Ricoh MP2580
Рейтинг
Модули
DUPLEX UNIT 1 (D010/D043)
DUPLEX UNIT 2 (D010/D043)
PCU 1 (D010/D043)
ELECTRICAL SECTION 2 (D010/D043)
FUSING UNIT (D010/D043)
BY-PASS FEED SECTION (D010/D043)
OPTICS SECTION 2 (D010/D043)
EXTERIOR 2 (D010/D043)
OPTICS SECTION 1 (D010/D043)
EXTERIOR 1 (D010/D043)
DRIVE SECTION 2 (D010/D043)
DRIVE SECTION 3 (D010/D043)
ELECTRICAL SECTION 1 (D010/D043)
PCU 2 (D010/D043)
2ND PAPER FEED SECTION 2 (D010/D043)
OPTICS SECTION 3 (D010/D043)
2nd PAPER TRAY (D010/D043)
LASER UNIT (D010/D043)
GDI UNIT (D010/D043)
DRIVE SECTION 1 (D010/D043)
TONER SUPPLY UNIT (D010/D043)
PAPER EXIT SECTION (D010/D043)
1st PAPER TRAY (D010/D043)
PAPER RESISTRATION (D010/D043)
2ND PAPER FEED SECTION 1 (D010/D043)
DUPLEX UNIT 3 (D010/D043)
OPERATION PANEL (D010/D043)
1ST PAPER FEED SECTION (D010/D043)
Детали LASER UNIT (D010/D043)
| Деталь: | Vertical Transport Roller |
| Парткод: | D010 4603 |
| Деталь: | BUSHING - VERTICAL TRANSPORT |
| Парткод: | AA08 0268 |
| Деталь: | Spring - Vertical Transport |
| Парткод: | AA06 3399 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | B039 2558 |
| Деталь: | Guide Plate - Vertical Transport |
| Парткод: | D010 4662 |
| Деталь: | Bracket - Duplex Entrance Sensor |
| Парткод: | B043 4676 |
| Деталь: | Transport Driven Roller - Middle |
| Парткод: | G060 2641 |
| Деталь: | Driven Roller Bushing |
| Парткод: | AA08 0313 |
| Деталь: | Lower Spring Plate - Driven Roller |
| Парткод: | B043 4647 |
| Деталь: | Exit Duplex Sensor Bracket |
| Парткод: | B123 4675 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0181 |
| Деталь: | Duplex Gide Plate |
| Парткод: | D010 4640 |
| Деталь: | Right Lower Exit Guide Plate Assy |
| Парткод: | B123 4670 |
| Деталь: | Spring - 2N |
| Парткод: | B043 4645 |
| Деталь: | Upper Spring Plate - Driven Roller |
| Парткод: | B043 4646 |
| Деталь: | Door lever |
| Парткод: | B043 4651 |
| Деталь: | SPRING |
| Парткод: | A250 1388 |
| Деталь: | Bracket - Upper Guide Plate |
| Парткод: | B043 4671 |
| Деталь: | Exit Sensor Cover |
| Парткод: | B123 4679 |
| Деталь: | Cover - Duplex Entrance Sensor |
| Парткод: | B043 4674 |
| Деталь: | Right Upper Exit Guide Plate Assy |
| Парткод: | B123 4977 |
| Деталь: | Entrance Duplex Guide Plate |
| Парткод: | B123 4617 |
| Деталь: | Decal |
| Парткод: | B123 4691 |
| Деталь: | Ground Wire - Duplex |
| Парткод: | D010 5245 |
| Деталь: | Grip Decal |
| Парткод: | B043 4692 |
| Деталь: | Stopper - Guide Plate |
| Парткод: | B043 4642 |
| Деталь: | Stepped Screw - M5 |
| Парткод: | B039 4480 |
| Деталь: | Guide:Vertical Transport:NO2 |
| Парткод: | D010 4672 |
| Деталь: | Guide:Vertical Transport:NO3 |
| Парткод: | D010 4673 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Duplex Lower Stay |
| Парткод: | B043 4609 |
| Деталь: | Stepper Motor - DC |
| Парткод: | D010 4710 |
| Деталь: | By-pass Feed Guide - Lower |
| Парткод: | B043 4667 |
| Деталь: | Spring - 2.8n |
| Парткод: | B043 4685 |
| Деталь: | SEPARATION PAD |
| Парткод: | B261 4650 |
| Деталь: | Transport Roller:Drive:Duplex:Exit |
| Парткод: | B261 4624 |
| Деталь: | Transport Roller - Connecting |
| Парткод: | B261 4623 |
| Деталь: | Transport Roller:Drive:Duplex:Entrance |
| Парткод: | B261 4625 |
| Деталь: | By-pass Feed Guide - Upper |
| Парткод: | B043 4684 |
| Деталь: | Bracket - Paper End Sensor |
| Парткод: | B039 2610 |
| Деталь: | Relay Harness - Paper End Sensor |
| Парткод: | D010 5252 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | B039 2611 |
| Деталь: | Spring - Paper End Sensor |
| Парткод: | AA06 6343 |
| Деталь: | By-pass Feed Roller |
| Парткод: | AF03 1060 |
| Деталь: | Manual Feed Drive Shaft |
| Парткод: | B261 4686 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Pulley - 30Z |
| Парткод: | B043 4624 |
| Деталь: | Timing Belt - 40S2M290 |
| Парткод: | B123 4505 |
| Деталь: | Pulley - 30T |
| Парткод: | AB03 0569 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Rear Inner Cover - Duplex |
| Парткод: | D010 4661 |
| Деталь: | Gear - 25Z |
| Парткод: | B043 4714 |
| Деталь: | Gear - 22Z |
| Парткод: | B043 4633 |
| Деталь: | Gear - 25Z |
| Парткод: | B043 4713 |
| Деталь: | Gear - 38Z |
| Парткод: | B043 4631 |
| Деталь: | Tension Spring 27n |
| Парткод: | B123 4697 |
| Деталь: | Duplex Cover |
| Парткод: | D010 4627 |
| Деталь: | Relay Harness - Duplex Unit |
| Парткод: | D010 5241 |
| Деталь: | Coupled Gear 25/59Z |
| Парткод: | B043 4632 |
| Деталь: | MOTOR BRACKET |
| Парткод: | D010 4705 |
| Деталь: | Duplex Unit Stopper Assy |
| Парткод: | B123 4693 |
| Деталь: | Chain Bracket |
| Парткод: | B043 4694 |
| Деталь: | Cap - 30x36 |
| Парткод: | B043 4698 |
| Деталь: | Side Plate:Drive:Assy |
| Парткод: | D010 4613 |
| Деталь: | Pad:13X26 |
| Парткод: | B043 4688 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Nylon Clamp - 5n |
| Парткод: | 11 050 009 |
| Деталь: | Pan Self-tapping Screw:3x6 |
| Парткод: | 0433 0060N |
| Деталь: | Rear Drum Stay |
| Парткод: | B259 2371 |
| Деталь: | Development Joint |
| Парткод: | A267 3440 |
| Деталь: | Front Side Plate - Drum |
| Парткод: | B039 2361 |
| Деталь: | Drum Shutter Spring |
| Парткод: | B039 2367 |
| Деталь: | Drum Shutter Gear |
| Парткод: | B039 2362 |
| Деталь: | Development Roller Assy |
| Парткод: | B259 3051 |
| Деталь: | Case:Development:Upper:Assy |
| Парткод: | B259 3200 |
| Деталь: | Development Case Assy |
| Парткод: | B259 3170 |
| Деталь: | Idler Gear - 16z |
| Парткод: | B039 3062 |
| Деталь: | Density Sensor:K-C2.5:Assy |
| Парткод: | B259 3390 |
| Деталь: | Gear - 15Z |
| Парткод: | B039 3245 |
| Деталь: | Development Roller Gear |
| Парткод: | B039 3060 |
| Деталь: | Developer Type 28 Black |
| Парткод: | B121 9640 |
| Деталь: | Developer Type 28 Black - NA EU |
| Парткод: | B121 9645 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | PCU - Assy |
| Парткод: | B259 2210 |
| Деталь: | Harness - Document Feeder |
| Парткод: | D010 5240 |
| Деталь: | ADF Plug Bracket |
| Парткод: | D010 5831 |
| Деталь: | Stepper Motor - DC |
| Парткод: | D010 4710 |
| Деталь: | Stepper Motor Bracket |
| Парткод: | B261 4994 |
| Деталь: | Coupled Gear - 15/51Z |
| Парткод: | B043 4991 |
| Деталь: | Bracket:C |
| Парткод: | D010 1016 |
| Деталь: | Harness - 1-bin Tray |
| Парткод: | D010 5255 |
| Деталь: | Fan Motor - DC 2.88w |
| Парткод: | D010 1106 |
| Деталь: | Fan motor bracket |
| Парткод: | D010 1102 |
| Деталь: | High Voltage Cable |
| Парткод: | D010 5232 |
| Деталь: | Harness:Motor:Main |
| Парткод: | D010 5203 |
| Деталь: | Power Pack |
| Парткод: | D010 5710 |
| Деталь: | Harness:Ground Wire |
| Парткод: | D010 5219 |
| Деталь: | Bracket - Power Pack |
| Парткод: | D010 5841 |
| Деталь: | Stay:Scanner:Right Lower |
| Парткод: | D010 1014 |
| Деталь: | Stopper:Lever:Door:Right |
| Парткод: | D010 1073 |
| Деталь: | Supporting Plate:Frame:C |
| Парткод: | D010 1081 |
| Деталь: | Front Main Duct |
| Парткод: | D010 1110 |
| Деталь: | Rear Main Duct |
| Парткод: | D010 1111 |
| Деталь: | Tapping Screw:M3x33 |
| Парткод: | B259 1119 |
| Деталь: | Spacer:Lock:KGLS-12RT |
| Парткод: | G020 5871 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Screw - M3X6 |
| Парткод: | 0313 0060N |
| Деталь: | Tapping Screw:3x30 |
| Парткод: | 0451 3030N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | Fusing Unit - 115v |
| Парткод: | D010 4001 |
| Деталь: | Fusing Unit - 230V |
| Парткод: | D010 4002 |
| Деталь: | Fusing Exit Guide |
| Парткод: | B039 4102 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3870 |
| Деталь: | THERMISTOR |
| Парткод: | AW10 0073 |
| Деталь: | Front Ground Plate |
| Парткод: | B039 4118 |
| Деталь: | THERMOSTAT |
| Парткод: | B039 4120 |
| Деталь: | Fusing Cleaning Roller |
| Парткод: | B259 4015 |
| Деталь: | Spur |
