| Деталь: | Transport Bracket |
| Парткод: | G070 4801 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Arm bracket |
| Парткод: | G070 4825 |
| Деталь: | Spring Clutch - 27Z |
| Парткод: | AB04 0020 |
| Деталь: | Gear - 33Z/27Z |
| Парткод: | G070 4850 |
| Деталь: | Swivel Bracket |
| Парткод: | G070 4810 |
| Деталь: | Gear - 25Z/36Z |
| Парткод: | G070 4851 |
| Деталь: | Gear - 30Z |
| Парткод: | AB01 4209 |
| Деталь: | Gear - 33Z |
| Парткод: | AB01 4210 |
| Деталь: | Second Drive Shaft |
| Парткод: | AA14 5544 |
| Деталь: | DC Solenoid - Transfer Roller |
| Парткод: | G070 4821 |
| Деталь: | Magnetic Clutch - 32Z |
| Парткод: | AX20 0236 |
| Деталь: | Cleaning Drive Shaft |
| Парткод: | AA14 5547 |
| Деталь: | Gear - 24Z/53Z |
| Парткод: | AB01 7556 |
| Деталь: | Grar - 65z/20z |
| Парткод: | AB01 7557 |
| Деталь: | Cleaning On/Off Shaft |
| Парткод: | AA14 5546 |
| Деталь: | Gear - 49Z |
| Парткод: | AB01 4208 |
| Деталь: | Second Shaft - On/Off |
| Парткод: | G070 4832 |
| Деталь: | Cam Roller |
| Парткод: | G070 4834 |
| Деталь: | SPRING SPACER |
| Парткод: | G070 4823 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3657 |
| Деталь: | Gear - 18Z |
| Парткод: | AB01 1479 |
| Деталь: | Cleaning On/off Cam |
| Парткод: | G070 4818 |
| Деталь: | DC Solenoid - Belt Cleaning |
| Парткод: | G070 4820 |
| Деталь: | Tension Spring - Arm |
| Парткод: | AA06 0884 |
| Деталь: | Timing Belt - 117TS2M |
| Парткод: | AA04 3566 |
| Деталь: | Timing Pulley - 24Z/34T |
| Парткод: | AB01 7555 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0868 |
| Деталь: | Tightener Assembly |
| Парткод: | G070 4741 |
| Деталь: | Gear - 98Z/20T |
| Парткод: | AB01 7554 |
| Деталь: | On/Off Cam |
| Парткод: | G070 4829 |
| Деталь: | Harness - Fusing Unit Motor |
| Парткод: | B052 5404 |
| Деталь: | GUIDE PLATE |
| Парткод: | G070 2606 |
| Деталь: | Guide Plate - Vertical Transport |
| Парткод: | G070 2607 |
| Деталь: | Leading Edghe Guide |
| Парткод: | G070 2608 |
| Деталь: | SCREW |
| Парткод: | AA14 3493 |
| Деталь: | Right Link - Transport Cover |
| Парткод: | G070 1196 |
| Деталь: | Front Support Plate - Right Cover |
| Парткод: | G070 1354 |
| Деталь: | SPRING HOLDER |
| Парткод: | A232 1284 |
| Деталь: | SPRING |
| Парткод: | AA06 3402 |
| Деталь: | Un Lock Hook |
| Парткод: | G070 1361 |
| Деталь: | Decal - Vertical Transport Grip |
| Парткод: | AA00 3020 |
| Деталь: | Light Lower Cover |
| Парткод: | G070 1284 |
| Деталь: | Rear Right Cover Hook |
| Парткод: | G070 1353 |
| Деталь: | Rear Support Plate - Right Cover |
| Парткод: | G070 1356 |
| Деталь: | RIGHT COVER |
| Парткод: | G070 1357 |
| Деталь: | Front Pulley Drive Wire |
| Парткод: | G570 1142 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Drive Wire - MM1.0 |
| Парткод: | AA05 0110 |
| Деталь: | Tension Bracket |
| Парткод: | G570 1136 |
| Деталь: | TENSION SPRING |
| Парткод: | A193 1783 |
| Деталь: | Pulley - Front Left |
| Парткод: | A267 1853 |
| Деталь: | Pulley - Rear Left |
| Парткод: | A267 1854 |
| Деталь: | Supporting Plate - Left Scanner |
| Парткод: | B051 1105 |
| Деталь: | Pulley - High Voltage Supply Cord |
| Парткод: | G570 2834 |
| Деталь: | 2nd Mirror Carriage - Assembly |
| Парткод: | G570 2820 |
| Деталь: | Xenon Lamp - 8.0MM |
| Парткод: | B051 1820 |
| Деталь: | Wire Clamp |
| Парткод: | A193 1766 |
| Деталь: | 1st Mirror Carriage - Assembly |
| Парткод: | G570 2720 |
| Деталь: | Clamp - Rear Wire |
| Парткод: | A193 1769 |
| Деталь: | Shielding Plate |
| Парткод: | G570 2733 |
| Деталь: | Timing Belt - S1.5M236 |
| Парткод: | AA04 3935 |
| Деталь: | Timing Pulley 73 |
| Парткод: | G570 1133 |
| Деталь: | Rear Pulley - Drive Wire |
| Парткод: | G570 1147 |
| Деталь: | Scanner Drive Shaft |
| Парткод: | G570 1132 |
| Деталь: | Stepper Motor - DC4.68W |
| Парткод: | G570 1150 |
| Деталь: | TENSION SPRING |
| Парткод: | A193 1784 |
| Деталь: | IOB Scanner Bracket |
| Парткод: | B051 1802 |
| Деталь: | Rear Right Bracket - Scanner |
| Парткод: | B051 1114 |
| Деталь: | Front Right Bracket - Scanner |
| Парткод: | B051 1113 |
| Деталь: | 2nd Slide Rail |
| Парткод: | G570 1030 |
| Деталь: | 1st Slide Rail |
| Парткод: | A193 1816 |
| Деталь: | Spacer Bushing |
| Парткод: | G570 1160 |
| Деталь: | Pulley Holder |
| Парткод: | G570 2833 |
| Деталь: | 2nd Mirror |
| Парткод: | G570 2826 |
| Деталь: | Spring Plate - 2nd Mirror |
| Парткод: | G404 2810 |
| Деталь: | Wire Pulley - M18 |
| Парткод: | A267 1855 |
| Деталь: | 1st Mirror |
| Парткод: | AC03 0142 |
| Деталь: | 1st Mirror Holder |
| Парткод: | A193 1767 |
| Деталь: | Heater - 9W (120V) |
| Парткод: | A250 1821 |
| Деталь: | Heater - 9W (230V) |
| Парткод: | A250 1822 |
| Деталь: | Guide - High Voltage Supply Cord |
| Парткод: | G570 2832 |
| Деталь: | Front door |
| Парткод: | G070 1250 |
| Деталь: | Cover - Main Switch |
| Парткод: | B051 1360 |
| Деталь: | Emblem - RIC(B051) |
| Парткод: | B051 7520 |
| Деталь: | Emblem - SAV(B051) |
| Парткод: | B051 7521 |
| Деталь: | Emblem - GES(B051) |
| Парткод: | B051 7522 |
| Деталь: | Emblem - NAS(B051) |
| Парткод: | B051 7523 |
| Деталь: | Emblem - REX(B051) |
| Парткод: | B051 7524 |
| Деталь: | Emblem - LAN(B051) |
| Парткод: | B051 7525 |
| Деталь: | Emblem - INF(B051) |
| Парткод: | B051 7526 |
| Деталь: | Emblem - RIC(B052) |
| Парткод: | B052 7520 |
| Деталь: | Emblem - SAV(B052) |
| Парткод: | B052 7521 |
| Деталь: | Emblem - GES(B052) |
| Парткод: | B052 7522 |
| Деталь: | Emblem - NAS(B052) |
| Парткод: | B052 7523 |
| Деталь: | Emblem - REX(B052) |
| Парткод: | B052 7524 |
| Деталь: | Emblem - LAN(B052) |
| Парткод: | B052 7525 |
| Деталь: | Emblem - INF(B052) |
| Парткод: | B052 7526 |
| Деталь: | Energy Decal |
| Парткод: | GA00 3035 |
| Деталь: | Hinge pin |
