Ricoh MP5002SP
Рейтинг
Модули
TONER SUPPLY UNIT
ARDF Drive Section 1
ELECTRICAL SECTION 2
DRIVE SECTION 4
By-pass Feed Section 2
Original Transfer 1
EXTERIOR 2
PAPER EXIT SECTION 2
Controller Section 2
SCANNER SECTION 3
ELECTRICAL SECTION 3
DUPLEX UNIT 4
LD unit
Drive Section 1
ARDF Frame Section
TRANSFER BELT UNIT 1
By-pass Feed Section 1
PAPER EXIT SECTION 1
PAPER TRAY
ELECTRICAL SECTION 4
PCDU 2
FRAME SECTION
ELECTRICAL SECTION 1
Controller Section 1
ELECTRICAL SECTION 5
EXTERIOR 1
Scanner Section 1
PAPER FEED SECTION
DUPLEX UNIT 2
DRIVE SECTION 3
ARDF Exterior
PCDU 1
OPERATION PANEL
ARDF Drive Section 2
Original Transfer 2
Original Transfer 3
Scanner Section 4
DUPLEX UNIT 1
Original Feed 3
DUPLEX UNIT 3
SCANNER SECTION 2
Original Feed 1
FUSING UNIT 2
ARDF Electrical Section
FUSING UNIT 1
PAPER REGISTRATION
TRANSFER BELT UNIT 2
Original Feed 2
FUSING UNIT 3
DUPLEX UNIT 5
DRIVE SECTION 2
Детали DUPLEX UNIT 5
| Деталь: | TONER SUPPLY UNIT |
| Парткод: | D129 3209 |
| Деталь: | Slide Rail: Toner Supply Unit |
| Парткод: | B077 3262 |
| Деталь: | Seal - Slide Rail |
| Парткод: | A232 3266 |
| Деталь: | Cover - Toner Bottle Assy |
| Парткод: | A232 3240 |
| Деталь: | Bottle Chuck |
| Парткод: | A134 3180 |
| Деталь: | SLIDER ASSY |
| Парткод: | A232 3252 |
| Деталь: | Chuck Shaft |
| Парткод: | A232 3251 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3566 |
| Деталь: | Decal: Main Switch: On-standby |
| Парткод: | D011 1252 |
| Деталь: | Decal: Main Switch: On-standby: EU |
| Парткод: | D011 1253 |
| Деталь: | Spring Plate - Toner Bottle |
| Парткод: | A232 3263 |
| Деталь: | Shaft - Slide |
| Парткод: | D009 3265 |
| Деталь: | Stopper - Slide Rail |
| Парткод: | A232 3264 |
| Деталь: | Heater Stopper |
| Парткод: | D009 5892 |
| Деталь: | Heater: PCD: NA: Sub-assy |
| Парткод: | D011 5841 |
| Деталь: | Heater: PCD: EU: Sub-assy |
| Парткод: | D011 5842 |
| Деталь: | Harness: AC: Heater |
| Парткод: | D009 5611 |
| Деталь: | Stepper Motor: DC4.08V 2.4W |
| Парткод: | B802 1812 |
| Деталь: | Rubber Bushing - 6 45hs |
| Парткод: | AA101021 |
| Деталь: | Bracket: Reverse: Drive |
| Парткод: | B802 1815 |
| Деталь: | COLLAR |
| Парткод: | B044 1825 |
| Деталь: | Timing Belt: 40S2M128 |
| Парткод: | J503 3116 |
| Деталь: | Sensor Shielding Plate |
| Парткод: | G570 1225 |
| Деталь: | Bracket: Sensor: Pickup |
| Парткод: | B8021985 |
| Деталь: | Photointerruptor: Lg2a14nl1 |
| Парткод: | AW02 0198 |
| Деталь: | Timing Belt: 40S2M120 |
| Парткод: | AA04 3323 |
| Деталь: | Bracket: Pickup: Drive |
| Парткод: | B802 1925 |
| Деталь: | Stepper Motor: PM: S2M: T15: Assy |
| Парткод: | B700 5805 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Cam: Stopper Pawl |
| Парткод: | B802 1951 |
| Деталь: | Gear: Stopper: Original Insert: Z25 |
| Парткод: | B802 1956 |
| Деталь: | Gear - 18Z |
| Парткод: | B351 1781 |
| Деталь: | Timing Pulley: T33-Z17 |
| Парткод: | B802 1931 |
| Деталь: | Stopper: Cam: Pickup |
| Парткод: | B802 1942 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Feeler: Cam: Pickup |
| Парткод: | B802 1943 |
| Деталь: | Gear: Drive: Arm: Pickup |
| Парткод: | B802 1946 |
| Деталь: | Cam: Pickup |
| Парткод: | B802 1941 |
| Деталь: | Middle Exhaust Duct - Upper |
| Парткод: | D0091366 |
| Деталь: | Middle Exhaust Duct - Lower |
| Парткод: | D0091367 |
| Деталь: | Front Upper Duct |
| Парткод: | D0091368 |
| Деталь: | Front Lower Duct |
| Парткод: | D0091369 |
| Деталь: | Fan Motor - Mm60 DC24V |
| Парткод: | B223 1332 |
| Деталь: | Harness Guide - Safety Switch |
| Парткод: | D009 5898 |
| Деталь: | Base - Right Safety Switch |
| Парткод: | D009 5866 |
| Деталь: | Right Lower Lever - Safety Switch |
| Парткод: | D009 5869 |
| Деталь: | Guide Plate - Safety Switch |
| Парткод: | D009 5867 |
| Деталь: | Spring - Right Safety Switch |
| Парткод: | D009 5896 |
| Деталь: | Right Lever - Safety Switch |
| Парткод: | D009 5868 |
| Деталь: | Shaft - Safety Switch |
| Парткод: | D009 5857 |
| Деталь: | Middle Lever - Safety Switch |
| Парткод: | D009 5864 |
| Деталь: | Cam - Safety Switch |
| Парткод: | D009 5865 |
| Деталь: | Left/Right Lever - Safety Switch |
| Парткод: | D009 5858 |
| Деталь: | Left Lever - Safety Switch |
| Парткод: | D009 5863 |
| Деталь: | Tension Spring: Safety Switch: Left |
| Парткод: | D009 5895 |
| Деталь: | Base - Left Safety Switch |
| Парткод: | D009 5840 |
| Деталь: | Fan Motor - DC 2.16W |
| Парткод: | AX64 0194 |
| Деталь: | Exit Duct - MM60 |
| Парткод: | D009 1371 |
| Деталь: | Harness - Safety Switch |
| Парткод: | D009 5425 |
| Деталь: | Feed Drive Shaft |
| Парткод: | B223 1189 |
| Деталь: | Grip Shaft |
| Парткод: | B223 1183 |
| Деталь: | Drive Joint |
| Парткод: | B223 1186 |
| Деталь: | Drum Stay: Drive Unit |
| Парткод: | B2231354 |
| Деталь: | Gear - 33Z/44Z |
| Парткод: | AB01 7699 |
| Деталь: | Gear - 38Z |
| Парткод: | AB01 1258 |
| Деталь: | Timing Belt: 40S3M162 |
| Парткод: | AA04 3585 |
| Деталь: | Timing Pulley - 28Z/30T |
| Парткод: | AB03 0781 |
| Деталь: | Gear - 32Z |
| Парткод: | AB01 1259 |
| Деталь: | Bracket: Paper Feed |
| Парткод: | B223 1180 |
| Деталь: | Magnetic Clutch - 32Z |
| Парткод: | AX20 0289 |
| Деталь: | Magnetic Clutch Bracket |
| Парткод: | B223 1187 |
| Деталь: | Bushing: Flange Type: DIA6 |
| Парткод: | AA08 0346 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Cushion: DC Stepper Motor |
| Парткод: | AA16 1180 |
| Деталь: | Stepper Motor DC24V |
| Парткод: | B223 1188 |
| Деталь: | Timing Belt: 40S2M144 |
| Парткод: | B700 2649 |
| Деталь: | Gear Pulley |
| Парткод: | AB01 7493 |
| Деталь: | Guide: Gear |
| Парткод: | B223 2694 |
| Деталь: | COLLAR |
| Парткод: | B044 1825 |
| Деталь: | Bracket: Stepper Motor |
| Парткод: | B223 2691 |
| Деталь: | Stepper Motor: Assy |
| Парткод: | B223 2745 |
| Деталь: | Rubber Bushing - 6 45hs |
| Парткод: | AA10 1021 |
| Деталь: | Total Counter: 7Fig: 24V |
| Парткод: | AX31 0045 |
| Деталь: | Grip Bracket - Right Rear |
| Парткод: | D0091088 |
| Деталь: | Bracket: Total Counter |
| Парткод: | B223 5846 |
| Деталь: | Cover: Guide Plate: Exit |
| Парткод: | B223 2623 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Guide Plate: Exit |
| Парткод: | B223 2622 |
| Деталь: | Cover: Manual Feed Unit |
| Парткод: | D129 2621 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | Feed Roller - Manual Feed |
| Парткод: | AF03 1046 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Shaft: Feed |
| Парткод: | AA14 0777 |
| Деталь: | Stay: Feed |
| Парткод: | B223 2629 |
| Деталь: | Gear - 23Z |
| Парткод: | AB01 1387 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | AF03 0049 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3568 |
| Деталь: | Pick-up Arm - Manual Feed |
| Парткод: | G060 2932 |
| Деталь: | DC Solenoid: Pickup |
| Парткод: | B223 2632 |
| Деталь: | Spring: Release: Pickup |
| Парткод: | B223 2633 |
| Деталь: | Harness: Manual Feed |
| Парткод: | B223 2659 |
| Деталь: | Guide Sheet - Manual Feed |
| Парткод: | D009 2552 |
| Деталь: | Transport Roller - Duplex Exit |
| Парткод: | D009 2555 |
| Деталь: | Support Stay: Arm |
| Парткод: | B223 2634 |
| Деталь: | Torsion Spring: 27N |
| Парткод: | B223 2636 |
| Деталь: | Paper End Sensor |
| Парткод: | AW50 0035 |
| Деталь: | Arm: Manual Feed: Front |
| Парткод: | B223 2651 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2102 |
| Деталь: | Arm: Manual Feed: Short: Front |
| Парткод: | D129 2657 |
| Деталь: | Ground Plate: Front: Manual Feed |
| Парткод: | D029 2612 |
| Деталь: | Guide Plate: Separator: Assy |
| Парткод: | D029 2709 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3016 |
| Деталь: | Roller Clutch - 6x14x10 |
| Парткод: | AA08 3018 |
| Деталь: | Ground Plate: Rear: Manual Feed |
| Парткод: | D029 2611 |
| Деталь: | One-way Clutch |
| Парткод: | AA08 3014 |
| Деталь: | Magnetic clutch |
| Парткод: | AX20 2007 |
| Деталь: | Bracket: Arm: Manual Feed: Rear |
| Парткод: | B223 2637 |
| Деталь: | Arm: Manual Feed: Rear |
| Парткод: | B223 2652 |
| Деталь: | Arm: Manual Feed: Short: Rear |
| Парткод: | D129 2658 |
| Деталь: | Bushing - 6 6mm |
| Парткод: | A259 6754 |
| Деталь: | Gear -20Z |
| Парткод: | AB01 1416 |
| Деталь: | Gear: Z16 |
| Парткод: | B223 2608 |
| Деталь: | Shaft: Separator: Drive |
| Парткод: | AA14 0778 |
| Деталь: | Separation Roller - Manual Feed |
| Парткод: | AF03 2046 |
| Деталь: | Torque Limiter Mechanical Clutch: 40mnm: DIA18 |
| Парткод: | D129 2783 |
| Деталь: | Shaft: Separator: Driven: Assy |
| Парткод: | B180 2871 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3499 |
| Деталь: | SPRING |
| Парткод: | AA06 0872 |
| Деталь: | Arm: Tightener |
| Парткод: | B223 2681 |
| Деталь: | Idler Gear - 25z |
| Парткод: | AB01 1223 |
| Деталь: | Gear: Z31 |
| Парткод: | B223 2686 |
| Деталь: | Gear: 25Z |
| Парткод: | B223 2683 |
| Деталь: | Gear: Z28 |
| Парткод: | B223 2689 |
| Деталь: | Drum Stay: Drive |
| Парткод: | B223 2696 |
| Деталь: | Guide: Scanning: Entrance: Lower |
| Парткод: | B802 3415 |
| Деталь: | Sheet: Roller: Scanning: Entrance |
| Парткод: | B802 3413 |
| Деталь: | Sheet: Scanning: Entrance |
| Парткод: | D630 3413 |
| Деталь: | Roller: Scanning: Driven |
| Парткод: | B802 3471 |
| Деталь: | Shaft: Driven: Entrance |
| Парткод: | B802 3492 |
| Деталь: | Bracket: Entrance: Pressure: Assy |
| Парткод: | B802 3431 |
| Деталь: | Compression Spring: 3.3n |
| Парткод: | B802 3435 |
| Деталь: | Stay: Scanning: Entrance: Lower |
| Парткод: | B802 3422 |
| Деталь: | Guide Plate: Scanning |
| Парткод: | B802 3511 |
| Деталь: | SCREW |
| Парткод: | AA14 3569 |
| Деталь: | Guide: Scanning: Exit: Lower |
| Парткод: | B802 3553 |
| Деталь: | Plate: Exit: Pressure: Auxiliary |
| Парткод: | B802 3566 |
| Деталь: | Spring Plate: Scanning: Exit: Driven: Upper |
| Парткод: | B802 3567 |
| Деталь: | Spring Plate: Scanning: Exit: Driven: Lower |
| Парткод: | B802 3569 |
| Деталь: | Stay: Scanning: Exit: Lower |
| Парткод: | B802 3561 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | Stopper: Guide: Reverse |
| Парткод: | B802 2291 |
| Деталь: | Photo Refiection Sensor: Exit |
| Парткод: | GW01 0007 |
| Деталь: | Bracket: Sensor: Scanning: Exit |
| Парткод: | B802 3851 |
| Деталь: | Discharge Brush: Reverse |
| Парткод: | B802 3755 |
| Деталь: | Spring Plate |
| Парткод: | B802 3711 |
| Деталь: | Exit Driven Roller |
| Парткод: | B789 3712 |
| Деталь: | Scanning Driven Shaft |
| Парткод: | B789 3491 |
| Деталь: | DC Solenoid: Transmited Rubber Stamp |
| Парткод: | B714 5006 |
| Деталь: | Shaft: Driven: Exit |
| Парткод: | B802 3592 |
| Деталь: | Sheet: Auxiliary: Scanning: Entrance |
| Парткод: | B802 3417 |
| Деталь: | Sensor Barcket |
| Парткод: | B802 3442 |
| Деталь: | Cover: Scanner: Left: EXP |
| Парткод: | D144 1334 |
| Деталь: | Cover: Left: Upper |
| Парткод: | D129 1282 |
| Деталь: | End Fence: Exit |
| Парткод: | D129 4487 |
| Деталь: | Tray: Exit |
| Парткод: | D129 4486 |
| Деталь: | Cover: Upper |
| Парткод: | D144 1261 |
| Деталь: | Cover: Inner Back: Upper: EXP |
| Парткод: | D129 1262 |
| Деталь: | Cover: Inner Back: Middle: EXP |
| Парткод: | D144 1274 |
| Деталь: | Cover: Inner Back |
| Парткод: | D129 1263 |
| Деталь: | Cover: Paper Exit Sub-unit: Upper |
| Парткод: | D144 1266 |
| Деталь: | Cover: Right: Upper Middle |
| Парткод: | D129 1273 |
| Деталь: | Sheet: Side: NA/AA |
| Парткод: | D129 1545 |
| Деталь: | Cover: Scanner: Right: EXP |
| Парткод: | D144 1336 |
| Деталь: | Cover: Scanner: Rear: EXP |
| Парткод: | D144 1338 |
| Деталь: | Cover: Lever: Lock: PCD |
| Парткод: | D129 2247 |
| Деталь: | Base - Lock Lever |
| Парткод: | D009 2254 |
| Деталь: | Spring Plate - Lock Lever |
| Парткод: | D009 2249 |
| Деталь: | Guide Plate: Lever: Lock: PCD |
| Парткод: | D129 2248 |
| Деталь: | Inner Cover: Upper: Right |
| Парткод: | D129 1243 |
| Деталь: | Case: Remove Paper Dust |
| Парткод: | D129 2616 |
| Деталь: | Cover: Scanner: Front |
| Парткод: | D129 1318 |
| Деталь: | Cover: Left: Cover |
| Парткод: | D129 1283 |
| Деталь: | Decal: Caution: Original: English |
| Парткод: | D129 6610 |
| Деталь: | EXIT ROLLER |
| Парткод: | D009 4444 |
| Деталь: | Upper Stay |
| Парткод: | D009 4428 |
| Деталь: | Transport Roller |
| Парткод: | D009 4445 |
| Деталь: | BUSHING - M4 |
| Парткод: | H053 2208 |
| Деталь: | Discharge Brush - Exit |
| Парткод: | D009 4443 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Exit Guide Plate - Upper |
| Парткод: | D009 4442 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF04 0575 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Front Side Plate |
| Парткод: | D009 4434 |
| Деталь: | Separation Plate - Paper Exit |
| Парткод: | D009 4406 |
| Деталь: | Lower Guide Plate - Exit |
| Парткод: | D009 4412 |
| Деталь: | Guide Roller |
| Парткод: | AF04 0571 |
| Деталь: | Roller: Guide: pFA |
| Парткод: | B223 4428 |
| Деталь: | Driven Roller Shaft |
| Парткод: | D009 4422 |
| Деталь: | Roller: Auxiliary: Driven: DIA16: pFA |
| Парткод: | B223 4435 |
| Деталь: | Spring - Lower Guide Plate |
| Парткод: | D009 4419 |
| Деталь: | Bushing - Lower Guide Plate |
| Парткод: | D009 4498 |
| Деталь: | Lower Stay - Exit |
| Парткод: | D009 4413 |
| Деталь: | Spring - Exit Pressure |
| Парткод: | D009 4477 |
| Деталь: | Shaft: Pressure Roller |
| Парткод: | B213 4460 |
| Деталь: | Entrance Arm |
| Парткод: | D009 4491 |
| Деталь: | Spring - Entrance Pressure |
| Парткод: | D009 4476 |
| Деталь: | Pressure Roller: Entrance |
| Парткод: | AF04 0601 |
| Деталь: | Exit Arm |
| Парткод: | D009 4492 |
| Деталь: | Pressure Roller: 15 |
| Парткод: | AF04 0599 |
| Деталь: | Bracket - Contact Point |
| Парткод: | D009 4493 |
| Деталь: | Spring Plate - Exit Roller |
| Парткод: | D009 4496 |
| Деталь: | Lower Supporting Plate |
| Парткод: | D009 4478 |
| Деталь: | Rear Side Plate |
| Парткод: | D009 4431 |
| Деталь: | Timing Belt - 30S2M172 |
| Парткод: | D009 4466 |
| Деталь: | Timing Pulley - 22T |
| Парткод: | D009 4465 |
| Деталь: | Gear - 22Z |
| Парткод: | D009 4462 |
| Деталь: | Gear/Pulley - 22Z/22T |
| Парткод: | D009 4463 |
| Деталь: | Guide - Fax Control Unit |
| Парткод: | D009 5881 |
| Деталь: | PCB: CTL: 50 |
| Парткод: | D129 5725 |
| Деталь: | PCB: CTL: 40 |
| Парткод: | D129 5726 |
| Деталь: | Cap: Connector: USB |
| Парткод: | B154 5865 |
| Деталь: | SD-Card: P/S Unit: Assy |
| Парткод: | D129 5740 |
| Деталь: | Right Rail - Small |
| Парткод: | D009 5899 |
| Деталь: | Left Rail - Fax Control Unit |
| Парткод: | D009 5891 |
| Деталь: | PCB: Memory: 512MB |
| Парткод: | M052 5391 |
| Деталь: | Grip: C/T Box: Upper: IG |
| Парткод: | D129 5870 |
| Деталь: | Panel: Interface: SECC |
| Парткод: | B154 5869 |
| Деталь: | Grip: Control Board: IG |
| Парткод: | D144 5885 |
| Деталь: | Cover: Fax Control Unit: Large |
| Парткод: | D129 5872 |
| Деталь: | Cover: Control Unit |
| Парткод: | D129 5890 |
| Деталь: | NVRAM |
| Парткод: | D129 9590 |
| Деталь: | Cap - Lan Connector |
| Парткод: | B129 5008 |
| Деталь: | PCB: SCNB |
| Парткод: | D129 5350 |
| Деталь: | Original Sensor - 66mm |
| Парткод: | AW01 0133 |
| Деталь: | Bracket: Original Sensor: Sub Scanning |
| Парткод: | D129 1815 |
| Деталь: | Gasket: 13x17x35: R |
| Парткод: | D029 1830 |
| Деталь: | Gasket: 9x3x10 |
| Парткод: | D029 1832 |
| Деталь: | Gasket: 13x17x10: R |
| Парткод: | D029 1831 |
| Деталь: | Inner Cover: Ground Plate: Peen |
| Парткод: | D029 1789 |
| Деталь: | Interface Cable: Scanner: LVDS: Assy |
| Парткод: | D129 5531 |
| Деталь: | Lens: Holder: Assy |
| Парткод: | D129 1771 |
| Деталь: | Harness: SIO: Scanner Unit |
| Парткод: | D089 5217 |
| Деталь: | Bracket: Guide: Harness: Base |
| Парткод: | D129 1816 |
| Деталь: | Heater: Option: 120V: 9W |
| Парткод: | B229 1687 |
| Деталь: | Heater: Option: 230V: 9W |
| Парткод: | B229 1688 |
| Деталь: | Decal: Main Switch: On-standby: EU |
| Парткод: | D011 1253 |
| Деталь: | Fan Motor MM80 |
| Парткод: | AX64 0159 |
| Деталь: | Upper Fusing Duct |
| Парткод: | D009 1351 |
| Деталь: | Lower Fusing Duct |
| Парткод: | D0091352 |
| Деталь: | Connector bracket |
| Парткод: | D009 5852 |
| Деталь: | Sponge: Duct: Exhaust: 1 |
| Парткод: | D0091358 |
| Деталь: | Small Bracket - BICU |
| Парткод: | D009 5876 |
| Деталь: | Cover - Connector |
| Парткод: | B2381088 |
| Деталь: | Connector bracket |
| Парткод: | B223 1065 |
| Деталь: | AC Harness - Heater |
| Парткод: | D009 5615 |
