Ricoh MP161
Рейтинг
Модули
ARDF 3 (B292)
EXTENTION BOX (B262/B292/B280/B293)
FUSING UNIT (B262/B292/B280/B293)
OPTICS SECTION 1 (B262/B292/B280/B293)
PAPER CASSETTE (B262/B292/B280/B293)
ARDF 1 (B292)
PCU SECTION (B262/B292/B280/B293)
ARDF 4 (B292)
PAPER REGISTRATION (B262/B292/B280/B293)
ARDF 2 (B292)
EXTERIOR (B262/B292/B280/B293)
ELECTRICAL SECTION (B262/B292/B280/B293)
BY-PASS FEED UNIT (B262/B292/B280/B293)
TRANSPORT SECTION (B262/B292/B280/B293)
ARDF 5 (B292)
DRIVE SECTION (B262/B292/B280/B293)
LASER UNIT (B262/B292/B280/B293)
FRAME SECTION (B262/B292/B280/B293)
OPERATION PANEL (B262/B292/B280/B293)
OPTICS SECTION 2 (B262/B292/B280/B293)
Детали ARDF 4 (B292)
| Деталь: | Holder:Reverse Roller |
| Парткод: | B872 2222 |
| Деталь: | Reverse Roller |
| Парткод: | AF03 2030 |
| Деталь: | Bushing:R1 |
| Парткод: | B872 2614 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Shaft:Reverse Roller |
| Парткод: | B872 2221 |
| Деталь: | Gear:Z17 |
| Парткод: | B872 2223 |
| Деталь: | Shaft:Drive:Separation |
| Парткод: | B872 2213 |
| Деталь: | Compression Spring:Reverse:Driven |
| Парткод: | B872 2116 |
| Деталь: | Shaft:Reverse:Roller:Driven |
| Парткод: | B872 2113 |
| Деталь: | Roller:Driven:Dia14 |
| Парткод: | B872 2112 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA08 0034 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Guide Plate:Paper Feed:Lower |
| Парткод: | B872 2110 |
| Деталь: | Bracket:Reverse |
| Парткод: | B872 2211 |
| Деталь: | Spring Plate:Reverse:Pressure |
| Парткод: | B872 2212 |
| Деталь: | CUSHION |
| Парткод: | B044 4962 |
| Деталь: | Photointerruptor:Paper Size Sensor |
| Парткод: | AW02 |
| Деталь: | Gear:Z44/T14 |
| Парткод: | B872 4116 |
| Деталь: | Gear:Z44/T16 |
| Парткод: | B872 4113 |
| Деталь: | Timing Belt:B40S2M128 |
| Парткод: | AA04 3603 |
| Деталь: | Gear:Z22 |
| Парткод: | B872 2613 |
| Деталь: | Bracket:Motor:Paper Feed:Ass`y |
| Парткод: | B872 4111 |
| Деталь: | Stepper Motor DC24V 3.53W |
| Парткод: | B872 5810 |
| Деталь: | Stopper:Original Table |
| Парткод: | B872 1121 |
| Деталь: | Compression Spring:Stopper |
| Парткод: | B872 1122 |
| Деталь: | Torque Limiter:T24:S2M |
| Парткод: | B872 3232 |
| Деталь: | Roller:Reverse:Drive |
| Парткод: | B872 3231 |
| Деталь: | Roller:R0 |
| Парткод: | B872 2611 |
| Деталь: | Guide:Reverse |
| Парткод: | B872 2118 |
| Деталь: | Gear:Z28 |
| Парткод: | B872 2217 |
| Деталь: | Gear - 18/30Z |
| Парткод: | AB01 7591 |
| Деталь: | Gear:Z19 |
| Парткод: | B872 2612 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 8 053 480 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | PCB:NC4-S:GDI-Nob |
| Парткод: | B880 5171 |
| Деталь: | PCB:NC4-S:GDI-Basic |
| Парткод: | B880 5172 |
| Деталь: | GWCTL Shadeing Plate |
| Парткод: | B129 1306 |
| Деталь: | Bracket:PCB:GDI |
| Парткод: | B262 1300 |
| Деталь: | Cover:SD |
| Парткод: | B262 1254 |
| Деталь: | Interface Cover |
| Парткод: | B129 1309 |
| Деталь: | FCU Bracket |
| Парткод: | B129 1308 |
| Деталь: | Guide Plate Sponge |
| Парткод: | H547 4203 |
| Деталь: | Bracket:Lan |
| Парткод: | B262 1323 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Fusing Unit (120V) |
| Парткод: | B262 4018 |
| Деталь: | Fusing Unit (230V) |
| Парткод: | B262 4028 |
| Деталь: | Discharge Brush |
| Парткод: | B044 4165 |
| Деталь: | Spring Plate |
| Парткод: | B044 4166 |
| Деталь: | Feeler |
| Парткод: | B044 4183 |
| Деталь: | GUIDE PLATE |
| Парткод: | B044 4186 |
| Деталь: | SPRING |
| Парткод: | B044 4138 |
| Деталь: | Turn-roller |
| Парткод: | AF02 2141 |
| Деталь: | EXIT ROLLER |
| Парткод: | AF04 0603 |
| Деталь: | Middle Roller |
| Парткод: | AF02 2142 |
| Деталь: | EXIT ROLLER |
| Парткод: | AF04 0588 |
| Деталь: | Exit Spring |
| Парткод: | B044 4154 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Harness - Paper Feed Sensor |
| Парткод: | B129 5203 |
| Деталь: | Gear - 19/28Z |
| Парткод: | H556 2210 |
| Деталь: | STUD |
| Парткод: | H556 2222 |
| Деталь: | Electrode Plate Cover |
| Парткод: | B129 4143 |
| Деталь: | Fusing Frame |
| Парткод: | B129 4102 |
| Деталь: | Thermostat - 160c |
| Парткод: | AW11 0037 |
| Деталь: | Thermistor - Fusing |
| Парткод: | AW10 0088 |
| Деталь: | Thermostat - 170c |
| Парткод: | AW11 0038 |
| Деталь: | Spring - Pickoff Pawl |
| Парткод: | B044 4155 |
| Деталь: | Stripper Pawls |
| Парткод: | AE04 4059 |
| Деталь: | LAMP HOLDER |
| Парткод: | B044 4135 |
| Деталь: | Front Spring Plate |
| Парткод: | B044 4117 |
| Деталь: | GUIDE PLATE |
| Парткод: | H556 2206 |
| Деталь: | Rear Spring Plate |
| Парткод: | B044 4118 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AE02 0149 |
| Деталь: | PRESSURE SPRING |
| Парткод: | B044 4152 |
| Деталь: | PRESSURE LEVER |
| Парткод: | B044 4130 |
| Деталь: | Pressure Release Lever - Front |
| Парткод: | B044 4141 |
| Деталь: | Pressure Release Lever - Rear |
| Парткод: | B044 4146 |
| Деталь: | Side plate |
| Парткод: | B044 4132 |
| Деталь: | Pressure Roller Bushing |
| Парткод: | AE03 1035 |
| Деталь: | Fusing Plate Nut |
| Парткод: | B044 4200 |
| Деталь: | Fusing Harness Cover |
| Парткод: | B044 4201 |
| Деталь: | Warning Decal |
| Парткод: | B044 4161 |
| Деталь: | Pressure Frame |
| Парткод: | B044 4104 |
| Деталь: | Hot Roller Stopper |
| Парткод: | B044 4150 |
| Деталь: | Fusing Gear |
| Парткод: | B044 4170 |
| Деталь: | Fusing Bushing |
| Парткод: | AE03 1044 |
| Деталь: | Hot Roller |
| Парткод: | AE01 1086 |
| Деталь: | Heater - 120V/800W |
| Парткод: | AX44 0202 |
| Деталь: | Heater - 230V:750W |
| Парткод: | AX44 0203 |
| Деталь: | Screw-M3x13 |
| Парткод: | B129 4294 |
| Деталь: | Bushing-pressure Release |
| Парткод: | B044 4131 |
| Деталь: | CUSHION |
| Парткод: | B044 4153 |
| Деталь: | Electrode Plate Fusing |
| Парткод: | B129 4134 |
| Деталь: | GROUND PLATE |
| Парткод: | B044 4136 |
| Деталь: | Paper Holder Stand |
| Парткод: | B044 4401 |
| Деталь: | Front Hot Roller Stopper |
| Парткод: | B044 4156 |
| Деталь: | Hot Roller Cap |
| Парткод: | B044 4112 |
| Деталь: | Holder - Pickoff Pawl |
| Парткод: | B044 4179 |
| Деталь: | Thermostat Plate Nut |
| Парткод: | B129 4195 |
| Деталь: | Gate Plate |
| Парткод: | H556 2208 |
| Деталь: | Reargate Plate Guide |
| Парткод: | H556 2201 |
| Деталь: | Front Gate Plate Guide |
| Парткод: | H556 2202 |
| Деталь: | GEAR BRACKET |
| Парткод: | H556 2219 |
| Деталь: | ROLLER |
| Парткод: | H556 2220 |
| Деталь: | Gate Sensor Harness |
| Парткод: | H556 5106 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x |
| Парткод: | 0450 3010N |
| Деталь: | Carriage:No.1 Unit |
| Парткод: | B262 1700 |
| Деталь: | Flat Cable:Stabilizer |
| Парткод: | B262 5237 |
| Деталь: | Stabilizer-xenon Lamp |
| Парткод: | AZ50 0073 |
| Деталь: | Xenon Lamp:Dia8 |
| Парткод: | AX50 0096 |
| Деталь: | Timing Belt Holder |
| Парткод: | B044 1715 |
| Деталь: | 1st Mirror |
| Парткод: | AC03 0145 |
| Деталь: | 1st Mirror Holder |
| Парткод: | B044 1721 |
| Деталь: | Flat Cable:SBU |
| Парткод: | B262 5236 |
| Деталь: | Lens Unit |
| Парткод: | B262 1770 |
| Деталь: | Bracket:Belt Pulley:Idler:Rear |
| Парткод: | B262 1745 |
| Деталь: | Bracket:Belt Pulley:Idler:Front |
| Парткод: | B262 1741 |
| Деталь: | SCANNER DRIVE PULLEY |
| Парткод: | B039 1785 |
| Деталь: | TENSION SPRING |
| Парткод: | B039 1786 |
| Деталь: | 2nd Scanner |
| Парткод: | B044 1734 |
| Деталь: | Belt:3mm |
| Парткод: | AA04 2053 |
| Деталь: | 2nd Mirror |
| Парткод: | AC03 0146 |
| Деталь: | 2nd Mirror Holder |
| Парткод: | B039 1781 |
| Деталь: | Flat Cable Guide |
| Парткод: | B044 1751 |
| Деталь: | Supporting Plate:Right Upper |
| Парткод: | B262 1683 |
| Деталь: | Exposure Glass Sheet |
| Парткод: | A250 1824 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Bracket:Scale |
| Парткод: | B262 1681 |
| Деталь: | FERRITE CORE |
| Парткод: | H555 5150 |
| Деталь: | Scanner Slider Pin |
| Парткод: | B044 1719 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Paper Tray Unit:NA |
| Парткод: | B262 2511 |
| Деталь: | Paper Tray Unit:EU |
| Парткод: | B262 2510 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B044 2704 |
| Деталь: | Front Side Fence |
| Парткод: | B044 2702 |
| Деталь: | END FENCE |
| Парткод: | B044 2706 |
| Деталь: | SIDE FENCE GEAR |
| Парткод: | G800 3133 |
| Деталь: | Ground Plate:Tray Bottom Plate |
| Парткод: | B262 2709 |
| Деталь: | PRESSURE SPRING |
| Парткод: | B044 2716 |
| Деталь: | Rear Side Fence |
| Парткод: | B044 2703 |
| Деталь: | Joint - Paper Feed Roller |
| Парткод: | B044 2751 |
| Деталь: | Spring - Paper Feed Roller |
| Парткод: | B044 2756 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | B044 2758 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | AF03 1061 |
| Деталь: | Friction pad |
| Парткод: | B044 2710 |
| Деталь: | STOPPER |
| Парткод: | B044 2713 |
| Деталь: | Spring - Release Lever |
| Парткод: | G020 2599 |
| Деталь: | C Ring - Paper Feed Roller |
| Парткод: | H521 3355 |
| Деталь: | Ground Plater |
| Парткод: | B262 2711 |
| Деталь: | Cover:Paper Tray:NA |
| Парткод: | B262 2704 |
| Деталь: | Cover:Paper Tray:EU |
| Парткод: | B262 2703 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 52 152 713 |
| Деталь: | Decal - Cassette Operation |
| Парткод: | B044 2720 |
| Деталь: | PRESSURE SPRING |
| Парткод: | B044 2717 |
| Деталь: | Sponge - End Fence |
| Парткод: | B044 2715 |
| Деталь: | Paper Tray Sheet |
| Парткод: | B044 2721 |
| Деталь: | Rubber Plate - Friction Pad |
| Парткод: | B044 2714 |
| Деталь: | Decal:Misfeed Removal |
| Парткод: | B872 6011 |
| Деталь: | Cover:Open And Close |
| Парткод: | B872 4711 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AF02 2144 |
| Деталь: | Shaft:Pressure:Dia4 |
| Парткод: | B872 4721 |
| Деталь: | Decal:Size:Original |
| Парткод: | B872 6031 |
| Деталь: | Spring Plate:R0 |
| Парткод: | B872 4722 |
| Деталь: | Spring Plate |
| Парткод: | B872 4624 |
| Деталь: | Roller:Reverse:Pressure |
| Парткод: | B872 4616 |
| Деталь: | Cover:Original Table |
| Парткод: | B872 4615 |
| Деталь: | Decal:Side Fence |
| Парткод: | B872 6021 |
| Деталь: | Guide:Original Table:Rear |
| Парткод: | B872 4613 |
| Деталь: | Guide:Original Table:Front |
| Парткод: | B872 4612 |
| Деталь: | Gear - 14Z |
| Парткод: | BB01 3003 |
| Деталь: | Cover:Rear |
| Парткод: | B872 4731 |
| Деталь: | Original Table |
| Парткод: | B872 4611 |
| Деталь: | Original Table:Auxiliary |
| Парткод: | B872 4621 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Cover:Front |
| Парткод: | B872 4741 |
| Деталь: | Decal:Scale:Left:NA |
| Парткод: | B872 6061 |
| Деталь: | Decal:Scale:Left:EU |
| Парткод: | B872 6071 |
| Деталь: | Cap:Registration Sensor:Scale |
| Парткод: | B872 7014 |
| Деталь: | Scale:Left:Adhesion |
| Парткод: | B872 7010 |
| Деталь: | Df Exposure Glass |
| Парткод: | AC01 3005 |
| Деталь: | Sheet - Exposure Glass |
| Парткод: | B044 4929 |
| Деталь: | Screw:DIA3.4:M3 |
| Парткод: | AA14 3866 |
| Деталь: | Case:Magnetic |
| Парткод: | B872 4726 |
| Деталь: | Magnetic:Hale:DIA10x7 |
| Парткод: | G827 1023 |
| Деталь: | Pressure Plate Pad |
| Парткод: | B859 2352 |
| Деталь: | Decal: Caution Chart |
| Парткод: | B872 6081 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0450 3006N |
| Деталь: | Edge Saddle - Les-1010 |
| Парткод: | 11 050 518 |
| Деталь: | Duct Shield |
| Парткод: | B044 1069 |
| Деталь: | Quenching Lamp |
| Парткод: | AX50 0098 |
| Деталь: | Toner Supply Shaft |
| Парткод: | B129 1176 |
| Деталь: | Toner Bottle Drive Spring |
| Парткод: | B129 1175 |
| Деталь: | Spring Clutch:0.7N.m:Z53 |
| Парткод: | AB04 0023 |
| Деталь: | Toner Supply Rail |
| Парткод: | B044 1068 |
| Деталь: | Gear - 64Z |
| Парткод: | AB01 0358 |
| Деталь: | Electrode Plate - Charge |
| Парткод: | AA11 3034 |
| Деталь: | Harness:High Voltage Line:C |
| Парткод: | B262 5220 |
| Деталь: | Harness:High Voltage Line:T |
| Парткод: | B262 5222 |
| Деталь: | Electrode Plate - Transfer |
| Парткод: | AA11 3035 |
| Деталь: | Electrode Plate - Development |
| Парткод: | AA11 3032 |
| Деталь: | Harness:High Voltage Line:B |
| Парткод: | B262 5221 |
| Деталь: | Coupled Gear 22/50z |
| Парткод: | AB01 7582 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | AA14 8651 |
| Деталь: | Drum Shaft |
| Парткод: | AB00 0025 |
| Деталь: | SHUTTER |
| Парткод: | B044 1100 |
| Деталь: | SHUTTER SPRING |
| Парткод: | B044 1101 |
| Деталь: | Development Shaft Assy |
| Парткод: | AB00 0027 |
| Деталь: | Shutter Cover |
| Парткод: | B044 1103 |
| Деталь: | Snap Ring - Pick Up |
| Парткод: | G014 3291 |
| Деталь: | TONER SUPPLY UNIT |
| Парткод: | B262 3020 |
| Деталь: | Bottle Chuck |
| Парткод: | A184 3420 |
| Деталь: | Chuck Shaft |
| Парткод: | B044 3426 |
| Деталь: | Slide Shaft |
| Парткод: | B044 3427 |
| Деталь: | Handlw Cam |
| Парткод: | B044 3461 |
| Деталь: | Chuck Spring - Tonner Bottle |
| Парткод: | A267 3556 |
| Деталь: | Slider Ass`y |
| Парткод: | B044 3485 |
| Деталь: | Cover - Toner Supply Unit |
| Парткод: | B129 3465 |
| Деталь: | Fusing Plate Nut |
| Парткод: | B044 4200 |
| Деталь: | Toner Supply Rail |
| Парткод: | B044 1067 |
| Деталь: | Un Lock Grip |
| Парткод: | B044 3475 |
| Деталь: | Toner Supply Case Ass`y |
| Парткод: | B044 3470 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Connector - 2P |
| Парткод: | 11 026 259 |
| Деталь: | Connector - 3P |
| Парткод: | 11 024 559 |
| Деталь: | Guide Plate:Scanning:Upper |
| Парткод: | B872 3121 |
| Деталь: | Roller:Scanning:Front:Drive |
| Парткод: | B872 3211 |
| Деталь: | Roller:Exit:Drive |
| Парткод: | B872 3221 |
| Деталь: | Guide Plate:Scanning:Lower |
| Парткод: | B872 3111 |
| Деталь: | Photo Refiection Sensor |
| Парткод: | AW01 |
| Деталь: | Discharge Brush:Lower |
| Парткод: | B872 3114 |
| Деталь: | Spring Plate:Guide:Exposure Glass |
| Парткод: | B872 1515 |
| Деталь: | Guide:Exposure Glass |
| Парткод: | B872 1522 |
| Деталь: | Screw - M3 |
| Парткод: | AA14 3544 |
| Деталь: | Exchange Powl:Reverse |
| Парткод: | B872 3311 |
| Деталь: | Spring Plate:Earth:Exit |
| Парткод: | B872 3113 |
| Деталь: | Knob:Pick-up Paper Jam |
| Парткод: | B872 3241 |
| Деталь: | Timing Belt:B40S3M114 |
| Парткод: | AA04 3605 |
| Деталь: | Timing Belt:B40S2M190 |
| Парткод: | G417 3669 |
| Деталь: | Timing Pulley:T32 |
| Парткод: | B872 3223 |
| Деталь: | Pulley:T25 |
| Парткод: | B872 3212 |
| Деталь: | Timing Belt:B40S2M110 |
| Парткод: | AA04 3604 |
| Деталь: | Timing Belt:B40S2M128 |
| Парткод: | AA04 3603 |
| Деталь: | Pulley:T16/T44 |
| Парткод: | B872 4214 |
| Деталь: | Tension Spring:Motor:Transport |
| Парткод: | B872 4216 |
| Деталь: | Stepper Motor:DC24V 3.35W |
| Парткод: | B872 5820 |
| Деталь: | Bracket:Motor:Transport |
| Парткод: | B872 4210 |
| Деталь: | Timing Pulley:T32 |
| Парткод: | B872 3222 |
| Деталь: | Tension Spring:Exchange Powl |
| Парткод: | B872 3313 |
| Деталь: | Lever:Exchange Powl |
| Парткод: | B872 3312 |
| Деталь: | DC Solenoid:Exchange Powl |
| Парткод: | B872 4310 |
| Деталь: | Harness:Dc Solenoid |
| Парткод: | B872 5250 |
| Деталь: | Pulley Idler |
| Парткод: | A859 4141 |
| Деталь: | Inner Cover:Left Rear |
| Парткод: | B872 4131 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | BUSHING - 6MM |
| Парткод: | 8 053 480 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Screw - M3X4 |
| Парткод: | 0353 0040N |
| Деталь: | Scanner Bracket - Front Right |
| Парткод: | B262 1064 |
| Деталь: | Scanner Stud |
| Парткод: | B044 1063 |
| Деталь: | Guide Plate - Paper Feed |
| Парткод: | B044 2653 |
| Деталь: | Paper Feedguide |
| Парткод: | B044 2654 |
| Деталь: | C Ring - Paper Feed Roller |
| Парткод: | H521 3355 |
| Деталь: | Magnetic Clutch:0.25N.m:Z43 |
| Парткод: | AX20 0308 |
| Деталь: | Rear bushing |
| Парткод: | B044 2605 |
| Деталь: | Registration Roller |
| Парткод: | AF02 0686 |
| Деталь: | Photointerruptor:Lg248nl11 |
| Парткод: | GW02 0020 |
| Деталь: | Registration Electrode Plate |
| Парткод: | B044 1102 |
| Деталь: | Front bushing |
| Парткод: | B044 2604 |
| Деталь: | Harness - Front Right Switch |
| Парткод: | B129 5211 |
| Деталь: | Registration Feeler |
| Парткод: | B044 2603 |
| Деталь: | Support Bushing |
| Парткод: | B044 2616 |
| Деталь: | Turn Roller |
| Парткод: | B044 2602 |
| Деталь: | Exit Guide |
| Парткод: | B044 2814 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0322 |
| Деталь: | Friction Pad - Manual Feed |
| Парткод: | B044 2815 |
| Деталь: | Fricion Pad Spring |
| Парткод: | B044 2817 |
| Деталь: | By-pass Feed Roller |
| Парткод: | AF03 1086 |
| Деталь: | Harness:Paper End Sensor |
| Парткод: | B262 5218 |
| Деталь: | Manual Feed Shaft |
| Парткод: | B044 2829 |
| Деталь: | Guide Plate - Manual Feed |
| Парткод: | B044 2811 |
| Деталь: | By-pass Paper End Sensor |
| Парткод: | G020 2772 |
| Деталь: | Manual Feed Bracket |
| Парткод: | B044 2812 |
| Деталь: | Spacer-manual Feed Roller |
| Парткод: | B044 2825 |
| Деталь: | Cushion-manual Feed Roller |
| Парткод: | B044 2824 |
| Деталь: | Magnetic Clutch:0.25N.m:Z43 |
| Парткод: | AX20 0310 |
| Деталь: | Guide Plate Stopper |
| Парткод: | B044 2656 |
| Деталь: | Spacer - Registration |
| Парткод: | B044 2622 |
| Деталь: | Fusing Plate Nut |
| Парткод: | B044 4200 |
| Деталь: | MICRO SWITCH |
| Парткод: | 12 042 521 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0450 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | WIRE SADDLE |
| Парткод: | 11 050 197 |
| Деталь: | Guide Plate:Paper Feed:Upper |
| Парткод: | B872 2312 |
| Деталь: | Pad - Pick-up |
| Парткод: | H521 1350 |
| Деталь: | Guide Plate:Paper Feed:Upper |
| Парткод: | B872 2311 |
| Деталь: | Feeder Unit |
| Парткод: | B872 2510 |
| Деталь: | Bracket:Magnetic Clutch |
| Парткод: | B872 2412 |
| Деталь: | Magnetic Clatch:Ass`y |
| Парткод: | B872 2420 |
| Деталь: | Harness:Main |
| Парткод: | B872 5240 |
| Деталь: | HARNESS:INTERFACE |
| Парткод: | B872 5210 |
| Деталь: | PCB:Main Control |
| Парткод: | B872 5100 |
| Деталь: | Spacer:DIA9 |
| Парткод: | B872 2524 |
| Деталь: | Spring Clutch:Feed:DIA6 |
| Парткод: | B872 2523 |
| Деталь: | Shaft:Feed:C |
| Парткод: | B872 2521 |
| Деталь: | Feeler:Original Sensor |
| Парткод: | B872 2513 |
| Деталь: | Shaft:Pickup |
| Парткод: | B872 2514 |
| Деталь: | Gear:Z18 |
| Парткод: | B872 2512 |
| Деталь: | Spring:Roller Clutch |
| Парткод: | B872 2526 |
| Деталь: | Spacer:Pickup |
| Парткод: | B872 2522 |
| Деталь: | FEED ROLLER |
| Парткод: | AF03 1062 |
| Деталь: | Roller Clutch:Bracket:Feed |
| Парткод: | B872 2527 |
| Деталь: | Cushion:Bracket:Feed |
| Парткод: | B872 2515 |
| Деталь: | Gear:Idler:Z16 |
| Парткод: | B872 2511 |
| Деталь: | Oneway Clutch |
| Парткод: | B044 4961 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Gear:Z18 |
| Парткод: | B872 2528 |
| Деталь: | Collar:Pickup |
| Парткод: | B872 2529 |
| Деталь: | pickup roller |
| Парткод: | AF03 0363 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Clamp:EDS-0704L-V0 |
| Парткод: | 11 050 612 |
| Деталь: | Locking Support - KGCP-08-0 |
| Парткод: | 11 050 436 |
| Деталь: | Scale:Inner Back:EU |
| Парткод: | B262 1847 |
| Деталь: | Scale:Inner Back:NA |
| Парткод: | B262 1848 |
| Деталь: | SHOULDER SCREW |
| Парткод: | B044 1847 |
| Деталь: | Operation Panel:NA (B262/B292) |
| Парткод: | B262 1412 |
| Деталь: | Operation Panel:EU (B262/B292) |
| Парткод: | B262 1413 |
| Деталь: | Operation Panel:Asia (B280) |
| Парткод: | B262 1414 |
| Деталь: | Operation Panel:EU (B280/B293) |
| Парткод: | B262 1415 |
| Деталь: | Model Name Plate:INF (B280) |
| Парткод: | B280 7509 |
| Деталь: | Model Name Plate:SVN (B292) |
| Парткод: | B292 7508 |
| Деталь: | Model Name Plate:RIC (B293) |
| Парткод: | B293 7500 |
| Деталь: | Model Name Plate:REX (B292) |
| Парткод: | B293 7501 |
| Деталь: | Model Name Plate:NSA (B292) |
| Парткод: | B293 7502 |
| Деталь: | Model Name Plate:GES (B292) |
| Парткод: | B293 7503 |
| Деталь: | Model Name Plate:LAN (B292) |
| Парткод: | B293 7504 |
| Деталь: | Model Name Plate:INF (B292) |
| Парткод: | B293 7509 |
| Деталь: | Model Name Plate:RIC (B262/B292) |
| Парткод: | B262 7500 |
| Деталь: | Model Name Plate:REX (B262) |
| Парткод: | B262 7501 |
| Деталь: | Model Name Plate:NSA (B262) |
| Парткод: | B262 7502 |
| Деталь: | Model Name Plate:GES:EU (B262) |
| Парткод: | B262 7503 |
| Деталь: | Model Name Plate:LAN (B262) |
| Парткод: | B262 7504 |
| Деталь: | Model Name Plate:GES:NA (B262/B292) |
| Парткод: | B262 7506 |
| Деталь: | Model Name Plate:LAN (B262/B292) |
| Парткод: | B262 7507 |
| Деталь: | Model Name Plate:RIC (B280) |
| Парткод: | B280 7500 |
| Деталь: | Model Name Plate:REX (B280) |
| Парткод: | B280 7501 |
| Деталь: | Model Name Plate:NSA (B280) |
| Парткод: | B280 7502 |
| Деталь: | Model Name Plate:GES (B280) |
| Парткод: | B280 7503 |
| Деталь: | Model Name Plate:LAN (B280) |
| Парткод: | B280 7504 |
| Деталь: | Model Name Plate:GES:AA (B280) |
| Парткод: | B280 7505 |
| Деталь: | Cover:IC Card |
| Парткод: | B262 1253 |
| Деталь: | Decal - Paper Size |
| Парткод: | H555 2790 |
| Деталь: | Shielding Plate |
| Парткод: | B044 1258 |
| Деталь: | Exit Cover EU |
| Парткод: | B129 1252 |
| Деталь: | Exit Cover NA |
| Парткод: | B129 1262 |
| Деталь: | Extension Tray - EU |
| Парткод: | B044 1284 |
| Деталь: | Extension Tray - NA |
| Парткод: | B044 1285 |
| Деталь: | END FENCE |
| Парткод: | B044 1254 |
| Деталь: | Exposure Glass |
| Парткод: | AC01 2070 |
| Деталь: | Scale:Left:Na |
| Парткод: | B262 1805 |
| Деталь: | Scale:Left:EU |
| Парткод: | B262 1802 |
| Деталь: | PLATE HOLDER |
| Парткод: | H555 4190 |
| Деталь: | Left Scanner Cover NA |
| Парткод: | B129 1261 |
| Деталь: | Left Scanner Cover EU |
| Парткод: | B129 1251 |
| Деталь: | Cover:Rear:EU |
| Парткод: | B262 1250 |
| Деталь: | Cover:Scanner:Right:NA |
| Парткод: | B262 1266 |
| Деталь: | Cover:Scanner:Right:EU |
| Парткод: | B262 1256 |
| Деталь: | Front Right Coveer |
| Парткод: | B044 1279 |
| Деталь: | RIGHT UPPER COVER |
| Парткод: | B044 1278 |
| Деталь: | Sheet - Operation Instructions |
| Парткод: | B044 1290 |
| Деталь: | Front door |
| Парткод: | B044 1286 |
| Деталь: | Plate:Logotype:RIC |
| Парткод: | H310 4120 |
| Деталь: | Plate:Logotype:SAV |
| Парткод: | H555 4182 |
| Деталь: | Plate:Logotype:H555:LAN |
| Парткод: | H555 4183 |
| Деталь: | Plate:Logotype:H555:INF |
| Парткод: | H555 4184 |
| Деталь: | Plate:Logotype:H555:NSA |
| Парткод: | H555 4185 |
| Деталь: | Plate:Logotype:H555:REX |
| Парткод: | H555 4186 |
| Деталь: | Plate:Logotype:H555:GES |
| Парткод: | H555 4187 |
| Деталь: | Plate:Exposure Glass |
| Парткод: | B262 1258 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | FERRITE CORE |
| Парткод: | 16071461 |
| Деталь: | Fan Motor:MM80 DC24V 3.12W |
| Парткод: | GX64 5734 |
| Деталь: | Power Pack BCT |
| Парткод: | AZ32 0152 |
| Деталь: | Harness:HVP |
| Парткод: | B262 5217 |
| Деталь: | Harness:HPS |
| Парткод: | B262 5201 |
| Деталь: | Harness:Paper Feed Sensor |
| Парткод: | B262 5202 |
| Деталь: | Harness - Registration Sensor |
| Парткод: | B129 5213 |
| Деталь: | Harness:Toner:Connecting |
| Парткод: | B262 5200 |
| Деталь: | Harness - Power Supply Unit |
| Парткод: | B262 5206 |
| Деталь: | Harness:Motor:Main |
| Парткод: | B262 5216 |
| Деталь: | Harness:Operation Panel |
| Парткод: | B262 5205 |
| Деталь: | Harness:Door Switch |
| Парткод: | B262 5210 |
| Деталь: | PCB:BICU |
| Парткод: | B262 5101 |
| Деталь: | PCB:BICU:Asia |
| Парткод: | B262 5103 |
| Деталь: | BICU Insulating Sheet |
| Парткод: | B129 1307 |
| Деталь: | Insulating Sheet Power Pack |
| Парткод: | AA17 0026 |
| Деталь: | BICU Shadeing Plate |
| Парткод: | B129 1301 |
| Деталь: | Power Supply Cord NA |
| Парткод: | B129 5021 |
| Деталь: | Power Supply Cord:Stopper:Eu:Ass`y |
| Парткод: | B262 5023 |
| Деталь: | Harness - Paper Feed Table |
| Парткод: | B129 5223 |
| Деталь: | Spring Plate - Gwctl |
| Парткод: | B129 1313 |
| Деталь: | Rear Cover Bracket |
| Парткод: | B129 1303 |
| Деталь: | Power Supply Unit:100V |
| Парткод: | AZ23 0161 |
| Деталь: | Power Supply Unit:200V |
| Парткод: | AZ23 0162 |
| Деталь: | Harness:AC:Fusing:NA |
| Парткод: | B262 5209 |
| Деталь: | Harness:AC:Fusing:EU |
| Парткод: | B262 5208 |
| Деталь: | Total Counter:7FIG:24V |
| Парткод: | AX31 0049 |
| Деталь: | Holder:Ferrite Core |
| Парткод: | B262 5805 |
| Деталь: | FERRITE CORE |
| Парткод: | H555 5150 |
| Деталь: | Flat Cable:SBU |
| Парткод: | B262 5236 |
| Деталь: | Bracket:Basic |
| Парткод: | B262 1314 |
| Деталь: | Tapping Screw:3x35 |
| Парткод: | 0450 3035N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Screw - M4X6 |
| Парткод: | 0950 4006N |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11 050 522 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | PAPER GUIDE |
| Парткод: | B044 2808 |
| Деталь: | By-pass Feed Table |
| Парткод: | B044 2801 |
| Деталь: | LEVER SHAFT |
| Парткод: | B259 2786 |
| Деталь: | Lever - Manual Feed Table |
| Парткод: | B044 2806 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Spring - Manual Feed Table |
| Парткод: | B044 2809 |
| Деталь: | Front Side Fence |
| Парткод: | B044 2804 |
| Деталь: | Rear Side Fence |
| Парткод: | B044 2805 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B044 2803 |
| Деталь: | SIDE FENCE GEAR |
| Парткод: | G800 3133 |
| Деталь: | Stay - Tray Bottom Plate |
| Парткод: | B044 2807 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 52 152 713 |
| Деталь: | Manual Feed Decal |
| Парткод: | AA00 3011 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | GUIDE PLATE |
| Парткод: | B044 2612 |
| Деталь: | Registration Roller Shaft |
| Парткод: | B044 2624 |
| Деталь: | SPRING HOLDER |
| Парткод: | B044 4618 |
| Деталь: | Driven Roller Bushing |
| Парткод: | B044 2614 |
| Деталь: | Driven Roller - Front Rear |
| Парткод: | AF02 2139 |
| Деталь: | Middle Driven Roller |
| Парткод: | AF02 2140 |
| Деталь: | Right Door Spring |
| Парткод: | AA06 3409 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | B262 3802 |
| Деталь: | Positioning Spring - Transfer Roller |
| Парткод: | B044 3990 |
| Деталь: | Transfer Roller Spring - Rear |
| Парткод: | B044 3866 |
| Деталь: | Transfer Roller Spring - Front |
| Парткод: | B044 3865 |
| Деталь: | TRANSFER PLATE |
| Парткод: | B044 3860 |
| Деталь: | PRESSURE SPRING |
| Парткод: | B044 2615 |
| Деталь: | Transfer Guide |
| Парткод: | B044 3870 |
| Деталь: | Density Sensor:Longdist:Adhesion |
| Парткод: | B044 3894 |
| Деталь: | Harness:Density Sensor |
| Парткод: | B262 5214 |
| Деталь: | Bushing - Driven Roller |
| Парткод: | B044 2621 |
| Деталь: | Reverse Guide Plate |
| Парткод: | B044 4663 |
| Деталь: | Separation Plate |
| Парткод: | B044 3857 |
| Деталь: | Right Door Belt |
| Парткод: | B044 4624 |
| Деталь: | Right Cover Lever |
| Парткод: | B044 4616 |
| Деталь: | RIGHT DOOR |
| Парткод: | B044 4655 |
| Деталь: | Discharge Plate |
| Парткод: | B044 3859 |
| Деталь: | Fusing Unit Decal |
| Парткод: | B044 4617 |
| Деталь: | GUIDE PLATE |
| Парткод: | H556 2818 |
| Деталь: | Duplex Guide Plate Assy |
| Парткод: | B262 4154 |
| Деталь: | Guide Roller |
| Парткод: | AF02 2143 |
| Деталь: | Myler Reverse |
| Парткод: | H556 2820 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 3443 |
| Деталь: | Right Guide Plate |
| Парткод: | H556 4192 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 2033 |
| Деталь: | Positioning Roller |
| Парткод: | H556 4186 |
| Деталь: | Spring Plate |
| Парткод: | H556 4181 |
| Деталь: | Transport Roller Holder |
| Парткод: | H556 4185 |
| Деталь: | Transport Driven Roller |
| Парткод: | AF02 2152 |
| Деталь: | Transport Roller |
| Парткод: | H556 4190 |
| Деталь: | SHEET |
| Парткод: | H556 4188 |
| Деталь: | SHEET |
| Парткод: | H556 4189 |
| Деталь: | Front Stopper Plate |
| Парткод: | B044 2860 |
| Деталь: | Rear Stopper Plate |
| Парткод: | B044 2861 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Torsion Spring:Pressure:Front |
| Парткод: | B872 1923 |
| Деталь: | Lever:Driven:Pressure |
| Парткод: | B872 1921 |
| Деталь: | Torsion Spring:Pressure:Rear |
| Парткод: | B872 1924 |
| Деталь: | Roller:Driven:Scanning:Front |
| Парткод: | B872 1922 |
| Деталь: | Bushing:Exit |
| Парткод: | B872 1934 |
| Деталь: | Exit Roller:Driven |
| Парткод: | B872 1931 |
| Деталь: | Compression Spring:Exit:Driven |
| Парткод: | B872 1933 |
| Деталь: | Cap:Paper Feed Sensor:Base |
| Парткод: | B872 1912 |
| Деталь: | Bracket:Side Plate:Rear Right |
| Парткод: | B872 1114 |
| Деталь: | Hinge:Left |
| Парткод: | B872 1414 |
| Деталь: | Hinge:Right |
| Парткод: | B872 1421 |
| Деталь: | Decal:Lever:Knob |
| Парткод: | B872 6041 |
| Деталь: | Tape:Pressuer Plate |
| Парткод: | B351 4322 |
| Деталь: | Pressure plate |
| Парткод: | B872 4510 |
| Деталь: | Tape:Pressure Plate:Left |
| Парткод: | B872 4513 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11 050 508 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Gear - 27Z |
| Парткод: | BB01 3006 |
| Деталь: | Coupled Gear - 43/53z |
| Парткод: | AB01 7586 |
| Деталь: | Gear - 41Z |
| Парткод: | AB01 1438 |
| Деталь: | GEAR - 29Z |
| Парткод: | AB01 1492 |
| Деталь: | Magnetic Clutch:0.25N.m:Z43 |
| Парткод: | AX20 0309 |
| Деталь: | COLLAR |
| Парткод: | AA13 2217 |
| Деталь: | Coupled Gear - 17/44z |
| Парткод: | AB01 7587 |
| Деталь: | Coupled Gear - 17/44z |
| Парткод: | AB01 7585 |
| Деталь: | Gear - 19/21Z |
| Парткод: | AB01 7629 |
| Деталь: | Gear - 18/40Z |
| Парткод: | AB01 7663 |
| Деталь: | Fusing Bracket Assy |
| Парткод: | B129 1164 |
| Деталь: | Fusing Shaft 5 |
| Парткод: | AA14 3804 |
| Деталь: | Rear Drive Plate 2 |
| Парткод: | B129 1110 |
| Деталь: | Bracket Cushion |
| Парткод: | AA16 1157 |
| Деталь: | SHAFT SPACER |
| Парткод: | B129 1056 |
| Деталь: | Lever DC Solenoid Ass`y |
| Парткод: | B129 1161 |
| Деталь: | Spring - Swivel Fusing |
| Парткод: | AA06 2326 |
| Деталь: | Plate Cushion |
| Парткод: | B129 1129 |
| Деталь: | Damping Insulation |
| Парткод: | B044 1139 |
| Деталь: | Ground Plate - Drum Drive |
| Парткод: | AA12 0124 |
| Деталь: | Ground Plate - Registration |
| Парткод: | AA12 0104 |
| Деталь: | Side Plate - Manual Feed |
| Парткод: | B129 1157 |
| Деталь: | Ground Plate - Manual Feed |
| Парткод: | B129 2820 |
| Деталь: | Duplex Drive Bracket |
| Парткод: | H556 4172 |
| Деталь: | Stepper Motor-Duplex-DC24V 14.9W |
| Парткод: | AX06 0336 |
| Деталь: | Ground Plate - Lower Duplex Bracket |
| Парткод: | B129 4703 |
| Деталь: | Spring Plate:Discharge |
| Парткод: | B262 4701 |
| Деталь: | Brushless Motor:DC24V:20W |
| Парткод: | AX06 0344 |
| Деталь: | Gear - 19/38Z |
| Парткод: | AB01 7628 |
| Деталь: | Rear Drive Plate 1 Assy |
| Парткод: | B129 1163 |
| Деталь: | Swivel Bracket |
| Парткод: | H556 4183 |
| Деталь: | Spring Plate |
| Парткод: | H556 4178 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3582 |
| Деталь: | Pulley - 24Z |
| Парткод: | AB03 2071 |
| Деталь: | Plate Bracket |
| Парткод: | H556 4180 |
| Деталь: | Bushing - Cleaning Roller |
| Парткод: | 54 244 142 |
| Деталь: | Gear - 29/69Z |
| Парткод: | AB01 7661 |
| Деталь: | Gear - 44/67Z |
| Парткод: | AB01 7660 |
| Деталь: | Gear - 17/67Z |
| Парткод: | AB01 7662 |
| Деталь: | Gear - 49Z |
| Парткод: | AB01 0362 |
| Деталь: | Gear - 43/91Z |
| Парткод: | AB01 7659 |
| Деталь: | BRACKET |
| Парткод: | B044 1158 |
| Деталь: | Gear - 28/43Z |
| Парткод: | AB01 7627 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0453 3006N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | WIRE SADDLE |
| Парткод: | 11 050 197 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | LASER UNIT |
| Парткод: | B262 1901 |
| Деталь: | GROUND PLATE |
| Парткод: | B044 1943 |
| Деталь: | Harness:Lddr:Connecting |
| Парткод: | B262 5204 |
| Деталь: | Shutter Plate |
| Парткод: | B044 1944 |
| Деталь: | Harness:Polygon Scanner |
| Парткод: | B262 5207 |
| Деталь: | Polygon Scannermotor-dc24v |
| Парткод: | AX06 0342 |
| Деталь: | Laser Diode Unit:Ass`y |
| Парткод: | B044 1912 |
| Деталь: | Cylindrical Lens |
| Парткод: | G025 2730 |
| Деталь: | Syinchronizing Detector Lens |
| Парткод: | G025 2731 |
| Деталь: | Shield Glass |
| Парткод: | B044 1931 |
| Деталь: | Laser Unit Cover |
| Парткод: | B044 1941 |
| Деталь: | LD Decal |
| Парткод: | G029 1982 |
| Деталь: | Seal - LDU |
| Парткод: | B044 1906 |
| Деталь: | Spacer - 5mm |
| Парткод: | B044 1999 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Binding Self-tapping Screw:3x10 |
| Парткод: | 0452 3010N |
| Деталь: | Scanner Unit Stay |
| Парткод: | B044 1060 |
| Деталь: | Guide -paper Dust Remover |
| Парткод: | B262 2623 |
| Деталь: | Ground Wire:Cassette |
| Парткод: | B262 5235 |
| Деталь: | BICU Shadeing Plate |
| Парткод: | B129 1301 |
| Деталь: | BICU Bracket |
| Парткод: | B129 1300 |
| Деталь: | RUBBER FOOT |
| Парткод: | G512 3029 |
| Деталь: | Right Rail |
| Парткод: | B044 2651 |
| Деталь: | Paper End Sensor |
| Парткод: | B044 5300 |
| Деталь: | PSU Stay |
| Парткод: | B129 1060 |
| Деталь: | Ground Plate - Option Tray |
| Парткод: | B044 1066 |
| Деталь: | Positioning Plate - Toner Bottle |
| Парткод: | B044 1105 |
| Деталь: | Base Bracket |
| Парткод: | B044 1061 |
| Деталь: | Base Bracket - Paper Feed |
| Парткод: | B044 1062 |
| Деталь: | Mylar-quenching Lamp |
| Парткод: | B044 2202 |
| Деталь: | Separation Bracket |
| Парткод: | B129 1315 |
| Деталь: | Power Supply Unit Bracket |
| Парткод: | B129 1302 |
| Деталь: | Holder Ass`y - Paper Dust Removal |
| Парткод: | B044 2617 |
| Деталь: | Harness Holder Bracket |
| Парткод: | B044 1998 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Screw - M3x8 |
| Парткод: | 0954 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Card Spacer- 6.4mm |
| Парткод: | 11 050 409 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11 050 522 |
| Деталь: | Operation Panel:NA (B262/B292) |
| Парткод: | B262 1412 |
| Деталь: | Operation Panel:EU (B262/B292) |
| Парткод: | B262 1413 |
| Деталь: | Operation Panel:Asia (B280) |
| Парткод: | B262 1414 |
| Деталь: | Operation Panel:EU (B280/B293) |
| Парткод: | B262 1415 |
| Деталь: | Cover:On-line:Dummy |
| Парткод: | B262 1471 |
| Деталь: | Cover:Fax:Dummy |
| Парткод: | B262 1473 |
| Деталь: | Cover:On-line:CPS:NA |
| Парткод: | B262 1479 |
