Ricoh MP2851
Рейтинг
Модули
ELECTRICAL SECTION 2
Drive Section 1
DRIVE SECTION 2
PAPER REGISTRATION
ELECTRICAL SECTION 3
LASER UNIT
FUSING UNIT 1
PCU SECTION
2ND PAPER FEED SECTION
ELECTRICAL SECTION 1
VERTICAL TRANSPORT
EXTERIOR 1
1ST PAPER FEED SECTION
Paper exit
FRAME SECTION
TONER HOPPER UNIT
SCANNER SECTION 2
EXTERIOR 2
Scanner Section 1
FUSING UNIT 2
TRANSFER UNIT
DRIVE SECTION 3
PAPER TRAY
OPERATION PANEL
SCANNER SECTION 3
Детали Paper exit
| Деталь: | SIO Board (MS model) |
| Парткод: | D019 5110 |
| Деталь: | SIO Board - CS (CS model) |
| Парткод: | D020 5180 |
| Деталь: | Harness - SBU Power MS (MS model) |
| Парткод: | D019 5254 |
| Деталь: | Harness - SBU (CS model) |
| Парткод: | B238 5368 |
| Деталь: | Harness - BCU-SIO |
| Парткод: | D019 5248 |
| Деталь: | Bracket:Power Pack |
| Парткод: | B090 5833 |
| Деталь: | Spacer - KGLS-12RF |
| Парткод: | G020 5871 |
| Деталь: | Power Pack - BCTD |
| Парткод: | AZ32 0158 |
| Деталь: | Harness - Power Pack |
| Парткод: | D019 5217 |
| Деталь: | Upper Stand - IOB |
| Парткод: | D019 5839 |
| Деталь: | Harness - ADF |
| Парткод: | D019 5200 |
| Деталь: | Lower Stand - IOB |
| Парткод: | D019 5840 |
| Деталь: | Shadeing Plate - Controller |
| Парткод: | D019 5875 |
| Деталь: | Application Rack - Lower |
| Парткод: | D019 5860 |
| Деталь: | Application Rack - Upper |
| Парткод: | D019 5856 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Support Spacer - M3x29 |
| Парткод: | 1105 0499 |
| Деталь: | CLAMP |
| Парткод: | 1105 0516 |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0487 |
| Деталь: | WIRE SADDLE |
| Парткод: | 1105 0292 |
| Деталь: | Cover:Fusing:Drive |
| Парткод: | B090 1162 |
| Деталь: | Gear - 27Z |
| Парткод: | AB01 1204 |
| Деталь: | Gear - 35Z/28Z |
| Парткод: | AB01 7503 |
| Деталь: | Timing Belt - S3M - 225 |
| Парткод: | AA04 3515 |
| Деталь: | Bracket:Fusing:Swivel |
| Парткод: | B090 1170 |
| Деталь: | Gear - 30Z |
| Парткод: | AB01 1203 |
| Деталь: | Bracket:Fusing:Drive |
| Парткод: | B090 1159 |
| Деталь: | Lever:Dcsol:Assy |
| Парткод: | B209 1167 |
| Деталь: | Gear - 44Z |
| Парткод: | AB01 4050 |
| Деталь: | Timing Belt - S3M - 342 |
| Парткод: | AA04 3516 |
| Деталь: | Timing Pulley - 27T/48T |
| Парткод: | AB03 3092 |
| Деталь: | Timing Belt - S3M - 420 |
| Парткод: | AA04 3514 |
| Деталь: | Timing Pulley - 31/36T |
| Парткод: | B090 1111 |
| Деталь: | Spring:Tension |
| Парткод: | B091 2615 |
| Деталь: | Bracket:Tension |
| Парткод: | B090 1115 |
| Деталь: | Receptacle - Transfer/Separation |
| Парткод: | D019 3950 |
| Деталь: | Guide Plate:Fusing Unit:Rear:C |
| Парткод: | B090 1076 |
| Деталь: | Fusing AC Harness - 120V |
| Парткод: | D019 5271 |
| Деталь: | Fusing AC Harness - 230V |
| Парткод: | D019 5272 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3301 |
| Деталь: | PCB:PCU |
| Парткод: | B209 5156 |
| Деталь: | Charge Receptacle |
| Парткод: | D019 3461 |
| Деталь: | Fly Wheel - 118.5MM |
| Парткод: | D019 1184 |
| Деталь: | Brushless Motor-DC 30W |
| Парткод: | D019 1129 |
| Деталь: | Harness - High Voltage B:R-C |
| Парткод: | D019 5218 |
| Деталь: | Screw:PCU |
| Парткод: | B259 1131 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Screw:Polished Roud:M3x8 |
| Парткод: | 0951 3008N |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 0804 6123 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0805 0089 |
| Деталь: | Clamp:FC-30 |
| Парткод: | 1105 0687 |
| Деталь: | Harness Bracket |
| Парткод: | D019 5824 |
| Деталь: | Bracket:Connecting:Paper Feed |
| Парткод: | B209 1183 |
| Деталь: | Gear - Joint Paper Feed |
| Парткод: | AB01 7522 |
| Деталь: | Gear Pulley - Registration |
| Парткод: | AB01 7625 |
| Деталь: | Timing Belt - S3M - 342 |
| Парткод: | AA04 3516 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | TIMING PULLEY - 18T |
| Парткод: | AB03 0627 |
| Деталь: | Spring:Tension |
| Парткод: | B091 2615 |
| Деталь: | Bracket:Tension |
| Парткод: | B090 2602 |
| Деталь: | Gear - 31Z/54Z |
| Парткод: | AB01 1199 |
| Деталь: | Timing Belt - S3M - 315 |
| Парткод: | AA04 3517 |
| Деталь: | Timing Pulley - 20T |
| Парткод: | AB03 0626 |
| Деталь: | Magnetic Clutch:0.35N M:Z50 |
| Парткод: | D019 2816 |
| Деталь: | O/O (200903 PCIL) |
| Парткод: | D019 2616 |
| Деталь: | Magnetic Clutch:0.25N M:Z38 |
| Парткод: | AX20 0290 |
| Деталь: | O/O (200903 PCIL) |
| Парткод: | D019 2617 |
| Деталь: | Stopper:Feed:Cl |
| Парткод: | B090 2604 |
| Деталь: | Cover:Drive:Paper Feed:Right |
| Парткод: | D019 2596 |
| Деталь: | Grip - Rear Right |
| Парткод: | D019 5828 |
| Деталь: | Connector Bracket - Manual Feed |
| Парткод: | D019 5826 |
| Деталь: | Bracket - Grip |
| Парткод: | D019 5834 |
| Деталь: | Snap Ring |
| Парткод: | B091 2607 |
| Деталь: | Positioning Guide - Bypass Feed |
| Парткод: | A267 2601 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 0804 6123 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | CLAMP |
| Парткод: | 1105 0516 |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0488 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Cleaner-registration |
| Парткод: | D019 2755 |
| Деталь: | Discharge Lamp |
| Парткод: | B209 3452 |
| Деталь: | Registration Roller - Drive |
| Парткод: | D019 2720 |
| Деталь: | Knob - Registration Roller |
| Парткод: | D019 2822 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Registration Roller - Driven |
| Парткод: | D019 2820 |
| Деталь: | Cleaner Bracket - Registration |
| Парткод: | D019 2757 |
| Деталь: | Front Bracket - Registration Guide |
| Парткод: | D019 2826 |
| Деталь: | Rear Bracket - Registration Guide |
| Парткод: | D019 2827 |
| Деталь: | Left Guide Plate - Registration |
| Парткод: | D019 2690 |
| Деталь: | Bracket:Registration Sensor |
| Парткод: | B090 2698 |
| Деталь: | Registration Sensor |
| Парткод: | AW01 0057 |
| Деталь: | Interface Harness - Regist Sensor |
| Парткод: | D019 5237 |
| Деталь: | Left Guide Plate 2 - Registration |
| Парткод: | D019 2699 |
| Деталь: | Left Guide Plate - Registration |
| Парткод: | D019 2692 |
| Деталь: | Right Guide Plate - Registration |
| Парткод: | D019 2694 |
| Деталь: | Roller:Sponge |
| Парткод: | B209 2665 |
| Деталь: | Snap Ring |
| Парткод: | B090 2686 |
| Деталь: | Snap Ring - M6 |
| Парткод: | B090 2621 |
| Деталь: | Bushing - 8x16x7 |
| Парткод: | AA08 2070 |
| Деталь: | Spring - Driven Registration |
| Парткод: | D019 2829 |
| Деталь: | Bushing - Driven Roller |
| Парткод: | D019 2823 |
| Деталь: | Magnetic Clutch:0.5N M:Z35 |
| Парткод: | D019 1188 |
| Деталь: | O/O (200903 PCIL) |
| Парткод: | D019 1187 |
| Деталь: | X/O MB5 |
| Парткод: | D019 1186 |
| Деталь: | Decal:Operating:B1 Lever |
| Парткод: | D019 2920 |
| Деталь: | Binding Self-tapping Screw:3x10 |
| Парткод: | 0452 3010N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | BUSHING - 6MM |
| Парткод: | 0805 3480 |
| Деталь: | Harness - Paper Exit |
| Парткод: | D019 5206 |
| Деталь: | Harness - ADF |
| Парткод: | D019 5200 |
| Деталь: | Harness - Home Position Sensor |
| Парткод: | D019 5250 |
| Деталь: | Harness:BCU:HPS/AKS:5V |
| Парткод: | D020 5212 |
| Деталь: | Harness - Power Pack |
| Парткод: | D019 5217 |
| Деталь: | Harness - Quenching Lamp |
| Парткод: | D019 5205 |
| Деталь: | Harness:Bypass:Duplex |
| Парткод: | D019 5244 |
| Деталь: | Harness - Main Motor |
| Парткод: | D019 5202 |
| Деталь: | Door Switch Harness |
| Парткод: | D019 5204 |
| Деталь: | Harness - Paper Feed Motor |
| Парткод: | D019 5232 |
| Деталь: | Harness - 1st Paper Feed |
| Парткод: | D019 5233 |
| Деталь: | Harness - 2nd Paper Feed |
| Парткод: | D019 5234 |
| Деталь: | Harness - Paper Size Sensor |
| Парткод: | D019 5231 |
| Деталь: | Harness - IPU Power Source |
| Парткод: | D019 5239 |
| Деталь: | Harness - Paper Feed Clutch |
| Парткод: | D019 5209 |
| Деталь: | Bracket - IOB |
| Парткод: | D019 5838 |
| Деталь: | BCU Board - 33 (D019/D020) |
| Парткод: | D019 5055 |
| Деталь: | X/O MB17 |
| Парткод: | D019 5051 |
| Деталь: | BCU Board - 25 (D017/D018) |
| Парткод: | D019 5056 |
| Деталь: | X/O MB17 |
| Парткод: | D019 5052 |
| Деталь: | PCB:BCU:33 (D085) |
| Парткод: | D085 5055 |
| Деталь: | PCB:BCU:28 (D084) |
| Парткод: | D085 5056 |
| Деталь: | Harness - Interface Unit |
| Парткод: | D019 5241 |
| Деталь: | AC Harness - Main Switch |
| Парткод: | D019 5229 |
| Деталь: | Bracket:Main Switch |
| Парткод: | B206 5823 |
| Деталь: | Power Supply Unit - 120V |
| Парткод: | AZ23 0221 |
| Деталь: | Power Supply Unit - 230V |
| Парткод: | AZ23 0223 |
| Деталь: | AC Harness - Heater |
| Парткод: | D019 5213 |
| Деталь: | Harness - Power Supply Unit |
| Парткод: | D019 5212 |
| Деталь: | Power Supply:Cord:Stopper:NA:Assy |
| Парткод: | D019 5615 |
| Деталь: | x/o MB3 |
| Парткод: | B209 7615 |
| Деталь: | Power Supply Cord:Stopper:EU |
| Парткод: | D019 5631 |
| Деталь: | Power Supply Cord:Stopper:TWN |
| Парткод: | B209 7617 |
| Деталь: | Power Supply Cord:Stopper:CHN |
| Парткод: | D019 5691 |
| Деталь: | x/o MB3 |
| Парткод: | B209 7631 |
| Деталь: | Bracket - Power Supply Cord |
| Парткод: | D019 5831 |
| Деталь: | Choke Coil |
| Парткод: | B121 5018 |
| Деталь: | Harness:Regist Sensor |
| Парткод: | D019 5201 |
| Деталь: | Fan Motor:DC24V 2.4W |
| Парткод: | AX64 0179 |
| Деталь: | Screw - M4X6 |
| Парткод: | AA14 3592 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 0804 6123 |
| Деталь: | Tapping Screw:4x6 |
| Парткод: | 0454 4006Q |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0488 |
| Деталь: | WIRE SADDLE |
| Парткод: | 1105 0292 |
| Деталь: | Spacer - Kgls-16rt |
| Парткод: | 1105 0296 |
| Деталь: | Rocker Switch - AC250V 10A |
| Парткод: | 1204 2477 |
| Деталь: | Fuse (Glass Case) - 10A - 125V |
| Парткод: | 1107 0652 |
| Деталь: | Fuse (Ceramic Case) - 15A - 125V |
| Парткод: | 1107 0629 |
| Деталь: | Fuse - 5A, 125V |
| Парткод: | 1107 0391 |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0487 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | EEPROM:BR24L64-W Added MB7 |