| Парткод: | A166 1363 |
| Деталь: | Magnet Catich - Front Cover |
| Парткод: | G070 1253 |
| Деталь: | Operate Sheet |
| Парткод: | B051 1392 |
| Деталь: | Decal - Inner Cover |
| Парткод: | A259 1522 |
| Деталь: | Inner Right Lower Cover |
| Парткод: | B051 1371 |
| Деталь: | Development Inner Cover |
| Парткод: | G070 1375 |
| Деталь: | Decal - Paper Tray |
| Парткод: | GA00 3014 |
| Деталь: | O/I Holder - Assembly |
| Парткод: | B027 8521 |
| Деталь: | LEFT INNER COVER |
| Парткод: | G070 1370 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0014 |
| Деталь: | LEFT COVER |
| Парткод: | B051 1280 |
| Деталь: | Stepped Screw - M6x1.7 |
| Парткод: | C105 2352 |
| Деталь: | Development Unit Cover |
| Парткод: | G070 1290 |
| Деталь: | REAR COVER |
| Парткод: | B051 1310 |
| Деталь: | Rivet - M7 |
| Парткод: | B039 1364 |
| Деталь: | Cover - Oil Tank |
| Парткод: | B051 1322 |
| Деталь: | Operating Instructions System - NA |
| Парткод: | B051 6507 |
| Деталь: | Operating Instructions System - AA |
| Парткод: | B051 6508 |
| Деталь: | Operating Instructions System - TWN |
| Парткод: | B051 6509 |
| Деталь: | DUST FILTER |
| Парткод: | A259 2337 |
| Деталь: | Rear Filter Cover - Development |
| Парткод: | B051 1317 |
| Деталь: | Dust Filter - Scanner |
| Парткод: | B051 1329 |
| Деталь: | Rear Small Cover - Filter |
| Парткод: | B051 1326 |
| Деталь: | Rear Cover - Cap |
| Парткод: | B051 1316 |
| Деталь: | Rear Filter Cover |
| Парткод: | B051 1320 |
| Деталь: | Sound Proofing - Cover Filter |
| Парткод: | G070 1077 |
| Деталь: | Seal - Filter Cover |
| Парткод: | B051 1324 |
| Деталь: | Seal - Filter Cover |
| Парткод: | B051 1328 |
| Деталь: | FILTER COVER |
| Парткод: | B051 1323 |
| Деталь: | Exhaust filter |
| Парткод: | AA01 2120 |
| Деталь: | OZONE FILTER |
| Парткод: | AA01 0113 |
| Деталь: | Rear Cover - Duplex |
| Парткод: | B051 1315 |
| Деталь: | Rear lower cover |
| Парткод: | B051 1311 |
| Деталь: | Lower Cover - Fan Motor |
| Парткод: | B051 1325 |
| Деталь: | RIGHT REAR COVER |
| Парткод: | B051 1270 |
| Деталь: | Gate Cap |
| Парткод: | B051 1271 |
| Деталь: | Duplex Small Cap |
| Парткод: | G0701262 |
| Деталь: | Rear Cap - Duplex |
| Парткод: | B051 1380 |
| Деталь: | Duplex Cap |
| Парткод: | G0701261 |
| Деталь: | Right front cover |
| Парткод: | B051 1260 |
| Деталь: | Operating Instructions Copy - NA |
| Парткод: | B051 6607 |
| Деталь: | Operating Instructions Copy - AA |
| Парткод: | B051 6608 |
| Деталь: | Operating Instructions Copy - TWN |
| Парткод: | B051 6609 |
| Деталь: | Operate Mask Decal |
| Парткод: | B051 1399 |
| Деталь: | Paper T ray Assembly |
| Парткод: | G070 2700 |
| Деталь: | Decal - Paper Set Direction |
| Парткод: | G070 2730 |
| Деталь: | Front Side Fence - Assembly |
| Парткод: | G070 2712 |
| Деталь: | Front Lever - Stopper |
| Парткод: | G070 2714 |
| Деталь: | Spring Plate Stopper |
| Парткод: | G070 2713 |
| Деталь: | Front Side Fence |
| Парткод: | AF01 6097 |
| Деталь: | END FENCE |
| Парткод: | AF01 7025 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | AF01 1047 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 52 152 713 |
| Деталь: | Spring - 5.9n/16.6n |
| Парткод: | AA06 3628 |
| Деталь: | Gear - 16Z |
| Парткод: | A267 2869 |
| Деталь: | Ground Plate- Bottom Plate |
| Парткод: | G070 2719 |
| Деталь: | Base Stopper |
| Парткод: | G070 2711 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 0866 |
| Деталь: | Rear Side Fence - Assembly |
| Парткод: | G070 2716 |
| Деталь: | Rear Lever - Stopper |
| Парткод: | G070 2717 |
| Деталь: | Rear Side Fence |
| Парткод: | AF01 6098 |
| Деталь: | Joint - Feed Roller Shaft |
| Парткод: | G070 2728 |
| Деталь: | SPRING |
| Парткод: | AA06 3630 |
| Деталь: | Bushing - 8x12x10 |
| Парткод: | B039 2727 |
| Деталь: | GROUNDING PLATE |
| Парткод: | G070 2725 |
| Деталь: | PAPER FEED ROLLER SHAFT |
| Парткод: | G070 2726 |
| Деталь: | Friction pad |
| Парткод: | G070 2722 |
| Деталь: | Spring - 2.8n |
| Парткод: | AA06 3629 |
| Деталь: | Paper Feed Roller - 36mm |
| Парткод: | AF03 1059 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Paper Size Sensor Link |
| Парткод: | G070 2710 |
| Деталь: | Decal - Paper Tray |
| Парткод: | AA00 3022 |
| Деталь: | Decal - OHP Paper Feed |
| Парткод: | B051 2580 |
| Деталь: | Decal - End Fence |
| Парткод: | B051 2581 |
| Деталь: | Scanner Front Frame |
| Парткод: | G570 1043 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 54 421 924 |
| Деталь: | Original Sensor - H81.5 |
| Парткод: | AW01 0095 |
| Деталь: | Stabilizer |
| Парткод: | B051 5730 |
| Деталь: | Sheet Through Bracket - DF |
| Парткод: | B051 1801 |
| Деталь: | Seal - Exposure Glass |
| Парткод: | B051 1803 |
| Деталь: | Lens Holder Assembly |
| Парткод: | B051 1689 |
| Деталь: | Bracket - Original Sensor |
| Парткод: | G570 1040 |
| Деталь: | Original Sensor - H2-66 |
| Парткод: | AW01 0056 |
| Деталь: | Interface Cable - BICU Board |
| Парткод: | B051 5331 |
| Деталь: | Scanner Home Sensor Stopper |
| Парткод: | A193 1793 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Inner cover |
| Парткод: | G570 1221 |
| Деталь: | Bracket - Document Feeder Hinge |
| Парткод: | B051 1800 |
| Деталь: | I/O Control Board - Scanner |
| Парткод: | B051 5232 |
| Деталь: | Scanner Harness |
| Парткод: | B052 5330 |
| Деталь: | Original Sensor - H1-66 |
| Парткод: | AW01 0059 |
| Деталь: | Laser Unit Assembly (B051) |
| Парткод: | B051 1858 |
| Деталь: | Laser Unit Assembly (B052) |
| Парткод: | B051 1856 |
| Деталь: | LD Unit Cover |
| Парткод: | G070 1971 |
| Деталь: | COVER |
| Парткод: | G070 1941 |
| Деталь: | Decal - LD 655 |
| Парткод: | AA00 0217 |
| Деталь: | Front Cover Shield |
| Парткод: | G070 1942 |
| Деталь: | Cylindrical Lens |
