Ricoh MP402SPF
Рейтинг
Модули
Paper Feed 2
FUSING SECTION 2
DRIVE SECTION 2
Paper Feed 1
ADF Section 3
Manual Feed Section 1
MAIN FRAME SECTION
EXTERIOR
Duplex Section
Transfer
Optical Writing Section
PAPER EXIT SECTION
ADF Section 5
Drive Section 1
Registration Roller
ADF Section 1
ADF Section 4
Fusing Section 1
MANUAL FEED SECTION 2
Optical Reading Section
Electrical Components Section
ADF Section 2
ADF Section 6
Детали ADF Section 3
| Деталь: | PLAIN SHAFT BEARING:MM6 |
| Парткод: | AA082118 |
| Деталь: | PHOTOINTERRUPTOR:LG2A14NL1 |
| Парткод: | AW020198 |
| Деталь: | Compression Spring:Paper Feed |
| Парткод: | M0212816 |
| Деталь: | SPACER:SENSOR:PAPER SIZE SENSOR:MIDDLE |
| Парткод: | M1602636 |
| Деталь: | LEVER:PRESSURE RELEASE:FEED ROLLER |
| Парткод: | M1602803 |
| Деталь: | SHAFT:PRESSURE RELEASE:FEED ROLLER:DIA6 |
| Парткод: | M1602804 |
| Деталь: | SHAFT:ROLLER:PAPER TRAY:DIA6 |
| Парткод: | M1602807 |
| Деталь: | ROLLER:CONNECTING:PAPER TRAY:STAY |
| Парткод: | M1602811 |
| Деталь: | GROUND PLATE:PAPER TRAY:STAY |
| Парткод: | M1602812 |
| Деталь: | GUIDE:COVER:STAY:PAPER TRAY:FRONT |
| Парткод: | M1602813 |
| Деталь: | SHEET:REGISTRATION GUIDE:STAY:UPPER |
| Парткод: | M1602816 |
| Деталь: | DISCHARGE BRUSH:FEED PAPER AGAIN:STAY:REAR |
| Парткод: | M1602819 |
| Деталь: | FEELER:PAPER END SENSOR:PAPER TRAY:STAY |
| Парткод: | M1602822 |
| Деталь: | Roller:Paper Feed:Assy |
| Парткод: | M1602830 |
| Деталь: | PUSH SWITCH:CASSETTE |
| Парткод: | G8003035 |
| Деталь: | BRACKET:SENSOR:PAPER SIZE SENSOR:500 SHEET FEED UNIT |
| Парткод: | M1602581 |
| Деталь: | SPACER:SENSOR:PAPER SIZE SENSOR:OUTER |
| Парткод: | M1602635 |
| Деталь: | GUIDE:TRANSFER:AUXILIARY |
| Парткод: | M1602814 |
| Деталь: | COVER:PSU HARNESS:CONNECTOR:SENSOR BKT |
| Парткод: | M1602582 |
| Деталь: | STAY:PAPER TRAY |
| Парткод: | M1602801 |
| Деталь: | PLAIN SHAFT BEARING:SUPPORT:CONNECTION:ROLLER |
| Парткод: | M1602802 |
| Деталь: | FLAT NUT:FRAME |
| Парткод: | M1604053 |
| Деталь: | PLAIN SHAFT BEARING:MM6 |
| Парткод: | AA082118 |
| Деталь: | Exit Roller:Fusing |
| Парткод: | M1604055 |
| Деталь: | LEVER:ENVELOPE:LEFT |
| Парткод: | M1604057 |
| Деталь: | LEVER:ENVELOPE:RIGHT |
| Парткод: | M1604058 |
| Деталь: | SHAFT:LEVER:ENVELOPE |
| Парткод: | M1604059 |
| Деталь: | Compression Spring:2n |
| Парткод: | M0214619 |
| Деталь: | GUIDE:DUPLEX:FUSING |
| Парткод: | M1604061 |
| Деталь: | PLAIN SHAFT BEARING:MM4 |
| Парткод: | M1604090 |
| Деталь: | DRIVEN ROLLER:DUPLEX |
| Парткод: | M1604091 |
| Деталь: | DISCHARGE BRUSH:PRESSURE ROLLER |
| Парткод: | M1604063 |
| Деталь: | GROUND PLATE:PRESSURE ROLLER |
| Парткод: | M1604064 |
| Деталь: | RADIAL BALL BEARING: DIA6XDIA12X4 |
| Парткод: | AE030083 |
| Деталь: | Lever:Pressure |
| Парткод: | M1604074 |
| Деталь: | TENSION SPRING:PRESSURE ROLLER |
| Парткод: | M1604073 |
| Деталь: | PRESSURE ROLLER:DIA34 |
| Парткод: | M1604096 |
| Деталь: | Fusing Entrance Guide Plate:Lower |
| Парткод: | M1604077 |
| Деталь: | BRACKET:FUSING ENTRANCE GUIDE PLATE:RIGHT |
| Парткод: | M1604079 |
| Деталь: | TORSION SPRING:FUSING ENTRANCE GUIDE PLATE |
| Парткод: | M1604085 |
| Деталь: | GEAR:IDLER:DIA35:FUSING |
| Парткод: | M1604087 |
| Деталь: | GEAR:IDLER:DIA20:FUSING |
| Парткод: | M1604088 |
| Деталь: | GEAR:IDLER:DIA18:FUSING EXIT |
| Парткод: | M1604089 |
| Деталь: | DECAL:BARCODE:FUSING UNIT |
| Парткод: | M0524301 |
| Деталь: | COVER:FUSING:RIGHT |
| Парткод: | M1604172 |
| Деталь: | COIL SPRING:CLEANING ROLLER:PRESSURE ROLLER |
| Парткод: | M1604080 |
| Деталь: | BUSHING:FUSING CLEANING ROLLER:RIGHT |
| Парткод: | M1604083 |
| Деталь: | BUSHING:FUSING CLEANING ROLLER:LEFT |
| Парткод: | M1604084 |
| Деталь: | Cleaning Roller:Assy |
| Парткод: | M1604065 |
| Деталь: | HOUSING:PAPER FEED |
| Парткод: | M1601141 |
| Деталь: | GEAR:PAPER FEED:NO.2 |
| Парткод: | M1601142 |
| Деталь: | GEAR:PAPER FEED:NO.3 |
| Парткод: | M1601143 |
| Деталь: | GEAR:TRANSFER:NO.1 |
| Парткод: | M1601144 |
| Деталь: | GEAR:TRANSFER:NO.2 |
| Парткод: | M1601145 |
| Деталь: | GEAR:MANUAL FEED TABLE:NO.1 |
| Парткод: | M1601146 |
| Деталь: | GEAR:MANUAL FEED:NO.1 |
| Парткод: | M1601147 |
| Деталь: | GEAR:MANUAL FEED:NO.2 |
| Парткод: | M1601148 |
| Деталь: | ELECTROMAGNETIC CLUTCH:TONER SUPPLY |
| Парткод: | M1601149 |
| Деталь: | GEAR:TONER SUPPLY:NO.1 |
| Парткод: | M1601150 |
| Деталь: | GEAR:TONER SUPPLY:NO.2 |
| Парткод: | M1601151 |
| Деталь: | GEAR:TONER SUPPLY:NO.3 |
| Парткод: | M1601152 |
| Деталь: | JOINT:TONER |
| Парткод: | M1601153 |
| Деталь: | GUIDE:JOINT:TONER |
| Парткод: | M1601154 |
| Деталь: | COIL SPRING:TONER SUPPLY |
| Парткод: | M1601155 |
| Деталь: | HOUSINGJOINT :TONER |
| Парткод: | M1601156 |
| Деталь: | SHAFT:TONER SUPPLY |
| Парткод: | M1601157 |
| Деталь: | GUIDE:GEAR:MANUAL FEED TABLE |
| Парткод: | M1601158 |
| Деталь: | BUSHING:TONER SUPPLY:ELECTROMAGNETIC CLUTCH |
| Парткод: | M1601138 |
| Деталь: | Cover:Motor |
| Парткод: | M1601161 |
| Деталь: | ELECTROMAGNETIC CLUTCH:MANUAL FEED |
| Парткод: | M1601182 |
| Деталь: | ELECTROMAGNETIC CLUTCH:MANUAL FEED:TRAY BOTTOM PLATE |
| Парткод: | M1601183 |
| Деталь: | ELECTROMAGNETIC CLUTCH:PAPER FEED |
| Парткод: | M1601184 |
| Деталь: | ELECTROMAGNETIC CLUTCH:REGISTRATION |
| Парткод: | M1601185 |
| Деталь: | ELECTROMAGNETIC CLUTCH:CONNECTING |
| Парткод: | M1601186 |
| Деталь: | Temperature & Humidity Sensor |
| Парткод: | AW140016 |
| Деталь: | PAPER TRAY:REAR:500 SHEET FEED UNITlASSY |
| Парткод: | M1602550 |
| Деталь: | END FENCE:500 SHEET FEED UNIT:ASSY |
| Парткод: | M1602560 |
| Деталь: | COMPRESSION SPRING:PRESSURE:END FENCE |
| Парткод: | GA063082 |
| Деталь: | COMPRESSION SPRING:LOCK:SIDE FENCE |
| Парткод: | M0752610 |
| Деталь: | LEVER:LOCK:END FENCE |
| Парткод: | M1602563 |
| Деталь: | DECAL:OPERATION INSTRUCTIONS:TRAY:REAR |
| Парткод: | M1602572 |
| Деталь: | PAPER TRAY:FRONT:500 SHEET FEED UNIT:SUB-ASSY |
| Парткод: | M1602600 |
| Деталь: | Gear:16z |
| Парткод: | B0902869 |
| Деталь: | SHEET:HOLDER:500 SHEET FEED UNIT:FRONT |
| Парткод: | M1602602 |
| Деталь: | GUIDE:PAPER TRAY:500 SHEET FEED UNIT:FRONT |
| Парткод: | M1602605 |
| Деталь: | INDICATOR:PAPER VOLUME SENSOR:PAPER TRAY:500 SHEET FEED UNIT |
| Парткод: | M1602606 |
| Деталь: | STOPPER:CASSETTE |
| Парткод: | M0212609 |
| Деталь: | HOLDER:FRICTION PAD:ADHESION |
| Парткод: | M1602620 |
| Деталь: | Compression Spring:Separation |
| Парткод: | M1602623 |
| Деталь: | Tray Bottom Plate:Adhesion |
| Парткод: | M1602630 |
| Деталь: | PAD:BASE |
| Парткод: | GF013001 |
| Деталь: | SIDE FENCE:RIGHT:500 SHEET FEED UNIT:ASSY |
| Парткод: | M1602640 |
| Деталь: | LEVER:LOCK:SIDE FENCE:TRAY |
| Парткод: | M1602655 |
| Деталь: | HOLDER:PINION |
| Парткод: | M1602641 |
| Деталь: | SIDE FENCE:LEFT:500 SHEET FEED UNIT:ASSY |
| Парткод: | M1602660 |
| Деталь: | COMPRESSION SPRING:AUXILIARY:SIDE FENCE |
| Парткод: | GA063084 |
| Деталь: | ARM:TRAY BOTTOM PLATE |
| Парткод: | M1602668 |
| Деталь: | DIAL:PAPER SIZE SENSOR:TRAY:EXP:ASSY |
| Парткод: | M1602687 |
| Деталь: | DECAL:DIAL:PAPER SIZE SENSOR:TRAY:EXP |
| Парткод: | M1602682 |
| Деталь: | CUCK:DIAL:PAPER SIZE SENSOR:TRAY |
| Парткод: | M1602683 |
| Деталь: | GRIP:PAPER TRAY |
| Парткод: | M1602631 |
| Деталь: | COVER:TRAY:500 SHEET FEED UNIT:FRONT |
| Парткод: | M1602691 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | M1602693 |
| Деталь: | TIGHTENER:SPRING PLATE:TRAY:ASSY |
| Парткод: | M1602590 |
| Деталь: | TENSION SPRING:TRAY BOTTOM PLATE:500 SHEET FEED UNIT |
| Парткод: | M1602627 |
| Деталь: | SHEET:SPONGE:SIDE FENCE:500TYPE |
| Парткод: | M1602666 |
| Деталь: | SEAL:PAPER TRAY:REAR:EU/AA |
| Парткод: | M1602607 |
| Деталь: | SEAL:PAPER TRAY:REAR:NA |
| Парткод: | M1602608 |
| Деталь: | GEAR:IDLER:LARGE |
| Парткод: | D3DJ4115 |
| Деталь: | GEAR:IDLER:SMALL |
| Парткод: | D3DJ4116 |
| Деталь: | PULLEY:SLOW DOWN:MOTOR |
| Парткод: | D3DJ4117 |
| Деталь: | PULLEY:SLOW DOWN:MIDDLE |
| Парткод: | D3DJ4118 |
| Деталь: | GEAR:IDLER:SHADING |
| Парткод: | D3DJ4119 |
| Деталь: | GEAR:IDLER:MECHANICAL ROLLER CLUTCH:UPPER POSITION |
| Парткод: | D3DJ4122 |
| Деталь: | GEAR:IDLER:MECHANICAL ROLLER CLUTCH:LOWER |
| Парткод: | D3DJ4123 |
| Деталь: | POSITIONING PLATE:DRIVE:MIDDLE |
| Парткод: | D3DJ4312 |
| Деталь: | POSITIONING PLATE:DRIVE:REAR |
| Парткод: | D3DJ4315 |
| Деталь: | POSITIONING PLATE: DRIVE: SHADING |
| Парткод: | D3DJ4316 |
| Деталь: | BELT TENSIONER:PEEN |
| Парткод: | D3DJ4322 |
| Деталь: | PULLEY:IDLER:DIA10 |
| Парткод: | D3DJ4323 |
| Деталь: | TENSION SPRING:TENSION:MIDDLE |
| Парткод: | D3DJ4326 |
| Деталь: | HEXAGON HEAD BOLT:M3X6 |
| Парткод: | D3DJ4327 |
| Деталь: | SYNCHRONOUS BELT:40S1.5M224 |
| Парткод: | D3DJ4331 |
| Деталь: | POSITIONING PLATE:MOTOR |
| Парткод: | D3DJ4334 |
| Деталь: | DC MOTOR:10W:ASSY |
| Парткод: | D3DJ4336 |
| Деталь: | TENSION SPRING:TENSION:MOTOR |
| Парткод: | D3DJ4335 |
| Деталь: | COLLAR:REVERSE |
| Парткод: | D6064124 |
| Деталь: | KEY:BUTTON:MAIN SWITCH |
| Парткод: | M1601084 |
| Деталь: | COIL SPRING:MAIN SWITCH |
| Парткод: | M1601085 |
| Деталь: | LINK:LATCH:DOOR:FRONT |
| Парткод: | M1602712 |
| Деталь: | COIL SPRING:LATCH:DOOR:FRONT |
| Парткод: | M1602713 |
| Деталь: | EXTENSION TRAY:INNER:2 |
| Парткод: | M1602784 |
| Деталь: | COIL SPRING:LATCH:COVER:MANUAL FEED |
| Парткод: | M1602774 |
| Деталь: | HOLDER:COMPRESSION SPRING:EXTENSION TRAY |
| Парткод: | M1602775 |
| Деталь: | BASE:PAPER TRAY:MANUAL FEED |
| Парткод: | M1602715 |
| Деталь: | GUIDE:SIDE FENCE:LEFT:MANUAL FEED |
| Парткод: | M1602721 |
| Деталь: | GUIDE:SIDE FENCE:RIGHT:MANUAL FEED |
| Парткод: | M1602722 |
| Деталь: | GEAR:RACK:SIDE FENCE:MANUAL FEED |
| Парткод: | M1602723 |
| Деталь: | GEAR:PIVOT |
| Парткод: | M1602724 |
| Деталь: | COVER:DOOR:FRONT:MIDDLE |
| Парткод: | M1602710 |
| Деталь: | Cover:Manual Feed |
| Парткод: | M1602711 |
| Деталь: | EXTENSION TRAY:MANUAL FEED |
| Парткод: | M1602773 |
| Деталь: | COVER:EXTENSION TRAY:MANUAL FEED |
| Парткод: | M1602776 |
| Деталь: | COVER:EXTENSION TRAY:MIDDLE |
| Парткод: | M1602791 |
| Деталь: | COVER:STOPPER:EXTENSION TRAY |
| Парткод: | M1602792 |
| Деталь: | COVER:FRONT:UPPER:MF |
| Парткод: | M1602793 |
| Деталь: | DUCT:EXIT:RIGHT:MF |
| Парткод: | M1601035 |
| Деталь: | DECAL:ENVELOPE :LEVER:FUSER |
| Парткод: | M1604248 |
| Деталь: | PICKOFF PAWL:MAIN |
| Парткод: | M1601044 |
| Деталь: | BRACKET:HOLDER:PICKOFFPAWL |
| Парткод: | M1601045 |
| Деталь: | Bracket:Drawer:Fusing |
| Парткод: | M1601080 |
| Деталь: | HOLDER:PICKOFF PAWL:MAIN |
| Парткод: | M1601092 |
| Деталь: | COIL SPRING:HOLDER:PICKOFF PAWL |
| Парткод: | M1601093 |
| Деталь: | COIL SPRING:TIGHTENER:PCU |
| Парткод: | M1601063 |
| Деталь: | TIGHTENER:PCU:RIGHT |
| Парткод: | M1601066 |
| Деталь: | TIGHTENER:PCU:LEFT |
| Парткод: | M1601062 |
| Деталь: | Rubber Foot:H5 |
| Парткод: | AH010009 |
| Деталь: | DUCT:EXIT:LEFT |
| Парткод: | M1601036 |
| Деталь: | DC FAN MOTOR:AIO |
| Парткод: | M0521069 |
| Деталь: | DECAL:H-TEMP WARNING |
| Парткод: | M1601059 |
| Деталь: | BRACKET:CONNECTOR:PAPER BANK |
| Парткод: | M1601091 |
| Деталь: | COVER:DUCT:1:FAN:MF1D |
| Парткод: | M1601097 |
| Деталь: | DC FAN MOTOR:80X25 |
| Парткод: | M1601194 |
| Деталь: | DC FAN MOTOR:60X25 |
| Парткод: | M1601192 |
| Деталь: | DUCT:PCU:MF |
| Парткод: | M1601079 |
| Деталь: | DECAL:DISCHARGE:HIGH TEMPERATURE:WARNING |
| Парткод: | M1601028 |
| Деталь: | DECAL:LEVER:SEPARATOR:TONER CARTRIDGE |
| Парткод: | M1601198 |
| Деталь: | STAY:FRAME:FRONT |
| Парткод: | M1601056 |
| Деталь: | BRACKET:RAM BOARD:PCU |
| Парткод: | M1601078 |
| Деталь: | CONNECTOR:ID_CHIP |
| Парткод: | M1873360 |
| Деталь: | SEAL:STAY:FRAME:REAR:B |
| Парткод: | M1601047 |
| Деталь: | GUIDE:PCU:LEFT LOWER |
| Парткод: | M1601061 |
| Деталь: | GUIDE:TRAY:LEFT |
| Парткод: | M1601067 |
| Деталь: | GUIDE:FUSING:LEFT UPPER |
| Парткод: | M1601071 |
| Деталь: | LEVER:FUSING:LEFT |
| Парткод: | M1601073 |
| Деталь: | GUIDE:FUSING:LEFT LOWER |
| Парткод: | M1601072 |
| Деталь: | COVER:FRAME:TRAY |
| Парткод: | M1601095 |
| Деталь: | GUIDE:FUSING:RIGHT UPPER |
| Парткод: | M1601075 |
| Деталь: | LEVER:FUSING:RIGHT |
| Парткод: | M1601077 |
| Деталь: | GUIDE:FUSING:RIGHT LOWER |
| Парткод: | M1601076 |
| Деталь: | GUIDE:PCU:RIGHT LOWER |
| Парткод: | M1601064 |
| Деталь: | COVER:BANKHOLE:FRONT |
| Парткод: | M1601197 |
| Деталь: | COVER:FRAME:PAPER BANK |
| Парткод: | M1601094 |
| Деталь: | COVER:FRAME:LOWER |
| Парткод: | M1601096 |
| Деталь: | GUIDE:TRAY:RIGHT |
| Парткод: | M1601068 |
| Деталь: | COVER:DUCT:2:FAN:MF1D |
| Парткод: | M1601098 |
| Деталь: | Tapping Screw:M3x33 |
| Парткод: | B2591119 |
| Деталь: | STAY:FRAME:REAR |
| Парткод: | M1611020 |
| Деталь: | COVER:LEFT:MF1.5D |
| Парткод: | M0A01211 |
| Деталь: | COVER:LOUVER |
| Парткод: | M1601225 |
| Деталь: | COVER:RIGHT:MF1.5D |
| Парткод: | M0A01221 |
| Деталь: | FILTER:FAN |
| Парткод: | M0A01250 |
| Деталь: | COVER:BUTTON:DOOR:MF |
| Парткод: | M1601222 |
| Деталь: | COIL SPRING:BUTTON:DOOR:MF |
| Парткод: | M1601223 |
| Деталь: | COVER:DUCT:MF |
| Парткод: | M1601228 |
| Деталь: | COVER:UPPER:MF1.5D |
| Парткод: | M0A01231 |
| Деталь: | GROUND PLATE:BICU:UPPER |
| Парткод: | M0A01241 |
| Деталь: | GROUND PLATE:BICU:LOWER |
| Парткод: | M0A01242 |
| Деталь: | Ground Plate:Operation Sub-unit |
| Парткод: | M0A01243 |
| Деталь: | COVER:UPPER:OPERATION SUB-UNIT:MF1.5D |
| Парткод: | M0A01235 |
| Деталь: | COVER:LOWER:OPERATION SUB-UNIT:MF1.5D |
| Парткод: | M0A01236 |
| Деталь: | BRACKET:SUPPORT:OPERATION SUB-UNIT |
| Парткод: | M0A01245 |
| Деталь: | COVER:MIDDLE REAR:POWER SUPPLY UNIT |
| Парткод: | M1605502 |
| Деталь: | DECAL:ORIGINAL TABLE:ENGLISH |
| Парткод: | D3DJ6032 |
| Деталь: | DECAL:CLEANING:SCANNER:ENGLISH |