| Парткод: | 1407 6362 |
| Деталь: | Screw:Polished Round/Spring:M3x20 |
| Парткод: | 0954 3020N |
| Деталь: | Fuse:ET-5A |
| Парткод: | 1107 1066 |
| Деталь: | Fuse:HT-8A-N5 |
| Парткод: | 1107 1166 |
| Деталь: | Imaging Unit |
| Парткод: | D019 1900 |
| Деталь: | Shield Glass |
| Парткод: | B206 1977 |
| Деталь: | Decal - LD |
| Парткод: | G029 1980 |
| Деталь: | Supporting Plate:Cover:Imaging Unit |
| Парткод: | B206 1971 |
| Деталь: | Cover:Polygon Scanner:Assy |
| Парткод: | B090 1917 |
| Деталь: | Cover:Optical Housing |
| Парткод: | B090 1938 |
| Деталь: | Polygon Mirror Motor |
| Парткод: | B209 1898 |
| Деталь: | Harness - Polygon Mirror Motor |
| Парткод: | D019 5224 |
| Деталь: | Collar-polygon Motor |
| Парткод: | A232 1916 |
| Деталь: | Plate - Sync.detector Board |
| Парткод: | A267 1944 |
| Деталь: | Harness - Sync Detector |
| Парткод: | D019 5222 |
| Деталь: | Sync.Detector Board |
| Парткод: | D009 5325 |
| Деталь: | MB4 |
| Парткод: | D009 5320 |
| Деталь: | Cylindrical Lens |
| Парткод: | G029 1975 |
| Деталь: | Shield Glass - Polygon Morror Motor |
| Парткод: | G020 1937 |
| Деталь: | Laser Diode Unit |
| Парткод: | D019 1919 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 1105 0508 |
| Деталь: | Binding Self-tapping Screw:3x10 |
| Парткод: | 0452 3010N |
| Деталь: | Fusing Unit - 120V |
| Парткод: | D019 4001 |
| Деталь: | Fusing Unit - 230V |
| Парткод: | D019 4002 |
| Деталь: | Fusing Unit - TWN Added MB13 |
| Парткод: | D019 4003 |
| Деталь: | Upper Frame - Fusing Unit |
| Парткод: | D019 4032 |
| Деталь: | Decal Warning (High Temperature) |
| Парткод: | AA00 0301 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3219 |
| Деталь: | Bracket - Stripper Pawls |
| Парткод: | D019 4101 |
| Деталь: | Tension Spring - Pressure |
| Парткод: | D019 4114 |
| Деталь: | Spring - Fusing Stripper |
| Парткод: | A267 4103 |
| Деталь: | Hot Roller Stripper |
| Парткод: | AE04 4025 |
| Деталь: | Drawer:Fusing:120V |
| Парткод: | D019 5274 |
| Деталь: | Drawer:Fusing:230V |
| Парткод: | D019 5275 |
| Деталь: | Terminal:Heater |
| Парткод: | B090 4092 |
| Деталь: | Fusing Lamp - 120V |
| Парткод: | AX44 0140 |
| Деталь: | Fusing Lamp - 230V |
| Парткод: | AX44 0142 |
| Деталь: | Heater:110V:Main Added MB13 |
| Парткод: | AX44 0256 |
| Деталь: | Fusing Lamp - 120V |
| Парткод: | AX44 0141 |
| Деталь: | Fusing Lamp - 230V |
| Парткод: | AX44 0143 |
| Деталь: | Heater:110V:Sub Added MB13 |
| Парткод: | AX44 0257 |
| Деталь: | Bearing 30x42x7 |
| Парткод: | G052 4618 |
| Деталь: | C Ring - Hot Roller |
| Парткод: | B031 4056 |
| Деталь: | Gear - 48Z |
| Парткод: | AB01 1400 |
| Деталь: | Pressure Roller:Mm27 |
| Парткод: | AE02 0161 |
| Деталь: | Ball Bearing - 8x19x6 |
| Парткод: | AE03 0030 |
| Деталь: | Spring:Flange:Pressure Roller |
| Парткод: | B091 4066 |
| Деталь: | KNOB SCREW:FIX:FUSING |
| Парткод: | D019 4161 |
| Деталь: | Circlip Stopper |
| Парткод: | B209 4071 |
| Деталь: | Guide:Harness:Plate |
| Парткод: | B206 4077 |
| Деталь: | Hot Roller:MM40:T0.4 |
| Парткод: | AE01 1103 |
| Деталь: | Philips Screw - M3x8 |
| Парткод: | B051 4050 |
| Деталь: | Spring:Open And Close:Guide Added MB12 |
| Парткод: | D019 4158 |
| Деталь: | Guide Plate:Fusing:Upper Added MB12 |
| Парткод: | D019 4156 |
| Деталь: | DECAL:GRIP:GUIDE PLATE:FUSING EXIT |
| Парткод: | D019 4181 |
| Деталь: | DECAL:GRIP:GUIDE PLATE:FUSING EXIT |
| Парткод: | D019 4184 |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 0804 6123 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | PCU Unit |
| Парткод: | B205 0151 |
| Деталь: | Pickoff Pawl |
| Парткод: | B039 2335 |
| Деталь: | Blade:Cleaning |
| Парткод: | AD04 1114 |
| Деталь: | PCU Seal |
| Парткод: | A267 1059 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3444 |
| Деталь: | Roller:Charge:A3 |
| Парткод: | AD02 7018 |
| Деталь: | Charge Cleaner Brush Roller |
| Парткод: | AD04 2058 |
| Деталь: | Charge Roller Spring |
| Парткод: | B039 2287 |
| Деталь: | Front Pressure Arm - Charge Roller |
| Парткод: | B039 2292 |
| Деталь: | Snap Ring Deleted MB14 |
| Парткод: | B090 2686 |
| Деталь: | Pin - Front Pressure Arm |
| Парткод: | B039 2293 |
| Деталь: | Arm:Pressure:Charge:Rear |
| Парткод: | B209 3174 |
| Деталь: | Electrode Plate:Roller:Charge:Assy |
| Парткод: | B209 3175 |
| Деталь: | Clip - OPC DRUM |
| Парткод: | B039 2350 |
| Деталь: | Joint:Development |
| Парткод: | B209 3440 |
| Деталь: | OPC Drum |
| Парткод: | B039 9510 |
| Деталь: | Development Roller Assembly |
| Парткод: | B209 3320 |
| Деталь: | Idler Gear |
| Парткод: | B039 3062 |
| Деталь: | Development Roller Gear |
| Парткод: | B039 3060 |
| Деталь: | Development Case |
| Парткод: | B209 3370 |
| Деталь: | Shield:Toner Supply:Entrance |
| Парткод: | B209 3196 |
| Деталь: | Drum Stay:Rear |
| Парткод: | B209 3233 |
| Деталь: | Development Roller Case |
| Парткод: | B209 3360 |
| Деталь: | Drum Stay:Front |
| Парткод: | B209 3215 |
| Деталь: | Developer Type 28 Black MB2 |
| Парткод: | B121 9640 |
| Деталь: | Drum Shutter ADD (200904 PCIL) |
| Парткод: | B039 2343 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Binding Self-tapping Screw:3x6 |
| Парткод: | 0452 3006N |
| Деталь: | Bracket:Paper End Sensor |
| Парткод: | B090 2805 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Interface Harness - Paper End |
| Парткод: | D019 5215 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | A267 2803 |
| Деталь: | Stopper Paper Feed Roller |
| Парткод: | B093 2935 |
| Деталь: | Snap Ring |
| Парткод: | B090 2686 |
| Деталь: | Guide Plate Paper Feed Roller 2 Assy |
| Парткод: | B093 2808 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A267 2751 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | A267 2754 |
| Деталь: | Cushion - Roller Guide 2 |
| Парткод: | B209 2814 |
| Деталь: | Bracket:Photointerruptor |
| Парткод: | B206 2660 |
| Деталь: | Photointerruptor:Vertical Transport |
| Парткод: | AW02 0173 |
| Деталь: | Link:Damper:Assy |
| Парткод: | D019 2846 |
| Деталь: | Roller:Drive |
| Парткод: | B097 2668 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0252 |
| Деталь: | Guide Plate:Friction Pad |
| Парткод: | B206 2842 |
| Деталь: | Bracket - Guide Plate No.2 |
| Парткод: | D019 2587 |
| Деталь: | Cushion - Link |
| Парткод: | AA16 1143 |
| Деталь: | Heater:NA:Assy Added MB8 |
| Парткод: | D019 2598 |
| Деталь: | Heater:EU:Assy Added MB8 |
| Парткод: | D019 2599 |
| Деталь: | Main Switch Decal - NA |
| Парткод: | D010 7450 |
| Деталь: | Main Switch Decal - EU |
| Парткод: | D010 7451 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | BUSHING - 6MM |
| Парткод: | 0805 3480 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 1105 0522 |
| Деталь: | Clamp:LWS-1211Z Added MB8 |
| Парткод: | 1105 0488 |
| Деталь: | Screw:Spring Washer:M3x6 Added MB8 |
| Парткод: | 0950 3006N |
| Деталь: | Harness - SBU MS |
| Парткод: | D019 5245 |
| Деталь: | Scanner interface cable |
| Парткод: | B238 5345 |
| Деталь: | X/O (200911PCIL) |
| Парткод: | B238 5372 |
| Деталь: | SIU Board |
| Парткод: | D019 5130 |
| Деталь: | SIU Board - CS |
| Парткод: | D020 5162 |
| Деталь: | SIU Bracket |
| Парткод: | D019 5871 |
| Деталь: | Bracket - IPU |
| Парткод: | D019 5850 |
| Деталь: | PCB:Image Processing Unit |
| Парткод: | D019 5152 |
| Деталь: | Harness - Laser Diode |
| Парткод: | D019 5223 |
| Деталь: | Harness - OPU MS |
| Парткод: | D019 5226 |
| Деталь: | Harness:Operation Sub-unit:24V |
| Парткод: | D020 5211 |
| Деталь: | FFC Harness 2 - IPU |
| Парткод: | D019 5221 |
| Деталь: | FFC Harness 1 - IPU |
| Парткод: | D019 5210 |
| Деталь: | Cover - IPU FFC |
| Парткод: | D019 5853 |
| Деталь: | Bracket 2 - Control Board |
| Парткод: | D019 5859 |
| Деталь: | Controller Board - 33 MS (D019) |
| Парткод: | D019 5310 |
| Деталь: | Controller Board - 33 CS (D020) |
| Парткод: | D020 5310 |
| Деталь: | Controller Board - 25 MS (D017) |
| Парткод: | D019 5311 |
| Деталь: | Controller Board - 25 CS (D018) |
| Парткод: | D020 5311 |
| Деталь: | PCB:Controller:33 (D085) |
| Парткод: | D085 5310 |
| Деталь: | PCB:Controller:28 (D084) |
| Парткод: | D085 5311 |
| Деталь: | NVRAM |
| Парткод: | D009 9590 |
| Деталь: | Right Rail - Small |
| Парткод: | D009 5899 |
| Деталь: | Left Rail - Fax Control Unit |
| Парткод: | D009 5891 |
| Деталь: | Panel - Fax |
| Парткод: | D019 5890 |
| Деталь: | Bracket - Control Board |
| Парткод: | D019 5868 |
| Деталь: | Panel:Interface |
| Парткод: | B209 5867 |
| Деталь: | PCB:DDR1-DIMM-32B:256MB:Assy |
| Парткод: | B585 5130 |
| Деталь: | PCB:DDR1-DIMM-32B:512MB:Assy |
| Парткод: | B585 5140 |
| Деталь: | PCB - HDD |
| Парткод: | D362 5170 |
| Деталь: | Harness - HDD |
| Парткод: | D362 5132 |
| Деталь: | Cable - HDD Power |
| Парткод: | D362 5131 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | AA14 3848 |
| Деталь: | Rubber Cushion |
| Парткод: | AA16 1125 |
| Деталь: | HDD bracket |
| Парткод: | D362 1140 |
| Деталь: | HDD:80GB:MHZ2080BH:FUJITSU |
| Парткод: | M308 5130 |
| Деталь: | O/O (200906 PCIL) |
| Парткод: | M344 5130 |
| Деталь: | O/O MB10 |
| Парткод: | D362 5130 |
| Деталь: | Thermally Conductive Sheet |
| Парткод: | D019 5899 |
| Деталь: | SD-Card:VM:EXP:Assy (D084/D085) |
| Парткод: | D092 5910 |
| Деталь: | SD-Card - RPCS (D017/D018/D019/D020) |
| Парткод: | D383 5010 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 0804 6123 |
| Деталь: | BUSHING - VERTICAL TRANSPORT |
| Парткод: | D019 2736 |
| Деталь: | Spring - Transport |
| Парткод: | D019 2734 |
| Деталь: | Roller:Pull Out:Option Tray |
| Парткод: | B090 2742 |
| Деталь: | Guide Plate - Vertical Transport |
| Парткод: | D019 2731 |
| Деталь: | Driven Roller - Vertical Transport |
| Парткод: | D019 2737 |
| Деталь: | Guide Plate:Exit:Vertical Transport |
| Парткод: | D019 2707 |
| Деталь: | Rear Lever - Transfer |
| Парткод: | D019 2703 |
| Деталь: | Rear Lever - Fusing |
| Парткод: | D019 2705 |
| Деталь: | Front Lever - Transfer |
| Парткод: | D019 2704 |