| Парткод: | G029 1975 |
| Деталь: | Sync Detector Holder |
| Парткод: | G070 1925 |
| Деталь: | Cover Bracket - LD Unit |
| Парткод: | G070 1972 |
| Деталь: | Sync Detector Board |
| Парткод: | G070 5240 |
| Деталь: | Harness - LD Control Board-sync |
| Парткод: | G070 5342 |
| Деталь: | BICU Harness |
| Парткод: | B052 5421 |
| Деталь: | FFC LD Harness |
| Парткод: | B051 5425 |
| Деталь: | Polygon Scanner |
| Парткод: | G070 1975 |
| Деталь: | CLEANER |
| Парткод: | G070 1955 |
| Деталь: | Cleaner Holder |
| Парткод: | G070 1954 |
| Деталь: | Shield Glass Cover |
| Парткод: | G070 1952 |
| Деталь: | Cleaner Shaft |
| Парткод: | G070 1953 |
| Деталь: | Positioning Pin |
| Парткод: | G070 1902 |
| Деталь: | Shield Glass |
| Парткод: | G070 1903 |
| Деталь: | Cleaner Grip |
| Парткод: | G070 1956 |
| Деталь: | Upper Cover - Right Front |
| Парткод: | B051 1205 |
| Деталь: | Paper Exit Cover - Sub Unit |
| Парткод: | B051 1300 |
| Деталь: | Front Cover - Scanner |
| Парткод: | B051 1345 |
| Деталь: | Caution Chart Decal - English |
| Парткод: | B051 1347 |
| Деталь: | Cover - Right Exit |
| Парткод: | B051 1251 |
| Деталь: | Cover - Upper Exit |
| Парткод: | B051 1252 |
| Деталь: | Decal - Exit Grip |
| Парткод: | AA00 3021 |
| Деталь: | Left Cover - Paper Exit |
| Парткод: | B051 1250 |
| Деталь: | Exit Connecting Cover - Cap |
| Парткод: | B051 1255 |
| Деталь: | Cover - Rear Exit |
| Парткод: | B051 1253 |
| Деталь: | Rear Exit Cover - Cap |
| Парткод: | B051 1254 |
| Деталь: | LEFT UPPER COVER |
| Парткод: | B051 1290 |
| Деталь: | Left Cover - Scanner |
| Парткод: | B051 1341 |
| Деталь: | STEPPED SCREW |
| Парткод: | A193 1759 |
| Деталь: | Left Scale - Printing |
| Парткод: | B024 1700 |
| Деталь: | Left Scale Guide |
| Парткод: | A193 1752 |
| Деталь: | Left Scale |
| Парткод: | B024 1680 |
| Деталь: | Exposure Glass |
| Парткод: | A250 1752 |
| Деталь: | Inner Back Scale |
| Парткод: | B024 1701 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0014 |
| Деталь: | Rear Cover - Scanner |
| Парткод: | B051 1340 |
| Деталь: | Light Cover - Scanner |
| Парткод: | B051 1342 |
| Деталь: | Operation Panel Sub Unit (NA) |
| Парткод: | B051 1455 |
| Деталь: | Operation Panel Sub Unit (EU) |
| Парткод: | B051 1456 |
| Деталь: | Operation Panel Sub Unit (TWN) |
| Парткод: | B051 1457 |
| Деталь: | Operation Panel Sub Unit (AA) |
| Парткод: | B051 1458 |
| Деталь: | Operation Panel Board - Right |
| Парткод: | G570 1991 |
| Деталь: | Sheet Power Source (120V) |
| Парткод: | G570 2068 |
| Деталь: | Sheet Power Source (230V) |
| Парткод: | G570 2078 |
| Деталь: | Keytop Cover - Right |
| Парткод: | G570 1971 |
| Деталь: | Sheet - Color C |
| Парткод: | G570 1966 |
| Деталь: | Sheet LED - English |
| Парткод: | G570 2080 |
| Деталь: | Keytop Switch - Large |
| Парткод: | G570 1963 |
| Деталь: | Lens - Data Input |
| Парткод: | G570 1972 |
| Деталь: | Keytop - Color Adjust |
| Парткод: | G570 1948 |
| Деталь: | Keytop - Counter |
| Парткод: | G5701951 |
| Деталь: | Keytop - ACS |
| Парткод: | B051 1482 |
| Деталь: | Keytop - Color Select |
| Парткод: | G5701953 |
| Деталь: | Knob - Contrast |
| Парткод: | G5701964 |
| Деталь: | Operation Panel Board - Left |
| Парткод: | G5701990 |
| Деталь: | LCDC Board (120V) |
| Парткод: | B051 5236 |
| Деталь: | LCDC Board (230V) |
| Парткод: | B051 5237 |
| Деталь: | LCDC Board (TWN/AA) |
| Парткод: | B051 5231 |
| Деталь: | LCDC Cover |
| Парткод: | B004 1521 |
| Деталь: | Bracket - Operation Panel LCD |
| Парткод: | G570 1980 |
| Деталь: | LCD - Hvga U14 B1 |
| Парткод: | B004 5216 |
| Деталь: | TOUCH PANEL |
| Парткод: | A229 5216 |
| Деталь: | Keytop - Check Modes |
| Парткод: | G570 1947 |
| Деталь: | Keytop - Program |
| Парткод: | G5701950 |
| Деталь: | Keytop Clear Modes - EXP |
| Парткод: | G570 2062 |
| Деталь: | Keytop - Energy Saver |
| Парткод: | G5701946 |
| Деталь: | Keytop - Interrupt |
| Парткод: | G5701945 |
| Деталь: | Keytop - Power Source |
| Парткод: | G5701967 |
| Деталь: | Keytop - Sample Copy |
| Парткод: | G570 1943 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | G570 1942 |
| Деталь: | Keytop - 10key (120V) |
| Парткод: | G570 2061 |
| Деталь: | Keytop - 10key (230V) |
| Парткод: | G570 1944 |
| Деталь: | Keytop - 10key (AA) |
| Парткод: | B051 1491 |
| Деталь: | Keytop - Start/Stop |
| Парткод: | G570 1941 |
| Деталь: | Keytop - Switch (120 V) |
| Парткод: | G570 2064 |
| Деталь: | Keytop - Switch (230V) |
| Парткод: | G570 2074 |
| Деталь: | Keytop Copy (120 V) |
| Парткод: | G570 2063 |
| Деталь: | Keytop Copy (230V) |
| Парткод: | G570 2073 |
| Деталь: | Case - Operation Panel(120V) |
| Парткод: | B051 1485 |
| Деталь: | Case - Operation Panel (230V) |
| Парткод: | G570 2051 |
| Деталь: | Paper T ray2 Assembly |
| Парткод: | B051 2700 |
| Деталь: | Decal - Paper Set Direction |
| Парткод: | G070 2730 |
| Деталь: | Front Side Fence - Assembly |
| Парткод: | G070 2712 |
| Деталь: | Front Lever - Stopper |
| Парткод: | G070 2714 |
| Деталь: | Spring Plate Stopper |
| Парткод: | G070 2713 |
| Деталь: | Front Side Fence |
| Парткод: | AF01 6097 |
| Деталь: | END FENCE |
| Парткод: | AF01 7025 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | AF01 1047 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 52 152 713 |
| Деталь: | Spring - 5.9n/16.6n |
| Парткод: | AA06 3628 |
| Деталь: | Gear - 16Z |
| Парткод: | A267 2869 |
| Деталь: | Ground Plate- Bottom Plate |
| Парткод: | G070 2719 |
| Деталь: | Base Stopper |
| Парткод: | G070 2711 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 0866 |
| Деталь: | Rear Side Fence - Assembly |
| Парткод: | G070 2716 |
| Деталь: | Rear Lever - Stopper |
| Парткод: | G070 2717 |
| Деталь: | Rear Side Fence |
| Парткод: | AF01 6098 |
