Ricoh Aficio MPC2800

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Цветность печати

цветная

Общие характеристики
Размещение	напольный
Цветность печати	цветная
Макс. формат	A3
Тип	лазерный/светодиодный
Технология печати	лазерная
Телефон
Факс
Печать фотографий
Сканер
Копир
Тип устройства	МФУ
Принтер
Прямая печать
Пигментные чернила
Печать без полей
Двусторонняя печать
Время разогрева	27
Макс, разрешение для ч/б печати
По Y	1 200
По X	1 200
Скорость цветной печати
A4	28
Время выхода первого отпечатка
Ч/б	5
Цветн,	8
Копир
Макс, количество копий за цикл	999
Время выхода первой копии	8
Шаг масштабирования	0,01
Значение масштаба
Минимальное	0,25
Максимальное	4
Макс, разрешение (ч/б)
По X	600
По Y	600
По Y	1 200
Сканер
Стандарт TWAIN
Устройство автоподачи оригиналов	двустороннее
Тип сканера	планшетный/протяжный
Макс. формат оригинала	A3
Емкость устройства автоподачи оригиналов	50
Макс, размер сканирования
По X	297
По Y	420
Разрешение сканера
По Х	1 200
Расходные материалы
Количество картриджей	4
Печать на:
Рулоне
CD/DVD
Фотобумаге
Пленках
Матовой бумаге
Конвертах
Глянцевой бумаге
Этикетках
Карточках
Плотность бумаги
Минимальная	60
Максимальная	256
Факс
Цветной
Телефон
Спикерфон
АОН
Беспроводная трубка
Проводная трубка
Caller ID
Автоответчик
Стандарт DECT
Языки управления
PCL 6
PCL 5c
PostScript 3
PostScript 2
PPDS
PostScript
PCL 5e
PDF
Лотки
Подача бумаги
Максимальная	4 400
Стандартная	1 200
Вывод бумаги
Стандартный	1 625
Финишер
Электронная сортировка
Сортер
Брошюровщик
Степлер
Сортировка со сдвигом
Интерфейсы
Ethernet (RJ-45)
Веб-интерфейс
USB
Bluetooth
Устройство для чтения карт памяти
Wi-Fi
FireWire (IEEE 1394)
LPT
Инфракрасный порт
RS-232
Версия USB	2,0
Память/Процессор
Емкость жесткого диска	80
Объем памяти	1 024
Дополнительная информация
Поддержка ОС
DOS
Mac OS
Windows
Linux
Потребляемая мощность
В режиме ожидания	106
При работе	1 600
Габариты
Вес	120
Высота	760
Ширина	670
Глубина	671

Коды ошибок

101

120

121

141

142

144

161-001

161-002

165

195

202

203

204

210

211

212

213

220

222

224

226

230

231

232

233

234

235

236

237

240

241

242

243

285

300

301

302

303

360

361

362

363

364

365

366

367

372

373

374

375

380

381

382

383

396

397

398

399

400

441

442

443

452

460

490

491

492

498

501

502

503-01

503-02

504-01

504-02

505-1

505-2

530

531

532

533

534

535

536

540

541

542

543

544

545

547

551

552

553

554

555

557

559

561

563

564

565

610

611

620

621

622

623

632

633

634

635

636

641

650

651

669

670

671

672

681

682

683

687

690

725

730

740

742

746

750

760

761

763

764

765

766

770

791

792

798-1

798-2

798-3

798-4

798-5

798-6

798-7

798-8

798-9

816

819

820

833

851

853

854

855, 856

857

858

859

860

861

863

864

865

866

867

868

870

872

873

874

875

876

877

878

880

900

910...914

919

920

921

990

991

992

994

995

997

998

Описание

Парткод

Название

RICOH TYPE K Скрепки с картриджем

RICOH TYPE K Скрепки (3 упаковки)