| Деталь: | Front Lever - Transfer |
| Парткод: | D019 2706 |
| Деталь: | Frame - Vertical Transportr |
| Парткод: | D019 2710 |
| Деталь: | Release Pawl - Rear |
| Парткод: | D019 2722 |
| Деталь: | Roller - Lever |
| Парткод: | A267 3958 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | D019 2727 |
| Деталь: | Bracket:UN Lock MB15 |
| Парткод: | D019 2725 |
| Деталь: | Release Grip |
| Парткод: | D019 2723 |
| Деталь: | Release Pawl - Front |
| Парткод: | D019 2728 |
| Деталь: | Bracket:Manual Feed |
| Парткод: | D019 2716 |
| Деталь: | Link - Vertical Transport |
| Парткод: | D019 2761 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Upper Cover - Vertical Transport |
| Парткод: | D019 2841 |
| Деталь: | Middle Cover - Vertical Transport |
| Парткод: | D019 2842 |
| Деталь: | Lower Cover - Vertical Transport |
| Парткод: | D019 2843 |
| Деталь: | Screw:DIA5:Hinge |
| Парткод: | D019 2764 |
| Деталь: | TENSION SPRING |
| Парткод: | D019 2724 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Decal:Energy-Star |
| Парткод: | AA00 1477 |
| Деталь: | Hinge - Front Cover |
| Парткод: | G020 1332 |
| Деталь: | Magnet Catch:Door:Front |
| Парткод: | B090 1264 |
| Деталь: | Model Name Plate:RIC:2550B |
| Парткод: | D017 8600 |
| Деталь: | Model Name Plate:SVN:9025B |
| Парткод: | D017 8601 |
| Деталь: | Model Name Plate:LAN:LD425B |
| Парткод: | D017 8602 |
| Деталь: | Model Name Plate:LAN:2550B |
| Парткод: | D017 8603 |
| Деталь: | Model Name Plate:NSA:2550B |
| Парткод: | D017 8604 |
| Деталь: | Model Name Plate:REX:2550B |
| Парткод: | D017 8605 |
| Деталь: | Model Name Plate:GES:2550B:EU |
| Парткод: | D017 8606 |
| Деталь: | Model Name Plate:GES:2550B |
| Парткод: | D017 8607 |
| Деталь: | Model Name Plate:INF:2550B |
| Парткод: | D017 8608 |
| Деталь: | Model Name Plate:RIC:2591 |
| Парткод: | D017 8609 |
| Деталь: | Model Name Plate:GES:2591 |
| Парткод: | D017 8610 |
| Деталь: | Model Name Plate:RIC:2550 |
| Парткод: | D018 8600 |
| Деталь: | Model Name Plate:SVN:9025 |
| Парткод: | D018 8601 |
| Деталь: | Model Name Plate:LAN:LD425 |
| Парткод: | D018 8602 |
| Деталь: | Model Name Plate:LAN:2550 |
| Парткод: | D018 8603 |
| Деталь: | Model Name Plate:NSA:2550 |
| Парткод: | D018 8604 |
| Деталь: | Model Name Plate:REX:2550 |
| Парткод: | D018 8605 |
| Деталь: | Model Name Plate:GES:2550:EU |
| Парткод: | D018 8606 |
| Деталь: | Model Name Plate:GES:2550 |
| Парткод: | D018 8607 |
| Деталь: | Model Name Plate:INF:2550 |
| Парткод: | D018 8608 |
| Деталь: | Model Name Plate:RIC:3350B |
| Парткод: | D019 8600 |
| Деталь: | Model Name Plate:SVN:9033B |
| Парткод: | D019 8601 |
| Деталь: | Model Name Plate:LAN:LD433B |
| Парткод: | D019 8602 |
| Деталь: | Model Name Plate:LAN:3350B |
| Парткод: | D019 8603 |
| Деталь: | Model Name Plate:NSA:3350B |
| Парткод: | D019 8604 |
| Деталь: | Model Name Plate:REX:3350B |
| Парткод: | D019 8605 |
| Деталь: | Model Name Plate:GES:3350B:EU |
| Парткод: | D019 8606 |
| Деталь: | Model Name Plate:GES:3350B |
| Парткод: | D019 8607 |
| Деталь: | Model Name Plate:INF:3350B |
| Парткод: | D019 8608 |
| Деталь: | Model Name Plate:RIC:3391 |
| Парткод: | D019 8609 |
| Деталь: | Model Name Plate:GES:3391 |
| Парткод: | D019 8610 |
| Деталь: | Model Name Plate:RIC:3350 |
| Парткод: | D020 8600 |
| Деталь: | Model Name Plate:SVN:9033 |
| Парткод: | D020 8601 |
| Деталь: | Model Name Plate:LAN:LD433 |
| Парткод: | D020 8602 |
| Деталь: | Model Name Plate:LAN:3350 |
| Парткод: | D020 8603 |
| Деталь: | Model Name Plate:NSA:3350 |
| Парткод: | D020 8604 |
| Деталь: | Model Name Plate:REX:3350 |
| Парткод: | D020 8605 |
| Деталь: | Model Name Plate:GES:3350:EU |
| Парткод: | D020 8606 |
| Деталь: | Model Name Plate:GES:3350 |
| Парткод: | D020 8607 |
| Деталь: | Model Name Plate:INF:3350 |
| Парткод: | D020 8608 |
| Деталь: | Sheet:EMBLEM:28:RIC (D084) |
| Парткод: | D084 8600 |
| Деталь: | Sheet:EMBLEM:28:NAS (D084) |
| Парткод: | D084 8604 |
| Деталь: | Sheet:EMBLEM:28:REX (D084) |
| Парткод: | D084 8605 |
| Деталь: | Sheet:EMBLEM:28:GES:EU (D084) |
| Парткод: | D084 8606 |
| Деталь: | Sheet:EMBLEM:28:GES:NA (D084) |
| Парткод: | D084 8607 |
| Деталь: | Sheet:EMBLEM:28:INF (D084) |
| Парткод: | D084 8608 |
| Деталь: | Sheet:EMBLEM:33:RIC (D085) |
| Парткод: | D085 8600 |
| Деталь: | Sheet:EMBLEM:33:NAS (D085) |
| Парткод: | D085 8604 |
| Деталь: | Sheet:EMBLEM:33:REX (D085) |
| Парткод: | D085 8605 |
| Деталь: | Sheet:EMBLEM:33:GES:EU (D085) |
| Парткод: | D085 8606 |
| Деталь: | Sheet:EMBLEM:33:GES:NA (D085) |
| Парткод: | D085 8607 |
| Деталь: | Sheet:EMBLEM:33:INF (D085) |
| Парткод: | D085 8608 |
| Деталь: | Cover:Main Switch |
| Парткод: | B090 1302 |
| Деталь: | Front Door - NA |
| Парткод: | D019 1261 |
| Деталь: | Front Door - EU |
| Парткод: | D019 1266 |
| Деталь: | Shield Duct |
| Парткод: | A267 1342 |
| Деталь: | End Fence - Paper |
| Парткод: | D019 1349 |
| Деталь: | Support Tray - Paper Exit |
| Парткод: | D019 1348 |
| Деталь: | Exit cover |
| Парткод: | D019 1343 |
| Деталь: | Exit Cover EU |
| Парткод: | D019 1361 |
| Деталь: | Panel:Logo |
| Парткод: | B132 1531 |
| Деталь: | Decal - Power Source:Off |
| Парткод: | B132 1573 |
| Деталь: | Decal:Power Source:Off:DOM |
| Парткод: | B132 1572 |
| Деталь: | Magnet Catch:44.1n |
| Парткод: | AG07 0504 |
| Деталь: | FRONT COVER |
| Парткод: | D019 1330 |
| Деталь: | Sheet:Operation Instructions |
| Парткод: | D019 1268 |
| Деталь: | Cover:Shield Glass:C |
| Парткод: | B090 1265 |
| Деталь: | Upper Cover - Paper Exit NA |
| Парткод: | D019 1308 |
| Деталь: | Upper Exit Cover - EU |
| Парткод: | D019 1328 |
| Деталь: | Cap - LED |
| Парткод: | A267 1325 |
| Деталь: | Front Cover - Right Upper NA |
| Парткод: | D019 1326 |
| Деталь: | Front Cover - Right Upper EU |
| Парткод: | D019 1329 |
| Деталь: | PCU Unit |
| Парткод: | B205 0151 |
| Деталь: | Guide Plate:Scanner:Packing |
| Парткод: | D019 1099 |
| Деталь: | Cloth Holder |
| Парткод: | B065 1371 |
| Деталь: | Cloth - DF Exposure Glass |
| Парткод: | B065 1374 |
| Деталь: | Decal - Paper Size |
| Парткод: | B238 2524 |
| Деталь: | Seal:Caution:18Languages (D084/D085) |
| Парткод: | D376 7901 |
| Деталь: | Sheet:EULA:18Languages:CHN (D084/D085) |
| Парткод: | D376 7905 |
| Деталь: | Cover:Front:Right Upper:NA |
| Парткод: | D019 1321 |
| Деталь: | Front Cover - Right Upper EU |
| Парткод: | D019 1322 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0434 0082N |
| Деталь: | Bracket:Paper End Sensor |
| Парткод: | B090 2805 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Interface Harness - Paper End |
| Парткод: | D019 5215 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | A267 2803 |
| Деталь: | Stopper - Paper Feed Roller |
| Парткод: | D019 2807 |
| Деталь: | Snap Ring |
| Парткод: | B090 2686 |
| Деталь: | Guide Plate - Paper Feed Roller 1 |
| Парткод: | D019 2804 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A267 2751 |
| Деталь: | Shaft - Paper Feed Roller |
| Парткод: | A267 2754 |
| Деталь: | Bracket:Photointerruptor |
| Парткод: | B090 2663 |
| Деталь: | Photointerruptor:Vertical Transport |
| Парткод: | AW02 0173 |
| Деталь: | Guide Plate:Friction Pad:Upper |
| Парткод: | B206 2828 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0252 |
| Деталь: | Upper Drive Roller |
| Парткод: | D019 2682 |
| Деталь: | Roller:Sponge |
| Парткод: | B209 2665 |
| Деталь: | Spacer:Supporter:Right |
| Парткод: | D010 2640 |
| Деталь: | Positioning Cap - Short |
| Парткод: | B223 2714 |
| Деталь: | Cushion - Link |
| Парткод: | AA16 1143 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | BUSHING - 6MM |
| Парткод: | 0805 3480 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 1105 0522 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0453 3006N |
| Деталь: | Tension Roller |
| Парткод: | AF04 0567 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0566 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | A267 4483 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | A267 4474 |
| Деталь: | Stopper:Spring Plate:Outer |
| Парткод: | B091 4487 |
| Деталь: | Stopper:Spring Plate |
| Парткод: | B091 4486 |
| Деталь: | Shaft - Paper Overflow |
| Парткод: | A267 4479 |
| Деталь: | Feeler - Paper Overflow |
| Парткод: | A267 4478 |
| Деталь: | Feeler - Paper Feed Sensor |
| Парткод: | A267 4476 |
| Деталь: | EXIT ROLLER |
| Парткод: | B209 4475 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | AA12 0094 |
| Деталь: | Cover:Paper Feed Sensor |
| Парткод: | B090 4489 |
| Деталь: | Harness - Paper Feed Sensor |
| Парткод: | D019 5207 |
| Деталь: | Photointerruptor |
| Парткод: | B207 1886 |
| Деталь: | Guide Plate - Exit |
| Парткод: | D019 4454 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1404 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 2112 |
| Деталь: | Stay - Exit Unit |
| Парткод: | D019 4452 |
| Деталь: | Bracket:Stopper |
| Парткод: | D019 1058 |
| Деталь: | Guide:Stopper |
| Парткод: | D019 1059 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | BUSHING - 6MM |
| Парткод: | 0805 3480 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Bracket:Protect:Side Plate:Left Rear |
| Парткод: | B090 1085 |
| Деталь: | Guide Plate:Duct:Exhaust:C |
| Парткод: | D019 1106 |
| Деталь: | Fan Motor - Mm80 |
| Парткод: | B209 1105 |
| Деталь: | Duct:Fan Motor |
| Парткод: | B209 1102 |
| Деталь: | Bracket:Micro Switch |
| Парткод: | B090 5813 |
| Деталь: | Tension Spring:Door Switch |
| Парткод: | B091 5821 |
| Деталь: | Hinge - Front Door |
| Парткод: | D019 1088 |
| Деталь: | Positioning Bracket - Laser Unit |
| Парткод: | A267 1930 |
| Деталь: | Left Grip Cover |
| Парткод: | D019 2565 |
| Деталь: | Left Grip |
| Парткод: | D019 2564 |
| Деталь: | Compression Spring:Door Switch |
| Парткод: | B091 5820 |
| Деталь: | Lever:Door Switch:Assy |
| Парткод: | B092 5815 |
| Деталь: | Rubber Pad - H5 |
| Парткод: | AH01 0009 |
| Деталь: | PCU Seal |
| Парткод: | A267 1059 |
| Деталь: | Bracket - PCU |
| Парткод: | D019 1091 |