| Парткод: | M0A01706 |
| Деталь: | DECAL:NAME PLATE:M0A0 |
| Парткод: | M0A06640 |
| Деталь: | DECAL:CAUTION:TC |
| Парткод: | M1601029 |
| Деталь: | SHEET:LOGO:LAN |
| Парткод: | D1201556 |
| Деталь: | PLATE:LOGO:RIC |
| Парткод: | M0521210 |
| Деталь: | DECAL:EARTH:NE:ABS:EU |
| Парткод: | AA000267 |
| Деталь: | CLEANER:LENS:LED HEAD |
| Парткод: | M1091948 |
| Деталь: | SHEET:LOGO:GES |
| Парткод: | D1201557 |
| Деталь: | SHEET:LOGO |
| Парткод: | D1491553 |
| Деталь: | PLATE:LOGOTYPE:GES:IG |
| Парткод: | AA001527 |
| Деталь: | PLATE:LOGOTYPE:LAN:IG |
| Парткод: | AA001531 |
| Деталь: | SHEET:LOGO:SAV |
| Парткод: | D1201561 |
| Деталь: | POWER SUPPLY CODE: 125V :15A:NA |
| Парткод: | 11500427 |
| Деталь: | Power Supply Code:250V:10A:EU |
| Парткод: | 11500458 |
| Деталь: | MODULER CORD:NA:CORE |
| Парткод: | M1605262 |
| Деталь: | GUIDE:UPPER:DUPLEX UNIT |
| Парткод: | M1604601 |
| Деталь: | FEELER:UPPER:DUPLEX UNIT |
| Парткод: | M1604603 |
| Деталь: | SHAFT:IDLER:UPPER:ASSY |
| Парткод: | M1604605 |
| Деталь: | BUSHING:IDLER:DIA4 |
| Парткод: | M1604607 |
| Деталь: | COIL SPRING:IDLER:DUPLEX UNIT |
| Парткод: | M1604611 |
| Деталь: | SYNCHRONOUS BELT:REAR:DUPLEX UNIT |
| Парткод: | M1604674 |
| Деталь: | PLAIN SHAFT BEARING - 6X10X9MM |
| Парткод: | AA082058 |
| Деталь: | GUIDE:FRONT:DUPLEX UNIT |
| Парткод: | M1604621 |
| Деталь: | GRIP:FRONT:DUPLEX UNIT |
| Парткод: | M1604622 |
| Деталь: | HOOK:FRONT:DUPLEX UNIT |
| Парткод: | M1604623 |
| Деталь: | GROUND PLATE:FRONT:DUPLEX UNIT |
| Парткод: | M1604624 |
| Деталь: | LINK:FRAME:DUPLEX UNIT |
| Парткод: | M1604625 |
| Деталь: | LINK:FRONT:DUPLEX UNIT |
| Парткод: | M1604626 |
| Деталь: | DAMPER:FRONT:DUPLEX UNIT |
| Парткод: | M1604627 |
| Деталь: | SHAFT:FRONT:DUPLEX UNIT |
| Парткод: | M1604631 |
| Деталь: | COMPRESSION SPRING:HOOK:DUPLEX UNIT |
| Парткод: | M1604633 |
| Деталь: | DECAL:HANDLE:DUPLEX UNIT |
| Парткод: | M1604635 |
| Деталь: | GUIDE:REAR:DUPLEX UNIT |
| Парткод: | M1604641 |
| Деталь: | Bushing:DIA6 |
| Парткод: | M1604643 |
| Деталь: | SHAFT:REAR:ASSY |
| Парткод: | M1604644 |
| Деталь: | RUBBER BUSHING: SHAFT: REAR |
| Парткод: | M1604645 |
| Деталь: | PLAIN SHAFT BEARING:MM6 |
| Парткод: | AA082118 |
| Деталь: | GUIDE:MIDDLE:DUPLEX UNIT |
| Парткод: | M1604661 |
| Деталь: | GEAR:DRIVE:DUPLEX UNIT |
| Парткод: | M1604662 |
| Деталь: | GEAR:IDLER:DUPLEX UNIT |
| Парткод: | M1604663 |
| Деталь: | PULLEY:DRIVE:DUPLEX UNIT |
| Парткод: | M1604664 |
| Деталь: | GROUND PLATE:MIDDLE:DUPLEX UNIT |
| Парткод: | M1604666 |
| Деталь: | PULLEY:GEAR:DUPLEX UNIT |
| Парткод: | M1604667 |
| Деталь: | PULLEY:NO.2:DUPLEX UNIT |
| Парткод: | M1604668 |
| Деталь: | SHAFT:MIDDLE:DUPLEX UNIT |
| Парткод: | M1604671 |
| Деталь: | SYNCHRONOUS BELT:FRONT:DUPLEX UNIT |
| Парткод: | M1604672 |
| Деталь: | SYNCHRONOUS BELT:FUSING:DUPLEX UNIT |
| Парткод: | M1604673 |
| Деталь: | COIL SPRING:MIDDLE:DUPLEX UNIT |
| Парткод: | M1604614 |
| Деталь: | PHOTOINTERRUPTOR:LG2A14NL1 |
| Парткод: | AW020198 |
| Деталь: | STAY:TRANSFER |
| Парткод: | M1603870 |
| Деталь: | GUIDE:EXIT:STAY:TRANSFER:2 |
| Парткод: | M1603866 |
| Деталь: | SHEET:GUIDE:REGISTRATION:ENTRANCE:LEFT |
| Парткод: | M1603852 |
| Деталь: | SHEET:GUIDE:REGISTRATION:ENTRANCE:RIGHT |
| Парткод: | M1603853 |
| Деталь: | SPONGE:TRANSFER/SEPARATION UNIT:LEFT |
| Парткод: | M1603877 |
| Деталь: | SPONGE:TRANSFER/SEPARATION UNIT:RIGHT |
| Парткод: | M1603878 |
| Деталь: | BUSHING:TRANSFER ROLLER:LEFT |
| Парткод: | M1603856 |
| Деталь: | BUSHING:TRANSFER ROLLER:RIGHT |
| Парткод: | M1603857 |
| Деталь: | COIL SPRING:TRANSFER ROLLER |
| Парткод: | M1603858 |
| Деталь: | GROUND PLATE:ELECTRODE PLATE:SEPARATION |
| Парткод: | M1603859 |
| Деталь: | Electrode Plate:Separation |
| Парткод: | M1603860 |
| Деталь: | COVER:ELECTRODE PLATE:SEPARATION:2 |
| Парткод: | M1603865 |
| Деталь: | TRANSFER ROLLER:ASSY |
| Парткод: | M1606250 |
| Деталь: | SHEET:TRANSFER UNIT:TONER CATCHPAN |
| Парткод: | M1603879 |
| Деталь: | GUIDE:TRANSFER ROLLER:CUCK:ASSY |
| Парткод: | M1603880 |
| Деталь: | GUIDE:TRANSFER ROLLER:CLICK |
| Парткод: | M1603874 |
| Деталь: | SHEET:GUIDE:TRANSFER ROLLER:CLICK |
| Парткод: | M1603875 |
| Деталь: | OPTICAL WRITING UNIT:ASSY |
| Парткод: | M1601850 |
| Деталь: | LED HEAD:1200DPI:211.3MM |
| Парткод: | M1601900 |
| Деталь: | COIL SPRING:HOLDER:LED |
| Парткод: | M1601901 |
| Деталь: | HOLDER:COIL SPRING:LED |
| Парткод: | M1601902 |
| Деталь: | GROUND PLATE:LED:A:LEFT |
| Парткод: | M1601903 |
| Деталь: | GROUND PLATE:LED:A:RIGHT |
| Парткод: | M1601904 |
| Деталь: | HOLDER:LED:RIGHT |
| Парткод: | M1601906 |
| Деталь: | SPACER:HOLDER:LED |
| Парткод: | M1601916 |
| Деталь: | FRAME:HOLDER:LED:ASSY |
| Парткод: | M1601926 |
| Деталь: | HOLDER:LED:LEFT |
| Парткод: | M1601936 |
| Деталь: | GROUND PLATE:LED:B |
| Парткод: | M1601905 |
| Деталь: | LINK:LED:A:LEFT |
| Парткод: | M1601910 |
| Деталь: | LINK:LED:B:LEFT |
| Парткод: | M1601911 |
| Деталь: | LINK:LED:C:LEFT |
| Парткод: | M1601912 |
| Деталь: | COIL SPRING:LINK:LED:LEFT |
| Парткод: | M1601917 |
| Деталь: | GUIDE:LINK:LED:LEFT |
| Парткод: | M1601918 |
| Деталь: | LINK:LED:A:RIGHT |
| Парткод: | M1601913 |
| Деталь: | LINK:LED:B:RIGHT |
| Парткод: | M1601914 |
| Деталь: | LINK:LED:C:RIGHT |
| Парткод: | M1601915 |
| Деталь: | GUIDE:LINK:LED:RIGHT |
| Парткод: | M1601919 |
| Деталь: | COIL SPRING:UNKLED:RIGHT |
| Парткод: | M1601928 |
| Деталь: | HINGE:LED:ASSY |
| Парткод: | M1601907 |
| Деталь: | PCU:CLICK:SERVICE:EXP |
| Парткод: | M9060118 |
| Деталь: | PLAIN SHAFT BEARING:MM6 |
| Парткод: | AA082118 |
| Деталь: | PHOTOINTERRUPTOR:LG2A14NL1 |
| Парткод: | AW020198 |
| Деталь: | ROLLER:IDLER:EXIT:MF1D |
| Парткод: | M1604457 |
| Деталь: | COIL SPRING:ROLLER:EXIT:MF1D |
| Парткод: | M1604459 |
| Деталь: | GUIDE:GATE |
| Парткод: | M1604460 |
| Деталь: | DECAL:GATE:EXIT |
| Парткод: | M1604461 |
| Деталь: | RING:DECURA:EXIT |
| Парткод: | M1604463 |
| Деталь: | PRESSURE PLATE:FUSING:GUIDE |
| Парткод: | M1604464 |
| Деталь: | FEELER:EXIT |
| Парткод: | M1604465 |
| Деталь: | COIL SPRING:FEELER:EXIT |
| Парткод: | M1604466 |
| Деталь: | COIL SPRING:GUIDE:GATE |
| Парткод: | M1604467 |
| Деталь: | COIL SPRING:PRESSURE PLATE |
| Парткод: | M1604468 |
| Деталь: | SHAFT:ROLLER:EXIT:MF1 D |
| Парткод: | M1604470 |
| Деталь: | PULLEY:ROLLER:EXIT |
| Парткод: | M1604471 |
| Деталь: | GUIDE:UPPER:EXIT |
| Парткод: | M1604480 |
| Деталь: | SPRING PLATE:UPPER:EXIT |
| Парткод: | M1604481 |
| Деталь: | ROLLER:IDLER:EXIT:UPPER |
| Парткод: | M1604482 |
| Деталь: | GUIDE:MIDDLE:EXIT |
| Парткод: | M1604484 |
| Деталь: | FEELER:OVERFLOW:PAPER FEED SENSOR:MF1D |
| Парткод: | M1604486 |
| Деталь: | ANTISTATIC BRUSH:EXIT |
| Парткод: | M1604488 |
| Деталь: | GUIDE:REAR:EXIT |
| Парткод: | M1604491 |
| Деталь: | LEVER:DOOR:EXIT:MF1D |
| Парткод: | M1604493 |
| Деталь: | COIL SPRING:GUIDE:REAR:EXIT |
| Парткод: | M1604497 |
| Деталь: | COIL SPRING:LEVER:DOOR:EXIT |
| Парткод: | M1604498 |
| Деталь: | DC Solenoid:Exit:Assy |
| Парткод: | M1604436 |
| Деталь: | COIL SPRING:DC SOLENOID:GATE |
| Парткод: | M1604479 |
| Деталь: | DC STEPPER MOTOR:EXIT |
| Парткод: | M1604446 |
| Деталь: | SYNCHRONOUS BELT:EXIT |
| Парткод: | M1604447 |
| Деталь: | INNER COVER:EXIT:LEFT:MF1D |
| Парткод: | M1604441 |
| Деталь: | COVER:UPPER:EXIT:MF1D |
| Парткод: | M1604453 |
| Деталь: | REFLECTION PHOTO SENSOR:EXIT |
| Парткод: | GW010007 |
| Деталь: | DECAL:RIGHT:COVER:REAR |
| Парткод: | M1604495 |
| Деталь: | COVER:REAR:MF1D |
| Парткод: | M1604490 |
| Деталь: | SHEET:FIX:SENSOR |
| Парткод: | M0214620 |
| Деталь: | SHEET:OPPOSED:SENSOR |
| Парткод: | M1604483 |
| Деталь: | ROLLER:IDLER:MIDDLE:GUIDE |
| Парткод: | M1604489 |
| Деталь: | BRACKET:REVERSE GUIDE |
| Парткод: | M1604452 |
| Деталь: | STEP SCREW |
| Парткод: | B0394480 |
| Деталь: | DECAL:LEFT:COVER:REAR |
| Парткод: | M1604494 |
| Деталь: | GUIDE PLATE:LOWER:OPEN AND CLOSE:ASSY |
| Парткод: | D3DJ1600 |
| Деталь: | TAPE:PRESSURE PLATE |
| Парткод: | D3DJ1114 |
| Деталь: | SHAFT:SCANNING:EXIT:DRIVEN |
| Парткод: | D3DJ1622 |
| Деталь: | Roller:Exit |
| Парткод: | D3DJ1623 |
| Деталь: | TENSION SPRING:SCANNING:EXIT:DRIVEN |
| Парткод: | D3DJ1624 |
| Деталь: | GUIDE:TRANSPORT:EXIT:LOWER |
| Парткод: | D3DJ1625 |
| Деталь: | SHEET:GUIDE:TRANSPORT:EXIT:LOWER |
| Парткод: | D3DJ1626 |
| Деталь: | SHEET:EXIT:PLATE |
| Парткод: | D3DJ1627 |
| Деталь: | GUIDE:EXIT:ASSY |
| Парткод: | D3DJ1632 |
| Деталь: | ROLLER:ENTRANCE |
| Парткод: | D3DJ1414 |
| Деталь: | SHAFT:EXIT:DRIVEN |
| Парткод: | D3DJ1634 |
| Деталь: | Compression Spring:Exit:Driven |
| Парткод: | D3DJ1636 |
| Деталь: | SHEET:TRAY |
| Парткод: | D3DJ1639 |
| Деталь: | SHEET:SCANNING:BEHIND:PLATE |
| Парткод: | D3DJ1649 |
| Деталь: | GUIDE:REFLECTANCE TARGETS PLATE:BEHIND:ASSY |
| Парткод: | D3DJ1642 |
| Деталь: | SPRING PLATE:GUIDE:BEHIND:PRESS FIT |
| Парткод: | D3DJ1650 |
| Деталь: | PLAIN SHAFT BEARING:GUIDE:BEHIND:FRONT |
| Парткод: | D3DJ1653 |
| Деталь: | PLAIN SHAFT BEARING:GUIDE:BEHIND:INNER BACK |
| Парткод: | D3DJ1654 |
| Деталь: | PLAIN SHAFT BEARING:MM6XMM10X6 |
| Парткод: | AA082101 |
| Деталь: | CAM:MOVE:REFLECTANCE TARGETS PLATE:BEHIND |
| Парткод: | D3DJ1662 |
| Деталь: | SHAFT:CAM:PRESS FIT |
| Парткод: | D3DJ1664 |
| Деталь: | GEAR:ROLLER:SCANNING:BEHIND |
| Парткод: | D5433635 |
| Деталь: | LEVER:GUIDE PLATE:LOWER:OPEN AND CLOSE |
| Парткод: | D3DJ1672 |
| Деталь: | PAWL:GUIDE PLATE:LOWER:OPEN AND CLOSE |
| Парткод: | D3DJ1673 |
| Деталь: | SHAFT:LEVER:GUIDE PLATE:LOWER:OPEN AND CLOSE |
| Парткод: | D3DJ1674 |
| Деталь: | TORSION SPRING:GUIDE PLATE:LOWER:OPEN AND CLOSE |
| Парткод: | D3DJ1676 |
| Деталь: | PIN:GUIDE PLATE:PEEN |
| Парткод: | D3DJ1681 |
| Деталь: | BRACKET:MOTOR:ASSY |
| Парткод: | M1601101 |
| Деталь: | GEAR:MOTOR:DRIVE |
| Парткод: | M0A01105 |
| Деталь: | GEAR:PAPER FEED:NO.1 |
| Парткод: | M1601106 |
| Деталь: | GEAR:DUPLEX:NO.1 |
| Парткод: | M1601107 |
| Деталь: | DC BRUSHLESS MOTOR:MAIN |
| Парткод: | M1601108 |
| Деталь: | MYLAR:BKT:DAMPER |
| Парткод: | M1601173 |
| Деталь: | GEAR:DRUM:NO.2 |
| Парткод: | M1601121 |
| Деталь: | JOINT:DRUM |
| Парткод: | M1601122 |
| Деталь: | COIL SPRING:DRUM |
| Парткод: | M1601123 |
| Деталь: | GEAR:DUPLEX UNIT:NO.2 |
| Парткод: | M1601124 |
| Деталь: | PULLEY:FUSING:NO.1 |
| Парткод: | M1601125 |
| Деталь: | PULLEY:FUSING:NO.2 |
| Парткод: | M1601126 |
| Деталь: | SYNCHRONOUS BELT:FUSING:S3M |
| Парткод: | M1601127 |
| Деталь: | GEAR:FUSING:NO.1 |
| Парткод: | M1601128 |
| Деталь: | GEAR:FUSING:NO.2 |
| Парткод: | M1601129 |
| Деталь: | COIL SPRING:FUSING |
| Парткод: | M1601130 |
| Деталь: | HOLDER:SPLINE:JOINT |
| Парткод: | M1601131 |
| Деталь: | GUIDE:LINK:MAIN |
| Парткод: | M1601135 |
| Деталь: | LINK:MAIN |
| Парткод: | M1601136 |
| Деталь: | COIL SPRING:MAIN |
| Парткод: | M1601137 |
| Деталь: | BRACKET:FUSING |
| Парткод: | M1601162 |
| Деталь: | GUIDE:ELECTROMAGNETIC CLUTCH |
| Парткод: | M1601163 |
| Деталь: | ELECTROMAGNETIC CLUTCH:DUPLEX UNIT |
| Парткод: | M1601181 |
| Деталь: | LINK:FRONT |
| Парткод: | M1601139 |
| Деталь: | BKT:DAMPER |
| Парткод: | M1601171 |
| Деталь: | PAD:DAMPER |
| Парткод: | M1601172 |
| Деталь: | ROLLER TERMINAL |
| Парткод: | A1532117 |
| Деталь: | PLAIN SHAFT BEARING:MM8 |
| Парткод: | AA082116 |
| Деталь: | Registration Roller:Driven |
| Парткод: | M1602900 |
| Деталь: | Registration Roller:Drive |
| Парткод: | M1602901 |
| Деталь: | GROUND PLATE:REGISTRATION ROLLER:DRIVEN |
| Парткод: | M1602902 |
| Деталь: | LEVER:PRESSURE:REGISTRATION ROLLER:RIGHT |
| Парткод: | M1602903 |
| Деталь: | LEVER:PRESSURE:REGISTRATION ROLLER:LEFT |
| Парткод: | M1602904 |
| Деталь: | COIL SPRING:REGISTRATION ROLLER:PRESSURE:LEVER |
| Парткод: | M1602905 |
| Деталь: | GUIDE:REGISTRATION ROLLER:UPPER |
| Парткод: | M1602906 |
| Деталь: | DECAL:REGISTRATION:GUIDE:LEFT UPPER |
| Парткод: | M1602907 |
| Деталь: | DECAL:REGISTRATION ROLLER:GUIDE:UPPER |
| Парткод: | M1602908 |
| Деталь: | COVE R :REGISTRATION ROLLER:GUIDE:UPPER |
| Парткод: | M1602909 |
| Деталь: | SEAL:CLEANER:REGISTRATION:LEFT |
| Парткод: | M1602922 |
| Деталь: | SEAL:CLEANER:REGISTRATION:RIGHT |
| Парткод: | M1602923 |
| Деталь: | SHEET:REGISTRATION ROLLER:HOLDER:SENSOR |
| Парткод: | M1602917 |
| Деталь: | CAP:REGISTRATION ROLLER:LEVER:RIGHT |
| Парткод: | M1602919 |
| Деталь: | SHEET:REGISTRATION:DUPLEX:ENTRANCE:RIGHT |
| Парткод: | M1602924 |
| Деталь: | SHEET:REGISTRATION:DUPLEX:ENTRANCE:LEFT |
| Парткод: | M1602925 |
| Деталь: | STUD:BRACKET:REGISTRATION:LEFT:ASSY |
| Парткод: | M1602929 |
| Деталь: | REFLECTION PHOTO SENSOR:EXIT |
| Парткод: | GW010007 |
| Деталь: | TORSION SPRING:REGISTRATION:GUIDE RIHGT |
| Парткод: | M1602912 |
| Деталь: | Paper Feed Unit:Assy |
| Парткод: | D3DJ2200 |
| Деталь: | PLAIN SHAFT BEARING:MM6XMM10X6 |
| Парткод: | AA082101 |
| Деталь: | SPACER:DIA6 |
| Парткод: | AA132208 |
| Деталь: | Collar:Pickup |
| Парткод: | B8722529 |
| Деталь: | SHAFT:PAPER FEED UNIT:ASSY |
| Парткод: | D3DJ2101 |
| Деталь: | FEED ROLLER |
| Парткод: | D3DJ2111 |
| Деталь: | GEAR:FEED |
| Парткод: | D3DJ2116 |
| Деталь: | PAPER STOPPER |
| Парткод: | D3DJ2120 |
| Деталь: | pickup roller |
| Парткод: | D6062113 |
| Деталь: | Shaft:Pickup |
| Парткод: | D6062114 |
| Деталь: | TORQUE LIMITER MECHANICAL CLUTCH:FEED |
| Парткод: | D6062115 |
| Деталь: | GEAR:IDLER:FEED |
| Парткод: | D6062117 |
| Деталь: | GEAR:PICKUP |
| Парткод: | D6062118 |
| Деталь: | ARM:PAPER STOPPER |
| Парткод: | D6062119 |
| Деталь: | LINK:PAPER STOPPER |
| Парткод: | D6062121 |
| Деталь: | HOLDER:PICKUP ROLLER |
| Парткод: | D6062122 |
| Деталь: | COMPRESSION SPRING:PAPER FEED UNIT |
| Парткод: | M3642124 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA143788 |