| Парткод: | A232 2374 |
| Деталь: | Stripper Pawl Spring |
| Парткод: | AA06 6637 |
| Деталь: | Stripper Pawls |
| Парткод: | AE04 4062 |
| Деталь: | Front Electrode Plate |
| Парткод: | B121 4111 |
| Деталь: | Thermostat Assy |
| Парткод: | B121 4120 |
| Деталь: | Short Electrode Plate |
| Парткод: | B121 4113 |
| Деталь: | Long Electrode Plate |
| Парткод: | B121 4112 |
| Деталь: | Rear Electrode Plate |
| Парткод: | B121 4114 |
| Деталь: | Rear Heater Holder |
| Парткод: | B259 4091 |
| Деталь: | Heater - 120v,600w |
| Парткод: | D010 4105 |
| Деталь: | Heater - 230v, 600w |
| Парткод: | D010 4107 |
| Деталь: | External Circlip |
| Парткод: | G029 4140 |
| Деталь: | Gear - 41Z |
| Парткод: | B039 4171 |
| Деталь: | Bearing 30x42x7 |
| Парткод: | G052 4618 |
| Деталь: | Hot Roller Mm30 |
| Парткод: | AE01 1113 |
| Деталь: | Front Heater Holder |
| Парткод: | B121 4090 |
| Деталь: | Pressure Roller:Dia30 |
| Парткод: | D010 4071 |
| Деталь: | Fusing Exit Guide |
| Парткод: | D010 4072 |
| Деталь: | Spring - Fusing Exit Guide |
| Парткод: | AA06 6635 |
| Деталь: | Pressure Roller Lever |
| Парткод: | B039 4135 |
| Деталь: | PRESSURE SPRING |
| Парткод: | D010 4070 |
| Деталь: | Pressure Roller Bushing |
| Парткод: | G029 4174 |
| Деталь: | Fusing Unit Frame |
| Парткод: | D010 4053 |
| Деталь: | Stripper Pawls Roller |
| Парткод: | B039 4170 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | B259 4115 |
| Деталь: | Discharge Brush |
| Парткод: | B039 4117 |
| Деталь: | Rear Ground Plate |
| Парткод: | B039 4114 |
| Деталь: | Stripper Pawlsstopper |
| Парткод: | B039 4168 |
| Деталь: | Heater - 120v,650w |
| Парткод: | D010 4106 |
| Деталь: | Heater - 230v,650w |
| Парткод: | D010 4108 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 3570 |
| Деталь: | Bushing - Fusing Cleaning Roller |
| Парткод: | D010 4073 |
| Деталь: | Frame:Fusing |
| Парткод: | B121 4103 |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 8 046 123 |
| Деталь: | Screw:Polished Round/Spring:M3x10 |
| Парткод: | 0954 3010N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Screw - M3X6 |
| Парткод: | 0313 0060N |
| Деталь: | Manual Feed Unit:Assy |
| Парткод: | D010 2602 |
| Деталь: | Front Side Fence |
| Парткод: | B039 2631 |
| Деталь: | Bottom Plate Pad |
| Парткод: | B039 2628 |
| Деталь: | Rear Side Fence |
| Парткод: | B039 2632 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B039 2630 |
| Деталь: | Rack - Rear Side Fence |
| Парткод: | B039 2638 |
| Деталь: | Rack - Front Side Fence |
| Парткод: | B039 2637 |
| Деталь: | SIDE FENCE GEAR |
| Парткод: | G012 3050 |
| Деталь: | Spring - By-pass Feed Table |
| Парткод: | AA06 3643 |
| Деталь: | Paper size sensor |
| Парткод: | AW50 0034 |
| Деталь: | Stay - Tray Bottom Plate |
| Парткод: | B039 2629 |
| Деталь: | Paper Guide - Extension |
| Парткод: | B039 2620 |
| Деталь: | PAPER GUIDE |
| Парткод: | B039 2621 |
| Деталь: | Magnet Catch - By-pass Feed |
| Парткод: | B121 2617 |
| Деталь: | By-pass Feed Table |
| Парткод: | B039 2619 |
| Деталь: | Lever - By-pass Feed Table |
| Парткод: | G020 2784 |
| Деталь: | Link - By-pass Feed Table |
| Парткод: | B039 2643 |
| Деталь: | Decal - By-pass Feed |
| Парткод: | B039 2633 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Pin - Mm6 |
| Парткод: | B259 2642 |
| Деталь: | LEVER SHAFT |
| Парткод: | B259 2786 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | 2nd Mirror |
| Парткод: | B039 1787 |
| Деталь: | 2nd Mirror Holder |
| Парткод: | B039 1781 |
| Деталь: | SCANNER DRIVE PULLEY |
| Парткод: | B039 1785 |
| Деталь: | Flexible Board Guide |
| Парткод: | B121 1782 |
| Деталь: | Carriage No.2 Assy |
| Парткод: | B259 1768 |
| Деталь: | Scanner drive belt |
| Парткод: | B039 1784 |
| Деталь: | Idler Belt Pulley Bracket - Rear |
| Парткод: | B259 1778 |
| Деталь: | TENSION SPRING |
| Парткод: | B039 1790 |
| Деталь: | Idler Belt Pulley Bracket - Front |
| Парткод: | B259 1776 |
| Деталь: | Xenon Lamp:Assy |
| Парткод: | D010 1791 |
| Деталь: | Timing Belt Holder - Front |
| Парткод: | B039 1758 |
| Деталь: | 1st Scanner Unit |
| Парткод: | D010 1751 |
| Деталь: | Timing Belt Holder - Rear |
| Парткод: | B039 1759 |
| Деталь: | No.1 Mirror Clamp |
| Парткод: | B121 1766 |
| Деталь: | No.1 Mirror |
| Парткод: | B121 1762 |
| Деталь: | Xenon Lamp Stabilizer |
| Парткод: | D010 1763 |
| Деталь: | Harness - Lamp Stabilizer |
| Парткод: | D010 5223 |
| Деталь: | Slider - Scanner |
| Парткод: | G570 2730 |
| Деталь: | Guide:Harness:Scanner |
| Парткод: | B121 1816 |
| Деталь: | Guide Mylar |
| Парткод: | B121 5822 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw:3X6 |
| Парткод: | 0451 3006N |
| Деталь: | Left Cover - NA |
| Парткод: | D010 1316 |
| Деталь: | Left Cover - EU |
| Парткод: | D010 1315 |
| Деталь: | Rail - Reverser Shelf |
| Парткод: | B043 4998 |
| Деталь: | Exit Tray - NA |
| Парткод: | D010 1356 |
| Деталь: | Exit Tray - EU |
| Парткод: | D010 1357 |
| Деталь: | Knob Screw:M3 |
| Парткод: | G104 5141 |
| Деталь: | Rear Cover - NA |
| Парткод: | D010 1246 |
| Деталь: | Rear Cover - EU |
| Парткод: | D010 1249 |
| Деталь: | Cap - Application |
| Парткод: | D010 1314 |
| Деталь: | Cap - IC Card |
| Парткод: | D010 1313 |
| Деталь: | Cap - Paper Bank |
| Парткод: | D010 1349 |
| Деталь: | Right Rear Cover - NA |
| Парткод: | D010 1347 |
| Деталь: | Right Rear Cover - EU |
| Парткод: | D010 1346 |
| Деталь: | Right Front Cover - 2nd Tray |
| Парткод: | D010 2731 |
| Деталь: | Right Front Cover - Upper NA |
| Парткод: | D010 1310 |
| Деталь: | Right Front Cover - Upper EU |
| Парткод: | D010 1309 |
| Деталь: | Front Door - EU |
| Парткод: | D010 1350 |
| Деталь: | Front Cover - NA |
| Парткод: | D010 1351 |
| Деталь: | Main Switch Cover |
| Парткод: | B039 1362 |
| Деталь: | Cover Magnet |
| Парткод: | B039 1366 |
| Деталь: | Sheet:Operation Instructions |
| Парткод: | B039 1365 |
| Деталь: | MAGNET CATCH |
| Парткод: | B039 1361 |
| Деталь: | Front Door (NA) |
| Парткод: | D010 1338 |
| Деталь: | Front Door - EU |
| Парткод: | D010 1308 |
| Деталь: | Model Name Plate:D010:GES:AA |
| Парткод: | D010 7410 |
| Деталь: | Model Name Plate:D010:LAN |
| Парткод: | D010 7424 |
| Деталь: | Model Name Plate:D010:RIC |
| Парткод: | D010 7427 |
| Деталь: | Model Name Plate:D010:SVN |
| Парткод: | D010 7411 |
| Деталь: | Model Name Plate:D010:GES:NA |
| Парткод: | D010 7412 |
| Деталь: | Model Name Plate:D010:GES |
| Парткод: | D010 7420 |
| Деталь: | Model Name Plate:D010:NAS |
| Парткод: | D010 7421 |
| Деталь: | Model Name Plate:D010:REX |
| Парткод: | D010 7422 |
| Деталь: | Model Name Plate:D010:INF |
| Парткод: | D010 7426 |
| Деталь: | Panel:Logo |
| Парткод: | B132 1531 |
| Деталь: | Rivet - M6 |
| Парткод: | B039 1367 |
| Деталь: | Rivet - M7 |
| Парткод: | B039 1364 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Shaft:Scale |
| Парткод: | B390 1759 |
| Деталь: | Scale - Left |
| Парткод: | B268 1749 |
| Деталь: | Left Scanner Bracket |
| Парткод: | B039 1710 |
| Деталь: | Photointerruptor:Ee-sx4235a-p2 |
| Парткод: | AW02 0156 |
| Деталь: | Scanner Home Sensor Stopper |
| Парткод: | A193 1793 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Heater - 9W (120V) |
| Парткод: | D010 7009 |
| Деталь: | Heater - 9W (230V) |
| Парткод: | D010 7019 |
| Деталь: | Lens Unit Cover |
| Парткод: | D010 1808 |
| Деталь: | Lens Unit |
| Парткод: | D010 1812 |
| Деталь: | Exposure Glass |
| Парткод: | A250 1752 |
| Деталь: | Scale - Inner Back |
| Парткод: | B268 1751 |
| Деталь: | Bracket - Operation Panel |
| Парткод: | B039 1666 |
| Деталь: | Harness - FFC |
| Парткод: | D010 1804 |
| Деталь: | Right Scanner Bracket |
| Парткод: | B039 1712 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 54 421 924 |
