Ricoh Aficio 2032
Рейтинг
Модули
DRIVE SECTION 3
OPERATION PANEL
DRIVE SECTION 4
TONER HOPPER UNIT
Paper Feed Section 1
OPTICS SECTION 2
PAPER REGISTRATION
Paper exit
OPTICS SECTION 3
DRIVE SECTION 2
Paper Feed Section 3
EXTERIOR 2
PAPER FEED SECTION 2
OPTICS SECTION 1
FRAME SECTION
PLATEN COVER
TRANSFER UNIT
Drive Section 1
ELECTRICAL SECTION 2
EXTERIOR 1
ELECTRICAL SECTION 1
FUSING UNIT 2
PAPER TRAY
FUSING UNIT 1
LASER UNIT
Детали DRIVE SECTION 3
| Деталь: | Support Bracket - Transport Clutch |
| Парткод: | B024 2605 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0792 |
| Деталь: | Timing Belt Tensioner |
| Парткод: | B024 2602 |
| Деталь: | TIMING PULLEY - 18T |
| Парткод: | AB03 0627 |
| Деталь: | Gear - 31Z/54Z |
| Парткод: | AB01 1199 |
| Деталь: | Timing Belt - S3M - 315 |
| Парткод: | AA04 3517 |
| Деталь: | Timing Pulley - 20T |
| Парткод: | AB03 0626 |
| Деталь: | Relay Harness - Density Sensor |
| Парткод: | B024 5236 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Harness - PCU Detector Board |
| Парткод: | B024 5203 |
| Деталь: | Right Drive Guard |
| Парткод: | A267 2596 |
| Деталь: | Magnetic clutch |
| Парткод: | B091 2617 |
| Деталь: | Magnetic clutch |
| Парткод: | B091 2616 |
| Деталь: | Feed Clutch Stopper |
| Парткод: | B024 2604 |
| Деталь: | Gear - 38Z |
| Парткод: | AB01 1200 |
| Деталь: | Positioning Guide - Bypass Feed |
| Парткод: | A267 2601 |
| Деталь: | Snap Ring |
| Парткод: | B091 2607 |
| Деталь: | Operation Panel Sub Unit (NA) |
| Парткод: | B093 7152 |
| Деталь: | Operation Panel Sub Unit (EU) |
| Парткод: | B093 7172 |
| Деталь: | Operation Panel Sub Unit (ASIA) |
| Парткод: | B093 7212 |
| Деталь: | Operation Panel Sub Unit (TWN) |
| Парткод: | B093 7192 |
| Деталь: | LOWER COVER |
| Парткод: | B027 1432 |
| Деталь: | Blank Cover - Fax |
| Парткод: | B027 1448 |
| Деталь: | LCDC Cover |
| Парткод: | B027 1490 |
| Деталь: | LCD - Hvga U14 B1 |
| Парткод: | B004 5216 |
| Деталь: | Upper Cover (NA/ASIA) |
| Парткод: | B027 7160 |
| Деталь: | Upper Cover (EU/TWN/CHN) |
| Парткод: | B027 1431 |
| Деталь: | Keytop - Try Print |
| Парткод: | B027 1435 |
| Деталь: | Keytop - Preheat |
| Парткод: | B027 1439 |
| Деталь: | Keytop - Confirm |
| Парткод: | B027 1440 |
| Деталь: | Keytop - Program |
| Парткод: | B027 1441 |
| Деталь: | Keytop - Counter |
| Парткод: | B027 1442 |
| Деталь: | Keytop - Start |
| Парткод: | B027 1433 |
| Деталь: | Keytop - Interrupt |
| Парткод: | B027 1438 |
| Деталь: | Keytop - Left Blank |
| Парткод: | B027 1449 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B027 1434 |
| Деталь: | Keytop - 10 key (NA) |
| Парткод: | B027 7161 |
| Деталь: | Keytop - 10key (ASIA) |
| Парткод: | B027 7214 |
| Деталь: | Keytop - 10key (EU/TWN/CHN) |
| Парткод: | B027 1437 |
| Деталь: | DIAL |
| Парткод: | B027 1444 |
| Деталь: | Keytop - Reset Switch |
| Парткод: | B027 7162 |
| Деталь: | Operation Panel Board - Left |
| Парткод: | B027 1450 |
| Деталь: | Operation Panel Board - Right |
| Парткод: | B027 1460 |
| Деталь: | Right Sheet - Operation Panel |
| Парткод: | B027 1482 |
| Деталь: | Left Sheet - Operation Panel |
| Парткод: | B027 1483 |
| Деталь: | Long Spacer - Touch Panel |
| Парткод: | B027 1484 |
| Деталь: | Short Spacer - Touch Panel |
| Парткод: | B027 1485 |
| Деталь: | Shadeing Plate |
| Парткод: | B027 1487 |
| Деталь: | LCDC Bracket |
| Парткод: | B027 1488 |
| Деталь: | LCDC (NA/ASIA) |
| Парткод: | B027 5041 |
| Деталь: | LCDC (EU/TWN/CHN) |
| Парткод: | B027 5042 |
| Деталь: | Gasket - 3x10 L95 |
| Парткод: | B027 1491 |
| Деталь: | Gasket - 3x10 L7.5 |
| Парткод: | B027 1492 |
| Деталь: | Sheet - Power Source Display (NA/ASIA) |
| Парткод: | B027 7164 |
| Деталь: | Sheet - Power Source Display (EU/TWN/CHN) |
| Парткод: | B027 7184 |
| Деталь: | TOUCH PANEL |
| Парткод: | A229 5216 |
| Деталь: | LED Display Sheet (NA/EU/ASIA) |
| Парткод: | B027 7163 |
| Деталь: | LED Display Sheet (TWN) |
| Парткод: | B027 7194 |
| Деталь: | LED Display Sheet (CHN) |
| Парткод: | B027 7204 |
| Деталь: | Keytop - Main Switch |
| Парткод: | B027 1436 |
| Деталь: | Front Left Lens |
| Парткод: | B027 1445 |
| Деталь: | Upper Left Sheet |
| Парткод: | B027 1495 |
| Деталь: | Power Pack - BCTD |
| Парткод: | B091 5730 |
| Деталь: | Receptacle - Change Roller |
| Парткод: | A267 3461 |
| Деталь: | Reseotacke - Transfer/Sprtion Unit |
| Парткод: | A267 3950 |
| Деталь: | Harness - Document Feeder |
| Парткод: | B027 5242 |
| Деталь: | Rear Guide Plate - Fusing Unit |
| Парткод: | B024 1076 |
| Деталь: | AC Harness - Fusing Unit (120V) |
| Парткод: | B027 7612 |
| Деталь: | AC Harness - Fusing Unit (230V) |
| Парткод: | B027 7632 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3301 |
| Деталь: | Harness - Bridge Unit |
| Парткод: | B027 5235 |
| Деталь: | Main Motor - DC 28W |
| Парткод: | B091 1129 |
| Деталь: | Main Motor - DC 28W (B097) |
| Парткод: | B0971129 |
| Деталь: | Harness - High Voltage Line |
| Парткод: | A267 5218 |
| Деталь: | Fly Wheel - 115.5mm |
| Парткод: | B024 1184 |
| Деталь: | Fly Wheel - 115.5mm (B097) |
| Парткод: | B024 1184 |
| Деталь: | Spacer - KGLS-12RF |
| Парткод: | G020 5871 |
| Деталь: | Power Pack Bracket |
| Парткод: | B024 5833 |
| Деталь: | IOB Upper Stand |
| Парткод: | B024 5839 |
| Деталь: | IOB Lower Stand |
| Парткод: | B024 5840 |
| Деталь: | TONER SUPPLY UNIT |
| Парткод: | B027 3501 |
| Деталь: | Cover - Toner Supply Unit |
| Парткод: | A267 3560 |
| Деталь: | Motor Spacer - Toner Bottle |
| Парткод: | B027 3620 |
| Деталь: | Toner Supply Motor - DC24V 2.6W |
| Парткод: | AX05 0170 |
| Деталь: | Motor Bracket - Toner Bottle |
| Парткод: | B027 7440 |
| Деталь: | Guide Plate - Toner Supply Unit |
| Парткод: | B024 1054 |
| Деталь: | Toner Slider |
| Парткод: | A184 3422 |
| Деталь: | Cam - Handle |
| Парткод: | A267 3605 |
| Деталь: | Chuck Shaft |
| Парткод: | A184 3421 |
| Деталь: | Chuck Spring - Tonner Bottle |
| Парткод: | A267 3556 |
| Деталь: | SLIDER ASSY |
| Парткод: | G020 3334 |
| Деталь: | Bottle Chuck |
| Парткод: | A184 3420 |
| Деталь: | Decal - High Temperature |
| Парткод: | AA00 0401 |
| Деталь: | T ray Heater Assy (120V) |
| Парткод: | A267 7350 |
| Деталь: | Tray Heater Assy (230V) |
| Парткод: | A267 7363 |
| Деталь: | Shoe - Right Rail |
| Парткод: | A267 2588 |
| Деталь: | Shoe - Supporter |
| Парткод: | A267 2589 |
| Деталь: | Rubber Pad - H5 |
| Парткод: | AH01 0009 |
| Деталь: | Front Grip Plate |
| Парткод: | A267 2564 |
| Деталь: | Rear Grip Plate |
| Парткод: | A267 2567 |
| Деталь: | Grip Bracket - Rear Left |
| Парткод: | B024 2576 |
| Деталь: | Grip Bracket - Rear Right |
| Парткод: | B024 2573 |
| Деталь: | Upper Guide - Vertical Transport |
| Парткод: | B024 2733 |
| Деталь: | Roller Clutch Bracket |
| Парткод: | B024 2677 |
| Деталь: | Spring Plate - Roller Clutch |
| Парткод: | A267 2680 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Stopper Band |
| Парткод: | A267 2740 |
| Деталь: | Lower Guide - Vertical Transport |
| Парткод: | B024 2732 |
| Деталь: | PULL OUT ROLLER - OPTION TRAY |
| Парткод: | AF02 2118 |
| Деталь: | BUSHING - VERTICAL TRANSPORT |
| Парткод: | AA08 0249 |
| Деталь: | Spring - Vertical Transport |
| Парткод: | AA06 3334 |
| Деталь: | Vertical Shield - 2.5x7.363 |
| Парткод: | AA15 3437 |
| Деталь: | Vertical Transport Cover Assy |
| Парткод: | B024 2728 |
| Деталь: | Vertical Transport Cover |
| Парткод: | B024 2738 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0014 |
| Деталь: | Decal - Vertical Transport Cover |
| Парткод: | B024 2737 |
| Деталь: | Vertical Transport Guide |
| Парткод: | A267 2736 |
| Деталь: | Lower Paper Guide Plate |
| Парткод: | A267 2724 |
| Деталь: | Harness - Scanner (NA) |
| Парткод: | B027 5226 |
| Деталь: | Harness - Scanner (EU/ASIA) |
| Парткод: | B027 5230 |
| Деталь: | Original Sensor - H2-66 (120V) |
| Парткод: | A250 1761 |
| Деталь: | Original Sensor - H2-66 (230V) |
| Парткод: | A250 1761 |
| Деталь: | Harness - SBU |
| Парткод: | B027 5225 |
| Деталь: | 1st Mirror Holder |
| Парткод: | A1931767 |
| Деталь: | 1st Scanner |
| Парткод: | B027 1752 |
| Деталь: | Wire Clamp |
| Парткод: | A1931766 |
| Деталь: | Xenon Lamp - 8.5MM |
| Парткод: | AX50 0077 |
| Деталь: | Lens Holder |
| Парткод: | B027 1673 |
| Деталь: | 1st Mirror |
| Парткод: | A2501784 |
| Деталь: | Clamp - Rear Wire |
| Парткод: | A1931769 |
| Деталь: | Harness Guide - Exposure Lamp |
| Парткод: | A267 1758 |
| Деталь: | Flexible Board |
| Парткод: | B027 5227 |
| Деталь: | Flexible Board Bracket |
| Парткод: | B027 1808 |
| Деталь: | Xenon Lamp Stabilizer |
