Ricoh Aficio 3035
Рейтинг
Модули
LASER UNIT
FUSING UNIT 1
DRIVE SECTION 2
DUPLEX UNIT 2
FRAME SECTION 1
PAPER REGISTRATION
VERTICAL TRANSORT
BY-PASS FEED UNIT 1
DUPLEX UNIT 3
OPERATION PANEL ASSY
OPC UNIT 1
ELECTRICAL SECTION 2
TRANSFER UNIT
OPTICS UNIT 3
OPTICS UNIT 2
ELECTRICAL SECTION 1
FRAME SECTION 2
BY-PASS FEED UNIT 2
EXTERIOR 2
PAPER TRAY UNIT
TONER HOPPER UNIT
FUSING UNIT 2
OPTICS UNIT 1
EXTERIOR 3
EXTERIOR 1
PAPER FEED SECTION
DUPLEX UNIT 1
DRIVE SECTION 3
ELECTRICAL SECTION 3
PAPER SEPARATION UNIT 2
Drive Section 1
OPC UNIT 2
DEVELOPMENT UNIT
PAPER SEPARATION UNIT 1
Детали BY-PASS FEED UNIT 1
| Деталь: | Imaging Unit |
| Парткод: | B2131870 |
| Деталь: | Decal - LD |
| Парткод: | G0291980 |
| Деталь: | Cap:Cover:Optical Housing |
| Парткод: | B0771904 |
| Деталь: | Supporting Plate:Cover:Imaging Unit |
| Парткод: | B0771907 |
| Деталь: | Cover - Optical Housing |
| Парткод: | A284 1904 |
| Деталь: | Shield Glass |
| Парткод: | AC01 5025 |
| Деталь: | Harness:Imaging Unit |
| Парткод: | B213 5455 |
| Деталь: | LD Unit |
| Парткод: | B2131891 |
| Деталь: | PCB:Sync Detector:Sharp |
| Парткод: | B213 5320 |
| Деталь: | Polygon Scanner Motor |
| Парткод: | AX06 0303 |
| Деталь: | Heat Sinker:Polygon Scanner:M:Assy |
| Парткод: | B0021898 |
| Деталь: | Seal - Heatsink |
| Парткод: | A2321920 |
| Деталь: | Cylindrical Lens Holder |
| Парткод: | A232 1927 |
| Деталь: | Cylindrical Lens |
| Парткод: | G0201966 |
| Деталь: | Shield Glass - Polygon Motor |
| Парткод: | AC01 5024 |
| Деталь: | MIRROR HOLDER |
| Парткод: | A232 1926 |
| Деталь: | MIRROR |
| Парткод: | AC03 0115 |
| Деталь: | Middle Mirror Holder |
| Парткод: | A2321925 |
| Деталь: | Front Holder - BTL |
| Парткод: | A232 1923 |
| Деталь: | BTL Lens |
| Парткод: | G0201969 |
| Деталь: | Rear Holder - BTL |
| Парткод: | A232 1924 |
| Деталь: | Front Holder - F Theta Mirror |
| Парткод: | A232 1921 |
| Деталь: | F Theta Mirror |
| Парткод: | G020 1968 |
| Деталь: | Rear Holder - F Theta Mirror |
| Парткод: | A232 1922 |
| Деталь: | Sync. Detector Mirror |
| Парткод: | GC03 0020 |
| Деталь: | Holder - Sync. Detector Mirror |
| Парткод: | A2321928 |
| Деталь: | Fusing Unit:NA:Service:Assy |
| Парткод: | B198 7315 |
| Деталь: | Fusing Unit:EU:Service:Assy |
| Парткод: | B198 7715 |
| Деталь: | Fusing Unit:EU |
| Парткод: | B198 7720 |
| Деталь: | Cap- Fusing Cover |
| Парткод: | B004 4133 |
| Деталь: | Guide Plate-fusing Exit |
| Парткод: | B004 4135 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Fusing Cover:Printing |
| Парткод: | B082 4131 |
| Деталь: | Shield:Fusing Cover |
| Парткод: | B082 4144 |
| Деталь: | Shield:Cover:Upper |
| Парткод: | B082 4148 |
| Деталь: | Cover:Duct:Fusing:Front |
| Парткод: | B082 4147 |
| Деталь: | Shield:Cover:Lower |
| Парткод: | B082 4149 |
| Деталь: | Duct:Fusing:Front |
| Парткод: | B082 4142 |
| Деталь: | Shield:Duct:Front Lower |
| Парткод: | B082 4145 |
| Деталь: | Duct:Fusing:Front Lower |
| Парткод: | B082 4152 |
| Деталь: | Shield:Duct:Fusing:Front Lower:Long |
| Парткод: | B082 4153 |
| Деталь: | Bracket:Drawer:Fusing Welding |
| Парткод: | B077 4092 |
| Деталь: | Terminal Plate - Fusing Unit |
| Парткод: | B004 4095 |
| Деталь: | Harness:Fusing:NA |
| Парткод: | B213 4217 |
| Деталь: | Harness:Fusing:EU |
| Парткод: | B213 4227 |
| Деталь: | Cleaning Roller |
| Парткод: | AE04 2084 |
| Деталь: | Roller Busing |
| Парткод: | AA08 2073 |
| Деталь: | Compression Spring:Fusing Cleaning Roller |
| Парткод: | AA06 3668 |
| Деталь: | Fusing Entrance Guide Plate:Upper |
| Парткод: | B082 4123 |
| Деталь: | Lower Entrance Guide Plate |
| Парткод: | B004 4126 |
| Деталь: | Screw: Drawer |
| Парткод: | AA14 3792 |
| Деталь: | Knob Screw |
| Парткод: | G069 6006 |
| Деталь: | Bracket:Harness:Paper Feed |
| Парткод: | B082 5839 |
| Деталь: | Bracket:I/O Board:Right Lower |
| Парткод: | B082 5837 |
| Деталь: | Bracket:BICU:Right Lower |
| Парткод: | B082 1084 |
| Деталь: | Screw - M3 |
| Парткод: | AA14 3567 |
| Деталь: | Harness:DC:Development:Drawer |
| Парткод: | B213 5453 |
| Деталь: | Brushless Motor:Paper Feed:Development:As |
| Парткод: | AX06 0332 |
| Деталь: | Bracket:I/O Board:Right Upper |
| Парткод: | B082 5836 |
| Деталь: | Bracket:I/O Board:Left Upper |
| Парткод: | B082 5832 |
| Деталь: | PCB:IOB |
| Парткод: | B213 5155 |
| Деталь: | Harness:DC:Lower |
| Парткод: | B213 5468 |
| Деталь: | Harness:Paper Feed:Main |
| Парткод: | B082 5426 |
| Деталь: | Harness:DC:Upper Front |
| Парткод: | B213 5469 |
| Деталь: | Harness:DC:Upper |
| Парткод: | B082 5467 |
| Деталь: | Harness:Paper Feed:Sensor |
| Парткод: | B082 5465 |
| Деталь: | Bracket:I/O Board:Left Lower |
| Парткод: | B082 5833 |
| Деталь: | Rise Motor D - 1.92W |
| Парткод: | AX04 0143 |
| Деталь: | Rear Positioning Guide |
| Парткод: | A232 2996 |
| Деталь: | Bracket:Stay:Lengthwise:Rear |
| Парткод: | B0771053 |
| Деталь: | Shield Plate - DC Motor |
| Парткод: | B004 1322 |
| Деталь: | Shield Plate - BICU |
| Парткод: | B004 1321 |
| Деталь: | Plate - Optical Housing Unit |
| Парткод: | B004 1936 |
| Деталь: | Push Switch - Paper Size |
| Парткод: | G020 2620 |
| Деталь: | Harness:Paper Size Sensor |
| Парткод: | B082 5455 |
| Деталь: | Holder - Optical Housing Unit |
| Парткод: | B0041939 |
| Деталь: | Hook - Unit Release |
| Парткод: | A232 4685 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 6152 |
| Деталь: | Cushion:Duplex Unit |
| Парткод: | AA16 2080 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | BRACKET:ENTRANCE SENSOR |
| Парткод: | B077 4763 |
| Деталь: | Reverse Roller:Driven |
| Парткод: | AF02 0652 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0307 |
| Деталь: | Pressure Spring - Driven |
| Парткод: | AA06 0839 |
| Деталь: | Guide Plate:Reverse:Peen |
| Парткод: | B077 4634 |
| Деталь: | Reverse Roller |
| Парткод: | AF02 0659 |
| Деталь: | Grip:Un Lock |
| Парткод: | B077 4684 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2074 |
| Деталь: | Harness:Duplex Unit:Sensor |
| Парткод: | B082 5461 |
| Деталь: | Harness:Duplex Unit |
| Парткод: | B082 5460 |
| Деталь: | Link:Dc Solenoid:Assy |
| Парткод: | B213 4690 |
| Деталь: | Reverse Roller Gear |
| Парткод: | AB01 4161 |
| Деталь: | Bracket:Stepper Motor:Reverse |
| Парткод: | B213 4666 |
| Деталь: | Stepper Motor:Duplex:Sub-assy |
| Парткод: | B213 4664 |
| Деталь: | Timing Belt - S2M 140 |
| Парткод: | AA04 3443 |
| Деталь: | Gear - 24Z |
| Парткод: | AB03 0670 |
| Деталь: | Gear - 46Z |
| Парткод: | AB01 4162 |
| Деталь: | Bracket: Base |
| Парткод: | B077 4800 |
| Деталь: | PCB:Duplex Unit |
| Парткод: | B213 5140 |
| Деталь: | Stay:Paper Exit Sub-unit:Left |
| Парткод: | B0771066 |
| Деталь: | Bracket:Plate:Joint Unit |
| Парткод: | B0771067 |
| Деталь: | Decal:Warning (High Temperature) |
| Парткод: | B213 4122 |
| Деталь: | Supporter:Development Unit |
| Парткод: | B0771078 |
| Деталь: | Positioning Pin - Laser Unit Assy |
| Парткод: | A2321937 |
| Деталь: | Bracket:Connector:Fusing |
| Парткод: | B0771054 |
| Деталь: | Guide:Toner Supply Unit:Assy |
| Парткод: | B077 3210 |
| Деталь: | Stopper - Slide Rail |
| Парткод: | A232 3264 |
| Деталь: | Bracket:Shaft:Stopper:Assy |
| Парткод: | B0771051 |
| Деталь: | Stay:Around The Photoconductor |
| Парткод: | B082 2362 |
| Деталь: | Magnet - Discharge Lamp |
| Парткод: | B082 2363 |
| Деталь: | LED Array:Ql |
| Парткод: | AX50 0092 |
| Деталь: | Supporter:Fusing Unit:Welding |
| Парткод: | B0771071 |
| Деталь: | Stopper - Fusing Unit |
| Парткод: | A232 4201 |
| Деталь: | Knob:Registration |
| Парткод: | AG05 0099 |
| Деталь: | Gear:Pulley - 20Z/30T |
| Парткод: | AB03 0778 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2080 |
| Деталь: | Gear -16Z |
| Парткод: | AB01 4051 |
| Деталь: | Front Bushing - M6 |
| Парткод: | AA08 0229 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 2304 |
| Деталь: | Stopper - Guide Plate |
| Парткод: | A232 2578 |
| Деталь: | TORSION SPRING |
| Парткод: | AA06 6577 |
| Деталь: | Link:Cover:Assy |
| Парткод: | B077 3985 |
| Деталь: | Pin - Link |
| Парткод: | AA14 9291 |
| Деталь: | Link:Guide Plate:Open And Close |
| Парткод: | B077 2596 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Grip:Guide Plate |
| Парткод: | B082 2575 |
| Деталь: | Decal - A2 |
| Парткод: | AA00 1393 |
| Деталь: | Bracket:Registration Roller |
| Парткод: | B082 2614 |
| Деталь: | Case:Registration Roller:Assy |
| Парткод: | B082 2611 |
| Деталь: | Guide Plate:Entrance:Lower:Adhesion |
| Парткод: | B077 2583 |
| Деталь: | Bracket:Registration Sensor |
| Парткод: | B077 2594 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0106 |
| Деталь: | Harness:Registration Sensor |
| Парткод: | B082 5420 |
| Деталь: | Guide Plate:Entrance:Upper:Peen |
| Парткод: | B082 2574 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 2305 |
| Деталь: | Registration Roller:Driven:MM16 |
| Парткод: | AF02 1083 |
| Деталь: | Registration Roller:Drive:MM20 |
| Парткод: | AF02 0608 |
| Деталь: | Guide - Transfer Entrance |
| Парткод: | A232 1074 |
| Деталь: | Stay:Drum:Lower:Assy |
| Парткод: | B082 1072 |
| Деталь: | Shield - Stay - PCU |
| Парткод: | AA15 3442 |
| Деталь: | Cleaner:Registration Roller:Assy |
| Парткод: | B082 2603 |
| Деталь: | Case:Cleaner:Registration Roller |
| Парткод: | B082 2602 |
| Деталь: | Spur |
| Парткод: | B004 2310 |
| Деталь: | Supporter:PCU |
| Парткод: | B082 2403 |
| Деталь: | Holder - ID Sensor |
| Парткод: | A232 2366 |
| Деталь: | Density Sensor:P |
| Парткод: | B213 2367 |
| Деталь: | SPRING HOLDER |
| Парткод: | A232 1284 |
| Деталь: | Receptacle:Transfer Belt |
| Парткод: | B213 1127 |
| Деталь: | Terminal Spring |
| Парткод: | AA06 3304 |
| Деталь: | Magnetic Clutch:0.5n.m:28z |
| Парткод: | AX20 0280 |
| Деталь: | Rear Bushing - M6 |
| Парткод: | AA08 0230 |
| Деталь: | Timing Belt:50S2M192 |
| Парткод: | AA04 3580 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2072 |
| Деталь: | Shaft:Drive:Registration |
| Парткод: | B213 2575 |
| Деталь: | Bracket:Registration:Drive:Front |
| Парткод: | B213 2570 |
| Деталь: | Gear - 16Z |
| Парткод: | AB01 4276 |
| Деталь: | Gear - 17Z |
| Парткод: | AB01 4275 |
| Деталь: | Timing Pulley - 30T |
| Парткод: | AB03 0779 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Frame Seal - Rear Vertical |
| Парткод: | AA15 3393 |
| Деталь: | Harness:Connecting:Right Rear |
| Парткод: | B213 5470 |
| Деталь: | Frame Seal - Rear Right |
| Парткод: | AA15 3391 |
| Деталь: | HOOK LEVER |
| Парткод: | A232 3950 |
| Деталь: | Spring Plate - Band Stopper |
| Парткод: | A232 3962 |
| Деталь: | Band Stopper |
| Парткод: | A232 3963 |
| Деталь: | Decal:Drum:Belt |
| Парткод: | B082 3992 |
| Деталь: | Inner Cover:Right |
| Парткод: | B0771305 |
| Деталь: | Inner Cover:Right:EU |
| Парткод: | B077 6322 |
| Деталь: | Lever:Handle:C3 |
| Парткод: | B077 3999 |
| Деталь: | Screw - MM4.5 |
| Парткод: | B213 4330 |
| Деталь: | Guide Roller |
| Парткод: | AF04 0571 |
| Деталь: | Guide Plate:Exit:Entrance |
| Парткод: | B082 4322 |
| Деталь: | Grounding Plate - Exit Sensor |
| Парткод: | B004 4329 |
| Деталь: | Harness:Used Toner Sensor |
| Парткод: | B213 5466 |
| Деталь: | Bracket:Paper Feed Sensor |
| Парткод: | B077 4323 |
| Деталь: | Upper Entrance Guide |
| Парткод: | A232 3998 |
| Деталь: | Lower Entrance Guide |
| Парткод: | A232 3999 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0118 |
| Деталь: | Rear Hook - Right Cover |
