Ricoh CL3100DN
Рейтинг
Модули
CASSETTE 2
FUSING UNIT
FRONT DOOR
Electrical
Paper exit
DRIVE SECTION
Toner cartridge drive
CASSETTE 1
EXTERIOR 3
LSU/IH UNIT
PAPER FEED UNIT
EXTERIOR 2
ENGIN CONTROL BOARD
TRANSFER BELT TENSION UNIT
BIAS TERMINAL
EXTERIOR 1
Детали DRIVE SECTION
| Деталь: | Paper Guide - Paper Feed Unit |
| Парткод: | G081 2501 |
| Деталь: | Cassette Base Palte |
| Парткод: | G081 2521 |
| Деталь: | Spring - Base Plate |
| Парткод: | G342 1136 |
| Деталь: | Side Pressure Spring |
| Парткод: | G081 2504 |
| Деталь: | Left Corner Separator |
| Парткод: | G081 2505 |
| Деталь: | Left Paper Side Guide |
| Парткод: | G081 2506 |
| Деталь: | SPRING |
| Парткод: | G081 2522 |
| Деталь: | SLIDER |
| Парткод: | G081 2508 |
| Деталь: | Left Lift Plate |
| Парткод: | G081 2509 |
| Деталь: | BUSHING |
| Парткод: | G081 2510 |
| Деталь: | Plastic Washer |
| Парткод: | G081 2511 |
| Деталь: | Paper Size Selector |
| Парткод: | G081 2512 |
| Деталь: | Right Lift Plate |
| Парткод: | G081 2513 |
| Деталь: | CASSETTE BASE |
| Парткод: | G081 2514 |
| Деталь: | Right Coner Sperater |
| Парткод: | G081 2515 |
| Деталь: | Right Paper Side Guide |
| Парткод: | G081 2516 |
| Деталь: | RACK |
| Парткод: | G081 2517 |
| Деталь: | PINION GEAR |
| Парткод: | G081 2518 |
| Деталь: | Paper Size Adjuster |
| Парткод: | G081 2519 |
| Деталь: | Screw 3x8 |
| Парткод: | G081 4523 |
| Деталь: | Paper Size Selector Support |
| Парткод: | G081 2520 |
| Деталь: | PAPER GUIDE |
| Парткод: | G081 4001 |
| Деталь: | Left Spring - Guide Plate |
| Парткод: | G081 4002 |
| Деталь: | Right Spring - Guide Plate |
| Парткод: | G081 4003 |
| Деталь: | Upper Stay |
| Парткод: | G120 4001 |
| Деталь: | Guide Support Band |
| Парткод: | G081 4005 |
| Деталь: | Actuator - Fusing |
| Парткод: | G081 4006 |
| Деталь: | Actuator - Support Plate |
| Парткод: | G081 4007 |
| Деталь: | ACTUATOR SPRING |
| Парткод: | G081 4008 |
| Деталь: | Actuator Spring B |
| Парткод: | G081 4009 |
| Деталь: | Paper Separater |
| Парткод: | G081 4010 |
| Деталь: | Right Spring - Separater |
| Парткод: | G081 4011 |
| Деталь: | Left Spring - Separater |
| Парткод: | G081 4012 |
| Деталь: | Fusing Belt |
| Парткод: | G081 4013 |
| Деталь: | Heat Roll Frange |
| Парткод: | G120 4003 |
| Деталь: | Support Ring |
| Парткод: | G081 4015 |
| Деталь: | HEAT ROLLER |
| Парткод: | G120 4004 |
| Деталь: | Heat Roller Shaft |
| Парткод: | G081 4017 |
| Деталь: | THERMISTOR ASSY |
| Парткод: | G081 4018 |
| Деталь: | Thermistor Holder |
| Парткод: | G081 4019 |
| Деталь: | Thermistor Stay |
| Парткод: | G081 4020 |
| Деталь: | FUSING ROLLER |
| Парткод: | G081 4021 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | G120 4005 |
| Деталь: | Heat Roller Bearing |
| Парткод: | G081 4023 |
| Деталь: | Heat Roller Bush |
| Парткод: | G081 4024 |
| Деталь: | PRESSURE SPRING |
| Парткод: | G120 4006 |
| Деталь: | RIGHT FRAME |
| Парткод: | G120 4007 |
| Деталь: | Right Pressure Plate |
| Парткод: | G081 4028 |
| Деталь: | Right Release Lever |
| Парткод: | G120 4008 |
| Деталь: | SCREW |
| Парткод: | G120 4013 |
| Деталь: | Left Pressure Plate |
| Парткод: | G081 4031 |
| Деталь: | Left Release Lever |
| Парткод: | G120 4009 |
| Деталь: | Left Frame |
| Парткод: | G120 4010 |
| Деталь: | Left Grounding Plate |
| Парткод: | G081 4034 |
| Деталь: | Pressure Roll Gear Z30 |
| Парткод: | G081 4035 |
| Деталь: | BELT TENSION SPRING |
| Парткод: | G081 4036 |
| Деталь: | Gear - Z18 |
| Парткод: | G081 4037 |
| Деталь: | Rotatation Plate |
| Парткод: | G081 4038 |
| Деталь: | Fusing Board |
| Парткод: | G081 4039 |
| Деталь: | Harness - Fusing |
| Парткод: | G081 4040 |
| Деталь: | Stay Stopper |
| Парткод: | G081 4041 |
| Деталь: | Right Grounding Plate |
| Парткод: | G081 4042 |
| Деталь: | Fusing Base |
| Парткод: | G120 4011 |
| Деталь: | Base Shutter |
| Парткод: | G081 4044 |
| Деталь: | Right Shutter Spring |
| Парткод: | G081 4045 |
| Деталь: | Left Shutter Spring |
| Парткод: | G081 4046 |
| Деталь: | E-ring |
| Парткод: | G081 4538 |
| Деталь: | E-ring |
| Парткод: | G081 4529 |
| Деталь: | PIN |
| Парткод: | G081 2282 |
| Деталь: | Screw - 2.6x10 |
| Парткод: | G081 4540 |
| Деталь: | WASHER |
| Парткод: | G081 4555 |
| Деталь: | Screw 3x10 |
| Парткод: | G081 4517 |
| Деталь: | Screw 2x8 |
| Парткод: | G081 4539 |
| Деталь: | WASHER |
| Парткод: | G081 4554 |
| Деталь: | Paper Guide Plate |
| Парткод: | G081 4047 |
| Деталь: | Stay Shaft |
| Парткод: | G120 4012 |
| Деталь: | FRONT COVER ASSEMBLY |
| Парткод: | G081 1301 |
| Деталь: | Lock Lever Spring |
| Парткод: | G081 1302 |
| Деталь: | Lock Lever - Front Cover |
| Парткод: | G081 1303 |
| Деталь: | Paper Guide - Transfer Roller |
| Парткод: | G081 1310 |
| Деталь: | Plastic Belt |
| Парткод: | G081 1305 |
| Деталь: | Plate - Transfer Roller |