| Деталь: | PLAIN SHAFT BEARING:MM4:VERTICAL TRANSPORT |
| Парткод: | AA080249 |
| Деталь: | PHOTOINTERRUPTOR:GP1A173LCSVF |
| Парткод: | AW020224 |
| Деталь: | SHAFT:LEVER:COVER:PAPER FEED |
| Парткод: | D3DJ4512 |
| Деталь: | TORSION SPRING:COVER:PAPER FEED:INNER BACK |
| Парткод: | D3DJ4515 |
| Деталь: | COMPRESSION SPRING:DRIVEN ROLLER:PULL OUT |
| Парткод: | D3DJ4518 |
| Деталь: | Feeler:Original Sensor |
| Парткод: | D3DJ4519 |
| Деталь: | SEAL:COVER:PAPER FEED |
| Парткод: | D3DJ4520 |
| Деталь: | COVER:PAPER FEED:MIDDLE |
| Парткод: | D3DJ4522 |
| Деталь: | SPACER:COVER:PAPER FEED:MIDDLE |
| Парткод: | D3DJ4523 |
| Деталь: | Roller:Pull Out |
| Парткод: | D3DJ4525 |
| Деталь: | CUSHION:FEELER:FEED:REAR |
| Парткод: | D3DJ4527 |
| Деталь: | FEELER:FEED:REAR:ASSY |
| Парткод: | D3DJ4530 |
| Деталь: | Cover:Paper Feed |
| Парткод: | D3DJ4541 |
| Деталь: | LEVER:COVER:PAPER FEED |
| Парткод: | D3DJ4542 |
| Деталь: | SHAFT:ROLLER:PULL OUT |
| Парткод: | D6064516 |
| Деталь: | Side Fence:Inner Back |
| Парткод: | D3DJ4612 |
| Деталь: | Side Fence:Front |
| Парткод: | D3DJ4613 |
| Деталь: | Original Table |
| Парткод: | D3DJ4614 |
| Деталь: | EXTENSION TRAY |
| Парткод: | D3DJ4621 |
| Деталь: | SHEET:ORIGINAL TABLE |
| Парткод: | D3DJ4622 |
| Деталь: | DECAL:ORIGINAL SCALE |
| Парткод: | D3DJ6031 |
| Деталь: | GEAR:SIDE FENCE |
| Парткод: | D6064614 |
| Деталь: | PIN:SIDE FENCE |
| Парткод: | D6064615 |
| Деталь: | DISC:SIDE FENCE |
| Парткод: | D6064616 |
| Деталь: | COIL SPRING:SIDE FENCE:ARDF:12N |
| Парткод: | D6064617 |
| Деталь: | Decal:Side Fence |
| Парткод: | M1604930 |
| Деталь: | Cover:Rear |
| Парткод: | D3DJ4710 |
| Деталь: | CAP:CABLE:IC CARD:NO |
| Парткод: | D3DJ4711 |
| Деталь: | CAP:CABLE:IC CARD:YES |
| Парткод: | D3DJ4712 |
| Деталь: | Cover:Front |
| Парткод: | D3DJ4810 |
| Деталь: | Stopper:Original Table |
| Парткод: | D3DJ4811 |
| Деталь: | BRACKET:STOPPER:ORIGINAL TABLE |
| Парткод: | D3DJ4812 |
| Деталь: | COMPRESSION SPRING:STOPPER:ORIGINAL TABLE |
| Парткод: | D3DJ4813 |
| Деталь: | COVER:FRONT:LEFT UPPER |
| Парткод: | D3DJ4814 |
| Деталь: | FUSING UNIT:NA (NA) |
| Парткод: | M1604017 |
| Деталь: | FUSING UNIT:EU (EU/AA) |
| Парткод: | M1604028 |
| Деталь: | THERMOSTAT:LOWER |
| Парткод: | AW110101 |
| Деталь: | ELECTRODE PLATE:LEFT |
| Парткод: | M1604106 |
| Деталь: | ELECTRODE PLATE:RIGHT |
| Парткод: | M1604107 |
| Деталь: | DECAL:H-TEMP WARNING:SMALL |
| Парткод: | D1204184 |
| Деталь: | GROUND PLATE:HOT ROLLER |
| Парткод: | M1604138 |
| Деталь: | BRACKET:GROUND PLATE:HOT ROLLER |
| Парткод: | M1604140 |
| Деталь: | TENSION SPRING:PICKOFF PAWL |
| Парткод: | M1604114 |
| Деталь: | PICKOFF PAWL:HOT ROLLER |
| Парткод: | M1604113 |
| Деталь: | RADIAL BALL BEARING:35X47X7 |
| Парткод: | M0124055 |
| Деталь: | RETAINING RINGS-C:HOT ROLLER |
| Парткод: | M0124281 |
| Деталь: | Gear:Hot Roller |
| Парткод: | M1604086 |
| Деталь: | Hot Roller:DIA30 |
| Парткод: | M1604119 |
| Деталь: | THERMAL INSULATING BUSHING:HOT ROLLER |
| Парткод: | M1604118 |
| Деталь: | COVER:FUSING:LEFT |
| Парткод: | M1604171 |
| Деталь: | Fusing Entrance Guide Plate:Upper |
| Парткод: | M1604130 |
| Деталь: | SEPARATOR:FUSING |
| Парткод: | M1604126 |
| Деталь: | Bracket:Heater:Left |
| Парткод: | M1604121 |
| Деталь: | Bracket:Heater:Right |
| Парткод: | M1604122 |
| Деталь: | HEATER:820W:227V:EU/AA |
| Парткод: | M1604204 |
| Деталь: | HEATER:820W:117V:NA |
| Парткод: | M1604205 |
| Деталь: | FLAT NUT:THERMISTOR |
| Парткод: | M1604103 |
| Деталь: | Thermistor:Fusing:Assy |
| Парткод: | M1604216 |
| Деталь: | GUIDE PLATE:FUSING EXIT |
| Парткод: | M1604151 |
| Деталь: | EXIT ROLLER:FUSING EXIT |
| Парткод: | M1604154 |
| Деталь: | HOLDER:EXIT ROLLER |
| Парткод: | M1604155 |
| Деталь: | SPRING PLATE:EXIT ROLLER |
| Парткод: | M1604156 |
| Деталь: | SHAFT:EXIT ROLLER:FUSING EXIT |
| Парткод: | M1604159 |
| Деталь: | ROLLER:MIDDLE:FUSING:DIA11 |
| Парткод: | M1604157 |
| Деталь: | ROLLER:MIDDLE:FUSING:DIA11 |
| Парткод: | M1604158 |
| Деталь: | FELT WICK:EARTH:HOT ROLLER |
| Парткод: | M1604133 |
| Деталь: | Thermistor:Fusing |
| Парткод: | M1604102 |
| Деталь: | RESISTOR:1GOHM |
| Парткод: | M1604139 |
| Деталь: | Bracket:Thermistor |
| Парткод: | M1604134 |
| Деталь: | DRAWER:FUSING:EU (EU/AA) |
| Парткод: | M1604211 |
| Деталь: | DRAWER:FUSING:NA (NA) |
| Парткод: | M1604212 |
| Деталь: | CAP:THERMISTOR |
| Парткод: | M1604173 |
| Деталь: | WASHER:DIA10.1:DIA6.0:0.6T |
| Парткод: | M1604141 |
| Деталь: | PLAIN SHAFT BEARING:MM6 |
| Парткод: | AA082118 |
| Деталь: | PHOTOINTERRUPTOR:LG2A14NL1 |
| Парткод: | AW020198 |
| Деталь: | PCB:DCSW |
| Парткод: | D1495686 |
| Деталь: | Bracket:Main Switch |
| Парткод: | M1601082 |
| Деталь: | HOLDER:MAIN SWITCH |
| Парткод: | M1601083 |
| Деталь: | Tray Bottom Plate:Manual Feed:Assy |
| Парткод: | M1602706 |
| Деталь: | LINK:BASE:SILENCER |
| Парткод: | M1602733 |
| Деталь: | GUIDE:LEFT:TRAY BOTTOM PLATE |
| Парткод: | M1602734 |
| Деталь: | GUIDE:RIGHT:TRAY BOTTOM PLATE |
| Парткод: | M1602735 |
| Деталь: | PAD:BASE |
| Парткод: | M1602755 |
| Деталь: | Holder:Friction Pad:Manual Feed:Assy |
| Парткод: | M1602707 |
| Деталь: | GUIDE:STAY:MANUAL FEED |
| Парткод: | M1602730 |
| Деталь: | GUIDE:SUB:STAY:MANUAL FEED |
| Парткод: | M1602731 |
| Деталь: | SHAFT:SILENCER |
| Парткод: | M1602741 |
| Деталь: | CAM:SILENCER:LEFT |
| Парткод: | M1602742 |
| Деталь: | CAM:SILENCER:RIGHT |
| Парткод: | M1602743 |
| Деталь: | SPRING PLATE:HOME POSITION SENSOR:SILENCER |
| Парткод: | M1602744 |
| Деталь: | LINK:FEELER HOME POSITION SENSOR:SILENCER |
| Парткод: | M1602745 |
| Деталь: | COIL SPRING:FEELER:SILENCER |
| Парткод: | M1602746 |
| Деталь: | Ground Plate:Manual Feed |
| Парткод: | M1602747 |
| Деталь: | SHEET:ENTRANCE:MIDDLE:ROLLER |
| Парткод: | M1602751 |
| Деталь: | SHEET:EXIT:STAY:MANUAL FEED |
| Парткод: | M1602752 |
| Деталь: | COIL SPRING:FRICTION PAD |
| Парткод: | M1602754 |
| Деталь: | SHAFT:PICKUP:MANUAL FEED |
| Парткод: | M1602760 |
| Деталь: | GUIDE:UPPER:MANUAL FEED |
| Парткод: | M1602762 |
| Деталь: | LINK:FEELER:PAPER END |
| Парткод: | M1602763 |
| Деталь: | PLAIN SHAFT BEARING:MM4:VERTICAL TRANSPORT |
| Парткод: | AA080249 |
| Деталь: | Roller:Pull Out:Option Tray |
| Парткод: | B0902742 |
| Деталь: | COMPRESSION SPRING:PAPER FEED:MANUAL FEED |
| Парткод: | D1172725 |
| Деталь: | COMPRESSION SPRING:VERTICAL TRANSPORT |
| Парткод: | AA063399 |
| Деталь: | PAPER FEED ROLLER:MANUAL FEED |
| Парткод: | AF031092 |
| Деталь: | MYLAR:CLEANER:MID ROLLER DRIVEN |
| Парткод: | M1602737 |
| Деталь: | STEP SCREW |
| Парткод: | B0394480 |
| Деталь: | SEAL:TRAY BOTTOM PLATE:MANUAL FEED:SIDE |
| Парткод: | M1602788 |
| Деталь: | GROUND PLATE:MAIN SWITCH |
| Парткод: | M1602795 |
| Деталь: | CARRIAGE:SCANNER:ASSY |
| Парткод: | M0A01651 |
| Деталь: | PHOTOINTERRUPTOR:GP1A173LCSVF |
| Парткод: | AW020224 |
| Деталь: | DECAL:CLEANING:DOCUMENT FEEDER |
| Парткод: | D3DJ6035 |
| Деталь: | DC STEPPER MOTOR:NMB |
| Парткод: | AX040272 |
| Деталь: | Bracket:Motor:Peen |
| Парткод: | D1171801 |
| Деталь: | CAP:TIMING PULLEY |
| Парткод: | D1171804 |
| Деталь: | GEAR:TIMING PULLEY:81-18:MITSUBOSHI |
| Парткод: | D1171805 |
| Деталь: | Pulley:Idler |
| Парткод: | D1171806 |
| Деталь: | BRACKET:IDLER: PEEN |
| Парткод: | D1171807 |
| Деталь: | BUSHING: BRACKET |
| Парткод: | D1171820 |
| Деталь: | GEAR:SLOW DOWN:53-19 |
| Парткод: | D1171826 |
| Деталь: | COIL SPRING:TENSION |
| Парткод: | D1171837 |
| Деталь: | SYNCHRONOUS BELT:S2M:441 |
| Парткод: | D1171810 |
| Деталь: | Cover:Scanner:Rear Upper |
| Парткод: | M0A01746 |
| Деталь: | COVER:SCANNER:FRONT:ASSY |
| Парткод: | M0A01840 |
| Деталь: | Decal:Scale:Left:NA |
| Парткод: | M0A01710 |
| Деталь: | Decal:Scale:Left:EU |
| Парткод: | M0A01718 |
| Деталь: | DECAL:CAUTION:ORIGINAL:ENGLISH |
| Парткод: | M0A01704 |
| Деталь: | ORIGINAL TRAY:SCANNER:NA:ASSY |
| Парткод: | M0A01657 |
| Деталь: | ORIGINAL TRAY:SCANNER:EU:ASSY |
| Парткод: | M0A01667 |
| Деталь: | Cover:Scanner:Rear |
| Парткод: | M0A01745 |
| Деталь: | PCB:CNB |
| Парткод: | M0A05928 |
| Деталь: | PCB:DCSW |
| Парткод: | D1775686 |
| Деталь: | PCB:BICU:GIM-MF1.5:ASSY |
| Парткод: | M0A05012 |
| Деталь: | Speaker:B284 |
| Парткод: | B2845050 |
| Деталь: | PCB:FCU3.8LE:NA:ASSY |
| Парткод: | M0A05805 |
| Деталь: | PCB:FCU3.8LE:EU:ASSY |
| Парткод: | M0A05806 |
| Деталь: | SHEET:INSULATION:AUX2 |
| Парткод: | M1605535 |
| Деталь: | SHEET:INSULATION:AUX |
| Парткод: | M1605534 |
| Деталь: | POWER SUPPLY UNIT:GIM-MF1.5:DOM/NA |
| Парткод: | GZ230090 |
| Деталь: | POWER SUPPLY UNIT:GIM-MF1.5:EU/AA |
| Парткод: | GZ230091 |
| Деталь: | POWER PACK:CDVT:GIM |
| Парткод: | AZ320187 |
| Деталь: | SHEET:INSULATION:MF1.5D |
| Парткод: | M0A05533 |
| Деталь: | GROUND PLATE:BICU:LEFT LOWER |
| Парткод: | M1605519 |
| Деталь: | GROUND PLATE:BICU:LEFT MIDDLE |
| Парткод: | M1605518 |
| Деталь: | PCB:CTL:GIM-MF1.5:EXP:SUB-ASSY |
| Парткод: | M0A05802 |
| Деталь: | Knob Screw:M3 |
| Парткод: | G1045141 |
| Деталь: | FLANGED HEXAGONAL HEAD BOLT:HDD UNIT:M3X3 |
| Парткод: | AA143848 |
| Деталь: | Bushing:HDD |
| Парткод: | AA161125 |
| Деталь: | CABLE:HDD:SATA:210 |
| Парткод: | D2415250 |
| Деталь: | CABLE:HDD:SATA:POWER_3P:210 |
| Парткод: | M0A05241 |
| Деталь: | BRACKET:HDD:MF1D |
| Парткод: | M1605513 |
| Деталь: | HDD:320GB:AQUARIUS |
| Парткод: | M4445201 |
| Деталь: | COVER:FRONT:POWER SUPPLY UNIT |
| Парткод: | M1605501 |
| Деталь: | Bracket:Power Supply Unit |
| Парткод: | M1605500 |
| Деталь: | GROUND PLATE:POWER PACK |
| Парткод: | M1605515 |
| Деталь: | Bracket:Power Pack |
| Парткод: | M1605506 |
| Деталь: | CLAMP:TWISTLOCK |
| Парткод: | M1605555 |
| Деталь: | TERMINAL:POWER PACK:ASSY |
| Парткод: | M1605507 |
| Деталь: | COVER:CARD |
| Парткод: | M1605531 |
| Деталь: | Panel:Interface |
| Парткод: | M1605520 |
| Деталь: | SCREW:4X6 |
| Парткод: | AA143592 |
| Деталь: | PCB:SENSOR:TONER END SENSOR |
| Парткод: | M1605120 |
| Деталь: | SEAL:BLOCK LIGHT:SENSOR:TONER END SENSOR |
| Парткод: | M1875881 |
| Деталь: | HARNESS:BICU:KEY CARD |
| Парткод: | M0A05360 |
| Деталь: | TAPE:PRESSURE PLATE |
| Парткод: | D3DJ1114 |
| Деталь: | COVER:CARD READER |
| Парткод: | D3DJ1121 |
| Деталь: | GUIDE:HARNESS:CONTACT POINT |
| Парткод: | D3DJ1141 |
| Деталь: | HOLDER:GUIDE:HARNESS:CONTACT POINT |
| Парткод: | D3DJ1142 |
| Деталь: | SHEET:HOLDER:FLAT CABLE |
| Парткод: | D3DJ1143 |
| Деталь: | SHEET:CUSHION:FLAT CABLE |
| Парткод: | D3DJ1144 |
| Деталь: | HOLDER:DFRB |
| Парткод: | D3DJ1131 |
| Деталь: | Guide Plate:Exit |
| Парткод: | D3DJ1151 |
| Деталь: | DISCHARGE BRUSH:EXIT:SUS |
| Парткод: | D3DJ1152 |
| Деталь: | SHEET:EXIT:ASSY |
| Парткод: | D3DJ1160 |
| Деталь: | SHEET:EXIT |
| Парткод: | D3DJ1162 |
| Деталь: | GUIDE PLATE:SCANNING:FRONT LOWER |
| Парткод: | D3DJ1410 |
| Деталь: | SHEET:SCANNING:FRONT LOWER |
| Парткод: | D3DJ1411 |
| Деталь: | LEVER:DRIVEN:SCANNING |
| Парткод: | D3DJ1413 |
| Деталь: | ROLLER:ENTRANCE |
| Парткод: | D3DJ1414 |
| Деталь: | COMPRESSION SPRING:SCANNING:DRIVEN |
| Парткод: | D3DJ1416 |
| Деталь: | SPRING PLATE:DISCHARGE:SCANNING |
| Парткод: | D3DJ1417 |
| Деталь: | SHAFT:ROLLER:PULL OUT |
| Парткод: | D6064516 |
| Деталь: | HINGE:RIGHT:NON DAMPER:LONG |
| Парткод: | D3DJ1821 |
| Деталь: | HINGE:LEFT:DAMPER:LONG |
| Парткод: | D3DJ1820 |
| Деталь: | PHOTOINTERRUPTOR:GP1A173LCSVF |
| Парткод: | AW020224 |
| Деталь: | SHEET:PRESSURE PLATE:SMALL |
| Парткод: | B6524743 |
| Деталь: | Sheet:Pressure Plate |
| Парткод: | D3DJ4911 |
| Деталь: | CUSHION:PRESSURE PLATE:LARGE |
| Парткод: | D3DJ4912 |
| Деталь: | PLAIN SHAFT BEARING:FEED |
| Парткод: | B8722421 |
| Деталь: | POSITIONING PLATE:DRIVE :FRONT |
| Парткод: | D3DJ4110 |
| Деталь: | SHAFT:COUPLING:PEEN |
| Парткод: | D3DJ4111 |
| Деталь: | GEAR:ROLLER:FEED |
| Парткод: | D3DJ4112 |
| Деталь: | GEAR:IDLER:SEPARATION SUB-UNIT |
| Парткод: | D3DJ4113 |
| Деталь: | GEAR:SLOW DOWN:FEED |
| Парткод: | D3DJ4114 |
| Деталь: | Bushing:Feed |
| Парткод: | D3DJ4124 |
| Деталь: | TORQUE LIMITER MECHANICAL CLUTCH:PAPER FEED UNIT |
| Парткод: | D3DJ4127 |
| Деталь: | PIN:GUIDE PLATE |
| Парткод: | D3DJ3821 |
| Деталь: | OPTICAL READING MD:BEHIND:ASSY |
| Парткод: | D3DJ1710 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA143788 |
| Деталь: | GUIDE PLATE:PAPER FEED |
| Парткод: | D3DJ3110 |
| Деталь: | HOLDER:FRICTION PAD |
| Парткод: | D2162002 |
| Деталь: | Friction pad |
| Парткод: | D6063112 |
| Деталь: | Compression Spring:Separation |
| Парткод: | D6063114 |
| Деталь: | SHEET:SEPARATION |
| Парткод: | D6063118 |
| Деталь: | LEVER:PRESSURE RELEASE:SEPARATION |
| Парткод: | D6063116 |
| Деталь: | TENSION SPRING:PRESSURE RELEASE:SEPARATION:4.5N |
| Парткод: | D6063117 |
| Деталь: | CUSHION:SEPARATION |
| Парткод: | D6063119 |
| Деталь: | Pad - Pick-up |
| Парткод: | H5211350 |
| Деталь: | Guide Plate:Transport |
| Парткод: | D3DJ3210 |
| Деталь: | Spring Plate:Guide:Exposure Glass |
| Парткод: | D3DJ3211 |
| Деталь: | SPRING PLATE:DISCHARGE:EXPOSURE GLASS |
| Парткод: | D3DJ3216 |
| Деталь: | GUIDE:HARNESS:TRANSPORT:REAR |
| Парткод: | D3DJ3831 |
| Деталь: | GUIDE:HARNESS:TRANSPORT:FRONT |
| Парткод: | D3DJ3836 |
| Деталь: | REFLECTION PHOTO SENSOR:PS122TL1-A |
| Парткод: | AW010151 |
| Деталь: | ELECTROMAGNETIC CLUTCH:0.35N-M:REVERSE EXIT |
| Парткод: | AX201012 |
| Деталь: | PLAIN SHAFT BEARING:R1 |
| Парткод: | B8722614 |
| Деталь: | TRANSPORT ROLLER:PULL OUT |
| Парткод: | D3DJ3410 |
| Деталь: | GEAR:ROLLER:DIA8 |
| Парткод: | D3DJ4120 |
| Деталь: | GEAR:PULL OUT |
| Парткод: | D3DJ4125 |
| Деталь: | TRANSPORT ROLLER:ENTRANCE |
| Парткод: | D3DJ3510 |
| Деталь: | Transport Roller:Exit |
| Парткод: | D3DJ3610 |