| Деталь: | Cover:On-line:CPS:EU |
| Парткод: | B262 1481 |
| Деталь: | Keytop - Cursor |
| Парткод: | B243 1459 |
| Деталь: | Keytop - 10key |
| Парткод: | B229 1475 |
| Деталь: | Keytop - 10key NA |
| Парткод: | B229 1526 |
| Деталь: | Keytop - 10key Asia |
| Парткод: | B229 1557 |
| Деталь: | Keytop - Initial |
| Парткод: | B229 1525 |
| Деталь: | Keytop - Clear Modes |
| Парткод: | B229 1537 |
| Деталь: | Keytop - Power Source |
| Парткод: | B243 1458 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B229 1454 |
| Деталь: | Keytop - Start |
| Парткод: | B229 1453 |
| Деталь: | PCB:OPU |
| Парткод: | B262 1550 |
| Деталь: | Spring Plate - STL |
| Парткод: | B129 1474 |
| Деталь: | LCD |
| Парткод: | B262 1495 |
| Деталь: | Front Idler Bracket |
| Парткод: | B044 1827 |
| Деталь: | Timing Belt:ST55 |
| Парткод: | AA04 3997 |
| Деталь: | Rear Idler Bracket |
| Парткод: | B044 1828 |
| Деталь: | Spring - Timing Pulley |
| Парткод: | B039 1704 |
| Деталь: | Rail:Rear |
| Парткод: | B262 1654 |
| Деталь: | Rail:Front |
| Парткод: | B262 1653 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Bracket:Scale:Inner Back |
| Парткод: | B262 1665 |
| Деталь: | Sheet:Flat Cable:Stabilizer |
| Парткод: | B262 1663 |
| Деталь: | Lens Bracket |
| Парткод: | B044 1663 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B262 1811 |
| Деталь: | Drive Pully - 41t/37t |
| Парткод: | AB03 3095 |
| Деталь: | Flange - Pulley |
| Парткод: | B039 1695 |
| Деталь: | Scanner Drive Shaft |
| Парткод: | B044 1826 |
| Деталь: | Stepper Motor:Dc24v 5.3w |
| Парткод: | B262 1814 |
| Деталь: | Gear - 53Z/60Z |
| Парткод: | B121 1680 |
| Деталь: | Timing Belt L147 |
| Парткод: | B121 1696 |
| Деталь: | Tension Spring - Stepper Motor |
| Парткод: | B039 1683 |
| Деталь: | Drive Pully - 37t |
| Парткод: | AB03 0711 |
| Деталь: | Bracket:Stopper:Rear |
| Парткод: | B262 1670 |
| Деталь: | Belt Clamp Bracket |
| Парткод: | B044 1661 |
| Деталь: | BRACKET |
| Парткод: | B044 1671 |
| Деталь: | Stopper Bracket - 1st Scanner |
| Парткод: | B044 1669 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006P |
| Деталь: | Ball Bearing - 6x15x5 |
| Парткод: | 7 403 906 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
Коды ошибок
101
120
121
141
142
144
145
193
198
302
320
321
322
390
391
392
401
402
500
541
542
543
544
545
546
547
559
590
632
634
635
692
694
760
761
762
901
903
928
929
981
982
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 141 |
| Display: | SVC 141 ERROR |
| Description: | Motor |
| Causes: | • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor excessive PWM - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board” |
| Error code: | 142 |
| Display: | Contact the Service center. 142: Error |
| Description: | Motor |
| Causes: | • Standard white plate defective, dirty • Moisture inside the scanner unit • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor, over speed - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 145 |
| Display: | SYSTEM HALT (*) 145 : MAIN CN6,9 CHK |
| Description: | Motor |
| Causes: | • Exposure lamp defective • Dirty white plate • Incorrect position or width of white plate scanning (SP4015) • BICU board defective • SBU board defective |
| Remedy: | DC motor excessive PWM autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 193 |
| Description: | Image transfer error The IPU board does not finish within 1 minute after the image data has been transferred to the controller board. |
| Causes: | • IPU board defective • Controller board defective • Video controller defective |
| Error code: | 198 |
| Description: | Memory address error The IPU board does not receive the memory address from the controller board. |
| Causes: | • Mismatched firmware between the SBCU board and controller board • Controller defective • SBCU defective • IPU board defective Note: Before you replace a board, update the firmware. This can repair the error. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 320 |
| Display: | Reset fuser 320: Fuser error |
| Description: | Same unit not detected upon power ON or opening cover. |
| Causes: | 1) Is error message displayed? 2) Is fuser unit set properly? 3) Does error reoccur? |
| Remedy: | Check if fuser is set properly. Reset fuser and turn ON power again. Replace fuser unit assembly. |
| Error code: | 321 |
| Display: | Turn power OFF and wait 321: MOTOR OVERHEAT |
| Description: | Printer cannot be used temporarily due to motor overheat. |
| Remedy: | Turn ON power after a while. |
| Error code: | 322 |
| Description: | Synchronization error The synchronization signal was not issued within 500 ms after the LD fired while the polygon motor was turning at the prescribed number of revolutions. |
| Causes: | • Laser synchronization board connectors or harness loose, disconnected, or damaged • Laser synchronization board defective or out of position • LD drive board defective |
| Remedy: | 1. Check the harness connection of the development HVPS. 2. Replace the development HVPS. 3. Replace the development unit. |
| Error code: | 390 |
| Display: | Check MP tray 390: Paper jam |
| Description: | Paper jam during paper feed from MT. |
| Causes: | Check for miss-fed paper around MT cassette. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace MT. |
| Error code: | 391 |
| Description: | TD sensor error: Auto adjust error During automatic adjustment of the TD sensor, output voltage was less than 1.8V, or more than 4.8V during TD sensor initial setting |
| Causes: | • TD sensor connector or harness loose, broken, defective • TD sensor defective • IOB defective • Toner supply defective (confirm that the toner seal strip has been removed from toner cartridge) |