| Деталь: | Joint - Feed Roller Shaft |
| Парткод: | G070 2728 |
| Деталь: | SPRING |
| Парткод: | AA06 3630 |
| Деталь: | Bushing - 8x12x10 |
| Парткод: | B039 2727 |
| Деталь: | GROUNDING PLATE |
| Парткод: | G070 2725 |
| Деталь: | PAPER FEED ROLLER SHAFT |
| Парткод: | G070 2726 |
| Деталь: | Friction pad |
| Парткод: | G070 2722 |
| Деталь: | Spring - 2.8n |
| Парткод: | AA06 3629 |
| Деталь: | Paper Feed Roller - 36mm |
| Парткод: | AF03 1059 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Paper Size Sensor Link |
| Парткод: | G070 2710 |
| Деталь: | Decal - Paper Tray |
| Парткод: | AA00 3022 |
| Деталь: | Decal - OHP Paper Feed |
| Парткод: | B051 2580 |
| Деталь: | Decal - End Fence |
| Парткод: | B051 2581 |
| Деталь: | Rubber Foot - 23mm |
| Парткод: | G024 1007 |
| Деталь: | Lower Shield - Front Left |
| Парткод: | G070 1094 |
| Деталь: | Arm - Scanner |
| Парткод: | B051 1104 |
| Деталь: | Lower Shield - PCU Rail |
| Парткод: | G070 1092 |
| Деталь: | PCU Lower Rail |
| Парткод: | G070 2372 |
| Деталь: | Upper Supporting Stay |
| Парткод: | B051 2368 |
| Деталь: | PCU Rail Seal - 9x19x5 |
| Парткод: | G070 1105 |
| Деталь: | PCU Rail Seal - 3x30x5 |
| Парткод: | G070 1104 |
| Деталь: | PCU Upper Rail |
| Парткод: | G070 2371 |
| Деталь: | DENSITY SENSOR |
| Парткод: | AW01 0097 |
| Деталь: | On/off Rail |
| Парткод: | G070 6405 |
| Деталь: | Grounding Plate - Belt Cleaning |
| Парткод: | G070 6406 |
| Деталь: | Frame - Right Front Upper |
| Парткод: | B051 1076 |
| Деталь: | Stay - Right Upper Assembly |
| Парткод: | B051 1102 |
| Деталь: | Light Midle Stay |
| Парткод: | B051 1101 |
| Деталь: | Fusing Unit Rail |
| Парткод: | G070 4302 |
| Деталь: | Rail - Fusing |
| Парткод: | B051 4298 |
| Деталь: | Right Rail Shoe |
| Парткод: | G070 2622 |
| Деталь: | Right Rail |
| Парткод: | G070 2620 |
| Деталь: | Grounding Plate Bracket |
| Парткод: | G070 6227 |
| Деталь: | Charge Ground Plate |
| Парткод: | G070 2135 |
| Деталь: | Rear Left Frame - Lengthwise |
| Парткод: | B051 1091 |
| Деталь: | Rear Upper Frame |
| Парткод: | B051 1093 |
| Деталь: | Connector Gate Bracket |
| Парткод: | B051 1126 |
| Деталь: | Rear Right Frame - Lengthwise |
| Парткод: | B051 1092 |
| Деталь: | Right Cover - Vertical Transport |
| Парткод: | B051 1359 |
| Деталь: | Transfer Unit Stopper |
| Парткод: | G070 6221 |
| Деталь: | SPRING |
| Парткод: | AA06 3563 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | A232 2862 |
| Деталь: | Transfer Unit Spring -10n |
| Парткод: | AA06 3876 |
| Деталь: | Registration Driven Cleaner |
| Парткод: | G070 2585 |
| Деталь: | Right Cover Guide - By-pass Feed |
| Парткод: | G070 1281 |
| Деталь: | Spring - 20n |
| Парткод: | AA06 3631 |
| Деталь: | BUSHING |
| Парткод: | AA08 0259 |
| Деталь: | Vertical Transport Sheet |
| Парткод: | G070 6229 |
| Деталь: | Registration Driven Roller - 14mm |
| Парткод: | AF02 1068 |
| Деталь: | Right Guide Plate |
| Парткод: | G070 2583 |
| Деталь: | GROUNDING PLATE |
| Парткод: | G070 2584 |
| Деталь: | Entrance Guide |
| Парткод: | G070 6245 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | G070 6200 |
| Деталь: | Roller - Transfer Roller |
| Парткод: | G070 6201 |
| Деталь: | Collar - 8x11x10 |
| Парткод: | G070 6236 |
| Деталь: | Transfer Roller Bushing |
| Парткод: | G070 6202 |
| Деталь: | Transfer Roller Holder |
| Парткод: | G070 6206 |
| Деталь: | Transport Guide W/t Discharge Pins |
| Парткод: | G070 6231 |
| Деталь: | Separation Bias Wire |
| Парткод: | G070 5356 |
| Деталь: | Rear Arm |
| Парткод: | G070 6239 |
| Деталь: | Transfer Unit Frame |
| Парткод: | G070 6204 |
| Деталь: | Arm Shaft |
| Парткод: | G070 6240 |
| Деталь: | Ground Wire - 2nd Transfer Arm |
| Парткод: | G070 5370 |
| Деталь: | Rear Grounding Plate |
| Парткод: | G070 6210 |
| Деталь: | Transfer Roller Terminal |
| Парткод: | G070 6218 |
| Деталь: | Terminal Cover Sheet |
| Парткод: | B051 6243 |
| Деталь: | Frame Stay |
| Парткод: | G070 6205 |
| Деталь: | Front Arm |
| Парткод: | G070 6238 |
| Деталь: | Separation Terminal |
| Парткод: | G070 6220 |
Коды ошибок
101
120
121
122
142
161
195
201
220
221
230
231
241
280
282
300
301
302
305
350
351
352
400
401
410
411
412
420
421
430
440
460
461
480
481
503
504
515
520
521
541
542
543
544
545
546
551
552
553
554
555
556
560
570
571
620
630
632
633
634
635
640
641
670
672
685
687
720
722
724
725
726
727
728
730
731
732
740
750
770
791
792
793
800
801
802
803
804
805
806
807
808
809
810
818
819
820
821
822
823
824
826
827
828
829
835
836
837
838
850
851
853
854
855
856
860
861
862
863
864
865
870
900
901
902
925
990
991
992
997
998
999
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 122 |
| Display: | Service Call 122: Error |
| Description: | Finisher Decurler Failure, Code 122 The level of the Decurler Cam Home Sensor did not change 4 seconds after the Decurler Cam Clutch has turned on. |
| Causes: | • Decurler Cam Clutch • Stacker Motor • Finisher Control Board |
| Remedy: | 1 1. Rotate the actuator while running the Decurler Cam Position test in diagnostics. 2. Does the value change between H and L? Go to step 2. Troubleshoot using the transmissive sensor procedure. 2 Does the decurler cam clutch operate in diagnostics? Check for a mechanical problem with the decurler cam clutch drive. If no problem is found replace the clutch. Go to step 3. 3 Is +24 VDC present at P/J 849-1? Replace the decurler cam clutch. Go to step 4. 4 Is +24 VDC present at test point 5 on the finisher control board? Replace the finisher control board. Troubleshoot the +24 VDC interlock circuit. 5 Is +24 VDC present at P/J 847-11 with the Finisher Stacker Motor Down test running in diagnostics? Replace the stacker motor. Replace the finisher control board |
| Error code: | 142 |