| Деталь: | Bracket - Heater Connector |
| Парткод: | D009 5856 |
| Деталь: | Rear Exhaust Duct - Left |
| Парткод: | D0091355 |
| Деталь: | Bracket: Base: Connector |
| Парткод: | B223 5848 |
| Деталь: | Cover - Electrical Components |
| Парткод: | D009 2527 |
| Деталь: | Rear Exhaust Duct - Right |
| Парткод: | D0091354 |
| Деталь: | Sponge: Duct: Exhaust: 2 |
| Парткод: | D0091359 |
| Деталь: | Transport Roller 1 |
| Парткод: | D009 4662 |
| Деталь: | Transport Roller 2 |
| Парткод: | D009 4663 |
| Деталь: | Timing Belt: 30S2M182 |
| Парткод: | B223 4512 |
| Деталь: | Timing Belt: 30S2M234 |
| Парткод: | B223 4536 |
| Деталь: | Timing Belt: 30S2M312 |
| Парткод: | B223 4511 |
| Деталь: | Roller Clutch: T24 |
| Парткод: | B223 4529 |
| Деталь: | Pulley: T35/T33 |
| Парткод: | B223 4544 |
| Деталь: | Pulley: T26/T24 |
| Парткод: | B223 4527 |
| Деталь: | Roller Clutch: T26 |
| Парткод: | B223 4535 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Roller Clutch: T24 |
| Парткод: | B223 4514 |
| Деталь: | Guide Plate: Left Lower |
| Парткод: | B223 4502 |
| Деталь: | Tension Spring: Driven Roller |
| Парткод: | B223 4553 |
| Деталь: | Bushing: DIA4 |
| Парткод: | B223 4552 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | D009 4664 |
| Деталь: | Spring Cover - Transfer Unit |
| Парткод: | D009 3860 |
| Деталь: | Pressure Spring - Transfer Unit |
| Парткод: | AA06 3448 |
| Деталь: | Guide Plate - Holder |
| Парткод: | D009 4551 |
| Деталь: | Terminal Holder - Transfer Unit |
| Парткод: | D009 3861 |
| Деталь: | Sensor Harness |
| Парткод: | D009 3884 |
| Деталь: | Front Torsion Spring |
| Парткод: | D009 4541 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | Holder Shaft - Transfer Unit |
| Парткод: | D009 4545 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3303 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | Decal: Positioning Display: Development |
| Парткод: | B234 3177 |
| Деталь: | Optical Writing Unit: Assy |
| Парткод: | D129 1860 |
| Деталь: | Cover - Polygon Motor |
| Парткод: | D009 1861 |
| Деталь: | Decal - LD |
| Парткод: | G029 1980 |
| Деталь: | Shield Glass |
| Парткод: | AC01 5025 |
| Деталь: | Polygon Scanner Motor: DC: Brushless: 16.8W |
| Парткод: | AX06 0416 |
| Деталь: | Harness - Imaging Unit |
| Парткод: | D009 5570 |
| Деталь: | Sync Detector Board |
| Парткод: | D009 5325 |
| Деталь: | Laser Diode Unit: Assy |
| Парткод: | D129 1870 |
| Деталь: | Harness: Laser Diode Control |
| Парткод: | D009 5571 |
| Деталь: | Spring - Laser Diode Unit |
| Парткод: | AA06 3445 |
| Деталь: | Positioning Pin - Laser Unit Assy |
| Парткод: | A2321937 |
| Деталь: | Joint Cover |
| Парткод: | D0091182 |
| Деталь: | Joint - Cleaning |
| Парткод: | D009 1183 |
| Деталь: | Spacer - M6 |
| Парткод: | AA13 2208 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 4284 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 4283 |
| Деталь: | Gear - 26Z/90Z |
| Парткод: | AB01 4280 |
| Деталь: | Gear - 40Z |
| Парткод: | AB01 4281 |
| Деталь: | Connector Bracket - Fusing |
| Парткод: | D0091090 |
| Деталь: | AC Harness - Fusing |
| Парткод: | D009 5620 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3744 |
| Деталь: | Gear - 26Z/30Z |
| Парткод: | AB01 4282 |
| Деталь: | Shaft - Paddle Rooler Drive |
| Парткод: | D009 1164 |
| Деталь: | Brushless Motor: DC24V 18W |
| Парткод: | AX06 0356 |
| Деталь: | Photointerruptor: Flat: 7mm |
| Парткод: | AW02 0150 |
| Деталь: | Interface Harness - Web Sensor |
| Парткод: | D009 5500 |
| Деталь: | Sensor bracket |
| Парткод: | D0091193 |
| Деталь: | Bracket - Fusing Cleaning Drive |
| Парткод: | D0091187 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 1523 |
| Деталь: | Gear - 36Z |
| Парткод: | AB01 1524 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 1526 |
| Деталь: | Gear - 32Z |
| Парткод: | AB01 1525 |
| Деталь: | Gear - 14Z/32Z |
| Парткод: | AB01 1527 |
| Деталь: | Gear - 14Z/32Z |
| Парткод: | AB01 1528 |
| Деталь: | Motor Holder |
| Парткод: | D0091194 |
| Деталь: | MOTOR BRACKET |
| Парткод: | D0091195 |
| Деталь: | Motor: DC5V 0.71 W |
| Парткод: | AX04 0167 |
| Деталь: | Brushless Motor - DC 11W |
| Парткод: | AX06 0355 |
| Деталь: | Bracket - Paddle Roller Drive |
| Парткод: | D009 1161 |
| Деталь: | Bushing - 8mm |
| Парткод: | AA08 0347 |
| Деталь: | Timing Pulley - 24T |
| Парткод: | AB030815 |
| Деталь: | Timing Belt - 60S3M177 |
| Парткод: | AA04 3656 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 7743 |
| Деталь: | Holder - Paddle Roller Drive |
| Парткод: | D009 1158 |
| Деталь: | Positioning Plate: Front |
| Парткод: | B802 1121 |
| Деталь: | Positioning Plate: Rear |
| Парткод: | B802 1131 |
| Деталь: | Pressure plate |
| Парткод: | B802 4611 |
| Деталь: | Cushion: Pressure Plate: Left |
| Парткод: | B802 4632 |
| Деталь: | Sound Proofing Material: Cover: Rear |
| Парткод: | B802 4712 |
| Деталь: | Grip: Lower |
| Парткод: | D630 1261 |
| Деталь: | Screw: Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Hinge: Left: Assy |
| Парткод: | B802 1321 |
| Деталь: | Damper: Hinge: Right: Assy |
| Парткод: | B802 1361 |
| Деталь: | Filter - DF Open Sensor |
| Парткод: | A8591841 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Drum Stay: Pressure Plate |
| Парткод: | D630 4621 |
| Деталь: | Pressure Plate Tape |
| Парткод: | B477 2715 |
| Деталь: | Transfer Unit: EXP: Assy |
| Парткод: | D009 3806 |
| Деталь: | Driven Roller - Transfer Unit |
| Парткод: | A232 3885 |
| Деталь: | Roller: Bias |
| Парткод: | B213 3889 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 2054 |
| Деталь: | Earth Terminal - Transfer Belt |
| Парткод: | D009 3935 |
| Деталь: | Terminal - Transfer Belt |
| Парткод: | D009 3937 |
| Деталь: | Bias Terminal - Transfer Belt |
| Парткод: | D009 3934 |
| Деталь: | Spring: Release: Transfer Belt |
| Парткод: | AA06 1020 |
| Деталь: | Front Bushing - Bias Roller |
| Парткод: | D009 3890 |
| Деталь: | Transfer Belt Roller |
| Парткод: | A232 3926 |
| Деталь: | Drive Roller - Transfer Belt |
| Парткод: | D009 3894 |
| Деталь: | Sheet: Preventfence: Transfer Belt |
| Парткод: | D009 3954 |
| Деталь: | Scraper - Drive Roller |
| Парткод: | D009 3948 |
| Деталь: | Pulley Pin |
| Парткод: | G024 1314 |
| Деталь: | Gear - 31Z |
| Парткод: | AB01 1282 |
| Деталь: | Transfer belt |
| Парткод: | A232 3880 |
| Деталь: | Frame - Transfer Belt |
| Парткод: | D009 3883 |
| Деталь: | Arm - Transfer Belt |
| Парткод: | D009 3893 |
| Деталь: | Manual Feed Table: Assy |
| Парткод: | D129 2740 |
| Деталь: | Side Fence: Front |
| Парткод: | D129 2674 |
| Деталь: | Side Fence: Rear |
| Парткод: | D129 2673 |
| Деталь: | Grip: Side Fence: Manual Feed |
| Парткод: | D129 2726 |
| Деталь: | Spring Plate: Stopper |
| Парткод: | B223 2668 |
| Деталь: | Decal: Side Fence: Manual Feed |
| Парткод: | D129 2675 |
| Деталь: | Decal: Paper Set Direction: Manual Feed: EX |
| Парткод: | D129 2745 |
| Деталь: | Cover: Manual Feed |
| Парткод: | D129 2661 |
| Деталь: | Decal: Scale: Manual Feed |
| Парткод: | D129 2748 |
| Деталь: | Harness: Paper Size Sensor: Manual Feed |
| Парткод: | D029 2769 |
| Деталь: | Paper size sensor |
| Парткод: | AW50 0031 |
| Деталь: | Rack: Manual Feed |
| Парткод: | B223 2713 |
| Деталь: | Gear: 16Z |
| Парткод: | B223 2666 |
| Деталь: | Extension Tray: Manual Feed |
| Парткод: | D129 2667 |
| Деталь: | MANUAL FEED TABLE |
| Парткод: | D129 2662 |
| Деталь: | Feeler: Paper Size Sensor: Manual Feed |
| Парткод: | D029 2664 |
| Деталь: | Photointerruptor: LGRC102 |
| Парткод: | AW02 0204 |
| Деталь: | Decal: Tray: Manual Feed: Extension Tray: E |
| Парткод: | D129 2743 |
| Деталь: | Cover: Harness: Manual Feed Table |
| Парткод: | D029 2710 |
| Деталь: | Paper Exit Unit: Main: Assy |
| Парткод: | D009 4420 |
| Деталь: | DC Solenoid - Exit |
| Парткод: | D009 4430 |
| Деталь: | Tension Spring Release |
| Парткод: | D009 4457 |
| Деталь: | Lever - Entrance Gate |
| Парткод: | D009 4438 |
| Деталь: | Bushing - 4mm |
| Парткод: | D009 4439 |
| Деталь: | Cushion - DC Solenoid |
| Парткод: | D009 4455 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Entrance Gate |
| Парткод: | D009 4436 |
| Деталь: | BUSHING - M4 |
| Парткод: | H053 2208 |
| Деталь: | Transport Roller |
| Парткод: | D009 4445 |
| Деталь: | Exit Guide Plate - Upper Right |
| Парткод: | D009 4441 |
| Деталь: | Stepped Tapping Screw - M3 |
| Парткод: | D009 4418 |
| Деталь: | Bracket - Fusing Exit Sensor |
| Парткод: | D009 4408 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0127 |
| Деталь: | Gear - 22Z |
| Парткод: | D009 4464 |
| Деталь: | Exit Sensor Bracket |
| Парткод: | D009 4447 |
| Деталь: | Harness - Paper Exit Unit |
| Парткод: | D009 4499 |
| Деталь: | Feeler - Overflow |
| Парткод: | D009 4407 |
| Деталь: | Shaft: Feeler: Overflow |
| Парткод: | B223 4497 |
| Деталь: | Photointerruptor: Flat |
| Парткод: | AW02 0145 |
| Деталь: | Gear - 17Z |
| Парткод: | D009 4461 |
| Деталь: | Gear - 17Z |
| Парткод: | D009 4469 |
| Деталь: | Stepper Motor Bracket |
| Парткод: | D009 4471 |
| Деталь: | Exit Motor Cover |
| Парткод: | D009 4490 |
| Деталь: | Stepper Motor - DC 5.79W |
| Парткод: | D009 4547 |
| Деталь: | Tension Spring - Gate Pawl |
| Парткод: | D009 4448 |
| Деталь: | Paper Tray: No.2: Assy |
| Парткод: | D580 2900 |
| Деталь: | Link - Paper Size Sensor |
| Парткод: | B223 2910 |
| Деталь: | SPACER |
| Парткод: | B223 2911 |
| Деталь: | Decal: Paper Set Direction: Tray: No.2 |
| Парткод: | D580 2523 |
| Деталь: | Tray Bottom Plate: Assy |
| Парткод: | D089 2940 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3016 |
| Деталь: | Ground Plate - Paper Tray No.2 |
| Парткод: | B223 2919 |
| Деталь: | Cover: Paper Tray: No.2 |
| Парткод: | D580 2946 |
| Деталь: | Grip: Paper Tray |
| Парткод: | D580 2870 |
| Деталь: | Decal: Paper Tray: No.1 |
| Парткод: | D120 2872 |
| Деталь: | Decal: Paper Tray: No.2 |
| Парткод: | D120 2873 |
| Деталь: | Lever - Release Inner |
| Парткод: | B223 2862 |
| Деталь: | Tension Spring: Grip |
| Парткод: | AA06 1014 |
| Деталь: | Release Shaft |
| Парткод: | D029 2863 |
| Деталь: | Grip Holder |
| Парткод: | B223 2861 |
| Деталь: | Tension Spring: Side Fence: Rear |
| Парткод: | AA06 1003 |
| Деталь: | Lever: Release: Paper Tray: Outer |
| Парткод: | B223 2868 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | End Fence: Assy |
| Парткод: | D120 2832 |
| Деталь: | Side Fence: Front: Assy |
| Парткод: | D129 2920 |
| Деталь: | Stopper Lever - Front |
| Парткод: | D120 2924 |
| Деталь: | Spring Plate - Release Lever |
| Парткод: | B004 2923 |
| Деталь: | Plate - Side Fence Right |
| Парткод: | B223 2935 |
| Деталь: | Plate - Side Fence |
| Парткод: | B223 2934 |
| Деталь: | Gear - 16Z |
| Парткод: | B223 2936 |
| Деталь: | Rise No.1 Shaft |
| Парткод: | B223 2865 |
| Деталь: | Rise Lever |
| Парткод: | B223 2918 |
| Деталь: | Side Fence: Rear: Assy |
| Парткод: | D129 2930 |
| Деталь: | Lever: Stopper: Positioning |
| Парткод: | D120 2864 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Decal: Side Fence: Rear |
| Парткод: | D120 2875 |
| Деталь: | Seal: Tray |
| Парткод: | B180 2782 |
| Деталь: | Decal: Paper Set Direction: Tray: Right: EXP |
| Парткод: | D129 2747 |
| Деталь: | Harness - BICU-IDB |
| Парткод: | D009 5470 |
| Деталь: | PCB: IPU: Type-ISA |
| Парткод: | D129 5242 |
| Деталь: | Interface Cable: Scanner: LVDS: Assy |
| Парткод: | D129 5531 |
| Деталь: | Guide - Mother Board |
| Парткод: | D009 5877 |
| Деталь: | Harness: BCU: Image Processing Unit |
| Парткод: | D129 5446 |
| Деталь: | Harness: BCU: SIO |
| Парткод: | D129 5465 |
| Деталь: | Harness: BCU: IOB: FFC |
| Парткод: | D129 5461 |
| Деталь: | PCB: BCU: Assy |
| Парткод: | D129 5081 |
| Деталь: | Harness: Image Processing Unit: BCU: FFC: |
| Парткод: | D129 5452 |
| Деталь: | Harness - IOB-Lift Motor |
| Парткод: | D009 5495 |
| Деталь: | Harness - IOB Upper |
| Парткод: | D009 5480 |
| Деталь: | Harness - IOB-Motor |
| Парткод: | D009 5520 |
| Деталь: | PCB: IOB |
| Парткод: | D129 5157 |
| Деталь: | Harness: IOB: Lower |
| Парткод: | D129 5486 |
| Деталь: | Harness - IOB Lower Behind |
| Парткод: | D009 5490 |
| Деталь: | Bracket - IO Board |
| Парткод: | D009 5851 |
| Деталь: | Bracket - BICU |
| Парткод: | D009 5875 |
| Деталь: | Small Bracket - BICU |
| Парткод: | D009 5876 |
| Деталь: | Harness: Image Processing Unit: BCU: FFC: |
| Парткод: | D129 5453 |
| Деталь: | Frame: PCU: Upper: C2: Assy |
| Парткод: | D129 2212 |
| Деталь: | Rear Side Plate - Coupling |
| Парткод: | D009 2389 |
| Деталь: | Side Plate: Idler: Assy |
| Парткод: | D129 2390 |
| Деталь: | Electrode Plate - Charge |
| Парткод: | D009 2317 |
| Деталь: | Handle - PCU |
| Парткод: | D009 2445 |
| Деталь: | Front Side Plate - Coupling |
| Парткод: | D009 2380 |
| Деталь: | Seal: Toner Supply: Entrance: Upper |
| Парткод: | D009 2279 |
| Деталь: | Seal: Toner Supply: Entrance: Front |
| Парткод: | D009 3267 |
| Деталь: | Cap - Toner Supply |
| Парткод: | D009 2633 |
| Деталь: | Seal - Blade 13x9.5x3 |
| Парткод: | A232 2399 |
| Деталь: | Seal: Blade: Upper Rear: Small |
| Парткод: | D009 2205 |
| Деталь: | Seal: Drum: Front |
| Парткод: | D009 2201 |
| Деталь: | Seal: Drum: Entrance |
| Парткод: | D009 2203 |
| Деталь: | Seal: Drum: Rear |
| Парткод: | D009 2202 |
| Деталь: | Seal: Blade: Upper: Case |
| Парткод: | D009 2204 |
| Деталь: | Stud: Contact Point: Cleaning |
| Парткод: | B213 2316 |
| Деталь: | Electrode Plate: Charge: Front |
| Парткод: | G065 2354 |
| Деталь: | Snap Ring - M6 |
| Парткод: | G065 2681 |
| Деталь: | Front Arm - Pressure/Charge |
| Парткод: | D009 2331 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3648 |
| Деталь: | Bushing - 6x10x3 |
| Парткод: | A232 2421 |
| Деталь: | Front Bushing - Cleaning Bracket |
| Парткод: | A232 2315 |
| Деталь: | Bracket: Cleaning Blade |
| Парткод: | B213 2312 |
| Деталь: | CLEANING BLADE |
| Парткод: | D009 2351 |
| Деталь: | Spring Plate - Electrode |
| Парткод: | D009 2318 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 2348 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 2300 |
| Деталь: | Cam - Cleaning Blade |
| Парткод: | AB01 1380 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1379 |
| Деталь: | Rear Arm - Pressure/Charge |
| Парткод: | D009 2336 |
| Деталь: | Electrode Plate: Charge: Rear |
| Парткод: | G065 2308 |
| Деталь: | Terminale: Brush Roller |
| Парткод: | B082 2333 |
| Деталь: | Collar - Cleaning |
| Парткод: | A232 2318 |
| Деталь: | Seal - 24.5x68.5 |
| Парткод: | D009 2426 |
| Деталь: | Cover: Spring Plate: Front |
| Парткод: | D129 2415 |
| Деталь: | Spring Plate: Cover: PCU: Front |
| Парткод: | D009 2414 |
| Деталь: | Roller: Charge: Apply |
| Парткод: | AD02 7012 |
| Деталь: | Drum Hold Plate |
| Парткод: | D009 2303 |
| Деталь: | Screw: DIA10: M3x8 |
| Парткод: | AA14 3549 |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | A232 3553 |
| Деталь: | OPC Drum |
| Парткод: | D009 9510 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 2310 |
| Деталь: | Holder - Pick-off Pawl |
| Парткод: | A232 2340 |
| Деталь: | Pick-off Pawl |
| Парткод: | AD02 5021 |
| Деталь: | Spur |
| Парткод: | A232 2339 |
| Деталь: | Brush Roller: Cleaner: Charge: Amabuki: Assy |
| Парткод: | G790 2329 |
| Деталь: | Seal: Cover: PCU: Front |
| Парткод: | D009 2412 |
| Деталь: | Seal: Level |
| Парткод: | D009 3104 |
| Деталь: | Cover: PCU: Front: C2 |
| Парткод: | D129 2411 |
| Деталь: | Seal: Cover: Shutter |
| Парткод: | D009 2433 |
| Деталь: | Bushing - Toner Collection Coil |
| Парткод: | A232 2292 |
| Деталь: | Gear -14Z |
| Парткод: | AB01 1377 |
| Деталь: | Supporter - Left No.2 |
| Парткод: | B223 2710 |
| Деталь: | Interface Harness - BICU-LDB |
| Парткод: | D009 5475 |
| Деталь: | Supporter - Right |
| Парткод: | B223 2715 |
| Деталь: | Positioning Cap - Short |
| Парткод: | B223 2714 |
| Деталь: | CUSHION |
| Парткод: | AA16 1163 |
| Деталь: | Wire: Stopper: DIA1.5 |
| Парткод: | B223 4524 |
| Деталь: | Rubber Foot: H5 |
| Парткод: | B101 1097 |
| Деталь: | Rear Guide - Duplex Unit Set |
| Парткод: | D009 4595 |
| Деталь: | Front Guide - Duplex Unit Set |
| Парткод: | D009 4594 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3404 |
| Деталь: | Link: Stopper |
| Парткод: | D009 4512 |
| Деталь: | Bracket: Paper Feed Unit |
| Парткод: | B223 1120 |
| Деталь: | Compression Spring: Earth: Duplex Unit |
