Ricoh MP2852
Рейтинг
Модули
Duplex Section 2
PAPER TRAY
OPERATION PANEL
SCANNER SECTION 3
TRANSFER UNIT
PAPER EXIT SECTION
Duplex Section 5
ELECTRICAL SECTION 1
Paper Feed Section 1
DRIVE SECTION 2
Duplex Section 1
PAPER REGISTRATION
PAPER FEED SECTION 2
TONER SUPPLY UNIT
Duplex Section 3
PCU
DRIVE SECTION 3
LD unit
Duplex Section 4
ELECTRICAL SECTION 3
Paper Invert Section
EXTERIOR 3
FUSING UNIT 2
FUSING UNIT 1
BY-PASS FEED SECTION
FRAME SECTION
Controller Section
SCANNER SECTION 2
EXTERIOR 2
Drive Section 1
ELECTRICAL SECTION 4
Scanner Section 1
EXTERIOR 1
ELECTRICAL SECTION 2
Детали SCANNER SECTION 2
| Деталь: | Transport Roller: Duplex: Connecting |
| Парткод: | AF02 0756 |
| Деталь: | Transport Roller: Duplex: Exit |
| Парткод: | AF02 0754 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | D009 4664 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | Compression Spring: Roller: Driven |
| Парткод: | AA06 3475 |
| Деталь: | Bracket: Duplex: Exit Sensor |
| Парткод: | D120 4647 |
| Деталь: | Photointerruptor: Duplex |
| Парткод: | AW02 0206 |
| Деталь: | Spring Plate: Guide Plate: Pressure |
| Парткод: | D120 4675 |
| Деталь: | Guide Plate: Driven |
| Парткод: | D120 4613 |
| Деталь: | Driven Roller: Entrance: Duplex |
| Парткод: | D039 4542 |
| Деталь: | Bushing: DIA4 |
| Парткод: | B223 4552 |
| Деталь: | Tension Spring: Driven Roller |
| Парткод: | D039 4597 |
| Деталь: | Guide Plate: Duplex: Entrance |
| Парткод: | D120 4619 |
| Деталь: | Harness: Duplex Unit: Main |
| Парткод: | D120 5352 |
| Деталь: | Arm: Pressure Release: Duplex: Rear |
| Парткод: | D120 4664 |
| Деталь: | Arm: Pressure Release: Duplex: Front |
| Парткод: | D120 4653 |
| Деталь: | Pulley: Transport Roller: Entrance |
| Парткод: | AB03 0847 |
| Деталь: | Timing Belt: S2M288 |
| Парткод: | AA04 3584 |
| Деталь: | Decal: Duplex: Open And Close |
| Парткод: | D120 4640 |
| Деталь: | Stopper: Guide Plate: Driven |
| Парткод: | D120 4614 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Bushing: DIA6: DIA10: 9 |
| Парткод: | AA08 2154 |
| Деталь: | Harness: Connecting: Duplex Unit: Sensor |
| Парткод: | D120 5351 |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x8 |
| Парткод: | 0802 5319 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0805 0089 |
| Деталь: | Paper Tray: No.1: Assy |
| Парткод: | D120 2850 |
| Деталь: | Paper Tray: No.2: Assy |
| Парткод: | D120 2900 |
| Деталь: | Tray Bottom Plate: Assy (2nd Tray) |
| Парткод: | D089 2940 |
| Деталь: | Tray Bottom Plate: No.1: Assy |
| Парткод: | D120 2940 |
| Деталь: | PAD |
| Парткод: | AF03 3010 |
| Деталь: | End Fence: Assy |
| Парткод: | D120 2832 |
| Деталь: | Side Fence: Front: Assy (1st Tray) |
| Парткод: | D120 2920 |
| Деталь: | Side Fence: Front: Assy (2nd Tray) |
| Парткод: | D120 2926 |
| Деталь: | Plate: Side Fence: Right |
| Парткод: | B223 2935 |
| Деталь: | Plate: Side Fence |
| Парткод: | B223 2934 |
| Деталь: | Lever: Stopper: Front |
| Парткод: | D120 2924 |
| Деталь: | Spring Plate: Stopper: Front |
| Парткод: | B004 2923 |
| Деталь: | Side Fence: Rear: Assy (1st Tray) |
| Парткод: | D120 2930 |
| Деталь: | Side Fence: Rear: Assy (2nd Tray) |
| Парткод: | D120 2933 |
| Деталь: | Lever: Stopper: Positioning |
| Парткод: | D120 2864 |
| Деталь: | Spring Plate: Side Fence: Positioning |
| Парткод: | A267 2857 |
| Деталь: | Stopper: Positioning |
| Парткод: | A267 2859 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | Tension Spring: Side Fence: Rear |
| Парткод: | AA06 1003 |
| Деталь: | Gear - 16Z |
| Парткод: | B223 2936 |
| Деталь: | Rise Lever |
| Парткод: | B223 2918 |
| Деталь: | Rise No.1 Shaft |
| Парткод: | B223 2865 |
| Деталь: | Ground Plate - Paper Tray No.2 |
| Парткод: | B223 2919 |
| Деталь: | Seal: Tray |
| Парткод: | B180 2782 |
| Деталь: | Link - Paper Size Sensor |
| Парткод: | B223 2910 |
| Деталь: | Lever: Release: Paper Tray: Outer |
| Парткод: | B223 2868 |
| Деталь: | Shaft: Release: Paper Tray |
| Парткод: | D029 2863 |
| Деталь: | Tension Spring: Grip |
| Парткод: | AA06 1014 |
| Деталь: | Lever: Release: Paper Tray: Inner |
| Парткод: | D120 2862 |
| Деталь: | Holder: Grip: Paper Tray |
| Парткод: | D120 2861 |
| Деталь: | Cover: Paper Tray |
| Парткод: | D120 2946 |
| Деталь: | Decal: Paper Set Direction: Tray: Left |
| Парткод: | D120 2870 |
| Деталь: | Grip: Paper Tray |
| Парткод: | D120 2860 |
| Деталь: | Decal: Paper Tray: No.1 |
| Парткод: | D120 2872 |
| Деталь: | Decal: Paper Tray: No.2 |
| Парткод: | D120 2873 |
| Деталь: | SPACER |
| Парткод: | B223 2911 |
| Деталь: | Decal: Side Fence: Rear |
| Парткод: | D120 2875 |
| Деталь: | Decal: Size Indication: Paper Tray |
| Парткод: | D120 2874 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0450 4008N |
| Деталь: | Binding Self Tapping Screw: 3x8 |
| Парткод: | 0453 3008N |
| Деталь: | Retaining Ring - M8 |
| Парткод: | 0720 0080E |
| Деталь: | Hexagon Head Tapping Screw: ES: 3x12 |
| Парткод: | 0802 5322 |
| Деталь: | Spacer - 12.7mm |
| Парткод: | 1105 0415 |
| Деталь: | Operation Sub-Unit: OVL-C1: NA: Assy |
| Парткод: | D120 1401 |
| Деталь: | Operation Sub-Unit: OVL-C1: EU: Assy |
| Парткод: | D120 1402 |
| Деталь: | Operation Sub-Unit: OVL-C1: AA: Assy |
| Парткод: | D120 1403 |
| Деталь: | Operation Sub-Unit: OVL-C1: TWN: Assy |
| Парткод: | D120 1414 |
| Деталь: | Operation Sub-Unit: OVL-C1: CHN: Assy |
| Парткод: | D120 1415 |
| Деталь: | Spacer - Keytop |
| Парткод: | B238 1547 |
| Деталь: | Keytop: Counter |
| Парткод: | D120 1514 |
| Деталь: | Keytop: Blank |
| Парткод: | D120 1521 |
| Деталь: | PCB OP-L: Service: Assy |
| Парткод: | D120 1471 |
| Деталь: | Harness: OP-L: 12 |
| Парткод: | D009 1480 |
| Деталь: | Harness: OP-R: 13 |
| Парткод: | D009 1481 |
| Деталь: | Bracket: LCDC: Assy |
| Парткод: | D120 1540 |
| Деталь: | Sheet: Logo |
| Парткод: | D120 1551 |
| Деталь: | Sheet: Logo: LAN |
| Парткод: | D120 1556 |
| Деталь: | Sheet: Logo: GES |
| Парткод: | D120 1557 |
| Деталь: | Sheet: Logo: REX |
| Парткод: | D120 1558 |
| Деталь: | Sheet: Logo: NAS |
| Парткод: | D120 1559 |
| Деталь: | Sheet: Logo: INF |
| Парткод: | D120 1560 |
| Деталь: | Sheet: Logo: SAV |
| Парткод: | D120 1561 |
| Деталь: | PCB: LCDC: NA: FT: Assy |
| Парткод: | D120 1474 |
| Деталь: | PCB: LCDC: EU: FT: Assy |
| Парткод: | D120 1475 |
| Деталь: | PCB: LCDC: TWN/AA: FT: Assy |
| Парткод: | D120 1479 |
| Деталь: | Operation Panel Bracket |
| Парткод: | B238 1527 |
| Деталь: | Operation Panel Bracket - Right |
| Парткод: | B238 1548 |
| Деталь: | Cover: Lower |
| Парткод: | D120 1501 |
| Деталь: | Lens - Front |
| Парткод: | B238 1519 |
| Деталь: | Shading Plate: Touch Panel |
| Парткод: | D120 1543 |
| Деталь: | Touch Panel: W-VGA: P |
| Парткод: | D120 1489 |
| Деталь: | LCD Spacer A |
| Парткод: | B238 1534 |
| Деталь: | LCD Spacer B |
| Парткод: | B238 1535 |
| Деталь: | LCD: TFT: W-VGA: MV: LED |
| Парткод: | D120 1498 |
| Деталь: | Cable: FFC: LCD |
| Парткод: | D120 1487 |
| Деталь: | Keytop: Clear/Stop |
| Парткод: | D120 1507 |
| Деталь: | Keytop: 10key: AA |
| Парткод: | D120 1513 |
| Деталь: | Keytop: 10key |
| Парткод: | D120 1511 |
| Деталь: | Keytop: Clear Modes |
| Парткод: | D120 1509 |
| Деталь: | Keytop: Start |
| Парткод: | D120 1506 |
| Деталь: | Keytop: Try Print |
| Парткод: | D120 1510 |
| Деталь: | Keytop - Interrupt |
| Парткод: | B238 1509 |
| Деталь: | Keytop - Kantan |
| Парткод: | B238 1552 |
| Деталь: | Keytop: Login |
| Парткод: | D120 1552 |
| Деталь: | Keytop - Power Source |
| Парткод: | B238 1549 |
| Деталь: | Harness: OP-L: 13 |
| Парткод: | D120 1483 |
| Деталь: | Harness: OP-L: 12 |
| Парткод: | D120 1482 |
| Деталь: | PCB: OP-R: Service: Assy |
| Парткод: | D120 1470 |
| Деталь: | Panel: NA |
| Парткод: | D120 1504 |
| Деталь: | Panel: EU |
| Парткод: | D120 1505 |
| Деталь: | Cover: Upper |
| Парткод: | D120 1500 |
| Деталь: | Keytop: Copy: NA |
| Парткод: | D120 1528 |
| Деталь: | Keytop: Copy: EU |
| Парткод: | D120 1534 |
| Деталь: | Keytop: DOC: NA |
| Парткод: | D120 1529 |
| Деталь: | Keytop: DOC: EU |
| Парткод: | D120 1535 |
| Деталь: | Keytop: Scanner: NA |
| Парткод: | D120 1532 |
| Деталь: | Keytop: Scanner: EU |
| Парткод: | D120 1538 |
| Деталь: | Keytop: Printer: NA |
| Парткод: | D120 1531 |
| Деталь: | Keytop: Printer: EU |
| Парткод: | D120 1537 |
| Деталь: | Keytop: Function: NA |
| Парткод: | D120 1533 |
| Деталь: | Keytop: Function: EU |
| Парткод: | D120 1539 |
| Деталь: | Sheet: Power Source: Display: NA(NA/AA) |
| Парткод: | D120 1546 |
| Деталь: | Sheet: Power Source: Display: EU(EU/TWN/CHN) 1 |
| Парткод: | D120 1547 |
| Деталь: | Sheet: Data: Display: NA(NA/AA) |
| Парткод: | D120 1549 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Ferrite Core: K3 FF 25.00x10.00x3.00x0.80(M) |
| Парткод: | 1607 2392 |
| Деталь: | CLAMP |
| Парткод: | 1105 0032 |
| Деталь: | Clamp: RBWS-0510D-V0 |
| Парткод: | 1105 0582 |
| Деталь: | Harness: Scanner: STM |
| Парткод: | D120 5218 |
| Деталь: | Stepper Motor DC3.9V |
| Парткод: | B238 1715 |
| Деталь: | Bracket: Stepper Motor: Drive |
| Парткод: | D039 1724 |
| Деталь: | Ground Plate - Stepper Motor |
| Парткод: | B238 1762 |
| Деталь: | Timing Belt - 157ST1.5-4.0 |
| Парткод: | B238 1792 |
| Деталь: | Pulley: Idler: Left Front: PeenN |
| Парткод: | D039 1718 |
| Деталь: | Pulley: Idler: Left Rear: PeenN |
| Парткод: | D039 1720 |
| Деталь: | Original Sensor - 48mm |
| Парткод: | AW01 0134 |
| Деталь: | Interface Cable: Scanner: LVDS: Hf: Assy |
| Парткод: | D120 5221 |
| Деталь: | Lens: Holder: Assy |
| Парткод: | D120 1821 |
| Деталь: | PCB: SIO |
| Парткод: | D120 5180 |
| Деталь: | Harness: Scanner: Base |
| Парткод: | D120 5215 |
| Деталь: | Harness: Scanner: BCU |
| Парткод: | D120 5217 |
| Деталь: | Timing Pulley 73 |
| Парткод: | G570 1133 |
| Деталь: | Drive Were |
| Парткод: | D039 1715 |
| Деталь: | Pulley: Drive Were: Rear: Assy |
| Парткод: | D029 1748 |
| Деталь: | Pulley: Protection |
| Парткод: | D029 1749 |
| Деталь: | Bracket: Tension: Front |
| Парткод: | D039 1712 |
| Деталь: | Tension Spring: Tension: 14720mn |
| Парткод: | AA06 0979 |
| Деталь: | Pulley: Drive Were: Front |
| Парткод: | D029 1745 |
| Деталь: | Shaft: Scanner: Drive |
| Парткод: | D039 1717 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2144 |
| Деталь: | Bracket: Tension: Rear |
| Парткод: | D039 1713 |
| Деталь: | Tension Spring: Tension: 11300mN |
| Парткод: | AA06 0980 |
| Деталь: | Bracket: Original Sensor: Sub Scanning |
| Парткод: | D039 1764 |
| Деталь: | Bracket: SIO |
| Парткод: | D120 1761 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Hexagonal Bolt: W/Washer: M3x8 |
| Парткод: | 0804 6123 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0805 0088 |
| Деталь: | Tapping Screw: Washer: 3x10 |
| Парткод: | 0802 5312 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006P |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Plain Shaft Bearing: Positioning: Transfer/Separation Unit |
| Парткод: | D120 3858 |
| Деталь: | Transfer/Separation Unit: C1: Assy |
| Парткод: | D120 3831 |
| Деталь: | Cleaner: Registration: Driven |
| Парткод: | D120 3812 |
| Деталь: | Cover: Density Sensor |
| Парткод: | D120 3905 |
| Деталь: | Front Discharge Sheet |
| Парткод: | AA15 0708 |
| Деталь: | Bushing: Transfer Roller |
| Парткод: | AA08 0349 |
| Деталь: | Compression Spring: Pressure: Transfer/Separation Unit |
| Парткод: | D120 3859 |
| Деталь: | Cover: Transfer/Separation Unit |
| Парткод: | D120 3855 |
| Деталь: | Terminal: Transfer Roller |
| Парткод: | D120 3861 |
| Деталь: | Terminal: Separation |
| Парткод: | D120 3862 |
| Деталь: | Compression Spring: Pressure: Transfer Roller: Rear |
| Парткод: | D120 3912 |
| Деталь: | Cover: Pressure: Transfer Unit |
| Парткод: | D120 3866 |
| Деталь: | Roller: Transfer Unit |
| Парткод: | D120 3867 |
| Деталь: | Cover: Harness: Density Sensor |
| Парткод: | D120 3908 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Harness: Connecting: Density Sensor |
| Парткод: | D120 5336 |
| Деталь: | DENSITY SENSOR |
| Парткод: | B259 3890 |
| Деталь: | Compression Spring: Pressure: Transfer Roller: Front |
| Парткод: | D120 3911 |
| Деталь: | Lever: Shutter |
| Парткод: | D120 3931 |
| Деталь: | Band: Stopper: Cover: Transfer/Separation Unit |
| Парткод: | D120 3941 |
| Деталь: | Rear Discharge Sheet |
| Парткод: | AA15 0709 |
| Деталь: | Bushing: Transfer Roller: Front |
| Парткод: | AA08 0350 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x8 |
| Парткод: | 0802 5319 |
| Деталь: | Bracket: DC Fan Motor: Sirocco |
| Парткод: | D120 1129 |
| Деталь: | Shaft: Exit: Exit |