| Деталь: | Right Front Grip |
| Парткод: | D019 2562 |
| Деталь: | Right Front Grip |
| Парткод: | D019 2566 |
| Деталь: | Cover - Right Front Grip |
| Парткод: | D019 2567 |
| Деталь: | Support Frame - Right Front |
| Парткод: | D019 1078 |
| Деталь: | Scanner Stay - Right Lower |
| Парткод: | D019 1081 |
| Деталь: | X/O MB18 |
| Парткод: | D019 1080 |
| Деталь: | Support Frame - Right Rear |
| Парткод: | D019 1079 |
| Деталь: | Grip Bracket - Rear Left |
| Парткод: | D019 2576 |
| Деталь: | Guide Plate:Lengthwise:Left Rear |
| Парткод: | D019 1083 |
| Деталь: | Arm - Scanner |
| Парткод: | D019 1093 |
| Деталь: | Sponge Side Plate Rear (D018/D020) Added MB18 |
| Парткод: | D019 1075 |
| Деталь: | Seal Arm Scanner Added MB18 |
| Парткод: | D019 1086 |
| Деталь: | SUPPORTER:LEFT:ASSY |
| Парткод: | D010 2554 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw:Round Point:M3x6 |
| Парткод: | 0802 5291 |
| Деталь: | Pan Head Screw:M4x30 |
| Парткод: | 0314 0300N |
| Деталь: | Pan Head Screw:M3x35 |
| Парткод: | 0313 0350N |
| Деталь: | MICRO SWITCH |
| Парткод: | 1204 2510 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 0451 4008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | TONER SUPPLY UNIT |
| Парткод: | D019 3501 |
| Деталь: | Cam:Handle |
| Парткод: | B090 3605 |
| Деталь: | Shaft:Chuck |
| Парткод: | B090 3572 |
| Деталь: | Toner Slider |
| Парткод: | A184 3422 |
| Деталь: | Tapping Screw-M3x8 |
| Парткод: | B044 3191 |
| Деталь: | Chuck Spring - Tonner Bottle |
| Парткод: | A267 3556 |
| Деталь: | Slider:Assy |
| Парткод: | B090 3573 |
| Деталь: | Chuck:Bottle |
| Парткод: | B090 3571 |
| Деталь: | Cover:Toner Bottle:Assy |
| Парткод: | B090 3560 |
| Деталь: | Motor Spacer - Toner Bottle |
| Парткод: | B027 3620 |
| Деталь: | Toner Bottle Motor |
| Парткод: | B209 3616 |
| Деталь: | Bracket DC Motor Toner Bottle Z EXP |
| Парткод: | B090 7440 |
| Деталь: | Guide Plate:Toner Supply Unit:Assy |
| Парткод: | D019 1054 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Harness - New Parts Sensor |
| Парткод: | D019 5203 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | 1st Scanner Assy |
| Парткод: | D019 1817 |
| Деталь: | 1st Scanner Assy |
| Парткод: | B180 1817 |
| Деталь: | Xenon Lamp:Monochrome |
| Парткод: | D019 1830 |
| Деталь: | Xenon Lamp - DIA10 |
| Парткод: | B238 1820 |
| Деталь: | Wire Clamp |
| Парткод: | A193 1766 |
| Деталь: | Clamp - Rear Wire |
| Парткод: | A193 1769 |
| Деталь: | Original Sensor - 66mm |
| Парткод: | AW01 0133 |
| Деталь: | 1st Mirror (MS model) |
| Парткод: | AC03 0142 |
| Деталь: | Mirror:No.1 (CS model) |
| Парткод: | AC03 0169 |
| Деталь: | 1st Mirror Holder |
| Парткод: | A193 1767 |
| Деталь: | Inner Cover - Scanner (MS model) |
| Парткод: | D019 1823 |
| Деталь: | Inner Cover - Scanner (CS model) |
| Парткод: | B238 1823 |
| Деталь: | Original Sensor - 48mm |
| Парткод: | AW01 0134 |
| Деталь: | Bracket:Original Sensor |
| Парткод: | D019 1827 |
| Деталь: | Original Sensor Bracket |
| Парткод: | B238 1827 |
| Деталь: | Lens Unit |
| Парткод: | D019 1703 |
| Деталь: | MB6 |
| Парткод: | D019 1698 |
| Деталь: | Lens Unit |
| Парткод: | D020 1703 |
| Деталь: | MB6 |
| Парткод: | D020 1698 |
| Деталь: | Stabilizer:Xenon Lamp |
| Парткод: | AZ50 0068 |
| Деталь: | Stabilizer |
| Парткод: | B238 1821 |
| Деталь: | HARNESS COVER |
| Парткод: | D019 1753 |
| Деталь: | Inner Cover - Sensor |
| Парткод: | B238 1753 |
| Деталь: | Harness - SBU MS |
| Парткод: | D019 5245 |
| Деталь: | Scanner interface cable |
| Парткод: | B238 5345 |
| Деталь: | X/O (200911PCIL) |
| Парткод: | B238 5372 |
| Деталь: | Harness - Exposure Lamp MS |
| Парткод: | D019 5252 |
| Деталь: | Harness:SIO:LAMP |
| Парткод: | D025 5214 |
| Деталь: | Harness - APS MS |
| Парткод: | D019 5230 |
| Деталь: | Harness - APS |
| Парткод: | B238 5367 |
| Деталь: | SBU Ground Plate |
| Парткод: | B238 5344 |
| Деталь: | Ground Plate - Carriage |
| Парткод: | B238 1812 |
| Деталь: | REFLECTOR |
| Парткод: | A100 1714 |
| Деталь: | Carriage:No.1:Assy |
| Парткод: | B238 1676 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0802 5299 |
| Деталь: | CLAMP |
| Парткод: | 1105 0516 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Clamp - JCC-1R |
| Парткод: | 1105 0622 |
| Деталь: | PCB Stud |
| Парткод: | 1105 0195 |
| Деталь: | Left Upper Cover - NA |
| Парткод: | D019 1283 |
| Деталь: | Left Upper Cover - EU |
| Парткод: | D019 1357 |
| Деталь: | Left Rear - NA |
| Парткод: | D019 1285 |
| Деталь: | Left Rear Cover - EU |
| Парткод: | D019 1359 |
| Деталь: | Cover:Left Rear:MONO |
| Парткод: | D019 1282 |
| Деталь: | Cover:Left Rear:EU:Color |
| Парткод: | D019 1379 |
| Деталь: | Left Cover - NA |
| Парткод: | D019 1284 |
| Деталь: | Left Cover - EU |
| Парткод: | D019 1358 |
| Деталь: | Rear Cover - Paper Exit NA |
| Парткод: | D019 1307 |
| Деталь: | Rear Exit Cover - EU |
| Парткод: | D019 1327 |
| Деталь: | Lower Cover - Paper Exit |
| Парткод: | D019 1346 |
| Деталь: | Lower Exit Cover - EU |
| Парткод: | D019 1347 |
| Деталь: | Right Front Cover - NA |
| Парткод: | D019 1279 |
| Деталь: | Right Front Cover - EU |
| Парткод: | D019 1356 |
| Деталь: | Right Rear Cover - NA |
| Парткод: | D019 1278 |
| Деталь: | Right Rear Cover - EU |
| Парткод: | D019 1355 |
| Деталь: | Connector Cap - Vertical Transport |
| Парткод: | D019 1371 |
| Деталь: | Right Cover - NA |
| Парткод: | D019 1277 |
| Деталь: | Right Cover - EU |
| Парткод: | D019 1354 |
| Деталь: | Cap:Heater:Dehumidifier |
| Парткод: | B090 1375 |
| Деталь: | Rivet - M6 |
| Парткод: | B039 1367 |
| Деталь: | RIGHT REAR COVER |
| Парткод: | D019 1296 |
| Деталь: | Right Rear Cover - Lower EU |
| Парткод: | D019 1393 |
| Деталь: | CAP:38x77 |
| Парткод: | D019 1365 |
| Деталь: | O/O (200906 PCIL) |
| Парткод: | B024 1365 |
| Деталь: | REAR COVER |
| Парткод: | D019 1294 |
| Деталь: | Rear Cover - EU |
| Парткод: | D019 1390 |
| Деталь: | Cap - Paper Feed Table NA |
| Парткод: | D019 1376 |
| Деталь: | Cap - Paper Feed Table EU |
| Парткод: | D019 1378 |
| Деталь: | Left Scanner Cover - NA |
| Парткод: | D019 1254 |
| Деталь: | Left Scanner Cover - EU |
| Парткод: | D019 1350 |
| Деталь: | Cover:Scanner:Front Upper:NA |
| Парткод: | D019 1257 |
| Деталь: | Front Scanner Cover - EU |
| Парткод: | D019 1353 |
| Деталь: | Upper Scanner Cover - Front NA |
| Парткод: | D019 1256 |
| Деталь: | Right Scanner Cover - EU |
| Парткод: | D019 1352 |
| Деталь: | Upper Scanner Cover - Rear NA |
| Парткод: | D019 1255 |
| Деталь: | Rear Scanner Cover - EU |
| Парткод: | D019 1351 |
| Деталь: | Scanner Cover - Rear EU |
| Парткод: | B237 1367 |
| Деталь: | Cover:Paper Feed Sub-Unit:Rear Added MB16 |
| Парткод: | D019 1296 |
| Деталь: | Cover:Paper Feed Sub-Unit:Rear:EU Added MB16 |
| Парткод: | D019 1393 |
| Деталь: | Right Rear Cover - Lower Only NA |
| Парткод: | D019 1295 |
| Деталь: | Right Rear Cover - Lower Only EU |
| Парткод: | D019 1391 |
| Деталь: | Bracket:Scanning:Rear Left |
| Парткод: | D019 1077 |
| Деталь: | Bracket:Scanning:Front Left |
| Парткод: | D019 1087 |
| Деталь: | Bracket:Scanning:Front Right |
| Парткод: | D019 1095 |
| Деталь: | Bracket:Scanning:Rear Right |
| Парткод: | D019 1098 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Scale:Left:A |
| Парткод: | D019 1801 |
| Деталь: | Scale - Left (A) |
| Парткод: | B238 1801 |
| Деталь: | Exposure Glass |
| Парткод: | B238 1795 |
| Деталь: | Shaft:Scale |
| Парткод: | B390 1759 |
| Деталь: | Scale:Left:B:NA:Assy |
| Парткод: | D019 1713 |
| Деталь: | Scale:Left:B:Assy |
| Парткод: | D019 1723 |
| Деталь: | Scale - Left B NA |
| Парткод: | B237 1713 |
| Деталь: | Scale - Left (B) |
| Парткод: | B238 1713 |
| Деталь: | Rear Scale |
| Парткод: | D019 1751 |
| Деталь: | Scale - Inner Back |
| Парткод: | B229 1751 |
| Деталь: | Exposure Glass |
| Парткод: | A250 1752 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 5442 1924 |
| Деталь: | Cushion Glass |
| Парткод: | B093 1862 |
| Деталь: | Seal:Exposure Glass |
| Парткод: | B238 1845 |
| Деталь: | Photointerruptor:Flat:PICH2mm:M4 |
| Парткод: | AW02 0146 |
| Деталь: | Harness - Home Position Sensor |
| Парткод: | D019 5250 |
| Деталь: | Harness:BCU:HPS/AKS:5V |
| Парткод: | D020 5212 |
| Деталь: | Sensor Shielding Plate |
| Парткод: | G570 1225 |
| Деталь: | Grounding Plate - Upper Rear |
| Парткод: | A267 1089 |
| Деталь: | GASKET |
| Парткод: | D019 5849 |
| Деталь: | Grounding Plate - Lower Right |
| Парткод: | A267 1090 |
| Деталь: | Bracket:Document Feeder |
| Парткод: | D019 1803 |
| Деталь: | Bracket:Scale:Left:Assy |
| Парткод: | B238 1692 |
| Деталь: | Frame:Rear (MS models) Added MB9 |
| Парткод: | D019 1785 |
| Деталь: | Frame:Rear (CS models) Added MB9 |
| Парткод: | B238 1785 |
| Деталь: | Frame:Front |
| Парткод: | B238 1784 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Cover:Sensor:AKS |
| Парткод: | D019 1789 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0453 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Screw - M4X12 |
| Парткод: | 0314 0120N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Front Terminal Plate - Thermostat |
| Парткод: | B027 4091 |
| Деталь: | Thermostat Housing |
| Парткод: | B209 4094 |
| Деталь: | Thermostat - 180c |
| Парткод: | B209 4095 |
| Деталь: | Grip - Pressure Change |
| Парткод: | D019 4112 |
| Деталь: | Front Lever - Pressure Roller |
| Парткод: | D019 4116 |
| Деталь: | Front Side Plate - Fusing |
| Парткод: | D019 4121 |
| Деталь: | Lever:Lock:Pressure |
| Парткод: | D019 4197 |
| Деталь: | Lever:Pressure Release:Front:Assy |
| Парткод: | D019 4171 |
| Деталь: | End Ring:Spring:DIA4 Deleted RTB40 |
| Парткод: | D019 4166 |
| Деталь: | Roller:Lever:Pressure |
| Парткод: | D019 4194 |
| Деталь: | Screw:Drawer |
| Парткод: | D019 4792 |
| Деталь: | Lever:Pressure Release:Rear:Assy |
| Парткод: | D019 4191 |
| Деталь: | Shaft - Pressure Lever |
| Парткод: | D019 4111 |
| Деталь: | Terminal Plate - Thermostat |
| Парткод: | B027 4092 |
