Ricoh MP2553
Рейтинг
Модули
Fusing Section 1
BY-PASS FEED SECTION
Duplex Section 4
Drive Section 1
FUSING SECTION 2
Controller Option 2
PAPER FEED SECTION 2
PAPER EXIT SECTION
REGISTRATION SECTION
DRIVE SECTION 2
FRAME SECTION
ELECTRICAL SECTION 1
Other Option 1
SCANNER SECTION 2
Other Option 2
Duplex Section 1
DRIVE SECTION 3
ELECTRICAL SECTION 4
Controller Section
SCANNER SECTION 3
ELECTRICAL SECTION 5
Controller Option 1
Scanner Section 1
EXTERIOR 1
OPERATION PANEL
ELECTRICAL SECTION 3
ELECTRICAL SECTION 2
Duplex Section 3
LD Section
EXTERIOR 2
Paper Tray Section
Transfer/Separation Section
PCU SECTION
Duplex Section 2
Duplex Section 5
Paper Feed Section 1
Paper Inverter Section
EXTERIOR 3
Toner Supply Unit Section
Детали ELECTRICAL SECTION 1
| Деталь: | FUSING UNIT:NA:ASSY (for NA) |
| Парткод: | D1204001 |
| Деталь: | FUSING UNIT:EU:ASSY (for EU/AA/CHN/KOR) |
| Парткод: | D1204002 |
| Деталь: | FUSING UNIT:TWN:ASSY (for TWN) |
| Парткод: | D1204003 |
| Деталь: | FRAME:FUSING:UPPER:ASSY |
| Парткод: | D1204032 |
| Деталь: | DECAL:GRIP:GUIDE PLATE:FUSING EXIT |
| Парткод: | D1204181 |
| Деталь: | Spring:Open And Close:Guide |
| Парткод: | AA066418 |
| Деталь: | PICKOFF PAWL:FUSING |
| Парткод: | AE044025 |
| Деталь: | COMPRESSION SPRING:STRIPPER PAWLS |
| Парткод: | AA063697 |
| Деталь: | TENSION SPRING:PRESSURE:34.2N |
| Парткод: | AA066412 |
| Деталь: | Bracket:Stripper Pawls |
| Парткод: | D1204101 |
| Деталь: | HARNESS:DRAWER:FUSING:120V:NA (for NA/TWN) |
| Парткод: | D1205274 |
| Деталь: | HARNESS:DRAWER:FUSING:230V:EU (for EU/AA/CHN/KOR) |
| Парткод: | D1205275 |
| Деталь: | HEATER:120V:MAIN (for NA) |
| Парткод: | AX440352 |
| Деталь: | HEATER:230V:MAIN (for EU/AA/CHN/KOR) |
| Парткод: | AX440354 |
| Деталь: | HEATER:110V:MAIN (for TWN) |
| Парткод: | AX440356 |
| Деталь: | HEATER:120V:SUB (for NA) |
| Парткод: | AX440353 |
| Деталь: | HEATER:230V:SUB (for EU/AA/CHN/KOR) |
| Парткод: | AX440355 |
| Деталь: | HEATER:110V:SUB (for TWN) |
| Парткод: | AX440357 |
| Деталь: | Terminal:Heater |
| Парткод: | D1204090 |
| Деталь: | Gear:Hot Roller |
| Парткод: | AB011400 |
| Деталь: | BALL BEARING:30X42X7 |
| Парткод: | G0524618 |
| Деталь: | HOT ROLLER:DIA40:T0.4 |
| Парткод: | AE011128 |
| Деталь: | Pressure Roller:Mm27 |
| Парткод: | AE020161 |
| Деталь: | Spring:Flange:Pressure Roller |
| Парткод: | AA063698 |
| Деталь: | BALL BEARING:8*19*6 |
| Парткод: | AE030030 |
| Деталь: | KNOB SCREW:FIX:FUSING |
| Парткод: | D1204161 |
| Деталь: | Guide:Harness:Plate |
| Парткод: | D1204077 |
| Деталь: | STOPPER:EXTERNAL CIRCLIP |
| Парткод: | D1204071 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA143219 |
| Деталь: | DECAL:H-TEMP WARNING:SMALL |
| Парткод: | D1204184 |
| Деталь: | GUIDE:PAPER:RAIL:PCU |
| Парткод: | A2322374 |
| Деталь: | Manual Feed Table:Assy |
| Парткод: | D1822634 |
| Деталь: | Side Fence:Front |
| Парткод: | D1202747 |
| Деталь: | DECAL:SIDE FENCE:MANUAL FEED |
| Парткод: | D1202632 |
| Деталь: | Side Fence:Rear |
| Парткод: | D1202750 |
| Деталь: | BASE:MANUAL FEED TA BLE:ASSY |
| Парткод: | D1202744 |
| Деталь: | FRICTION PAD:10X50 |
| Парткод: | AF0 33008 |
| Деталь: | PAD:MANUAL FEED |
| Парткод: | B0392628 |
| Деталь: | DISC:SIDE FENCE |
| Парткод: | D0392752 |
| Деталь: | Rack:Side Fence:Rear |
| Парткод: | D0392751 |
| Деталь: | DECAL:SCALE:MANUAL FEED |
| Парткод: | D1202651 |
| Деталь: | COVER:PAPER:TRAILING EDGE |
| Парткод: | D1202638 |
| Деталь: | FEELER:PAPER:TRAILING EDGE |
| Парткод: | D0392737 |
| Деталь: | HARNESS CONNECTING MANUAL FEED UNITSENSOR |
| Парткод: | D1825358 |
| Деталь: | ROTARY SWITCH:PAPER SIZE SENSOR:AMP |
| Парткод: | AW500037 |
| Деталь: | LINK:MANUAL FEED TABLE |
| Парткод: | D1202696 |
| Деталь: | PHOTOINTERRUPTOR:LG2A 14NL1 |
| Парткод: | AW020198 |
| Деталь: | EXTENSION TRAY:MANUAL FEED |
| Парткод: | D1202740 |
| Деталь: | SPRING PLATE:EXTENSION TRAY |
| Парткод: | D0392779 |
| Деталь: | PIN:SIDE FENCE |
| Парткод: | D0392788 |
| Деталь: | SPRING:SIDE FENCE |
| Парткод: | D0392754 |
| Деталь: | GEAR:SIDE FENCE |
| Парткод: | D0392753 |
| Деталь: | SPRING:BASE:2.5N |
| Парткод: | D0392798 |
| Деталь: | Cover:Manual Feed Table |
| Парткод: | D1202736 |
| Деталь: | Rack:Side Fence:Front |
| Парткод: | D0392750 |
| Деталь: | DECAL:MANUAL FEED:INKJET:EXP |
| Парткод: | D1202631 |
| Деталь: | DECAL:MANUAL FEED:EXTENSION TRAY |
| Парткод: | D1202633 |
| Деталь: | TRANSPORT ROLLER:DUPLEX:EXIT |
| Парткод: | AF020754 |
| Деталь: | Link:Stopper |
| Парткод: | D1204677 |
| Деталь: | GEAR:TRANSPORT ROLLER |
| Парткод: | AB011295 |
| Деталь: | TORSION SPRING:STOPPER |
| Парткод: | AA066416 |
| Деталь: | ARM:STOPPER:PEEN |
| Парткод: | D1204673 |
| Деталь: | PLAIN SHAFT BEARING:MM6 |
| Парткод: | AA082118 |
| Деталь: | TORSION SPRING:STOPPER:CONTACT POINT |
| Парткод: | AA066410 |
| Деталь: | GEAR:IDLER:DUPLEX :EXIT |
| Парткод: | AB011296 |
| Деталь: | Timing Belt:40S2M120 |
| Парткод: | AA043323 |
| Деталь: | GROUND PLATE:STEPPER MOTOR |
| Парткод: | 82381762 |
| Деталь: | GEAR:STEPPER MOTOR |
| Парткод: | D0392781 |
| Деталь: | BRACKET:COVER: RIGHT:PEEN |
| Парткод: | D1204612 |
| Деталь: | DC STEPPER MOTOR:DUPLEX:SUB-ASSY |
| Парткод: | D1204671 |
| Деталь: | HARNESS:DUPLEX UNIT:MAIN |
| Парткод: | D1825352 |
| Деталь: | STEPPER MOTOR:TRANSPORT |
| Парткод: | AX050302 |
| Деталь: | HARNESS:MANUAL FEED UNIT:MAIN |
| Парткод: | D1825357 |
| Деталь: | SPACER:DUPLEX:CONTACT POINT:REAR |
| Парткод: | D1204609 |
| Деталь: | SPACER:DUPLEX:CONTACT POINT:FRONT |
| Парткод: | D1204610 |
| Деталь: | LINK:FRONT:DUPLEX :ASSY |
| Парткод: | D1204625 |
| Деталь: | PULLEY:TRANSPORT ROLLER |
| Парткод: | AB030848 |
| Деталь: | BRACKET:ARM:STOPPER |
| Парткод: | D1204655 |
| Деталь: | COVER:DRIVE :FUSING:PEEN |
| Парткод: | D1206105 |
| Деталь: | GEAR:EXI T:DRIVE |
| Парткод: | AB011567 |
| Деталь: | GEAR:FUSI NG:IDLER |
| Парткод: | AB011565 |
| Деталь: | HOLDER:REGISTRATION |
| Парткод: | D1201178 |
| Деталь: | BRACKET:DRIVE:FUSING:PEEN |
| Парткод: | D1201185 |
| Деталь: | HARNESS:AC:FUSING:NA (for NA/TWN) |
| Парткод: | D1825321 |
| Деталь: | HARNESS:AC:FUSING:EU (for EU/AA/CHNIKOR) |
| Парткод: | D1825322 |
| Деталь: | BRACKET:FUSING: SWIVEL:PEEN |
| Парткод: | D1201189 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA143301 |
| Деталь: | LEVER:DC SOLENOID:ASSY |
| Парткод: | D1201193 |
| Деталь: | SYNCHRONOUS BELT:FUSING:S3M:5X288 |
| Парткод: | AA043673 |
| Деталь: | PULLEY:FUSI NG:NO.2 |
| Парткод: | AB030856 |
| Деталь: | BRACKET:DRIVE:DRUM :ASSY |
| Парткод: | D1821027 |
| Деталь: | DC BRUSHLESS MOTOR:MAIN:30.7W |
| Парткод: | AX060402 |
| Деталь: | PULLEY:FUSI NG:NO.1 |
| Парткод: | AB030855 |
| Деталь: | GEAR:FUSING:N0.2 |
| Парткод: | AB010404 |
| Деталь: | BRACKET:ARM:FUSING/PAPER EXIT UNIT |
| Парткод: | D1206111 |
| Деталь: | GUIDE PLATE:FUSING UNIT:REAR |
| Парткод: | D1205613 |
| Деталь: | Lever:Lock:Pressure |
| Парткод: | D1204197 |
| Деталь: | SIDE PLATE:FUSING:FRONT |
| Парткод: | D1204121 |
| Деталь: | Lever:Pressure Release:Front:Assy |
| Парткод: | D1204171 |
| Деталь: | LEVER:PRESSURE ROLLER:FRONT:PEEN |
| Парткод: | D1204116 |
| Деталь: | GRIP:PRESSURE:CHANGE |
| Парткод: | D1204112 |
| Деталь: | Lever:Pressure Release:Rear:Assy |
| Парткод: | D1204191 |
| Деталь: | LEVER:PRESSURE ROLLER:REAR:PEEN |
| Парткод: | D1204117 |
| Деталь: | SHAFT:PRESSURE:CHANGE |
| Парткод: | AA140794 |
| Деталь: | ELECTRODE PLATE:THERMOSTAT:REAR |
| Парткод: | D1204093 |
| Деталь: | ELECTRODE PLATE:THERMOSTAT:CONNECTING |
| Парткод: | D1204092 |
| Деталь: | Thermostat:Assy |
| Парткод: | D1204095 |
| Деталь: | Housing:Thermostat |
| Парткод: | D1204094 |
| Деталь: | SHEET:PLATE:HARNESS |
| Парткод: | D1204079 |
| Деталь: | Fusing Cleaning Roller |
| Парткод: | AE042029 |
| Деталь: | PLAIN SHAFT BEARING:FUSING CLEANING ROLLER |
| Парткод: | AA082073 |
| Деталь: | COMPRESSION SPRING:FUSING CLEANING ROLLER:5N |
| Парткод: | AA063699 |
| Деталь: | SIDE PLATE:FUSING:REAR |
| Парткод: | D1204125 |
| Деталь: | Link:Release:Drive |
| Парткод: | D1204082 |
| Деталь: | Lever:Release:Drive |
| Парткод: | D1204083 |
| Деталь: | Spring:Release:Drive |
| Парткод: | AA066411 |
| Деталь: | Cover:Thermostat |
| Парткод: | D1204078 |
| Деталь: | Sheet:Thermostat |
| Парткод: | D1204080 |
| Деталь: | Frame:Fusing:Lower |
| Парткод: | D1204072 |
| Деталь: | DECAL:H-TEMP WARNING (for NA/TWN) |
| Парткод: | D1204183 |
| Деталь: | DECAL:H-TEMP WARNING:EU (for EU/AA/CHN/KOR) |
| Парткод: | D1204187 |
| Деталь: | GROUND PLATE:FUSING ENTRANCE GUIDE PLATE |
| Парткод: | D1204086 |
| Деталь: | FUSING ENTRANCE GUIDE PLATE:RIGHT |
| Парткод: | D1204085 |
| Деталь: | Thermistor:Fusing:Inner Back |
| Парткод: | AW100053 |
| Деталь: | Holder:Thermistor |
| Парткод: | D1204099 |
| Деталь: | SPACER:SAFETY SWITCH:FUSING UNIT |
| Парткод: | D1204076 |
| Деталь: | PLAIN SHAFT BEARING:FUSING |
| Парткод: | D1204208 |
| Деталь: | ELECTRODE PLATE:THERMOSTAT:FRONT |
| Парткод: | D1204091 |
| Деталь: | Decal:Exchange Indication:Envelope |
| Парткод: | D1204182 |
| Деталь: | Roller:Lever:Pressure |
| Парткод: | B2384194 |
| Деталь: | Screw:Drawer |
| Парткод: | AA143792 |
| Деталь: | FLANGED HEXAGO NAL HEAD BOLT HDD UNIT M3X3 |
| Парткод: | AA143848 |
| Деталь: | Bushing:HDD |
| Парткод: | AA161125 |
| Деталь: | SHEET:APPLICAllON: DOC:EU (DOC, for EU) |
| Парткод: | 1491549 |
| Деталь: | SHEET APPLI CATIONSCANNEREU (SCANNER, for EU) |
| Парткод: | 1491551 |
| Деталь: | SHEET APPL ICATIONPR INTER EU (PR INTER, for EU) |
| Парткод: | 1491552 |
| Деталь: | SHEET:APPLICAllON: DOC:NA (DOC, for AA) |
| Парткод: | 1491544 |
| Деталь: | SHEET APPLICATION SCANNER NA (SCANNER, for AA ) |
| Парткод: | 1491546 |
| Деталь: | SHEET APPLICATIONPR INTER NA (PR INTER, for AA) |
| Парткод: | 1491547 |
| Деталь: | SHEET:APPLICAllON: DOC:CHN (DOC,for CHN) |
| Парткод: | 1491564 |
| Деталь: | SHEETAPPLICATIONSCANNER CHN (SCANNER, f or CHN) |
| Парткод: | 1491566 |
| Деталь: | SHEET APPLICATION PRINTER CHN (PRINTER, for CHN) |
| Парткод: | 1491567 |
| Деталь: | SHEET:APPLICAllON: DOC:TWN (DOC , for TWN) |
| Парткод: | 1491569 |
| Деталь: | SHEETAP PLICATION:SCA NNERTWN (SCANNER, fo rTWN) |
| Парткод: | 1491571 |
| Деталь: | SHEET APFLI CATION PRINTERTWN (PRINTER, fa TWN) |
| Парткод: | 1491572 |
| Деталь: | CABLE:HDD:SATA:POWER_3P:70 |
| Парткод: | 1825260 |
| Деталь: | CABLE:HDD:SATA:RED 105:0RV-C2 |
| Парткод: | 1825261 |
| Деталь: | SD-CARD:PRT/SCN:ORV-C2 :EXP:ASSY |
| Парткод: | 1825524 |
| Деталь: | DECAL:PDF:l-GRAY:ABS |
| Парткод: | GA003268 |
| Деталь: | HOD :TOSHIBA:250GB :PHL |
| Парткод: | M1245765 |
| Деталь: | SD-CARD:P_ OPTION:ORV-C2: EXP:ASSY |
| Парткод: | 7575031 |
| Деталь: | SHEET:APPLICA llON:DOC:NA (for AA ) |
| Парткод: | 1491544 |
| Деталь: | SHEET:APPLICA llON:DOC:EU (for EU) |
| Парткод: | 1491549 |
| Деталь: | SHEET:APPLICAllON:DOC: CHN (for CHN) |
| Парткод: | 1491564 |
| Деталь: | SHEET:APPLICAllON: DOC:TWN (for TWN) |
| Парткод: | 1491569 |
| Деталь: | Paper Feed Unit:Assy |
| Парткод: | D1822700 |
| Деталь: | Feeler:Paper End |
| Парткод: | D0892767 |
| Деталь: | PHOTOINTERRUPTOR:LGRC102 |
| Парткод: | AW020204 |
| Деталь: | Harness:Paper Feed Unit |
| Парткод: | D1825353 |
| Деталь: | BRACKET:SENSOR:FEED |
| Парткод: | D0892778 |
| Деталь: | REFLECTION PHOTO SENSOR:KUA0055A |
| Парткод: | AW010128 |
| Деталь: | Bracket:Sensor |
| Парткод: | D0892781 |
| Деталь: | REFLECTION PHOTO SENSOR:PAPER FEED |
| Парткод: | AW010122 |
| Деталь: | DC Solenoid:Pickup:Assy |
| Парткод: | B2232780 |
| Деталь: | SPRING:RELEASE |
| Парткод: | AA062259 |
| Деталь: | Transport Roller:Drive |
| Парткод: | AF020764 |
| Деталь: | Bushing:DIA6 |
| Парткод: | AA082152 |
| Деталь: | SHEET:HARNESS:PAPER FEED UNIT |
| Парткод: | B2232772 |
| Деталь: | GROUND PLATE:FRONT |
| Парткод: | B2232786 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF030090 |
| Деталь: | GEAR:IDLER:PICKUP |
| Парткод: | AB011252 |
| Деталь: | EXTERNAL CIRCLIP:SEPARATE |
| Парткод: | AA100014 |
| Деталь: | GUIDE:FEED |
| Парткод: | D0892829 |
| Деталь: | Paper Feed Roller:Feed |
| Парткод: | AF031090 |
| Деталь: | GEAR:ROLLER CLUTCH |
| Парткод: | AB011218 |
| Деталь: | BUSHING:DIA6:DIA10:9 |
| Парткод: | AA082154 |
| Деталь: | GROUND PLATE:FEED |
| Парткод: | B2232765 |
| Деталь: | Arm:Pickup |
| Парткод: | D0892761 |
| Деталь: | SPRING:PRESSURE:PICKUP |
| Парткод: | AA060691 |
| Деталь: | LEVER:FEED |
| Парткод: | G0652767 |
| Деталь: | GEAR:FEED |
| Парткод: | D0892764 |
| Деталь: | SHAFT:FEED:ASSY |
| Парткод: | D1202762 |
| Деталь: | Paper Feed Roller:Separate |
| Парткод: | AF032090 |
| Деталь: | TORQUE LIMITER:40MNM:DIA18 |
| Парткод: | B0042783 |
| Деталь: | DISCHARGE BRUSH:PAPER FEED UNIT:UPPER |
| Парткод: | D1202618 |
| Деталь: | Gear:Separate:Driven |
| Парткод: | AB010157 |
| Деталь: | SPRING:PRESSURE:SEPARATE |
| Парткод: | AA060693 |
| Деталь: | LEVER:PRESSURE:SEPARATE |
| Парткод: | G0652774 |
| Деталь: | Gear:Separate:Drive |
| Парткод: | AB010156 |
| Деталь: | Shaft:Separate:Drive:Assy |
| Парткод: | B2232815 |
| Деталь: | GEAR:SEPARATOR:INPUT |
| Парткод: | D0892819 |
| Деталь: | Snap Ring |
| Парткод: | 52062686 |
| Деталь: | LEVER:PRESSURE RELEASE |
| Парткод: | G0652776 |
| Деталь: | LINK:RELEASE |
| Парткод: | G0652775 |
| Деталь: | Stay:Feed |
| Парткод: | B2232776 |
| Деталь: | SHAFT:SEPARATE:DRIVEN:ASSY |
| Парткод: | D1202810 |
| Деталь: | PLAIN SHAFT BEARING:MM6 |
| Парткод: | AA082118 |
| Деталь: | SPACER:EXIT |
| Парткод: | D1204456 |
| Деталь: | SHAFT:EXI T:EXI T |
| Парткод: | D1204479 |
| Деталь: | FEELER:EXIT:EXIT |
| Парткод: | D1204478 |
| Деталь: | BRACKET:DUPLEX:LOCK:REAR:ASSY |
| Парткод: | D1201099 |
| Деталь: | Discharge Brush:Exit |
| Парткод: | AA120146 |
| Деталь: | ROLLER:TENSI ON |
| Парткод: | AF040059 |
| Деталь: | SPRING PLATE:ROLLER:TENSION |
| Парткод: | D1204474 |
| Деталь: | ROLLER:TENSI ON:OUTER |
| Парткод: | AF040060 |
| Деталь: | SPRING PLATE:ROLLER:TENSION:OUTER |
| Парткод: | D1204483 |
| Деталь: | STOPPER:SPRING PLATE :OUTER |
| Парткод: | D1204486 |
| Деталь: | Stopper:Spring Plate |
| Парткод: | D1204487 |
| Деталь: | GUIDE PLATE:PAPER EXIT UNIT:LOWER |
| Парткод: | D1204452 |
| Деталь: | GROUND PLATE:PAPER EXIT UNIT |
| Парткод: | D1204454 |
| Деталь: | GEAR:EXIT ROLLER |
| Парткод: | AB011297 |
| Деталь: | EXIT ROLLER |
| Парткод: | AF020757 |
| Деталь: | FEELER:PAPER FEED SENSOR |
| Парткод: | D1204476 |
| Деталь: | GUIDE PLATE:PAPER EXIT UNIT:UPPER |
| Парткод: | D1204453 |
| Деталь: | Stay:Exit |
| Парткод: | D1204455 |
| Деталь: | PHOTOINTERRUPTOR:LG2A 14NL1 |
| Парткод: | AW020198 |
| Деталь: | BRACKET:DUPLEX:LOCK:FRONT:ASSY |
| Парткод: | D1201097 |
| Деталь: | COVER:EXIT:SENSOR |
| Парткод: | D1204489 |
| Деталь: | HARNESS:BCU:PAPER FEED SENSOR |
| Парткод: | D1205307 |
| Деталь: | Roller:Driven |
| Парткод: | AF022180 |
| Деталь: | PLAIN SHAFT BEARING:MM6 |
| Парткод: | AA082118 |
| Деталь: | BRACKET:DC FAN MOTOR:SIROCCO |
| Парткод: | D1201129 |
| Деталь: | CLEANER:REGISTRATION:ASSY |
| Парткод: | D1202755 |
| Деталь: | BRACKET:CLEANER:REGISTRA llON |
| Парткод: | D1202757 |
| Деталь: | REGISTRATION ROLLER:DRIVE:DIA 18.21:ASSY |
| Парткод: | AF020763 |
| Деталь: | Registration Roller:Driven:Assy |
| Парткод: | AF021087 |
| Деталь: | BRACKET:REGISTRATION GUIDE:REAR |
| Парткод: | D1202827 |
| Деталь: | BRACKET:REGISTRATION GUIDE:FRONT |
| Парткод: | D1202826 |
| Деталь: | KNOB:REGISTRATION ROLLER:ASSY |
| Парткод: | D1202819 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52152621 |
| Деталь: | PLAIN SHAFT BEARINGREGISTRATION ROLLERDRIVEN |
| Парткод: | D0192823 |
| Деталь: | PLAIN SHAFT BEARING:MM8 |
| Парткод: | AA082116 |
| Деталь: | TENSION SPRING:REGISTRATION:DRIVEN |
| Парткод: | D1202829 |
| Деталь: | GUIDE PLATE:REGISTRA TION:LEFT:AUXILIARY |
| Парткод: | D1202699 |
| Деталь: | Guide Plate:Registration:Right |
| Парткод: | D1202694 |
| Деталь: | HARNESS:CONNECTING:REGISTRATION SENSOR |
| Парткод: | D1825337 |
| Деталь: | REFLECTION PHOTO SENSOR:EXIT |
| Парткод: | GW010007 |
| Деталь: | BRACKET:REGISTRA llON SENSOR |
| Парткод: | D1202697 |
| Деталь: | GUIDE PLATE:REGISTRATION:LEFT:PEEN |
| Парткод: | D1202692 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | DISCHARGE LAMP:C1:ASSY |
| Парткод: | D1203452 |
| Деталь: | ELECTROMAGN ET IC CLUTCH REGISTRATION 0 .5NM |
| Парткод: | AX200325 |
| Деталь: | PULLEY:GEAR:ELECTROMAGNETIC CLUTCH:CONNECTIN G |
| Парткод: | AB030858 |
| Деталь: | PULLEY:REGISlRA Tl ON:TIGHTENER |
| Парткод: | 1201175 |
| Деталь: | BRACKET:ORIVE:TI GHTENER:PEEN |
| Парткод: | 1201172 |
| Деталь: | TENSION SPRING:ARM:COUPLING |
| Парткод: | B2384717 |
| Деталь: | PULLEY:TRANSPORT:N0.1 |
| Парткод: | AB030857 |
| Деталь: | GEAR:TRANSPORT:NO .2 |
| Парткод: | AB010406 |
| Деталь: | SYNCHRONOUS BELT:TRANSPORT:S3M:5X387 |
| Парткод: | AA043671 |
| Деталь: | ELECTROMAGNETIC CLUTCH:0.45N M:Z44 |
| Парткод: | AX200324 |
| Деталь: | PULLEY CONNECTING PAPER FEEDREGISTRATION |
| Парткод: | AB030859 |
| Деталь: | SYNCHRONOUS BELT:S2M:288 |
| Парткод: | AA043674 |
| Деталь: | GEAR:IOLER:PAPER FEEO:VERTICAL TRANSPORT |
| Парткод: | AB011568 |
| Деталь: | PULLEY:PAPER FEEO:N0.2 |
| Парткод: | AB030860 |
| Деталь: | BRACKET:PAPER FEEO:VERTICAL lRANSPORT |
| Парткод: | 1201170 |
| Деталь: | Screw:PCU |
| Парткод: | B2591131 |
| Деталь: | HARNESS:OEVELOPMENT:ORAWER |
| Парткод: | 1205344 |
| Деталь: | FEELER:PAPER SIZE SENSOR:INNER BACK |
| Парткод: | 1202723 |
| Деталь: | BRACKET:PAPER SIZE SENSOR:INNER BACK |
| Парткод: | 1202724 |
| Деталь: | PHOTOINTERRUPTOR:LGRC102 |
| Парткод: | AW020204 |
| Деталь: | PUSH SWITCH |
| Парткод: | G0205626 |
| Деталь: | HARNESS:CONNECTING:RIGHT:OOOR SWITCH |
| Парткод: | 1825338 |
| Деталь: | RECEPTACLE:CHARGE:ASSY |
| Парткод: | 1823461 |
| Деталь: | RECEPTACLETRANSFER SEPARATION UNITO-C2ASSY |
| Парткод: | 1823950 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | COVER:GRIP:LEFT |
| Парткод: | 1205625 |
| Деталь: | GRIP:LEFT |
| Парткод: | 1205624 |
| Деталь: | BRACKET:GRIP:LEFT REAR |
| Парткод: | 1201077 |
| Деталь: | FRAME:LENGlHWISE:RIGHT FRONT |
| Парткод: | 1201078 |
| Деталь: | FRAME:LENGlHWISE:RIGHT REAR |
| Парткод: | 1201079 |
| Деталь: | CAP:POSITIONING: SHORT |
| Парткод: | B2232714 |
| Деталь: | GUIDE:HARNESS:PAPER FEED:INNER BACK |
| Парткод: | 1202816 |
| Деталь: | CUSHI ON:SEPARA TE |
| Парткод: | AA161163 |
| Деталь: | Supporter:Right:Assy |
| Парткод: | B2232715 |
| Деталь: | HINGE:DOOR:FRONT:RIGHT |
| Парткод: | 1201386 |
| Деталь: | BRACKET:GRIP:FRONT: LEFT AND RIGHT |
| Парткод: | 1201082 |
| Деталь: | Rubber Foot:H5 |
| Парткод: | AH010009 |
| Деталь: | SUPPORTER:LEFT:ASSY |
| Парткод: | 1202710 |
| Деталь: | HINGE:DOOR:FRONT:LEFT |
| Парткод: | 1201387 |
| Деталь: | COVER:GRIP:RIGHT FRONT |
| Парткод: | 1205623 |
| Деталь: | GRIP:RIGHT FRONT:ASSY |
| Парткод: | 1205620 |
| Деталь: | BRACKET:COVER: REAR |
| Парткод: | 1205615 |
| Деталь: | BRACKET:LINK:MAIN:ASSY |
| Парткод: | 1205604 |
| Деталь: | FAN:MM60:NIDEC:K |
| Парткод: | AX640170 |
| Деталь: | SHADING PLATE:CTL |
| Парткод: | D1205875 |
| Деталь: | COVER:EMI:CTL |
| Парткод: | D1825852 |
| Деталь: | GROUND PLATE:SCANNER:STAY:UPPER REAR |
| Парткод: | D0391095 |
| Деталь: | FLAT SCREW:KN08 SCREW:M4X10 |
| Парткод: | AA143575 |
| Деталь: | STOPPER CASTER - 60KGF |
| Парткод: | AH012013 |
| Деталь: | CASTER - 60KGF |
| Парткод: | AH012014 |
| Деталь: | STAND :DIA 1OO:ASSY |
| Парткод: | 88271051 |
| Деталь: | POSITIONING PIN:MACHINE OR COPIER |
| Парткод: | 88271071 |
| Деталь: | 8RACKET:TA8LE:IC CARD |
| Парткод: | D5931264 |
| Деталь: | TA8LE:IC CARD:UPPER:ASSY |
| Парткод: | D5931270 |
| Деталь: | TA8LE:IC CARD:LOWER |
| Парткод: | D5931273 |
