Ricoh Aficio 2013MF
Рейтинг
Модули
OPTICS SECTION 2
FRAME SECTION
ADF 4
EXTERIOR
LASER UNIT
OPERATION PANEL
PAPER REGISTRATION
EXTENTION BOX
TRANSPORT SECTION
OPTICS SECTION 1
PAPER CASSETTE
BY-PASS FEED UNIT
ELECTRICAL SECTION
PCU SECTION
ADF 1
DRIVE SECTION
FUSING UNIT
FAX OP
ADF 3
ADF 2
Детали ELECTRICAL SECTION
| Деталь: | Front Idler Bracket |
| Парткод: | B044 1816 |
| Деталь: | Timing Belt 640t |
| Парткод: | AA04 3939 |
| Деталь: | Rear Idler Bracket |
| Парткод: | B044 1818 |
| Деталь: | Spring - Timing Pulley |
| Парткод: | B0391704 |
| Деталь: | Rear Rail |
| Парткод: | B044 1654 |
| Деталь: | Front Rail |
| Парткод: | B044 1653 |
| Деталь: | Photointerruptor - LG-248l1 |
| Парткод: | AW02 0119 |
| Деталь: | Scale Bracket |
| Парткод: | B044 1665 |
| Деталь: | Sheet - Flat Cable Stabilizer |
| Парткод: | B129 1667 |
| Деталь: | Lens Bracket |
| Парткод: | B044 1663 |
| Деталь: | Left DFB PCB Bracket |
| Парткод: | B129 1675 |
| Деталь: | Drive Pully - 41t/37t |
| Парткод: | AB03 3095 |
| Деталь: | Flange - Pulley |
| Парткод: | B0391695 |
| Деталь: | Scanner Drive Shaft |
| Парткод: | B044 1815 |
| Деталь: | Stepper Motor - DC 9.0W |
| Парткод: | B044 1810 |
| Деталь: | Gear - 53Z/60Z |
| Парткод: | B121 1680 |
| Деталь: | Timing Belt L147 |
| Парткод: | B121 1696 |
| Деталь: | Tension Spring - Stepper Motor |
| Парткод: | B0391683 |
| Деталь: | Drive Pully - 37t |
| Парткод: | AB030711 |
| Деталь: | Bushing - 6x12x6 |
| Парткод: | AA08 2046 |
| Деталь: | Belt Clamp Bracket |
| Парткод: | B044 1661 |
| Деталь: | BRACKET |
| Парткод: | B044 1671 |
| Деталь: | Stopper Bracket - 1st Scanner |
| Парткод: | B044 1669 |
| Деталь: | Rear Stopper Bracket |
| Парткод: | B044 1668 |
| Деталь: | DFB Harness Guide Plate |
| Парткод: | B129 1304 |
| Деталь: | Middle DFB PCB Bracket |
| Парткод: | B129 1676 |
| Деталь: | Speaker - GS |
| Парткод: | G025 1211 |
| Деталь: | Speaker bracket |
| Парткод: | B129 1311 |
| Деталь: | PCB DFB |
| Парткод: | B129 5170 |
| Деталь: | Harness - Sensor |
| Парткод: | B130 5231 |
| Деталь: | Core Holder |
| Парткод: | B044 1677 |
| Деталь: | Rubber Bushing |
| Парткод: | B044 1824 |
| Деталь: | COLLAR |
| Парткод: | B044 1825 |
| Деталь: | Harness - DFB |
| Парткод: | B130 5226 |
| Деталь: | Scanner Unit Stay |
| Парткод: | B044 1060 |
| Деталь: | Myler - Remove Paper Dust |
| Парткод: | B044 2623 |
| Деталь: | GROUND WIRE |
| Парткод: | B044 5235 |
| Деталь: | BICU Shadeing Plate |
| Парткод: | B129 1301 |
| Деталь: | BICU Bracket |
| Парткод: | B129 1300 |
| Деталь: | RUBBER FOOT |
| Парткод: | G512 3029 |
| Деталь: | Right Rail |
| Парткод: | B044 2651 |
| Деталь: | Paper End Sensor |
| Парткод: | B044 5300 |
| Деталь: | PSU Stay |
| Парткод: | B129 1060 |
| Деталь: | Ground Plate - Option Tray |
| Парткод: | B044 1066 |
| Деталь: | Positioning Plate - Toner Bottle |
| Парткод: | B044 1105 |
| Деталь: | Base Bracket |
| Парткод: | B044 1061 |
| Деталь: | Base Bracket - Paper Feed |
| Парткод: | B044 1062 |
| Деталь: | Mylar-quenching Lamp |
| Парткод: | B044 2202 |
| Деталь: | Choke Coil - B1295053 |
| Парткод: | B129 5053 |
| Деталь: | Power Supply Unit Bracket |
| Парткод: | B129 1302 |
| Деталь: | Holder Assy - Paper Dust Removal |
| Парткод: | B044 2617 |
| Деталь: | Harness Holder Bracket |
| Парткод: | B044 1998 |
| Деталь: | Separation Bracket |
| Парткод: | B129 1315 |
| Деталь: | Harness - Sensor |
| Парткод: | B130 5231 |
| Деталь: | ROLLER |
| Парткод: | AF02 0600 |
| Деталь: | SHAFT |
| Парткод: | AF02 0553 |
| Деталь: | SHAFT |
| Парткод: | B044 4903 |
| Деталь: | ROLLER |
| Парткод: | AF02 0552 |
| Деталь: | Photo Reflection Sensor |
| Парткод: | AW01 0049 |
| Деталь: | Front Ground Plate |
| Парткод: | B044 4898 |
| Деталь: | Busing |
| Парткод: | H521 1311 |
| Деталь: | Gear-19z |
| Парткод: | AB01 1327 |
| Деталь: | Pressure Plate Spring - Rear |
| Парткод: | AA06 3868 |
| Деталь: | MOTOR BRACKET |
| Парткод: | B129 4912 |
| Деталь: | Gear - 14/44Z |
| Парткод: | H556 1315 |
| Деталь: | Gear - 22Z |
| Парткод: | AB01 1328 |
| Деталь: | Harness - On Off Detector |
| Парткод: | B130 5230 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Gear -17Z |
| Парткод: | AB01 1326 |
| Деталь: | Timing Belt Collar |
| Парткод: | AA08 0324 |
| Деталь: | Rear Ground Plate |
| Парткод: | H556 1303 |
| Деталь: | PULLEY |
| Парткод: | AB030712 |
| Деталь: | Timing Belt - 113T |
| Парткод: | AA04 3503 |
| Деталь: | Gear - 16/44Z |
| Парткод: | AB01 7689 |
| Деталь: | ADF Ground Wire |
| Парткод: | B044 4970 |
| Деталь: | Rear Lock Lever |
| Парткод: | B044 4906 |
| Деталь: | Spring Plate:Lock:Rear |
| Парткод: | H556 1300 |
| Деталь: | Rear Drive Bracket Assy |
| Парткод: | B129 4901 |
| Деталь: | Inner Cover-motor |
| Парткод: | B044 4883 |
| Деталь: | Cover Switch - Fusing Exit |
| Парткод: | H515 5018 |
| Деталь: | Stepper Motor ADF |
| Парткод: | AX05 0204 |
| Деталь: | Stepper Motor Cushion Assy |
| Парткод: | AA16 1630 |
| Деталь: | Inner Back Scale EU |
| Парткод: | B129 1847 |
| Деталь: | Inner Back Scale NA |
| Парткод: | B129 1848 |
| Деталь: | SHOULDER SCREW |
| Парткод: | B044 1843 |
| Деталь: | Operation Panel NA Assy (B129) |
| Парткод: | B129 1411 |
| Деталь: | Operation Panel EU (B129) |
| Парткод: | B129 1412 |
| Деталь: | Operation Panel CPSF NA (B130/B169) |
| Парткод: | B130 1411 |
| Деталь: | Operation Panel CPSF EU (B130/B169) |
| Парткод: | B130 1412 |
| Деталь: | Operation Panel CPSF AA (B130/B169) |
| Парткод: | B130 1413 |
| Деталь: | Operation Panel NA Assy (B168) |
| Парткод: | B168 1413 |
| Деталь: | Operation Panel EU Assy (B168) |
| Парткод: | B168 1414 |
| Деталь: | Operation Panel ASIA Assy (B168) |
| Парткод: | B168 1415 |
| Деталь: | Platen Cover (NA) |
| Парткод: | B044 1394 |
| Деталь: | Platen Cover (EU) |
| Парткод: | B044 1393 |
| Деталь: | Hinge Cover |
| Парткод: | B044 1384 |
| Деталь: | Platen Cover Spring |
| Парткод: | B044 1383 |
| Деталь: | Platen Cover Hinge |
| Парткод: | B044 1381 |
| Деталь: | Platen Cover Sheet |
| Парткод: | B044 1385 |
| Деталь: | Platen Cover Stopper |
| Парткод: | B044 1388 |
| Деталь: | Stopper Bracket - Platen Cover |
| Парткод: | B044 1389 |
| Деталь: | Exposure Glass |
| Парткод: | AC01 2069 |
| Деталь: | Left Scale Assy - EU (B169) |
| Парткод: | B044 1802 |
| Деталь: | Platen Cover Shaft |
| Парткод: | B044 1390 |
| Деталь: | Platen Cover Shaft |
| Парткод: | B044 1392 |
