Ricoh Aficio 3030
Рейтинг
Модули
OPTICS SECTION 1 (B205/B209/D007/D008)
FUSING UNIT 1 (B205/B209/D007/D008)
DRIVE SECTION 3 (B205/B209/D007/D008)
FUSING UNIT 2 (B205/B209/D007/D008)
PAPER FEED SECTION 1 (B205/B209/D007/D008)
LASER UNIT (B205/B209/D007/D008)
ELECTRICAL SECTION 1 (B205/B209/D007/D008)
FRAME SECTION (B205/B209/D007/D008)
DRIVE SECTION 2 (B205/B209/D007/D008)
PCU SECTION (B205/B209/D007/D008)
PAPER FEED SECTION 2 (B205/B209/D007/D008)
OPERATION PANEL (B205/B209/D007/D008)
PLATEN COVER (OPTION B406)
EXTERIOR 1 (B205/B209/D007/D008)
PAPER REGISTRATION (B205/B209/D007/D008)
OPTICS SECTION 2 (B205/B209/D007/D008)
DRIVE SECTION 4 (B205/B209/D007/D008)
PAPER TRAY (B205/B209/D007/D008)
ELECTRICAL SECTION 2 (B205/B209/D007/D008)
TRANSFER UNIT (B205/B209/D007/D008)
EXTERIOR 2 (B205/B209/D007/D008)
DRIVE SECTION 1 (B205/B209/D007/D008)
TONER HOPPER UNIT (B205/B209/D007/D008)
OPTICS SECTION 3 (B205/B209/D007/D008)
PAPER FEED SECTION 3 (B205/B209/D007/D008)
PAPER EXIT (B205/B209/D007/D008)
Детали DRIVE SECTION 4 (B205/B209/D007/D008)
| Деталь: | Cushion Glass |
| Парткод: | B093 1862 |
| Деталь: | Frame:Front Rear:Rif:Tog |
| Парткод: | B093 1813 |
| Деталь: | Bracket:Scale:Assy |
| Парткод: | B090 1742 |
| Деталь: | STEPPED SCREW |
| Парткод: | A193 1759 |
| Деталь: | Scale:Inner Back |
| Парткод: | B090 1701 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Sheet - Photointerrupter |
| Парткод: | A267 1820 |
| Деталь: | Hinge Bracket - Platen Cover |
| Парткод: | B093 1814 |
| Деталь: | Inner cover |
| Парткод: | B091 1815 |
| Деталь: | Exposure Glass |
| Парткод: | A250 1752 |
| Деталь: | Scale:Left:Assy |
| Парткод: | B090 1680 |
| Деталь: | Harness - Home Position Sensor |
| Парткод: | B027 5208 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 8 025 276 |
| Деталь: | Fusing Unit (120V) |
| Парткод: | B209 7280 |
| Деталь: | Fusing Unit (230V) |
| Парткод: | B209 7530 |
| Деталь: | Decal Warning (High Temperature) |
| Парткод: | AA00 0301 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3219 |
| Деталь: | Fusing Upper Stopper |
| Парткод: | A267 4157 |
| Деталь: | Drawer:Fusing:120V |
| Парткод: | B209 7274 |
| Деталь: | Drawer:Fusing:230V |
| Парткод: | B209 7524 |
| Деталь: | Spring:Flange:Pressure Roller |
| Парткод: | B091 4066 |
| Деталь: | Ball Bearing - 8x19x6 |
| Парткод: | AE03 0030 |
| Деталь: | Knob Screw |
| Парткод: | A267 4161 |
| Деталь: | Guide:Harness:Plate |
| Парткод: | B206 4077 |
| Деталь: | Pressure Roller:Mm27 |
| Парткод: | AE02 0161 |
| Деталь: | Bearing 30x42x7 |
| Парткод: | G052 4618 |
| Деталь: | C Ring - Hot Roller |
| Парткод: | B031 4056 |
| Деталь: | Tension Spring - 34.2n |
| Парткод: | B031 4114 |
| Деталь: | Spring - Fusing Stripper |
| Парткод: | A267 4103 |
| Деталь: | Hot Roller Stripper |
| Парткод: | AE04 4025 |
| Деталь: | Guide Plate:Fusing:Upper:Printing |
| Парткод: | B206 4155 |
| Деталь: | Bracket:Stripper Pawls |
| Парткод: | B090 4101 |
| Деталь: | Open/Close Shield |
| Парткод: | A267 4159 |
| Деталь: | Spring:Open And Close:Guide |
| Парткод: | B091 4158 |
| Деталь: | Terminal:Heater |
| Парткод: | B090 4092 |
| Деталь: | Gear - 48Z |
| Парткод: | AB01 1400 |
| Деталь: | Hot Roller |
| Парткод: | AE01 1003 |
| Деталь: | Fusing Lamp - 120V |
| Парткод: | AX44 0141 |
| Деталь: | Fusing Lamp - 230V |
| Парткод: | AX44 0143 |
| Деталь: | Fusing Lamp - 120V |
| Парткод: | AX44 0140 |
| Деталь: | Fusing Lamp - 230V |
| Парткод: | AX44 0142 |
| Деталь: | Frame:Fusing:Upper |
| Парткод: | B206 4151 |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 8 046 123 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Bracket:Protecter:Transport:Cl |
| Парткод: | B090 2605 |
| Деталь: | Spring:Tension |
| Парткод: | B091 2615 |
| Деталь: | Bracket:Tension |
| Парткод: | B090 2602 |
| Деталь: | TIMING PULLEY - 18T |
| Парткод: | AB03 0627 |
| Деталь: | Gear - 31Z/54Z |
| Парткод: | AB01 1199 |
| Деталь: | Timing Belt - S3M - 315 |
| Парткод: | AA04 3517 |
| Деталь: | Timing Pulley - 20T |
| Парткод: | AB03 0626 |
| Деталь: | Harness:Density Sensor |
| Парткод: | B209 5236 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Harness:New Article Sensor |
| Парткод: | B209 5203 |
| Деталь: | Guard:Drive:Paper Feed:Right |
| Парткод: | B090 2596 |
| Деталь: | Magnetic Clutch - 38Z |
| Парткод: | B209 2617 |
| Деталь: | Magnetic Clutch - 50Z |
| Парткод: | B209 2616 |
| Деталь: | Stopper:Feed:Cl |
| Парткод: | B090 2604 |
| Деталь: | Gear - 38Z |
| Парткод: | AB01 1200 |
| Деталь: | Positioning Guide - Bypass Feed |
| Парткод: | A267 2601 |
| Деталь: | Snap Ring |
| Парткод: | B091 2607 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw With Washer - M3x8 |
| Парткод: | 8 025 279 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | CT Connector - 4p |
| Парткод: | 11 024 924 |
| Деталь: | CLAMP |
| Парткод: | 11 050 283 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Roller - Lever |
| Парткод: | A267 3958 |
| Деталь: | Cover:Paper Feed Sensor |
| Парткод: | B090 4489 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | AA12 0094 |
| Деталь: | Shaft - Paper Overflow |
| Парткод: | A267 4479 |
| Деталь: | Stopper:Spring Plate:Outer |
| Парткод: | B091 4487 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | A267 4483 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0567 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0566 |
| Деталь: | Stopper:Spring Plate |
| Парткод: | B091 4486 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | A267 4474 |
| Деталь: | Feeler - Paper Overflow |
| Парткод: | A267 4478 |
| Деталь: | EXIT ROLLER |
| Парткод: | B209 4475 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1404 |
| Деталь: | Guide Plate:Exit |
| Парткод: | B090 4454 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Stopper - Right Upper Cover |
| Парткод: | A267 1349 |
| Деталь: | Cover:Paper Exit Sub-unit:Guide Plate |
| Парткод: | B209 1346 |
| Деталь: | Harness:Paper Exit Section |
| Парткод: | B209 5207 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Photointerruptor |
| Парткод: | B207 1886 |
| Деталь: | Feeler - Paper Feed Sensor |
| Парткод: | A267 4476 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 2112 |
| Деталь: | Stay:Exit |
| Парткод: | B090 4452 |
| Деталь: | Decal - C |
| Парткод: | B090 4462 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 8 053 480 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Tapping Screw:Round Point:M3x6 |
| Парткод: | 8 025 291 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 8 025 283 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | Decal - High Temperature |
| Парткод: | AA00 0401 |
| Деталь: | Tray Heater Assy(120V) |
| Парткод: | A267 7350 |
| Деталь: | Tray Heater Assy(230V) |
| Парткод: | A267 7363 |
| Деталь: | Shoe:Supporter:Right |
| Парткод: | B090 2588 |
| Деталь: | Shoe:Supporter:Left |
| Парткод: | B090 2589 |
| Деталь: | Rubber Pad - H5 |
| Парткод: | AH01 0009 |
| Деталь: | Grip:Front |
| Парткод: | B209 2564 |
| Деталь: | Grip:Inner Back |
| Парткод: | B209 2567 |
| Деталь: | Bracket:Grip:Rear Left |
| Парткод: | B090 2576 |
| Деталь: | Bracket:Grip:Rear Right |
| Парткод: | B090 2573 |
| Деталь: | Guide Plate:Vertical Transport:Upper |
| Парткод: | B090 2653 |
| Деталь: | Bracket:Roller Clutch |
| Парткод: | B090 2677 |
| Деталь: | Spring Plate-roller Clutch |
| Парткод: | A267 2680 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Snap Ring |
| Парткод: | B090 2686 |
| Деталь: | Stopper Band |
| Парткод: | A267 2740 |
| Деталь: | Guide Plate:Lower |
| Парткод: | B090 2732 |
| Деталь: | Roller:Pull Out:Option Tray |
| Парткод: | B090 2742 |
| Деталь: | BUSHING - VERTICAL TRANSPORT |
| Парткод: | AA08 0249 |
| Деталь: | Compression Spring - 10n |
| Парткод: | B091 2739 |
| Деталь: | Shield - 2.5x7x363 |
| Парткод: | B209 2644 |
| Деталь: | Cover:Vertical Transport:Assy |
| Парткод: | B209 2728 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Decal - Vertical Transport Cover |
| Парткод: | B024 2737 |
| Деталь: | Guide:Spacer:Vertical Transport |
| Парткод: | B090 2736 |
| Деталь: | Guide Plate Lower Assy |
| Парткод: | B209 2724 |
| Деталь: | Cover:Grip:Right:Front |
| Парткод: | B209 2560 |
| Деталь: | Cover:Grip:Right:Rear |
| Парткод: | B209 2562 |
| Деталь: | Cover:Grip:Left:Rear |
| Парткод: | B209 2563 |
| Деталь: | Cover:Grip:Left:Front |
| Парткод: | B209 2561 |
| Деталь: | Screw:Spring Washer:M3x6 |
| Парткод: | 0950 3006N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 0451 4008N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Imaging Unit |
| Парткод: | B209 1900 |
| Деталь: | Decal - LD |
| Парткод: | G029 1980 |
| Деталь: | Supporting Plate:Cover:Imaging Unit |
| Парткод: | B206 1971 |
| Деталь: | Cover:Polygon Scanner:Assy |
| Парткод: | B090 1917 |
| Деталь: | Cover:Optical Housing |
| Парткод: | B090 1938 |
| Деталь: | MIRROR HOLDER |
| Парткод: | A267 1942 |
| Деталь: | MIRROR |
| Парткод: | AC01 0005 |
| Деталь: | Rear Holder - BTL |
| Парткод: | A267 1941 |
| Деталь: | Plate - Sync.detector Board |
| Парткод: | A267 1944 |
| Деталь: | Harness:Sync Detector |
| Парткод: | B209 5222 |
| Деталь: | PCB:Sync Detector:Sharp |
| Парткод: | B213 5320 |
| Деталь: | Rear Holder - F Theta Mirror |
| Парткод: | A232 1922 |
| Деталь: | F Theta Mirror |
| Парткод: | G020 1968 |
| Деталь: | Laser Diode Unit |
| Парткод: | B209 1915 |
| Деталь: | Cylindrical Lens |
| Парткод: | G020 1966 |
| Деталь: | Cylindrical Lens Holder |
| Парткод: | A232 1927 |
| Деталь: | Cylindrical Lens |
| Парткод: | G029 1975 |
