Ricoh FX150SF
Рейтинг
Модули
ADF Unit 1
PAPER CASSETTE
EXTERIOR 1
ADF UNIT 2
FUSING UNIT
OPTICS SECTION 1
EXTERIOR 2
Exterior 4
Exterior 5
OPTICS SECTION 2
LD & Electrical
Paper Regist
FRAME SECTION
EXTERIOR 3
Детали EXTERIOR 1
| Деталь: | Cover:ADF |
| Парткод: | M048 1054 |
| Деталь: | ADF Motor Cover |
| Парткод: | M048 1055 |
| Деталь: | ADF Exit Tray |
| Парткод: | M048 1056 |
| Деталь: | Screw:M3x8 |
| Парткод: | M048 1058 |
| Деталь: | Cover Hinge ADF |
| Парткод: | M048 1086 |
| Деталь: | Paper Tray:Front:Assy |
| Парткод: | G127 2595 |
| Деталь: | Side Fence - Left |
| Парткод: | G127 2614 |
| Деталь: | Tray Bottom Plate Assy |
| Парткод: | G127 2611 |
| Деталь: | Compression Spring - Bottom Plate |
| Парткод: | G127 2613 |
| Деталь: | Side Fence - Right |
| Парткод: | G127 2615 |
| Деталь: | END FENCE |
| Парткод: | G127 2617 |
| Деталь: | Paper Tray - Rear |
| Парткод: | G127 2616 |
| Деталь: | SIDE FENCE GEAR |
| Парткод: | G800 3133 |
| Деталь: | Friction pad |
| Парткод: | G127 2623 |
| Деталь: | PRESSURE SPRING |
| Парткод: | B044 2717 |
| Деталь: | STOPPER |
| Парткод: | B044 2713 |
| Деталь: | Spring - Release Lever |
| Парткод: | G020 2599 |
| Деталь: | Paper Tray:Front |
| Парткод: | G127 2618 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | G182 2638 |
| Деталь: | Opeartion Panel:EU (M048) |
| Парткод: | M048 3001 |
| Деталь: | Operation Panel:CHN (M048) |
| Парткод: | M048 1001 |
| Деталь: | Operation Panel:AA (M048) |
| Парткод: | M048 2001 |
| Деталь: | Operation Panel:EU (M049) |
| Парткод: | M049 3001 |
| Деталь: | Operation Panel:CHN (M049) |
| Парткод: | M049 1001 |
| Деталь: | Operation Panel:AA (M049) |
| Парткод: | M049 2001 |
| Деталь: | ADF Left Guide |
| Парткод: | M048 1060 |
| Деталь: | ADF Right Guide |
| Парткод: | M048 1061 |
| Деталь: | Bearing:Roller |
| Парткод: | M048 1062 |
| Деталь: | Screw:M3x8 |
| Парткод: | M048 1058 |
| Деталь: | Upper Paper Guide |
| Парткод: | M048 1064 |
| Деталь: | Cork Pad |
| Парткод: | M048 1065 |
| Деталь: | Paper Input Guide |
| Парткод: | M048 1066 |
| Деталь: | Scan Pass Guide |
| Парткод: | M048 1067 |
| Деталь: | Scan Pass Guide |
| Парткод: | M048 1068 |
| Деталь: | Antistatic Blade |
| Парткод: | M048 1069 |
| Деталь: | Brush Ground Plate |
| Парткод: | M048 1070 |
| Деталь: | Tray Gear |
| Парткод: | M048 1071 |
| Деталь: | ADF Feeder |
| Парткод: | M048 1072 |
| Деталь: | BEARING |
| Парткод: | M048 1073 |
| Деталь: | Analysis Roller |
| Парткод: | M048 1074 |
| Деталь: | Gear:38z |
| Парткод: | M048 1075 |
| Деталь: | Gear:27Z/33Z |
| Парткод: | M048 1076 |
| Деталь: | ADF MOTOR |
| Парткод: | M048 1077 |
| Деталь: | Gear:16Z/51Z |
| Парткод: | M048 1078 |
| Деталь: | Gear:42z |
| Парткод: | M048 1079 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | M048 1080 |
| Деталь: | PAPER FEED ROLLER ASSY |
| Парткод: | M048 1081 |
| Деталь: | Paper Deflect Guide |
| Парткод: | M048 1084 |
| Деталь: | Analysis Roller Deflect |
| Парткод: | M048 1082 |
| Деталь: | Fusing Unit:EU |
| Парткод: | G191 4210 |
| Деталь: | Bushing - Exit Roller |
| Парткод: | G127 4068 |
| Деталь: | EXIT ROLLER |
