Ricoh Aficio MPC2551

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Цветность печати	цветная
Макс. формат	A3
Размещение	напольный
Печать фотографий
Телефон
Факс
Копир
Тип устройства	МФУ
Сканер
Технология печати	лазерная
Тип	лазерный/светодиодный
Принтер
Количество цветов	4
Печать без полей
Пигментные чернила
Время разогрева	30
Двусторонняя печать
Прямая печать
Макс, разрешение для ч/б печати
По X	1 200
По Y	1 200
Скорость ч/б печати
A4	25
Копир
Шаг масштабирования	0,01
Время выхода первой копии	6,3
Макс, количество копий за цикл	999
Значение масштаба
Максимальное	4
Минимальное	0,25
Макс, разрешение (ч/б)
По Y	1 200
По Y	600
По X	600
Сканер
Отправка изображения по e-mail
Стандарт TWAIN
Устройство автоподачи оригиналов	двустороннее
Макс. формат оригинала	A3
Тип сканера	планшетный/протяжный
Емкость устройства автоподачи оригиналов	50
Разрешение сканера
По Х	1 200
Скорость сканирования
Ч/б	44
Цветн,	44
Расходные материалы
Количество картриджей	4
Печать на:
Фотобумаге
CD/DVD
Рулоне
Карточках
Матовой бумаге
Конвертах
Глянцевой бумаге
Этикетках
Пленках
Плотность бумаги
Минимальная	52
Максимальная	256
Факс
Цветной
Телефон
Спикерфон
Стандарт DECT
Автоответчик
Caller ID
АОН
Беспроводная трубка
Проводная трубка
Языки управления
PCL 5c
PCL 6
PDF
PostScript	опционально
PCL 5e
PPDS
PostScript 2
Лотки
Емкость лотка ручной подачи	100
Подача бумаги
Максимальная	1 600
Стандартная	600
Вывод бумаги
Стандартный	650
Финишер
Степлер
Брошюровщик
Сортер
Интерфейсы
Версия USB	2,0
USB
Веб-интерфейс
Ethernet (RJ-45)
FireWire (IEEE 1394)
Инфракрасный порт
LPT
Bluetooth
Wi-Fi
RS-232
Память/Процессор
Объем памяти	1 536
Емкость жесткого диска	160
Дополнительная информация
Работа от аккумулятора
Диагональ дисплея	8,5
Экран
Поддержка ОС
Linux
Windows
Mac OS
DOS
Потребляемая мощность
При работе	1 680
В режиме ожидания	118
Габариты
Глубина	676
Высота	845
Ширина	587
Вес	100

Коды ошибок

101

120

121

141

142

144

161-001

161-002

165

195

202

203

204

220

222

224

226

230

231

232

233

234

235

236

237

240

241

242

243

285

312

313

314

315

325

360

361

362

363

364

365

366

367

372

373

374

375

380

381

382

383

396

397

400

441

442

443

452

491

492

495

503

504

506

508

530

531

532

533

534

535

536

540

541

542

543

544

545

547

551

552

553

554

555

557

559

561

563

564

571

573

574

610

611

620

621

632

633

634

635

636

641

650

651

669

670

671

672

681

682

683

687

690

730

740

742

750

760

763

787

788

789

790

791

792

793

794

795

796

797

798

799

816

817

819

820

821

822

823

824

826

827

828

829

833

839

851

853

854

855, 856

857

858

859

860

861

862

863

864

865

866

867

868

870

872

873

874

875

876

877

878

880

900

920

921

990

991

992

995

997

998

Описание

Парткод

Название

RICOH TYPE S Скрепки буклетные в картридже для SR3000

RICOH TYPE T Скрепки в картридже

RICOH TYPE T Скрепки (2 упаковки)