| Display: | Contact the Service center. 142: Error |
| Description: | Motor |
| Causes: | • Standard white plate defective, dirty • Moisture inside the scanner unit • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor, over speed - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”. |
| Error code: | 161 |
| Display: | SYSTEM HALT (*) 161 : PCB MAIN-F6 |
| Description: | IPU Error At power on, or when the machine returns from an energy save mode, the self-diagnostic program returned an IPU error. |
| Causes: | • IPU defective • Connection between SBU and IPU is loose, broken, or defective |
| Error code: | 195 |
| Description: | Serial Number Error |
| Causes: | The serial number stored in the memory (EGB) is not correct. |
| Remedy: | EEPROM defective EGB replaced without original EEPROM |
| Error code: | 201 |
| Display: | ERROR 201 COMMAND |
| Description: | PU F/W Flash write error (Reserved) |
| Causes: | • Defective polygon motor • Defective harness |
| Remedy: | 1. Connect the cable correctly. 2. Replace the engine control board. 3. Replace the laser scanning unit. 4. Check or replace the cable. |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 221 |
| Description: | Laser synchronizing detection error: start position [K]: LD1 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 231 |
| Display: | Service Call 231: Error |
| Description: | FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 241 |
| Display: | Service call 241:Error |
| Description: | LD error: Y The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 280 |
| Description: | Paper Jam Clear Paper Path Leave sheets in Finisher area 5 |
| Causes: | • Defective BCU • Poor electrical connection • Noise |
| Remedy: | Primary: Media has jammed in the Finisher Option. Open the finisher option front door to access the jammed pages. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “280 Paper Jam” on page 2-82. |
| Error code: | 282 |
| Description: | Staple Jam Check Stapler Remove Job from Finisher |
| Causes: | • Defective BCU |
| Remedy: | The stapler device detects a paper jam during normal stapler operation such as when printing and stapling jobs. Check stapler are for jam in accumulator or stapler. Remove stapler cartridge to check for staple jam. Note: After the error has been cleared, the printer does not reprint any pages which existed in the accumulator for stapling. The following actions can be taken while either the primary or secondary messages are displayed: Press Go to initiate priming and resume printing. |
| Error code: | 300 |
| Description: | High voltage power output error |
| Causes: | The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit). |
| Remedy: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB. |
| Error code: | 301 |
| Description: | Fuser web must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 305 |
| Display: | ERROR 305 USB TIME OUT |
| Description: | Charge Corona Wire Cleaner Error The charge wire cleaner did not: (1) come from the home position within 5 s, or (2) did return to the home position within 3.75 s due to wire cleaner overload. |
| Causes: | • Cleaner unit blocked or damaged • Until replacement parts become available, set SP2804 to "0" to disable the charge-corona cleaning function so the machine can operate. |
| Error code: | 350 |
| Description: | ID sensor error 1 One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. Vsp greater than or equals 2.5V Vsg less than 2.5 Vsp = 0V Vsg = 0 |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 351 |
| Description: | ID sensor error 2 The ID sensor output voltage is 5.0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 352 |
| Description: | ID sensor error 3 For 2 s during the ID sensor pattern check, the ID sensor pattern edge voltage is not 2.5V or the pattern edge is not detected within 800 ms. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 400 |
| Display: | Open top cover 400: Paper size error |
| Description: | TM sensor error |
| Causes: | The CPU detected a low voltage of the positive reflection output under the threshold in the TM sensor. |
| Remedy: | • TM sensors are dirty. • A solid print out due to an electrostatic charging error • The TM sensor is defective. 1. Clean the TM sensors. 2. Replace the TM sensors. 3. Check the image transfer unit. 4. Turn the power Off and On. |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 410 |
| Description: | ID sensor error: Development K. D evelopment gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | 1. Replace the ID/ MUSIC sensors. 2. Check the harness connection to the LD unit. 3. Replace the LD unit. 4. Check the harness connection to the CGB HVPS. 5. Replace the CGB HVPS. 6. Replace the developer. |
| Error code: | 411 |
| Display: | SVC 411 ERROR |
| Description: | IRQ timer 1 error |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | Replace the Controller board. |
| Error code: | 412 |
| Display: | SVC 412 ERROR |
| Description: | IRQ timer 2 error |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | Replace the Controller board. |
| Error code: | 420 |
| Display: | ERROR 420 Z POSITION |
| Description: | Potential sensor error: Vd Adjustment K. The drum potential sensor detects 150V or more on the drum (Vd) for 0.7 msec. when the high voltage charge is supplied to the drum for the initial sampling before exposure. |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Drum worn |
| Remedy: | 1. Clean or replace the drum potential sensor. 2. Replace the drum unit. |
| Error code: | 421 |
| Display: | ERROR 421 !CHECK FILTER |
| Description: | Potential sensor error: Vd Adjustment C. The drum potential sensor detects 150V or more on the drum (Vd) for 0.7 msec. when the high voltage charge is supplied to the drum for the initial sampling before exposure. |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Drum worn |