| Парткод: | D120 4479 |
| Деталь: | Feeler: Exit: Exit |
| Парткод: | D120 4478 |
| Деталь: | Bracket: Duplex: Lock: Rear: Assy |
| Парткод: | D120 1099 |
| Деталь: | Discharge Brush: Exit |
| Парткод: | AA12 0146 |
| Деталь: | Roller: Tension |
| Парткод: | AF04 0059 |
| Деталь: | Spring Plate: Roller: Tension |
| Парткод: | D120 4474 |
| Деталь: | Roller: Tension: Outer |
| Парткод: | AF04 0060 |
| Деталь: | Spring Plate: Roller: Tension: Outer |
| Парткод: | D120 4483 |
| Деталь: | Stopper: Spring Plate: Outer |
| Парткод: | D120 4486 |
| Деталь: | Stopper: Spring Plate |
| Парткод: | D120 4487 |
| Деталь: | Guide Plate: Paper Exit Unit: Lower |
| Парткод: | D120 4452 |
| Деталь: | Ground Plate: Paper Exit Unit |
| Парткод: | D120 4454 |
| Деталь: | Gear: Exit Roller |
| Парткод: | AB01 1297 |
| Деталь: | EXIT ROLLER |
| Парткод: | AF02 0757 |
| Деталь: | Feeler: Paper Feed Sensor |
| Парткод: | D120 4476 |
| Деталь: | Guide Plate: Paper Exit Unit: Upper |
| Парткод: | D120 4453 |
| Деталь: | Stay: Exit |
| Парткод: | D120 4455 |
| Деталь: | Photointerruptor: Lg2a14nl1 |
| Парткод: | AW02 0198 |
| Деталь: | Bracket: Duplex: Lock: Front: Assy |
| Парткод: | D120 1097 |
| Деталь: | Cover: Exit: Sensor |
| Парткод: | D120 4489 |
| Деталь: | Harness: BCU: Paper Feed Sensor |
| Парткод: | D120 5307 |
| Деталь: | Roller: Driven |
| Парткод: | AF02 2180 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Spacer: Exit |
| Парткод: | D120 4456 |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x10 |
| Парткод: | 0802 5320 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Bracket: Paper End Sensor: Manual Feed |
| Парткод: | D039 2724 |
| Деталь: | Feeler: Manual Feed |
| Парткод: | D039 2725 |
| Деталь: | Photointerruptor: LG2A14NHL1 |
| Парткод: | AW02 0198 |
| Деталь: | Torsion Spring: Paper End Sensor |
| Парткод: | D039 2797 |
| Деталь: | Guide Plate: Manual Feed Unit: Upper |
| Парткод: | D120 2626 |
| Деталь: | Plate: Harness: Manual Feed |
| Парткод: | D039 2763 |
| Деталь: | Gear: Cam: Right Rrear |
| Парткод: | D039 2789 |
| Деталь: | Gear: Roller Clutch |
| Парткод: | D039 2780 |
| Деталь: | SEPARATION PAD |
| Парткод: | B261 4650 |
| Деталь: | Gear: Cam: Right |
| Парткод: | D039 2720 |
| Деталь: | Guide Plate: Manual Feed Unit: Lower |
| Парткод: | D120 2613 |
| Деталь: | Holder: Compression Spring: Separation Pad |
| Парткод: | D039 2714 |
| Деталь: | Lever: Compression Spring: Separation Pad |
| Парткод: | D039 2711 |
| Деталь: | Retaining Rings-C: DIA4 |
| Парткод: | D039 2799 |
| Деталь: | Shaft: Drive: Manual Feed Unit |
| Парткод: | D039 2786 |
| Деталь: | By-pass Feed Roller |
| Парткод: | AF03 1060 |
| Деталь: | Cam: Left |
| Парткод: | D039 2793 |
| Деталь: | Gear: Feeler: Left |
| Парткод: | D039 2790 |
| Деталь: | Gear: Cam: Left Rear |
| Парткод: | D039 2722 |
| Деталь: | Bracket: Home Position Sensor |
| Парткод: | D120 2612 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Spring - 2.8n |
| Парткод: | B043 4685 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0805 0089 |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x8 |
| Парткод: | 0802 5319 |
| Деталь: | Clamp: LES-0505 |
| Парткод: | 1105 0551 |
| Деталь: | Bracket: Image Processing Unit |
| Парткод: | D120 5850 |
| Деталь: | PCB: IPU Image Processing Unit |
| Парткод: | D120 5152 |
| Деталь: | Harness: FFC: Image Processing Unit: 2 |
| Парткод: | D120 5316 |
| Деталь: | Harness: FFC: Image Processing Unit: 1 |
| Парткод: | D120 5315 |
| Деталь: | Bracket: FFC: Image Processing Unit |
| Парткод: | D120 5853 |
| Деталь: | Harness: Operation Sub-unit |
| Парткод: | D120 5326 |
| Деталь: | Shadeing Plate: CTL |
| Парткод: | D120 5875 |
| Деталь: | Rack: Application: Upper |
| Парткод: | D120 5856 |
| Деталь: | Fan Motor - Mm60 DC24V |
| Парткод: | AX64 0170 |
| Деталь: | Rack: Application: Lower: Assy |
| Парткод: | D120 5860 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | CLAMP |
| Парткод: | 1105 0516 |
| Деталь: | Screw: Polished Round/Spring: M3x30 |
| Парткод: | 0954 3030N |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0487 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Connector - 54679-1615 |
| Парткод: | 1102 8502 |
| Деталь: | Cover: Harness: Upper |
| Парткод: | D120 2847 |
| Деталь: | Cover: Harness: Lower |
| Парткод: | D120 2848 |
| Деталь: | Paper Feed Unit: Assy |
| Парткод: | D120 2700 |
| Деталь: | Guide Plate: Swivel: No.2 |
| Парткод: | D120 2963 |
| Деталь: | Bracket: Cover: Rear |
| Парткод: | D120 5699 |
| Деталь: | Cover: Duplex: Lower |
| Парткод: | D120 2967 |
| Деталь: | Guide Plate: Vertical Transport: Right |
| Парткод: | D120 2962 |
| Деталь: | Spring: Cover: Manual Feed |
| Парткод: | B223 2665 |
| Деталь: | Bracket: Paper Feed Unit |
| Парткод: | D120 1119 |
| Деталь: | Guide Plate: Vertical Transport: Left |
| Парткод: | D120 2961 |
| Деталь: | GUIDE PLATE |
| Парткод: | D009 2836 |
| Деталь: | Bracket: Cover: Front |
| Парткод: | D120 5698 |
| Деталь: | Electromagnetic Clutch: Registration: 0.5NM |
| Парткод: | AX20 0325 |
| Деталь: | Pulley: Gear: Electromagnetic Clutch: Connecting |
| Парткод: | AB03 0858 |
| Деталь: | Pulley: Registration: Tightener |
| Парткод: | D120 1175 |
| Деталь: | Bracket: Drive: Tightener: Peen |
| Парткод: | D120 1172 |
| Деталь: | Tension Spring: Arm: Coupling |
| Парткод: | B238 4717 |
| Деталь: | Pulley: Transport: No.1 |
| Парткод: | AB03 0857 |
| Деталь: | Gear: Transport: No.2 |
| Парткод: | AB01 0406 |
| Деталь: | Synchronous Belt: Transport: S3M: 5x387 |
| Парткод: | AA04 3671 |
| Деталь: | Electromagnetic Clutch: 0.45NM: Z44 |
| Парткод: | AX20 0324 |
| Деталь: | Pulley: Connecting: Paper Feed: Registration |
| Парткод: | AB03 0859 |
| Деталь: | Synchronous Belt: S2M: 288 |
| Парткод: | AA04 3674 |
| Деталь: | Gear: Idler: Paper Feed: Vertical Transport |
| Парткод: | AB01 1568 |
| Деталь: | Pulley: Paper Feed: NO.2 |
| Парткод: | AB03 0860 |
| Деталь: | Bracket: Paper Feed: Vertical Transport |
| Парткод: | D120 1170 |
| Деталь: | Screw: PCU |
| Парткод: | B259 1131 |
| Деталь: | Harness: Development: Drawer |
| Парткод: | D120 5344 |
| Деталь: | Feeler: Paper Size Sensor: Inner Back |
| Парткод: | D120 2723 |
| Деталь: | Bracket: Paper Size Sensor: Inner Back |
| Парткод: | D120 2724 |
| Деталь: | Photointerruptor: LGRC102 |
| Парткод: | AW02 0204 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Harness: Connecting: Right: Door Switch |
| Парткод: | D120 5338 |
| Деталь: | Charge Receptacle |
| Парткод: | D019 3461 |
| Деталь: | Receptacle - Transfer/Separation |
| Парткод: | D019 3950 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Screw - M3X6 |
| Парткод: | 0954 3006N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Ring Separator |
| Парткод: | 0805 0097 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0805 0088 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Gate Pawl: Lower |
| Парткод: | AF02 5045 |
| Деталь: | Coil Spring: Gate Pawl: Lower |
| Парткод: | AA06 6414 |
| Деталь: | ROLLER TENSION |
| Парткод: | B300 4566 |
| Деталь: | Screw: MM5: 2.5MM |
| Парткод: | GA14 3003 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0156 |
| Деталь: | Tension Roller Shaft |
| Парткод: | AA14 5818 |
| Деталь: | Guide Plate: Open And Close: Gate |
| Парткод: | D120 4665 |
| Деталь: | Inner Cover: Rear |
| Парткод: | D120 4628 |
| Деталь: | Inner Cover: Front |
| Парткод: | D120 4629 |
| Деталь: | Inner Cover: Grip: Duplex Unit |
| Парткод: | D120 4645 |
| Деталь: | Spring - Exit |
| Парткод: | 5205 4527 |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x8 |
| Парткод: | 0802 5319 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0805 0089 |
| Деталь: | Edge Saddle - Les-1010 |
| Парткод: | 1105 0518 |
| Деталь: | Clamp: LES-0505 |
| Парткод: | 1105 0551 |
| Деталь: | Cleaner: Registration: Assy |
| Парткод: | D120 2755 |
| Деталь: | Bracket: Cleaner: Registration |
| Парткод: | D120 2757 |
| Деталь: | Registration Roller: Drive: DIA18.21: Assy |
| Парткод: | AF02 0763 |
| Деталь: | Registration Roller: Driven: Assy |
| Парткод: | AF02 1087 |
| Деталь: | Bracket: Registration Guide: Rear |
| Парткод: | D120 2827 |
| Деталь: | Bracket: Registration Guide: Front |
| Парткод: | D120 2826 |
| Деталь: | Knob: Registration Roller: Assy |
| Парткод: | D120 2819 |
| Деталь: | Guide Plate: Registration: Left: Assy |
| Парткод: | D120 2690 |
| Деталь: | Bushing - Driven Roller |
| Парткод: | D019 2823 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2116 |
| Деталь: | Tension Spring: Registration: Driven |
| Парткод: | D120 2829 |
| Деталь: | Guide Plate: Registration: Left: Auxiliary |
| Парткод: | D120 2699 |
| Деталь: | Guide Plate: Registration: Right |
| Парткод: | D120 2694 |
| Деталь: | Harness: Connecting: Registration Sensor |
| Парткод: | D120 5337 |
| Деталь: | Photo Reflection Sensor: Exit |
| Парткод: | GW01 0007 |
| Деталь: | Bracket: Registration Sensor |
| Парткод: | D120 2697 |
| Деталь: | Guide Plate: Registration: Left |
| Парткод: | D120 2692 |
| Деталь: | Bracket: Heater: PCU |
| Парткод: | D120 5641 |
| Деталь: | Discharge Lamp: C1: Assy |
| Парткод: | D120 3452 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 5215 2621 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Clamps: WES-0507 |
| Парткод: | 1105 0723 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Paper Feed Unit: Assy |
| Парткод: | D120 2700 |
| Деталь: | Feeler: Paper End |
| Парткод: | D089 2767 |
| Деталь: | Photointerruptor: LGRC102 |
| Парткод: | AW02 0204 |
| Деталь: | Harness: Paper Feed Unit |
| Парткод: | D120 5353 |
| Деталь: | Bracket: Sensor: Feed |
| Парткод: | D089 2778 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0128 |
| Деталь: | Bracket: Sensor |
| Парткод: | D089 2781 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0122 |
| Деталь: | DC Solenoid 24V |
| Парткод: | B223 2780 |
| Деталь: | STAY |
| Парткод: | B223 2776 |
| Деталь: | Transport Roller: Drive |
| Парткод: | AF02 0764 |
| Деталь: | Plain Shaft Bearing: DIA6 |
| Парткод: | AA08 2152 |
| Деталь: | Harness Sheet |
| Парткод: | B223 2772 |
| Деталь: | Ground Plate - Front |
| Парткод: | B223 2786 |
| Деталь: | Paper Feed Roller: Pickup |
| Парткод: | AF03 0090 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1252 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | Guide: Feed |
| Парткод: | D089 2829 |
| Деталь: | Paper Feed Roller: Feed |
| Парткод: | AF03 1090 |
| Деталь: | Gear - Roller Clutch |
| Парткод: | AB01 1218 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Ground Plate - Feed |
| Парткод: | B223 2765 |
| Деталь: | Arm: Pickup |
| Парткод: | D089 2761 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0691 |
| Деталь: | Lever - Feed |
| Парткод: | G065 2767 |
| Деталь: | Gear: Feed |
| Парткод: | D089 2764 |
| Деталь: | Shaft: Feed: Assy |
| Парткод: | D120 2762 |
| Деталь: | Paper Feed Roller: Separate |
| Парткод: | AF03 2090 |
| Деталь: | TORQUE LIMITER |
| Парткод: | B004 2783 |
| Деталь: | Shaft: Separate: Driven: Assy |
| Парткод: | D120 2810 |
| Деталь: | Gear: Separate: Drive |
| Парткод: | AB01 0157 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0693 |
| Деталь: | PRESSURE LEVER |
| Парткод: | G065 2774 |
| Деталь: | Gear: Separate: Drive |
| Парткод: | AB01 0156 |
| Деталь: | Separate Drive Shaft |
| Парткод: | B223 2815 |
| Деталь: | Gear: Separator: Input |
| Парткод: | D089 2819 |
| Деталь: | Snap Ring |
| Парткод: | 5206 2686 |
| Деталь: | Release Lever |
| Парткод: | G065 2776 |
| Деталь: | LINK LEVER |
| Парткод: | G065 2775 |
| Деталь: | Spring - Release |
| Парткод: | AA06 2259 |
| Деталь: | Discharge Brush: Paper Feed Unit: Upper |
| Парткод: | D120 2618 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0805 0089 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Tapping Screw: 3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | Toner Supply Unit: Ctype: Assy |
| Парткод: | D120 3503 |
| Деталь: | Cam: Handle |
| Парткод: | D120 3605 |
| Деталь: | Shaft: Chuck |
| Парткод: | D120 3572 |
| Деталь: | Toner Slider |
| Парткод: | A184 3422 |
| Деталь: | Chuck Spring - Tonner Bottle |
| Парткод: | A267 3556 |
| Деталь: | Slider: Assy |
| Парткод: | D120 3573 |
| Деталь: | Chuck: Bottle |
| Парткод: | D120 3571 |
| Деталь: | Cover: Toner Bottle: Ctype: Sub-assy |
| Парткод: | D120 3568 |
| Деталь: | Spacer: Dc Motor: Toner Bottle |
| Парткод: | D120 3620 |
| Деталь: | DC Motor: Toner Bottle: Z: R-C5.5: Assy |
| Парткод: | D085 3616 |
| Деталь: | Bracket: Dc Motor: Toner Bottle: Z: EXP |
| Парткод: | D120 7440 |