| Парткод: | D009 4513 |
| Деталь: | Grip: Front |
| Парткод: | B223 1101 |
| Деталь: | Spacer: DIA8.0: 1.5mm |
| Парткод: | D009 4511 |
| Деталь: | Stopper Bracket - Grip |
| Парткод: | D0091093 |
| Деталь: | Heat Sink: Heater: NA |
| Парткод: | B223 2702 |
| Деталь: | Heat Sink: Heater: EU |
| Парткод: | B223 2703 |
| Деталь: | Decal: Main Switch: On-standby: EU |
| Парткод: | D120 8867 |
| Деталь: | Decal: Main Switch: On-standby |
| Парткод: | D011 1252 |
| Деталь: | Cover: Harness |
| Парткод: | B223 2848 |
| Деталь: | Bracket: Cover: Harness |
| Парткод: | B223 2846 |
| Деталь: | Harness - Toner Supply Motor |
| Парткод: | D009 5505 |
| Деталь: | DC Motor: Toner Bottle: Assy |
| Парткод: | AX05 0329 |
| Деталь: | Holder: Toner Bottle: EU |
| Парткод: | B004 7667 |
| Деталь: | Guide: Toner Supply: Assy |
| Парткод: | D129 3210 |
| Деталь: | Slider Ring |
| Парткод: | A096 2065 |
| Деталь: | Interface Harness - IOB-Switch |
| Парткод: | D009 5481 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Rear Lock Lever |
| Парткод: | D009 4351 |
| Деталь: | Holder - Density Sensor |
| Парткод: | D009 3865 |
| Деталь: | DENSITY SENSOR |
| Парткод: | D009 2367 |
| Деталь: | Screw - M3 |
| Парткод: | AA14 3579 |
| Деталь: | Spur |
| Парткод: | B004 2310 |
| Деталь: | SPRING HOLDER |
| Парткод: | A232 1284 |
| Деталь: | Guide - Separation/Transport |
| Парткод: | D009 3866 |
| Деталь: | Front Lock Lever |
| Парткод: | D009 4350 |
| Деталь: | Lever - Front Upper |
| Парткод: | B238 1119 |
| Деталь: | LED Array QL Assy |
| Парткод: | B213 2362 |
| Деталь: | Harness - Quenching Lamp |
| Парткод: | D009 5510 |
| Деталь: | Entrance Sensor |
| Парткод: | AW01 0199 |
| Деталь: | Guide: Standard: Transfer Unit: Rear |
| Парткод: | D009 3856 |
| Деталь: | Guide: Standard: Transfer Unit: Front |
| Парткод: | D009 3857 |
| Деталь: | Washer: DIA3.5 |
| Парткод: | D009 4356 |
| Деталь: | Bracket - Mother Board |
| Парткод: | D009 5879 |
| Деталь: | PCB: MB |
| Парткод: | D129 5250 |
| Деталь: | Bracket: Base: SATIE |
| Парткод: | D129 5852 |
| Деталь: | Cable: HDD: SATA: Power: 2P |
| Парткод: | D129 5719 |
| Деталь: | Cable: HDD: SATA: 135 |
| Парткод: | D129 5713 |
| Деталь: | PCB: SATIE2 |
| Парткод: | D129 5710 |
| Деталь: | Bracket: HDD: Large |
| Парткод: | D129 5850 |
| Деталь: | HDD: WD: 320GB: WD3200BUCT |
| Парткод: | D124 5298 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | AA14 3848 |
| Деталь: | Rubber Cushion |
| Парткод: | AA16 1167 |
| Деталь: | Fan Motor - DC 2.16W |
| Парткод: | AX64 0195 |
| Деталь: | Guard: Fan |
| Парткод: | B154 5861 |
| Деталь: | Ground Plate- C/T Box |
| Парткод: | D009 5886 |
| Деталь: | Bracket: Main Switch |
| Парткод: | D129 5853 |
| Деталь: | Power Supply Unit: 353W: NA/TWN |
| Парткод: | AZ24 0204 |
| Деталь: | Power Supply Unit: 353W: EU/AA/CHN |
| Парткод: | AZ24 0205 |
| Деталь: | Harness: Power Supply Unit: SDSW |
| Парткод: | D129 5605 |
| Деталь: | Harness: MB: SSW |
| Парткод: | D129 5443 |
| Деталь: | Harness - Safety Switch |
| Парткод: | D009 5425 |
| Деталь: | Harness: AC: Inlet |
| Парткод: | D009 5602 |
| Деталь: | AC Harness - Heater |
| Парткод: | D009 5610 |
| Деталь: | Harness: DC Power Supply: IOB: Right |
| Парткод: | D129 5431 |
| Деталь: | Bracket - Inlet |
| Парткод: | D009 5855 |
| Деталь: | Inner Cover: Upper: Left |
| Парткод: | D129 1241 |
| Деталь: | Inner Cover: Middle |
| Парткод: | D129 1244 |
| Деталь: | Cover: Left |
| Парткод: | D129 1281 |
| Деталь: | Magnet Catch: Assy |
| Парткод: | AG07 1012 |
| Деталь: | Decal: Toner Bottle: Lock |
| Парткод: | D129 3268 |
| Деталь: | Decal: Toner Bottle: Release |
| Парткод: | D129 3269 |
| Деталь: | Cover - Shield Glass |
| Парткод: | B004 1325 |
| Деталь: | Cover: Main Switch: C3 |
| Парткод: | D129 1255 |
| Деталь: | Decal: Main Switch: On-Standby: DOM: NA |
| Парткод: | D120 8868 |
| Деталь: | Decal: Main Switch: On-standby |
| Парткод: | D011 1252 |
| Деталь: | Decal: Main Switch: O-I |
| Парткод: | D011 1251 |
| Деталь: | Decal: Main Switch: On-standby: EU |
| Парткод: | D120 8867 |
| Деталь: | Decal: Main Switch: On-Standby: CHN |
| Парткод: | D144 6849 |
| Деталь: | Inner Cover: Left |
| Парткод: | D129 1242 |
| Деталь: | Bracket: Power Supply Cord: Stay |
| Парткод: | G179 5854 |
| Деталь: | Plate: Logotype: RIC |
| Парткод: | AA00 1564 |
| Деталь: | Plate: Logotype: LAN |
| Парткод: | AA00 1565 |
| Деталь: | Plate: Logotype: GES |
| Парткод: | AA00 1567 |
| Деталь: | Sheet: Logo |
| Парткод: | D120 1551 |
| Деталь: | Model Name Plate: Aficio: 4002 |
| Парткод: | D129 6601 |
| Деталь: | Model Name Plate: Aficio: 5002 |
| Парткод: | D129 6602 |
| Деталь: | Model Name Plate: Aficio: 4002sp |
| Парткод: | D129 6603 |
| Деталь: | Model Name Plate: Aficio: 5002SP |
| Парткод: | D129 6604 |
| Деталь: | Model Name Plate: LAN: 4002: NA |
| Парткод: | D129 6629 |
| Деталь: | Model Name Plate: LAN: 5002: NA |
| Парткод: | D129 6630 |
| Деталь: | Model Name Plate: GES: 4002: AA |
| Парткод: | D129 6633 |
| Деталь: | Model Name Plate: GES: 5002: AA |
| Парткод: | D129 6634 |
| Деталь: | Model Name Plate: LAN: 5002SP: AA |
| Парткод: | D129 6635 |
| Деталь: | Model Name Plate: GES: 4002sp: AA |
| Парткод: | D129 6636 |
| Деталь: | Model Name Plate: LAN: 4002SP: AA |
| Парткод: | D129 6637 |
| Деталь: | Model Name Plate: GES: 5002SP: AA |
| Парткод: | D129 6638 |
| Деталь: | Shaft: Hinge |
| Парткод: | G179 1032 |
| Деталь: | Decal - Paper Size |
| Парткод: | B238 2524 |
| Деталь: | Cover: Front |
| Парткод: | D129 1251 |
| Деталь: | Power Cord - 230V |
| Парткод: | GZ00 0005 |
| Деталь: | MAGNET CATCH |
| Парткод: | B024 1264 |
| Деталь: | Sheet: Misfeed Removal: C1 |
| Парткод: | D129 6616 |
| Деталь: | Cover: Front Right |
| Парткод: | D129 1264 |
| Деталь: | Cloth - DF Exposure Glass |
| Парткод: | B065 1374 |
| Деталь: | Cover: Right: Rear |
| Парткод: | D129 1272 |
| Деталь: | Cover: Right: Front |
| Парткод: | D129 1271 |
| Деталь: | Decal: Misfeed Removal: B1: AL-C2 |
| Парткод: | D129 6605 |
| Деталь: | Cap: Cover |
| Парткод: | D120 1336 |
| Деталь: | Cover: Rear |
| Парткод: | D129 1293 |
| Деталь: | Cover: Rear: Upper |
| Парткод: | D129 1292 |
| Деталь: | Cover: Rear |
| Парткод: | D129 1291 |
| Деталь: | Decal: Size Indication: Paper Tray |
| Парткод: | D120 2874 |
| Деталь: | Cap: USB |
| Парткод: | D129 5891 |
| Деталь: | Cloth Holder (CHN) |
| Парткод: | B065 1371 |
| Деталь: | Holder: Exposure Glass: Ig: Assy |
| Парткод: | D144 1396 |
| Деталь: | STAMP |
| Парткод: | H511 5007 |
| Деталь: | Cover: Front Right: Upper |
| Парткод: | D129 1269 |
| Деталь: | CD-ROM: AL-C2: Drv: AA: Assy |
| Парткод: | D129 7895 |
| Деталь: | Bracket A - Left Scale |
| Парткод: | D009 1731 |
| Деталь: | Bracket: Scale: Left: B |
| Парткод: | D129 1732 |
| Деталь: | Scale: Machine Or Copier |
| Парткод: | D129 1773 |
| Деталь: | Exposure Glass: Sheet Through: 344x20 |
| Парткод: | BC01 2002 |
| Деталь: | Seal: Sheet Through |
| Парткод: | B223 1774 |
| Деталь: | Scale: Left: NA: Assy |
| Парткод: | D129 1779 |
| Деталь: | Scale: Left: EU/AA/CHN: Assy |
| Парткод: | D129 1777 |
| Деталь: | Exposure Glass |
| Парткод: | A2501752 |
| Деталь: | Optical Filter: Infrared: 76x36.5: Assy |
| Парткод: | B223 1784 |
| Деталь: | Bracket: Document Feeder: Holder |
| Парткод: | B223 1806 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 54 421 924 |
| Деталь: | Scale: Rear: Printing |
| Парткод: | D129 1782 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Scanner Home Sensor Stopper |
| Парткод: | A1931793 |
| Деталь: | Photointerruptor: Flat |
| Парткод: | AW02 0145 |
| Деталь: | Harness: SIO: Sensor |
| Парткод: | D029 5212 |
| Деталь: | Photointerruptor: Flat: PICH2mm: M4 |
| Парткод: | AW02 0146 |
| Деталь: | Document Feeder: Connector: Bracket |
| Парткод: | B2231808 |
| Деталь: | Harness: SIO: ARDF |
| Парткод: | D029 5213 |
| Деталь: | Cam: Guide Plate: Scanner: Left |
| Парткод: | B223 1116 |
| Деталь: | Seal: Exposure Glass: Rear |
| Парткод: | B2231833 |
| Деталь: | Seal: Exposure Glass |
| Парткод: | B2381845 |
| Деталь: | Seal: Guard: Exposure Glass: |
| Парткод: | D029 1774 |
| Деталь: | Paper Feed Unit: Assy |
| Парткод: | D129 2750 |
| Деталь: | Feeler: Paper End |
| Парткод: | D089 2767 |
| Деталь: | Photointerruptor: Flat |
| Парткод: | AW02 0145 |
| Деталь: | Harness - Paper Feed Unit |
| Парткод: | D029 2773 |
| Деталь: | Bracket: Sensor: Feed |
| Парткод: | D089 2778 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0128 |
| Деталь: | Bracket: Sensor |
| Парткод: | D089 2781 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0122 |
| Деталь: | DC Solenoid 24V |
| Парткод: | B223 2780 |
| Деталь: | STAY |
| Парткод: | B223 2776 |
| Деталь: | Transport Roller: Drive: Assy |
| Парткод: | D009 2757 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2143 |
| Деталь: | Harness Sheet |
| Парткод: | B223 2772 |
| Деталь: | Ground Plate - Front |
| Парткод: | B223 2786 |
| Деталь: | Paper Feed Roller: Pickup |
| Парткод: | AF03 0090 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1252 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | Guide: Feed |
| Парткод: | D089 2829 |
| Деталь: | Paper Feed Roller: Feed |
| Парткод: | AF031090 |
| Деталь: | Gear - Roller Clutch |
| Парткод: | AB01 1218 |
| Деталь: | Plain Shaft Bearing: M6 |
| Парткод: | AA08 2150 |
| Деталь: | Ground Plate - Feed |
| Парткод: | B223 2765 |
| Деталь: | Arm: Pickup |
| Парткод: | D089 2761 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0691 |
| Деталь: | Lever - Feed |
| Парткод: | G065 2767 |
| Деталь: | Gear-24z |
| Парткод: | B223 2764 |
| Деталь: | Feed Shaft |
| Парткод: | B223 2762 |
| Деталь: | Paper Feed Roller: Separate |
| Парткод: | AF03 2090 |
| Деталь: | Torque Limiter Mechanical Clutch: 40mnm: DIA18 |
| Парткод: | D129 2783 |
| Деталь: | Separate Driven Shaft |
| Парткод: | B223 2810 |
| Деталь: | Gear: Separate: Drive |
| Парткод: | AB01 0157 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0693 |
| Деталь: | PRESSURE LEVER |
| Парткод: | G065 2774 |
| Деталь: | Gear: Separate: Drive |
| Парткод: | AB01 0156 |
| Деталь: | Separate Drive Shaft |
| Парткод: | B223 2815 |
| Деталь: | Gear - 22Z |
| Парткод: | B223 2819 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Release Lever |
| Парткод: | G065 2776 |
| Деталь: | LINK LEVER |
| Парткод: | G065 2775 |
| Деталь: | Spring - Release |
| Парткод: | AA06 2259 |
| Деталь: | Upper Gate |
| Парткод: | D009 4483 |
| Деталь: | Grip: Gate Pawl: Upper |
| Парткод: | D129 4481 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | D009 4489 |
| Деталь: | Bushing - Gate |
| Парткод: | D009 4485 |
| Деталь: | Tension Spring - Duplex Gate |
| Парткод: | D009 4543 |
| Деталь: | Lever - Upper Gate |
| Парткод: | D009 4486 |
| Деталь: | Sheet - Gate |
| Парткод: | D009 4409 |
| Деталь: | Stopper - Uppergate Pawl |
| Парткод: | B223 4494 |
| Деталь: | Tension Spring: Gate Pawl: 1.6N |
| Парткод: | B223 4479 |
| Деталь: | Right Spring - Guide Plate |
| Парткод: | D009 4488 |
| Деталь: | Right Guide Plate - Open/Close |
| Парткод: | D009 4482 |
| Деталь: | Duplex Gate |
| Парткод: | D009 4577 |
| Деталь: | Tension Spring - Duplex Gate |
| Парткод: | D009 4522 |
| Деталь: | Guide Plate - Left Upper |
| Парткод: | D009 4503 |
| Деталь: | Stepper Motor DC5.06V |
| Парткод: | B2231350 |
| Деталь: | Cushion - Stepper Motor |
| Парткод: | A232 4666 |
| Деталь: | Bracket - Registration Drive Unit |
| Парткод: | D009 1151 |
| Деталь: | Timing Pulley - 27Z/40T |
| Парткод: | AB03 0744 |
| Деталь: | Timing Belt - B40S2M118 |
| Парткод: | AA04 3601 |
| Деталь: | Cover - Positioning Pin |
| Парткод: | B2381089 |
| Деталь: | Tray Cover - Right |
| Парткод: | B238 2541 |
| Деталь: | DC Motor 24V |
| Парткод: | AX04 0154 |
| Деталь: | Bracket - IO Board |
| Парткод: | D009 5851 |
| Деталь: | Bracket: Push Switch |
| Парткод: | B223 2721 |
| Деталь: | Push Switch: Paper Size Sensor |
| Парткод: | AW50 0038 |
| Деталь: | Cover - Tray Left |
| Парткод: | B238 2543 |
| Деталь: | Rubber Foot Cover |
| Парткод: | B2381066 |
| Деталь: | Harness - Development Drawer |
| Парткод: | D009 5440 |
| Деталь: | Screw - M3 |
| Парткод: | AA14 3579 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0513 |
| Деталь: | STEPPED SCREW |
| Парткод: | A859 7211 |
| Деталь: | Full Dug Point Screw: Fix: Hinge |
| Парткод: | D540 6121 |
| Деталь: | Cover: Front |
| Парткод: | D630 4411 |
| Деталь: | Decal: Display: Misfeed Removal: P1 |
| Парткод: | D630 6013 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Sound Proofing Material: Cover: Rear |
| Парткод: | B802 4712 |
| Деталь: | Cover: Rear |
| Парткод: | D630 4511 |
| Деталь: | Stay: Original Table: Contact Point |
| Парткод: | B802 2551 |
| Деталь: | Stopper: Original Table |
| Парткод: | B802 2581 |
| Деталь: | Side Fence |
| Парткод: | D630 2526 |
| Деталь: | Decal - Original Table |
| Парткод: | D578 6031 |
| Деталь: | Original Table: Face Front |
| Парткод: | D630 2522 |
| Деталь: | Slider: Side Fence |
| Парткод: | B802 2536 |
| Деталь: | Spring Plate: Side Fence |
| Парткод: | B802 2532 |
| Деталь: | Decal: Side Fence |
| Парткод: | D630 6011 |
| Деталь: | Spring Plate: 0.2T |
| Парткод: | B802 2571 |
| Деталь: | Spring Plate - Pressure Roller |
| Парткод: | A858 4676 |
| Деталь: | ROLLER DRIVEN |
| Парткод: | A858 4671 |
| Деталь: | Photo Refiection Sensor: Exit |
| Парткод: | GW01 0007 |
| Деталь: | Guide: Original Insert |
| Парткод: | D630 2541 |
| Деталь: | Harness: Sensor: Original Table |
| Парткод: | B802 5880 |
| Деталь: | Photo Refiection Sensor |
| Парткод: | AW01 0129 |
| Деталь: | Plate: Contact Point |
| Парткод: | B802 2562 |
| Деталь: | Original Table |
| Парткод: | D630 2512 |
| Деталь: | STAMP |
| Парткод: | H511 5007 |
| Деталь: | Screw: M3: DIA4X5.6 |
| Парткод: | AA14 3542 |
| Деталь: | PCU: Alex-C2: EXP: Service: Assy |
| Парткод: | D129 2110 |
| Деталь: | Rear Side Plate - Coupling |
| Парткод: | D009 2389 |
| Деталь: | Snap Ring - M6 |
| Парткод: | G065 2681 |
| Деталь: | Development Unit |
| Парткод: | D009 2301 |
| Деталь: | Developer - Black |
| Парткод: | B296 9640 |
| Деталь: | Front Cover - Development Unit |
| Парткод: | A232 3155 |
| Деталь: | Gear - 13Z |
| Парткод: | AB01 4061 |
| Деталь: | Spacer - M5 |
| Парткод: | A232 3077 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 4060 |
| Деталь: | Gear - 17Z/25Z |
| Парткод: | AB01 4062 |
| Деталь: | Front Bias Terminal |
| Парткод: | D009 3068 |
| Деталь: | Rear Bias Terminal |
| Парткод: | D009 3069 |
| Деталь: | Tape - TD Sensor |
| Парткод: | A232 3067 |
| Деталь: | Density Sensor: Development: C4 |
| Парткод: | B213 3065 |
| Деталь: | Joint- Paddle |
| Парткод: | D009 3078 |
| Деталь: | Entrance Seal - Toner Supply |
| Парткод: | D009 3066 |
| Деталь: | Seal: Side Plate: Front |
| Парткод: | D009 3205 |
| Деталь: | Shield - Development - Center |
| Парткод: | AA15 3095 |
| Деталь: | Shield: Case: Development: Front Rear: C3 |
| Парткод: | B082 3123 |
| Деталь: | Seal: Side Plate: Rear |
| Парткод: | D009 3206 |
| Деталь: | Seal - Density Sensor Harness |
| Парткод: | D009 3072 |
| Деталь: | Upper Case Seal |
| Парткод: | D009 3053 |
| Деталь: | Upper Cover - Development Unit |
| Парткод: | D009 3070 |
| Деталь: | Front Seal - Upper Cover |
| Парткод: | D009 3204 |
| Деталь: | Development Filter |
| Парткод: | D009 3086 |
| Деталь: | Ground Plate: Doctor Blade |
| Парткод: | D009 3162 |
| Деталь: | Joint: Development Sleeve: Assy |
| Парткод: | D009 1155 |
| Деталь: | Spacer: Guide Plate: 0.05 |
| Парткод: | D009 3130 |
| Деталь: | Sponge - M46 |
| Парткод: | AA15 3062 |
| Деталь: | Entrance Seal Assy |
| Парткод: | D009 3152 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Screw - M3X10 |
| Парткод: | D009 2480 |
| Деталь: | Rear Seal - Upper Cover |
| Парткод: | D009 3203 |
| Деталь: | Upper Cap - Development Case |
| Парткод: | D009 3102 |
| Деталь: | Bushing - 12x18x5.5 |
| Парткод: | AA08 0281 |
| Деталь: | Seal: Development |
| Парткод: | D009 3101 |
| Деталь: | SPONGE |
| Парткод: | D009 3106 |
| Деталь: | Seal: Slide |
| Парткод: | D009 3178 |
| Деталь: | Development Filter: Front |
| Парткод: | D009 3084 |
| Деталь: | Development Filter: Rear |
| Парткод: | D009 3085 |
| Деталь: | Operation Panel: NA: Assy |
| Парткод: | D129 1401 |
| Деталь: | Operation Panel: EU: Assy |
| Парткод: | D129 1402 |