| Деталь: | Rear Cover EU |
| Парткод: | B129 1250 |
| Деталь: | Rear Cover NA |
| Парткод: | B129 1260 |
| Деталь: | Right Upper Cover - NA |
| Парткод: | B129 1266 |
| Деталь: | Right Upper Cover - EU |
| Парткод: | B129 1256 |
| Деталь: | Front Right Coveer (NA) |
| Парткод: | B044 1279 |
| Деталь: | Right Upper Cover (EU) |
| Парткод: | B044 1278 |
| Деталь: | Sheet - Operation Instructions |
| Парткод: | B044 1290 |
| Деталь: | Front door |
| Парткод: | B044 1280 |
| Деталь: | FRONT LEFT COVER |
| Парткод: | B044 1415 |
| Деталь: | Left Scanner Cover EU |
| Парткод: | B129 1251 |
| Деталь: | Left Scanner Cover NA |
| Парткод: | B129 1261 |
| Деталь: | Energy Decal |
| Парткод: | GA00 3035 |
| Деталь: | Platen Cover Assy - EU (B169) |
| Парткод: | B044 1241 |
| Деталь: | END FENCE |
| Парткод: | B044 1254 |
| Деталь: | Extension Tray - EU |
| Парткод: | B044 1284 |
| Деталь: | Extension Tray - NA |
| Парткод: | B044 1285 |
| Деталь: | Exit Cover NA |
| Парткод: | B129 1262 |
| Деталь: | Exit Cover EU |
| Парткод: | B129 1252 |
| Деталь: | Shielding Plate |
| Парткод: | B044 1258 |
| Деталь: | Original Holder - EU |
| Парткод: | B044 1395 |
| Деталь: | Function Decal - Fax |
| Парткод: | B130 7400 |
| Деталь: | Decal - Paper Size |
| Парткод: | H555 2790 |
| Деталь: | IC Card Cover |
| Парткод: | B129 1253 |
| Деталь: | Model Name Plate - GES DSM415pF |
| Парткод: | B130 7519 |
| Деталь: | Model Name Plate (B168 GES) |
| Парткод: | B168 7508 |
| Деталь: | Model Name Plate - NSA DSM415F |
| Парткод: | B168 7509 |
| Деталь: | Model Name Plate - RIC AF1515F |
| Парткод: | B168 7512 |
| Деталь: | Model Name Plate (B168 REX) |
| Парткод: | B168 7514 |
| Деталь: | Model Name Plate - LAN LD015F |
| Парткод: | B168 7516 |
| Деталь: | Model Name Plate - INF IS2215F |
| Парткод: | B168 7518 |
| Деталь: | Model Name Plate - GES DSM415F |
| Парткод: | B168 7519 |
| Деталь: | Model Name Plate - NSA DSM415P |
| Парткод: | B169 7509 |
| Деталь: | Model Name Plate - RIC AF1515PS |
| Парткод: | B169 7512 |
| Деталь: | Model Name Plate - REX DSM415P |
| Парткод: | B169 7514 |
| Деталь: | Model Name Plate - LAN LD015SP |
| Парткод: | B169 7516 |
| Деталь: | Model Name Plate - INF IS2215PS |
| Парткод: | B169 7518 |
| Деталь: | Model Name Plate - GES DSM415P |
| Парткод: | B169 7519 |
| Деталь: | Model Name Plate (B129 RIC TWN) |
| Парткод: | B129 7508 |
| Деталь: | Model Name Plate - NSA DSM415 |
| Парткод: | B129 7509 |
| Деталь: | Model Name Plate - RIC AF1515 |
| Парткод: | B129 7512 |
| Деталь: | Model Name Plate - REX DSM415 |
| Парткод: | B129 7514 |
| Деталь: | Model Name Plate - LAN LD015 |
| Парткод: | B129 7516 |
| Деталь: | Model Name Plate - INF IS2215 |
| Парткод: | B129 7518 |
| Деталь: | Model Name Plate - GES DSM415 |
| Парткод: | B129 7519 |
| Деталь: | Model Name Plate (B130 RIC TWN) |
| Парткод: | B130 7508 |
| Деталь: | Model Name Plate - NSA DSM415pF |
| Парткод: | B130 7509 |
| Деталь: | Model Name Plate - RIC AF1515MF |
| Парткод: | B130 7512 |
| Деталь: | Model Name Plate - Rex DSM415pF |
| Парткод: | B130 7514 |
| Деталь: | Model Name Plate - LAN LD015SpF |
| Парткод: | B130 7516 |
| Деталь: | Model Name Plate - INF IS2215FPS |
| Парткод: | B130 7518 |
| Деталь: | Telephone Cable |
| Парткод: | H523 5350 |
| Деталь: | Handset Bracket |
| Парткод: | B404 5821 |
| Деталь: | Laser Unit Assy |
| Парткод: | B129 1901 |
| Деталь: | GROUND PLATE |
| Парткод: | B044 1943 |
| Деталь: | Harness - LDDR |
| Парткод: | B129 5204 |
| Деталь: | Shutter Plate |
| Парткод: | B044 1944 |
| Деталь: | Harness - Polygon Scanner |
| Парткод: | B044 1935 |
| Деталь: | Polygon Scanner Motor |
| Парткод: | AX06 0284 |
| Деталь: | Laser Diode Unit |
| Парткод: | B044 1911 |
| Деталь: | Cylindrical Lens |
| Парткод: | G025 2730 |
| Деталь: | Synchronizing Detector Lens |
| Парткод: | G025 2731 |
| Деталь: | Shield Glass |
| Парткод: | B044 1931 |
| Деталь: | Laser Unit Cover |
| Парткод: | B044 1941 |
| Деталь: | LD Decal |
| Парткод: | G029 1982 |
| Деталь: | Seal - LDU |
| Парткод: | B044 1906 |
| Деталь: | Spacer - 5mm |
| Парткод: | B044 1999 |
| Деталь: | Operation Panel NA Assy (B129) |
| Парткод: | B129 1411 |
| Деталь: | Operation Panel EU (B129) |
| Парткод: | B129 1412 |
| Деталь: | Operation Panel CPSF NA (B130/B169) |
| Парткод: | B130 1411 |
| Деталь: | Operation Panel CPSF EU (B130/B169) |
| Парткод: | B130 1412 |
| Деталь: | Operation Panel CPSF AA (B130/B169) |
| Парткод: | B130 1413 |
| Деталь: | Operation Panel NA Assy (B168) |
| Парткод: | B168 1413 |
| Деталь: | Operation Panel EU Assy (B168) |
| Парткод: | B168 1414 |
| Деталь: | Operation Panel ASIA Assy (B168) |
| Парткод: | B168 1415 |
| Деталь: | OP Case |
| Парткод: | B129 1451 |
| Деталь: | Panel Sheet - NA/ASIA |
| Парткод: | B129 1476 |
| Деталь: | Panel Sheet - EU |
| Парткод: | B129 1492 |
| Деталь: | Sheet - Power Sourse - NA/ASIA |
| Парткод: | B129 1475 |
| Деталь: | Sheet - Power Sourse - EU |
| Парткод: | B129 1491 |
| Деталь: | Keytop - Copy Option NA |
| Парткод: | B129 1465 |
| Деталь: | Keytop - Copy Option EU |
| Парткод: | B129 1487 |
| Деталь: | Keytop - Printer Option NA |
| Парткод: | B129 1466 |
| Деталь: | Keytop - Printer Option EU |
| Парткод: | B129 1488 |
| Деталь: | Data In Lens |
| Парткод: | B129 1472 |
| Деталь: | On-line Display Sheet EU |
| Парткод: | B129 1493 |
| Деталь: | On-line Cover |
| Парткод: | B129 1455 |
| Деталь: | Spacer - Keytop Option |
| Парткод: | B129 1471 |
| Деталь: | Keytop - Counter |
| Парткод: | B129 1462 |
| Деталь: | Keytop - Clear Modes |
| Парткод: | B129 1461 |
| Деталь: | Keytop - Cursor |
| Парткод: | B129 1463 |
| Деталь: | Keytop - 10key NA |
| Парткод: | B129 1460 |
| Деталь: | Keytop - 10key EU |
| Парткод: | B129 1486 |
| Деталь: | Keytop - 10key Asia |
| Парткод: | B129 1502 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B129 1458 |
| Деталь: | Keytop - Start |
| Парткод: | B0391453 |
| Деталь: | Keytop - LCD Lower Coupling |
| Парткод: | B129 1464 |
| Деталь: | OP Sheet - Right |
| Парткод: | B129 1483 |
| Деталь: | Keytop - Main SW |
| Парткод: | B129 1459 |
| Деталь: | LCD |
| Парткод: | B129 1495 |
| Деталь: | PCB OPU Basic Assy |
| Парткод: | B129 5150 |
| Деталь: | Spring Plate - STL |
| Парткод: | B129 1474 |
| Деталь: | Blind On-line Cover |
| Парткод: | B129 1485 |
| Деталь: | LOWER COVER |
| Парткод: | B129 1452 |
| Деталь: | Blind Keytop Cover |
| Парткод: | B129 1484 |