| Деталь: | BUSHING:DIA6:DIA10:9 |
| Парткод: | AA082180 |
| Деталь: | Transport Roller:Exit |
| Парткод: | D3DJ3710 |
| Деталь: | GEAR:ROLLER:DIA6 |
| Парткод: | D3DJ4121 |
| Деталь: | GUIDE PLATE:SCANNING:FACE FRONT |
| Парткод: | D3DJ3811 |
Коды ошибок
SC101-01
SC101-02
SC102-00
SC111-01
SC112-00
SC120-00
SC121-00
SC141-00
SC142-00
SC144-00
SC151-00
SC152-00
SC154-00
SC161-20
SC230-00
SC231-00
SC277-00
SC277-10
SC302
SC332-00
SC364-00
SC440-00
SC498-00
SC508-00
SC520-00
SC530-00
SC531-00
SC532-00
SC541-00
SC542-01
SC542-02
SC543-00
SC544-00
SC545-00
SC547-01
SC547-02
SC547-03
SC551-00
SC553-01, SC553-02
SC554-00
SC557-00
SC559-00
SC632-00
SC633-00
SC634-00
SC635-00
SC636-01
SC636-02
SC636-11
SC637-01
SC637-02
SC641-00
SC650-01
SC650-04
SC650-05
SC650-13
SC650-14
SC651-01
SC651-02
SC652-00
SC653-00
SC665-41
SC667-01
SC667-40
SC669
SC670-01, SC670-02
SC672-10 ... SC672-99
SC673-10
SC681
SC682
SC687-00
SC790-00
SC816
SC817-00
SC818-00
SC819-00
SC840-00
SC841-00
SC842-00
SC842-01
SC842-02
SC845-01 ... SC845-05
SC855-01
SC855-02
SC858-00
SC858-01
SC858-02
SC858-30
SC858-31
SC859-00
SC859-01
SC859-02
SC859-10
SC860-00
SC862-00
SC863-01 ... SC863-23
SC864-00
SC864-01 ... SC864-23
SC865-00 ... SC865-23
SC865-50 ... SC865-73
SC866-00
SC867-00, SC867-01, SC867-02
SC868-00
SC868-01
SC869-01
SC869-02
SC870
SC872-00
SC873-00
SC874
SC875
SC877-00
SC878-00
SC878-01
SC878-02
SC878-03
SC878-20
SC880-00
SC899-00
SC900-00
SC990-00
SC991-00
SC992-00
SC997-00
SC998-00
Описание
| Error code: | SC101-01 |
| Description: | CIS Error: Front Side The peak white level is less than the prescribed value. |
| Causes: | • CIS is defective. • MPU is defective. • Power/signal harness is defective. • Scanner unit condensation • CIS is not set properly, or is dirty. • The white plate is not set properly, or is dirty. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Clean the white guide plate. 2. Reset/clean the CIS and white plate in the scanner. 3. Replace the units in the following order: • Original front side CIS • Engine board • PSU/Signal harness |
| Error code: | SC101-02 |
| Description: | Lamp Error (Detecting the lighting error) The white level peak did not reach the prescribed threshold when the white guide plate was scanned. Error detection timing; During the scanner adjustment (detecting the lighting error) at the time of applying power source for scanner (when the main power is turned ON). |
| Causes: | • Condensation in scanner unit • Connector disconnected • Scanner Carriage defective • BiCU defective • Harness defective • White Guide Plate dirty or attachment fault • IOB defective |
| Remedy: | Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Reconnect the connector. Reconnect the following connectors; • Scanner Carriage – BiCU connector • SBU – LEDB connector (SBU side connector on the scanner carriage) • BiCU – IOB harness 2. Check the white guide plate (exposure glass). Check the white guide plate attached to the exposure glass. If the white guide plate is in an unusual state, replace the white guide plate. 3. Scanner carriage defective Replace the scanner carriage. 4. BiCU defective Replace the BiCU. 5. Harness defective Replace the following harnesses. • Scanner Carriage – BiCU harness • BiCU – IOB harness 6. IOB defective Replace the IOB. |
| Error code: | SC102-00 |
| Description: | LED Illumination Adjustment Error: Front Side The white level peak reached the prescribed threshold when the white plate was scanned after a specified number of adjustments. |
| Causes: | • CIS is defective. • MPU is defective. • Power/signal harness is defective. • Scanner unit condensation • CIS is not set properly, or is dirty. • The white plate is not set properly, or is dirty. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Clean the white guide plate. 2. Reset/clean the CIS and white plate in the scanner. 3. Replace the units in the following order: • Original front side CIS • Controller board • PSU/Signal harness |
| Error code: | SC111-01 |
| Description: | CIS Error: Rear Side The peak white level is less than the prescribed value. |
| Causes: | • CIS is defective. • MPU is defective. • Power/signal harness is defective. • Scanner unit condensation • CIS is not set properly, or is dirty. • The white plate is not set properly, or is dirty. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Reset/clean the CIS and white plate in the document feeder. 2. Replace the units in the following order: • Original rear side CIS • Engine board • PSU/Signal harness |
| Error code: | SC112-00 |
| Description: | LED Illumination Adjustment Error: Rear Side The white level peak reached the prescribed threshold when the white plate was scanned after a specified number of adjustments. |
| Causes: | • CIS is defective. • MPU is defective. • Power/signal harness is defective. • Scanner unit condensation • CIS is not set properly, or is dirty. • The white plate is not set properly, or is dirty. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Reset/clean the CIS and white plate in the document feeder. 2. Replace the units in the following order: • Original rear side CIS • Controller board • PSU/Signal harness |
| Error code: | SC120-00 |
| Description: | Scanner HP Error 1 The scanner HP sensor does not detect the scanner leaving the home position (sensor does not go OFF). |
| Causes: | • MPU is defective. • Power/signal harness is defective. • Scanner unit condensation • CIS is not set properly, or is dirty. • The white plate is not set properly, or is dirty. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Check if there is any foreign object on surface of the scanner HP sensor, or the DF position scanning sensor. 2. Reconnect the harnesses of the scanner HP sensor, or the DF position scanning sensor. 3. Replace the scanner HP sensor, or the DF position scanning sensor. Since it cannot be determined which one is defective from the SC, execute the Input check (SP 5-803-202 DF position scanning sensor) to check the state of the sensor. |
| Error code: | SC121-00 |
| Description: | Scanner HP Error 2 The scanner HP sensor does not detect the scanner leaving the home position (sensor does not go ON). |
| Causes: | • MPU is defective. • Power/signal harness is defective. • Scanner unit condensation • CIS is not set properly, or is dirty. • The white plate is not set properly, or is dirty. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Check if there is any foreign object on surface of the scanner HP sensor, or the DF position scanning sensor. 2. Reconnect the harnesses of the scanner HP sensor, or the DF position scanning sensor. 3. Replace the scanner HP sensor, or the DF position scanning sensor. Since it cannot be determined which one is defective from the SC, execute the Input check (SP 5-803-202 DF position scanning sensor) to check the state of the sensor. |
| Error code: | SC141-00 |
| Description: | Black Level Correction Error: Front Side The automatic adjustment has failed to correct the black level to the permissible range. |
| Causes: | • CIS is defective. • MPU is defective. • Power/signal harness is defective. |
| Remedy: | 1. Clean/reset the connector. 2. Replace the units in the following order: • CIS • Engine board • PSU/Signal harness |
| Error code: | SC142-00 |
| Description: | White Level Correction Error: Front Side The automatic adjustment has failed to correct the white level to the permissible range. |
| Causes: | • CIS is defective. • MPU is defective. • Power/signal harness is defective. • Scanner unit condensation • CIS is not set properly, or is dirty. • The white plate is not set properly, or is dirty. |
| Remedy: | 1. Clean/reset the CIS and white plate. 2. Replace the units in the following order: • CIS • Engine board • PSU/Signal harness |
| Error code: | SC144-00 |
| Description: | Scanner Communication Error: Front Side Cannot correctly establish communication with the MPU(SoC-AFE) |
| Causes: | • Communication error with MPU (SoC-AFE) • PSU is defective. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Clean/reset the connector. 2. Replace the units in the following order: • Engine board • PSU/Signal harness |
| Error code: | SC151-00 |
| Description: | Black Level Correction Error: Rear Side The automatic adjustment has failed to correct the black level (rear side) to the permissible range |
| Causes: | • CIS is defective. • MPU is defective. • Power/signal harness is defective. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Clean/reset the connector. 2. Replace the units in the following order: • CIS • Engine board • PSU/Signal harness |
| Error code: | SC152-00 |
| Description: | White Level Correction Error: Rear Side The automatic adjustment has failed to correct the white level (rear side) to the permissible range. |
| Causes: | • CIS is defective. • MPU is defective. • Power/signal harness is defective. • Scanner unit condensation • CIS is not set properly, or is dirty. • The white plate is not set properly, or is dirty. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Clean/reset the CIS and white plate. 2. Replace the units in the following order: • CIS • Engine board • PSU/Signal harness |
| Error code: | SC154-00 |
| Description: | Scanner Communication Error: Rear Side Cannot correctly establish communication with the MPU (SoC-AFE) |
| Causes: | • Communication error with MPU (SoC-AFE) • PSU is defective. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Clean/reset the connector. 2. Replace the units in the following order: • Engine board • PSU/Signal harness |
| Error code: | SC161-20 |
| Description: | BICU error (DRAM initial error) This error is detected in the DDR-PHY initialization and Training status confirming when the machine is turned on, or returns to full operation from energy save mode. |
| Causes: | • BICU defective • DRAM devise defective |
| Remedy: | • Perform the SC auto rebooting. • Cycle the machine off/on. • Reconnect the connectors. • Replace the harness. • Replace the BICU. |
| Error code: | SC230-00 |
| Description: | FGATE ON Error The FGATE signal did not turn ON within the given time period after the writing process started. |
| Causes: | • GAVD defective • Image processing ASIC defective • BCU, controller board not connected correctly or defective • Harness between BCU and LDB defective |
| Remedy: | • Turn the power off/on. • Replace the harness between IPU and laser unit. • Replace the IPU board. • Replace the controller board. |
| Error code: | SC231-00 |
| Description: | FGATE OFF Error The FGATE signal did not turn OFF within the given time period after the writing process ended. |
| Causes: | • GAVD defective • Image processing ASIC defective • IPU, controller board not connected correctly or defective • Harness between IPU and LDB defective |
| Remedy: | • Turn the power off/on. • Replace the harness between IPU and laser unit. • Replace the IPU board. • Replace the controller board. |
| Error code: | SC277-00 |
| Description: | LED Array communication error: power supply system The power supply to LED Array has been cut off due to a blown fuse or other problem. |
| Causes: | Blown fuse |
| Remedy: | • Check the FFC. • Turn the power OFF and then ON. • Replace the FFC. • Replace the Engine Board. |
| Error code: | SC277-10 |
| Description: | LEDA communication error: other The head type data was read three times in succession |
| Causes: | • Defective engine board (LEDA Power Error: Broken FU7) • Defective harness between PSU – engine board • PSU fault (5V Fuse broken) • Defective controller (Defective engine interface) |
| Remedy: | • Turn the main power off/on. |
| Error code: | SC302 |
| Description: | AC charge output error 3: C An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | This SC is issued if the BICU detects a short in the power pack 10 times consecutively. Open circuit (+) / Short circuit (-) |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC332-00 |
| Description: | Toner supply transfer lock This SC is issued if the error that the toner is not supplied is detected n times consecutively (n: SP2-931-005) on the condition that the toner cartridge is not in end |
| Causes: | • Overload on the toner transferring part (clogging of toner) • Screw for detecting PCDU does not turn • Detector element (sensor) defective: light leak • Supplying pick does not engage • Defective Supplying clutch • Defective Drive mechanism of screw for supplying toner cartridge |
| Remedy: | • Turn the main power off/on. |
| Error code: | SC364-00 |
| Description: | Toner End Sensor output count error When the average value of the toner end sensor output count is 0 n times consecutively (n: SP2-931-003) |
| Causes: | • Connector contact failure/disconnected/broken • Detector element (sensor) does not emit light • Detecting surface inside the developing device is stained |
| Remedy: | • Turn the main power off/on. |
| Error code: | SC440-00 |
| Description: | High Voltage Power Source: Paper Transfer : Output Error The machine detects the error detection signal “L (unexpected)” 10 times for 200 msec consecutively when monitoring the error signal every 20 msec during outputting the PWM signal. |
| Causes: | Hardware error • Input / Output connector is disconnected. • Input / Output harness is short-circuited. • BCU error (signal error) • HVPS defective Load error • Transfer roller`s impedance increases. • Transfer unit is not set properly. |
| Remedy: | • Cycle the main power off/on. • Reconnect or replace the harness of the HVPS (power pack). • Reconnect or replace the harness between the BCU and the HVPS. • Reset or replace the transfer unit. • Check if the contact and separation movement of the transfer unit works correctly. • Replace the HVPS. • Replace the BCU. |