| Деталь: | HARNESS:KEY COUNTER |
| Парткод: | A6745404 |
| Деталь: | DUAL FACES TAPE:KEY COUNTER HOLDER |
| Парткод: | A6745811 |
| Деталь: | 8RACKET:KEY COUNTER HOLDER:ASSY |
| Парткод: | 84521055 |
| Деталь: | PLATE NUT:KEY COUNTER HOLDER |
| Парткод: | 84521063 |
| Деталь: | COVER:KEY COUNTER HOLDER |
| Парткод: | 84521260 |
| Деталь: | PC8:MK8:AP-C1 |
| Парткод: | 88705102 |
| Деталь: | HARNESS:I08:MK8 |
| Парткод: | 88705510 |
| Деталь: | CARRIAGE :NO.2:SUB-ASSY |
| Парткод: | 1491742 |
| Деталь: | MIRROR:N0.2:CONCAVE:ASSY |
| Парткод: | 1491756 |
| Деталь: | SPRING PLATE:MIRROR:N0.2 |
| Парткод: | G4042810 |
| Деталь: | MIRROR:N0.3:CONVEX:ASSY |
| Парткод: | 1491757 |
| Деталь: | PULLEY |
| Парткод: | 82381807 |
| Деталь: | GUIDE:FFC:CARRIAGE:N0.2 |
| Парткод: | 1491754 |
| Деталь: | COVER:FFC:CARRIAGE:NO .2 |
| Парткод: | 1491755 |
| Деталь: | CARRIAGE:N0.1 :ASSY |
| Парткод: | 1491730 |
| Деталь: | HARNESS:FFC:LED |
| Парткод: | 1495207 |
| Деталь: | GUIDE :HARNESS :LED-8 |
| Парткод: | 1491728 |
| Деталь: | ILLUMINATION UNIT:LE0.8:ASSY |
| Парткод: | 1491721 |
| Деталь: | MIRROR:N0.1 |
| Парткод: | AC030169 |
| Деталь: | CLAMP:MIRROR:NO .1 |
| Парткод: | M0261815 |
| Деталь: | CLAMP:DRIVE WERE |
| Парткод: | 1491726 |
| Деталь: | Guide:FFC |
| Парткод: | 1491693 |
| Деталь: | PLATE SEAL:APS:HARNESS |
| Парткод: | 1491694 |
| Деталь: | INNER COVER:PEEN |
| Парткод: | 1491780 |
| Деталь: | REFLECTOR:SCANNER |
| Парткод: | 1491731 |
| Деталь: | 8RACKET:DEHUMIDIFlER:HEATER |
| Парткод: | 1491835 |
| Деталь: | HEATER:120V:9W |
| Парткод: | 82291687 |
| Деталь: | HEATER:230V :9W |
| Парткод: | 82291688 |
| Деталь: | CUSHION:SPACER |
| Парткод: | D6867010 |
| Деталь: | Guide Plate:Connecting:Upper |
| Парткод: | D6867192 |
| Деталь: | GUIDE PLATE:CONNECTI NG:LOWER |
| Парткод: | 84082191 |
| Деталь: | CECAL:MISFEED REMOVAL:BINDYES:ORVAL (f or SR3150) |
| Парткод: | D6867821 |
| Деталь: | CECAL:MISFEED REMOVAL:BINDNO.ORVAL (for SR 3140) |
| Парткод: | D6877821 |
| Деталь: | COVER:RIGHT SIDEWAYS:UPPER |
| Парткод: | D6867022 |
| Деталь: | COVER:RIGHT SIDEWAYS:LOWER |
| Парткод: | D6867021 |
| Деталь: | BRACKET:COUPLING:GROUND PLATE :REAR:ASSY |
| Парткод: | D6861455 |
| Деталь: | GATE PAWL:LOWER |
| Парткод: | AF025045 |
| Деталь: | COIL SPRING:GATE PAWL:LOWER |
| Парткод: | AA066414 |
| Деталь: | ROLLER:TENSI ON:GATE |
| Парткод: | 83004566 |
| Деталь: | Screw:Mm5:2.5MM |
| Парткод: | GA143003 |
| Деталь: | PLAIN SHAFT BEARING- M4 |
| Парткод: | AA080156 |
| Деталь: | SHAFT:ROLLER:TENSION |
| Парткод: | AA145818 |
| Деталь: | GUIDE PLATE:OPEN AND CLOSE:GATE |
| Парткод: | D1204665 |
| Деталь: | INNER COVER:REAR |
| Парткод: | D1204628 |
| Деталь: | Inner Cover:Front |
| Парткод: | D1204629 |
| Деталь: | INNER COVER:GRIP:DUPLEX UNIT |
| Парткод: | D1204645 |
| Деталь: | Spring - Exit |
| Парткод: | 52054527 |
| Деталь: | GUIDE PLATE:GATE:ASSY |
| Парткод: | D1204674 |
| Деталь: | COVER:8ASE:RU88ER FOOT |
| Парткод: | 82381066 |
| Деталь: | GRIP:REAR RIGHT |
| Парткод: | 1205828 |
| Деталь: | 8RACKET:GRIP:SUPPORT |
| Парткод: | 1205834 |
| Деталь: | DC MOTOR:RISE:ASSY |
| Парткод: | AX040154 |
| Деталь: | COVER:ELECTRICAL COMPONENTS |
| Парткод: | 82232722 |
| Деталь: | COVER:TRAY:RIGHT |
| Парткод: | 1202541 |
| Деталь: | 8RACKET:PUSH SWITCH |
| Парткод: | 82232721 |
| Деталь: | Push Switch:Paper Size Sensor |
| Парткод: | AW500038 |
| Деталь: | COVER:TRAY:LEFT |
| Парткод: | 1202543 |
| Деталь: | COVER:8ASE:POSITIONING PIN |
| Парткод: | 82381089 |
| Деталь: | 8RACKET:BASE |
| Парткод: | 1201091 |
| Деталь: | COVER:8ASE:CONNECTOR |
| Парткод: | 82 381 088 |
| Деталь: | 8RACKET:CONNECTOR:BASE |
| Парткод: | 1201096 |
| Деталь: | CUSHION ELECTR OMAGNET IC CLUTCHPAPER FEED |
| Парткод: | 1202820 |
| Деталь: | DUCT:DC FAN MOTOR |
| Парткод: | 1201102 |
| Деталь: | DUCT:UPPER |
| Парткод: | 1201105 |
| Деталь: | DUCT:LOWER |
| Парткод: | 1201104 |
| Деталь: | HOLDER:DUCT |
| Парткод: | 1201108 |
| Деталь: | FAN:MM60:NIDEC:K |
| Парткод: | AX640170 |
| Деталь: | FAN:MM80 |
| Парткод: | GX645734 |
| Деталь: | GUIDE PLATE:DUCT:EXHAUST |
| Парткод: | 1201106 |
| Деталь: | HARNESS:ORV-C2:0PERATl ON SUB-UNI T:ASSY |
| Парткод: | 1825250 |
| Деталь: | PCB:CTL:ORV-C2_EXP:25CPM |
| Парткод: | 1825760 |
| Деталь: | PCB:CTL:ORV-C2_EXP:30CPM |
| Парткод: | 1825761 |
| Деталь: | PCB:CTL:ORV-C2 EXP:33CPM |
| Парткод: | 1825762 |
| Деталь: | RAIL:RIGHT:SMALL |
| Парткод: | 95899 |
| Деталь: | RAIL:LEFT:FAX CONTROL UNIT |
| Парткод: | 95891 |
| Деталь: | Panel:Interface |
| Парткод: | 1205869 |
| Деталь: | SO-CARO:PRT/SCN:ORV-C2 :EXP:ASSY (SP Model) |
| Парткод: | 1825524 |
| Деталь: | HOO:TOSHIBA:250GB (SP Model) |
| Парткод: | 1425765 |
| Деталь: | CABLE:HOO:SATA:POWER 3P:70 (SP Model) |
| Парткод: | 1825260 |
| Деталь: | CABLE:HOO:SATA:RE0_ 105:0RV-C2 (SP Model) |
| Парткод: | 1825261 |
| Деталь: | FLANGED HEXAGONAL HEAD SOLTHDD UNIT:M3X3 (SP Mooel) |
| Парткод: | AA143848 |
| Деталь: | BUSHING:HOO (SP Model) |
| Парткод: | AA161125 |
| Деталь: | PCB:OOR3-0IMM:512MB(32BIT):ASSY (Basic Model) |
| Парткод: | M1095245 |
| Деталь: | PCB:OOR3-0IMM:RC-A:1.5GB:ASSY (SP Model) |
| Парткод: | M1295245 |
| Деталь: | NVRAM: ZERO COUNTER |
| Парткод: | 1849590 |
| Деталь: | HARNESS:SIO:STM |
| Парткод: | D1595304 |
| Деталь: | DC STEPPER MOTOR:PRESS FIT |
| Парткод: | D1491703 |
| Деталь: | SYNCHRONOUS BELT:138ST1.5-4.0 |
| Парткод: | D1491706 |
| Деталь: | Pulley:Idler |
| Парткод: | 82381806 |
| Деталь: | ORIGINAL SENSOR:66MM:3.3V |
| Парткод: | AW010155 |
| Деталь: | INTERFACE CABLE:SCANNER:LVDS:ASSY |
| Парткод: | D1825221 |
| Деталь: | Lens:Holder:Assy |
| Парткод: | D1491771 |
| Деталь: | PCB:SIO |
| Парткод: | D1495138 |
| Деталь: | Harness:Sio:Scanner Unit |
| Парткод: | D1495206 |
| Деталь: | HARNESS:SIO:IMAGE PROCESSING UNIT |
| Парткод: | D1825205 |
| Деталь: | TIMING PULLEY:62 |
| Парткод: | D1491710 |
| Деталь: | DRIVE WERE:DIA1 |
| Парткод: | D1491714 |
| Деталь: | PULLEY:DRIVE WERE:REAR |
| Парткод: | D1491717 |
| Деталь: | PULLEY:PROTECTION |
| Парткод: | D0291749 |
| Деталь: | TENSION SPRING:TENSION:11.3N:30MM |
| Парткод: | D1491709 |
| Деталь: | PULLEY:DRIVE WERE:FRONT |
| Парткод: | D1491715 |
| Деталь: | SHAFT:SCANNER:DRJVE |
| Парткод: | D1491711 |
| Деталь: | PLAIN SHAFT BEARING:DIA8XDIA12X7 |
| Парткод: | AA082144 |
| Деталь: | BRACKET:DC STEPPER MOTOR |
| Парткод: | D1491705 |
| Деталь: | BRACKET:TENSION: FRONT |
| Парткод: | D1491719 |
| Деталь: | BRACKET:TENSION: REAR |
| Парткод: | D1491718 |
| Деталь: | BRACKET:SIO:PEEN |
| Парткод: | D1491812 |
| Деталь: | HARNESS:AC:FUSING:NA (for NA/TWN) |
| Парткод: | 1825321 |
| Деталь: | HARNESS:AC:FUSING:EU (for EU/AA/CHN) |
| Парткод: | 1825322 |
| Деталь: | Harness:AC:Inlet |
| Парткод: | 1825314 |
| Деталь: | HARNESS:PSU |
| Парткод: | 1825312 |
| Деталь: | HARNESS:BCU:DOOR SWITCH |
| Парткод: | 1825304 |
| Деталь: | Bracket:Micro Switch |
| Парткод: | 1205629 |
| Деталь: | COMPRESSION SPRJNG:DOOR SWITCH |
| Парткод: | AA063476 |
| Деталь: | Tension Spring:Door Switch |
| Парткод: | 1201095 |
| Деталь: | Lever:Door Switch:Assy |
| Парткод: | 1205602 |
| Деталь: | HARNESS POWER SUPPLY UNIT SOB SHORT CIRCUIT |
| Парткод: | 1825310 |
| Деталь: | Bracket:Power Supply Cord |
| Парткод: | 1205831 |
| Деталь: | Cover:Main Switch |
| Парткод: | 1821300 |
| Деталь: | PCB:DCSW:B-C1 :ASSY |
| Парткод: | 1795730 |
| Деталь: | Fan:MM60:24V |
| Парткод: | AX640208 |
| Деталь: | HARNESS:AC:HEATER:EXP |
| Парткод: | 1825319 |
| Деталь: | PIN:BRACKET:MICRO SWITCH |
| Парткод: | 1205733 |
| Деталь: | POWER SUPPLY UNIT:247W:DOM/NA:ORV-C1 |
| Парткод: | AZ230255 |
| Деталь: | POWER SUPPLY UNIT:247W:EU/AA/CHN:ORV-C1 |
| Парткод: | AZ230257 |
| Деталь: | BRACKET:MAI N SWITCH |
| Парткод: | 1825616 |
| Деталь: | Keytop:Main Switch |
| Парткод: | 1495883 |
| Деталь: | CHOKE COIL:B1215018 (for EU/AA/CHN/KOR) |
| Парткод: | 61215018 |
| Деталь: | HEATER:NA:ASSY |
| Парткод: | 1820076 |
| Деталь: | HEATER:EU:ASSY |
| Парткод: | 1820077 |
| Деталь: | SHEET:APPLICA llON:SCANNER:EU (for EU) |
| Парткод: | 1491551 |
| Деталь: | SHEET:APPLICA llON:SCANNER:NA (for AA) |
| Парткод: | 1491546 |
| Деталь: | SHEET:APPLICAllON: SCANNER:CHN (for CHN) |
| Парткод: | 1491566 |
| Деталь: | SHEET:APPLICAllON: SCANNER:lWN (for lWN) |
| Парткод: | 1491571 |
| Деталь: | SO-CARO:SCN:ORV-C2: EXP:ASSY |
| Парткод: | 7575041 |
| Деталь: | SO-CARO:PS3:0RV-C2 :EXP:ASSY |
| Парткод: | 7575051 |
| Деталь: | OECAL:PS3:1-GRAY |
| Парткод: | GA003264 |
| Деталь: | SO-CARO:NE1WARE:ORV-C2: EXP:ASSY |
| Парткод: | 7585031 |
| Деталь: | SO-CARO:MFP8ROWSER:ORV-C2: EXP:ASSY |
| Парткод: | 7585041 |
| Деталь: | SO-CARO:OCR:EXP :ASSY |
| Парткод: | 1665024 |
| Деталь: | PC8:00R3-0IMM:RC-A:1.5G8:ASSY |
| Парткод: | M1295245 |
| Деталь: | PC8:ML832 |
| Парткод: | 3775603 |
| Деталь: | PC8:1EEE1284:ASSY |
| Парткод: | 85955670 |
| Деталь: | MOOULE:8LUETOOTH:US8 |
| Парткод: | 5665400 |
| Деталь: | CO-ROM:8LUETOOTH:OI :EXP:ASSY |
| Парткод: | 5667002 |
| Деталь: | PC8:WLAN-PPEM1 :ASSY |
| Парткод: | 1645200 |
| Деталь: | VELCRO FASTENER:COVER:ANTENNA:250 |
| Парткод: | 3775698 |
| Деталь: | PC8:1Cl8-3 |
| Парткод: | 88295106 |
| Деталь: | 8RACKET:ICl8:ALEX |
| Парткод: | 88295810 |
| Деталь: | 8RACKET:ICl8:GRIFFIN-C1 |
| Парткод: | 1175913 |
| Деталь: | COVER:SHEET THROUGH:DOCUMENT FEEDER |
| Парткод: | D1491800 |
| Деталь: | EXPOSURE GLASS:DOCUMENT FEEDER:APPLY |
| Парткод: | D1471805 |
| Деталь: | Bracket:Scale:Left |
| Парткод: | D1491801 |
| Деталь: | PHOTOI NTERRUPTOR:FLAT:PICH2MM:M4 |
| Парткод: | AW020207 |
| Деталь: | SCALE LEFTOOMIEU ASSY (for EU AA KORfTW NICHN) |
| Парткод: | D1491792 |
| Деталь: | SCALE:LEFT:NA:ASSY (for NA) |
| Парткод: | D1491793 |
| Деталь: | PHOTOINTERRUPTOR: LG248NL1A |
| Парткод: | AW020214 |
| Деталь: | Shielding Plate:Home Position Sensor |
| Парткод: | G5701225 |
| Деталь: | Harness:Sio:Sensor |
| Парткод: | D1495202 |
| Деталь: | Scale:Rear:Printing |
| Парткод: | D1491795 |
| Деталь: | Exposure Glass |
| Парткод: | A2501752 |
| Деталь: | SCREW:M3:BLACK |
| Парткод: | AA143537 |
| Деталь: | SHEET:GAP:ASSY |
| Парткод: | D1471750 |
| Деталь: | SEAL:SHEET THROUGH:DOCUMENT FEEDER |
| Парткод: | D1491798 |
| Деталь: | HOLDER:EXPOSURE GLASS:SCANNER |
| Парткод: | D1491804 |
| Деталь: | HOLDER:EXPOSURE GLASS |
| Парткод: | D1491805 |
| Деталь: | BRACKET:DOCUMENT FEEDER:RIGHT |
| Парткод: | D1821815 |
| Деталь: | BRACKET:DOCUMENT FEEDER:LEFT |
| Парткод: | D1821816 |
| Деталь: | BRACKET:DOCUMENT FEEDER:CABLE |
| Парткод: | D1821818 |
| Деталь: | END FENCE:EXIT |
| Парткод: | D1201307 |
| Деталь: | COVER:PAPER EXIT SUB-UNIT:LOWER:UPPER |
| Парткод: | D1201341 |
| Деталь: | Cover:Paper Exit Sub-unit:Lower |
| Парткод: | D1201340 |
| Деталь: | TRAY:REVERSE |
| Парткод: | D1204818 |
| Деталь: | FRAME:REVERSE: UPPER |
| Парткод: | D1204821 |
| Деталь: | FRAME:REVERSE: LOWER |
| Парткод: | D1204831 |
| Деталь: | Cover:Front:Right Upper |
| Парткод: | D1201304 |
| Деталь: | COVER:FRONT:RIGHT LOWER |
| Парткод: | D1201306 |
| Деталь: | Cover:Front:Assy |
| Парткод: | D1201330 |
| Деталь: | MAGNET CATCH:44.1N:ASSY |
| Парткод: | AG070504 |
| Деталь: | Cover:Shield Glass |
| Парткод: | D1201322 |
| Деталь: | Cover:SD-Card |
| Парткод: | D1201321 |
| Деталь: | Magnet Catch:Door:Front |
| Парткод: | 80241264 |
| Деталь: | Door:Front |
| Парткод: | D1201264 |
| Деталь: | DECAL:MA IN SWITCH:OWSTANOOY.DO M:NA (for NNAAIKOR) |
| Парткод: | AA000277 |
| Деталь: | CECAL MAIN SWITCH ON/STA NDBY EU(for EUfTWNICHN) |
| Парткод: | AA000279 |
| Деталь: | COVER:MAIN SWITCH:C2 |
| Парткод: | D1201266 |
| Деталь: | Plate:Logotype:RIC |
| Парткод: | AA001564 |
| Деталь: | PLATE:LOGOTYPE:LAN |
| Парткод: | AA001565 |
| Деталь: | PLATE:LOGOTYPE:GES |
| Парткод: | AA001567 |
| Деталь: | SHAFT:HINGE |
| Парткод: | G0201332 |
| Деталь: | COVER:PAPER EXIT SUB-UNIT:BEHIND |
| Парткод: | D1201343 |
| Деталь: | SEAL:SHEET:SMC |
| Парткод: | D1825897 |
| Деталь: | DECAL:SIZE INDICATION:PAPER TRAY |
| Парткод: | M1252877 |
| Деталь: | SHEET:EXPOSURE GLASS |
| Парткод: | 80651374 |
| Деталь: | HOLDER:EXPOSURE GLASS:IG:ASSY |
| Парткод: | D1441396 |
| Деталь: | DECAL:CAUTION:INKJET:GB |
| Парткод: | D1494390B |
| Деталь: | OPERATION SUB-UNIT:OR-C2:NA:ASSY (for NA/AA/KOR) |
| Парткод: | D1821411 |
| Деталь: | OPERATION SUB-UNIT:OR-C2:EU:ASSY (for EU) |
| Парткод: | D1821412 |
| Деталь: | OPERATION SUB-UNIT:OR-C2:CHN:ASSY (for CHN) |
| Парткод: | D1821414 |
| Деталь: | OPERATION SUB-UNIT:OR-C2:TWN:ASSY (for TWN) |
| Парткод: | D1821415 |
| Деталь: | SHEET:KEYTOP:LEFT |
| Парткод: | D1291528 |
| Деталь: | TOUCH PANEL:WVGA-9:MV |
| Парткод: | D1491427 |
| Деталь: | CABLE:FFC:OP-L |
| Парткод: | D1491430 |
| Деталь: | CABLE:FFC:OP-R |
| Парткод: | D1491431 |
| Деталь: | HARNESS:POWER |
| Парткод: | D1491433 |
| Деталь: | CABLE:LCDC:USB |
| Парткод: | D1491434 |
| Деталь: | CABLE:USB |
| Парткод: | D1491435 |
| Деталь: | PCB:OP-L:ASSY |
| Парткод: | D1491478 |
| Деталь: | PCB:OP-R:ASSY |
| Парткод: | D1491494 |
| Деталь: | COVER:UPPER:SH:NA (for NA/AA/KOR) |
| Парткод: | D1491533 |
| Деталь: | COVER:UPPER:SH:EU:BA (for EU) |
| Парткод: | D1491589 |
| Деталь: | COVER:UPPER:SH:CHN (for CHN) |
| Парткод: | D1491555 |
| Деталь: | COVER:UPPER:SH:TWN (for TWN) |
| Парткод: | D1491557 |
| Деталь: | Lens:Front |
| Парткод: | D1491511 |
| Деталь: | COVER:REAR:LARGE |
| Парткод: | D1491512 |
| Деталь: | COVER:REAR:SMALL:LEFT |
| Парткод: | D1491513 |
| Деталь: | COVER:REAR:SMALL:MIDDLE |
| Парткод: | D1491514 |
| Деталь: | COVER:REAR:SMALL:RIGHT |
| Парткод: | D1491515 |
| Деталь: | SPACER:LCD:A |
| Парткод: | D1491530 |
| Деталь: | SPACER:LCD:B |
| Парткод: | D1491531 |
| Деталь: | SHEET:LOGO:RIC |
| Парткод: | D1491553 |
| Деталь: | SHEET:LOGO:LAN |
| Парткод: | D1201556 |
| Деталь: | SHEET:LOGO:GES |
| Парткод: | D1201557 |
| Деталь: | LCD:TFT:WVGA-9:LED:AUO |
| Парткод: | D1821425 |
| Деталь: | CABLE:FFC:LCD |
| Парткод: | D1821432 |
| Деталь: | PCB:LCDC:AR2FT:OR-C2:ASSY |
| Парткод: | D1821455 |
| Деталь: | KEYTOP:HOME |
| Парткод: | D1291508 |
| Деталь: | Keytop:Start |
| Парткод: | D1491504 |
| Деталь: | Keytop:Stop |
| Парткод: | D1491505 |
| Деталь: | KEYTOP:10KEY:EU (for EU/TWN/CHN) |
| Парткод: | D1491538 |
| Деталь: | KEYTOP:10KEY:AA (for NA/AA/KOR) |
| Парткод: | D1491539 |
| Деталь: | KEYTOP:RESET SWITCH |
| Парткод: | D1491508 |
| Деталь: | Keytop:Left |
| Парткод: | D1491510 |
| Деталь: | KEYTOP:POWER SOURCE:BA |
| Парткод: | D1491588 |
| Деталь: | HARNESS:ORV-C2:OPERATION SUB-UNIT:ASSY |
| Парткод: | D1825250 |
| Деталь: | SHEET:APPLICATION:MULTI-LANGUAGE:NA(for NA/AA/KOR) |
| Парткод: | D1491575 |
| Деталь: | SHEET:APPLICATION:MULTI-LANGUAGE:EU (for EU) |
| Парткод: | D1491576 |
| Деталь: | SHEET:APPLICATION:MULTI-LANGUAGE:CHN (for CHN) |
| Парткод: | D1491577 |
| Деталь: | SHEET:APPLICATION:MULTI-LANGUAGE:TWN (for TWN) |
| Парткод: | D1491578 |
| Деталь: | SHEET:APPLICATION:MULTI-LANGUAGE:BLANK |
| Парткод: | D1291568 |
| Деталь: | Power Pack:BCTD |
| Парткод: | AZ320176 |
| Деталь: | HARNESS:BCU:OISCHARGE LAMP |
| Парткод: | 1825305 |
| Деталь: | Spacer:Lock:KGLS-12RT |
| Парткод: | G0205871 |
| Деталь: | HARNESS:BCU:HVP |
| Парткод: | 1825317 |
| Деталь: | HARNESS:BCU:PAPER EXIT SECTION: 1BlN |
| Парткод: | 1825306 |
| Деталь: | HARNESS:HVP:B |
| Парткод: | 1825343 |
| Деталь: | PCB:BCU:ASSY |
| Парткод: | 1825122 |
| Деталь: | HARNESS:FFC:BCU:IMAGE PROCESSING UNIT |
| Парткод: | 1825315 |
| Деталь: | HARNESS:BCU:MAIN:LOWER |
| Парткод: | 1825330 |
| Деталь: | HARNESS:BCU:MOTOR:MAIN |
| Парткод: | 1825302 |
| Деталь: | HARNESS:AC:FUSING:NA (for NA/TWN) |
| Парткод: | 1825321 |
| Деталь: | HARNESS:AC:FUSING:EU (for EU/AA/CHN/KOR) |
| Парткод: | 1825322 |
| Деталь: | Bracket:Power Pack |
| Парткод: | 1205833 |
| Деталь: | HARNESS:ORV-C2:0PERATl ON SUB-UNI T:ASSY |
| Парткод: | 1825250 |
| Деталь: | RECEPTACLETRANSFER SEPAR ATION UNITO-C2ASSY |
| Парткод: | 1823950 |
| Деталь: | RECEPTACLE:CHARGE:ASSY |
| Парткод: | 1823461 |
| Деталь: | BRACKET:ORAWER |
| Парткод: | 82385891 |
| Деталь: | HARNESS:BCU:JOINT UNIT |
| Парткод: | 1825341 |
| Деталь: | HARNESS:BCU:IPU |
| Парткод: | 1825308 |
| Деталь: | PCB:IMAGE PROCESSING UNIT:ORVAL-C2 |
| Парткод: | 1825152 |
| Деталь: | GUIDE PLATE:VERTICAL TRANSPORT:LOWER |
| Парткод: | 1202956 |
| Деталь: | SHEET:GUIDE:VERTICAL TRANSPORT: LOWER |
| Парткод: | 1202958 |
| Деталь: | TRANSPORT BELT:DRIVEN:VERllCAL TRANSPORT |
| Парткод: | 292677 |
| Деталь: | PULLEY:DRIVEN:IDLER |
| Парткод: | 92574 |
| Деталь: | PULLEY:DRIVEN:VERTICAL TRANSPORT |
| Парткод: | 92573 |
| Деталь: | HOLDER:DRIVEN:VERTICAL TRANSPORT |
| Парткод: | 92571 |
| Деталь: | SHAFT:DRIVEN:IOLER |
| Парткод: | 92575 |
| Деталь: | SHAFT:DRIVEN:VERTI CAL TRANSPORT |
| Парткод: | 92576 |
| Деталь: | PLAIN SHAFT BEARING:MM4 |
| Парткод: | G0602652 |
| Деталь: | SPRING :PRESSURE :11N |
| Парткод: | B2232676 |
| Деталь: | GUIDE PLATE VERTICAL TRANSPORT DRIVEN UPPER |
| Парткод: | 1202957 |
| Деталь: | HOOK:STOPPER:REAR |
| Парткод: | 1204699 |
| Деталь: | TENSION SPRING:LEVER:DUPLEX |
| Парткод: | AA061105 |
| Деталь: | Shaft:Grip |
| Парткод: | 392998 |
| Деталь: | GRIP:COVER:RIGHT |
| Парткод: | 1202996 |
| Деталь: | HOOK:STOPPER:DUPLEX UNIT:FRONT |
| Парткод: | 392996 |
| Деталь: | TIMING BELT:S2M288 |
| Парткод: | AA043584 |
| Деталь: | Cover:Right |
| Парткод: | 1204618 |
| Деталь: | DECAL:COVER:RI GHT |
| Парткод: | 1204643 |
| Деталь: | OPTICAL WRITING UNIT:ASSY |
| Парткод: | D1821860 |
| Деталь: | BLOCK:POSITIONING PIN:OPTICAL WRITING UNIT |
| Парткод: | D1201928 |
| Деталь: | DC POLYGON MIRROR MOTOR |
| Парткод: | AX060403 |
| Деталь: | LASER DIODE UNIT:ORVAL-C1 :ASSY |
| Парткод: | D1201891 |
| Деталь: | HARNESS:LASER DIODE |
| Парткод: | D1825223 |
| Деталь: | Shield Glass |
| Парткод: | AC015052 |
| Деталь: | PCB:Sync Detector |
| Парткод: | D0095325 |
| Деталь: | Decal:LD |
| Парткод: | G0291980 |
| Деталь: | COVER:SCANNER:LEFT:UPPER |
| Парткод: | D1821285 |
| Деталь: | Cover:Scanner:Left |
| Парткод: | D1821284 |
| Деталь: | Cover:Paper Exit Sub-unit:Left |
| Парткод: | D1201301 |
| Деталь: | COVER:SCANNER:FRONT UPPER |
| Парткод: | D1821271 |
| Деталь: | COVER:SCANNER:FRONT LOWER |
| Парткод: | D1821272 |
| Деталь: | Cover:Front Right:Upper |
| Парткод: | D1821270 |
| Деталь: | COVER:OPERA11ON SUB-UNI T:UPPER |
| Парткод: | D1821273 |
| Деталь: | Cover:Scanner:Rear |
| Парткод: | D1821290 |
| Деталь: | COVER:SCANNER:RJGHT: UPPER |
| Парткод: | D1821288 |
| Деталь: | COVER:SCANNER:RJGHT |
| Парткод: | D1821287 |
| Деталь: | MODEL NAME PLATE:MP2553 |
| Парткод: | D1826800 |
| Деталь: | MODEL NAME PLATE:MP3053 |
| Парткод: | D1836800 |
| Деталь: | MODEL NAME PLATE:MP3353 |
| Парткод: | D1846800 |
| Деталь: | MODEL NAME PLATE:MP2553SP |
| Парткод: | D1826801 |
| Деталь: | MODEL NAME PLATE:MP3053SP |
| Парткод: | D1836801 |
| Деталь: | MODEL NAME PLATE:MP3353SP |
| Парткод: | D1846801 |
| Деталь: | MODEL NAME PLATE:DSM1525SP |
| Парткод: | D1826802 |
| Деталь: | MODEL NAME PLATE:DSM1530 |
| Парткод: | D1836802 |
| Деталь: | MODEL NAME PLATE:DSM1533 |
| Парткод: | D1846802 |
| Деталь: | SCREW:M3:BLACK |
| Парткод: | AA143537 |
| Деталь: | DECAL:CAUTION:ORJGINAL:ENGLISH |
| Парткод: | D1496766 |
| Деталь: | DECAL:CAUTION:ORJGINAL:CHINESE |
| Парткод: | D1496767 |
| Деталь: | DECAL:CAUTION:ORJGINAL:TAIWAN |
| Парткод: | D1496768 |
| Деталь: | COVER:OPERA11ON SUB-UNI T:LOWER |
| Парткод: | D1821274 |
| Деталь: | PAPER TRAY:NO.1:ASSY (for 1st tray) |
| Парткод: | D1202850 |
| Деталь: | PAPER TRAY:NO.2:ASSY (for 2nd tray) |
| Парткод: | D1202900 |
| Деталь: | TRAY BOTTOM PLATE:NO.1:ASSY (for 1st tray) |
| Парткод: | D1202940 |
| Деталь: | TRAY BOTTOM PLATE:ASSY (for 2nd tray) |