| Remedy: | 1. Clean or replace the drum potential sensor. 2. Replace the drum unit. |
| Error code: | 430 |
| Description: | Quenching lamp error At the completion of auto process control initialization, the potential of the drum surface detected by the potential sensor is more than -400V, the prescribed value. |
| Causes: | • Quenching lamp defective • Quenching lamp harness disconnected • Quenching lamp connector loose, defective |
| Error code: | 440 |
| Description: | Transfer Output Error. A high voltage feedback voltage of less than 0.5 V was detected for 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 460 |
| Description: | DC Separation Corona Output Error A dc separation feedback voltage of less than 0.5 V was detected after more than 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 461 |
| Description: | Humidity sensor error The output is 4.5 V (or higher) or 0.3 V (or lower) for 12 seconds. |
| Causes: | • Short circuit in the humidity sensor • Defective circuit • Defective connector |
| Error code: | 480 |
| Display: | Remove paper 480: Stacker full |
| Description: | Agitator Motor Error |
| Causes: | The agitator motor error is detected twice for 10 msec during the initialization at power-on or after the cover is closed. |
| Remedy: | • Disconnected or defective harness • Defective agitator motor 1. Check or replace the harness. 2. Replace the agitator motor. |
| Error code: | 481 |
| Description: | OPC belt sensor error |
| Causes: | • Defective OPC belt unit • Dirty OPC belt • Loose connection • Defective OPC belt sensor • Defective input output device • Defective BCU |
| Error code: | 503 |
| Display: | Service Call 503: Error |
| Description: | Tray 3 must be rebuilt |
| Causes: | (A model other than D581) Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. (D581) Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 504 |
| Description: | Tray 4 must be rebuilt |
| Causes: | The 2nd tray of D580, 1st tray of D580 when D579 and D580 are attached, the bottom D579 when two units of D579 are attached, or D631 when D581 and D631 are attached. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection D581 when D579 and D581 are attached.Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 515 |
| Display: | ERROR 515 DETECTION ERROR |
| Description: | DADF belt should be replaced |
| Causes: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors • Paper or other obstacle trapped between tray and motor • Motor mechanical overload due to obstruction • Return sensor or HP sensor defective or dirty Note • This problem will not issue the SC code on the operation panel. • The machine will prompt the operator to reset tray by opening and closing it. • If the problem persists, the machine will display again and the tray cannot be used. |
| Error code: | 520 |
| Description: | Replace optics filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 521 |
| Description: | Replace particle filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 554 |
| Description: | Fusing sleeve belt overheat: End (hardware error) The fusing sleeve belt thermistor detects 250°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 555 |
| Description: | Fusing Heater error: End The fusing heater keeps full power for 9 seconds or more. |
| Causes: | Defective thermistors. Broken heater cables. |
| Error code: | 556 |
| Description: | Unstable fusing temperature (rear) The fusing temperature varies 50° C or more within 1 second, and this occurs 2 consecutive times. |
| Causes: | • Thermistor defective or out of position • Power supply unit defective |
| Error code: | 560 |
| Description: | Zero cross error The main switch is turned on; the fusing relay turns on. - 50 Hz or 60 Hz is not detected within 5 seconds. |
| Causes: | • Defective relay circuit • Defective PSU • Incorrect power supply |
| Error code: | 570 |
| Description: | Charge bias leak High voltage unit sends a signal of charge bias leak. |
| Causes: | • Defective charge roller • Defective high voltage unit |
| Error code: | 571 |
| Description: | Pressure roller thermistor error: Center The center temperature of the pressure roller measured by the thermistor does not reach 0°C for 8 seconds. |
| Causes: | Defective thermopile. Defective thermistor. Loose connection. |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 630 |
| Description: | CSS communication error A communication error occurred during communication with the CSS. |
| Causes: | • Communication line error |
| Remedy: | Logging only. |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 633 |
| Description: | Key/card counter device error 2 During communication with the device, the MCU received a break (Low) signal. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 640 |
| Description: | Communication error: Engine Controller (Check sum error) Sum value is added each command frame. Sum check means: STX xx xx xx xx sum ETX -> The least significant 7 bits of xx + xx + xx+ xx is compared with the sum Example: STX 80h 81h 82h 83h 06h ETX -> 80h + 81h + 82h + 83h = 206h If sum value is 06h, data is correct. This SC is not displayed when it occurs; count is executed only by logging. |
| Causes: | Hard error with PCI |
| Remedy: | 1. Turn the main switch off and on. |
| Error code: | 641 |
| Description: | BICU control data transfer abnormal A sampling of the control data sent from the BICU reveals an abnormality. |
| Causes: | • Defective controller board • External noise • Defective BCU |
| Remedy: | 1. Replace the controller board. 2. Replace the BCU. |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 685 |