| Парткод: | G127 4451 |
| Деталь: | Gear - 17Z |
| Парткод: | G127 4463 |
| Деталь: | Gear - 22Z |
| Парткод: | G127 4082 |
| Деталь: | Left Holder - Exit Driven Roller |
| Парткод: | G052 4871 |
| Деталь: | Outer Exit Cover Roller |
| Парткод: | G052 4873 |
| Деталь: | Right Holder - Exit Driven Roller |
| Парткод: | G052 4872 |
| Деталь: | Fusing Thermistor |
| Парткод: | G052 5501 |
| Деталь: | Hot Roller Bushing - Left |
| Парткод: | G127 4291 |
| Деталь: | Gear - 22Z/26Z |
| Парткод: | G127 4298 |
| Деталь: | Harness:Paper Feed Sensor:5V |
| Парткод: | G191 5745 |
| Деталь: | Fusing Cover - Left |
| Парткод: | G127 4324 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | G127 4285 |
| Деталь: | Pressure Roller - DIA25 |
| Парткод: | G127 4297 |
| Деталь: | Pressure Roller Bushing |
| Парткод: | G127 4294 |
| Деталь: | Compression Spring - Pressure |
| Парткод: | G127 4295 |
| Деталь: | Pressure Ground Plate |
| Парткод: | G127 4290 |
| Деталь: | Gear - 17Z |
| Парткод: | G127 4281 |
| Деталь: | Exit Roller:Fusing |
| Парткод: | G191 4286 |
| Деталь: | Hot Roller Stripper |
| Парткод: | G052 4624 |
| Деталь: | Spring - Paper Feed Sensor Feeler |
| Парткод: | G127 4221 |
| Деталь: | Feeler - Paper Feed Sensor |
| Парткод: | G127 4288 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | GROUND PLATE |
| Парткод: | G127 4289 |
| Деталь: | External Circlip |
| Парткод: | G127 4465 |
| Деталь: | Gear:Hot Roller:DIA30 |
| Парткод: | G127 4312 |
| Деталь: | Heater - 600W |
| Парткод: | G127 4273 |
| Деталь: | Hot Roller Bushing - Right |
| Парткод: | G127 4292 |
| Деталь: | Heater Plate Nut |
| Парткод: | G127 4218 |
| Деталь: | Electrode - Left |
| Парткод: | G127 4317 |
| Деталь: | Electrode - Middle |
| Парткод: | G127 4296 |
| Деталь: | Thermostat - 175C |
| Парткод: | G127 4313 |
| Деталь: | Electrode - Right |
| Парткод: | G127 4321 |
| Деталь: | Hot Roller:DIA30 |
| Парткод: | G127 4079 |
| Деталь: | Harness - Heater/Power Supply Unit |
| Парткод: | G182 5723 |
| Деталь: | EXIT ROLLER |
| Парткод: | G127 4316 |
| Деталь: | Spring - Exit Roller |
| Парткод: | G127 4315 |
| Деталь: | Tension Spring - Pickoff Pawl |
| Парткод: | G127 4148 |
| Деталь: | Decal - High Temperature |
| Парткод: | G127 4329 |
| Деталь: | Harness:Thermistor:Fusing:5V |
| Парткод: | G191 5742 |
| Деталь: | Decal - High Temperature |
| Парткод: | G127 4328 |
| Деталь: | Pressure Roller - Entrance |
| Парткод: | G168 4465 |
| Деталь: | Screw:M3x10 |
| Парткод: | M048 1020 |
| Деталь: | Scanner Frame |
| Парткод: | M049 1028 |
| Деталь: | Scanner Frame |
| Парткод: | M048 1031 |
| Деталь: | CIS Spring |
| Парткод: | M048 1045 |
| Деталь: | Flat Cable:CIS |
| Парткод: | M048 1029 |
| Деталь: | Scanner Cable |
| Парткод: | M048 1032 |
| Деталь: | Drive Pulley:CIS |
| Парткод: | M048 1033 |
| Деталь: | Console Cord 16 pin |
| Парткод: | M048 1034 |
| Деталь: | Scanner base |
| Парткод: | M048 1035 |
| Деталь: | Gear:55Z |
| Парткод: | M048 1036 |
| Деталь: | CIS Drive-under Motor |
| Парткод: | M048 1037 |
| Деталь: | Gear:32Z/70Z |
| Парткод: | M048 1038 |
| Деталь: | CIS Drive Adapter |