RICOH TYPE S Скрепки буклетные в картридже для SR3000

(842043) RICOH TYPE MPC3300E Принт-картридж черный

(842044) RICOH TYPE MPC3501E/MPC3300E Принт-картридж желтый

(842045) RICOH TYPE MPC3501E/MPC3300E Принт-картридж пурпурный

(842046) RICOH TYPE MPC3501E/MPC3300E Принт-картридж голубой

RICOH Девелопер черный

RICOH Девелопер голубой

RICOH Девелопер пурпурный

RICOH Девелопер желтый

(D0292039) RICOH Блок фотобарабана цветной CMY

RICOH Блок фотобарабана черный

RICOH Блок проявки черный

RICOH Блок проявки голубой

RICOH Блок проявки пурпурный

RICOH Блок проявки желтый

RICOH Бункер отработанного тонера

Error code:	101
Description:	Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable.
Causes:	• Long-Life Maintenance Kit, 650-4360-00
Remedy:	1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts.

Error code:	120
Display:	Service Call 120: Error
Description:	Fuser Error
Causes:	1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor.
Remedy:	Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly”

Error code:	121
Display:	Service Call 121: Error
Description:	Fuser Error
Causes:	Is cable between PU board andhighvoltage power LSI connected properly?
Remedy:	Wrong fuser lamp - BUR - replace the fuser assembly

Error code:	141
Display:	SVC 141 ERROR
Description:	Motor
Causes:	• SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective
Remedy:	DC pick motor excessive PWM - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”

Error code:	142
Display:	Contact the Service center. 142: Error
Description:	Motor
Causes:	• Standard white plate defective, dirty • Moisture inside the scanner unit • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective
Remedy:	DC pick motor, over speed - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”.

Error code:	144
Display:	ERROR 144 CARTRIDGE SET !
Description:	Motor
Causes:	• SBU defective • BCU defective • Harness between SBU and IPU defective
Remedy:	DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80.

Error code:	165
Description:	Out of Paper; Load Tray 1 (MPT) with [size] [type] The Tray 1 (MPT) No Paper Sensor indicates Tray 1 (MPT) is empty.
Causes:	• No Paper Sensor, PL5.3.14 • No Paper Sensor Actuator, PL5.3.15 • FRONT/DUP Harness, PL5.3.28
Remedy:	1 Fill Tray 1 (MPT) with paper. Does the error persist? Go to Step 2. Complete. 2 Check the following for evidence of fault or damage: • Tray 1 (MPT) No Paper Sensor, PL5.3.14 • Sensor Actuator, PL5.3.15 Is there any damage? Replace any damaged parts. Go to Step 3. 3 Test the Tray 1 (MPT) No Paper Sensor. Run the Service Diagnostics Tray 1 (MPT) No Paper Sensor test. Does the sensor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the Tray 1 (MPT) No Paper Sensor signal. Is there +3.3 V across P/J135-1 <=> P/J135-2? Replace the sensor. Go to Step 5. 5 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J135. 2. Check continuity between J13 <=> J134. Replace the Engine Control Board. Replace the FRONT/DUP Harness.

Error code:	195
Description:	Serial Number Error
Causes:	The serial number stored in the memory (EGB) is not correct.
Remedy:	EEPROM defective EGB replaced without original EEPROM

Error code:	202
Display:	ERROR 202 PARAMETER
Description:	Polygon motor error 1: ON timeout
Causes:	The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed.

Error code:	203
Display:	Power OFF/ON 203:Error ssssssssssssssss
Description:	Polygon motor error 2: OFF timeout
Causes:	The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off.

Error code:	204
Display:	Power OFF/ON 204:Error
Description:	Polygon motor error 3: XSCRDY signal error
Causes:	The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing.
Remedy:	• Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board).

Error code:	210
Description:	EM Null page cargo
Causes:	• Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB
Remedy:	1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU.

Error code:	211
Display:	ERROR 211 HeadWARM.THERM(----)
Description:	EM Null page
Causes:	• Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB
Remedy:	1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU.