| Деталь: | Operation Panel: AA: Assy |
| Парткод: | D129 1403 |
| Деталь: | Operation Panel: CHN: Assy |
| Парткод: | D129 1404 |
| Деталь: | Operation Panel: TWN: Assy |
| Парткод: | D129 1405 |
| Деталь: | Cover: Bracket: Operation Panel: Upper |
| Парткод: | D129 1321 |
| Деталь: | Hinge: AA-C3: Assy |
| Парткод: | D129 1530 |
| Деталь: | Bracket: Base: Hinge |
| Парткод: | D129 1517 |
| Деталь: | Cable: OPE: USB |
| Парткод: | D129 1437 |
| Деталь: | Supporting Plate: Bracket: Operation Panel |
| Парткод: | D129 1394 |
| Деталь: | Bracket: Operation Panel |
| Парткод: | D129 1396 |
| Деталь: | Cover: Bracket: Operation Panel: Lower |
| Парткод: | D129 1322 |
| Деталь: | Cover: Rear: Small |
| Парткод: | D129 1512 |
| Деталь: | Cover: Rear: Large |
| Парткод: | D129 1511 |
| Деталь: | PCB: OP-L: Assy |
| Парткод: | D129 1459 |
| Деталь: | Sheet: Keytop: Left |
| Парткод: | D129 1528 |
| Деталь: | Cable: FFC: OOL |
| Парткод: | D129 1431 |
| Деталь: | Keytop: Home |
| Парткод: | D129 1508 |
| Деталь: | Keytop: Left |
| Парткод: | D129 1509 |
| Деталь: | Stopper: Core |
| Парткод: | D009 1511 |
| Деталь: | Cable: FFC: LCD |
| Парткод: | D129 1432 |
| Деталь: | Cover: Upper: NA/AA |
| Парткод: | D129 1531 |
| Деталь: | Cover: Upper: EU/CHN/TWN |
| Парткод: | D129 1532 |
| Деталь: | Cover: Upper: CHN |
| Парткод: | D1301500 |
| Деталь: | Lens: Front |
| Парткод: | D129 1510 |
| Деталь: | Shadeing Plate: Touch Panel |
| Парткод: | D129 1513 |
| Деталь: | Touch Panel: WVGA: MV |
| Парткод: | D129 1422 |
| Деталь: | LCD Spacer B |
| Парткод: | B2381535 |
| Деталь: | LCD Spacer A |
| Парткод: | B2381534 |
| Деталь: | Keytop: 10key: NA |
| Парткод: | D129 1533 |
| Деталь: | Keytop: 10key: EU |
| Парткод: | D129 1534 |
| Деталь: | Keytop: 10key: AA |
| Парткод: | D129 1535 |
| Деталь: | LCD: TFT: WVGA: LED: SH |
| Парткод: | D129 1423 |
| Деталь: | Keytop: Stop |
| Парткод: | D129 1503 |
| Деталь: | Keytop: Start |
| Парткод: | D129 1502 |
| Деталь: | Keytop: Power Source |
| Парткод: | D129 1507 |
| Деталь: | Sheet: Keytop: Right |
| Парткод: | D129 1527 |
| Деталь: | Cable: FFC: OPR |
| Парткод: | D1291430 |
| Деталь: | PCB: OP-R: Assy |
| Парткод: | D1291458 |
| Деталь: | Sheet: OP-R |
| Парткод: | D129 1529 |
| Деталь: | Keytop: Reset Switch |
| Парткод: | D129 1506 |
| Деталь: | Bracket: LCDC: Assy |
| Парткод: | D129 1514 |
| Деталь: | Sheet: LCDC |
| Парткод: | D129 1526 |
| Деталь: | PCB: LCDC: NA: FT |
| Парткод: | D129 1441 |
| Деталь: | PCB: LCDC: EU: FT |
| Парткод: | D129 1442 |
| Деталь: | PCB: LCDC: AA/TWN: FT |
| Парткод: | D129 1443 |
| Деталь: | PCB: AL-C2: LCDC: CHN: FT |
| Парткод: | D129 1444 |
| Деталь: | Harness: Operation Sub-unit: Assy |
| Парткод: | D129 5515 |
| Деталь: | Cushion: Core |
| Парткод: | M052 1553 |
| Деталь: | Sheet: Application: Multi-language: NA |
| Парткод: | D129 1566 |
| Деталь: | Sheet: Application: Multi-language: EU |
| Парткод: | D129 1567 |
| Деталь: | Sheet: Application: Multi-language: Blank |
| Парткод: | D129 1568 |
| Деталь: | Sheet: Journal: NA/AA |
| Парткод: | D129 1536 |
| Деталь: | Harness: OPE: LVDS |
| Парткод: | D129 1435 |
| Деталь: | Gear: Z17 |
| Парткод: | B802 1671 |
| Деталь: | Gear: Z21/Z23 |
| Парткод: | B802 1661 |
| Деталь: | Gear: Z37 |
| Парткод: | B8021642 |
| Деталь: | Gear: Z26 |
| Парткод: | B8021643 |
| Деталь: | Gear: Z25 |
| Парткод: | B802 1651 |
| Деталь: | Timing Pulley: T31 |
| Парткод: | B802 1631 |
| Деталь: | Gear: Z18 |
| Парткод: | B802 1632 |
| Деталь: | Gear: Z19 |
| Парткод: | B802 1633 |
| Деталь: | Timing Belt: 40S1.5M150 |
| Парткод: | AA04 3320 |
| Деталь: | Bracket: Stepper Motor |
| Парткод: | B802 1715 |
| Деталь: | Stay: Motor: Scanning |
| Парткод: | B802 1731 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0842 |
| Деталь: | Bracket: Protect: Drive |
| Парткод: | B802 1736 |
| Деталь: | Stepper Motor: Scanning: DC 72W |
| Парткод: | D540 1721 |
| Деталь: | Gear: Z18 |
| Парткод: | B802 1681 |
| Деталь: | Timing Pulley: T31/T61 |
| Парткод: | B802 1741 |
| Деталь: | Timing Belt: 40S1.5M157.5 |
| Парткод: | AA04 3322 |
| Деталь: | Gear: Z18 |
| Парткод: | B802 1641 |
| Деталь: | Screw: Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Timing Pulley: T31: Idler: Assy |
| Парткод: | B802 1752 |
| Деталь: | Harness: Registration Sensor |
| Парткод: | B802 5810 |
| Деталь: | Bracket: Guide: Paper Feed: Lower |
| Парткод: | B802 3382 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Discharge Brush: Exit: Small |
| Парткод: | G052 4892 |
| Деталь: | Spring Plate |
| Парткод: | B802 3145 |
| Деталь: | Photo Refiection Sensor: Exit |
| Парткод: | GW01 0007 |
| Деталь: | Shielding Plate: Sensor |
| Парткод: | B802 3833 |
| Деталь: | Bracket: Registration Sensor |
| Парткод: | B802 3834 |
| Деталь: | Roller: Scanning: Entrance |
| Парткод: | B802 3231 |
| Деталь: | Roller: Scanning: Exit |
| Парткод: | B802 3251 |
| Деталь: | Timing Pulley: T33-T24 |
| Парткод: | B802 3235 |
| Деталь: | Timing Pulley: T33 |
| Парткод: | B802 3252 |
| Деталь: | Damper - Junction Gate Solenoid |
| Парткод: | A697 2102 |
| Деталь: | Timing Pulley: T33 |
| Парткод: | B802 3233 |
| Деталь: | Screw: Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Timing Pulley: T31: Idler: Assy |
| Парткод: | B802 1752 |
| Деталь: | Roller: Reverse |
| Парткод: | B802 3331 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0842 |
| Деталь: | Timing Belt: 40S1.5M378 |
| Парткод: | AA04 3321 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Pulley: Idler: DIA16: Assy |
| Парткод: | B802 1768 |
| Деталь: | Timing Pulley: T26 |
| Парткод: | B802 3312 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 2260 |
| Деталь: | Link: Solenoid |
| Парткод: | B802 3631 |
| Деталь: | Lever: Exchange Powl: Reverse |
| Парткод: | B802 3615 |
| Деталь: | Snap Ring |
| Парткод: | G020 1160 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Stay: Reverse |
| Парткод: | B802 3751 |
| Деталь: | Guide: Paper Feed: Lower |
| Парткод: | B802 3351 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | Roller: Pull Out |
| Парткод: | B802 3211 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Discharge Brush: Exit |
| Парткод: | B802 3756 |
| Деталь: | Guide: Exit: Upper |
| Парткод: | B802 3653 |
| Деталь: | Roller: Exit |
| Парткод: | B802 3311 |
| Деталь: | Cushion: Exchange Powl |
| Парткод: | B802 3612 |
| Деталь: | Exchange Powl: Reverse |
| Парткод: | B802 3611 |
| Деталь: | Timing Pulley: T23 |
| Парткод: | B802 3332 |
| Деталь: | Decal: Display: Misfeed Removal: P3 |
| Парткод: | D630 6015 |
| Деталь: | PCB: LED-DB |
| Парткод: | D129 5342 |
| Деталь: | Bracket: LED Control Board |
| Парткод: | D129 1821 |
| Деталь: | Guide: Harness: Led Control Board |
| Парткод: | D129 1803 |
| Деталь: | Pulley: Protection |
| Парткод: | D029 1749 |
| Деталь: | Pulley: DriveE Were: Front |
| Парткод: | D029 1745 |
| Деталь: | Shaft: Scanner: Drive |
| Парткод: | B1801814 |
| Деталь: | Timing Pulley 73 |
| Парткод: | G5701133 |
| Деталь: | Pulley: Drive Were: Rear: Assy |
| Парткод: | D029 1748 |
| Деталь: | Timing Belt - 157ST1.5-4.0 |
| Парткод: | B2381792 |
| Деталь: | Tension Spring: Tension: 14720mn |
| Парткод: | AA06 0979 |
| Деталь: | Stepper Motor: Assy |
| Парткод: | B1801713 |
| Деталь: | Harness: SIO: STM |
| Парткод: | D0295215 |
| Деталь: | Cover: Stepper Motor: Rear |
| Парткод: | B2231779 |
| Деталь: | Bracket: Exterior: Rear |
| Парткод: | B2231807 |
| Деталь: | PCB: SIO |
| Парткод: | D129 5138 |
| Деталь: | Harness: SIO: Scanner Unit |
| Парткод: | D089 5217 |
| Деталь: | Harness: SIO: BCU |
| Парткод: | D129 5535 |
| Деталь: | Harness: SIO: Lamp Regulator |
| Парткод: | D029 5214 |
| Деталь: | Harness: Led-db: Scnb |
| Парткод: | D129 5534 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2144 |
| Деталь: | Spacer Bushing |
| Парткод: | G570 1160 |
| Деталь: | Seal: Scanner: Frame: Base |
| Парткод: | B223 1824 |
| Деталь: | Inner Cover: Duplex: Front |
| Парткод: | D129 4534 |
| Деталь: | Inner Cover: Duplex: Rear |
| Парткод: | D129 4533 |
| Деталь: | Grip: Open And Close: Duplex Unit |
| Парткод: | D129 4579 |
| Деталь: | Stopper Hook - Duplex Unit |
| Парткод: | D009 4590 |
| Деталь: | Tension Spring - Stopper Hook |
| Парткод: | D009 4532 |
| Деталь: | Front Release Arm |
| Парткод: | D009 4537 |
| Деталь: | Rear Release Arm |
| Парткод: | D009 4538 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | D009 4664 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B223 4538 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Guide Plate: Cover: Open And Close |
| Парткод: | D129 4531 |
| Деталь: | Cover: Duplex |
| Парткод: | D129 4540 |
| Деталь: | Spring: Cover: Manual Feed |
| Парткод: | B223 2665 |
| Деталь: | Cover: Manual Feed: Entrance |
| Парткод: | D129 2664 |
| Деталь: | Sheet: Cover: Duplex |
| Парткод: | B223 4539 |
| Деталь: | Tension Spring: Wire: 180N |
| Парткод: | B223 4525 |
| Деталь: | Lever: Stopper Pawl |
| Парткод: | B802 2115 |
| Деталь: | Knob: Misfeed Removal: T27 |
| Парткод: | D6301777 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0843 |
| Деталь: | Timing Belt: 40S3M186 |
| Парткод: | B802 1774 |
| Деталь: | TAPPING SCREW |
| Парткод: | AA14 3823 |
| Деталь: | Harness: Solenoid |
| Парткод: | B802 5790 |
| Деталь: | DC Solenoid: 24V |
| Парткод: | B802 3811 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Spring: Pressure |
| Парткод: | AA06 3919 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Reverse Roller |
| Парткод: | A859 2241 |
| Деталь: | Torque Limiter Mechanical Clutch: Separator |
| Парткод: | B802 2255 |
| Деталь: | Shaft: Roller: Reverse |
| Парткод: | B802 2252 |
| Деталь: | Drum Stay: Guide: Reverse |
| Парткод: | B802 2225 |
| Деталь: | Gear: Z20 |
| Парткод: | B802 2253 |
| Деталь: | Guide: Reverse: Open And Close |
| Парткод: | B802 2228 |
| Деталь: | Decal: Display: Misfeed Removal: P2 |
| Парткод: | D630 6014 |
| Деталь: | Bushing: 6x8x5 |
| Парткод: | AA08 0265 |
| Деталь: | Roller: Reverse Exit: Driven |
| Парткод: | B802 2285 |
| Деталь: | Shaft: Reverse: Drive: Press Fit |
| Парткод: | B802 2231 |
| Деталь: | Guide: Reverse: Open And Close: Behind |
| Парткод: | B802 2227 |
| Деталь: | Cushion - Bin Solenoid Lever |
| Парткод: | A458 2251 |
| Деталь: | Stopper Pawl: Paper Feed |
| Парткод: | B802 2111 |
| Деталь: | Screw: Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Sheet: Guard |
| Парткод: | B802 2223 |
| Деталь: | Guide: Reverse: Open And Close: Sub-Assy |
| Парткод: | B802 2229 |
| Деталь: | Screw: A |
| Парткод: | AA14 3807 |
| Деталь: | Upper Guide Plate - Gate |
| Парткод: | D009 4504 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Bracket: Sensor: Entrance |
| Парткод: | B223 4566 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | D009 4664 |
| Деталь: | Tension Spring: Driven Roller |
| Парткод: | B223 4560 |
| Деталь: | Bushing: DIA4 |
| Парткод: | B223 4552 |
| Деталь: | Photointerruptor: Flat |
| Парткод: | AW02 0145 |
| Деталь: | Reverse Roller - Feed |
| Парткод: | D009 4661 |
| Деталь: | Reverse Roller Gear |
| Парткод: | AB01 4161 |
| Деталь: | Tightener |
| Парткод: | B223 4562 |
| Деталь: | SHOULDER SCREW |
| Парткод: | B044 1847 |
| Деталь: | Spring: Tightener |
| Парткод: | B223 4564 |
| Деталь: | Timing Belt: 30S2M268 |
| Парткод: | B223 4526 |
| Деталь: | Pulley: T30 |
| Парткод: | B223 4586 |
| Деталь: | Stepper Motor: DC4.29V 1.7W |
| Парткод: | B223 4572 |
| Деталь: | Rubber Bushing - 6 45hs |
| Парткод: | AA10 1021 |
| Деталь: | Bracket: Stepper Motor |
| Парткод: | B223 4575 |
| Деталь: | Gear: Pulley: Z24/T40 |
| Парткод: | B223 4571 |
| Деталь: | Timing Belt: 30S2M128 |
| Парткод: | B223 4573 |
| Деталь: | COLLAR |
| Парткод: | B044 1825 |
| Деталь: | Guide Plate: Right |
| Парткод: | B223 4501 |
| Деталь: | Harness Bracket |
| Парткод: | D009 4521 |
| Деталь: | Decal: Guide: Right |
| Парткод: | D129 4483 |
| Деталь: | Motor Harness |
| Парткод: | D009 4652 |
| Деталь: | Stay: Transport: Upper: Peen |
| Парткод: | B223 4567 |
| Деталь: | Wire Clamp |
| Парткод: | A1931766 |
| Деталь: | Clamp - Rear Wire |
| Парткод: | A1931769 |
| Деталь: | Harness: FFC: LED |
| Парткод: | D129 5541 |
| Деталь: | Carriage: No.1: Assy |
| Парткод: | D129 1721 |
| Деталь: | Clamp: MIRROR: NO.1 |
| Парткод: | M026 1815 |
| Деталь: | Mirror: No.1 |
| Парткод: | AC03 0169 |
| Деталь: | Carriage: No.2: Assy |
| Парткод: | D129 1731 |
| Деталь: | Spring Plate - 2nd Mirror |
| Парткод: | G404 2810 |
| Деталь: | Mirror: No.2: Concave: Assy |
| Парткод: | D029 1736 |
| Деталь: | Mirror: No.2: Convax: Assy |
| Парткод: | D029 1737 |
| Деталь: | PULLEY |
| Парткод: | B2381807 |
| Деталь: | Slider - Scanner |
| Парткод: | G570 2730 |
| Деталь: | Guide: FFC |
| Парткод: | M0261778 |
| Деталь: | Guide: Flat Cable |
| Парткод: | D129 1801 |
| Деталь: | 1st Slide Rail |
| Парткод: | A193 1816 |
| Деталь: | Slide Rail: No.2 |
| Парткод: | B1801734 |
| Деталь: | Idler pulley |
| Парткод: | B2381806 |
| Деталь: | Tension Spring: Tension: 11300mN |
| Парткод: | AA06 0980 |
| Деталь: | Drive Were: Carriage: DIA1.0 |
| Парткод: | D029 1747 |
| Деталь: | Bracket: Tension: Drive Wire |
| Парткод: | D089 1741 |
| Деталь: | Illumination Unit: LED: Assy |
| Парткод: | D129 1722 |
| Деталь: | Guide: FFC: Carriage: No.2 |
| Парткод: | D120 1711 |
| Деталь: | Guide: FFC: Carriage: No.1 |
| Парткод: | D120 1710 |
| Деталь: | Reflector: Scanner |
| Парткод: | D120 1705 |
| Деталь: | Carriage: No.1: Sub-assy |
| Парткод: | D120 1700 |
| Деталь: | Cover: Paper Feed |
| Парткод: | D630 4121 |
| Деталь: | Grip: Cover: Paper Feed |
| Парткод: | D630 4152 |
| Деталь: | Decal: Display: Misfeed Removal: P1 |
| Парткод: | D630 6013 |
| Деталь: | Decal: Size: Original |
| Парткод: | D578 6021 |
| Деталь: | Sound Proofing Material: Cover: Rear |
| Парткод: | B802 4712 |
| Деталь: | Hook: Grip: Cover: Front |
| Парткод: | B802 4154 |
| Деталь: | Hook: Grip: Cover: Inner Back |
| Парткод: | B802 4155 |
| Деталь: | Shaft: Grip: Cover |
| Парткод: | B802 4158 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 2262 |
| Деталь: | Bracket: Cover: Paper Feed: Front: Assy |
| Парткод: | D630 4241 |
| Деталь: | Bracket: Cover: Paper Feed: Inner Back: Ass |
| Парткод: | D630 4231 |
| Деталь: | Stopper: Cover |
| Парткод: | B802 4162 |
| Деталь: | Shaft: Cleaner |
| Парткод: | AA14 3789 |
| Деталь: | Pin: Guide Plate: Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Bracket: Paper Size Sensor |
| Парткод: | B802 4252 |
| Деталь: | Harness: Sensor: Paper Feed |
| Парткод: | D630 5870 |
| Деталь: | Photointerruptor: Entrance |
| Парткод: | AW02 0154 |
| Деталь: | Photointerruptor: Paper Size Sensor |
| Парткод: | AW02 0155 |
| Деталь: | Photo Refiection Sensor: Exit |
| Парткод: | GW01 0007 |
| Деталь: | Photo Reflection Sensor |
| Парткод: | AW01 0091 |
| Деталь: | Photointerruptor: Lg2a14nl1 |
| Парткод: | AW02 0198 |
| Деталь: | Feeler: Original Sensor |
| Парткод: | B802 4263 |
| Деталь: | Screw: MM5: 2.5MM |
| Парткод: | GA14 3003 |
| Деталь: | Cover: Upper: Paper Feed |
| Парткод: | D630 4141 |
| Деталь: | Cover: Left: Paper Feed |
| Парткод: | D630 4142 |
| Деталь: | Bracket: Cover: Paper Feed: Middle |
| Парткод: | D630 4221 |
| Деталь: | Front Heater Bracket |
| Парткод: | D009 4126 |
| Деталь: | Retaining Rings-C - Hot Roller |
| Парткод: | D009 4156 |
| Деталь: | Ball Bearing - 30x42x7 |
| Парткод: | AE03 0099 |
| Деталь: | Ball Bearing - 8x22x7 |
| Парткод: | AE03 0098 |
| Деталь: | End Ring: Spring: DIA4 |
| Парткод: | B238 4166 |
| Деталь: | Front Lever - Pressure Release |
| Парткод: | D009 4271 |
| Деталь: | Roller: Lever: Pressure |
| Парткод: | B238 4194 |
| Деталь: | Screw: Drawer |
| Парткод: | AA14 3792 |
| Деталь: | Pressure Lock Lever |
| Парткод: | D009 4274 |
| Деталь: | Tension Spring - Pressure |
| Парткод: | AA06 1024 |
| Деталь: | Front Pressure Lever |
| Парткод: | D009 4275 |
| Деталь: | Harness 1 - Thermostat |
| Парткод: | D009 4196 |
| Деталь: | Electrode Plate 3 |
| Парткод: | D009 4143 |
| Деталь: | Terminal - AC |
| Парткод: | D009 4135 |
| Деталь: | Stay: Fusing Sub-unit: Fusing Exit: Peen |
| Парткод: | D009 4152 |
| Деталь: | Tension Spring: Stripper Pawls: 50mN |
| Парткод: | AA06 0948 |
| Деталь: | Stripper Pawls |
| Парткод: | AE04 4099 |
| Деталь: | Cover: Fusing Sub-unit |
| Парткод: | D129 4165 |
| Деталь: | Harness 2 - Thermostat |