| Парткод: | G081 1306 |
| Деталь: | Spring - Transfer Roller |
| Парткод: | G081 1307 |
| Деталь: | Right Bushing - Transfer Roller |
| Парткод: | G081 1308 |
| Деталь: | Left Bushing - Transfer Roller |
| Парткод: | G081 1309 |
| Деталь: | Paper Guide - Transfer Roller |
| Парткод: | G081 1315 |
| Деталь: | Screw 3x12 |
| Парткод: | G081 4519 |
| Деталь: | Emblem - Cl3000E |
| Парткод: | G120 2310 |
| Деталь: | Emblem - CLP18 |
| Парткод: | G120 2311 |
| Деталь: | Emblem - C7417 |
| Парткод: | G120 2312 |
| Деталь: | Emblem - LP122C |
| Парткод: | G120 2313 |
| Деталь: | Emblem - Cl3100 |
| Парткод: | G120 2314 |
| Деталь: | Emblem - LP121C |
| Парткод: | G120 2315 |
| Деталь: | Emblem - C7417:NAS |
| Парткод: | G120 2316 |
| Деталь: | Emblem - C7417:REX |
| Парткод: | G120 2317 |
| Деталь: | Emblem - C7417:GES |
| Парткод: | G120 2318 |
| Деталь: | Emblem - Cl2000 |
| Парткод: | G121 2316 |
| Деталь: | Emblem - C7416:NAS |
| Парткод: | G121 2317 |
| Деталь: | Emblem - C7416:REX |
| Парткод: | G121 2318 |
| Деталь: | Emblem - C7416:GES |
| Парткод: | G121 2319 |
| Деталь: | Emblem - Cl2000N |
| Парткод: | G122 2310 |
| Деталь: | Emblem - CLP17 |
| Парткод: | G122 2311 |
| Деталь: | Emblem - C7416 |
| Парткод: | G122 2312 |
| Деталь: | Emblem - LP116C |
| Парткод: | G122 2313 |
| Деталь: | Emblem - Cl3100DN |
| Парткод: | G123 2320 |
| Деталь: | Emblem - LP121CX |
| Парткод: | G123 2321 |
| Деталь: | Emblem - C7417DN:NAS |
| Парткод: | G123 2322 |
| Деталь: | Emblem - C7417DN:REX |
| Парткод: | G123 2323 |
| Деталь: | Emblem - C7417DN:GES |
| Парткод: | G123 2324 |
| Деталь: | Trasfer Roller Assembly |
| Парткод: | G120 1301 |
| Деталь: | Front Door Support Plate |
| Парткод: | G081 1313 |
| Деталь: | Screw - 3x10 |
| Парткод: | G081 4517 |
| Деталь: | GROUNDING PLATE |
| Парткод: | G081 1314 |
| Деталь: | Screw - 2.6x6 |
| Парткод: | G081 4542 |
| Деталь: | High Voltage Boade |
| Парткод: | G081 5123 |
| Деталь: | Cover - High Voltage Board |
| Парткод: | G081 2436 |
| Деталь: | Granding Plate |
| Парткод: | G081 2437 |
| Деталь: | Granding Plate |
| Парткод: | G081 2438 |
| Деталь: | Cover - Main Control Board |
| Парткод: | G081 2439 |
| Деталь: | Base - Main Control Board |
| Парткод: | G081 2440 |
| Деталь: | Guide Rail - MCB |
| Парткод: | G081 2441 |
| Деталь: | Main Controller Board (G120-17/G123-22 27) |
| Парткод: | G125 5742 |
| Деталь: | Main Controller Board (G120-22 27) |
| Парткод: | G125 5752 |
| Деталь: | Main Controller Board (G122-17) |
| Парткод: | G125 5762 |
| Деталь: | Main Controller Board (G121-17 27 22 69) |
| Парткод: | G125 5772 |
| Деталь: | Grip - MCB Bracket |
| Парткод: | G081 5853 |
| Деталь: | Cover - Power Supply Unit |
| Парткод: | G081 2442 |
| Деталь: | Duct - Power Supply Unit |
| Парткод: | G081 2443 |
| Деталь: | IH Power Supply Board (120V) |
| Парткод: | G081 5131 |
| Деталь: | IH Power Supply Board (230V) |
| Парткод: | G081 5132 |
| Деталь: | Ih Power Supply Board - 200V G121-69 |
| Парткод: | G120 5151 |
| Деталь: | Power Supply Unit (120V) |
| Парткод: | G081 5151 |
| Деталь: | Power Supply Unit (230V) |
| Парткод: | G081 5154 |
| Деталь: | Power Supply 200V G121-69 |
| Парткод: | G120 5152 |
| Деталь: | HARNESS |
| Парткод: | G081 5430 |
| Деталь: | Harness -120V |
| Парткод: | G081 5431 |
| Деталь: | Harness -230V |
| Парткод: | G081 5433 |
| Деталь: | Base - Power Supply Unit |
| Парткод: | G081 2444 |
| Деталь: | SPRING |
| Парткод: | G081 2445 |
| Деталь: | Sensor - Color Registration |
| Парткод: | G081 5317 |
| Деталь: | HARNESS |
| Парткод: | G081 2446 |
| Деталь: | Registration Sensor Shutter |
| Парткод: | G081 2498 |
| Деталь: | Bottom Stay |
| Парткод: | G081 2448 |
| Деталь: | RUBBER FOOT |
| Парткод: | G081 2449 |
| Деталь: | Screw 3x6 |
| Парткод: | G081 4522 |
| Деталь: | Screw 3x8 |
| Парткод: | G081 4524 |
| Деталь: | Screw 3x12 |
| Парткод: | G081 4519 |
| Деталь: | Tapping Screw - M3x5 |
| Парткод: | 0451 3005B |
| Деталь: | WASHER |
| Парткод: | G081 4551 |
| Деталь: | Ground Plate - PSU |
| Парткод: | G081 2488 |
| Деталь: | Harness - Str |
| Парткод: | G081 5436 |
| Деталь: | Rip Lock Screw A (With NIC) |
| Парткод: | G081 4556 |
| Деталь: | Stay - MCB Bracket |
| Парткод: | G081 5851 |
| Деталь: | Stay - MCB Bracket (With NIC) |
| Парткод: | G081 5871 |
| Деталь: | Bracket - Main Ccontroller Board |
| Парткод: | G081 5852 |
| Деталь: | SDRAM 64MB 133 |
| Парткод: | G330 5700 |
| Деталь: | USB Board |
| Парткод: | B525 5660 |
| Деталь: | IEEE 1284 Board |
| Парткод: | B463 5700 |
| Деталь: | Thirmistor |
| Парткод: | G081 5201 |
| Деталь: | Recovery Grand Spring |
| Парткод: | G081 2491 |
| Деталь: | Paper Tray Assy |
| Парткод: | G081 2494 |
| Деталь: | Rip Lock Screw B |
| Парткод: | G081 4557 |
| Деталь: | Paper Exit Roller Joint Gear |
| Парткод: | G081 2375 |