| Деталь: | Guide Plate: Toner Supply Unit: Assy |
| Парткод: | D120 5608 |
| Деталь: | Cushion: Remove Paper Dust: Upper |
| Парткод: | D120 2925 |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x8 |
| Парткод: | 0802 5319 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Binding Head Tapping Screw: ES: 3x8 |
| Парткод: | 0802 5317 |
| Деталь: | Guide Plate: Vertical Transport: Lower |
| Парткод: | D120 2956 |
| Деталь: | Sheet: Guide: Vertical Transport: Lower |
| Парткод: | D120 2958 |
| Деталь: | Transport Belt: Driven: Vertical Transport |
| Парткод: | D029 2677 |
| Деталь: | Pulley - Idler |
| Парткод: | D009 2574 |
| Деталь: | Pulley - Vertical Transport |
| Парткод: | D009 2573 |
| Деталь: | Holder - Vertical Transport |
| Парткод: | D009 2571 |
| Деталь: | Shaft - Idler |
| Парткод: | D009 2575 |
| Деталь: | Shaft - Vertical Transport |
| Парткод: | D009 2576 |
| Деталь: | BUSHING - M4 |
| Парткод: | G060 2652 |
| Деталь: | Spring - 11n |
| Парткод: | B223 2676 |
| Деталь: | Guide Plate: Vertical Transport: Driven: Upper |
| Парткод: | D120 2957 |
| Деталь: | Hook: Stopper: Rear |
| Парткод: | D120 4699 |
| Деталь: | Tension Spring: Lever: Duplex |
| Парткод: | AA06 1105 |
| Деталь: | Shaft: Grip |
| Парткод: | D039 2998 |
| Деталь: | Grip: Cover: Right |
| Парткод: | D120 2996 |
| Деталь: | Hook: Stopper: Duplex Unit: Front |
| Парткод: | D039 2996 |
| Деталь: | Timing Belt: S2M288 |
| Парткод: | AA04 3584 |
| Деталь: | Cover: Right |
| Парткод: | D120 4618 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | PCU: EXP: Assy |
| Парткод: | D120 3000 |
| Деталь: | Pickoff Pawl |
| Парткод: | B039 2335 |
| Деталь: | Drum Shutter |
| Парткод: | B039 2343 |
| Деталь: | Clip - OPC DRUM |
| Парткод: | B039 2350 |
| Деталь: | Blade: Cleaning |
| Парткод: | AD04 1114 |
| Деталь: | Gear - 13Z |
| Парткод: | AB01 1403 |
| Деталь: | Gear - 14Z |
| Парткод: | AB01 1402 |
| Деталь: | Roller: Charge: A3 |
| Парткод: | AD02 7018 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3444 |
| Деталь: | Charge Cleaner Brush Roller |
| Парткод: | AD04 2058 |
| Деталь: | Charge Roller Spring |
| Парткод: | B039 2287 |
| Деталь: | Front Pressure Arm - Charge Roller |
| Парткод: | B039 2292 |
| Деталь: | Pin - Front Pressure Arm |
| Парткод: | B039 2293 |
| Деталь: | Arm: Pressure: Charge: Rear |
| Парткод: | D120 3174 |
| Деталь: | Electrode Plate: Roller: Charge: Assy |
| Парткод: | D120 3175 |
| Деталь: | Gear: Idler: Toner Recycling |
| Парткод: | D120 3183 |
| Деталь: | Cover: PCU: Front: Assy |
| Парткод: | D120 3180 |
| Деталь: | Shutter: PCU |
| Парткод: | D120 3193 |
| Деталь: | Compression Spring: Shutter: PCU |
| Парткод: | A267 3194 |
| Деталь: | Drum Stay: Front: Assy |
| Парткод: | D120 3210 |
| Деталь: | Drum Stay: Rear: Sub-assy |
| Парткод: | D120 3233 |
| Деталь: | Development Roller: Assy |
| Парткод: | D120 3320 |
| Деталь: | Development Roller Gear |
| Парткод: | B039 3060 |
| Деталь: | Idler Gear - 16z |
| Парткод: | B039 3062 |
| Деталь: | Case: Development Roller: Assy |
| Парткод: | D120 3360 |
| Деталь: | Case: Development: Assy |
| Парткод: | D120 3371 |
| Деталь: | Joint: Development |
| Парткод: | D120 3440 |
| Деталь: | OPC Drum |
| Парткод: | B039 9510 |
| Деталь: | Developer Type 28 Black |
| Парткод: | B121 9640 |
| Деталь: | Tapping Screw: 3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Binding Self-tapping Screw: 3x6 |
| Парткод: | 0452 3006N |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x8 |
| Парткод: | 0802 5319 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Bracket: Grip: Rear Right |
| Парткод: | D120 5826 |
| Деталь: | Grip: Rear Right |
| Парткод: | D120 5828 |
| Деталь: | Bracket: Grip: Support |
| Парткод: | D120 5834 |
| Деталь: | DC Motor 24V |
| Парткод: | AX04 0154 |
| Деталь: | COVER |
| Парткод: | B223 2722 |
| Деталь: | Cover: Tray: Right |
| Парткод: | D120 2541 |
| Деталь: | Bracket: Push Switch |
| Парткод: | B223 2721 |
| Деталь: | Push Switch: Paper Size Sensor |
| Парткод: | AW50 0038 |
| Деталь: | Cover: Tray: Left |
| Парткод: | D120 2543 |
| Деталь: | Cover - Positioning Pin |
| Парткод: | B238 1089 |
| Деталь: | Bracket: Base |
| Парткод: | D120 1091 |
| Деталь: | Cover - Connector |
| Парткод: | B238 1088 |
| Деталь: | Bracket: Connector: Base |
| Парткод: | D120 1096 |
| Деталь: | Rubber Foot Cover |
| Парткод: | B238 1066 |
| Деталь: | Cushion: Electromagnetic Clutch: Paper Feed |
| Парткод: | D120 2820 |
| Деталь: | Connector - QR/P17-14S-B |
| Парткод: | 1102 8534 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw: 3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0487 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Optical Writing Unit: Assy |
| Парткод: | D120 1860 |
| Деталь: | Block: Positioning Pin: Optical Writing Unit |
| Парткод: | D120 1928 |
| Деталь: | DC Polygon Mirror Motor: Brushless: 19.2W |
| Парткод: | AX06 0403 |
| Деталь: | Harness: DC Polygon Mirror Motor |
| Парткод: | D120 5224 |
| Деталь: | PCB: Sync Detector |
| Парткод: | D009 5325 |
| Деталь: | Harness: Sync Detector |
| Парткод: | D120 5222 |
| Деталь: | Laser Diode Unit: Assy |
| Парткод: | D120 1891 |
| Деталь: | Harness: LD |
| Парткод: | D120 5223 |
| Деталь: | Shield Glass |
| Парткод: | AC01 5052 |
| Деталь: | Decal - LD |
| Парткод: | G029 1980 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Binding Head Tapping Screw: Es: 3x10 |
| Парткод: | 0802 5318 |
| Деталь: | Binding Head Tapping Screw: ES: 3x8 |
| Парткод: | 0802 5317 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Transport Roller: Duplex: Entrance |
| Парткод: | AF02 0755 |
| Деталь: | Link: Stopper |
| Парткод: | D120 4677 |
| Деталь: | Gear: Transport Roller |
| Парткод: | AB01 1295 |
| Деталь: | Torsion Spring: Stopper |
| Парткод: | AA06 6416 |
| Деталь: | Shaft: Cam: Assy |
| Парткод: | D039 2796 |
| Деталь: | Arm: Stopper |
| Парткод: | D120 4673 |
| Деталь: | Bracket: Arm: Stopper |
| Парткод: | D120 4655 |
| Деталь: | Torsion Spring: Stopper: Contact Point |
| Парткод: | AA06 6410 |
| Деталь: | Gear: Idler: Duplex: Exit |
| Парткод: | AB01 1296 |
| Деталь: | Timing Belt: 40S2M120 |
| Парткод: | AA04 3323 |
| Деталь: | Ground Plate - Stepper Motor |
| Парткод: | B238 1762 |
| Деталь: | Sheet: Guide Plate: Manual Feed |
| Парткод: | D120 2614 |
| Деталь: | Gear: Stepper Motor |
| Парткод: | D039 2781 |
| Деталь: | Bracket: Cover: Right |
| Парткод: | D120 4612 |
| Деталь: | DC Stepper Motor: Duplex: 2.32W |
| Парткод: | D120 4671 |
| Деталь: | Harness: Duplex Unit: Main |
| Парткод: | D120 5350 |
| Деталь: | Stepper Motor: Transport |
| Парткод: | AX05 0302 |
| Деталь: | Harness: Manual Feed Unit: Main |
| Парткод: | D120 5357 |
| Деталь: | Spacer: Duplex: Contact Point: Rear |
| Парткод: | D120 4609 |
| Деталь: | Spacer: Duplex: Connect Point: Front |
| Парткод: | D120 4610 |
| Деталь: | Link: Front: Duplex: Assy |
| Парткод: | D120 4625 |
| Деталь: | Pulley: Transport Roller |
| Парткод: | AB03 0848 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Screw - M3X4 |
| Парткод: | 0353 0040N |
| Деталь: | CLAMP |
| Парткод: | 1105 0516 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Duct: DC Fan Motor |
| Парткод: | D120 1102 |
| Деталь: | Duct: Upper |
| Парткод: | D120 1105 |
| Деталь: | Duct: Lower |
| Парткод: | D120 1104 |
| Деталь: | Holder: Duct |
| Парткод: | D120 1108 |
| Деталь: | Bracket: DC Fan Motor: MM60 |
| Парткод: | D120 1127 |
| Деталь: | Fan Motor - Mm60 DC24V |
| Парткод: | AX64 0170 |
| Деталь: | Harness: Connecting: Duplex Section: Fan |
| Парткод: | D120 5346 |
| Деталь: | Bracket: SDB |
| Парткод: | D120 5874 |
| Деталь: | PCB: SDB |
| Парткод: | M026 5194 |
| Деталь: | Guide Plate: Duct: Exhaust |
| Парткод: | D120 1106 |
| Деталь: | Fan Motor: MM80 DC24V 3.12W |
| Парткод: | GX64 5734 |
| Деталь: | Bracket: Protect: Side Plate: Left Rear |
| Парткод: | D120 1085 |
| Деталь: | Tapping Screw: 3x30 |
| Парткод: | 0451 3030N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw: 4x35 |
| Парткод: | 0451 4035N |
| Деталь: | Clamps: WES-1210 |
| Парткод: | 1105 0724 |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 1105 0508 |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x10 |
| Парткод: | 0802 5320 |
| Деталь: | Clamps: WES-2217 |
| Парткод: | 1105 0726 |
| Деталь: | Clamps: WES-1117 |
| Парткод: | 1105 0725 |
| Деталь: | CLAMP |
| Парткод: | 1105 0516 |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0488 |
| Деталь: | Reverse Roller |
| Парткод: | AF02 0758 |
| Деталь: | Ground Plate: Reverse Roller |
| Парткод: | D120 4837 |
| Деталь: | Frame: Reverse Roller |
| Парткод: | D120 4840 |
| Деталь: | Gear: Reverse Roller |
| Парткод: | AB01 1298 |
| Деталь: | Timing Pulley: 19T: Gear: Z24 |
| Парткод: | AB03 0853 |
| Деталь: | Synchronous Belt: S3M: 150 |
| Парткод: | AA04 3648 |
| Деталь: | Cover: Motor: Reverse |
| Парткод: | D120 4833 |
| Деталь: | Gear: Idler |
| Парткод: | AB01 0162 |
| Деталь: | Side Plate: Reverse: Rear: Assy |
| Парткод: | D120 4811 |
| Деталь: | Gear: Z31 |
| Парткод: | AB01 0161 |
| Деталь: | Seal: Reverse Roller |
| Парткод: | AA00 0273 |
| Деталь: | Bracket: DC Stepper Motor |
| Парткод: | D120 4810 |
| Деталь: | DC Stepper Motor: 14.4W |
| Парткод: | AX06 0401 |
| Деталь: | Pulley: Transport Roller: Reverse |
| Парткод: | AB03 0849 |
| Деталь: | Transport Roller: Reverse |
| Парткод: | AF02 0759 |
| Деталь: | Bracket: Photo Refiection Sensor: Reverse |
| Парткод: | D120 4834 |
| Деталь: | Photo Reflection Sensor: Exit |
| Парткод: | GW01 0007 |
| Деталь: | Harness: Reverse Unit |
| Парткод: | D120 5355 |
| Деталь: | Bracket: DC Solenoid |
| Парткод: | D120 4828 |
| Деталь: | Frame: Reverse |
| Парткод: | D120 4830 |
| Деталь: | Reverse Roller: Driven |
| Парткод: | AF02 0778 |
| Деталь: | Plain Shaft Bearing: DIA4 |
| Парткод: | AA08 0297 |
| Деталь: | Coil Spring: Reverse Roller: Driven |
| Парткод: | AA06 3478 |
| Деталь: | Link: Gate Pawl: Lower |
| Парткод: | D120 4829 |
| Деталь: | Coil Spring: Link: Gate Pawl: Lower |
| Парткод: | AA06 6415 |
| Деталь: | DC Solenoid: 24V: 2.9N |
| Парткод: | D120 4827 |
| Деталь: | Side Plate: Reverse: Front: Assy |
| Парткод: | D120 4823 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Screw - M3X4 |
| Парткод: | 0353 0040N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0805 0089 |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x8 |
| Парткод: | 0802 5319 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Clamps: WES-0507 |
| Парткод: | 1105 0723 |
| Деталь: | Cover: Left |
| Парткод: | D120 1280 |
| Деталь: | Cover: Left Rear |
| Парткод: | D120 1281 |
| Деталь: | Cover: Paper Exit Sub-unit: Right Lower |
| Парткод: | D120 1305 |
| Деталь: | Cover: Paper Exit Sub-unit: Rear |
| Парткод: | D120 1300 |
| Деталь: | Cover: Paper Exit Sub-unit: Inner Back |
| Парткод: | D120 1309 |
| Деталь: | Cover: Paper Exit Sub-unit: Rear Lower |
| Парткод: | D120 1342 |
| Деталь: | Cover: Right Front |
| Парткод: | D120 1272 |
| Деталь: | Inner Cover: Grip: Duplex Unit |
| Парткод: | D120 4645 |
| Деталь: | Cover: Right |
| Парткод: | D120 1270 |
| Деталь: | Cover: Right Rear |
| Парткод: | D120 1271 |
| Деталь: | Cover: Rear: Lower |
| Парткод: | D120 1290 |
| Деталь: | Cover: Rear: Upper |
| Парткод: | D120 1291 |
| Деталь: | Cap: Cover |
| Парткод: | D120 1337 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - 3x8 |
| Парткод: | 0451 3008P |
| Деталь: | Lever: Lock: Pressure |
| Парткод: | D120 4197 |
| Деталь: | Side Plate: Fusing: Front |
| Парткод: | D120 4121 |
| Деталь: | Lever: Pressure Release: Front: Assy |
| Парткод: | D120 4171 |
| Деталь: | Lever: Pressure Roller: Front |
| Парткод: | D120 4116 |
| Деталь: | Grip: Pressure: Change |
| Парткод: | D120 4112 |
| Деталь: | Lever: Pressure Release: Rear: Assy |
| Парткод: | D120 4191 |
| Деталь: | Lever: Pressure Roller: Rear |
| Парткод: | D120 4117 |
| Деталь: | Shaft: Pressure: Change |
| Парткод: | AA14 0794 |
| Деталь: | Electrode Plate: Thermostat: Rear |
| Парткод: | D120 4093 |
| Деталь: | Electrode Plate: Thermostat: Connecting |
| Парткод: | D120 4092 |
| Деталь: | Thermostat: Assy |
| Парткод: | D120 4095 |
| Деталь: | Housing: Thermostat |
| Парткод: | D120 4094 |
| Деталь: | Sheet: Plate: Harness |
| Парткод: | D120 4079 |
| Деталь: | Fusing Cleaning Roller |
| Парткод: | AE04 2029 |
| Деталь: | Roller Busing |
| Парткод: | AA08 2073 |
| Деталь: | Compression Spring: Fusing Cleaning Roller: 5N |
| Парткод: | AA06 3699 |
| Деталь: | Side Plate: Fusing: Rear |
| Парткод: | D120 4125 |
| Деталь: | Link: Release: Drive |
| Парткод: | D120 4082 |