| Парткод: | A232 3948 |
| Деталь: | TORSION SPRING |
| Парткод: | AA06 6576 |
| Деталь: | Shaft:Hook |
| Парткод: | B213 3821 |
| Деталь: | TORSION SPRING |
| Парткод: | AA06 6575 |
| Деталь: | Front Hook - Right Cover |
| Парткод: | A232 3945 |
| Деталь: | Sponge - 24x6x5 |
| Парткод: | AA15 3392 |
| Деталь: | Cover:Right |
| Парткод: | B082 3943 |
| Деталь: | Bushing - 6x8x5.8 |
| Парткод: | AA08 2079 |
| Деталь: | Stopper - Right Cover |
| Парткод: | A232 3942 |
| Деталь: | Cover:Fan |
| Парткод: | B213 3956 |
| Деталь: | Fan Motor Sirocco:DC24V:3350rpm |
| Парткод: | AX64 0162 |
| Деталь: | Shaft:Contact Point:Cover:Right |
| Парткод: | B213 3945 |
| Деталь: | Duct:Cooling:Fusing:Right |
| Парткод: | B082 3951 |
| Деталь: | Shielding Plate:Cover:Right |
| Парткод: | B082 4199 |
| Деталь: | Spring - 3.5n |
| Парткод: | AA06 3855 |
| Деталь: | Bushing - 4mm |
| Парткод: | B004 4327 |
| Деталь: | Roller:Driven |
| Парткод: | B213 4328 |
| Деталь: | Sheet:Inner Cover:Right |
| Парткод: | B213 1306 |
| Деталь: | Cover:Holder:Middle |
| Парткод: | B077 6106 |
| Деталь: | Cover:Manual Feed:Front |
| Парткод: | B077 6109 |
| Деталь: | Frame:Holder:Assy |
| Парткод: | B082 6095 |
| Деталь: | Roller - Holder |
| Парткод: | A232 6092 |
| Деталь: | Driven Roller - M9 |
| Парткод: | AF04 0559 |
| Деталь: | Cover:Manual Feed:Inner Back |
| Парткод: | B077 6108 |
| Деталь: | Supporting Plate:Contact Point |
| Парткод: | B004 6024 |
| Деталь: | Cover:Contact Point |
| Парткод: | B077 6107 |
| Деталь: | Bushing - 8x16x7 |
| Парткод: | AA08 2070 |
| Деталь: | Pad - Side Fence |
| Парткод: | G060 2908 |
| Деталь: | TORSION SPRING |
| Парткод: | AA06 6574 |
| Деталь: | Positioning Pin |
| Парткод: | A232 6091 |
| Деталь: | Manual Feed Table:SUB-Assy |
| Парткод: | B198 6009 |
| Деталь: | Side Fence:Auxiliary:Front |
| Парткод: | B077 6071 |
| Деталь: | Side Fence:Front |
| Парткод: | B077 6069 |
| Деталь: | Side Fence:Auxiliary:Rear |
| Парткод: | B077 6072 |
| Деталь: | Side Fence:Inner Back |
| Парткод: | B077 6070 |
| Деталь: | MANUAL FEED TABLE |
| Парткод: | B077 6067 |
| Деталь: | Paper Guide - Manual Feed Tabl |
| Парткод: | G060 2905 |
| Деталь: | Decal:Manual Feed Direction |
| Парткод: | B082 6073 |
| Деталь: | Paper size sensor |
| Парткод: | B198 6080 |
| Деталь: | Rear Rack |
| Парткод: | A232 6083 |
| Деталь: | Gear - 16Z |
| Парткод: | G011 3305 |
| Деталь: | Front Rack |
| Парткод: | A232 6082 |
| Деталь: | Cover:Manual Feed Table |
| Парткод: | B077 6068 |
| Деталь: | Support Stay:Sub-Assy |
| Парткод: | B082 6010 |
| Деталь: | Timing Belt - S2M 350 |
| Парткод: | AA04 3444 |
| Деталь: | Pulley - 24T |
| Парткод: | AB03 0474 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2075 |
| Деталь: | Bracket:Sensor |
| Парткод: | B077 4795 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0106 |
| Деталь: | Harness:Duplex Unit:Sensor |
| Парткод: | B082 5462 |
| Деталь: | Stay:Middle |
| Парткод: | B077 4796 |
| Деталь: | Exit Transport Roller |
| Парткод: | AF02 0510 |
| Деталь: | Guide Plate - Right Lower |
| Парткод: | B004 4622 |
| Деталь: | Transport Roller:Middle |
| Парткод: | AF02 0654 |
| Деталь: | Bracket:Micro Switch:Assy |
| Парткод: | B077 4697 |
| Деталь: | Link:Duplex |
| Парткод: | B213 4790 |
| Деталь: | TORSION SPRING |
| Парткод: | AA06 6335 |
| Деталь: | Stepper Motor:Duplex:Sub-assy |
| Парткод: | B213 4664 |
| Деталь: | Gear - 30Z |
| Парткод: | AB01 1088 |
| Деталь: | Bracket:Stepper Motor:Paper Feed |
| Парткод: | B213 4678 |
| Деталь: | Bracket:Sensor:Paper Feed |
| Парткод: | B077 4757 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0158 |
| Деталь: | Timing Belt - S2M 140 |
| Парткод: | AA04 3443 |
| Деталь: | Gear Pulley - TRANSPORT |
| Парткод: | AB03 0671 |
| Деталь: | Stay:Lower |
| Парткод: | B077 4630 |
| Деталь: | Screw - MM3:M2.5 |
| Парткод: | AA14 3561 |
| Деталь: | Operation Panel:NA |
| Парткод: | B198 6350 |
| Деталь: | Operation Panel:EU |
| Парткод: | B198 6360 |
| Деталь: | Operation Panel:ASIA |
| Парткод: | B198 6385 |
| Деталь: | Earth Sheet - Touch Panel |
| Парткод: | B004 1517 |
| Деталь: | Touch Panel:HVGA |
| Парткод: | B213 5222 |
| Деталь: | Cushion:Touch Panel:Short |
| Парткод: | B0041525 |
| Деталь: | Cushion:Touch Panel:Long |
| Парткод: | B004 1526 |
| Деталь: | LCD:HVGA:SH:BL |
| Парткод: | B180 5259 |
| Деталь: | Bracket:LCDC |
| Парткод: | B0771520 |
| Деталь: | PCB:LCDC:NA |
| Парткод: | B198 5203 |
| Деталь: | PCB:LCDC:EU |
| Парткод: | B198 5204 |
| Деталь: | PCB:LCDC:TWN |
| Парткод: | B198 5205 |
| Деталь: | Cover:LCDC |
| Парткод: | B077 1521 |
| Деталь: | Dial:Contrast |
| Парткод: | B077 1513 |
| Деталь: | Keytop:Counter |
| Парткод: | B077 1511 |
| Деталь: | Cover:Basic |
| Парткод: | B0771535 |
| Деталь: | PCB:Operation Panel:Left |
| Парткод: | B213 1519 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B0041503 |
| Деталь: | Keytop:Power Source |
| Парткод: | B0771506 |
| Деталь: | Keytop:Try Print |
| Парткод: | B0771504 |
| Деталь: | Keytop - Start |
| Парткод: | B0041505 |
| Деталь: | Keytop:Confirm |
| Парткод: | B077 1510 |
| Деталь: | Keytop:Block Diagram |
| Парткод: | B0771509 |
| Деталь: | Keytop:Clear Modes |
| Парткод: | B077 6358 |
| Деталь: | Keytop:Preheat |
| Парткод: | B0771508 |
| Деталь: | Keytop: Interrupt |
| Парткод: | B077 1512 |
| Деталь: | Keytop:10key |
| Парткод: | B0771502 |
| Деталь: | Keytop: 10key:NA |
| Парткод: | B077 6355 |
| Деталь: | Keytop: 10key:AA |
| Парткод: | B077 6387 |
| Деталь: | Cover:Application |
| Парткод: | B0771534 |
| Деталь: | PCB:Operation Panel:Right |
| Парткод: | B213 1518 |
| Деталь: | Keytop:Copy:1 :NA |
| Парткод: | B077 6356 |
| Деталь: | Keytop:Copy:1 :EU |
| Парткод: | B077 6366 |
| Деталь: | Keytop:Copy:2:NA |
| Парткод: | B077 6357 |
| Деталь: | Keytop:Copy:2:EU |
| Парткод: | B077 6367 |
| Деталь: | Sheet:Caption:NA |
| Парткод: | B077 6354 |
| Деталь: | Entrance Seal - Toner Supply |
| Парткод: | G065 2279 |
| Деталь: | Handle - PCU |
| Парткод: | G065 2259 |
| Деталь: | Cover:PCU:Upper:Assy |
| Парткод: | G065 2251 |
| Деталь: | Cap - Toner Supply |
| Парткод: | G065 2328 |
| Деталь: | Stopper:PCU:C3 |
| Парткод: | B082 2217 |
| Деталь: | Compression Spring:Stopper:PCU |
| Парткод: | G065 2219 |
| Деталь: | Tension Spring - Shutter |
| Парткод: | AA06 2316 |
| Деталь: | Shutter - Toner Supply |
| Парткод: | G065 2241 |
| Деталь: | Electrode Plate:Charge:Receptacle:Abk:Assy |
| Парткод: | G065 2271 |
| Деталь: | Frame:PCU:Upper:Assy |
| Парткод: | B082 2220 |
| Деталь: | SPRING HOLDER |
| Парткод: | A232 1284 |
| Деталь: | Tape - Entrance Seal |
| Парткод: | A232 2280 |
| Деталь: | Cleaning Entrance Seal |
| Парткод: | AD04 7023 |
| Деталь: | Front Entrance Seal - Toner Supply |
| Парткод: | A232 3267 |
| Деталь: | Shield - Collection Coil |
| Парткод: | AA15 0671 |
| Деталь: | Entrance Seal - Toner Supply |
| Парткод: | B004 2215 |
| Деталь: | Toner Collection Coil |
| Парткод: | B213 2292 |
| Деталь: | Bushing - Toner Collection Coil |
| Парткод: | A232 2292 |
| Деталь: | Gear - 14Z |
| Парткод: | AB01 1377 |
| Деталь: | Front Bushing - Collection Mylar |
| Парткод: | A232 2289 |
| Деталь: | Shaft - Toner Collection Mylar |
| Парткод: | A232 2288 |
| Деталь: | Collection Coil:Assy |
| Парткод: | B082 2288 |
| Деталь: | Bushing - Collection Mylar |
| Парткод: | A232 2290 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1378 |
| Деталь: | Bracket:Idler |
| Парткод: | B213 2290 |
| Деталь: | Cam - Cleaning Blade |
| Парткод: | AB01 1380 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1379 |
| Деталь: | Tape:Cover:PCU |
| Парткод: | B082 2307 |
| Деталь: | Cover:PCU |
| Парткод: | B082 2306 |
| Деталь: | Frame:PCU:Lower:Assy |
| Парткод: | B082 2302 |
| Деталь: | Decal:PCU:Spring:Caution Chart |
| Парткод: | AA00 3206 |
| Деталь: | Stud:Contact Point:Cleaning |
| Парткод: | B213 2316 |
| Деталь: | Shield:PCU:Rail |
| Парткод: | G065 2282 |
| Деталь: | Electrode Plate:Charge:Front |
| Парткод: | G065 2354 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Front Arm - Charge Unit |
| Парткод: | G065 2321 |
| Деталь: | Bushing - 6x10x3 |
| Парткод: | A232 2421 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3648 |
| Деталь: | Front Bushing - Cleaning Bracket |
| Парткод: | A232 2315 |
| Деталь: | Bracket:Cleaning Blade |
| Парткод: | B213 2312 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 2299 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 2300 |
| Деталь: | Collar - Cleaning |
| Парткод: | A232 2318 |
| Деталь: | Rear Arm - Charge Unity |
| Парткод: | G065 2326 |
| Деталь: | Electrode Plate:Charge:Rear |
| Парткод: | G065 2308 |
| Деталь: | Terminale:Brush Roller |
| Парткод: | B082 2333 |
| Деталь: | Cleaning Blade:Assy |
| Парткод: | B213 2354 |
| Деталь: | PCU Unit |
| Парткод: | B198 2203 |
| Деталь: | Seal - Entrance |
| Парткод: | A232 2350 |
| Деталь: | Seal - Blade 12x7x3 |
| Парткод: | A232 2348 |
| Деталь: | Seal - 2x20x45 |
| Парткод: | A232 2414 |
| Деталь: | Seal - Blade 13x9.5x3 |
| Парткод: | A232 2399 |
| Деталь: | Bracket: Harness |
| Парткод: | B0771126 |
| Деталь: | Bracket:Harness:Joint Unit |
| Парткод: | B082 5864 |
| Деталь: | Brushless Motor:Fusing/Paper Exit Unit:Assy |
| Парткод: | AX06 0331 |
| Деталь: | Bracket: Fan: Front |
| Парткод: | B0821087 |
| Деталь: | Fan Motor Dc24V/21.6W |
| Парткод: | AX64 0161 |
| Деталь: | Harness:Fusing Unit (EU) |
| Парткод: | B213 5608 |
| Деталь: | Harness:Fusing Unit (NA) |
| Парткод: | B213 5609 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3301 |
| Деталь: | LEVER:SAFETY SWITCH |
| Парткод: | B077 5861 |
| Деталь: | Cover:Lever |
| Парткод: | B077 5862 |
| Деталь: | Bracket:Safety Switch |
| Парткод: | B077 5860 |
| Деталь: | Stepped Screw - M2.5 |
| Парткод: | AA14 3512 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0713 |
| Деталь: | Lever:Safety Switch:Front |
| Парткод: | B077 5865 |
| Деталь: | Bracket:Safety Switch |
| Парткод: | B077 5866 |
| Деталь: | Shadeing Plate:BICU |
| Парткод: | B213 5846 |
| Деталь: | Harness:BICU:IOB |
| Парткод: | B213 5425 |
| Деталь: | Harness:Laser Diode Control |
| Парткод: | B213 5445 |
| Деталь: | PCB:BICU |
| Парткод: | B213 5065 |
| Деталь: | Bracket:Bicu:Right Upper |
| Парткод: | B0821083 |
| Деталь: | Bracket: Rack:Application:Assy |
| Парткод: | B082 5880 |
| Деталь: | Bracket:Connector:Harness |
| Парткод: | B077 5825 |
| Деталь: | Mylar - Belt Drive Roller |
| Парткод: | B004 3914 |
| Деталь: | Seal - Transfer Exit |
| Парткод: | A232 3907 |
| Деталь: | Seal - Rear Transfer Exit |
| Парткод: | A232 3906 |
| Деталь: | Seal - Shield Plate |
| Парткод: | A232 3905 |
| Деталь: | Shield - Transfer Belt - Exit |
| Парткод: | A232 3927 |
| Деталь: | Cleaning Blade:Transfer Belt |
| Парткод: | B213 3831 |
| Деталь: | Cleaning Blade Bracket |
| Парткод: | B082 3920 |
| Деталь: | Seal - Front Case |
| Парткод: | A232 3909 |
| Деталь: | Seal - Rear Case |
| Парткод: | A232 3908 |
| Деталь: | Used Toner Sensor:Transfer Unit |
| Парткод: | AW31 0007 |
| Деталь: | Shield:Remove Paper Dust |
| Парткод: | B082 3867 |
| Деталь: | Lever: Re lease: Pressu re |
| Парткод: | B213 3917 |
| Деталь: | Rear Bushing - Cleaning Holder |
| Парткод: | A232 3924 |
| Деталь: | Gear - 27Z |
| Парткод: | AB01 4189 |
| Деталь: | Spring:Pressure:Cleaning Blade:4.4n |
| Парткод: | AA06 0939 |
| Деталь: | Seal - 70x20 |
| Парткод: | AA15 0401 |
| Деталь: | TORSION SPRING |