| Деталь: | Rear Terminal Plate - Thermostat |
| Парткод: | B027 4093 |
| Деталь: | Harness - Sheet |
| Парткод: | B027 4079 |
| Деталь: | Cover:Thermostat |
| Парткод: | B206 4078 |
| Деталь: | Compression Spring - 5N |
| Парткод: | B091 4084 |
| Деталь: | Roller Busing |
| Парткод: | AA08 2073 |
| Деталь: | Fusing Cleaning Roller |
| Парткод: | AE04 2029 |
| Деталь: | Link:Release:Drive |
| Парткод: | B090 4082 |
| Деталь: | Lever:Release:Drive |
| Парткод: | B090 4083 |
| Деталь: | Spring:Release:Drive |
| Парткод: | B207 4081 |
| Деталь: | Rear Side Plate - Fusing |
| Парткод: | D019 4125 |
| Деталь: | Decal:Warning (High Temperature):C |
| Парткод: | D019 4183 |
| Деталь: | Fusing Entrance Guide |
| Парткод: | A267 4085 |
| Деталь: | Lower Frame - Fusing Unit |
| Парткод: | D019 4072 |
| Деталь: | Fusing Ground Plate - Entrance |
| Парткод: | A267 4086 |
| Деталь: | Thermistor - Rear |
| Парткод: | AW10 0053 |
| Деталь: | Holder:Thermistor |
| Парткод: | B090 4099 |
| Деталь: | Spur |
| Парткод: | A232 2374 |
| Деталь: | Spacer - Safety Switch |
| Парткод: | A267 4076 |
| Деталь: | Rear Lever - Pressure Roller |
| Парткод: | D019 4117 |
| Деталь: | Decal:Exchange Indication:Envelope |
| Парткод: | D019 4182 |
| Деталь: | Sheet:Thermostat |
| Парткод: | D019 4080 |
| Деталь: | Seal:Fusing Cover |
| Парткод: | D019 4169 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 0804 6123 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Screw - M3x12 |
| Парткод: | 0954 3012N |
| Деталь: | Relay Connector - 3P |
| Парткод: | 1102 6260 |
| Деталь: | Bushing:4x8 |
| Парткод: | 0733 0408 |
| Деталь: | Front Bushing - Transfer Roller |
| Парткод: | AA08 0256 |
| Деталь: | Compression Spring:Pressure:Front |
| Парткод: | B091 3911 |
| Деталь: | Front Discharge Sheet |
| Парткод: | AA15 0708 |
| Деталь: | CLEANER:REGISTRATION:DRIVEN |
| Парткод: | D019 3812 |
| Деталь: | Cover - ID Sensor |
| Парткод: | A267 3905 |
| Деталь: | Rear Bushing - Transfer Roller |
| Парткод: | AA08 0250 |
| Деталь: | Compression Spring:Pressure:Rear |
| Парткод: | B091 3912 |
| Деталь: | Terminal - Transfer Roller |
| Парткод: | A267 3861 |
| Деталь: | Terminal - Separation |
| Парткод: | A267 3862 |
| Деталь: | Cover:Transfer/Separation Unit:C5 |
| Парткод: | D019 3855 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Band - Vertical Transport Cover |
| Парткод: | D019 3941 |
| Деталь: | Lever:Shutter |
| Парткод: | D019 3931 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | D019 3859 |
| Деталь: | Pressure Cover - Transfer Unit |
| Парткод: | D019 3866 |
| Деталь: | Roller - Transfer Unit |
| Парткод: | D019 3867 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | ID SENSOR |
| Парткод: | D019 3901 |
| Деталь: | Interface Harness - Density Sensor |
| Парткод: | D019 5236 |
| Деталь: | Cover - Density Sensor Harness |
| Парткод: | D019 3908 |
| Деталь: | Guide Plate - Upper |
| Парткод: | D019 2656 |
| Деталь: | Guide Plate - Lower |
| Парткод: | D019 2775 |
| Деталь: | Separation Unit:Assy |
| Парткод: | B209 3831 |
| Деталь: | Rear Discharge Sheet |
| Парткод: | AA15 0709 |
| Деталь: | Cover Assy - Transfer/Separation |
| Парткод: | D019 3821 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | DC Motor:Paper Feed:Assy |
| Парткод: | D331 2680 |
| Деталь: | O/O (200911PCIL) |
| Парткод: | AX04 0220 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Bushing - 8x16x7 |
| Парткод: | AA08 2070 |
| Деталь: | Bracket:Rise:2 |
| Парткод: | B090 2773 |
| Деталь: | Cover:Right Inner Rear |
| Парткод: | B090 2592 |
| Деталь: | Rising Unit |
| Парткод: | D010 2780 |
| Деталь: | Pressure Lever Stopper |
| Парткод: | B024 2765 |
| Деталь: | Tension Spring:Stopper:Return |
| Парткод: | B091 2766 |
| Деталь: | Bracket:Rise:1 |
| Парткод: | B090 2815 |
| Деталь: | Vibrating Plate |
| Парткод: | A267 2770 |
| Деталь: | Lever - Paper Volume Sensor |
| Парткод: | D010 2777 |
| Деталь: | Torsion Spring:Joint:Return |
| Парткод: | B091 2767 |
| Деталь: | Stopper:Holder:Compression Spring |
| Парткод: | B090 2848 |
| Деталь: | Holder - Spring |
| Парткод: | A267 2846 |
| Деталь: | Compression Spring:Return |
| Парткод: | B091 2844 |
| Деталь: | Bushing - DC Motor Shaft |
| Парткод: | A267 2845 |
| Деталь: | Bracket:DC Motor:2 |
| Парткод: | B090 2838 |
| Деталь: | Shaft:DC Motor:Assy |
| Парткод: | D019 2860 |
| Деталь: | Lever:DC Motor:Assy |
| Парткод: | D019 2776 |
| Деталь: | Clip:Shaft |
| Парткод: | B031 2836 |
| Деталь: | TENSION SPRING |
| Парткод: | D010 2771 |
| Деталь: | Shutter - Photointerruptor |
| Парткод: | D019 2849 |
| Деталь: | Bushing - Motor Shaft |
| Парткод: | A267 2847 |
| Деталь: | Bracket:DC Motor:1 |
| Парткод: | B090 2837 |
| Деталь: | Harness Cover - Paper Feed |
| Парткод: | B024 2839 |
| Деталь: | Side Fence Bracket |
| Парткод: | D019 2795 |
| Деталь: | Cover:Positioning Pin:Middle |
| Парткод: | D019 2593 |
| Деталь: | Cover:Left Inner Rear |
| Парткод: | B090 2593 |
| Деталь: | Bracket - Paper Size Sensor |
| Парткод: | D010 2871 |
| Деталь: | Photointerruptor:Vertical Transport |
| Парткод: | AW02 0173 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Philips Truss Screw - M4x8 |
| Парткод: | 0950 4008Z |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Tapping Screw:3x30 |
| Парткод: | 0451 3030N |
| Деталь: | CLAMP |
| Парткод: | 1105 0460 |
| Деталь: | Clamp - ES-0510 |
| Парткод: | 1105 0329 |
| Деталь: | 1st Paper Tray Assy |
| Парткод: | D019 2538 |
| Деталь: | 2nd Paper Tray Assy |
| Парткод: | D019 2539 |
| Деталь: | Font Slider - Upper |
| Парткод: | D010 2867 |
| Деталь: | Front Slider - Base |
| Парткод: | D010 2873 |
| Деталь: | Front Side Fence |
| Парткод: | D010 2884 |
| Деталь: | END FENCE |
| Парткод: | D010 2853 |
| Деталь: | End Fence Seal |
| Парткод: | D010 2900 |
| Деталь: | Decal - Side Fence |
| Парткод: | B027 7352 |
| Деталь: | Rear Side Fence |
| Парткод: | D010 2885 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | D010 2861 |
| Деталь: | Spacer:Link |
| Парткод: | D010 2550 |
| Деталь: | Bracket:Rise |
| Парткод: | B090 2856 |
| Деталь: | Spring Plate - Grounding |
| Парткод: | A267 2878 |
| Деталь: | Sponge - Paper Feed Tray |
| Парткод: | A267 2899 |
| Деталь: | Roller:Paper Tray |
| Парткод: | B090 2987 |
| Деталь: | Gear - 16Z |
| Парткод: | B090 2869 |
| Деталь: | Shaft - Tray Bottom Plate |
| Парткод: | D010 2854 |
| Деталь: | PAPER TRAY |
| Парткод: | D010 2850 |
| Деталь: | Friction pad |
| Парткод: | D010 2822 |
| Деталь: | Pressure Spring - Friction Pad |
| Парткод: | A267 2834 |
| Деталь: | Sheet:Holder:Paper Tray |
| Парткод: | B091 2898 |
| Деталь: | Link - Paper Size Sensor |
| Парткод: | D010 2870 |
| Деталь: | Tension Spring - Paper Tray |
| Парткод: | D010 2956 |
| Деталь: | BASE PAD |
| Парткод: | A267 2917 |
| Деталь: | Releaselever - Paper Tray |
| Парткод: | D010 2864 |
| Деталь: | Release Shaft - Paper Tray |
| Парткод: | D010 2951 |
| Деталь: | Grip Holder - Paper Tray |
| Парткод: | D010 2955 |
| Деталь: | Release Lever - Paper Tray |
| Парткод: | D010 2953 |
| Деталь: | SPRING |
| Парткод: | AA06 0900 |
| Деталь: | Paper Tray Grip |
| Парткод: | D010 2954 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | D019 2892 |
| Деталь: | Spring Plate - Slider |
| Парткод: | D010 2875 |
| Деталь: | PAPER TRAY COVER |
| Парткод: | D010 2958 |
| Деталь: | Lever:Stopper:Front |
| Парткод: | B090 2858 |
| Деталь: | Stopper:Positioning |
| Парткод: | B090 2859 |
| Деталь: | Lever:Stopper:Positioning |
| Парткод: | B090 2860 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | G697 2677 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Side Fence Seal |
| Парткод: | D010 2897 |
| Деталь: | Rearslider - Upper |
| Парткод: | D010 2866 |
| Деталь: | Rear Slider - Base |
| Парткод: | D010 2874 |
| Деталь: | Roller:Bracket:Rise |
| Парткод: | B090 2864 |
| Деталь: | Shaft - Roller |
| Парткод: | A267 2865 |
| Деталь: | Pad:Side Fence:5mm |
| Парткод: | D010 2901 |
| Деталь: | Pad:Side Fence:8mm |
| Парткод: | D010 2902 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0450 4008N |
| Деталь: | Retaining Ring - M8 |
| Парткод: | 0720 0080E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Screw-m4x6 |
| Парткод: | 0354 0060N |
| Деталь: | Tapping Screw:M3x20 |
| Парткод: | 0450 3020N |
| Деталь: | Clamp:Card Spacer(F2) |
| Парткод: | 1105 0415 |
| Деталь: | Operation Panel - NA |
| Парткод: | D019 1411 |
| Деталь: | Operation Panel - EU |
| Парткод: | D019 1412 |
| Деталь: | Operation Panel - TWN/AA |
| Парткод: | D019 1413 |
| Деталь: | Spacer - Keytop |
| Парткод: | B238 1547 |
| Деталь: | Keytop - Counter |
| Парткод: | B238 1511 |
| Деталь: | Keytop - Blank FB |
| Парткод: | B223 1518 |
| Деталь: | Keytop - Copy NA |
| Парткод: | B223 1528 |
| Деталь: | Keytop - Doc NA |
| Парткод: | B223 1529 |
| Деталь: | Keytop:Printer:NA |
| Парткод: | B223 1531 |
| Деталь: | Keytop:Scanner:NA |
| Парткод: | B223 1532 |
| Деталь: | Keytop:Function:NA (D084/D085) |
| Парткод: | B223 1533 |
| Деталь: | Keytop:Copy:EU |
| Парткод: | B223 1534 |
| Деталь: | Keytop:Doc:EU |
| Парткод: | B223 1535 |
| Деталь: | Keytop:Printer:EU |
| Парткод: | B223 1537 |
| Деталь: | Keytop:Scanner:EU |
| Парткод: | B223 1538 |
| Деталь: | Keytop:Function:EU (D084/D085) |
| Парткод: | B223 1539 |
| Деталь: | PCB:APC1:OP-L:Sub-assy |
| Парткод: | B223 1497 |
| Деталь: | Harness:OP-R:10 |
| Парткод: | D009 1480 |
| Деталь: | Harness:OP-R:13 |
| Парткод: | D009 1481 |
| Деталь: | Bracket - LCDC Board |
| Парткод: | D019 1505 |
| Деталь: | Sheet:Data:Display:NA |
| Парткод: | B238 1540 |
| Деталь: | LCDC Board - NA |
| Парткод: | D019 1461 |
| Деталь: | LCDC Board - EU |
| Парткод: | D019 1462 |
| Деталь: | LCDC Board - TWN/AA |
| Парткод: | D019 1463 |
| Деталь: | Invertor:TFT |
| Парткод: | D009 1486 |
| Деталь: | Harness:Invertor |
| Парткод: | D009 1484 |
| Деталь: | Lower Cover - Operation Panel |
| Парткод: | D019 1502 |
| Деталь: | Lens - Front |
| Парткод: | B238 1519 |