| Деталь: | Scanner Bracket - Front Right |
| Парткод: | B044 1064 |
| Деталь: | Scanner Stud |
| Парткод: | B044 1063 |
| Деталь: | Guide Plate - Paper Feed |
| Парткод: | B044 2653 |
| Деталь: | Paper Feedguide |
| Парткод: | B044 2654 |
| Деталь: | C Ring - Paper Feed Roller |
| Парткод: | H521 3355 |
| Деталь: | REGISTRATION CLUTCH |
| Парткод: | AX20 0267 |
| Деталь: | Rear bushing |
| Парткод: | B044 2605 |
| Деталь: | Registration Roller |
| Парткод: | AF02 0550 |
| Деталь: | Photointerruptor - LG-248l1 |
| Парткод: | AW02 0119 |
| Деталь: | Registration Electrode Plate |
| Парткод: | B044 1102 |
| Деталь: | Front bushing |
| Парткод: | B044 2604 |
| Деталь: | Harness - Front Right Switch |
| Парткод: | B129 5211 |
| Деталь: | Registration Feeler |
| Парткод: | B044 2603 |
| Деталь: | Support Bushing |
| Парткод: | B044 2616 |
| Деталь: | Turn Roller |
| Парткод: | B044 2602 |
| Деталь: | Exit Guide |
| Парткод: | B044 2814 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0322 |
| Деталь: | Friction Pad - Manual Feed |
| Парткод: | B044 2815 |
| Деталь: | Fricion Pad Spring |
| Парткод: | B044 2817 |
| Деталь: | By-pass Feed Roller |
| Парткод: | AF031060 |
| Деталь: | Harness - Paper End Sensor |
| Парткод: | H555 5105 |
| Деталь: | Manual Feed Shaft |
| Парткод: | B044 2813 |
| Деталь: | Guide Plate - Manual Feed |
| Парткод: | B044 2811 |
| Деталь: | By-pass Paper End Sensor |
| Парткод: | G020 2772 |
| Деталь: | Manual Feed Bracket |
| Парткод: | B044 2812 |
| Деталь: | Spacer-manual Feed Roller |
| Парткод: | B044 2825 |
| Деталь: | Cushion-manual Feed Roller |
| Парткод: | B044 2824 |
| Деталь: | Manual Feed Clutch |
| Парткод: | AX20 0269 |
| Деталь: | Guide Plate Stopper |
| Парткод: | B044 2656 |
| Деталь: | Spacer - Registration |
| Парткод: | B044 2622 |
| Деталь: | Fusing Plate Nut |
| Парткод: | B044 4200 |
| Деталь: | SD-Card EXP Assy |
| Парткод: | B683 5670 |
| Деталь: | PCB CTL EXP |
| Парткод: | B683 5700 |
| Деталь: | Rail:Right |
| Парткод: | B622 5831 |
| Деталь: | PCB SDRAM-DIMM 128Mb Assy |
| Парткод: | G331 5720 |
| Деталь: | GWCTL Shadeing Plate |
| Парткод: | B129 1306 |
| Деталь: | Gwctl Bracket |
| Парткод: | B129 1305 |
| Деталь: | Cover - SD |
| Парткод: | B129 1254 |
| Деталь: | PCB USB Assy |
| Парткод: | B622 5660 |
| Деталь: | Interface Cover |
| Парткод: | B129 1309 |
| Деталь: | FCU Bracket |
| Парткод: | B129 1308 |
| Деталь: | PCB GWFCU3 NA:Assy |
| Парткод: | B620 5172 |
| Деталь: | PCB GWFCU3 EU Assy |
| Парткод: | B620 5174 |
| Деталь: | PCB MBU Assy |
| Парткод: | B130 5080 |
| Деталь: | Harness - Speaker |
| Парткод: | B130 5233 |
| Деталь: | Rail:Left |
| Парткод: | B622 5832 |
| Деталь: | Knob Screw |
| Парткод: | B622 5823 |
| Деталь: | Guide Plate Sponge |
| Парткод: | H547 4203 |
| Деталь: | Opif Rail |
| Парткод: | H556 5857 |
| Деталь: | GUIDE PLATE |
| Парткод: | B044 2612 |
| Деталь: | Registration Roller Shaft |
| Парткод: | B044 2613 |
| Деталь: | SPRING HOLDER |
| Парткод: | B044 4618 |
| Деталь: | Driven Roller Bushing |
| Парткод: | B044 2614 |
| Деталь: | Driven Roller - Front Rear |
| Парткод: | AF02 2139 |
| Деталь: | Middle Driven Roller |
| Парткод: | AF02 2140 |
| Деталь: | Right Door Spring |
| Парткод: | AA06 3409 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | B044 3802 |
| Деталь: | Positioning Spring - Transfer Roller |
| Парткод: | B044 3990 |
| Деталь: | Transfer Roller Spring - Rear |
| Парткод: | B044 3866 |
| Деталь: | Transfer Roller Spring - Front |
| Парткод: | B044 3865 |
| Деталь: | TRANSFER PLATE |
| Парткод: | B044 3860 |
| Деталь: | PRESSURE SPRING |
| Парткод: | B044 2615 |
| Деталь: | Transfer Guide |
| Парткод: | B044 3870 |
| Деталь: | ID SENSOR |
| Парткод: | B044 3892 |
| Деталь: | ID Sensor Harness |
| Парткод: | B044 5214 |
| Деталь: | Bushing - Driven Roller |
| Парткод: | B044 2621 |
| Деталь: | Reverse Guide Plate |
| Парткод: | B044 4663 |
| Деталь: | Separation Plate |
| Парткод: | B044 3857 |
| Деталь: | Right Door Belt |
| Парткод: | B044 4624 |
| Деталь: | Right Cover Lever |
| Парткод: | B044 4616 |
| Деталь: | RIGHT DOOR |
| Парткод: | B044 4655 |
| Деталь: | Discharge Plate |
| Парткод: | B044 3859 |
| Деталь: | Fusing Unit Decal |
| Парткод: | B044 4617 |
| Деталь: | GUIDE PLATE |
| Парткод: | H556 2818 |
| Деталь: | Duplex Guide Plate Assy |
| Парткод: | H556 4154 |
| Деталь: | Guide Roller |
| Парткод: | AF02 2143 |
| Деталь: | Myler Reverse |
| Парткод: | H556 2820 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 3405 |
| Деталь: | Right Guide Plate |
| Парткод: | H556 4192 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 2033 |
| Деталь: | Positioning Roller |
| Парткод: | H556 4186 |
| Деталь: | Spring Plate |
| Парткод: | H556 4181 |
| Деталь: | Transport Roller Holder |
| Парткод: | H556 4185 |
| Деталь: | Transport Driven Roller |
| Парткод: | AF02 2152 |
| Деталь: | Transport Roller |
| Парткод: | H556 4187 |
| Деталь: | SHEET |
| Парткод: | H556 4188 |
| Деталь: | SHEET |
| Парткод: | H556 4189 |
| Деталь: | Front Stopper Plate |
| Парткод: | B044 2860 |
| Деталь: | Rear Stopper Plate |
| Парткод: | B044 2861 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | No.1 Carriage Assy |
| Парткод: | B129 1700 |
| Деталь: | Lamp Stabilizer Harness |
| Парткод: | B044 1717 |
| Деталь: | Xenon Lamp Stabilizer |
| Парткод: | AZ50 0065 |
| Деталь: | Xenon Lamp |
| Парткод: | AX50 0084 |
| Деталь: | Timing Belt Holder |
| Парткод: | B044 1715 |
| Деталь: | 1st Mirror |
| Парткод: | AC03 0145 |
| Деталь: | 1st Mirror Holder |
| Парткод: | B044 1721 |
| Деталь: | Flat Cable - SBU |
| Парткод: | B129 5236 |
| Деталь: | Optical Unit CCD Assy |
| Парткод: | B129 1770 |
| Деталь: | Rear Pulley Bracket |
| Парткод: | B044 1745 |
| Деталь: | Front Pulley Bracket |
| Парткод: | B044 1741 |
| Деталь: | SCANNER DRIVE PULLEY |
| Парткод: | B0391785 |
| Деталь: | TENSION SPRING |
| Парткод: | B0391786 |
| Деталь: | 2nd Scanner |
| Парткод: | B044 1730 |
| Деталь: | Scanner drive belt |
| Парткод: | AA04 2052 |
| Деталь: | 2nd Mirror |
| Парткод: | AC03 0146 |
| Деталь: | 2nd Mirror Holder |
| Парткод: | B0391781 |
| Деталь: | Flat Cable Guide |
| Парткод: | B044 1751 |
| Деталь: | Supporting Plate |
| Парткод: | B044 1683 |
| Деталь: | Exposure Glass Sheet |
| Парткод: | A2501824 |
| Деталь: | Photointerruptor - LG-248l1 |
| Парткод: | AW02 0119 |
| Деталь: | Scale Bracket |