| Парткод: | AA06 3305 |
| Деталь: | Spring Anchor |
| Парткод: | A232 3921 |
| Деталь: | Shaft - Transfer Unit Stopper |
| Парткод: | A232 3935 |
| Деталь: | Front Bushing - Cleaning Holder |
| Парткод: | A232 3925 |
| Деталь: | Case - Transfer Unit |
| Парткод: | B004 3900 |
| Деталь: | Pressure Lever - Transfer Belt |
| Парткод: | A232 3916 |
| Деталь: | Lever:Front |
| Парткод: | B077 3914 |
| Деталь: | Lever:Rear |
| Парткод: | B077 3913 |
| Деталь: | Spring Plate - Transfer Unit |
| Парткод: | A232 3883 |
| Деталь: | Driven Roller - Transfer Unit |
| Парткод: | A232 3885 |
| Деталь: | Rear Terminal - Transfer Belt |
| Парткод: | A232 3887 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 2054 |
| Деталь: | TORSION SPRING |
| Парткод: | AA06 0712 |
| Деталь: | Roller:Bias |
| Парткод: | B213 3889 |
| Деталь: | Bushing - Bias Roller |
| Парткод: | AA08 0246 |
| Деталь: | Transfer Belt Roller |
| Парткод: | A232 3926 |
| Деталь: | Frame:Transfer Belt |
| Парткод: | B213 3882 |
| Деталь: | Bias Terminal |
| Парткод: | A232 3891 |
| Деталь: | Arm - Transfer Belt |
| Парткод: | A232 3893 |
| Деталь: | Roller:Drive:Dia14.5 |
| Парткод: | B213 3894 |
| Деталь: | Gear - 25Z |
| Парткод: | AB01 1190 |
| Деталь: | Transfer belt |
| Парткод: | A232 3880 |
| Деталь: | Bracket - Heater |
| Парткод: | B004 1728 |
| Деталь: | Heater - 120 V 15W |
| Парткод: | AX40 0140 |
| Деталь: | Heater - 240V 15W |
| Парткод: | AX40 0142 |
| Деталь: | Bracket:Power Supply Cord:Heater:EXP:Ass |
| Парткод: | B004 1741 |
| Деталь: | Bracket:Power Supply Cord |
| Парткод: | B004 1742 |
| Деталь: | Rail Supporter |
| Парткод: | A2321728 |
| Деталь: | Scanner Rail |
| Парткод: | A232 1731 |
| Деталь: | Second Slide Rail |
| Парткод: | A2321707 |
| Деталь: | Shield -base |
| Парткод: | AA15 0711 |
| Деталь: | Rail - Flexible Board |
| Парткод: | B004 1726 |
| Деталь: | Pulley 2 - 22MM |
| Парткод: | B004 1713 |
| Деталь: | Carriage Drive Wire |
| Парткод: | AA05 0106 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0703 |
| Деталь: | Bracket:Tension:Wire:Rear |
| Парткод: | B0771722 |
| Деталь: | Drive Shaft |
| Парткод: | A232 1771 |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | A232 3566 |
| Деталь: | Rear Scanner Pulley |
| Парткод: | AB03 2062 |
| Деталь: | Timing Pulley - Z61 |
| Парткод: | AB03 0572 |
| Деталь: | Timing Belt - S2M-224 |
| Парткод: | AA04 3439 |
| Деталь: | Idler Bracket |
| Парткод: | B004 1714 |
| Деталь: | Lens Block Supporter |
| Парткод: | A232 1713 |
| Деталь: | Rubber Foot:H5 |
| Парткод: | B101 1097 |
| Деталь: | Front Scanner Pulley |
| Парткод: | AB03 2061 |
| Деталь: | Bracket:Tension:Wire:Front |
| Парткод: | B077 1712 |
| Деталь: | Carriage:No.2:Assy |
| Парткод: | B077 1801 |
| Деталь: | Harness Guide |
| Парткод: | A2321808 |
| Деталь: | Spring Plate - 2nd Mirror |
| Парткод: | G404 2810 |
| Деталь: | 2nd Mirror Assy |
| Парткод: | B0041820 |
| Деталь: | Carriage Pulley - 22mm |
| Парткод: | B004 1809 |
| Деталь: | Xenon Lamp:Mm8.5 |
| Парткод: | AX50 0083 |
| Деталь: | Flexible Board:Assy (RIC/INF) |
| Парткод: | B2131846 |
| Деталь: | Flexible Board |
| Парткод: | B2131842 |
| Деталь: | Clamp:Wire:Rear |
| Парткод: | B0771792 |
| Деталь: | Clamp:Wire:Front |
| Парткод: | B0771791 |
| Деталь: | Carriage:No.1 :Assy |
| Парткод: | B0771781 |
| Деталь: | 1st Mirror Holder |
| Парткод: | A2321789 |
| Деталь: | Scanner mirror |
| Парткод: | AC03 0110 |
| Деталь: | Shield:Side Plate:Left |
| Парткод: | AA15 0721 |
| Деталь: | Exposure Glass Holder |
| Парткод: | A284 1674 |
| Деталь: | Shield:Side Plate:Front Rear:Left Middle |
| Парткод: | AA15 0722 |
| Деталь: | Sheet:Left |
| Парткод: | AA15 0723 |
| Деталь: | Sheet:Left Middle |
| Парткод: | AA15 0724 |
| Деталь: | Sheet:Right |
| Парткод: | AA15 0725 |
| Деталь: | Cushion - 4x15x1 |
| Парткод: | AA16 1133 |
| Деталь: | Side Plate:Front |
| Парткод: | B082 1736 |
| Деталь: | Side Plate:Rear |
| Парткод: | B0821738 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Bracket:Home Position Sensor |
| Парткод: | B2131844 |
| Деталь: | Base:Scanner:Rear |
| Парткод: | B0771728 |
| Деталь: | Fan Motor DC24V/2.40W |
| Парткод: | AX64 0167 |
| Деталь: | Duct - Cooling Fan |
| Парткод: | A232 1172 |
| Деталь: | Upper Dust |
| Парткод: | G065 1171 |
| Деталь: | Lower Dust |
| Парткод: | G065 1170 |
| Деталь: | Power Pack:CBT |
| Парткод: | AZ320145 |
| Деталь: | Bracket:Power Pack:Right |
| Парткод: | B077 5812 |
| Деталь: | Bracket:Power Pack:Left |
| Парткод: | B077 5811 |
| Деталь: | Bracket:Power Supply Cord |
| Парткод: | B077 5898 |
| Деталь: | Bracket:Circuit Breaker |
| Парткод: | B077 7757 |
| Деталь: | Bracket:Connector |
| Парткод: | B082 5897 |
| Деталь: | Guide Plate:Arm:Scanner Unit |
| Парткод: | B0771055 |
| Деталь: | Power Supply Cord:NA |
| Парткод: | B213 5601 |
| Деталь: | Power Supply Cord:EU |
| Парткод: | B213 5602 |
| Деталь: | Power Supply Unit:285W |
| Парткод: | AZ23 0186 |
| Деталь: | Power Supply Unit:285W:EU/AA:AD-C4 (1W-PSU) |
| Парткод: | AZ23 0187 |
| Деталь: | Harness:DC:Safety Switch |
| Парткод: | B082 5457 |
| Деталь: | Harness :AC:SW |
| Парткод: | B213 5606 |
| Деталь: | Harness:DC:DC Power Supply |
| Парткод: | B213 5521 |
| Деталь: | Harness:AC:Dehumidifier |
| Парткод: | B213 5611 |
| Деталь: | Harness:Circuit Breaker:EU |
| Парткод: | B213 5603 |
| Деталь: | Spring Plate - Power Supply Unit |
| Парткод: | G034 5820 |
| Деталь: | Heat Sink:Heater |
| Парткод: | B077 2512 |
| Деталь: | Shadeing Plate |
| Парткод: | B2131968 |
| Деталь: | Sheet - Separation Plate |
| Парткод: | B004 2597 |
| Деталь: | Stay:Machine Or Copier:Rear |
| Парткод: | B082 1076 |
| Деталь: | Grip:Rear |
| Парткод: | B2131077 |
| Деталь: | Stay:Machine or Copier:Lengthwise:R |
| Парткод: | B1981093 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Bracket:Hinge:Right |
| Парткод: | B2131267 |
| Деталь: | Rubber Foot:H5 |
| Парткод: | B101 1097 |
| Деталь: | Cap - Positioning |
| Парткод: | B004 2995 |
| Деталь: | Supporter:Paper Tray |
| Парткод: | B213 2990 |
| Деталь: | Front Positioning Guide |
| Парткод: | A232 2995 |
| Деталь: | Grip:Adhesion |
| Парткод: | B077 1021 |
| Деталь: | Stopper:Grip |
| Парткод: | B0771023 |
| Деталь: | Heater Stopper |
| Парткод: | A230 2525 |
| Деталь: | Base:Fix:Development |
| Парткод: | B0771082 |
| Деталь: | Cover:Fix:Development |
| Парткод: | B2131081 |
| Деталь: | Bracket:Hinge:Left |
| Парткод: | B0771266 |
| Деталь: | Sheet:Cover:Fix:Development |
| Парткод: | B2131082 |
| Деталь: | Heater: 120V:9W |
| Парткод: | AX40 0190 |
| Деталь: | Heater:230V:9W |
| Парткод: | AX40 0191 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Feed Roller - Manual Feed |
| Парткод: | AF031046 |
| Деталь: | Guide Plate:Feed |
| Парткод: | B077 6044 |
| Деталь: | Grounding Plate - Feed |
| Парткод: | A232 6046 |
| Деталь: | Gear - 23Z |
| Парткод: | AB01 1387 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | AF03 0049 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3568 |
| Деталь: | Arm Paper Pick Up |
| Парткод: | A232 6043 |
| Деталь: | Feed Shaft |
| Парткод: | AA14 0753 |
| Деталь: | Paper End Feeler |
| Парткод: | A232 6055 |
| Деталь: | Feeler Roller |
| Парткод: | A134 2661 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF04 0031 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Grounding Plate - Reverse |
| Парткод: | A232 6023 |
| Деталь: | Stepped Screw - Guide Plate |
| Парткод: | 52 164 198 |
| Деталь: | Housing:Manual Feed |
| Парткод: | B077 6022 |
| Деталь: | Cover:Gear:Adhesion |
| Парткод: | B082 6038 |
| Деталь: | Rail:Holder |
| Парткод: | B077 6065 |
| Деталь: | Separation Roller - Manual Feed |
| Парткод: | AF03 2046 |
| Деталь: | TORQUE LIMITER |
| Парткод: | B004 2783 |
| Деталь: | Shaft:Separator: Driven |
| Парткод: | B213 6033 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3499 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3016 |
| Деталь: | Guide Plate:Separator:Assy |
| Парткод: | B082 6028 |
| Деталь: | Gear - Z16 |
| Парткод: | AB01 1388 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1389 |
| Деталь: | Shaft - Drive Roller |
| Парткод: | A232 6035 |
| Деталь: | BUSHING - 6MM |
| Парткод: | GA08 0002 |
| Деталь: | Gear - 27Z |
| Парткод: | AB01 1390 |
| Деталь: | Roller Clutch - 6x14x10 |
| Парткод: | AA08 3018 |
| Деталь: | Magnetic Clutch:245mn.m |
| Парткод: | AX20 0292 |
| Деталь: | Pressure Plate - By-pass Feed |
| Парткод: | B004 6062 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF04 0575 |
| Деталь: | Bracket: Drive :Assy |
| Парткод: | B082 6061 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 3567 |
| Деталь: | DC Solenoid:Pickup:Sub-assy |
| Парткод: | B213 6051 |
| Деталь: | Bracket:Dc Solenoid |
| Парткод: | B213 6049 |
| Деталь: | Harness:Manual Feed Unit |
| Парткод: | B082 5427 |
| Деталь: | Arm:Tightener:Assy |
| Парткод: | B213 6059 |
| Деталь: | Gear - 24Z/30Z |
| Парткод: | AB01 7454 |
| Деталь: | SPRING |
| Парткод: | AA06 3569 |
| Деталь: | Cover:Front Upper:Paper Feed Sub-unit |
| Парткод: | B0771264 |
| Деталь: | Decal:Emblem:RIC |
| Парткод: | B195 6431 |
| Деталь: | Decal:Emblem:SVN |
| Парткод: | B195 6432 |
| Деталь: | Decal:Emblem:GES:NA |
| Парткод: | B195 6433 |
| Деталь: | Sheet:Emblem:GES:EU:DSM735 |
| Парткод: | B195 6434 |
| Деталь: | Sheet:Emblem:NSA:DSM735 |
| Парткод: | B195 6435 |
| Деталь: | Sheet:Emblem:REX:DSM735 |
| Парткод: | B195 6436 |
| Деталь: | Sheet:Emblem:INF:IS2235 |
| Парткод: | B195 6437 |
| Деталь: | Decal:Emblem:LAN |
| Парткод: | B195 6438 |
| Деталь: | Decal:Emblem:RIC |
| Парткод: | B198 6431 |
| Деталь: | Decal:Emblem:SVN |
| Парткод: | B198 6432 |
| Деталь: | Decal:Emblem:GES:NA |
| Парткод: | B198 6433 |
| Деталь: | Sheet:Emblem:GES:EU:DSM745 |
| Парткод: | B198 6434 |
| Деталь: | Sheet:Emblem:NSA:DSM745 |
| Парткод: | B198 6435 |
| Деталь: | Sheet:Emblem:REX:DSM745 |
| Парткод: | B198 6436 |
| Деталь: | Decal:Emblem:LAN |
| Парткод: | B198 6438 |
| Деталь: | Cover:Front |
| Парткод: | B2131261 |
| Деталь: | Cover:Front:EU |
| Парткод: | B198 6316 |
| Деталь: | Hinge - Front Cover |
| Парткод: | G020 1332 |
| Деталь: | Energy Decal |
| Парткод: | GA00 3035 |
| Деталь: | Sheet:Operation Instructions |
| Парткод: | B198 6405 |
| Деталь: | Stopper: Left |
| Парткод: | B077 1286 |
| Деталь: | Cover:Left:Paper Feed Sub-unit |
| Парткод: | B0771285 |
| Деталь: | Cover:Left:Eu |
| Парткод: | B077 6324 |
| Деталь: | Stopper Band |
| Парткод: | A232 2863 |
| Деталь: | Cover:Vertical Transport:Lower |
| Парткод: | B077 2876 |
| Деталь: | Decal - Right Lower Cover |
| Парткод: | AA00 0204 |
| Деталь: | Spring Plate - BICU |
| Парткод: | A232 5838 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 3564 |
| Деталь: | Supporting Plate:Lower |
| Парткод: | B077 2859 |
| Деталь: | Panel:Logo |
| Парткод: | B132 1531 |
| Деталь: | Cap - Switch |
| Парткод: | A232 1282 |
| Деталь: | Decal:Power Source:Off:Exp |
| Парткод: | B082 6403 |
| Деталь: | Cover:Left Front:NA |
| Парткод: | B077 6302 |
| Деталь: | Cover:Left Front:EU |
| Парткод: | B077 6305 |
| Деталь: | Cover:Left Rear |
| Парткод: | B077 1283 |
| Деталь: | Cover:Left Rear:EU |
| Парткод: | B077 6325 |
| Деталь: | Cover:Right Rear:Duplex |
| Парткод: | B082 1272 |
| Деталь: | Cover:Right Rear:Duplex:EU |
| Парткод: | B082 6319 |
| Деталь: | Roller:Driven:Assy |
| Парткод: | B154 2862 |
| Деталь: | Bushing:Pressure:Mm4 |