| Деталь: | Rotation Switching Gear - A |
| Парткод: | G081 2376 |
| Деталь: | Rotation Switching Gear - B |
| Парткод: | G081 2377 |
| Деталь: | Outer Gear |
| Парткод: | G081 2378 |
| Деталь: | Intermediate Gear |
| Парткод: | G081 2379 |
| Деталь: | Double Teeth Gear |
| Парткод: | G081 2380 |
| Деталь: | Inner Gear |
| Парткод: | G081 2403 |
| Деталь: | Coupling Gear |
| Парткод: | G081 2381 |
| Деталь: | Switching Lever Spring |
| Парткод: | G081 2338 |
| Деталь: | Switching Lever |
| Парткод: | G081 2339 |
| Деталь: | Solenoid - DC24V-3.6W |
| Парткод: | G081 5324 |
| Деталь: | Paper Exit Gear Cover |
| Парткод: | G081 2340 |
| Деталь: | Holder - Paper Exit Roller |
| Парткод: | G081 2342 |
| Деталь: | Pinch Roller - A |
| Парткод: | G081 2343 |
| Деталь: | PINCH ROLLER SPRING |
| Парткод: | G081 2344 |
| Деталь: | Pinch Roller - B |
| Парткод: | G081 2345 |
| Деталь: | Star Rubber |
| Парткод: | G081 2346 |
| Деталь: | Discharge Brush |
| Парткод: | G081 2347 |
| Деталь: | Exit Paper Guide |
| Парткод: | G081 2348 |
| Деталь: | SPRING |
| Парткод: | G081 2349 |
| Деталь: | Actuator - Paper Full Sensor |
| Парткод: | G081 2350 |
| Деталь: | Sesor - Paper Jam |
| Парткод: | G081 5313 |
| Деталь: | Sensor - Paper Full/Jam |
| Парткод: | G081 5314 |
| Деталь: | PAPER EXIT ROLLER |
| Парткод: | G081 2351 |
| Деталь: | Exit Roller Rubber |
| Парткод: | G081 2352 |
| Деталь: | Screw 3x6 |
| Парткод: | G081 4522 |
| Деталь: | Screw 3x12 |
| Парткод: | G081 4519 |
| Деталь: | Paper Stoper - B |
| Парткод: | G081 2353 |
| Деталь: | Paper Stoper - A |
| Парткод: | G081 2354 |
| Деталь: | Paper Exit Roller Assembly |
| Парткод: | G081 2355 |
| Деталь: | Motor - DC24V-40.56W |
| Парткод: | G120 5201 |
| Деталь: | Motor - DC24V-31.63W |
| Парткод: | G081 5213 |
| Деталь: | Bk Solenoid |
| Парткод: | G120 2202 |
| Деталь: | Bk Change Gear 2 |
| Парткод: | G120 2203 |
| Деталь: | Clutch Bearing 2 |
| Парткод: | G120 2204 |
| Деталь: | Feed Idle Gear |
| Парткод: | G081 2103 |
| Деталь: | Fuser Idle Gear |
| Парткод: | G081 2104 |
| Деталь: | Cam Gear |
| Парткод: | G081 2105 |
| Деталь: | Left - PCU Idle Gear |
| Парткод: | G081 2106 |
| Деталь: | Right - PCU Idle Gear |
| Парткод: | G081 2107 |
| Деталь: | Left - Transfer Belt Idle Gear |
| Парткод: | G081 2108 |
| Деталь: | Right - Transfer Belt Idle Gear |
| Парткод: | G081 2109 |
| Деталь: | PCU Gear |
| Парткод: | G081 2145 |
| Деталь: | Devloper Coupling |
| Парткод: | G081 2111 |
| Деталь: | Devloper Spring |
| Парткод: | G081 2112 |
| Деталь: | Developer Gear |
| Парткод: | G081 2146 |
| Деталь: | Clutch Spacer |
| Парткод: | G120 2205 |
| Деталь: | Granding Plate - Transfer Belt |
| Парткод: | G081 2115 |
| Деталь: | CMY Home Lever |
| Парткод: | G081 2116 |
| Деталь: | PCU Home Spring |
| Парткод: | G081 2117 |
| Деталь: | PCU Home Lever |
| Парткод: | G081 2118 |
| Деталь: | Sensor - PCU Cam Home Position |
| Парткод: | G081 5305 |
| Деталь: | Bushing - Transfer Belt |
| Парткод: | G081 2119 |
| Деталь: | Bracket - Drive Unit |
| Парткод: | G120 2101 |
| Деталь: | Feed Pulley Gear |
| Парткод: | G081 2121 |
| Деталь: | Pulley Gear - Transfer Belt |
| Парткод: | G120 2102 |
| Деталь: | Feed Belt |
| Парткод: | G081 2123 |
| Деталь: | Tension Roller |
| Парткод: | G081 2124 |
| Деталь: | Flange - Feed Pulley Gear |
| Парткод: | G081 2125 |
| Деталь: | Flange - Transfer Belt Pulley Gear |
| Парткод: | G081 2126 |
| Деталь: | CMY Change Gear |
| Парткод: | G081 2127 |
| Деталь: | Screw 3x6 |
| Парткод: | G081 4522 |
| Деталь: | Screw 3x8 |
| Парткод: | G081 4532 |
| Деталь: | Screw 3x8 |
| Парткод: | G120 4501 |
| Деталь: | E-ring |
| Парткод: | G081 4529 |
| Деталь: | Main Drive Unit Assy |
| Парткод: | G120 2103 |
| Деталь: | Tension roller bracket |
| Парткод: | G081 2133 |
| Деталь: | Hopper Change Gear |
| Парткод: | G081 2135 |
| Деталь: | Joint Gear |
| Парткод: | G081 2136 |
| Деталь: | Hopper Gear A |
| Парткод: | G081 2137 |
| Деталь: | Hopper Gear B |
| Парткод: | G081 2138 |
| Деталь: | Hopper Gear C |
| Парткод: | G081 2139 |
| Деталь: | Tension Roller Spring |
| Парткод: | G081 2141 |
| Деталь: | Shaft - Toner Cartidge Drive |
| Парткод: | G081 2142 |
| Деталь: | Base - Toner Cartridge Drive |
| Парткод: | G081 2201 |
| Деталь: | Sensor - Toner Empty |
| Парткод: | G081 5306 |
| Деталь: | Gear - Toner Cartridge Drive |
| Парткод: | G081 2202 |
| Деталь: | Gear - Toner Cartridge Drive |
| Парткод: | G081 2203 |
| Деталь: | Granding Plate |
| Парткод: | G081 2204 |
| Деталь: | E-ring |
| Парткод: | G081 4528 |
| Деталь: | WASHER |
| Парткод: | G081 4552 |
| Деталь: | Pickup Roller Holder |
| Парткод: | G081 2452 |
| Деталь: | Pickup Rubber |
| Парткод: | G081 2453 |
| Деталь: | One Way Clutch |
| Парткод: | G081 2481 |
| Деталь: | pickup roller |
| Парткод: | G081 2454 |