| Деталь: | Rear Scale Bracket |
| Парткод: | B039 1658 |
| Деталь: | Support Bracket |
| Парткод: | D010 1069 |
| Деталь: | ADF Bracket |
| Парткод: | B039 1068 |
| Деталь: | Box Holder |
| Парткод: | B122 5821 |
| Деталь: | Bracket:Connector:Joint Unit |
| Парткод: | D010 5861 |
| Деталь: | Joint Unit Harness |
| Парткод: | D010 5207 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Tray:Exit |
| Парткод: | D010 1284 |
| Деталь: | Exit Cover - Na |
| Парткод: | D010 1354 |
| Деталь: | Exit Cover - Eu |
| Парткод: | D010 1353 |
| Деталь: | Left Scanner Cover - NA |
| Парткод: | D010 1332 |
| Деталь: | Left Scanner Cover - EU |
| Парткод: | D010 1302 |
| Деталь: | Rear Scanner Cover (EU) |
| Парткод: | B039 1303 |
| Деталь: | Cover:Scanner:Rear:NA |
| Парткод: | B276 1333 |
| Деталь: | Right Scanner Cover NA |
| Парткод: | D010 1335 |
| Деталь: | Right Scanner Cover - EU |
| Парткод: | D010 1304 |
| Деталь: | Duct Seal - Exit |
| Парткод: | D010 1109 |
| Деталь: | Duct Cover |
| Парткод: | D010 1112 |
| Деталь: | Duct Seal - Guide |
| Парткод: | D010 1107 |
| Деталь: | Rear Exit Cover - NA |
| Парткод: | D010 1370 |
| Деталь: | Rear Exit Covfer - EU |
| Парткод: | D010 1369 |
| Деталь: | Sorter Cover - NA |
| Парткод: | D010 1372 |
| Деталь: | Soter Cover - EU |
| Парткод: | D010 1371 |
| Деталь: | Fusing Exit Cover |
| Парткод: | D010 1301 |
| Деталь: | Sheet:Accessory:Safety:EU:RAI |
| Парткод: | A232 8561 |
| Деталь: | Panel:Logo |
| Парткод: | B132 1531 |
| Деталь: | Operating Instructions - System NA |
| Парткод: | D010 6507 |
| Деталь: | Operating Instructions - System EU |
| Парткод: | D010 6500 |
| Деталь: | Operating Instructions - Copy NA |
| Парткод: | D010 6607 |
| Деталь: | Operating Instructions - Copy EU |
| Парткод: | D010 6600 |
| Деталь: | Rivet - M6 |
| Парткод: | B039 1367 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Housing - Paper Feed |
| Парткод: | D010 1142 |
| Деталь: | Magnetic Clutch:Manual Feed:0.25N.M |
| Парткод: | D010 2618 |
| Деталь: | Timing Belt - S3M,315 |
| Парткод: | D010 2631 |
| Деталь: | Pulley - 26T |
| Парткод: | D010 1195 |
| Деталь: | Magnetic clutch |
| Парткод: | D010 2616 |
| Деталь: | Magnetic clutch |
| Парткод: | D010 2617 |
| Деталь: | TIMING PULLEY - 18T |
| Парткод: | AB03 0627 |
| Деталь: | Bracket:Tension |
| Парткод: | B090 2602 |
| Деталь: | Spring:Tension |
| Парткод: | B091 2615 |
| Деталь: | Gear - 67Z/41Z |
| Парткод: | D010 1196 |
| Деталь: | Pulley - 26T |
| Парткод: | D010 1193 |
| Деталь: | Gear - 84Z/65Z |
| Парткод: | D010 1191 |
| Деталь: | Guard:Drive:Paper Feed:Right |
| Парткод: | D010 2592 |
| Деталь: | Cover:Positioning Pin:Left Inner Rear |
| Парткод: | B090 2593 |
| Деталь: | Snap Ring |
| Парткод: | B091 2607 |
| Деталь: | Magnetic clutch |
| Парткод: | D010 2618 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Bushing:DIA6 |
| Парткод: | 8 053 480 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Tapping Screw:Washer:3X8 |
| Парткод: | 8 025 299 |
| Деталь: | Retaining Rings-E:6 |
| Парткод: | 7 200 060 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 8 025 299 |
| Деталь: | DC Motor:Paper Feed:Assy |
| Парткод: | AX04 0220 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Bushing - 8x16x7 |
| Парткод: | AA08 2070 |
| Деталь: | Bracket:Rise:2 |
| Парткод: | B090 2773 |
| Деталь: | Bracket:Lever:Pressure |
| Парткод: | B090 2781 |
| Деталь: | Rising Unit:Assy |
| Парткод: | B209 2780 |
| Деталь: | Pressure Lever Stopper |
| Парткод: | B024 2765 |
| Деталь: | Tension Spring:Stopper:Return |
| Парткод: | B091 2766 |
| Деталь: | Sub Pressure Lever |
| Парткод: | A267 2794 |
| Деталь: | Shutter - Photointerruptor |
| Парткод: | A267 2849 |
| Деталь: | Stopper:Holder:Compression Spring |
| Парткод: | B090 2848 |
| Деталь: | Lever:DC Motor |
| Парткод: | B090 2776 |
| Деталь: | Bushing - Motor Shaft |
| Парткод: | A267 2847 |
| Деталь: | Holder - Spring |
| Парткод: | A267 2846 |
| Деталь: | Compression Spring:Return |
| Парткод: | B091 2844 |
| Деталь: | Bushing - DC Motor Shaft |
| Парткод: | A267 2845 |
| Деталь: | Bracket:DC Motor:2 |
| Парткод: | B090 2838 |
| Деталь: | Shaft - DC Motor |
| Парткод: | A267 2840 |
| Деталь: | Bracket:DC Motor:1 |
| Парткод: | B090 2837 |
| Деталь: | Clip:Shaft |
| Парткод: | B031 2836 |
| Деталь: | Tension Spring:Pressure:Sub |
| Парткод: | B207 2773 |
| Деталь: | Harness Cover - Paper Feed |
| Парткод: | B024 2839 |
| Деталь: | Torsion Spring:Joint:Return |
| Парткод: | B091 2767 |
| Деталь: | Lever:Rise:Paper Volume Sensor |
| Парткод: | B090 2777 |
| Деталь: | Vibrating Plate |
| Парткод: | A267 2770 |
| Деталь: | Bracket:Rise:1 |
| Парткод: | B090 2815 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw:3x30 |
| Парткод: | 0451 3030N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Philips Truss Screw - M4x8 |
| Парткод: | 0950 4008Z |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | CLAMP |
| Парткод: | 11 050 460 |
| Деталь: | Clamp - ES-0510 |
| Парткод: | 11 050 329 |
| Деталь: | Bracket - BICU |
| Парткод: | D010 5810 |
| Деталь: | Harness:Scanner |
| Парткод: | D010 5222 |
| Деталь: | Hps Harness |
| Парткод: | D010 5220 |
| Деталь: | BICU Board |
| Парткод: | D010 5101 |
| Деталь: | M/H Assy:Paper Size Detect |
| Парткод: | D010 5231 |
| Деталь: | Density Sensor Harness |
| Парткод: | D010 5206 |
| Деталь: | Harness:LDD |
| Парткод: | D010 5250 |
| Деталь: | Scanner Motor Harness |
| Парткод: | D010 5200 |
| Деталь: | Harness - 1-bin Tray |
| Парткод: | D010 5255 |
| Деталь: | Harness:Document Feeder |
| Парткод: | D010 5240 |
| Деталь: | Harness - Power Supply Unit |
| Парткод: | D010 5230 |
| Деталь: | Duplex Harness |
| Парткод: | D010 5243 |
| Деталь: | Bracket - Power Supply Cord |
| Парткод: | D010 5825 |
| Деталь: | AC Harness - Fusing |
| Парткод: | D010 5218 |
| Деталь: | AC Harness - Fusing EU |
| Парткод: | D010 5217 |
| Деталь: | Power Supply Unit - 115V |
| Парткод: | AZ23 0213 |
| Деталь: | Power Supply Unit - 230V |
| Парткод: | AZ23 0214 |
| Деталь: | Harness - Main Switch |
| Парткод: | D010 5226 |
| Деталь: | AC Harness - Dehumidifier |
| Парткод: | D010 5228 |
| Деталь: | Harness:Power Supply Unit |
| Парткод: | D010 5230 |
| Деталь: | Harness:Joint Unit |
| Парткод: | D010 5207 |
| Деталь: | Power Supply Cord - NA |
| Парткод: | D010 5742 |
| Деталь: | Power Supply Cord - EU |
| Парткод: | D010 5743 |
| Деталь: | Choke Coil:B2435018 |
| Парткод: | B243 5018 |
| Деталь: | Joint Unit Harness |
| Парткод: | D010 5207 |
| Деталь: | Registration Sensor Harness |
| Парткод: | D010 5201 |
| Деталь: | Manual Feed Harness |
| Парткод: | D010 5212 |
| Деталь: | Development Sensor Harness |
| Парткод: | D010 5248 |
| Деталь: | Main Motor Harness |
| Парткод: | D010 5203 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Screw:M4X6 |
| Парткод: | 0950 4006Z |
| Деталь: | Edge Saddle - Les-1010 |
| Парткод: | 11 050 518 |
| Деталь: | Fuse - 6.3A 125V |
| Парткод: | 11 070 392 |
| Деталь: | Fuse:Ceramic Case:15A 125V |
| Парткод: | 11 070 629 |
| Деталь: | Ram:IDT7005L55pF |
| Парткод: | 14 075 229 |
| Деталь: | Connector:1-172157-2 |
| Парткод: | 11 028 510 |
| Деталь: | PCU Toner Supply Shutter |
| Парткод: | B121 2311 |
| Деталь: | SHUTTER SPRING |
| Парткод: | B039 2312 |
| Деталь: | Drum Shutter |
| Парткод: | B039 2343 |
| Деталь: | Pin - Front Pressure Arm |
| Парткод: | B039 2293 |
| Деталь: | Recycled Toner Coil |
| Парткод: | B039 2272 |
| Деталь: | Front PCU Cover |
| Парткод: | B039 2321 |
| Деталь: | Recycled Toner Plate |
| Парткод: | B039 2274 |
| Деталь: | TONER SUPPLY SEAL |
| Парткод: | B121 2313 |
| Деталь: | Rear Bushing - Toner Coil |
| Парткод: | B039 2276 |
| Деталь: | Drum Holder |