| Парткод: | D0892940 |
| Деталь: | PAD |
| Парткод: | AF033010 |
| Деталь: | END FENCE:ASSY |
| Парткод: | D1202832 |
| Деталь: | SIDE FENCE:FRONT:ASSY (for 1st tray) |
| Парткод: | D1202920 |
| Деталь: | SIDE FENCE:FRONT:ASSY (for 2nd tray) |
| Парткод: | D1202926 |
| Деталь: | Plate:Side Fence:Right |
| Парткод: | B2232935 |
| Деталь: | Plate:Side Fence |
| Парткод: | B2232934 |
| Деталь: | SPRING PLATE:STOPPER:FRONT |
| Парткод: | B0042923 |
| Деталь: | Lever:Stopper:Front |
| Парткод: | D1202924 |
| Деталь: | SIDE FENCE:REAR:ASSY (for 1st tray) |
| Парткод: | D1202930 |
| Деталь: | SIDE FENCE:REAR:ASSY (for 2nd tray) |
| Парткод: | D1202933 |
| Деталь: | SPRING PLATE:SIDE FENCE:POSITIONING |
| Парткод: | A2672857 |
| Деталь: | Stopper:Positioning |
| Парткод: | A2672859 |
| Деталь: | Lever:Stopper:Positioning |
| Парткод: | D1202864 |
| Деталь: | DECAL:SIDE FENCE:REAR |
| Парткод: | D1202875 |
| Деталь: | Tension Spring:Side Fence:Rear |
| Парткод: | AA061003 |
| Деталь: | Gear:16z |
| Парткод: | B2232936 |
| Деталь: | Lever:Rise |
| Парткод: | B2232918 |
| Деталь: | SHAFT:RISE:NO.1:ASSY |
| Парткод: | B2232865 |
| Деталь: | GROUND PLATE:PAPER TRAY:NO.2 |
| Парткод: | B2232919 |
| Деталь: | Roller:Paper Tray |
| Парткод: | A2322987 |
| Деталь: | LINK:PAPER SIZE SENSOR |
| Парткод: | B2232910 |
| Деталь: | SPACER |
| Парткод: | B2232911 |
| Деталь: | SHAFT:RELEASE:PAPER TRAY |
| Парткод: | D0292863 |
| Деталь: | Tension Spring:Grip |
| Парткод: | AA061014 |
| Деталь: | LEVER:RELEASE:PAPER TRAY:INNER |
| Парткод: | D1202862 |
| Деталь: | HOLDER:GRIP:PAPER TRAY |
| Парткод: | D1202861 |
| Деталь: | LEVER:RELEASE:PAPER TRAY:OUTER |
| Парткод: | B2232868 |
| Деталь: | Cover:Paper Tray |
| Парткод: | D1202946 |
| Деталь: | GRIP:PAPER TRAY |
| Парткод: | D1202860 |
| Деталь: | SEAL:TRAY:NO.1 |
| Парткод: | D0892849 |
| Деталь: | DECAL:PAPER SET DIRECTION:TRAY:LEFT |
| Парткод: | D1202870 |
| Деталь: | DECAL:PAPER TRAY:NO.1 (for 1st tray) |
| Парткод: | D1202872 |
| Деталь: | DECAL:PAPER TRAY:NO.2 (for 2nd tray) |
| Парткод: | D1202873 |
| Деталь: | PLAIN SHAFT BEAA ING:POSHIONINGTRANSFER/SEPARATION UNIT |
| Парткод: | D1203858 |
| Деталь: | TRANSFERJSEPARA TION UNIT:C1:ASSY |
| Парткод: | D1203830 |
| Деталь: | CLEANER:REGISTRATION:DRIVEN |
| Парткод: | D1203812 |
| Деталь: | Cover:Density Sensor |
| Парткод: | D1203905 |
| Деталь: | SHEET:DISCHARGE:TRANSFER:FRONT |
| Парткод: | AA150708 |
| Деталь: | PLAIN SHAFT BEARING:TRANSFER ROLLER:REAR |
| Парткод: | AA080391 |
| Деталь: | CO MPRESSION SPRINGPRESSURETRANSF ER/SEPARATION UNIT |
| Парткод: | D1203859 |
| Деталь: | COVER:TRANSFERJSEPARATION UNIT |
| Парткод: | D1203855 |
| Деталь: | TERMINAL:TRANSFER ROLLER |
| Парткод: | D1203861 |
| Деталь: | TERMINAL:SEPARATION |
| Парткод: | D1203862 |
| Деталь: | COMPRESSION SPRING PRESSURE TRANSFER ROLLER REAR |
| Парткод: | D1203912 |
| Деталь: | COVER:PRESSURE:TRANSFER UNIT |
| Парткод: | D1203866 |
| Деталь: | ROLLER:TRANSFER UNIT |
| Парткод: | D1203867 |
| Деталь: | COVER:HARNESS:DENSITY SENSOR |
| Парткод: | D1203908 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG070514 |
| Деталь: | HARNESS:CONNECTI NG:DENSITY SENSOR |
| Парткод: | D1825336 |
| Деталь: | DENSITY SENSOR:LASER DIODE:ASSY |
| Парткод: | 82593890 |
| Деталь: | COMPRESSIQ SPRING:PRESSURE:TRANSFER RCT.LERFRONT |
| Парткод: | D1203911 |
| Деталь: | LEVER:SHUTIER |
| Парткод: | D1203931 |
| Деталь: | BAND STOPPER:COVER :TR ANSFER SEPARATION UNIT |
| Парткод: | D1203941 |
| Деталь: | SHEET:DISCHARGE: TRANSFER:REAR |
| Парткод: | AA150709 |
| Деталь: | BUSHING:TRANSFER ROLLER:FRONT |
| Парткод: | AA080390 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | SHEET:REGISTRATION SENSOR:OPPOSED |
| Парткод: | D1202851 |
| Деталь: | PCU:EXP:ASSY |
| Парткод: | D1203000 |
| Деталь: | Pickoff Pawl |
| Парткод: | B0392335 |
| Деталь: | Drum Shutter |
| Парткод: | B0392343 |
| Деталь: | Clip - OPC DRUM |
| Парткод: | B0392350 |
| Деталь: | Blade:Cleaning |
| Парткод: | AD041114 |
| Деталь: | Gear - 13Z |
| Парткод: | AB011403 |
| Деталь: | Gear - 14Z |
| Парткод: | AB011402 |
| Деталь: | Roller:Charge:A3 |
| Парткод: | AD027018 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA143444 |
| Деталь: | Charge Cleaner Brush Roller |
| Парткод: | AD042058 |
| Деталь: | Charge Roller Spring |
| Парткод: | B0392287 |
| Деталь: | Front Pressure Arm - Charge Roller |
| Парткод: | B0392292 |
| Деталь: | Pin - Front Pressure Arm |
| Парткод: | B0392293 |
| Деталь: | Arm:Pressure:Charge:Rear |
| Парткод: | D1203174 |
| Деталь: | Electrode Plate:Roller:Charge:Assy |
| Парткод: | D1203175 |
| Деталь: | GEAR:IDLER:TONER RECYCLING |
| Парткод: | D1203183 |
| Деталь: | COVER:PCU:FRONT:ASSY |
| Парткод: | D1203180 |
| Деталь: | SHUTTER:PCU |
| Парткод: | D1203193 |
| Деталь: | COMPRESSION SPRING:SHUTTER:PCU |
| Парткод: | A2673194 |
| Деталь: | Drum Stay:Front:Assy |
| Парткод: | D1203210 |
| Деталь: | DRUM STAY:REAR:SUB-ASSY |
| Парткод: | D1203233 |
| Деталь: | Development Roller:Assy |
| Парткод: | D1203320 |
| Деталь: | Development Roller Gear |
| Парткод: | B0393060 |
| Деталь: | Idler Gear - 16z |
| Парткод: | B0393062 |
| Деталь: | Case:Development Roller:Assy |
| Парткод: | D1203360 |
| Деталь: | CASE:DEVELOPMENT:ASSY |
| Парткод: | D1203371 |
| Деталь: | Joint:Development |
| Парткод: | D1203440 |
| Деталь: | OPC Drum |
| Парткод: | B0399510 |
| Деталь: | Developer Type 28 Black |
| Парткод: | B1219640 |
| Деталь: | TRANSPORT ROLLER:DUPLEX:CONNECTI NG |
| Парткод: | AF020756 |
| Деталь: | TRANSPORT ROLLER:DUPLEX:ENTRANCE |
| Парткод: | AF020755 |
| Деталь: | DRIVEN ROLLER:DIA 16 |
| Парткод: | D0094664 |
| Деталь: | PLAIN SHAFT BEARING:PRESSURE:MM4 |
| Парткод: | AA080254 |
| Деталь: | COMPRESSION SPRING:ROLLER:DRIVEN |
| Парткод: | AA063475 |
| Деталь: | BRACKET:DUPLEX:EXIT SENSOR |
| Парткод: | D1204647 |
| Деталь: | PHOTOINTERRUPTOR:DUPLEX |
| Парткод: | AW020206 |
| Деталь: | SPRING PLATE:GUIDE PLATE:PRESSURE |
| Парткод: | D1204675 |
| Деталь: | GUIDE PLATE:DRIVEN |
| Парткод: | D1204613 |
| Деталь: | DRIVEN ROLLER:ENTRANCE :DUPLEX |
| Парткод: | D0394542 |
| Деталь: | PLAIN SHAFT BEARING:DIA4 |
| Парткод: | 82234552 |
| Деталь: | Tension Spring:Driven Roller |
| Парткод: | D0394597 |
| Деталь: | GUIDE PLATE:DUPLEX:ENTRANCE |
| Парткод: | D1204619 |
| Деталь: | HARNESS:DUPLEX UNIT:MAIN |
| Парткод: | D1825352 |
| Деталь: | ARM:PRESSURE RELEASE:DUPLEX:FRONT |
| Парткод: | D1204653 |
| Деталь: | ARM:PRESSURE RELEASE:DUPLEX:REAR |
| Парткод: | D1204664 |
| Деталь: | PULLEY:TRANSPORT ROLLER:ENTRANCE |
| Парткод: | AB030847 |
| Деталь: | TIMING BELT:S2M288 |
| Парткод: | AA043584 |
| Деталь: | DECAL:DUPLEX:OPEN AND CLOSE |
| Парткод: | D1204640 |
| Деталь: | STOPPER:GUIDE PLATE :DRIVEN |
| Парткод: | D1204614 |
| Деталь: | PLAIN SHAFT BEARING:MM6 |
| Парткод: | AA082118 |
| Деталь: | BUSHING:DIA6:DIA 10:9 |
| Парткод: | AA082154 |
| Деталь: | HARNESS:CONNECTING:DUPLEX UNIT:SENSOR |
| Парткод: | D1825351 |
| Деталь: | 8RACKET:PAPER END SENSOR:MANUAL FEED |
| Парткод: | D0392724 |
| Деталь: | FEELER:MANUAL FEED |
| Парткод: | D0392725 |
| Деталь: | PHOTOINTERRUPTOR:LG2A 14NL1 |
| Парткод: | AW020198 |
| Деталь: | TORSION SPRING:PAPER END SENSOR |
| Парткод: | D0392797 |
| Деталь: | SHAFT :CAM :ASSY |
| Парткод: | D0392796 |
| Деталь: | GUIDE PLATE:MANUAL FEED UNIT:UPPER |
| Парткод: | D1202626 |
| Деталь: | PLATE :HARNESS :MANUAL FEED |
| Парткод: | D0392763 |
| Деталь: | GEAR:CAM:RIGHT REAR |
| Парткод: | D0392789 |
| Деталь: | GEAR:ROLLER CLUTCH |
| Парткод: | D0392780 |
| Деталь: | SHEET:GUIDE PLATE:MANUAL FEED |
| Парткод: | D1202614 |
| Деталь: | Separation Pad:Assy |
| Парткод: | 82614650 |
| Деталь: | GEAR:CAM:RI GHT |
| Парткод: | D0392720 |
| Деталь: | GUIDE PLATE:MANUAL FEED UNIT:LOWER |
| Парткод: | D1202613 |
| Деталь: | HOLDER COMPR ESSION SPR ING SEPARATION PAD |
| Парткод: | D0392714 |
| Деталь: | LEVER:COMPRESSION SPRING:SEPARATION PAD |
| Парткод: | D0392711 |
| Деталь: | COMPRESSION SPRING:2.8N |
| Парткод: | 80434685 |
| Деталь: | SHAFT:DRIVE:MANUAL FEED UNIT |
| Парткод: | D0392786 |
| Деталь: | PAPER FEED ROLLER:MANUAL FEED |
| Парткод: | AF031060 |
| Деталь: | CAM:LEFT |
| Парткод: | D0392793 |
| Деталь: | GEAR:FEELER:LEFT |
| Парткод: | D0392790 |
| Деталь: | GEAR:CAM:LEFT REAR |
| Парткод: | D0392722 |
| Деталь: | 8RACKET:HOME POSITION SENSOR:PEEN |
| Парткод: | D1202612 |
| Деталь: | PLAIN SHAFT 8EARING:MM6 |
| Парткод: | AA082118 |
| Деталь: | RETAINING RINGS-C:DIA4 |
| Парткод: | D0392799 |
| Деталь: | COVER:HARNESS:UPPER |
| Парткод: | D1202847 |
| Деталь: | COVER:HARNESS:LOWER |
| Парткод: | D1202848 |
| Деталь: | Paper Feed Unit:Assy |
| Парткод: | D1822700 |
| Деталь: | GUIDE PLATE:SWIVEL:N0.2 |
| Парткод: | D1202963 |
| Деталь: | DISCHARGE BRUSH:PAPER FEED UNIT:UPPER |
| Парткод: | D1202618 |
| Деталь: | COVER:DUPLEX :LOWER |
| Парткод: | D1202967 |
| Деталь: | GUIDE PLATE:VERTICAL TRANSPORT:RJGHT |
| Парткод: | D1202962 |
| Деталь: | SPRJNG:COVER:MANUAL FEED |
| Парткод: | 82232665 |
| Деталь: | GUIDE PLATE:SWIVEL |
| Парткод: | D0092836 |
| Деталь: | GUIDE PLATE:VERTICAL TRANSPORT:LEFT |
| Парткод: | D1202961 |
| Деталь: | Bracket:Paper Feed Unit |
| Парткод: | D1201119 |
| Деталь: | BRACKET:COVER: FRONT |
| Парткод: | D1205698 |
| Деталь: | BRACKET:COVER: REAR |
| Парткод: | D1205699 |
| Деталь: | Reverse Unit:Assy |
| Парткод: | D1820221 |
| Деталь: | Reverse Roller |
| Парткод: | AF020758 |
| Деталь: | Ground Plate:Reverse Roller |
| Парткод: | D1204837 |
| Деталь: | FRAME:REVERSE ROLLER |
| Парткод: | D1204840 |
| Деталь: | GEAR:REVERSE ROLLER |
| Парткод: | AB011298 |
| Деталь: | TIMING PULLEY:19T:GEAR:Z24 |
| Парткод: | AB030853 |
| Деталь: | SYNCHRONOUS BELT:S3M:150 |
| Парткод: | AA043648 |
| Деталь: | COVER:MOTOR:REVERSE |
| Парткод: | D1204833 |
| Деталь: | GEAR:IDLER |
| Парткод: | AB010162 |
| Деталь: | PLAIN SHAFT BEARING:MM6 |
| Парткод: | AA082118 |
| Деталь: | Gear:Z31 |
| Парткод: | AB010161 |
| Деталь: | SEAL:REVERSE ROLLER |
| Парткод: | AA000273 |
| Деталь: | BRACKET:DC STEPPER MOTOR:PEEN |
| Парткод: | D1204810 |
| Деталь: | DC STEPPER MOTOR:9.5OHM |
| Парткод: | AX060401 |
| Деталь: | PULLEY:TRANSPORT ROLLER:REVERSE |
| Парткод: | AB030849 |
| Деталь: | TRANSPORT ROLLER:REVERSE |
| Парткод: | AF020759 |
| Деталь: | BRACKET:REFLECTION PHOTO SENSOR:REVERSE |
| Парткод: | D1204834 |
| Деталь: | REFLECTION PHOTO SENSOR:EXIT |
| Парткод: | GW010007 |
| Деталь: | HARNESS:REVERSE UNIT |
| Парткод: | D1825355 |
| Деталь: | Bracket:Dc Solenoid |
| Парткод: | D1204828 |
| Деталь: | FRAME:REVERSE |
| Парткод: | D1204830 |
| Деталь: | Reverse Roller:Driven |
| Парткод: | AF020778 |
| Деталь: | PLAIN SHAFT BEARING:DIA4 |
| Парткод: | AA080297 |
| Деталь: | COIL SPRING:REVERSE ROLLER:DRIVEN |
| Парткод: | AA063478 |
| Деталь: | LINK:GATE PAWL:LOWER |
| Парткод: | D1204829 |
| Деталь: | COIL SPRING:LINK:GATE PAWL:LOWER |
| Парткод: | AA066415 |
| Деталь: | DC SOLENOID:24V:2.9N |
| Парткод: | D1204827 |
| Деталь: | SIDE PLATE:REVERSE:REAR:ASSY |
| Парткод: | D1204811 |
| Деталь: | SIDE PLATE:REVERSE:FRONT:ASSY |
| Парткод: | D1204823 |
| Деталь: | FRAME:REVERSE:UPPER |
| Парткод: | D1204821 |
| Деталь: | FRAME:REVERSE:LOWER |
| Парткод: | D1204831 |
| Деталь: | Cover:Left |
| Парткод: | 1201280 |
| Деталь: | Cover:Rear:Upper |
| Парткод: | 1201291 |
| Деталь: | COVER:PAPER EXIT SUB-UNIT:RIGHT LOWER |
| Парткод: | 1201305 |
| Деталь: | COVER:PAPER EXIT SUB-UNIT:REAR |
| Парткод: | 1201300 |
| Деталь: | COVER:PAPER EXIT SUB-UNIT:INNER BACK |
| Парткод: | 1201309 |
| Деталь: | COVER:PAPER EXIT SUB-UNIT:REAR LOWER |
| Парткод: | 1201342 |
| Деталь: | Cover:Right Front |
| Парткод: | 1201272 |
| Деталь: | INNER COVER:GRIP:DUPLEX UNIT |
| Парткод: | 1204645 |
| Деталь: | Cover:Right |
| Парткод: | 1201270 |
| Деталь: | Cover:Right Rear |
| Парткод: | 1201271 |
| Деталь: | COVER:REAR:LOWER |
| Парткод: | 1201290 |
| Деталь: | COVER:LEFT REAR:BASIC (for BASIC) |
| Парткод: | 1821301 |
| Деталь: | COVER:LEFT REAR:SP (for SP) |
| Парткод: | 1821302 |
| Деталь: | CAP:COVER |
| Парткод: | 1201337 |
| Деталь: | CAP:COVER:REAR UPPER |
| Парткод: | 1201292 |
| Деталь: | TONER SUPPLY UNIT:CTYPE:ASSY |
| Парткод: | D1203503 |
| Деталь: | TONER SUPPLY UNIT:ORVAL-C1 :ATYPE |
| Парткод: | D8470170 |
| Деталь: | Cam:Handle |
| Парткод: | D1203606 |
| Деталь: | Shaft:Chuck |
| Парткод: | D1203572 |
| Деталь: | Shaft:Slide |
| Парткод: | A1843422 |
| Деталь: | SPRING :CHUCK:TONER BOTTLE |
| Парткод: | A2673556 |
| Деталь: | Slider:Assy |
| Парткод: | D1203573 |
| Деталь: | Chuck:Bottle |
| Парткод: | D1203571 |
| Деталь: | COVER:TONER BOTTLE:CTYPE:SUB-ASSY |
| Парткод: | D1203562 |
| Деталь: | SPACER:DC MOTOR:TONER BOTTLE |
| Парткод: | D1203620 |
| Деталь: | DC MOTOR:TONER BOTTLE:Z:R-C5.5:ASSY |
| Парткод: | D0853616 |
| Деталь: | BRACKET:DC MOTOR:TONER BOTTLE:Z:EXP |
| Парткод: | D1207440 |
| Деталь: | SEAL:REMOVERll NSTALL :PCU |
| Парткод: | A2671059 |
| Деталь: | CUSHION:REMOVE PAPER DUST:UPPER |
| Парткод: | D1202925 |
| Деталь: | Guide Plate:Toner Supply Unit:Assy |
| Парткод: | D1205608 |
Коды ошибок
SC101-01
SC101-02
SC102
SC120
SC121
SC141
SC142
SC144
SC161-01
SC165
SC195
SC202
SC203
SC204
SC220
SC230
SC231
SC240
SC270
SC302
SC355
SC389
SC390
SC391
SC392
SC401
SC402
SC411
SC490
SC500
SC501
SC502
SC503
SC504
SC508
SC530
SC531
SC532
SC541
SC542-01
SC542-03
SC543
SC544
SC545
SC547-01
SC547-02
SC547-03
SC547-04
SC551
SC552-01
SC552-03
SC553
SC554
SC555
SC557
SC559
SC620-01
SC620-02
SC621
SC622
SC632-00
SC633-00
SC634-00
SC635-00
SC636-01
SC636-02
SC636-11
SC637-01
SC637-02
SC650-01
SC650-04
SC650-05
SC650-13
SC650-14
SC651-01
SC651-02
SC652-00
SC653-00
SC669-01
SC669-02
SC669-03
SC669-04
SC669-05
SC669-06
SC669-07
SC669-08
SC669-09
SC669-10
SC669-11
SC669-12
SC669-13
SC669-14
SC669-15
SC669-16
SC669-17
SC669-18
SC669-19
SC669-20
SC669-21
SC669-22
SC669-23
SC669-24
SC669-25
SC669-26
SC669-36
SC670-00
SC672-10
SC672-11
SC672-12
SC672-13
SC672-99
SC687
SC701-03
SC701-08
SC702-01
SC702-02
SC702-03
SC721-03
SC721-10
SC721-11
SC721-17
SC721-24
SC721-25
SC721-27
SC721-28
SC721-30
SC721-33
SC721-41
SC721-42
SC721-44
SC721-52
SC721-53
SC721-58
SC721-59
SC721-70
SC721-71
SC721-80
SC770
SC791
SC792
SC793-01
SC793-02
SC793-03
SC793-04
SC793-05
SC793-06
SC793-07
SC793-08
SC793-09
SC793-11
SC793-12
SC794-01
SC794-02
SC794-03
SC794-04
SC794-05
SC794-06
SC794-07
SC794-08
SC794-09
SC794-10
SC794-11
SC794-12
SC816-01
SC816-02
SC816-03
SC816-04
SC816-05
SC816-07
SC816-08
SC816-09
SC816-10
SC816-11
SC816-12
SC816-13
SC816-14
SC816-15
SC816-19
SC816-20
SC816-22
SC816-23
SC816-24
SC816-25
SC816-26
SC816-29
SC816-35
SC816-36
SC841-00
SC842-00
SC842-01
SC842-02
SC853-00
SC854-00
SC855-01
SC855-02
SC857-00
SC858-01
SC858-02
SC858-30
SC858-31
SC859-01
SC859-02
SC859-10
SC860-00
SC865-00
SC866-00
SC867-00
SC868-00
SC868-01
SC868-02
SC870
SC872-00
SC873-00
SC875-01
SC875-02
SC876-01
SC876-02
SC876-03
SC876-04
SC876-05
SC876-99
SC877-00
SC880-00
SC881-01
SC899-00
SC900-00
SC901
SC920
SC921-00
SC925
SC990-00
SC991-00
SC992-00
SC995-01
SC995-02
SC995-03
SC995-04
SC997-00
SC998-00
Описание
| Error code: | SC101-01 |
| Description: | CIS Error: Front Side The peak white level is less than the prescribed value. |
| Causes: | • CIS is defective. • MPU is defective. • Power/signal harness is defective. • Scanner unit condensation • CIS is not set properly, or is dirty. • The white plate is not set properly, or is dirty. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Clean the white guide plate. 2. Reset/clean the CIS and white plate in the scanner. 3. Replace the units in the following order: • Original front side CIS • Engine board • PSU/Signal harness |
| Error code: | SC101-02 |
| Description: | Lamp Error (Detecting the lighting error) The white level peak did not reach the prescribed threshold when the white guide plate was scanned. Error detection timing; During the scanner adjustment (detecting the lighting error) at the time of applying power source for scanner (when the main power is turned ON). |
| Causes: | • Condensation in scanner unit • Connector disconnected • Scanner Carriage defective • BiCU defective • Harness defective • White Guide Plate dirty or attachment fault • IOB defective |
| Remedy: | Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Reconnect the connector. Reconnect the following connectors; • Scanner Carriage – BiCU connector • SBU – LEDB connector (SBU side connector on the scanner carriage) • BiCU – IOB harness 2. Check the white guide plate (exposure glass). Check the white guide plate attached to the exposure glass. If the white guide plate is in an unusual state, replace the white guide plate. 3. Scanner carriage defective Replace the scanner carriage. 4. BiCU defective Replace the BiCU. 5. Harness defective Replace the following harnesses. • Scanner Carriage – BiCU harness • BiCU – IOB harness 6. IOB defective Replace the IOB. |
| Error code: | SC102 |
| Description: | LED Illumination Adjustment Error The white level peak reached the prescribed threshold when the white plate was scanned after a specified number of adjustments. |
| Causes: | • LED defective • IDB (LED driver) defective • SBU defective • IPU defective • Power/signal harness defective |
| Remedy: | 1. Turn the power off/on. 2. Reconnect the power/signal harness. 3. Replace the following parts: • Replace the LED board. • Replace the SBU board. • Replace the IDB board or SIO board. • Replace the IPU board. • Replace the power/signal harness. |
| Error code: | SC120 |
| Description: | Scanner home position error 1 The scanner home position sensor did not detect the home position (did not go OFF) after the scanner moved forward 20 mm.. |
| Causes: | The scanner home position sensor does not detect the scanner leaving the home position. • Defective scanner home position sensor • Defective scanner home position sensor harness • Defective scanner motor driver • Defective scanner motor |
| Remedy: | • Scanner motor driver board defective • Scanner motor defective • Scanner HP sensor defective • Harness between scanner motor and scanner I/O board disconnected or broken. |
| Error code: | SC121 |
| Description: | Scanner home position error 2 The scanner home position sensor did not go ON after the scanner moved forward 1 mm and the feeler entered the HP sensor. |
| Causes: | The scanner home position sensor does not detect the scanner coming back to the home position. • Defective scanner home position sensor • Defective scanner home position sensor harness • Defective scanner motor driver • Defective scanner motor |
| Remedy: | • Scanner motor defective • Scanner HP sensor disconnected, defective |
| Error code: | SC141 |
| Description: | Black level detection error During AGC the value for black level was not within ±2 of the prescribed value. The copier can reproduce monochrome, but not color. |
| Causes: | The automatic adjustment has failed to correct the black level to the permissible range. • Defective SBU board • Defective harness |
| Remedy: | • SBU defective • Harness defective |
| Error code: | SC142 |
| Description: | White level detection error During AGC the value for white level was not within ±7 of the prescribed value. |
| Causes: | The automatic adjustment has failed to correct the white level to the permissible range. • Defective scanner drive • Defective optical section • Defective SBU board • Defective harness |
| Remedy: | • Exposure lamp defective • Harness disconnected, damaged • Dirty exposure glass, optics • Scanner motor, drive assembly defective • SBU board defective |
| Error code: | SC144 |