| Парткод: | D009 4197 |
| Деталь: | Housing - Thermostat |
| Парткод: | D009 4193 |
| Деталь: | Thermostat - 220C |
| Парткод: | AW11 0098 |
| Деталь: | Spacer - Thermostat |
| Парткод: | D009 4195 |
| Деталь: | Thermostat - 219C |
| Парткод: | AW11 0099 |
| Деталь: | Thermistor Bracket |
| Парткод: | D009 4178 |
| Деталь: | THERMISTOR |
| Парткод: | D009 4177 |
| Деталь: | Harness - Fusing Unit |
| Парткод: | D009 4099 |
| Деталь: | Harness: Set Sensor: TWN: C1P1 |
| Парткод: | D009 4095 |
| Деталь: | Harness - Set Sensor NA |
| Парткод: | D009 4097 |
| Деталь: | Set Sensor Harness - 230V |
| Парткод: | D009 4098 |
| Деталь: | Connector Bracket 2 |
| Парткод: | D009 4125 |
| Деталь: | Terminal cover |
| Парткод: | D009 4132 |
| Деталь: | Terminal - AC/DC |
| Парткод: | D009 4131 |
| Деталь: | ELECTRODE PLATE 2 |
| Парткод: | D009 4142 |
| Деталь: | Electrode Plate 1 |
| Парткод: | D009 4141 |
| Деталь: | Connector Bracket 1 |
| Парткод: | D009 4124 |
| Деталь: | Gear - 24Z/25Z |
| Парткод: | AB01 0172 |
| Деталь: | Bracket: Side Plate: Auxiliary |
| Парткод: | D009 4123 |
| Деталь: | Rear Heater Bracket |
| Парткод: | D009 4127 |
| Деталь: | Rear Lever - Pressure Release |
| Парткод: | D009 4291 |
| Деталь: | Front Pressure Lever |
| Парткод: | D009 4295 |
| Деталь: | Gear - 40Z |
| Парткод: | AB01 0171 |
| Деталь: | Hot Roller |
| Парткод: | AE01 1132 |
| Деталь: | Heater - 120v 550w |
| Парткод: | AX43 0112 |
| Деталь: | Heater - 230V 550W |
| Парткод: | AX43 0113 |
| Деталь: | Heater: 110V: CE |
| Парткод: | AX43 0114 |
| Деталь: | Heater - 120V 750W |
| Парткод: | AX44 0252 |
| Деталь: | Heater - 230V 750W |
| Парткод: | AX44 0253 |
| Деталь: | Heater: 110V: Si |
| Парткод: | AX44 0254 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AE02 0199 |
| Деталь: | Exit Guide - Hot Roller Unit |
| Парткод: | D009 4163 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Harness: Interface |
| Парткод: | B802 5710 |
| Деталь: | Bracket: PCB: Right |
| Парткод: | B802 1231 |
| Деталь: | Harness: Lift_Up |
| Парткод: | B802 5780 |
| Деталь: | Harness: Paper Feed |
| Парткод: | B802 5730 |
| Деталь: | Harness: Solenoid |
| Парткод: | B802 5800 |
| Деталь: | Harness: Motor: Reverse |
| Парткод: | B802 5770 |
| Деталь: | Harness: Sensor: Original Table |
| Парткод: | B802 5880 |
| Деталь: | Harness: Sensor: Paper Feed |
| Парткод: | D630 5870 |
| Деталь: | Harness: Motor: Scanning: Jst |
| Парткод: | D540 5763 |
| Деталь: | Harness: Motor: Pick Up |
| Парткод: | B802 5820 |
| Деталь: | PCB: Main Control Board: |
| Парткод: | D630 5500 |
| Деталь: | Bracket: On Off Detector |
| Парткод: | B802 1246 |
| Деталь: | Photointerruptor: Lg2a14nl1 |
| Парткод: | AW02 0198 |
| Деталь: | Bracket: PCB: Left |
| Парткод: | B802 1236 |
| Деталь: | Timing Belt: B40S2M390 |
| Парткод: | B7031165 |
| Деталь: | Bracket: Motor |
| Парткод: | B802 1612 |
| Деталь: | Screw: 6x1.7 |
| Парткод: | AA14 3802 |
| Деталь: | Bracket: Coupling |
| Парткод: | B802 1624 |
| Деталь: | Stay: Motor |
| Парткод: | B802 1616 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0842 |
| Деталь: | Stepper Motor: DC24V 4.8W |
| Парткод: | B802 1621 |
| Деталь: | Spring - Paper Size Sensor |
| Парткод: | B3871951 |
| Деталь: | Feeler: Paper Size Sensor: Pressure Plate |
| Парткод: | D6301252 |
| Деталь: | Plate: Harness: Guide |
| Парткод: | B802 1412 |
| Деталь: | Harness: Connecting: DC Fan Motor |
| Парткод: | D540 5851 |
| Деталь: | Fan: MM40x15: NIDEC: H |
| Парткод: | AX64 0202 |
| Деталь: | Bracket: Fan: Fix: 0.8mm |
| Парткод: | D540 1629 |
| Деталь: | Fusing Unit: NA: Service: Assy |
| Парткод: | D130 4002 |
| Деталь: | Fusing Unit: EU: Service: Assy |
| Парткод: | D130 4003 |
| Деталь: | Fusing Unit: TWN: Assy |
| Парткод: | D130 4004 |
| Деталь: | KNOB |
| Парткод: | D009 4244 |
| Деталь: | Exit Guide - Pressure Roller Unit |
| Парткод: | D009 4243 |
| Деталь: | Knob Bracket |
| Парткод: | D009 4248 |
| Деталь: | Compression Spring - Knob |
| Парткод: | AA06 1023 |
| Деталь: | Fusing Cover: Upper: Front |
| Парткод: | D129 4059 |
| Деталь: | Fusing Cover: Lower: Front |
| Парткод: | D129 4055 |
| Деталь: | SCREW |
| Парткод: | B223 1317 |
| Деталь: | Fusing Cover: Upper: Rear |
| Парткод: | D129 4062 |
| Деталь: | Fusing Cover: Lower: Rear |
| Парткод: | D129 4057 |
| Деталь: | Spring - Driven Roller |
| Парткод: | AA06 1022 |
| Деталь: | Bushing - Driven Roller |
| Парткод: | AA08 0352 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | D009 4664 |
| Деталь: | Bracket - Driven Roller |
| Парткод: | D009 4238 |
| Деталь: | Stay - Pressure Roller Unit |
| Парткод: | D009 4225 |
| Деталь: | Compression Spring: Cleaning Roller |
| Парткод: | AA06 1099 |
| Деталь: | Bushing - Cleaning Roller |
| Парткод: | AA08 0351 |
| Деталь: | Cleaning Roller: Assy |
| Парткод: | AE04 2098 |
| Деталь: | Fusing Cover - Duplex Guide |
| Парткод: | D009 4066 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Entrance Guide Plate - Fusing |
| Парткод: | D009 4069 |
| Деталь: | Fusing Cover: Lower: Middle: Assy |
| Парткод: | D129 4053 |
| Деталь: | Decal: H-temp Warning |
| Парткод: | D129 2705 |
| Деталь: | Guide Plate: Swivel: No.2: Assy |
| Парткод: | D129 2841 |
| Деталь: | Guide Plate: Swivel: Assy |
| Парткод: | D129 2836 |
| Деталь: | Upper Guide Plate - Registration |
| Парткод: | D009 2617 |
| Деталь: | Torsion Spring - Registration |
| Парткод: | D009 2650 |
| Деталь: | Stay - Paper Dust Removal |
| Парткод: | D009 2638 |
| Деталь: | Cover - Paper Dust Removal |
| Парткод: | D009 2618 |
| Деталь: | Bushing - Driven Registration |
| Парткод: | D009 2607 |
| Деталь: | TENSION SPRING |
| Парткод: | D009 2636 |
| Деталь: | Gear - 28Z |
| Парткод: | D009 2603 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2074 |
| Деталь: | Case Supporter - Remove Paper Dust |
| Парткод: | D009 2612 |
| Деталь: | Lower Guide Plate - Registration |
| Парткод: | D009 2624 |
| Деталь: | Registration Roller - Driven |
| Парткод: | D009 2606 |
| Деталь: | Registration Roller - Drive |
| Парткод: | D009 2600 |
| Деталь: | Gear - 16Z |
| Парткод: | B238 2655 |
| Деталь: | Gear - 18Z |
| Парткод: | D009 2602 |
| Деталь: | Knob: Registration Roller |
| Парткод: | D129 2604 |
| Деталь: | Rear Positioning Guide |
| Парткод: | D009 2623 |
| Деталь: | Harness - Registration Sensor |
| Парткод: | D009 2626 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Bracket - Registration Sensor |
| Парткод: | D009 2614 |
| Деталь: | Front Positioning Guide |
| Парткод: | D009 2622 |
| Деталь: | Rear Flange - Lock |
| Парткод: | D009 2240 |
| Деталь: | Plain Shaft Bearing: Mm8 |
| Парткод: | AA08 2158 |
| Деталь: | Shaft - Lock |
| Парткод: | D009 2243 |
| Деталь: | Cover: Stopper: Lock: PCD |
| Парткод: | D129 2245 |
| Деталь: | Stopper - Lock |
| Парткод: | D009 2244 |
| Деталь: | Front Flange - Lock |
| Парткод: | D009 2241 |
| Деталь: | Spring Plate - Lock |
| Парткод: | D009 2242 |
| Деталь: | Entrance Guide Plate - Transfer |
| Парткод: | D009 3858 |
| Деталь: | Seal: Shielding Plate |
| Парткод: | D009 3107 |
| Деталь: | Seal: Guide Plate |
| Парткод: | D009 3108 |
| Деталь: | Cleaning Blade - Transfer Belt |
| Парткод: | AD04 1135 |
| Деталь: | Bracket: Cleaning Blade: Transfer Belt |
| Парткод: | D009 3943 |
| Деталь: | Spring: Pressure: Cleaning Blade |
| Парткод: | AA06 1100 |
| Деталь: | Release Lever Shaft |
| Парткод: | D009 3919 |
| Деталь: | Retaining Rings-E |
| Парткод: | B223 6172 |
| Деталь: | Front Release Plate |
| Парткод: | D009 3920 |
| Деталь: | Rear Release Plate |
| Парткод: | D009 3921 |
| Деталь: | Front Lever - Transfer Belt |
| Парткод: | D009 3916 |
| Деталь: | Spring - Transfer Belt |
| Парткод: | AA06 3447 |
| Деталь: | Rear Lever - Transfer Belt |
| Парткод: | D009 3917 |
| Деталь: | Stopper: Blade |
| Парткод: | G102 3837 |
| Деталь: | Set Lever - Transfer Unit |
| Парткод: | D009 3899 |
| Деталь: | Release Lever |
| Парткод: | D009 3918 |
| Деталь: | Toner End Sensor |
| Парткод: | GW23 0001 |
| Деталь: | Harness - Used Toner Sensor |
| Парткод: | D009 3872 |
| Деталь: | Case - Transfer Unit |
| Парткод: | D009 3803 |
| Деталь: | Receptacle Housing - Transfer Unit |
| Парткод: | D009 3992 |
| Деталь: | SPRING |
| Парткод: | AA06 6380 |
| Деталь: | Earth Harness - Transfer Unit |
| Парткод: | D009 3876 |
| Деталь: | SPRING |
| Парткод: | AA06 6381 |
| Деталь: | Harness - Transfer Unit Bias |
| Парткод: | D009 3875 |
| Деталь: | Seal - Transfer Belt Exit |
| Парткод: | D009 3907 |
| Деталь: | Front Seal - Cleaning Blade |
| Парткод: | D009 3953 |
| Деталь: | Rear Seal - Cleaning Blade |
| Парткод: | D009 3952 |
| Деталь: | Seal - Rear Transfer Exit |
| Парткод: | D009 3906 |
| Деталь: | Shield: Remove Paper Dust |
| Парткод: | B082 3867 |
| Деталь: | Seal - Cleaning Pressure |
| Парткод: | AA15 0423 |
| Деталь: | Seal - Front Case |
| Парткод: | A232 3909 |
| Деталь: | Seal - Rear Case |
| Парткод: | A232 3908 |
| Деталь: | Decal: Positioning Display: Development |
| Парткод: | B234 3177 |
| Деталь: | Paper Feed: Unit |
| Парткод: | B802 4311 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Gear: Z19 |
| Парткод: | B802 4357 |
| Деталь: | Timing Pulley: Gear: T19/Z22 |
| Парткод: | B802 4358 |
| Деталь: | Roller: Pickup |
| Парткод: | B802 4361 |
| Деталь: | Pickup Collar |
| Парткод: | B387 2163 |
| Деталь: | Timing Pulley: T21 |
| Парткод: | B802 4372 |
| Деталь: | Timing Belt: 40S2M130 |
| Парткод: | AA04 3328 |
| Деталь: | Shaft: Pickup |
| Парткод: | B802 4352 |
| Деталь: | Bracket: Pickup |
| Парткод: | B802 4355 |
| Деталь: | Cushion: Pickup |
| Парткод: | B802 4359 |
| Деталь: | Drive Shaft - Paper Feed Belt |
| Парткод: | A859 2112 |
| Деталь: | Roller - Paper Feed Belt |
| Парткод: | B387 2113 |
| Деталь: | Spring: Belt: Paper Feed: 8N |
| Парткод: | B386 3320 |
| Деталь: | Bracket: Paper Feed Belt |
| Парткод: | B802 4333 |
| Деталь: | Collar: Shaft |
| Парткод: | B802 4326 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | SPACER |
| Парткод: | AA13 2013 |
| Деталь: | Compression Spring: Paper Feed: Joint |
| Парткод: | AA06 3435 |
| Деталь: | Bushing - 8mm |
| Парткод: | A628 1225 |
| Деталь: | Paper Feed Belt Roller |
| Парткод: | B789 2114 |
| Деталь: | Feed Belt |
| Парткод: | A8061295 |
| Деталь: | Shaft: Drive |
| Парткод: | B802 4322 |
| Деталь: | TENSION SPRING |
| Парткод: | B652 3174 |
| Деталь: | HOLDER |
| Парткод: | B802 4323 |
| Деталь: | Lever: Pickup: Release |
| Парткод: | B802 4325 |
| Деталь: | Gear: Z20 |
| Парткод: | B802 4328 |
| Деталь: | Drum Stay: Upper: Front |
| Парткод: | B802 4228 |
| Деталь: | Drum Stay: Upper: Inner Back |
| Парткод: | B802 4227 |
| Деталь: | Sheet: Guide: Upper |
| Парткод: | B802 4229 |
| Деталь: | Spring Plate: Upper |
| Парткод: | B802 4224 |
| Деталь: | Guide: Upper |
| Парткод: | B802 4222 |
| Деталь: | Bushing: DIA6 |
| Парткод: | AA08 0288 |
| Деталь: | Driven Roller: Pull Out |
| Парткод: | B802 4295 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3441 |
| Деталь: | Bracket: Driven Roller: Pull Out |
| Парткод: | B802 4282 |
| Деталь: | Ground Plate: Driven Roller: Pull Out |
| Парткод: | B802 4292 |
| Деталь: | Discharge Brush: Exit: Small |
| Парткод: | G052 4892 |
| Деталь: | GROUND PLATE |
| Парткод: | B802 4265 |
| Деталь: | Sheet: Driven Roller: Pull Out |
| Парткод: | B802 4225 |
| Деталь: | Cleaning Unit: Assy |
| Парткод: | D129 4305 |
| Деталь: | Screw - Scale |
| Парткод: | AA14 3812 |
| Деталь: | Cover: Cleaning Unit |
| Парткод: | D129 4307 |
| Деталь: | Bracket - Cleaning Unit Drive |
| Парткод: | D009 4369 |
| Деталь: | Brake pad |
| Парткод: | B065 4247 |
| Деталь: | Gear - 20Z/50Z |
| Парткод: | AB01 0174 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 0175 |
| Деталь: | SPRING |
| Парткод: | AA06 3886 |
| Деталь: | Roller clutch |
| Парткод: | D009 4355 |
| Деталь: | Holder Roller |
| Парткод: | AE04 0099 |
| Деталь: | Feeler - Web |
| Парткод: | D009 4393 |
| Деталь: | FEELER SPRING |
| Парткод: | B065 4221 |
| Деталь: | Worm Gear Shaft |
| Парткод: | D009 4378 |
| Деталь: | Bushing - 7mm |
| Парткод: | AA08 0355 |
| Деталь: | Worm Gear Bracket |
| Парткод: | D009 4377 |
| Деталь: | WORM GEAR |
| Парткод: | AB01 0178 |
| Деталь: | Gear - 32Z |
| Парткод: | AB01 0177 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0356 |
| Деталь: | Cleaning Web |
| Парткод: | AE04 5099 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0354 |
| Деталь: | Gear - 60Z |
| Парткод: | AB01 0173 |
| Деталь: | Roller clutch |
| Парткод: | D009 4388 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 0176 |
| Деталь: | Bushing - 4mm |
| Парткод: | AA08 0353 |
| Деталь: | Guide Sheet - Vertical Transport |
| Парткод: | D009 2554 |
| Деталь: | Guide Plate - Vertical Transport |
| Парткод: | D009 2563 |
| Деталь: | BUSHING - M4 |
| Парткод: | G060 2652 |
| Деталь: | Spring - 11n |
| Парткод: | B223 2676 |
| Деталь: | Holder - Vertical Transport |
| Парткод: | D009 2571 |
| Деталь: | Transport Belt: Driven: Vertical Transport |
| Парткод: | D029 2677 |
| Деталь: | Pulley - Idler |
| Парткод: | D009 2574 |
| Деталь: | Pulley - Vertical Transport |
| Парткод: | D009 2573 |
| Деталь: | Shaft - Vertical Transport |
| Парткод: | D009 2576 |
| Деталь: | Shaft - Idler |
| Парткод: | D009 2575 |
| Деталь: | Guide Plate: Feed Paper Again: Exit: Adhesio |
| Парткод: | D009 2511 |
| Деталь: | Wire: Stopper: DIA1.5 |
| Парткод: | B223 4524 |
| Деталь: | Guide Plate: Transport Unit: Exit |
| Парткод: | B223 2648 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | D009 2560 |
| Деталь: | Spring: Pressure: 5N |
| Парткод: | B223 2649 |
| Деталь: | Harness Guide |
| Парткод: | D009 4535 |
| Деталь: | Harness: Duplex Unit |
| Парткод: | D129 4651 |
| Деталь: | Pulley: DIA13 |
| Парткод: | B223 4595 |
| Деталь: | Bracket - Wire Pulley Shaft |
| Парткод: | D009 4597 |
| Деталь: | Shaft: Pulley: Wire |
| Парткод: | B223 4594 |
| Деталь: | Shaft - Duplex Unit |
| Парткод: | D009 4599 |
| Деталь: | Spring - Set Shaft |
| Парткод: | D009 4598 |
| Деталь: | Guide - Set Shaft |
| Парткод: | D009 4589 |
| Деталь: | Stopper Bracket - Spring |
| Парткод: | D009 4588 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3183 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | D009 4593 |
| Деталь: | Tension Spring - Release Bracket |
| Парткод: | D009 4587 |
| Деталь: | Spacer: Wire: Stopper |
| Парткод: | B223 4522 |
| Деталь: | Harness - High Voltage Cable |
| Парткод: | D009 5420 |
| Деталь: | Power Pack: CBT |
| Парткод: | AZ320177 |
| Деталь: | Bracket - Power Pack |
| Парткод: | D009 5854 |
| Деталь: | Brushless Motor: Drive: Drum: DC 10W |
| Парткод: | AX06 0415 |
| Деталь: | Brushless Motor - DC 11W |
| Парткод: | AX06 0355 |
| Деталь: | Rear Drive Bracket - Engine |
| Парткод: | D009 1120 |
| Деталь: | Ball Bearing - 8x22x7 |
| Парткод: | B242 1161 |
| Деталь: | Ground Plate - Drum |
| Парткод: | D009 1121 |
| Деталь: | Gear: Drum |
| Парткод: | AB01 0379 |
| Деталь: | Drive Unit- Transfer On-Off |
| Парткод: | D009 1113 |
| Деталь: | Drive Bracket - Transfer |
| Парткод: | D009 1123 |
| Деталь: | Gear - 27TZ/42Z |
| Парткод: | AB01 7752 |
| Деталь: | Collar - 6x18.8mm |
| Парткод: | D009 1148 |
| Деталь: | Pulley - 31T |
| Парткод: | AB03 0821 |
| Деталь: | Gear - 46Z |
| Парткод: | AB01 0141 |
| Деталь: | Pulley - 31T |
| Парткод: | AB03 0820 |
| Деталь: | Parallel Pin - 2x12mm |
| Парткод: | AA14 5294 |
| Деталь: | Ground Plate - Drum |
| Парткод: | D009 1141 |
| Деталь: | Drum Shaft Holder |
| Парткод: | D009 1145 |
| Деталь: | Joint: Development Sleeve: Assy |
| Парткод: | D009 1155 |
| Деталь: | Terminal - Development Roller |
| Парткод: | D009 1147 |
| Деталь: | Spring - Intermediate Drawer |
| Парткод: | AA06 3432 |
| Деталь: | Drum Shaft |
| Парткод: | D009 1111 |
| Деталь: | Front Drive Bracket - Engine |
| Парткод: | D009 1139 |
| Деталь: | Gear - 90Z |
| Парткод: | AB01 0140 |
| Деталь: | Pulley - 48T/90T |
| Парткод: | D0091142 |
| Деталь: | Timing Belt - 60S2M300 |
| Парткод: | AA04 3658 |
| Деталь: | Roller - Tightener |
| Парткод: | D0091127 |
| Деталь: | Spring - Tightener |
| Парткод: | D009 1128 |
| Деталь: | Tightener Bracket - Development |
| Парткод: | D0091135 |
| Деталь: | Tightener Bracket - Transfer |
| Парткод: | D0091125 |
| Деталь: | Plate - Optical Housing Unit |
| Парткод: | B004 1936 |