| Парткод: | M048 1039 |
| Деталь: | Heat Sink:CIS Drive |
| Парткод: | M048 1040 |
| Деталь: | Scanner Motor |
| Парткод: | M048 1041 |
| Деталь: | Left Slider |
| Парткод: | M048 1042 |
| Деталь: | CIS:A4:600DPI |
| Парткод: | M048 1043 |
| Деталь: | RIGHT SLIDER |
| Парткод: | M048 1044 |
| Деталь: | Original Tray |
| Парткод: | M048 1006 |
| Деталь: | Screw 3x6 |
| Парткод: | M048 1008 |
| Деталь: | SPEAKER |
| Парткод: | M048 1009 |
| Деталь: | RIGHT COVER |
| Парткод: | M048 1010 |
| Деталь: | BRACKET |
| Парткод: | M048 1011 |
| Деталь: | Main Board:EU (M048) |
| Парткод: | M048 3003 |
| Деталь: | Main Board:AA (M048) |
| Парткод: | M048 2003 |
| Деталь: | Main Board:OC (M048) |
| Парткод: | M048 4003 |
| Деталь: | Main Board:CHN (M049) |
| Парткод: | M049 1011 |
| Деталь: | Main Board:EU (M049) |
| Парткод: | M049 3003 |
| Деталь: | Main Board:AA (M049) |
| Парткод: | M049 2003 |
| Деталь: | Main Board:CHN (M048) |
| Парткод: | M048 1012 |
| Деталь: | Front door |
| Парткод: | G182 1283 |
| Деталь: | LEFT COVER |
| Парткод: | M048 1014 |
| Деталь: | Operation Board:CHN (M048) |
| Парткод: | M048 1015 |
| Деталь: | Operation Board:EU (M048) |
| Парткод: | M048 3004 |
| Деталь: | Operation Board:AA (M048) |
| Парткод: | M048 2004 |
| Деталь: | Flat Bed Cover |
| Парткод: | M049 1004 |
| Деталь: | Operation Board:CHN (M049) |
| Парткод: | M049 1015 |
| Деталь: | Operation Board:EU (M049) |
| Парткод: | M049 3004 |
| Деталь: | Operation Board:AA (M049) |
| Парткод: | M049 2004 |
| Деталь: | Printer Exit Paper Guide |
| Парткод: | G127 4299 |
| Деталь: | Screw:M3x10 |
| Парткод: | M048 1020 |
| Деталь: | REAR COVER |
| Парткод: | M048 1021 |
| Деталь: | REAR COVER |
| Парткод: | M049 1018 |
| Деталь: | REAR COVER |
| Парткод: | G127 1217 |
| Деталь: | Extended Exit Try |
| Парткод: | G191 1212 |
| Деталь: | Middle Frame |
| Парткод: | M048 1024 |
| Деталь: | Screw:M3x6 |
| Парткод: | M048 1008 |
| Деталь: | Screw:M3x10 |
| Парткод: | M048 1020 |
| Деталь: | Discharge Brush:Exit |
| Парткод: | G127 1297 |
| Деталь: | Interface Cover |
| Парткод: | M048 1028 |
| Деталь: | Flat Cable:CIS |
| Парткод: | M048 1029 |
| Деталь: | Ferrite Flat Cable 16 PIN |
| Парткод: | M048 1085 |
| Деталь: | FLAT CABLE |
| Парткод: | M048 1046 |
| Деталь: | Flat Cable:CIS |
| Парткод: | M048 1029 |
| Деталь: | Central Roller |
| Парткод: | M048 1048 |
| Деталь: | CIS Support |
| Парткод: | M048 1049 |
| Деталь: | Lateral Roller |
| Парткод: | M048 1050 |
| Деталь: | Belt Connection |
| Парткод: | M048 1051 |
| Деталь: | Belt Spring |
| Парткод: | M048 1052 |
| Деталь: | Drive Belt:CIS |
| Парткод: | M048 1053 |
| Деталь: | Imaging Unit |
| Парткод: | G191 1850 |
| Деталь: | Laser Unit Cover |
| Парткод: | G127 1901 |
| Деталь: | Polygon Mirror Motor |
| Парткод: | G127 1953 |
| Деталь: | Laser Diode Shutter |
| Парткод: | G127 1923 |
| Деталь: | Spring - Shutter |
| Парткод: | G127 1922 |
| Деталь: | Harness - Micro Switch |
| Парткод: | G182 5740 |
| Деталь: | FAN DUCT |
| Парткод: | G127 1070 |
| Деталь: | Fan Motor MM80 |
| Парткод: | AX64 0159 |
| Деталь: | Fan Seal |
| Парткод: | G127 1077 |