| Парткод: | B039 2350 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3444 |
| Деталь: | Gear - 13Z |
| Парткод: | AB01 1403 |
| Деталь: | Gear - 14Z |
| Парткод: | AB01 1402 |
| Деталь: | Pickoff Pawl |
| Парткод: | B039 2335 |
| Деталь: | Cleaning Blade Assy |
| Парткод: | AD04 2059 |
| Деталь: | Cam - Cleaning Blade |
| Парткод: | B039 2288 |
| Деталь: | OPC Drum |
| Парткод: | B039 9510 |
| Деталь: | Rear Pressure Arm - Charge Roller |
| Парткод: | B039 2295 |
| Деталь: | Charge Roller Spring |
| Парткод: | B039 2287 |
| Деталь: | Front Pressure Arm - Charge Roller |
| Парткод: | B039 2292 |
| Деталь: | Roller:Charge:A3 |
| Парткод: | AD02 7018 |
| Деталь: | Charge Cleaner Brush Roller |
| Парткод: | AD04 2058 |
| Деталь: | OPC Drum Shutter Plate |
| Парткод: | B259 2325 |
| Деталь: | Spacer - M3 |
| Парткод: | B039 2329 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Bushing 6x10 |
| Парткод: | 7 360 610 |
| Деталь: | Binding Self-Tapping Screw:M3x12 |
| Парткод: | 0452 3012N |
| Деталь: | PCU - Assy |
| Парткод: | B259 2210 |
| Деталь: | GRIP COVER |
| Парткод: | D010 1089 |
| Деталь: | GRIP |
| Парткод: | B276 1072 |
| Деталь: | Gear - 23Z |
| Парткод: | D010 1192 |
| Деталь: | Drive Shaft- Manual Feed |
| Парткод: | D010 1198 |
| Деталь: | Gear - 23Z |
| Парткод: | D010 1194 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Upper Guide Plate - Entarnce |
| Парткод: | D010 2733 |
| Деталь: | BUSHING - VERTICAL TRANSPORT |
| Парткод: | AA08 0249 |
| Деталь: | Compression Spring - 10n |
| Парткод: | B091 2739 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Decal - Vertical Transport Cover |
| Парткод: | B024 2737 |
| Деталь: | Cover - Vertical Transport |
| Парткод: | D010 2728 |
| Деталь: | Lower Guide Plate - Entrance |
| Парткод: | D010 2746 |
| Деталь: | Shaft:Door:Right Rear:Assy |
| Парткод: | D010 1058 |
| Деталь: | Door Shaft - Right Front |
| Парткод: | B259 1053 |
| Деталь: | Stopper:Right |
| Парткод: | D010 2632 |
| Деталь: | Tray Heater Assy(120V) |
| Парткод: | D010 7008 |
| Деталь: | Tray Heater Assy(230V) |
| Парткод: | D010 7018 |
| Деталь: | Roller:Pull Out:Option Tray |
| Парткод: | B090 2742 |
| Деталь: | Rubber Foot:H5 |
| Парткод: | AH01 0009 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | BUSHING - 6MM |
| Парткод: | 8 053 480 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Screw:Spring Washer:M3x6 |
| Парткод: | 0950 3006N |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | Original Sensor:H2-66 |
| Парткод: | AW01 0126 |
| Деталь: | Scanner Harness |
| Парткод: | D010 5222 |
| Деталь: | Pulley - 37Z |
| Парткод: | B039 1703 |
| Деталь: | Bracket - Idler |
| Парткод: | B039 1701 |
| Деталь: | Spring - Timing Pulley |
| Парткод: | B039 1704 |
| Деталь: | Lens Stay Bracket |
| Парткод: | B121 1667 |
| Деталь: | Timing Belt - 1058.25XL |
| Парткод: | B039 1697 |
| Деталь: | Timing Belt L147 |
| Парткод: | B121 1696 |
| Деталь: | Flange - Pulley |
| Парткод: | B039 1695 |
| Деталь: | Pulley - 37/41Z |
| Парткод: | B039 1694 |
| Деталь: | Scanner Drive Shaft |
| Парткод: | B259 1691 |
| Деталь: | Pulley - 37Z |
| Парткод: | B039 1692 |
| Деталь: | Bracket - Stabilizer Harness |
| Парткод: | B039 1668 |
| Деталь: | Bracket - Timing Belt |
| Парткод: | B121 1664 |
| Деталь: | Scanner Drive Motor - DC3.6V 2.88W |
| Парткод: | B039 1670 |
| Деталь: | Pulley shaft |
| Парткод: | B259 1702 |
| Деталь: | Tension Spring - Stepper Motor |
| Парткод: | B039 1683 |
| Деталь: | Gear - 53Z/60Z |
| Парткод: | B121 1680 |
| Деталь: | Front Scanner Frame |
| Парткод: | B039 1662 |
| Деталь: | Rear Scanner Frame |
| Парткод: | B039 1663 |
| Деталь: | Guide:FFC |
| Парткод: | D010 5822 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Bearing 8x22x7 |
| Парткод: | 8 053 530 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0453 3006N |
| Деталь: | Paper Tray:No.2:Assy |
| Парткод: | D010 2532 |
| Деталь: | Font Slider - Upper |
| Парткод: | D010 2867 |
| Деталь: | Front Slider - Base |
| Парткод: | D010 2873 |
| Деталь: | Front Side Fence |
| Парткод: | D010 2884 |
| Деталь: | END FENCE |
| Парткод: | D010 2853 |
| Деталь: | End Fence Seal |
| Парткод: | D010 2900 |
| Деталь: | Rear Side Fence |
| Парткод: | D010 2885 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | D010 2861 |
| Деталь: | Spacer:Link |
| Парткод: | D010 2550 |
| Деталь: | Spring Plate - Grounding |
| Парткод: | A267 2878 |
| Деталь: | Sponge - Paper Feed Tray |
| Парткод: | A267 2899 |
| Деталь: | Roller:Paper Tray |
| Парткод: | B090 2987 |
| Деталь: | Gear - 16Z |
| Парткод: | B090 2869 |
| Деталь: | Shaft - Tray Bottom Plate |
| Парткод: | D010 2854 |
| Деталь: | Lift Bracket |
| Парткод: | D010 2856 |
| Деталь: | Friction pad |
| Парткод: | B390 2831 |
| Деталь: | Pressure Spring - Friction Pad |
| Парткод: | A267 2834 |
| Деталь: | Sheet:Holder:Paper Tray |
| Парткод: | B091 2898 |
| Деталь: | Link - Paper Size Sensor |
| Парткод: | D010 2870 |
| Деталь: | BASE PAD |
| Парткод: | A267 2917 |
| Деталь: | Lever - Release Outer |
| Парткод: | B223 2864 |
| Деталь: | Release Shaft - Paper Tray |
| Парткод: | D010 2951 |
| Деталь: | Grip Holder - Paper Tray |
| Парткод: | D010 2955 |
| Деталь: | Release Lever - Paper Tray |
| Парткод: | D010 2953 |
| Деталь: | SPRING |
| Парткод: | AA06 0900 |
| Деталь: | Decal - Paper Set Direction |
| Парткод: | D010 2892 |
| Деталь: | Spring Plate - Slider |
| Парткод: | D010 2875 |
| Деталь: | PAPER TRAY COVER |
| Парткод: | D010 2958 |
| Деталь: | External Circlip - Mm8 |
| Парткод: | A222 2724 |
| Деталь: | Paper Tray Grip |
| Парткод: | D010 2954 |
| Деталь: | PAPER TRAY |
| Парткод: | D010 2850 |
| Деталь: | Lever:Stopper:Front |
| Парткод: | B090 2858 |
| Деталь: | Stopper:Positioning |
| Парткод: | B090 2859 |
| Деталь: | Lever:Stopper:Positioning |
| Парткод: | B090 2860 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | G697 2677 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Rear Slider - Base |
| Парткод: | D010 2874 |
| Деталь: | Side Fence Seal |
| Парткод: | D010 2897 |
| Деталь: | Rears Lider - Upper |
| Парткод: | D010 2866 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0450 4008N |
| Деталь: | Screw-m4x6 |
| Парткод: | 0354 0060N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Imaging Unit |
| Парткод: | D010 1876 |
| Деталь: | Cover:Shield Glass |
| Парткод: | B276 1251 |
| Деталь: | Adjusting Plate |
| Парткод: | B039 1905 |
| Деталь: | Discharge Lamp |
| Парткод: | D010 1080 |
| Деталь: | Discharge Lamp Harness |
| Парткод: | D010 5204 |
| Деталь: | Sheet - Duct |
| Парткод: | B039 1088 |
| Деталь: | Shield Glass |
| Парткод: | B039 1961 |
| Деталь: | Decal - LD |
| Парткод: | G029 1980 |
| Деталь: | Sync Detector Mirror |
| Парткод: | AC03 0139 |
| Деталь: | Cylindrical Lens |
| Парткод: | AC02 4009 |
| Деталь: | Cylindrical Lens Holder |
| Парткод: | B039 1942 |
| Деталь: | Holder - Sync Detector Mirror |
| Парткод: | B039 1954 |
| Деталь: | Optical Housing Cover |
| Парткод: | B039 1971 |
| Деталь: | Polygon Motor Harness |
| Парткод: | D010 5239 |
| Деталь: | LDD Harness |
| Парткод: | D010 5250 |
| Деталь: | Laser Diode Unit |
| Парткод: | D010 1916 |
| Деталь: | Polygon Mirror Motor - DC 12w |
| Парткод: | D010 1931 |
| Деталь: | Lens:L2 |
| Парткод: | GC02 5010 |
| Деталь: | 2nd Mirror Holder |
| Парткод: | B039 1953 |
| Деталь: | Sync Detector Lenz |
| Парткод: | AC02 0095 |
| Деталь: | Rubber Bushing |
| Парткод: | B121 1975 |
| Деталь: | Tapping Bind Screw - M3x10 |
| Парткод: | 0452 3010N |
| Деталь: | Tapping Screw -3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Tapping Screw:M3x20 |
| Парткод: | 0450 3020N |
| Деталь: | Tapping Screw - M3x14 |
| Парткод: | 0452 3014N |
| Деталь: | Clamp:LWS-0511Z |