| Деталь: | Lever: Release: Drive |
| Парткод: | D120 4083 |
| Деталь: | Spring: Release: Drive |
| Парткод: | AA06 6411 |
| Деталь: | Cover: Thermostat |
| Парткод: | D120 4078 |
| Деталь: | Sheet: Thermostat |
| Парткод: | D120 4080 |
| Деталь: | Frame: Fusing: Lower |
| Парткод: | D120 4072 |
| Деталь: | Decal: H-temp Warning |
| Парткод: | D120 4183 |
| Деталь: | Decal: H-temp Warning: EU |
| Парткод: | D120 4187 |
| Деталь: | Ground Plate: Fusing Entrance Guide Plate |
| Парткод: | D120 4086 |
| Деталь: | Fusing Entrance Guide Plate: Right |
| Парткод: | D120 4085 |
| Деталь: | Thermistor - Rear |
| Парткод: | AW10 0053 |
| Деталь: | Holder: Thermistor |
| Парткод: | D120 4099 |
| Деталь: | Spacer: Safety Switch: Fusing Unit |
| Парткод: | D120 4076 |
| Деталь: | Guide: Paper: Rail: PCU |
| Парткод: | A232 2374 |
| Деталь: | Electrode Plate: Thermostat: Front |
| Парткод: | D120 4091 |
| Деталь: | Decal: Exchange Indication: Envelope |
| Парткод: | D120 4182 |
| Деталь: | Roller: Lever: Pressure |
| Парткод: | B238 4194 |
| Деталь: | Screw: Drawer |
| Парткод: | AA14 3792 |
| Деталь: | Plain Shaft Bearing: Fusing |
| Парткод: | D120 4208 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Hexagonal Bolt: Double Screw: M3x8 |
| Парткод: | 0804 6127 |
| Деталь: | Relay Connector - 3P |
| Парткод: | 1102 6260 |
| Деталь: | Screw - M3x12 |
| Парткод: | 0954 3012N |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x10 |
| Парткод: | 0802 5320 |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Fusing Unit: NA: Assy |
| Парткод: | D120 4001 |
| Деталь: | Fusing Unit: EU: Assy |
| Парткод: | D120 4002 |
| Деталь: | Frame: Fusing: Upper: Assy |
| Парткод: | D120 4032 |
| Деталь: | Decal: Grip: Guide Plate: Fusing Exit |
| Парткод: | D120 4181 |
| Деталь: | Spring: Open And Close: Guide |
| Парткод: | AA06 6418 |
| Деталь: | Hot Roller Stripper |
| Парткод: | AE04 4025 |
| Деталь: | Compression Spring: Stripper Pawls |
| Парткод: | AA06 3697 |
| Деталь: | Tension Spring: Pressure: 34.2N |
| Парткод: | AA06 6412 |
| Деталь: | Bracket: Stripper Pawls |
| Парткод: | D120 4101 |
| Деталь: | Harness: Drawer: Fusing: 120V: NA |
| Парткод: | D120 5274 |
| Деталь: | Harness: Drawer: Fusing: 230V: EU |
| Парткод: | D120 5275 |
| Деталь: | Heater: 120V: Sub |
| Парткод: | AX44 0353 |
| Деталь: | Heater: Infrared: 230V/600W: SUB |
| Парткод: | AX44 0355 |
| Деталь: | Heater: 120V: Main |
| Парткод: | AX44 0352 |
| Деталь: | Heater: Infrared: 230V/600W: Main |
| Парткод: | AX44 0354 |
| Деталь: | Gear - 48Z |
| Парткод: | AB01 1400 |
| Деталь: | Bearing 30x42x7 |
| Парткод: | G052 4618 |
| Деталь: | Hot Roller: DIA40: T0.4 |
| Парткод: | AE01 1128 |
| Деталь: | Pressure Roller: MM27 |
| Парткод: | AE02 0161 |
| Деталь: | Spring: Flange: Pressure Roller |
| Парткод: | AA06 3698 |
| Деталь: | Ball Bearing - 8x19x6 |
| Парткод: | AE03 0030 |
| Деталь: | Knob Screw: Fix: Fusing |
| Парткод: | D120 4161 |
| Деталь: | Guide: Harness: Plate |
| Парткод: | D120 4077 |
| Деталь: | Stopper: External Circlip |
| Парткод: | D120 4071 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3219 |
| Деталь: | Decal: H-temp Warning: Small |
| Парткод: | D120 4184 |
| Деталь: | Terminal: Heater |
| Парткод: | D120 4090 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Retaining Ring C - M30 |
| Парткод: | 0725 0300E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Hexagonal Bolt: Double Screw: M3x8 |
| Парткод: | 0804 6127 |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x10 |
| Парткод: | 0802 5320 |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Manual Feed Table: Assy |
| Парткод: | D120 2605 |
| Деталь: | Side Fence: Front |
| Парткод: | D120 2747 |
| Деталь: | Decal: Side Fence: Manual Feed |
| Парткод: | D120 2632 |
| Деталь: | Side Fence: Rear |
| Парткод: | D120 2750 |
| Деталь: | Friction Pad: 10x50 |
| Парткод: | AF03 3008 |
| Деталь: | Bottom Plate Pad |
| Парткод: | B039 2628 |
| Деталь: | Disc: Side Fence |
| Парткод: | D039 2752 |
| Деталь: | Rack: Side Fence: Rear |
| Парткод: | D039 2751 |
| Деталь: | Decal: Scale: Manual Feed |
| Парткод: | D120 2651 |
| Деталь: | Decal: Manual Feed: Inkjet: EXP |
| Парткод: | D120 2631 |
| Деталь: | Cover: Paper: Trailing Edge |
| Парткод: | D120 2638 |
| Деталь: | Feeler: Paper: Trailing Edge |
| Парткод: | D039 2737 |
| Деталь: | Harness: Connecting: Manual Feed Unit: Sensor |
| Парткод: | D120 5358 |
| Деталь: | Paper size sensor |
| Парткод: | AW50 0037 |
| Деталь: | Link: Manual Feed Table |
| Парткод: | D120 2696 |
| Деталь: | Photointerruptor: Lg2a14nl1 |
| Парткод: | AW02 0198 |
| Деталь: | Extension Tray: Manual Feed |
| Парткод: | D120 2740 |
| Деталь: | Spring Plate: Extension Tray |
| Парткод: | D039 2779 |
| Деталь: | Pin: Side Fence |
| Парткод: | D039 2788 |
| Деталь: | Spring: Side Fence |
| Парткод: | D039 2754 |
| Деталь: | Gear: Side Fence |
| Парткод: | D039 2753 |
| Деталь: | Spring: Base: 2.5N |
| Парткод: | D039 2798 |
| Деталь: | Cover: Manual Feed Table |
| Парткод: | D120 2736 |
| Деталь: | Rack: Side Fence: Front |
| Парткод: | D039 2750 |
| Деталь: | Base: Manual Feed Table: Assy |
| Парткод: | D120 2744 |
| Деталь: | Decal: Cover: Right |
| Парткод: | D120 4643 |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x8 |
| Парткод: | 0802 5319 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0805 0089 |
| Деталь: | CT Connector - 8P |
| Парткод: | 1102 4431 |
| Деталь: | Cover: Grip: Left |
| Парткод: | D120 5625 |
| Деталь: | Grip: Left |
| Парткод: | D120 5624 |
| Деталь: | Bracket: Grip: Left Rear |
| Парткод: | D120 1077 |
| Деталь: | Frame: Lengthwise: Right Front |
| Парткод: | D120 1078 |
| Деталь: | Stay: Scanner: Right Lower |
| Парткод: | D120 1080 |
| Деталь: | Frame: Lengthwise: Right Rear |
| Парткод: | D120 1079 |
| Деталь: | Bracket: Link: Main: Assy |
| Парткод: | D120 5604 |
| Деталь: | Guide: Harness: Paper Feed: Inner Back |
| Парткод: | D120 2816 |
| Деталь: | Bracket: Cover: Rear |
| Парткод: | D120 5615 |
| Деталь: | Supporter - Right |
| Парткод: | B223 2715 |
| Деталь: | Hinge: Door: Front: Right |
| Парткод: | D120 1386 |
| Деталь: | Bracket: Grip: Front: Left And Right |
| Парткод: | D120 1082 |
| Деталь: | Rubber Pad - H5 |
| Парткод: | AH01 0009 |
| Деталь: | Supporter: Left: Assy |
| Парткод: | D120 2710 |
| Деталь: | Hinge: Door: Front: Left |
| Парткод: | D120 1387 |
| Деталь: | Cover: Grip: Right Front |
| Парткод: | D120 5623 |
| Деталь: | Grip: Right Front: Assy |
| Парткод: | D120 5620 |
| Деталь: | Positioning Cap - Short |
| Парткод: | B223 2714 |
| Деталь: | CUSHION |
| Парткод: | AA16 1163 |
| Деталь: | Tapping Screw: 4x8 |
| Парткод: | 0451 4008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | CLAMP |
| Парткод: | 1105 0516 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | CLAMP |
| Парткод: | 1105 0534 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | PCB: CTL: ORV-C1: 23CPM |
| Парткод: | D122 5720 |
| Деталь: | PCB: CTL: ORV-C1: 28CPM |
| Парткод: | D122 5740 |
| Деталь: | PCB: CTL: ORV-C1: 33CPM |
| Парткод: | D122 5750 |
| Деталь: | NVRAM |
| Парткод: | D120 9590 |
| Деталь: | Rail: Right: Small |
| Парткод: | D009 5899 |
| Деталь: | Rail: Left: Fax Control Unit |
| Парткод: | D009 5891 |
| Деталь: | PCB: Memory: 512MB |
| Парткод: | M052 5391 |
| Деталь: | Bracket: SATIE2 |
| Парткод: | D120 5692 |
| Деталь: | PCB: SATIE2 |
| Парткод: | D129 5710 |
| Деталь: | Bracket: HDD |
| Парткод: | D120 5691 |
| Деталь: | Cable: HDD: SATA: 135 |
| Парткод: | D129 5713 |
| Деталь: | HDD: 160GB: MK1676GSX |
| Парткод: | M080 5320 |
| Деталь: | Cable: HDD: SATA: Power: 2P |
| Парткод: | D129 5719 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | AA14 3848 |
| Деталь: | Rubber Cushion |
| Парткод: | AA16 1125 |
| Деталь: | Bracket: Control Board: NO.2: Assy |
| Парткод: | D120 5859 |
| Деталь: | Bracket: Control Board: Assy |
| Парткод: | D120 5868 |
| Деталь: | Panel: Interface |
| Парткод: | D120 5869 |
| Деталь: | Panel: FAX |
| Парткод: | D120 5890 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | CLAMP |
| Парткод: | 1105 0516 |
| Деталь: | Carriage: No.2: Assy |
| Парткод: | D120 1740 |
| Деталь: | Mirror: No.2: Convax: Assy |
| Парткод: | D025 1728 |
| Деталь: | Spring Plate - 2nd Mirror |
| Парткод: | G404 2810 |
| Деталь: | Mirror: No.2: Concave: Assy |
| Парткод: | D025 1727 |
| Деталь: | PULLEY |
| Парткод: | B238 1807 |
| Деталь: | Guide: FFC: Carriage: No.2 |
| Парткод: | D120 1711 |
| Деталь: | Guide: FFC |
| Парткод: | M026 1778 |
| Деталь: | Carriage: No.1: Assy |
| Парткод: | D120 1731 |
| Деталь: | Harness: FFC: LED |
| Парткод: | D120 5203 |
| Деталь: | Guide: FFC: Carriage: No.1 |
| Парткод: | D120 1710 |
| Деталь: | Illumination Unit: LED: Assy |
| Парткод: | D120 1732 |
| Деталь: | Mirror: No.1 |
| Парткод: | AC03 0169 |
| Деталь: | Clamp: MIRROR: NO.1 |
| Парткод: | M026 1815 |
| Деталь: | Wire Clamp |
| Парткод: | A193 1766 |
| Деталь: | Ground Plate: Harness: SBU |
| Парткод: | D039 1705 |
| Деталь: | Guide: FFC: Base |
| Парткод: | D120 1712 |
| Деталь: | Inner Cover: Scanner: Peen |
| Парткод: | D039 1700 |
| Деталь: | Gasket: 9x5.5x17 |
| Парткод: | D105 1703 |
| Деталь: | Clamp - Rear Wire |
| Парткод: | A193 1769 |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Bind Screw - M3x5 |
| Парткод: | 0352 5050N |
| Деталь: | Cap: Cover |
| Парткод: | D120 1337 |
| Деталь: | Cover: Scanner: Left Upper |
| Парткод: | D120 1251 |
| Деталь: | Cover: Scanner: Left Lower |
| Парткод: | D120 1250 |
| Деталь: | Cover: Scanner: Front Upper |
| Парткод: | D120 1255 |
| Деталь: | Decal: Caution: Original: English |
| Парткод: | D120 6441 |
| Деталь: | Cover: Paper Exit Sub-unit: Left |
| Парткод: | D120 1301 |
| Деталь: | Cover: Scanner: Rear |
| Парткод: | D120 1252 |
| Деталь: | Cover: Scanner: Right Upper |
| Парткод: | D120 1254 |
| Деталь: | Cover: Scanner: Right Lower |
| Парткод: | D120 1253 |
| Деталь: | Cap: Cover: Right |
| Парткод: | D120 1344 |
| Деталь: | Cover: Scanner: Front Lower |
| Парткод: | D120 1265 |
| Деталь: | Decal: Model Name Plate: MP2352: EXP |
| Парткод: | D120 8620 |
| Деталь: | Decal: Model Name Plate: MP2352: SVN |
| Парткод: | D120 8621 |
| Деталь: | Decal: Model Name Plate: MP2352: LAN |
| Парткод: | D120 8622 |
| Деталь: | Decal: Model Name Plate: MP2352: GES: NA |
| Парткод: | D120 8623 |
| Деталь: | Decal: Model Name Plate: MP2352: NRG |
| Парткод: | D120 8624 |
| Деталь: | Decal: Model Name Plate: MP2352: INF |
| Парткод: | D120 8625 |
| Деталь: | Decal: Model Name Plate: MP2352SP: EXP |
| Парткод: | D120 8626 |
| Деталь: | Decal: Model Name Plate: MP2352SP: LAN |
| Парткод: | D120 8627 |
| Деталь: | Decal: Model Name Plate: MP2352SP: GES: NA |
| Парткод: | D120 8628 |
| Деталь: | Decal: Model Name Plate: MP2352SP: NRG |
| Парткод: | D120 8629 |
| Деталь: | Decal: Model Name Plate: MP2352SP: INF |
| Парткод: | D120 8630 |
| Деталь: | Decal: Model Name Plate: MP2852: EXP |
| Парткод: | D121 8620 |
| Деталь: | Decal: Model Name Plate: MP2852: SVN |
| Парткод: | D121 8621 |
| Деталь: | Decal: Model Name Plate: MP2852: LAN |
| Парткод: | D121 8622 |
| Деталь: | Decal: Model Name Plate: MP2852: GES: NA |
| Парткод: | D121 8623 |
| Деталь: | Decal: Model Name Plate: MP2852: NRG |
| Парткод: | D121 8624 |
| Деталь: | Decal: Model Name Plate: MP2852: INF |
| Парткод: | D121 8625 |
| Деталь: | Decal: Model Name Plate: MP2852SP: EXP |
| Парткод: | D121 8626 |
| Деталь: | Decal: Model Name Plate: MP2852SP: LAN |
| Парткод: | D121 8627 |
| Деталь: | Decal: Model Name Plate: MP2852SP: GES: NA |
| Парткод: | D121 8628 |
| Деталь: | Decal: Model Name Plate: MP2852SP: NRG |
| Парткод: | D121 8629 |
| Деталь: | Decal: Model Name Plate: MP2852SP: INF |
| Парткод: | D121 8630 |
| Деталь: | Decal: Model Name Plate: MP3352: EXP |
| Парткод: | D122 8620 |
| Деталь: | Decal: Model Name Plate: MP3352: SVN |
| Парткод: | D122 8621 |
| Деталь: | Decal: Model Name Plate: MP3352: LAN |
| Парткод: | D122 8622 |
| Деталь: | Decal: Model Name Plate: MP3352: GES: NA |
| Парткод: | D122 8623 |
| Деталь: | Decal: Model Name Plate: MP3352: NRG |
| Парткод: | D122 8624 |
| Деталь: | Decal: Model Name Plate: MP3352: INF |
| Парткод: | D122 8625 |
| Деталь: | Decal: Model Name Plate: MP3352SP: EXP |
| Парткод: | D122 8626 |
| Деталь: | Decal: Model Name Plate: MP3352SP: LAN |
| Парткод: | D122 8627 |
| Деталь: | Decal: Model Name Plate: MP3352SP: GES: NA |
| Парткод: | D122 8628 |
| Деталь: | Decal: Model Name Plate: MP3352SP: NRG |
| Парткод: | D122 8629 |
| Деталь: | Decal: Model Name Plate: MP3352SP: INF |