RICOH TYPE MPC2550E Принт-картридж голубой

RICOH TYPE MPC2550E Принт-картридж пурпурный

RICOH TYPE MPC2550E Принт-картридж желтый

RICOH TYPE MPC2551HE Принт-картридж голубой

RICOH TYPE MPC2551HE Принт-картридж пурпурный

RICOH TYPE MPC2551HE Принт-картридж желтый

RICOH TYPE MPC2551E Принт-картридж черный

(D0392030) RICOH Блок фотобарабанов

(D0396401) Контейнер для отработанного тонера

RICOH Блок проявки черный

RICOH Блок проявки голубой

RICOH Блок проявки пурпурный

RICOH Блок проявки желтый

Error code:	101
Description:	Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable.
Causes:	• Long-Life Maintenance Kit, 650-4360-00
Remedy:	1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts.

Error code:	120
Display:	Service Call 120: Error
Description:	Fuser Error
Causes:	1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor.
Remedy:	Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly”

Error code:	121
Display:	Service Call 121: Error
Description:	Fuser Error
Causes:	Is cable between PU board andhighvoltage power LSI connected properly?
Remedy:	Wrong fuser lamp - BUR - replace the fuser assembly

Error code:	141
Display:	SVC 141 ERROR
Description:	Motor
Causes:	• SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective
Remedy:	DC pick motor excessive PWM - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”

Error code:	142
Display:	Contact the Service center. 142: Error
Description:	Motor
Causes:	• Standard white plate defective, dirty • Moisture inside the scanner unit • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective
Remedy:	DC pick motor, over speed - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”.

Error code:	144
Display:	ERROR 144 CARTRIDGE SET !
Description:	Motor
Causes:	• SBU defective • BCU defective • Harness between SBU and IPU defective
Remedy:	DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80.

Error code:	165
Description:	Out of Paper; Load Tray 1 (MPT) with [size] [type] The Tray 1 (MPT) No Paper Sensor indicates Tray 1 (MPT) is empty.
Causes:	• No Paper Sensor, PL5.3.14 • No Paper Sensor Actuator, PL5.3.15 • FRONT/DUP Harness, PL5.3.28
Remedy:	1 Fill Tray 1 (MPT) with paper. Does the error persist? Go to Step 2. Complete. 2 Check the following for evidence of fault or damage: • Tray 1 (MPT) No Paper Sensor, PL5.3.14 • Sensor Actuator, PL5.3.15 Is there any damage? Replace any damaged parts. Go to Step 3. 3 Test the Tray 1 (MPT) No Paper Sensor. Run the Service Diagnostics Tray 1 (MPT) No Paper Sensor test. Does the sensor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the Tray 1 (MPT) No Paper Sensor signal. Is there +3.3 V across P/J135-1 <=> P/J135-2? Replace the sensor. Go to Step 5. 5 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J135. 2. Check continuity between J13 <=> J134. Replace the Engine Control Board. Replace the FRONT/DUP Harness.

Error code:	195
Description:	Serial Number Error
Causes:	The serial number stored in the memory (EGB) is not correct.
Remedy:	EEPROM defective EGB replaced without original EEPROM

Error code:	202
Display:	ERROR 202 PARAMETER
Description:	Polygon motor error 1: ON timeout
Causes:	The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed.

Error code:	203
Display:	Power OFF/ON 203:Error ssssssssssssssss
Description:	Polygon motor error 2: OFF timeout
Causes:	The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off.

Error code:	204
Display:	Power OFF/ON 204:Error
Description:	Polygon motor error 3: XSCRDY signal error
Causes:	The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing.
Remedy:	• Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board).

Error code:	220
Display:	Service Call 220: Error
Description:	Laser Synchronizing Detection Error: [K]/[Y]
Causes:	The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally.

Error code:	222
Description:	Laser Synchronizing Detection Error: [M]/[C]
Causes:	The laser synchronizing detection signal for LDB [M]/[C] is not output after the LDB unit has turned on while the polygon motor is rotating normally.
Remedy:	• Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB 1. Check the connectors. 2. Replace the laser optics unit. 3. Replace the EGB.·

Error code:	224
Description:	Laser synchronizing detection error: start position [M]: LD0 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally.
Causes:	• Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB
Remedy:	1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU.