| Парткод: | 11 050 487 |
| Деталь: | Cover - Expand |
| Парткод: | B622 5880 |
| Деталь: | PCB Gdi-Basic |
| Парткод: | B865 5171 |
| Деталь: | PCB BRACKET |
| Парткод: | B243 5870 |
| Деталь: | Rail Holder |
| Парткод: | B622 5872 |
| Деталь: | Cover - Card |
| Парткод: | B243 5879 |
| Деталь: | Cover - PCB |
| Парткод: | B243 5874 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Brushless Motor - DC 25W |
| Парткод: | D010 1127 |
| Деталь: | DC Solenoid Assy |
| Парткод: | B259 1135 |
| Деталь: | Timing Belt - 226XL |
| Парткод: | B039 1162 |
| Деталь: | Magnetic clutch |
| Парткод: | D010 1186 |
| Деталь: | Gear - 63Z |
| Парткод: | B039 1170 |
| Деталь: | DC Motor 24V |
| Парткод: | B259 3310 |
| Деталь: | Bushing - 8x16x9 |
| Парткод: | B039 1144 |
| Деталь: | Development Terminal |
| Парткод: | B039 1135 |
| Деталь: | OPC Drum Ground Plate 2 Assy |
| Парткод: | B121 1128 |
| Деталь: | Large Spring |
| Парткод: | B121 1161 |
| Деталь: | Fusing Swivel Bracket |
| Парткод: | B259 1157 |
| Деталь: | Coupled Gear - 20/49Z (12) |
| Парткод: | B039 1156 |
| Деталь: | Drum Shaft (02) |
| Парткод: | B039 1148 |
| Деталь: | Coupled Gear - 34/63Z (01) |
| Парткод: | B039 1145 |
| Деталь: | Coupled Gear - 32/71Z (04) |
| Парткод: | B039 1146 |
| Деталь: | Gear/pulley - 61/34Z (11) |
| Парткод: | B039 1155 |
| Деталь: | Development Drive Shaft (03) |
| Парткод: | B259 1174 |
| Деталь: | Coupled Gear - 37/97Z (05) |
| Парткод: | B039 1154 |
| Деталь: | Gear - 78Z (06) |
| Парткод: | B039 1173 |
| Деталь: | Gear - 32Z (10) |
| Парткод: | B039 1168 |
| Деталь: | Gear - 22Z (09) |
| Парткод: | B039 1167 |
| Деталь: | Coupled Gear - 49/59/38Z (08) |
| Парткод: | B039 1165 |
| Деталь: | Gear - 37Z (07) |
| Парткод: | B039 1166 |
| Деталь: | Bushing - 8mm |
| Парткод: | 53 041 639 |
| Деталь: | Main Drive Housing |
| Парткод: | B121 1140 |
| Деталь: | Snap Ring - M6 |
| Парткод: | AA10 0015 |
| Деталь: | Harness Hook |
| Парткод: | B121 1145 |
| Деталь: | Small Spring |
| Парткод: | B121 1162 |
| Деталь: | Tapping Screw:M4x10 |
| Парткод: | 0450 4010N |
| Деталь: | TAPPING SCREW |
| Парткод: | 0454 3008Q |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | TONER SUPPLY UNIT |
| Парткод: | B259 3031 |
| Деталь: | Cam - Handle |
| Парткод: | B039 3360 |
| Деталь: | Bottle Chuck |
| Парткод: | A184 3420 |
| Деталь: | Chuck Shaft |
| Парткод: | A184 3421 |
| Деталь: | Shaft:Slide |
| Парткод: | B259 3422 |
| Деталь: | Shaft - Paper Feed Frame |
| Парткод: | B039 1141 |
| Деталь: | Chuck Spring - Tonner Bottle |
| Парткод: | A267 3556 |
| Деталь: | SLIDER ASSY |
| Парткод: | G020 3334 |
| Деталь: | High Voltage Cable |
| Парткод: | D010 5232 |
| Деталь: | Terminal - Transfer |
| Парткод: | B039 3870 |
| Деталь: | GROUNDING PLATE |
| Парткод: | B039 2578 |
| Деталь: | Cover:Toner Bottle:Assy |
| Парткод: | B039 3381 |
| Деталь: | GROUND WIRE |
| Парткод: | D010 5219 |
| Деталь: | Quenching Lamp Terminal |
| Парткод: | B039 2382 |
| Деталь: | Guide Plate - Tonner Supply Unit |
| Парткод: | B039 3392 |
| Деталь: | Total Counter:7FIG:24V |
| Парткод: | AX31 0046 |
| Деталь: | Ground Plate - Toner Supply Unit |
| Парткод: | B039 3395 |
| Деталь: | Terminal - Separation |
| Парткод: | D010 3871 |
| Деталь: | Duct Seal - Sub |
| Парткод: | D010 1108 |
| Деталь: | Sub Duct |
| Парткод: | D010 1113 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Heater Wire Cover |
| Парткод: | B121 1084 |
| Деталь: | Switch:LF-105-11 |
| Парткод: | B268 1085 |
| Деталь: | Exit Roller 2 |
| Парткод: | B259 4471 |
| Деталь: | Ring:Exit Roller |
| Парткод: | B039 4473 |
| Деталь: | Bushing - 8x10x5 |
| Парткод: | AA08 2063 |
| Деталь: | Door Switch Bracket |
| Парткод: | B039 1082 |
| Деталь: | Door Switch Harness - Front |
| Парткод: | D010 5205 |
| Деталь: | Door Switch Lever - 7 |
| Парткод: | B039 1096 |
| Деталь: | Door Switch Lever - 8 |
| Парткод: | B039 1123 |
| Деталь: | Door Switch Lever - 6 |
| Парткод: | B039 1095 |
| Деталь: | Door Switch Lever - 5 |
| Парткод: | B039 1094 |
| Деталь: | Door Switch Spring |
| Парткод: | B039 1098 |
| Деталь: | Door Switch Lever - 4 |
| Парткод: | B039 1093 |
| Деталь: | Door Switch Lever - 3 |
| Парткод: | B039 1092 |
| Деталь: | Door Switch Lever - 2 |
| Парткод: | B039 1099 |
| Деталь: | Door Switch Lever - 1 |
| Парткод: | B039 1090 |
| Деталь: | Ground Wire - Fusing Unit |
| Парткод: | D010 5270 |
| Деталь: | Ground Plate - Fusing Unit |
| Парткод: | B039 4116 |
| Деталь: | Exit Photointerruptor Bracket |
| Парткод: | B121 4503 |
| Деталь: | Exit Middle Guide Plate |
| Парткод: | B121 4451 |
| Деталь: | Relay Harness - Paper Feed Sensor |
| Парткод: | D010 5238 |
| Деталь: | Photointerruptor - Duplex |
| Парткод: | G361 5570 |
| Деталь: | EXIT ROLLER |
| Парткод: | B043 4979 |
| Деталь: | Gate Pawl |
| Парткод: | B261 4983 |
| Деталь: | Gate Pawl Spring |
| Парткод: | AA06 6641 |
| Деталь: | Pulley - 23Z |
| Парткод: | B039 1163 |
| Деталь: | Fusing Drive Release Bracket |
| Парткод: | B121 1132 |
| Деталь: | Exit Roller Ring Mm14 |
| Парткод: | B121 4473 |
| Деталь: | Outer Exit Cover Roller |
| Парткод: | G052 4873 |
| Деталь: | Short Front Outer Holder |
| Парткод: | B121 4465 |
| Деталь: | Long Rear Middle Holder |
| Парткод: | B121 4469 |
| Деталь: | Short Rear Outer Holder |
| Парткод: | B121 4477 |
| Деталь: | Long Front Middle Holder |
| Парткод: | B121 4467 |
| Деталь: | Exit Lower Guide Plate |
| Парткод: | B121 4461 |
| Деталь: | Turn Roller - Exit Sub-unit |
| Парткод: | G029 4176 |
| Деталь: | Exit Roller Holder - Inner |
| Парткод: | B039 4459 |
| Деталь: | EXIT ROLLER |
| Парткод: | G800 4854 |
| Деталь: | Middle:Reverse Holder |
| Парткод: | B123 4508 |
| Деталь: | Large Exit Discharge Brush |
| Парткод: | B122 4492 |
| Деталь: | Small Exit Discharge Brush |
| Парткод: | B122 4493 |
| Деталь: | Harness Guide |
| Парткод: | B121 1126 |
| Деталь: | Lower Exit Guide Plate |
| Парткод: | B122 4460 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0450 4008N |
| Деталь: | 1st Paper Tray Unit |
| Парткод: | D010 2531 |
| Деталь: | Font Slider - Upper |
| Парткод: | D010 2867 |
| Деталь: | Front Slider - Base |
| Парткод: | D010 2873 |
| Деталь: | Front Side Fence |
| Парткод: | D010 2884 |
| Деталь: | END FENCE |
| Парткод: | D010 2853 |
| Деталь: | End Fence Seal |
| Парткод: | D010 2900 |
| Деталь: | Rear Side Fence |
| Парткод: | D010 2885 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | D010 2861 |
| Деталь: | Spacer:Link |
| Парткод: | D010 2550 |
| Деталь: | Spring Plate - Grounding |
| Парткод: | A267 2878 |
| Деталь: | Sponge - Paper Feed Tray |
| Парткод: | A267 2899 |
| Деталь: | Roller:Paper Tray |
| Парткод: | B090 2987 |
| Деталь: | Gear - 16Z |
| Парткод: | B090 2869 |
| Деталь: | Shaft - Tray Bottom Plate |
| Парткод: | D010 2854 |
| Деталь: | Lift Bracket |
| Парткод: | D010 2856 |
| Деталь: | Friction pad |
| Парткод: | B390 2831 |
| Деталь: | Pressure Spring - Friction Pad |
| Парткод: | A267 2834 |
| Деталь: | Sheet:Holder:Paper Tray |
| Парткод: | B091 2898 |
| Деталь: | Link - Paper Size Sensor |
| Парткод: | D010 2870 |
| Деталь: | BASE PAD |
| Парткод: | A267 2917 |
| Деталь: | Lever - Release Outer |
| Парткод: | B223 2864 |
| Деталь: | Release Shaft - Paper Tray |
| Парткод: | D010 2951 |
| Деталь: | Grip Holder - Paper Tray |
| Парткод: | D010 2955 |
| Деталь: | Release Lever - Paper Tray |
| Парткод: | D010 2953 |
| Деталь: | SPRING |
| Парткод: | AA06 0900 |
| Деталь: | Decal - Paper Set Direction |
| Парткод: | D010 2892 |
| Деталь: | Spring Plate - Slider |
| Парткод: | D010 2875 |
| Деталь: | PAPER TRAY COVER |
| Парткод: | D010 2958 |
| Деталь: | External Circlip - Mm8 |
| Парткод: | A222 2724 |
| Деталь: | Paper Tray Grip |