| Деталь: | Sync Detector Mirror |
| Парткод: | G020 1911 |
| Деталь: | Mirror Holder - Sync.detector |
| Парткод: | A267 1933 |
| Деталь: | Front Holder - F Theta Mirror |
| Парткод: | A232 1921 |
| Деталь: | BTL Lens |
| Парткод: | G020 1969 |
| Деталь: | Front Holder - BTL |
| Парткод: | A267 1940 |
| Деталь: | Shield Glass - Polygon Morror Motor |
| Парткод: | G020 1937 |
| Деталь: | Collar-polygon Motor |
| Парткод: | A232 1916 |
| Деталь: | Harness:Polygon Mirror Motor |
| Парткод: | B209 5224 |
| Деталь: | Polygon Mirror Motor |
| Парткод: | B209 1898 |
| Деталь: | Shield Glass |
| Парткод: | B206 1977 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11 050 508 |
| Деталь: | Binding Self-tapping Screw:3x10 |
| Парткод: | 0452 3010N |
| Деталь: | Harness:Paper Feed:No.2 |
| Парткод: | B209 5234 |
| Деталь: | Harness:Paper Feed:No.1 |
| Парткод: | B209 5233 |
| Деталь: | Harness:Paper Feed:Motor |
| Парткод: | B209 5232 |
| Деталь: | Harness:Paper Size Sensor |
| Парткод: | B209 5231 |
| Деталь: | Harness:Registration Sensor |
| Парткод: | B209 5201 |
| Деталь: | Harness:Discharge Lamp |
| Парткод: | B209 5205 |
| Деталь: | Harness:Motor:Main |
| Парткод: | B209 5202 |
| Деталь: | Harness:Paper Exit Section |
| Парткод: | B209 5206 |
| Деталь: | Harness:HPS |
| Парткод: | B209 5208 |
| Деталь: | Harness:Motor:Scanner |
| Парткод: | B209 5200 |
| Деталь: | Main Switch:Assy |
| Парткод: | B209 5822 |
| Деталь: | Power Supply Unit:209W:DOM/NA |
| Парткод: | AZ23 0167 |
| Деталь: | Power Supply Unit:209W |
| Парткод: | AZ23 0168 |
| Деталь: | Choke Coil |
| Парткод: | B121 5018 |
| Деталь: | Harness:AC:Dehumidifier:EXP |
| Парткод: | B209 7635 |
| Деталь: | Power Supply Cord:Stopper:NA |
| Парткод: | B209 7611 |
| Деталь: | Power Supply Cord:Stopper:EU |
| Парткод: | B209 7631 |
| Деталь: | Harness:Power Supply Unit |
| Парткод: | B209 5212 |
| Деталь: | Bracket:IOB |
| Парткод: | B209 5838 |
| Деталь: | Harness:Door Switch:Front |
| Парткод: | B209 5204 |
| Деталь: | Harness:Paper Feed:Cl |
| Парткод: | B209 5209 |
| Деталь: | PCB:SBCU:C4:Assy (D007/D008) |
| Парткод: | B209 5051 |
| Деталь: | Harness:PP |
| Парткод: | B209 5217 |
| Деталь: | Bracket:Main Switch |
| Парткод: | B206 5823 |
| Деталь: | Bracket:Option |
| Парткод: | B209 1096 |
| Деталь: | Bracket:Option:Upper |
| Парткод: | B209 1097 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Edge - 17 |
| Парткод: | 11 050 334 |
| Деталь: | CLAMP |
| Парткод: | 11 050 460 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | WIRE SADDLE |
| Парткод: | 11 050 292 |
| Деталь: | Rocker Switch - AC250V 10A |
| Парткод: | 12 042 477 |
| Деталь: | Hexagonal Bolt - M3x8 |
| Парткод: | 8 046 075 |
| Деталь: | Fuse - 2A 125V |
| Парткод: | 11 070 910 |
| Деталь: | Fuse - 8A 125V |
| Парткод: | 11 070 919 |
| Деталь: | Philips Pan Head Screw - M4x6 |
| Парткод: | 8 010 149 |
| Деталь: | Fuse (Ceramic Case) - 15A - 125V |
| Парткод: | 11 070 629 |
| Деталь: | Fuse - 6.3A 125V |
| Парткод: | 11 070 907 |
| Деталь: | Fuse - 6.3A 240V |
| Парткод: | 11 070 920 |
| Деталь: | Fuse - 1A 240V |
| Парткод: | 11 070 922 |
| Деталь: | Fuse - 5A 240V |
| Парткод: | 11 070 879 |
| Деталь: | Safety Switch:Assy |
| Парткод: | B209 5808 |
| Деталь: | Bracket:Protect:Side Plate:Left Rear |
| Парткод: | B090 1085 |
| Деталь: | Guide Plate:Duct:Exhaust:C |
| Парткод: | B090 1106 |
| Деталь: | Fan Motor - Mm80 |
| Парткод: | B209 1105 |
| Деталь: | Duct:Fan Motor |
| Парткод: | B209 1102 |
| Деталь: | Grounding Plate - Upper Rear |
| Парткод: | A267 1089 |
| Деталь: | Grounding Plate - Lower Right |
| Парткод: | A267 1090 |
| Деталь: | Bracket:PCU |
| Парткод: | B090 1091 |
| Деталь: | Hinge:Door:Front |
| Парткод: | B090 1088 |
| Деталь: | Positioning Bracket - Laser Unit |
| Парткод: | A267 1930 |
| Деталь: | Total Counter:7FIG:24V |
| Парткод: | AX31 0049 |
| Деталь: | Lever:Door Switch:Assy |
| Парткод: | B092 5815 |
| Деталь: | Compression Spring:Door Switch |
| Парткод: | B091 5820 |
| Деталь: | Harness:Door Switch:Front |
| Парткод: | B209 5204 |
| Деталь: | Bracket:Micro Switch |
| Парткод: | B090 5813 |
| Деталь: | Tension Spring:Door Switch |
| Парткод: | B091 5821 |
| Деталь: | Arm:Scanner:Assy |
| Парткод: | B093 1093 |
| Деталь: | Guide Plate:Lengthwise:Left Rear |
| Парткод: | B209 1083 |
| Деталь: | Frame:Lengthwise:Right Rear:C |
| Парткод: | B090 1079 |
| Деталь: | Scanner Stay - Lower Right |
| Парткод: | B093 1080 |
| Деталь: | Frame:Lengthwise:Right Front:C |
| Парткод: | B090 1078 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0451 3006B |
| Деталь: | Pan Head Screw:M3x35 |
| Парткод: | 0313 0350N |
| Деталь: | MICRO SWITCH |
| Парткод: | 12 042 510 |
| Деталь: | Philips Pan Head Screw - M4x30 |
| Парткод: | 0314 0300B |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Clamp - ES-0510 |
| Парткод: | 11 050 329 |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 8 025 276 |
| Деталь: | Spacer - Kgls-16rt |
| Парткод: | 11 050 296 |
| Деталь: | Connector - 25P |
| Парткод: | 11 022 447 |
| Деталь: | Harness:Manual Feed:Duplex |
| Парткод: | B209 5244 |
| Деталь: | Bracket:Connector:Manual Feed Unit |
| Парткод: | B090 5826 |
| Деталь: | Gear - 44Z |
| Парткод: | AB01 4050 |
| Деталь: | Cover:Fusing:Drive |
| Парткод: | B090 1162 |
| Деталь: | Gear - 27Z |
| Парткод: | AB01 1204 |
| Деталь: | Bracket:Fusing:Swivel |
| Парткод: | B090 1170 |
| Деталь: | Gear - 30Z |
| Парткод: | AB01 1203 |
| Деталь: | Bracket:Fusing:Drive |
| Парткод: | B090 1159 |
| Деталь: | Magnetic Clutch - 35z |
| Парткод: | B209 1186 |
| Деталь: | PCB:PCU |
| Парткод: | B209 5156 |
| Деталь: | Lever:Dcsol:Assy |
| Парткод: | B209 1164 |
| Деталь: | Bracket:Harness |
| Парткод: | B206 5824 |
| Деталь: | Bracket:Connecting:Paper Feed |
| Парткод: | B209 1183 |
| Деталь: | Bracket:Temsion |
| Парткод: | B090 1115 |
| Деталь: | Timing Pulley - 31/36T |
| Парткод: | B090 1111 |
| Деталь: | Timing Belt - S3M - 342 |
| Парткод: | AA04 3516 |
| Деталь: | Gear Pulley - Registration |
| Парткод: | AB01 7625 |
| Деталь: | Gear - 35Z/28Z |
| Парткод: | AB01 7503 |
| Деталь: | Timing Belt - S3M - 225 |
| Парткод: | AA04 3515 |
| Деталь: | Timing Pulley - 27T/48T |
| Парткод: | AB03 3092 |
| Деталь: | Timing Belt - S3M - 420 |
| Парткод: | AA04 3514 |
| Деталь: | Spring:Tension |
| Парткод: | B091 2615 |
| Деталь: | Shoulder Screw - M3x2.5 |
| Парткод: | G020 5829 |
| Деталь: | Gear - Joint Paper Feed |
| Парткод: | AB01 7522 |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 8 025 276 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Connector - 54111-1615 |
| Парткод: | 11 027 672 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | Tapping Screw With Washer - M3x8 |
| Парткод: | 8 025 279 |
| Деталь: | O/O MB6 |
| Парткод: | B209 3001 |
| Деталь: | PCU Unit |
| Парткод: | B205 0151 |
| Деталь: | Pickoff Pawl |
| Парткод: | B039 2335 |
| Деталь: | Blade:Cleaning |
| Парткод: | AD04 1114 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3444 |
| Деталь: | Roller:Charge:A3 |
| Парткод: | AD02 7018 |
| Деталь: | Charge Cleaner Brush Roller |
| Парткод: | AD04 2058 |
| Деталь: | Charge Roller Spring |
| Парткод: | B039 2287 |
| Деталь: | Front Pressure Arm - Charge Roller |
| Парткод: | B039 2292 |
| Деталь: | Pin - Front Pressure Arm |
| Парткод: | B039 2293 |
| Деталь: | Arm:Pressure:Charge:Rear |
| Парткод: | B209 3174 |
| Деталь: | Electrode Plate:Roller:Charge:Assy |
| Парткод: | B209 3175 |
| Деталь: | Clip - OPC DRUM |
| Парткод: | B039 2350 |
| Деталь: | Joint:Development |
| Парткод: | B209 3440 |
| Деталь: | OPC Drum |
| Парткод: | B039 9510 |
| Деталь: | Development Roller Assembly |
| Парткод: | B209 3320 |
| Деталь: | Idler Gear |
| Парткод: | B039 3062 |
| Деталь: | Development Roller Gear |
| Парткод: | B039 3060 |
| Деталь: | Development Case |
| Парткод: | B209 3370 |
| Деталь: | Shield:Toner Supply:Entrance |
| Парткод: | B209 3196 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Binding Self-tapping Screw:3x6 |
| Парткод: | 0452 3006N |
| Деталь: | Bracket:Guide Plate:No.2 |
| Парткод: | B090 2587 |
| Деталь: | Cushion - Link |
| Парткод: | AA16 1143 |
| Деталь: | Bracket:Paper End Sensor |
| Парткод: | B090 2805 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Harness:Paper End Sensor:Connecting |
| Парткод: | B209 5215 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A267 2751 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | A267 2803 |
| Деталь: | Torsion Spring:Grip:Shaft:Lock |
| Парткод: | B091 2788 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | A267 2754 |
| Деталь: | Bracket:Photointerruptor |
| Парткод: | B090 2663 |
| Деталь: | Photointerruptor:Vertical Transport |
| Парткод: | AW02 0173 |
| Деталь: | Snap Ring |
| Парткод: | B090 2686 |
| Деталь: | Bracket:Roller:Guide:No.2 |
| Парткод: | B206 2577 |
| Деталь: | Roller:Sponge |
| Парткод: | B209 2665 |
| Деталь: | Roller:Drive:Upper:Rp2 |
| Парткод: | B097 2682 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0252 |
| Деталь: | Guide Plate:Friction Pad:Upper |
| Парткод: | B206 2828 |
| Деталь: | Bracket:Paper Size Sensor |
| Парткод: | B090 2873 |
| Деталь: | Push Switch - Paper Size |
| Парткод: | G020 2620 |
| Деталь: | Lever:Lock:Paper Feed Roller |
| Парткод: | B090 2792 |
| Деталь: | Tension Spring:Shaft:Lock |
| Парткод: | B091 2787 |
| Деталь: | Bushing - Motor Shaft |
| Парткод: | A267 2847 |
| Деталь: | Lock Lever Shaft - Feed Roller |
| Парткод: | A267 2785 |
| Деталь: | Bushing Paper Feed Roller |
| Парткод: | A267 2758 |
| Деталь: | Guide Plate:Paper Feed Roller:1 |
| Парткод: | B090 2800 |
| Деталь: | Roller Clutch-vertical Trans Port |
| Парткод: | B027 2681 |
| Деталь: | Torsion Spring - Lock Feed Roller |
| Парткод: | B091 2788 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11 050 522 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 8 053 480 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Harness Clamp - RLMC-05TV0 |
| Парткод: | 11 050 501 |
| Деталь: | Screw:Polished Round:M3x4 |
| Парткод: | 0951 3004N |
| Деталь: | Operation Panel:NA |
| Парткод: | B209 7152 |
| Деталь: | Operation Panel:EU |
| Парткод: | B209 7172 |
| Деталь: | Operation Panel ASIA |
| Парткод: | B209 7212 |
| Деталь: | Cover:Lower |
| Парткод: | B206 1432 |
| Деталь: | Cover:Lower:EU |
| Парткод: | B090 7032 |
| Деталь: | Cover:Blank:Fax:Coupling |
| Парткод: | B090 1448 |
| Деталь: | Harness:OP-R13 |
| Парткод: | B209 1453 |
| Деталь: | LCD:HVGA:SH:BL |
| Парткод: | B213 5225 |
| Деталь: | Cover:Upper:NA |
| Парткод: | B206 7160 |
| Деталь: | Cover:Upper:EU |
| Парткод: | B090 7031 |
| Деталь: | Keytop:Try Print |
| Парткод: | B090 1435 |
| Деталь: | Keytop - Preheat |
| Парткод: | B027 1439 |
| Деталь: | Keytop - Confirm |
| Парткод: | B027 1440 |
| Деталь: | Keytop:Block Diagram |
| Парткод: | B090 1441 |
| Деталь: | Keytop:Counter |
| Парткод: | B090 1442 |
| Деталь: | Keytop - Start |
| Парткод: | B027 1433 |
| Деталь: | Keytop - Interrupt |
| Парткод: | B027 1438 |
| Деталь: | Keytop:Blank:Left |
| Парткод: | B090 1449 |
| Деталь: | Keytop:Clear/Stop |
| Парткод: | B090 1434 |
| Деталь: | Keytop:10key:NA |
| Парткод: | B090 7161 |
| Деталь: | Keytop:10key (EU) |
| Парткод: | B090 1437 |
| Деталь: | Keytop - 10key (TWN) |
| Парткод: | B027 7214 |
| Деталь: | DIAL |
| Парткод: | B090 1444 |
| Деталь: | Keytop:Reset Switch:EXP |
| Парткод: | B090 7162 |
| Деталь: | PCB:OP-R |
| Парткод: | B209 1450 |
| Деталь: | PCB:OP-L |
| Парткод: | B209 1460 |
| Деталь: | Right Sheet - Operation Panel |
| Парткод: | B027 1482 |
| Деталь: | Left Sheet - Operation Panel |
| Парткод: | B027 1483 |
| Деталь: | Long Spacer - Touch Panel |
| Парткод: | B027 1484 |
| Деталь: | Short Spacer - Touch Panel |
| Парткод: | B027 1485 |
| Деталь: | Shadeing Plate |
| Парткод: | B027 1487 |
| Деталь: | Bracket:LCDC:EXP:Assy |
| Парткод: | B090 1496 |
| Деталь: | PCB:LCDC:NA:Assy |
| Парткод: | B209 5066 |
| Деталь: | PCB:LCDC:EU:Assy |
| Парткод: | B209 5067 |
| Деталь: | PCB:LCDC:TWN:Assy |
| Парткод: | B209 5068 |
| Деталь: | Cap - LED Data/In |
| Парткод: | B027 1493 |
| Деталь: | Harness:OP-R10 |
| Парткод: | B209 1454 |
| Деталь: | Sheet - Power Source Display |
| Парткод: | B027 7164 |
| Деталь: | Sheet:Power Source:Display:EU |
| Парткод: | B093 7184 |
| Деталь: | Touch Panel:HVGA (NA) |
| Парткод: | B213 5222 |
| Деталь: | Touch Panel:HVGA (EU/Asia) |
| Парткод: | B180 5258 |
| Деталь: | LED Display Sheet |
| Парткод: | B027 7163 |
| Деталь: | Keytop:Main Switch |
| Парткод: | B090 1436 |
| Деталь: | Front Left Lens |
| Парткод: | B027 1445 |
| Деталь: | Upper Left Sheet |
| Парткод: | B027 1495 |
| Деталь: | Harness:OP-L14 |
| Парткод: | B209 1463 |
| Деталь: | Harness:OP-L15 |
| Парткод: | B209 1464 |
| Деталь: | Binding Self-tapping Screw:3x10 |
| Парткод: | 0452 3010N |
| Деталь: | Binding Self-tapping Screw:M3x14 |
| Парткод: | 0452 3014N |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Platen Cover Sheet |
| Парткод: | 54 482 804 |
| Деталь: | Platen Cover Pad |
| Парткод: | B406 1393 |
| Деталь: | Flex Hinge - Platen Cover |
| Парткод: | G329 1350 |
| Деталь: | Front Platen Cover |
| Парткод: | B406 1387 |
| Деталь: | ORIGINAL HOLDER |
| Парткод: | B406 1397 |
| Деталь: | Rear Platen Cover |
| Парткод: | B406 1392 |
| Деталь: | Hinge:Pressure Plate:Assy |
| Парткод: | G329 1355 |
| Деталь: | Feeler - Platen Cover |
| Парткод: | B406 1384 |
| Деталь: | Screw - M4 |
| Парткод: | A548 6121 |
| Деталь: | Bracket - Platen Cover |
| Парткод: | B484 1383 |
| Деталь: | Tapping Scrwe:4x12 |
| Парткод: | 0450 4012N |
| Деталь: | Energy Decal |
| Парткод: | GA00 3035 |
| Деталь: | Hinge - Front Cover |
| Парткод: | G020 1332 |
| Деталь: | Magnet Catch:Door:Front |
| Парткод: | B090 1264 |
| Деталь: | Sheet Emblem - EXP (B205) |
| Парткод: | B205 7060 |
| Деталь: | Sheet Emblem - GES (B205) |
| Парткод: | B205 7063 |
| Деталь: | Sheet Emblem - LAN (B205) |
| Парткод: | B205 7064 |
| Деталь: | Sheet Emblem - INF (B205) |
| Парткод: | B205 7068 |
| Деталь: | Sheet Emblem - EXP (B209) |
| Парткод: | B209 7060 |
| Деталь: | Sheet Emblem - GES (B209) |
| Парткод: | B209 7063 |
| Деталь: | Sheet Emblem - LAN (B209) |
| Парткод: | B209 7064 |
| Деталь: | Sheet:Emblem:Ric:2510 (D007) |
| Парткод: | D007 7061 |
| Деталь: | Sheet:Emblem:INF (D007) |
| Парткод: | D007 7068 |
| Деталь: | Sheet:Emblem:LAN:2510 (D007) |
| Парткод: | D007 7069 |
| Деталь: | Sheet:Emblem:GES:2510:AA (D007) |
| Парткод: | D007 7070 |
| Деталь: | Sheet:Emblem:Ric:3010 (D008) |
| Парткод: | D008 7061 |
| Деталь: | Sheet:Emblem:INF (D008) |
| Парткод: | D008 7068 |
| Деталь: | Sheet:Emblem:LAN:3010 (D008) |
| Парткод: | D008 7069 |
| Деталь: | Sheet:Emblem:GES:3010:AA (D008) |
| Парткод: | D008 7070 |
| Деталь: | Cover:Main Switch |
| Парткод: | B090 1302 |
| Деталь: | Door:Front:NA:Assy |
| Парткод: | B209 7051 |
| Деталь: | Door:Front:EU:Assy |
| Парткод: | B209 7071 |
| Деталь: | Cover:Paper Exit Sub-unit:Left |
| Парткод: | B209 1341 |
| Деталь: | Cover:Paper Exit Sub-unit:Left:EU |
| Парткод: | B209 7026 |
| Деталь: | END FENCE |
| Парткод: | B090 1343 |
| Деталь: | PAPER EXIT TRAY |
| Парткод: | B024 1348 |
| Деталь: | Paper Exit Cover EU Assy |
| Парткод: | B209 7025 |
| Деталь: | Paper Exit Cover NA Assy |
| Парткод: | B209 1340 |
| Деталь: | Panel:Logo |
| Парткод: | B132 1531 |
| Деталь: | Cover:Front:Right Upper |
| Парткод: | B091 1320 |
| Деталь: | Cover:Front:Right Upper:EU |
| Парткод: | B091 7023 |
| Деталь: | Cover:Front |
| Парткод: | B209 1324 |
| Деталь: | Cover:Front:EU |
| Парткод: | B209 7024 |
| Деталь: | Magnet Catch:44.1n |
| Парткод: | AG07 0504 |
| Деталь: | Operation Instructions Sheet |
| Парткод: | B027 1268 |
| Деталь: | Shield Duct |
| Парткод: | A267 1342 |
| Деталь: | Cover:Paper Exit:Upper Left:EU |
| Парткод: | B091 7022 |
| Деталь: | Cover:Paper Exit Sub-unit:Upper Left |
| Парткод: | B206 1306 |
| Деталь: | Cap - LED |
| Парткод: | A267 1325 |
| Деталь: | Guide Plate:Scanner:Packing |
| Парткод: | B090 1099 |
| Деталь: | PCU Unit |
| Парткод: | B205 0151 |
| Деталь: | Cover:Shield Glass:C |
| Парткод: | B090 1265 |
| Деталь: | Decal:Power Source:Off:Exp |
| Парткод: | B082 6403 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Grounding Plate - Regist Roller |
| Парткод: | A267 2695 |
| Деталь: | Guide Plate:PCU |
| Парткод: | B209 1051 |
| Деталь: | PCU Seal |
| Парткод: | A267 1059 |
| Деталь: | Discharge Lamp |
| Парткод: | B209 3452 |
| Деталь: | Bushing - Registration Roller |
| Парткод: | A267 2674 |
| Деталь: | Snap Ring |
| Парткод: | B090 2686 |
| Деталь: | Harness:Registration Sensor |
| Парткод: | B209 5237 |
| Деталь: | Guide Plate:Entrance:Upper |
| Парткод: | B090 2745 |
| Деталь: | Cushion - Link |
| Парткод: | AA16 1143 |
| Деталь: | Guide Plate:Entrance:Upper Right |
| Парткод: | B090 2747 |
| Деталь: | Guide Plate:Registration:Left:Assy |
| Парткод: | B209 2690 |
| Деталь: | Cushion:Upper |
| Парткод: | B209 2748 |
| Деталь: | Registration Roller:Drive |
| Парткод: | B206 2720 |
| Деталь: | Snap Ring - M6 |
| Парткод: | B090 2621 |
| Деталь: | Roller:Sponge |
| Парткод: | B209 2665 |
| Деталь: | Pegistration Sensor |
| Парткод: | AW01 0057 |
| Деталь: | Bracket:Registration Sensor |
| Парткод: | B090 2698 |
| Деталь: | Cleaner:Registration:No.2:Assy |
| Парткод: | B209 2725 |
| Деталь: | Guide Plate:Entrance:Upper |
| Парткод: | A267 2743 |
| Деталь: | Guide Plate:Registration:Lower |
| Парткод: | A267 2723 |
| Деталь: | Guide Plate:Entrance:Upper:Assy |
| Парткод: | B209 2741 |
| Деталь: | Binding Self-tapping Screw:3x10 |
| Парткод: | 0452 3010N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | CLAMP |
| Парткод: | 11 050 283 |
| Деталь: | CLAMP |
| Парткод: | 11 050 460 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 8 053 480 |
| Деталь: | Harness:Scanner |
| Парткод: | B209 5230 |
| Деталь: | Original Sensor:H2-66 |
| Парткод: | AW01 0126 |
| Деталь: | Harness:SBU |
| Парткод: | B209 5245 |
| Деталь: | 1st Mirror Holder |
| Парткод: | A193 1767 |
| Деталь: | Carriage:No.1:Assy |
| Парткод: | B090 1670 |
| Деталь: | Wire Clamp |
| Парткод: | A193 1766 |
| Деталь: | Xenon Lamp - 8.5MM |
| Парткод: | AX50 0077 |
| Деталь: | Lens Unit |
| Парткод: | B209 1673 |
| Деталь: | 1st Mirror |
| Парткод: | A250 1784 |
| Деталь: | Clamp - Rear Wire |
| Парткод: | A193 1769 |
| Деталь: | Harness Guide - Exposure Lamp |
| Парткод: | A267 1758 |
| Деталь: | Flexible Board |
| Парткод: | B209 5227 |
| Деталь: | Flexible Board Bracket |
| Парткод: | B027 1808 |
| Деталь: | Stabilizer:Xenon Lamp |
| Парткод: | AZ50 0068 |
| Деталь: | Lens Block Holder |
| Парткод: | B027 1811 |
| Деталь: | Base:Scanner:Assy MB7 DLETED |
| Парткод: | B209 1801 |
| Деталь: | Original Sensor:H1-66 |
| Парткод: | AW01 0125 |
| Деталь: | Ground Plate:Block:Lens |
| Парткод: | B027 1809 |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 8 025 276 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | PCB Stud |
| Парткод: | 11 050 195 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | CLAMP |
| Парткод: | 11 050 460 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Power Pack:BCTD |
| Парткод: | AZ32 0146 |
| Деталь: | Receptacle Charge |
| Парткод: | B209 3461 |
| Деталь: | Receptacle |
| Парткод: | B209 3950 |
| Деталь: | Harness:Document Feeder |
| Парткод: | B209 5242 |
| Деталь: | Guide Plate:Fusing Unit:Rear:C |
| Парткод: | B090 1076 |
| Деталь: | Harness:AC:Fusing:NA |
| Парткод: | B209 7612 |
| Деталь: | Harness:AC:Fusing:EU |
| Парткод: | B209 7632 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3301 |
| Деталь: | Harness:Power Source:Joint Unit:R-C |
| Парткод: | B209 5235 |
| Деталь: | Brushless Motor:24V/28W |
| Парткод: | B209 1129 |
| Деталь: | Harness:High Voltage Line:B:R-C |
| Парткод: | B209 5218 |
| Деталь: | Fly Wheel |
| Парткод: | B090 1184 |
| Деталь: | Spacer - KGLS-12RF |
| Парткод: | G020 5871 |
| Деталь: | Bracket:Power Pack |
| Парткод: | B090 5833 |
| Деталь: | Stand:IOB:Upper |
| Парткод: | B206 5839 |
| Деталь: | Stand:IOB:Lower |
| Парткод: | B090 5840 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 8 025 276 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008H |
| Деталь: | CLAMP |
| Парткод: | 11 050 460 |
| Деталь: | CLAMP |
| Парткод: | 11 050 352 |
| Деталь: | Philips Screw With Flat Washer-M3x8 |
| Парткод: | 0951 3008B |
| Деталь: | Support Spacer - M3x29 |
| Парткод: | 11 050 499 |
| Деталь: | Harness Clamp - IWS-2218 |
| Парткод: | 11 050 490 |
| Деталь: | Edge - 17 |
| Парткод: | 11 050 334 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | CLAMP |
| Парткод: | 11 050 283 |
| Деталь: | Paper Tray:1:Assy |
| Парткод: | B209 7353 |
| Деталь: | Paper Tray:2:Assy |
| Парткод: | B209 7354 |
| Деталь: | Paper Set Decal |
| Парткод: | B027 2892 |
| Деталь: | Side Fence:Front:Assy |
| Парткод: | B090 2884 |
| Деталь: | Decal:Paper Size Sensor Board:EXP |
| Парткод: | B024 7347 |
| Деталь: | Lever:Stopper:Front |
| Парткод: | B090 2858 |
| Деталь: | Slider:Base |
| Парткод: | B090 2874 |
| Деталь: | END FENCE |
| Парткод: | B090 2853 |
| Деталь: | Seal - End Fence |
| Парткод: | A267 2900 |
| Деталь: | Slider:Upper |
| Парткод: | B090 2866 |
| Деталь: | Tray Bottom Plate:Assy |
| Парткод: | B090 2861 |
| Деталь: | Bracket:Rise |
| Парткод: | B090 2856 |
| Деталь: | Decal - Side Fence |
| Парткод: | B027 7352 |
| Деталь: | Lever:Stopper:Positioning |
| Парткод: | B090 2860 |
| Деталь: | Stopper:Positioning |
| Парткод: | B090 2859 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Decal - Paper Size Select |
| Парткод: | B090 2961 |
| Деталь: | Side Fence:Inner Back:Assy |
| Парткод: | B090 2885 |
| Деталь: | Shaft - Tray Raising |
| Парткод: | A267 2854 |
| Деталь: | Friction Pad:Stinger:Adhesion |
| Парткод: | B390 2831 |
| Деталь: | Friction pad |
| Парткод: | A267 2831 |
| Деталь: | Pressure Spring - Friction Pad |
| Парткод: | A267 2834 |
| Деталь: | Paper Size Sensor:1:EXP |
| Парткод: | B090 7345 |
| Деталь: | Shaft - Roller |
| Парткод: | A267 2865 |
| Деталь: | Spring Plate:Paper Size Sensor:Assy |
| Парткод: | B209 2870 |
| Деталь: | Roller:Bracket:Rise |
| Парткод: | B090 2864 |
| Деталь: | Sheet:Holder:Paper Tray |
| Парткод: | B091 2898 |
| Деталь: | Damping Insulation Paper Tray |
| Парткод: | B209 2913 |
| Деталь: | PAPER TRAY |
| Парткод: | B090 2850 |
| Деталь: | Shield - Side Fence |
| Парткод: | A267 2897 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | G697 2677 |
| Деталь: | Spring Plate - Slider |
| Парткод: | A267 2875 |
| Деталь: | Roller:Paper Tray |
| Парткод: | B090 2987 |
| Деталь: | Gear - 16Z |
| Парткод: | B090 2869 |
| Деталь: | Spring Plate - Grounding |
| Парткод: | A267 2878 |
| Деталь: | Sponge - Paper Feed Tray |
| Парткод: | A267 2899 |
| Деталь: | BASE PAD |
| Парткод: | A267 2917 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0450 4008N |
| Деталь: | Spacer - 12.7mm |
| Парткод: | 11 050 415 |
| Деталь: | Screw-m4x6 |
| Парткод: | 0354 0060N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 083 |
| Деталь: | Shadeing Plate:Ctl:Assy |
| Парткод: | B209 5874 |
| Деталь: | Panel:Fax:Option |
| Парткод: | B209 5869 |
| Деталь: | Cover:FFC:Image Processing Unit |
| Парткод: | B209 5853 |
| Деталь: | PCB:DDR-DIMM:128MB |
| Парткод: | B584 5040 |
| Деталь: | Controller Board 25CPM (B205) |
| Парткод: | B215 5305 |
| Деталь: | Controller Board 30CPM (B209) |
| Парткод: | B215 5306 |
| Деталь: | Controller Board C4.5 25CPM (D007) |
| Парткод: | D006 5305 |
| Деталь: | Controller Board C4.5 30CPM (D008) |
| Парткод: | D006 5306 |
| Деталь: | Bracket:Image Processing Unit |
| Парткод: | B209 5850 |
| Деталь: | Panel:Interface |
| Парткод: | B209 5867 |
| Деталь: | Rack:Application:Upper |
| Парткод: | B209 5855 |
| Деталь: | Rack:Application:Lower |
| Парткод: | B209 5860 |
| Деталь: | Bracket:Control Board |
| Парткод: | B209 5866 |
| Деталь: | PCB:Image Processing Unit |
| Парткод: | B209 5125 |
| Деталь: | Harness - Laser Diode Control |
| Парткод: | B027 5223 |
| Деталь: | Harness:SBU |
| Парткод: | B209 5245 |
| Деталь: | Harness:IPU |
| Парткод: | B209 5221 |
| Деталь: | Right Rail |
| Парткод: | B070 5670 |
| Деталь: | Left Rail |
| Парткод: | B070 5671 |
| Деталь: | Harness:Laser Diode Control |
| Парткод: | B209 5223 |
| Деталь: | Harness:Scanner |
| Парткод: | B209 5230 |
| Деталь: | HARNESS:SENSOR |
| Парткод: | B209 5239 |
| Деталь: | IPU Harness Bracket |
| Парткод: | B209 5854 |
| Деталь: | Harness:Door Switch:Front |
| Парткод: | B209 5204 |
| Деталь: | Harness:Power Supply Unit |
| Парткод: | B209 5212 |
| Деталь: | NVRAM - Zero Counter (B205/B209) |
| Парткод: | B195 9590 |
| Деталь: | NVRAM - Zero Counter (D007/D008) |
| Парткод: | D007 9590 |
| Деталь: | PCB:DDR-DIMM:256MB:Assy (Option) |
| Парткод: | B585 5030 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw:Round Point:M3x6 |
| Парткод: | 8 025 291 |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | WIRE SADDLE |
| Парткод: | 11 050 292 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Shutter Lever |
| Парткод: | B024 3931 |
| Деталь: | Compression Spring - 24n:Rear |
| Парткод: | B091 2673 |
| Деталь: | Separation Unit:Assy |
| Парткод: | B209 3831 |
| Деталь: | Spring Plate - Band Stopper |
| Парткод: | A232 3962 |
| Деталь: | Band - Vertical Transport Cover |
| Парткод: | A267 3941 |
| Деталь: | Cover:Transfer/separation Unit (NA) |
| Парткод: | B209 3821 |
| Деталь: | Cover:Transfer/separation Unit (EU) |
| Парткод: | B209 3822 |
| Деталь: | Cover:Right (NA/TWN) |
| Парткод: | B090 3857 |
| Деталь: | Cover:Right:EU |
| Парткод: | B090 7055 |
| Деталь: | Decal - Right Cover |
| Парткод: | B024 3858 |
| Деталь: | ID SENSOR |
| Парткод: | A267 9007 |
| Деталь: | Compression Spring:Pressure:Front |
| Парткод: | B091 3911 |
| Деталь: | Compression Spring - 24n:Front |
| Парткод: | B091 2672 |
| Деталь: | Front Bushing - Transfer Roller |
| Парткод: | AA08 0256 |
| Деталь: | Bushing - Driven Roller |
| Парткод: | A267 2685 |
| Деталь: | Guide Plate:Registration:Right:C2 |
| Парткод: | B092 2711 |
| Деталь: | Cleaner - Regist Driven Roller |
| Парткод: | A267 2712 |
| Деталь: | Grounding Terminal |
| Парткод: | A267 3921 |
| Деталь: | Rear Bushing - Transfer Roller |
| Парткод: | AA08 0250 |
| Деталь: | Transfer/Separation Lever |
| Парткод: | B024 3871 |
| Деталь: | Compression Spring:Lever |
| Парткод: | B091 3872 |
| Деталь: | Terminal - Separation |
| Парткод: | A267 3862 |
| Деталь: | Terminal - Transfer Roller |
| Парткод: | A267 3861 |
| Деталь: | Compression Spring:Pressure:Rear |
| Парткод: | B091 3912 |
| Деталь: | Guide Mylar |
| Парткод: | A267 2744 |
| Деталь: | Rear Discharge Sheet |
| Парткод: | AA15 0709 |
| Деталь: | Registration Driven Roller -rp2 |
| Парткод: | AF02 1066 |
| Деталь: | Front Discharge Sheet |
| Парткод: | AA15 0708 |
| Деталь: | Cover - ID Sensor |
| Парткод: | A267 3905 |
| Деталь: | Decal-Jam Removal-Right Cover |
| Парткод: | B090 4460 |
| Деталь: | Decal - B |
| Парткод: | B090 4461 |
| Деталь: | Protection Sheet - Handle |
| Парткод: | B154 1325 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Cover:Paper Exit Sub-unit:Rear Left |
| Парткод: | B206 1304 |
| Деталь: | Rear Left Cover - Paper Feed:EU |
| Парткод: | B093 7021 |
| Деталь: | Cover:Left |
| Парткод: | B091 1281 |
| Деталь: | Cover:Left:Eu |
| Парткод: | B091 7017 |
| Деталь: | Cover:Left Rear |
| Парткод: | B209 1282 |
| Деталь: | Cover:Left Rear:EU |
| Парткод: | B209 7018 |
| Деталь: | Cover:Left Upper |
| Парткод: | B091 1280 |
| Деталь: | Cover:Left Upper:EU |
| Парткод: | B091 7016 |
| Деталь: | Cover:Scanner:Rear Upper |
| Парткод: | B091 1251 |
| Деталь: | Cover:Scanner:Rear Upper:EU |
| Парткод: | B091 7011 |
| Деталь: | Cap - 38x77 |
| Парткод: | B024 1365 |
| Деталь: | Rivet - M7 |
| Парткод: | B039 1364 |
| Деталь: | Cap:Paper Feed Table |
| Парткод: | B090 1374 |
| Деталь: | Cap:Paper Feed Table:EU |
| Парткод: | B090 7028 |
| Деталь: | Cap:Duplex:Connector |
| Парткод: | B090 1371 |
| Деталь: | Cover - Right Rear |
| Парткод: | B209 2717 |
| Деталь: | Cover:Paper Feed Sub-unit:Right Rear:Assy |
| Парткод: | B209 7036 |
| Деталь: | Stay:Cap |
| Парткод: | B090 2710 |
| Деталь: | Cap:Manual Feed Unit (NA) |
| Парткод: | B090 2708 |
| Деталь: | Cap:Manual Feed Unit (EU) |
| Парткод: | B090 7043 |
| Деталь: | Hexagonal Set Screw - M3x8 |
| Парткод: | A267 2713 |
| Деталь: | Operation Panel:NA |
| Парткод: | B209 7152 |
| Деталь: | Operation Panel:EU |
| Парткод: | B209 7172 |
| Деталь: | Paper Feed Cover:Right:Middle |
| Парткод: | B209 2727 |
| Деталь: | Paper Feed Cover:Right:Middle:EU |
| Парткод: | B144 7007 |