| Деталь: | Receptacle Housing - Transfer |
| Парткод: | D009 3831 |
| Деталь: | Receptacle Terminal - Transfer |
| Парткод: | D009 3832 |
Коды ошибок
101
120
121
141
142
143
144
161
162
165
202
203
204
220
221
230
231
240
270
302
304
320
324
350
351
355
360
372
396
400
440
441
442
501
502
503-1
503-2
504-1
504-2
505-1
505-2
530
531
532
533
540
541
542
543
544
545
547
551
552
553
554
555
557
559
610
620-01
620-02
621
622
623
630
632
633
634
635
636-01
636-02
636-11
636-99
637-01
637-02
641
650-001
650-004
650-005
650-013
650-014
651-001
651-002
652
653
669
670
672
674
687
700-01
700-02
700-12
701-02
701-03
720-24
720-25
720-30
720-41
720-42
720-43
720-44
720-52
720-53
720-55
720-57
720-60
720-61
720-70
720-71
720-72
720-73
720-74
720-75
720-80
720-81
722-10
722-14
722-17
722-24
722-30
722-41
722-42
722-44
722-70
722-71
770
791
792
816
817
818
819
820
821
822
823
824
826
827
828
829
833
835
838
839
840
841
842
851
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
870
872
873
874
875
876
877
878
880
881
899
900
920
921
925
990
991
992
994
995
997
998
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 141 |
| Display: | SVC 141 ERROR |
| Description: | Motor |
| Causes: | • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor excessive PWM - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board” |
| Error code: | 142 |
| Display: | Contact the Service center. 142: Error |
| Description: | Motor |
| Causes: | • Standard white plate defective, dirty • Moisture inside the scanner unit • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor, over speed - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”. |
| Error code: | 143 |
| Display: | Service Call 143:Error |
| Description: | Motor |
| Causes: | • SBU defective • IPU defective • BCU defective • Harness between the SBU and IPU defective • Harness between the BCU-IPU defective • Standard white plate not installed correctly, or is dirty • Scanner mirrors and/or lenses are dirty or installed incorrectly |
| Remedy: | DC pick motor, no encoder feedback - staging motor - replace the “Staging motor” on page 4-79. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 161 |
| Display: | SYSTEM HALT (*) 161 : PCB MAIN-F6 |
| Description: | IPU Error At power on, or when the machine returns from an energy save mode, the self-diagnostic program returned an IPU error. |
| Causes: | • IPU defective • Connection between SBU and IPU is loose, broken, or defective |
| Error code: | 162 |
| Description: | Motor |
| Causes: | Defective IPU Defective BCU |
| Remedy: | Black cartridge BLDC motor mfg. unknown - go to “162 error code” on page 2-65. |
| Error code: | 165 |
| Description: | Out of Paper; Load Tray 1 (MPT) with [size] [type] The Tray 1 (MPT) No Paper Sensor indicates Tray 1 (MPT) is empty. |
| Causes: | • No Paper Sensor, PL5.3.14 • No Paper Sensor Actuator, PL5.3.15 • FRONT/DUP Harness, PL5.3.28 |
| Remedy: | 1 Fill Tray 1 (MPT) with paper. Does the error persist? Go to Step 2. Complete. 2 Check the following for evidence of fault or damage: • Tray 1 (MPT) No Paper Sensor, PL5.3.14 • Sensor Actuator, PL5.3.15 Is there any damage? Replace any damaged parts. Go to Step 3. 3 Test the Tray 1 (MPT) No Paper Sensor. Run the Service Diagnostics Tray 1 (MPT) No Paper Sensor test. Does the sensor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the Tray 1 (MPT) No Paper Sensor signal. Is there +3.3 V across P/J135-1 <=> P/J135-2? Replace the sensor. Go to Step 5. 5 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J135. 2. Check continuity between J13 <=> J134. Replace the Engine Control Board. Replace the FRONT/DUP Harness. |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 204 |
| Display: | Power OFF/ON 204:Error |
| Description: | Polygon motor error 3: XSCRDY signal error |
| Causes: | The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing. |
| Remedy: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board). |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 221 |
| Description: | Laser synchronizing detection error: start position [K]: LD1 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 231 |
| Display: | Service Call 231: Error |
| Description: | FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 240 |
| Display: | Service call 240: Error |
| Description: | LD error |
| Causes: | The IPU (EGB) detects a problem at the LD unit. |
| Remedy: | • Worn-out LD • Disconnected or broken harness of the LD. 1. Replace the laser optics unit. |
| Error code: | 270 |
| Description: | GAVD communication error On startup, Read/Write performed for the same register does not match. |
| Causes: | Defective GAVD. Defective eSOC. Defective BCU. Defective harness. |
| Remedy: | • Turn the main power switch off and on. • Replace the laser optics-housing unit. • Replace the BCU. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 304 |
| Display: | ERROR 304 USB INIT ERR |
| Description: | Charge AC bias error [K] The charge current less than 200 mkA is detected. |
| Causes: | Defective charge roller. Defective connectors. Disconnected harness. Defective high voltage power 1. |
| Remedy: | 1. Check the connectors. 2. Replace the PCU for black. 3. Replace the drum positioning plate. |
| Error code: | 320 |
| Display: | Reset fuser 320: Fuser error |
| Description: | Same unit not detected upon power ON or opening cover. |
| Causes: | 1) Is error message displayed? 2) Is fuser unit set properly? 3) Does error reoccur? |
| Remedy: | Check if fuser is set properly. Reset fuser and turn ON power again. Replace fuser unit assembly. |
| Error code: | 324 |
| Display: | Open/close cover 324: Paper thickness error |
| Description: | Sensor output gap out of range with no media. (Only for Factory Mode) |
| Causes: | 1) Are foreign objects mixed in sensor? 2) Does printer recover when detecting paper thickness by opening/closing tray? 3) Does printer recover by power OFF/ON. |
| Remedy: | Remove foreign objects. Normal. |
| Error code: | 350 |
| Description: | ID sensor error 1 One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. Vsp greater than or equals 2.5V Vsg less than 2.5 Vsp = 0V Vsg = 0 |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 351 |
| Description: | ID sensor error 2 The ID sensor output voltage is 5.0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 355 |
| Display: | Set new belt 355: Belt life |
| Description: | Belt life notified (alarm). Print N-count by opening and closing cover. |
| Causes: | Right after replacing belt? |
| Remedy: | Check belt life. Replace belt. |
| Error code: | 360 |
| Display: | Set duplex unit 360: Duplex unit is open. |
| Description: | When duplex unit is removed from printer. |
| Causes: | Does error recover by resetting duplex unit? |
| Remedy: | Normal. Replace duplex unit or engine board. |
| Error code: | 372 |
| Display: | Check DUPLEX 372: Paper jam |
| Causes: | Check miss-feed in duplex unit. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace duplex unit. |
| Error code: | 396 |
| Description: | Black drum motor error |
| Causes: | The LOCK signal error is detected when the EGB monitors the black drum motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the black drum motor. Replace it if necessary.e hig |
| Error code: | 400 |
| Display: | Open top cover 400: Paper size error |
| Description: | TM sensor error |
| Causes: | The CPU detected a low voltage of the positive reflection output under the threshold in the TM sensor. |
| Remedy: | • TM sensors are dirty. • A solid print out due to an electrostatic charging error • The TM sensor is defective. 1. Clean the TM sensors. 2. Replace the TM sensors. 3. Check the image transfer unit. 4. Turn the power Off and On. |
| Error code: | 440 |
| Description: | Transfer Output Error. A high voltage feedback voltage of less than 0.5 V was detected for 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 441 |
| Description: | Image transfer unit motor error When the motor is ON, the machine monitors the lock signals every 100 ms. If the High status occurs 20 times consecutively, the machine judges that the motor is not rotating correctly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Shorted 24 V fuse on the PSU. Defective interlock systeme PSU. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system |
| Error code: | 442 |
| Description: | Image transfer belt contact motor error The image transfer belt contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates. |
| Causes: | Motor overload. Defective motor. Loose connection. Disconnected harness. Shorted 24 V fuse on the PSU. Defective interlock system. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Replace the interlock switch. • Replace the IOB. |
| Error code: | 501 |
| Display: | Service Call 501: Error |
| Description: | Tray 1 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503-1 |
| Description: | 3rd tray lift malfunction (optional paper feed unit or LCT) For the paper feed unit: • SC 503-01 occurs if the lift sensor does not turn on within 10 seconds after the tray lift motor has turned on. For the LCT: • SC 503-01 occurs if the lift sensor does not turn on or turn off within 8 seconds after the tray lift motor has turned on to lift or lower the tray.For the paper feed unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection • Defective upper limit sensor or connector disconnection • Defective tray lift motor or connector disconnection |
| Causes: | For the paper feed unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection • Defective upper limit sensor or connector disconnection • Defective tray lift motor or connector disconnection |
| Error code: | 503-2 |
| Description: | 3rd tray lift malfunction (optional paper feed unit or LCT) For the paper feed unit: • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. For the LCT: • When the main switch is turned on or when the LCT is set, if the end fence is not in its position (home position sensor ON), the tray lift motor stops. • If the upper limit does not go off for 1.5 seconds even the tray lift moto |
| Causes: | For the paper feed unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection |
| Error code: | 504-1 |
| Description: | 4th tray lift malfunction (optional paper feed unit) For the paper feed unit: • When the tray lift motor turns on, the upper limit is not detected within 10 seconds. If this condition occurs three consecutive times, the SC is generated. |
| Causes: | For the paper feed unit:• Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection |
| Error code: | 504-2 |
| Description: | 4th tray lift malfunction (optional paper feed unit) For the paper feed unit: When the tray lift motor is turned on, the upper limit is not detected within 10 seconds. If this condition occurs three consecutive times, the SC is generated. |
| Causes: | • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection |
| Error code: | 505-1 |
| Description: | 5th tray lift malfunction (optional LCT) This SC is generated if the following condition occurs: • When the tray lift sensor of the LCT 1200-sheet does not go on after the tray lift motor has turned on to lift the paper tray. • When the tray lift sensor of the LCT 1200-sheet does not go off after the tray lift motor has turned on to lower the paper tray. • When the tray lift sensor of the LCT 1200-sheet does not go on after the pickup roller solenoid has turned on at power on. |
| Causes: | • Tray lift motor defective or disconnected • Tray lift sensor defective or disconnected |
| Remedy: | 1. Check the harness connections. 2. Replace the tray lift motor. 3. Replace the tray lift sensor. |
| Error code: | 505-2 |
| Description: | 5th tray lift malfunction (optional LCT) Both tray lift sensor and lower limit sensor are turned on at the same time when the main power is turned on or the right door is closed. |
| Causes: | • Tray lift motor defective or disconnected • Tray lift sensor defective or disconnected • Lowe limit sensor defective or disconnected |
| Remedy: | 1. Check the harness connections. 2. Replace the tray lift motor. 3. Replace the tray lift sensor. 4. Replace the lower limit sensor. |
| Error code: | 530 |
| Description: | LSU Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the LSU fan motor. |
| Error code: | 531 |
| Description: | Fusing Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the fusing fan motor. |
| Error code: | 532 |
| Description: | IH coil fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH coil fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH coil fan motor • Defective IH coil fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH coil fan. 3. Replace the IOB. |
| Error code: | 533 |
| Description: | IH inverter fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH inverter fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH inverter fan motor • Defective IH inverter fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH inverter fan. 3. Replace the IOB. |
| Error code: | 540 |
| Description: | Fusing/Paper exit motor error At the fusing delivery brushless motor, the lock signal is monitored every 100 ms. If the High status occurs consecutively 20 times, it is determined as a failure to rotate properly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Shorted 24 V fuse on the PSU. Defective interlock system. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 554 |
| Description: | Fusing sleeve belt overheat: End (hardware error) The fusing sleeve belt thermistor detects 250°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 555 |
| Description: | Fusing Heater error: End The fusing heater keeps full power for 9 seconds or more. |
| Causes: | Defective thermistors. Broken heater cables. |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 610 |
| Display: | ERROR 610 NOT FILLUP |
| Description: | Mechanical counter error: Bk This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 620-01 |
| Description: | BCU-ADF Communication Error: Break RX abnormal A BREAK was detected after connection. |
| Causes: | • ADF I/F cable connection loose, broken, defective • ADF control board defective • BCU defective • Serial line level unstable • External noise on the line |
| Remedy: | • Check if all connectors related to ADF are connected securely. Reconnect the connectors if they are disconnected, or loose. • Check for the existence of noise or software bugs in the machine and ADF firmware. Run the firmware update when a new firmware is released. • Check the harness. Replace the harness if it is disconnected, or damaged. • Check for MPU malfunction and replace the MPU if any abnormalities exist. • Check if there are any signs of a short circuit on the ADF Main Board. If there are any defects, replace the board. |
| Error code: | 620-02 |
| Description: | ADF communication error: Communication error between IPU and ADF After the ARDF is detected, the break signal occurs or communication timeout occurs. |
| Causes: | Incorrect installation of ARDF ARDF defective |
| Remedy: | • Do not use an incompatible ADF. Replace it with a compatible ADF. • Perform the same recovery procedures as the SC620-01 if there is recurrence when using a compatible ADF. |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 622 |
| Description: | Paper Bank communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The paper bank`s control board is faulty. Defective BCU/IOB. The paper bank`s connection is faulty. |
| Remedy: | • Reconnect the paper bank cables. • Replace the BCU. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 623 |
| Description: | 2nd Paper Bank communication error An error code is issued from the paper bank unit. |
| Causes: | Loose connection. Defective paper bank. |
| Remedy: | • Reconnect the connector. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 630 |
| Description: | CSS communication error A communication error occurred during communication with the CSS. |
| Causes: | • Communication line error |
| Remedy: | Logging only. |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 633 |
| Description: | Key/card counter device error 2 During communication with the device, the MCU received a break (Low) signal. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 636-01 |