| Парткод: | D010 2954 |
| Деталь: | PAPER TRAY |
| Парткод: | D010 2850 |
| Деталь: | Lever:Stopper:Front |
| Парткод: | B090 2858 |
| Деталь: | Stopper:Positioning |
| Парткод: | B090 2859 |
| Деталь: | Lever:Stopper:Positioning |
| Парткод: | B090 2860 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | G697 2677 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Rear Slider - Base |
| Парткод: | D010 2874 |
| Деталь: | Side Fence Seal |
| Парткод: | D010 2897 |
| Деталь: | Rears Lider - Upper |
| Парткод: | D010 2866 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0450 4008N |
| Деталь: | Screw-m4x6 |
| Парткод: | 0354 0060N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Bracket - Registration Roller |
| Парткод: | B039 2575 |
| Деталь: | Registration Roller Spring |
| Парткод: | AA06 2254 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Gear - 16Z |
| Парткод: | AB01 2312 |
| Деталь: | Fornt Bushing-registration Roller |
| Парткод: | AA08 0342 |
| Деталь: | Bushing - 8x12x18 |
| Парткод: | AA08 0267 |
| Деталь: | Gear - 18Z |
| Парткод: | AB01 2311 |
| Деталь: | Snap Ring - M6 |
| Парткод: | AA10 0015 |
| Деталь: | TRANSFER UNIT |
| Парткод: | D010 3804 |
| Деталь: | Registration Sensor Spring |
| Парткод: | AA06 6342 |
| Деталь: | Registration Feeler |
| Парткод: | B039 2570 |
| Деталь: | Guide - Right Registration Roller |
| Парткод: | B039 2567 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Interface Harness - Registration |
| Парткод: | D010 5202 |
| Деталь: | Registration Cleaning Mylar |
| Парткод: | B039 2560 |
| Деталь: | Guide Plate - Driven Roller |
| Парткод: | D010 2572 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | B039 2558 |
| Деталь: | Registration Roller Driven - Dia16 |
| Парткод: | B259 2571 |
| Деталь: | Registration Roller Drive |
| Парткод: | B259 2562 |
| Деталь: | Development Sensor Bracket |
| Парткод: | B039 1130 |
| Деталь: | Harness - Development Sensor |
| Парткод: | B121 5248 |
| Деталь: | Rear Bushing-registration Roller |
| Парткод: | AA08 0343 |
| Деталь: | Bushing - 8x12x22 |
| Парткод: | AA08 2110 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3607 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | B039 3820 |
| Деталь: | DENSITY SENSOR |
| Парткод: | B259 3890 |
| Деталь: | ID Sensor Cover |
| Парткод: | B039 3891 |
| Деталь: | Screw:PCU |
| Парткод: | B259 1131 |
| Деталь: | Harness - Density Sensor |
| Парткод: | B121 5206 |
| Деталь: | Roller - Transfer Unit |
| Парткод: | B039 3867 |
| Деталь: | Quenching Terminal Plate |
| Парткод: | B039 3863 |
| Деталь: | Registration Guide Spacer |
| Парткод: | B043 2554 |
| Деталь: | HARNESS COVER |
| Парткод: | B121 3860 |
| Деталь: | Quenching Terminal Plate-front |
| Парткод: | B039 3864 |
| Деталь: | Transfer Terminal Plate |
| Парткод: | B039 3865 |
| Деталь: | Front Discharge Brush |
| Парткод: | B120 3862 |
| Деталь: | Pressure Cover |
| Парткод: | B039 3866 |
| Деталь: | Guide Plate:Transfer:Upper |
| Парткод: | B039 3859 |
| Деталь: | Holder:Separation |
| Парткод: | D010 3860 |
| Деталь: | Electrode Plate:Separation |
| Парткод: | B039 3861 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11 050 522 |
| Деталь: | Bracket:Paper End Sensor |
| Парткод: | B090 2805 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | A267 2803 |
| Деталь: | Stopper Paper Feed Roller |
| Парткод: | B093 2935 |
| Деталь: | Relay Harness - Paper End Sensor |
| Парткод: | D010 5216 |
| Деталь: | Guide Plate - Paper Feed Roller 2 |
| Парткод: | D010 2808 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | A267 2754 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A267 2751 |
| Деталь: | Guide Roller |
| Парткод: | D010 2565 |
| Деталь: | Bracket:Guide Plate:No.2 |
| Парткод: | D010 2587 |
| Деталь: | Guide Plate:Pressure Release :Friction Pad:Upper |
| Парткод: | D010 2828 |
| Деталь: | Drive Roller - Vertical Transport |
| Парткод: | D010 2682 |
| Деталь: | Bracket - Photointerruptor |
| Парткод: | D010 2660 |
| Деталь: | Photointerruptor:Vertical Transport |
| Парткод: | AW02 0173 |
| Деталь: | Snap Ring |
| Парткод: | B090 2686 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0252 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Clamp:LES-1010 |
| Парткод: | 11 050 522 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Retaining Ring - 3m |
| Парткод: | 8 050 092 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | BUSHING - 6MM |
| Парткод: | 8 053 480 |
| Деталь: | Harness Clamp:RLMC-05TV0 |
| Парткод: | 11 050 501 |
| Деталь: | Reverse Roller |
| Парткод: | B261 4989 |
| Деталь: | Gear - 18Z |
| Парткод: | B043 4975 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | B121 4490 |
| Деталь: | Guide Plate:Reverse:Left Upper |
| Парткод: | B269 4981 |
| Деталь: | Front Reverse Sub-unit Holder |
| Парткод: | B122 1075 |
| Деталь: | Reverse Roller Ground Plate |
| Парткод: | B123 4506 |
| Деталь: | Ground Wire - Duplex |
| Парткод: | D010 5245 |
| Деталь: | Reverse Paper Feed Sensor Bracket |
| Парткод: | B123 4973 |
| Деталь: | PHOTO REFIECTION SENSOR:EXIT |
| Парткод: | GW01 0007 |
| Деталь: | Sensor Relay Harness - Duplex |
| Парткод: | D010 5253 |
| Деталь: | Middle Reverse Guide Plate |
| Парткод: | B123 4502 |
| Деталь: | EXIT ROLLER |
| Парткод: | B043 4979 |
| Деталь: | Middle:Reverse Holder |
| Парткод: | B123 4508 |
| Деталь: | EXIT ROLLER |
| Парткод: | G800 4854 |
| Деталь: | DC Solenoid |
| Парткод: | D010 4984 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Bushing - M5 |
| Парткод: | 8 053 383 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Rocker Switch:Sddje33900 |
| Парткод: | 12 042 608 |
| Деталь: | Support Spacer - M3x29 |
| Парткод: | 11 050 499 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Cover:Printer:Basic |
| Парткод: | B243 1461 |
| Деталь: | Sheet:Power Source:NA |
| Парткод: | B229 1521 |
| Деталь: | Sheet:Power Source:EU |
| Парткод: | D010 1522 |
| Деталь: | PCB Operation Panel |
| Парткод: | B243 1487 |
| Деталь: | Operation Panel Unit NA |
| Парткод: | B277 1411 |
| Деталь: | Operation Panel - EU |
| Парткод: | D010 1412 |
| Деталь: | Cover:Operation Sub-unit:Lower |
| Парткод: | B276 1452 |
| Деталь: | Cover - Operation Panel |
| Парткод: | B243 1425 |
| Деталь: | GROUND PLATE |
| Парткод: | B039 1469 |
| Деталь: | Keytop - Start |
| Парткод: | B229 1453 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B229 1454 |
| Деталь: | Keytop - 10key NA |
| Парткод: | B229 1526 |
| Деталь: | Keytop - 10key (EU) |
| Парткод: | B229 1475 |
| Деталь: | Keytop-initial |
| Парткод: | B229 1525 |
| Деталь: | Keytop - Clear Modes |
| Парткод: | B229 1537 |
| Деталь: | Keytop - Power Source |
| Парткод: | B243 1458 |
| Деталь: | Keytop - Cursor |
| Парткод: | B243 1459 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | B259 1499 |
| Деталь: | Cover - CPS NA |
| Парткод: | B243 1466 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | Bracket:Paper End Sensor |
| Парткод: | B090 2805 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | A267 2803 |
| Деталь: | SHAFT HOLDER |
| Парткод: | D010 2807 |
| Деталь: | Guide Plate - Paper Feed Roller 1 |
| Парткод: | D010 2800 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | D010 2754 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A267 2751 |
| Деталь: | Relay Harness - Paper End Sensor |
| Парткод: | D010 5216 |
| Деталь: | Front Heater Bracket |
| Парткод: | B121 4201 |
| Деталь: | Guide Plate:Pressure Release :Friction Pad:Upper |
| Парткод: | D010 2828 |
| Деталь: | Drive Roller - Vertical Transport |
| Парткод: | B090 2668 |
| Деталь: | Bracket - Photointerruptor |
| Парткод: | D010 2663 |
| Деталь: | Photointerruptor:Vertical Transport |
| Парткод: | AW02 0173 |