| Error code: | SC498-00 |
| Description: | Temperature and humidity sensor error Temperature sensor output error: Below 0.76V, or above 2.90V, or Moisture sensor output error: more than 2.4V |
| Causes: | • Sensor not setting (disconnection or broken) • Sensor defective |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Check if all connectors related to the Temperature and Humidity Sensor are connected securely. Reconnect the connectors if they are disconnected, or loose. 2. Replace the Temperature and Humidity Sensor. |
| Error code: | SC508-00 |
| Description: | Bypass Tray Size Detection Error The paper size detected on the bypass tray is different from any of the pattern of automatic size detection. |
| Causes: | • Bypass Length Sensor or Bypass Width Sensor malfunction • Bypass Length Sensor or Bypass Width Sensor harness disconnected |
| Remedy: | 1. Replace the Bypass Length Sensor, or Bypass Width Sensor. 2. Replace the harness for Bypass Length Sensor, or Bypass Width Sensor. |
| Error code: | SC520-00 |
| Description: | Main motor error When the main motor is driven, the lock (state of rotation) signal is checked every 100 milliseconds. If the machine detects the lock signal in the High status 20 times in succession, it reports this error. |
| Causes: | • The main motor incurs too much load from a defective unit. • The main motor is defective. |
| Remedy: | • Turn the main power off/on. • Replace the defective unit or the motor. |
| Error code: | SC530-00 |
| Description: | Fusing Exhaust Fan Lock In the motor ON state, the value of the lock sensor is checked every 100msec. If a lock signal is not obtained for 50 times consecutively. |
| Causes: | • Motor defective • Connector disconnected • Harness broken • IOB defective |
| Remedy: | • Replace the fusing exhaust fan. • Reconnect the connector. • Replace the harness. • Replace the Paper Transport IOB. |
| Error code: | SC531-00 |
| Description: | Fusing fan error The fan motor lock (rotating state) signal is sampled 30 times at 100 ms intervals and the fan goes into an unstable rotating state at least ten times. (No error detection occurs for two seconds after the start of the fan or after changing the speed.) |
| Causes: | • Failed fan motor • Disconnected connector |
| Remedy: | • Replace the fan motor. • Check the connector. |
| Error code: | SC532-00 |
| Description: | PSU cooling fan The fan motor lock (rotating state) signal is sampled 30 times at 100 ms intervals and the fan goes into an unstable rotating state at least ten times. (No error detection occurs for two seconds after the start of the fan or after changing the speed.) |
| Causes: | • Failed fan motor • Disconnected connector |
| Remedy: | • Replace the fan motor. • Check the connector. |
| Error code: | SC541-00 |
| Description: | Broken fusing (Center) thermopile wire AD value: 0-6 is detected for specified seconds continuously. Detection period: 500 ms, detection frequency: 10 times or more. |
| Causes: | • Broken thermopile wire • Bad connector contact |
| Remedy: | • Clear the SP: fusing SC. • Replace the connector. • Replace the thermopile. |
| Error code: | SC542-01 |
| Description: | Fusing lamp (Center) thermistor not reloaded 1 The heater thermistor has increased by less than 2.0 degrees in 1.5 seconds 5 times in a row. |
| Causes: | • Deformed or floating thermistor • Input voltage out of range |
| Remedy: | Clear the SP: fusing SC. |
| Error code: | SC542-02 |
| Description: | Fusing lamp (Center) thermopile not reloaded 1 The heater (Center) thermopile does not reach 50 deg C 2.9 seconds after the start of heat control (during normal startup control). |
| Causes: | • Stained thermopile lens • Broken heater wire • Input voltage out of range • The overtemperature prevention mechanism started working |
| Remedy: | • Clean the thermopile lens. • Replace the thermopile. • Replace the Fusing Unit. • Clear the SP: fusing SC. |
| Error code: | SC543-00 |
| Description: | Thermopile (Center) high temperature detection (software) Above 240 degrees C detected for 1 sec. continuously. Detection period 100ms, detection count: 10 times or more. |
| Causes: | • Fusing sleeve belt defective • Paper setting misdetection • Improper paper position in the paper feed tray • Gear abrasion • Thermopile failure • Harness disconnection inside the main machine • Triac defective (short-circuit) • BCU failure • AC controller board failure |
| Remedy: | 1. Inspect the fusing sleeve belt unit, and replace if damaged. 2. Check the paper settings. 3. Check the paper position in the paper feed tray. 4. Reconnect the connectors (between the fusing unit and the BCU). 5. Inspect or replace the gears inside the main machine or fusing unit. 6. Replace the thermopile (center). 7. Replace the harness between the fusing unit and the BCU or the PSU (AC controller board). 8. Replace the BCU. 9. Replace the PSU (AC controller board). If the problem cannot be solved after performing the above steps, replace the fusing unit. |
| Error code: | SC544-00 |
| Description: | Fusing (Center) thermopile high-temperature detected (hardware) The heating (Center) thermistor temperature becomes 250 or higher. (The hardware high-temperature error Sensor flag is detected at 10 ms intervals.) |
| Causes: | • Damaged, shorted triac (element on the PSU) • Failed engine control board • Failed fusing thermopile • Failed fusing thermistor • Abnormal fusing control software behavior |
| Remedy: | • Clear the SP: fusing SC. • Replace the PSU. • Replace the Engine Board. • Replace the fusing thermopile. • Replace the Fusing Unit. |
| Error code: | SC545-00 |
| Description: | Fusing (Center) heater stay ON The fusing (Center) heater stays ON for 3 seconds or more when in stand-by state (or the fusing roller is not rotating). |
| Causes: | • Stained thermopile lens • Broken heater wire • The overtemperature prevention mechanism started working |
| Remedy: | • Clear the SP: fusing SC. • Clean the thermopile lens. • Replace the fusing thermopile. • Replace the Fusing Unit. |
| Error code: | SC547-01 |
| Description: | Zero cross error (relay-contact soldering) Zero-cross signal is detected while the fusing relay is OFF. |
| Causes: | • Fusing relay defective (contact soldering) • Fusing relay drive circuit error |
| Remedy: | 1. Reconnect the connectors between PSU (AC Controller Board) and Paper Transport IOB. 2. Replace the PSU (AC Controller Board). 3. Replace the Paper Transport IOB. |
| Error code: | SC547-02 |
| Description: | Zero cross error (relay contact error) Zero-cross signal is not detected while the fusing relay is ON. |
| Causes: | • Fusing relay damage (contact open) • Fusing relay drive circuit error • PSU fuse (24VS) blowout |
| Remedy: | 1. Reconnect the connectors between PSU (AC Controller Board) and Paper Transport IOB. 2. Replace the PSU (AC Controller Board). 3. Replace the Paper Transport IOB. 4. Replace the harness between PSU (AC Controller Board) and Paper Transport IOB. |
| Error code: | SC547-03 |
| Description: | Zero cross error (low-frequency error) Mains power supply frequency is determined to be 44 Hz or lower. |
| Causes: | Frequency instability of mains power supply |
| Remedy: | 1. Check that the mains power supply frequency is higher than 44 Hz. If it is equal to or lower than 44 Hz, the mains power supply infrastructure may have defects to be dealt with. 2. Replace the PSU (AC Controller Board). |
| Error code: | SC551-00 |
| Description: | Broken fusing (End) thermistor wire AD value: 3F9h-3FFh is detected for specified seconds continuously. Detection period: 500 ms, detection frequency: 10 times or more |
| Causes: | • Broken thermistor wire • Bad connector contact |
| Remedy: | • Clear the SP: fusing SC. • Check the connector connection. • Replace the Fusing Unit. |
| Error code: | SC553-01, SC553-02 |
| Description: | Fusing (End) thermistor high-temperature detected (software) (553-01) In a condition of 235 degrees C or higher temperature, the temperature has increased more than 10 degrees C per 1 second, the heater has continuously reached 100% (maximum) duty, and the center thermistor has detected the failure to reach the target temperature by 11 degrees C. (553-02) The temperature is detected to stay at 250 degrees C or higher for one second. |
| Causes: | • Failed fusing (end) thermistor |
| Remedy: | • Clear the SP: fusing SC. • Replace the fusing (end) thermistor. |
| Error code: | SC554-00 |
| Description: | Fusing (End) thermistor high-temperature detected (hardware) The heating (End) thermistor temperature becomes 250 or higher. (The hardware high-temperature error Sensor flag is detected at 10 ms intervals.) |
| Causes: | • Damaged, shorted triac (element on the PSU) • Failed engine control board • Failed fusing thermopile • Failed fusing thermistor • Abnormal fusing control software behavior |
| Remedy: | • Clear the SP: fusing SC. • Replace the PSU. • Replace the Engine Board. • Replace the fusing thermopile. • Replace the Fusing Unit. |
| Error code: | SC557-00 |
| Description: | Zero Cross Frequency Exceeded In the event of an error |
| Causes: | Frequency instability of mains power supply /Noise |
| Error code: | SC559-00 |
| Description: | Fusing Jam Detected for 3 Times Consecutively Fusing jam (does not reach fusing exit sensor) is detected for 3 times consecutively. • Detection conditions Displays the SC559-00 at the time of integrating the counter each time fusing jam occurs, became fusing jam counter value = 3. The counter value is retained without fusing jam also reset by OFF/ON the power supply. • Control ON/OFF And enables ON / OFF is this SC, the default is set to OFF, then ON at the time of customer requirements. SP1-142-001 0: OFF (default), 1: ON (Set at the time of customer requirements) • Counter reset condition occurs fusing jam 1. Normal paper exit has been done during this continuous fusing jam, fusing jam counter is reset. 2. When "1" is changed to "0" SP1-142-001, to reset the (SP9-912-001) fusing jam counter. 3. When after displaying SC559, SC release is made, reset the (SP9912-001) fusing jam counter. |
| Causes: | • Stripper plate not mounted properly • Gear abrasion • Fusing motor failure |
| Remedy: | 1. Inspect or replace the stripper plate. 2. Replace the gears inside the main machine or fusing unit. 3. Replace the fusing motor. 4. Replace the fusing unit. |
| Error code: | SC632-00 |
| Description: | Counter device error 1 After 3 attempts to send a data frame to the optional counter device via the serial communication line, no ACK signal was received within 100 ms. |
| Causes: | Serial line between the optional counter device, the relay board and copier control board is disconnected or damaged. |
| Remedy: | • Turn the main power off/on. • Check the serial communication line. |
| Error code: | SC633-00 |
| Description: | Counter device error 2 After communication was established, the controller received the brake signal from the accounting device. |
| Causes: | Serial line between the optional counter device, the relay board and copier control board is disconnected or damaged. |
| Remedy: | • Turn the main power off/on. • Check the serial communication line. |
| Error code: | SC634-00 |
| Description: | Counter device error 3 A backup RAM error was returned by the counter device. |
| Causes: | Counter device control board or the backup battery of counter device defective |
| Remedy: | • Replace the counter device control board. • Replace the backup battery. |
| Error code: | SC635-00 |
| Description: | Counter device error 4 A backup battery error was returned by the counter device. |
| Causes: | Counter device control board or the backup battery of counter device defective |
| Remedy: | • Replace the counter device control board. • Replace the backup battery. |
| Error code: | SC636-01 |
| Description: | IC Card Error (Expanded authentication module error) Issued when expanded authentication management is set to "ON" but either of the following occur. • There is no expanded authentication module in the machine. • The SD card or the file of the expanded authentication module is broken. • There is no DESS module in the machine. |
| Causes: | • There is no DESS module in the machine (models on which the function is optional). • There is no expanded authentication module in the machine. • The SD card or the file of the expanded authentication module is broken. |
| Remedy: | • Set a working SD card/expanded authentication module file. • Install the DESS module. • In the SSP mode set SP5-401-160 to "0". • In the SSP mode, set SP5-401-161 to "0". • Replace the NVRAM. |
| Error code: | SC636-02 |
| Description: | IC Card Error (Version error) The version of the expanded authentication module is not correct. |
| Causes: | Incorrect module version |
| Remedy: | Install the correct file of the expanded authentication module. |
| Error code: | SC636-11 |
| Description: | IC Card Error (OSM user code file error) • The correct "usercode" file could not be found in the root folder of the SD card. • The "usercode" file on the SD card could not be read. |
| Causes: | • The "usercode" file does not exist on the SD card. • The "usercode" file on the SD card is an invalid file. • Data in the "usercode" file on the SD card is invalid. • "usercode" file was not moved when moving the application to another SD card |
| Remedy: | Use the user code configuration tool for OSM users (Idissuer.exe) to create the "usercode" and store it in the root folder of the SD card containing the IC card module (eccm.mod). |
| Error code: | SC637-01 |