| Парткод: | AA08 0275 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3662 |
| Деталь: | Supporting Plate:Upper |
| Парткод: | B077 2858 |
| Деталь: | Entrance Seal |
| Парткод: | A232 2860 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Cover:Vertical Transport |
| Парткод: | B077 2857 |
| Деталь: | Cover:Vertical Transport:Duplex:EU |
| Парткод: | B077 2861 |
| Деталь: | Paper Tray:Universal |
| Парткод: | B213 2903 |
| Деталь: | Tray Bottom Plate:Assy |
| Парткод: | B077 2940 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3006 |
| Деталь: | Side Fence:Front:Assy |
| Парткод: | B082 2920 |
| Деталь: | Stopper:Right:Paper Tray |
| Парткод: | B077 2951 |
| Деталь: | Release Lever - Side Fence |
| Парткод: | B004 2922 |
| Деталь: | Spring Plate - Release Lever |
| Парткод: | B004 2923 |
| Деталь: | Shield:Side Fence:Assy |
| Парткод: | B082 2925 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | B082 2965 |
| Деталь: | Cover:Grip:C3 |
| Парткод: | B077 2988 |
| Деталь: | END FENCE |
| Парткод: | AF01 7026 |
| Деталь: | Shoe:Left |
| Парткод: | B077 2952 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | Gear - 16Z |
| Парткод: | B004 2936 |
| Деталь: | Side Fence:Rear:Assy |
| Парткод: | B082 2930 |
| Деталь: | Lever:Rise |
| Парткод: | B077 2975 |
| Деталь: | Rear Stopper |
| Парткод: | B004 2933 |
| Деталь: | Rear Stopper Lever |
| Парткод: | B004 2932 |
| Деталь: | Spring Plate - Lock Lever |
| Парткод: | B004 2934 |
| Деталь: | Paper Stopper:Side Fence |
| Парткод: | B082 2937 |
| Деталь: | Dial:Paper Size Sensor:Printing |
| Парткод: | B082 2955 |
| Деталь: | Paper size sensor |
| Парткод: | B004 2948 |
| Деталь: | Spring Plate-paper Size Sensor |
| Парткод: | B004 2947 |
| Деталь: | Grounding Plate - Paper Tray |
| Парткод: | B004 2943 |
| Деталь: | Shaft:Rise |
| Парткод: | B213 2915 |
| Деталь: | Feeler - Paper Height Sensor |
| Парткод: | A235 2979 |
| Деталь: | Decal:Paper Select:Dial:EXP |
| Парткод: | B213 2967 |
| Деталь: | TONER SUPPLY UNIT |
| Парткод: | B082 3209 |
| Деталь: | Seal - Slide Rail |
| Парткод: | A232 3266 |
| Деталь: | Slide Rail:Toner Supply Unit |
| Парткод: | B077 3262 |
| Деталь: | Shaft:Slide |
| Парткод: | AA14 5831 |
| Деталь: | Handle - Toner Supply |
| Парткод: | A232 3261 |
| Деталь: | Spring Plate - Toner Bottle |
| Парткод: | A232 3263 |
| Деталь: | Cover- Toner Bottle Assy |
| Парткод: | A232 3240 |
| Деталь: | Seal - Toner Supply Unit Cover |
| Парткод: | AA15 3083 |
| Деталь: | Decal:Caution Chart |
| Парткод: | B082 3265 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3566 |
| Деталь: | Chuck Shaft |
| Парткод: | A232 3251 |
| Деталь: | SLIDER ASSY |
| Парткод: | A232 3252 |
| Деталь: | Bottle Chuck |
| Парткод: | A134 3180 |
| Деталь: | Thermostat:Assy |
| Парткод: | G065 4156 |
| Деталь: | Housing:Thermostat |
| Парткод: | G065 4155 |
| Деталь: | Plate- Thermistor |
| Парткод: | B004 4087 |
| Деталь: | Thermistor:Fusing:Middle |
| Парткод: | AW10 0085 |
| Деталь: | Thermistor:Fusing:Inner Back |
| Парткод: | AW10 0086 |
| Деталь: | Stay:Fusing:Thermostat |
| Парткод: | G065 4056 |
| Деталь: | Socket:Heater:Front |
| Парткод: | B082 4111 |
| Деталь: | Frame:Fusing:Upper |
| Парткод: | B077 4081 |
| Деталь: | Tension Spring:Stripper Pawls:50mn |
| Парткод: | AA06 0948 |
| Деталь: | Stripper Pawls |
| Парткод: | AE04 4056 |
| Деталь: | Socket: Heater: Rear |
| Парткод: | B077 4115 |
| Деталь: | C Ring - Hot Roller |
| Парткод: | A232 4064 |
| Деталь: | Gear - 40Z |
| Парткод: | AB01 3882 |
| Деталь: | Ball Bearing - 30x42x7 |
| Парткод: | AE03 0047 |
| Деталь: | Hot Roller:T0.4:HB |
| Парткод: | AE01 1102 |
| Деталь: | Heater: 120V:650W:215mm |
| Парткод: | AX43 0152 |
| Деталь: | Heater:230V:650W:215mm |
| Парткод: | AX43 0153 |
| Деталь: | Heater: 120 V:650W:335mm |
| Парткод: | AX44 0173 |
| Деталь: | Heater:230V:650W:335mm |
| Парткод: | AX44 0174 |
| Деталь: | Knob:Fusing |
| Парткод: | AG05 0094 |
| Деталь: | Ball Bearing - 8x22x7 |
| Парткод: | AE03 0048 |
| Деталь: | Pressure Roller MM32 Assy |
| Парткод: | AE02 0125 |
| Деталь: | Positioning Plate Front |
| Парткод: | B082 4054 |
| Деталь: | Front Collar - Pressure Lever |
| Парткод: | A232 4057 |
| Деталь: | Lever:Pressure:Front |
| Парткод: | B213 4161 |
| Деталь: | Pressure Spring - 29n |
| Парткод: | AA06 0840 |
| Деталь: | Frame:Fusing:Assy |
| Парткод: | B082 4051 |
| Деталь: | Gear - 25Z |
| Парткод: | AB01 4046 |
| Деталь: | Rear Collar - Pressure Lever |
| Парткод: | A232 4058 |
| Деталь: | Spacer:Frame:Front |
| Парткод: | B082 4105 |
| Деталь: | Spacer:Frame:Rear |
| Парткод: | B082 4106 |
| Деталь: | Lever:Pressure:Rear |
| Парткод: | B213 4162 |
| Деталь: | Stay:Right |
| Парткод: | B0771678 |
| Деталь: | Fan Motor:15mm:24V |
| Парткод: | AX64 0164 |
| Деталь: | Bracket:Fan |
| Парткод: | B0771742 |
| Деталь: | Original Sensor:H2-66 |
| Парткод: | AW01 0114 |
| Деталь: | Bracket:Scale:Left |
| Парткод: | B082 1676 |
| Деталь: | Seal - ADF Exposure Glass |
| Парткод: | B351 6523 |
| Деталь: | Exposure Glass:Sheet Through:344x20 |
| Парткод: | BC01 2002 |
| Деталь: | Inner cover |
| Парткод: | B2131681 |
| Деталь: | Lens Unit |
| Парткод: | B2131831 |
| Деталь: | Stabilizer:Xenon Lamp |
| Парткод: | AZ50 0067 |
| Деталь: | Bracket:Hinge |
| Парткод: | B0771739 |
| Деталь: | Photointerruptor:Flat:PICH2mm:M4 |
| Парткод: | AW02 0146 |
| Деталь: | Bracket:Connector:ARDF |
| Парткод: | B0771849 |
| Деталь: | Harness:Scanner:ADF |
| Парткод: | B213 5541 |
| Деталь: | Harness:FFC:Sbu:50WICK:80mm |
| Парткод: | B213 5542 |
| Деталь: | Harness:SIB:EXP |
| Парткод: | B213 5543 |
| Деталь: | Interface Cable:Scanner |
| Парткод: | B2131841 |
| Деталь: | PCB:SIB |
| Парткод: | B213 5340 |
| Деталь: | Harness:OPU |
| Парткод: | B213 5538 |
| Деталь: | PCB:MDB |
| Парткод: | B213 5397 |
| Деталь: | Bracket:MDB:Left |
| Парткод: | B0771846 |
| Деталь: | Bracket:MDB:Right |
| Парткод: | B0771847 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0702 |
| Деталь: | Stepper Motor:Scanner |
| Парткод: | B2131751 |
| Деталь: | Ground Plate:Lensblock SMD |
| Парткод: | B2131826 |
| Деталь: | Original Sensor:H1-66 |
| Парткод: | AW01 0116 |
| Деталь: | End Fence:Copy Tray:C3 |
| Парткод: | B077 4497 |
| Деталь: | Guide:Copy Tray:Auxiliary |
| Парткод: | B077 4436 |
| Деталь: | Guide:Copy Tray |
| Парткод: | B077 4435 |
| Деталь: | Dehumidifier Sheet |
| Парткод: | AA15 3070 |
| Деталь: | Guide Plate:Scanner Unit:Peen |
| Парткод: | B0771382 |
| Деталь: | Supporting Plate:Arm:Scanner Unit |
| Парткод: | B0771384 |
| Деталь: | Arm:Scanner Unit |
| Парткод: | B0771385 |
| Деталь: | Sheet - Duct |
| Парткод: | G0651173 |
| Деталь: | Sheet - Duct - Upper |
| Парткод: | G0651174 |
| Деталь: | Cover:Rear |
| Парткод: | B077 1291 |
| Деталь: | Cover:Rear:EU |
| Парткод: | B077 6328 |
| Деталь: | Decal:Caution Chart |
| Парткод: | B082 3265 |
| Деталь: | Cover:Rear:Paper Feed Sub-unit |
| Парткод: | B082 1296 |
| Деталь: | Cover:Rear:EU |
| Парткод: | B082 6332 |
| Деталь: | Middle Guide - Paper Exit |
| Парткод: | B004 4440 |
| Деталь: | Cap - Upper Cover |
| Парткод: | A2321257 |
| Деталь: | SPRING HOLDER |
| Парткод: | A232 1284 |
| Деталь: | Cover:Rear:Paper Feed Sub-unit |
| Парткод: | B0771297 |
| Деталь: | Cover:Rear:Paper Feed Sub-unit:EU |
| Парткод: | B077 6330 |
| Деталь: | Bracket:Scanner Unit:Rear:Peen |
| Парткод: | B0771373 |
| Деталь: | Bracket:Scanner Unit:Front:Peen |
| Парткод: | B0771371 |
| Деталь: | Spacer:Scanner Unit:Duplex |
| Парткод: | B082 1362 |
| Деталь: | Spacer:Scanner Unit:Duplex:EU |
| Парткод: | B082 6342 |
| Деталь: | Plate Nut:Spacer:Scanner Unit |
| Парткод: | B0771363 |
| Деталь: | Ground Plate:Spacer:Rear |
| Парткод: | B0771364 |
| Деталь: | Ground Plate:Spacer:Front |
| Парткод: | B0771365 |
| Деталь: | InnerR Cover:Upper |
| Парткод: | B082 1372 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 1010 |
| Деталь: | Cover - Shield Glass |
| Парткод: | B0041325 |
| Деталь: | Inner Cover-left |
| Парткод: | A284 1376 |
| Деталь: | Copy Tray Mylar |
| Парткод: | A232 4499 |
| Деталь: | Total Counter:7FIG:24V |
| Парткод: | AX31 0046 |
| Деталь: | Decal - Total Counter |
| Парткод: | A232 1381 |
| Деталь: | Sponge - 202x3.5x4 |
| Парткод: | AA15 3390 |
| Деталь: | Duct - Upper Cover |
| Парткод: | A232 1252 |
| Деталь: | Seal - 215x10 |
| Парткод: | AA15 0685 |
| Деталь: | Cover:Upper Right:Small |
| Парткод: | B0771252 |
| Деталь: | Cover:Upper Right:Small:EU |
| Парткод: | B077 6312 |
| Деталь: | Stepped Screw - M8 |
| Парткод: | AA14 3501 |
| Деталь: | Cover:Upper |
| Парткод: | B077 1250 |
| Деталь: | Cover:Upper:EU |
| Парткод: | B077 6314 |
| Деталь: | Cap:34x55 |
| Парткод: | B077 1253 |
| Деталь: | Cover:Connector: Scanner |
| Парткод: | B077 1251 |
| Деталь: | Cover:Css:Exp |
| Парткод: | B077 6308 |
| Деталь: | Seal:Inner Cover:Middle |
| Парткод: | B0821373 |
| Деталь: | Seal:Inner Cover:Upper |
| Парткод: | B0821374 |
| Деталь: | Seal:Inner Cover:Left |
| Парткод: | B0821375 |
| Деталь: | Seal:Side Plate:Front:Switch |
| Парткод: | B0821379 |
| Деталь: | Inner Cover:Upper:Sub-assy |
| Парткод: | B082 1371 |
| Деталь: | Cover:Lower:Operation Sub-unit |
| Парткод: | B0771338 |
| Деталь: | Cover:Lower:Operation Sub-unit:EU |
| Парткод: | B077 6338 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Cover:Left:Scanner |
| Парткод: | B0771337 |
| Деталь: | Cover:Left:Scanner:EU |
| Парткод: | B077 6337 |
| Деталь: | Left Scale - NA |
| Парткод: | G564 6521 |
| Деталь: | Left Scale - EU |
| Парткод: | G564 6511 |
| Деталь: | Exposure Glass |
| Парткод: | AC01 2067 |
| Деталь: | Cover:Upper Rear:Scanner |
| Парткод: | B0771330 |
| Деталь: | Cover:Upper Rear:Scanner:EU |
| Парткод: | B077 6335 |
| Деталь: | Rear Scale |
| Парткод: | G5701245 |
| Деталь: | Cover:Right:Scanner |
| Парткод: | B0771336 |
| Деталь: | Cover:Right:Scanner:EU |
| Парткод: | B077 6336 |
| Деталь: | Cover:Arm:Right |
| Парткод: | B077 1276 |
| Деталь: | Cover:Arm:Scanner Unit |
| Парткод: | B0771275 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3523 |
| Деталь: | Decal:Size Indication |
| Парткод: | B082 6400 |
| Деталь: | Operating Instructions - Main NA |
| Парткод: | B138 6507 |
| Деталь: | Operating Instructions - Main |
| Парткод: | B198 6507 |
| Деталь: | Operating Instructions - Copy NA |
| Парткод: | B138 6607 |
| Деталь: | Operating Instructions - Copy |
| Парткод: | B198 6607 |
| Деталь: | Spacer:Document Feeder |
| Парткод: | B2131326 |
| Деталь: | Cloth Holder |
| Парткод: | B065 1371 |
| Деталь: | Cloth - DF Exposure Glass |
| Парткод: | B065 1374 |
| Деталь: | Decal:Power Source:Off:Exp |
| Парткод: | B082 6403 |
| Деталь: | Guide Plate:Scanner |
| Парткод: | B198 1341 |
| Деталь: | Gasket:Inner Cover |
| Парткод: | B138 5801 |
| Деталь: | Transport Roller:Drive |
| Парткод: | AF02 0648 |
| Деталь: | Vertical Transport Guide |
| Парткод: | A232 2787 |
| Деталь: | Guide Plate:Swivel:Adhesion |
| Парткод: | B082 2785 |
| Деталь: | Paper Feed Unit:No.1 |
| Парткод: | B213 2740 |
| Деталь: | PAPER FEED UNIT |
| Парткод: | B213 2750 |
| Деталь: | Bracket:Sensor |
| Парткод: | B077 2781 |
| Деталь: | Bracket:Sensor |
| Парткод: | B082 2781 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0122 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0157 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF03 0090 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 1188 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Paper Feed Roller:Feed |