| Description: | SBU (Sensor Board Unit) communication error When the machine is switched ON, or when the machine returns to full operation from the energy save mode, the machine can not access the SBU register, or the SBU register values are abnormal. |
| Causes: | Cannot correctly establish communication with the SBU. • Defective harness • Defective destination device (e.g., BICU, etc) • Defective SBU |
| Remedy: | • Dirty exposure glass or optics • SBU board defective • SBU harness disconnected, defective |
| Error code: | SC161-01 |
| Description: | IPU error (LSYNC error) |
| Causes: | When turning the power on or when recovering from energy saving mode, the machine performs a BICU self-diagnostic test. If it detects an error, it reports an IPU (LSUNC) error. • Defective IPU or BICU (or bad connection between the ASIC and the LEO, LSYNC Abnormal, etc) • Faulty cable connection between the SBU and IPU (or BICU). |
| Remedy: | • Check the connection between SBU and IPU (BICU) • Replace the IPU (BICU) |
| Error code: | SC165 |
| Description: | Unauthorized copy protection failed |
| Causes: | • The machine detects that the optional ICIB is not installed or is faulty even if "Unauthorized Copy Protection" in User Tools is enabled. • When the machine is switched on or recovers from the evergy saver mode, it detects that the installed optional ICIB is faulty. • ICIB nlot attached correctly • Defective ICIB |
| Remedy: | • Connect the ICIB correctly • Replace the ICIB |
| Error code: | SC195 |
| Description: | Machine serial number error The number registered for the machine serial number does not match. |
| Causes: | Comparison of the product identification code in the machine serial number (11 digits). The product identification code in the machine serial number (11 digits) does not match. |
| Remedy: | • Confirm the correct serial number of the machine in the specifications Important! WHEN SC195 OCCURS, THE SERIAL NUMBER MUST BE INPUT. PLEASE CONTACT YOUR TECHNICAL SUPERVISOR. |
| Error code: | SC202 |
| Description: | Polygon motor error 1: ON timeout The polygon mirror motor does not reach the targeted operating speed: • Within 10 seconds after turning ON. • Within 10 sec. after changing speed |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective • Polygon motor defective. |
| Error code: | SC203 |
| Description: | Polygon motor error 2: OFF timeout The polygon mirror motor does leave the READY status within 10 seconds after the polygon motor switches OFF. |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective • Polygon motor defective. |
| Error code: | SC204 |
| Description: | Polygon motor error 3: Polygon motor lock signal error The polygon motor lock signal goes HIGH (inactive) while the laser diode is firing. |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective |
| Error code: | SC220 |
| Description: | Laser Synchronization Detector Error 1: K Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 black, or leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) on the BICU is defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC230 |
| Description: | FGATE error 1: Feedback remains HIGH for K write After the start of timing to create the black image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU and LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC231 |
| Description: | FGATE error 1: Feedback remains LOW for K write After the start of timing to create the black image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC240 |
| Description: | LD error 1: K An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD. |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC270 |
| Description: | Mirror motor upper/lower limit: Y (Yellow) The pulse rate of the mirror motor reaches the upper or lower limit. Note: SP2182 displays the pulse rate for each motor. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK laser unit defective |
| Remedy: | • 3rd mirror motor is defective. • 3rd mirror motor connecter is not connected correctly. |
| Error code: | SC302 |
| Description: | AC charge output error 3: C An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | This SC is issued if the BICU detects a short in the power pack 10 times consecutively. Open circuit (+) / Short circuit (-) |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC355 |
| Description: | Toner Supply Error (K) • Amount of toner on the ID sensor pattern printed and read between sheets less than 0.100 (SP3300-1). • Accumulated toner clutch ON time in the K sub hopper of the toner supply unit greater than 5000 (SP3301-41) |
| Causes: | A small rectangular wire attached to the shaft of an augur in each toner supply unit scrapes the surface of the toner end sensor with each rotation of the augur. The cleaning wire may be bent or the toner end sensor is defective. If the toner end sensor is damaged or out of position, the toner end sensor will cease to function normally. |
| Remedy: | • Replace the affected toner supply unit. |
| Error code: | SC389 |
| Description: | TD sensor error 1 TD sensor output was less than 0.5V, or more than 0.5V 10 times in succession. If the fax unit is installed, this SC is issued immediately. If the fax unit is not installed, this SC is issued after the prescribed number of copies has printed. |
| Causes: | • TD sensor abnormal • Poor connection of the TD sensor harness |
| Remedy: | • Replace the TD sensor. • Replace the harness of the TD sensor. |
| Error code: | SC390 |
| Description: | TD sensor error 2 The TD sensor outputs less than 0.5V or more than 4.0V 10 times consecutively during copying. Note: If the fax option is installed, this SC is issued immediately. If the fax option is not installed, this SC is issued after the prescribed number of pages is copied. |
| Causes: | • TD sensor abnormal • Poor connection of the TD sensor harness |
| Remedy: | • Replace the TD sensor. • Replace the harness of the TD sensor. |
| Error code: | SC391 |
| Description: | Development bias leak The PWM output level was detected higher than 50% after 10 consecutive samplings. |
| Causes: | • high voltage power supply board defective • High voltage power supply board (power pack) harness loose, broken. • PCU connection loose or broken |
| Remedy: | • Cycle the main power off/on • Replace the harness of the high voltage power supply board (power pack). • Replace the PCU. |
| Error code: | SC392 |
| Description: | Development bias error The PWM duty level was detected higher than 5% within 100 ms after high voltage output started, and the feedback voltage was detected less than 0.3 V for more than 200 ms. |
| Causes: | • Harness connection between CGB power pack and IOB loose, broken, defective • CGB power defective • High voltage cable damaged |
| Error code: | SC401 |
| Description: | ID sensor error 2: Vsg When the ID sensor was calibrated, Vsg (reflectivity of the bare drum surface) was detected less than 2.5V after two attempts. -or- After calibration, Vsg was detected as 5.0V at PWM adjustment and PWM=0. |
| Causes: | • Dirty ID sensor • ID sensor harness connection loose, broken, defective • TD power pack defective • IOB defective |
| Error code: | SC402 |
| Description: | ID sensor error 3: Vsp The Vsp (reflectivity of ID sensor pattern) value was detected at "0" or more than 2.5V when the ID sensor was calibrated during process control. |
| Causes: | • OPC drum gear Allen screw loose • ID sensor dirty • ID sensor harness loose, broken, defective • ID sensor defective • IOB defective • Exposure unit defective • Development unit defective • TD power pack defective |
| Error code: | SC411 |
| Description: | ID sensor error 3: Development γ M Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC490 |
| Description: | Peltier Unit error The Abnormal Condition signal or the Peltier Unit is received 10 times. |
| Causes: | • No ITB unit in the machine • Dirty TM sensor |
| Remedy: | • Peltier Unit is defective |
| Error code: | SC500 |
| Description: | Transport/Fusing Motor Error The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Causes: | • Disconnected or defective motor harness. • Motor slips due to excessive load |
| Remedy: | 1. Check the harness from the transport/fusing motor. Replace it if necessary. |
| Error code: | SC501 |
| Description: | Tray 1 (tandem tray) feed error (Japan Only) • The tray 1 lift sensor does not switch ON 10 s after the tray lift motor switches ON and starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. • The lower limit sensor of the tandem tray does not detect the lower limit within 10 sec. |
| Causes: | • Tray lift motor harness disconnected, loose, defective • Paper or other obstacle trapped between tray and motor • Tray lift sensor disconnected, damaged • Lower limit sensor disconnected, damaged • Pick-up solenoid disconnected, blocked by an obstacle |
| Remedy: | • Tray lift motor harness disconnected, loose, defective • Paper or other obstacle trapped between tray and motor • Tray lift sensor disconnected, damaged • Lower limit sensor disconnected, damaged • Pick-up solenoid disconnected, blocked by an obstacle |
| Error code: | SC502 |
| Description: | Tray 2 (paper cassette) feed error (Japan Only) • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. • The lower limit sensor of the tandem tray does not detect the lower limit within 10 sec. |
| Causes: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Remedy: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Error code: | SC503 |
| Description: | Tray 1 feed error • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. |
| Causes: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Remedy: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Error code: | SC504 |
| Description: | Tray 2 feed error • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. |
| Causes: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Remedy: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Error code: | SC508 |
| Description: | By-pass bottom plate error The signal from the by-pass tray HP sensor does not change for 1.0 second after the by-pass motor has rotated counterclockwise. If this condition occurs three consecutive times, the SC is generated. |
| Causes: | • Disconnect or defective harness of the by-pass motor • Defective or disconnected connection for the by-pass motor. • Defective by-pass motor • Disconnect or defective harness of the by-pass HP sensor • Defective or disconnected connection for the by-pass HP sensor. • Defective by-pass HP sensor |
| Remedy: | • Check the cable connections. • Check and/or replace the defective component. • Replace the BCU. • Cycle the main power off/on |
| Error code: | SC530 |
| Description: | Fan error 1: fusing cooling fan motor. The BICU does not receive the lock signal 5 seconds after the fusing unit fan switches ON. |
| Causes: | • Disconnected or defective motor harness. • Defective LSU fan motor |
| Remedy: | • Fusing cooling fan disconnected, defective • BICU defective |
| Error code: | SC531 |
| Description: | Fan error 2: fusing cooling fan motor. The lock signal remained HIGH for 5 sec. while the fan at the front of the fusing unit near the heat dissipation fins was operating. |
| Causes: | • Disconnected or defective motor harness. • Defective LSU fan motor |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC532 |
| Description: | Fan error 3: PCB box fan. The lock signal remained HIGH for 5 sec. while the fan that cools the printed circuit boards was operating. |
| Causes: | • Disconnected or defective motor harness. • Defective air intake fan motor |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC541 |
| Description: | Heating roller thermistor 1 error 1: Poor connection. The temperature measured by the heating roller thermistor does not reach 130°C after 10 tries and 65 sec. have elapsed. |
| Causes: | • Disconnected thermistor • Defective harness connection |
| Remedy: | • Heating roller thermistor harness connection loose, disconnected, defective • Defective heating roller thermistor |
| Error code: | SC542-01 |
| Description: | Fusing lamp (Center) thermistor not reloaded 1 The heater thermistor has increased by less than 2.0 degrees in 1.5 seconds 5 times in a row. |
| Causes: | • Deformed or floating thermistor • Input voltage out of range |
| Remedy: | Clear the SP: fusing SC. |
| Error code: | SC542-03 |
| Description: | Fusing lamp (Center) thermopile not reloaded 2 The heater (Center) thermistor does not reach the reload temperature 17 seconds after the start of motor rotation. |
| Causes: | • Stained thermopile lens • Broken heater wire • Input voltage out of range • The overtemperature prevention mechanism started working |
| Remedy: | • Clean the thermopile lens. • Replace the thermopile. • Replace the Fusing Unit. • Clear the SP: fusing SC. |
| Error code: | SC543 |
| Description: | Heating roller thermistor 1 error 3: Software - High temperature. The thermistor detected a temperature over 230°C. |
| Causes: | • Defective I/O control (EGB) • Defective EGB |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature out of control Do SP5810 to cancel the SC fusing code. |
| Error code: | SC544 |
| Description: | Heating roller thermistor 1 error 4: Hardware - High temperature. The thermistor detected a temperature over 260°C. |
| Causes: | The machine detected the CPU port LOW twice at 100 ms intervals and issued this SC. This check is always done to check for overheating, even if SC543 does not detect the problem. |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC545 |
| Description: | Heating roller thermistor 1 error 5: Lamp remains ON. After hot roller reaches warmup temperature, the fusing lamps remained ON at full capacity for 25 sec. after reaching the warmup temperature while the hot roller was not rotating. |
| Causes: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken |
| Error code: | SC547-01 |
| Description: | Zero cross error (relay-contact soldering) Zero-cross signal is detected while the fusing relay is OFF. |
| Causes: | • Fusing relay defective (contact soldering) • Fusing relay drive circuit error |
| Remedy: | 1. Reconnect the connectors between PSU (AC Controller Board) and Paper Transport IOB. 2. Replace the PSU (AC Controller Board). 3. Replace the Paper Transport IOB. |
| Error code: | SC547-02 |
| Description: | Zero cross error (relay contact error) Zero-cross signal is not detected while the fusing relay is ON. |
| Causes: | • Fusing relay damage (contact open) • Fusing relay drive circuit error • PSU fuse (24VS) blowout |
| Remedy: | 1. Reconnect the connectors between PSU (AC Controller Board) and Paper Transport IOB. 2. Replace the PSU (AC Controller Board). 3. Replace the Paper Transport IOB. 4. Replace the harness between PSU (AC Controller Board) and Paper Transport IOB. |
| Error code: | SC547-03 |
| Description: | Zero cross error (low-frequency error) Mains power supply frequency is determined to be 44 Hz or lower. |
| Causes: | Frequency instability of mains power supply |
| Remedy: | 1. Check that the mains power supply frequency is higher than 44 Hz. If it is equal to or lower than 44 Hz, the mains power supply infrastructure may have defects to be dealt with. 2. Replace the PSU (AC Controller Board). |
| Error code: | SC547-04 |
| Description: | AC drive board: Not connected After the interlock door is fixed to close, AC drive board: connection detecting signal (CNCON) is not detected. |
| Causes: | • Poor connection of the AC drive board connector • Poor connection of the IOB connector • Harness broken between the AC drive board and the IOB • Poor connection detecting circuit of the AC drive board on the IOB |
| Remedy: | • Turn the main power off/on. • Reconnect the harness (check the connection of CN403 on the AC drive board to CN218 on the IOB). • Replace the AC drive board. • Replace the IOB. |
| Error code: | SC551 |
| Description: | Pressure roller thermistor error 1. The temperature measured by the pressure roller thermistor does not reach 0°C for 200 sec. |
| Causes: | In the condition of relay ON, the end thermistor on the fusing detects less than 0 degrees Celsius for more than 5 seconds. |
| Remedy: | • Loose connection of the pressure roller thermistor • Defective pressure roller thermistor • Defective BICU Do SP5810 to cancel the SC fusing code. |
| Error code: | SC552-01 |
| Description: | Fusing reload temperature error 1: Fusing temperature sensor: end |
| Causes: | Fusing temperature did not reach 80°C within 60 sec. after the start of fusing temperature control. |
| Remedy: | • Fusing lamp disconnected • Overheat prevention disconnect |
| Error code: | SC552-03 |
| Description: | Fusing (End) thermistor not reloaded The heating (End) thermistor does not reach 60 deg C 12.5 seconds after the start of motor rotation. |
| Causes: | • Deformed or floating thermistor • Broken heater wire • Input voltage out of range • The overtemperature prevention mechanism started working |
| Remedy: | • Clear the SP: fusing SC. • Replace the fusing (End) thermistor. • Replace the Fusing Unit. |
| Error code: | SC553 |
| Description: | Pressure roller thermistor error 3: Software -High temperature. The thermistor detected a temperature over 220°C. |
| Causes: | • Defective main board • Defective PSU |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC554 |
| Description: | Pressure roller thermistor error 4: Hardware - High temperature. The thermistor detected a temperature over 230°C. |
| Causes: | • Defective main board • Defective PSU • Defective fusing unit |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC555 |
| Description: | Pressure roller thermistor error 5: Lamp remains ON. After hot roller reaches warmup temperature, the pressure roller fusing lamp remains for 6 sec. while the hot roller is not rotating. |
| Causes: | The fusing lamp reached the warm-up temperature and then attained fusing temperature (full power), but remained on after paper passed through the fusing unit (hot roller was not rotating). |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken Do SP5810 to cancel the SC fusing code. |
| Error code: | SC557 |
| Description: | Zero Cross Frequency Error The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Causes: | • Defective fusing lamp relay • Unstable input power source |
| Remedy: | 1. Check the power supply source. 2. Replace the fusing unit. |
| Error code: | SC559 |
| Description: | Consecutive Fusing Jam The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Fuser SC Detect" in the SP Mode 2 tab. |
| Causes: | • Defective fusing unit • Defective fusing control |
| Remedy: | 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. |
| Error code: | SC620-01 |
| Description: | ADF Communication error 1 (DF3090 (D779)/ DF3100 (D3B0)) After ADF connection was recognized on startup, an error is detected. (disconnection detection) |
| Causes: | • ADF connection error • ADF defection • IPU board defection • Noise contamination |
| Remedy: | Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Check if all connectors related to SPDF/ARDF are connected securely. Reconnect the connectors if they are disconnected, or loose. 2. Check the machine and ADF firmware version. • Proceed to Step 3 if there is no new firmware released. • Run the firmware update when there is a new firmware released. 3. Check the harness. Replace the harness if it is disconnected, or damaged. 4. Replace the IPU. 5. Check if there are any signs of a short circuit on the SPDF/ARDF Main Board. If there are any defects, replace the board. |
| Error code: | SC620-02 |
| Description: | ADF Communication error 2 (DF3090 (D779)/ DF3100 (D3B0)) After ADF connection was recognized on startup, an error is detected. (Retry out due to communication error) |