| Деталь: | Cover - Right Front |
| Парткод: | B209 2716 |
| Деталь: | Cover:Paper Exit Sub-unit:Lower |
| Парткод: | B091 1345 |
| Деталь: | Cover:Paper Exit:Lower:EU |
| Парткод: | B091 7027 |
| Деталь: | Guide Mylar |
| Парткод: | A267 2709 |
| Деталь: | Shield - 3x5x85 |
| Парткод: | B209 2642 |
| Деталь: | Shield - 3x10x363 |
| Парткод: | B209 2647 |
| Деталь: | Shield - 3x5x70 |
| Парткод: | B209 2643 |
| Деталь: | Cover:Paper Feed Unit:Right:Middle |
| Парткод: | B090 2705 |
| Деталь: | Cover:Paper Feed Unit:Right:Middle:EU |
| Парткод: | B090 7041 |
| Деталь: | Compression Spring - 10n |
| Парткод: | B091 2739 |
| Деталь: | BUSHING - VERTICAL TRANSPORT |
| Парткод: | AA08 0249 |
| Деталь: | Roller:Driven |
| Парткод: | B090 2715 |
| Деталь: | Cap:Duplex |
| Парткод: | B090 1370 |
| Деталь: | Cover:Right |
| Парткод: | B206 1270 |
| Деталь: | Cover:Right:EU |
| Парткод: | B091 7015 |
| Деталь: | Cover:Paper Feed Sub-unit:Rear |
| Парткод: | B091 1291 |
| Деталь: | Cover:Paper Feed Sub-unit:Rear:EU |
| Парткод: | B091 7020 |
| Деталь: | RIVET |
| Парткод: | B039 1363 |
| Деталь: | Cap:Heater:Dehumidifier |
| Парткод: | B090 1375 |
| Деталь: | Cover:Scanner:Right |
| Парткод: | B206 1252 |
| Деталь: | Cover:Scanner:Right:EU |
| Парткод: | B091 7012 |
| Деталь: | Cover:Rear |
| Парткод: | B209 1290 |
| Деталь: | Cover:Rear:EU |
| Парткод: | B209 7019 |
| Деталь: | Cover:Scanner:Left |
| Парткод: | B206 1250 |
| Деталь: | Cover:Scanner:Left:EU |
| Парткод: | B091 7010 |
| Деталь: | Screw - M4x5 |
| Парткод: | B206 2945 |
| Деталь: | Protection Sheet - Handle |
| Парткод: | B154 1325 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | DC Motor:Paper Feed:Assy |
| Парткод: | AX04 0220 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Bushing - 8x16x7 |
| Парткод: | AA08 2070 |
| Деталь: | Bracket:Rise:2 |
| Парткод: | B090 2773 |
| Деталь: | Cover:Right Inner Rear |
| Парткод: | B090 2592 |
| Деталь: | Rising Unit:Assy |
| Парткод: | B209 2780 |
| Деталь: | Pressure Lever Stopper |
| Парткод: | B024 2765 |
| Деталь: | Tension Spring:Stopper:Return |
| Парткод: | B091 2766 |
| Деталь: | Cover:Left Inner Rear |
| Парткод: | B090 2593 |
| Деталь: | Bracket:Power Supply Cord |
| Парткод: | B090 5831 |
| Деталь: | Bracket:Holder:Paper Tray |
| Парткод: | B090 2908 |
| Деталь: | Tray Holder |
| Парткод: | G697 1082 |
| Деталь: | Bracket:Guard:Harness:Heater |
| Парткод: | B090 2916 |
| Деталь: | Holder - Spring |
| Парткод: | A267 2846 |
| Деталь: | Compression Spring:Return |
| Парткод: | B091 2844 |
| Деталь: | Bushing - DC Motor Shaft |
| Парткод: | A267 2845 |
| Деталь: | Bracket:DC Motor:2 |
| Парткод: | B090 2838 |
| Деталь: | Shaft - DC Motor |
| Парткод: | A267 2840 |
| Деталь: | Clip:Shaft |
| Парткод: | B031 2836 |
| Деталь: | Tension Spring:Pressure:Main |
| Парткод: | B207 2771 |
| Деталь: | Tension Spring:Pressure:Sub |
| Парткод: | B207 2773 |
| Деталь: | Torsion Spring:Joint:Return |
| Парткод: | B091 2767 |
| Деталь: | Lever:Rise:Paper Volume Sensor |
| Парткод: | B090 2777 |
| Деталь: | Vibrating Plate |
| Парткод: | A267 2770 |
| Деталь: | Bracket:Rise:1 |
| Парткод: | B090 2815 |
| Деталь: | Guard:Spring:Paper Feed |
| Парткод: | B090 2595 |
| Деталь: | Harness Cover - Paper Feed |
| Парткод: | B024 2839 |
| Деталь: | Bracket:DC Motor:1 |
| Парткод: | B090 2837 |
| Деталь: | Bushing - Motor Shaft |
| Парткод: | A267 2847 |
| Деталь: | Lever:DC Motor |
| Парткод: | B090 2776 |
| Деталь: | Stopper:Holder:Compression Spring |
| Парткод: | B090 2848 |
| Деталь: | Shutter - Photointerruptor |
| Парткод: | A267 2849 |
| Деталь: | Sub Pressure Lever |
| Парткод: | A267 2794 |
| Деталь: | Bracket:Lever:Pressure |
| Парткод: | B090 2781 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw:3x30 |
| Парткод: | 0451 3030N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Philips Screw - M4x8 |
| Парткод: | 8 010 150 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | WIRE SADDLE |
| Парткод: | 11 050 292 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 8 025 276 |
| Деталь: | Clamp - ES-0510 |
| Парткод: | 11 050 329 |
| Деталь: | CLAMP |
| Парткод: | 11 050 460 |
| Деталь: | TONER SUPPLY UNIT |
| Парткод: | B090 3501 |
| Деталь: | Cover:Toner Bottle:Assy |
| Парткод: | B090 3560 |
| Деталь: | Motor Spacer - Toner Bottle |
| Парткод: | B027 3620 |
| Деталь: | Toner Bottle Motor |
| Парткод: | B209 3616 |
| Деталь: | Bracket DC Motor Toner Bottle Z EXP |
| Парткод: | B090 7440 |
| Деталь: | Guide Plate:Toner Supply Unit |
| Парткод: | B090 1054 |
| Деталь: | Shaft:Slide |
| Парткод: | B259 3422 |
| Деталь: | Cam:Handle |
| Парткод: | B090 3605 |
| Деталь: | Shaft:Chuck |
| Парткод: | B090 3572 |
| Деталь: | Chuck Spring - Tonner Bottle |
| Парткод: | A267 3556 |
| Деталь: | Slider:Assy |
| Парткод: | B090 3573 |
| Деталь: | Chuck:Bottle |
| Парткод: | B090 3571 |
| Деталь: | Tapping Screw-M3x8 |
| Парткод: | B044 3191 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Front Pulley - Wire Drive |
| Парткод: | AB03 2066 |
| Деталь: | Wire:Scanner:Drive |
| Парткод: | AA05 0115 |
| Деталь: | Bracket:Tension:Fix |
| Парткод: | B090 1837 |
| Деталь: | Tension Spring:Tension |
| Парткод: | B091 1783 |
| Деталь: | Front Left Bracket - Idler |
| Парткод: | B024 1841 |
| Деталь: | Slide Rail - 2 |
| Парткод: | A267 1817 |
| Деталь: | 1st Slide Rail |
| Парткод: | A193 1816 |
| Деталь: | Scanner:No.2:Assy |
| Парткод: | B090 1767 |
| Деталь: | Mirror:No.3 |
| Парткод: | B206 1794 |
| Деталь: | MIRROR HOLDER |
| Парткод: | A267 1777 |
| Деталь: | Scanner Drive Shaft |
| Парткод: | B027 1825 |
| Деталь: | Anticondensation Heater - 120V |
| Парткод: | A267 8465 |
| Деталь: | Anticondensation Heater - 230V |
| Парткод: | A267 8466 |
| Деталь: | Timing Belt - ST1.5 249MM |
| Парткод: | AA04 3572 |
| Деталь: | Guide - FPC |
| Парткод: | A267 1776 |
| Деталь: | Guide - Flexible Board |
| Парткод: | A267 1816 |
| Деталь: | Insulating Sheet - Side Plate |
| Парткод: | A267 1819 |
| Деталь: | Rear Left Bracket - Idler |
| Парткод: | B024 1845 |
| Деталь: | Rear Pulley - Wire Drive |
| Парткод: | AB03 2067 |
| Деталь: | Tension Spring:7.5n |
| Парткод: | B091 1784 |
| Деталь: | Stepper Motor:Assy |
| Парткод: | B209 1690 |
| Деталь: | Guard:Drive Sub-unit |
| Парткод: | B090 1812 |
| Деталь: | Timing Pulley - 81 |
| Парткод: | AB03 0709 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | Hexagon Headless Set Screw - M5x5 |
| Парткод: | 0575 0050E |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0451 3006B |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 8 025 276 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | CLAMP |
| Парткод: | 11 050 460 |
| Деталь: | Screw - M3x8 |
| Парткод: | 0360 3008B |
| Деталь: | Ball Bearing - 8x16x5mm |
| Парткод: | 7 403 808 |
| Деталь: | Bracket:Paper End Sensor |
| Парткод: | B090 2805 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Harness:Paper End Sensor:Connecting |
| Парткод: | B209 5215 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A267 2751 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | A267 2803 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | A267 2754 |
| Деталь: | Bracket:Photointerruptor |
| Парткод: | B206 2660 |
| Деталь: | Photointerruptor:Vertical Transport |
| Парткод: | AW02 0173 |
| Деталь: | Roller:Drive |
| Парткод: | B097 2668 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0252 |
| Деталь: | Guide Plate:Friction Pad |
| Парткод: | B206 2842 |
| Деталь: | Bracket:Paper Size Sensor:No.2 |
| Парткод: | B090 2882 |
| Деталь: | Push Switch - Paper Size |
| Парткод: | G020 2620 |
| Деталь: | Stopper Paper Feed Roller |
| Парткод: | B093 2935 |
| Деталь: | Snap Ring |
| Парткод: | B090 2686 |
| Деталь: | Guide Plate Paper Feed Roller 2 Assy |
| Парткод: | B093 2808 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11 050 522 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 8 053 480 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Harness Clamp - RLMC-05TV0 |
| Парткод: | 11 050 501 |
| Деталь: | Roller - Lever |
| Парткод: | A267 3958 |
| Деталь: | Cover:Paper Feed Sensor |
| Парткод: | B090 4489 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | AA12 0094 |
| Деталь: | Shaft - Paper Overflow |
| Парткод: | A267 4479 |
| Деталь: | Stopper:Spring Plate:Outer |
| Парткод: | B091 4487 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | A267 4483 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0567 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0566 |
| Деталь: | Stopper:Spring Plate |
| Парткод: | B091 4486 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | A267 4474 |
| Деталь: | Feeler - Paper Overflow |
| Парткод: | A267 4478 |
| Деталь: | EXIT ROLLER |
| Парткод: | B209 4475 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1404 |
| Деталь: | Guide Plate:Exit |
| Парткод: | B090 4454 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Stopper - Right Upper Cover |
| Парткод: | A267 1349 |
| Деталь: | Cover:Paper Exit Sub-unit:Guide Plate |
| Парткод: | B209 1346 |
| Деталь: | Harness:Paper Exit Section |
| Парткод: | B209 5207 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Photointerruptor |
| Парткод: | B207 1886 |
| Деталь: | Feeler - Paper Feed Sensor |
| Парткод: | A267 4476 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 2112 |
| Деталь: | Stay:Exit |
| Парткод: | B090 4452 |
| Деталь: | Decal - C |
| Парткод: | B090 4462 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 8 053 480 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Tapping Screw:Round Point:M3x6 |