| Деталь: | Shadeing Plate:Touch Panel |
| Парткод: | D009 1504 |
| Деталь: | Touch Panel:W-VGA:MA |
| Парткод: | D009 1488 |
| Деталь: | LCD Spacer A |
| Парткод: | B238 1534 |
| Деталь: | LCD Spacer B |
| Парткод: | B238 1535 |
| Деталь: | LCD:TFT:W-VGA:MV |
| Парткод: | D009 1498 |
| Деталь: | Cable:FFC:TFT:LCD |
| Парткод: | D009 1487 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B223 1520 |
| Деталь: | Keytop:10key:NA |
| Парткод: | B223 1540 |
| Деталь: | Keytop:10key |
| Парткод: | B223 1521 |
| Деталь: | Keytop - 10key AA |
| Парткод: | B223 1541 |
| Деталь: | Keytop - Clear Modes |
| Парткод: | B238 1583 |
| Деталь: | Keytop - Start |
| Парткод: | B238 1504 |
| Деталь: | Keytop - Try Print |
| Парткод: | B238 1506 |
| Деталь: | Keytop - Interrupt |
| Парткод: | B238 1509 |
| Деталь: | Keytop - Kantan |
| Парткод: | B238 1552 |
| Деталь: | Keytop - Login |
| Парткод: | B238 1550 |
| Деталь: | Keytop - Power Source |
| Парткод: | B238 1549 |
| Деталь: | Harness:OP-L:13 |
| Парткод: | D009 1483 |
| Деталь: | Harness:OP-L:12 |
| Парткод: | D009 1482 |
| Деталь: | PCB:ALC1:OP-R:Sub-assy |
| Парткод: | D009 1466 |
| Деталь: | Cushion Operation Sub Unit:Front Added MB18 |
| Парткод: | D019 1522 |
| Деталь: | Seal Operation Sub Unit:A Added MB18 |
| Парткод: | D019 1520 |
| Деталь: | Seal Operation Sub Unit:B Added MB18 |
| Парткод: | D019 1521 |
| Деталь: | Cover:Upper ADD (200908 PCIL) |
| Парткод: | D009 1501 |
| Деталь: | Cover:Upper:NA ADD (200908 PCIL) |
| Парткод: | D009 1551 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Ferrite Core:E04FG210810 |
| Парткод: | 1607 2053 |
| Деталь: | CLAMP |
| Парткод: | 1105 0032 |
| Деталь: | 2nd Scanner Assy (MS model) |
| Парткод: | D019 1689 |
| Деталь: | 2nd Scanner Assy (CS model) |
| Парткод: | B238 1689 |
| Деталь: | Mirror No.2 |
| Парткод: | AC03 0162 |
| Деталь: | Spring Plate - 2nd Mirror |
| Парткод: | G404 2810 |
| Деталь: | Pulley Holder |
| Парткод: | G570 2833 |
| Деталь: | Pulley - High Voltage Supply Cord |
| Парткод: | G570 2834 |
| Деталь: | Guide - High Voltage Supply Cord |
| Парткод: | G570 2832 |
| Деталь: | Idler pulley |
| Парткод: | B238 1806 |
| Деталь: | Harness - Scanner Motor |
| Парткод: | D019 5249 |
| Деталь: | Harness - STM |
| Парткод: | B238 5371 |
| Деталь: | Stepper Motor DC3.9V |
| Парткод: | B238 1715 |
| Деталь: | Bracket - Scanner Drive Motor |
| Парткод: | D019 1788 |
| Деталь: | Stepper Motor Bracket |
| Парткод: | B238 1788 |
| Деталь: | Tension Spring:Tension:14720mn |
| Парткод: | AA06 0979 |
| Деталь: | Ground Plate - Stepper Motor |
| Парткод: | B238 1762 |
| Деталь: | Timing Belt - 157ST1.5-4.0 |
| Парткод: | B238 1792 |
| Деталь: | Drive Were |
| Парткод: | B238 1787 |
| Деталь: | Bracket:Tension (MS model) |
| Парткод: | B180 1704 |
| Деталь: | Bracket:Tension (CS model) |
| Парткод: | D019 1704 |
| Деталь: | Tension Spring:Tension:11300mn |
| Парткод: | AA06 0980 |
| Деталь: | Scanner Drive Shaft |
| Парткод: | B238 1786 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2144 |
| Деталь: | Pulley:Drive Were:Rear:Sub-assy |
| Парткод: | B238 1814 |
| Деталь: | Timing Pulley 73 |
| Парткод: | G570 1133 |
| Деталь: | Pulley:Drive Were:Front:Sub-assy |
| Парткод: | B238 1816 |
| Деталь: | Heater:Scanner:NA:Assy |
| Парткод: | D019 8464 |
| Деталь: | Heater:Scanner:EU:Assy |
| Парткод: | D019 8466 |
| Деталь: | x/o MB1 |
| Парткод: | B229 1688 |
| Деталь: | 1st Slide Rail |
| Парткод: | A193 1816 |
| Деталь: | Slide Rail:No.2 |
| Парткод: | B180 1734 |
| Деталь: | Bushing Spacer |
| Парткод: | B238 1793 |
| Деталь: | Hall Plug |
| Парткод: | B238 1796 |
| Деталь: | PULLEY |
| Парткод: | B238 1807 |
| Деталь: | Main Switch Decal - NA |
| Парткод: | D010 7450 |
| Деталь: | Main Switch Decal - EU |
| Парткод: | D010 7451 |
| Деталь: | Carriage Unit No.2 |
| Парткод: | B238 1688 |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0802 5299 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0805 0088 |
| Деталь: | CLAMP |
| Парткод: | 1105 0516 |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0487 |
| Деталь: | Clamp - SB-2712 |
| Парткод: | 1105 0621 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
Коды ошибок
101-1
101-2
120
121
141
142
143
144-1
144-2
144-3
144-4
161
165
202
203
204
220
230
231
240
302
350
351
353
354
355
389
390
391
392
398
399
401
402
411
490
500
501
502
503
504
506
508
509
510
541
542
543
544
545
547
551
552
553
554
555
557
559
590
620
621
632
633
634
635
636
641
650
651
669
670
672
687
721
722
723
725
730
740
742
746
750
751
760
761
763
764
765
766
791
792
816
819
839
851
853
854
855
856
857
858
859
860
861
863
864
865
866
867
868
870
872
873
874
875
876
877
878
880
900
901
920
921
925
990
991
992
997
998
Описание
| Error code: | 101-1 |
| Description: | Exposure lamp error 1 The standard white level could not be set properly when scanning the white plate during automatic white level adjustment. |
| Causes: | • White plate dirty • Spurious electrical noise on power supply line • Exposure lamp connection loose, broken, defective • Exposure lamp defective • Lamp stabilizer connection, loose, broken, defective • Lamp stabilizer defective • High voltage power supply harness loose, broken, defective • SBU defective • BCU defective • SIO defective |
| Error code: | 101-2 |
| Description: | Exposure lamp error 1 The standard white level setting dropped below the specified range during scanning. |
| Causes: | • White plate dirty • Spurious electrical noise on power supply line • Exposure lamp connection loose, broken, defective • Exposure lamp defective • Lamp stabilizer connection, loose, broken, defective • Lamp stabilizer defective • High voltage power supply harness loose, broken, defective • SBU defective • BCU defective • SIO defective |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 141 |
| Display: | SVC 141 ERROR |
| Description: | Motor |
| Causes: | • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor excessive PWM - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board” |
| Error code: | 142 |
| Display: | Contact the Service center. 142: Error |
| Description: | Motor |
| Causes: | • Standard white plate defective, dirty • Moisture inside the scanner unit • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor, over speed - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”. |
| Error code: | 143 |
| Display: | Service Call 143:Error |
| Description: | Motor |
| Causes: | • SBU defective • IPU defective • BCU defective • Harness between the SBU and IPU defective • Harness between the BCU-IPU defective • Standard white plate not installed correctly, or is dirty • Scanner mirrors and/or lenses are dirty or installed incorrectly |
| Remedy: | DC pick motor, no encoder feedback - staging motor - replace the “Staging motor” on page 4-79. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 144-1 |
| Description: | SBU connection error Connection to the SBU could not be confirmed, possibly due to a defect in the BCU detection board |
| Causes: | • Harness connection at IPU, BCU, SBU loose, broken, defective. • Spurious electrical noise on power supply line • IPU defective • BCU defective • SBU defective |
| Error code: | 144-2 |
| Description: | SBU serial communication error Poor SBU power supply caused by SIO, or BCU detection board defective. |
| Causes: | • Harness connection at IPU, BCU, SBU loose, broken, defective. • Spurious electrical noise on power supply line • IPU defective • BCU defective • SBU defective |
| Error code: | 144-3 |
| Description: | SBU GASBU reset error SBU defective, BCU detection circuit defective. |
| Causes: | • Harness connection at IPU, BCU, SBU loose, broken, defective. • Spurious electrical noise on power supply line • IPU defective • BCU defective • SBU defective |
| Error code: | 144-4 |
| Description: | SBU version error SBU defective, BCU detection circuit defective. |
| Causes: | • Harness connection at IPU, BCU, SBU loose, broken, defective. • Spurious electrical noise on power supply line • IPU defective • BCU defective • SBU defective |
| Error code: | 161 |
| Display: | SYSTEM HALT (*) 161 : PCB MAIN-F6 |
| Description: | IPU Error At power on, or when the machine returns from an energy save mode, the self-diagnostic program returned an IPU error. |
| Causes: | • IPU defective • Connection between SBU and IPU is loose, broken, or defective |
| Error code: | 165 |
| Description: | Out of Paper; Load Tray 1 (MPT) with [size] [type] The Tray 1 (MPT) No Paper Sensor indicates Tray 1 (MPT) is empty. |
| Causes: | • No Paper Sensor, PL5.3.14 • No Paper Sensor Actuator, PL5.3.15 • FRONT/DUP Harness, PL5.3.28 |
| Remedy: | 1 Fill Tray 1 (MPT) with paper. Does the error persist? Go to Step 2. Complete. 2 Check the following for evidence of fault or damage: • Tray 1 (MPT) No Paper Sensor, PL5.3.14 • Sensor Actuator, PL5.3.15 Is there any damage? Replace any damaged parts. Go to Step 3. 3 Test the Tray 1 (MPT) No Paper Sensor. Run the Service Diagnostics Tray 1 (MPT) No Paper Sensor test. Does the sensor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the Tray 1 (MPT) No Paper Sensor signal. Is there +3.3 V across P/J135-1 <=> P/J135-2? Replace the sensor. Go to Step 5. 5 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J135. 2. Check continuity between J13 <=> J134. Replace the Engine Control Board. Replace the FRONT/DUP Harness. |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 204 |
| Display: | Power OFF/ON 204:Error |
| Description: | Polygon motor error 3: XSCRDY signal error |
| Causes: | The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing. |
| Remedy: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board). |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 231 |
| Display: | Service Call 231: Error |
| Description: | FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 240 |
| Display: | Service call 240: Error |
| Description: | LD error |
| Causes: | The IPU (EGB) detects a problem at the LD unit. |