| Description: | Tracking Information Notification Error (Tracking application error) Tracking information was lost. |
| Causes: | • Tracking SDK application error • Internal notification error |
| Remedy: | Turn the main power off/on. |
| Error code: | SC637-02 |
| Description: | Tracking Information Notification Error (Management server error) Tracking information was lost. |
| Causes: | Communication with tracking management server failed. • Network error • tracking management server error • Tracking SDK application error |
| Remedy: | Turn the main power off/on. |
| Error code: | SC641-00 |
| Description: | Communication error between BCU and Controller board. Controller board does not respond after BCU tries to communicate three times. |
| Causes: | • Controller board software error • Connect error between BCU and Controller board • Engine board software error |
| Remedy: | • Check connections between Controller board and BCU. • Turn the main switch off and on. |
| Error code: | SC650-01 |
| Description: | Remote Service Modem Communication Error (Dialup authentication failure) • An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on. • Displayed only when an error is detected while RC Gate is operating. • SC is not issued if an error occurs during RC Gate installation (because it can be referenced using SP). |
| Causes: | Dialup authentication failure |
| Remedy: | Check the following SPs. • SP5-816-156 • SP5-816-157 |
| Error code: | SC650-04 |
| Description: | Remote Service Modem Communication Error (dialup failing because of incorrect modem configuration) • An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on. • Displayed only when an error is detected while RC Gate is operating. • SC is not issued if an error occurs during RC Gate installation (because it can be referenced using SP). |
| Causes: | Dialup failing because of incorrect modem configuration |
| Remedy: | Check if the setting of SP5-816-160 is correct. If it is correct, then there is a software bug. |
| Error code: | SC650-05 |
| Description: | Remote Service Modem Communication Error (insufficient current or connection error) • An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on. • Displayed only when an error is detected while RC Gate is operating. • SC is not issued if an error occurs during RC Gate installation (because it can be referenced using SP). |
| Causes: | Insufficient current or connection error |
| Remedy: | The line is not supported and nothing can be done. |
| Error code: | SC650-13 |
| Description: | Remote Service Modem Communication Error (RC Gate Type M was installed but modem is not present (detected during operation)) • An error related to communication (dialup connection, modem board etc.) using the RC Gate Type M was detected or an error that prevents RC Gate operation was detected at power on. • Displayed only when an error is detected while RC Gate is operating. • SC is not issued if an error occurs during RC Gate installation (because it can be referenced using SP). |
| Causes: | RC Gate Type M was installed but modem is not present (detected during operation) |
| Remedy: | • If a modem board is not installed, install it. • Check again if the modem driver configurations (SP5-816-160, SP5-816-165 to 171) are correct. • If the problem is not solved, replace the modem. |
| Error code: | SC650-14 |
| Description: | Remote Service Modem Communication Error (RC Gate Type N was installed but modem is present or wired/wireless LAN is not working correctly) • An error related to communication (dialup connection, modem board etc.) using the RC Gate was detected or an error that prevents RC Gate operation was detected at power on. • Displayed only when an error is detected while RC Gate is operating. • SC is not issued if an error occurs during RC Gate installation (because it can be referenced using SP). |
| Causes: | RC Gate Type N was installed but modem is present or wired/wireless LAN is not working correctly |
| Remedy: | • If a modem board is attached, remove it. • Check if wired/wireless LAN works. |
| Error code: | SC651-01 |
| Description: | Illegal Remote Service Dial-up (Chat program parameter error) An unexpected error occurred when RC Gate Type M dialed up the NRS Center. |
| Causes: | Software bug |
| Remedy: | Logging only. |
| Error code: | SC651-02 |
| Description: | Illegal Remote Service Dial-up (Chat program execution error) An unexpected error occurred when RC Gate dialed up the NRS Center. |
| Causes: | Software bug |
| Remedy: | Logging only. |
| Error code: | SC652-00 |
| Description: | Remote service ID2 mismatching There was an authentication mismatch between ID2 for @Remote, the controller board, and NVRAM. |
| Causes: | • Used controller board installed • Used NVRAM installed (such action is not allowed.) |
| Remedy: | • If this occurs during RC Gate installation: Check the validity of the certificate and the NVRAM, check the machine serial number, write the common certificate, and then begin installation again. • If this occurs after RC Gate installation: Clear the RC Gate install status, check the validity of the certificate and the NVRAM, check the machine serial number, write the common certificate, and then begin installation again. |
| Error code: | SC653-00 |
| Description: | Incorrect remote service ID2 |
| Causes: | ID2 stored in the NVRAM has either of the following problems. • Number of characters is not 17. • Includes a character that cannot be printed. • All spaces • NULL |
| Remedy: | Replace the NVRAM. Clear the RC Gate install status, write the common certificate, and then begin installation again |
| Error code: | SC665-41 |
| Description: | Macaron1 Communication Error The machine detects the communication error between CPU and Macaron1 when starting up, or recovery from energy saver mode. |
| Causes: | • FFC connection error • FFC defective (disconnected, foreign object, etc.) • One or more of the following boards may be defective (incorrect or defective components, scraps of solder, etc.): • BCU • IPU |
| Remedy: | 1. Turn the main power OFF/ON. 2. Replace the IPU. 3. Reconnect the FFC between BCU and IPU. 4. Replace the FFC between BCU and IPU. 5. Replace the BCU. |
| Error code: | SC667-01 |
| Description: | Master Device Mode Setting Error The machine detects the CPU mode error when starting up, or recovery from energy saver mode. |
| Causes: | One or more of the following boards may be defective (incorrect or defective components, scraps of solder, etc.): • BCU |
| Remedy: | 1. Turn the main power OFF/ON. 2. Replace the BCU. |
| Error code: | SC667-40 |
| Description: | Macaron1 Mode Setting Error The machine detects the Macaron1 mode error when starting up, or recovery from energy saver mode. |
| Causes: | One or more of the following boards may be defective (incorrect or defective components, scraps of solder, etc.): • BCU • IPU |
| Remedy: | 1. Turn the main power OFF/ON. 2. Replace the IPU. 3. Reconnect the harness between BCU and IPU. 4. Replace the harness between BCU and IPU. 5. Replace the BCU. |
| Error code: | SC669 |
| Description: | EEPROM Communication Error The TD sensor cannot be recovered after retrying N*1 times for EEPROM communication error. (*1 SC669-01 to 26: 3, SC669-36: 2, SC669-37: 1) |
| Causes: | • Electrical noise • EEPROM not connected fully • EEPROM not installed • EEPROM damaged • BCU damaged |
| Remedy: | 1. Turn the main power OFF/ON. 2. Reconnect the EEPROM. 3. Replace the EEPROM. 4. Replace the BCU. |
| Error code: | SC670-01, SC670-02 |
| Description: | SC670-01: Engine Start Up Error SC670-02: Engine Down at Start Up (No SC Reboot) SC670-01 • A /ENGRDY signal was not asserted at power ON or recovery from Energy Save. • There is no response from the EC/PC/SC command within 70 secs after the main power was turned ON. • Writing onto the Rapi driver failed (the other party could not be found through PCI). SC670-02 After a /ENGRDY signal is asserted, there is an unexpected engine down. |
| Causes: | • SC670-01 The engine board failed to start up. • SC670-02 The engine board was reset at an unexpected time. |
| Remedy: | 1. Check if new firmware is available for the engine and controller boards. (SC670-02 only) • If there is new firmware, update the boards. • If there is no new firmware, proceed to the next step. 2. Reconnect the engine board and the controller board. If the SC does not recur, no further action is necessary. If the SC recurs, proceed to the next step. 3. Replace the boards in the following order. • Engine board • Controller board, or the board between the controller and the engine • PSU |
| Error code: | SC672-10 ... SC672-99 |
| Description: | Controller start up error The SC is detected when: • the communication line between the controller and the operation panel cannot be established after power ON, or communication with the controller was cut off even though startup was successful. • no attention code (FDH) or attention acknowledgement code (FEH) was sent from the controller within 30 secs after the power of the operation panel was turned ON or was reset. • the operation panel sends a command to the controller once every 30 secs to check the communication line, and there was no reply from the controller for two consecutive times. • Because this SC is detected by the operation panel, it will not be logged or reported. |
| Causes: | • The controller freezes. • The controller board is not installed correctly. • The controller board is malfunctioning. • The harness of the operation panel is disconnected, or the connection is loose. • The controller’s response is slow. |
| Remedy: | • Turn the main power OFF then ON. • Check if the operation panel harness is properly connected. • Check if the controller board is installed correctly, • Replace the controller board. |
| Error code: | SC673-10 |
| Description: | Operation panel Flair communication error (Smart Operation Panel) This SC is issued only for the machine that has the Smart Operation Panel installed. • Communication between Smart Operation Panel and main machine (this is called "Flair communication") is not sent to Smart Operation Panel. • SP setting (SP5-748-201) for Smart Operation Panel is not activated. |
| Causes: | The CATS module (controller) did not see the response to notification of monitoring service module (operation panel). |
| Remedy: | • Turn the main power OFF/ON. • Set SP5-748-201 (OpePanel Setting: Cheetah Panel Connect Setting) to "1: Connect" if the value is "0: Not connect". |
| Error code: | SC681 |
| Description: | Toner bottle: ID Chip Communication error When error notification was received during communication with the tag and operation is not resumed after N*1 retries. *1 See the detailed table below. |
| Causes: | • Corrupted ID data • Disconnected ID chip • No ID chip • Noise |
| Remedy: | Turn the main power off, and then do the following. 1. Clean ID chip connections inside the toner bottle, and check if any of the ID Chip Contact Board connector pins have snapped. If there are any snapped pins, do step 5. 2. Replace the toner bottle. 3. Reconnect the connectors between Imaging IOB and ID chip contact board. 4. Reconnect the FFC between Imaging IOB and BCU. 5. Replace the ID chip contact board. 6. Reconnect the harness between Imaging IOB and ID chip contact board. 7. Replace the FFC between Imaging IOB and BCU. 8. Replace the Imaging IOB. 9. Replace the BCU. |
| Error code: | SC682 |
| Description: | TD sensor communication error TD sensor cannot be recovered after retrying N*1 times for an ID chip communication error. |
| Causes: | • Corrupted ID data • Disconnected ID chip • No ID chip • Noise |
| Remedy: | Turn the main power off, and then do the following. 1. Reconnect the connectors between Imaging IOB and TD sensor. 2. Reconnect the FFC between Imaging IOB and BCU. 3. Replace the PCDU. 4. Reconnect the harness between Imaging IOB and TD sensor. 5. Replace the FFC between Imaging IOB and BCU. 6. Replace the Imaging IOB. 7. Replace the BCU. • If the last digit of the SC’s branch number (-**) is: 1 or 6, then do the above steps for K 2 or 7, then do the above steps for M 3 or 8, then do the above steps for C 4 or 9, then do the above steps for Y |
| Error code: | SC687-00 |
| Description: | PER Not Received Error Unable to receive the PER command from the controller. |
| Causes: | Communication error |
| Remedy: | Replace the BCU. |
| Error code: | SC790-00 |
| Description: | Maximum number of banks (paper tray units) exceeded error This SC occurs if you stack two or more paper feed units. Only one optional paper feed unit can be installed. |
| Causes: | The number of installed paper tray units exceeds the specifications. |
| Remedy: | Reduce the number of installed paper tray units according to the specifications. |
| Error code: | SC816 |
| Description: | Energy save I/O subsystem error Energy save I/O subsystem detected some abnormality. |
| Causes: | • Energy save I/O subsystem defective • Energy save I/O subsystem detected a controller board error (non-response). • Error was detected during preparation for transition to STR. • SC816-99 occurs as a subsystem error except any error from -06 to 96. |
| Remedy: | Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step. 1. Update the "System" firmware and the other system firmware modules to the latest version. 2. Disable the STR shift function by SP5-191-001 (Power Str Set). 3. Replace the controller board. |
| Error code: | SC817-00 |
| Description: | Monitor error: File detection / Digital signature error • Bootloader cannot read any of diagnostic module, kernel, or root filesystem. • In a bootloader SD card, the digital signature checking for any of diagnostic module, kernel, or root filesystem is failed. |