| Парткод: | B044 1681 |
| Деталь: | FERRITE CORE |
| Парткод: | H555 5153 |
| Деталь: | Scanner Slider Pin |
| Парткод: | B044 1719 |
| Деталь: | PAPER TRAY UNIT |
| Парткод: | B044 2503 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B044 2704 |
| Деталь: | Front Side Fence |
| Парткод: | B044 2702 |
| Деталь: | END FENCE |
| Парткод: | B044 2706 |
| Деталь: | SIDE FENCE GEAR |
| Парткод: | G800 3133 |
| Деталь: | GROUND PLATE |
| Парткод: | B044 2709 |
| Деталь: | PRESSURE SPRING |
| Парткод: | B044 2716 |
| Деталь: | Rear Side Fence |
| Парткод: | B044 2703 |
| Деталь: | Joint - Paper Feed Roller |
| Парткод: | B044 2751 |
| Деталь: | Spring - Paper Feed Roller |
| Парткод: | B044 2756 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | B044 2755 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | AF03 1061 |
| Деталь: | Friction pad |
| Парткод: | B044 2710 |
| Деталь: | STOPPER |
| Парткод: | B044 2713 |
| Деталь: | Spring - Release Lever |
| Парткод: | G020 2599 |
| Деталь: | C Ring - Paper Feed Roller |
| Парткод: | H521 3355 |
| Деталь: | GROUND PLATE |
| Парткод: | B044 2711 |
| Деталь: | PAPER TRAY |
| Парткод: | B044 2701 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 52 152 713 |
| Деталь: | Decal - Cassette Operation |
| Парткод: | B044 2720 |
| Деталь: | PRESSURE SPRING |
| Парткод: | B044 2717 |
| Деталь: | Sponge - End Fence |
| Парткод: | B044 2715 |
| Деталь: | Paper Tray Sheet |
| Парткод: | B044 2721 |
| Деталь: | Rubber Plate - Friction Pad |
| Парткод: | B044 2714 |
| Деталь: | PAPER GUIDE |
| Парткод: | B044 2808 |
| Деталь: | By-pass Feed Table |
| Парткод: | B044 2801 |
| Деталь: | Spring - Manual Feed Table |
| Парткод: | B044 2809 |
| Деталь: | Shaft - Manual Release Lever |
| Парткод: | G020 2786 |
| Деталь: | Lever - Manual Feed Table |
| Парткод: | B044 2806 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Front Side Fence |
| Парткод: | B044 2804 |
| Деталь: | Rear Side Fence |
| Парткод: | B044 2805 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B044 2803 |
| Деталь: | SIDE FENCE GEAR |
| Парткод: | G800 3133 |
| Деталь: | Stay - Tray Bottom Plate |
| Парткод: | B044 2807 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 52 152 713 |
| Деталь: | Manual Feed Decal |
| Парткод: | AA00 3011 |
| Деталь: | Fan Motor - DC24V |
| Парткод: | GX64 0020 |
| Деталь: | Power Pack BCT |
| Парткод: | AZ320131 |
| Деталь: | Harness - HVP |
| Парткод: | B129 5217 |
| Деталь: | Harness - HPS |
| Парткод: | B129 5201 |
| Деталь: | Harness - Paper Feed Sensor |
| Парткод: | B129 5202 |
| Деталь: | Harness - Registration Sensor |
| Парткод: | B129 5213 |
| Деталь: | Harness - Toner |
| Парткод: | B129 5200 |
| Деталь: | Harness - Power Supply Unit |
| Парткод: | B129 5206 |
| Деталь: | Harness - Main Motor |
| Парткод: | B129 5216 |
| Деталь: | Harness - Operation Panel |
| Парткод: | B129 5205 |
| Деталь: | Harness - Door Switch |
| Парткод: | B129 5210 |
| Деталь: | PCB BICU EXP Assy |
| Парткод: | B129 5101 |
| Деталь: | PCB BICU Chn Assy |
| Парткод: | B129 5104 |
| Деталь: | PCB BICU MFP EXP Assy |
| Парткод: | B130 5101 |
| Деталь: | PCB BICU MFP Asia Assy |
| Парткод: | B130 5103 |
| Деталь: | PCB BICU MFP CHN Assy |
| Парткод: | B130 5104 |
| Деталь: | PCB BICU Asia Assy |
| Парткод: | B129 5013 |
| Деталь: | BICU Insulating Sheet |
| Парткод: | B129 1307 |
| Деталь: | Insulating Sheet Power Pack |
| Парткод: | AA17 0026 |
| Деталь: | BICU Shadeing Plate |
| Парткод: | B129 1301 |
| Деталь: | Power Supply Cord NA |
| Парткод: | B129 5021 |
| Деталь: | Power Supply Cord - CHN |
| Парткод: | H555 5004 |
| Деталь: | POWER SUPPLY CORD |
| Парткод: | H555 5008 |
| Деталь: | Harness - Paper Feed Table |
| Парткод: | B129 5223 |
| Деталь: | Spring Plate - Gwctl |
| Парткод: | B129 1313 |
| Деталь: | Rear Cover Bracket |
| Парткод: | B129 1303 |
| Деталь: | Power Supply Unit 100V |
| Парткод: | AZ23 0134 |
| Деталь: | Power Supply Unit 200V |
| Парткод: | AZ23 0135 |
| Деталь: | Harness - AC Fusing EU |
| Парткод: | B129 5208 |
| Деталь: | Harness - AC Fusing NA |
| Парткод: | B129 5209 |
| Деталь: | Total Counter 2nd |
| Парткод: | AX31 0038 |
| Деталь: | Ferrite Core Holder |
| Парткод: | B044 5805 |
| Деталь: | FERRITE CORE |
| Парткод: | H555 5150 |
| Деталь: | Flat Cable - SBU |
| Парткод: | B129 5236 |
| Деталь: | Cover Plate - BICU (B129) |
| Парткод: | B129 1314 |
| Деталь: | Duct Shield |
| Парткод: | B044 1069 |
| Деталь: | Quenching Lamp |
| Парткод: | AX50 0079 |
| Деталь: | Toner Supply Shaft |
| Парткод: | B129 1176 |
| Деталь: | Toner Bottle Drive Spring |
| Парткод: | B1291175 |
| Деталь: | SPRING CLUTCH |
| Парткод: | AB04 0019 |
| Деталь: | Toner Supply Rail |
| Парткод: | B044 1068 |
| Деталь: | Gear -64Z |
| Парткод: | AB01 0358 |
| Деталь: | Electrode Plate - Charge |
| Парткод: | AA11 3034 |
| Деталь: | Harness - High Voltage Line C |
| Парткод: | B129 5220 |
| Деталь: | HVP T Harness |
| Парткод: | B129 5222 |
| Деталь: | Electrode Plate - Transfer |
| Парткод: | AA11 3035 |
| Деталь: | Electrode Plate - Development |
| Парткод: | AA11 3032 |
| Деталь: | Harness - High Voltage Line B |
| Парткод: | B129 5221 |
| Деталь: | Coupled Gear 22/50z |
| Парткод: | AB01 7582 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | AA14 8651 |
| Деталь: | Drum Shaft |
| Парткод: | AB00 0022 |
| Деталь: | SHUTTER |
| Парткод: | B044 1100 |
| Деталь: | SHUTTER SPRING |
| Парткод: | B044 1101 |
| Деталь: | Development Shaft Assy |
| Парткод: | AB00 0024 |
| Деталь: | Shutter Cover |
| Парткод: | B044 1103 |
| Деталь: | Snap Ring - Pick Up |
| Парткод: | G014 3291 |
| Деталь: | Toner Supply Unit Assy |
| Парткод: | B129 3020 |
| Деталь: | Bottle Chuck |
| Парткод: | A184 3420 |
| Деталь: | Chuck Shaft |
| Парткод: | B044 3426 |
| Деталь: | Slide Shaft |
| Парткод: | B044 3425 |
| Деталь: | Handle Cam |
| Парткод: | B044 3460 |
| Деталь: | Chuck Spring - Tonner Bottle |
| Парткод: | A267 3556 |
| Деталь: | SLIDER ASSY |
| Парткод: | B044 3485 |
| Деталь: | Cover - Toner Supply Unit |
| Парткод: | B129 3465 |
| Деталь: | Fusing Plate Nut |
| Парткод: | B044 4200 |
| Деталь: | Toner Supply Rail |
| Парткод: | B044 1067 |
| Деталь: | Un Lock Grip |
| Парткод: | B044 3475 |
| Деталь: | Toner Supply Case Assy |
| Парткод: | B044 3470 |
| Деталь: | Cover- Original Table |
| Парткод: | B044 4952 |
| Деталь: | Gear - 14Z |
| Парткод: | BB01 3003 |