| Деталь: | Belt - Pickup Roller |
| Парткод: | G081 2455 |
| Деталь: | Paper Guide - Upper Cassette |
| Парткод: | G081 2456 |
| Деталь: | Separation Pad Holder |
| Парткод: | G081 2457 |
| Деталь: | Pickup Roller Shaft |
| Парткод: | G081 2458 |
| Деталь: | Right Paper Guide |
| Парткод: | G081 2460 |
| Деталь: | Left Paper Guide |
| Парткод: | G081 2459 |
| Деталь: | Paper Holder |
| Парткод: | G120 2402 |
| Деталь: | Paper Holder Spring |
| Парткод: | G081 2462 |
| Деталь: | PINION GEAR |
| Парткод: | G081 2463 |
| Деталь: | Cover - Main Cassette |
| Парткод: | G081 2464 |
| Деталь: | PAPER TRAY |
| Парткод: | G081 2465 |
| Деталь: | Paper Tray Base |
| Парткод: | G081 2466 |
| Деталь: | Left Cam |
| Парткод: | G081 2467 |
| Деталь: | Actuator - Paper Empty Sensor |
| Парткод: | G081 2468 |
| Деталь: | Cassette Gear Bracket |
| Парткод: | G081 2469 |
| Деталь: | SPRING |
| Парткод: | G081 2470 |
| Деталь: | BUSHING |
| Парткод: | G081 2472 |
| Деталь: | Roller Gear |
| Парткод: | G081 2473 |
| Деталь: | SEPARATION PAD |
| Парткод: | G120 2403 |
| Деталь: | SEPARATION PAD SPRING |
| Парткод: | G081 2475 |
| Деталь: | Tray Protector |
| Парткод: | G081 2476 |
| Деталь: | Idle Gear |
| Парткод: | G081 2477 |
| Деталь: | GEAR SPACER |
| Парткод: | G081 2478 |
| Деталь: | GEAR COVER |
| Парткод: | G081 2479 |
| Деталь: | Cam Gear |
| Парткод: | G081 2480 |
| Деталь: | Roller Position Arm |
| Парткод: | G081 2482 |
| Деталь: | CAM SHAFT |
| Парткод: | G081 2483 |
| Деталь: | Right Cam |
| Парткод: | G081 2484 |
| Деталь: | Screw 3x6 |
| Парткод: | G081 4522 |
| Деталь: | Screw 3x10 |
| Парткод: | G081 4517 |
| Деталь: | Friction pad |
| Парткод: | G081 2485 |
| Деталь: | E-ring |
| Парткод: | G081 4538 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | G081 2292 |
| Деталь: | Paper Guide Support |
| Парткод: | G081 2490 |
| Деталь: | Paper Tray Assy |
| Парткод: | G081 2494 |
| Деталь: | Decal - Paper Tray |
| Парткод: | G081 2495 |
| Деталь: | Access Panel |
| Парткод: | G081 2030 |
| Деталь: | Engine Board Shield Cover |
| Парткод: | G081 2033 |
| Деталь: | Engine Control Board G120/G123 |
| Парткод: | G120 5101 |
| Деталь: | Engine Control Board G121/G122 |
| Парткод: | G121 5101 |
| Деталь: | Engine Board Large Bracket |
| Парткод: | G081 2032 |
| Деталь: | Engine Board Small Bracket |
| Парткод: | G081 2013 |
| Деталь: | Fan Motor - DC24V-2.88W |
| Парткод: | G081 5210 |
| Деталь: | Fan Motor Duct |
| Парткод: | G081 2014 |
| Деталь: | GROUNDING PLATE |
| Парткод: | G081 2015 |
| Деталь: | Sensor - Temp.-humidity |
| Парткод: | G081 5301 |
| Деталь: | PLATE |
| Парткод: | G081 2016 |
| Деталь: | Motor - DC24V-8.16W |
| Парткод: | G081 5211 |
| Деталь: | Bracket - Paper Pickup Motor |
| Парткод: | G081 2017 |
| Деталь: | Paper Pickup Gear |
| Парткод: | G081 2018 |
| Деталь: | Duplex Unit Gear |
| Парткод: | G081 2020 |
| Деталь: | Inner cover |
| Парткод: | G081 2021 |
| Деталь: | Paper Size Detector |
| Парткод: | G081 5302 |
| Деталь: | Transfer Terminal |
| Парткод: | G081 2022 |
| Деталь: | Granding Plate - Fusing Unit |
| Парткод: | G081 2029 |
| Деталь: | Sensor - Duplex Unit Jam |
| Парткод: | G081 5303 |
| Деталь: | Sensor - Duplex Unit |
| Парткод: | G081 5304 |
| Деталь: | Toner Cartridge Holder |
| Парткод: | G120 2001 |
| Деталь: | Screw 3x6 |
| Парткод: | G081 4531 |
| Деталь: | Screw 3x6 |
| Парткод: | G081 4522 |
| Деталь: | Screw 3x35 |
| Парткод: | G081 4521 |
| Деталь: | Screw 3x12 |
| Парткод: | G081 4519 |
| Деталь: | Screw 3x10 |
| Парткод: | G081 4517 |
| Деталь: | Screw 3x8 |
| Парткод: | G081 4524 |
| Деталь: | GROUNDING PLATE |
| Парткод: | G081 2025 |
| Деталь: | Exit Fg Harness |
| Парткод: | G081 2026 |
| Деталь: | Sub Fusing Fan Dct |
| Парткод: | G081 2028 |
| Деталь: | Sub Fusing Fan |
| Парткод: | G081 5318 |
| Деталь: | Fusing Fan Duct |
| Парткод: | G081 2041 |
| Деталь: | Granding Plate - Laser Unit |
| Парткод: | G081 2382 |
| Деталь: | LASER UNIT |
| Парткод: | G081 2383 |
| Деталь: | Sensor Protector |
| Парткод: | G081 2384 |
| Деталь: | IH Shield Cover |
| Парткод: | G081 2385 |
| Деталь: | IH Assembly - 120V |
| Парткод: | G081 2386 |
| Деталь: | IH Assembly - 230V |
| Парткод: | G081 2392 |
| Деталь: | Fusing Unit Lock Lever |
| Парткод: | G081 2387 |
| Деталь: | IH Harness Cover |
| Парткод: | G081 2388 |
| Деталь: | CASSETTE STOPPER |
| Парткод: | G081 2389 |
| Деталь: | Cassette Stopper Roller |
| Парткод: | G081 2371 |
| Деталь: | Sensor - Paper Detection - MPT |
| Парткод: | G081 5311 |
| Деталь: | Sensor - Home Position - MPT |
| Парткод: | G081 5312 |
| Деталь: | Senser Cover |
| Парткод: | G081 2372 |
| Деталь: | Regist Stopper R |
| Парткод: | G120 2406 |
| Деталь: | Screw 3x6 |
| Парткод: | G081 4522 |
| Деталь: | Screw 3x12 |
| Парткод: | G081 4519 |