| Деталь: | Harness - Heater |
| Парткод: | G127 5724 |
| Деталь: | Harness:Power Source:24V |
| Парткод: | G191 5736 |
| Деталь: | Harness:Polygon Mirror Motor:24V |
| Парткод: | G191 1954 |
| Деталь: | POWER SUPPLY UNIT |
| Парткод: | G191 5510 |
| Деталь: | Power Supply Unit:CHN |
| Парткод: | G191 5514 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Harness:AIO:5V |
| Парткод: | G191 5741 |
| Деталь: | Harness:Image Forming Section:5V |
| Парткод: | G191 5738 |
| Деталь: | Harness - Laser Unit |
| Парткод: | G127 5738 |
| Деталь: | Drive Case |
| Парткод: | G127 1169 |
| Деталь: | Spring - Drive |
| Парткод: | G127 1187 |
| Деталь: | Spacer - Drive Unit |
| Парткод: | G127 1140 |
| Деталь: | Gear - 125Z |
| Парткод: | G127 1182 |
| Деталь: | Gear - 20Z |
| Парткод: | G127 1181 |
| Деталь: | Spacer : 8 x 0.2 |
| Парткод: | G006 4917 |
| Деталь: | Discharge Brush - Exit Roller |
| Парткод: | G127 4136 |
| Деталь: | Brushless Motor - DC 14.2W |
| Парткод: | G191 1170 |
| Деталь: | Gear - 28Z |
| Парткод: | G025 3405 |
| Деталь: | Bushing - Transfer Roller |
| Парткод: | G025 3407 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | G127 6201 |
| Деталь: | Transfer Roller Bracket |
| Парткод: | G025 3403 |
| Деталь: | Spring - Transfer Roller |
| Парткод: | G025 3404 |
| Деталь: | THERMISTOR |
| Парткод: | G127 1088 |
| Деталь: | Shaft - Paper Pick-up Sensor |
| Парткод: | G025 3048 |
| Деталь: | Actuator - Paper Pick-up Sensor |
| Парткод: | G025 3047 |
| Деталь: | Spring - Paper Pick-up Sensor |
| Парткод: | G025 3049 |
| Деталь: | Guide Plate - Manual Feed |
| Парткод: | G127 2565 |
| Деталь: | Spring - Roller |
| Парткод: | G127 2563 |
| Деталь: | Bushing - Right |
| Парткод: | G127 2562 |
| Деталь: | Bushing - Drive |
| Парткод: | G127 2620 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | G127 2575 |
| Деталь: | Paper Feed Roller - MM32 |
| Парткод: | G127 2627 |
| Деталь: | Paper feed Shaft |
| Парткод: | G127 2570 |
| Деталь: | DRIVE ROLLER |
| Парткод: | G127 2553 |
| Деталь: | Gear - 17Z |
| Парткод: | G127 2582 |
| Деталь: | Roller - Driven |
| Парткод: | G127 2559 |
| Деталь: | Bushing - Left |
| Парткод: | G127 2561 |
| Деталь: | Bracket - Paper Feed Roller |
| Парткод: | G127 2576 |
| Деталь: | Magnetic Clutch - 43Z |
| Парткод: | G127 2583 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | G127 2581 |
| Деталь: | Harness:Sensor:5V |
| Парткод: | G191 5737 |
| Деталь: | Sensor bracket |
| Парткод: | G127 2580 |
| Деталь: | Gear - 20Z/124Z |
| Парткод: | G127 1185 |
| Деталь: | Gear - 20Z/130Z |
| Парткод: | G127 1184 |
| Деталь: | Harness:Mechanical Drive:24V |
| Парткод: | G191 5735 |
| Деталь: | Spacer - Paper Feed Roller |
| Парткод: | G127 2634 |
| Деталь: | Bracket:SAGEM2:AIO |
| Парткод: | G191 1035 |
| Деталь: | Process Magazine:Accessory:LONGFA2 |
| Парткод: | G191 0150 |
| Деталь: | Ground Wire:Bracket:Discharge Lamp |
| Парткод: | G191 5722 |
| Деталь: | Harness:Discharge Lamp:24V |
| Парткод: | G191 5721 |
| Деталь: | Paper Tray Rail - Left |
| Парткод: | G127 2586 |
| Деталь: | AIO Rail - Left |
| Парткод: | G127 1093 |