| Деталь: | Rear Guide |
| Парткод: | B044 4951 |
| Деталь: | FRONT GUIDE |
| Парткод: | B044 4950 |
| Деталь: | Original Table |
| Парткод: | B044 4948 |
| Деталь: | Platen Cover Hinge |
| Парткод: | B044 1381 |
| Деталь: | Platen Cover Spring |
| Парткод: | B044 1383 |
| Деталь: | Hinge Cover |
| Парткод: | B044 1384 |
| Деталь: | Platen Cover |
| Парткод: | B044 1393 |
| Деталь: | Platen Cover |
| Парткод: | B044 1394 |
| Деталь: | Platen Cover Sheet |
| Парткод: | B044 1385 |
| Деталь: | Original Insert Decal |
| Парткод: | B044 4999 |
| Деталь: | Original Auxiliary Table - NA |
| Парткод: | B044 4953 |
| Деталь: | Gear -27Z |
| Парткод: | BB01 3006 |
| Деталь: | Coupled Gear - 43/53z |
| Парткод: | AB01 7586 |
| Деталь: | Gear - 41Z |
| Парткод: | AB01 1438 |
| Деталь: | GEAR - 29Z |
| Парткод: | AB01 1492 |
| Деталь: | PAPER FEED CLUTCH |
| Парткод: | AX20 0268 |
| Деталь: | COLLAR |
| Парткод: | AA13 2217 |
| Деталь: | Coupled Gear - 17/44z |
| Парткод: | AB01 7587 |
| Деталь: | Coupled Gear - 17/44z |
| Парткод: | AB01 7585 |
| Деталь: | Gear - 19/21Z |
| Парткод: | AB01 7629 |
| Деталь: | Gear - 18/40Z |
| Парткод: | AB01 7663 |
| Деталь: | Fusing Bracket Assy |
| Парткод: | B129 1162 |
| Деталь: | Fusing Shaft No.5 |
| Парткод: | AA14 3783 |
| Деталь: | Rear Drive Plate 2 |
| Парткод: | B129 1110 |
| Деталь: | Bracket Cushion |
| Парткод: | AA16 1157 |
| Деталь: | SHAFT SPACER |
| Парткод: | B129 1056 |
| Деталь: | Lever DC Solenoid Assy |
| Парткод: | B129 1161 |
| Деталь: | Spring - Swivel Fusing |
| Парткод: | AA06 2326 |
| Деталь: | Plate Cushion |
| Парткод: | B129 1129 |
| Деталь: | Damping Insulation |
| Парткод: | B044 1139 |
| Деталь: | Ground Plate - Drum Drive |
| Парткод: | AA120124 |
| Деталь: | Ground Plate - Registration |
| Парткод: | AA120104 |
| Деталь: | Side Plate - Manual Feed |
| Парткод: | B1291157 |
| Деталь: | Ground Plate - Manual Feed |
| Парткод: | B129 2820 |
| Деталь: | Duplex Drive Bracket |
| Парткод: | H556 4170 |
| Деталь: | Duplex Stepper Motor |
| Парткод: | AX06 0273 |
| Деталь: | Ground Plate - Lower Duplex Bracket |
| Парткод: | B129 4703 |
| Деталь: | Spring Plate - Discharge Bracket Motor |
| Парткод: | B129 4701 |
| Деталь: | Main Motor - DC20W |
| Парткод: | AX06 0226 |
| Деталь: | Gear - 19/38Z |
| Парткод: | AB01 7628 |
| Деталь: | Rear Drive Plate 1 Assy |
| Парткод: | B129 1160 |
| Деталь: | Swivel Bracket |
| Парткод: | H556 4179 |
| Деталь: | Spring Plate |
| Парткод: | H556 4178 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3582 |
| Деталь: | Pulley - 24Z |
| Парткод: | AB03 2071 |
| Деталь: | Plate Bracket |
| Парткод: | H556 4180 |
| Деталь: | Bushing - Cleaning Roller |
| Парткод: | 54 244 142 |
| Деталь: | Gear - 29/69Z |
| Парткод: | AB01 7661 |
| Деталь: | Gear - 44/67Z |
| Парткод: | AB01 7660 |
| Деталь: | Gear - 17/67Z |
| Парткод: | AB01 7662 |
| Деталь: | Gear - 49Z |
| Парткод: | AB01 0362 |
| Деталь: | Gear - 43/91Z |
| Парткод: | AB01 7659 |
| Деталь: | BRACKET |
| Парткод: | B044 11 58 |
| Деталь: | Gear - 28/43Z |
| Парткод: | AB01 7627 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Fusing Unit NA Assy |
| Парткод: | B129 4017 |
| Деталь: | Fusing Unit EU Assy |
| Парткод: | B129 4027 |
| Деталь: | Discharge Brush |
| Парткод: | B044 4165 |
| Деталь: | Spring Plate |
| Парткод: | B044 4166 |
| Деталь: | Feeler |
| Парткод: | B044 4183 |
| Деталь: | GUIDE PLATE |
| Парткод: | B044 4186 |
| Деталь: | SPRING |
| Парткод: | B044 4138 |
| Деталь: | Turn-roller |
| Парткод: | AF02 2141 |
| Деталь: | EXIT ROLLER |
| Парткод: | AF04 0603 |
| Деталь: | Middle Roller |
| Парткод: | AF02 2142 |
| Деталь: | EXIT ROLLER |
| Парткод: | AF04 0588 |
| Деталь: | Exit Spring |
| Парткод: | B044 4154 |
| Деталь: | Photointerruptor - LG-248l1 |
| Парткод: | AW02 0119 |
| Деталь: | Harness - Paper Feed Sensor |
| Парткод: | B129 5203 |
| Деталь: | Gear - 19/28Z |
| Парткод: | H556 2210 |
| Деталь: | STUD |
| Парткод: | H556 2218 |
| Деталь: | Electrode Plate Cover |
| Парткод: | B129 4143 |
| Деталь: | Fusing Frame |
| Парткод: | B129 4101 |
| Деталь: | Thermostat - 160c |
| Парткод: | AW11 0037 |
| Деталь: | Thermistor - Fusing |
| Парткод: | AW10 0088 |
| Деталь: | Thermostat - 170c |
| Парткод: | AW11 0038 |
| Деталь: | Spring - Pickoff Pawl |
| Парткод: | B044 4155 |
| Деталь: | Stripper Pawls |
| Парткод: | AE04 4059 |
| Деталь: | LAMP HOLDER |
| Парткод: | B044 4135 |
| Деталь: | Front Spring Plate |
| Парткод: | B044 4117 |
| Деталь: | GUIDE PLATE |
| Парткод: | H556 2206 |
| Деталь: | Rear Spring Plate |
| Парткод: | B044 4118 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AE02 0107 |
| Деталь: | PRESSURE SPRING |
| Парткод: | B044 4152 |
| Деталь: | PRESSURE LEVER |
| Парткод: | B044 4130 |
| Деталь: | Pressure Release Lever - Front |
| Парткод: | B044 4141 |
| Деталь: | Pressure Release Lever - Rear |
| Парткод: | B044 4146 |
| Деталь: | Side plate |
| Парткод: | B044 4132 |
| Деталь: | Pressure Roller Bushing |
| Парткод: | AE031035 |
| Деталь: | Fusing Plate Nut |
| Парткод: | B044 4200 |
| Деталь: | Fusing Harness Cover |
| Парткод: | B044 4201 |
| Деталь: | Warning Decal |
| Парткод: | B044 4161 |
| Деталь: | Pressure Frame |
| Парткод: | B044 4104 |
| Деталь: | Hot Roller Stopper |
| Парткод: | B044 4150 |
| Деталь: | Fusing Gear |
| Парткод: | B044 4170 |
| Деталь: | Fusing Bushing |
| Парткод: | AE03 1034 |
| Деталь: | Hot Roller |
| Парткод: | AE01 1086 |
| Деталь: | Heater - 120V/800W |
| Парткод: | AX44 0202 |
| Деталь: | Heater - 230V:750W |
| Парткод: | AX44 0203 |
| Деталь: | Screw - M3X13 |
| Парткод: | G029 4158 |
| Деталь: | Bushing-pressure Release |
| Парткод: | B044 4131 |
| Деталь: | CUSHION |
| Парткод: | B044 41 53 |
| Деталь: | Electrode Plate Fusing |
| Парткод: | B1294134 |
| Деталь: | GROUND PLATE |
| Парткод: | B044 4136 |
| Деталь: | Paper Holder Stand |
| Парткод: | B044 4401 |
| Деталь: | Spring Plate - Pickoff Pawl Roller |
| Парткод: | B1294139 |
| Деталь: | Stripper Pawls Roller |
| Парткод: | B0394170 |
| Деталь: | Hot Roller Cap |
| Парткод: | B044 4112 |
| Деталь: | Holder - Pickoff Pawl |
| Парткод: | B044 4179 |
| Деталь: | Thermostat Plate Nut |
| Парткод: | B129 4195 |
| Деталь: | Gate Plate |
| Парткод: | H556 2208 |
| Деталь: | Reargate Plate Guide |
| Парткод: | H556 2201 |
| Деталь: | Front Gate Plate Guide |
| Парткод: | H556 2202 |
| Деталь: | GEAR BRACKET |
| Парткод: | H556 2215 |