| Парткод: | AF031090 |
| Деталь: | Gear - 18Z |
| Парткод: | AB01 1189 |
| Деталь: | Bushing - 8x16x7 |
| Парткод: | AA08 2070 |
| Деталь: | Pick-up Arm |
| Парткод: | A232 2763 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0691 |
| Деталь: | Front Grounding Plate |
| Парткод: | A232 2765 |
| Деталь: | Harness:Paper Feed Unit |
| Парткод: | B082 5428 |
| Деталь: | Harness:Paper Feed Unit:No.1 |
| Парткод: | B082 5430 |
| Деталь: | Feed Mylar |
| Парткод: | A232 2766 |
| Деталь: | Paper End Feeler |
| Парткод: | A232 2762 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2072 |
| Деталь: | Shaft:Separate:Drive |
| Парткод: | B213 2784 |
| Деталь: | Paper Feed Roller:Separate |
| Парткод: | AF03 2090 |
| Деталь: | TORQUE LIMITER |
| Парткод: | B004 2783 |
| Деталь: | Shaft:Separate:Driven |
| Парткод: | B213 2777 |
| Деталь: | Rear Feed Mylar |
| Парткод: | B004 2782 |
| Деталь: | Release Lever |
| Парткод: | G065 2776 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0693 |
| Деталь: | PRESSURE LEVER |
| Парткод: | G065 2774 |
| Деталь: | Gear:Separate:Driven |
| Парткод: | AB01 0157 |
| Деталь: | Gear:Separate:Drive |
| Парткод: | AB01 0156 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | LINK LEVER |
| Парткод: | G065 2775 |
| Деталь: | Release spring |
| Парткод: | AA06 0908 |
| Деталь: | Rear Grounding Plate |
| Парткод: | A232 2764 |
| Деталь: | SHAFT - PAPER FEED |
| Парткод: | AA14 0655 |
| Деталь: | Lever - Feed |
| Парткод: | G065 2767 |
| Деталь: | Stay:Feed |
| Парткод: | B077 2780 |
| Деталь: | Gear - 17Z |
| Парткод: | AB01 4275 |
| Деталь: | Inner Cover:Duplex Unit:Front |
| Парткод: | B077 4720 |
| Деталь: | Guide Plate - Middle |
| Парткод: | B004 4645 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Inner Cover:Duplex Unit:Rear |
| Парткод: | B077 4730 |
| Деталь: | Bracket:Link |
| Парткод: | B213 4793 |
| Деталь: | Cover:Harness:Duplex |
| Парткод: | B077 4810 |
| Деталь: | Screw:Inner CoverJoint Unit |
| Парткод: | B213 5843 |
| Деталь: | Exchange Pawl Cushion |
| Парткод: | AA16 1126 |
| Деталь: | Gasket - Duplex Unit |
| Парткод: | B004 5842 |
| Деталь: | Decal - Jam Removal |
| Парткод: | B004 4851 |
| Деталь: | Pressure Plate - Guide Plate |
| Парткод: | A232 4653 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA08 0034 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3303 |
| Деталь: | Roller:Driven |
| Парткод: | AF02 0653 |
| Деталь: | Driven Guide Plate |
| Парткод: | A232 4647 |
| Деталь: | Exchange Powl |
| Парткод: | AF02 5044 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0709 |
| Деталь: | Decal:Duplex Unit:Upper |
| Парткод: | B082 4853 |
| Деталь: | Cover:Duplex Unit |
| Парткод: | B077 4701 |
| Деталь: | Magnet Catch:13n |
| Парткод: | AG07 0515 |
| Деталь: | Guide Plate:Open And Close:Right |
| Парткод: | B077 4710 |
| Деталь: | Reverse Roller:Driven |
| Парткод: | AF02 0652 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0307 |
| Деталь: | Pressure Spring - Driven |
| Парткод: | AA06 0839 |
| Деталь: | Cover:Duplex Unit:Right |
| Парткод: | B077 4711 |
| Деталь: | Decal:Duplex |
| Парткод: | B082 4852 |
| Деталь: | Timing Belt - S3M-360 |
| Парткод: | AA04 3445 |
| Деталь: | Timing Pulley - 20Z |
| Парткод: | AB03 0625 |
| Деталь: | BUSHING - 6MM |
| Парткод: | GA08 0002 |
| Деталь: | Magnetic Clutch:0.5n.o70m:28z |
| Парткод: | AX20 0281 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 4219 |
| Деталь: | Bracket:Timing Pulley:Registration |
| Парткод: | B2131155 |
| Деталь: | Timing Pulley - Registration |
| Парткод: | AB03 0669 |
| Деталь: | Timing Belt - B60S3M129 |
| Парткод: | AA04 3554 |
| Деталь: | Flange - 24mm |
| Парткод: | B004 1167 |
| Деталь: | Cover - Paper Drive |
| Парткод: | A232 2692 |
| Деталь: | Holder - Optical Housing Unit |
| Парткод: | B0041938 |
| Деталь: | Timing Belt - S3M-312 |
| Парткод: | AA04 3446 |
| Деталь: | Timing Pulley - 31Z/20T |
| Парткод: | AB03 0561 |
| Деталь: | Gear - 22Z |
| Парткод: | AB01 4038 |
| Деталь: | Idler Gear-registration |
| Парткод: | AB01 4160 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0695 |
| Деталь: | Tightener:Paper Feed |
| Парткод: | B213 1149 |
| Деталь: | Spacer - By-pass Feed |
| Парткод: | B004 1177 |
| Деталь: | TIMING PULLEY - 18T |
| Парткод: | AB03 0567 |
| Деталь: | Timing Pulley - 31Z/20T |
| Парткод: | AB03 0562 |
| Деталь: | Gear - 31Z |
| Парткод: | AB01 4039 |
| Деталь: | Guide Plate:Upper |
| Парткод: | B077 1172 |
| Деталь: | Guide Plate:Lower |
| Парткод: | B077 1182 |
| Деталь: | Bracket: Protect |
| Парткод: | B213 1153 |
| Деталь: | Ball Bearing - 8x22x7 |
| Парткод: | A232 3552 |
| Деталь: | Magnetic Clutch:0.5n.m:28z |
| Парткод: | AX20 0280 |
| Деталь: | Shaft:Middle |
| Парткод: | AA14 9979 |
| Деталь: | Gear - 28T |
| Парткод: | AB01 4164 |
| Деталь: | Timing Pulley - 20T |
| Парткод: | AB03 0566 |
| Деталь: | Bracket: Middle |
| Парткод: | B0771174 |
| Деталь: | Pulley:Mm17 |
| Парткод: | B0821177 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0694 |
| Деталь: | Tightener:Middle |
| Парткод: | B2131151 |
| Деталь: | PULLEY |
| Парткод: | AB03 0634 |
| Деталь: | Base cover |
| Парткод: | B0041320 |
| Деталь: | GEAR - 29Z |
| Парткод: | AB01 4040 |
| Деталь: | Bracket:Micro Switch |
| Парткод: | B077 2882 |
| Деталь: | Gear - 49Z |
| Парткод: | AB01 4159 |
| Деталь: | PCB:MB |
| Парткод: | B213 5180 |
| Деталь: | Rack:Application |
| Парткод: | B213 5871 |
| Деталь: | Stay:Rack |
| Парткод: | B213 5876 |
| Деталь: | Panel:Fax |
| Парткод: | B198 5886 |
| Деталь: | Cover:RIO |
| Парткод: | B198 5893 |
| Деталь: | Cover:SD |
| Парткод: | B198 5894 |
| Деталь: | Cap:Connector:USB |
| Парткод: | B154 5865 |
| Деталь: | Cap - Lan Connector |
| Парткод: | B129 5008 |
| Деталь: | Panel:Control Board |
| Парткод: | B213 5851 |
| Деталь: | NVRAM-Zero Counter |
| Парткод: | B195 9590 |
| Деталь: | Bracket:Control Board:Printer |
| Парткод: | B213 5852 |
| Деталь: | Rail:Right |
| Парткод: | B622 5831 |
| Деталь: | Rail:Left |
| Парткод: | B622 5832 |
| Деталь: | PCB:Main:35 |
| Парткод: | B2135101 |
| Деталь: | PCB:Main:45 |
| Парткод: | B213 5102 |
| Деталь: | PCB:DDR-DIMM: 128MB |
| Парткод: | B584 5040 |
| Деталь: | HDD:Hitachi:40GB:Path:ROHS |
| Парткод: | B514 5990 |
| Деталь: | Keytop:Copy:1 :NA |
| Парткод: | B077 6356 |
| Деталь: | Keytop:Copy:2:NA |
| Парткод: | B077 6357 |
| Деталь: | Keytop:Copy:1 :EU |
| Парткод: | B077 6366 |
| Деталь: | Keytop:Copy:2:EU |
| Парткод: | B077 6367 |
| Деталь: | Harness:HDD |
| Парткод: | B198 5475 |
| Деталь: | Harness:HDD:Power Source |
| Парткод: | B198 5476 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3499 |
| Деталь: | Bushing:HDD |
| Парткод: | AA16 1162 |
| Деталь: | Bracket:HDD |
| Парткод: | B198 5891 |
| Деталь: | Spring Plate:HDD |
| Парткод: | B198 5892 |
| Деталь: | BUSHING |
| Парткод: | B004 4438 |
| Деталь: | Gate Pawl:Entrance |
| Парткод: | B213 4478 |
| Деталь: | EXIT ROLLER |
| Парткод: | AF02 0649 |
| Деталь: | Discharge Brush:Assy |
| Парткод: | B007 4498 |
| Деталь: | Upper Guide Plate |
| Парткод: | B004 4477 |
| Деталь: | DC Solenoid:Exit:Assy |
| Парткод: | B213 4484 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0716 |
| Деталь: | Bushing - 6x10x9mm |
| Парткод: | AA08 2058 |
| Деталь: | Cushion:Link:10x5x1.5 |
| Парткод: | AA16 1160 |
| Деталь: | Side Plate:Front |
| Парткод: | B077 4471 |
| Деталь: | Guide Roller |
| Парткод: | AF04 0574 |
| Деталь: | Exit Junction Gate |
| Парткод: | B004 4481 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Bracket: Protect: Middle |
| Парткод: | B077 4439 |
| Деталь: | Transport Roller |
| Парткод: | AF02 0658 |
| Деталь: | Pulley - 23T |
| Парткод: | AB03 0568 |
| Деталь: | Side Plate:Rear:Assy |
| Парткод: | B213 4472 |
| Деталь: | DC Solenoid:Entrance:Assy |
| Парткод: | B213 4486 |
| Деталь: | Return Spring |
| Парткод: | AA06 0855 |
| Деталь: | Gate Pawl Spring 1.5n |
| Парткод: | AA06 2313 |
| Деталь: | Lever - Entrance Junction Gate |
| Парткод: | B004 4479 |
| Деталь: | Idler pulley |
| Парткод: | AB03 0672 |
| Деталь: | Timing Belt - S2M234 |
| Парткод: | AA04 3555 |
| Деталь: | Gear Pulley - 18Z/22T |
| Парткод: | AB01 7458 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 4049 |
| Деталь: | Bracket: Belt: Plate |
| Парткод: | B082 1158 |
| Деталь: | Gear - 32Z/29T |
| Парткод: | AB030716 |
| Деталь: | Timing Belt - S3M - 180 |
| Парткод: | AA04 3571 |
| Деталь: | Gear - 30Z/18T |
| Парткод: | AB030717 |
| Деталь: | Bracket:Belt:Positioning |
| Парткод: | B2131135 |
| Деталь: | Lock Lever - Transfer Unit |
| Парткод: | A232 2372 |
| Деталь: | Tenshion Spring |
| Парткод: | AA06 2317 |
| Деталь: | Bushing - M34 |
| Парткод: | G065 1143 |
| Деталь: | Spring Clutch:On-Off |
| Парткод: | AX21 0093 |
| Деталь: | Photointerruptor:Spring Clutch |
| Парткод: | AW02 0159 |
| Деталь: | Bracket:Transfer Drive |
| Парткод: | B213 1148 |
| Деталь: | Timing Belt - B60S2M240 |
| Парткод: | AA04 3570 |
| Деталь: | Timing Pulley - Transfer Unit |
| Парткод: | AB030715 |
| Деталь: | Gear - 33Z/30T |
| Парткод: | AB01 4222 |
| Деталь: | Gear - 30Z |
| Парткод: | AB01 4223 |
| Деталь: | Fly Wheel:Dia160 |
| Парткод: | B2131189 |
| Деталь: | Flange - Fly Wheel |
| Парткод: | G0651128 |
| Деталь: | Timing Pulley - 58Z/79T |
| Парткод: | G0651122 |
| Деталь: | Timing Belt-B60S2M316 |
| Парткод: | AA04 3553 |
| Деталь: | Bracket:Holder:OPC Drum |
| Парткод: | B213 1146 |
| Деталь: | Timing Pulley - 32Z/52T |
| Парткод: | AB030714 |
| Деталь: | Holder:Opc Drum |
| Парткод: | B213 1142 |
| Деталь: | Drum Shaft |
| Парткод: | B213 1144 |
| Деталь: | Terminal Plate - Change Roller |
| Парткод: | A232 2380 |
| Деталь: | High Voltage Line:Development Vias |
| Парткод: | B213 2383 |
| Деталь: | High Voltage Line:Charge |
| Парткод: | B213 2381 |
| Деталь: | Terminal Plate - Development Bias |
| Парткод: | A232 2382 |
| Деталь: | Spring:Bias |
| Парткод: | B082 1135 |
| Деталь: | Gear:Fusing Drive Sub-unit:No.1 |
| Парткод: | AB01 4237 |
| Деталь: | Gear:Fusing Drive Sub-unit:No.2 |
| Парткод: | AB01 4238 |
| Деталь: | Bracket:Fusing Drive Sub-unit |
| Парткод: | B213 1134 |
| Деталь: | Supporting Plate:Developmen:Unit |
| Парткод: | B077 1140 |
| Деталь: | Timing Belt - B50S3M213UG |
| Парткод: | AA04 3551 |
| Деталь: | Timing Pulley:Paddle |
| Парткод: | B079 1144 |
| Деталь: | Development Drive Unit |
| Парткод: | B213 1136 |
| Деталь: | Bracket:OPC Drum:Plate |
| Парткод: | B213 1156 |
| Деталь: | Brushless Motor:Main:Assy |
| Парткод: | AX06 0330 |
| Деталь: | DC Motor:Toner Bottle |
| Парткод: | AX05 0239 |
| Деталь: | Harness:Sensor:On-off:Connecting |
| Парткод: | B082 5437 |
| Деталь: | Pickoff Pawl |
| Парткод: | A232 2343 |
| Деталь: | Holder - Pick-off Pawl |
| Парткод: | A232 2340 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 2310 |
| Деталь: | Spur |
| Парткод: | A232 2339 |
| Деталь: | Pick-off Pawl |
| Парткод: | AD02 5021 |
| Деталь: | Screw:Dia10:M3x18 |
| Парткод: | AA14 3549 |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | A232 3553 |
| Деталь: | OPC Drum |
| Парткод: | A230 9510 |
| Деталь: | Snap Ring - M6 |
| Парткод: | G065 2681 |
| Деталь: | Spring:Pressure:Cleaning Blade:No.2 |
| Парткод: | AA06 2258 |
| Деталь: | Bushing - 6x8x4mm |
| Парткод: | 52 031 852 |
| Деталь: | Cleaning Blade:No.2:Assy |
| Парткод: | AD04 1105 |