| Causes: | • Any of the following items does not exist or is broken OS Flash ROM, Diagnostic module in SD card, Kernel, Root filesystem • Any of the following items is revised fraudulently: Diagnostic module in SD card, Kernel, Root filesystem |
| Remedy: | • ROM update for controller system • Use another booting SD card having a valid digital signature |
| Error code: | SC818-00 |
| Description: | Watchdog timer error The system program fell into a bus-hold state or an endless loop of the program interruption occurred, causing other process to stop. |
| Causes: | • System program defective • Controller board defective • Optional board defective |
| Remedy: | • Turn the main power OFF/ON. • Replace the controller board. |
| Error code: | SC819-00 |
| Description: | Kernel halt error [xxxx]: Detailed error code Due to a control error, a RAM overflow occurred during system processing. One of the following messages was displayed on the operation panel. |
| Remedy: | [0x5032] HAIC-P2 error HAIC-P2 decompression error (An error occurred in the ASIC compression/decompression module.) • The code data saved in the HDD was broken for an unexpected reason. (HDD device defective) • The code data saved to memory was broken for an unexpected reason. (Memory device defective) • ASIC defective • Data other than code data was unzipped due to a software malfunction. • Turn the main power OFF/ON. • Replace the HDD. • Replace the memory • Replace the controller board. • Fix the software [0x5245] Link up error Link up transaction between Engine ASIC and Veena was not completed within 100 ms. Either one of following message appears on console if Link up error occurs. RESUME:PCI-Express bus ROOT_DL status error RESUME:PCI-Express bus DETUP status error "0x53554D45" -> Link up error Also, error code "0x5245" and detail code ""0x53554D45" -> Link up error" appears on operation panel. • Turn the main power OFF/ON. • Replace the controller board or the engine board (IPU, BCU) [0x5355] L2 status time out L2 status register between Engine ASIC and Veena was not reached the target value within 1 sec. Engine ASIC during operation was rebooted or shifted to energy saving mode. Machine reboots when SC23x, SC30x occurs. If Engine ASIC is working when rebooting (or shifting to the energy saving mode), L2 status value is not on target. The following message appears on console. SUSPEND:PCI-Express L2 Status Check Error SUSPEND:PCI-Express L2 Status Check Error Also, error code "0x5355" and detail code ""0x5350454E44" -> L2 status time out" appears on operation panel. • Turn the main power OFF/ON. • Replace the controller board or the engine board (IPU, BCU) [0x6261] HDD defective Received file system data was broken even if the initialization succeeds and there was no error reply from the HDD. Power supply disconnection during data writing to the HDD. Replace the HDD. This SC may occur when turning on the machine for the first time with a new HDD. In this case, turn the main power off/on. [0x696e] gwinit processing end If the SCS process is ended for some reason If an unexpected error occurs at SCS processing end, gwint processing also halts (this result is judged a kernel stop error, by gwinit specification) "0x69742064" -> "init died" Turn the main power OFF/ON. [0x766d] VM full error Occurs when too much RAM is used during system processing "vm_pageout: VM is full" Turn the main power OFF/ON. Console string Other error (characters on operation panel) System detected internal mismatch error • Software defective • Insufficient memory • Hardware driver defective (RAM, flash memory) • Replace with a larger capacity RAM, or flash memory. • Replace the controller board. • Replace the connected controller option with a new one. |
| Error code: | SC840-00 |
| Description: | EEPROM access error • During the I/O processing, a reading error occurred. The 3rd reading failure causes this SC code. • During the I/O processing, a writing error occurred. |
| Causes: | • Defective EEPROM |
| Error code: | SC841-00 |
| Description: | EEPROM read data error Mirrored data of the EEPROM is different from the original data in EEPROM. |
| Causes: | Data in the EEPROM is overwritten for some reason. |
| Error code: | SC842-00 |
| Description: | Nand-Flash updating verification error SCS write error (verify error) occurred at the Nand-Flash module when remote ROM or main ROM was updated. |
| Causes: | Nand-Flash defective |
| Remedy: | Turn the main power OFF/ON. |
| Error code: | SC842-01 |
| Description: | Insufficient Nand-Flash blocks (threshold exceeded) At startup, or when machine returned from low power mode, the Nand-Flash status was read and judged that the number of unusable blocks had exceeded threshold, and then SCS generated the SC code. |
| Causes: | Number of unusable blocks exceeded threshold for Nand-Flash |
| Remedy: | Replace the controller board. |
| Error code: | SC842-02 |
| Description: | Number of Nand-Flash block deletions exceeded At startup, or when the machined returned from low power mode, the Nand-Flash was read and judged that the number of deleted blocks had exceeded threshold, and then SCS generated this SC code. |
| Causes: | Number of blocks deleted exceeded threshold for Nand-Flash |
| Remedy: | Replace the controller board. |
| Error code: | SC845-01 ... SC845-05 |
| Description: | Hardware Error during Firmware Auto Update Cannot complete firmware update while retrying three times. |
| Causes: | Hardware-related error occurs in a board. The branch number of this SC represents where the error occurs. -01: BiCU -02: Controller Board -03 or -04: Operation panel board -05: FCU |
| Remedy: | Replace the board that causes the SC. |
| Error code: | SC855-01 |
| Description: | Wireless LAN board error (driver attachment failure) Wireless LAN board error (wireless LAN card: 802.11 is covered) |
| Causes: | • Defective wireless LAN board • Loose connection |
| Remedy: | • Turn the main power OFF/ON. • Replace wireless LAN board |
| Error code: | SC855-02 |
| Description: | Wireless LAN board error (driver initialization failure) Wireless LAN board error (wireless LAN card: 802.11 is covered) |
| Causes: | • Defective wireless LAN board • Loose connection |
| Remedy: | • Turn the main power OFF/ON. • Replace wireless LAN board |
| Error code: | SC858-00 |
| Description: | Data encryption conversion error (Key Setting Error) A serious error occurred during an attempt to update the encryption key. |
| Causes: | • USB Flash, other data, corrupted • Communication error caused by electrostatic noise • Controller board defective |
| Remedy: | Replace the controller board. |
| Error code: | SC858-01 |
| Description: | Data encryption conversion error (HDD Key Setting Error) A serious error occurred during an attempt to update the encryption key. |
| Causes: | • USB Flash, other data, corrupted • Communication error caused by electrostatic noise • Controller board defective |
| Remedy: | • Turn the main power OFF/ON. • If the error persists, replace the controller board. |
| Error code: | SC858-02 |
| Description: | Data encryption conversion error (NVRAM Read/Write Error) A serious error occurred after data conversion during an attempt to update the encryption key. |
| Causes: | NVRAM defective |
| Remedy: | • Replace the NVRAM. • Replace the controller board. |
| Error code: | SC858-30 |
| Description: | Data encryption conversion error (NVRAM Before Replace Error) A serious error occurred after data conversion during an attempt to update the encryption key. |
| Causes: | Software error such as conversion parameters being invalid. |
| Remedy: | • Turn the main power OFF/ON. • If the error persists, replace the controller board. |
| Error code: | SC858-31 |
| Description: | Data encryption conversion error (Other Error) A serious error occurred after data conversion during an attempt to update the encryption key |
| Causes: | Controller board defective |
| Remedy: | Replace the controller board. |
| Error code: | SC859-00 |
| Description: | Data encryption conversion HDD conversion error When the data encryption key was updated, HDD data was converted, but not correctly. Image displayed at conversion only (this SC is not displayed), but SC is displayed after machine is cycled off/on. |
| Causes: | • HDD conversion was set with the data encryption key update function, but the HDD was removed. • Machine lost power during data encryption key update • Electrostatic noise, or an HDD error occurred, during data encryption key update, and data was not encrypted. |
| Remedy: | • Check HDD connection. • Format the HDD (SP5-832: HDD formatting). • If there is a problem with the HDD, it has to be replaced. |
| Error code: | SC859-01 |
| Description: | Data encryption conversion HDD conversion error (HDD check error) When the data encryption key was updated, HDD data was converted, but not correctly. Image displayed at conversion only (this SC is not displayed), but SC is displayed after machine is cycled off/on. |
| Causes: | • HDD conversion was set with the data encryption key update function, but the HDD was removed. • Machine lost power during data encryption key update • Electrostatic noise, or an HDD error occurred, during data encryption key update, and data was not encrypted. |
| Remedy: | • Check HDD connection. • Format the HDD (SP5-832: HDD formatting). • If there is a problem with the HDD, it has to be replaced. |
| Error code: | SC859-02 |
| Description: | Data encryption conversion HDD conversion error (Power failure during conversion) When the data encryption key was updated, HDD data was converted, but not correctly. Image displayed at conversion only (this SC is not displayed), but SC is displayed after machine is cycled off/on. Details: NVRAM/HDD conversion is incomplete. |
| Causes: | Power failure occurred during encryption key update. |
| Remedy: | The display after restart instructs the user to format the HDD. |
| Error code: | SC859-10 |
| Description: | Data encryption conversion HDD conversion error (Data read/write command error) When the data encryption key was updated, HDD data was converted, but not correctly. Image displayed at conversion only (this SC is not displayed), but SC is displayed after machine is cycled off/on. Details: Abnormal DMAC return value has been received two or more times (DMAC timeout, serial communication error etc.) |
| Causes: | HDD was not successfully converted during encryption key update due to HDD errors or cable noises. |
| Remedy: | • Check HDD connection. • Format the HDD (SP5-832: HDD formatting). • If there is a problem with the HDD, it has to be replaced. |
| Error code: | SC860-00 |
| Description: | HDD startup error at main power on (HDD error) • The HDD is connected but the driver detected the following errors. • SS_NO.T_READY:/* (-2)HDD does not become READY*/ • SS_BAD_LABEL:/* (-4)Wrong partition type*/ • SS_READ_ERROR:/* (-5)Error occurred while reading or checking the label*/ • SS_WRITE_ERROR:/* (-6)Error occurred while writing or checking the label*/ • SS_FS_ERROR:/* (-7)Failed to repair the filesystem*/ • SS_MOUNT_ERROR:/* (-8)Failed to mount the filesystem*/ • SS_COMMAND_ERROR:/* (-9)Drive not responding to command*/ • SS_KERNEL_ERROR:/* (-10)Internal kernel error*/ • SS_SIZE_ERROR:/* (-11)Drive size too small*/ • SS_NO._PARTITION:/* (-12)The specified partition does not exist*/ • SS_NO._FILE:/* (-13)Device file does not exist*/ • Attempted to acquire HDD status through the driver but there has been no response for 30 seconds or more. |
| Causes: | • Unformatted HDD • Label data corrupted • HDD defective |
| Remedy: | Format the HDD (SP5-832: HDD formatting) through SP mode. |
| Error code: | SC862-00 |
| Description: | Number of the defective sector reaches the maximum count 101 defective sectors are generated at the image storage area in the HDD. |
| Causes: | SC863 occurs during the HDD reading and defective sectors are registered up to 101. |
| Remedy: | • Format the HDD with SPSP5-832. • Replace the HDD. |
| Error code: | SC863-01 ... SC863-23 |
| Description: | HDD Data Read Error HDD data cannot be read. |
| Causes: | • SC863-01 A bad sector was generated during operation. (An error occurred in an area that does not belong to a partition, such as the disk label area.) • SC863-02 to -23 A bad sector was generated during operation. (An error occurred in partitions from “a” (SC863-02) to “v” (SC863-23). |
| Remedy: | Replace the HDD when: • this SC occurred ten times or more, and • the error recurs at short intervals. • the SC repeatedly occurs in the same situation (for example, at power ON). • startup takes a long time when the main power is turned ON. It takes a long time for the operation panel to become ready after power ON because it takes time to access the HDD. Normally, HDD access after power ON takes about 5 secs. If the machine is not waiting for the engine to be ready and it still takes 20 to 30 seconds or more, there may be a problem with the HDD. Check if HDD-related SCs such as SC860 and SC863 are also occurring frequently. Print the SC log data to check them. |
| Error code: | SC864-00 |
| Description: | HD data CRC error During HD operation, the HD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HD. |
| Causes: | HD defective |
| Error code: | SC864-01 ... SC864-23 |
| Description: | HDD Data CRC Error During HDD operation, the HDD did not respond to a CRC error query. |
| Causes: | • SC864-01 A bad sector was generated during operation. (An error occurred in an area that does not belong to a partition, such as the disk label area.) • SC864-02 to -23 A bad sector was generated during operation. (An error occurred in partitions from “a” (SC863-02) to “v” (SC863-23). |