| Деталь: | ROLLER |
| Парткод: | H556 2220 |
| Деталь: | Gate Sensor Harness |
| Парткод: | H556 5106 |
| Деталь: | Hot Roller Spacer |
| Парткод: | B129 4111 |
| Деталь: | Front Hot Roller Stopper |
| Парткод: | B044 4156 |
| Деталь: | Operation Panel Expand FS NA |
| Парткод: | B130 1421 |
| Деталь: | Operation Panel Expand FS EU |
| Парткод: | B1301422 |
| Деталь: | Operation Panel Expand FS CHN |
| Парткод: | B1301427 |
| Деталь: | Operation Panel Expand NA Assy |
| Парткод: | B168 1423 |
| Деталь: | Operation Panel Expand EU Assy(B130/B169) |
| Парткод: | B1301424 |
| Деталь: | Operation Panel Expand EU Assy (B168) |
| Парткод: | B168 1424 |
| Деталь: | Operation PaneL Expand CHN Assy |
| Парткод: | B168 1425 |
| Деталь: | Sheet - OP Left |
| Парткод: | B129 1482 |
| Деталь: | Harness - OPU |
| Парткод: | B130 5290 |
| Деталь: | PCB OPU Assy |
| Парткод: | B130 5157 |
| Деталь: | Spring Plate - STL |
| Парткод: | B129 1474 |
| Деталь: | OP-l Cable Sheet |
| Парткод: | B129 1457 |
| Деталь: | Lower Cover - Fax |
| Парткод: | B129 1454 |
| Деталь: | Function Key Decal - NA/ASIA |
| Парткод: | B129 1481 |
| Деталь: | Function Cover Fax |
| Парткод: | B129 1456 |
| Деталь: | Keytop - Function Fax |
| Парткод: | B129 1470 |
| Деталь: | Upper Decal |
| Парткод: | B129 1478 |
| Деталь: | Sheet - Display Fax B |
| Парткод: | B129 1479 |
| Деталь: | Keytop - Dial Fax |
| Парткод: | B129 1469 |
| Деталь: | Upper Cover - Fax |
| Парткод: | B129 1453 |
| Деталь: | Keytop - Scanner Option NA |
| Парткод: | B129 1467 |
| Деталь: | Keytop - Scanner Option EU |
| Парткод: | B129 1489 |
| Деталь: | Keytop - Fax Option NA |
| Парткод: | B129 1468 |
| Деталь: | Keytop - Fax Option EU |
| Парткод: | B129 1490 |
| Деталь: | Cover - Function Fax Blind |
| Парткод: | B129 1494 |
| Деталь: | Feed Bracket |
| Парткод: | B044 4865 |
| Деталь: | Gear -18Z |
| Парткод: | AB01 1325 |
| Деталь: | SPRING CLUTCH |
| Парткод: | H085 1514 |
| Деталь: | FEED ROLLER |
| Парткод: | AF031062 |
| Деталь: | Clutch Roller |
| Парткод: | H3061288 |
| Деталь: | Gear-16z |
| Парткод: | AB01 1324 |
| Деталь: | Pickup Shaft |
| Парткод: | B044 4870 |
| Деталь: | Gear - Pickup Roller |
| Парткод: | H521 1287 |
| Деталь: | Collar - Pickup |
| Парткод: | H521 1288 |
| Деталь: | pickup roller |
| Парткод: | AF03 0363 |
| Деталь: | Pad - Pick-up |
| Парткод: | H521 1350 |
| Деталь: | Rear Guide Plate |
| Парткод: | B044 4960 |
| Деталь: | Separation Guide Plate |
| Парткод: | B044 4890 |
| Деталь: | Front Guide Plate |
| Парткод: | B044 4959 |
| Деталь: | Feed Shaft |
| Парткод: | B044 4869 |
| Деталь: | Spring Clutch - M6 |
| Парткод: | H521 1314 |
| Деталь: | Clutch Spacer |
| Парткод: | H006 2316 |
| Деталь: | Reverse Roller Holder |
| Парткод: | B044 4886 |
| Деталь: | Reverse Roller |
| Парткод: | AF03 2030 |
| Деталь: | Reverse Roller Shaft |
| Парткод: | B044 4885 |
| Деталь: | Rear Drive Gear |
| Парткод: | H306 1358 |
| Деталь: | Reverse Bracket |
| Парткод: | B044 4881 |
| Деталь: | Separation Shaft |
| Парткод: | B044 4879 |
| Деталь: | Oneway Clutch |
| Парткод: | B044 4961 |
| Деталь: | ADF Pressure Plate |
| Парткод: | B044 4831 |
| Деталь: | Discharge Brush |
| Парткод: | H5561301 |
| Деталь: | Pressure Reverse Spring |
| Парткод: | H306 1315 |
| Деталь: | Original Sensor |
| Парткод: | AW50 0026 |
| Деталь: | Front Spring Plate |
| Парткод: | B044 4878 |
| Деталь: | Pressure Plate Spring - Front |
| Парткод: | AA06 3869 |
| Деталь: | LOCK SPRING |
| Парткод: | AA06 6591 |
| Деталь: | Front Lock Lever |
| Парткод: | B044 4905 |
| Деталь: | Gear - 26Z |
| Парткод: | BB01 3002 |
| Деталь: | Gear - 18/30Z |
| Парткод: | AB01 7591 |
| Деталь: | Magnetic Clutch Cover |
| Парткод: | B044 4873 |
| Деталь: | Magnetic clutch |
| Парткод: | B044 4833 |
| Деталь: | Magnetic Clutch Bracket |
| Парткод: | B044 4902 |
| Деталь: | CUSHION |
| Парткод: | B044 4962 |
| Деталь: | Snap Ring |
| Парткод: | G020 1160 |
| Деталь: | SPACER |
| Парткод: | B044 4854 |
| Деталь: | Separation Myler |
| Парткод: | B044 4853 |
| Деталь: | Original Feed Unit |
| Парткод: | B044 4811 |
| Деталь: | UPPER COVER |
| Парткод: | B044 4852 |
| Деталь: | Myler Guide |
| Парткод: | B044 4851 |
| Деталь: | Covermylar |
| Парткод: | B044 4850 |
| Деталь: | PRESSURE SPRING |
| Парткод: | B044 4859 |
| Деталь: | Roller Collar |
| Парткод: | AA08 0323 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AF02 2145 |
| Деталь: | PRESSURE SHAFT |
| Парткод: | AA14 5825 |
| Деталь: | PLATE SPRING |
| Парткод: | B044 4855 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AF02 2144 |
| Деталь: | Shaft-Pressure |
| Парткод: | AA14 0807 |
| Деталь: | Rear Upper Cover (NA) |
| Парткод: | B044 4925 |
| Деталь: | Rear Upper Cover (EU) |
| Парткод: | B044 4924 |
| Деталь: | COLLAR |
| Парткод: | B044 4857 |
| Деталь: | Decal - Misfeed |
| Парткод: | B044 4997 |
| Деталь: | Sheet - Exposure Glass |
| Парткод: | B044 4929 |
| Деталь: | Rear Lower Cover (NA) |
| Парткод: | B044 4927 |
| Деталь: | Rear Lower Cover (EU) |
| Парткод: | B044 4926 |
| Деталь: | Scale Decal |
| Парткод: | AA00 2256 |
| Деталь: | GUIDE PLATE |
| Парткод: | B044 4934 |
| Деталь: | PLATE SPRING |
| Парткод: | B044 4936 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AF02 2146 |
| Деталь: | PLATE SPRING |
| Парткод: | B044 4938 |
| Деталь: | PRESSURE SHAFT |
| Парткод: | AA14 5826 |
| Деталь: | COLLAR |
| Парткод: | B044 4937 |
| Деталь: | Lock Guide |
| Парткод: | B044 4939 |
| Деталь: | Contact Point Shaft |
| Парткод: | B044 4940 |
| Деталь: | BASE PLATE |
| Парткод: | B044 4930 |
| Деталь: | Exposure Glass Spacer |
| Парткод: | B044 4941 |
| Деталь: | Df Exposure Glass |
| Парткод: | AC01 3005 |
| Деталь: | Guide Plate-exposure Glass |
| Парткод: | B044 4935 |
| Деталь: | Front Lower Cover (NA) |
| Парткод: | B044 4923 |
| Деталь: | Front Lower Cover (EU) |
| Парткод: | B044 4922 |
| Деталь: | Front Upeer Cover (NA) |
| Парткод: | B044 4921 |
| Деталь: | Front Upper Cover (EU) |
| Парткод: | B044 4920 |
| Деталь: | Positioning Pin |
| Парткод: | B044 4964 |
| Деталь: | Shielding Plate |
| Парткод: | B044 4942 |
| Деталь: | White Standard Sheet - ADF |
| Парткод: | AC06 0004 |
| Деталь: | ADF Ground Wire |
| Парткод: | B044 4970 |
Коды ошибок
101
120
121
143
144
145
193
198
302
320
321
322
390
391
392
401
402
500
541
542
543
544
545
546
547
590
630
632
633
634
635
670
760
761
762
800
804