| Remedy: | • Worn-out LD • Disconnected or broken harness of the LD. 1. Replace the laser optics unit. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 350 |
| Description: | ID sensor error 1 One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. Vsp greater than or equals 2.5V Vsg less than 2.5 Vsp = 0V Vsg = 0 |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 351 |
| Description: | ID sensor error 2 The ID sensor output voltage is 5.0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 353 |
| Description: | ID sensor error 4 One of the following ID sensor output voltages is detected at ID sensor initialization. Vsg less than 4.0V when the maximum PWM input (255) is applied to the ID sensor. Vsg greater than or equal to 4.0V when the minimum PWM input (0) is applied to the ID sensor. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 354 |
| Display: | Set new fuser 354: Fuser life |
| Description: | Fuser life (occurs when fuser life continuation is OFF). |
| Causes: | Right after replacing fuser? |
| Remedy: | Check fuser life. Replace fuser. |
| Error code: | 355 |
| Display: | Set new belt 355: Belt life |
| Description: | Belt life notified (alarm). Print N-count by opening and closing cover. |
| Causes: | Right after replacing belt? |
| Remedy: | Check belt life. Replace belt. |
| Error code: | 389 |
| Display: | Open top cover 389: Paper jam |
| Description: | Jam generated in paper path. |
| Causes: | Open front cover and check jammed paper. |
| Remedy: | Remove jammed paper. |
| Error code: | 390 |
| Display: | Check MP tray 390: Paper jam |
| Description: | Paper jam during paper feed from MT. |
| Causes: | Check for miss-fed paper around MT cassette. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace MT. |
| Error code: | 391 |
| Description: | TD sensor error: Auto adjust error During automatic adjustment of the TD sensor, output voltage was less than 1.8V, or more than 4.8V during TD sensor initial setting |
| Causes: | • TD sensor connector or harness loose, broken, defective • TD sensor defective • IOB defective • Toner supply defective (confirm that the toner seal strip has been removed from toner cartridge) |
| Remedy: | 1. Check the harness or harness connection. 2. Clean the surface of the quenching lamp glass. |
| Error code: | 392 |
| Description: | Development Bias Error The development bias feedback voltage was less than 0.3 V for longer than 200 ms while the PWM duty value was more than 5% (indicating a development bias leak). |
| Causes: | • Bias terminal damaged • High voltage cable damaged, defective • CGB power pack defective |
| Error code: | 398 |
| Description: | Drum/Development motor error: C The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on. |
| Causes: | • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system |
| Remedy: | 1. Check or replace the harness. 2. Replace the drum/development motor. 3. Replace the 24V fuse on the PSU. |
| Error code: | 399 |
| Description: | Drum/Development motor error: Y The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on. |
| Causes: | • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system |
| Remedy: | 1. Check or replace the harness. 2. Replace the drum/development motor. 3. Replace the 24V fuse on the PSU. |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 411 |
| Display: | SVC 411 ERROR |
| Description: | IRQ timer 1 error |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | Replace the Controller board. |
| Error code: | 490 |
| Display: | Set 490: No paper in MP tray (* stands for A4 B4, etc.) |
| Description: | ITB (Image Transfer Belt) Unit Set Error |
| Causes: | The TM sensor does not detect the reflection from the ITB. |
| Remedy: | • No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S |
| Error code: | 500 |
| Description: | Transport/Fusing Motor Error |
| Causes: | The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the transport/fusing motor. Replace it if necessary. |
| Error code: | 501 |
| Display: | Service Call 501: Error |
| Description: | Tray 1 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503 |
| Display: | Service Call 503: Error |
| Description: | Tray 3 must be rebuilt |
| Causes: | (A model other than D581) Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. (D581) Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 504 |
| Description: | Tray 4 must be rebuilt |
| Causes: | The 2nd tray of D580, 1st tray of D580 when D579 and D580 are attached, the bottom D579 when two units of D579 are attached, or D631 when D581 and D631 are attached. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection D581 when D579 and D581 are attached.Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 506 |
| Display: | SYSTEM HALT (*) 506 : STATION SENS |
| Description: | Bypass must be rebuilt |
| Causes: | • Paper tray unit main motor connector or harness loose, broken, defective • Motor overload due to an obstruction • Motor defective |
| Remedy: | 1. Replace the tray 3 or 4 lift motor. 2. Replace the tray 3 or 4 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3 or 4. |
| Error code: | 508 |
| Description: | Replace black developer |
| Causes: | • HP sensors on the left and right side loose, disconnected, defective • Cutter motor harness damaged, defective • HP sensors defective • Cutter motor defective Note: Paper can be fed from the bypass table if the roll feeder or paper cassette is not operationg. |
| Error code: | 509 |
| Display: | SYSTEM HALT (*) 509 : HDC POSCNT |
| Description: | Replace red developer |
| Causes: | • Poor connection or defective tray 5 or 6 lift motor • Poor connection or defective tray 5 or 6 lift sensor • Remaining paper or another obstruction has stopped the tray and motor. • Pick-up solenoid 5 or 6 connector is loose. • Pick-up solenoid 5 or 6 is blocked by an obstruction. |
| Remedy: | 1. Replace the tray 5 or 6 lift motor. 2. Replace the tray 5 or 6 lift sensor. 3. Check or clear obstacles around pick-up solenoid 5 or 6. |
| Error code: | 510 |
| Display: | SYSTEM HALT (*) 510 : X ORGIN |
| Description: | Replace green developer |
| Causes: | • Tray lift motor defective or connector disconnected • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Remedy: | 1. Check the harness connection or replace it. 2. Replace the bypass tray lift motor. 3. Replace the bypass upper limit sensor. 4. Replace the bypass lower limit sensor. 5. Check or clear obstacles around the bypass pick-up solenoid. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 554 |
| Description: | Fusing sleeve belt overheat: End (hardware error) The fusing sleeve belt thermistor detects 250°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 555 |
| Description: | Fusing Heater error: End The fusing heater keeps full power for 9 seconds or more. |
| Causes: | Defective thermistors. Broken heater cables. |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 590 |
| Description: | Toner collection motor error The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on. |
| Causes: | • Motor lock due to obstruction • Motor driver board defective • Motor connection loose, defective • Toner collection motor sensor disconnected, sensor defective • Rotational transmission shaft (o6 x 30) missing |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 633 |
| Description: | Key/card counter device error 2 During communication with the device, the MCU received a break (Low) signal. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 636 |
| Description: | OSM User Code File Error The correct "usercode" file could not be found in the root folder of the SD card because the file is not present, or the existing file is corrupted or the wrong type file. |
| Causes: | • Make sure the eccm.mod file is in the root folder of the SD card. Note: The usercode files are created with the User Setting Tool "IDissuer.exe". |
| Error code: | 641 |
| Description: | BICU control data transfer abnormal A sampling of the control data sent from the BICU reveals an abnormality. |
| Causes: | • Defective controller board • External noise • Defective BCU |
| Remedy: | 1. Replace the controller board. 2. Replace the BCU. |
| Error code: | 650 |
| Description: | @Remote communication error 1 A dial-up or modem error occurred during @Remote operation. (This error occurs only during @Remote operation.) |
| Causes: | • Modem line disconnected • Modem board missing or not properly installed |
| Error code: | 651 |
| Description: | @Remote communication error 2 An illegal dial-up to the service center was attempted by @Remote. |
| Causes: | • Software bug |
| Error code: | 669 |
| Description: | EEPROM Error |
| Causes: | An unexpected value exists in the initialization flag of the EEPROM |
| Remedy: | • EEPROM not initialized • Defective EEPROM |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 721 |
| Description: | Jogger motor error • Jogger HP sensor does not detect the jogger fence for 2000ms after the jogger unit has moved to its home position. • Jogger HP sensor does not turn off 300 ms after the jogger unit has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective jogger HP sensor • Overload on the jogger motor • Defective jogger motor • Defective main board • Disconnected or defective harness |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the jogger HP sensor (if the jogger motor works correctly). 3. Replace the jogger motor (if the jogger motor does not work). 4. Replace the finisher main board. |
| Error code: | 722 |
| Description: | Finisher jogger motor error The finisher jogger HP sensor did not return to the home position, or move out of the home position, within 1.25 sec. Staple mode cannot be used. |
| Causes: | • Jogger motor connector or harness loose, broken, defective • Jogger motor defective • Jogger HP sensor connector or harness loose, broken, defective • Jogger HP sensor defective |
| Error code: | 723 |