| Парткод: | D122 8630 |
| Деталь: | Cover: Scanner: Front Right |
| Парткод: | D120 1259 |
| Деталь: | Tapping Screw: 3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x10 |
| Парткод: | 0802 5320 |
| Деталь: | Tapping Screw - 3x8 |
| Парткод: | 0451 3008P |
| Деталь: | Screw: M3x5 |
| Парткод: | 0353 0050P |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Cover: Drive: Fusing |
| Парткод: | D120 6105 |
| Деталь: | Gear: Exit: Drive |
| Парткод: | AB01 1567 |
| Деталь: | Gear: Fusing: Idler |
| Парткод: | AB01 1565 |
| Деталь: | Guide Plate: Fusing Unit: Rear |
| Парткод: | D120 5613 |
| Деталь: | Bracket: Drive: Fusing |
| Парткод: | D120 1185 |
| Деталь: | Harness: AC: Fusing: NA |
| Парткод: | D120 5321 |
| Деталь: | Harness: AC: Fusing: EU |
| Парткод: | D120 5322 |
| Деталь: | Bracket: Fusing: Swivel |
| Парткод: | D120 1189 |
| Деталь: | Bracket: Arm: Fusing/Paper Exit Unit |
| Парткод: | D120 6111 |
| Деталь: | Lever: DC Solenoid: Assy |
| Парткод: | D120 1193 |
| Деталь: | Synchronous Belt: Fusing: S3M: 5x288 |
| Парткод: | AA04 3673 |
| Деталь: | Pulley: Fusing: NO.2 |
| Парткод: | AB03 0856 |
| Деталь: | Bracket: Drive: Drum: Assy |
| Парткод: | D120 1027 |
| Деталь: | DC Brushless Motor: Main: 30.7W |
| Парткод: | AX06 0402 |
| Деталь: | Pulley: Fusing: No.1 |
| Парткод: | AB03 0855 |
| Деталь: | Gear: Fusing: No.2 |
| Парткод: | AB01 0404 |
| Деталь: | Holder: Registration |
| Парткод: | D120 1178 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3301 |
| Деталь: | Tapping Screw: 3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0805 0089 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Choke Coil |
| Парткод: | B121 5018 |
| Деталь: | Harness: AC: Inlet |
| Парткод: | D120 5314 |
| Деталь: | Bracket: Power Supply Cord |
| Парткод: | D120 5831 |
| Деталь: | Harness: BCU: Door Switch |
| Парткод: | D120 5304 |
| Деталь: | Bracket: Micro Switch |
| Парткод: | D120 5629 |
| Деталь: | Compression Spring: Door Switch |
| Парткод: | AA06 3476 |
| Деталь: | Tension Spring: Door Switch |
| Парткод: | D120 1095 |
| Деталь: | Lever: Door Switch: Assy |
| Парткод: | D120 5602 |
| Деталь: | Harness: SDB: Main Switch |
| Парткод: | D120 5318 |
| Деталь: | Harness: SDB: Switch: 2P |
| Парткод: | D120 5310 |
| Деталь: | Bracket: Main Switch |
| Парткод: | D120 5616 |
| Деталь: | Heater: Nichrome Wire: 120V: 9W: NA |
| Парткод: | D120 2702 |
| Деталь: | Heater: Nichrome Wire: 230V: 9W |
| Парткод: | D120 2705 |
| Деталь: | Cover - Connector |
| Парткод: | B223 2727 |
| Деталь: | Harness: AC: Heater: EXP |
| Парткод: | D120 5319 |
| Деталь: | Harness: AC: Fusing: NA |
| Парткод: | D120 5321 |
| Деталь: | Harness: AC: Fusing: EU |
| Парткод: | D120 5322 |
| Деталь: | Harness: PSU |
| Парткод: | D120 5312 |
| Деталь: | Power Supply Unit: 247W: DOM/NA |
| Парткод: | AZ23 0255 |
| Деталь: | Power Supply Unit: 247W: EU/AA/CHN |
| Парткод: | AZ23 0257 |
| Деталь: | DC Fan Motor: Mm60: 24V |
| Парткод: | AX64 0208 |
| Деталь: | Pin: Bracket: Micro Switch |
| Парткод: | D120 5733 |
| Деталь: | Power Supply Code: 250V: 10A: EU |
| Парткод: | 11 500 377 |
| Деталь: | Power Supply Code: 125V: 15A: TWN |
| Парткод: | 11 500 409 |
| Деталь: | Power Supply Code: AC125V: 15A: NA |
| Парткод: | 11 500 438 |
| Деталь: | Power Supply Cord: CHN |
| Парткод: | GZ00 0005 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | MICRO SWITCH |
| Парткод: | 12 042 510 |
| Деталь: | Pan Head Screw: M3x35 |
| Парткод: | 0313 0350N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Connector: OG-503040V |
| Парткод: | 11 050 574 |
| Деталь: | Retaining Ring - 3m |
| Парткод: | 8 050 092 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 8 025 299 |
| Деталь: | Rocker Switch: RS51-AJAJ |
| Парткод: | 12 042 901 |
| Деталь: | Screw - M4X6 |
| Парткод: | 0950 4006N |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | KGPS-16RF-V0 |
| Парткод: | 11 050 701 |
| Деталь: | Spacer - Kgls-16rt |
| Парткод: | 11 050 296 |
| Деталь: | Scale: Left: A |
| Парткод: | D120 1781 |
| Деталь: | Exposure Glass: Document Feeder |
| Парткод: | D105 1795 |
| Деталь: | Document Feeder Bracket |
| Парткод: | B238 1803 |
| Деталь: | Heater: Option: 120V: 9W |
| Парткод: | B229 1687 |
| Деталь: | Heater: Option: 230V: 9W |
| Парткод: | B229 1688 |
| Деталь: | Scale: Left: B: DOM/EU: Assy |
| Парткод: | D120 1783 |
| Деталь: | Scale: Left: B: NA: Assy |
| Парткод: | D120 1787 |
| Деталь: | Photointerruptor: Flat: Pitch 2 mm: M4 |
| Парткод: | AW02 0146 |
| Деталь: | Sensor Shielding Plate |
| Парткод: | G570 1225 |
| Деталь: | Ground Plate: Sensor: Aks |
| Парткод: | D039 1770 |
| Деталь: | Harness: Scanner: Frame |
| Парткод: | D120 5216 |
| Деталь: | Scale: Inner Back: Printing |
| Парткод: | D120 1791 |
| Деталь: | Exposure Glass |
| Парткод: | A250 1752 |
| Деталь: | Holder: Exposure Glass [TSB002R] |
| Парткод: | D120 1751 |
| Деталь: | Stepped Screw: M3: Scale |
| Парткод: | D120 1759 |
| Деталь: | Photointerruptor: LGRC102 |
| Парткод: | AW02 0204 |
| Деталь: | Cover: Heater: Scanner |
| Парткод: | D039 1823 |
| Деталь: | Seal: Exposure Glass: Rear [TSB002R] |
| Парткод: | B223 1833 |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Screw - M4X12 |
| Парткод: | 0314 0120N |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Tapping Screw: 3x5 |
| Парткод: | 0454 3005Q |
| Деталь: | End Fence: Exit |
| Парткод: | D120 1307 |
| Деталь: | Cover: Paper Exit Sub-unit: Lower: Upper |
| Парткод: | D120 1341 |
| Деталь: | Cover: Paper Exit Sub-unit: Lower |
| Парткод: | D120 1340 |
| Деталь: | Tray: Reverse |
| Парткод: | D120 4818 |
| Деталь: | Frame: Reverse: Upper |
| Парткод: | D120 4821 |
| Деталь: | Frame: Reverse: Lpser |
| Парткод: | D120 4831 |
| Деталь: | Cover: Front: Right Upper |
| Парткод: | D120 1304 |
| Деталь: | Cover: Front: Right Lower |
| Парткод: | D120 1306 |
| Деталь: | Magnet Catch: 44.1N |
| Парткод: | AG07 0504 |
| Деталь: | Cover: Front: Assy |
| Парткод: | D120 1330 |
| Деталь: | Cover: Shield Glass |
| Парткод: | D120 1322 |
| Деталь: | Cover: SD-Card |
| Парткод: | D120 1321 |
| Деталь: | MAGNET CATCH |
| Парткод: | B024 1264 |
| Деталь: | Door: Front |
| Парткод: | D120 1262 |
| Деталь: | Decal: Main Switch: On-standby |
| Парткод: | D011 1252 |
| Деталь: | Decal: Main Switch: On-standby: EU |
| Парткод: | D011 1253 |
| Деталь: | Cover: Main Switch |
| Парткод: | D120 1263 |
| Деталь: | Plate: Logotype: RIC |
| Парткод: | AA00 1564 |
| Деталь: | Plate: Logotype: LAN |
| Парткод: | AA00 1565 |
| Деталь: | Plate: Logotype: SVN |
| Парткод: | AA00 1566 |
| Деталь: | Plate: Logotype: GES |
| Парткод: | AA00 1567 |
| Деталь: | Plate: Logotype: NSA |
| Парткод: | AA00 1568 |
| Деталь: | Plate: Logotype: REX |
| Парткод: | AA00 1569 |
| Деталь: | Plate: Logotype: INF |
| Парткод: | AA00 1570 |
| Деталь: | Hinge - Front Cover |
| Парткод: | G020 1332 |
| Деталь: | Cover: Paper Exit Sub-unit: Behind |
| Парткод: | D120 1343 |
| Деталь: | Decal: Caution: Inkjet |
| Парткод: | D120 6490 |
| Деталь: | Binding Head Tapping Screw: Es: 3x10 |
| Парткод: | 8025318 |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x10 |
| Парткод: | 8025320 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Hexagon Head Tapping Screw: Es: 3x8 |
| Парткод: | 8025319 |
| Деталь: | Power Pack: BCTD |
| Парткод: | AZ32 0176 |
| Деталь: | Bracket: Power Pack |
| Парткод: | D120 5833 |
| Деталь: | Spacer: Lock: KGLS-12RT |
| Парткод: | G020 5871 |
| Деталь: | Receptacle - Transfer/Separation |
| Парткод: | D019 3950 |
| Деталь: | Stand: IOB: Upper |
| Парткод: | D120 5839 |
| Деталь: | Ground Plate: Scanner: Stay: Upper Rear |
| Парткод: | D039 1095 |
| Деталь: | Charge Receptacle |
| Парткод: | D019 3461 |
| Деталь: | Drawer Bracket |
| Парткод: | B238 5891 |
| Деталь: | Stand: IOB: Lower |
| Парткод: | D120 5840 |
| Деталь: | Harness: BCU: Joint Unit |
| Парткод: | D120 5341 |
| Деталь: | Bracket: IOB |
| Парткод: | D120 5838 |
| Деталь: | PCB: BCU: Assy |
| Парткод: | D120 5122 |
| Деталь: | Harness: BCU: ADF |
| Парткод: | D120 5300 |
| Деталь: | Harness: BCU: Image Processing Unit: Power Source |
| Парткод: | D120 5339 |
| Деталь: | Harness: BCU: Main: Lower |
| Парткод: | D120 5330 |
| Деталь: | Harness: BCU: Motor: Main |
| Парткод: | D120 5302 |
| Деталь: | Harness: BCU: Registration Sensor |
| Парткод: | D120 5301 |
| Деталь: | Harness: AC: Fusing: NA |
| Парткод: | D120 5321 |
| Деталь: | Harness: AC: Fusing: EU |
| Парткод: | D120 5322 |
| Деталь: | Harness: BCU: Discharge Lamp |
| Парткод: | D120 5305 |
| Деталь: | Harness: BCU: HVP |
| Парткод: | D120 5317 |
| Деталь: | Harness: BCU: Paper Exit Section: 1bin |
| Парткод: | D120 5306 |
| Деталь: | Harness: HVP: B |
| Парткод: | D120 5343 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | KGPS-12RF |
| Парткод: | 1105 0499 |
| Деталь: | Connector: 51405-1819 |
| Парткод: | 1102 9782 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Connector: 54679-1609 |
| Парткод: | 1102 8501 |
| Деталь: | EEPROM: AT24C64C-PU: 64K |
| Парткод: | 1407 7153 |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0487 |
| Деталь: | KGPS-16RF-V0 |
| Парткод: | 1105 0701 |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0488 |
| Деталь: | Harness Clamp - IWS-2218 |
| Парткод: | 1105 0490 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | CLAMP |
| Парткод: | 1105 0516 |
| Деталь: | Clamp: RSPC-315P |
| Парткод: | 1105 0755 |
Коды ошибок
101
120
121
141
142
144
161-001
161-002
165
195
202
203
204
220
230
231
240
302
355
389
390
391
392
401
402
411
490
500
501
502
503
504
508
530
531
532
541
542
543
544
545
547
551
552
553
554
555
557
559
590
620
621
622
632
633
634
635
636
641
650
651
652
653
669
670
671
672
674
687
690
720
721
723
725
730
731
740
742
746
747
750
760
761
763
764
765
766
770
791
792
793-01, 794-01
793-02, 794-02
793-03, 794-03
793-04, 794-04
793-05, 794-05
793-06, 794-06
793-07, 794-07
793-08, 794-08
793-09, 794-09
793-11, 794-11
793-12, 794-12
798-01
798-02
798-03
798-04
798-05
798-06
798-07
798-08
798-09
816
817
818
819
820
821
822
823
824
826
827
828
829
833
835
838
839
840
841
842
851
853
854
855
857
858
859
860
861
862
863
864
865
866
867
868
870
872
873
874
875
876
877
878
880
881
899
900
901
920
921
925
990
991
992
994
995
997
998
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 141 |
| Display: | SVC 141 ERROR |
| Description: | Motor |
| Causes: | • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor excessive PWM - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board” |
| Error code: | 142 |
| Display: | Contact the Service center. 142: Error |
| Description: | Motor |
| Causes: | • Standard white plate defective, dirty • Moisture inside the scanner unit • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor, over speed - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 161-001 |
| Description: | IPU error The error result of self-diagnostic by the ASIC on the BICU is detected. |
| Causes: | • Defective BICU • Defective connection between BICU and SBU |
| Remedy: | 1. Check the connection between BICU and SBU. 2. Replace the BICU. |
| Error code: | 161-002 |
| Description: | IPU error Detected an error during an access to the Ri. |
| Causes: | • Defective BICU board |
| Remedy: | Replace the BICU board. |
| Error code: | 165 |
| Description: | Out of Paper; Load Tray 1 (MPT) with [size] [type] The Tray 1 (MPT) No Paper Sensor indicates Tray 1 (MPT) is empty. |
| Causes: | • No Paper Sensor, PL5.3.14 • No Paper Sensor Actuator, PL5.3.15 • FRONT/DUP Harness, PL5.3.28 |
| Remedy: | 1 Fill Tray 1 (MPT) with paper. Does the error persist? Go to Step 2. Complete. 2 Check the following for evidence of fault or damage: • Tray 1 (MPT) No Paper Sensor, PL5.3.14 • Sensor Actuator, PL5.3.15 Is there any damage? Replace any damaged parts. Go to Step 3. 3 Test the Tray 1 (MPT) No Paper Sensor. Run the Service Diagnostics Tray 1 (MPT) No Paper Sensor test. Does the sensor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the Tray 1 (MPT) No Paper Sensor signal. Is there +3.3 V across P/J135-1 <=> P/J135-2? Replace the sensor. Go to Step 5. 5 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J135. 2. Check continuity between J13 <=> J134. Replace the Engine Control Board. Replace the FRONT/DUP Harness. |
| Error code: | 195 |
| Description: | Serial Number Error |
| Causes: | The serial number stored in the memory (EGB) is not correct. |
| Remedy: | EEPROM defective EGB replaced without original EEPROM |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 204 |
| Display: | Power OFF/ON 204:Error |