| Деталь: | WASHER |
| Парткод: | G081 4550 |
| Деталь: | Screw 3x10 |
| Парткод: | G081 4517 |
| Деталь: | PCU SUB Guide |
| Парткод: | G081 2373 |
| Деталь: | PAPER FEED UNIT |
| Парткод: | G120 2404 |
| Деталь: | Regist Stopper L |
| Парткод: | G120 2405 |
| Деталь: | Clutch - Dc24v-3w |
| Парткод: | G081 5325 |
| Деталь: | Registration Roller Joint Gear |
| Парткод: | G081 2401 |
| Деталь: | Pickup gear |
| Парткод: | G081 2471 |
| Деталь: | Inner Gear |
| Парткод: | G081 2403 |
| Деталь: | Outer Gear |
| Парткод: | G081 2404 |
| Деталь: | Inner Gear - B |
| Парткод: | G081 2405 |
| Деталь: | BUSHING |
| Парткод: | G081 2255 |
| Деталь: | GEAR |
| Парткод: | G081 2407 |
| Деталь: | Idle Gear |
| Парткод: | G081 2408 |
| Деталь: | Feed Gear |
| Парткод: | G081 2409 |
| Деталь: | Ratchet Arm |
| Парткод: | G081 2410 |
| Деталь: | GEAR BRACKET |
| Парткод: | G081 2411 |
| Деталь: | Solenoid - DC24V-4.8W |
| Парткод: | G081 5326 |
| Деталь: | Actuator - Paper Empty Sensor |
| Парткод: | G081 2499 |
| Деталь: | Sensor - Paper Resist/Empty |
| Парткод: | G081 5315 |
| Деталь: | Actuator - Paper Resistration |
| Парткод: | G081 2413 |
| Деталь: | SPRING |
| Парткод: | G081 2414 |
| Деталь: | BUSHING |
| Парткод: | G081 2415 |
| Деталь: | Spring - R |
| Парткод: | G081 2492 |
| Деталь: | Registration Roller Tension |
| Парткод: | G081 2417 |
| Деталь: | Registration Pinch Roller |
| Парткод: | G081 2418 |
| Деталь: | Registration Pinch Roller Gear |
| Парткод: | G081 2419 |
| Деталь: | PIN |
| Парткод: | G081 2420 |
| Деталь: | Registration Roller Gear |
| Парткод: | G081 2421 |
| Деталь: | Registration Roller |
| Парткод: | G120 2401 |
| Деталь: | Registration Paper Guide |
| Парткод: | G081 2423 |
| Деталь: | PINCH ROLLER |
| Парткод: | G081 2424 |
| Деталь: | PINCH ROLLER SPRING |
| Парткод: | G081 2496 |
| Деталь: | Pinch Roller Holder |
| Парткод: | G081 2426 |
| Деталь: | Paper Guide Spring |
| Парткод: | G081 2450 |
| Деталь: | Pinch Roller Shaft |
| Парткод: | G081 2427 |
| Деталь: | Pickup Rubber Frame |
| Парткод: | G081 2428 |
| Деталь: | Pickup Rubber |
| Парткод: | G081 2429 |
| Деталь: | Pickup Roller Shaft |
| Парткод: | G081 2430 |
| Деталь: | PIN |
| Парткод: | G081 2431 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | G081 2432 |
| Деталь: | BUSHING |
| Парткод: | G081 2433 |
| Деталь: | Plastic Washer |
| Парткод: | G081 2434 |
| Деталь: | Screw 3x6 |
| Парткод: | G081 4522 |
| Деталь: | Paper Feed Unit Frame |
| Парткод: | G081 2435 |
| Деталь: | BUSHING |
| Парткод: | G081 2472 |
| Деталь: | VARISTOR |
| Парткод: | G081 5330 |
| Деталь: | Snap Ring - D4 |
| Парткод: | G081 2489 |
| Деталь: | Spring - L |
| Парткод: | G081 2493 |
| Деталь: | Fan Motor - DC24V-2.88W |
| Парткод: | G081 5210 |
| Деталь: | Sensor - Toner Cartridge Cover |
| Парткод: | G081 5307 |
| Деталь: | Interlock Switch Bracket |
| Парткод: | G081 2211 |
| Деталь: | INTERLOCK SWITCH |
| Парткод: | G081 5316 |
| Деталь: | Fixing Plate - Transfer Belt |
| Парткод: | G081 2212 |
| Деталь: | Left Holer - Wase Toner Cartridge |
| Парткод: | G081 2213 |
| Деталь: | Interlock Lever |
| Парткод: | G081 2214 |
| Деталь: | Interlock Lever Spring |
| Парткод: | G081 2231 |
| Деталь: | IH Harnes Cover |
| Парткод: | G081 2215 |
| Деталь: | Interlock Cover |
| Парткод: | G081 2216 |
| Деталь: | Protect Cover |
| Парткод: | G081 2217 |
| Деталь: | Right Cover Plastic Strap |
| Парткод: | G081 2218 |
| Деталь: | Sensor - Waste Toner Full |
| Парткод: | G081 5308 |
| Деталь: | Blind Plate |
| Парткод: | G081 2219 |
| Деталь: | Right Holder - Waste Toner |
| Парткод: | G081 2220 |
| Деталь: | PCU Guide |
| Парткод: | G120 2201 |
| Деталь: | Transfer Belt Tension Unit |
| Парткод: | G081 2290 |
| Деталь: | Screw 3x35 |
| Парткод: | G081 4521 |
| Деталь: | Screw 3x12 |
| Парткод: | G081 4519 |
| Деталь: | Screw 3x8 |
| Парткод: | G081 4524 |
| Деталь: | INTERLOCK SWITCH |
| Парткод: | G081 5309 |
| Деталь: | Screw 2.2x16 |
| Парткод: | G081 4513 |
| Деталь: | Screw 3x8 |
| Парткод: | G081 4525 |
| Деталь: | Fusing Fan Connector Sheet |
| Парткод: | G081 2233 |
| Деталь: | PC Holder Unit |
| Парткод: | G081 2232 |
| Деталь: | Harness - CN1/CN2/CN3 |
| Парткод: | G081 5401 |
| Деталь: | Harness - CN45 |
| Парткод: | G081 5432 |
| Деталь: | Engine EEPROM |
| Парткод: | G120 5102 |
| Деталь: | Harness - CN11 |
| Парткод: | G081 5404 |
| Деталь: | Harness - CN7 |
| Парткод: | G081 5405 |
| Деталь: | Harness - CN9 |
| Парткод: | G081 5406 |
| Деталь: | Harness - CN10 |
| Парткод: | G081 5407 |
| Деталь: | Harness - CN30 |
| Парткод: | G081 5408 |
| Деталь: | Harness - CN12 |
| Парткод: | G081 5409 |
| Деталь: | Harness - CN17 |
| Парткод: | G081 5410 |
| Деталь: | Harness - CN15 |
| Парткод: | G081 5411 |
| Деталь: | Harness - CN39 |
| Парткод: | G081 5412 |
| Деталь: | Harness - CN33 |