| Деталь: | Brush Roller:Cleaner:Charge:Assy |
| Парткод: | B082 2329 |
| Деталь: | RoMer:Charge:Apply |
| Парткод: | AD02 7012 |
| Деталь: | Development Unit |
| Парткод: | B213 3010 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Entrance Seal Assy |
| Парткод: | A232 3150 |
| Деталь: | Development Sleeve:Assy |
| Парткод: | B082 3100 |
| Деталь: | Shield:Development Sleeve:Front:C3 |
| Парткод: | B082 3121 |
| Деталь: | Shield:Development Sleeve:Rear:C3 |
| Парткод: | B082 3122 |
| Деталь: | Development Sleeve Gear |
| Парткод: | AB01 1386 |
| Деталь: | GEAR - 29Z |
| Парткод: | AB01 1446 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3219 |
| Деталь: | Front Cover - Development Unit |
| Парткод: | A232 3155 |
| Деталь: | Gear - 13Z |
| Парткод: | AB01 4061 |
| Деталь: | Spacer - M5 |
| Парткод: | A232 3077 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 4060 |
| Деталь: | Mylar -development Unit-right |
| Парткод: | AA15 3443 |
| Деталь: | Gear - 17Z/25Z |
| Парткод: | AB01 4062 |
| Деталь: | Entrance Shield - Toner Supply |
| Парткод: | G065 3066 |
| Деталь: | Sponge - 17x7x5 |
| Парткод: | AA15 3054 |
| Деталь: | Shield - Development - Center |
| Парткод: | AA15 3095 |
| Деталь: | Sponge - 317x5x5 |
| Парткод: | AA15 3053 |
| Деталь: | Filter:Development |
| Парткод: | AA01 2131 |
| Деталь: | Coupling Shield |
| Парткод: | G065 3067 |
| Деталь: | Rear Bias Terminal - Development |
| Парткод: | A232 3069 |
| Деталь: | Joint - Paddle |
| Парткод: | B004 3078 |
| Деталь: | Shield:Case:Development:Front Rear:C3 |
| Парткод: | B082 3123 |
| Деталь: | Tape - TD Sensor |
| Парткод: | A232 3067 |
| Деталь: | DENSITY SENSOR |
| Парткод: | B213 3065 |
| Деталь: | Front Bias Terminal - Development |
| Парткод: | A232 3068 |
| Деталь: | Ground Plate- Doctor Blade |
| Парткод: | B004 3062 |
| Деталь: | Film - Toner End Sensor Harnes |
| Парткод: | G012 3897 |
| Деталь: | Bushing - 12x18x5.5 |
| Парткод: | AA08 0281 |
| Деталь: | Film - Toner End Sensor Harnes |
| Парткод: | G012 3897 |
| Деталь: | Harness:DC:Exit |
| Парткод: | B082 5459 |
| Деталь: | Bracket:Paper Feed Sensor |
| Парткод: | B077 4494 |
| Деталь: | Harness Guide |
| Парткод: | B004 4434 |
| Деталь: | Joint:Machine Or Copier |
| Парткод: | B077 4493 |
| Деталь: | Guide Roller |
| Парткод: | AF04 0571 |
| Деталь: | Lower Guide Plate |
| Парткод: | B004 4453 |
| Деталь: | Pressure Roller:15 |
| Парткод: | AF04 0599 |
| Деталь: | Shaft:Pressure Roller |
| Парткод: | B213 4460 |
| Деталь: | Pressure Arm - Exit |
| Парткод: | B004 4458 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3854 |
| Деталь: | Arm: P ress u re: E ntra n ce |
| Парткод: | B077 4463 |
| Деталь: | Bracket:Contact Point |
| Парткод: | B213 4466 |
| Деталь: | Pressure Roller:Entrance |
| Парткод: | AF04 0601 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 2312 |
| Деталь: | Pad-guide Plate |
| Парткод: | AA16 1629 |
| Деталь: | Supporting Plate:Frame:Left Lower |
| Парткод: | B077 4437 |
| Деталь: | Frame:Left Lower |
| Парткод: | B077 4455 |
| Деталь: | Roller:Driven:9mm |
| Парткод: | AF04 0600 |
| Деталь: | Spring Plate - Exit Roller |
| Парткод: | B004 4469 |
| Деталь: | Supporting Plate:Frame:Right |
| Парткод: | B077 4490 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
Коды ошибок
101
120
121
143
144
165
302
304
321
322
323
327
328
329
335
336
337
338
350
351
352
353
354
390
391
395
401
402
403
405
440
450
490
492
501
502
503
504
506
507
510
520
541
542
543
544
545
546
547
548
557
599
601
610
611
612
620
621
623
624
626
627
630
632
633
634
635
670
672
692
700
701
722
724
725
726
727
729
730
731
732
733
734
740
741
818
819
820
821
822
823
824
826
827
828
829
838
850
851
853
854
855
856
857
860
861
863
864
865
866
867
868
870
872
873
874
875
876
880
900
901
920
925
951
953
954
955
984
985
986
990
991
992
995
997
998
999
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 143 |
| Display: | Service Call 143:Error |
| Description: | Motor |
| Causes: | • SBU defective • IPU defective • BCU defective • Harness between the SBU and IPU defective • Harness between the BCU-IPU defective • Standard white plate not installed correctly, or is dirty • Scanner mirrors and/or lenses are dirty or installed incorrectly |
| Remedy: | DC pick motor, no encoder feedback - staging motor - replace the “Staging motor” on page 4-79. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 165 |
| Description: | Out of Paper; Load Tray 1 (MPT) with [size] [type] The Tray 1 (MPT) No Paper Sensor indicates Tray 1 (MPT) is empty. |
| Causes: | • No Paper Sensor, PL5.3.14 • No Paper Sensor Actuator, PL5.3.15 • FRONT/DUP Harness, PL5.3.28 |
| Remedy: | 1 Fill Tray 1 (MPT) with paper. Does the error persist? Go to Step 2. Complete. 2 Check the following for evidence of fault or damage: • Tray 1 (MPT) No Paper Sensor, PL5.3.14 • Sensor Actuator, PL5.3.15 Is there any damage? Replace any damaged parts. Go to Step 3. 3 Test the Tray 1 (MPT) No Paper Sensor. Run the Service Diagnostics Tray 1 (MPT) No Paper Sensor test. Does the sensor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the Tray 1 (MPT) No Paper Sensor signal. Is there +3.3 V across P/J135-1 <=> P/J135-2? Replace the sensor. Go to Step 5. 5 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J135. 2. Check continuity between J13 <=> J134. Replace the Engine Control Board. Replace the FRONT/DUP Harness. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 304 |
| Display: | ERROR 304 USB INIT ERR |
| Description: | Charge AC bias error [K] The charge current less than 200 mkA is detected. |
| Causes: | Defective charge roller. Defective connectors. Disconnected harness. Defective high voltage power 1. |
| Remedy: | 1. Check the connectors. 2. Replace the PCU for black. 3. Replace the drum positioning plate. |
| Error code: | 321 |
| Display: | Turn power OFF and wait 321: MOTOR OVERHEAT |
| Description: | Printer cannot be used temporarily due to motor overheat. |
| Remedy: | Turn ON power after a while. |
| Error code: | 322 |
| Description: | Synchronization error The synchronization signal was not issued within 500 ms after the LD fired while the polygon motor was turning at the prescribed number of revolutions. |
| Causes: | • Laser synchronization board connectors or harness loose, disconnected, or damaged • Laser synchronization board defective or out of position • LD drive board defective |
| Remedy: | 1. Check the harness connection of the development HVPS. 2. Replace the development HVPS. 3. Replace the development unit. |
| Error code: | 323 |
| Display: | Open/close cover 323: Paper thickness error |
| Description: | Sensor output out of range with no media. (Only for Factory Mode) |
| Causes: | 1) Are foreign objects mixed in sensor? 2) Does printer recover when detecting paper thickness by opening/closing tray? 3) Does printer recover by power OFF/ON. |
| Remedy: | Remove foreign objects. Normal. |
| Error code: | 327 |
| Description: | LD unit home position error 1 The LD unit home position sensor did not detect the ON condition when the LD unit moved to its home position. |
| Causes: | • LD unit HP sensor/harness defective • LD unit home position sensor defective • LD positioning motor connector or harness loose, broken, defective • LD unit or LD unit motor blocked • LD unit motor defective |
| Remedy: | 1. Check if the developer in the development unit is stuck. 2. Check the development motor operation with Output Check (SP5-804-162 to -165) after the development unit has been pulled out from the machine. 3. Check the harness connection of the development motor. 4. Remove the obstruction around the development motor shaft. 5. Check if the +24V at the motor connector is ON. If not, check the following: • Check if 24V is output from the PSU-EB. • Check all harness connections on the PSU-EB. • Replace the PSU-EB. 6. Replace the development motor. |
| Error code: | 328 |
| Description: | LD unit home position error 2 The LD unit home position sensor did not detect the OFF condition when the LD unit moved from its home position. |
| Causes: | • LD unit HP sensor/harness defective • LD unit home position sensor defective • LD positioning motor connector or harness loose, broken, defective • LD unit or LD unit motor blocked • LD unit motor defective |
| Remedy: | 1. Remove the obstruction around the sub-hopper unit. 2. Replace the sub-hopper unit. |
| Error code: | 329 |
| Description: | LD unit beam pitch adjusted incorrectly The LD unit HP sensor did not detect the ON condition while changing the LD unit position to correct the LD position or change the resolution (dpi). |
| Causes: | • After initialization of the SP modes, SP2-109-3 or SP2-109-4 did not execute. • If this SC code appears at power on or during a print job, do these two SP codes then turn the main power off/on. • If executing these two SP codes does not solve the problem, check the LD unit drive mechanism (the harness of the LD board or other object could be blocking the LD drive mechanism, preventing adjustment of the pitch). • Do SP 5801, then do SP2109 3 and SP2109 4 again. |
| Error code: | 335 |
| Description: | Polygon motor error 1: On timeout The XSCRDY signal did not go LOW (Active) within 10 sec. after the polygon motor was turned on. |
| Causes: | • Polygon motor drive board I/F harness loose, disconnected, or damaged • Polygon motor drive board defective • Polygon motor defective |
| Remedy: | 1. Straighten the toner supply tube. 2. Replace the toner pump. 3. Replace the toner bottle motor, and then execute SP2-253-xxx. (-001: K, -002: C, -003: M, -004: Y, -005: YMC, -006: All colors) • When executing SP2-253-xxx, make sure the following conditions; • Fist, turn off and on the machine after opening the front left or right door. • Make sure that the target color toner bottle is installed and the toner hopper cover is close. • Enter the SP mode, and then execute SP2-253-xxx. |
| Error code: | 336 |
| Description: | Polygon motor error 2: Off timeout The XSCRDY signal did not go HIGH (Inactive) within 3 sec. after the polygon motor was turned off. |
| Causes: | • Polygon motor drive board I/F harness loose, disconnected, or damaged • Polygon motor drive board defective • Polygon motor defective |
| Error code: | 337 |
| Description: | Polygon motor error 3: XSCRDY signal error The XSCRDY signal did not go HIGH (Inactive) after the polygon motor had been rotating normally for 200 ms. |
| Causes: | • Polygon motor drive board I/F harness loose, disconnected, or damaged • Polygon motor drive board defective • Polygon motor defective |
| Error code: | 338 |
| Description: | Polygonal Mirror Motor Error 4: Unstable Timeout The XSCRDY signal was detected LOW) (Active) after the polygonal mirror motor switched on, but the signal was not detected LOW after 1 sec., and was not detected after another 500 ms. |
| Causes: | • I/F harness of the polygonal mirror motor disconnected or defective. • Polygonal mirror motor or polygonal mirror motor drive board defective. |
| Error code: | 350 |
| Description: | ID sensor error 1 One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. Vsp greater than or equals 2.5V Vsg less than 2.5 Vsp = 0V Vsg = 0 |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 351 |
| Description: | ID sensor error 2 The ID sensor output voltage is 5.0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 352 |