| Description: | Polygon motor error 3: XSCRDY signal error |
| Causes: | The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing. |
| Remedy: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board). |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 231 |
| Display: | Service Call 231: Error |
| Description: | FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 240 |
| Display: | Service call 240: Error |
| Description: | LD error |
| Causes: | The IPU (EGB) detects a problem at the LD unit. |
| Remedy: | • Worn-out LD • Disconnected or broken harness of the LD. 1. Replace the laser optics unit. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 355 |
| Display: | Set new belt 355: Belt life |
| Description: | Belt life notified (alarm). Print N-count by opening and closing cover. |
| Causes: | Right after replacing belt? |
| Remedy: | Check belt life. Replace belt. |
| Error code: | 389 |
| Display: | Open top cover 389: Paper jam |
| Description: | Jam generated in paper path. |
| Causes: | Open front cover and check jammed paper. |
| Remedy: | Remove jammed paper. |
| Error code: | 390 |
| Display: | Check MP tray 390: Paper jam |
| Description: | Paper jam during paper feed from MT. |
| Causes: | Check for miss-fed paper around MT cassette. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace MT. |
| Error code: | 391 |
| Description: | TD sensor error: Auto adjust error During automatic adjustment of the TD sensor, output voltage was less than 1.8V, or more than 4.8V during TD sensor initial setting |
| Causes: | • TD sensor connector or harness loose, broken, defective • TD sensor defective • IOB defective • Toner supply defective (confirm that the toner seal strip has been removed from toner cartridge) |
| Remedy: | 1. Check the harness or harness connection. 2. Clean the surface of the quenching lamp glass. |
| Error code: | 392 |
| Description: | Development Bias Error The development bias feedback voltage was less than 0.3 V for longer than 200 ms while the PWM duty value was more than 5% (indicating a development bias leak). |
| Causes: | • Bias terminal damaged • High voltage cable damaged, defective • CGB power pack defective |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 411 |
| Display: | SVC 411 ERROR |
| Description: | IRQ timer 1 error |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | Replace the Controller board. |
| Error code: | 490 |
| Display: | Set 490: No paper in MP tray (* stands for A4 B4, etc.) |
| Description: | ITB (Image Transfer Belt) Unit Set Error |
| Causes: | The TM sensor does not detect the reflection from the ITB. |
| Remedy: | • No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S |
| Error code: | 500 |
| Description: | Transport/Fusing Motor Error |
| Causes: | The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the transport/fusing motor. Replace it if necessary. |
| Error code: | 501 |
| Display: | Service Call 501: Error |
| Description: | Tray 1 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503 |
| Display: | Service Call 503: Error |
| Description: | Tray 3 must be rebuilt |
| Causes: | (A model other than D581) Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. (D581) Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 504 |
| Description: | Tray 4 must be rebuilt |
| Causes: | The 2nd tray of D580, 1st tray of D580 when D579 and D580 are attached, the bottom D579 when two units of D579 are attached, or D631 when D581 and D631 are attached. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection D581 when D579 and D581 are attached.Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 508 |
| Description: | Replace black developer |
| Causes: | • HP sensors on the left and right side loose, disconnected, defective • Cutter motor harness damaged, defective • HP sensors defective • Cutter motor defective Note: Paper can be fed from the bypass table if the roll feeder or paper cassette is not operationg. |
| Error code: | 530 |
| Description: | LSU Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the LSU fan motor. |
| Error code: | 531 |
| Description: | Fusing Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the fusing fan motor. |
| Error code: | 532 |
| Description: | IH coil fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH coil fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH coil fan motor • Defective IH coil fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH coil fan. 3. Replace the IOB. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 554 |
| Description: | Fusing sleeve belt overheat: End (hardware error) The fusing sleeve belt thermistor detects 250°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 555 |
| Description: | Fusing Heater error: End The fusing heater keeps full power for 9 seconds or more. |
| Causes: | Defective thermistors. Broken heater cables. |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 590 |
| Description: | Toner collection motor error The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on. |
| Causes: | • Motor lock due to obstruction • Motor driver board defective • Motor connection loose, defective • Toner collection motor sensor disconnected, sensor defective • Rotational transmission shaft (o6 x 30) missing |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 622 |
| Description: | Paper Bank communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The paper bank`s control board is faulty. Defective BCU/IOB. The paper bank`s connection is faulty. |
| Remedy: | • Reconnect the paper bank cables. • Replace the BCU. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 633 |
| Description: | Key/card counter device error 2 During communication with the device, the MCU received a break (Low) signal. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 636 |
| Description: | OSM User Code File Error The correct "usercode" file could not be found in the root folder of the SD card because the file is not present, or the existing file is corrupted or the wrong type file. |
| Causes: | • Make sure the eccm.mod file is in the root folder of the SD card. Note: The usercode files are created with the User Setting Tool "IDissuer.exe". |
| Error code: | 641 |
| Description: | BICU control data transfer abnormal A sampling of the control data sent from the BICU reveals an abnormality. |
| Causes: | • Defective controller board • External noise • Defective BCU |
| Remedy: | 1. Replace the controller board. 2. Replace the BCU. |
| Error code: | 650 |
| Description: | @Remote communication error 1 A dial-up or modem error occurred during @Remote operation. (This error occurs only during @Remote operation.) |
| Causes: | • Modem line disconnected • Modem board missing or not properly installed |
| Error code: | 651 |
| Description: | @Remote communication error 2 An illegal dial-up to the service center was attempted by @Remote. |
| Causes: | • Software bug |
| Error code: | 652 |
| Description: | Remote service ID2 mismatching ID2 for @Remote certification is mismatching between the controller board and NVRAM. Used controller board installed. Used NVRAM installed An unexpected error occurs when the modem (Embedded RCG-M) tries to call the center with a dial up connection. |
| Causes: | If this occurs during the @Remote installation • Check the NVRAM`s validity and serial number, write the common certificate, and then retry the installation. If this occurs after the @Remote installation • Clear the current @Remote setting, check the NVRAM`s validity and serial number, write the common certificate, and then retry the installation. |
| Error code: | 653 |
| Description: | Incorrect remote service ID2 If one of the following applies to the ID2 recorded in the NVRAM: • The character string is not 17 characters long. • Unprintable characters are included. • It contains spaces only. • It is blank. |
| Remedy: | • Replace the NVRAM • Clear the current @Remote setting, write the common certificate, and then retry the installation. |
| Error code: | 669 |
| Description: | EEPROM Error |
| Causes: | An unexpected value exists in the initialization flag of the EEPROM |
| Remedy: | • EEPROM not initialized • Defective EEPROM |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 671 |
| Description: | Engine board mismatch error Engine board and controller mismatch detected. |
| Causes: | • Wrong engine board installed. • Wrong controller board installed. • Check the type of engine board and controller board. |
| Remedy: | 1. Replace the BCU. 2. Replace the controller board. |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 674 |
| Description: | Transmission error in controller board Video transmission error is detected in the controller board. |
| Causes: | Defective Controller Board |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 690 |
| Description: | GAVD Communication Error |
| Causes: | The ID of the GAVD is not identified during initialization. The chip ID of the GAVD cannot be detected by the machine at power-on. |
| Remedy: | • Defective EGB 1. Replace the EGB. EE |
| Error code: | 720 |
| Description: | Fan folder transport motor error A transport motor lock signal was detected for more than 5 sec. while the motor was running. |
| Causes: | • Transport motor harness connector loose, disconnected, broken • Motor overload due to an obstruction • Transport motor defective • Fan folder unit MCU defective |
| Error code: | 721 |
| Description: | Jogger motor error • Jogger HP sensor does not detect the jogger fence for 2000ms after the jogger unit has moved to its home position. • Jogger HP sensor does not turn off 300 ms after the jogger unit has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective jogger HP sensor • Overload on the jogger motor • Defective jogger motor • Defective main board • Disconnected or defective harness |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the jogger HP sensor (if the jogger motor works correctly). 3. Replace the jogger motor (if the jogger motor does not work). 4. Replace the finisher main board. |
| Error code: | 723 |
| Description: | Stack feed-out motor error • Stack feed-out HP sensor does not detect the home position of the stack feedout belt 3000ms after the stack feed-out belt has moved to its home position. • Stack feed-out HP sensor does not turn off 200 ms after the stack feed-out belt has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code |
| Causes: | • Defective stack feed-out HP sensor • Overload on the stack feed-out motor • Defective stack feed-out motor • Defective main board • Disconnected or defective harness |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the stack feed-out HP sensor (if the stack feed-out motor works correctly). 3. Replace the stack feed-out motor (if the stack feed-out motor does not work). 4. Replace the finisher main board. |
| Error code: | 725 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor. 4. Replace the finisher main board. |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 731 |
| Description: | Finisher exit guide motor error After the finisher exit guide motor turned on, the exit guide sensor did not activate within 800 ms. |
| Causes: | • Finisher exit guide motor defective harness or connector loose, broken, defective • Finisher exit guide motor defective • Finisher exit guide sensor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the upper tray exit motor. 4. Replace the finisher main board. |
| Error code: | 740 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished after a certain time. For the 1000-sheet booklet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 742 |
| Description: | Finisher stapler movement motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished for a certain time. For the 1000-sheet booklet finisher • The stapler HP sensor is not activated within the specified time after the stapler motor turned on. (first detection: jam error, consecutive twice detection SC code). |
| Causes: | • Motor overload • Loose connection of the stapler home position sensor • Loose connection of the stapler movement motor • Defective stapler home position sensor • Defective stapler movement motor |
| Remedy: | 1. Check the connection of the stapler movement motor. 2. Check the connection of the stapler home position sensor. 3. Replace the stapler home position sensor. 4. Replace the stapler movement motor. |
| Error code: | 746 |