| Парткод: | 8 025 291 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 8 025 283 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
Коды ошибок
101
102
120
121
122
123
141
143
144
165
193
195
196
197
198
199
302
320
322
323
350
351
352
353
354
355
389
390
391
392
398
399
401
402
411
490
500
501
502
503
504
506
508
509
510
520
541
542
543
544
545
546
547
548
557
590
611
612
620
621
650
669
670
672
720
721
722
724
725
726
727
728
730
731
732
770
791
792
793
800
804
818
819
820
821
822
823
824
826
827
828
829
838
840
841
850
851
853
854
855
856
857
860
861
862
863
864
865
866
867
868
870
872
873
874
875
876
880
901
920
921
925
951
953
954
955
964
984
986
990
991
992
995
997
998
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 102 |
| Display: | Service Call 102: Error |
| Description: | Environmental Sensor Failure An error was detected in the Environmental Sensor circuitry. |
| Causes: | • Temp/Humidity Sensor, PL9.1.20 • TMP Harness, PL10.1.4 |
| Remedy: | 1 Test the Temperature/Humidity Sensor. Run the Service Diagnostics Temperature/ Humidity Sensor test. Does the sensor function correctly? Go to Step 2. Replace the Temp/ Hum Sensor. 2 Check the Humidity signal. Disconnect P/J231. Is the voltage across P/J231-2 <=> P/J231-3 less than +3 V and above +0.5 V. Go to Step 4. Go to Step 3. 3 Check the Temperature signal. Disconnect P/J231. Is the voltage across P/J231-4 <=> P/J231-3 greater than +2.5 V? Go to Step 4. Replace the Engine Control Board. 4 Check for +5 V to the Temperature/ Humidity Sensor. Disconnect P/J231. Is there +5 V across P/J231-1 <=> P/J231-3? Replace the Temp/ Hum Sensor. Replace the Engine Control Board. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 122 |
| Display: | Service Call 122: Error |
| Description: | Finisher Decurler Failure, Code 122 The level of the Decurler Cam Home Sensor did not change 4 seconds after the Decurler Cam Clutch has turned on. |
| Causes: | • Decurler Cam Clutch • Stacker Motor • Finisher Control Board |
| Remedy: | 1 1. Rotate the actuator while running the Decurler Cam Position test in diagnostics. 2. Does the value change between H and L? Go to step 2. Troubleshoot using the transmissive sensor procedure. 2 Does the decurler cam clutch operate in diagnostics? Check for a mechanical problem with the decurler cam clutch drive. If no problem is found replace the clutch. Go to step 3. 3 Is +24 VDC present at P/J 849-1? Replace the decurler cam clutch. Go to step 4. 4 Is +24 VDC present at test point 5 on the finisher control board? Replace the finisher control board. Troubleshoot the +24 VDC interlock circuit. 5 Is +24 VDC present at P/J 847-11 with the Finisher Stacker Motor Down test running in diagnostics? Replace the stacker motor. Replace the finisher control board |
| Error code: | 123 |
| Display: | Service Call 123: Error |
| Description: | Finisher Set Clamp Failure, Code 123 The set clamp home sensor did not turn on within 2 seconds after the set clamp started operation. |
| Causes: | • Set Clamp Solenoid • Finisher Control Board |
| Remedy: | 1 1. Check the Set Clamp home sensor in diagnostics. 2. Does the value change from H to L while rotating the actuator? Go to step 2. Use the transmissive Sensor procedure to diagnose and repair the sensor. 2 Does the solenoid energize when running the Set Clamp Paddle test in diagnostics? Go to step 3. Go to step 4. 3 1. Run the Eject Forward Test and then the Eject Release Test in diagnostics. 2. Does the set clamp paddle turn once? Replace the finisher control board. Go to step 4. 4 Is +24 VDC present at P848A-10? Go to step 5. Go to step 6. 5 Is +24 VDC present at P848A-11? Replace the finisher control board. Replace the set clamp solenoid. 6 Is +24 VDC present at test point 9 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. |
| Error code: | 141 |
| Display: | SVC 141 ERROR |
| Description: | Motor |
| Causes: | • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor excessive PWM - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board” |
| Error code: | 143 |
| Display: | Service Call 143:Error |
| Description: | Motor |
| Causes: | • SBU defective • IPU defective • BCU defective • Harness between the SBU and IPU defective • Harness between the BCU-IPU defective • Standard white plate not installed correctly, or is dirty • Scanner mirrors and/or lenses are dirty or installed incorrectly |
| Remedy: | DC pick motor, no encoder feedback - staging motor - replace the “Staging motor” on page 4-79. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 165 |
| Description: | Out of Paper; Load Tray 1 (MPT) with [size] [type] The Tray 1 (MPT) No Paper Sensor indicates Tray 1 (MPT) is empty. |
| Causes: | • No Paper Sensor, PL5.3.14 • No Paper Sensor Actuator, PL5.3.15 • FRONT/DUP Harness, PL5.3.28 |
| Remedy: | 1 Fill Tray 1 (MPT) with paper. Does the error persist? Go to Step 2. Complete. 2 Check the following for evidence of fault or damage: • Tray 1 (MPT) No Paper Sensor, PL5.3.14 • Sensor Actuator, PL5.3.15 Is there any damage? Replace any damaged parts. Go to Step 3. 3 Test the Tray 1 (MPT) No Paper Sensor. Run the Service Diagnostics Tray 1 (MPT) No Paper Sensor test. Does the sensor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the Tray 1 (MPT) No Paper Sensor signal. Is there +3.3 V across P/J135-1 <=> P/J135-2? Replace the sensor. Go to Step 5. 5 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J135. 2. Check continuity between J13 <=> J134. Replace the Engine Control Board. Replace the FRONT/DUP Harness. |
| Error code: | 193 |
| Description: | Image transfer error The IPU board does not finish within 1 minute after the image data has been transferred to the controller board. |
| Causes: | • IPU board defective • Controller board defective • Video controller defective |
| Error code: | 195 |
| Description: | Serial Number Error |
| Causes: | The serial number stored in the memory (EGB) is not correct. |
| Remedy: | EEPROM defective EGB replaced without original EEPROM |
| Error code: | 196 |
| Description: | Replace Imaging Unit or Imaging Unit Is Near End of Life The Imaging Unit Life counter indicates the Imaging Unit is near or has reached its end of life. |
| Causes: | • Imaging Unit, PL6.1.1 • CRUM Connector, PL7.1.4 • PHD2 Harness, PL7.1.7 • FAN/PHD/MOT Harness, PL10.1.9 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Imaging Unit PL6.1.1 • CRUM Connector PL7.1.4 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Replace the Imaging Unit. Does the error persist? Go to Step 3. Complete 3 Check Imaging Unit CRUM connection. Are P/J710 and P/J484 connected? Go to Step 4. Reconnect the CRUM Connector. 4 Check all pins on the PHD2 Harness PL7.1.7 for continuity. 1. Disconnect P/J710 and P/J484. 2. Check continuity between J484<=>J710 Go to Step 5. Replace the PHD2 Harness. 5 Check all pins on the FAN/PHD/MOT Harness for continuity. 1. Disconnect P/J484 and P/J48. 2. Check continuity between J48 <=> P484 Replace the Engine Control Board. Replace the FAN/ PHD/MOT Harness |
| Error code: | 197 |
| Description: | DFGATE error The DFGEATE signal has already been asserted at the original scan. |
| Causes: | • ADF interface cable defective • SBCU board defective • Mismatched firmware between the SBCU board and ADF |
| Error code: | 198 |
| Description: | Memory address error The IPU board does not receive the memory address from the controller board. |
| Causes: | • Mismatched firmware between the SBCU board and controller board • Controller defective • SBCU defective • IPU board defective Note: Before you replace a board, update the firmware. This can repair the error. |
| Error code: | 199 |
| Description: | Service Reflash RIP |
| Causes: | • ADF interface cable defective • SBCU board defective • Mismatched firmware between the SBCU board and ADF |
| Remedy: | The printer has detected an invalid version of the RIP code and must be reflashed to the approved version. Contact your next level support. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 320 |
| Display: | Reset fuser 320: Fuser error |
| Description: | Same unit not detected upon power ON or opening cover. |
| Causes: | 1) Is error message displayed? 2) Is fuser unit set properly? 3) Does error reoccur? |
| Remedy: | Check if fuser is set properly. Reset fuser and turn ON power again. Replace fuser unit assembly. |
| Error code: | 322 |
| Description: | Synchronization error The synchronization signal was not issued within 500 ms after the LD fired while the polygon motor was turning at the prescribed number of revolutions. |
| Causes: | • Laser synchronization board connectors or harness loose, disconnected, or damaged • Laser synchronization board defective or out of position • LD drive board defective |
| Remedy: | 1. Check the harness connection of the development HVPS. 2. Replace the development HVPS. 3. Replace the development unit. |
| Error code: | 323 |
| Display: | Open/close cover 323: Paper thickness error |
| Description: | Sensor output out of range with no media. (Only for Factory Mode) |
| Causes: | 1) Are foreign objects mixed in sensor? 2) Does printer recover when detecting paper thickness by opening/closing tray? 3) Does printer recover by power OFF/ON. |
| Remedy: | Remove foreign objects. Normal. |
| Error code: | 350 |
| Description: | ID sensor error 1 One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. Vsp greater than or equals 2.5V Vsg less than 2.5 Vsp = 0V Vsg = 0 |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 351 |