| Remedy: | 1. Check the harness or harness connection. 2. Clean the surface of the quenching lamp glass. |
| Error code: | 392 |
| Description: | Development Bias Error The development bias feedback voltage was less than 0.3 V for longer than 200 ms while the PWM duty value was more than 5% (indicating a development bias leak). |
| Causes: | • Bias terminal damaged • High voltage cable damaged, defective • CGB power pack defective |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 500 |
| Description: | Transport/Fusing Motor Error |
| Causes: | The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the transport/fusing motor. Replace it if necessary. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 590 |
| Description: | Toner collection motor error The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on. |
| Causes: | • Motor lock due to obstruction • Motor driver board defective • Motor connection loose, defective • Toner collection motor sensor disconnected, sensor defective • Rotational transmission shaft (o6 x 30) missing |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 692 |
| Description: | GAVD block 12C bus error The I2C bus of the BICU is defective |
| Causes: | • Replace BICU |
| Error code: | 694 |
| Description: | Controller board communication abnormal Communication error between the scanner part of the controller board and BICU. |
| Causes: | • The connector is abnormal between the controller board and the BICU board. |
| Error code: | 760 |
| Description: | Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Punch HP sensor disconnected, defective • Punch motor disconnected or defective • Punch motor overload due to obstruction |
| Remedy: | 1. Check the connections and cables for the punch motor and HP sensor. 2. Check for blockages in the punch motor mechanism. 3. Replace the punch HP sensor and/or punch motor 4. Replace the finisher main board. |
| Error code: | 761 |
| Description: | Finisher folder plate motor error The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Remedy: | 1. Check the connections and cables for the folder plate motor and HP sensor. 2. Check for blockages in the folder plate motor mechanism. 3. Replace the folder plate HP sensor and/or folder plate motor 4. Replace the finisher main board. |
| Error code: | 762 |
| Description: | Front fold plate HP sensor error The state (on/off, off/on) of the front fold plate HP sensor in the fan fold unit did not change 1 sec. after the plate started to move. |
| Causes: | • Fold plate motor (F) harness connector loose, disconnected, broken • Front fold plate HP sensor harness connector loose, disconnected, broken • Fold plate motor (F) defective • Front fold plate HP sensor defective • Undetected paper is jamming the action of the motor or fold plate • Fan folder unit MCU defective |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 903 |
| Display: | Power OFF/ON 903:Error |
| Description: | Paperport link driver error |
| Causes: | These errors indicate an unrecoverable system software error. |
| Remedy: | Replace the system board. |
| Error code: | 928 |
| Display: | Power Off/on 928: Error |
| Description: | Failure in the Fuser Motor The Fuser Motor has stopped rotating. Applicable Status Code: Code 928: The Fuser Motor has failed. |
| Causes: | • Fuser Motor, PL2.1.9 • Motor Driver Board, PL2.1.10 • Engine Control Board, PL1.1.4 |
| Remedy: | 1 Test the Fuser Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Fuser Motor test. Does the motor operate? Complete. Replace the motor. If the error persists, go to Step 2. 2 Check for +24 V to the Fuser Motor. Is the +24 V across DCHEAT- 3 <=> ground? Go to Step 5. Go to Step 3. 3 Check Motor Driver Board POW24 connector for 24 V. 1. Disconnect POW24. Is the +24 V across POW24 pins 1 and 2? Replace the Motor Driver Board. Go to Step 4. 4 Check for 24 V at the LVPS 1. Disconnect CN2 on the LVPS. Is the +24 V across pins 1 and 2? Replace the POW24 Harness. Replace the LVPS. 5 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 929 |
| Display: | Power Off/on 929: Error |
| Description: | Failure in the Waste Toner Motor The Waste Toner Motor has stopped rotating. Applicable Status Code: Code 929: The Waste Toner Motor has failed. |
| Causes: | • Waste Toner Motor, PL7.1.3 • Motor Driver Board, PL2.1.10 • Engine Control Boar d, PL1.1.4 |
| Remedy: | 1 Test the Waste Toner Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Waste Toner Motor test. Does the motor operate? Complete. Replace the motor. If the error persists, go to Step 2. 2 Check for +24 V to the Waste Toner Motor. Is the +24 V across WTDC- 3 <=> ground? Go to Step 5. Go to Step 3. 3 Check Motor Driver Board POW24 connector for 24 V. 1. Disconnect POW24. Is the +24 V across POW24 pins 1 and 2? Replace the Motor Driver Board. Go to Step 4. 4 Check for 24 V at the LVPS 1. Disconnect CN2 on the LVPS. Is the +24 V across pins 1 and 2? Replace the POW24 Harness. Replace the LVPS. 5 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 981 |
| Display: | Service call 981: Error |
| Description: | <device> |
| Causes: | • Defective NVRAM • Loose connection between the BICU and the NVRAM • Incorrect installation of the NVRAM • Defective BICU |
| Remedy: | The engine protocol violation detected by the specified device. |
| Error code: | 982 |
| Display: | Service call 982: Error |
| Description: | <device> Comm |
| Causes: | • Localization setting not specified (The main power switch is turned on for the first time after the NVRAM is replaced.) • Incorrect localization setting • Defective NVRAM |
| Remedy: | Communications error detected by the specified device. |