| Парткод: | G081 5413 |
| Деталь: | Harness - CN35 |
| Парткод: | G081 5414 |
| Деталь: | Harness - CN34 |
| Парткод: | G081 5415 |
| Деталь: | Harness - CN8 |
| Парткод: | G081 5416 |
| Деталь: | Harness - CN13 |
| Парткод: | G081 5417 |
| Деталь: | Harness - CN14 |
| Парткод: | G081 5418 |
| Деталь: | Harness - CN18 |
| Парткод: | G081 5419 |
| Деталь: | Harness - CN23 |
| Парткод: | G081 5420 |
| Деталь: | Harness - CN29 |
| Парткод: | G081 5421 |
| Деталь: | Harness - CN5 |
| Парткод: | G081 5423 |
| Деталь: | Harness - CN27 |
| Парткод: | G081 5424 |
| Деталь: | Harness - CN28 |
| Парткод: | G081 5425 |
| Деталь: | Harness - CN32 |
| Парткод: | G081 5426 |
| Деталь: | FERRITE CORE |
| Парткод: | G081 5202 |
| Деталь: | FERRITE CORE |
| Парткод: | G081 5203 |
| Деталь: | FERRITE CORE |
| Парткод: | G081 5204 |
| Деталь: | FERRITE CORE |
| Парткод: | G081 5205 |
| Деталь: | FERRITE CORE |
| Парткод: | G081 5206 |
| Деталь: | Drive Cam - Waste Toner Cartridge |
| Парткод: | G081 2251 |
| Деталь: | Gear - Waste Toner Cartridge |
| Парткод: | G081 2252 |
| Деталь: | Planetary Gear - Waste Toner |
| Парткод: | G081 2253 |
| Деталь: | Planetary Gear Base |
| Парткод: | G081 2254 |
| Деталь: | BUSHING |
| Парткод: | G081 2255 |
| Деталь: | Cam Clutch Core |
| Парткод: | G081 2256 |
| Деталь: | CLUTCH SPRING |
| Парткод: | G081 2289 |
| Деталь: | Cam Clutch Slider |
| Парткод: | G081 2257 |
| Деталь: | Planetary Gear Base |
| Парткод: | G081 2258 |
| Деталь: | Planetary Gear |
| Парткод: | G081 2259 |
| Деталь: | Outer Gear |
| Парткод: | G081 2260 |
| Деталь: | Double Teeth Gear |
| Парткод: | G081 2261 |
| Деталь: | Cam Shaft Bushing |
| Парткод: | G081 2262 |
| Деталь: | Plastic Washer |
| Парткод: | G081 2263 |
| Деталь: | Cam Solenoid Spring |
| Парткод: | G081 2264 |
| Деталь: | Cam Ratchet |
| Парткод: | G081 2265 |
| Деталь: | Solenoid - DC24V-15W |
| Парткод: | G081 5252 |
| Деталь: | Sensor - Transfer Belt Home |
| Парткод: | G081 5310 |
| Деталь: | Base - Transfer Belt Tension Unit |
| Парткод: | G081 2266 |
| Деталь: | Bracket - Transfer Belt Tension |
| Парткод: | G081 2267 |
| Деталь: | Changer Lever Spring |
| Парткод: | G081 2268 |
| Деталь: | Changer Lever |
| Парткод: | G081 2269 |
| Деталь: | Solenoid - DC24V-15W |
| Парткод: | G081 5253 |
| Деталь: | Left Tension Cam Link |
| Парткод: | G081 2270 |
| Деталь: | Left Transfer Roller Cam |
| Парткод: | G081 2271 |
| Деталь: | Left Transfer Roller Cam Link |
| Парткод: | G081 2272 |
| Деталь: | BUSHING |
| Парткод: | G081 2273 |
| Деталь: | PLATE |
| Парткод: | G081 2274 |
| Деталь: | Left 1st Transfer Roller Cam Link |
| Парткод: | G081 2275 |
| Деталь: | Left 1st Transfer Roller Cam |
| Парткод: | G081 2276 |
| Деталь: | Damper Cam Link Assembly |
| Парткод: | G081 2277 |
| Деталь: | Home Tab |
| Парткод: | G081 2278 |
| Деталь: | TENSION SPRING |
| Парткод: | G081 2279 |
| Деталь: | Spring Support |
| Парткод: | G081 2280 |
| Деталь: | Sub Shaft |
| Парткод: | G081 2281 |
| Деталь: | PIN |
| Парткод: | G081 2282 |
| Деталь: | CAM SHAFT |
| Парткод: | G081 2283 |
| Деталь: | Right 1st Transfer Roller Cam |
| Парткод: | G081 2284 |
| Деталь: | Right 1st Transfer Roller Cam Link |
| Парткод: | G081 2285 |
| Деталь: | Right Transfer Roller Cam Link |
| Парткод: | G081 2286 |
| Деталь: | Right Transfer Roller Cam |
| Парткод: | G081 2287 |
| Деталь: | E-ring |
| Парткод: | G081 4528 |
| Деталь: | E-ring |
| Парткод: | G081 4529 |
| Деталь: | Right Tension Cam Link |
| Парткод: | G081 2288 |
| Деталь: | Cam Ratchet Bracket |
| Парткод: | G081 2374 |
| Деталь: | Plastic Washer |
| Парткод: | G081 2391 |
| Деталь: | Transfer Belt Tension Unit |
| Парткод: | G081 2290 |
| Деталь: | Main Stay Support Plate |
| Парткод: | G081 2291 |
| Деталь: | Screw 3x8 |
| Парткод: | G081 4525 |
| Деталь: | Bias Terminal Assembly |
| Парткод: | G081 2205 |
| Деталь: | Middle Terminal Spring |
| Парткод: | G081 2206 |
| Деталь: | Long Terminal Spring |
| Парткод: | G081 2207 |
| Деталь: | Short Terminal Spring |
| Парткод: | G081 2208 |
| Деталь: | Bias Terminal Plate A |
| Парткод: | G081 2209 |
| Деталь: | Bias Terminal Plate B |
| Парткод: | G081 2210 |
| Деталь: | Screw 2.3x6 |
| Парткод: | G081 4514 |
| Деталь: | Charge Harness |
| Парткод: | G081 4533 |
| Деталь: | Harness - Charge Output Process |
| Парткод: | G081 4534 |
| Деталь: | Harness - Charge Output Ftr |
| Парткод: | G081 4535 |
| Деталь: | Harness - Interface |
| Парткод: | G081 5422 |
| Деталь: | LCD Panel Cover |
| Парткод: | G081 1208 |
| Деталь: | STOPPER GUIDE |
| Парткод: | G081 1223 |
| Деталь: | Operation Panel - NA |
| Парткод: | G081 1940 |
| Деталь: | Rear Cover G120-17 |
| Парткод: | G120 1200 |
| Деталь: | Rear Cover G120-27 |
| Парткод: | G120 1201 |
| Деталь: | Rear Cover G120-22 |