| Description: | ID sensor error 2 The ID sensor output voltage is 5.0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 352 |
| Description: | ID sensor error 3 For 2 s during the ID sensor pattern check, the ID sensor pattern edge voltage is not 2.5V or the pattern edge is not detected within 800 ms. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 353 |
| Description: | ID sensor error 4 One of the following ID sensor output voltages is detected at ID sensor initialization. Vsg less than 4.0V when the maximum PWM input (255) is applied to the ID sensor. Vsg greater than or equal to 4.0V when the minimum PWM input (0) is applied to the ID sensor. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 354 |
| Display: | Set new fuser 354: Fuser life |
| Description: | Fuser life (occurs when fuser life continuation is OFF). |
| Causes: | Right after replacing fuser? |
| Remedy: | Check fuser life. Replace fuser. |
| Error code: | 355 |
| Display: | Set new belt 355: Belt life |
| Description: | Belt life notified (alarm). Print N-count by opening and closing cover. |
| Causes: | Right after replacing belt? |
| Remedy: | Check belt life. Replace belt. |
| Error code: | 389 |
| Display: | Open top cover 389: Paper jam |
| Description: | Jam generated in paper path. |
| Causes: | Open front cover and check jammed paper. |
| Remedy: | Remove jammed paper. |
| Error code: | 390 |
| Display: | Check MP tray 390: Paper jam |
| Description: | Paper jam during paper feed from MT. |
| Causes: | Check for miss-fed paper around MT cassette. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace MT. |
| Error code: | 391 |
| Description: | TD sensor error: Auto adjust error During automatic adjustment of the TD sensor, output voltage was less than 1.8V, or more than 4.8V during TD sensor initial setting |
| Causes: | • TD sensor connector or harness loose, broken, defective • TD sensor defective • IOB defective • Toner supply defective (confirm that the toner seal strip has been removed from toner cartridge) |
| Remedy: | 1. Check the harness or harness connection. 2. Clean the surface of the quenching lamp glass. |
| Error code: | 392 |
| Description: | Development Bias Error The development bias feedback voltage was less than 0.3 V for longer than 200 ms while the PWM duty value was more than 5% (indicating a development bias leak). |
| Causes: | • Bias terminal damaged • High voltage cable damaged, defective • CGB power pack defective |
| Error code: | 398 |
| Description: | Drum/Development motor error: C The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on. |
| Causes: | • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system |
| Remedy: | 1. Check or replace the harness. 2. Replace the drum/development motor. 3. Replace the 24V fuse on the PSU. |
| Error code: | 399 |
| Description: | Drum/Development motor error: Y The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on. |
| Causes: | • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system |
| Remedy: | 1. Check or replace the harness. 2. Replace the drum/development motor. 3. Replace the 24V fuse on the PSU. |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 411 |
| Display: | SVC 411 ERROR |
| Description: | IRQ timer 1 error |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | Replace the Controller board. |
| Error code: | 490 |
| Display: | Set 490: No paper in MP tray (* stands for A4 B4, etc.) |
| Description: | ITB (Image Transfer Belt) Unit Set Error |
| Causes: | The TM sensor does not detect the reflection from the ITB. |
| Remedy: | • No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S |
| Error code: | 500 |
| Description: | Transport/Fusing Motor Error |
| Causes: | The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the transport/fusing motor. Replace it if necessary. |
| Error code: | 501 |
| Display: | Service Call 501: Error |
| Description: | Tray 1 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503 |
| Display: | Service Call 503: Error |
| Description: | Tray 3 must be rebuilt |
| Causes: | (A model other than D581) Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. (D581) Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 504 |
| Description: | Tray 4 must be rebuilt |
| Causes: | The 2nd tray of D580, 1st tray of D580 when D579 and D580 are attached, the bottom D579 when two units of D579 are attached, or D631 when D581 and D631 are attached. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection D581 when D579 and D581 are attached.Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 506 |
| Display: | SYSTEM HALT (*) 506 : STATION SENS |
| Description: | Bypass must be rebuilt |
| Causes: | • Paper tray unit main motor connector or harness loose, broken, defective • Motor overload due to an obstruction • Motor defective |
| Remedy: | 1. Replace the tray 3 or 4 lift motor. 2. Replace the tray 3 or 4 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3 or 4. |
| Error code: | 508 |
| Description: | Replace black developer |
| Causes: | • HP sensors on the left and right side loose, disconnected, defective • Cutter motor harness damaged, defective • HP sensors defective • Cutter motor defective Note: Paper can be fed from the bypass table if the roll feeder or paper cassette is not operationg. |
| Error code: | 509 |
| Display: | SYSTEM HALT (*) 509 : HDC POSCNT |
| Description: | Replace red developer |
| Causes: | • Poor connection or defective tray 5 or 6 lift motor • Poor connection or defective tray 5 or 6 lift sensor • Remaining paper or another obstruction has stopped the tray and motor. • Pick-up solenoid 5 or 6 connector is loose. • Pick-up solenoid 5 or 6 is blocked by an obstruction. |
| Remedy: | 1. Replace the tray 5 or 6 lift motor. 2. Replace the tray 5 or 6 lift sensor. 3. Check or clear obstacles around pick-up solenoid 5 or 6. |
| Error code: | 510 |
| Display: | SYSTEM HALT (*) 510 : X ORGIN |
| Description: | Replace green developer |
| Causes: | • Tray lift motor defective or connector disconnected • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Remedy: | 1. Check the harness connection or replace it. 2. Replace the bypass tray lift motor. 3. Replace the bypass upper limit sensor. 4. Replace the bypass lower limit sensor. 5. Check or clear obstacles around the bypass pick-up solenoid. |
| Error code: | 520 |
| Description: | Replace optics filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 548 |
| Description: | Low Temperature Error |
| Causes: | The center thermistor detects 100°C or less for 4 seconds. |
| Remedy: | • Defective fusing lamp • Defective thermistor 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.d |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 590 |
| Description: | Toner collection motor error The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on. |
| Causes: | • Motor lock due to obstruction • Motor driver board defective • Motor connection loose, defective • Toner collection motor sensor disconnected, sensor defective • Rotational transmission shaft (o6 x 30) missing |
| Error code: | 611 |
| Display: | ERROR 611 Case Weight |
| Description: | Mechanical counter error: FC This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 612 |
| Display: | ERROR 612 INK LVL LOW |
| Description: | BICU - ADF communication/command abnormal A command that cannot be executed was sent from the main machine to the ADF. |
| Causes: | • A software error, result of an abnormal procedure. |
| Remedy: | Enter the cartridge weight from "CART WEIGHT" menu of "SET UP". |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 650 |
| Description: | @Remote communication error 1 A dial-up or modem error occurred during @Remote operation. (This error occurs only during @Remote operation.) |
| Causes: | • Modem line disconnected • Modem board missing or not properly installed |
| Error code: | 669 |
| Description: | EEPROM Error |
| Causes: | An unexpected value exists in the initialization flag of the EEPROM |
| Remedy: | • EEPROM not initialized • Defective EEPROM |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 720 |
| Description: | Fan folder transport motor error A transport motor lock signal was detected for more than 5 sec. while the motor was running. |
| Causes: | • Transport motor harness connector loose, disconnected, broken • Motor overload due to an obstruction • Transport motor defective • Fan folder unit MCU defective |
| Error code: | 721 |
| Description: | Jogger motor error • Jogger HP sensor does not detect the jogger fence for 2000ms after the jogger unit has moved to its home position. • Jogger HP sensor does not turn off 300 ms after the jogger unit has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective jogger HP sensor • Overload on the jogger motor • Defective jogger motor • Defective main board • Disconnected or defective harness |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the jogger HP sensor (if the jogger motor works correctly). 3. Replace the jogger motor (if the jogger motor does not work). 4. Replace the finisher main board. |
| Error code: | 722 |
| Description: | Finisher jogger motor error The finisher jogger HP sensor did not return to the home position, or move out of the home position, within 1.25 sec. Staple mode cannot be used. |
| Causes: | • Jogger motor connector or harness loose, broken, defective • Jogger motor defective • Jogger HP sensor connector or harness loose, broken, defective • Jogger HP sensor defective |
| Error code: | 724 |