| Парткод: | AZ50 0059 |
| Деталь: | Lens Block Holder |
| Парткод: | B027 1811 |
| Деталь: | Scanner base |
| Парткод: | B027 1802 |
| Деталь: | Grounding Plate - Regist Roller |
| Парткод: | A267 2695 |
| Деталь: | PCU Guide Plate |
| Парткод: | B0931051 |
| Деталь: | PCU Seal |
| Парткод: | A267 1059 |
| Деталь: | Quenching Lamp |
| Парткод: | B093 3452 |
| Деталь: | Bushing - Registration Roller |
| Парткод: | A267 2674 |
| Деталь: | Bushing - Paper Feed Roller |
| Парткод: | H521 3356 |
| Деталь: | Snap Ring M4 |
| Парткод: | G024 3344 |
| Деталь: | Relay Harness - Registration Sensor |
| Парткод: | B024 5237 |
| Деталь: | Upper Entrance Guide Plate |
| Парткод: | A267 2721 |
| Деталь: | Cushion - Link |
| Парткод: | AA16 1143 |
| Деталь: | Sub Guide Plate - Upper Entrance |
| Парткод: | A267 2722 |
| Деталь: | Left Guide Plate Assy |
| Парткод: | B024 2691 |
| Деталь: | Registration Roller Cleaner |
| Парткод: | A267 2700 |
| Деталь: | Registration Roller |
| Парткод: | AF02 0559 |
| Деталь: | Registration Roller (B097) |
| Парткод: | AF02 0520 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Upper Roller Guide |
| Парткод: | A267 2665 |
| Деталь: | Pegistration Sensor |
| Парткод: | AW01 0057 |
| Деталь: | Registration Sensor Bracket |
| Парткод: | B024 2698 |
| Деталь: | Cleaner:Registration:No.2:Assy |
| Парткод: | B027 2711 |
| Деталь: | CLIP |
| Парткод: | B027 2714 |
| Деталь: | Roller - Lever |
| Парткод: | A267 3958 |
| Деталь: | Sensor Cover - Paper Feed |
| Парткод: | A267 4489 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | AA12 0094 |
| Деталь: | Shaft - Paper Overflow |
| Парткод: | A267 4479 |
| Деталь: | Outer Stopper |
| Парткод: | A267 4487 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | A267 4483 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0567 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0566 |
| Деталь: | STOPPER |
| Парткод: | A267 4486 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | A267 4474 |
| Деталь: | Feeler - Paper Overflow |
| Парткод: | A267 4478 |
| Деталь: | EXIT ROLLER |
| Парткод: | AF02 0475 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1404 |
| Деталь: | Guide Plate - Paper Exit |
| Парткод: | A267 4454 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0014 |
| Деталь: | Stopper - Right Upper Cover |
| Парткод: | A267 1349 |
| Деталь: | Guide Plate Cover - Paper Exit |
| Парткод: | B027 1346 |
| Деталь: | Relay Harness - Paper Exit Section |
| Парткод: | A267 5207 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0086 |
| Деталь: | Feeler - Paper Feed Sensor |
| Парткод: | A267 4476 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 2112 |
| Деталь: | Exit Stay |
| Парткод: | B024 4452 |
| Деталь: | Front Pulley - Wire Drive |
| Парткод: | AB03 2066 |
| Деталь: | Scanner Drive Wire |
| Парткод: | AA05 0111 |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | A232 3553 |
| Деталь: | Tension Bracket |
| Парткод: | B027 1837 |
| Деталь: | TENSION SPRING |
| Парткод: | A1931783 |
| Деталь: | Front Left Bracket - Idler |
| Парткод: | B024 1841 |
| Деталь: | Slide Rail - 2 |
| Парткод: | A267 1817 |
| Деталь: | Slide Rail |
| Парткод: | A193 1816 |
| Деталь: | 2nd Scanner Housing |
| Парткод: | B027 1767 |
| Деталь: | 3rd Mirror |
| Парткод: | AC03 0144 |
| Деталь: | MIRROR HOLDER |
| Парткод: | A267 1777 |
| Деталь: | Scanner Drive Shaft |
| Парткод: | B027 1825 |
| Деталь: | Anticondensation Heater - 120V |
| Парткод: | A267 8465 |
| Деталь: | Anticondensation Heater - 230V |
| Парткод: | A267 8466 |
| Деталь: | Timing Belt - ST1.5 249MM |
| Парткод: | AA04 3572 |
| Деталь: | Guide - FPC |
| Парткод: | A267 1776 |
| Деталь: | Guide - Flexible Board |
| Парткод: | A267 1816 |
| Деталь: | Insulating Sheet - Side Plate |
| Парткод: | A267 1819 |
| Деталь: | Rear Left Bracket - Idler |
| Парткод: | B024 1845 |
| Деталь: | Rear Pulley - Wire Drive |
| Парткод: | AB03 2067 |
| Деталь: | Tension Spring - 7.5N |
| Парткод: | AA06 0878 |
| Деталь: | Scanner Motor -DC4.88V 7.8W |
| Парткод: | B027 1690 |
| Деталь: | Drive Guard |
| Парткод: | B027 1812 |
| Деталь: | Timing Pulley - 81 |
| Парткод: | AB03 0709 |
| Деталь: | Heater - 9W (120V) |
| Парткод: | A250 1821 |
| Деталь: | Heater - 9W (230V) |
| Парткод: | A2501822 |
| Деталь: | Heater Harness Cover |
| Парткод: | A267 1830 |
| Деталь: | Harness - By-pass/Duplex |
| Парткод: | B024 5244 |
| Деталь: | Connector Bracket - By-pass Feed |
| Парткод: | B024 5826 |
| Деталь: | Gear - 44Z |
| Парткод: | AB01 4050 |
| Деталь: | Fusing Drive Cover |
| Парткод: | B024 1162 |
| Деталь: | Gear - 27Z |
| Парткод: | AB01 1204 |
| Деталь: | Fusing Swivel Bracket |
| Парткод: | B0271170 |
| Деталь: | Gear - 30Z |
| Парткод: | AB01 1203 |
| Деталь: | Fusing Drive Bracket |
| Парткод: | B024 1159 |
| Деталь: | Magnetic clutch |
| Парткод: | AX20 0165 |
| Деталь: | PCU Detector Board |
| Парткод: | B027 5156 |
| Деталь: | DC Solenoid Lever |
| Парткод: | B027 1164 |
| Деталь: | Harness Bracket |
| Парткод: | B024 5824 |
| Деталь: | Connector Bracket - Paper Feed |
| Парткод: | B024 1183 |
| Деталь: | Connector Bracket - Paper Feed (B097) |
| Парткод: | G062 1183 |
| Деталь: | Tension Bracket |
| Парткод: | B024 1115 |
| Деталь: | Timing Pulley - 31T/36T |
| Парткод: | AB03 3091 |
| Деталь: | Timing Belt - S3M - 342 |
| Парткод: | AA04 3516 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 7504 |
| Деталь: | Gear - 24Z (B097) |
| Парткод: | AB01 7625 |
| Деталь: | Gear - 35Z/28Z |
| Парткод: | AB01 7503 |
| Деталь: | Timing Belt - S3M - 225 |
| Парткод: | AA04 3515 |
| Деталь: | Timing Pulley - 27T/48T |
| Парткод: | AB03 3092 |
| Деталь: | Timing Belt - S3M - 420 |
| Парткод: | AA04 3514 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0792 |
| Деталь: | Shoulder Screw - M3x2.5 |
| Парткод: | G020 5829 |
| Деталь: | Bracket - Paper End Sensor |
| Парткод: | B024 2805 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0075 |
| Деталь: | Relay Harness - Paper End Sensor |
| Парткод: | B024 5215 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A267 2751 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | A267 2803 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | A267 2754 |
| Деталь: | Vertical Sensor Bracket |
| Парткод: | B024 2660 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0111 |
| Деталь: | Transport Roller |
| Парткод: | AF02 0472 |
| Деталь: | Transport Roller (B097) |
| Парткод: | AF02 0522 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0252 |
| Деталь: | Bracket - Friction Pad Guide |
| Парткод: | B024 2842 |
| Деталь: | Paper Size Sensor Bracket 2 |
| Парткод: | B027 2882 |
| Деталь: | Push Switch - Paper Size |
| Парткод: | G020 2620 |
| Деталь: | Stopper Paper Feed Roller |
| Парткод: | B093 2935 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Guide Plate Paper Feed Roller 2 Assy |
| Парткод: | B093 2808 |
| Деталь: | Rear Left Cover - Paper Feed |
| Парткод: | B0931304 |
| Деталь: | Rear Left Cover - Paper Feed (EU) |
| Парткод: | B093 7021 |
| Деталь: | Decal - Keytop Cover (GES) |
| Парткод: | A153 6409 |
| Деталь: | Decal - Keytop Cover (REX) |
| Парткод: | C225 2866 |
| Деталь: | Decal - Keytop Cover (NSA) |
| Парткод: | C225 2867 |
| Деталь: | LEFT COVER |
| Парткод: | B024 1281 |
| Деталь: | Left rear cover |
| Парткод: | B093 1282 |
| Деталь: | Left Rear Cover (EU) |
| Парткод: | B093 7018 |
| Деталь: | LEFT UPPER COVER |
| Парткод: | B024 1280 |
| Деталь: | Upper Rear Cover - Scanner |
| Парткод: | B024 1251 |
| Деталь: | Cap - 38x77 |
| Парткод: | B024 1365 |
| Деталь: | Rivet - M7 |
| Парткод: | B0391364 |
| Деталь: | Cap - Paper Feed Table |
| Парткод: | B024 1374 |
| Деталь: | Cap - Duplex Connector |
| Парткод: | B024 1371 |
| Деталь: | Right Rear Cover - Paper Feed |
| Парткод: | B024 2717 |
| Деталь: | Cap Stay |
| Парткод: | B024 2710 |
| Деталь: | Cap - By-pass Feed |
| Парткод: | B024 2708 |
| Деталь: | Hexagonal Set Screw - M3x8 |
| Парткод: | A267 2713 |
| Деталь: | Operation Panel Sub Unit (NA) |
| Парткод: | B093 7152 |
| Деталь: | Operation Panel Sub Unit (EU) |
| Парткод: | B093 7172 |
| Деталь: | Operation Panel Sub Unit (ASIA) |
| Парткод: | B093 7212 |
| Деталь: | Operation Panel Sub Unit (TWN) |
| Парткод: | B093 7192 |
| Деталь: | Right Middle Cover - Paper Feed |
| Парткод: | B024 2727 |
| Деталь: | Right Front Cover - Paper Feed |
| Парткод: | B024 2716 |
| Деталь: | Lower Cover - Paper Exit |
| Парткод: | B024 1345 |
| Деталь: | Guide Mylar |
| Парткод: | A267 2709 |
| Деталь: | Right Cover Shield - 3x5x85 |
| Парткод: | AA15 3435 |