| Causes: | • ADF connection error • ADF defection • IPU board defection • Noise contamination |
| Remedy: | Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Check if all connectors related to SPDF/ARDF are connected securely. Reconnect the connectors if they are disconnected, or loose. 2. Check the machine and ADF firmware version. • Proceed to Step 3 if there is no new firmware released. • Run the firmware update when there is a new firmware released. 3. Check the harness. Replace the harness if it is disconnected, or damaged. 4. Replace the IPU. 5. Check if there are any signs of a short circuit on the SPDF/ARDF Main Board. If there are any defects, replace the board. |
| Error code: | SC621 |
| Description: | Mailbox-to-Finisher communication error. Communication between the mailbox and finisher is interrupted. An ACK/NCK signal was not received within 100 ms after a data frame is sent and 3 retries failed. |
| Causes: | The UART generated an error when the finisher was connected. |
| Remedy: | • Connection cable between mailbox and finisher disconnected, defective • Finisher main board defective • BICU defective • PSU defective |
| Error code: | SC622 |
| Description: | LCT communication error. Communication between the copier and LCT is interrupted. An ACK/NCK signal was not received within 100 ms after a data frame is sent and 3 retries failed. |
| Causes: | • Paper tray control board defective • BCU defective • IOB defective • Paper tray-main machine connection error |
| Remedy: | • Connection cable between the LCT and copier is disconnected, defective • LCT main board defective • BICU defective • PSU defective |
| Error code: | SC632-00 |
| Description: | Counter device error 1 After 3 attempts to send a data frame to the optional counter device via the serial communication line, no ACK signal was received within 100 ms. |
| Causes: | Serial line between the optional counter device, the relay board and copier control board is disconnected or damaged. |
| Remedy: | • Turn the main power off/on. • Check the serial communication line. |
| Error code: | SC633-00 |
| Description: | Counter device error 2 After communication was established, the controller received the brake signal from the accounting device. |
| Causes: | Serial line between the optional counter device, the relay board and copier control board is disconnected or damaged. |
| Remedy: | • Turn the main power off/on. • Check the serial communication line. |
| Error code: | SC634-00 |
| Description: | Counter device error 3 A backup RAM error was returned by the counter device. |
| Causes: | Counter device control board or the backup battery of counter device defective |
| Remedy: | • Replace the counter device control board. • Replace the backup battery. |
| Error code: | SC635-00 |
| Description: | Counter device error 4 A backup battery error was returned by the counter device. |
| Causes: | Counter device control board or the backup battery of counter device defective |
| Remedy: | • Replace the counter device control board. • Replace the backup battery. |
| Error code: | SC636-01 |
| Description: | IC Card Error (Expanded authentication module error) Issued when expanded authentication management is set to "ON" but either of the following occur. • There is no expanded authentication module in the machine. • The SD card or the file of the expanded authentication module is broken. • There is no DESS module in the machine. |
| Causes: | • There is no DESS module in the machine (models on which the function is optional). • There is no expanded authentication module in the machine. • The SD card or the file of the expanded authentication module is broken. |
| Remedy: | • Set a working SD card/expanded authentication module file. • Install the DESS module. • In the SSP mode set SP5-401-160 to "0". • In the SSP mode, set SP5-401-161 to "0". • Replace the NVRAM. |
| Error code: | SC636-02 |
| Description: | IC Card Error (Version error) The version of the expanded authentication module is not correct. |
| Causes: | Incorrect module version |
| Remedy: | Install the correct file of the expanded authentication module. |
| Error code: | SC636-11 |
| Description: | IC Card Error (OSM user code file error) • The correct "usercode" file could not be found in the root folder of the SD card. • The "usercode" file on the SD card could not be read. |
| Causes: | • The "usercode" file does not exist on the SD card. • The "usercode" file on the SD card is an invalid file. • Data in the "usercode" file on the SD card is invalid. • "usercode" file was not moved when moving the application to another SD card |
| Remedy: | Use the user code configuration tool for OSM users (Idissuer.exe) to create the "usercode" and store it in the root folder of the SD card containing the IC card module (eccm.mod). |
| Error code: | SC637-01 |
| Description: | Tracking Information Notification Error (Tracking application error) Tracking information was lost. |
| Causes: | • Tracking SDK application error • Internal notification error |
| Remedy: | Turn the main power off/on. |
| Error code: | SC637-02 |
| Description: | Tracking Information Notification Error (Management server error) Tracking information was lost. |
| Causes: | Communication with tracking management server failed. • Network error • tracking management server error • Tracking SDK application error |
| Remedy: | Turn the main power off/on. |
| Error code: | SC650-01 |
| Description: | Remote Service Modem Communication Error (Dialup authentication failure) • An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on. • Displayed only when an error is detected while RC Gate is operating. • SC is not issued if an error occurs during RC Gate installation (because it can be referenced using SP). |
| Causes: | Dialup authentication failure |
| Remedy: | Check the following SPs. • SP5-816-156 • SP5-816-157 |
| Error code: | SC650-04 |
| Description: | Remote Service Modem Communication Error (dialup failing because of incorrect modem configuration) • An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on. • Displayed only when an error is detected while RC Gate is operating. • SC is not issued if an error occurs during RC Gate installation (because it can be referenced using SP). |
| Causes: | Dialup failing because of incorrect modem configuration |
| Remedy: | Check if the setting of SP5-816-160 is correct. If it is correct, then there is a software bug. |
| Error code: | SC650-05 |
| Description: | Remote Service Modem Communication Error (insufficient current or connection error) • An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on. • Displayed only when an error is detected while RC Gate is operating. • SC is not issued if an error occurs during RC Gate installation (because it can be referenced using SP). |
| Causes: | Insufficient current or connection error |
| Remedy: | The line is not supported and nothing can be done. |
| Error code: | SC650-13 |
| Description: | Remote Service Modem Communication Error (RC Gate Type M was installed but modem is not present (detected during operation)) • An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on. • Displayed only when an error is detected while RC Gate is operating. • SC is not issued if an error occurs during RC Gate installation (because it can be referenced using SP). |
| Causes: | RC Gate Type M was installed but modem is not present (detected during operation) |
| Remedy: | • If a modem board is not installed, install it. • Check again if the modem driver configurations (SP5-816-160, SP5-816-165 to 171) are correct. • If the problem is not solved, replace the modem. |
| Error code: | SC650-14 |
| Description: | Remote Service Modem Communication Error (RC Gate Type N was installed but modem is present or wired/wireless LAN is not working correctly) • An error related to communication (dialup connection, modem board etc.) using the RC Gate was detected or an error that prevents RC Gate operation was detected at power on. • Displayed only when an error is detected while RC Gate is operating. • SC is not issued if an error occurs during RC Gate installation (because it can be referenced using SP). |
| Causes: | RC Gate Type N was installed but modem is present or wired/wireless LAN is not working correctly |
| Remedy: | • If a modem board is attached, remove it. • Check if wired/wireless LAN works. |
| Error code: | SC651-01 |
| Description: | Illegal Remote Service Dial-up (Chat program parameter error) An unexpected error occurred when RC Gate Type M dialed up the NRS Center. |
| Causes: | Software bug |
| Remedy: | Logging only. |
| Error code: | SC651-02 |
| Description: | Illegal Remote Service Dial-up (Chat program execution error) An unexpected error occurred when RC Gate dialed up the NRS Center. |
| Causes: | Software bug |
| Remedy: | Logging only. |
| Error code: | SC652-00 |
| Description: | Remote service ID2 mismatching There was an authentication mismatch between ID2 for @Remote, the controller board, and NVRAM. |
| Causes: | • Used controller board installed • Used NVRAM installed (such action is not allowed.) |
| Remedy: | • If this occurs during RC Gate installation: Check the validity of the certificate and the NVRAM, check the machine serial number, write the common certificate, and then begin installation again. • If this occurs after RC Gate installation: Clear the RC Gate install status, check the validity of the certificate and the NVRAM, check the machine serial number, write the common certificate, and then begin installation again. |
| Error code: | SC653-00 |
| Description: | Incorrect remote service ID2 |
| Causes: | ID2 stored in the NVRAM has either of the following problems. • Number of characters is not 17. • Includes a character that cannot be printed. • All spaces • NULL |
| Remedy: | Replace the NVRAM. Clear the RC Gate install status, write the common certificate, and then begin installation again |
| Error code: | SC669-01 |
| Description: | ID Error at NVRAM OPEN An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-02 |
| Description: | Channel Error at NVRAM OPEN An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-03 |
| Description: | Device Error at NVRAM OPEN An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-04 |
| Description: | Communication interrupt error at NVRAM OPEN An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-05 |
| Description: | Communication timeout error at NVRAM OPEN An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-06 |
| Description: | Operation interrupt error at NVRAM OPEN An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-07 |
| Description: | Buffer Full Error at NVRAM OPEN An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-08 |
| Description: | No error code at NVRAM OPEN An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-09 |
| Description: | ID error at NVRAM CLOSE An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-10 |
| Description: | No error code at NVRAM CLOSE An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-11 |
| Description: | ID Error When Writing Data to NVRAM An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-12 |
| Description: | Channel error when writing data to NVRAM An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-13 |
| Description: | Device error when writing data to NVRAM An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-14 |
| Description: | Communication interrupt error when writing data to NVRAM An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-15 |
| Description: | Communication timeout error when writing data to NVRAM An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-16 |
| Description: | Operation interrupt error when writing data to NVRAM An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-17 |
| Description: | Buffer full error when writing data to NVRAM An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-18 |
| Description: | No error code when writing data to NVRAM An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-19 |
| Description: | ID error when reading data from NVRAM An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-20 |
| Description: | Channel error when reading data from NVRAM An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-21 |
| Description: | Device error when reading data from NVRAM An error occurred during communication with the NVRAM on the BICU. Three attempts to communicate with NVRAM failed. |
| Causes: | • Electronic noise • NVRAM missing, not mounted on BICU • NVRAM not installed correctly • NVRAM damaged • BICU damaged |
| Remedy: | • Cycle the machine off/on. • If the error persists, first determine if there is any electronic noise on the power line or around the machine. • Remove the rear upper cover and inspect the NVRAM on the BICU. • Confirm that the NVRAM is installed, undamaged, and installed correctly. • Make sure that the pins of the NVRAM are seated correctly (not bent out of place). • Replace NVRAM. • Replace BICU. |
| Error code: | SC669-22 |
| Description: | EEPROM Data read: Communication abort error |
| Causes: | Received a error notification during EEPROM communication and doesnot resume after 3 retries. • Electrical noise • EEPROM not connected fully • EEPROM not installed • EEPROM damaged • BCU damaged |
| Remedy: | • Turn the power off/on • Reconnect the EEPROM • Replace the EEPROM • Replace the BCU |
| Error code: | SC669-23 |
| Description: | EEPROM Data read: Communication timeout error |
| Causes: | Received a error notification during EEPROM communication and doesnot resume after 3 retries. • Electrical noise • EEPROM not connected fully • EEPROM not installed • EEPROM damaged • BCU damaged |
| Remedy: | • Turn the power off/on • Reconnect the EEPROM • Replace the EEPROM • Replace the BCU |
| Error code: | SC669-24 |
| Description: | EEPROM Data read: Operation stopped error |
| Causes: | Received a error notification during EEPROM communication and doesnot resume after 3 retries. • Electrical noise • EEPROM not connected fully • EEPROM not installed • EEPROM damaged • BCU damaged |
| Remedy: | • Turn the power off/on • Reconnect the EEPROM • Replace the EEPROM • Replace the BCU |
| Error code: | SC669-25 |
| Description: | EEPROM Data read: Buffer full |
| Causes: | Received a error notification during EEPROM communication and doesnot resume after 3 retries. • Electrical noise • EEPROM not connected fully • EEPROM not installed • EEPROM damaged • BCU damaged |
| Remedy: | • Turn the power off/on • Reconnect the EEPROM • Replace the EEPROM • Replace the BCU |
| Error code: | SC669-26 |
| Description: | EEPROM Data read: No error code |
| Causes: | Received a error notification during EEPROM communication and doesnot resume after 3 retries. • Electrical noise • EEPROM not connected fully • EEPROM not installed • EEPROM damaged • BCU damaged |
| Remedy: | • Turn the power off/on • Reconnect the EEPROM • Replace the EEPROM • Replace the BCU |
| Error code: | SC669-36 |
| Description: | EEPROM: Verify Error The machine receives an error notification during EEPROM (BCU) communication and does not resume after 2 retries. The machine detects an abnormal value in the EEPROM data when starting up, or recovery from energy saver mode. |
| Causes: | • Electrical noise • EEPROM not connected fully • EEPROM damaged • BCU damaged |
| Remedy: | • Turn the power off/on. • Check the EEPROM. • Replace the EEPROM. • Replace the BCU. |
| Error code: | SC670-00 |
| Description: | Engine start up error Case 1 • /ENGRDY signal was not asserted when the machine was turned on or returned from energy saver mode. • /IPURDY signal was not asserted when the machine was turned on or returned from energy saver mode. • EC response was not received within specified time from power on. • PC response was not received within specified time from power on. • SC response was not received within specified time from power on. • Writing to Rapi driver failed (the other party not found through PCI). Case 2 • Unexpected down status was detected after /ENGRDY assertion. |
| Causes: | Case 1 • Engine board does not start up. Case 2 • Engine board reset unexpectedly. |
| Remedy: | Check the connection between the engine board and the controller board. • If it is always reproduced, replace the engine board. If the problem persists, consider replacing the controller board or other boards between them. • If reproducibility is low, multiple causes are to be considered, such as software, engine board, controller board, and PSU. |
| Error code: | SC672-10 |
| Description: | Controller start up error After the machine was powered on, communication between the controller and the operation panel was not established. |
| Causes: | • Controller stalled • Board installed incorrectly • Controller board defective • Operation panel connector loose, broken, or defective • Controller late |
| Error code: | SC672-11 |
| Description: | Controller start up error After the machine was powered on, communication between the controller and the operation panel was not established, or communication with controller was interrupted after a normal startup. |
| Causes: | • Controller stalled • Board installed incorrectly • Controller board defective • Operation panel connector loose, broken, or defective • Controller late |
| Error code: | SC672-12 |
| Description: | Controller start up error Communication with controller was interrupted after a normal startup. |
| Causes: | • Controller stalled • Board installed incorrectly • Controller board defective • Operation panel connector loose, broken, or defective • Controller late |
| Error code: | SC672-13 |
| Description: | Controller start up error The operation panel detects that the controller is down due to other reason shown in SC672- 10, SC672-11, and SC672-12. |
| Causes: | • Controller stalled • Board installed incorrectly • Controller board defective • Operation panel connector loose, broken, or defective • Controller late |
| Error code: | SC672-99 |
| Description: | Controller start up error The operation panel software ended abnormally. |
| Causes: | • Controller stalled • Board installed incorrectly • Controller board defective • Operation panel connector loose, broken, or defective • Controller late |
| Error code: | SC687 |
| Description: | Memory address command error. The BICU does not receive a memory address command from the controller 120 seconds after paper is in the position for registration. |
| Causes: | The BICU did not receive a memory address command from the controller within the prescribed time after the paper reached the registration sensor. |
| Remedy: | • BICU-Controller connection loose, defective • BICU defective • Controller defective |
| Error code: | SC701-03 |
| Description: | Paper Feed Motor Driver Error (ARDF) Detection of error signal from motor driver |
| Causes: | • Encoder disconnection • Encoder connector dropout • Encoder defective • Overload • Motor deterioration |
| Remedy: | • Replace the encoder harness • Check the harness connection • Replace the motor |
| Error code: | SC701-08 |
| Description: | Paper Exit Motor Driver Error (ARDF) Detection of error signal from motor driver. |
| Causes: | • Encoder disconnection • Encoder connector dropout • Encoder defective • Overload • Motor deterioration |
| Remedy: | • Replace the encoder harness • Check the harness connection • Replace the motor |
| Error code: | SC702-01 |
| Description: | ARDF DF3090 (D779) Error Protection Device Intercept Error When original source 5V power supply is ON, protection device intercept of 24V power supply system is detected |