Error code:	212
Description:	Install or Reseat Imaging Unit The Imaging Unit CRUM fails to detect the Imaging Unit.
Causes:	• Imaging Unit, PL6.1.1 • CRUM Connector, PL7.1.4 • PHD2 Harness, PL7.1.7 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Remove the Imaging Unit. Inspect the printer cavity for damage, debris, and toner under the auger area preventing the Imaging Unit from being seated properly. Is there foreign material or damage? Remove foreign material. Vacuum out loose toner if found. Go to Step 2. 2 Inspect and reseat the Imaging Unit. Does the error persist?. Go to Step 3. Complete 3 Check Imaging Unit CRUM connection. Are P/J710 and P/J484 connected? Go to Step 4. Reconnect the CRUM. 4 Check all pins on the PHD2 Harness PL7.1.7 for continuity. 1. Disconnect P/J710 and P/J484. 2. Check continuity between J484<=>J710. Go to Step 5 Replace PHD2 Harness. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J484 and P/J48. 2. Check continuity between J48 <=> P484. Go to Step 6 Replace the FAN/PHD/MOT Harness 6 Replace the Imaging Unit. Does the error persist? Replace the Engine Control Board. Complete

Error code:	213
Display:	Power OFF/ON 213:Error
Description:	Install or Reseat Transfer Roller The printer does not detect the presence of the Transfer Roller.
Causes:	• CTD (ADC) Sensor, PL5.2.19 • Transfer Roller, PL5.1.4 • FSR/ADC Harness, PL5.2.28
Remedy:	1 Check the following for evidence of fault or damage: • Transfer Roller PL5.1.4 • CTD (ADC) Sensor PL5.2.19 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Clean the CTD (ADC) Sensor. Does this fix the problem? Complete Go to Step 3. 3 Test the CTD (ADC) Sensor. Run the Service Diagnostics CTD (ADC) Sensor test. Does the sensor function correctly? Go to Step 4. Go to Step 5. 4 Replace the Transfer Roller. Does the error persist? Go to Step 5. Complete 5 Check the CTD (ADC) Sensor connection. Is P/J136 connected to the harness? Go to Step 6. Connect the sensor. 6 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J136. 2. Check continuity between J36 <=> J136. Go to Step 7. Replace the FSR/ ADC Harness. 7 Check the CTD (ADC) Sensor signal. Disconnect P/J36. Does J36-2 <=> J36-5 = 0 V? Replace the CTD (ADC) Sensor. Replace the Engine Control Board.

Error code:	230
Display:	Service Call 230: Error
Description:	Paper Jam Clear Paper Path Leave Job in Finisher area 5
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74.

Error code:	303
Display:	SYSTEM HALT (*) 303 : PCB MAIN ET
Description:	AC charge output error [Y] The measured voltage is not proper when IOB measures the charge output for each color.
Causes:	• Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply
Remedy:	1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply.

Error code:	220
Display:	Service Call 220: Error
Description:	Laser Synchronizing Detection Error: [K]/[Y]
Causes:	The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally.

Error code:	222
Description:	Laser Synchronizing Detection Error: [M]/[C]
Causes:	The laser synchronizing detection signal for LDB [M]/[C] is not output after the LDB unit has turned on while the polygon motor is rotating normally.
Remedy:	• Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB 1. Check the connectors. 2. Replace the laser optics unit. 3. Replace the EGB.·

Error code:	224
Description:	Laser synchronizing detection error: start position [M]: LD0 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally.
Causes:	• Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB
Remedy:	1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU.

Error code:	231
Display:	Service Call 231: Error
Description:	FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts.
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	232
Display:	Service call 232: Error
Description:	FGATE ON error: Y The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [Y].
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	233
Description:	FGATE OFF error: Y • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [Y]. • The PFGATE ON signal still asserts when the next job starts.
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	234
Description:	FGATE ON error: M The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [M].
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	235
Description:	FGATE OFF error: M • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [M].
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	236
Description:	FGATE ON error: C The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [C].
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Error code:	237
Description:	FGATE OFF error: C • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [C]. • The PFGATE ON signal still asserts when the next job starts.
Causes:	• Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB
Remedy:	1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.