| Деталь: | Right Cover Shield - 3x10x363 |
| Парткод: | AA15 3434 |
| Деталь: | Right Cover Shield - 3x5x70 |
| Парткод: | AA15 3436 |
| Деталь: | Right middle cover |
| Парткод: | B024 2705 |
| Деталь: | Spring - Vertical Transport |
| Парткод: | AA06 3334 |
| Деталь: | BUSHING - VERTICAL TRANSPORT |
| Парткод: | AA08 0249 |
| Деталь: | Driven Roller - Vertical Transport |
| Парткод: | A267 2715 |
| Деталь: | Cap - Duplex |
| Парткод: | B024 1370 |
| Деталь: | RIGHT COVER |
| Парткод: | B024 1270 |
| Деталь: | Rear Cover - Paper Feed |
| Парткод: | B024 1291 |
| Деталь: | RIVET |
| Парткод: | B0391363 |
| Деталь: | Cap - Dehumidifier Heater |
| Парткод: | B0241375 |
| Деталь: | Right scanner cover |
| Парткод: | B024 1252 |
| Деталь: | REAR COVER |
| Парткод: | B024 1290 |
| Деталь: | Left scanner cover |
| Парткод: | B024 1250 |
| Деталь: | Screw - M4x5 |
| Парткод: | A267 2945 |
| Деталь: | Guide Plate Bracket - 2 |
| Парткод: | B024 2587 |
| Деталь: | Cushion - Link |
| Парткод: | AA16 1143 |
| Деталь: | Bracket - Paper End Sensor |
| Парткод: | B024 2805 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0075 |
| Деталь: | Relay Harness - Paper End Sensor |
| Парткод: | B024 5215 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A267 2751 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | A267 2803 |
| Деталь: | Cushion - Guide Plate |
| Парткод: | A267 2813 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | A267 2754 |
| Деталь: | Sensor bracket |
| Парткод: | B024 2663 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0111 |
| Деталь: | C Ring - Paper Feed Roller |
| Парткод: | H521 3355 |
| Деталь: | Bushing - Paper Feed Roller |
| Парткод: | H521 3356 |
| Деталь: | Roller Guide Bracket - 2 |
| Парткод: | B024 2577 |
| Деталь: | Upper Roller Guide |
| Парткод: | A267 2665 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 0500 |
| Деталь: | Driven Roller (B097) |
| Парткод: | AF02 0523 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0252 |
| Деталь: | Pressure Release Guide |
| Парткод: | B024 2828 |
| Деталь: | Bracket - Paper Size Sensor |
| Парткод: | B024 2873 |
| Деталь: | Push Switch - Paper Size |
| Парткод: | G020 2620 |
| Деталь: | Lock Lever - Feed Roller |
| Парткод: | A267 2792 |
| Деталь: | Tension Spring - Lock Lever |
| Парткод: | A267 2787 |
| Деталь: | Bushing - Motor Shaft |
| Парткод: | A267 2847 |
| Деталь: | Lock Lever Shaft - Feed Roller |
| Парткод: | A267 2785 |
| Деталь: | Bushing - Roller Guide |
| Парткод: | A267 2666 |
| Деталь: | Upper Guide Plate - Feed Roller |
| Парткод: | B024 2800 |
| Деталь: | Roller Clutch-vertical Trans Port |
| Парткод: | B027 2681 |
| Деталь: | Torsion Spring - Lock Lever |
| Парткод: | A267 2788 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 54 421 924 |
| Деталь: | Scanner Frame |
| Парткод: | A267 1813 |
| Деталь: | Bracket - Scale |
| Парткод: | B027 1742 |
| Деталь: | STEPPED SCREW |
| Парткод: | A1931759 |
| Деталь: | Rear Scale |
| Парткод: | B024 1701 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0086 |
| Деталь: | Sheet - Photointerrupter |
| Парткод: | A267 1820 |
| Деталь: | Hinge Bracket - Platen Cover |
| Парткод: | A267 1814 |
| Деталь: | Inner cover |
| Парткод: | B027 1815 |
| Деталь: | Exposure Glass |
| Парткод: | A2501752 |
| Деталь: | Left Scale |
| Парткод: | B386 7105 |
| Деталь: | Harness - Home Position Sensor |
| Парткод: | B027 5208 |
| Деталь: | SAFETY SWITCH |
| Парткод: | B093 5808 |
| Деталь: | Reft Rear Bracket |
| Парткод: | B024 1085 |
| Деталь: | Guide Plate - Exhaust Duct |
| Парткод: | B024 1106 |
| Деталь: | Exaust Fan Motor - DC 2.88W |
| Парткод: | A267 1105 |
| Деталь: | Duct - Fam Motor |
| Парткод: | A267 1102 |
| Деталь: | Grounding Plate - Upper Rear |
| Парткод: | A267 1089 |
| Деталь: | Grounding Plate - Lower Right |
| Парткод: | A267 1090 |
| Деталь: | PCU Bracket |
| Парткод: | B027 1091 |
| Деталь: | Hinge - Front Door |
| Парткод: | B024 1088 |
| Деталь: | Positioning Bracket - Laser Unit |
| Парткод: | A267 1930 |
| Деталь: | Mechanical Counter |
| Парткод: | AX31 0038 |
| Деталь: | Lever - Door Switch |
| Парткод: | A267 5815 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | A267 5820 |
| Деталь: | Harness - Front Door Switch |
| Парткод: | B027 5204 |
| Деталь: | Door Switch Bracket |
| Парткод: | B024 5812 |
| Деталь: | Micro Switch Bracket |
| Парткод: | B024 5813 |
| Деталь: | Tension Spring - Door Switch |
| Парткод: | A267 5821 |
| Деталь: | Arm - Scanner |
| Парткод: | B0931084 |
| Деталь: | Support Bracket - Left Rear |
| Парткод: | B024 1083 |
| Деталь: | Frame Right Rear |
| Парткод: | B024 1079 |
| Деталь: | Scanner Stay - Lower Right |
| Парткод: | A267 1080 |
| Деталь: | Front Right Frame |
| Парткод: | B024 1078 |
| Деталь: | Fan - MM80 - Polygon Mirror Motor (B097) |
| Парткод: | G062 1104 |
| Деталь: | Duct - Fan Polygon Mirror Motor (B097) |
| Парткод: | G062 1107 |
| Деталь: | Platen Cover Sheet |
| Парткод: | 54 482 804 |
| Деталь: | Platen Cover Pad |
| Парткод: | AA16 2067 |
| Деталь: | Flex Hinge - Platen Cover |
| Парткод: | A0531957 |
| Деталь: | Front Platen Cover |
| Парткод: | B4061387 |
| Деталь: | ORIGINAL HOLDER |
| Парткод: | B406 1397 |
| Деталь: | Rear Platen Cover |
| Парткод: | B406 1392 |
| Деталь: | Platen Cover Hinge Assembly |
| Парткод: | A1931248 |
| Деталь: | Feeler - Platen Cover |
| Парткод: | B406 1384 |
| Деталь: | Screw - M4 |
| Парткод: | A548 6121 |
| Деталь: | Bracket - Platen Cover |
| Парткод: | B4061383 |
| Деталь: | Shutter Lever |
| Парткод: | B024 3931 |
| Деталь: | Pressure Spring Rear |
| Парткод: | AA06 3395 |
| Деталь: | Transfer/Separation Unit |
| Парткод: | A267 3831 |
| Деталь: | Spring Plate - Band Stopper |
| Парткод: | A232 3962 |
| Деталь: | Band - Vertical Transport Cover |
| Парткод: | A267 3941 |
| Деталь: | Transfer/Separation Unit Cover |
| Парткод: | B027 3821 |
| Деталь: | RIGHT COVER |
| Парткод: | B024 3857 |
| Деталь: | Decal - Right Cover |
| Парткод: | B024 3858 |
| Деталь: | ID SENSOR |
| Парткод: | A267 9007 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3599 |
| Деталь: | Pressure Spring Front |
| Парткод: | AA06 3394 |
| Деталь: | Front Bushing - Transfer Roller |
| Парткод: | AA08 0256 |
| Деталь: | Bushing - Driven Roller |
| Парткод: | A267 2685 |
| Деталь: | Right Guide Plate |
| Парткод: | B024 2711 |
| Деталь: | Cleaner - Regist Driven Roller |
| Парткод: | A267 2712 |
| Деталь: | Grounding Terminal |
| Парткод: | A267 3921 |
| Деталь: | Rear Bushing - Transfer Roller |
| Парткод: | AA08 0250 |
| Деталь: | Transfer/Separation Lever |
| Парткод: | B024 3871 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3598 |
| Деталь: | Terminal - Separation |
| Парткод: | A267 3862 |
| Деталь: | Terminal - Transfer Roller |
| Парткод: | A267 3861 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3607 |
| Деталь: | Guide Mylar |
| Парткод: | A267 2744 |
| Деталь: | Rear Discharge Sheet |
| Парткод: | AA15 0709 |
| Деталь: | Registration Driven Roller |
| Парткод: | AF02 1066 |
| Деталь: | Front Discharge Sheet |
| Парткод: | AA15 0708 |
| Деталь: | Cover - ID Sensor |
| Парткод: | A267 3905 |
| Деталь: | DC Motor - 1.92W |
| Парткод: | AX04 0119 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0075 |
| Деталь: | Bushing - 8x16x7 |
| Парткод: | AA08 2070 |
| Деталь: | Lift Sensor Bracket |
| Парткод: | B024 2773 |
| Деталь: | Rear Right Cover - Positioning Pin |
| Парткод: | B024 2592 |
| Деталь: | Tray Lift Assembly |
| Парткод: | B031 2780 |
| Деталь: | Pressure Lever Stopper |
| Парткод: | B024 2765 |
| Деталь: | Tension Spring - Stopper |
| Парткод: | A267 2766 |
| Деталь: | Rear Left Cover - Positioning Pin |
| Парткод: | B024 2593 |
| Деталь: | Bracket - Power Supply Cord |
| Парткод: | B027 5831 |
| Деталь: | Tray Holder Bracket |
| Парткод: | B024 2908 |
| Деталь: | Tray Holder |
| Парткод: | G697 1082 |
| Деталь: | Bracket - Heater Harness |
| Парткод: | B024 2916 |
| Деталь: | Holder - Spring |
| Парткод: | A267 2846 |
| Деталь: | Compression Spring - Return |
| Парткод: | A267 2844 |
| Деталь: | Bushing - DC Motor Shaft |
| Парткод: | A267 2845 |
| Деталь: | Bracket DC Motor Toner Bottle Z EXP |
| Парткод: | B090 7440 |
| Деталь: | Shaft - DC Motor |
| Парткод: | A267 2840 |
| Деталь: | Pin - M6 |
| Парткод: | A267 2836 |
| Деталь: | Spacer - M6 |
| Парткод: | AA13 2208 |
| Деталь: | Tension Spring - Main |
| Парткод: | A267 2771 |
| Деталь: | Tension Spring - Sub |
| Парткод: | A267 2772 |
| Деталь: | Torsion Spring - Joint |
| Парткод: | A267 2767 |
| Деталь: | Actuator - Paper Height Sensor |
| Парткод: | B031 2777 |
| Деталь: | Vibrating Plate |
| Парткод: | A267 2770 |
| Деталь: | Main Bracket - Pressure Lever |
| Парткод: | B024 2815 |
| Деталь: | Spring Guard |
| Парткод: | B024 2595 |
| Деталь: | Harness Cover - Paper Feed |
| Парткод: | B024 2839 |
| Деталь: | Upper Bracket - Paper Lift Motor |
| Парткод: | B024 2837 |
| Деталь: | Bushing - Motor Shaft |
| Парткод: | A267 2847 |
| Деталь: | Lever - DC Motor |
| Парткод: | B031 2776 |
| Деталь: | Holder - Pressure Spring |
| Парткод: | B024 2848 |
| Деталь: | Shutter - Photointerruptor |
| Парткод: | A267 2849 |
| Деталь: | Sub Pressure Lever |
| Парткод: | A267 2794 |
| Деталь: | Pressure Lever Bracket |
| Парткод: | B024 2781 |
| Деталь: | Shadeing Plate |
| Парткод: | B027 5815 |
| Деталь: | Shadeing Plate - IPU |
| Парткод: | B027 5817 |
| Деталь: | GRIP |
| Парткод: | B027 5816 |
| Деталь: | NVRAM - ZERO Counter |
| Парткод: | B022 9590 |
| Деталь: | Contoroller Board Sub Assy (B089) |
| Парткод: | B089 5301 |
| Деталь: | Contoroller Board Sub Assy (B093) |
| Парткод: | B089 5302 |
| Деталь: | Contoroller Board Sub Assy (B097) |
| Парткод: | B089 5303 |
| Деталь: | PANEL |
| Парткод: | B093 5814 |
| Деталь: | Upper Stand |
| Парткод: | B027 5811 |
| Деталь: | IPU Bracket |
| Парткод: | B027 5820 |
| Деталь: | Lower Stand |
| Парткод: | B027 5812 |
| Деталь: | GROUNDING PLATE |
| Парткод: | A267 7586 |
| Деталь: | IPU Board |
| Парткод: | B031 5115 |
| Деталь: | Harness - Laser Diode Control |
| Парткод: | B027 5223 |
| Деталь: | Harness - IPU (120V) |
| Парткод: | B027 5210 |
| Деталь: | Harness - IPU (230V) |
| Парткод: | B027 7633 |
| Деталь: | Bracket: Protect: CTL |
| Парткод: | B0931095 |
| Деталь: | Energy Decal |
| Парткод: | GA00 3035 |
| Деталь: | Hinge - Front Cover |
| Парткод: | G020 1332 |
| Деталь: | MAGNET CATCH |
| Парткод: | B024 1264 |
| Деталь: | PANEL:EMBLEM:EXP:2022 |
| Парткод: | B089 7060 |
| Деталь: | PANEL:EMBLEM:SVN:4022 |
| Парткод: | B089 7062 |
| Деталь: | PANEL:EMBLEM:GES:622:NA |
| Парткод: | B089 7063 |
| Деталь: | PANEL:EMBLEM:LAN:LD122 |
| Парткод: | B089 7064 |
| Деталь: | PANEL:EMBLEM:GES:622 |
| Парткод: | B089 7065 |
| Деталь: | PANEL:EMBLEM:NSA:622 |
| Парткод: | B089 7066 |
| Деталь: | PANEL:EMBLEM:REX:622 |
| Парткод: | B089 7067 |
| Деталь: | PANEL:EMBLEM:EXP:2027 |
| Парткод: | B093 7060 |
| Деталь: | PANEL:EMBLEM:SVN:4027 |
| Парткод: | B093 7062 |
| Деталь: | PANEL:EMBLEM:GES:627:NA |
| Парткод: | B093 7063 |
| Деталь: | PANEL:EMBLEM:LAN:LD127 |
| Парткод: | B093 7064 |
| Деталь: | PANEL:EMBLEM:GES:627 |
| Парткод: | B093 7065 |
| Деталь: | PANEL:EMBLEM:NSA:627 |
| Парткод: | B093 7066 |
| Деталь: | PANEL:EMBLEM:REX:62 |
| Парткод: | B093 7067 |
| Деталь: | PANEL:EMBLEM:EXP:2032 |
| Парткод: | B097 7060 |
| Деталь: | PANEL:EMBLEM:LAN:LD132 |
| Парткод: | B097 7064 |
| Деталь: | PANEL:EMBLEM:GES:632 |
| Парткод: | B097 7065 |
| Деталь: | PANEL:EMBLEM:NSA:632 |
| Парткод: | B097 7066 |
| Деталь: | PANEL:EMBLEM:REX:632 |
| Парткод: | B097 7067 |
| Деталь: | Cover - Main Switch |
| Парткод: | A291 1302 |
| Деталь: | Front Door (NA) |
| Парткод: | B027 7051 |
| Деталь: | Front Cover (EU/ASIA) |
| Парткод: | B027 7071 |
| Деталь: | Left Cover - Paper Exit |
| Парткод: | B024 1341 |
| Деталь: | Paper End Fence |
| Парткод: | B024 1343 |
| Деталь: | PAPER EXIT TRAY |
| Парткод: | B024 1348 |
| Деталь: | Left Cover - Paper Exit Assy |
| Парткод: | B024 1340 |
| Деталь: | Front Small Cover |
| Парткод: | B024 1388 |
| Деталь: | Upper Right Cover - Front |
| Парткод: | B024 1320 |
| Деталь: | COVER FRONT |
| Парткод: | B0931324 |
| Деталь: | Front Cover (EU) |
| Парткод: | B093 7024 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0004 |
| Деталь: | Operation Instructions Sheet |
| Парткод: | B027 1268 |
| Деталь: | Shield Duct |
| Парткод: | A267 1342 |
| Деталь: | Upper Paper Exit Cover |
| Парткод: | B024 1306 |
| Деталь: | Cap - LED |
| Парткод: | A267 1325 |
| Деталь: | Scanner Holder |
| Парткод: | B024 1099 |
| Деталь: | Decal - Postscript |
| Парткод: | AA00 1345 |
| Деталь: | Decal - Main Switch (CHN) |
| Парткод: | B027 1390 |
| Деталь: | Cover:Shield Glass:P |
| Парткод: | G062 1264 |
| Деталь: | Harness - Paper Feed 2 |
| Парткод: | B024 5234 |
| Деталь: | Harness - Paper Feed 1 |
| Парткод: | B024 5233 |
| Деталь: | Harness - Paper Feed Motor |
| Парткод: | B024 5230 |
| Деталь: | Harness - Paper Size Sensor |
| Парткод: | B027 5231 |
| Деталь: | Harness - Registration Sensor |
| Парткод: | B024 5201 |
| Деталь: | Harness - Quenching Lamp |
| Парткод: | B024 5205 |
| Деталь: | Harness - Main Motor |
| Парткод: | B027 5202 |
| Деталь: | Harness - Paper Exit |
| Парткод: | B027 5206 |
| Деталь: | Harness - Home Position Sensor |
| Парткод: | B027 5208 |
| Деталь: | Harness - Scanner Motor |
| Парткод: | B027 5200 |
| Деталь: | Harness - Scanner Motor (LAN) |
| Парткод: | B027 7637 |
| Деталь: | Main Switch |
| Парткод: | B024 5822 |
| Деталь: | Power Supply Unit -197W AC100-120V |
| Парткод: | B093 5720 |
| Деталь: | Power Supply Unit -197W AC220-240V |
| Парткод: | B093 5722 |
| Деталь: | Choke Coil - Ritl-9902 (230V w/o CHN) |
| Парткод: | N607 4541 |
| Деталь: | Harness - Anticondensation Heater |
| Парткод: | A267 7635 |
| Деталь: | Power Supply Cord - 120V |
| Парткод: | A267 7611 |
| Деталь: | Power Supply Cord - 230V |
| Парткод: | A267 7631 |
| Деталь: | Harness - Power Supply Unit |
| Парткод: | B027 5212 |
| Деталь: | IOB Bracket |
| Парткод: | B024 5838 |
| Деталь: | Harness - Front Door Switch |
| Парткод: | B027 5204 |
| Деталь: | Harness - Paper Feed |
| Парткод: | B024 5209 |
| Деталь: | SBCU Board |
| Парткод: | B093 5050 |
| Деталь: | Harness - PP |
| Парткод: | B024 5217 |
| Деталь: | Main Switch Bracket |
| Парткод: | B024 5823 |
| Деталь: | Front Terminal Plate - Thermostat |
| Парткод: | B027 4091 |
| Деталь: | Thermostat Housing |
| Парткод: | B027 4094 |
| Деталь: | Thermostat Assy |
| Парткод: | B027 4095 |
| Деталь: | Grip - Fusing Pressure |
| Парткод: | A267 4112 |
| Деталь: | Front Lever - Pressure Roller |
| Парткод: | B024 4113 |
| Деталь: | Front Side Plate |
| Парткод: | B031 4121 |
| Деталь: | Shaft - Fusing Pressure |
| Парткод: | A267 4111 |
| Деталь: | Rear Lever - Pressure Roller |
| Парткод: | B024 4115 |
| Деталь: | Rear Terminal Plate - Thermostat |
| Парткод: | B027 4093 |
| Деталь: | Fusing Cleaning Roller |
| Парткод: | AE04 2029 |
| Деталь: | Roller Busing |
| Парткод: | AA08 2073 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 3570 |
| Деталь: | Drive Release Lever |
| Парткод: | B024 4083 |
| Деталь: | Drive Release Link Plate |
| Парткод: | B024 4082 |
| Деталь: | Tension Spring - Pressure Lever |
| Парткод: | A267 4081 |
| Деталь: | Fusing Ground Plate - Entrance |
| Парткод: | A267 4086 |
| Деталь: | Thermistor - Rear |
| Парткод: | AW10 0053 |
| Деталь: | Thermistor Holder |
| Парткод: | B024 4099 |
| Деталь: | Spacer - Safety Switch |
| Парткод: | A267 4076 |
| Деталь: | Spur |
| Парткод: | A232 2374 |
| Деталь: | Thermostat Cover |
| Парткод: | B027 4078 |
| Деталь: | Terminal Plate - Thermostat |
| Парткод: | B027 4092 |
| Деталь: | Harness - Sheet |
| Парткод: | B027 4079 |
| Деталь: | Rear Side Plate |
| Парткод: | B031 4125 |
| Деталь: | Decal - Warning (High Temperature) |
| Парткод: | AA00 0302 |
| Деталь: | Decal - Warning (High Temperature)(CHN) |
| Парткод: | G065 7655 |
| Деталь: | Fusing Entrance Guide |
| Парткод: | A267 4085 |
| Деталь: | Frame:Fusing:Lower |
| Парткод: | B027 4072 |
| Деталь: | 1st Paper T ray Assembly |
| Парткод: | B027 7353 |
| Деталь: | 2nd Paper Tray Assembly |
| Парткод: | B027 7354 |
| Деталь: | Paper Set Decal |
| Парткод: | B027 2892 |
| Деталь: | Front Side Fence Assembly |
| Парткод: | B024 2884 |
| Деталь: | Front Side Fence |
| Парткод: | B024 2851 |
| Деталь: | Front Stopper Lever |
| Парткод: | A267 2858 |
| Деталь: | Lower Slider - End Fence |
| Парткод: | B024 2874 |
| Деталь: | END FENCE |
| Парткод: | A267 2853 |
| Деталь: | Seal - End Fence |
| Парткод: | A267 2900 |
| Деталь: | Upper Slider - End Fence |
| Парткод: | B024 2866 |
| Деталь: | Bottom Plate |
| Парткод: | B024 2861 |
| Деталь: | Lift Plate - Bottom Plate |
| Парткод: | B024 2856 |
| Деталь: | Decal - Side Fence |
| Парткод: | B027 7352 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A267 2860 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Rear Side Fence |
| Парткод: | B024 2852 |
| Деталь: | Rear Side Fence Assembly |
| Парткод: | B024 2885 |
| Деталь: | Shaft - Tray Raising |
| Парткод: | A267 2854 |
| Деталь: | Friction pad |
| Парткод: | A860 2831 |
| Деталь: | Friction pad |
| Парткод: | A267 2831 |
| Деталь: | Pressure Spring - Friction Pad |
| Парткод: | A267 2834 |
| Деталь: | Paper Size Detector |
| Парткод: | B024 7343 |
| Деталь: | Shaft - Roller |
| Парткод: | A267 2865 |
| Деталь: | Spring Plate |
| Парткод: | A267 2870 |
| Деталь: | Roller Bracket |
| Парткод: | A267 2864 |
| Деталь: | Sheet - Paper Tray Holder |
| Парткод: | A267 2898 |
| Деталь: | Cushion - Paper Feed Tray |
| Парткод: | A267 2913 |
| Деталь: | PAPER TRAY |
| Парткод: | B024 2850 |
| Деталь: | Shield - Side Fence |
| Парткод: | A267 2897 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | G697 2677 |
| Деталь: | Spring Plate - Slider |
| Парткод: | A267 2875 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | Gear - 16Z |
| Парткод: | A267 2869 |
| Деталь: | Spring Plate - Grounding |
| Парткод: | A267 2878 |
| Деталь: | Sponge - Paper Feed Tray |
| Парткод: | A267 2899 |
| Деталь: | BASE PAD |
| Парткод: | A267 2917 |
| Деталь: | Fusing Unit (115V) |
| Парткод: | B031 7280 |
| Деталь: | Fusing Unit (230V) |
| Парткод: | B031 7530 |
| Деталь: | Fusing Unit (CHN) |
| Парткод: | B031 7531 |
| Деталь: | Decal Warning (High Temperature) |
| Парткод: | AA00 0301 |
| Деталь: | Upper Frame - Fusing Unit |
| Парткод: | A267 4151 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3219 |
| Деталь: | Fusing Upper Stopper |
| Парткод: | A267 4157 |
| Деталь: | Fusing Unit Drawer - 120V |
| Парткод: | B031 7274 |
| Деталь: | Fusing Unit Drawer - 230V |
| Парткод: | B031 7524 |
| Деталь: | Spring - Hot Roller |
| Парткод: | A267 4066 |
| Деталь: | Ball Bearing - 8x19x6 |
| Парткод: | AE03 0030 |
| Деталь: | Knob Screw |
| Парткод: | A267 4161 |
| Деталь: | Harness - Guide |
| Парткод: | B027 4077 |
| Деталь: | Pressure Roller - MM27 |
| Парткод: | AE02 0138 |
| Деталь: | Bearing 30x42x7 |
| Парткод: | G052 4618 |
| Деталь: | C Ring - Hot Roller |
| Парткод: | B031 4056 |
| Деталь: | Tension Spring - 27.7N |
| Парткод: | B031 4114 |
| Деталь: | Spring - Fusing Stripper |
| Парткод: | A267 4103 |
| Деталь: | Hot Roller Stripper |
| Парткод: | AE04 4025 |
| Деталь: | Upper Guide Plate |
| Парткод: | A267 4155 |
| Деталь: | Stripper Pawl Bracket |
| Парткод: | B024 4101 |
| Деталь: | Open/Close Shield |
| Парткод: | A267 4159 |
| Деталь: | Open/close Spring |
| Парткод: | A267 4158 |
| Деталь: | Terminal Plate - Fusing Lamp |
| Парткод: | B024 4092 |
| Деталь: | Gear - 48Z |
| Парткод: | AB01 1400 |
| Деталь: | Hot Roller |
| Парткод: | AE01 1058 |
| Деталь: | Fusing Lamp - 120V (SUB) |
| Парткод: | AX44 0141 |
| Деталь: | Fusing Lamp - 230V (SUB) |
| Парткод: | AX44 0143 |
| Деталь: | Fusing Lamp - 120V (MAIN) |
| Парткод: | AX44 0140 |
| Деталь: | Fusing Lamp - 230V (MAIN) |
| Парткод: | AX44 0142 |
| Деталь: | Laser Unit Assembly |
| Парткод: | B027 1900 |
| Деталь: | Decal - LD |
| Парткод: | G029 1980 |
| Деталь: | Supporting Plate - Imaging Unit |
| Парткод: | B024 1971 |
| Деталь: | Cover - Polygon Motor |
| Парткод: | B024 1917 |
| Деталь: | Cover - Laser Unit |
| Парткод: | A267 1938 |
| Деталь: | MIRROR HOLDER |
| Парткод: | A267 1942 |
| Деталь: | MIRROR |
| Парткод: | AC01 0005 |
| Деталь: | Rear Holder - BTL |
| Парткод: | A267 1941 |
| Деталь: | Plate - Sync.detector Board |
| Парткод: | A267 1944 |
| Деталь: | Sync Detector Harness |
| Парткод: | B024 5222 |
| Деталь: | Laser Sync. Detector |
| Парткод: | A232 5310 |
| Деталь: | Rear Holder - F Theta Mirror |
| Парткод: | A232 1922 |
| Деталь: | F Theta Mirror |
| Парткод: | G020 1968 |
| Деталь: | Laser Diode Unit |
| Парткод: | B027 1915 |
| Деталь: | Laser Diode Unit (B097) |
| Парткод: | B031 1915 |
| Деталь: | Cylindrical Lens |
| Парткод: | G020 1966 |
| Деталь: | Cylindrical Lens Holder |
| Парткод: | A2321927 |
| Деталь: | Cylindrical Lens |
| Парткод: | G029 1975 |
| Деталь: | Sync Detector Mirror |
| Парткод: | G020 1911 |
| Деталь: | Mirror Holder - Sync.detector |
| Парткод: | A267 1933 |
| Деталь: | Front Holder - F Theta Mirror |
| Парткод: | A232 1921 |
| Деталь: | BTL Lens |
| Парткод: | G020 1969 |
| Деталь: | Front Holder - BTL |
| Парткод: | A267 1940 |
| Деталь: | Shield Glass - Polygon Morror Motor |
| Парткод: | G020 1937 |
| Деталь: | Collar-polygon Motor |
| Парткод: | A232 1916 |
| Деталь: | Harness - Polygon Mirror Motor |
| Парткод: | B024 5224 |
| Деталь: | Polygon Mirror Motor |
| Парткод: | AX06 0181 |
| Деталь: | Polygon Mirror Motor (B097) |
| Парткод: | AX06 0198 |
| Деталь: | Shield Glass |
| Парткод: | AC03 0077 |
Коды ошибок
101
120
121
122
123
144
192
193
195
196
197
198
199
302
320
322
323
350
351
352
353
354
355
389
390
391
392
399
401
402
411
490
500
501
502
503
504
506
508
509
510
520
541
542
543
544
545
546
547
548
590
611
612
620
621
630
632
633
634
635
640
641
650
670
672
720
722
724
725
726
727
728
730
731
732
770
791
792
793
800
804
818
819
820
821
822
823
824
825
826
827
828
829
835
836
837
838
840
841
850
851
853
854
855
856
857
860
861
862
863
864
865
870
871
880
900
901
920
925
951
953
954
955
964
984
986
990
991
992
995
996
997
998
999
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 122 |
| Display: | Service Call 122: Error |
| Description: | Finisher Decurler Failure, Code 122 The level of the Decurler Cam Home Sensor did not change 4 seconds after the Decurler Cam Clutch has turned on. |
| Causes: | • Decurler Cam Clutch • Stacker Motor • Finisher Control Board |
| Remedy: | 1 1. Rotate the actuator while running the Decurler Cam Position test in diagnostics. 2. Does the value change between H and L? Go to step 2. Troubleshoot using the transmissive sensor procedure. 2 Does the decurler cam clutch operate in diagnostics? Check for a mechanical problem with the decurler cam clutch drive. If no problem is found replace the clutch. Go to step 3. 3 Is +24 VDC present at P/J 849-1? Replace the decurler cam clutch. Go to step 4. 4 Is +24 VDC present at test point 5 on the finisher control board? Replace the finisher control board. Troubleshoot the +24 VDC interlock circuit. 5 Is +24 VDC present at P/J 847-11 with the Finisher Stacker Motor Down test running in diagnostics? Replace the stacker motor. Replace the finisher control board |
| Error code: | 123 |
| Display: | Service Call 123: Error |
| Description: | Finisher Set Clamp Failure, Code 123 The set clamp home sensor did not turn on within 2 seconds after the set clamp started operation. |
| Causes: | • Set Clamp Solenoid • Finisher Control Board |
| Remedy: | 1 1. Check the Set Clamp home sensor in diagnostics. 2. Does the value change from H to L while rotating the actuator? Go to step 2. Use the transmissive Sensor procedure to diagnose and repair the sensor. 2 Does the solenoid energize when running the Set Clamp Paddle test in diagnostics? Go to step 3. Go to step 4. 3 1. Run the Eject Forward Test and then the Eject Release Test in diagnostics. 2. Does the set clamp paddle turn once? Replace the finisher control board. Go to step 4. 4 Is +24 VDC present at P848A-10? Go to step 5. Go to step 6. 5 Is +24 VDC present at P848A-11? Replace the finisher control board. Replace the set clamp solenoid. 6 Is +24 VDC present at test point 9 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 192 |
| Description: | SBU auto-adjustment error During SBU auto-adjustment the detected white level was out of range. |
| Causes: | • SBU auto adjustment was not done correctly • Exposure lamp defective • SBU harness defective • Bad connection • Defect in optics system (dirty scanner mirror, mirror out of position. etc.) • Defective stabilizer board (or connector) • Incorrect start position or length for white plate scanning • Scanner HP sensor out of position |
| Error code: | 193 |
| Description: | Image transfer error The IPU board does not finish within 1 minute after the image data has been transferred to the controller board. |
| Causes: | • IPU board defective • Controller board defective • Video controller defective |
| Error code: | 195 |
| Description: | Serial Number Error |
| Causes: | The serial number stored in the memory (EGB) is not correct. |
| Remedy: | EEPROM defective EGB replaced without original EEPROM |
| Error code: | 196 |
| Description: | Replace Imaging Unit or Imaging Unit Is Near End of Life The Imaging Unit Life counter indicates the Imaging Unit is near or has reached its end of life. |
| Causes: | • Imaging Unit, PL6.1.1 • CRUM Connector, PL7.1.4 • PHD2 Harness, PL7.1.7 • FAN/PHD/MOT Harness, PL10.1.9 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Imaging Unit PL6.1.1 • CRUM Connector PL7.1.4 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Replace the Imaging Unit. Does the error persist? Go to Step 3. Complete 3 Check Imaging Unit CRUM connection. Are P/J710 and P/J484 connected? Go to Step 4. Reconnect the CRUM Connector. 4 Check all pins on the PHD2 Harness PL7.1.7 for continuity. 1. Disconnect P/J710 and P/J484. 2. Check continuity between J484<=>J710 Go to Step 5. Replace the PHD2 Harness. 5 Check all pins on the FAN/PHD/MOT Harness for continuity. 1. Disconnect P/J484 and P/J48. 2. Check continuity between J48 <=> P484 Replace the Engine Control Board. Replace the FAN/ PHD/MOT Harness |
| Error code: | 197 |
| Description: | DFGATE error The DFGEATE signal has already been asserted at the original scan. |
| Causes: | • ADF interface cable defective • SBCU board defective • Mismatched firmware between the SBCU board and ADF |
| Error code: | 198 |
| Description: | Memory address error The IPU board does not receive the memory address from the controller board. |
| Causes: | • Mismatched firmware between the SBCU board and controller board • Controller defective • SBCU defective • IPU board defective Note: Before you replace a board, update the firmware. This can repair the error. |
| Error code: | 199 |
| Description: | Service Reflash RIP |
| Causes: | • ADF interface cable defective • SBCU board defective • Mismatched firmware between the SBCU board and ADF |
| Remedy: | The printer has detected an invalid version of the RIP code and must be reflashed to the approved version. Contact your next level support. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 320 |
| Display: | Reset fuser 320: Fuser error |
| Description: | Same unit not detected upon power ON or opening cover. |
| Causes: | 1) Is error message displayed? 2) Is fuser unit set properly? 3) Does error reoccur? |
| Remedy: | Check if fuser is set properly. Reset fuser and turn ON power again. Replace fuser unit assembly. |
| Error code: | 322 |
| Description: | Synchronization error The synchronization signal was not issued within 500 ms after the LD fired while the polygon motor was turning at the prescribed number of revolutions. |
| Causes: | • Laser synchronization board connectors or harness loose, disconnected, or damaged • Laser synchronization board defective or out of position • LD drive board defective |
| Remedy: | 1. Check the harness connection of the development HVPS. 2. Replace the development HVPS. 3. Replace the development unit. |
| Error code: | 323 |
| Display: | Open/close cover 323: Paper thickness error |
| Description: | Sensor output out of range with no media. (Only for Factory Mode) |
| Causes: | 1) Are foreign objects mixed in sensor? 2) Does printer recover when detecting paper thickness by opening/closing tray? 3) Does printer recover by power OFF/ON. |
| Remedy: | Remove foreign objects. Normal. |
| Error code: | 350 |
| Description: | ID sensor error 1 One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. Vsp greater than or equals 2.5V Vsg less than 2.5 Vsp = 0V Vsg = 0 |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 351 |
| Description: | ID sensor error 2 The ID sensor output voltage is 5.0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 352 |
| Description: | ID sensor error 3 For 2 s during the ID sensor pattern check, the ID sensor pattern edge voltage is not 2.5V or the pattern edge is not detected within 800 ms. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 353 |
| Description: | ID sensor error 4 One of the following ID sensor output voltages is detected at ID sensor initialization. Vsg less than 4.0V when the maximum PWM input (255) is applied to the ID sensor. Vsg greater than or equal to 4.0V when the minimum PWM input (0) is applied to the ID sensor. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 354 |
| Display: | Set new fuser 354: Fuser life |
| Description: | Fuser life (occurs when fuser life continuation is OFF). |
| Causes: | Right after replacing fuser? |
| Remedy: | Check fuser life. Replace fuser. |
| Error code: | 355 |
| Display: | Set new belt 355: Belt life |
| Description: | Belt life notified (alarm). Print N-count by opening and closing cover. |
| Causes: | Right after replacing belt? |
| Remedy: | Check belt life. Replace belt. |
| Error code: | 389 |
| Display: | Open top cover 389: Paper jam |
| Description: | Jam generated in paper path. |
| Causes: | Open front cover and check jammed paper. |
| Remedy: | Remove jammed paper. |
| Error code: | 390 |
| Display: | Check MP tray 390: Paper jam |
| Description: | Paper jam during paper feed from MT. |
| Causes: | Check for miss-fed paper around MT cassette. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace MT. |
| Error code: | 391 |
| Description: | TD sensor error: Auto adjust error During automatic adjustment of the TD sensor, output voltage was less than 1.8V, or more than 4.8V during TD sensor initial setting |
| Causes: | • TD sensor connector or harness loose, broken, defective • TD sensor defective • IOB defective • Toner supply defective (confirm that the toner seal strip has been removed from toner cartridge) |
| Remedy: | 1. Check the harness or harness connection. 2. Clean the surface of the quenching lamp glass. |
| Error code: | 392 |
| Description: | Development Bias Error The development bias feedback voltage was less than 0.3 V for longer than 200 ms while the PWM duty value was more than 5% (indicating a development bias leak). |
| Causes: | • Bias terminal damaged • High voltage cable damaged, defective • CGB power pack defective |
| Error code: | 399 |
| Description: | Drum/Development motor error: Y The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on. |
| Causes: | • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system |
| Remedy: | 1. Check or replace the harness. 2. Replace the drum/development motor. 3. Replace the 24V fuse on the PSU. |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 411 |
| Display: | SVC 411 ERROR |
| Description: | IRQ timer 1 error |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | Replace the Controller board. |
| Error code: | 490 |
| Display: | Set 490: No paper in MP tray (* stands for A4 B4, etc.) |
| Description: | ITB (Image Transfer Belt) Unit Set Error |
| Causes: | The TM sensor does not detect the reflection from the ITB. |
| Remedy: | • No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S |
| Error code: | 500 |
| Description: | Transport/Fusing Motor Error |
| Causes: | The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the transport/fusing motor. Replace it if necessary. |
| Error code: | 501 |
| Display: | Service Call 501: Error |
| Description: | Tray 1 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503 |
| Display: | Service Call 503: Error |
| Description: | Tray 3 must be rebuilt |
| Causes: | (A model other than D581) Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. (D581) Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 504 |
| Description: | Tray 4 must be rebuilt |
| Causes: | The 2nd tray of D580, 1st tray of D580 when D579 and D580 are attached, the bottom D579 when two units of D579 are attached, or D631 when D581 and D631 are attached. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection D581 when D579 and D581 are attached.Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 506 |
| Display: | SYSTEM HALT (*) 506 : STATION SENS |
| Description: | Bypass must be rebuilt |
| Causes: | • Paper tray unit main motor connector or harness loose, broken, defective • Motor overload due to an obstruction • Motor defective |
| Remedy: | 1. Replace the tray 3 or 4 lift motor. 2. Replace the tray 3 or 4 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3 or 4. |
| Error code: | 508 |
| Description: | Replace black developer |
| Causes: | • HP sensors on the left and right side loose, disconnected, defective • Cutter motor harness damaged, defective • HP sensors defective • Cutter motor defective Note: Paper can be fed from the bypass table if the roll feeder or paper cassette is not operationg. |
| Error code: | 509 |
| Display: | SYSTEM HALT (*) 509 : HDC POSCNT |
| Description: | Replace red developer |
| Causes: | • Poor connection or defective tray 5 or 6 lift motor • Poor connection or defective tray 5 or 6 lift sensor • Remaining paper or another obstruction has stopped the tray and motor. • Pick-up solenoid 5 or 6 connector is loose. • Pick-up solenoid 5 or 6 is blocked by an obstruction. |
| Remedy: | 1. Replace the tray 5 or 6 lift motor. 2. Replace the tray 5 or 6 lift sensor. 3. Check or clear obstacles around pick-up solenoid 5 or 6. |
| Error code: | 510 |
| Display: | SYSTEM HALT (*) 510 : X ORGIN |
| Description: | Replace green developer |
| Causes: | • Tray lift motor defective or connector disconnected • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Remedy: | 1. Check the harness connection or replace it. 2. Replace the bypass tray lift motor. 3. Replace the bypass upper limit sensor. 4. Replace the bypass lower limit sensor. 5. Check or clear obstacles around the bypass pick-up solenoid. |
| Error code: | 520 |
| Description: | Replace optics filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 548 |
| Description: | Low Temperature Error |
| Causes: | The center thermistor detects 100°C or less for 4 seconds. |
| Remedy: | • Defective fusing lamp • Defective thermistor 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.d |
| Error code: | 590 |
| Description: | Toner collection motor error The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on. |
| Causes: | • Motor lock due to obstruction • Motor driver board defective • Motor connection loose, defective • Toner collection motor sensor disconnected, sensor defective • Rotational transmission shaft (o6 x 30) missing |
| Error code: | 611 |
| Display: | ERROR 611 Case Weight |
| Description: | Mechanical counter error: FC This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 612 |
| Display: | ERROR 612 INK LVL LOW |
| Description: | BICU - ADF communication/command abnormal A command that cannot be executed was sent from the main machine to the ADF. |
| Causes: | • A software error, result of an abnormal procedure. |
| Remedy: | Enter the cartridge weight from "CART WEIGHT" menu of "SET UP". |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 630 |
| Description: | CSS communication error A communication error occurred during communication with the CSS. |
| Causes: | • Communication line error |
| Remedy: | Logging only. |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 633 |
| Description: | Key/card counter device error 2 During communication with the device, the MCU received a break (Low) signal. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 640 |
| Description: | Communication error: Engine Controller (Check sum error) Sum value is added each command frame. Sum check means: STX xx xx xx xx sum ETX -> The least significant 7 bits of xx + xx + xx+ xx is compared with the sum Example: STX 80h 81h 82h 83h 06h ETX -> 80h + 81h + 82h + 83h = 206h If sum value is 06h, data is correct. This SC is not displayed when it occurs; count is executed only by logging. |
| Causes: | Hard error with PCI |
| Remedy: | 1. Turn the main switch off and on. |
| Error code: | 641 |
| Description: | BICU control data transfer abnormal A sampling of the control data sent from the BICU reveals an abnormality. |
| Causes: | • Defective controller board • External noise • Defective BCU |
| Remedy: | 1. Replace the controller board. 2. Replace the BCU. |
| Error code: | 650 |
| Description: | @Remote communication error 1 A dial-up or modem error occurred during @Remote operation. (This error occurs only during @Remote operation.) |
| Causes: | • Modem line disconnected • Modem board missing or not properly installed |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 720 |
| Description: | Fan folder transport motor error A transport motor lock signal was detected for more than 5 sec. while the motor was running. |
| Causes: | • Transport motor harness connector loose, disconnected, broken • Motor overload due to an obstruction • Transport motor defective • Fan folder unit MCU defective |
| Error code: | 722 |
| Description: | Finisher jogger motor error The finisher jogger HP sensor did not return to the home position, or move out of the home position, within 1.25 sec. Staple mode cannot be used. |
| Causes: | • Jogger motor connector or harness loose, broken, defective • Jogger motor defective • Jogger HP sensor connector or harness loose, broken, defective • Jogger HP sensor defective |
| Error code: | 724 |
| Description: | Finisher staple hammer motor error Stapling does not finish within 150 ms after the staple hammer motor turned on. Staple mode cannot be used. |
| Causes: | • Staple jam • Stapler overload caused by trying to staple too many sheets • Staple hammer motor connector or harness loose, broken, defective • Staple hammer motor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the staple hammer motor HP sensor if the motor is rotating. 4. Replace the finisher main board. |
| Error code: | 725 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor. 4. Replace the finisher main board. |
| Error code: | 726 |
| Description: | Front shift jogger motor error (B703) The sides fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift jogger motor disconnected, defective • Shift jogger motor overloaded due to obstruction • Shift jogger HP sensor disconnected, defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift jogger HP sensor 4. Replace the shift jogger motor. 5. Replace the finisher main board. |
| Error code: | 727 |
| Description: | Rear shift jogger motor (B703) The side fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code |
| Causes: | Motor harness disconnected, loose, defective Motor defective Motor overload HP defective boar |
| Error code: | 728 |
| Description: | Shift jogger retraction motor error (B703) The side fences do not retract within the prescribed time after the retraction motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray jogger lift HP sensor. 4. Replace the shift jogger retraction motor. 5. Replace the finisher main board. |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 731 |
| Description: | Finisher exit guide motor error After the finisher exit guide motor turned on, the exit guide sensor did not activate within 800 ms. |
| Causes: | • Finisher exit guide motor defective harness or connector loose, broken, defective • Finisher exit guide motor defective • Finisher exit guide sensor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the upper tray exit motor. 4. Replace the finisher main board. |
| Error code: | 732 |
| Description: | Finisher shift roller motor error The shift roller HP sensor does not activate within the prescribed time after the shift roller motor turns on. After 2 counts, the SC is logged as a jam. |
| Causes: | • Shift roller HP sensor defective • Sensor harness disconnected, defective • Shift roller motor defective • Finisher main board defective • Shift roller motor overload |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray exit motor. 4. Replace the finisher main board. |
| Error code: | 770 |
| Description: | Shift motor error The shift motor HP sensor does not detect any change for 1.86 seconds after the shift motor has turned on at power on or during its operation. |
| Causes: | Defective shift motor. Defective shift motor HP sensors. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 791 |
| Description: | Bridge unit error The machine recognizes the finisher, but does not recognize the bridge unit. |
| Causes: | The bridge unit is not installed. Defective bridge unit. Re-install the bridge unit. Turn the main power switch off and on. |
| Remedy: | • Re-install the bridge unit. • Turn the main power switch off and on. |
| Error code: | 792 |
| Description: | Finisher error The machine does not recognize the finisher, but recognizes the bridge unit. |
| Causes: | The finisher`s connection is faulty. The finisher is not attached to a device equipped with the bridge unit. Defective finisher. |
| Remedy: | Reconnect the finisher or bridge unit, and then turn the main power switch off and then back on. |
| Error code: | 793 |
| Description: | Finisher gathering roller motor error |
| Causes: | • Motor overload • Loose connection of the gathering roller motor • Defective gathering roller motor |
| Remedy: | • Check the connections to the gathering roller motor. • Replace the gathering roller motor. |
| Error code: | 800 |
| Description: | Startup without video output end error (K) Video transfer to the engine is started, but the engine did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Error code: | 804 |
| Display: | SYSTEM HALT (*) 804 : (C)DMA ADDR |
| Description: | Startup without video input end (K) A video transmission was requested from the scanner, but the scanner did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 825 |
| Description: | Self-diagnostic Error: Optional NVRAM The resident non-volatile RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional NVRAM (user account enhancement unit) on the controller board • Replace the controller board |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 835 |
| Display: | SYSTEM HALT (*) 835 : FW/PRN MDL |
| Description: | Self-diagnostic error: Centronic device |
| Causes: | [1102] Loopback connector is connected but check results in an error. • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [110C] Loopback connector is connected but check results in an error. • ASIC device error • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [1120] Centronic loopback connector is not connected for detailed self-diagnostic test. • Centronic loopback connector not connected correctly • Centronic loopback connector defective • ASIC device defective Replace the controller board. |
| Error code: | 836 |
| Display: | SYSTEM HALT (*) 836 : FW/SV MDL |
| Description: | Self-diagnostics error: Font ROM (standard) |
| Causes: | Turn the main switch off and on. Replace the standard ROM-DIMM. |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the controller board. |
| Error code: | 837 |
| Display: | SYSTEM HALT (*) 837 : FW/PRN MDL |
| Description: | Self-diagnostic error - Optional font ROM The data in the font ROM (optional ROM-DIMM) is damaged. |
| Causes: | • Defective optional ROM-DIMM. |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the optional ROM-DIMM. |
| Error code: | 838 |
| Display: | SYSTEM HALT (*) 838 : FW/SV MDL |
| Description: | Self-diagnostic Error 10: Clock Generator A verify error occurred when setting data was read from the clock generator via the I2C bus. |
| Causes: | • Replace the controller board |
| Error code: | 840 |
| Description: | EEPROM access error During the I/O processing, reading error is occurred. The 3rd reading failure issues this SC code. During the I/O processing, writing error is occurred. |
| Causes: | Defective EEPROM |
| Error code: | 841 |
| Description: | EEPROM read error Mirrored data of the EEPROM is different from the original data in EEPROM. |
| Causes: | Data in the EEPROM is overwritten for some reason. |
| Error code: | 850 |
| Description: | Net I/F error Duplicate IP addresses. Illegal IP address. Driver unstable and cannot be used on the network |
| Causes: | • IP address setting incorrect • NIB (PHY) board defective • Controller board defective |
| Remedy: | Turn the main switch off and on. |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 862 |
| Description: | Bad sector number error The number of bad sectors in the HDD (image data area) goes over 101. |
| Causes: | • Defective HDD |
| Remedy: | Format the HDD with SP5832-001. Replace the HDD. |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 871 |
| Description: | FCU Flash ROM Error The address book written into the flash ROM mounted on the FCU is detected as defective. |
| Causes: | • Flash ROM device defective • Replace flash ROM on the MBU |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 951 |
| Description: | NVRAM Secure NVRAM Missing |
| Causes: | • Software defective • BICU defective |
| Remedy: | Replace the system board. |
| Error code: | 953 |
| Description: | NVRAM Chip Failure |
| Causes: | • Firmware bug • Update the scanner firmware • IPU defective |
| Remedy: | Indicates the NVRAM chip on the interconnect board has failed. Replace the interconnect board. |
| Error code: | 954 |
| Description: | NVRAM CRC Failure |
| Causes: | • Firmware bug • IPU defective |
| Remedy: | Indicates the NVRAM experienced a CRC failure. Replace the interconnect board. |
| Error code: | 955 |
| Description: | Code CRC <loc> |
| Causes: | • Firmware bug • Hard disk unit defective • Controller defective • MCU defective • IPU defective |
| Remedy: | Replace the system board. Where <loc> = CRC Failure or ECC Failure on the system board. |
| Error code: | 964 |
| Description: | Emulation Error |
| Causes: | • Software defective |
| Remedy: | Indicates a failure within the Download Emulation which is programmed into the code overlay card. The specific error is as follows: 964 - Download Emulation CRC Failure. Checksum Failure. |
| Error code: | 984 |
| Display: | Service call 984: Error. |
| Description: | <device> |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected |
| Remedy: | Invalid command parameter received by the specified device. Note: Service errors 980 thru 984 <device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 986 |
| Display: | Service call 986: Error |
| Description: | Transparency (OHP) Sensor Error |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU Controller disconnected |
| Remedy: | 1 Are connectors CN4 (light emitting) and CN5 (light receiving) on the CK1 daughter board connected properly? Go to step 2. Plug the connector in securely. 2 Test the sensor. While actuating the sensor, does the voltage fluctuate between 0 V and +5 between pins 2 and 3 of connector CN7 of the printer controller board? Replace the printer controller board. Replace the MPF unit. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 995 |
| Description: | Finisher Main Feed Motor abnormal |
| Causes: | -01 D • Defective BCU • NVRAM Replacement error • Install the previous NVRAM • Input the serial number with SP5-811-004, and turn the main power switch off and on. -02 D • Defective NVRAM • Defective controller Perform SP5-825 to download the appropriate data to the NVRAM, and then turn the main power switch off and then back on. -03 D The serial number cannot be identified due to a mistake during controller replacement or mechanical failure. Replace the controller with the correct type. -04 D - Place all parts in the initial state, and then replace the parts according to the procedures described in the manuals. |
| Remedy: | 1 Is there jammed paper or other obstructions in the paper path? Clear the paper path. Go to step 2. 2 Check to ensure the connector PJ6 on the finisher control board and the feed motor assembly cable are properly connected. Are the cables properly connected? Go to step 3. Properly connect the cables. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pins 7 and 8 and +5 V dc (–10%) between pins 7 and 6 on the feed motor assembly cable connector CN1. Is either voltage missing? Go to step 4. Go to step 5. 4 Disconnect the feed motor assembly cable and PJ6 on the finisher control board. Measure continuity on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 5 Replace the feed motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 6 Measure for +24 V dc between pins 1 and 2 on connector PJ3 on the finisher control board. Measure for +5 V dc between pins 1 and 3 on PJ2 on the finisher control board. Is either voltage missing? Replace the power supply. Replace the finisher control board. |
| Error code: | 996 |
| Description: | Finisher Jogging Motor Error |
| Causes: | • FCU board hardware or firmware defective • Replace FCU board |
| Remedy: | 1 Are there foreign objects or obstructions in the jogging assembly? Clear the objects or obstruction. Go to step 2. 2 Are the jogging motor connectors CN2 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pin 1 on CN2 and frame ground. Is +24 V dc present? Go to step 4. Go to step 5. 4 Replace the jogging motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN2 and PJ5. Perform a continuity check on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 6 Check for +24 V dc (–10%) between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
| Error code: | 999 |
| Display: | Service call 999: Error |
| Description: | Stapler Motor Error |
| Causes: | • Color registration (MUSIC) failure |
| Remedy: | 1 Are staples jammed in the stapler? Go to step 2. Go to step 3. 2 Clear the staple jam and run the staple test in diagnostic mode or run a staple job. Does the problem reoccur? Replace the staple cartridge and to go step 4. Problem solved. 3 Are the connectors CN5 on the stapler and PJ1 on the finisher control board securely connected? Go to step 5. Securely connect the connectors. 4 Did replacement of the stapler cartridge resolve the problem? Problem resolved. Replace the stapler. 5 Make sure the finisher set switch is activated. Measure for 5 V dc between pins 11 and 12 on stapler connector CN5. Is 5 V dc present? Replace the stapler. Replace the finisher control board. 6 Did replacement of the finisher control board correct the problem? Problem solved. Go to step 7. 7 Is there continuity on the stapler to finisher control board cable? Replace the power supply. Replace the cable. |