818
819
820
821
823
824
826
827
828
829
838
850
851
853
854
855
856
857
866
867
868
870
871
900
901
903
920
921
925
928
929
954
955
964
980
981
982
984
990
991
992
997
998
999
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 143 |
| Display: | Service Call 143:Error |
| Description: | Motor |
| Causes: | • SBU defective • IPU defective • BCU defective • Harness between the SBU and IPU defective • Harness between the BCU-IPU defective • Standard white plate not installed correctly, or is dirty • Scanner mirrors and/or lenses are dirty or installed incorrectly |
| Remedy: | DC pick motor, no encoder feedback - staging motor - replace the “Staging motor” on page 4-79. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 145 |
| Display: | SYSTEM HALT (*) 145 : MAIN CN6,9 CHK |
| Description: | Motor |
| Causes: | • Exposure lamp defective • Dirty white plate • Incorrect position or width of white plate scanning (SP4015) • BICU board defective • SBU board defective |
| Remedy: | DC motor excessive PWM autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 193 |
| Description: | Image transfer error The IPU board does not finish within 1 minute after the image data has been transferred to the controller board. |
| Causes: | • IPU board defective • Controller board defective • Video controller defective |
| Error code: | 198 |
| Description: | Memory address error The IPU board does not receive the memory address from the controller board. |
| Causes: | • Mismatched firmware between the SBCU board and controller board • Controller defective • SBCU defective • IPU board defective Note: Before you replace a board, update the firmware. This can repair the error. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 320 |
| Display: | Reset fuser 320: Fuser error |
| Description: | Same unit not detected upon power ON or opening cover. |
| Causes: | 1) Is error message displayed? 2) Is fuser unit set properly? 3) Does error reoccur? |
| Remedy: | Check if fuser is set properly. Reset fuser and turn ON power again. Replace fuser unit assembly. |
| Error code: | 321 |
| Display: | Turn power OFF and wait 321: MOTOR OVERHEAT |
| Description: | Printer cannot be used temporarily due to motor overheat. |
| Remedy: | Turn ON power after a while. |
| Error code: | 322 |
| Description: | Synchronization error The synchronization signal was not issued within 500 ms after the LD fired while the polygon motor was turning at the prescribed number of revolutions. |
| Causes: | • Laser synchronization board connectors or harness loose, disconnected, or damaged • Laser synchronization board defective or out of position • LD drive board defective |
| Remedy: | 1. Check the harness connection of the development HVPS. 2. Replace the development HVPS. 3. Replace the development unit. |
| Error code: | 390 |
| Display: | Check MP tray 390: Paper jam |
| Description: | Paper jam during paper feed from MT. |
| Causes: | Check for miss-fed paper around MT cassette. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace MT. |
| Error code: | 391 |
| Description: | TD sensor error: Auto adjust error During automatic adjustment of the TD sensor, output voltage was less than 1.8V, or more than 4.8V during TD sensor initial setting |
| Causes: | • TD sensor connector or harness loose, broken, defective • TD sensor defective • IOB defective • Toner supply defective (confirm that the toner seal strip has been removed from toner cartridge) |
| Remedy: | 1. Check the harness or harness connection. 2. Clean the surface of the quenching lamp glass. |
| Error code: | 392 |
| Description: | Development Bias Error The development bias feedback voltage was less than 0.3 V for longer than 200 ms while the PWM duty value was more than 5% (indicating a development bias leak). |
| Causes: | • Bias terminal damaged • High voltage cable damaged, defective • CGB power pack defective |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 500 |
| Description: | Transport/Fusing Motor Error |
| Causes: | The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the transport/fusing motor. Replace it if necessary. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 590 |
| Description: | Toner collection motor error The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on. |
| Causes: | • Motor lock due to obstruction • Motor driver board defective • Motor connection loose, defective • Toner collection motor sensor disconnected, sensor defective • Rotational transmission shaft (o6 x 30) missing |
| Error code: | 630 |
| Description: | CSS communication error A communication error occurred during communication with the CSS. |
| Causes: | • Communication line error |
| Remedy: | Logging only. |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 633 |
| Description: | Key/card counter device error 2 During communication with the device, the MCU received a break (Low) signal. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 760 |
| Description: | Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Punch HP sensor disconnected, defective • Punch motor disconnected or defective • Punch motor overload due to obstruction |
| Remedy: | 1. Check the connections and cables for the punch motor and HP sensor. 2. Check for blockages in the punch motor mechanism. 3. Replace the punch HP sensor and/or punch motor 4. Replace the finisher main board. |
| Error code: | 761 |
| Description: | Finisher folder plate motor error The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Remedy: | 1. Check the connections and cables for the folder plate motor and HP sensor. 2. Check for blockages in the folder plate motor mechanism. 3. Replace the folder plate HP sensor and/or folder plate motor 4. Replace the finisher main board. |
| Error code: | 762 |
| Description: | Front fold plate HP sensor error The state (on/off, off/on) of the front fold plate HP sensor in the fan fold unit did not change 1 sec. after the plate started to move. |
| Causes: | • Fold plate motor (F) harness connector loose, disconnected, broken • Front fold plate HP sensor harness connector loose, disconnected, broken • Fold plate motor (F) defective • Front fold plate HP sensor defective • Undetected paper is jamming the action of the motor or fold plate • Fan folder unit MCU defective |
| Error code: | 800 |