| Causes: | Any of feed motor, transport motor, reverse solenoid, paper feed solenoid, paper feed clutch and FAN motor defective, a harness shortcircuit occurs, and the protection device of the 24V power supply system intercepts. |
| Remedy: | Check if the SC occurs by turning the main power OFF then ON, opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. • The target parts that need to be checked are all motors, all solenoids, and all clutches. 1. Check if the connector of the target part is connected securely. Reconnect the connector if it is disconnected, or loose. 2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged. 3. Check if the specific part runs (OUTPUT Check), has no overloads, and is properly driven. Replace the part if there are any defects. 4. Check if there are any signs of a short circuit. Replace the parts if there are any defects. |
| Error code: | SC702-02 |
| Description: | ARDF DF3090 (D779) Error Protection Device Intercept Error 2 When original source 5V power supply is ON, protection device intercept of 24V OUT power supply system is detected. |
| Causes: | Solenoid defective or harness short-circuit occurs in 24VOUT power supply system. |
| Remedy: | Check if the SC occurs by turning the main power OFF then ON, opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. • The target parts that need to be checked are all motors, all solenoids, and all clutches. 1. Check if the connector of the target part is connected securely. Reconnect the connector if it is disconnected, or loose. 2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged. 3. Check if the specific part runs (OUTPUT Check), has no overloads, and is properly driven. Replace the part if there are any defects. 4. Check if there are any signs of a short circuit. Replace the parts if there are any defects. |
| Error code: | SC702-03 |
| Description: | ARDF DF3090 (D779) Error Protection Device Intercept Error 3 When original source 5V power supply is ON, protection device intercept of 5VE power supply system is detected. |
| Causes: | Sensor defective or a harness short-circuit occur in 5VE power supply system. |
| Remedy: | Check if the SC occurs by turning the main power OFF then ON, opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Check if the connector for Original Set Sensor is connected securely. Reconnect the connector if it is disconnected, or loose. 2. Check the harness for Original Set Sensor. Replace the harness if it is disconnected, or damaged. 3. Check if the Original Set Sensor turns OFF/ON (INPUT Check). Replace the part if there are any defects. 4. Check if there are any signs of a short circuit. Replace the parts if there are any defects. |
| Error code: | SC721-03 |
| Description: | Protection device break error 1 (Finisher SR5070/SR5080) 24V_INT_1 power supply level error. (SC from the first time) |
| Causes: | • Motor defective • Harness broken |
| Remedy: | • Turn the machine OFF/ON. • Replace the harness. • Replace the defective motor. It could be any of the following: Entrance Motor, Registration motor, Junction gate motor, Horizontal transport motor, Pre-stack motor, Stapler entrance motor, Leading edge stopper motor, Base fence movement motor, Base fence lift motor, Feed-out belt motor, Trailing edge press motor, Stapler movement motor, Corner stapler motor, Positioning roller lift motor, Positioning roller rotation motor, Jogger motor (front), Jogger motor (rear), Trimmings shutter solenoid, PSU cooling fan motor • Replace the board. |
| Error code: | SC721-10 |
| Description: | Booklet Finisher SR3220 (D3B9) Error Transport Motor 1 Error Motor driver detects an error state (DC motor control error) (1st time is jam notification, 2nd time is SC notification). |
| Causes: | • Overcurrent (-03 only) • Staple jam (-44 only) • Encoder error (-11, -11, -25, -44) • Motor defective • Connecter disconnected, or loose • Motor overload • HP sensor defective • Paper surface sensor defective (-70 only |
| Remedy: | Check if the SC occurs by opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. • The target parts are the motor and related HP sensor that SC occurred. 1. Check if the connector of the target part is connected securely. Reconnect the connector if it is disconnected, or loose. 2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged. 3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects. 4. Check if there are any signs of a short circuit. Replace the parts if there are any defects. |
| Error code: | SC721-11 |
| Description: | Booklet Finisher SR3220 (D3B9) Error Transport Motor 2 Error Motor driver detects an error state (DC motor control error) (1st time is jam notification, 2nd time is SC notification). |
| Causes: | • Overcurrent (-03 only) • Staple jam (-44 only) • Encoder error (-11, -11, -25, -44) • Motor defective • Connecter disconnected, or loose • Motor overload • HP sensor defective • Paper surface sensor defective (-70 only |
| Remedy: | Check if the SC occurs by opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. • The target parts are the motor and related HP sensor that SC occurred. 1. Check if the connector of the target part is connected securely. Reconnect the connector if it is disconnected, or loose. 2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged. 3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects. 4. Check if there are any signs of a short circuit. Replace the parts if there are any defects. |
| Error code: | SC721-17 |
| Description: | Booklet Finisher SR3220 (D3B9) Error Paper Eject Motor 2 Error Motor driver detects an error state (DC motor control error) (1st time is jam notification, 2nd time is SC notification). |
| Causes: | • Overcurrent (-03 only) • Staple jam (-44 only) • Encoder error (-11, -11, -25, -44) • Motor defective • Connecter disconnected, or loose • Motor overload • HP sensor defective • Paper surface sensor defective (-70 only |
| Remedy: | Check if the SC occurs by opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. • The target parts are the motor and related HP sensor that SC occurred. 1. Check if the connector of the target part is connected securely. Reconnect the connector if it is disconnected, or loose. 2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged. 3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects. 4. Check if there are any signs of a short circuit. Replace the parts if there are any defects. |
| Error code: | SC721-24 |
| Description: | Junction Gate Transport Motor Error (Finisher SR5070/SR5080) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) |
| Causes: | • Junction gate transport motor defective • Connector disconnected • Overload • Junction gate home position sensor defective |
| Remedy: | • Turn the machine OFF/ON. • Reconnect the motor connector and sensor connector. • Replace the junction gate home position sensor. • Replace the junction gate transport motor. |
| Error code: | SC721-25 |
| Description: | Punch Motor Error (Finisher SR5070/SR5080) • After the punch motor was turned ON, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • After the punch motor was turned ON, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) |
| Causes: | • Punch motor defective • Connector disconnected • Overload • Home position sensor defective |
| Remedy: | • Turn the machine OFF/ON. • Reconnect the motor connector and sensor connector. • Replace the home position sensor. • Replace the punch motor. |
| Error code: | SC721-27 |
| Description: | Punch Movement Motor Error (Finisher SR5070/SR5080) • After driving the punch movement motor, the motor did not back to the home position within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • After driving the punch movement motor, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) |
| Causes: | • Punch movement motor defective • Connector disconnected • Overload |
| Remedy: | • Turn the machine OFF/ON. • Reconnect the motor connector. • Replace the punch movement motor. |
| Error code: | SC721-28 |
| Description: | Punch Horizontal Registration Detection Error (1K sheet finisher) |
| Causes: | • Over current (board defective, harness short-circuit, solenoid defective) (*721-03 only) • Motor defective (*excluding 721-03) • Connector disconnected (*excluding 721-03) • Overload (*excluding 721-03) • Encoder error (*720-10, 11, 17, 25, 44 only) • Home position sensor error (*Excluding 721-03, 10, 11, 17, 70, and 80) • Retreat sensor error (*721-42 only) • Needle jam (*721-44 only) • Home position sensor (folding blade HP) error (*721-52 only) • Home position sensor (folding cam HP) error (*721-52 only) • Paper surface sensor error (*721-70 only) |
| Remedy: | • Replace the controller • Replace the harness • Replace the motor (*excluding SC721-03) • Reset the connector (*excluding SC721-03) • Replace the solenoid (*SC721-03 only) • Replace the home position sensor (*excluding SC721-03, 10, 11, 17, 80) |
| Error code: | SC721-30 |
| Description: | Jogger Motor 1 Error (1K sheet finisher) |
| Causes: | • Over current (board defective, harness short-circuit, solenoid defective) (*721-03 only) • Motor defective (*excluding 721-03) • Connector disconnected (*excluding 721-03) • Overload (*excluding 721-03) • Encoder error (*720-10, 11, 17, 25, 44 only) • Home position sensor error (*Excluding 721-03, 10, 11, 17, 70, and 80) • Retreat sensor error (*721-42 only) • Needle jam (*721-44 only) • Home position sensor (folding blade HP) error (*721-52 only) • Home position sensor (folding cam HP) error (*721-52 only) • Paper surface sensor error (*721-70 only) |
| Remedy: | • Replace the controller • Replace the harness • Replace the motor (*excluding SC721-03) • Reset the connector (*excluding SC721-03) • Replace the solenoid (*SC721-03 only) • Replace the home position sensor (*excluding SC721-03, 10, 11, 17, 80) |
| Error code: | SC721-33 |
| Description: | Positioning Roller Lift Motor Error (Finisher SR5070/SR5080) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) |
| Causes: | • Positioning roller lift motor defective • Connector disconnected • Overload • Home position sensor defective |
| Remedy: | • Turn the machine OFF/ON. • Reconnect the motor connector and sensor connector. • Replace the home position sensor. • Replace the positioning roller lift motor. |
| Error code: | SC721-41 |
| Description: | Feed Out Belt Motor Error (Finisher SR5070/SR5080) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • DCM drive software detected the motor drive error. • During the initialization (after executing retry): the first time error is the jam display, the second time error is the SC. • Except the initialization: the SC is issued from the first time. |
| Causes: | • Feed out belt motor defective • Connecter disconnected • Overload • Encoder defective • Home position sensor defective |
| Remedy: | • Turn the machine OFF/ON. • Reconnect the motor connector and the sensor connector. • Replace the home position sensor. • Replace the feed out belt motor. |
| Error code: | SC721-42 |
| Description: | Stapler Movement Motor Error (Finisher SR5070/SR5080) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) • DCM drive software detected the motor drive error. (SC from the first time) |
| Causes: | • Stapler movement motor defective • Connecter disconnected • Overload • Encoder defective • Home position sensor defective |
| Remedy: | • Turn the machine OFF/ON. • Reconnect the motor connector and the sensor connector. • Replace the home position sensor. • Replace the stapler movement motor. |
| Error code: | SC721-44 |
| Description: | Booklet Stapler Motor Error (Finisher SR5070/SR5080) • The staple drive unit does not complete operation within specified time (t0 ms). (The first time: jam display, the second time: SC) • When moving to the home position, home position was not detected within specified time (t1 ms). (The first time: jam display, the second time: SC) |
| Causes: | • Overload due to staple jam or number of sheets exceeding the limit, etc. • Booklet stapler motor defective • Connector disconnected • Home position sensor defective |
| Remedy: | 1. Removing the overload • Remove the staple jam. • Check the number of sheets 2. Checking the following • Turn the machine OFF/ON. • Reconnect the motor connector and the sensor connector. • Replace the home position sensor. • Replace the booklet stapler motor. |
| Error code: | SC721-52 |
| Description: | Booklet Finisher SR3220 (D3B9) Error Folding Plate Drive Motor Error • Motor driver detects an error (short-circuit and overheating) (1st time is SC). • During movement to home, the home position could not be detected within a predetermined pulse (1st time is jam notification, 2nd time is SC notification). • During movement from home, the home position was detected for longer than a predetermined pulse (1st time is jam notification, 2nd time is SC notification). |
| Causes: | • Overcurrent (-03 only) • Staple jam (-44 only) • Encoder error (-11, -11, -25, -44) • Motor defective • Connecter disconnected, or loose • Motor overload • HP sensor defective • Paper surface sensor defective (-70 only |
| Remedy: | Check if the SC occurs by opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. • The target parts are the motor and related HP sensor that SC occurred. 1. Check if the connector of the target part is connected securely. Reconnect the connector if it is disconnected, or loose. 2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged. 3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects. 4. Check if there are any signs of a short circuit. Replace the parts if there are any defects. |
| Error code: | SC721-53 |
| Description: | Booklet Finisher SR3220 (D3B9) Error Rear End Fence Displacement Motor Error • During movement to home, the home position could not be detected within a predetermined pulse (1st time is jam notification, 2nd time is SC notification). • During movement from home, the home position was detected for longer than a predetermined pulse (1st time is jam notification, 2nd time is SC notification). |
| Causes: | • Overcurrent (-03 only) • Staple jam (-44 only) • Encoder error (-11, -11, -25, -44) • Motor defective • Connecter disconnected, or loose • Motor overload • HP sensor defective • Paper surface sensor defective (-70 only |
| Remedy: | Check if the SC occurs by opening/closing covers, and input/output check. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. • The target parts are the motor and related HP sensor that SC occurred. 1. Check if the connector of the target part is connected securely. Reconnect the connector if it is disconnected, or loose. 2. Check the harness for the target part. Replace the harness if it is disconnected, or damaged. 3. Check if the motor runs, sensors turn OFF/ON, has no overloads, and is properly driven. Replace the parts if there are any defects. 4. Check if there are any signs of a short circuit. Replace the parts if there are any defects. |
| Error code: | SC721-58 |
| Description: | Bundle Transport 1 Release Motor Error (1K sheet finisher) |
| Causes: | • Over current (board defective, harness short-circuit, solenoid defective) (*721-03 only) • Motor defective (*excluding 721-03) • Connector disconnected (*excluding 721-03) • Overload (*excluding 721-03) • Encoder error (*720-10, 11, 17, 25, 44 only) • Home position sensor error (*Excluding 721-03, 10, 11, 17, 70, and 80) • Retreat sensor error (*721-42 only) • Needle jam (*721-44 only) • Home position sensor (folding blade HP) error (*721-52 only) • Home position sensor (folding cam HP) error (*721-52 only) • Paper surface sensor error (*721-70 only) |
| Remedy: | • Replace the controller • Replace the harness • Replace the motor (*excluding SC721-03) • Reset the connector (*excluding SC721-03) • Replace the solenoid (*SC721-03 only) • Replace the home position sensor (*excluding SC721-03, 10, 11, 17, 80) |
| Error code: | SC721-59 |
| Description: | Bundle Transport 2 Release Motor Error (1K sheet finisher) • During movement to home, the home position could not be detected within a predetermined pulse (p0 pulse) (1st time is jam notification, 2nd time is SC notification). • During movement from home, the home position was detected for longer than a predetermined pulse (p1 pulse) (1st time is jam notification, 2nd time is SC notification). The return pulse to home and pulse coming from home during normal operation are calculated and measured. The pulses which are 1.5-2 times the normal operation pulse are taken as p0 and p1. |
| Causes: | • Over current (board defective, harness short-circuit, solenoid defective) (*721-03 only) • Motor defective (*excluding 721-03) • Connector disconnected (*excluding 721-03) • Overload (*excluding 721-03) • Encoder error (*720-10, 11, 17, 25, 44 only) • Home position sensor error (*Excluding 721-03, 10, 11, 17, 70, and 80) • Retreat sensor error (*721-42 only) • Needle jam (*721-44 only) • Home position sensor (folding blade HP) error (*721-52 only) • Home position sensor (folding cam HP) error (*721-52 only) • Paper surface sensor error (*721-70 only) |
| Remedy: | • Replace the controller • Replace the harness • Replace the motor (*excluding SC721-03) • Reset the connector (*excluding SC721-03) • Replace the solenoid (*SC721-03 only) • Replace the home position sensor (*excluding SC721-03, 10, 11, 17, 80) |
| Error code: | SC721-70 |
| Description: | Tray 1 Lift Motor Error (Finisher SR5070/SR5080) • When descending, paper sensor is still detecting paper after the specified time (t0 sec). (The first time: jam display, the second time: SC) • When ascending, paper sensor did not detect paper within specified time (t1 sec). (The first time: jam display, the second time: SC) |
| Causes: | • Motor defective • Connector disconnected • Overload • Paper sensor defective |
| Remedy: | • Turn the machine OFF/ON. • Reconnect the motor connector and the sensor connector. • Replace the paper sensor. • Replace the defective motor. |
| Error code: | SC721-71 |
| Description: | Shift Motor 1 Error (tray/shift roller) (Finisher SR5070/SR5080) • When moving to the home position, home position was not detected within specified number of pulses (p0 pulses). (The first time: jam display, the second time: SC) • When moving from the home position, home position was still detected after specified number of pulses (p1 pulses). (The first time: jam display, the second time: SC) |
| Causes: | • Motor defective • Connector disconnected • Overload • Home position sensor defective |
| Remedy: | • Turn the machine OFF/ON. • Reconnect the motor connector and the sensor connector. • Replace the home position sensor. • Replace the defective motor. |
| Error code: | SC721-80 |
| Description: | Interlock Power Error (Finisher SR5070/SR5080) 24V_INT power supply level error. (SC from the first time) |
| Causes: | • Controller board power circuit defective |
| Remedy: | • Turn the machine OFF/ON. • Replace the controller board. |
| Error code: | SC770 |
| Description: | Cover interposer tray bottom plate motor error. • After the motor starts to raise the bottom plate, the bottom plate position sensor does not detect the plate at the specified time (3 s). • After the motor starts to lower the bottom plate, the bottom plate HP sensor does not detect the bottom plate. |
| Causes: | In the first tray: • The upper limit sensor did not detect the bottom plate within the specified time after the lift motor switched on to lift the bottom plate. • The lower limit sensor did not direct the bottom plate within the specified time after the lift motor switched on to lower the bottom plate. Note: In both cases, 1 error count indicates a jam, 2 error counts issue this SC code. |