| Description: | ID sensor error 3 For 2 s during the ID sensor pattern check, the ID sensor pattern edge voltage is not 2.5V or the pattern edge is not detected within 800 ms. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 353 |
| Description: | ID sensor error 4 One of the following ID sensor output voltages is detected at ID sensor initialization. Vsg less than 4.0V when the maximum PWM input (255) is applied to the ID sensor. Vsg greater than or equal to 4.0V when the minimum PWM input (0) is applied to the ID sensor. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 354 |
| Display: | Set new fuser 354: Fuser life |
| Description: | Fuser life (occurs when fuser life continuation is OFF). |
| Causes: | Right after replacing fuser? |
| Remedy: | Check fuser life. Replace fuser. |
| Error code: | 390 |
| Display: | Check MP tray 390: Paper jam |
| Description: | Paper jam during paper feed from MT. |
| Causes: | Check for miss-fed paper around MT cassette. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace MT. |
| Error code: | 391 |
| Description: | TD sensor error: Auto adjust error During automatic adjustment of the TD sensor, output voltage was less than 1.8V, or more than 4.8V during TD sensor initial setting |
| Causes: | • TD sensor connector or harness loose, broken, defective • TD sensor defective • IOB defective • Toner supply defective (confirm that the toner seal strip has been removed from toner cartridge) |
| Remedy: | 1. Check the harness or harness connection. 2. Clean the surface of the quenching lamp glass. |
| Error code: | 395 |
| Description: | Development output abnormal A development bias leak signal was detected. High voltage output to the development unit exceeded the upper limit (65%) for 60 ms. |
| Causes: | • Poor connection at the development bias terminal • HVPS connectors or harnesses loose, broken, defective • HVPS defective |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 403 |
| Display: | ERROR 403 X CURRENT |
| Description: | Transfer belt position sensor error The transfer belt position sensor did not activate after the transfer belt contact clutch was switched on twice and rotated once. |
| Causes: | • Main motor malfunction • Transfer belt contact clutch defective • Transfer belt position sensor harness or connector loose, broken, defective • Transfer belt position sensor defective |
| Remedy: | 1. Check if there is no error on the print data. (Check if the same error occurs on other data?) 2. Check if it moves to the X-direction smoothly in the power-off condition. 3. Make sure no torsion on the X-bar or Y-bar. 4. Check if there is no trouble on the Timing Belt. 5. Check if there is no trouble on the Motor Cable. (disconnecting, burnout, or the like) 6. Check the FFC between each PCB and Shortconnectors connected on the PCB. 7. Replace the X-axis Motor with a new one. |
| Error code: | 405 |
| Display: | STATION ERR |
| Description: | Transfer belt error The transfer belt did not move away from the drum during the ID sensor pattern check. |
| Causes: | • Main motor malfunction • Transfer belt contact clutch defective • Transfer belt position sensor harness or connector loose, broken, defective • Transfer belt position sensor defective |
| Remedy: | 1. Execute and confirm #SENSOR TEST (ST HGT ORGN). „_ Confirm that the ON/OFF display is switched by moving the capping station up and down. 2. Check the assembly and connector connection of cap origin sensor. 3. Confirm that the maintenance station moves up and down smoothly by rotating the pulley in manual. (Check the belt tension, lubricating, etc.) 4. Replace the CAP Origin Sensor with a new one. 5. Replace the CAP Motor with a new one. 6. Replace the Station PCB with a new one. 7. Replace the Main PCB with a new one. |
| Error code: | 440 |
| Description: | Transfer Output Error. A high voltage feedback voltage of less than 0.5 V was detected for 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 450 |
| Description: | Feed Development Motor Error The PLL lock signal remained LOW for 2 s while the feed development motor was operating. |
| Causes: | • Motor lock caused by overload. • Motor drive board defective. |
| Remedy: | Replace the transfer HVPS. |
| Error code: | 490 |
| Display: | Set 490: No paper in MP tray (* stands for A4 B4, etc.) |
| Description: | ITB (Image Transfer Belt) Unit Set Error |
| Causes: | The TM sensor does not detect the reflection from the ITB. |
| Remedy: | • No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S |
| Error code: | 492 |
| Description: | High voltage power: Image transfer / paper transfer bias output error An error signal is detected for 200 ms when charging the separation, image transfer bet or paper transfer roller. |
| Causes: | High voltage leak. Broken harness Defective image transfer belt unit or paper transfer unit. Defective high voltage supply unit. |
| Remedy: | • Turn the main power switch off and on. • Reattach/replace the harness and parts on the high voltage power supply route. • Replace/reinstall the high-voltage supply unit. • Replace the high voltage supply unit. |
| Error code: | 501 |
| Display: | Service Call 501: Error |
| Description: | Tray 1 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503 |
| Display: | Service Call 503: Error |
| Description: | Tray 3 must be rebuilt |
| Causes: | (A model other than D581) Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. (D581) Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 504 |
| Description: | Tray 4 must be rebuilt |
| Causes: | The 2nd tray of D580, 1st tray of D580 when D579 and D580 are attached, the bottom D579 when two units of D579 are attached, or D631 when D581 and D631 are attached. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection D581 when D579 and D581 are attached.Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 506 |
| Display: | SYSTEM HALT (*) 506 : STATION SENS |
| Description: | Bypass must be rebuilt |
| Causes: | • Paper tray unit main motor connector or harness loose, broken, defective • Motor overload due to an obstruction • Motor defective |
| Remedy: | 1. Replace the tray 3 or 4 lift motor. 2. Replace the tray 3 or 4 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3 or 4. |
| Error code: | 507 |
| Description: | Duplex unit must be rebuilt |
| Causes: | • Feed motor defective • Feed motor connector disconnected • Obstacle interfering with mechanical movement of motor. |
| Remedy: | 1. Replace the tray 3 or 4 lift motor. 2. Replace the tray 3 or 4 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3 or 4. |
| Error code: | 510 |
| Display: | SYSTEM HALT (*) 510 : X ORGIN |
| Description: | Replace green developer |
| Causes: | • Tray lift motor defective or connector disconnected • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Remedy: | 1. Check the harness connection or replace it. 2. Replace the bypass tray lift motor. 3. Replace the bypass upper limit sensor. 4. Replace the bypass lower limit sensor. 5. Check or clear obstacles around the bypass pick-up solenoid. |
| Error code: | 520 |
| Description: | Replace optics filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 548 |
| Description: | Low Temperature Error |
| Causes: | The center thermistor detects 100°C or less for 4 seconds. |
| Remedy: | • Defective fusing lamp • Defective thermistor 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.d |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 599 |
| Description: | 1-bin Exit Motor Error (Japan Only) The transport lock sensor output does not change within 300 ms after the motor switches on. |
| Causes: | • Motor overload • Motor driver defective |
| Error code: | 601 |
| Display: | ERROR 601 INK NEAREND |
| Description: | Communication Error between BCU and MCU (D016/D097 only) One or more of the following occurred: • The BCU cannot communicate with the MCU (LCT-MF) within 100 ms after power on after 3 tries. • A BREAK signal was detected after connection between the BCU and MCU. • After a communication error, three tries to communicate with the MCU failed. |
| Causes: | • Poor connection between BCU and MCU • BCU defective • MCU defective |
| Remedy: | 1. Check or replace the harness between the BCU and MCU. 2. Replace the BCU. 3. Replace the MCU in the LCT-MF. |
| Error code: | 610 |
| Display: | ERROR 610 NOT FILLUP |
| Description: | Mechanical counter error: Bk This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 611 |
| Display: | ERROR 611 Case Weight |
| Description: | Mechanical counter error: FC This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 612 |
| Display: | ERROR 612 INK LVL LOW |
| Description: | BICU - ADF communication/command abnormal A command that cannot be executed was sent from the main machine to the ADF. |
| Causes: | • A software error, result of an abnormal procedure. |
| Remedy: | Enter the cartridge weight from "CART WEIGHT" menu of "SET UP". |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 623 |
| Description: | 2nd Paper Bank communication error An error code is issued from the paper bank unit. |
| Causes: | Loose connection. Defective paper bank. |
| Remedy: | • Reconnect the connector. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 624 |
| Description: | 4th Paper Bank (option) communication error This SC is not issued for this machine. When a communication error signal between the 3rd paper bank and 4th paper bank is received. |
| Causes: | • Loose or disconnected connector |
| Remedy: | Check the connection between the main machine and paper feed unit. |
| Error code: | 626 |
| Description: | BICU/LCT communication/timeout error After 1 data frame is sent to the LCT, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line connection unstable • External noise on the line |
| Remedy: | 1. Check the connection between the above devices. 2. Replace the RCB. 3. Replace the BCU. |
| Error code: | 627 |
| Display: | ERROR 627 INSERT CARTRIDGE |
| Description: | BICU/LCT communication/break reception error During communication with the LCT, the BICU received a break (Low) signal. |
| Causes: | • Serial line connection unstable • External noise on the line |
| Error code: | 630 |
| Description: | CSS communication error A communication error occurred during communication with the CSS. |
| Causes: | • Communication line error |
| Remedy: | Logging only. |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 633 |
| Description: | Key/card counter device error 2 During communication with the device, the MCU received a break (Low) signal. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 692 |
| Description: | GAVD block 12C bus error The I2C bus of the BICU is defective |
| Causes: | • Replace BICU |
| Error code: | 700 |
| Description: | Original stopper HP error When the pick-up motor turns on clockwise, the original stopper HP sensor does not detect the home position of the original stopper. |
| Causes: | • Detached timing belt for the pick-up motor • Defective original stopper HP sensor • Defective pick-up motor • Defective DF drive board |
| Remedy: | 1. Check the timing belt for the pick-up motor. 2. Replace the DF drive board if the pick-up motor does not work correctly. 3. Replace the pick-up motor. 4. Replace the original stopper HP sensor. |
| Error code: | 701 |
| Description: | ADF Pickup Roller Release Malfunction (D016/D097 only) The pick-up roller HP sensor does not activate or de-activate when the pick-up motor turns on. |