| Деталь: | AIO Rail - Right |
| Парткод: | G127 1084 |
| Деталь: | Paper feed Guide |
| Парткод: | G127 2556 |
| Деталь: | Paper Tray Rail - Right |
| Парткод: | G127 2588 |
| Деталь: | Feeler - Manual Feed Sensor |
| Парткод: | G127 1073 |
| Деталь: | Spring - Feeler |
| Парткод: | G127 1074 |
| Деталь: | Rubber Foot - GF |
| Парткод: | G027 1180 |
| Деталь: | Harness Case |
| Парткод: | G127 1086 |
| Деталь: | HARNESS COVER |
| Парткод: | G127 1087 |
| Деталь: | Positioning Lever - Left |
| Парткод: | G127 1057 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | G127 1061 |
| Деталь: | Bracket - Left Upper |
| Парткод: | G182 1034 |
| Деталь: | Positioning Lever - Right |
| Парткод: | G127 1060 |
Коды ошибок
01
03
04
05
06
07
08
0A
0B
0C
0D
13
14
16
19
1A
1B
Описание
| Error code: | 01 |
| Display: | ERROR CONDITION INVALID HEAD |
| Description: | The ERROR light flashes. |
| Causes: | The printhead was replaced with one that is not a genuine Zebra™ printhead. |
| Remedy: | Install a genuine Zebra printhead. |
| Error code: | 03 |
| Display: | WARNING RIBBON IN |
| Description: | The ERROR light flashes. |
| Causes: | Ribbon is loaded, but the printer is set for direct thermal mode. |
| Remedy: | Ribbon is not required with direct thermal media. If you are using direct thermal media, remove the ribbon. This error message will not affect printing. If you are using thermal transfer media, which requires ribbon, set the printer for Thermal Transfer mode. See Select Print Method on page 81. |
| Error code: | 04 |
| Display: | ERROR CONDITION PAPER OUT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded. |
| Remedy: | Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration. |
| Error code: | 05 |
| Display: | ERROR CONDITION HEAD OPEN |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The printhead is not fully closed. The head open sensor is not working properly. |
| Remedy: | Replace the sensor. |
| Error code: | 06 |
| Display: | THERMISTOR FAULT |
| Description: | The ERROR light flashes. |
| Causes: | The printhead has a faulty thermistor. |
| Remedy: | Replace the printhead. |
| Error code: | 07 |
| Display: | WARNING HEAD COLD, THERMISTOR FAULT, ERROR CONDITION HEAD ELEMENT BAD |
| Description: | The printer stops; the ERROR light is on; the printer cycles through these three messages. |
| Causes: | The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
| Remedy: | Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
| Error code: | 08 |
| Display: | WARNING HEAD COLD |
| Description: | The printer prints while the ERROR light flashes. |
| Causes: | The printhead temperature is approaching its lower operating limit. The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
| Remedy: | Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the printer to a warmer area. Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
| Error code: | 0A |
| Description: | No document to recover |
| Causes: | You have attempted to recover a document from a correspondent, but the latter has not stored the document or the password that was entered is wrong. |