| Remedy: | • Bottom plate position sensor, disconnected, defective • Bottom plate HP sensor disconnected, defective |
| Error code: | SC791 |
| Description: | Booklet stapler bottom fence motor Booklet Finisher (D512) |
| Causes: | The bottom fence failed to return to home position or failed to leave the home position within the prescribed time. |
| Remedy: | • An obstruction is blocking the movement of the bottom fence • Motor harness disconnected or defective • Bottom fence HP sensor disconnected or defective • Motor defective • Sensor defective |
| Error code: | SC792 |
| Description: | No finisher, bridge unit provided When power supply is switched on, it is recognized there is no finisher, and a bridge unit is fitted. |
| Causes: | • Finisher connector set fault • In a machine which has a bridge unit connected, a finisher is not fitted • Finisher defective |
| Remedy: | Connect finisher or disconnect bridge unit, and turn the power off/on |
| Error code: | SC793-01 |
| Description: | Front jogger motor error with 1-bin tray (D586) The machine does not detect a correct signal from the front jogger fence HP sensor while the front jogger motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective front jogger motor • Loosen connection • Motor overload • Defective front jogger fence HP sensor |
| Remedy: | • Reset the connector • Replace the front jogger fence HP sensor. • Replace the front jogger motor. |
| Error code: | SC793-02 |
| Description: | Rear jogger motor error with 1-bin tray (D586) The machine does not detect a correct signal from the rear jogger fence HP sensor while the rear jogger motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective front jogger motor • Loosen connection • Motor overload • Defective front jogger fence HP sensor |
| Remedy: | • Reset the connector • Replace the front jogger fence HP sensor. • Replace the front jogger motor. |
| Error code: | SC793-03 |
| Description: | Pick-up roller contact motor error with 1-bin tray (D586) The machine does not detect a correct signal from the pick-up roller HP sensor while the pick-up roller contact motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective pick-up roller contact motor • Loosen connection • Motor overload • Defective pick-up roller HP sensor |
| Remedy: | • Reset the connector • Replace the pick-up roller HP sensor. • Replace the pick-up roller contact motor. |
| Error code: | SC793-04 |
| Description: | Exit guide plate motor error with 1-bin tray (D586) The machine does not detect a correct signal from the exit guide plate HP sensor while the exit guide plate motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective exit guide plate motor • Loosen connection • Motor overload • Defective exit guide plate HP sensor |
| Remedy: | • Reset the connector • Replace the exit guide plate HP sensor. • Replace the exit guide plate motor. |
| Error code: | SC793-05 |
| Description: | Output tray motor error with 1-bin tray (D586) The machine does not detect a correct signal from the stack height detection lever sensor while the output tray motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective output tray motor • Loosen connection • Motor overload • Defective stack height detection lever sensor |
| Remedy: | • Reset the connector • Replace the stack height detection lever sensor. • Replace the output tray motor. |
| Error code: | SC793-06 |
| Description: | Stack height detection lever motor error with 1-bin tray (D586) The machine does not detect a correct signal from the stack height detection lever HP sensor while the stack height detection lever motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective stack height detection lever motor • Loosen connection • Motor overload • Defective stack height detection lever HP sensor • Defective stack height detection lever sensor |
| Remedy: | • Reset the connector • Replace the stack height detection lever sensor. • Replace the output tray motor. |
| Error code: | SC793-07 |
| Description: | Punch drive motor error with 1-bin tray (D586) The machine does not detect a correct signal from the punch position sensor while the punch drive motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective punch drive motor • Loosen connection • Motor overload • Defective punch position sensor |
| Remedy: | • Reset the connector • Replace the punch position sensor. • Replace the punch drive motor. |
| Error code: | SC793-08 |
| Description: | Punch movement motor error with 1-bin tray (D586) The machine does not detect a correct signal from the punch position sensor while the punch movement motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective punch movement motor • Loosen connection • Motor overload • Defective punch position sensor |
| Remedy: | • Reset the connector • Replace the punch position sensor. • Replace the punch movement motor. |
| Error code: | SC793-09 |
| Description: | Paper position sensor unit motor error with 1-bin tray (D586) The machine does not detect a correct signal from the paper position detection unit HP sensor while paper position sensor unit motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective paper position sensor unit motor • Loosen connection • Motor overload • Defective paper position detection unit HP sensor |
| Remedy: | • Reset the connector • Replace the paper position detection unit HP sensor. • Replace the paper position sensor unit motor. |
| Error code: | SC793-11 |
| Description: | Stapler unit motor error with 1-bin tray (D586) The machine does not detect a correct signal from the stapler unit motor HP sensor while the stapler unit motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective stapler unit motor • Loosen connection • Motor overload • Defective stapler unit motor HP sensor |
| Remedy: | • Reset the connector • Replace the stapler unit HP sensor. • Replace the stapler unit motor. |
| Error code: | SC793-12 |
| Description: | Shift roller motor error with 1-bin tray (D586) The machine does not detect a correct signal from the shift roller HP sensor while the shift roller motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective shift roller motor • Loosen connection • Motor overload • Defective shift roller HP sensor |
| Remedy: | • Reset the connector • Replace the shift roller HP sensor. • Replace the shift roller motor. |
| Error code: | SC794-01 |
| Description: | Front jogger motor error without 1-bin tray (D586) The machine does not detect a correct signal from the front jogger fence HP sensor while the front jogger motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective front jogger motor • Loosen connection • Motor overload • Defective front jogger fence HP sensor |
| Remedy: | • Reset the connector • Replace the front jogger fence HP sensor. • Replace the front jogger motor. |
| Error code: | SC794-02 |
| Description: | Rear jogger motor error without 1-bin tray (D586) The machine does not detect a correct signal from the rear jogger fence HP sensor while the rear jogger motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective front jogger motor • Loosen connection • Motor overload • Defective front jogger fence HP sensor |
| Remedy: | • Reset the connector • Replace the front jogger fence HP sensor. • Replace the front jogger motor. |
| Error code: | SC794-03 |
| Description: | Pick-up roller contact motor error without 1-bin tray (D586) The machine does not detect a correct signal from the pick-up roller HP sensor while the pick-up roller contact motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective pick-up roller contact motor • Loosen connection • Motor overload • Defective pick-up roller HP sensor |
| Remedy: | • Reset the connector • Replace the pick-up roller HP sensor. • Replace the pick-up roller contact motor. |
| Error code: | SC794-04 |
| Description: | Exit guide plate motor error without 1-bin tray (D586) The machine does not detect a correct signal from the exit guide plate HP sensor while the exit guide plate motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective exit guide plate motor • Loosen connection • Motor overload • Defective exit guide plate HP sensor |
| Remedy: | • Reset the connector • Replace the exit guide plate HP sensor. • Replace the exit guide plate motor. |
| Error code: | SC794-05 |
| Description: | Output tray motor error without 1-bin tray (D586) The machine does not detect a correct signal from the stack height detection lever sensor while the output tray motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective output tray motor • Loosen connection • Motor overload • Defective stack height detection lever sensor |
| Remedy: | • Reset the connector • Replace the stack height detection lever sensor. • Replace the output tray motor. |
| Error code: | SC794-06 |
| Description: | Stack height detection lever motor error without 1-bin tray (D586) The machine does not detect a correct signal from the stack height detection lever HP sensor while the stack height detection lever motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective stack height detection lever motor • Loosen connection • Motor overload • Defective stack height detection lever HP sensor • Defective stack height detection lever sensor |
| Remedy: | • Reset the connector • Replace the stack height detection lever sensor. • Replace the output tray motor. |
| Error code: | SC794-07 |
| Description: | Punch drive motor error without 1-bin tray (D586) The machine does not detect a correct signal from the punch position sensor while the punch drive motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective punch drive motor • Loosen connection • Motor overload • Defective punch position sensor |
| Remedy: | • Reset the connector • Replace the punch position sensor. • Replace the punch drive motor. |
| Error code: | SC794-08 |
| Description: | Punch movement motor error without 1-bin tray (D586) The machine does not detect a correct signal from the punch position sensor while the punch movement motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective punch movement motor • Loosen connection • Motor overload • Defective punch position sensor |
| Remedy: | • Reset the connector • Replace the punch position sensor. • Replace the punch movement motor. |
| Error code: | SC794-09 |
| Description: | Paper position sensor unit motor error without 1-bin tray (D586) The machine does not detect a correct signal from the paper position detection unit HP sensor while paper position sensor unit motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective paper position sensor unit motor • Loosen connection • Motor overload • Defective paper position detection unit HP sensor |
| Remedy: | • Reset the connector • Replace the paper position detection unit HP sensor. • Replace the paper position sensor unit motor. |
| Error code: | SC794-10 |
| Description: | Stapler motor error. The machine does not detect a correct signal from the stapler motor HP sensor while thestapler motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Staple jam • Defective stapler motor • Loosen connection • Motor overload • Defective stapler motor HP sensor |
| Remedy: | • Remove the jammed staple. • Reset the connector • Replace the stapler motor HP sensor. • Replace the stapler motor. |
| Error code: | SC794-11 |
| Description: | Stapler unit motor error without 1-bin tray (D586) The machine does not detect a correct signal from the stapler unit motor HP sensor while the stapler unit motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective stapler unit motor • Loosen connection • Motor overload • Defective stapler unit motor HP sensor |
| Remedy: | • Reset the connector • Replace the stapler unit HP sensor. • Replace the stapler unit motor. |
| Error code: | SC794-12 |
| Description: | Shift roller motor error without 1-bin tray (D586) The machine does not detect a correct signal from the shift roller HP sensor while the shift roller motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective shift roller motor • Loosen connection • Motor overload • Defective shift roller HP sensor |
| Remedy: | • Reset the connector • Replace the shift roller HP sensor. • Replace the shift roller motor. |
| Error code: | SC816-01 |
| Description: | Subsystem error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-02 |
| Description: | Sysarch (LPUX_GET_PORT_INFO) error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-03 |
| Description: | Transition to STR was denied. |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-04 |
| Description: | Interrupt in kernel communication driver |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-05 |
| Description: | Preparation for transition to STR failed. |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-07 |
| Description: | Sysarch (LPUX_GET_PORT_INFO) error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-08 |
| Description: | Sysarch (LPUX_ENGINE_TIMERCTRL) error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-09 |
| Description: | Sysarch (LPUX_RETURN_FACTOR_STR) error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-10 |
| Description: | Sysarch (LPUX_GET_PORT_INFO) error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-11 |
| Description: | Sysarch (LPUX_GET_PORT_INFO) error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-12 |
| Description: | Sysarch (LPUX_GET_PORT_INFO) error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-13 |
| Description: | open() error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-14 |
| Description: | Memory address error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-15 |
| Description: | open() error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-19 |
| Description: | Double open() error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-20 |
| Description: | open() error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-22 |
| Description: | Parameter error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-23 |
| Description: | read() error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-24 |
| Description: | read() error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-25 |
| Description: | read() error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-26 |
| Description: | write() communication retry error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-29 |
| Description: | write() communication retry error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-35 |
| Description: | read() error |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC816-36 |
| Description: | Subsystem error |
| Causes: | Energy save I/O subsystem detected some abnormality. • Energy save I/O subsystem defective • Energy save I/O subsystem detected a controller board error (non-response). • Error was detected during preparation for transition to STR. |
| Remedy: | • Turn the main power off/on. • Replace the controller board. |
| Error code: | SC841-00 |
| Description: | EEPROM read data error Mirrored data of the EEPROM is different from the original data in EEPROM. |
| Causes: | Data in the EEPROM is overwritten for some reason. |
| Error code: | SC842-00 |
| Description: | Nand-Flash updating verification error SCS write error (verify error) occurred at the Nand-Flash module when remote ROM or main ROM was updated. |
| Causes: | Nand-Flash defective |
| Remedy: | Turn the main power OFF/ON. |
| Error code: | SC842-01 |
| Description: | Insufficient Nand-Flash blocks (threshold exceeded) At startup, or when machine returned from low power mode, the Nand-Flash status was read and judged that the number of unusable blocks had exceeded threshold, and then SCS generated the SC code. |
| Causes: | Number of unusable blocks exceeded threshold for Nand-Flash |
| Remedy: | Replace the controller board. |
| Error code: | SC842-02 |
| Description: | Number of Nand-Flash block deletions exceeded At startup, or when the machined returned from low power mode, the Nand-Flash was read and judged that the number of deleted blocks had exceeded threshold, and then SCS generated this SC code. |
| Causes: | Number of blocks deleted exceeded threshold for Nand-Flash |
| Remedy: | Replace the controller board. |
| Error code: | SC853-00 |
| Description: | Bluetooth device connection error The Bluetooth hardware (USB type) was connected after the machine was turned on. |
| Causes: | The Bluetooth hardware (USB type) was connected after the machine was turned on. |
| Remedy: | Always connect the Bluetooth device (USB type) before the machine is turned on. |
| Error code: | SC854-00 |
| Description: | Bluetooth device disconnected The Bluetooth hardware (USB type) was disconnected after the machine was turned on. |
| Causes: | The Bluetooth hardware (USB type) was disconnected after the machine was turned on. |
| Remedy: | Never remove Bluetooth (USB type) after machine starts |
| Error code: | SC855-01 |
| Description: | Wireless LAN board error (driver attachment failure) Wireless LAN board error (wireless LAN card: 802.11 is covered) |
| Causes: | • Defective wireless LAN board • Loose connection |
| Remedy: | • Turn the main power OFF/ON. • Replace wireless LAN board |
| Error code: | SC855-02 |
| Description: | Wireless LAN board error (driver initialization failure) Wireless LAN board error (wireless LAN card: 802.11 is covered) |
| Causes: | • Defective wireless LAN board • Loose connection |
| Remedy: | • Turn the main power OFF/ON. • Replace wireless LAN board |
| Error code: | SC857-00 |
| Description: | USB I/F Error The USB interface is unusable because of a driver error. |
| Causes: | USB driver error (There are three causes of USB error: RX error/CRC error/STALL. SC is issued only in the case of STALL.) |
| Remedy: | • Check USB connection. • Replace the controller board. |
| Error code: | SC858-01 |
| Description: | Data encryption conversion error (HDD Key Setting Error) A serious error occurred during an attempt to update the encryption key. |
| Causes: | • USB Flash, other data, corrupted • Communication error caused by electrostatic noise • Controller board defective |
| Remedy: | • Turn the main power OFF/ON. • If the error persists, replace the controller board. |
| Error code: | SC858-02 |
| Description: | Data encryption conversion error (NVRAM Read/Write Error) A serious error occurred after data conversion during an attempt to update the encryption key. |
| Causes: | NVRAM defective |
| Remedy: | • Replace the NVRAM. • Replace the controller board. |
| Error code: | SC858-30 |
| Description: | Data encryption conversion error (NVRAM Before Replace Error) A serious error occurred after data conversion during an attempt to update the encryption key. |
| Causes: | Software error such as conversion parameters being invalid. |
| Remedy: | • Turn the main power OFF/ON. • If the error persists, replace the controller board. |
| Error code: | SC858-31 |
| Description: | Data encryption conversion error (Other Error) A serious error occurred after data conversion during an attempt to update the encryption key |
| Causes: | Controller board defective |
| Remedy: | Replace the controller board. |
| Error code: | SC859-01 |
| Description: | Data encryption conversion HDD conversion error (HDD check error) When the data encryption key was updated, HDD data was converted, but not correctly. Image displayed at conversion only (this SC is not displayed), but SC is displayed after machine is cycled off/on. |