| Description: | Finisher staple hammer motor error Stapling does not finish within 150 ms after the staple hammer motor turned on. Staple mode cannot be used. |
| Causes: | • Staple jam • Stapler overload caused by trying to staple too many sheets • Staple hammer motor connector or harness loose, broken, defective • Staple hammer motor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the staple hammer motor HP sensor if the motor is rotating. 4. Replace the finisher main board. |
| Error code: | 725 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor. 4. Replace the finisher main board. |
| Error code: | 726 |
| Description: | Front shift jogger motor error (B703) The sides fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift jogger motor disconnected, defective • Shift jogger motor overloaded due to obstruction • Shift jogger HP sensor disconnected, defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift jogger HP sensor 4. Replace the shift jogger motor. 5. Replace the finisher main board. |
| Error code: | 727 |
| Description: | Rear shift jogger motor (B703) The side fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code |
| Causes: | Motor harness disconnected, loose, defective Motor defective Motor overload HP defective boar |
| Error code: | 728 |
| Description: | Shift jogger retraction motor error (B703) The side fences do not retract within the prescribed time after the retraction motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray jogger lift HP sensor. 4. Replace the shift jogger retraction motor. 5. Replace the finisher main board. |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 731 |
| Description: | Finisher exit guide motor error After the finisher exit guide motor turned on, the exit guide sensor did not activate within 800 ms. |
| Causes: | • Finisher exit guide motor defective harness or connector loose, broken, defective • Finisher exit guide motor defective • Finisher exit guide sensor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the upper tray exit motor. 4. Replace the finisher main board. |
| Error code: | 732 |
| Description: | Finisher shift roller motor error The shift roller HP sensor does not activate within the prescribed time after the shift roller motor turns on. After 2 counts, the SC is logged as a jam. |
| Causes: | • Shift roller HP sensor defective • Sensor harness disconnected, defective • Shift roller motor defective • Finisher main board defective • Shift roller motor overload |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray exit motor. 4. Replace the finisher main board. |
| Error code: | 770 |
| Description: | Shift motor error The shift motor HP sensor does not detect any change for 1.86 seconds after the shift motor has turned on at power on or during its operation. |
| Causes: | Defective shift motor. Defective shift motor HP sensors. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 791 |
| Description: | Bridge unit error The machine recognizes the finisher, but does not recognize the bridge unit. |
| Causes: | The bridge unit is not installed. Defective bridge unit. Re-install the bridge unit. Turn the main power switch off and on. |
| Remedy: | • Re-install the bridge unit. • Turn the main power switch off and on. |
| Error code: | 792 |
| Description: | Finisher error The machine does not recognize the finisher, but recognizes the bridge unit. |
| Causes: | The finisher`s connection is faulty. The finisher is not attached to a device equipped with the bridge unit. Defective finisher. |
| Remedy: | Reconnect the finisher or bridge unit, and then turn the main power switch off and then back on. |
| Error code: | 793 |
| Description: | Finisher gathering roller motor error |
| Causes: | • Motor overload • Loose connection of the gathering roller motor • Defective gathering roller motor |
| Remedy: | • Check the connections to the gathering roller motor. • Replace the gathering roller motor. |
| Error code: | 800 |
| Description: | Startup without video output end error (K) Video transfer to the engine is started, but the engine did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Error code: | 804 |
| Display: | SYSTEM HALT (*) 804 : (C)DMA ADDR |
| Description: | Startup without video input end (K) A video transmission was requested from the scanner, but the scanner did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 838 |
| Display: | SYSTEM HALT (*) 838 : FW/SV MDL |
| Description: | Self-diagnostic Error 10: Clock Generator A verify error occurred when setting data was read from the clock generator via the I2C bus. |
| Causes: | • Replace the controller board |
| Error code: | 840 |
| Description: | EEPROM access error During the I/O processing, reading error is occurred. The 3rd reading failure issues this SC code. During the I/O processing, writing error is occurred. |
| Causes: | Defective EEPROM |
| Error code: | 841 |
| Description: | EEPROM read error Mirrored data of the EEPROM is different from the original data in EEPROM. |
| Causes: | Data in the EEPROM is overwritten for some reason. |
| Error code: | 850 |
| Description: | Net I/F error Duplicate IP addresses. Illegal IP address. Driver unstable and cannot be used on the network |
| Causes: | • IP address setting incorrect • NIB (PHY) board defective • Controller board defective |
| Remedy: | Turn the main switch off and on. |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 862 |
| Description: | Bad sector number error The number of bad sectors in the HDD (image data area) goes over 101. |
| Causes: | • Defective HDD |
| Remedy: | Format the HDD with SP5832-001. Replace the HDD. |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 951 |
| Description: | NVRAM Secure NVRAM Missing |
| Causes: | • Software defective • BICU defective |
| Remedy: | Replace the system board. |
| Error code: | 953 |
| Description: | NVRAM Chip Failure |
| Causes: | • Firmware bug • Update the scanner firmware • IPU defective |
| Remedy: | Indicates the NVRAM chip on the interconnect board has failed. Replace the interconnect board. |
| Error code: | 954 |
| Description: | NVRAM CRC Failure |
| Causes: | • Firmware bug • IPU defective |
| Remedy: | Indicates the NVRAM experienced a CRC failure. Replace the interconnect board. |
| Error code: | 955 |
| Description: | Code CRC <loc> |
| Causes: | • Firmware bug • Hard disk unit defective • Controller defective • MCU defective • IPU defective |
| Remedy: | Replace the system board. Where <loc> = CRC Failure or ECC Failure on the system board. |
| Error code: | 964 |
| Description: | Emulation Error |
| Causes: | • Software defective |
| Remedy: | Indicates a failure within the Download Emulation which is programmed into the code overlay card. The specific error is as follows: 964 - Download Emulation CRC Failure. Checksum Failure. |
| Error code: | 984 |
| Display: | Service call 984: Error. |
| Description: | <device> |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected |
| Remedy: | Invalid command parameter received by the specified device. Note: Service errors 980 thru 984 <device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 986 |
| Display: | Service call 986: Error |
| Description: | Transparency (OHP) Sensor Error |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU Controller disconnected |
| Remedy: | 1 Are connectors CN4 (light emitting) and CN5 (light receiving) on the CK1 daughter board connected properly? Go to step 2. Plug the connector in securely. 2 Test the sensor. While actuating the sensor, does the voltage fluctuate between 0 V and +5 between pins 2 and 3 of connector CN7 of the printer controller board? Replace the printer controller board. Replace the MPF unit. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 995 |
| Description: | Finisher Main Feed Motor abnormal |
| Causes: | -01 D • Defective BCU • NVRAM Replacement error • Install the previous NVRAM • Input the serial number with SP5-811-004, and turn the main power switch off and on. -02 D • Defective NVRAM • Defective controller Perform SP5-825 to download the appropriate data to the NVRAM, and then turn the main power switch off and then back on. -03 D The serial number cannot be identified due to a mistake during controller replacement or mechanical failure. Replace the controller with the correct type. -04 D - Place all parts in the initial state, and then replace the parts according to the procedures described in the manuals. |
| Remedy: | 1 Is there jammed paper or other obstructions in the paper path? Clear the paper path. Go to step 2. 2 Check to ensure the connector PJ6 on the finisher control board and the feed motor assembly cable are properly connected. Are the cables properly connected? Go to step 3. Properly connect the cables. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pins 7 and 8 and +5 V dc (–10%) between pins 7 and 6 on the feed motor assembly cable connector CN1. Is either voltage missing? Go to step 4. Go to step 5. 4 Disconnect the feed motor assembly cable and PJ6 on the finisher control board. Measure continuity on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 5 Replace the feed motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 6 Measure for +24 V dc between pins 1 and 2 on connector PJ3 on the finisher control board. Measure for +5 V dc between pins 1 and 3 on PJ2 on the finisher control board. Is either voltage missing? Replace the power supply. Replace the finisher control board. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