| Description: | SBU/IPU communication error While data is sent between the scanner and BICU board, a communication error has occurred. |
| Causes: | • Defective scanner unit cable • Defective SBU board • Defective BICU board |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720 |
| Description: | Fan folder transport motor error A transport motor lock signal was detected for more than 5 sec. while the motor was running. |
| Causes: | • Transport motor harness connector loose, disconnected, broken • Motor overload due to an obstruction • Transport motor defective • Fan folder unit MCU defective |
| Error code: | 722 |
| Description: | Finisher jogger motor error The finisher jogger HP sensor did not return to the home position, or move out of the home position, within 1.25 sec. Staple mode cannot be used. |
| Causes: | • Jogger motor connector or harness loose, broken, defective • Jogger motor defective • Jogger HP sensor connector or harness loose, broken, defective • Jogger HP sensor defective |
| Error code: | 724 |
| Description: | Finisher staple hammer motor error Stapling does not finish within 150 ms after the staple hammer motor turned on. Staple mode cannot be used. |
| Causes: | • Staple jam • Stapler overload caused by trying to staple too many sheets • Staple hammer motor connector or harness loose, broken, defective • Staple hammer motor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the staple hammer motor HP sensor if the motor is rotating. 4. Replace the finisher main board. |
| Error code: | 725 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor. 4. Replace the finisher main board. |
| Error code: | 726 |
| Description: | Front shift jogger motor error (B703) The sides fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift jogger motor disconnected, defective • Shift jogger motor overloaded due to obstruction • Shift jogger HP sensor disconnected, defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift jogger HP sensor 4. Replace the shift jogger motor. 5. Replace the finisher main board. |
| Error code: | 727 |
| Description: | Rear shift jogger motor (B703) The side fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code |
| Causes: | Motor harness disconnected, loose, defective Motor defective Motor overload HP defective boar |
| Error code: | 728 |
| Description: | Shift jogger retraction motor error (B703) The side fences do not retract within the prescribed time after the retraction motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray jogger lift HP sensor. 4. Replace the shift jogger retraction motor. 5. Replace the finisher main board. |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 731 |
| Description: | Finisher exit guide motor error After the finisher exit guide motor turned on, the exit guide sensor did not activate within 800 ms. |
| Causes: | • Finisher exit guide motor defective harness or connector loose, broken, defective • Finisher exit guide motor defective • Finisher exit guide sensor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the upper tray exit motor. 4. Replace the finisher main board. |
| Error code: | 732 |
| Description: | Finisher shift roller motor error The shift roller HP sensor does not activate within the prescribed time after the shift roller motor turns on. After 2 counts, the SC is logged as a jam. |
| Causes: | • Shift roller HP sensor defective • Sensor harness disconnected, defective • Shift roller motor defective • Finisher main board defective • Shift roller motor overload |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray exit motor. 4. Replace the finisher main board. |
| Error code: | 740 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished after a certain time. For the 1000-sheet booklet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 750 |
| Description: | 1000/3000-sheet (booklet) finisher: Tray lift motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. |
| Causes: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor |
| Remedy: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor. |
| Error code: | 770 |
| Description: | Shift motor error The shift motor HP sensor does not detect any change for 1.86 seconds after the shift motor has turned on at power on or during its operation. |
| Causes: | Defective shift motor. Defective shift motor HP sensors. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 791 |
| Description: | Bridge unit error The machine recognizes the finisher, but does not recognize the bridge unit. |
| Causes: | The bridge unit is not installed. Defective bridge unit. Re-install the bridge unit. Turn the main power switch off and on. |
| Remedy: | • Re-install the bridge unit. • Turn the main power switch off and on. |
| Error code: | 792 |
| Description: | Finisher error The machine does not recognize the finisher, but recognizes the bridge unit. |
| Causes: | The finisher`s connection is faulty. The finisher is not attached to a device equipped with the bridge unit. Defective finisher. |
| Remedy: | Reconnect the finisher or bridge unit, and then turn the main power switch off and then back on. |
| Error code: | 793 |
| Description: | Finisher gathering roller motor error |
| Causes: | • Motor overload • Loose connection of the gathering roller motor • Defective gathering roller motor |
| Remedy: | • Check the connections to the gathering roller motor. • Replace the gathering roller motor. |
| Error code: | 800 |
| Description: | Startup without video output end error (K) Video transfer to the engine is started, but the engine did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Error code: | 801 |
| Display: | SYSTEM HALT (*) 801 : (C)OPCODE |