| Парткод: | G120 1202 |
| Деталь: | Rear Cover G121-17 |
| Парткод: | G121 1200 |
| Деталь: | Rear Cover G121-27 |
| Парткод: | G121 1201 |
| Деталь: | Rear Cover G121-22 |
| Парткод: | G121 1202 |
| Деталь: | Rear Cover G121-69 |
| Парткод: | G121 1203 |
| Деталь: | Rear Cover G122-17 |
| Парткод: | G122 1200 |
| Деталь: | Rear Cover G123-27 |
| Парткод: | G123 1201 |
| Деталь: | Rear Cover G123-22 |
| Парткод: | G123 1202 |
| Деталь: | TOP COVER |
| Парткод: | G081 1204 |
| Деталь: | Cover - Option Paper Unit Harness |
| Парткод: | G081 1206 |
| Деталь: | CASSETTE COVER |
| Парткод: | G081 1207 |
| Деталь: | Left Axis - Front Cover |
| Парткод: | G081 1211 |
| Деталь: | Front Support Lever |
| Парткод: | G081 1212 |
| Деталь: | Right - Axis - Front Cover |
| Парткод: | G081 1213 |
| Деталь: | LEVER SPRING |
| Парткод: | G081 1214 |
| Деталь: | Toner Cartridge Cover |
| Парткод: | G081 1215 |
| Деталь: | LEFT COVER |
| Парткод: | G081 1202 |
| Деталь: | RIGHT COVER |
| Парткод: | G081 1203 |
| Деталь: | Sensor - Toner Cartridge Cover |
| Парткод: | G081 5307 |
| Деталь: | Cartridge Lever B |
| Парткод: | G081 1217 |
| Деталь: | Cartridge Lever A |
| Парткод: | G081 1218 |
| Деталь: | Right Cover Hook |
| Парткод: | G081 1219 |
| Деталь: | Screw - 3x8 |
| Парткод: | G081 4536 |
| Деталь: | Screw - 3x12 |
| Парткод: | G081 4519 |
| Деталь: | Screw - 3x12 |
| Парткод: | G081 4537 |
| Деталь: | STOPPER BASE |
| Парткод: | G081 1222 |
| Деталь: | FERRITE CORE |
| Парткод: | G081 5206 |
| Деталь: | Support Tray (NA) |
| Парткод: | G081 1226 |
Коды ошибок
201
230
302
440
441
471
486
487
530
531
532
543
544
554
580
581
622
640
641
670
680
818
819
820
821
822
823
824
827
828
829
835
836
837
850
851
853
854
855
856
857
860
861
863
864
865
900
990
991
998
999
Описание
| Error code: | 201 |
| Display: | ERROR 201 COMMAND |
| Description: | PU F/W Flash write error (Reserved) |
| Causes: | • Defective polygon motor • Defective harness |
| Remedy: | 1. Connect the cable correctly. 2. Replace the engine control board. 3. Replace the laser scanning unit. 4. Check or replace the cable. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 440 |
| Description: | Transfer Output Error. A high voltage feedback voltage of less than 0.5 V was detected for 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 441 |
| Description: | Image transfer unit motor error When the motor is ON, the machine monitors the lock signals every 100 ms. If the High status occurs 20 times consecutively, the machine judges that the motor is not rotating correctly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Shorted 24 V fuse on the PSU. Defective interlock systeme PSU. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system |
| Error code: | 471 |
| Description: | ITB skew adjustment error: time out The machine cannot complete the ITB centering control for 120 seconds after the ITB motor has started rotating. |
| Causes: | • Belt centering roller out of home position • ITB motor rotation sensor defective • Belt centering roller sensor defective • Belt centering roller motor defective |
| Remedy: | 1. Execute "Clearing SC471/475/476". 2. Replace the ITB motor rotation sensor. 3. Replace the belt centering roller sensor. 4. Replace the belt centering roller motor. |
| Error code: | 486 |
| Description: | Waste toner transport motor 2: Lock error The machine detects an error of the waste toner transport motor 2 while it is rotating. |
| Causes: | • Harness loose or disconnected • Blocking in the toner collection tube to the waste toner bottle. • Waste toner transport motor 2 defective |
| Remedy: | 1. Check the harness connection. 2. Replace the waste toner transport motor 2. |
| Error code: | 487 |
| Description: | Solenoid error Any of the following solenoids has caused a short circuit: changer solenoid, paper feed solenoid, toner supply solenoid. |
| Causes: | • Solenoid drive transistor short-circuited |
| Remedy: | 1. Replace the engine controller board. 2. Replace the defective solenoid. |
| Error code: | 530 |
| Description: | LSU Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the LSU fan motor. |
| Error code: | 531 |
| Description: | Fusing Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the fusing fan motor. |
| Error code: | 532 |
| Description: | IH coil fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH coil fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH coil fan motor • Defective IH coil fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH coil fan. 3. Replace the IOB. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 554 |
| Description: | Fusing sleeve belt overheat: End (hardware error) The fusing sleeve belt thermistor detects 250°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 580 |