| Description: | Startup without video output end error (K) Video transfer to the engine is started, but the engine did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Error code: | 804 |
| Display: | SYSTEM HALT (*) 804 : (C)DMA ADDR |
| Description: | Startup without video input end (K) A video transmission was requested from the scanner, but the scanner did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 838 |
| Display: | SYSTEM HALT (*) 838 : FW/SV MDL |
| Description: | Self-diagnostic Error 10: Clock Generator A verify error occurred when setting data was read from the clock generator via the I2C bus. |
| Causes: | • Replace the controller board |
| Error code: | 850 |
| Description: | Net I/F error Duplicate IP addresses. Illegal IP address. Driver unstable and cannot be used on the network |
| Causes: | • IP address setting incorrect • NIB (PHY) board defective • Controller board defective |
| Remedy: | Turn the main switch off and on. |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 871 |
| Description: | FCU Flash ROM Error The address book written into the flash ROM mounted on the FCU is detected as defective. |
| Causes: | • Flash ROM device defective • Replace flash ROM on the MBU |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 903 |
| Display: | Power OFF/ON 903:Error |
| Description: | Paperport link driver error |
| Causes: | These errors indicate an unrecoverable system software error. |
| Remedy: | Replace the system board. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 928 |
| Display: | Power Off/on 928: Error |
| Description: | Failure in the Fuser Motor The Fuser Motor has stopped rotating. Applicable Status Code: Code 928: The Fuser Motor has failed. |
| Causes: | • Fuser Motor, PL2.1.9 • Motor Driver Board, PL2.1.10 • Engine Control Board, PL1.1.4 |
| Remedy: | 1 Test the Fuser Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Fuser Motor test. Does the motor operate? Complete. Replace the motor. If the error persists, go to Step 2. 2 Check for +24 V to the Fuser Motor. Is the +24 V across DCHEAT- 3 <=> ground? Go to Step 5. Go to Step 3. 3 Check Motor Driver Board POW24 connector for 24 V. 1. Disconnect POW24. Is the +24 V across POW24 pins 1 and 2? Replace the Motor Driver Board. Go to Step 4. 4 Check for 24 V at the LVPS 1. Disconnect CN2 on the LVPS. Is the +24 V across pins 1 and 2? Replace the POW24 Harness. Replace the LVPS. 5 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 929 |
| Display: | Power Off/on 929: Error |
| Description: | Failure in the Waste Toner Motor The Waste Toner Motor has stopped rotating. Applicable Status Code: Code 929: The Waste Toner Motor has failed. |
| Causes: | • Waste Toner Motor, PL7.1.3 • Motor Driver Board, PL2.1.10 • Engine Control Boar d, PL1.1.4 |
| Remedy: | 1 Test the Waste Toner Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Waste Toner Motor test. Does the motor operate? Complete. Replace the motor. If the error persists, go to Step 2. 2 Check for +24 V to the Waste Toner Motor. Is the +24 V across WTDC- 3 <=> ground? Go to Step 5. Go to Step 3. 3 Check Motor Driver Board POW24 connector for 24 V. 1. Disconnect POW24. Is the +24 V across POW24 pins 1 and 2? Replace the Motor Driver Board. Go to Step 4. 4 Check for 24 V at the LVPS 1. Disconnect CN2 on the LVPS. Is the +24 V across pins 1 and 2? Replace the POW24 Harness. Replace the LVPS. 5 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 954 |
| Description: | NVRAM CRC Failure |
| Causes: | • Firmware bug • IPU defective |
| Remedy: | Indicates the NVRAM experienced a CRC failure. Replace the interconnect board. |
| Error code: | 955 |
| Description: | Code CRC <loc> |
| Causes: | • Firmware bug • Hard disk unit defective • Controller defective • MCU defective • IPU defective |
| Remedy: | Replace the system board. Where <loc> = CRC Failure or ECC Failure on the system board. |
| Error code: | 964 |
| Description: | Emulation Error |
| Causes: | • Software defective |
| Remedy: | Indicates a failure within the Download Emulation which is programmed into the code overlay card. The specific error is as follows: 964 - Download Emulation CRC Failure. Checksum Failure. |
| Error code: | 980 |
| Display: | Contact the Service center. 980: Error |
| Description: | <device> Comm |
| Causes: | • See description below this table. |
| Remedy: | The engine is experiencing unreliable communications to the specified device. |
| Error code: | 981 |
| Display: | Service call 981: Error |
| Description: | <device> |
| Causes: | • Defective NVRAM • Loose connection between the BICU and the NVRAM • Incorrect installation of the NVRAM • Defective BICU |
| Remedy: | The engine protocol violation detected by the specified device. |
| Error code: | 982 |
| Display: | Service call 982: Error |
| Description: | <device> Comm |
| Causes: | • Localization setting not specified (The main power switch is turned on for the first time after the NVRAM is replaced.) • Incorrect localization setting • Defective NVRAM |
| Remedy: | Communications error detected by the specified device. |
| Error code: | 984 |
| Display: | Service call 984: Error. |
| Description: | <device> |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected |
| Remedy: | Invalid command parameter received by the specified device. Note: Service errors 980 thru 984 <device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
| Error code: | 999 |
| Display: | Service call 999: Error |
| Description: | Stapler Motor Error |
| Causes: | • Color registration (MUSIC) failure |
| Remedy: | 1 Are staples jammed in the stapler? Go to step 2. Go to step 3. 2 Clear the staple jam and run the staple test in diagnostic mode or run a staple job. Does the problem reoccur? Replace the staple cartridge and to go step 4. Problem solved. 3 Are the connectors CN5 on the stapler and PJ1 on the finisher control board securely connected? Go to step 5. Securely connect the connectors. 4 Did replacement of the stapler cartridge resolve the problem? Problem resolved. Replace the stapler. 5 Make sure the finisher set switch is activated. Measure for 5 V dc between pins 11 and 12 on stapler connector CN5. Is 5 V dc present? Replace the stapler. Replace the finisher control board. 6 Did replacement of the finisher control board correct the problem? Problem solved. Go to step 7. 7 Is there continuity on the stapler to finisher control board cable? Replace the power supply. Replace the cable. |