| Description: | Video output error (Y) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 802 |
| Display: | SYSTEM HALT (*) 802 : (C)SLOT |
| Description: | Video output error (M) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 803 |
| Display: | SYSTEM HALT (*) 803 : (C)CPU ADDR |
| Description: | Video output error (C) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 804 |
| Display: | SYSTEM HALT (*) 804 : (C)DMA ADDR |
| Description: | Startup without video input end (K) A video transmission was requested from the scanner, but the scanner did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 805 |
| Display: | SYSTEM HALT (*) 805 : (C)ZERO DIV |
| Description: | Startup without video input end error (Y) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 806 |
| Display: | SYSTEM HALT (*) 806 : FW/SIO bit |
| Description: | Startup without video input end error (M) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 807 |
| Display: | SYSTEM HALT (*) 807 : FW/SIO wbsy |
| Description: | Startup without video input end error (C) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 808 |
| Display: | SYSTEM HALT (*) 808 : FW/STP-MTR |
| Description: | Startup without video input end error (R) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 809 |
| Display: | SYSTEM HALT (*) 809 : FW/XY param |
| Description: | Startup without video input end error (G) Video transfer to the engine is started, but a video transmission end command is not issued by the engine within the specified time. |
| Causes: | • Defective controller board |
| Error code: | 810 |
| Display: | SYSTEM HALT (*) 810 : FW/KEY RDI |
| Description: | Startup without video input end error (B) Video transfer to the engine is started, but a video transmission end command is not issued by the engine within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 835 |
| Display: | SYSTEM HALT (*) 835 : FW/PRN MDL |
| Description: | Self-diagnostic error: Centronic device |
| Causes: | [1102] Loopback connector is connected but check results in an error. • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [110C] Loopback connector is connected but check results in an error. • ASIC device error • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [1120] Centronic loopback connector is not connected for detailed self-diagnostic test. • Centronic loopback connector not connected correctly • Centronic loopback connector defective • ASIC device defective Replace the controller board. |
| Error code: | 836 |
| Display: | SYSTEM HALT (*) 836 : FW/SV MDL |
| Description: | Self-diagnostics error: Font ROM (standard) |
| Causes: | Turn the main switch off and on. Replace the standard ROM-DIMM. |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the controller board. |
| Error code: | 837 |
| Display: | SYSTEM HALT (*) 837 : FW/PRN MDL |
| Description: | Self-diagnostic error - Optional font ROM The data in the font ROM (optional ROM-DIMM) is damaged. |
| Causes: | • Defective optional ROM-DIMM. |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the optional ROM-DIMM. |
| Error code: | 838 |
| Display: | SYSTEM HALT (*) 838 : FW/SV MDL |
| Description: | Self-diagnostic Error 10: Clock Generator A verify error occurred when setting data was read from the clock generator via the I2C bus. |
| Causes: | • Replace the controller board |
| Error code: | 850 |
| Description: | Net I/F error Duplicate IP addresses. Illegal IP address. Driver unstable and cannot be used on the network |
| Causes: | • IP address setting incorrect • NIB (PHY) board defective • Controller board defective |
| Remedy: | Turn the main switch off and on. |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 862 |
| Description: | Bad sector number error The number of bad sectors in the HDD (image data area) goes over 101. |
| Causes: | • Defective HDD |
| Remedy: | Format the HDD with SP5832-001. Replace the HDD. |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 902 |
| Display: | Power OFF/ON 902:Error |
| Description: | Engine software error |
| Causes: | These errors indicate an unrecoverable system software error. |
| Remedy: | Replace the system board. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
| Error code: | 999 |
| Display: | Service call 999: Error |
| Description: | Stapler Motor Error |
| Causes: | • Color registration (MUSIC) failure |
| Remedy: | 1 Are staples jammed in the stapler? Go to step 2. Go to step 3. 2 Clear the staple jam and run the staple test in diagnostic mode or run a staple job. Does the problem reoccur? Replace the staple cartridge and to go step 4. Problem solved. 3 Are the connectors CN5 on the stapler and PJ1 on the finisher control board securely connected? Go to step 5. Securely connect the connectors. 4 Did replacement of the stapler cartridge resolve the problem? Problem resolved. Replace the stapler. 5 Make sure the finisher set switch is activated. Measure for 5 V dc between pins 11 and 12 on stapler connector CN5. Is 5 V dc present? Replace the stapler. Replace the finisher control board. 6 Did replacement of the finisher control board correct the problem? Problem solved. Go to step 7. 7 Is there continuity on the stapler to finisher control board cable? Replace the power supply. Replace the cable. |
Парткод
Название
(885301) RICOH TYPE M2 Тонер-картридж черный
(885302) RICOH TYPE M2 Тонер-картридж желтый
(885303) RICOH TYPE M2 Тонер-картридж пурпурный
(885304) RICOH TYPE M2 Тонер-картридж голубой
RICOH TYPE SS Масло силиконовое
RICOH Бункер отработанного тонера
RICOH Блок фотобарабана
RICOH TYPE M2 Блок проявки пурпурный
RICOH TYPE M2 Блок проявки желтый
RICOH TYPE M2 Блок проявки голубой
RICOH TYPE M2 Блок проявки черный
RICOH Блок подачи масла
RICOH Блок фотобарабана