| Description: | Stack feed-out motor error • Stack feed-out HP sensor does not detect the home position of the stack feedout belt 3000ms after the stack feed-out belt has moved to its home position. • Stack feed-out HP sensor does not turn off 200 ms after the stack feed-out belt has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code |
| Causes: | • Defective stack feed-out HP sensor • Overload on the stack feed-out motor • Defective stack feed-out motor • Defective main board • Disconnected or defective harness |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the stack feed-out HP sensor (if the stack feed-out motor works correctly). 3. Replace the stack feed-out motor (if the stack feed-out motor does not work). 4. Replace the finisher main board. |
| Error code: | 725 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor. 4. Replace the finisher main board. |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 740 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished after a certain time. For the 1000-sheet booklet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 742 |
| Description: | Finisher stapler movement motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished for a certain time. For the 1000-sheet booklet finisher • The stapler HP sensor is not activated within the specified time after the stapler motor turned on. (first detection: jam error, consecutive twice detection SC code). |
| Causes: | • Motor overload • Loose connection of the stapler home position sensor • Loose connection of the stapler movement motor • Defective stapler home position sensor • Defective stapler movement motor |
| Remedy: | 1. Check the connection of the stapler movement motor. 2. Check the connection of the stapler home position sensor. 3. Replace the stapler home position sensor. 4. Replace the stapler movement motor. |
| Error code: | 746 |
| Description: | 1000-sheet booklet finisher: Stack feed motor error • The stack feed HP sensor does not detect "ON" twice (once: jam error) for specified time after the stack feed motor has turned on. • The stack feed HP sensor does not detect "OFF" twice (once: jam error) for specified time after the stack feed motor has turned on. |
| Causes: | • Motor overload • Loose connection of the stack feed motor • Defective stack feed motor |
| Remedy: | 1. Check the connections and cables for the stack feed motor and HP sensor. 2. Check for blockages in the stack feed motor mechanism. 3. Replace the stack feed HP sensor and/or stack feed motor 4. Replace the finisher main board. |
| Error code: | 750 |
| Description: | 1000/3000-sheet (booklet) finisher: Tray lift motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. |
| Causes: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor |
| Remedy: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor. |
| Error code: | 751 |
| Description: | Stack pressure solenoid error The stack pressure solenoid in the finisher is not operating. |
| Causes: | • Solenoid harness loose, broken • Solenoid obstructed • Stack height sensor dirty, harness loose, broke • Solenoid defective • Stack height sensor defective |
| Error code: | 760 |
| Description: | Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Punch HP sensor disconnected, defective • Punch motor disconnected or defective • Punch motor overload due to obstruction |
| Remedy: | 1. Check the connections and cables for the punch motor and HP sensor. 2. Check for blockages in the punch motor mechanism. 3. Replace the punch HP sensor and/or punch motor 4. Replace the finisher main board. |
| Error code: | 761 |
| Description: | Finisher folder plate motor error The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Remedy: | 1. Check the connections and cables for the folder plate motor and HP sensor. 2. Check for blockages in the folder plate motor mechanism. 3. Replace the folder plate HP sensor and/or folder plate motor 4. Replace the finisher main board. |
| Error code: | 763 |
| Description: | Rear fold plate HP sensor error The state (on/off, off/on) of the rear fold plate HP sensor in the fan fold unit did not change 1 sec. after the plate started to move. |
| Causes: | • Fold plate motor (R) harness connector loose, disconnected, broken • Rear fold plate HP sensor harness connector loose, disconnected, broken • Fold plate motor (R) defective • Rear fold plate HP sensor defective • Undetected paper is jamming the action of the motor or fold plate • Fan folder unit MCU defective |
| Error code: | 764 |
| Description: | Paper position sensor slide motor error The paper position sensor moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the paper position sensor slide motor. 2. Replace the paper position sensor slide motor. |
| Error code: | 765 |
| Description: | Fold unit bottom fence motor error The bottom fence of the fold unit moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the fold unit bottom fence motor. 2. Defective fold unit bottom fence motor. |
| Error code: | 766 |
| Description: | Stacking sponge roller motor error The sponge roller moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the stacking sponge roller motor. 2. Defective stacking sponge roller motor. |
| Error code: | 791 |
| Description: | Bridge unit error The machine recognizes the finisher, but does not recognize the bridge unit. |
| Causes: | The bridge unit is not installed. Defective bridge unit. Re-install the bridge unit. Turn the main power switch off and on. |
| Remedy: | • Re-install the bridge unit. • Turn the main power switch off and on. |
| Error code: | 792 |
| Description: | Finisher error The machine does not recognize the finisher, but recognizes the bridge unit. |
| Causes: | The finisher`s connection is faulty. The finisher is not attached to a device equipped with the bridge unit. Defective finisher. |
| Remedy: | Reconnect the finisher or bridge unit, and then turn the main power switch off and then back on. |
| Error code: | 816 |
| Display: | SYSTEM HALT (*) 816 : FW/FROM WRC |
| Description: | Energy saving I/O sub-system error |
| Causes: | The energy saving I/O sub-system detects an error. • Defective energy saving I/O sub-system • The energy saving I/O sub-system detects a controller board error (No response) |
| Remedy: | • Turn the main power switch off and on. • Replace the controller board. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 839 |
| Display: | SYSTEM HALT (*) 839 : FW/PRN MDL |
| Description: | Serial Flash A read/write operation on the Software Status Register failed. |
| Causes: | • Replace the controller board |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 858 |
| Description: | Data encryption conversion error (1) |
| Causes: | -01 A serious error has occurred during the data conversion performed for updating the key for data encryption. • The data in the USB flash drive is damaged. • A communication error has occurred due to electromagnetic waves or other noise. • Replace the controller board. * However, if it is "-30", the machine may recover by turning the main power switch off and then back on. -02 A Data encryption conversion error (2) A serious error occurs when data is encrypted to update an encryption key. Defective NVRAM Replace the controller board. -30 A Data encryption conversion error (3) A recoverable error has occurred before starting data conversion. Defective NVRAM • Turn the main switch off and on. • If the error reoccurs, replace the controller board. -31 A A serious error occurs while the data is encrypted. Same as SC991 Same as SC991 |
| Error code: | 859 |
| Description: | HDD data encryption error |
| Causes: | -01 B HDD check error • Hard disk data conversion has been selected, but the hard disk is not installed. • The hard disk is not mounted properly. • No HDD installed • Hard disk formatting is not completed. • The encryption key on the board and the actual encryption key in the hard disk do not match. • Install the HDD correctly. • Initialize the HDD with SP5-832-001. -02 B Power failure during data encryption. The data conversion in the NVRAM or hard disk has not completed successfully. Power interruption has occurred during the conversion of the data in the NVRAM or hard disk Initialize the HDD with SP5-832-001. -10 B Data Read/Write command error Due to time-out, serial communication error, or other problems in DMAC, an irregular DMAC return value has occurred consecutively two or more times Noise or other problems in the SATA connection Same as SC863 |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 877 |
| Description: | HDD Data Erase Error The Data Overwrite Security option cannot scramble and erase data on the HDD because the DOS SD card has been corrupted or has |
| Causes: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not been removed from the SD card slot. |
| Remedy: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not solve the problem, the SD card has been damaged.) • Install a new NVRAM • Install a new Data Overwrite Security option with a new SD card |
| Error code: | 878 |
| Description: | TPM electronic recognition error |
| Causes: | -00 The system firmware is not authenticated by TPM. The system hash value registered in the TPM at the machine`s system startup does not match that registered in the USB flash drive. • The system module was updated without going through the formal update process. • Incorrect operating of the USB flash. Replace the board. -01 D USB Flash error An error has occurred in the file system in the USB flash drive. The file system of the USB flash drive is damaged. Replace the controller board. -02 D TPM error An error has occurred in the TPM or TPM driver. Defective TPM Replace the controller board. -03 D TCSD error An error has occurred in the TPM software stack. • The TPM software stack cannot be launched. • The file required for the TPM software stack is missing. Replace the controller board. |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