| Description: | 1000-sheet booklet finisher: Stack feed motor error • The stack feed HP sensor does not detect "ON" twice (once: jam error) for specified time after the stack feed motor has turned on. • The stack feed HP sensor does not detect "OFF" twice (once: jam error) for specified time after the stack feed motor has turned on. |
| Causes: | • Motor overload • Loose connection of the stack feed motor • Defective stack feed motor |
| Remedy: | 1. Check the connections and cables for the stack feed motor and HP sensor. 2. Check for blockages in the stack feed motor mechanism. 3. Replace the stack feed HP sensor and/or stack feed motor 4. Replace the finisher main board. |
| Error code: | 747 |
| Description: | Stack Plate Motor Error 2: Front Motor (B830) The stack plate HP sensor (front) does not activate within 500 ms after the motor turns on. The 1st detection failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | If the motor is operating • Front stack plate HP sensor harness loose, broken, defective • Front stack plate HP sensor defective If the motor is not operating: • Motor blocked by an obstruction • Motor harness loose, broken, defective • Motor defective • Finisher main board defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the stack plate HP sensor (front). 4. Replace the stack plate motor (front). 5. Replace the finisher main board |
| Error code: | 750 |
| Description: | 1000/3000-sheet (booklet) finisher: Tray lift motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. |
| Causes: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor |
| Remedy: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor. |
| Error code: | 760 |
| Description: | Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Punch HP sensor disconnected, defective • Punch motor disconnected or defective • Punch motor overload due to obstruction |
| Remedy: | 1. Check the connections and cables for the punch motor and HP sensor. 2. Check for blockages in the punch motor mechanism. 3. Replace the punch HP sensor and/or punch motor 4. Replace the finisher main board. |
| Error code: | 761 |
| Description: | Finisher folder plate motor error The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Remedy: | 1. Check the connections and cables for the folder plate motor and HP sensor. 2. Check for blockages in the folder plate motor mechanism. 3. Replace the folder plate HP sensor and/or folder plate motor 4. Replace the finisher main board. |
| Error code: | 763 |
| Description: | Rear fold plate HP sensor error The state (on/off, off/on) of the rear fold plate HP sensor in the fan fold unit did not change 1 sec. after the plate started to move. |
| Causes: | • Fold plate motor (R) harness connector loose, disconnected, broken • Rear fold plate HP sensor harness connector loose, disconnected, broken • Fold plate motor (R) defective • Rear fold plate HP sensor defective • Undetected paper is jamming the action of the motor or fold plate • Fan folder unit MCU defective |
| Error code: | 764 |
| Description: | Paper position sensor slide motor error The paper position sensor moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the paper position sensor slide motor. 2. Replace the paper position sensor slide motor. |
| Error code: | 765 |
| Description: | Fold unit bottom fence motor error The bottom fence of the fold unit moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the fold unit bottom fence motor. 2. Defective fold unit bottom fence motor. |
| Error code: | 766 |
| Description: | Stacking sponge roller motor error The sponge roller moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the stacking sponge roller motor. 2. Defective stacking sponge roller motor. |
| Error code: | 770 |
| Description: | Shift motor error The shift motor HP sensor does not detect any change for 1.86 seconds after the shift motor has turned on at power on or during its operation. |
| Causes: | Defective shift motor. Defective shift motor HP sensors. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 791 |
| Description: | Bridge unit error The machine recognizes the finisher, but does not recognize the bridge unit. |
| Causes: | The bridge unit is not installed. Defective bridge unit. Re-install the bridge unit. Turn the main power switch off and on. |
| Remedy: | • Re-install the bridge unit. • Turn the main power switch off and on. |
| Error code: | 792 |
| Description: | Finisher error The machine does not recognize the finisher, but recognizes the bridge unit. |
| Causes: | The finisher`s connection is faulty. The finisher is not attached to a device equipped with the bridge unit. Defective finisher. |
| Remedy: | Reconnect the finisher or bridge unit, and then turn the main power switch off and then back on. |
| Error code: | 793-01, 794-01 |
| Description: | Front jogger motor error 1-bin tray (D586) The machine does not detect a correct signal from the front jogger fence HP sensor while the front jogger motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective front jogger motor • Loosen connection • Motor overload • Defective front jogger fence HP sensor |
| Remedy: | 1. Replace the front jogger fence HP sensor. 2. Replace the front jogger motor. |
| Error code: | 793-02, 794-02 |
| Description: | Rear jogger motor error 1-bin tray (D586) The machine does not detect a correct signal from the rear jogger fence HP sensor while the rear jogger motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective rear jogger motor • Loosen connection • Motor overload • Defective rear jogger fence HP sensor |
| Remedy: | 1. Replace the rear jogger fence HP sensor. 2. Replace the rear jogger motor. |
| Error code: | 793-03, 794-03 |
| Description: | Pick-up roller contact motor error 1-bin tray (D586) The machine does not detect a correct signal from the pick-up roller HP sensor while the pick-up roller contact motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective pick-up roller contact motor • Loosen connection • Motor overload • Defective pick-up roller HP sensor |
| Remedy: | 1. Replace the pick-up roller HP sensor. 2. Replace the pick-up roller contact motor. |
| Error code: | 793-04, 794-04 |
| Description: | Exit guide plate motor error 1-bin tray (D586) The machine does not detect a correct signal from the exit guide plate HP sensor while the exit guide plate motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective exit guide plate motor • Loosen connection • Motor overload • Defective exit guide plate HP sensor |
| Remedy: | 1. Replace the exit guide plate HP sensor. 2. Replace the exit guide plate motor. |
| Error code: | 793-05, 794-05 |
| Description: | Output tray motor error with 1-bin tray (D586) The machine does not detect a correct signal from the stack height detection lever sensor while the output tray motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective output tray motor • Loosen connection • Motor overload • Defective stack height detection lever sensor |
| Remedy: | 1. Replace the stack height detection lever sensor. 2. Replace the output tray motor. |
| Error code: | 793-06, 794-06 |
| Description: | Stack height detection lever motor error with 1-bin tray (D586) The machine does not detect a correct signal from the stack height detection lever HP sensor while the stack height detection lever motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective stack height detection lever motor • Loosen connection • Motor overload • Defective stack height detection lever HP sensor • Defective stack height detection lever sensor |
| Remedy: | 1. Replace the stack height detection lever sensor. 2. Replace the output tray motor. |
| Error code: | 793-07, 794-07 |
| Description: | Punch drive motor error with 1-bin tray (D586) The machine does not detect a correct signal from the punch position sensor while the punch drive motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective punch drive motor • Loosen connection • Motor overload • Defective punch position sensor |
| Remedy: | 1. Replace the punch position sensor . 2. Replace the punch drive motor. |
| Error code: | 793-08, 794-08 |
| Description: | Punch movement motor error with 1-bin tray (D586) The machine does not detect a correct signal from the punch position sensor while the punch movement motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective punch movement motor • Loosen connection • Motor overload • Defective punch position sensor |
| Remedy: | 1. Replace the punch position sensor. 2. Replace the punch movement motor. |
| Error code: | 793-09, 794-09 |
| Description: | Paper position sensor unit motor error with 1-bin tray (D586) The machine does not detect a correct signal from the paper position detection unit HP sensor while paper position sensor unit motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective paper position sensor unit motor • Loosen connection • Motor overload • Defective paper position detection unit HP sensor |
| Remedy: | 1. Replace the paper position detection unit HP sensor. 2. Replace the paper position sensor unit motor. |
| Error code: | 793-11, 794-11 |
| Description: | Stapler unit motor error with 1-bin tray (D586) The machine does not detect a correct signal from the paper position detection unit HP sensor while the stapler unit motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective paper position sensor unit motor • Loosen connection • Motor overload • Defective paper position detection unit HP sensor |
| Remedy: | 1. Replace the paper position detection unit HP sensor. 2. Replace the paper position sensor unit motor. |
| Error code: | 793-12, 794-12 |
| Description: | Shift roller motor error with 1-bin tray (D586) The machine does not detect a correct signal from the shift roller HP sensor while the shift roller motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective paper position sensor unit motor • Loosen connection • Motor overload • Defective shift roller HP sensor |
| Remedy: | 1. Replace the shift roller HP sensor. 2. Replace the paper position sensor unit motor. |
| Error code: | 798-01 |
| Description: | Upper limit switch error (D585) The upper limit switch of the 500-sheet finisher (D585) is pushed due to tray lift error or some problems. |
| Causes: | • Upper limit switch pulled up • Defective upper limit swtich |
| Remedy: | 1. Check the harness. 2. Check for blockage around the upper limit switch. 3. Replace the upper limit switch. |
| Error code: | 798-02 |
| Description: | Finisher jogger motor error (D585) The machine does not detect a correct signal from the front jogger fence HP sensor while the front jogger motor is operating. The 1st failure issues an original jam message, and the 2nd failure issues this SC code. |
| Causes: | • Jogger HP sensor disconnected, defective • Jogger motor disconnected, defective • Jogger motor overloaded due to obstruction • Finisher main board and jogger motor |
| Remedy: | 1. Check or replace the harness. 2. Check for blockages in the jogger motor mechanism. 3. Replace the jogger HP sensor. 4. Replace the jogger motor. 5. Replace the finisher main board. |
| Error code: | 798-03 |
| Description: | Rear fence motor error (D585) The machine does not detect a correct signal from the rear jogger fence HP sensor while the rear jogger motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Rear jogger motor drive is obstructed (jammed paper, paper scraps, etc.) • The rear jogger fence motor harness loose or broken • Rear jogger fence HP sensor dirty, loose, defective • Rear jogger fence motor defective |
| Remedy: | 1. Check or replace the harness. 2. Check for blockages in the rear jogger motor drive mechanism. 3. Replace the rear jogger fence HP sensor. 4. Replace the rear jogger fence motor. |
| Error code: | 798-04 |
| Description: | Stack feed-out motor error (D585) The machine does not detect a correct signal from the stack feed-out HP sensor while the stack feed-out motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective stack feed-out HP sensor • Overload on the stack feed-out motor • Defective stack feed-out motor • Defective main board • Disconnected or defective harness |
| Remedy: | 1. Check or replace the harness. 2. Check for blockages in the stack feed-out mechanism. 3. Replace the stack feed-out HP sensor. 4. Replace the stack feed-out motor. 5. Replace the main board. |
| Error code: | 798-05 |
| Description: | Positioning roller arm motor error (D585) The machine does not detect a correct signal from the positioning roller HP sensor while the positioning roller arm motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Disconnected or defective harness • Overload on the positioning roller arm motor • Defective positioning roller arm motor • Defective positioning roller HP sensor |