| Remedy: | Contact your correspondent to check whether the document to recover has been stored or to check the validity of the password. |
| Error code: | 0B |
| Description: | Transfer Fan Malfunction |
| Causes: | Ventilation Fan Motor (M6) PWB-A (Engine Control Board) Power Unit (PU) |
| Remedy: | 1 Check the M6 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 Check the PWB-A connector for proper connection and correct as necessary. 4 M6 operation check. PWB-A PJ10A-1 (REM) PWB-A PJ10A-3 (LOCK) 2-H 5 Change PWB-A. 6 Change PU. |
| Error code: | 0C |
| Description: | Power Supply Cooling Fan Malfunction |
| Causes: | Power Supply Cooling Fan Motor (M4) PWB-A (Engine Control Board) Power Unit (PU) |
| Remedy: | 1 Check the M4 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 Check the PWB-A connector for proper connection and correct as necessary. 4 M4 operation check. PWB-A PJ4A-1 (REM) PWB-A PJ4A-3 (LOCK) 7-I 5 Change PWB-A. 6 Change PU. |
| Error code: | 0D |
| Display: | Paper Jam |
| Description: | Document transmission fault |
| Causes: | Document reception error. |
| Remedy: | Ask the correspondent to retransmit his document. |
| Error code: | 13 |
| Description: | Long tracks of missing print on several labels |
| Causes: | Print element damaged. |
| Remedy: | Replace the printhead. |
| Error code: | 14 |
| Description: | Wrinkled ribbon |
| Causes: | Ribbon fed through the machine incorrectly. Incorrect burn temperature. Incorrect or uneven printhead pressure. Media not feeding properly; walking from side to side. The strip plate needs adjusting. The printhead needs vertical adjustment. The printhead is improperly balanced. The printhead and platen roller need to be realigned. |
| Remedy: | See Load Ribbon on page 64. Set the darkness to the lowest possible setting for good print quality. See Adjust Print Darkness on page 78. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Make sure that media is snug by adjusting the media guide, or call a service technician. Adjust the printhead balance. |
| Error code: | 16 |
| Description: | Smudge marks on labels |
| Causes: | The media or ribbon is not designed for high-speed operation. |
| Remedy: | Replace supplies with those recommended for high-speed operation. |
| Error code: | 19 |
| Description: | Vertical drift in top-of-form position |
| Causes: | The printer is out of calibration. Vertical drift occurs during normal printer operation. Note • A vertical drift of ± 4 to 6 dot rows (approximately 0.5 mm) is within normal tolerances. The platen roller is dirty. |
| Remedy: | Recalibrate the printer. Calibrate the printer. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. |
| Error code: | 1A |
| Description: | Disconnect |
| Causes: | Transmission has not started (the phone line is too noisy). |
| Remedy: | Check the quality of the phone line or restart the transmission at a later time. |
| Error code: | 1B |
| Description: | Document transmission fault |
| Causes: | Document transmission error. |
| Remedy: | Transmission: restart the transmission. Reception: ask your correspondent to retransmit the document. |