| Description: | SD Card Error. Expanded authentication module error There is no expanded authentication module in the machine. The SD card or the file of the expanded authentication module is broken. There is no DESS module in the machine. |
| Causes: | • No expanded authentication module • Defective SD card • No DESS module |
| Remedy: | 1. Install the expanded authentication module. 2. Install the SD card. 3. Install the DESS module. |
| Error code: | 636-02 |
| Description: | IC card error When the version of the expanded authentication module is not correct. |
| Causes: | The version of the expanded authentication module is not correct. |
| Remedy: | Install the correct expanded authentication module. |
| Error code: | 636-11 |
| Description: | SD Card Error. OSM user code file error |
| Causes: | The correct "usercode" file could not be found in the root folder of the SD card because the file is not present, or the existing file is corrupted or the wrong type file. |
| Remedy: | Create the usercode files with the User Setting Tool "IDissuer.exe" and store the files in the root folder of the SD card. • Make sure the eccm.mod file is in the root folder of the SD card. |
| Error code: | 636-99 |
| Description: | IC Card Error: Management area error The management number of the external authentication module exceeds the maximum limit. |
| Causes: | • Software error |
| Error code: | 637-01 |
| Description: | Tracking Information notification Error (Tracking application error) Tracking information was lost. |
| Causes: | • Tracking SDK application error • Internal notification error |
| Remedy: | Cycle the main power off and on. |
| Error code: | 637-02 |
| Description: | Tracking Information notification Error (Management server error) Tracking information was lost. |
| Causes: | Communication with tracking management server failed. • Network error • tracking management server error • Tracking SDK application error |
| Remedy: | Cycle the main power off and on. |
| Error code: | 641 |
| Description: | BICU control data transfer abnormal A sampling of the control data sent from the BICU reveals an abnormality. |
| Causes: | • Defective controller board • External noise • Defective BCU |
| Remedy: | 1. Replace the controller board. 2. Replace the BCU. |
| Error code: | 650-001 |
| Description: | Communication error of the remote service modem (Embedded RCG-M): Authentication error The authentication for the Embedded RCG-M fails at a dial up connection. |
| Causes: | • Incorrect SP settings • Disconnected telephone line • Disconnected modem board Check and set the correct user name (SP5816-156) and password (SP5816-157). |
| Error code: | 650-004 |
| Description: | Communication error of the remote service modem (Embedded RCG-M): Incorrect modem setting Dial up fails due to the incorrect modem setting. |
| Causes: | • Same as -001 Check and set the correct AT command (SP5816-160). |
| Error code: | 650-005 |
| Description: | Communication error of the remote service modem (Embedded RCG-M): Communication line error The supplied voltage is not sufficient due to a defective communication line or defective connection. |
| Causes: | • Same as -001 Consult with the user`s local telephone company. |
| Error code: | 650-013 |
| Description: | Communication error of the remote service modem (Embedded RCG-M): Modem board error 1 The modem board does not work properly even though the setting of the modem board is installed with a dial up connection. |
| Causes: | Same as -001 1. Install the modem board. 2. Check and reset the modem board setting with SP5816. 3. Replace the modem board |
| Error code: | 650-014 |
| Description: | Communication error of the remote service modem (Embedded RCG-M): Modem board error 2 The modem board is installed even though the RCG-N is installed. |
| Causes: | 1. Uninstall the modem board, if it is installed. 2. Check that the Wireless LAN or Ethernet LAN is working properly. |
| Error code: | 651-001 |
| Description: | Incorrect dial up connection: Program parameter error An unexpected error occurs when the modem (Embedded RCG-M) tries to call the center with a dial up connection. |
| Causes: | • Caused by a software bug |
| Error code: | 651-002 |
| Description: | Incorrect dial up connection: Program execution error An unexpected error occurs when the modem (Embedded RCG-M) tries to call the center with a dial up connection. |
| Causes: | • Caused by a software bug |
| Error code: | 652 |
| Description: | Remote service ID2 mismatching ID2 for @Remote certification is mismatching between the controller board and NVRAM. Used controller board installed. Used NVRAM installed An unexpected error occurs when the modem (Embedded RCG-M) tries to call the center with a dial up connection. |
| Causes: | If this occurs during the @Remote installation • Check the NVRAM`s validity and serial number, write the common certificate, and then retry the installation. If this occurs after the @Remote installation • Clear the current @Remote setting, check the NVRAM`s validity and serial number, write the common certificate, and then retry the installation. |
| Error code: | 653 |
| Description: | Incorrect remote service ID2 If one of the following applies to the ID2 recorded in the NVRAM: • The character string is not 17 characters long. • Unprintable characters are included. • It contains spaces only. • It is blank. |
| Remedy: | • Replace the NVRAM • Clear the current @Remote setting, write the common certificate, and then retry the installation. |
| Error code: | 669 |
| Description: | EEPROM Error |
| Causes: | An unexpected value exists in the initialization flag of the EEPROM |
| Remedy: | • EEPROM not initialized • Defective EEPROM |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 674 |
| Description: | Transmission error in controller board Video transmission error is detected in the controller board. |
| Causes: | Defective Controller Board |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 700-01 |
| Description: | ADF original table lift malfunction One of the following conditions was detected. • The bottom plate position sensor does not activate when the bottom plate motor lifts the original table. • The bottom plate HP sensor does not activate when the bottom plate motor lowers the original table. |
| Causes: | • Loose, broken or defective harnesses, connectors of the bottom plate position sensor, bottom plate HP sensor, bottom plate motor • Defective bottom plate position sensor • Defective bottom plate HP sensor • Defective bottom plate motor • Defective ADF main control board |
| Remedy: | Bottom plate motor rotation: 1. Check or replace the bottom plate position sensor. 2. Check or replace the bottom plate HP sensor. No bottom plate motor rotation: 1. Replace the bottom plate motor. 2. Replace the ADF main control board. |
| Error code: | 700-02 |
| Description: | Original pick-up HP error When the pick-up motor turns on clockwise, the original pick-up HP sensor does not detect the home position of the original calling. |
| Causes: | • Defective original pick-up HP sensor • Defective pick-up motor • Defective DF drive board |
| Remedy: | 1. Replace the DF drive board if the pick-up motor does not work correctly. 2. Replace the pick-up motor. 3. Replace the original pick-up HP sensor. |
| Error code: | 700-12 |
| Description: | DF fan error DF fan motor lock signal is detected after original transportation has finished. |
| Causes: | • DF fan motor dirty • Disconnected or broken harnesses • Defective DF fan motor |
| Remedy: | 1. Clean the DF fan motor. 2. Check or replace the harness with the DF fan motor. 3. Replace the DF fan motor.. |
| Error code: | 701-02 |
| Description: | Scanner feeding error 2: Pick-up motor driver error The error flag of the pick-up motor driver IC is asserted when the jam error is issued. |
| Causes: | Pick-up motor driver detected an error. |
| Error code: | 701-03 |
| Description: | Scanner feeding error 2: Paper feed motor error The error flag of the paper feed motor driver IC is asserted when the jam error is issued. |
| Causes: | Pick-up motor driver detected an error. |
| Error code: | 720-24 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | Guide plate motor disconnected, defective. Guide plate motor overloaded due to obstruction. Guide plate position sensor disconnected, defectivelay. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-25 |
| Description: | Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | Punch HP sensor disconnected, defective. Punch motor disconnected or defective. Punch motor overload due to obstruction. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-30 |
| Description: | Finisher jogger motor error The jogger fences move out of the home position but the HP sensor output does not change within the specified number of pulses. The 1st failure issues an original jam message, and the 2nd failure issues this SC code. |
| Causes: | Jogger HP sensor disconnected, defective. Jogger motor disconnected, defective. Jogger motor overloaded due to obstruction. Finisher main board and jogger motor. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-41 |
| Description: | Stack feed-out motor error The stack feed-out HP sensor does not detect the home position of the stack feed-out belt within the specified time after the stack feed-out belt has moved to its home position. The stack feed-out HP sensor does not turn off 200 ms after the stack feed-out belt has moved from its home position. The 1st detection failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | Defective motor. HP sensor disconnected, defective. Motor harness disconnected, loose, defective. Motor overload. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-42 |
| Description: | Finisher stapler movement motor error The stapler does not return to its home position within the specified time after stapling. The 1st detection failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | Motor overload. Loose connection of the stapler home position sensor. Loose connection of the stapler movement motor. Defective stapler home position sensor. Defective stapler movement motor. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-43 |
| Description: | Finisher corner stapler rotation motor error The stapler does not return to its home position within the specified time after stapling. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | Defective stapler rotation motor. Loose connection of the finisher corner stapler rotation motor. Overload to the stapler rotation motor. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-44 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. Staple movement is not finished after a certain time. |
| Causes: | Staple jam. Loose connection. An overload has occurred due to staples applied to sheets exceeding the maximum number. Defective home position sensor. Defective stapler motor. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-52 |
| Description: | Finisher folder plate motor error The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | Folder plate HP sensor disconnected, defective. Folder plate motor disconnected, defective. Folder plate motor overloaded due to obstruction. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-53 |
| Description: | Fold unit bottom fence motor error The bottom fence of the fold unit moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | Motor harness disconnected, loose, defective. Motor overload. Defective motor. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-55 |
| Description: | Clamp roller retraction motor error The clamp roller retraction motor moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | Defective motor. Loose connection. Motor overload. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-57 |
| Description: | Stack junction gate motor error The stack junction gate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | Defective motor. Loose connection. Motor overload. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-60 |
| Description: | Booklet stapler motor error 1 The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The front stapler unit saddle-stitch motor does not start operation within the specified time. |
| Causes: | Staple jam. Defective motor. Loose connection. An overload has occurred due to staples applied to sheets exceeding the maximum number. Defective home position sensor. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-61 |
| Description: | Booklet staple motor error 2 The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The rear stapler unit saddle-stitch motor does not start operation within the specified time. |
| Causes: | Staple jam. Defective motor. Disconnected connector. An overload has occurred due to staples applied to sheets exceeding the maximum number. Defective home position sensor. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-70 |
| Description: | Tray lift motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. |
| Causes: | Defective motor. Loose connection. Motor overload. Defective upper tray paper height sensor. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-71 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | Defective motor. Loose connection. Motor overload. Defective home position sensor. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-72 |
| Description: | Exit jogger motor 1 error The Exit jogger motor 1 moves but is not detected at the home position within the specified time. The 1st detection failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | Exit jogger motor sensor disconnected, defective. Exit jogger motor is disconnected, defective. Exit jogger motor overloaded due to obstruction. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-73 |
| Description: | Exit jogger motor 2 error The Exit jogger motor 2 moves but is not detected at the home position within the specified time. The 1st detection failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | Exit jogger motor sensor disconnected, defective. Exit jogger motor is disconnected, defective. Exit jogger motor overloaded due to obstruction. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-74 |
| Description: | Exit jogger evacuate motor error The Exit jogger evacuate motor moves but is not detected at the home position within the specified time. The 1st detection failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | Exit jogger evacuate motor sensor disconnected, defective. Exit jogger evacuate motor is disconnected, defective. Exit jogger evacuate motor overloaded due to obstruction. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-75 |
| Description: | Stacking sponge roller motor Occurs during the operation of the stacking sponge roller motor. |
| Causes: | Defective motor. Motor harness disconnected, loose, defective Motor overloaded. Defective stacking roller HP sensor. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-80 |
| Description: | Punch movement motor error The punch unit moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | Defective motor. Motor harness disconnected, loose, defective. Motor overloaded. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720-81 |
| Description: | Paper position sensor slide motor error The paper position sensor moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | Defective motor. Disconnected, loose or defective harness. Motor overloaded. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 722-10 |
| Description: | 1000-Sheet Finisher Error. Upper transport motor error The upper transport motor in the finisher is not operating. |
| Causes: | • The motor harness is loose or broken • Upper transport motor disconnected, defective • Upper transport motor overloaded due to obstruction (jammed paper, paper scraps, etc.) |
| Error code: | 722-14 |
| Description: | 1000-Sheet Finisher Error. Lower transport motor error The lower transport motor in the finisher is not operating. |
| Causes: | • The motor harness is loose or broken • Lower transport motor disconnected, defective • Lower transport motor drive overloaded due to obstruction (jammed paper, paper scraps, etc.) |
| Error code: | 722-17 |
| Description: | 1000-Sheet Finisher Error. Exit motor error The exit motor in the finisher is not operating. |