| Remedy: | 1. Check or replace the harness. 2. Check for blockages in the positioning roller arm mechanism. 3. Replace the positioning roller arm motor. 4. Replace the positioning roller HP sensor. |
| Error code: | 798-06 |
| Description: | Corner stapler motor error (D585) The machine does not detect a correct signal from the stapler HP sensor while the stapler motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 798-07 |
| Description: | Stapler movement motor error (D585) The machine does not detect a correct signal from the stapler home position sensor while the stapler movement motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor overload • Loose connection of the stapler home position sensor • Loose connection of the stapler movement motor • Defective stapler home position sensor • Defective stapler movement motor |
| Remedy: | 1. Check the connection of the stapler movement motor. 2. Check the connection of the stapler home position sensor. 3. Replace the stapler home position sensor. 4. Replace the stapler movement motor. |
| Error code: | 798-08 |
| Description: | Tray lift motor error (D585) The machine does not detect a correct signal from the paper height sensor while the Tray lift motor is operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor overload • Loose connection of the shift tray motor • Defective shift tray motor |
| Remedy: | 1. Check the connections to the tray lift motor. 2. Replace the tray lift motor. |
| Error code: | 798-09 |
| Description: | Edge depressor solenoid error (D585) Paper height sensor is ON when the edge depressor solenoid switches ON and the edge depressors start lower. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Solenoid harness loose, broken • Solenoid obstructed • Paper height sensor dirty, harness loose, broke • Solenoid defective • Paper height sensor defective |
| Remedy: | 1. Check or replace the solenoid harness. 2. Check for blockages in the stack pressure mechanism. 3. Replace the paper height sensor. |
| Error code: | 816 |
| Display: | SYSTEM HALT (*) 816 : FW/FROM WRC |
| Description: | Energy saving I/O sub-system error |
| Causes: | The energy saving I/O sub-system detects an error. • Defective energy saving I/O sub-system • The energy saving I/O sub-system detects a controller board error (No response) |
| Remedy: | • Turn the main power switch off and on. • Replace the controller board. |
| Error code: | 817 |
| Display: | SYSTEM HALT (*) 817 : FW/SaveArea |
| Description: | Monitor error This is a file detection and electronic file signature check error when the boot loader attempts to read the self-diagnostic module, system kernel, or root system files from the OS Flash ROM, or the items on the SD card in the controller slot are false or corrupted. |
| Causes: | OS Flash ROM data defective. SD card data defective. Change the controller firmware. Use another SD card. |
| Remedy: | • Change the controller firmware. • Use another SD card. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 833 |
| Display: | SYSTEM HALT (*) 833 : FW/PRN MDL |
| Description: | Self-diagnostic error 8: Engine I/F ASIC |
| Causes: | [0F30] [0F31] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. [0F41] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. |
| Error code: | 835 |
| Display: | SYSTEM HALT (*) 835 : FW/PRN MDL |
| Description: | Self-diagnostic error: Centronic device |
| Causes: | [1102] Loopback connector is connected but check results in an error. • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [110C] Loopback connector is connected but check results in an error. • ASIC device error • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [1120] Centronic loopback connector is not connected for detailed self-diagnostic test. • Centronic loopback connector not connected correctly • Centronic loopback connector defective • ASIC device defective Replace the controller board. |
| Error code: | 838 |
| Display: | SYSTEM HALT (*) 838 : FW/SV MDL |
| Description: | Self-diagnostic Error 10: Clock Generator A verify error occurred when setting data was read from the clock generator via the I2C bus. |
| Causes: | • Replace the controller board |
| Error code: | 839 |
| Display: | SYSTEM HALT (*) 839 : FW/PRN MDL |
| Description: | Serial Flash A read/write operation on the Software Status Register failed. |
| Causes: | • Replace the controller board |
| Error code: | 840 |
| Description: | EEPROM access error During the I/O processing, reading error is occurred. The 3rd reading failure issues this SC code. During the I/O processing, writing error is occurred. |
| Causes: | Defective EEPROM |
| Error code: | 841 |
| Description: | EEPROM read error Mirrored data of the EEPROM is different from the original data in EEPROM. |
| Causes: | Data in the EEPROM is overwritten for some reason. |
| Error code: | 842 |
| Description: | Service Scanner |
| Causes: | This error indicates that a scanner communications failure. |
| Remedy: | 1 Scanner control card to flatbed inteconnect card cable Check for correct installation of the scan control to flatbed interconnect card cable. 2 Motor drive card to flatbed interconnect card cable Check for correct installation of the motor driver card to flatbed interconnect card cable. 3 Motor driver card Flatbed interconnect card If the cables are good and are properly connected, replace the following FRUs in the order shown: • Flatbed interconnect card assembly • Motor driver card assembly |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 858 |
| Description: | Data encryption conversion error (1) |
| Causes: | -01 A serious error has occurred during the data conversion performed for updating the key for data encryption. • The data in the USB flash drive is damaged. • A communication error has occurred due to electromagnetic waves or other noise. • Replace the controller board. * However, if it is "-30", the machine may recover by turning the main power switch off and then back on. -02 A Data encryption conversion error (2) A serious error occurs when data is encrypted to update an encryption key. Defective NVRAM Replace the controller board. -30 A Data encryption conversion error (3) A recoverable error has occurred before starting data conversion. Defective NVRAM • Turn the main switch off and on. • If the error reoccurs, replace the controller board. -31 A A serious error occurs while the data is encrypted. Same as SC991 Same as SC991 |
| Error code: | 859 |
| Description: | HDD data encryption error |
| Causes: | -01 B HDD check error • Hard disk data conversion has been selected, but the hard disk is not installed. • The hard disk is not mounted properly. • No HDD installed • Hard disk formatting is not completed. • The encryption key on the board and the actual encryption key in the hard disk do not match. • Install the HDD correctly. • Initialize the HDD with SP5-832-001. -02 B Power failure during data encryption. The data conversion in the NVRAM or hard disk has not completed successfully. Power interruption has occurred during the conversion of the data in the NVRAM or hard disk Initialize the HDD with SP5-832-001. -10 B Data Read/Write command error Due to time-out, serial communication error, or other problems in DMAC, an irregular DMAC return value has occurred consecutively two or more times Noise or other problems in the SATA connection Same as SC863 |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 862 |
| Description: | Bad sector number error The number of bad sectors in the HDD (image data area) goes over 101. |
| Causes: | • Defective HDD |
| Remedy: | Format the HDD with SP5832-001. Replace the HDD. |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 877 |
| Description: | HDD Data Erase Error The Data Overwrite Security option cannot scramble and erase data on the HDD because the DOS SD card has been corrupted or has |
| Causes: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not been removed from the SD card slot. |
| Remedy: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not solve the problem, the SD card has been damaged.) • Install a new NVRAM • Install a new Data Overwrite Security option with a new SD card |
| Error code: | 878 |
| Description: | TPM electronic recognition error |
| Causes: | -00 The system firmware is not authenticated by TPM. The system hash value registered in the TPM at the machine`s system startup does not match that registered in the USB flash drive. • The system module was updated without going through the formal update process. • Incorrect operating of the USB flash. Replace the board. -01 D USB Flash error An error has occurred in the file system in the USB flash drive. The file system of the USB flash drive is damaged. Replace the controller board. -02 D TPM error An error has occurred in the TPM or TPM driver. Defective TPM Replace the controller board. -03 D TCSD error An error has occurred in the TPM software stack. • The TPM software stack cannot be launched. • The file required for the TPM software stack is missing. Replace the controller board. |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 881 |
| Description: | Management area error Defective software has been detected. |
| Causes: | Abnormal accumulation of authentication information in the software |
| Remedy: | Turn the main switch off and on. |
| Error code: | 899 |
| Display: | Power OFF/ON Error : 899 |
| Description: | Software error A software error occurred in the GW controller. |
| Causes: | • Cycle the machine off/on • Update controller firmware • Controller board defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 994 |
| Display: | Service Call 994:Error |
| Description: | Density Sensor Error |
| Causes: | • No action required because this SC does not interfere with operation of the machine. |
| Remedy: | 1 Is the front door fully closed? Go to step 2. Close the front door. 2 Is the density sensor actuator stuck in place? Release the density sensor actuator. Go to step 3. 3 Are connectors CN406 and CN407 on the sensor board connected properly? Go to step 4. Plug the connector in securely. 4 Is connector CN15 on the printer controller board connected properly? Replace the density sensor. Go to step 5. Plug the connector in securely. 5 Did replacing the density sensor fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 995 |
| Description: | Finisher Main Feed Motor abnormal |
| Causes: | -01 D • Defective BCU • NVRAM Replacement error • Install the previous NVRAM • Input the serial number with SP5-811-004, and turn the main power switch off and on. -02 D • Defective NVRAM • Defective controller Perform SP5-825 to download the appropriate data to the NVRAM, and then turn the main power switch off and then back on. -03 D The serial number cannot be identified due to a mistake during controller replacement or mechanical failure. Replace the controller with the correct type. -04 D - Place all parts in the initial state, and then replace the parts according to the procedures described in the manuals. |
| Remedy: | 1 Is there jammed paper or other obstructions in the paper path? Clear the paper path. Go to step 2. 2 Check to ensure the connector PJ6 on the finisher control board and the feed motor assembly cable are properly connected. Are the cables properly connected? Go to step 3. Properly connect the cables. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pins 7 and 8 and +5 V dc (–10%) between pins 7 and 6 on the feed motor assembly cable connector CN1. Is either voltage missing? Go to step 4. Go to step 5. 4 Disconnect the feed motor assembly cable and PJ6 on the finisher control board. Measure continuity on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 5 Replace the feed motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 6 Measure for +24 V dc between pins 1 and 2 on connector PJ3 on the finisher control board. Measure for +5 V dc between pins 1 and 3 on PJ2 on the finisher control board. Is either voltage missing? Replace the power supply. Replace the finisher control board. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
Название
RICOH TYPE K Скрепки с картриджем
RICOH TYPE K Скрепки (3 упаковки)
RICOH TYPE S Скрепки буклетные в картридже для SR3000
RICOH TYPE T Скрепки в картридже
RICOH TYPE T Скрепки (2 упаковки)
RICOH TYPE 2220D/2320D Тонер-картридж
(889662) RICOH Фотобарабан
RICOH TYPE 28 Девелопер черный
RICOH Узел формирования изображения в сборе