| Деталь: | Snap Ring |
| Парткод: | B090 2686 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0252 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11 050 522 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
Коды ошибок
01
101
120
121
141
143
144
145
193
198
202
203
204
220
230
302
390
391
392
402
411
490
500
501
502
503
504
506
541
542
543
544
545
546
547
551
552
553
555
556
557
559
590
591
620
621
632
634
635
692
694
740
742
750
760
761
762
792
793
794
795
796
797
901
903
928
929
954
955
964
981
982
984
Описание
| Error code: | 01 |
| Display: | ERROR CONDITION INVALID HEAD |
| Description: | The ERROR light flashes. |
| Causes: | The printhead was replaced with one that is not a genuine Zebra™ printhead. |
| Remedy: | Install a genuine Zebra printhead. |
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 141 |
| Display: | SVC 141 ERROR |
| Description: | Motor |
| Causes: | • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor excessive PWM - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board” |
| Error code: | 143 |
| Display: | Service Call 143:Error |
| Description: | Motor |
| Causes: | • SBU defective • IPU defective • BCU defective • Harness between the SBU and IPU defective • Harness between the BCU-IPU defective • Standard white plate not installed correctly, or is dirty • Scanner mirrors and/or lenses are dirty or installed incorrectly |
| Remedy: | DC pick motor, no encoder feedback - staging motor - replace the “Staging motor” on page 4-79. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 145 |
| Display: | SYSTEM HALT (*) 145 : MAIN CN6,9 CHK |
| Description: | Motor |
| Causes: | • Exposure lamp defective • Dirty white plate • Incorrect position or width of white plate scanning (SP4015) • BICU board defective • SBU board defective |
| Remedy: | DC motor excessive PWM autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 193 |
| Description: | Image transfer error The IPU board does not finish within 1 minute after the image data has been transferred to the controller board. |
| Causes: | • IPU board defective • Controller board defective • Video controller defective |
| Error code: | 198 |
| Description: | Memory address error The IPU board does not receive the memory address from the controller board. |
| Causes: | • Mismatched firmware between the SBCU board and controller board • Controller defective • SBCU defective • IPU board defective Note: Before you replace a board, update the firmware. This can repair the error. |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 204 |
| Display: | Power OFF/ON 204:Error |
| Description: | Polygon motor error 3: XSCRDY signal error |
| Causes: | The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing. |
| Remedy: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board). |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 390 |
| Display: | Check MP tray 390: Paper jam |
| Description: | Paper jam during paper feed from MT. |
| Causes: | Check for miss-fed paper around MT cassette. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace MT. |
| Error code: | 391 |
| Description: | TD sensor error: Auto adjust error During automatic adjustment of the TD sensor, output voltage was less than 1.8V, or more than 4.8V during TD sensor initial setting |
| Causes: | • TD sensor connector or harness loose, broken, defective • TD sensor defective • IOB defective • Toner supply defective (confirm that the toner seal strip has been removed from toner cartridge) |
| Remedy: | 1. Check the harness or harness connection. 2. Clean the surface of the quenching lamp glass. |
| Error code: | 392 |
| Description: | Development Bias Error The development bias feedback voltage was less than 0.3 V for longer than 200 ms while the PWM duty value was more than 5% (indicating a development bias leak). |
| Causes: | • Bias terminal damaged • High voltage cable damaged, defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 411 |
| Display: | SVC 411 ERROR |
| Description: | IRQ timer 1 error |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | Replace the Controller board. |
| Error code: | 490 |
| Display: | Set 490: No paper in MP tray (* stands for A4 B4, etc.) |
| Description: | ITB (Image Transfer Belt) Unit Set Error |
| Causes: | The TM sensor does not detect the reflection from the ITB. |
| Remedy: | • No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S |
| Error code: | 500 |
| Description: | Transport/Fusing Motor Error |
| Causes: | The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the transport/fusing motor. Replace it if necessary. |
| Error code: | 501 |
| Display: | Service Call 501: Error |
| Description: | Tray 1 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503 |
| Display: | Service Call 503: Error |
| Description: | Tray 3 must be rebuilt |
| Causes: | (A model other than D581) Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. (D581) Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 504 |
| Description: | Tray 4 must be rebuilt |
| Causes: | The 2nd tray of D580, 1st tray of D580 when D579 and D580 are attached, the bottom D579 when two units of D579 are attached, or D631 when D581 and D631 are attached. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection D581 when D579 and D581 are attached.Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 506 |
| Display: | SYSTEM HALT (*) 506 : STATION SENS |
| Description: | Bypass must be rebuilt |
| Causes: | • Paper tray unit main motor connector or harness loose, broken, defective • Motor overload due to an obstruction • Motor defective |
| Remedy: | 1. Replace the tray 3 or 4 lift motor. 2. Replace the tray 3 or 4 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3 or 4. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 555 |
| Description: | Fusing Heater error: End The fusing heater keeps full power for 9 seconds or more. |
| Causes: | Defective thermistors. Broken heater cables. |
| Error code: | 556 |
| Description: | Unstable fusing temperature (rear) The fusing temperature varies 50° C or more within 1 second, and this occurs 2 consecutive times. |
| Causes: | • Thermistor defective or out of position • Power supply unit defective |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 590 |
| Description: | Toner collection motor error The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on. |
| Causes: | • Motor lock due to obstruction • Motor driver board defective • Motor connection loose, defective • Toner collection motor sensor disconnected, sensor defective • Rotational transmission shaft (o6 x 30) missing |
| Error code: | 591 |
| Description: | NC sensor broken: End The sensor detects -17°C or less for 6 seconds. |
| Causes: | Broken cables of thermopile. Broken cables of thermistor. Loose connection. |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 692 |
| Description: | GAVD block 12C bus error The I2C bus of the BICU is defective |
| Causes: | • Replace BICU |
| Error code: | 694 |
| Description: | Controller board communication abnormal Communication error between the scanner part of the controller board and BICU. |
| Causes: | • The connector is abnormal between the controller board and the BICU board. |
| Error code: | 740 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished after a certain time. For the 1000-sheet booklet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 742 |
| Description: | Finisher stapler movement motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished for a certain time. For the 1000-sheet booklet finisher • The stapler HP sensor is not activated within the specified time after the stapler motor turned on. (first detection: jam error, consecutive twice detection SC code). |