| Causes: | • HP sensor connector, harness loose, broken, defective • Pick-up motor connector, harness loose, broken defective • Pick-up roller HP sensor defective • Pick-up motor defective • ADF main control board defective |
| Remedy: | 1. Check the harness connections. 2. Replace the pick-up roller HP sensor. 3. Replace the pick-up motor. 4. Replace the main board of the ADF. |
| Error code: | 722 |
| Description: | Finisher jogger motor error The finisher jogger HP sensor did not return to the home position, or move out of the home position, within 1.25 sec. Staple mode cannot be used. |
| Causes: | • Jogger motor connector or harness loose, broken, defective • Jogger motor defective • Jogger HP sensor connector or harness loose, broken, defective • Jogger HP sensor defective |
| Error code: | 724 |
| Description: | Finisher staple hammer motor error Stapling does not finish within 150 ms after the staple hammer motor turned on. Staple mode cannot be used. |
| Causes: | • Staple jam • Stapler overload caused by trying to staple too many sheets • Staple hammer motor connector or harness loose, broken, defective • Staple hammer motor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the staple hammer motor HP sensor if the motor is rotating. 4. Replace the finisher main board. |
| Error code: | 725 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor. 4. Replace the finisher main board. |
| Error code: | 726 |
| Description: | Front shift jogger motor error (B703) The sides fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift jogger motor disconnected, defective • Shift jogger motor overloaded due to obstruction • Shift jogger HP sensor disconnected, defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift jogger HP sensor 4. Replace the shift jogger motor. 5. Replace the finisher main board. |
| Error code: | 727 |
| Description: | Rear shift jogger motor (B703) The side fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code |
| Causes: | Motor harness disconnected, loose, defective Motor defective Motor overload HP defective boar |
| Error code: | 729 |
| Description: | Finisher punch motor error After the punch motor is turned on, the punch HP sensor does not activate within 250 ms. |
| Causes: | • Punch motor harness or connector loose, broken, defective • Punch motor defective or overloaded due to obstruction • Punch HP sensor connector or harness loose, broken, defective • Punch HP sensor defective |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 731 |
| Description: | Finisher exit guide motor error After the finisher exit guide motor turned on, the exit guide sensor did not activate within 800 ms. |
| Causes: | • Finisher exit guide motor defective harness or connector loose, broken, defective • Finisher exit guide motor defective • Finisher exit guide sensor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the upper tray exit motor. 4. Replace the finisher main board. |
| Error code: | 732 |
| Description: | Finisher shift roller motor error The shift roller HP sensor does not activate within the prescribed time after the shift roller motor turns on. After 2 counts, the SC is logged as a jam. |
| Causes: | • Shift roller HP sensor defective • Sensor harness disconnected, defective • Shift roller motor defective • Finisher main board defective • Shift roller motor overload |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray exit motor. 4. Replace the finisher main board. |
| Error code: | 733 |
| Description: | Finisher lower tray lift motor error After the lift motor switches on to lift the tray, paper height sensor 2 does not detect the top of the paper stack, or after the motor reverses to lower the stack the top of the stack remains detected (the status of paper height sensor 1 does not change). After 2 counts, the SC is logged as a jam. |
| Causes: | • Paper height sensor 1 or 2 defective • Sensor harness disconnected, defective • Tray lift motor defective • Finisher main board defective • Tray lift motor overload |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the stapler exit motor. 4. Replace the finisher main board. |
| Error code: | 734 |
| Description: | Finisher lower tray shift motor error The lower tray did not reach the home position within 1.25 sec. after the lower tray shift motor turned on. |
| Causes: | • Lower tray shift motor connector or harness loose, broken, defective • Lower tray shift motor defective or overloaded due to an obstruction • Lower tray shift sensor harness or connector loose, broken, defective • Lower tray shift sensor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the upper tray junction gate HP sensor. 4. Replace the upper tray junction gate motor. 5. Replace the finisher main board. |
| Error code: | 740 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished after a certain time. For the 1000-sheet booklet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 741 |
| Description: | Finisher corner stapler rotation motor error The stapler does not return to its home position within the specified time after stapling. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective stapler rotation motor • Overload to the stapler rotation motor • Defective stapler rotation HP sensor |
| Remedy: | 1. Replace the stapler rotation motor. 2. Replace the stapler rotation HP sensor. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 838 |
| Display: | SYSTEM HALT (*) 838 : FW/SV MDL |
| Description: | Self-diagnostic Error 10: Clock Generator A verify error occurred when setting data was read from the clock generator via the I2C bus. |
| Causes: | • Replace the controller board |
| Error code: | 850 |
| Description: | Net I/F error Duplicate IP addresses. Illegal IP address. Driver unstable and cannot be used on the network |
| Causes: | • IP address setting incorrect • NIB (PHY) board defective • Controller board defective |
| Remedy: | Turn the main switch off and on. |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 951 |
| Description: | NVRAM Secure NVRAM Missing |
| Causes: | • Software defective • BICU defective |
| Remedy: | Replace the system board. |
| Error code: | 953 |
| Description: | NVRAM Chip Failure |
| Causes: | • Firmware bug • Update the scanner firmware • IPU defective |
| Remedy: | Indicates the NVRAM chip on the interconnect board has failed. Replace the interconnect board. |
| Error code: | 954 |
| Description: | NVRAM CRC Failure |
| Causes: | • Firmware bug • IPU defective |
| Remedy: | Indicates the NVRAM experienced a CRC failure. Replace the interconnect board. |
| Error code: | 955 |
| Description: | Code CRC <loc> |
| Causes: | • Firmware bug • Hard disk unit defective • Controller defective • MCU defective • IPU defective |
| Remedy: | Replace the system board. Where <loc> = CRC Failure or ECC Failure on the system board. |
| Error code: | 984 |
| Display: | Service call 984: Error. |
| Description: | <device> |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected |
| Remedy: | Invalid command parameter received by the specified device. Note: Service errors 980 thru 984 <device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 985 |
| Display: | Service call 985: Error |
| Description: | Transfer Belt Thermistor Error |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected |
| Remedy: | 1 Are connectors CN407 and CN411 on the sensor board connected properly? Go to step 2. Plug the connector in securely. 2 Is connector CN15 on the printer controller board connected properly? Replace the transfer belt unit. If the problem remains, replace the printer controller board. Plug the connector in securely. |
| Error code: | 986 |
| Display: | Service call 986: Error |
| Description: | Transparency (OHP) Sensor Error |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU Controller disconnected |
| Remedy: | 1 Are connectors CN4 (light emitting) and CN5 (light receiving) on the CK1 daughter board connected properly? Go to step 2. Plug the connector in securely. 2 Test the sensor. While actuating the sensor, does the voltage fluctuate between 0 V and +5 between pins 2 and 3 of connector CN7 of the printer controller board? Replace the printer controller board. Replace the MPF unit. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 995 |
| Description: | Finisher Main Feed Motor abnormal |
| Causes: | -01 D • Defective BCU • NVRAM Replacement error • Install the previous NVRAM • Input the serial number with SP5-811-004, and turn the main power switch off and on. -02 D • Defective NVRAM • Defective controller Perform SP5-825 to download the appropriate data to the NVRAM, and then turn the main power switch off and then back on. -03 D The serial number cannot be identified due to a mistake during controller replacement or mechanical failure. Replace the controller with the correct type. -04 D - Place all parts in the initial state, and then replace the parts according to the procedures described in the manuals. |
| Remedy: | 1 Is there jammed paper or other obstructions in the paper path? Clear the paper path. Go to step 2. 2 Check to ensure the connector PJ6 on the finisher control board and the feed motor assembly cable are properly connected. Are the cables properly connected? Go to step 3. Properly connect the cables. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pins 7 and 8 and +5 V dc (–10%) between pins 7 and 6 on the feed motor assembly cable connector CN1. Is either voltage missing? Go to step 4. Go to step 5. 4 Disconnect the feed motor assembly cable and PJ6 on the finisher control board. Measure continuity on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 5 Replace the feed motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 6 Measure for +24 V dc between pins 1 and 2 on connector PJ3 on the finisher control board. Measure for +5 V dc between pins 1 and 3 on PJ2 on the finisher control board. Is either voltage missing? Replace the power supply. Replace the finisher control board. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
| Error code: | 999 |
| Display: | Service call 999: Error |
| Description: | Stapler Motor Error |
| Causes: | • Color registration (MUSIC) failure |
| Remedy: | 1 Are staples jammed in the stapler? Go to step 2. Go to step 3. 2 Clear the staple jam and run the staple test in diagnostic mode or run a staple job. Does the problem reoccur? Replace the staple cartridge and to go step 4. Problem solved. 3 Are the connectors CN5 on the stapler and PJ1 on the finisher control board securely connected? Go to step 5. Securely connect the connectors. 4 Did replacement of the stapler cartridge resolve the problem? Problem resolved. Replace the stapler. 5 Make sure the finisher set switch is activated. Measure for 5 V dc between pins 11 and 12 on stapler connector CN5. Is 5 V dc present? Replace the stapler. Replace the finisher control board. 6 Did replacement of the finisher control board correct the problem? Problem solved. Go to step 7. 7 Is there continuity on the stapler to finisher control board cable? Replace the power supply. Replace the cable. |
Название
RICOH TYPE E Скрепки в картридже (4 шт.)
RICOH TYPE J Скрепки (4 комплекта+картридж)
RICOH TYPE K Скрепки с картриджем
RICOH TYPE 3210D Тонер-туба
(B0799640) RICOH TYPE 26 Девелопер
RICOH TYPE 3210D Фотобарабан
RICOH Узел фотобарабана (без барабана)