| Remedy: | • Format the HDD. • Replace the HDD. |
| Error code: | SC865-00 ... SC865-23 |
| Description: | HDD access error During HDD operation, the HDD returned an error. |
| Causes: | The HDD returned an error that does not constitute SC863 (bad sector) or SC864 (CRC error). |
| Remedy: | Replace the HDD. |
| Error code: | SC865-50 ... SC865-73 |
| Description: | HDD time-out error The machine does not detect a reply from the HDD during the HDD operation. |
| Causes: | The HDD does not respond to the read/ write command from the machine. |
| Remedy: | • Check the harness connections between the controller board and HDD. • Replace the HDD. |
| Error code: | SC866-00 |
| Description: | SD card authentication error A license error of an application that is started from the SD card was detected. |
| Causes: | Invalid program data is stored on the SD card. |
| Remedy: | Store a valid program data on the SD card. |
| Error code: | SC867-00, SC867-01, SC867-02 |
| Description: | SD card removed The SD card was removed while the machine is on. |
| Causes: | An application SD card has been removed from the slot (mount point of /mnt/sd*). |
| Remedy: | Turn the main power OFF/ON. |
| Error code: | SC868-00 |
| Description: | SD card access error The SD controller returned an error during operation. (An error occurred at the mount point of /mnt/sd0) |
| Causes: | • SD card is defective • SD controller is defective |
| Remedy: | • Reformat the SD card (using the "SD Formatter" made by Panasonic).* • Check the SD card insertion status. • Replace the SD card. • Replace the controller board. |
| Error code: | SC868-01 |
| Description: | SD card access error The SD controller returned an error during operation. (An error occurred at the mount point of /mnt/sd1) |
| Causes: | • SD card is defective • SD controller is defective |
| Remedy: | SD card used for starting an application • Turn the main power off and check the SD card insertion status. • If no problem is found, insert the SD card and turn the main power on. • If an error occurs, replace the SD card. • SD card for users • In case of a file system error, reformat the SD card (using the "SD Formatter" made by Panasonic).* • In case of a device access error, turn the main power off and check the SD card insertion status. • If no problem is found, insert the SD card and turn the main power on. • If an error occurs, use another SD card. • If the error persists even after replacing the SD card, replace the controller board. |
| Error code: | SC869-01 |
| Description: | Malfunction of the proximity sensor is detected Continuously detecting malfunction The proximity sensor keeps in a detection state and accumulated time exceeds 24 hours. |
| Causes: | The proximity sensor is disabled and is in the detection state at all times. |
| Remedy: | 1. Go to the SP5-102-203 (input check SP for the proximity sensor). 2. Cover the sensor with 10 sheets of plain paper, and then execute the SP. Make sure that it becomes "0". (Do not place your hand near the sensor, even over the paper, when covering the sensor) 3. Remove the paper from the sensor and make sure that it becomes "1". 4. If the sensor reacts normally in step 2 and 3, check if there are any other possible factors around the machine that may cause the temperature change such as a heater or a fan. (Deal with the issue as necessary) 5. Replace the proximity sensors and proximity sensor board if an abnormal value is detected during steps 2 and 3. 6. Turn on the main power on and perform steps 1, 2, and 3 again. 7. If the SC is not solved, turn the main power off and replace the harness which connects the proximity sensors and the proximity sensor board. 8. If the SC is still not solved, there is a possibility that other parts of the machine such as the connector at the controller side or the harness between proximity sensor board and IPU are broken. |
| Error code: | SC869-02 |
| Description: | Malfunction of the proximity sensor is detected Continuously non-detecting malfunction In the non-detection state, the following operations are detected 20 times continuously. • Pressing "energy saver" key or touching the operation panel • Opening/closing the plate cover or ADF • Setting the original • Opening the front cover • Opening the paper feed tray |
| Causes: | The proximity sensor is disabled and is in the non-detection state at all times. |
| Remedy: | 1. Go to the SP5-102-203 (input check SP for the proximity sensor). 2. Cover the sensor with 10 sheets of plain paper, and then execute the SP. Make sure that it becomes "0". (Do not place your hand near the sensor, even over the paper, when covering the sensor) 3. Remove the paper from the sensor and make sure that it becomes "1". 4. If the sensor reacts normally in step 2 and 3, check if there are any other possible factors around the machine that may cause the temperature change such as a heater or a fan. (Deal with the issue as necessary) 5. Replace the proximity sensors and proximity sensor board if an abnormal value is detected during steps 2 and 3. 6. Turn on the main power on and perform steps 1, 2, and 3 again. 7. If the SC is not solved, turn the main power off and replace the harness which connects the proximity sensors and the proximity sensor board. 8. If the SC is still not solved, there is a possibility that other parts of the machine such as the connector at the controller side or the harness between proximity sensor board and IPU are broken. |
| Error code: | SC870 |
| Description: | Address book data error. Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Software bug • Inconsistency of Address Book source location (machine/delivery server/LDAP server) • Inconsistency of Address Book encryption setting or encryption key (NVRAM was replaced individually without formatting the Address Book) • Address Book storage device (SD) was temporarily removed or hardware configuration does not match the application configuration. • Address Book data corruption was detected. |
| Remedy: | • Software defective. Turn the machine OFF/ON. If this is not the solution for the problem, then replace the controller firmware. • HDD defective. More Details • Do SP5846 050 (UCS (User info control service) Settings – Initialize all Directory Info.) to reset all address book data. • Reset the user information with SP5832 006 (HDD Formatting– User Information). • Replace the HDDs. • Boot the machine from the SD card. |
| Error code: | SC872-00 |
| Description: | HDD mail reception error An error was detected on the HDD immediately after the machine was turned on. |
| Causes: | • HDD defective • Power was turned off while the machine used the HDD. |
| Remedy: | • Format the HDD (SP5-832-007: HDD Formatting: Mail RX Data).). • Replace the HDD. When you do the above, the following information will be initialized. • Partly received partial mail messages. • Already-read statuses of POP3-received messages (All messages on the mail server are handled as new messages). |
| Error code: | SC873-00 |
| Description: | HDD mail reception error An error was detected on the HDD immediately after the machine was turned on. |
| Causes: | • HDD defective • Power was turned off while the machine used the HDD. |
| Remedy: | • Format the HDD (SP5-832-007 : HDD Formatting: Mail RX Data). • Replace the HDD. When you do the above, the following information will be initialized. • Sender’s mail text • Default sender name/password (SMB/FTP/NCP) • Administrator mail address • Scanner delivery history |
| Error code: | SC874 |
| Description: | Delete All error 1: HDD. A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit (B735) running from an SD card. |
| Causes: | • Error detected in HDD data delete program • Error detected in NVRAM data delete program • The "Delete All" option was not set |
| Remedy: | • Turn the main switch OFF/ON and try the operation again. • Install the Data Overwrite Security Unit again. For more, see section “1. Installation”. • HDD defective |
| Error code: | SC875 |
| Description: | Delete All error 2: Data area. An error occurred while the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B660 running from an SD card. |
| Causes: | • HDD logical formatting failed. • The modules failed to erase data. |
| Remedy: | • Turn the main switch OFF/ON and try the operation again. |
| Error code: | SC877-00 |
| Description: | Data Overwrite Security card error The "Auto Erase Memory" function of the Data Overwrite Security is set to on but it cannot be done. |
| Causes: | • Data Overwrite Security option SD card is broken. • Data Overwrite Security option SD card has been removed. |
| Remedy: | • If the SD card is broken, prepare a new Data Overwrite Security option SD card and replace the NVRAM. • If the SD card has been removed, turn the main power off and reinstall a working Data Overwrite Security option SD card. |
| Error code: | SC878-00 |
| Description: | TPM authentication error TPM electronic recognition failure |
| Causes: | • Update of system module attempted without correct update path • USB flash memory not operating correctly |
| Remedy: | Replace the controller board (PCB3). Trusted Platform Module • In computing, Trusted Platform Module (TPM) is both the name of a published specification detailing a secure crypto processor that can store cryptographic keys that protect information, as well as the general name of implementations of that specification often called the "TPM chip" or "TPM Security Device" (as designated in certain Dell BIOS settings). |
| Error code: | SC878-01 |
| Description: | USB flash error There is a problem in the file system of the USB flash memory. |
| Causes: | USB Flash system files corrupted. |
| Remedy: | Replace the controller board (PCB3). |
| Error code: | SC878-02 |
| Description: | TPM error An error occurred in either TPM or the TPM driver. |
| Causes: | TPM not operating correctly. |
| Remedy: | Replace the controller board (PCB3). |
| Error code: | SC878-03 |
| Description: | TCSD error An error occurred in the TPM software stack. |
| Causes: | • TPM, TPM software cannot start • A file required by TPM is missing |
| Remedy: | Replace the controller board (PCB3). |
| Error code: | SC878-20 |
| Description: | Random number generator self check error The unusual status is detected during the self test of generated random number seed. |
| Causes: | TPM defective. (The random number seed is generated by TPM) |
| Remedy: | 1. Turn ON the main power. 2. Replace the controller board (PCB3). |
| Error code: | SC880-00 |
| Description: | MLB error |
| Causes: | The response is not received within the specified time during the access to the MLB. Defective MLB |
| Remedy: | • Replace the MLB • Remove the MLB |
| Error code: | SC899-00 |
| Description: | Software performance error (signal reception end) Unknown software error occurred. |
| Causes: | Occurs when an internal program behaves abnormally. |
| Remedy: | In the case of a hardware defect • Replace the hardware. In the case of a software error • Turn the main power OFF/ON. • Try updating the firmware. |
| Error code: | SC900-00 |
| Description: | Electric counter error The electric total counter value is out of specification. Error is detected when increasing the total counter. |
| Causes: | • Unexpected NV-RAM is attached. • NV-RAM defective • NV-RAM data corrupted. • Data written to unexpected area because of external factor etc. • The count requested by the SRM on receiving PRT is not completed. |
| Remedy: | Replace the NV-RAM. |
| Error code: | SC990-00 |
| Description: | Software operation error Software attempted an unexpected operation. |
| Causes: | • Parameter error • Internal parameter error • Insufficient work memory • Operation error caused by abnormalities that are normally undetectable. |
| Remedy: | • Turn the main power off/on. • Reinstall the software of the controller and BCU board. |
| Error code: | SC991-00 |
| Description: | Recoverable software operation error Software attempted an unexpected operation. SC991 covers recoverable errors as opposed toCS990. |
| Causes: | • Parameter error • Internal parameter error • Insufficient work memory • Operation error caused by abnormalities that are normally undetectable. |
| Remedy: | Logging only |
| Error code: | SC992-00 |
| Description: | Undefined SC issued. An SC, that is not controlled by the system, occurred. |
| Causes: | • An SC for the previous model was used mistakenly, etc. • Basically a software bug. |
| Remedy: | Turn the main power OFF/ON. |
| Error code: | SC997-00 |
| Description: | Application function selection error The application selected by the operation panel key operated abnormally (No response, abnormal ending). |
| Causes: | Software bug (mainly the application) |
| Remedy: | • Check the optional RAM, DIMM, boards required by the application program. • Check if the combination of downloaded programs are correct. |
| Error code: | SC998-00 |
| Description: | Application start error • No application was registered to system within a specified time after the main power was turned on. (No application starts/All applications have been terminated abnormally) • Application started but cannot be drawn now for some reason. |
| Causes: | • Software bug (mainly the application) • The optional RAM, DIMM, boards required by the application program. Are not installed correctly. |
| Remedy: | • Turn the main power OFF/ON. • Check the optional RAM, DIMM, boards • Check the combination of programs • Replace the controller board. |
Парткод
Название
RICOH TYPE MP401 Принт-картридж черный