| Causes: | • Motor overload • Loose connection of the stapler home position sensor • Loose connection of the stapler movement motor • Defective stapler home position sensor • Defective stapler movement motor |
| Remedy: | 1. Check the connection of the stapler movement motor. 2. Check the connection of the stapler home position sensor. 3. Replace the stapler home position sensor. 4. Replace the stapler movement motor. |
| Error code: | 750 |
| Description: | 1000/3000-sheet (booklet) finisher: Tray lift motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. |
| Causes: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor |
| Remedy: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor. |
| Error code: | 760 |
| Description: | Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Punch HP sensor disconnected, defective • Punch motor disconnected or defective • Punch motor overload due to obstruction |
| Remedy: | 1. Check the connections and cables for the punch motor and HP sensor. 2. Check for blockages in the punch motor mechanism. 3. Replace the punch HP sensor and/or punch motor 4. Replace the finisher main board. |
| Error code: | 761 |
| Description: | Finisher folder plate motor error The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Remedy: | 1. Check the connections and cables for the folder plate motor and HP sensor. 2. Check for blockages in the folder plate motor mechanism. 3. Replace the folder plate HP sensor and/or folder plate motor 4. Replace the finisher main board. |
| Error code: | 762 |
| Description: | Front fold plate HP sensor error The state (on/off, off/on) of the front fold plate HP sensor in the fan fold unit did not change 1 sec. after the plate started to move. |
| Causes: | • Fold plate motor (F) harness connector loose, disconnected, broken • Front fold plate HP sensor harness connector loose, disconnected, broken • Fold plate motor (F) defective • Front fold plate HP sensor defective • Undetected paper is jamming the action of the motor or fold plate • Fan folder unit MCU defective |
| Error code: | 792 |
| Description: | Finisher error The machine does not recognize the finisher, but recognizes the bridge unit. |
| Causes: | The finisher`s connection is faulty. The finisher is not attached to a device equipped with the bridge unit. Defective finisher. |
| Remedy: | Reconnect the finisher or bridge unit, and then turn the main power switch off and then back on. |
| Error code: | 793 |
| Description: | Finisher gathering roller motor error |
| Causes: | • Motor overload • Loose connection of the gathering roller motor • Defective gathering roller motor |
| Remedy: | • Check the connections to the gathering roller motor. • Replace the gathering roller motor. |
| Error code: | 794 |
| Description: | Finisher exit guide plate motor error |
| Causes: | • Motor overload • Loose connection of the exit guide plate motor • Defective exit guide plate motor |
| Remedy: | 1. Check the connections to the exit guide plate motor. 2. Replace the exit guide plate motor. |
| Error code: | 795 |
| Description: | Finisher shift roller motor error |
| Causes: | • Motor overload • Loose connection of the shift roller motor • Defective shift roller motor |
| Remedy: | • Check the connections to the shift roller motor. • Replace the shift roller motor. |
| Error code: | 796 |
| Description: | Finisher tray lift motor error |
| Causes: | • Motor overload • Loose connection of the tray lift motor • Defective tray lift motor |
| Remedy: | • Check the connections to the tray lift motor. • Replace the tray lift motor. |
| Error code: | 797 |
| Description: | EEPROM data error |
| Causes: | Defective EEPROM on the main board |
| Remedy: | 1. Check the harness connection. 2. Replace the main board. |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 903 |
| Display: | Power OFF/ON 903:Error |
| Description: | Paperport link driver error |
| Causes: | These errors indicate an unrecoverable system software error. |
| Remedy: | Replace the system board. |
| Error code: | 928 |
| Display: | Power Off/on 928: Error |
| Description: | Failure in the Fuser Motor The Fuser Motor has stopped rotating. Applicable Status Code: Code 928: The Fuser Motor has failed. |
| Causes: | • Fuser Motor, PL2.1.9 • Motor Driver Board, PL2.1.10 • Engine Control Board, PL1.1.4 |
| Remedy: | 1 Test the Fuser Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Fuser Motor test. Does the motor operate? Complete. Replace the motor. If the error persists, go to Step 2. 2 Check for +24 V to the Fuser Motor. Is the +24 V across DCHEAT- 3 <=> ground? Go to Step 5. Go to Step 3. 3 Check Motor Driver Board POW24 connector for 24 V. 1. Disconnect POW24. Is the +24 V across POW24 pins 1 and 2? Replace the Motor Driver Board. Go to Step 4. 4 Check for 24 V at the LVPS 1. Disconnect CN2 on the LVPS. Is the +24 V across pins 1 and 2? Replace the POW24 Harness. Replace the LVPS. 5 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 929 |
| Display: | Power Off/on 929: Error |
| Description: | Failure in the Waste Toner Motor The Waste Toner Motor has stopped rotating. Applicable Status Code: Code 929: The Waste Toner Motor has failed. |
| Causes: | • Waste Toner Motor, PL7.1.3 • Motor Driver Board, PL2.1.10 • Engine Control Boar d, PL1.1.4 |
| Remedy: | 1 Test the Waste Toner Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Waste Toner Motor test. Does the motor operate? Complete. Replace the motor. If the error persists, go to Step 2. 2 Check for +24 V to the Waste Toner Motor. Is the +24 V across WTDC- 3 <=> ground? Go to Step 5. Go to Step 3. 3 Check Motor Driver Board POW24 connector for 24 V. 1. Disconnect POW24. Is the +24 V across POW24 pins 1 and 2? Replace the Motor Driver Board. Go to Step 4. 4 Check for 24 V at the LVPS 1. Disconnect CN2 on the LVPS. Is the +24 V across pins 1 and 2? Replace the POW24 Harness. Replace the LVPS. 5 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 954 |
| Description: | NVRAM CRC Failure |
| Causes: | • Firmware bug • IPU defective |
| Remedy: | Indicates the NVRAM experienced a CRC failure. Replace the interconnect board. |
| Error code: | 955 |
| Description: | Code CRC <loc> |
| Causes: | • Firmware bug • Hard disk unit defective • Controller defective • MCU defective • IPU defective |
| Remedy: | Replace the system board. Where <loc> = CRC Failure or ECC Failure on the system board. |
| Error code: | 964 |
| Description: | Emulation Error |
| Causes: | • Software defective |
| Remedy: | Indicates a failure within the Download Emulation which is programmed into the code overlay card. The specific error is as follows: 964 - Download Emulation CRC Failure. Checksum Failure. |
| Error code: | 981 |
| Display: | Service call 981: Error |
| Description: | <device> |
| Causes: | • Defective NVRAM • Loose connection between the BICU and the NVRAM • Incorrect installation of the NVRAM • Defective BICU |
| Remedy: | The engine protocol violation detected by the specified device. |
| Error code: | 982 |
| Display: | Service call 982: Error |
| Description: | <device> Comm |
| Causes: | • Localization setting not specified (The main power switch is turned on for the first time after the NVRAM is replaced.) • Incorrect localization setting • Defective NVRAM |
| Remedy: | Communications error detected by the specified device. |
| Error code: | 984 |
| Display: | Service call 984: Error. |
| Description: | <device> |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected |
| Remedy: | Invalid command parameter received by the specified device. Note: Service errors 980 thru 984 <device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