| Description: | IH inverter zero cross frequency error The zero cross signal is not detected for 1 second or more after the IH inverter has turned on. |
| Causes: | • Disconnected CN983 on the IH inverter • Defective IH inverter • Defective IH coil unit |
| Remedy: | 1. Check CN983 on the IH inverter. 2. Replace the IH inverter. 3. Replace the IH coil unit. |
| Error code: | 581 |
| Description: | NC sensor broken: Center The sensor detects -17°C or less for 6 seconds |
| Causes: | Defective thermopile. Defective thermistor. Loose connection. |
| Error code: | 622 |
| Description: | Paper Bank communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The paper bank`s control board is faulty. Defective BCU/IOB. The paper bank`s connection is faulty. |
| Remedy: | • Reconnect the paper bank cables. • Replace the BCU. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 640 |
| Description: | Communication error: Engine Controller (Check sum error) Sum value is added each command frame. Sum check means: STX xx xx xx xx sum ETX -> The least significant 7 bits of xx + xx + xx+ xx is compared with the sum Example: STX 80h 81h 82h 83h 06h ETX -> 80h + 81h + 82h + 83h = 206h If sum value is 06h, data is correct. This SC is not displayed when it occurs; count is executed only by logging. |
| Causes: | Hard error with PCI |
| Remedy: | 1. Turn the main switch off and on. |
| Error code: | 641 |
| Description: | BICU control data transfer abnormal A sampling of the control data sent from the BICU reveals an abnormality. |
| Causes: | • Defective controller board • External noise • Defective BCU |
| Remedy: | 1. Replace the controller board. 2. Replace the BCU. |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 680 |
| Description: | BCU error |
| Causes: | • Defective BCU |
| Remedy: | 1. Replace the EEPROM. 2. Replace the engine control board. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 835 |
| Display: | SYSTEM HALT (*) 835 : FW/PRN MDL |
| Description: | Self-diagnostic error: Centronic device |
| Causes: | [1102] Loopback connector is connected but check results in an error. • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [110C] Loopback connector is connected but check results in an error. • ASIC device error • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [1120] Centronic loopback connector is not connected for detailed self-diagnostic test. • Centronic loopback connector not connected correctly • Centronic loopback connector defective • ASIC device defective Replace the controller board. |
| Error code: | 836 |
| Display: | SYSTEM HALT (*) 836 : FW/SV MDL |
| Description: | Self-diagnostics error: Font ROM (standard) |
| Causes: | Turn the main switch off and on. Replace the standard ROM-DIMM. |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the controller board. |
| Error code: | 837 |
| Display: | SYSTEM HALT (*) 837 : FW/PRN MDL |
| Description: | Self-diagnostic error - Optional font ROM The data in the font ROM (optional ROM-DIMM) is damaged. |
| Causes: | • Defective optional ROM-DIMM. |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the optional ROM-DIMM. |
| Error code: | 850 |
| Description: | Net I/F error Duplicate IP addresses. Illegal IP address. Driver unstable and cannot be used on the network |
| Causes: | • IP address setting incorrect • NIB (PHY) board defective • Controller board defective |
| Remedy: | Turn the main switch off and on. |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
| Error code: | 999 |
| Display: | Service call 999: Error |
| Description: | Stapler Motor Error |
| Causes: | • Color registration (MUSIC) failure |
| Remedy: | 1 Are staples jammed in the stapler? Go to step 2. Go to step 3. 2 Clear the staple jam and run the staple test in diagnostic mode or run a staple job. Does the problem reoccur? Replace the staple cartridge and to go step 4. Problem solved. 3 Are the connectors CN5 on the stapler and PJ1 on the finisher control board securely connected? Go to step 5. Securely connect the connectors. 4 Did replacement of the stapler cartridge resolve the problem? Problem resolved. Replace the stapler. 5 Make sure the finisher set switch is activated. Measure for 5 V dc between pins 11 and 12 on stapler connector CN5. Is 5 V dc present? Replace the stapler. Replace the finisher control board. 6 Did replacement of the finisher control board correct the problem? Problem solved. Go to step 7. 7 Is there continuity on the stapler to finisher control board cable? Replace the power supply. Replace the cable. |
Название
RICOH TYPE 125 Тонер-картридж черный
RICOH TYPE 125 Тонер-картридж голубой
RICOH TYPE 125 Тонер-картридж пурпурный
RICOH TYPE 125 Тонер-картридж желтый
(400842) RICOH TYPE 125 Блок фотобарабана черный
(400843) RICOH TYPE 125 Блок цветных фотобарабанов
RICOH TYPE 125 Узел переноса