| Causes: | • The motor harness is loose or broken • Exit motor disconnected, defective • Exit motor drive overloaded due to obstruction (jammed paper, paper scraps, etc.) |
| Error code: | 722-24 |
| Description: | 1000-Sheet Finisher Error. Finisher exit guide plate motor error • The exit guide plate HP sensor does not detect the home position of the exit guide plate within the prescribed time after the exit guide plate has moved to its home position. • The exit guide plate HP sensor does not turn off within the prescribed time after the exit guide plate has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Exit guide plate motor harness loose, broken • Exit guide plate HP sensor harness loose, broken • Exit guide plate motor disconnected, defective • Exit guide plate HP sensor disconnected, defective • Finisher exit guide plate motor drive overloaded due to obstruction (jammed paper, paper scraps, etc.) |
| Error code: | 722-30 |
| Description: | 1000-Sheet Finisher Error. Jogger fence motor error • The jogger HP sensor does not detect the home position of the jogger fences within the prescribed time after the jogger fences have moved to its home position. • The jogger HP sensor does not turn off within the prescribed time after the jogger fences have moved from its home position. The 1st failure issues an original jam message, and the 2nd failure issues this SC code. |
| Causes: | • The motor harness is loose or broken • Jogger fence HP sensor harness loose, broken • Jogger fence motor disconnected, defective • Jogger fence HP sensor disconnected, defective • Jogger motor drive overloaded due to obstruction (jammed paper, paper scraps, etc.) |
| Error code: | 722-41 |
| Description: | 1000-Sheet Finisher Error. Feed-out belt motor error • The feed-out HP sensor does not detect the home position of the feed-out belt within the prescribed time after the feed-out belt has moved to its home position. • The feed-out HP sensor does not turn off within the prescribed time after the feedout belt has moved from its home position. The 1st detection failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | • Feed-out belt motor harness loose or broken • Feed-out belt HP sensor harness loose or broken • Feed-out belt motor disconnected, defective • Feed-out belt HP sensor disconnected, defective • Feed-out belt motor drive overloaded due to obstruction (jammed paper, paper scraps, etc.) |
| Error code: | 722-42 |
| Description: | 1000-Sheet Finisher Error. Stapler movement motor • The stapler HP sensor does not detect the home position of the stapler within the prescribed time after the stapler has moved to its home position. • The stapler HP sensor does not turn off within the prescribed time after the stapler has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure causes this SC code. |
| Causes: | • Stapler movement motor harness loose or broken • Stapler HP sensor harness loose, broken • Stapler movement motor disconnected, defective • Stapler HP sensor disconnected, defective • Stapler or motor drive overloaded due to obstruction (jammed paper, paper scraps, etc.) |
| Error code: | 722-44 |
| Description: | 1000-Sheet Finisher Error. Corner stapler motor error • The corner stapler motor does not switch off within the prescribed time after operating. • The corner stapler HP sensor does not detect the home position of the corner stapler within the prescribed time after the corner stapler has moved to its home position. • The corner stapler HP sensor does not turn off within the prescribed time after the corner stapler has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure causes this SC code. |
| Causes: | • Staple jam • Corner stapler motor disconnected, defective • Corner stapler motor harness is loose or broken • Corner stapler HP sensor disconnected, defective • Number of sheets in stack exceeds allowed number of sheets for stapling • Stapler motor obstructed |
| Error code: | 722-70 |
| Description: | 1000-Sheet Finisher Error. Tray lift motor error The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. The 1st detection failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | • Tray lift motor disconnected, defective • Tray lift motor harness is loose or broken • Stack height sensor disconnected, defective • Tray lift motor overloaded due to obstruction (jammed paper, paper scraps, etc.) |
| Error code: | 722-71 |
| Description: | 1000-Sheet Finisher Error. Shift tray motor error • The shift roller HP sensor does not detect the home position of the upper tray within the specified number of pulses after the upper tray has moved to its home position. • The shift roller HP sensor does not turn off within the specified number of pulses after the upper tray has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray motor disconnected, defective • Shift tray motor harness is loose or broken • Shift tray HP sensor disconnected, defective • Shift tray motor overloaded due to obstruction (jammed paper, paper scraps, etc.) |
| Error code: | 770 |
| Description: | Shift motor error The shift motor HP sensor does not detect any change for 1.86 seconds after the shift motor has turned on at power on or during its operation. |
| Causes: | Defective shift motor. Defective shift motor HP sensors. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 791 |
| Description: | Bridge unit error The machine recognizes the finisher, but does not recognize the bridge unit. |
| Causes: | The bridge unit is not installed. Defective bridge unit. Re-install the bridge unit. Turn the main power switch off and on. |
| Remedy: | • Re-install the bridge unit. • Turn the main power switch off and on. |
| Error code: | 792 |
| Description: | Finisher error The machine does not recognize the finisher, but recognizes the bridge unit. |
| Causes: | The finisher`s connection is faulty. The finisher is not attached to a device equipped with the bridge unit. Defective finisher. |
| Remedy: | Reconnect the finisher or bridge unit, and then turn the main power switch off and then back on. |
| Error code: | 816 |
| Display: | SYSTEM HALT (*) 816 : FW/FROM WRC |
| Description: | Energy saving I/O sub-system error |
| Causes: | The energy saving I/O sub-system detects an error. • Defective energy saving I/O sub-system • The energy saving I/O sub-system detects a controller board error (No response) |
| Remedy: | • Turn the main power switch off and on. • Replace the controller board. |
| Error code: | 817 |
| Display: | SYSTEM HALT (*) 817 : FW/SaveArea |
| Description: | Monitor error This is a file detection and electronic file signature check error when the boot loader attempts to read the self-diagnostic module, system kernel, or root system files from the OS Flash ROM, or the items on the SD card in the controller slot are false or corrupted. |
| Causes: | OS Flash ROM data defective. SD card data defective. Change the controller firmware. Use another SD card. |
| Remedy: | • Change the controller firmware. • Use another SD card. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 833 |
| Display: | SYSTEM HALT (*) 833 : FW/PRN MDL |
| Description: | Self-diagnostic error 8: Engine I/F ASIC |
| Causes: | [0F30] [0F31] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. [0F41] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. |
| Error code: | 835 |
| Display: | SYSTEM HALT (*) 835 : FW/PRN MDL |
| Description: | Self-diagnostic error: Centronic device |
| Causes: | [1102] Loopback connector is connected but check results in an error. • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [110C] Loopback connector is connected but check results in an error. • ASIC device error • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [1120] Centronic loopback connector is not connected for detailed self-diagnostic test. • Centronic loopback connector not connected correctly • Centronic loopback connector defective • ASIC device defective Replace the controller board. |
| Error code: | 838 |
| Display: | SYSTEM HALT (*) 838 : FW/SV MDL |
| Description: | Self-diagnostic Error 10: Clock Generator A verify error occurred when setting data was read from the clock generator via the I2C bus. |
| Causes: | • Replace the controller board |
| Error code: | 839 |
| Display: | SYSTEM HALT (*) 839 : FW/PRN MDL |
| Description: | Serial Flash A read/write operation on the Software Status Register failed. |
| Causes: | • Replace the controller board |
| Error code: | 840 |
| Description: | EEPROM access error During the I/O processing, reading error is occurred. The 3rd reading failure issues this SC code. During the I/O processing, writing error is occurred. |
| Causes: | Defective EEPROM |
| Error code: | 841 |
| Description: | EEPROM read error Mirrored data of the EEPROM is different from the original data in EEPROM. |
| Causes: | Data in the EEPROM is overwritten for some reason. |
| Error code: | 842 |
| Description: | Service Scanner |
| Causes: | This error indicates that a scanner communications failure. |
| Remedy: | 1 Scanner control card to flatbed inteconnect card cable Check for correct installation of the scan control to flatbed interconnect card cable. 2 Motor drive card to flatbed interconnect card cable Check for correct installation of the motor driver card to flatbed interconnect card cable. 3 Motor driver card Flatbed interconnect card If the cables are good and are properly connected, replace the following FRUs in the order shown: • Flatbed interconnect card assembly • Motor driver card assembly |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 858 |
| Description: | Data encryption conversion error (1) |
| Causes: | -01 A serious error has occurred during the data conversion performed for updating the key for data encryption. • The data in the USB flash drive is damaged. • A communication error has occurred due to electromagnetic waves or other noise. • Replace the controller board. * However, if it is "-30", the machine may recover by turning the main power switch off and then back on. -02 A Data encryption conversion error (2) A serious error occurs when data is encrypted to update an encryption key. Defective NVRAM Replace the controller board. -30 A Data encryption conversion error (3) A recoverable error has occurred before starting data conversion. Defective NVRAM • Turn the main switch off and on. • If the error reoccurs, replace the controller board. -31 A A serious error occurs while the data is encrypted. Same as SC991 Same as SC991 |
| Error code: | 859 |
| Description: | HDD data encryption error |
| Causes: | -01 B HDD check error • Hard disk data conversion has been selected, but the hard disk is not installed. • The hard disk is not mounted properly. • No HDD installed • Hard disk formatting is not completed. • The encryption key on the board and the actual encryption key in the hard disk do not match. • Install the HDD correctly. • Initialize the HDD with SP5-832-001. -02 B Power failure during data encryption. The data conversion in the NVRAM or hard disk has not completed successfully. Power interruption has occurred during the conversion of the data in the NVRAM or hard disk Initialize the HDD with SP5-832-001. -10 B Data Read/Write command error Due to time-out, serial communication error, or other problems in DMAC, an irregular DMAC return value has occurred consecutively two or more times Noise or other problems in the SATA connection Same as SC863 |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 862 |
| Description: | Bad sector number error The number of bad sectors in the HDD (image data area) goes over 101. |
| Causes: | • Defective HDD |
| Remedy: | Format the HDD with SP5832-001. Replace the HDD. |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 877 |
| Description: | HDD Data Erase Error The Data Overwrite Security option cannot scramble and erase data on the HDD because the DOS SD card has been corrupted or has |
| Causes: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not been removed from the SD card slot. |
| Remedy: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not solve the problem, the SD card has been damaged.) • Install a new NVRAM • Install a new Data Overwrite Security option with a new SD card |
| Error code: | 878 |
| Description: | TPM electronic recognition error |
| Causes: | -00 The system firmware is not authenticated by TPM. The system hash value registered in the TPM at the machine`s system startup does not match that registered in the USB flash drive. • The system module was updated without going through the formal update process. • Incorrect operating of the USB flash. Replace the board. -01 D USB Flash error An error has occurred in the file system in the USB flash drive. The file system of the USB flash drive is damaged. Replace the controller board. -02 D TPM error An error has occurred in the TPM or TPM driver. Defective TPM Replace the controller board. -03 D TCSD error An error has occurred in the TPM software stack. • The TPM software stack cannot be launched. • The file required for the TPM software stack is missing. Replace the controller board. |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 881 |
| Description: | Management area error Defective software has been detected. |
| Causes: | Abnormal accumulation of authentication information in the software |
| Remedy: | Turn the main switch off and on. |
| Error code: | 899 |
| Display: | Power OFF/ON Error : 899 |
| Description: | Software error A software error occurred in the GW controller. |
| Causes: | • Cycle the machine off/on • Update controller firmware • Controller board defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 994 |
| Display: | Service Call 994:Error |
| Description: | Density Sensor Error |
| Causes: | • No action required because this SC does not interfere with operation of the machine. |
| Remedy: | 1 Is the front door fully closed? Go to step 2. Close the front door. 2 Is the density sensor actuator stuck in place? Release the density sensor actuator. Go to step 3. 3 Are connectors CN406 and CN407 on the sensor board connected properly? Go to step 4. Plug the connector in securely. 4 Is connector CN15 on the printer controller board connected properly? Replace the density sensor. Go to step 5. Plug the connector in securely. 5 Did replacing the density sensor fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 995 |
| Description: | Finisher Main Feed Motor abnormal |
| Causes: | -01 D • Defective BCU • NVRAM Replacement error • Install the previous NVRAM • Input the serial number with SP5-811-004, and turn the main power switch off and on. -02 D • Defective NVRAM • Defective controller Perform SP5-825 to download the appropriate data to the NVRAM, and then turn the main power switch off and then back on. -03 D The serial number cannot be identified due to a mistake during controller replacement or mechanical failure. Replace the controller with the correct type. -04 D - Place all parts in the initial state, and then replace the parts according to the procedures described in the manuals. |
| Remedy: | 1 Is there jammed paper or other obstructions in the paper path? Clear the paper path. Go to step 2. 2 Check to ensure the connector PJ6 on the finisher control board and the feed motor assembly cable are properly connected. Are the cables properly connected? Go to step 3. Properly connect the cables. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pins 7 and 8 and +5 V dc (–10%) between pins 7 and 6 on the feed motor assembly cable connector CN1. Is either voltage missing? Go to step 4. Go to step 5. 4 Disconnect the feed motor assembly cable and PJ6 on the finisher control board. Measure continuity on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 5 Replace the feed motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 6 Measure for +24 V dc between pins 1 and 2 on connector PJ3 on the finisher control board. Measure for +5 V dc between pins 1 and 3 on PJ2 on the finisher control board. Is either voltage missing? Replace the power supply. Replace the finisher control board. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
Название
RICOH TYPE K Скрепки с картриджем
RICOH TYPE K Скрепки (3 упаковки)
RICOH TYPE L Скрепки буклетные в картридже
RICOH TYPE L Скрепки буклетные (в упаковке 4*2000шт.)
RICOH TYPE MP4500E Тонер-туба
RICOH Девелопер черный
RICOH Фотобарабан /OPC Drum/