| Causes: | • HDD conversion was set with the data encryption key update function, but the HDD was removed. • Machine lost power during data encryption key update • Electrostatic noise, or an HDD error occurred, during data encryption key update, and data was not encrypted. |
| Remedy: | • Check HDD connection. • Format the HDD (SP5-832: HDD formatting). • If there is a problem with the HDD, it has to be replaced. |
| Error code: | SC859-02 |
| Description: | Data encryption conversion HDD conversion error (Power failure during conversion) When the data encryption key was updated, HDD data was converted, but not correctly. Image displayed at conversion only (this SC is not displayed), but SC is displayed after machine is cycled off/on. Details: NVRAM/HDD conversion is incomplete. |
| Causes: | Power failure occurred during encryption key update. |
| Remedy: | The display after restart instructs the user to format the HDD. |
| Error code: | SC859-10 |
| Description: | Data encryption conversion HDD conversion error (Data read/write command error) When the data encryption key was updated, HDD data was converted, but not correctly. Image displayed at conversion only (this SC is not displayed), but SC is displayed after machine is cycled off/on. Details: Abnormal DMAC return value has been received two or more times (DMAC timeout, serial communication error etc.) |
| Causes: | HDD was not successfully converted during encryption key update due to HDD errors or cable noises. |
| Remedy: | • Check HDD connection. • Format the HDD (SP5-832: HDD formatting). • If there is a problem with the HDD, it has to be replaced. |
| Error code: | SC860-00 |
| Description: | HDD startup error at main power on (HDD error) • The HDD is connected but the driver detected the following errors. • SS_NO.T_READY:/* (-2)HDD does not become READY*/ • SS_BAD_LABEL:/* (-4)Wrong partition type*/ • SS_READ_ERROR:/* (-5)Error occurred while reading or checking the label*/ • SS_WRITE_ERROR:/* (-6)Error occurred while writing or checking the label*/ • SS_FS_ERROR:/* (-7)Failed to repair the filesystem*/ • SS_MOUNT_ERROR:/* (-8)Failed to mount the filesystem*/ • SS_COMMAND_ERROR:/* (-9)Drive not responding to command*/ • SS_KERNEL_ERROR:/* (-10)Internal kernel error*/ • SS_SIZE_ERROR:/* (-11)Drive size too small*/ • SS_NO._PARTITION:/* (-12)The specified partition does not exist*/ • SS_NO._FILE:/* (-13)Device file does not exist*/ • Attempted to acquire HDD status through the driver but there has been no response for 30 seconds or more. |
| Causes: | • Unformatted HDD • Label data corrupted • HDD defective |
| Remedy: | Format the HDD (SP5-832: HDD formatting) through SP mode. |
| Error code: | SC865-00 |
| Description: | HD access error During HDD operation, the HDD returned an error. |
| Causes: | The HDD returned an error that does not constitute SC863 (bad sector) or SC864 (CRC error). |
| Remedy: | Replace the HDD. |
| Error code: | SC866-00 |
| Description: | SD card authentication error A license error of an application that is started from the SD card was detected. |
| Causes: | Invalid program data is stored on the SD card. |
| Remedy: | Store a valid program data on the SD card. |
| Error code: | SC867-00 |
| Description: | SD card removal detection When an application SD card is removed from the slot while the application is being activated. |
| Causes: | An application SD card has been removed from the slot (from the mount point /mnt/sd0). |
| Remedy: | Turn the main power off/on. |
| Error code: | SC868-00 |
| Description: | SD card access error The SD controller returned an error during operation. (An error occurred at the mount point of /mnt/sd0) |
| Causes: | • SD card is defective • SD controller is defective |
| Remedy: | • Reformat the SD card (using the "SD Formatter" made by Panasonic).* • Check the SD card insertion status. • Replace the SD card. • Replace the controller board. |
| Error code: | SC868-01 |
| Description: | SD card access error The SD controller returned an error during operation. (An error occurred at the mount point of /mnt/sd1) |
| Causes: | • SD card is defective • SD controller is defective |
| Remedy: | SD card used for starting an application • Turn the main power off and check the SD card insertion status. • If no problem is found, insert the SD card and turn the main power on. • If an error occurs, replace the SD card. • SD card for users • In case of a file system error, reformat the SD card (using the "SD Formatter" made by Panasonic).* • In case of a device access error, turn the main power off and check the SD card insertion status. • If no problem is found, insert the SD card and turn the main power on. • If an error occurs, use another SD card. • If the error persists even after replacing the SD card, replace the controller board. |
| Error code: | SC868-02 |
| Description: | SD card access error The SD controller returned an error during operation. (An error occurred at the mount point of /mnt/sd1) |
| Causes: | • SD card defective • SD controller defective |
| Remedy: | SD card that starts an application • Turn the main power off and check the SD card insertion status. • If no problem is found, insert the SD card and turn the main power on. • If an error occurs, replace the SD card. • SD card for users • In case of a file system error, reformat the SD card (using the "SD Formatter" made by Panasonic).* • In case of a device access error, turn the main power off and check the SD card insertion status. • If no problem is found, insert the SD card and turn the main power on. • If an error occurs, use another SD card. • If the error persists even after replacing the SD card, replace the controller board. |
| Error code: | SC870 |
| Description: | Address book data error. Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Software bug • Inconsistency of Address Book source location (machine/delivery server/LDAP server) • Inconsistency of Address Book encryption setting or encryption key (NVRAM was replaced individually without formatting the Address Book) • Address Book storage device (SD) was temporarily removed or hardware configuration does not match the application configuration. • Address Book data corruption was detected. |
| Remedy: | • Software defective. Turn the machine OFF/ON. If this is not the solution for the problem, then replace the controller firmware. • HDD defective. More Details • Do SP5846 050 (UCS (User info control service) Settings – Initialize all Directory Info.) to reset all address book data. • Reset the user information with SP5832 006 (HDD Formatting– User Information). • Replace the HDDs. • Boot the machine from the SD card. |
| Error code: | SC872-00 |
| Description: | HDD mail reception error An error was detected on the HDD immediately after the machine was turned on. |
| Causes: | • HDD defective • Power was turned off while the machine used the HDD. |
| Remedy: | • Format the HDD (SP5-832-007: HDD Formatting: Mail RX Data).). • Replace the HDD. When you do the above, the following information will be initialized. • Partly received partial mail messages. • Already-read statuses of POP3-received messages (All messages on the mail server are handled as new messages). |
| Error code: | SC873-00 |
| Description: | HDD mail reception error An error was detected on the HDD immediately after the machine was turned on. |
| Causes: | • HDD defective • Power was turned off while the machine used the HDD. |
| Remedy: | • Format the HDD (SP5-832-007 : HDD Formatting: Mail RX Data). • Replace the HDD. When you do the above, the following information will be initialized. • Sender’s mail text • Default sender name/password (SMB/FTP/NCP) • Administrator mail address • Scanner delivery history |
| Error code: | SC875-01 |
| Description: | Delete all error (HDD erasure) (hddchack –i error) An error was detected before HDD/data erasure starts. (Failed to erase data/failed to logically format HDD) |
| Causes: | • HDD logical formatting failed. • The modules failed to erase data. |
| Remedy: | Turn the main power OFF/ON. |
| Error code: | SC875-02 |
| Description: | Delete all error (HDD erasure) (Data deletion failure) An error was detected before HDD/data erasure starts. (Failed to erase data/failed to logically format HDD) |
| Causes: | • HDD logical formatting failed. • The modules failed to erase data. |
| Remedy: | Turn the main power OFF/ON. |
| Error code: | SC876-01 |
| Description: | Log Data Error 1 An error was detected in the handling of the log data at power on or during machine operation. |
| Causes: | Damaged log data file |
| Remedy: | Initialize the HDD (SP5-832-004). |
| Error code: | SC876-02 |
| Description: | Log Data Error 2 An error was detected in the handling of the log data at power on or during machine operation. |
| Causes: | Log encryption is enabled but encryption module is not installed. |
| Remedy: | • Replace or set again the encryption module. • Disable the log encryption setting. |
| Error code: | SC876-03 |
| Description: | Log Data Error 3 An error was detected in the handling of the log data at power on or during machine operation. |
| Causes: | Inconsistency of encryption key between NV-RAM and HDD. |
| Remedy: | • Disable the log encryption setting. • Initialize LCS memory (SP5801-019). • Initialize the HDD (SP5-832-004). |
| Error code: | SC876-04 |
| Description: | Log Data Error 4 An error was detected in the handling of the log data at power on or during machine operation. |
| Causes: | • Log encryption key is disabled but the log data file is encrypted. (NVRAM data corruption) • Log encryption key is enabled but the log data file is not encrypted. (NVRAM data corruption) |
| Remedy: | Initialize the HDD (SP5-832-004). |
| Error code: | SC876-05 |
| Description: | Log Data Error 5 An error was detected in the handling of the log data at power on or during machine operation. |
| Causes: | • Only the NV-RAM has been replaced with one previously used in another machine. • Only the HDD has been replaced with one previously used in another machine. |
| Remedy: | • Attach the original NV-RAM. • Attach the original HDD. • With the configuration that caused the SC, initialize the HDD (SP5-832-004). |
| Error code: | SC876-99 |
| Description: | Log Data Error 99 An error was detected in the handling of the log data at power on or during machine operation. |
| Causes: | Other causes |
| Error code: | SC877-00 |
| Description: | Data Overwrite Security card error The "Auto Erase Memory" function of the Data Overwrite Security is set to on but it cannot be done. |
| Causes: | • Data Overwrite Security option SD card is broken. • Data Overwrite Security option SD card has been removed. |
| Remedy: | • If the SD card is broken, prepare a new Data Overwrite Security option SD card and replace the NVRAM. • If the SD card has been removed, turn the main power off and reinstall a working Data Overwrite Security option SD card. |
| Error code: | SC880-00 |
| Description: | MLB error |
| Causes: | The response is not received within the specified time during the access to the MLB. Defective MLB |
| Remedy: | • Replace the MLB • Remove the MLB |
| Error code: | SC881-01 |
| Description: | Management area error • A problem was detected in the software • This error may even occur is an IC card option is not installed. |
| Causes: | • This is caused by accumulation of abnormal authentication information in the software. (User operation will not directly cause it.) • At login Example: When a job is sent to the printer/when logged on from the operation panel/when logged on from a Web browser |
| Remedy: | Turn the main power off/on. |
| Error code: | SC899-00 |
| Description: | Software performance error (signal reception end) Unknown software error occurred. |
| Causes: | Occurs when an internal program behaves abnormally. |
| Remedy: | In the case of a hardware defect • Replace the hardware. In the case of a software error • Turn the main power OFF/ON. • Try updating the firmware. |
| Error code: | SC900-00 |
| Description: | Electric counter error The electric total counter value is out of specification. Error is detected when increasing the total counter. |
| Causes: | • Unexpected NV-RAM is attached. • NV-RAM defective • NV-RAM data corrupted. • Data written to unexpected area because of external factor etc. • The count requested by the SRM on receiving PRT is not completed. |
| Remedy: | Replace the NV-RAM. |
| Error code: | SC901 |
| Description: | Mechanical Counter 1 error Mechanical Counter 1 was not set correctly at power on, or the operator disconnected the counter while machine was operating. |
| Causes: | • Mechanical Counter 1 connection loose or defective • Mechanical Counter 1 defective |
| Error code: | SC920 |
| Description: | Printer error 1. An internal application error was detected and operation cannot continue. |
| Causes: | • The software’s bug • Unexpected hardware configuration such as insufficient memory |
| Remedy: | • Software defective; turn the machine OFF/ON, or change the controller firmware • Insufficient memory |
| Error code: | SC921-00 |
| Description: | Printer application error (Resident font not found) The resident fonts cannot be found at printer startup. |
| Causes: | The resident font file is missing. |
| Remedy: | Turn the main power off/on. |
| Error code: | SC925 |
| Description: | Net File function error. The NetFile file management on the HDD cannot be used, or a NetFile management file is corrupted and operation cannot continue. The HDDs are defective and they cannot be debugged or partitioned, so the Scan Router functions (delivery of received faxes, document capture, etc.), Web services, and other network functions cannot be used. HDD status codes are displayed below: |
| Causes: | The NetFile file management on the HDD cannot be used, or a NetFile management file is corrupted and operation cannot continue. The HDDs are defective and they cannot be debugged or partitioned, so the Scan Router functions (delivery of received faxes, document capture, etc.), Web services, and other network functions cannot be used. HDD status codes are displayed below the SC code: |
| Remedy: | Procedure 1 If the machine shows SC codes for HDD errors (SC860 ~ SC865) with SC 925, do the recovery procedures for SC860 ~ SC865. Procedure 2 If the machine does not show one of the five HDD errors (SC860 ~ SC865), turn the machine power OFF and ON. If this is not the solution for the problem, then initialize the NetFile partition on the HDD with SP5832-011 (HDD Formatting). NetFiles: Jobs printed from the document server using a PC and DeskTopBinder • Before you initialize the NetFile partition on the HDD, tell the customer that: • Received faxes on the delivery server will be erased • All captured documents will be erased • DeskTopBinder job history will be erased • Documents on the document server, and scanned documents, will not be erased. • The first time that the network gets access to the machine, the management information must be configured again (this will use a lot of time). Before you initialize the Netfile partition with SP5832-011, do these steps: 1. Go into the User Tools mode and do “Delivery Settings” to print all received fax documents that are scheduled for delivery. Then erase them. 2. In the User Tools mode, do Document Management> Batch Delete Transfer Documents. 3. Do SP5832-011, then turn the machine power OFF and ON. Procedure 3 If “Procedure 2” is not the solution for the problem, do SP5832-001 (HDD Formatting – All), then turn the machine power OFF and ON. SP5832-001 erases all document and address book data on the hard disks. Ask the customer before you do this SP code. Procedure 4 If “Procedure 3” is not the solution for the problem, replace the HDD. |
| Error code: | SC990-00 |
| Description: | Software operation error Software attempted an unexpected operation. |
| Causes: | • Parameter error • Internal parameter error • Insufficient work memory • Operation error caused by abnormalities that are normally undetectable. |
| Remedy: | • Turn the main power off/on. • Reinstall the software of the controller and BCU board. |
| Error code: | SC991-00 |
| Description: | Recoverable software operation error Software attempted an unexpected operation. SC991 covers recoverable errors as opposed toCS990. |
| Causes: | • Parameter error • Internal parameter error • Insufficient work memory • Operation error caused by abnormalities that are normally undetectable. |
| Remedy: | Logging only |
| Error code: | SC992-00 |
| Description: | Undefined SC issued. An SC, that is not controlled by the system, occurred. |
| Causes: | • An SC for the previous model was used mistakenly, etc. • Basically a software bug. |
| Remedy: | Turn the main power OFF/ON. |
| Error code: | SC995-01 |
| Description: | CPM setting error 1 Comparison of machine serial number (11 digits) and machine identification code. Details: • Machine serial number cannot be identified because of BICU replacement or malfunctioning. • Machine serial number cannot be identified because of NV-RAM replacement |
| Causes: | Machine serial number (11 digits) or machine identification code does not match. |
| Remedy: | • Enter the machine serial number using SP5-811 (MachineSerial), and then turn the power on/off. • Attach the NV-RAM that was installed previously. |
| Error code: | SC995-02 |
| Description: | CPM setting error 2 Comparison of machine serial number (11 digits) and machine identification code. Details: Machine serial number cannot be identified because of NV-RAM replacement or malfunctioning. |
| Causes: | Machine serial number (11 digits) or machine identification code does not match. |
| Remedy: | • Attach the NV-RAM that was installed previously. • Download data on the NV-RAM using SP5-825 (NV-RAM Data Download). |
| Error code: | SC995-03 |
| Description: | CPM setting error 3 Comparison of machine serial number (11 digits) and machine identification code. Details: Unable to recognize machine identification code because the controller was replaced incorrectly or is malfunctioning. |
| Causes: | Machine serial number (11 digits) or machine identification code does not match. |
| Remedy: | Replace it with the correct type of controller. |
| Error code: | SC995-04 |
| Description: | CPM setting error 4 Comparison of machine serial number (11 digits) and machine identification code. |
| Causes: | Machine serial number (11 digits) or machine identification code does not match. |
| Remedy: | Return the parts to the original configuration, and then replace them according to the manual |
| Error code: | SC997-00 |
| Description: | Application function selection error The application selected by the operation panel key operated abnormally (No response, abnormal ending). |
| Causes: | Software bug (mainly the application) |
| Remedy: | • Check the optional RAM, DIMM, boards required by the application program. • Check if the combination of downloaded programs are correct. |
| Error code: | SC998-00 |
| Description: | Application start error • No application was registered to system within a specified time after the main power was turned on. (No application starts/All applications have been terminated abnormally) • Application started but cannot be drawn now for some reason. |
| Causes: | • Software bug (mainly the application) • The optional RAM, DIMM, boards required by the application program. Are not installed correctly. |
| Remedy: | • Turn the main power OFF/ON. • Check the optional RAM, DIMM, boards • Check the combination of programs • Replace the controller board. |
Парткод
Название
RICOH TYPE 2220D/2320D Тонер-картридж