Error code:	230
Display:	Service Call 230: Error
Description:	Paper Jam Clear Paper Path Leave Job in Finisher area 5
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74.

Error code:	312
Description:	AC charge output error [K] The machine detects the AC charge output for each color 0.3 V or less for 0.2 seconds after the machine has started to detect the AC charge output.
Causes:	• Loosen or broken harnesses to the HVPS: C/B • Not set or broken PCDU • Defective HVPS: C/B
Remedy:	1. Close the drum securing plate firmly. 2. Make sure that the PCDU terminal plate contacts the machine terminal plate closely at the front side. 3. Set correctly or replace the PCDU. 4. Replace the harnesses to the HVPS: C/B. 5. Replace the HVPS: C/B.

Error code:	313
Description:	AC charge output error [M] The machine detects the AC charge output for each color 0.3 V or less for 0.2 seconds after the machine has started to detect the AC charge output.
Causes:	• Loosen or broken harnesses to the HVPS: C/B • Not set or broken PCDU • Defective HVPS: C/B
Remedy:	1. Close the drum securing plate firmly. 2. Make sure that the PCDU terminal plate contacts the machine terminal plate closely at the front side. 3. Set correctly or replace the PCDU. 4. Replace the harnesses to the HVPS: C/B. 5. Replace the HVPS: C/B.

Error code:	314
Description:	AC charge output error [C] The machine detects the AC charge output for each color 0.3 V or less for 0.2 seconds after the machine has started to detect the AC charge output.
Causes:	• Loosen or broken harnesses to the HVPS: C/B • Not set or broken PCDU • Defective HVPS: C/B
Remedy:	1. Close the drum securing plate firmly. 2. Make sure that the PCDU terminal plate contacts the machine terminal plate closely at the front side. 3. Set correctly or replace the PCDU. 4. Replace the harnesses to the HVPS: C/B. 5. Replace the HVPS: C/B.

Error code:	315
Description:	AC charge output error [Y] The machine detects the AC charge output for each color 0.3 V or less for 0.2 seconds after the machine has started to detect the AC charge output.
Causes:	• Loosen or broken harnesses to the HVPS: C/B • Not set or broken PCDU • Defective HVPS: C/B
Remedy:	1. Close the drum securing plate firmly. 2. Make sure that the PCDU terminal plate contacts the machine terminal plate closely at the front side. 3. Set correctly or replace the PCDU. 4. Replace the harnesses to the HVPS: C/B. 5. Replace the HVPS: C/B.

Error code:	231
Display:	Service Call 231: Error
Description:	FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts.
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	232
Display:	Service call 232: Error
Description:	FGATE ON error: Y The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [Y].
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	233
Description:	FGATE OFF error: Y • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [Y]. • The PFGATE ON signal still asserts when the next job starts.
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	234
Description:	FGATE ON error: M The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [M].
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	235
Description:	FGATE OFF error: M • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [M].
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	236
Description:	FGATE ON error: C The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [C].
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	237
Description:	FGATE OFF error: C • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [C]. • The PFGATE ON signal still asserts when the next job starts.
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	240
Display:	Service call 240: Error
Description:	LD error
Causes:	The IPU (EGB) detects a problem at the LD unit.
Remedy:	• Worn-out LD • Disconnected or broken harness of the LD. 1. Replace the laser optics unit.

Error code:	241
Display:	Service call 241:Error
Description:	LD error: Y The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization
Causes:	• Worn-out LD • Disconnected or broken harness of the LD
Remedy:	1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU.

Error code:	242
Display:	Service call 242:Error
Description:	LD error: M The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization
Causes:	• Worn-out LD • Disconnected or broken harness of the LD
Remedy:	1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU.