Ricoh MP7000SP
Рейтинг
Модули
DEVELOPMENT UNIT 2
TONER SUPPLY UNIT
ELECTRICAL SECTION 2
DF DRIVE/ELECTRICAL 2
DF ORIGINAL EXIT
DF ORIGINAL TRANSFER 1
PAPER EXIT SECTION 3
EXTERIOR 2
PAPER EXIT SECTION 2
PAPER FEED UNIT 2
ELECTRICAL SECTION 3
ELECTRICAL SECTION 7
PCU 4
PCU 2
PAPER REGISTRATION 3
DF ORIGINAL FEED 1
DF EXTERIOR
DUPLEX UNIT 4
Drive Section 1
ELECTRICAL SECTION 9
UNIVERSAL TRAY
TANDEM TRAY 2
DF ORIGINAL TRANSFER 4
TRANSFER BELT UNIT 1
OPTICS SECTION 4
Frame Section 4
ELECTRICAL SECTION 6
PAPER EXIT SECTION 1
OPTICS SECTION 2
Fusing Unit 4
PCU 3
DF ORIGINAL FEED 2
ELECTRICAL SECTION 4
ELECTRICAL SECTION 1
DF FRAME SECTION
TANDEM TRAY 3
ELECTRICAL SECTION 5
EXTERIOR 1
DF ORIGINAL TRANSFER 3
DUPLEX UNIT 2
OPTICS SECTION 1
TANDEM TRAY 1
ELECTRICAL SECTION 8
OPERATION PANEL
DEVELOPMENT UNIT 1
VERTICAL TRANSPORT
OPTICS SECTION 3
DF ORIGINAL TRANSFER 2
PAPER REGISTRATION 2
DF DRIVE/ELECTRICAL 1
DUPLEX UNIT 3
PCU 1
FUSING UNIT 2
LASER UNIT
Paper feed unit 1
FUSING UNIT 1
TONER HOPPER SECTION
DUPLEX UNIT 5
PAPER REGISTRATION 1
TONER COLLECTION
TRANSFER BELT UNIT 2
FRAME SECTION 2
FRAME SECTION 1
FUSING UNIT 3
DUPLEX UNIT 1
BY-PASS FEED TRAY
Frame Section 3
DRIVE SECTION 2
Детали DF ORIGINAL TRANSFER 4
| Деталь: | Development Roller |
| Парткод: | B065 3062 |
| Деталь: | Ball Bearing - 12x21x5 |
| Парткод: | B065 3080 |
| Деталь: | Bushing - 8mm |
| Парткод: | B065 3069 |
| Деталь: | Development Roller Adjuster |
| Парткод: | B065 3077 |
| Деталь: | Stopped Screw - M4x17 |
| Парткод: | AA14 3426 |
| Деталь: | Bushing:4mm |
| Парткод: | B070 3115 |
| Деталь: | Classification Assy |
| Парткод: | B247 3161 |
| Деталь: | Toner Separation Joint Seal |
| Парткод: | B065 3122 |
| Деталь: | Rear Toner Separation Joint Seal |
| Парткод: | B065 3123 |
| Деталь: | Toner Separation Drive Shaft |
| Парткод: | B065 3125 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Boss:Bearing:Agitator:Press Fit |
| Парткод: | B247 3176 |
| Деталь: | Transport Screw |
| Парткод: | B247 3720 |
| Деталь: | Case Seal |
| Парткод: | A229 3154 |
| Деталь: | Idle Gear |
| Парткод: | B065 3138 |
| Деталь: | Toner Collection Gear |
| Парткод: | B065 3139 |
| Деталь: | Toner End Sensor:Assy |
| Парткод: | B247 5311 |
| Деталь: | Slitter |
| Парткод: | A096 3181 |
| Деталь: | Slitter Cover Seal |
| Парткод: | AA15 0361 |
| Деталь: | NUT |
| Парткод: | B065 3146 |
| Деталь: | Lower Front Case Seal - Rear |
| Парткод: | B065 3152 |
| Деталь: | Lower Filter Case Filter |
| Парткод: | B065 3153 |
| Деталь: | Lower Right Case Seal |
| Парткод: | B065 3151 |
| Деталь: | Toner Supply Unit:Assy |
| Парткод: | B247 3200 |
| Деталь: | UPPER COVER |
| Парткод: | B065 3140 |
| Деталь: | Exit Toner Pile |
| Парткод: | B065 3141 |
| Деталь: | Toner Separation Spring |
| Парткод: | B065 3143 |
| Деталь: | Toner Separation Shutter |
| Парткод: | B065 3142 |
| Деталь: | Bushing 8x14x8 |
| Парткод: | B247 3175 |
| Деталь: | SPRING |
| Парткод: | AA06 0291 |
| Деталь: | Joint Gear - 15Z |
| Парткод: | AB01 3748 |
| Деталь: | Gear - 16Z |
| Парткод: | AB01 3747 |
| Деталь: | Gear - 15Z |
| Парткод: | AB01 3749 |
| Деталь: | HDD Stay |
| Парткод: | B247 5835 |
| Деталь: | HDD bracket |
| Парткод: | B247 5834 |
| Деталь: | Rubber Cushion |
| Парткод: | AA16 1125 |
| Деталь: | Screw:M3x4.2 |
| Парткод: | AA14 3548 |
| Деталь: | Harness - HDD Power Source |
| Парткод: | B247 5551 |
| Деталь: | Harness:HDD:IDE:Assy |
| Парткод: | B247 5552 |
| Деталь: | HDD:Hitachi:80GB:Path2:Pata |
| Парткод: | B247 5227 |
| Деталь: | Harness - AC Power Supply CTL-PSU |
| Парткод: | B247 5622 |
| Деталь: | Harness:AC Power Supply:CTL-PSU:EU |
| Парткод: | B246 5623 |
| Деталь: | Harness - Pwrctl |
| Парткод: | B247 5460 |
| Деталь: | INTERFACE HARNESS |
| Парткод: | B477 5751 |
| Деталь: | Harness:Registration Sensor:Unit |
| Парткод: | B477 5602 |
| Деталь: | Harness:Cis:LVDS |
| Парткод: | B477 5765 |
| Деталь: | Detection Sensor Harness |
| Парткод: | B477 5611 |
| Деталь: | Harness:Sensor:Original Sensor |
| Парткод: | B477 5625 |
| Деталь: | Harness:ADF-CIS:Control - DC |
| Парткод: | B477 5736 |
| Деталь: | Pick-up Motor Harness |
| Парткод: | B477 5711 |
| Деталь: | PCB:ADF:Assy |
| Парткод: | B477 5585 |
| Деталь: | Paper Feed Motor Harness |
| Парткод: | B477 5691 |
| Деталь: | CIS Harness |
| Парткод: | B477 5721 |
| Деталь: | Exit Motor - DC 3.9W |
| Парткод: | B477 3731 |
| Деталь: | Screw:Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Scanning Motor- DC 7.4W |
| Парткод: | B477 3721 |
| Деталь: | Scanning Motor Stay |
| Парткод: | B477 3215 |
| Деталь: | Scanning Motor Bracket |
| Парткод: | B477 3211 |
| Деталь: | Tension Spring:Tension:Transport |
| Парткод: | AA06 0991 |
| Деталь: | PULLEY |
| Парткод: | B477 3217 |
| Деталь: | Timing Belt:60S2M296 |
| Парткод: | AA04 3330 |
| Деталь: | Timing Belt:60S3M114 |
| Парткод: | AA04 3331 |
| Деталь: | Rubber Bushing - Vibration Damper |
| Парткод: | 59 362 321 |
| Деталь: | Timing Belt:80S2M166 |
| Парткод: | AA04 3329 |
| Деталь: | Timing Belt:80S3M516 |
| Парткод: | AA04 3332 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A806 2285 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A806 2287 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A806 2283 |
| Деталь: | Timing Pulley - T30/Z20 S2M/M0.8 |
| Парткод: | A806 2161 |
| Деталь: | Spacer - 8x20x1 |
| Парткод: | AA132152 |
| Деталь: | Timing Belt:B40S2M158 |
| Парткод: | B652 2347 |
| Деталь: | Bracket:Motor:Base |
| Парткод: | B477 2334 |
| Деталь: | Stepper Motor:Base:Rise:Assy |
| Парткод: | B652 2911 |
| Деталь: | Spring - 12.6n |
| Парткод: | B477 4141 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | PULLEY |
| Парткод: | B477 3175 |
| Деталь: | Screw:Safety |
| Парткод: | AA14 3791 |
| Деталь: | Tension:Peen |
| Парткод: | B477 3236 |
| Деталь: | Motor Bracket Cushion |
| Парткод: | B477 2333 |
| Деталь: | Spacer:PCB |
| Парткод: | B477 5521 |
| Деталь: | Gear - 21Z |
| Парткод: | B477 3241 |
| Деталь: | Back Scanning Positioning Pin |
| Парткод: | B477 2661 |
| Деталь: | Long Arm Shaft |
| Парткод: | B477 2641 |
| Деталь: | Lower Exit Guide Plate |
| Парткод: | B477 2631 |
| Деталь: | Short Arm Shaft |
| Парткод: | B477 2645 |
| Деталь: | Driven Exit Scanning Roller |
| Парткод: | B477 2636 |
| Деталь: | Exit Arm Spring |
| Парткод: | B477 4127 |
| Деталь: | Driven Exit Arm |
| Парткод: | B477 2637 |
| Деталь: | BUSHING - 6MM |
| Парткод: | B477 2653 |
| Деталь: | Spring - 12n |
| Парткод: | B477 4129 |
| Деталь: | Back Scanning Roller |
| Парткод: | B477 2651 |
| Деталь: | Discharge Brush:L11 |
| Парткод: | B477 2622 |
| Деталь: | Pressure Plate Tape |
| Парткод: | B477 2715 |
| Деталь: | Lower Exit |
| Парткод: | B477 2611 |
| Деталь: | Guide Plate Bracket |
| Парткод: | B477 2881 |
| Деталь: | DISCHARGE BRUSH:GUIDE PLATE |
| Парткод: | B477 2882 |
| Деталь: | Bushing- Exit Driven Roller |
| Парткод: | A859 4836 |
| Деталь: | SPRING |
| Парткод: | B477 4131 |
| Деталь: | DRIVEN EXIT ROLLER |
| Парткод: | B477 2861 |
| Деталь: | Exit Arm |
| Парткод: | B477 2872 |
| Деталь: | SPRING |
| Парткод: | B477 4132 |
| Деталь: | Lower Exit Guide Plate Sheet |
| Парткод: | B477 2851 |
| Деталь: | Lower Exit Guide |
| Парткод: | B477 2841 |
| Деталь: | Exit Shaft |
| Парткод: | B477 2875 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Front Cover Bracket |
| Парткод: | B477 1841 |
| Деталь: | Sound Proofing Material:Cover:Paper Feed |
| Парткод: | B477 4915 |
| Деталь: | Rear Cover Bracket |
| Парткод: | B477 1851 |
| Деталь: | Paper Feed Release Lever |
| Парткод: | B4771825 |
| Деталь: | SPRING |
| Парткод: | B477 4117 |
| Деталь: | Grip Shaft |
| Парткод: | B4771831 |
| Деталь: | Paper feed Cover |
| Парткод: | B477 1791 |
| Деталь: | Decal - Misfeed Removal |
| Парткод: | B477 4352 |
| Деталь: | Paper Feed Cover Grip |
| Парткод: | B477 1821 |
| Деталь: | Decal:Size:Original |
| Парткод: | B6521807 |
| Деталь: | Pull Out Roller Bracket |
| Парткод: | B477 2361 |
| Деталь: | Anistatic Brush |
| Парткод: | A697 2131 |
| Деталь: | Paper Feed Grounding Plate |
| Парткод: | B477 2391 |
| Деталь: | Paper Size Relay Harness |
| Парткод: | B477 5651 |
| Деталь: | Photointerruptor:Paper Size Sensor |
| Парткод: | AW02 0155 |
| Деталь: | PHOTOINTERRUPTOR:ENTRANCE |
| Парткод: | AW02 0154 |
| Деталь: | Paper Size Sensor Bracket |
| Парткод: | B477 2382 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0037 |
| Деталь: | SPRING |
| Парткод: | B477 4111 |
| Деталь: | Driven Pull Out Roller |
| Парткод: | B477 2351 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Relay Roller Arm |
| Парткод: | B477 2373 |
| Деталь: | Driven Paper Feed Roller |
| Парткод: | B477 2372 |
| Деталь: | SPRING |
| Парткод: | B477 4113 |
| Деталь: | Guide:Paper Feed:Upper |
| Парткод: | B477 2342 |
| Деталь: | Registration Relay Harness |
| Парткод: | B477 5671 |
| Деталь: | Timing Belt:S2m:40x426 |
| Парткод: | AA04 3315 |
| Деталь: | Left Exit Tray |
| Парткод: | B065 4252 |
| Деталь: | Exit Roller:Drive:Exit |
| Парткод: | B247 4460 |
| Деталь: | Eft Reverse Guide Plate Assy |
| Парткод: | B140 4308 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AA04 0056 |
| Деталь: | PRESSURE ARM |
| Парткод: | A229 4467 |
| Деталь: | Exit Arm Pad |
| Парткод: | B065 4424 |
| Деталь: | Guide Plate Lever |
| Парткод: | B065 4422 |
| Деталь: | Shaft:Pressure:Guide Plate:Assy |
| Парткод: | B247 4421 |
| Деталь: | Spring - Lower Exit Roller |
| Парткод: | B247 4456 |
| Деталь: | Rear Harness Bracket |
| Парткод: | B065 4459 |
| Деталь: | Shift Clutch |
| Парткод: | A4701703 |
| Деталь: | Timing Pulley - 27Z |
| Парткод: | AB03 0579 |
| Деталь: | GEAR |
| Парткод: | AB01 2031 |
| Деталь: | Bracket:Swivel:Assy |
| Парткод: | B247 4400 |
| Деталь: | Exit Gear |
| Парткод: | AB01 9197 |
| Деталь: | Harness - Paper Exit Unit Drawer |
| Парткод: | B140 4497 |
| Деталь: | Exit Drawer Bracket |
| Парткод: | B140 4458 |
| Деталь: | Tightener:Exit:Assy |
| Парткод: | B247 4315 |
| Деталь: | LOCK SPRING |
| Парткод: | B247 4403 |
| Деталь: | TENSION SPRING |
| Парткод: | B247 4454 |
| Деталь: | Idle Pulley - 11mm |
| Парткод: | B065 4317 |
| Деталь: | GEAR |
| Парткод: | AB01 9200 |
| Деталь: | Washer:DIA6.3xDIA18x1 |
| Парткод: | B247 4487 |
| Деталь: | Toner Collection Bottle Bracket |
| Парткод: | B065 3689 |
| Деталь: | Ratch |
| Парткод: | A096 3712 |
| Деталь: | Tank:Discharge Used Toner |
| Парткод: | B065 3690 |
| Деталь: | Caution Decal - English |
| Парткод: | AA00 0059 |
| Деталь: | Large Cap - Toner Collection Tank |
| Парткод: | A007 3751 |
| Деталь: | Lower left cover |
| Парткод: | B065 1334 |
| Деталь: | Decal - Cover |
| Парткод: | B065 4480 |
| Деталь: | G4 Cap |
| Парткод: | B065 1344 |
| Деталь: | LEFT UPPER COVER |
| Парткод: | B140 1304 |
| Деталь: | UPPER LEFT COVER |
| Парткод: | B065 1244 |
| Деталь: | Decal - Exposure Glass Cleaning |
| Парткод: | B477 4391 |
| Деталь: | Screw:M4:Dia5 |
| Парткод: | AA14 3559 |
| Деталь: | Inner Cover - Operation Panel |
| Парткод: | B247 1312 |
| Деталь: | Fan Motor DC24V/1.44W |
| Парткод: | AX64 0175 |
| Деталь: | Fan bracket |
| Парткод: | B065 1345 |
| Деталь: | UPPER REAR COVER |
| Парткод: | B065 1309 |
| Деталь: | Capaciter Louver |
| Парткод: | B247 1306 |
| Деталь: | Machine Or Copier Filter |
| Парткод: | AA01 2128 |
| Деталь: | Louver Filter |
| Парткод: | B247 1332 |
| Деталь: | Seal - Duct Cover |
| Парткод: | B247 1354 |
| Деталь: | Cover:Rear Upper:NA |
| Парткод: | B246 1305 |
| Деталь: | Cover - Rear Upper |
| Парткод: | B247 1305 |
| Деталь: | Ozone Filter:Rear |
| Парткод: | B246 1234 |
| Деталь: | Ozone Filter:Front |
| Парткод: | B246 1233 |
| Деталь: | Duct Holder |
| Парткод: | A2931332 |
| Деталь: | Exhaust duct cover |
| Парткод: | B247 1237 |
| Деталь: | Cover - Rear Lower |
| Парткод: | B247 1308 |
| Деталь: | Screw:M4:Exterior |
| Парткод: | AA14 3801 |
| Деталь: | UPPER RIGHT COVER |
| Парткод: | B065 1302 |
| Деталь: | NCU Cap |
| Парткод: | B065 1343 |
| Деталь: | LCT Cover |
| Парткод: | B065 1303 |
| Деталь: | UPPER RIGHT COVER |
| Парткод: | B065 1310 |
| Деталь: | Lower right cover |
| Парткод: | B065 1333 |
| Деталь: | Connector cap |
| Парткод: | B065 1341 |
| Деталь: | Coupling Cap |
| Парткод: | B065 1342 |
| Деталь: | Tank Seal |
| Парткод: | AA15 2315 |
| Деталь: | SPRING |
| Парткод: | AA06 0902 |
| Деталь: | DC Solenoid 24V |
| Парткод: | B247 4415 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2117 |
| Деталь: | Exit Drum Stay |
| Парткод: | B065 4441 |
| Деталь: | Reverse Roller:Drive |
| Парткод: | B247 4463 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 2028 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AA04 0056 |
| Деталь: | Exit Roller Holder |
| Парткод: | A229 4482 |
| Деталь: | Reverse Guide Plate - Right |
| Парткод: | A229 4479 |
| Деталь: | Reverse Guide Plate |
| Парткод: | A229 4477 |
| Деталь: | Exit Gate Pawl |
| Парткод: | B065 4413 |
| Деталь: | Roller:Decura:Exit |
| Парткод: | B247 4439 |
| Деталь: | Roller:Decura:Entrance |
| Парткод: | B247 4438 |
| Деталь: | Screw:A |
| Парткод: | AA14 3807 |
| Деталь: | Lower Entrance Guide Plate |
| Парткод: | B065 4254 |
| Деталь: | Nylon Rivet |
| Парткод: | A048 2838 |
| Деталь: | Timing Pulley - 18Z |
| Парткод: | AB03 0578 |
| Деталь: | Gear - 21/35Z |
| Парткод: | B140 4306 |
| Деталь: | Gear - 21/35Z |
| Парткод: | B140 4304 |
| Деталь: | Gear:Swivel:Assy |
| Парткод: | B247 4317 |
| Деталь: | Gear - 21/33Z |
| Парткод: | B140 4322 |
| Деталь: | Drive Bracket Assy |
| Парткод: | B140 4325 |
| Деталь: | Front Drive Bracket Assy |
| Парткод: | B140 4329 |
| Деталь: | Gear - IDLER WORM GEAR |
| Парткод: | B140 4336 |
| Деталь: | Stepper Motor DC3.4V |
| Парткод: | B247 4324 |
| Деталь: | Heat Insulating Plate Bracket |
| Парткод: | B140 4474 |
| Деталь: | Pressure Tension Spring |
| Парткод: | B140 4300 |
| Деталь: | Guide Plate:Swivel:Adhesion |
| Парткод: | B181 6640 |
| Деталь: | Transport Roller |
| Парткод: | AF022149 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0327 |
| Деталь: | Driven Shaft |
| Парткод: | AA14 0829 |
| Деталь: | Transport Roller Lever |
| Парткод: | B065 6453 |
| Деталь: | Screw - Scale |
| Парткод: | AA14 3812 |
| Деталь: | Driven Release Lever |
| Парткод: | B065 6454 |
| Деталь: | Driven Pressure Lever |
| Парткод: | B065 6455 |
| Деталь: | Relay Shaft |
| Парткод: | B065 6317 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1469 |
| Деталь: | Rear Side Plate - Paper Feed |
| Парткод: | B065 6330 |
| Деталь: | Gear - 18Z |
| Парткод: | AB01 1470 |
| Деталь: | Tray Link Guide |
| Парткод: | B065 6452 |
| Деталь: | Paper Tray Link |
| Парткод: | B065 6346 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3718 |
| Деталь: | SPRING |
| Парткод: | AA06 0901 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3575 |
| Деталь: | Pulley:Idler:30t/24z |
| Парткод: | AB01 7690 |
| Деталь: | Vertical Transport Link |
| Парткод: | B065 6456 |
| Деталь: | SPRING |
| Парткод: | AA06 0900 |
| Деталь: | Pulley - 30Z |
| Парткод: | AB03 0734 |
| Деталь: | Gear - 38Z |
| Парткод: | AB01 1490 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 1491 |
| Деталь: | Reverse Drive Shaft |
| Парткод: | B065 6306 |
| Деталь: | Reverse Gear |
| Парткод: | AB01 1471 |
| Деталь: | Gear:Reverse |
| Парткод: | AB01 1591 |
| Деталь: | DC Solenoid:Reverse:Assy |
| Парткод: | B132 6670 |
| Деталь: | Motor Base |
| Парткод: | B065 6415 |
| Деталь: | Front Side Plate - Paper Feed |
| Парткод: | B065 6336 |
| Деталь: | Support Guide Plate |
| Парткод: | B065 6371 |
| Деталь: | Reverse Haousing |
| Парткод: | B065 6333 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3576 |
| Деталь: | Reverse Driven Shaft |
| Парткод: | B065 6307 |
| Деталь: | Torque Limiter - 53mnxm |
| Парткод: | A294 6700 |
| Деталь: | Paper Feed Roller:Separate |
| Парткод: | AF03 2080 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Stepper Motor:Paper Feed Unit:Assy |
| Парткод: | B132 6655 |
| Деталь: | MOTOR BRACKET |
| Парткод: | B065 6394 |
| Деталь: | SPRING |
| Парткод: | AA06 0904 |
| Деталь: | Pulley - 20T |
| Парткод: | AB03 0733 |
| Деталь: | Ground Plate:Stepper Motor:Paper Feed Unit |
| Парткод: | B140 6378 |
| Деталь: | Cover - SD-Card |
| Парткод: | B247 5879 |
| Деталь: | Interface Panel |
| Парткод: | B101 5993 |
| Деталь: | Cover:Connector:Control Board |
| Парткод: | B132 5925 |
| Деталь: | Large Drum Stay Ground Plate |
| Парткод: | B070 6877 |
| Деталь: | Ground Plate 5 |
| Парткод: | B140 5836 |
| Деталь: | PCB:NIC+USB |
| Парткод: | B736 5660 |
| Деталь: | Cover 2ch |
| Парткод: | B247 5883 |
| Деталь: | SD-Card Copy |
| Парткод: | B247 5105 |
| Деталь: | PCB Control Board |
| Парткод: | B247 5112 |
| Деталь: | NVRAM |
| Парткод: | B246 9590 |
| Деталь: | Rail:Fax Control Unit |
| Парткод: | B622 5874 |
| Деталь: | Cover - Fax |
| Парткод: | B247 5881 |
| Деталь: | Cover - 1ch |
| Парткод: | B247 5882 |
| Деталь: | Cover - CSS |
| Парткод: | B247 5869 |
| Деталь: | PCB:SDRAM-DIMM:256MB:PBF:Assy |
| Парткод: | G332 5721 |
| Деталь: | Harness - Bank Front 3way |
| Парткод: | B247 5701 |
| Деталь: | Harness - Bank Safety Switch |
| Парткод: | B247 5483 |
| Деталь: | PCB pFC 3way |
| Парткод: | B247 5132 |
| Деталь: | pFC Board Bracket |
| Парткод: | B065 5871 |
| Деталь: | Upper pFC Board Stay |
| Парткод: | B065 5873 |
| Деталь: | Lower pFC Board Stay |
| Парткод: | B065 5872 |
| Деталь: | POWER SUPPLY UNIT |
| Парткод: | AZ24 0111 |
| Деталь: | Power Supply Unit - 230V |
| Парткод: | AZ240121 |
| Деталь: | Harness - DC Power Supply pFC |
| Парткод: | B247 5502 |
| Деталь: | Bottle Guide |
| Парткод: | B065 3695 |
| Деталь: | Harness - Bank Dehumidifier |
| Парткод: | B247 5601 |
| Деталь: | Power Supply Cord - 120V |
| Парткод: | B065 5672 |
| Деталь: | Power Supply Cord:EU |
| Парткод: | B246 5677 |
| Деталь: | Right PSU Stay |
| Парткод: | B065 5879 |
| Деталь: | Lower Arm |
| Парткод: | B247 5826 |
| Деталь: | Harness - Pwrctl |
| Парткод: | B247 5461 |
| Деталь: | Cover Temperature & Humidity Sensor |
| Парткод: | B1103777 |
| Деталь: | THERMISTOR |
| Парткод: | AW10 0107 |
| Деталь: | GROUNDING PLATE |
| Парткод: | B065 1843 |
| Деталь: | Bracket:Ground Plate:Power Supply Unit |
| Парткод: | B247 5828 |
| Деталь: | Guide Plate:Cover:Rear Upper |
| Парткод: | B247 5822 |
| Деталь: | PCB:pFC |
| Парткод: | B247 5077 |
| Деталь: | Holder:Power Supply Unit:NA |
| Парткод: | B246 5898 |
| Деталь: | Holder:Power Supply Unit:M-C3 |
| Парткод: | B249 5879 |
| Деталь: | Ground Plate - Lens Stay |
| Парткод: | A2941838 |
| Деталь: | Pickoff Pawl:Drum:Assy |
| Парткод: | B065 2336 |
| Деталь: | Bracket Grounding Bracket |
| Парткод: | B065 2358 |
| Деталь: | Pick-off Pawl Spring |
| Парткод: | AA06 0892 |
| Деталь: | Pick-off Pawl |
| Парткод: | AD02 5024 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3523 |
| Деталь: | Screw - M3 |
| Парткод: | AA14 3544 |
| Деталь: | Pick-off Pawl Cam |
| Парткод: | AB01 7611 |
| Деталь: | SPRING |
| Парткод: | AA06 3576 |
| Деталь: | Spacer - M6 |
| Парткод: | AA13 2208 |
| Деталь: | Spring - 4060mN |
| Парткод: | AA06 3610 |
| Деталь: | Front Blade Seal |
| Парткод: | B065 2316 |
| Деталь: | Bracket:Blade:Assy |
| Парткод: | B247 2314 |
| Деталь: | Rear Blade Seal |
| Парткод: | B065 2317 |
| Деталь: | BUSHING |
| Парткод: | AA08 2120 |
| Деталь: | Middle PCU Casing |
| Парткод: | B065 2386 |
| Деталь: | Bracket:Brush Roller |
| Парткод: | B065 2389 |
| Деталь: | Shaft:Pickoff Pawl:Swivel |
| Парткод: | B247 2342 |
| Деталь: | Toner Collection Coil Gear |
| Парткод: | AB01 1459 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Harness:PCU:Lower |
| Парткод: | B247 2497 |
| Деталь: | Density Sensor P |
| Парткод: | B234 2279 |
| Деталь: | Pick-off Pawl Positioning Plate |
| Парткод: | B065 2364 |
| Деталь: | Entrance Seal Holder |
| Парткод: | B065 2361 |
| Деталь: | Cleaning Entrance Seal |
| Парткод: | B065 2362 |
| Деталь: | GROUNDING PLATE |
| Парткод: | B065 2381 |
| Деталь: | Bracket:Idler:Pickoff Pawl:Assy |
| Парткод: | B247 2344 |
| Деталь: | Idler Gear |
| Парткод: | AB01 1460 |
| Деталь: | Toner Collection Coil Bushing |
| Парткод: | AA08 2121 |
| Деталь: | Grounding Plate - Entrance Seal |
| Парткод: | B065 2369 |
| Деталь: | Upper Unit Cover |
| Парткод: | A293 2418 |
| Деталь: | Shield Glass Cover |
| Парткод: | B065 1957 |
| Деталь: | Upper PCU Harness |
| Парткод: | B065 2494 |
| Деталь: | LED ARRAY |
| Парткод: | B234 2270 |
| Деталь: | GROUNDING PLATE |
| Парткод: | A096 2301 |
| Деталь: | Electric Potential Sensor |
| Парткод: | B247 2271 |
| Деталь: | Receptacle |
| Парткод: | B065 2392 |
| Деталь: | PCU Unit - Upper |
| Парткод: | B247 2270 |
| Деталь: | Filter:Development |
| Парткод: | B247 3340 |
| Деталь: | Pressure Release Lever |
| Парткод: | B065 2426 |
| Деталь: | SPRING |
| Парткод: | AA06 0891 |
| Деталь: | Toner Recycling Connecting Gear |
| Парткод: | AB01 1461 |
| Деталь: | Toner Recycling Gear |
| Парткод: | AB01 1462 |
| Деталь: | Shaft:Connecting:Toner Recycling |
| Парткод: | B247 2377 |
| Деталь: | BUSHING |
| Парткод: | AA08 2122 |
| Деталь: | Drum Stay |
| Парткод: | B065 2371 |
| Деталь: | OPC Drum: MT-C3 |
| Парткод: | B246 9510 |
| Деталь: | PCU:Lower:NA |
| Парткод: | B246 2261 |
| Деталь: | PCU Unit - Lower |
| Парткод: | B247 2260 |
| Деталь: | Toner Recycling Assy |
| Парткод: | B247 2395 |
| Деталь: | Front Drum Seal |
| Парткод: | AA15 2431 |
| Деталь: | Rear Drum Seal |
| Парткод: | A294 3572 |
| Деталь: | CLEANING BLADE |
| Парткод: | AD04 1140 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0037 |
| Деталь: | Driven Roller Spring |
| Парткод: | AA06 3254 |
| Деталь: | LOCK LEVER |
| Парткод: | A229 2717 |
| Деталь: | Decal - B2 |
| Парткод: | AA00 1213 |
| Деталь: | Lock Shaft |
| Парткод: | B247 2642 |
| Деталь: | Bushing - 4x6x7mm |
| Парткод: | 54 432 668 |
| Деталь: | Read Rock |
| Парткод: | A229 2655 |
| Деталь: | Rear Lock Spring |
| Парткод: | B247 2644 |
| Деталь: | Open And Close Guide Assy |
| Парткод: | B140 2647 |
| Деталь: | Front Lock |
| Парткод: | A096 2633 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2116 |
| Деталь: | Connecting Roller |
| Парткод: | AF02 0564 |
| Деталь: | Transport Roller Gear |
| Парткод: | AB01 1457 |
| Деталь: | Rubber Cushion - 1x10x10mm |
| Парткод: | A469 2123 |
| Деталь: | Exit Duplex Guide Assy |
| Парткод: | B140 2671 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA08 0034 |
| Деталь: | EXIT ROLLER SPRING |
| Парткод: | B247 2669 |
| Деталь: | Duplex Exit Roller |
| Парткод: | B247 2678 |
| Деталь: | Transport Roller:Right:Driven:Assy |
| Парткод: | B247 2643 |
| Деталь: | Paper Bank Guide Plate Assy |
| Парткод: | B140 2665 |
| Деталь: | Relay Paper Feed Harness |
| Парткод: | B065 2762 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Option Tray Guide Assy |
| Парткод: | B140 2675 |
| Деталь: | Nylon Rivet |
| Парткод: | A048 2838 |
| Деталь: | CUSHION |
| Парткод: | AA16 2079 |
| Деталь: | Open And Close Option Tray Exit Guide |
| Парткод: | B140 2673 |
| Деталь: | Harness:Manual Feed Unit:Assy |
| Парткод: | B247 2764 |
| Деталь: | Pulley - 13mm |
| Парткод: | AB03 0722 |
| Деталь: | SPRING |
| Парткод: | AA06 0890 |
| Деталь: | DC Solenoid 24V/16.5W |
| Парткод: | B247 2655 |
| Деталь: | Bracket:Tightener:Peen |
| Парткод: | B247 2754 |
| Деталь: | Gear - 22Z/39Z |
| Парткод: | AB01 7607 |
| Деталь: | Side Plate:Paper Feed:Front:Peen |
| Парткод: | B247 2605 |
| Деталь: | Front Support Plate |
| Парткод: | B065 2607 |
| Деталь: | Side Plate:Paper Feed:Rear:Peen |
| Парткод: | B247 2600 |
| Деталь: | Table Side Fence |
| Парткод: | B477 2272 |
| Деталь: | Side Fence Pad |
| Парткод: | A376 4599 |
| Деталь: | Rail - Side Fence |
| Парткод: | G564 4151 |
| Деталь: | Decal:Base:Original |
| Парткод: | B652 2354 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Original Sensor Feeler |
| Парткод: | A806 1351 |
| Деталь: | Original Sensor Feeler Stud |
| Парткод: | B477 2286 |
| Деталь: | Base:Original Table |
| Парткод: | B477 2256 |
| Деталь: | CUSHION |
| Парткод: | B477 2263 |
| Деталь: | Photointerruptor:Ee-sx4235a-p2 |
| Парткод: | AW02 0156 |
| Деталь: | Original Sensor Bracket |
| Парткод: | B477 2281 |
| Деталь: | Base Lift Lever |
| Парткод: | B477 2323 |
| Деталь: | Base Lift Shaft |
| Парткод: | B477 2322 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Original Table Guide Plate |
| Парткод: | A8061335 |
| Деталь: | Base Cushion Sheet |
| Парткод: | B477 2264 |
| Деталь: | Harness:Connecting:Sensor:Original |
| Парткод: | B477 5743 |
| Деталь: | Bushing - 8mm |
| Парткод: | 50 530 223 |
| Деталь: | Gear - Z47 |
| Парткод: | A806 2281 |
| Деталь: | Original Table:Face Front:Printing |
| Парткод: | B4771738 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Stay:Original Table:Assy |
| Парткод: | B477 2290 |
| Деталь: | Shaft:Cleaner |
| Парткод: | AA14 3789 |
| Деталь: | Spring Plate - Original Table Stopp |
| Парткод: | B477 1765 |
| Деталь: | Original Table Stopper |
| Парткод: | B477 1761 |
| Деталь: | Original Table:Behind |
| Парткод: | B4771759 |
| Деталь: | Photo Reflection Sensor:Original Table |
| Парткод: | AW01 0112 |
| Деталь: | Original Table Harness |
| Парткод: | B477 5631 |
| Деталь: | Harness:Connecting:Sensor:Base |
| Парткод: | B477 5744 |
| Деталь: | FRONT COVER |
| Парткод: | B477 1891 |
| Деталь: | Pressure Plate:Assy |
| Парткод: | B477 2721 |
| Деталь: | LOWER COVER |
| Парткод: | B477 1922 |
| Деталь: | Pressure Plate Tape |
| Парткод: | B477 2715 |
| Деталь: | Exit cover |
| Парткод: | B477 1861 |
| Деталь: | Sound Proofing Material:Cover:Rear |
| Парткод: | B477 4916 |
| Деталь: | REAR COVER |
| Парткод: | B477 1912 |
| Деталь: | Decal - Original Table |
| Парткод: | B477 4431 |
| Деталь: | SADF:DOM:Rohs:Assy |
| Парткод: | B247 7000 |
| Деталь: | STEPPED SCREW |
| Парткод: | A859 7211 |
| Деталь: | Decal - Misfeed Removal - Exit |
| Парткод: | B477 4362 |
| Деталь: | Caution Decal -CIS |
| Парткод: | B477 4381 |
| Деталь: | Turn Gear |
| Парткод: | AB01 1464 |
| Деталь: | Timing Pulley - 24Z |
| Парткод: | AB03 0583 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | PULLEY |
| Парткод: | AB01 7614 |
| Деталь: | Connecting Gear |
| Парткод: | AB01 1463 |
| Деталь: | Gear - 32Z |
| Парткод: | AB01 1496 |
| Деталь: | Pulley - 29Z |
| Парткод: | AB03 0731 |
| Деталь: | Duplex Turn Roller |
| Парткод: | AF021075 |
| Деталь: | Roller:Transport:Driven:Left:Right |
| Парткод: | B247 4812 |
| Деталь: | Timing Belt - 40S2M268G |
| Парткод: | AA04 3293 |
| Деталь: | Roller:Reversal:Drive |
| Парткод: | B247 4813 |
| Деталь: | Roller:Drive:Left |
| Парткод: | B247 4825 |
| Деталь: | Jogger Guide Rod |
| Парткод: | B065 4694 |
| Деталь: | Right Drive Roller |
| Парткод: | AF02 1079 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Brushless Motor DV24V/20.7W |
| Парткод: | B140 5325 |
| Деталь: | Stepper Motor:MM56x54:DC 36W |
| Парткод: | B247 1028 |
| Деталь: | Motor Cushion |
| Парткод: | AA16 1122 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | D0541132 |
| Деталь: | Timing Belt - S2M114 |
| Парткод: | AA04 3269 |
| Деталь: | Gear - 21Z/24T |
| Парткод: | AB01 7449 |
| Деталь: | Base:Stepper Motor:Assy |
| Парткод: | B247 1133 |
| Деталь: | Tension Spring:7.75n |
| Парткод: | B247 1027 |
| Деталь: | Pulley - 81Z |
| Парткод: | AB03 0427 |
| Деталь: | Ring - 55 |
| Парткод: | A2291135 |
| Деталь: | Fusing Drive Bracket |
| Парткод: | B065 1168 |
| Деталь: | Shaft:Fusing Drive Sub-unit |
| Парткод: | B247 1136 |
| Деталь: | Spring - 21.6mm |
| Парткод: | AA06 3490 |
| Деталь: | Fusing Drive Sub-unit Joint |
| Парткод: | B140 1173 |
| Деталь: | Bracket:Toner Recycling:Assy |
| Парткод: | B247 1157 |
| Деталь: | SPRING |
| Парткод: | AA06 6651 |
| Деталь: | Toner Recycling Tightener |
| Парткод: | B065 1160 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3946 |
| Деталь: | Brushless Motor Dc24v/24w |
| Парткод: | B247 1024 |
| Деталь: | Pulley - 89Z |
| Парткод: | AB03 0725 |
| Деталь: | Duplex Drive Bracket |
| Парткод: | A2931155 |
| Деталь: | Shaft:Drive:Duplex:Assy |
| Парткод: | B247 1166 |
| Деталь: | Duplex Drive Joint |
| Парткод: | B065 1167 |
| Деталь: | Heat Sink:Stepper Motor:Registration |
| Парткод: | D054 1039 |
| Деталь: | Harness - Switch:Laser Diode |
| Парткод: | B247 5430 |
| Деталь: | Safety Switch Lever |
| Парткод: | B065 5041 |
| Деталь: | Safety Switch Bracket |
| Парткод: | B065 5811 |
| Деталь: | Receiving Tray - Operation Panel |
| Парткод: | B065 1320 |
| Деталь: | Safety Switch Harness Cover |
| Парткод: | B065 5816 |
| Деталь: | Main Switch Bracket |
| Парткод: | B247 5715 |
| Деталь: | Duct - Fusing |
| Парткод: | B0651188 |
| Деталь: | Ips Duct |
| Парткод: | B065 1173 |
| Деталь: | Filter - Toner |
| Парткод: | B070 2114 |
| Деталь: | Duct - Charge |
| Парткод: | B0651185 |
| Деталь: | GROUNDING PLATE |
| Парткод: | B065 1845 |
| Деталь: | GROUNDING PLATE |
| Парткод: | B065 1844 |
| Деталь: | Screw:M4:Exterior |
| Парткод: | AA14 3801 |
| Деталь: | Inner Back Cam |
| Парткод: | B065 3267 |
| Деталь: | Toner Bottle Cam |
| Парткод: | B065 3266 |
| Деталь: | Upper Hinge Guide Plate |
| Парткод: | B065 1328 |
| Деталь: | Turret Spring |
| Парткод: | AA06 3052 |
| Деталь: | Hinge Shaft |
| Парткод: | B1321463 |
| Деталь: | Paper Tray:Universal:DOM:Assy |
| Парткод: | B132 6770 |
| Деталь: | Link:End Fence:Paper Size Sensor:Assy |
| Парткод: | B181 6780 |
| Деталь: | Link:Side Fence:Paper Size Sensor |
| Парткод: | B181 6789 |
| Деталь: | Spring Plate:Paper Tray:Earth |
| Парткод: | B132 6798 |
| Деталь: | Grip - Paper Tray Cover |
| Парткод: | B247 6634 |
| Деталь: | Right Support Plate |
| Парткод: | B065 6588 |
| Деталь: | Decal:Paper Tray:Paper Set Direction |
| Парткод: | B132 6786 |
| Деталь: | Decal - Positioning |
| Парткод: | B065 6545 |
| Деталь: | Decal:Paper Tray:Display:2 |
| Парткод: | AA00 3212 |
| Деталь: | Side Fence Pad |
| Парткод: | A096 6553 |
| Деталь: | Plate:Side Fence |
| Парткод: | B132 6791 |
| Деталь: | Spring Plate |
| Парткод: | A134 2978 |
| Деталь: | Positioning Stopper Lever |
| Парткод: | B065 6538 |
| Деталь: | Side Fence:Front:Assy |
| Парткод: | B132 6793 |
| Деталь: | END FENCE |
| Парткод: | AF01 7032 |
| Деталь: | Left Support Plate |
| Парткод: | B065 6589 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3005 |
| Деталь: | Tray Bottom Plate:Assy |
| Парткод: | D014 6780 |
| Деталь: | Gear:16z |
| Парткод: | AB01 2327 |
| Деталь: | Paper Tray Holder Base |
| Парткод: | B065 6591 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA00 2010 |
| Деталь: | Side Fence:Rear:Auxiliary |
| Парткод: | B132 6797 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A267 2860 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Decal:Paper Tray:Display:3 |
| Парткод: | AA00 3213 |
| Деталь: | Side Fence:Rear:Assy |
| Парткод: | B132 6795 |
| Деталь: | Arm:End Fence:Lock |
| Парткод: | B132 6783 |
| Деталь: | Tension Spring:Side Fence:Rear |
| Парткод: | AA06 0961 |
| Деталь: | Bottom Plate Lift Shaft |
| Парткод: | B065 6524 |
| Деталь: | Lift Lever |
| Парткод: | B065 6526 |
| Деталь: | Guide:Misfeed Removal:Paper Tray |
| Парткод: | B247 6695 |
| Деталь: | Paper Tray Holder Stay |
| Парткод: | B065 6581 |
| Деталь: | Paper Tray Cover - Long |
| Парткод: | B247 6632 |
| Деталь: | Paper Tray Cover - Short |
| Парткод: | B247 6633 |
| Деталь: | Tandem LCT:Right:Letter |
| Парткод: | B246 6605 |
| Деталь: | Tandem LCT:Right:Assy |
| Парткод: | B247 6605 |
| Деталь: | Right Stopper |
| Парткод: | B065 6859 |
| Деталь: | Decal - Caution |
| Парткод: | AA00 2246 |
| Деталь: | Inner Cover - Tandem LCT |
| Парткод: | B247 6745 |
| Деталь: | Protection -inner Cover |
| Парткод: | B065 6875 |
| Деталь: | Decal - Paper Set - Right |
| Парткод: | B065 6877 |
| Деталь: | Plate:Paper |
| Парткод: | B234 6690 |
| Деталь: | Side Fence:Tandem LCT:Right Front |
| Парткод: | B098 6736 |
| Деталь: | Paper Volume Sensor Bracket |
| Парткод: | B065 6706 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Friction pad |
| Парткод: | 52 012 858 |
| Деталь: | Decal - Right Paper Set |
| Парткод: | A096 6677 |
| Деталь: | Base:Tandem LCT:Right |
| Парткод: | B132 7543 |
| Деталь: | Bracket -paper Volumesensor |
| Парткод: | B065 6874 |
| Деталь: | Side Fence:Tandem LCT:Right Rear |
| Парткод: | B098 6738 |
| Деталь: | Supporting Plate:Tandem:Right Rear |
| Парткод: | B098 6739 |
| Деталь: | Shield:Tandem LCT:Rear Right |
| Парткод: | B475 6855 |
| Деталь: | Inner Cover Cushion - Right Rear |
| Парткод: | AA15 3138 |
| Деталь: | Guide:Misfeed Removal:Paper Tray |
| Парткод: | B247 6695 |
| Деталь: | Guide:Interlock:Tandem LCT |
| Парткод: | B247 6672 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA00 2010 |
| Деталь: | Side plate |
| Парткод: | A248 6666 |
| Деталь: | Sensor bracket |
| Парткод: | B065 6873 |
| Деталь: | Bushing - 6x12x4mm |
| Парткод: | A422 1078 |
| Деталь: | Discharge Brush:L11 |
| Парткод: | B477 2622 |
| Деталь: | PULLEY |
| Парткод: | B477 3245 |
| Деталь: | Timing Belt:40s2m174 |
| Парткод: | AA04 3334 |
| Деталь: | PULLEY |
| Парткод: | B477 3243 |
| Деталь: | Cis Invertor Bracket |
| Парткод: | B477 3933 |
| Деталь: | CIS Sheet |
| Парткод: | B477 2683 |
| Деталь: | CIS Sheet Bracket |
| Парткод: | B477 2682 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Reverse Roller |
| Парткод: | A859 2241 |
| Деталь: | Torque Limiter - 53mnxm |
| Парткод: | A294 6700 |
| Деталь: | Reverse Roller Shaft |
| Парткод: | B477 3131 |
| Деталь: | Inverter Roller Stay |
| Парткод: | B477 2131 |
| Деталь: | Contact Image Sensor:600DPI:Assy |
| Парткод: | B477 5860 |
| Деталь: | Exit Cis Roller |
| Парткод: | B477 2441 |
| Деталь: | Drive Exit Roller |
| Парткод: | B477 2811 |
| Деталь: | Upper Exit Guide Plate |
| Парткод: | B477 2820 |
| Деталь: | Discharge Brush:Exit |
| Парткод: | B477 2826 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A859 2230 |
| Деталь: | Transfer Unit Guide Plate |
| Парткод: | B065 3818 |
| Деталь: | Toner Collection Gear |
| Парткод: | B065 3873 |
| Деталь: | Front Arm |
| Парткод: | A229 3861 |
| Деталь: | Drive Electrode |
| Парткод: | A229 3875 |
| Деталь: | Transfer Belt - Mojito Service |
| Парткод: | A293 3899 |
| Деталь: | DRIVE ROLLER |
| Парткод: | B247 3866 |
| Деталь: | Rear Arm |
| Парткод: | A229 3862 |
| Деталь: | Transfer Unit Joint |
| Парткод: | B065 3872 |
| Деталь: | Bias Roller |
| Парткод: | B247 3870 |
| Деталь: | TERMINAL |
| Парткод: | B065 3875 |
| Деталь: | ELECTRODE PLATE |
| Парткод: | B065 3874 |
| Деталь: | PRESSURE ARM |
| Парткод: | B065 3868 |
| Деталь: | Transport Driven Roller |
| Парткод: | A229 3865 |
| Деталь: | Entrance Seal Holder |
| Парткод: | B065 3945 |
| Деталь: | Electrode:Bias |
| Парткод: | B247 3980 |
| Деталь: | Bias Terminal |
| Парткод: | B065 3878 |
| Деталь: | Grounding Bracket |
| Парткод: | B065 3950 |
| Деталь: | Stepped Screw - Locking |
| Парткод: | H053 1150 |
| Деталь: | Guide Plate Spring |
| Парткод: | AA06 3310 |
| Деталь: | GUIDE PLATE |
| Парткод: | B065 3942 |
| Деталь: | Anti-static Plate |
| Парткод: | B065 3947 |
| Деталь: | TRANSFER UNIT |
| Парткод: | B246 3854 |
| Деталь: | Front Slide Rail |
| Парткод: | A293 1674 |
| Деталь: | Pulley - 26Z |
| Парткод: | AB03 2717 |
| Деталь: | Scanner Board Guide |
| Парткод: | B065 1830 |
| Деталь: | Scanner Board Bracket |
| Парткод: | B065 1831 |
| Деталь: | Drive Were:Scanner |
| Парткод: | B247 1715 |
| Деталь: | Rear Wire Tension Bracket |
| Парткод: | B065 1713 |
| Деталь: | Gripper Solenoid Spring |
| Парткод: | AA06 0221 |
| Деталь: | REAR FRAME |
| Парткод: | B065 1685 |
| Деталь: | HP Sensor Relay Harness |
| Парткод: | B065 5454 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | H.P. Sensor Bracket |
| Парткод: | B065 1825 |
| Деталь: | Sheet - Photointerrupter |
| Парткод: | A267 1820 |
| Деталь: | PCB SDRB |
| Парткод: | B247 5180 |
| Деталь: | Bracket - Scanner Motor |
| Парткод: | B065 1706 |
| Деталь: | Cushion - Stepper Motor |
| Парткод: | A1341724 |
| Деталь: | Stepper motor |
| Парткод: | B065 1708 |
| Деталь: | TENSION SPRING |
| Парткод: | B247 1701 |
| Деталь: | Pulley:Idler:Peen |
| Парткод: | B247 1680 |
| Деталь: | Screw:Mechanical Drive Section |
| Парткод: | B132 1719 |
| Деталь: | TIMING BELT |
| Парткод: | B065 1717 |
| Деталь: | Pulley - 58Z |
| Парткод: | AB03 0727 |
| Деталь: | PULLEY |
| Парткод: | AB03 2070 |
| Деталь: | Lens Holder Block |
| Парткод: | B065 1688 |
| Деталь: | Shaft:Drive |
| Парткод: | B247 1711 |
| Деталь: | PULLEY |
| Парткод: | AB03 2069 |
| Деталь: | Front Wire Tension Bracket |
| Парткод: | B065 1712 |
| Деталь: | FRONT FRAME |
| Парткод: | B065 1682 |
| Деталь: | LD Decal |
| Парткод: | G029 1982 |
| Деталь: | Grounding Wire |
| Парткод: | B065 5471 |
| Деталь: | FFC Insulating Sheet |
| Парткод: | B140 1837 |
| Деталь: | Bracket - Paper Size Sensor |
| Парткод: | B247 6177 |
| Деталь: | Tray Lock Spring - 19mm |
| Парткод: | AA06 0534 |
| Деталь: | Tray Lock Arm |
| Парткод: | B065 6136 |
| Деталь: | Slide Rail:Left:Sub-assy |
| Парткод: | B132 6692 |
| Деталь: | Base:Slide Rail:No.3:Peen |
| Парткод: | B247 6783 |
| Деталь: | Slide Rail:Right:Assy |
| Парткод: | B132 6693 |
| Деталь: | Caster:1470n |
| Парткод: | AH01 2031 |
| Деталь: | Flanged Hexagonal Head Bolt:Caster |
| Парткод: | AA14 3803 |
| Деталь: | Hexagonal Bolt:M12x35 |
| Парткод: | AA14 3798 |
| Деталь: | Shield:Frame:Paper Bank:Upper |
| Парткод: | B098 6693 |
| Деталь: | Side Plate - Paper Tray |
| Парткод: | B065 6191 |
| Деталь: | Bracket:Positioning:Paper Tray:Assy |
| Парткод: | B247 6174 |
| Деталь: | Heater:115V:18W:Upper |
| Парткод: | AX40 0176 |
| Деталь: | Heater:240V:18W:Upper |
| Парткод: | AX40 0178 |
| Деталь: | Heat Sink:Heater:Lower:Sub-assy |
| Парткод: | B140 6221 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0010 |
| Деталь: | Harness - Paper Size Sensor |
| Парткод: | B247 6800 |
| Деталь: | Heat Sink:Heater:Lower:NA:Assy |
| Парткод: | B140 6225 |
| Деталь: | Heat Sink:Heater:Lower:EU:Assy |
| Парткод: | B140 6226 |
| Деталь: | Duct Seal - PCU |
| Парткод: | AA15 3154 |
| Деталь: | Fan bracket |
| Парткод: | B065 1183 |
| Деталь: | Entrance PCU Duct |
| Парткод: | B065 1184 |
| Деталь: | Fan Motor DC24V/1.92W |
| Парткод: | AX64 0183 |
| Деталь: | Power Pack - Development |
| Парткод: | AZ30 0057 |
| Деталь: | Bracket:Power Pack:Development |
| Парткод: | G126 5892 |
| Деталь: | Holder:Power Pack:C3 |
| Парткод: | B247 5874 |
| Деталь: | Harness - Duplex Exit |
| Парткод: | B247 5418 |
| Деталь: | Main Switch Harness Guide |
| Парткод: | B065 5818 |
| Деталь: | Harness:AC Power Supply:Main:NA |
| Парткод: | B246 5615 |
| Деталь: | Harness:AC Power Supply:Main:EU |
| Парткод: | B246 5617 |
| Деталь: | PCU Duct |
| Парткод: | B065 1180 |
| Деталь: | Harness Guide |
| Парткод: | B065 5814 |
| Деталь: | Hinge Stay - Upper |
| Парткод: | B247 5827 |
| Деталь: | CLAMP |
| Парткод: | B065 5868 |
| Деталь: | SPRING |
| Парткод: | AA06 3880 |
| Деталь: | Connector Guide Pin |
| Парткод: | AA14 3797 |
| Деталь: | Slide Rail Cover |
| Парткод: | B065 5817 |
| Деталь: | Hinge Bracket - Lower |
| Парткод: | B247 5712 |
| Деталь: | Duplex DRB Harness |
| Парткод: | B065 5422 |
| Деталь: | Compression Spring:Drawer |
| Парткод: | AA06 3901 |
| Деталь: | Finisher Cnb Harness |
| Парткод: | B065 5445 |
| Деталь: | Finisher Cable Bracket |
| Парткод: | B065 5807 |
| Деталь: | ADF Power Source Harness |
| Парткод: | B065 5447 |
| Деталь: | Bracket:Plug:ADF |
| Парткод: | B140 5891 |
| Деталь: | Upper Arm |
| Парткод: | B247 5825 |
| Деталь: | Grip - Fusing/paper Exit Unit |
| Парткод: | B247 4258 |
| Деталь: | Lock Lever Bracket |
| Парткод: | B065 4262 |
| Деталь: | Shaft:Contact Point:Lever |
| Парткод: | B247 4260 |
| Деталь: | LOCK LEVER |
| Парткод: | B247 4259 |
| Деталь: | SPRING |
| Парткод: | AA06 0903 |
| Деталь: | Lever Contact Bracket |
| Парткод: | B065 4266 |
| Деталь: | Protect Bracket Assy |
| Парткод: | B140 4470 |
| Деталь: | Cover - Exit Grip |
| Парткод: | B247 4273 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA08 0034 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B247 4455 |
| Деталь: | Exit Roller - Driven |
| Парткод: | AF02 2126 |
| Деталь: | Paper Feed Sensor Bracket |
| Парткод: | B065 4358 |
| Деталь: | Photointerruptor:Exit |
| Парткод: | AW02 0183 |
| Деталь: | Relay Harness -exit |
| Парткод: | B065 4496 |
| Деталь: | Upper Exhaust Guide Plate |
| Парткод: | B140 4354 |
| Деталь: | Upper Grip |
| Парткод: | B065 4363 |
| Деталь: | Grip Supporter |
| Парткод: | B065 4359 |
| Деталь: | Bushing - Fusing Exit |
| Парткод: | AA08 0184 |
| Деталь: | Shaft:Grip:Guide Plate |
| Парткод: | B247 4361 |
| Деталь: | Upper Exit Guide Plate |
| Парткод: | B065 4373 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | SPRING |
| Парткод: | AA06 6592 |
| Деталь: | Exit Entrance Sensor Bracket |
| Парткод: | B065 4374 |
| Деталь: | Relay Harness - Guide Plate |
| Парткод: | B065 4495 |
| Деталь: | SPRING |
| Парткод: | AA06 3879 |
| Деталь: | Bushing - MM5 |
| Парткод: | AA08 0240 |
| Деталь: | Spring Plate |
| Парткод: | B065 4360 |
| Деталь: | Roller:Decura:Driven:Assy |
| Парткод: | B247 4378 |
| Деталь: | Middle Exit Guide Plate |
| Парткод: | B065 4453 |
| Деталь: | Shaft:Contact Point:Assy |
| Парткод: | B247 4381 |
| Деталь: | Rear Fusing Plate |
| Парткод: | B065 4154 |
| Деталь: | Cover - Polygon Mirror Motor |
| Парткод: | B247 1691 |
| Деталь: | LD Decal |
| Парткод: | G029 1982 |
| Деталь: | Filter:Duct:Scanner |
| Парткод: | B065 1798 |
| Деталь: | Left Scanner Duct |
| Парткод: | B065 1791 |
| Деталь: | Right Scanner Duct |
| Парткод: | B065 1801 |
| Деталь: | Lens Unit |
| Парткод: | B247 1721 |
| Деталь: | Harness:FFC:SBU:15wick:120mm |
| Парткод: | B247 5471 |
| Деталь: | Harness:FFC:SBU:40wick:120mm |
| Парткод: | B247 5472 |
| Деталь: | Development Fan Bracket |
| Парткод: | B065 1171 |
| Деталь: | Harness Bracket |
| Парткод: | B065 1833 |
| Деталь: | Development Cooling Duct |
| Парткод: | B065 1698 |
| Деталь: | Cable - LVDC SBU |
| Парткод: | B247 5401 |
| Деталь: | Harness:Scanner Unit |
| Парткод: | B246 5650 |
| Деталь: | Harness - LCDC |
| Парткод: | B247 5405 |
| Деталь: | PCB VIB |
| Парткод: | B247 5195 |
| Деталь: | VIB Power Source Harness |
| Парткод: | B065 5501 |
| Деталь: | Fan Motor DC24V/2.88W |
| Парткод: | AX64 0182 |
| Деталь: | Development Fan Harness |
| Парткод: | B065 1172 |
| Деталь: | Insulating sheet |
| Парткод: | B065 1834 |
| Деталь: | Original Sensor:H1-66 |
| Парткод: | AW01 0116 |
| Деталь: | Pressure Tension Spring |
| Парткод: | AA06 0946 |
| Деталь: | Lever:Release:Front:Assy |
| Парткод: | B247 4131 |
| Деталь: | Lever:Front:Assy |
| Парткод: | B247 4323 |
| Деталь: | Ball Bearing - 6x15x5 |
| Парткод: | AE03 0055 |
| Деталь: | Side Plate:Fusing:Front:Assy |
| Парткод: | B247 4101 |
| Деталь: | Fusing Exit Roller |
| Парткод: | AF04 0055 |
| Деталь: | Gear:Fusing Exit |
| Парткод: | AB01 9479 |
| Деталь: | Bushing - Oil Supply Roller |
| Парткод: | AE03 1026 |
| Деталь: | Pressure Cleaning Roller Spring |
| Парткод: | B140 4200 |
| Деталь: | Fusing Cleaning Roller |
| Парткод: | AE04 2066 |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | AE03 0056 |
| Деталь: | Fusing Cleaning Roller Bracket |
| Парткод: | B140 4198 |
| Деталь: | Spring Plate - Switch |
| Парткод: | B065 4141 |
| Деталь: | Switch Holder |
| Парткод: | B065 4139 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW20 0010 |
| Деталь: | Development Cover Screw |
| Парткод: | AA14 3810 |
| Деталь: | Lower Fusing Exit Guide |
| Парткод: | B140 4140 |
| Деталь: | LEFT STAY |
| Парткод: | B065 4114 |
| Деталь: | Right Fusing Stay |
| Парткод: | B140 4112 |
| Деталь: | Side Plate:Fusing:Rear:Assy |
| Парткод: | B247 4105 |
| Деталь: | Idler Gear |
| Парткод: | AB01 2318 |
| Деталь: | Fusing Drive Gear |
| Парткод: | AB01 2317 |
| Деталь: | Lever:Rear:Assy |
| Парткод: | B247 4231 |
| Деталь: | Lever:Release:Pressure:Rear:Assy |
| Парткод: | B247 4147 |
| Деталь: | Sheet:Fiber:Side Plate |
| Парткод: | B065 4129 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2117 |
| Деталь: | Shaft - Turn |
| Парткод: | B140 4254 |
| Деталь: | Pressure Release Eccentric Cam |
| Парткод: | B140 4256 |
| Деталь: | Gear:Pressure |
| Парткод: | B247 4264 |
| Деталь: | Sensor Feeler |
| Парткод: | B140 4320 |
| Деталь: | Sensor Bracket Assy |
| Парткод: | B140 4258 |
| Деталь: | Harness - Positioning Sensor |
| Парткод: | B140 4498 |
| Деталь: | Pressure Oil Supply Roller Bracket |
| Парткод: | B140 4205 |
| Деталь: | Toner Collection Coil |
| Парткод: | B247 2326 |
| Деталь: | Agitator:Assy |
| Парткод: | B247 2322 |
| Деталь: | Toner Collection Coil Bushing |
| Парткод: | AA08 2121 |
| Деталь: | Agitator Gear |
| Парткод: | B065 2428 |
| Деталь: | Brush Roller Gear |
| Парткод: | B065 2425 |
| Деталь: | Roller Bushing |
| Парткод: | AA08 2119 |
| Деталь: | Brush Roller:Cleaning |
| Парткод: | B247 2330 |
| Деталь: | Shaft:Brush Roller:Front:Assy |
| Парткод: | B247 2366 |
| Деталь: | Spacer - M6 |
| Парткод: | AA13 2208 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA082101 |
| Деталь: | Bushing - Brush Roller |
| Парткод: | AA08 2094 |
| Деталь: | Inner Case Seal |
| Парткод: | AA15 3085 |
| Деталь: | Idler Gear |
| Парткод: | AB01 1460 |
| Деталь: | Cam - Blade |
| Парткод: | B065 2427 |
| Деталь: | Cleaning Entrance Seal - 3x345x2 |
| Парткод: | AA15 3088 |
| Деталь: | Bracket:Swivel:Blade:Assy |
| Парткод: | B247 2353 |
| Деталь: | Toner Collection Coil Gear |
| Парткод: | AB01 1459 |
| Деталь: | Pre-transfer Lamp Harness Plate |
| Парткод: | B140 2421 |
| Деталь: | Entrance Transfer Stay Assy |
| Парткод: | B140 2413 |
| Деталь: | GEAR |
| Парткод: | AB01 7612 |
| Деталь: | Pre-transfer Lamp Case Assy |
| Парткод: | B140 2382 |
| Деталь: | LED ARRAY |
| Парткод: | B234 2270 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Gear - Z18 |
| Парткод: | A806 2271 |
| Деталь: | Timing Pulley - T19/Z23 S2M/M0.6 |
| Парткод: | A806 2151 |
| Деталь: | Pick-up Roller Bracket |
| Парткод: | B477 2222 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | B477 2225 |
| Деталь: | Spacer - 6x20x1 |
| Парткод: | AA132171 |
| Деталь: | Timing Belt:40S2M148 |
| Парткод: | AA04 3335 |
| Деталь: | Pick-up Roller Lever |
| Парткод: | B477 2231 |
| Деталь: | Rear Entrance Guide |
| Парткод: | B477 2182 |
| Деталь: | Guide Plate Cushion |
| Парткод: | A806 1163 |
| Деталь: | Timing Pulley - T27 S2M |
| Парткод: | A806 2153 |
| Деталь: | Bushing - 8mm |
| Парткод: | A628 1225 |
| Деталь: | Separation Shaft |
| Парткод: | B477 2191 |
| Деталь: | Feed Belt Drive Roller |
| Парткод: | A8061293 |
| Деталь: | Feed-in Unit Stopper |
| Парткод: | A680 1621 |
| Деталь: | Front Entrance Guide |
| Парткод: | B477 2172 |
| Деталь: | SPACER |
| Парткод: | AA13 2013 |
| Деталь: | Compression Spring:Paper FeedJoint |
| Парткод: | AA06 3435 |
| Деталь: | Spacer - M6.5x1 |
| Парткод: | A418 1158 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | B301 1286 |
| Деталь: | Feed Belt |
| Парткод: | A8061295 |
| Деталь: | SPRING BELT GUIDE ROLLER |
| Парткод: | A806 4261 |
| Деталь: | Feed Belt Bracket |
| Парткод: | A806 1292 |
| Деталь: | Transport Belt Roller Shaft |
| Парткод: | A8061298 |
| Деталь: | Feed Belt Driven Roller |
| Парткод: | A806 1294 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Pickup Roller:Coupling |
| Парткод: | B477 2227 |
| Деталь: | IPU Bracket |
| Парткод: | B247 5862 |
| Деталь: | PCB:Image Processing Unit:Basic:Martini-C3 |
| Парткод: | B247 5141 |
| Деталь: | Harness - SBU |
| Парткод: | B247 5452 |
| Деталь: | Harness - CIS |
| Парткод: | B247 5455 |
| Деталь: | Harness - LDB |
| Парткод: | B247 5454 |
| Деталь: | Harness - Sync Detector |
| Парткод: | B247 5453 |
| Деталь: | Harness - LDB Power Source |
| Парткод: | B247 5456 |
| Деталь: | Harness - IPU BCU |
| Парткод: | B247 5451 |
| Деталь: | Bracket - Mother Board HDD |
| Парткод: | B247 5889 |
| Деталь: | Bracket - Mother Board PSU |
| Парткод: | B247 5891 |
| Деталь: | Insulating Sheet - HDD |
| Парткод: | B247 5836 |
| Деталь: | Insulating Sheet - Power Source |
| Парткод: | B247 5837 |
| Деталь: | Harness - Mb Operation Panel |
| Парткод: | B247 5457 |
| Деталь: | PCB:March3_2nd |
| Парткод: | B247 5205 |
| Деталь: | PCB DDR-DIMM 128Mb |
| Парткод: | B234 5563 |
| Деталь: | Cover - Image Processing Unit |
| Парткод: | B247 5864 |
| Деталь: | Harness Bracket |
| Парткод: | B247 5863 |
| Деталь: | Cover - HDD |
| Парткод: | B247 5868 |
| Деталь: | Connector Side Plate Bracket |
| Парткод: | B247 5884 |
| Деталь: | Harness - Upper |
| Парткод: | B247 5416 |
| Деталь: | PCB:BCU:Service |
| Парткод: | D054 5122 |
| Деталь: | PCB:IOB |
| Парткод: | D054 5128 |
| Деталь: | BCU Bracket |
| Парткод: | B247 5711 |
| Деталь: | Harness - Left |
| Парткод: | B247 5417 |
| Деталь: | Front Side Plate |
| Парткод: | B477 1111 |
| Деталь: | Rear Side Plate |
| Парткод: | B477 1121 |
| Деталь: | Motor Bracket Cushion |
| Парткод: | B477 2333 |
| Деталь: | Arm Shaft |
| Парткод: | B477 1171 |
| Деталь: | Release Spring Holder |
| Парткод: | AA14 3832 |
| Деталь: | Spring Plate - 0.4mm |
| Парткод: | B301 1136 |
| Деталь: | Stay:Frame:Left |
| Парткод: | B4771152 |
| Деталь: | CLAMP |
| Парткод: | B477 4921 |
| Деталь: | Hinge:Left:Assy |
| Парткод: | B477 1561 |
| Деталь: | Contact Point Shaft |
| Парткод: | A806 1135 |
| Деталь: | Right Frame Stay |
| Парткод: | B477 1161 |
| Деталь: | Hinge:Right:Assy |
| Парткод: | B477 1571 |
| Деталь: | Sensor Feeler |
| Парткод: | B4771185 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Sensor bracket |
| Парткод: | B477 1181 |
| Деталь: | DC Solenoid:End Fence:Front:Assy |
| Парткод: | B132 7547 |
| Деталь: | Lever:Release:Front |
| Парткод: | B070 6683 |
| Деталь: | Tension Spring - Short |
| Парткод: | AA06 0758 |
| Деталь: | Hook - Tension Sprong |
| Парткод: | A248 6713 |
| Деталь: | Tension Spring - Long |
| Парткод: | AA06 0757 |
| Деталь: | End Fence - Front |
| Парткод: | B247 6713 |
| Деталь: | End Fence Guide |
| Парткод: | B065 6712 |
| Деталь: | Detector Bracket |
| Парткод: | B065 6881 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | End Fence - Rear |
| Парткод: | B247 6714 |
| Деталь: | Detector Bracket |
| Парткод: | B065 6884 |
| Деталь: | DC Solenoid:End Fence:Rear:Assy |
| Парткод: | B132 7571 |
| Деталь: | Side Plate:Tandem LCT:Right Rear:Assy |
| Парткод: | B247 6811 |
| Деталь: | Lever:Release:Rear |
| Парткод: | B070 6684 |
| Деталь: | Wire Pulley - M10 |
| Парткод: | AB03 2058 |
| Деталь: | Guide - Pulley |
| Парткод: | A248 6695 |
| Деталь: | Pulley - M10 |
| Парткод: | AB03 2719 |
| Деталь: | Shaft:Drive:Tray Bottom Plate:Right:Press Fit |
| Парткод: | B247 6958 |
| Деталь: | Pulley:Drive Were:Assy |
| Парткод: | B247 6694 |
| Деталь: | Bushing - 8mm |
| Парткод: | 50 530 223 |
| Деталь: | Harness - Tandem LCT Right |
| Парткод: | B247 6703 |
| Деталь: | Right Bracket |
| Парткод: | B065 6743 |
| Деталь: | Large Lever |
| Парткод: | B065 6862 |
| Деталь: | Spacer - 6mm |
| Парткод: | AA13 2203 |
| Деталь: | SENSOR |
| Парткод: | AW01 0113 |
| Деталь: | Cushion - Large |
| Парткод: | AA16 1129 |
| Деталь: | Base:Tandem LCT:Right:Welding |
| Парткод: | B132 7545 |
| Деталь: | Roller - Slide Rail |
| Парткод: | AF02 2105 |
| Деталь: | Cushion - Small |
| Парткод: | AA16 1130 |
| Деталь: | Small Lever |
| Парткод: | B065 6864 |
| Деталь: | Wire Ring |
| Парткод: | A248 6694 |
| Деталь: | Stay -rightbase |
| Парткод: | B065 6870 |
| Деталь: | Feeler - Paper Height Sensor |
| Парткод: | A294 6690 |
| Деталь: | Paper Volume Shield Plate |
| Парткод: | B065 6717 |
| Деталь: | Side Plate:Tandem LCT:Front Right:Assy |
| Парткод: | B247 6955 |
| Деталь: | OIL DAMPER |
| Парткод: | A248 6701 |
| Деталь: | Gear -30Z |
| Парткод: | AB01 3781 |
| Деталь: | Oil Damper Bracket |
| Парткод: | B065 6872 |
| Деталь: | Front Roller - Slide Rail |
| Парткод: | A294 6655 |
| Деталь: | Cushion - Motor |
| Парткод: | AA16 1104 |
| Деталь: | Fan Bracket - IPS |
| Парткод: | B065 1178 |
| Деталь: | Duct Seal - IPS |
| Парткод: | AA15 3155 |
| Деталь: | Entrance IPS Duct |
| Парткод: | B065 1175 |
| Деталь: | Sirocco Fan Motor DC24V/8W |
| Парткод: | B247 1095 |
| Деталь: | CSS Bracket |
| Парткод: | B065 5805 |
| Деталь: | Upper Ips Duct |
| Парткод: | B065 1177 |
| Деталь: | Exhaust Bracket |
| Парткод: | B065 1194 |
| Деталь: | Upper Exhaust Duct |
| Парткод: | B065 1192 |
| Деталь: | Lower Exhaust Duct |
| Парткод: | B065 1193 |
| Деталь: | Exhaust Duct Seal |
| Парткод: | AA15 3156 |
| Деталь: | Sirocco Fan Motor DC24V/8.5W |
| Парткод: | AX65 0044 |
| Деталь: | Power Pack - Charactor Generator |
| Парткод: | AZ32 0163 |
| Деталь: | Charge Power Pack Bracket |
| Парткод: | B065 5804 |
| Деталь: | Harness - DC PSU CNB BCU |
| Парткод: | B247 5500 |
| Деталь: | Harness - Power Source BCU DRB |
| Парткод: | B140 5509 |
| Деталь: | Harness - Safety Switch |
| Парткод: | B247 5421 |
| Деталь: | PCB CNB |
| Парткод: | B247 5230 |
| Деталь: | Harness - CNB Upper |
| Парткод: | B247 5420 |
| Деталь: | CNB Bracket |
| Парткод: | B140 5802 |
| Деталь: | PCB DRB |
| Парткод: | B247 5185 |
| Деталь: | DRB Bracket |
| Парткод: | B140 5803 |
| Деталь: | VIB Power Source Harness |
| Парткод: | B065 5501 |
| Деталь: | ADF/CNB Harness |
| Парткод: | B065 5503 |
| Деталь: | Screw:M4:Exterior |
| Парткод: | AA14 3801 |
| Деталь: | Door Switch Bracket |
| Парткод: | A294 1292 |
| Деталь: | Decal:Misfeed Removal:Main |
| Парткод: | B247 1361 |
| Деталь: | Stand:Auxiliary:Assy |
| Парткод: | B247 8701 |
| Деталь: | Hinge:Upper |
| Парткод: | B098 1342 |
| Деталь: | Decal - Toner Supply |
| Парткод: | B065 1366 |
| Деталь: | FRONT DOOR ASSY |
| Парткод: | B247 1224 |
| Деталь: | Door Catch |
| Парткод: | B132 1526 |
| Деталь: | Cover - Main Switch |
| Парткод: | B247 1325 |
| Деталь: | Hinge:Lower:Assy |
| Парткод: | B247 1223 |
| Деталь: | Guide Plate Lever |
| Парткод: | B065 1323 |
| Деталь: | Micro Switchlever |
| Парткод: | B065 1326 |
| Деталь: | Panel:Logo |
| Парткод: | B132 1531 |
| Деталь: | Decal - Main Switch:NA |
| Парткод: | B065 1363 |
| Деталь: | Decal - Main Switch:EU |
| Парткод: | B065 1364 |
| Деталь: | Inner Cover - Main Switch |
| Парткод: | B247 1315 |
| Деталь: | Inner Cover - Fusing Unit Upper |
| Парткод: | B247 1316 |
| Деталь: | Decal - Lever Release Transfer |
| Парткод: | B234 3892 |
| Деталь: | Inner cover |
| Парткод: | B247 1313 |
| Деталь: | Fan Motor DC24V/1.68W |
| Парткод: | AX64 0176 |
| Деталь: | PCU Duct Inner Cover |
| Парткод: | B065 1318 |
| Деталь: | Knob - Duplex |
| Парткод: | AG05 0102 |
| Деталь: | Decal - Total Counter |
| Парткод: | B234 1378 |
| Деталь: | CD-ROM:Manual1:AA (-29) |
| Парткод: | D054 7319 |
| Деталь: | CD-ROM:Manual2:AA (-29) |
| Парткод: | D054 7320 |
| Деталь: | Inner Cover - Right Lower |
| Парткод: | B247 1314 |
| Деталь: | INNER COVER ASSY |
| Парткод: | B247 3290 |
| Деталь: | Sheet:Model Name Plate:D052:RIC |
| Парткод: | D052 7012 |
| Деталь: | Sheet:Model Name Plate:D052:GES:NA |
| Парткод: | D052 7033 |
| Деталь: | Sheet:Model Name Plate:D052:GES:EU |
| Парткод: | D052 7015 |
| Деталь: | Sheet:Model Name Plate:D052:NSA |
| Парткод: | D052 7016 |
| Деталь: | Sheet:Model Name Plate:D052:REX |
| Парткод: | D052 7017 |
| Деталь: | Sheet:Model Name Plate:D052:INF |
| Парткод: | D052 7019 |
| Деталь: | Sheet:Model Name Plate:D052:SAV |
| Парткод: | D052 7032 |
| Деталь: | Sheet:Model Name Plate:D052:LAN:NA |
| Парткод: | D052 7034 |
| Деталь: | Sheet:Model Name Plate:D052:LAN EU |
| Парткод: | D052 7028 |
| Деталь: | Sheet:Model Name Plate:D053:RIC |
| Парткод: | D053 7012 |
| Деталь: | Sheet:Model Name Plate:D053:GES:NA |
| Парткод: | D053 7033 |
| Деталь: | Sheet:Model Name Plate:D053:GES:EU |
| Парткод: | D053 7015 |
| Деталь: | Sheet:Model Name Plate:D053:NSA |
| Парткод: | D053 7016 |
| Деталь: | Sheet:Model Name Plate:D053:REX |
| Парткод: | D053 7017 |
| Деталь: | Sheet:Model Name Plate:D053:INF |
| Парткод: | D053 7019 |
| Деталь: | Sheet:Model Name Plate:D053:SAV |
| Парткод: | D053 7032 |
| Деталь: | Sheet:Model Name Plate:D053:LAN:NA |
| Парткод: | D053 7034 |
| Деталь: | Sheet:Model Name Plate:D053:LAN:EU |
| Парткод: | D053 7028 |
| Деталь: | Sheet:Model Name Plate:D054:RIC |
| Парткод: | D054 7012 |
| Деталь: | Sheet:Model Name Plate:D054:GES:NA |
| Парткод: | D054 7033 |
| Деталь: | Sheet:Model Name Plate:D054:GES:EU |
| Парткод: | D054 7015 |
| Деталь: | Sheet:Model Name Plate:D054:NSA |
| Парткод: | D054 7016 |
| Деталь: | Sheet:Model Name Plate:D054:REX |
| Парткод: | D054 7017 |
| Деталь: | Sheet:Model Name Plate:D054:INF |
| Парткод: | D054 7019 |
| Деталь: | Sheet:Model Name Plate:D054:SAV |
| Парткод: | D054 7032 |
| Деталь: | Sheet:Model Name Plate:D054:LAN:NA |
| Парткод: | D054 7034 |
| Деталь: | Sheet:Model Name Plate:D054:LAN:EU |
| Парткод: | D054 7028 |
| Деталь: | Nut - M3.6 |
| Парткод: | AA10 0006 |
| Деталь: | Inner cover |
| Парткод: | B247 6184 |
| Деталь: | O/I Holder - Assembly |
| Парткод: | B027 8521 |
| Деталь: | Holder:Stand |
| Парткод: | B132 1226 |
| Деталь: | Cloth Holder |
| Парткод: | B065 1371 |
| Деталь: | Decal:Toner:Supply:Operation Sub-Unit:EXP |
| Парткод: | B246 3342 |
| Деталь: | Decal:Toner:Supply:Operation Sub-Unit:DEU |
| Парткод: | B246 3345 |
| Деталь: | Decal:Toner:Supply:Operation Sub-Unit:FRA |
| Парткод: | B246 3346 |
| Деталь: | Decal:Toner:Supply:Operation Sub-Unit:ITA |
| Парткод: | B246 3347 |
| Деталь: | Decal:Toner:Supply:Operation Sub-Unit:ESP |
| Парткод: | B246 3348 |
| Деталь: | Manual:Copy_REF:AA (-29) |
| Парткод: | D052 7255 |
| Деталь: | Manual:TROUBLESHOOT:AA (-29) |
| Парткод: | D052 7453 |
| Деталь: | Decal:Size Indication:Multi-Language:C3 |
| Парткод: | B234 8510 |
| Деталь: | Decal:Power Source:Off:Exp |
| Парткод: | B082 6403 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | B0701307 |
| Деталь: | Cloth - DF Exposure Glass |
| Парткод: | B065 1374 |
| Деталь: | Decal - Cleaning |
| Парткод: | B477 4371 |
| Деталь: | Sheet:Data:Display:MT-C3:NA |
| Парткод: | B247 1441 |
| Деталь: | Sheet:Data:Display:MT-C3:EU |
| Парткод: | B247 1471 |
| Деталь: | Sheet:User Cautions:DHCP |
| Парткод: | B361 8533 |
| Деталь: | Decal:Exposure Glass:5-lang |
| Парткод: | G564 6077 |
| Деталь: | Decal:D1/E1:Multi |
| Парткод: | B065 4276 |
| Деталь: | Front Left Stopper |
| Парткод: | B477 1191 |
| Деталь: | Shaft:Cleaner |
| Парткод: | AA14 3789 |
| Деталь: | SPRING |
| Парткод: | B477 4121 |
| Деталь: | SPRING |
| Парткод: | B477 4123 |
| Деталь: | Front Scanning Bracket |
| Парткод: | B477 1131 |
| Деталь: | Scanning Guide Plate |
| Парткод: | B477 2517 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Scanning Roller |
| Парткод: | B477 2511 |
| Деталь: | Front Scanning Arm |
| Парткод: | B477 2431 |
| Деталь: | Front Scanning Roller Arm |
| Парткод: | B477 2425 |
| Деталь: | Drive Scanning Roller |
| Парткод: | B477 2421 |
| Деталь: | Rear Scanning Bracket |
| Парткод: | B477 1141 |
| Деталь: | DISCHARGE BRUSH:GUIDE PLATE |
| Парткод: | B477 2882 |
| Деталь: | Rear Lever Shaft - Misffed Removal |
| Парткод: | B477 2451 |
| Деталь: | Discharge Brush |
| Парткод: | B477 2518 |
| Деталь: | SPRING |
| Парткод: | B477 4125 |
| Деталь: | Front Lock Hook - CIS |
| Парткод: | B477 2455 |
| Деталь: | Paper Feed Sensor Bracket |
| Парткод: | B477 2495 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B477 2491 |
| Деталь: | Upper Exit Scanning Guide Plate |
| Парткод: | B477 2480 |
| Деталь: | Upper Exit Scanning Sheet |
| Парткод: | B477 2487 |
| Деталь: | Scanning Roller Cover |
| Парткод: | B477 2521 |
| Деталь: | Timing Belt:60S2M168 |
| Парткод: | AA04 3333 |
| Деталь: | Reverse Knob |
| Парткод: | B065 4866 |
| Деталь: | SPRING |
| Парткод: | AA06 2318 |
| Деталь: | Shoulder Screw - Front Cover |
| Парткод: | AA143129 |
| Деталь: | Invertor Lever |
| Парткод: | B065 4647 |
| Деталь: | Lower Entrance Guide Plate |
| Парткод: | A229 4623 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B247 4817 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA08 0034 |
| Деталь: | Roller:Driven:Duplex |
| Парткод: | B247 4624 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2116 |
| Деталь: | Front Side Plate |
| Парткод: | B065 4627 |
| Деталь: | TENSION SPRING |
| Парткод: | B247 4816 |
| Деталь: | SPACER |
| Парткод: | B247 4615 |
| Деталь: | Front Gate Pawl |
| Парткод: | A293 4613 |
| Деталь: | Gate Pawl:Reverse |
| Парткод: | B247 4645 |
| Деталь: | Rear Gate Pawl |
| Парткод: | A293 4614 |
| Деталь: | Reverse Roller:Entrance |
| Парткод: | B247 4818 |
| Деталь: | Side Plate:Rear:Reverse Unit:Assy |
| Парткод: | B247 4620 |
| Деталь: | Joint Holder |
| Парткод: | B065 4632 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B247 4815 |
| Деталь: | Drive Joint |
| Парткод: | A229 4740 |
| Деталь: | Sensor bracket |
| Парткод: | B065 4644 |
| Деталь: | Duplex Discharge Brush |
| Парткод: | A229 4617 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0119 |
| Деталь: | Upper Entrance Guide Plate Assy |
| Парткод: | B140 4640 |
| Деталь: | Stopped Screw - M4x17 |
| Парткод: | AA14 3426 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | LEVER CAM |
| Парткод: | B065 4648 |
| Деталь: | Original Sensor:H3-80 |
| Парткод: | AW01 0130 |
| Деталь: | Seal - 90x29.5x0.2 |
| Парткод: | AA15 0704 |
| Деталь: | Scale Bracket |
| Парткод: | B065 1787 |
| Деталь: | SEAL |
| Парткод: | B065 1782 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 54 421 924 |
| Деталь: | Sheet Through Exposure Glass |
| Парткод: | BC01 2003 |
| Деталь: | Left Scale |
| Парткод: | B065 1772 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | HEATER:120V:9W |
| Парткод: | B246 1835 |
| Деталь: | Heater:230V:9W |
| Парткод: | B246 1836 |
| Деталь: | Scale:Sheet Through:NA |
| Парткод: | B246 1775 |
| Деталь: | Scale - Sheet Through |
| Парткод: | B247 1776 |
| Деталь: | GROUNDING PLATE |
| Парткод: | B065 1843 |
| Деталь: | Scale Bracket Seal |
| Парткод: | B065 1773 |
| Деталь: | Exposure Glass |
| Парткод: | AC01 2067 |
| Деталь: | ADF Bracket |
| Парткод: | B065 1093 |
| Деталь: | Scale - Rear |
| Парткод: | B247 1788 |
| Деталь: | RIGHT STAY |
| Парткод: | B065 1785 |
| Деталь: | Inner cover |
| Парткод: | B065 1841 |
| Деталь: | Decal:Scale:NA |
| Парткод: | B246 1779 |
| Деталь: | Decal:Scale |
| Парткод: | B247 1778 |
| Деталь: | Cover - Tandem LCT |
| Парткод: | B247 6630 |
| Деталь: | Decal:Paper Tray:Display:1 |
| Парткод: | AA00 3211 |
| Деталь: | Tandem LCT:Left:Letter |
| Парткод: | B246 6615 |
| Деталь: | Tandem LCT Unit - Left |
| Парткод: | B247 6603 |
| Деталь: | Bracket:Cover:Tandem LCT |
| Парткод: | B098 6646 |
| Деталь: | Decal - Paper Set - Left |
| Парткод: | B065 6846 |
| Деталь: | End Fence:Auxiliary |
| Парткод: | B098 6647 |
| Деталь: | Side Plate:Tandem LCT:Left Sideways |
| Парткод: | B098 6645 |
| Деталь: | Side Fence:Tandem LCT:Left Front |
| Парткод: | B098 6643 |
| Деталь: | Tray Bottom Plate:Left Front |
| Парткод: | B098 6640 |
| Деталь: | Tray Bottom Plate:Left Middle:Assy |
| Парткод: | B098 6639 |
| Деталь: | Tray Bottom Plate:Left Rear |
| Парткод: | B098 6642 |
| Деталь: | Decal - Left Paper Set |
| Парткод: | A096 6678 |
| Деталь: | Sensor bracket |
| Парткод: | B065 6831 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA00 2010 |
| Деталь: | Side Fence:Tandem LCT:Left Rear |
| Парткод: | B098 6644 |
| Деталь: | Cover:Rear:Tandem LCT:Assy |
| Парткод: | B098 6649 |
| Деталь: | Rear Cover Cushion - Tandem LCT |
| Парткод: | A293 6649 |
| Деталь: | Back Fence - Left |
| Парткод: | B247 6624 |
| Деталь: | Timing Belt Cover |
| Парткод: | B065 6823 |
| Деталь: | Timing Pulley - 15T |
| Парткод: | AB03 3085 |
| Деталь: | Shaft:Slider:Back Fence |
| Парткод: | B247 6950 |
| Деталь: | Slider:Back Fence:Left |
| Парткод: | B132 7564 |
| Деталь: | Pulley Bracket |
| Парткод: | B065 6830 |
| Деталь: | Timing Belt S3M 196T |
| Парткод: | AA04 3271 |
| Деталь: | Coupling Lever - Left |
| Парткод: | A248 6615 |
| Деталь: | Harness - Tandem LCT Left |
| Парткод: | B247 6701 |
| Деталь: | Timing Pulley - 15T |
| Парткод: | AB03 3084 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Shaft - Timing Pulley |
| Парткод: | AA14 0686 |
| Деталь: | Gear - 48T |
| Парткод: | AB01 9475 |
| Деталь: | Tension Spring - 10n |
| Парткод: | B247 6755 |
| Деталь: | Bracket:Pulley:Driven:Assy |
| Парткод: | B247 6951 |
| Деталь: | Left DC Motor Bracket |
| Парткод: | B070 6666 |
| Деталь: | DC Motor:Tandem LCT |
| Парткод: | AX04 0145 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Gear - Z18 |
| Парткод: | AB01 3798 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0163 |
| Деталь: | Base:Tandem LCT:Left:Assy |
| Парткод: | B247 6970 |
| Деталь: | Grip - Paper Tray Cover |
| Парткод: | B247 6634 |
| Деталь: | Bracket:Arm:Assy |
| Парткод: | B132 6726 |
| Деталь: | Spacer - 6mm |
| Парткод: | AA13 2203 |
| Деталь: | LOCK ARM |
| Парткод: | B065 6769 |
| Деталь: | Lock Spring - Small |
| Парткод: | B247 6754 |
| Деталь: | Lock Spring - Large |
| Парткод: | B247 6753 |
| Деталь: | DC Motor:Rise:Tandem LCT:Assy |
| Парткод: | B132 6759 |
| Деталь: | DC Solenoid:Lock:Assy |
| Парткод: | B132 6765 |
| Деталь: | DC Motor:Rise:Paper Tray |
| Парткод: | AX04 0144 |
| Деталь: | Right Connecting Bracket |
| Парткод: | B065 6767 |
| Деталь: | Harness:Bank:Rear:Three Way |
| Парткод: | B247 5700 |
| Деталь: | SPRING |
| Парткод: | AA06 3880 |
| Деталь: | Connector Guide Pin |
| Парткод: | AA14 3797 |
| Деталь: | Bracket:Connector:Left |
| Парткод: | B132 6763 |
| Деталь: | Upper PSU Stay |
| Парткод: | B065 5878 |
| Деталь: | DC Solenoid:Coupling:Assy |
| Парткод: | B132 6762 |
| Деталь: | Harness:Bank:Rear:Three Way |
| Парткод: | B247 5709 |
| Деталь: | Compression Spring:Drawer |
| Парткод: | AA06 3901 |
| Деталь: | Paper Tray Stopper |
| Парткод: | B065 6172 |
| Деталь: | Operation Sub-unit:M-C3:Basic:NA:Assy |
| Парткод: | B246 1404 |
| Деталь: | Operation Sub-unit:Basic:EU |
| Парткод: | B246 1406 |
| Деталь: | Keytop - Copy NA |
| Парткод: | B223 1528 |
| Деталь: | Keytop:Copy:EU |
| Парткод: | B223 1534 |
| Деталь: | Keytop - Doc NA |
| Парткод: | B223 1529 |
| Деталь: | Keytop:Doc:EU |
| Парткод: | B223 1535 |
| Деталь: | Keytop - Blank FB |
| Парткод: | B223 1518 |
| Деталь: | DIAL |
| Парткод: | B238 1521 |
| Деталь: | Cover:Volume:Lower |
| Парткод: | B238 1522 |
| Деталь: | Lens - Front |
| Парткод: | B247 1431 |
| Деталь: | Spacer - Keytop |
| Парткод: | B2381547 |
| Деталь: | Keytop - Counter |
| Парткод: | B238 1511 |
| Деталь: | Harness:OP-L:12 |
| Парткод: | D0091482 |
| Деталь: | Harness:OP-L:13 |
| Парткод: | D0091483 |
| Деталь: | PCB OP-L |
| Парткод: | B238 1475 |
| Деталь: | PCB OP-R |
| Парткод: | B238 1470 |
| Деталь: | Harness - OP-R 13p |
| Парткод: | B238 1481 |
| Деталь: | Harness - OP-R 10p |
| Парткод: | B238 1480 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B223 1520 |
| Деталь: | Keytop:10key:NA |
| Парткод: | B223 1540 |
| Деталь: | Keytop:10key |
| Парткод: | B223 1521 |
| Деталь: | Keytop - 10key AA |
| Парткод: | B223 1541 |
| Деталь: | Keytop - Clear Modes |
| Парткод: | B2381583 |
| Деталь: | Keytop - Start |
| Парткод: | B238 1504 |
| Деталь: | Keytop - Try Print |
| Парткод: | B238 1506 |
| Деталь: | Keytop - Interrupt |
| Парткод: | B2381509 |
| Деталь: | Keytop - Kantan |
| Парткод: | B238 1552 |
| Деталь: | Keytop - Login |
| Парткод: | B2381550 |
| Деталь: | Keytop - Power Source |
| Парткод: | B2381549 |
| Деталь: | Shadeing Plate - Touch Panel |
| Парткод: | B2381557 |
| Деталь: | Touch Panel - W-VGA M |
| Парткод: | B223 1488 |
| Деталь: | Cable FFC LCD |
| Парткод: | B238 1487 |
| Деталь: | LCD STN W-VGA |
| Парткод: | B238 1485 |
| Деталь: | LCD Spacer A |
| Парткод: | B238 1534 |
| Деталь: | LCD Spacer B |
| Парткод: | B2381535 |
| Деталь: | Bracket:LCDC:M-C3:EU:Assy |
| Парткод: | B247 1475 |
| Деталь: | INSULATOR |
| Парткод: | B2381533 |
| Деталь: | Invertor STN |
| Парткод: | B238 1486 |
| Деталь: | Harness - Invertor |
| Парткод: | B238 1484 |
| Деталь: | PCB:LCDC:NA |
| Парткод: | B247 1461 |
| Деталь: | PCB:LCDC:EU |
| Парткод: | B247 1462 |
| Деталь: | PCB:M-C3:LCDC:TWN/AA:Assy |
| Парткод: | B246 1460 |
| Деталь: | Keytop:Function:NA (D052/D053/D054 Model 57) |
| Парткод: | B223 1533 |
| Деталь: | Keytop:Printer:M-C3:NA (D052/D053/D054 Model 57) |
| Парткод: | B247 1447 |
| Деталь: | Keytop:Scanner:M-C3:NA (D052/D053/D054 Model 57) |
| Парткод: | B247 1448 |
| Деталь: | Keytop:Touroku:M-C3:NA (D052/D053/D054 Model 57) |
| Парткод: | B247 1449 |
| Деталь: | Keytop:Printer:M-C3:EU (D052/D053/D054 Model 68/69) |
| Парткод: | B247 1457 |
| Деталь: | Keytop:Scanner:M-C3:EU (D052/D053/D054 Model 68/69) |
| Парткод: | B247 1458 |
| Деталь: | Development Unit |
| Парткод: | B247 3050 |
| Деталь: | Development Guide Rail |
| Парткод: | B065 3095 |
| Деталь: | Shield - Drum Front |
| Парткод: | B140 3099 |
| Деталь: | Entrance Seal Assy |
| Парткод: | B1103091 |
| Деталь: | Development Bias Plate |
| Парткод: | B065 3082 |
| Деталь: | Shield - Drum Rear |
| Парткод: | B140 3100 |
| Деталь: | Development Knob |
| Парткод: | B065 3071 |
| Деталь: | Gear - 41Z |
| Парткод: | B065 3076 |
| Деталь: | Toner Sensor Guide |
| Парткод: | B065 3065 |
| Деталь: | TONER DENSITY SENSOR |
| Парткод: | B247 5310 |
| Деталь: | Gear - 17Z |
| Парткод: | B065 3098 |
| Деталь: | Gear - 31Z |
| Парткод: | B065 3073 |
| Деталь: | Gear - 25Z |
| Парткод: | AB01 3790 |
| Деталь: | Gear - 20Z |
| Парткод: | B065 3096 |
| Деталь: | Gear - 21Z |
| Парткод: | B065 3081 |
| Деталь: | Ball Bearing Bracket |
| Парткод: | B065 3079 |
| Деталь: | Filter:Development |
| Парткод: | B247 3340 |
| Деталь: | Development Filter Case |
| Парткод: | A096 3141 |
| Деталь: | Filter Plate |
| Парткод: | B065 3108 |
| Деталь: | Development Screw |
| Парткод: | A294 3116 |
| Деталь: | Developer Type 24 Black |
| Парткод: | B064 9640 |
| Деталь: | Paper Feed Unit:Paper Bank |
| Парткод: | B132 6621 |
| Деталь: | Paper Bank Connecting Guide Plate |
| Парткод: | B140 6361 |
| Деталь: | Harness - Joint Unit |
| Парткод: | B132 7583 |
| Деталь: | Stepper Motor:Paper Feed Unit:Assy |
| Парткод: | B132 6655 |
| Деталь: | Transport Roller:Drive:Grip |
| Парткод: | AF02 0726 |
| Деталь: | Gear - 35Z |
| Парткод: | AB01 1466 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3575 |
| Деталь: | Gear - 24Z/40Z |
| Парткод: | AB01 7619 |
| Деталь: | Joint Unit Guide Plate Assy |
| Парткод: | B140 6472 |
| Деталь: | SPRING |
| Парткод: | AA06 3878 |
| Деталь: | Cover:Release:Vertical Transport |
| Парткод: | B247 6430 |
| Деталь: | Decal - Grip |
| Парткод: | A029 2984 |
| Деталь: | Lever:Release:Vertical Transport |
| Парткод: | B247 6426 |
| Деталь: | Release Button - Vertical Transport |
| Парткод: | B065 6428 |
| Деталь: | Release Lever - Vertical Transport |
| Парткод: | B065 6427 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3560 |
| Деталь: | Front Side Plate - Vertical Transpo |
| Парткод: | B065 6403 |
| Деталь: | Transport Unit:Vertical Transport:Assy |
| Парткод: | B247 6421 |
| Деталь: | Rear Side Plate - Vertical Transpor |
| Парткод: | B065 6404 |
| Деталь: | Vertical Driven Roller |
| Парткод: | AF02 0295 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0241 |
| Деталь: | Spring - 10mm |
| Парткод: | AA06 3487 |
| Деталь: | Transport Pressure Plate |
| Парткод: | B065 6407 |
| Деталь: | Stepped Screw - M5 |
| Парткод: | B247 6982 |
| Деталь: | Transport Pressure Plate |
| Парткод: | B065 6402 |
| Деталь: | Micro Switch Sheet |
| Парткод: | A096 5528 |
| Деталь: | Micro Switchbracket |
| Парткод: | B065 6122 |
| Деталь: | SPRING |
| Парткод: | A423 4433 |
| Деталь: | Shoulder Screw - M2.5 |
| Парткод: | AA14 3809 |
| Деталь: | LCT Stay |
| Парткод: | B065 6078 |
| Деталь: | Pulley - 26Z |
| Парткод: | AB03 2717 |
| Деталь: | Spacer - M8 |
| Парткод: | AA132142 |
| Деталь: | Scanner Shoe Pin |
| Парткод: | B132 1820 |
| Деталь: | 2nd Mirror Plate |
| Парткод: | A293 1766 |
| Деталь: | Shoe - Scanner |
| Парткод: | A069 1883 |
| Деталь: | Second Mirror |
| Парткод: | B065 1766 |
| Деталь: | Adjusting Pin:Carriage:No.2:Peen |
| Парткод: | B247 1753 |
| Деталь: | Carriage:No.2:Assy |
| Парткод: | B247 1751 |
| Деталь: | EXPOSURE LAMP |
| Парткод: | AX50 0081 |
| Деталь: | Rear Holder - Lamp |
| Парткод: | A294 1712 |
| Деталь: | REFLECTOR |
| Парткод: | B065 1735 |
| Деталь: | Invertor Cover |
| Парткод: | B065 1736 |
| Деталь: | Harness Guide |
| Парткод: | B065 1741 |
| Деталь: | 1st Scanner Front Side Plate |
| Парткод: | B065 1733 |
| Деталь: | STAY |
| Парткод: | B065 1737 |
| Деталь: | Harness Plate |
| Парткод: | B065 1740 |
| Деталь: | 1st Scanner Rear Side Plate |
| Парткод: | B065 1734 |
| Деталь: | 1st Mirror |
| Парткод: | B065 1743 |
| Деталь: | Carriage:No.1:Assy |
| Парткод: | B247 1732 |
| Деталь: | Spring Plate |
| Парткод: | B065 1738 |
| Деталь: | Harness - Scanner No.1 |
| Парткод: | B140 5610 |
| Деталь: | Base:Connecting |
| Парткод: | B247 1748 |
| Деталь: | Invertor:Xenon Lamp |
| Парткод: | B247 1747 |
| Деталь: | INSULATOR |
| Парткод: | B065 1742 |
| Деталь: | Base:Carriage:No.2:Peen |
| Парткод: | B247 1752 |
| Деталь: | Entrance Scanning Guide |
| Парткод: | B477 2581 |
| Деталь: | Guide Bracket |
| Парткод: | B477 2145 |
| Деталь: | SPRING |
| Парткод: | B477 4115 |
| Деталь: | Driven Entrance Scanning Roller |
| Парткод: | B477 2577 |
| Деталь: | Bushing- 4x8x4.5mm |
| Парткод: | 53 241 658 |
| Деталь: | SPACER |
| Парткод: | A374 2181 |
| Деталь: | Entrance Scanning Roller Shaft |
| Парткод: | B477 2575 |
| Деталь: | Arm:Roller:Scanning:Entrance |
| Парткод: | B477 2574 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | Entrance Scanning Base |
| Парткод: | B477 2561 |
| Деталь: | Bushing - 16x18x5 |
| Парткод: | AA08 2141 |
| Деталь: | Bracket:Link:Cover:Paper Feed:Peen |
| Парткод: | B652 1817 |
| Деталь: | Screw:Safety |
| Парткод: | AA14 3791 |
| Деталь: | Pull Out Roller |
| Парткод: | B477 2111 |
| Деталь: | Roller:Scanning:Entrance:Drive |
| Парткод: | B652 2411 |
| Деталь: | Drive Relay Roller |
| Парткод: | B477 2121 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Registration Sensor Bracket |
| Парткод: | B477 2665 |
| Деталь: | Discharge Brush |
| Парткод: | B477 2474 |
| Деталь: | Guide Plate:Scanning:Entrance |
| Парткод: | B652 2471 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Discharge Brush:Separation:Lower |
| Парткод: | B477 2146 |
| Деталь: | Lower paper feed guide |
| Парткод: | B477 2141 |
| Деталь: | Separation Cap |
| Парткод: | B477 2151 |
| Деталь: | LOWER GROUNDING PLATE |
| Парткод: | B477 2161 |
| Деталь: | Registration Sensor Relay Harness |
| Парткод: | B477 5681 |
| Деталь: | Link:Stopper:Cover:Paper Feed |
| Парткод: | B652 1816 |
| Деталь: | Tapping Screw:M3x6 |
| Парткод: | AA14 3846 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0037 |
| Деталь: | Spring - Registration Roller |
| Парткод: | 54 422 754 |
| Деталь: | Ball Bearing - 8x12x5 |
| Парткод: | A247 2800 |
| Деталь: | Spacer - 1x8x12 |
| Парткод: | AA13 2025 |
| Деталь: | Registration Roller - Lower |
| Парткод: | B247 2627 |
| Деталь: | Registration Roller:Upper:Press Fit |
| Парткод: | B247 2623 |
| Деталь: | Lower Registration Guide |
| Парткод: | B247 2611 |
| Деталь: | Stay:Reverse:Assy |
| Парткод: | B247 2700 |
| Деталь: | Friction Pad - B |
| Парткод: | B247 2702 |
| Деталь: | Snap Ring |
| Парткод: | G011 1058 |
| Деталь: | Drive Reverse Gear - 24z |
| Парткод: | AB01 1392 |
| Деталь: | Shaft:Reverse:Drive:Assy |
| Парткод: | G126 2713 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Paper Feed Roller:Separate |
| Парткод: | AF03 2080 |
| Деталь: | Torque Limiter - 53mnxm |
| Парткод: | A294 6700 |
| Деталь: | Shaft:Reverse Roller:Assy |
| Парткод: | G126 2714 |
| Деталь: | Stay:Reverse Roller:Peen |
| Парткод: | B247 2699 |
| Деталь: | Gear:Reverse |
| Парткод: | AB01 1591 |
| Деталь: | Registration Roller Gear |
| Парткод: | AB01 4077 |
| Деталь: | Timing Belt - S2MT140 |
| Парткод: | AA04 3944 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Middle Sensor Bracket |
| Парткод: | B065 2708 |
| Деталь: | Paper End Sensor Bracket |
| Парткод: | B065 2707 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | SPRING |
| Парткод: | AA06 0911 |
| Деталь: | Reverse Pressure Lever |
| Парткод: | B065 2709 |
| Деталь: | Bracket:Stepper Motor:MM42 |
| Парткод: | D054 2752 |
| Деталь: | Stepper Motor:Paper Feed Unit:Assy |
| Парткод: | B132 6655 |
| Деталь: | Gear - 24Z/46Z |
| Парткод: | AB01 7606 |
| Деталь: | Feed Lever |
| Парткод: | B065 6445 |
| Деталь: | Heat Sink:Stepper Motor:Connecting |
| Парткод: | D054 2759 |
| Деталь: | Cushion:Stepper Motor:Connecting |
| Парткод: | AA16 1168 |
| Деталь: | Paper Feed Motor - DC 7.4W |
| Парткод: | B477 3711 |
| Деталь: | Paper Feed Motor Stay |
| Парткод: | B477 3115 |
| Деталь: | Paper Feed Motor Bracket |
| Парткод: | B477 3111 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0842 |
| Деталь: | Gear - 50Z |
| Парткод: | B477 3163 |
| Деталь: | Gear - 37Z |
| Парткод: | B477 3161 |
| Деталь: | Gear - 31Z |
| Парткод: | B477 3151 |
| Деталь: | PULLEY |
| Парткод: | A548 2139 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Shaft:Separation:Drive |
| Парткод: | B477 3124 |
| Деталь: | Gear - 24Z |
| Парткод: | B477 3123 |
| Деталь: | Stopper:Shaft:Separation |
| Парткод: | B477 2244 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A859 2230 |
| Деталь: | Timing Belt:B40S2M178 |
| Парткод: | B6521773 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Timing Belt:B60S2M212 |
| Парткод: | B652 1613 |
| Деталь: | PULLEY |
| Парткод: | B477 3145 |
| Деталь: | Paper Feed Drive Bracket |
| Парткод: | B477 3181 |
| Деталь: | Feeler - Pick-up Roller Cam |
| Парткод: | A680 2262 |
| Деталь: | Pick-up Roller Cam |
| Парткод: | B477 3251 |
| Деталь: | Gear - 23Z |
| Парткод: | B477 3141 |
| Деталь: | Timing Belt:B40S3M186 |
| Парткод: | B652 1643 |
| Деталь: | Gear - 20Z |
| Парткод: | B477 3143 |
| Деталь: | Stepper Motor:MM42:0.95A:9.5V |
| Парткод: | AX04 0139 |
| Деталь: | PULLEY |
| Парткод: | B477 3177 |
| Деталь: | PULLEY |
| Парткод: | B477 3173 |
| Деталь: | Timing Belt:B40S2M170 |
| Парткод: | B652 1674 |
| Деталь: | Timing Belt:B40S3M180 |
| Парткод: | B652 1673 |
| Деталь: | PULLEY |
| Парткод: | B477 3171 |
| Деталь: | Pulley - 39Z |
| Парткод: | B301 2141 |
| Деталь: | Stepper Motor:Reverse:Assy |
| Парткод: | B132 4780 |
| Деталь: | Bracket:Motor:Reverse:Assy |
| Парткод: | B247 4810 |
| Деталь: | GEAR |
| Парткод: | AB01 7616 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3291 |
| Деталь: | DC Solenoid 24V |
| Парткод: | B247 4745 |
| Деталь: | Stepper Motor:DC5.12V 3.1W |
| Парткод: | B247 4785 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3811 |
| Деталь: | Transport Motor Bracket |
| Парткод: | B065 4789 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3292 |
| Деталь: | Jogger Motor Bracket |
| Парткод: | B065 4696 |
| Деталь: | Stepper Motor:Jogger:Assy |
| Парткод: | B132 4650 |
| Деталь: | MAGNETIC |
| Парткод: | AA02 1034 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA143183 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Roller Lever |
| Парткод: | A294 4754 |
| Деталь: | SPRING |
| Парткод: | AA060806 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Left Duplex Table |
| Парткод: | B065 4720 |
| Деталь: | Front Jogger Fence |
| Парткод: | B065 4681 |
| Деталь: | Spring Plate - Rear Jogger Fence |
| Парткод: | B065 4683 |
| Деталь: | Rear Jogger Fence |
| Парткод: | B065 4682 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA08 0034 |
| Деталь: | SPRING |
| Парткод: | AA06 3655 |
| Деталь: | Roller:Reversal:Driven |
| Парткод: | B247 4594 |
| Деталь: | Bracket:Reversal:Driven:Assy |
| Парткод: | B247 4655 |
| Деталь: | Drum Shaft Knob |
| Парткод: | B247 2410 |
| Деталь: | Development Drum Stay |
| Парткод: | B065 3258 |
| Деталь: | CHARGE CORONA UNIT |
| Парткод: | B247 2010 |
| Деталь: | Cleaner Motor Cover |
| Парткод: | B070 2365 |
| Деталь: | Front bushing |
| Парткод: | AA08 0147 |
| Деталь: | GROUNDING PLATE |
| Парткод: | A176 2054 |
| Деталь: | Corona Wire Cleaner |
| Парткод: | A096 2063 |
| Деталь: | Wire Cleaner Slider |
| Парткод: | A096 2062 |
| Деталь: | Slider Ring |
| Парткод: | A096 2065 |
| Деталь: | Screw Shaft |
| Парткод: | A176 2061 |
| Деталь: | Cushion - Spacer |
| Парткод: | B247 2295 |
| Деталь: | Bushing:Screw Shaft:Rear |
| Парткод: | B140 2291 |
| Деталь: | Grid:Charge Corona:N |
| Парткод: | A096 2060 |
| Деталь: | Charge Terminal Spring |
| Парткод: | AA06 3248 |
| Деталь: | Grid Terminal Spring |
| Парткод: | AA06 3249 |
| Деталь: | Rear End Block |
| Парткод: | AD02 2285 |
| Деталь: | Cover - Rear End Block |
| Парткод: | AD02 2307 |
| Деталь: | Rear Grid Anchor |
| Парткод: | A096 2051 |
| Деталь: | Charge Corona Wire |
| Парткод: | B070 2364 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 2284 |
| Деталь: | Front End Block |
| Парткод: | AD02 2283 |
| Деталь: | Cushion - Wire |
| Парткод: | B234 2123 |
| Деталь: | DC Motor:Cleaner:0.5W |
| Парткод: | AX04 0147 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 0087 |
| Деталь: | Cover - Front End Block |
| Парткод: | AD02 2306 |
| Деталь: | TERMINAL PLATE |
| Парткод: | A134 2363 |
| Деталь: | Front Grid Anchor |
| Парткод: | A096 2052 |
| Деталь: | Case:Charge Corona |
| Парткод: | B140 2292 |
| Деталь: | Fusing Exit Roller - Upper |
| Парткод: | AF04 0561 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | B140 4131 |
| Деталь: | Fusing Entrance Guide Plate Assy |
| Парткод: | B140 4135 |
| Деталь: | Lower Fusing Cover |
| Парткод: | B140 4203 |
| Деталь: | Upper Fusing Exit Guide Plate |
| Парткод: | B140 4234 |
| Деталь: | Grip:Fusing Unit:Front:Assy |
| Парткод: | B140 4174 |
| Деталь: | Side Plate Cover |
| Парткод: | B065 4138 |
| Деталь: | Upper Fusing Cover Assy |
| Парткод: | B140 4117 |
| Деталь: | Stripper Pawls |
| Парткод: | AE04 4060 |
| Деталь: | Bracket:Cover:Connector:Assy |
| Парткод: | B140 4113 |
| Деталь: | Development Cover Screw |
| Парткод: | AA14 3810 |
| Деталь: | SLIDER COVER |
| Парткод: | B065 4398 |
| Деталь: | Stripper Pawl Spring |
| Парткод: | AA06 0539 |
| Деталь: | Slider Spring |
| Парткод: | AA06 0916 |
| Деталь: | Screw:Slider |
| Парткод: | B247 4247 |
| Деталь: | Release Slider |
| Парткод: | B065 4397 |
| Деталь: | Front Lock Pawl |
| Парткод: | B065 4188 |
| Деталь: | Stripper Pawls Grip |
| Парткод: | B065 4184 |
| Деталь: | BUSHING |
| Парткод: | AA08 0274 |
| Деталь: | Stripper Pawls:Open And Close:Assy |
| Парткод: | B247 4080 |
| Деталь: | SPRING |
| Парткод: | AA06 6352 |
| Деталь: | Rear Lock Pawl |
| Парткод: | B065 4189 |
| Деталь: | Shaft:Release:Stripper Pawls |
| Парткод: | B247 4083 |
| Деталь: | Fusing Exit Roller Holder |
| Парткод: | B140 4141 |
| Деталь: | Cable - LVDS LDB |
| Парткод: | B247 5403 |
| Деталь: | Harness:75CPM |
| Парткод: | B065 5489 |
| Деталь: | Harness:60 |
| Парткод: | B140 5491 |
| Деталь: | Imaging Unit |
| Парткод: | D054 1852 |
| Деталь: | Harness - Laser Diode Unit |
| Парткод: | B247 5477 |
| Деталь: | Harness - Laser Diode Control |
| Парткод: | B247 5437 |
| Деталь: | Laser Diode Unit |
| Парткод: | B247 1859 |
| Деталь: | Shield Glass Rail |
| Парткод: | B065 1940 |
| Деталь: | Lens Holder - L0 |
| Парткод: | B065 1912 |
| Деталь: | Lens - L0 |
| Парткод: | AC02 4007 |
| Деталь: | 1st Mirror |
| Парткод: | AC03 0147 |
| Деталь: | 1st Mirror Holder |
| Парткод: | B065 1915 |
| Деталь: | Relay Polygon Motor Harness |
| Парткод: | B065 5453 |
| Деталь: | Polygon Mirror Motor:DC24V 24W |
| Парткод: | AX06 0324 |
| Деталь: | Seal - Lens L1 |
| Парткод: | B065 1955 |
| Деталь: | Shield Glass |
| Парткод: | AC01 5037 |
| Деталь: | Supporting Plate |
| Парткод: | G570 2827 |
| Деталь: | Lens Holder - L2 Right |
| Парткод: | B065 1925 |
| Деталь: | Lens Holder - L2 Left |
| Парткод: | B065 1926 |
| Деталь: | DTL |
| Парткод: | GC02 5010 |
| Деталь: | 2nd Mirror Holder |
| Парткод: | B065 1930 |
| Деталь: | Middle Mirror Holder |
| Парткод: | B065 1932 |
| Деталь: | 2nd Mirror |
| Парткод: | AC03 0148 |
| Деталь: | PCB:Sync Detector |
| Парткод: | D054 5320 |
| Деталь: | Seal - Shield Glass Holder |
| Парткод: | B065 1946 |
| Деталь: | Shield Glass Holder |
| Парткод: | B065 1944 |
| Деталь: | Seal - Shield Glass |
| Парткод: | B065 1945 |
| Деталь: | Sheet - Shielding Plate |
| Парткод: | B065 1958 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF03 0081 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Paper Feed Roller:Feed |
| Парткод: | AF03 1082 |
| Деталь: | Pick-up Gear Cover |
| Парткод: | B065 6350 |
| Деталь: | Idler Gear |
| Парткод: | AB01 1465 |
| Деталь: | Pick-up Arm |
| Парткод: | B065 6357 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | SPRING |
| Парткод: | AA06 0898 |
| Деталь: | Feed Roller Shaft |
| Парткод: | AA14 0828 |
| Деталь: | Feed Lever |
| Парткод: | B065 6445 |
| Деталь: | SPRING |
| Парткод: | AA06 0899 |
| Деталь: | Paper Feed Sensor Bracket |
| Парткод: | B065 6358 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Feed Stay |
| Парткод: | B065 6364 |
| Деталь: | Paper Feed Unit Stay |
| Парткод: | B065 6375 |
| Деталь: | Gear - 21Z/38Z |
| Парткод: | AB01 7617 |
| Деталь: | DC Solenoid:Pickup:Assy |
| Парткод: | B132 6659 |
| Деталь: | SPRING |
| Парткод: | AA06 0897 |
| Деталь: | Harness - Paper Feed Unit Upper |
| Парткод: | B132 7581 |
| Деталь: | Harness - Paper Feed Unit Lower |
| Парткод: | B132 7580 |
| Деталь: | Paper End Sensor Bracket |
| Парткод: | B065 6345 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Paper Feed Guide Plate |
| Парткод: | B140 6339 |
| Деталь: | Transport Roller:Drive:Grip |
| Парткод: | AF02 0726 |
| Деталь: | Gear - 35Z |
| Парткод: | AB01 1466 |
| Деталь: | Feed Gear Cover |
| Парткод: | B065 6353 |
| Деталь: | Drive bracket |
| Парткод: | B065 6366 |
| Деталь: | Arm Screw |
| Парткод: | 58 942 540 |
| Деталь: | Driven Pressure Lever |
| Парткод: | B065 6457 |
| Деталь: | SPRING |
| Парткод: | AA06 0896 |
| Деталь: | Heat Sink Base |
| Парткод: | B065 6334 |
| Деталь: | HEAT SINK |
| Парткод: | B065 6337 |
| Деталь: | Heat Sink Sheet |
| Парткод: | B065 6338 |
| Деталь: | Heat Sink Spring |
| Парткод: | AA06 3889 |
| Деталь: | Paper Feed Unit:Paper Bank |
| Парткод: | B132 6621 |
| Деталь: | Ground Plate:Reverse:Paper Feed Unit |
| Парткод: | B140 6377 |
| Деталь: | INSULATOR |
| Парткод: | B065 4255 |
| Деталь: | Decal - Misfeed Removal |
| Парткод: | B065 4274 |
| Деталь: | Decal - Exit |
| Парткод: | B065 4481 |
| Деталь: | Inner cover |
| Парткод: | B246 4266 |
| Деталь: | Decal - Fusing Knob |
| Парткод: | B065 4167 |
| Деталь: | Knob:Fusing |
| Парткод: | AG05 0098 |
| Деталь: | Cleaning Unit:Hot Roller:Assy |
| Парткод: | B247 4097 |
| Деталь: | Web Shaft |
| Парткод: | B065 4207 |
| Деталь: | Front Oil Supply Bushing |
| Парткод: | B140 4191 |
| Деталь: | SPRING |
| Парткод: | AA06 3886 |
| Деталь: | Bracket:Stopper:Assy |
| Парткод: | B140 4209 |
| Деталь: | Pressure Roller Gear |
| Парткод: | B065 4211 |
| Деталь: | Cleaning Unit Cover |
| Парткод: | B140 4193 |
| Деталь: | Pressure Roller:Cleaning Felt |
| Парткод: | AE04 4068 |
| Деталь: | Cleaning Unit Drive Positioning Plate |
| Парткод: | B140 4187 |
| Деталь: | Cleaning Felt Roller Assy |
| Парткод: | B140 4181 |
| Деталь: | Shaft:Drive:Rolling:Assy |
| Парткод: | B247 4242 |
| Деталь: | Shaft:Drive:Oil Supply Roller:Assy |
| Парткод: | B247 4239 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AE03 1036 |
| Деталь: | Gear - 37Z |
| Парткод: | B065 4222 |
| Деталь: | GEAR |
| Парткод: | B065 4241 |
| Деталь: | Brake pad |
| Парткод: | B065 4247 |
| Деталь: | Feeler Guard Bracket |
| Парткод: | B065 4232 |
| Деталь: | Brake Spring Plate |
| Парткод: | B140 4190 |
| Деталь: | Bracket:Drive:Assy |
| Парткод: | B247 4188 |
| Деталь: | Web Cover |
| Парткод: | B065 4231 |
| Деталь: | DC Motor: DC5V 0.46W |
| Парткод: | AX04 0159 |
| Деталь: | Motor Plate Bracket |
| Парткод: | B065 4225 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Motor Gear |
| Парткод: | B065 4223 |
| Деталь: | Gear:Z23:Oil Supply Roller |
| Парткод: | B247 4244 |
| Деталь: | Gear - 50Z |
| Парткод: | B065 4238 |
| Деталь: | Gear:Idler:Cleaning Unit |
| Парткод: | B247 4235 |
| Деталь: | Web Harness |
| Парткод: | B065 4248 |
| Деталь: | Gear:Stopper:Oil Supply Roller |
| Парткод: | B247 4234 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3851 |
| Деталь: | FEELER SPRING |
| Парткод: | B065 4221 |
| Деталь: | Feeler:Oil End Sensor |
| Парткод: | B140 4195 |
| Деталь: | Inner Back:Oil Supply Bushing |
| Парткод: | B140 4192 |
| Деталь: | Bottle:Drive:Unit |
| Парткод: | B247 3306 |
| Деталь: | Toner Bottle Drive Bracket |
| Парткод: | B065 3309 |
| Деталь: | SPRING |
| Парткод: | AA06 0291 |
| Деталь: | DC Motor:Toner Bottle:DC24V 5.85W |
| Парткод: | B247 5312 |
| Деталь: | Shaft:Idler:Drive:Toner Bottle |
| Парткод: | B247 3332 |
| Деталь: | Bracket:Turn:Toner Bottle:Sub-assy |
| Парткод: | B247 3311 |
| Деталь: | Outer Shutter Shield |
| Парткод: | A229 3263 |
| Деталь: | Outer Shutter |
| Парткод: | A229 3261 |
| Деталь: | Inner Shutter |
| Парткод: | A229 3262 |
| Деталь: | Upper Shutter Shield |
| Парткод: | A229 3266 |
| Деталь: | Shutter Lever |
| Парткод: | A229 3264 |
| Деталь: | Shutter Cover |
| Парткод: | A229 3285 |
| Деталь: | Rubber Bushing - Toner Supply Unit |
| Парткод: | A229 3219 |
| Деталь: | Decal - Toner Supply |
| Парткод: | AA00 1394 |
| Деталь: | Bottle Roller |
| Парткод: | A096 3224 |
| Деталь: | Gear:Toner Bottle:Assy |
| Парткод: | B065 3306 |
| Деталь: | Shield Plate - Toner Bottle |
| Парткод: | A293 3234 |
| Деталь: | Toner Bottle Chuck |
| Парткод: | A293 3230 |
| Деталь: | Toner Slider |
| Парткод: | A293 3227 |
| Деталь: | Flat Screw:Chuck:Bottle |
| Парткод: | AA14 3816 |
| Деталь: | SCREW |
| Парткод: | B247 3331 |
| Деталь: | Chuck Roller |
| Парткод: | A229 3232 |
| Деталь: | Shaft:Chuck |
| Парткод: | B247 3345 |
| Деталь: | Chuck Spring |
| Парткод: | AA06 3366 |
| Деталь: | Toner Bottle Stopper |
| Парткод: | A293 3220 |
| Деталь: | Toner Bottle Pawl |
| Парткод: | A293 3282 |
| Деталь: | SPRING |
| Парткод: | B247 3330 |
| Деталь: | Contact Point Stay - Upper |
| Парткод: | B247 3273 |
| Деталь: | Bracket:Hinge:Open And Close:Assy |
| Парткод: | B247 3316 |
| Деталь: | External Circlip - Mm8 |
| Парткод: | A222 2724 |
| Деталь: | Contact Point Stay - Lower |
| Парткод: | B247 3271 |
| Деталь: | Toner Catchpan Bottle |
| Парткод: | B247 3258 |
| Деталь: | Spacer - M6 |
| Парткод: | AA13 2024 |
| Деталь: | Motor Joint Gear |
| Парткод: | A229 3243 |
| Деталь: | Toner Bottle Joint Gear |
| Парткод: | A229 3242 |
| Деталь: | Jogger H.P. Sensor Bracket |
| Парткод: | B065 4699 |
| Деталь: | Relay Paper Feed Harness |
| Парткод: | B065 2762 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Duplex Gate Pawl |
| Парткод: | B065 4733 |
| Деталь: | Gate Pawl Cushion |
| Парткод: | B065 4738 |
| Деталь: | Lower Duplex Bracket |
| Парткод: | B065 4860 |
| Деталь: | SPACER |
| Парткод: | B065 4865 |
| Деталь: | Belt Holder Fixing Plate |
| Парткод: | A294 4723 |
| Деталь: | Timing Belt - 40S2M810G |
| Парткод: | AA04 3294 |
| Деталь: | Front Jogger Fence Slider |
| Парткод: | B065 4692 |
| Деталь: | Rear Jogger Fence Slider |
| Парткод: | B065 4693 |
| Деталь: | Duplex Guide |
| Парткод: | A096 4595 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0148 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0149 |
| Деталь: | Exit Reverse Sensor Bracket |
| Парткод: | B065 4715 |
| Деталь: | CUSHION |
| Парткод: | A294 4669 |
| Деталь: | Gear - 30Z/45Z |
| Парткод: | AB01 7615 |
| Деталь: | Upper Transport Guide Plate Assy |
| Парткод: | B140 4710 |
| Деталь: | SPRING |
| Парткод: | AA06 2318 |
| Деталь: | Jogger Pulley |
| Парткод: | AB03 0732 |
| Деталь: | Drawer Bracket - 12P |
| Парткод: | B065 4791 |
| Деталь: | Duplex Harness - 12P |
| Парткод: | B065 4981 |
| Деталь: | Drawer Bracket - 32P |
| Парткод: | B065 4790 |
| Деталь: | Harness:Duplex Unit:32Pin |
| Парткод: | B247 4980 |
| Деталь: | Support Bracket |
| Парткод: | B065 4619 |
| Деталь: | SPRING |
| Парткод: | AA06 2319 |
| Деталь: | DC Solenoid 24V |
| Парткод: | B247 4740 |
| Деталь: | Bracket:Jogger:Assy |
| Парткод: | B247 4820 |
| Деталь: | Relay Registration Harness |
| Парткод: | B065 2763 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Sensor bracket |
| Парткод: | B065 2621 |
| Деталь: | Paper Dust Removal Case |
| Парткод: | B065 2620 |
| Деталь: | Case Seal |
| Парткод: | AA15 2441 |
| Деталь: | Development Connector Bracket |
| Парткод: | B065 2608 |
| Деталь: | Upper Front Registration Guide |
| Парткод: | B140 2614 |
| Деталь: | Lower Front Registration Guide |
| Парткод: | B140 2622 |
| Деталь: | Paper Feed Stay |
| Парткод: | B065 2682 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Paper Feed Roller:Feed:Manual Feed |
| Парткод: | AF031083 |
| Деталь: | Gear - 18Z |
| Парткод: | AB01 1478 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2116 |
| Деталь: | SPRING |
| Парткод: | AA06 0888 |
| Деталь: | Pick-up Roller Arm |
| Парткод: | B065 2688 |
| Деталь: | Gear - 15T |
| Парткод: | 54 472 706 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF03 0080 |
| Деталь: | Feed Roller Shaft |
| Парткод: | AA14 0819 |
| Деталь: | SPRING |
| Парткод: | AA06 0887 |
| Деталь: | DC Solenoid 24V |
| Парткод: | B247 2690 |
| Деталь: | BUSHING |
| Парткод: | AA08 3019 |
| Деталь: | Magnetic Clutch:0.53N M:36Z |
| Парткод: | AX20 0277 |
| Деталь: | Case Cap |
| Парткод: | B065 3568 |
| Деталь: | Toner Correction Agitator |
| Парткод: | B065 3573 |
| Деталь: | Toner Collection Case |
| Парткод: | B065 3565 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Toner Receiving Spring |
| Парткод: | B065 3566 |
| Деталь: | Toner Catchpan |
| Парткод: | B065 3557 |
| Деталь: | Shaft:Discharge Used Toner:Long:Assy |
| Парткод: | B247 3609 |
| Деталь: | Toner Collection Idle Gear |
| Парткод: | B065 3588 |
| Деталь: | Shaft:Idler:Discharge Used Toner |
| Парткод: | B247 3590 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Screw Gear |
| Парткод: | B065 3585 |
| Деталь: | Spacer - M6 |
| Парткод: | AA13 2208 |
| Деталь: | SPRING |
| Парткод: | B065 3561 |
| Деталь: | Toner Collection Gear |
| Парткод: | B065 3587 |
| Деталь: | BUSHING |
| Парткод: | B065 3581 |
| Деталь: | Transport Screw:Discharge Used Toner:Assy |
| Парткод: | B247 3570 |
| Деталь: | SPRING GUIDE |
| Парткод: | B065 3583 |
| Деталь: | Screw Gear |
| Парткод: | B065 3586 |
| Деталь: | Brushless MotorDC24V 2.4W |
| Парткод: | AX06 0302 |
| Деталь: | BUSHING - M4 |
| Парткод: | H053 2208 |
| Деталь: | Base:Discharge Used Toner:Assy |
| Парткод: | B247 3559 |
| Деталь: | Toner Collection Discharge Harness |
| Парткод: | B065 3593 |
| Деталь: | Seal - 40x68 |
| Парткод: | B065 3637 |
| Деталь: | Gear - 22Z |
| Парткод: | B065 3645 |
| Деталь: | Toner Collection Cap |
| Парткод: | B065 3654 |
| Деталь: | Toner Collection Pipe |
| Парткод: | B065 3601 |
| Деталь: | PULLEY |
| Парткод: | B065 3660 |
| Деталь: | Shielding Plate: |
| Парткод: | B247 3652 |
| Деталь: | Toner Collection Case - Transport |
| Парткод: | B065 3649 |
| Деталь: | Toner Collection Joint |
| Парткод: | B065 3650 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Relay Paper Feed Harness |
| Парткод: | B065 2762 |
| Деталь: | Transport Screw:Discharge Used Toner: |
| Парткод: | B247 3641 |
| Деталь: | Ratch |
| Парткод: | A096 3712 |
| Деталь: | Toner Collection Shaft |
| Парткод: | B065 3610 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Transport Screw:Used Toner:Unit |
| Парткод: | B247 3670 |
| Деталь: | Shaft:Discharge Used Toner: |
| Парткод: | B247 3604 |
| Деталь: | Toner Separation Case |
| Парткод: | B065 3629 |
| Деталь: | Toner Collection Seal |
| Парткод: | B065 3636 |
| Деталь: | Transfer Belt Cleaning Blade |
| Парткод: | AD04 1126 |
| Деталь: | Spring Plate |
| Парткод: | B065 3962 |
| Деталь: | LEVER SHAFT |
| Парткод: | B247 3965 |
| Деталь: | LEVER |
| Парткод: | B065 3963 |
| Деталь: | BUSHING |
| Парткод: | B065 3964 |
| Деталь: | Shaft - On-off |
| Парткод: | B247 3961 |
| Деталь: | SPRING |
| Парткод: | AA06 3877 |
| Деталь: | Cleaning Roller |
| Парткод: | B247 3925 |
| Деталь: | Spacer - M6 |
| Парткод: | AA13 2024 |
| Деталь: | Toner Collection Coil |
| Парткод: | B247 3911 |
| Деталь: | Exit Seal |
| Парткод: | AD04 7025 |
| Деталь: | TAPE |
| Парткод: | A229 3934 |
| Деталь: | Agitator |
| Парткод: | B247 3914 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA082101 |
| Деталь: | Toner Collection Gear Coil |
| Парткод: | B065 3918 |
| Деталь: | Cleaning Roller Terminal |
| Парткод: | B065 3928 |
| Деталь: | Front bushing |
| Парткод: | A229 3910 |
| Деталь: | Electrode Plate Cover |
| Парткод: | B065 3922 |
| Деталь: | Idle Gear - 1 |
| Парткод: | B065 3920 |
| Деталь: | Idle Gear - 2 |
| Парткод: | B065 3921 |
| Деталь: | DC Solenoid 24V |
| Парткод: | B247 3966 |
| Деталь: | Bushing - 6x10x9mm |
| Парткод: | AA08 2058 |
| Деталь: | Rear bushing |
| Парткод: | A229 3911 |
| Деталь: | Cam Gear - 37z |
| Парткод: | AB01 4176 |
| Деталь: | Entrance Guide Plate |
| Парткод: | B065 3955 |
| Деталь: | Power Pack |
| Парткод: | AZ320164 |
| Деталь: | Harness - Transfer Unit |
| Парткод: | B247 3976 |
| Деталь: | Anti Static Brush |
| Парткод: | AA12 0067 |
| Деталь: | Guide Plate:Exit:Exit:Upper |
| Парткод: | B246 4311 |
| Деталь: | Exhaust Cover Assy |
| Парткод: | B140 4313 |
| Деталь: | Front Exhaust Side Plate |
| Парткод: | B065 4306 |
| Деталь: | Slide Rail:Fusing/paper Exit Unit:Left:Assy |
| Парткод: | B247 4440 |
| Деталь: | Left Rise Guide Plate |
| Парткод: | B140 4312 |
| Деталь: | Bracket:Shaft:Lock:Assy |
| Парткод: | B247 4263 |
| Деталь: | Magnet Catch Bracket |
| Парткод: | B0651197 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 1012 |
| Деталь: | Rail:Left:Machine Or Copier:Assy |
| Парткод: | B247 4835 |
| Деталь: | Guide Roller - B |
| Парткод: | A300 2134 |
| Деталь: | Roller - Positioning Guide |
| Парткод: | 67 542 866 |
| Деталь: | BRACKET |
| Парткод: | B065 1092 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Stripper Pawls Plate |
| Парткод: | B065 4179 |
| Деталь: | Rear Exhaust Side Plate |
| Парткод: | B065 4307 |
| Деталь: | Right Duplex Rail |
| Парткод: | B247 4591 |
| Деталь: | Duplex Fan Harness |
| Парткод: | B065 1198 |
| Деталь: | Fan Motor DC24V/1.92W |
| Парткод: | AX64 0183 |
| Деталь: | Bracket:Fan:Duplex |
| Парткод: | B065 1200 |
| Деталь: | Holder Bracket |
| Парткод: | B065 4830 |
| Деталь: | Exit Detection Harness |
| Парткод: | B065 4499 |
| Деталь: | Cushion - Motor |
| Парткод: | AA16 1104 |
| Деталь: | Base cover |
| Парткод: | B0651075 |
| Деталь: | Transfer Unit Lever |
| Парткод: | B065 3832 |
| Деталь: | Bushing - 10mm |
| Парткод: | AA08 2064 |
| Деталь: | Front Transfer Stay |
| Парткод: | B065 1096 |
| Деталь: | Drum Stay:Development:Upper:Peen |
| Парткод: | B140 3253 |
| Деталь: | Development Unit Rail |
| Парткод: | B065 3251 |
| Деталь: | Development Grounding Plate |
| Парткод: | A0961679 |
| Деталь: | Total Counter:7FIG:24V:MI2 |
| Парткод: | AX31 0047 |
| Деталь: | Bracket:Total Counter |
| Парткод: | B247 5890 |
| Деталь: | Right Rail - Drum Unit |
| Парткод: | B065 3252 |
| Деталь: | Roller - Positioning Guide |
| Парткод: | 67 542 866 |
| Деталь: | Heater:120V |
| Парткод: | B246 3841 |
| Деталь: | Heater:240V |
| Парткод: | B246 3843 |
| Деталь: | Release Positioning Plate |
| Парткод: | B065 3831 |
| Деталь: | Positioning Plate:Transfer Unit:Assy |
| Парткод: | B247 3820 |
| Деталь: | Decal - Transfer Unit Lever |
| Парткод: | B065 3833 |
| Деталь: | Transfer Unit Stay |
| Парткод: | B065 3811 |
| Деталь: | Transfer Rely Harness |
| Парткод: | B065 3812 |
| Деталь: | Slide Rail - Right |
| Парткод: | AA07 0077 |
| Деталь: | Duct Clip |
| Парткод: | B065 1094 |
| Деталь: | Left Duct - PCU |
| Парткод: | B065 1091 |
| Деталь: | Heat Insulation |
| Парткод: | B065 1095 |
| Деталь: | Harness - PCU |
| Парткод: | B247 2496 |
| Деталь: | Left Rail |
| Парткод: | B065 1098 |
| Деталь: | Positioning Plate:Fusing Unit:Assy |
| Парткод: | B247 4168 |
| Деталь: | Channel:Lengthwise:Middle Front:Assy |
| Парткод: | B247 3815 |
| Деталь: | Handle Stay |
| Парткод: | B247 3827 |
| Деталь: | Hot Roller:Mm40 |
| Парткод: | AE01 1117 |
| Деталь: | Ball Bearing - 40x52x7 |
| Парткод: | AE03 0054 |
| Деталь: | Thermal Insulating Bushing |
| Парткод: | AE03 2026 |
| Деталь: | SPRING |
| Парткод: | AA06 0894 |
| Деталь: | Hot Roller External Circlip |
| Парткод: | B140 4172 |
| Деталь: | Gear - 40Z |
| Парткод: | B140 4194 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AE02 0162 |
| Деталь: | Ball Bearing - 8x19x6 |
| Парткод: | AE03 0053 |
| Деталь: | Thermostat- 211c |
| Парткод: | AW11 0066 |
| Деталь: | Heater:120V:550W |
| Парткод: | AX44 0213 |
| Деталь: | Heater:230v:550w |
| Парткод: | AX44 0216 |
| Деталь: | Electrode Plate:Thermostat:Coupling |
| Парткод: | B1104223 |
| Деталь: | Thermostat Electrode Plate |
| Парткод: | B140 4169 |
| Деталь: | Housing:Thermostat:EXP |
| Парткод: | B247 4128 |
| Деталь: | Rear Harness |
| Парткод: | B065 4151 |
| Деталь: | Harness - Front |
| Парткод: | B247 4149 |
| Деталь: | Bracket:Thermostat |
| Парткод: | B140 4145 |
| Деталь: | Plate:Thermistor |
| Парткод: | B140 4179 |
| Деталь: | Middle Thermistor Bracket |
| Парткод: | B140 4197 |
| Деталь: | Thermistor - Inner Back |
| Парткод: | AW10 0109 |
| Деталь: | Thermistor - Middle |
| Парткод: | AW10 0108 |
| Деталь: | Inner Back Thermistor Bracket |
| Парткод: | B140 4196 |
| Деталь: | Upper Stay |
| Парткод: | B247 4142 |
| Деталь: | Front Heater Holder |
| Парткод: | B140 4171 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | A4131670 |
| Деталь: | Rear Heater Holder |
| Парткод: | B140 4170 |
| Деталь: | Thermostat-192c |
| Парткод: | AW11 0064 |
| Деталь: | Heater:120V:650W |
| Парткод: | AX44 0214 |
| Деталь: | Heater:230v:650w |
| Парткод: | AX44 0217 |
| Деталь: | Drawer Bracket Assy |
| Парткод: | B140 4157 |
| Деталь: | Harness Plate |
| Парткод: | B140 4159 |
| Деталь: | Connector Cover Bracket |
| Парткод: | B140 4167 |
| Деталь: | Exit Plate |
| Парткод: | B065 4185 |
| Деталь: | Connector - 3P |
| Парткод: | A247 4249 |
| Деталь: | Harness:Fusing Unit:NA |
| Парткод: | B140 4162 |
| Деталь: | Harness:Fusing Unit:EU |
| Парткод: | B140 4164 |
| Деталь: | Inner cover |
| Парткод: | B247 4799 |
| Деталь: | Caution Decal - Duplex |
| Парткод: | B065 4797 |
| Деталь: | Release Grip |
| Парткод: | B247 4674 |
| Деталь: | Shaft:Lever:Release |
| Парткод: | B247 4673 |
| Деталь: | Duplex Lock Arm |
| Парткод: | B065 4671 |
| Деталь: | Duplex Release Bracket |
| Парткод: | B065 4675 |
| Деталь: | SPRING |
| Парткод: | AA06 2320 |
| Деталь: | Release Lever Bracket |
| Парткод: | B065 4672 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Upper Duplex Stay |
| Парткод: | B065 4987 |
| Деталь: | Exit Duplex Guide Plate |
| Парткод: | B140 4800 |
| Деталь: | SPRING |
| Парткод: | AA06 6353 |
| Деталь: | Spring Plate - Right Table Guide |
| Парткод: | B065 4728 |
| Деталь: | Right Guide Table |
| Парткод: | B065 4726 |
| Деталь: | DUPLEX UNIT |
| Парткод: | B247 4500 |
| Деталь: | Right Duplex Bracket |
| Парткод: | B065 4725 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3811 |
| Деталь: | Right Sensor Bracket |
| Парткод: | B065 4727 |
| Деталь: | Harness - Duplex |
| Парткод: | B247 4590 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0149 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 2077 |
| Деталь: | Spring Plate - Driven Roller |
| Парткод: | B065 4731 |
| Деталь: | Lower Transport Guide Plate |
| Парткод: | B065 4730 |
| Деталь: | Guide Plate Band |
| Парткод: | A096 4928 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3581 |
| Деталь: | Guide Plate Pressure Holder |
| Парткод: | A229 4727 |
| Деталь: | Guide Stopper Roller |
| Парткод: | AF02 2067 |
| Деталь: | Guide Plate Lever Hook |
| Парткод: | B065 4933 |
| Деталь: | Decal - Guide Plate Lever |
| Парткод: | B065 4867 |
| Деталь: | Guide Plate Lever |
| Парткод: | B065 4531 |
| Деталь: | Front Shaft - By-pass |
| Парткод: | B065 2743 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Paper End Feeler |
| Парткод: | B065 2729 |
| Деталь: | Guide Plate:Manual Feed:Peen |
| Парткод: | B247 2721 |
| Деталь: | Machine Or Copier Paper Feed Cover |
| Парткод: | B140 2660 |
| Деталь: | Magnet Catch Bracket |
| Парткод: | B140 2662 |
| Деталь: | Feed Guide Gear |
| Парткод: | A096 2780 |
| Деталь: | Manual Feed Table:Assy |
| Парткод: | B247 2730 |
| Деталь: | Decal - Paper Set |
| Парткод: | B065 2746 |
| Деталь: | Front Side Fence - By-pass |
| Парткод: | B065 2737 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0513 |
| Деталь: | Rear Side Fence - By-pass |
| Парткод: | B065 2735 |
| Деталь: | MANUAL FEED TABLE |
| Парткод: | B065 2732 |
| Деталь: | Support Stay:Manual Feed:Front:Assy |
| Парткод: | B247 2738 |
| Деталь: | Support Stay:Manual Feed:Rear:Assy |
| Парткод: | B247 2740 |
| Деталь: | Sensor bracket |
| Парткод: | B065 2741 |
| Деталь: | Gear:Manual Feed Table |
| Парткод: | B098 3492 |
| Деталь: | Paper size sensor |
| Парткод: | B247 2745 |
| Деталь: | By-pass Table Cover |
| Парткод: | B065 2733 |
| Деталь: | Sheet - Manual Feed Guide Plate |
| Парткод: | B065 2723 |
| Деталь: | Supporting Plate |
| Парткод: | B065 6777 |
| Деталь: | Lock Spring - Tandem Tray |
| Парткод: | AA06 0592 |
| Деталь: | Left Rail Bracket |
| Парткод: | B132 6742 |
| Деталь: | Base:Slide Rail:Tandem LCT:Peen |
| Парткод: | B247 6792 |
| Деталь: | Lock Arm - Tandem Tray |
| Парткод: | B065 6135 |
| Деталь: | Slide Rail - Left |
| Парткод: | B247 6254 |
| Деталь: | Upper Heat Sink |
| Парткод: | B065 6116 |
| Деталь: | Heater:115V:18W:Upper |
| Парткод: | AX40 0176 |
| Деталь: | Heater:240V:18W:Upper |
| Парткод: | AX40 0178 |
| Деталь: | Guide Plate - Upper Heat Sink |
| Парткод: | A248 6103 |
| Деталь: | Slide Rail:Tandem LCT |
| Парткод: | AA07 0072 |
| Деталь: | Slidebracket |
| Парткод: | B065 6774 |
| Деталь: | Guide Stay |
| Парткод: | B065 6264 |
| Деталь: | Slide Rail - Right |
| Парткод: | B247 6252 |
| Деталь: | Tandem Tray Stay |
| Парткод: | B065 6776 |
| Деталь: | LCT Cable Bracket |
| Парткод: | B065 5808 |
| Деталь: | Grid Receptacle Terminal |
| Парткод: | B065 2481 |
| Деталь: | Charge Receptacle Terminal |
| Парткод: | B065 2482 |
| Деталь: | Rear Receptacle |
| Парткод: | A294 2051 |
| Деталь: | Receptacle Pin |
| Парткод: | A294 2052 |
| Деталь: | Electrode Plate:Drum Shaft:Assy |
| Парткод: | B247 1154 |
| Деталь: | ELECTRODE PLATE |
| Парткод: | B065 3262 |
| Деталь: | BRACKET |
| Парткод: | B065 1137 |
| Деталь: | Drum Shaft:Assy |
| Парткод: | B247 1140 |
| Деталь: | Fly Wheel |
| Парткод: | A294 1119 |
| Деталь: | PARTITION PLATE |
| Парткод: | B065 1134 |
| Деталь: | Boss |
| Парткод: | B065 1145 |
| Деталь: | Gear -156Z |
| Парткод: | AB01 2315 |
| Деталь: | Gear - Z40 (D052/D053) |
| Парткод: | AB01 1482 |
| Деталь: | Gear:Z31 (D054) |
| Парткод: | AB01 1507 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3948 |
| Деталь: | Gear -38/Z59 (D052/D053) |
| Парткод: | AB01 7640 |
| Деталь: | Gear:Z38/Z67 (D054) |
| Парткод: | AB01 7760 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0792 |
| Деталь: | Bracket:Tightener:Assy |
| Парткод: | B247 1122 |
| Деталь: | Brushless Motor DC24V/25W |
| Парткод: | B247 1110 |
| Деталь: | Guide Plate:Positioning Pin:Duplex:Assy |
| Парткод: | B247 1084 |
| Деталь: | Pulley - 28Z |
| Парткод: | AB03 0458 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3945 |
| Деталь: | Ring - 55 |
| Парткод: | A2291135 |
| Деталь: | Pulley - 74Z |
| Парткод: | AB03 0724 |
| Деталь: | Transfer Drive Bracket |
| Парткод: | B065 1147 |
| Деталь: | Joint:Transfer Drive:Assy |
| Парткод: | B247 1149 |
| Деталь: | Spacer - 1x8x12 |
| Парткод: | AA13 2025 |
| Деталь: | SPRING |
| Парткод: | AA06 3654 |
| Деталь: | JOINT |
| Парткод: | B065 1131 |
| Деталь: | Screw:M5x10 |
| Парткод: | B247 1123 |
Коды ошибок
101
120
121
122
123
143
144
165
181
183
184
202
203
204
205
220
300
303
304
305
306
310
311
312
314
315
316
317
321
322
335
336
337
338
340
341
342
345
350
351
352
353
354
355
401
402
430
440
441
490
495
496
497
501
502
503
504
507
510
515
520
521
531
541
542
543
544
545
547
550
551
552
553
555
557
559
569
590
599
610
611
612
620
621
623
624
626
627
650
651
670
672
700
701
720
721
723
724
725
726
727
728
729
730
732
733
735
736
737
738
739
740
741
742
743
744
750
753
754
755
756
757
760
761
762
763
764
765
766
767
770
780
781
782
784
785
786
790
817
818
819
821
822
824
826
828
833
834
850
851
853
854
855
856
857
860
861
863
864
865
866
867
868
870
873
874
875
880
900
901
910 ... 914
919
920
921
925
953
954
955
964
984
985
986
990
991
992
994
997
998
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 122 |
| Display: | Service Call 122: Error |
| Description: | Finisher Decurler Failure, Code 122 The level of the Decurler Cam Home Sensor did not change 4 seconds after the Decurler Cam Clutch has turned on. |
| Causes: | • Decurler Cam Clutch • Stacker Motor • Finisher Control Board |
| Remedy: | 1 1. Rotate the actuator while running the Decurler Cam Position test in diagnostics. 2. Does the value change between H and L? Go to step 2. Troubleshoot using the transmissive sensor procedure. 2 Does the decurler cam clutch operate in diagnostics? Check for a mechanical problem with the decurler cam clutch drive. If no problem is found replace the clutch. Go to step 3. 3 Is +24 VDC present at P/J 849-1? Replace the decurler cam clutch. Go to step 4. 4 Is +24 VDC present at test point 5 on the finisher control board? Replace the finisher control board. Troubleshoot the +24 VDC interlock circuit. 5 Is +24 VDC present at P/J 847-11 with the Finisher Stacker Motor Down test running in diagnostics? Replace the stacker motor. Replace the finisher control board |
| Error code: | 123 |
| Display: | Service Call 123: Error |
| Description: | Finisher Set Clamp Failure, Code 123 The set clamp home sensor did not turn on within 2 seconds after the set clamp started operation. |
| Causes: | • Set Clamp Solenoid • Finisher Control Board |
| Remedy: | 1 1. Check the Set Clamp home sensor in diagnostics. 2. Does the value change from H to L while rotating the actuator? Go to step 2. Use the transmissive Sensor procedure to diagnose and repair the sensor. 2 Does the solenoid energize when running the Set Clamp Paddle test in diagnostics? Go to step 3. Go to step 4. 3 1. Run the Eject Forward Test and then the Eject Release Test in diagnostics. 2. Does the set clamp paddle turn once? Replace the finisher control board. Go to step 4. 4 Is +24 VDC present at P848A-10? Go to step 5. Go to step 6. 5 Is +24 VDC present at P848A-11? Replace the finisher control board. Replace the set clamp solenoid. 6 Is +24 VDC present at test point 9 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. |
| Error code: | 143 |
| Display: | Service Call 143:Error |
| Description: | Motor |
| Causes: | • SBU defective • IPU defective • BCU defective • Harness between the SBU and IPU defective • Harness between the BCU-IPU defective • Standard white plate not installed correctly, or is dirty • Scanner mirrors and/or lenses are dirty or installed incorrectly |
| Remedy: | DC pick motor, no encoder feedback - staging motor - replace the “Staging motor” on page 4-79. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 165 |
| Description: | Out of Paper; Load Tray 1 (MPT) with [size] [type] The Tray 1 (MPT) No Paper Sensor indicates Tray 1 (MPT) is empty. |
| Causes: | • No Paper Sensor, PL5.3.14 • No Paper Sensor Actuator, PL5.3.15 • FRONT/DUP Harness, PL5.3.28 |
| Remedy: | 1 Fill Tray 1 (MPT) with paper. Does the error persist? Go to Step 2. Complete. 2 Check the following for evidence of fault or damage: • Tray 1 (MPT) No Paper Sensor, PL5.3.14 • Sensor Actuator, PL5.3.15 Is there any damage? Replace any damaged parts. Go to Step 3. 3 Test the Tray 1 (MPT) No Paper Sensor. Run the Service Diagnostics Tray 1 (MPT) No Paper Sensor test. Does the sensor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the Tray 1 (MPT) No Paper Sensor signal. Is there +3.3 V across P/J135-1 <=> P/J135-2? Replace the sensor. Go to Step 5. 5 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J135. 2. Check continuity between J13 <=> J134. Replace the Engine Control Board. Replace the FRONT/DUP Harness. |
| Error code: | 181 |
| Display: | Inspection is required. 181:Error |
| Description: | Scanner Unit Fan Error: Lamp Regulator Fan (Right) (D016/D097 only) The MCU issued a lock signal for the lamp regulator fan (front, right). |
| Causes: | • Fan, MCU harness loose, defective • Lamp regulator (right) fan motor defective • MCU defective • SIB defective |
| Error code: | 183 |
| Display: | Inspection is required. 183:Error |
| Description: | Scanner Unit Fan Error: Lamp Regulator Fan (Left) (D016/D097 only) The MCU issued a lock signal for the lamp regulator fan (front, left). |
| Causes: | • Scanner unit harness loose, defective • Fan, MCU harness loose, defective • Lamp regulator (left) fan motor defective • MCU defective • SIB defective |
| Error code: | 184 |
| Display: | Inspection is required. 184:Error |
| Description: | CIS transmission error When the CIS is powered on, the ADF detects one of the following abnormal conditions on the CIS unit: • The SOUT signal does not go high within 1 s after power on. • The SOUT signal goes high within 1 s after power on, but the SBU ID cannot be read after 3 attempts. |
| Causes: | • CIS unit defective • Harness between the CIS, ADF is disconnected |
| Remedy: | Cycle the power. Check to make sure the contact points of the connector and replace the Tray unit. |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 204 |
| Display: | Power OFF/ON 204:Error |
| Description: | Polygon motor error 3: XSCRDY signal error |
| Causes: | The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing. |
| Remedy: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board). |
| Error code: | 205 |
| Display: | ERROR 205 47V HEAD VOLTAGE |
| Description: | No page at DUP IN (Reserved) |
| Causes: | Disconnected cable from the polygon motor drive board or defective connection. Defective polygon motor or drive board. |
| Remedy: | 1. Check the connectors. 2. Replace the polygon motor. 3. Replace the polygon motor drive board. |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 300 |
| Description: | High voltage power output error |
| Causes: | The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit). |
| Remedy: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB. |
| Error code: | 303 |
| Display: | SYSTEM HALT (*) 303 : PCB MAIN ET |
| Description: | AC charge output error [Y] The measured voltage is not proper when IOB measures the charge output for each color. |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 304 |
| Display: | ERROR 304 USB INIT ERR |
| Description: | Charge AC bias error [K] The charge current less than 200 mkA is detected. |
| Causes: | Defective charge roller. Defective connectors. Disconnected harness. Defective high voltage power 1. |
| Remedy: | 1. Check the connectors. 2. Replace the PCU for black. 3. Replace the drum positioning plate. |
| Error code: | 305 |
| Display: | ERROR 305 USB TIME OUT |
| Description: | Charge Corona Wire Cleaner Error The charge wire cleaner did not: (1) come from the home position within 5 s, or (2) did return to the home position within 3.75 s due to wire cleaner overload. |
| Causes: | • Cleaner unit blocked or damaged • Until replacement parts become available, set SP2804 to "0" to disable the charge-corona cleaning function so the machine can operate. |
| Error code: | 306 |
| Description: | Charge AC bias error [C] The charge current less than 200 mkA is detected. |
| Causes: | Defective charge roller. Defective connectors. Disconnected harness. Defective high voltage power 1. |
| Remedy: | 1. Check the connectors. 2. Replace the PCU for cyan. 3. Replace the drum positioning plate. 4. Replace the high voltage power 1. |
| Error code: | 310 |
| Display: | Close cover 310: Top cover open |
| Description: | Printer engine cover open. |
| Causes: | 1) Check if top cover is open. 2) Check if cover switch is proper. |
| Remedy: | Close top cover. Close side cover. Replace cover switch. |
| Error code: | 311 |
| Description: | Potential sensor calibration error 2 During drum potential sensor calibration, the drum potential sensor output voltage does not meet specification when test voltages (–100V, –800V) are applied to the drum. |
| Causes: | • Potential sensor defective • Potential sensor harness disconnected • Potential sensor connector defective or disconnected • IOB defective • OPC connector defective • Development power pack defective |
| Remedy: | 1. Check if the charge cleaning HP sensor is correctly set or the sensor bracket is not bent. 2. Check the harness connection of sensor and motor. 3. Replace the charge cleaning HP sensor. 4. Replace the charge cleaning motor. |
| Error code: | 312 |
| Description: | AC charge output error [K] The machine detects the AC charge output for each color 0.3 V or less for 0.2 seconds after the machine has started to detect the AC charge output. |
| Causes: | • Loosen or broken harnesses to the HVPS: C/B • Not set or broken PCDU • Defective HVPS: C/B |
| Remedy: | 1. Close the drum securing plate firmly. 2. Make sure that the PCDU terminal plate contacts the machine terminal plate closely at the front side. 3. Set correctly or replace the PCDU. 4. Replace the harnesses to the HVPS: C/B. 5. Replace the HVPS: C/B. |
| Error code: | 314 |
| Description: | AC charge output error [C] The machine detects the AC charge output for each color 0.3 V or less for 0.2 seconds after the machine has started to detect the AC charge output. |
| Causes: | • Loosen or broken harnesses to the HVPS: C/B • Not set or broken PCDU • Defective HVPS: C/B |
| Remedy: | 1. Close the drum securing plate firmly. 2. Make sure that the PCDU terminal plate contacts the machine terminal plate closely at the front side. 3. Set correctly or replace the PCDU. 4. Replace the harnesses to the HVPS: C/B. 5. Replace the HVPS: C/B. |
| Error code: | 315 |
| Description: | AC charge output error [Y] The machine detects the AC charge output for each color 0.3 V or less for 0.2 seconds after the machine has started to detect the AC charge output. |
| Causes: | • Loosen or broken harnesses to the HVPS: C/B • Not set or broken PCDU • Defective HVPS: C/B |
| Remedy: | 1. Close the drum securing plate firmly. 2. Make sure that the PCDU terminal plate contacts the machine terminal plate closely at the front side. 3. Set correctly or replace the PCDU. 4. Replace the harnesses to the HVPS: C/B. 5. Replace the HVPS: C/B. |
| Error code: | 316 |
| Description: | Potential sensor calibration error 6 During drum potential sensor calibration, when –800V is applied to the drum, the output value is out of the prescribed range. |
| Causes: | • Potential sensor defective • Potential sensor harness disconnected • Potential sensor connector defective or disconnected • IOB defective • OPC connector defective • Development power pack defective |
| Error code: | 317 |
| Description: | Potential sensor calibration error 7 During drum potential sensor calibration, when VL is adjusted, the pattern surface potential VL pattern is not within range 0V –400V. (VL is the potential after exposing a white pattern.) |
| Causes: | • Potential sensor defective • Potential sensor harness disconnected • Potential sensor connector defective or disconnected • IOB defective • OPC connector defective • Charge corona power pack defective • Development power pack defective |
| Error code: | 321 |
| Display: | Turn power OFF and wait 321: MOTOR OVERHEAT |
| Description: | Printer cannot be used temporarily due to motor overheat. |
| Remedy: | Turn ON power after a while. |
| Error code: | 322 |
| Description: | Synchronization error The synchronization signal was not issued within 500 ms after the LD fired while the polygon motor was turning at the prescribed number of revolutions. |
| Causes: | • Laser synchronization board connectors or harness loose, disconnected, or damaged • Laser synchronization board defective or out of position • LD drive board defective |
| Remedy: | 1. Check the harness connection of the development HVPS. 2. Replace the development HVPS. 3. Replace the development unit. |
| Error code: | 335 |
| Description: | Polygon motor error 1: On timeout The XSCRDY signal did not go LOW (Active) within 10 sec. after the polygon motor was turned on. |
| Causes: | • Polygon motor drive board I/F harness loose, disconnected, or damaged • Polygon motor drive board defective • Polygon motor defective |
| Remedy: | 1. Straighten the toner supply tube. 2. Replace the toner pump. 3. Replace the toner bottle motor, and then execute SP2-253-xxx. (-001: K, -002: C, -003: M, -004: Y, -005: YMC, -006: All colors) • When executing SP2-253-xxx, make sure the following conditions; • Fist, turn off and on the machine after opening the front left or right door. • Make sure that the target color toner bottle is installed and the toner hopper cover is close. • Enter the SP mode, and then execute SP2-253-xxx. |
| Error code: | 336 |
| Description: | Polygon motor error 2: Off timeout The XSCRDY signal did not go HIGH (Inactive) within 3 sec. after the polygon motor was turned off. |
| Causes: | • Polygon motor drive board I/F harness loose, disconnected, or damaged • Polygon motor drive board defective • Polygon motor defective |
| Error code: | 337 |
| Description: | Polygon motor error 3: XSCRDY signal error The XSCRDY signal did not go HIGH (Inactive) after the polygon motor had been rotating normally for 200 ms. |
| Causes: | • Polygon motor drive board I/F harness loose, disconnected, or damaged • Polygon motor drive board defective • Polygon motor defective |
| Error code: | 338 |
| Description: | Polygonal Mirror Motor Error 4: Unstable Timeout The XSCRDY signal was detected LOW) (Active) after the polygonal mirror motor switched on, but the signal was not detected LOW after 1 sec., and was not detected after another 500 ms. |
| Causes: | • I/F harness of the polygonal mirror motor disconnected or defective. • Polygonal mirror motor or polygonal mirror motor drive board defective. |
| Error code: | 340 |
| Description: | TD sensor output error TD sensor output voltage (Vt), measured during each copy cycle, is detected 10 times at one of the following levels: Vt = 0.5 volts or lower Vt = 4.0 volts or higher |
| Causes: | • TD sensor defective • TD sensor harness disconnected • TD sensor connector disconnected or defective • IOB defective • Toner bottle motor defective • Note: When the TD sensor is defective, the toner supply is controlled using pixel count and the ID sensor. |
| Error code: | 341 |
| Description: | TD sensor adjustment error 1 During the TD sensor auto adjustment, the TD sensor output voltage (Vt) is 2.5 volts or higher even though the control voltage is set to the minimum value (PWM = 0). When this error occurs, SP2-906-1 reads 0.00V. Note: This SC is released only after correct adjustment of the TD sensor has been achieved. Switching the machine off and on will cancel the SC display, but does not release ID sensor toner supply. |
| Causes: | • TD sensor defective • TD sensor harness disconnected • TD sensor connector disconnected or defective • IOB defective • Toner bottle motor defective • Note: When the TD sensor is defective, the toner supply is controlled using pixel count and the ID sensor. |
| Error code: | 342 |
| Description: | TD sensor adjustment error 2 During the TD sensor auto adjustment, the TD sensor output voltage (Vt) does not enter the target range (3.0 +- 0.1V) within 20 s. When this error occurs, the display of SP2-906-1 reads 0.00V. Note: This SC is released only after correct adjustment of the TD sensor has been achieved. Switching the machine off and on will cancel the SC display, but does not release ID sensor toner supply. |
| Causes: | • TD sensor defective • TD sensor harness disconnected • TD sensor connector disconnected or defective • IOB defective |
| Error code: | 345 |
| Description: | Development output abnormal The high voltage applied to the development unit is detected 10 times higher than the upper limit (45%) of PWM. |
| Causes: | • Development power pack defective • Development bias leak due to poor connection, defective connector |
| Remedy: | 1. Check or replace the drum cleaning blade. 2. Clear the waste toner stuck in the drum cleaning unit. 3. Check the harness connection of the drum cleaning motor. 4. Remove the obstruction around the drum cleaning motor shaft. 5. Replace the drum cleaning motor. |
| Error code: | 350 |
| Description: | ID sensor error 1 One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. Vsp greater than or equals 2.5V Vsg less than 2.5 Vsp = 0V Vsg = 0 |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 351 |
| Description: | ID sensor error 2 The ID sensor output voltage is 5.0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 352 |
| Description: | ID sensor error 3 For 2 s during the ID sensor pattern check, the ID sensor pattern edge voltage is not 2.5V or the pattern edge is not detected within 800 ms. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 353 |
| Description: | ID sensor error 4 One of the following ID sensor output voltages is detected at ID sensor initialization. Vsg less than 4.0V when the maximum PWM input (255) is applied to the ID sensor. Vsg greater than or equal to 4.0V when the minimum PWM input (0) is applied to the ID sensor. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 354 |
| Display: | Set new fuser 354: Fuser life |
| Description: | Fuser life (occurs when fuser life continuation is OFF). |
| Causes: | Right after replacing fuser? |
| Remedy: | Check fuser life. Replace fuser. |
| Error code: | 355 |
| Display: | Set new belt 355: Belt life |
| Description: | Belt life notified (alarm). Print N-count by opening and closing cover. |
| Causes: | Right after replacing belt? |
| Remedy: | Check belt life. Replace belt. |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 430 |
| Description: | Quenching lamp error At the completion of auto process control initialization, the potential of the drum surface detected by the potential sensor is more than -400V, the prescribed value. |
| Causes: | • Quenching lamp defective • Quenching lamp harness disconnected • Quenching lamp connector loose, defective |
| Error code: | 440 |
| Description: | Transfer Output Error. A high voltage feedback voltage of less than 0.5 V was detected for 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 441 |
| Description: | Image transfer unit motor error When the motor is ON, the machine monitors the lock signals every 100 ms. If the High status occurs 20 times consecutively, the machine judges that the motor is not rotating correctly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Shorted 24 V fuse on the PSU. Defective interlock systeme PSU. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system |
| Error code: | 490 |
| Display: | Set 490: No paper in MP tray (* stands for A4 B4, etc.) |
| Description: | ITB (Image Transfer Belt) Unit Set Error |
| Causes: | The TM sensor does not detect the reflection from the ITB. |
| Remedy: | • No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S |
| Error code: | 495 |
| Description: | Toner collection motor error The machine detects that the waste toner bottle is not set for one second when the toner collection motor is turned off. |
| Causes: | • Toner collection motor damaged • Disconnect or defective harness • Defective BCU |
| Remedy: | 1. Check or replace the harness. 2. Replace the toner collection motor. 3. Replace the BCU 4. Check and retry the connecting procedure. |
| Error code: | 496 |
| Description: | Toner collection bottle error The toner collection bottle set switch remains off when the front door is closed. |
| Causes: | • No toner collection bottle set • Poor connection of the switch connector |
| Error code: | 497 |
| Description: | Temperature sensor error If the output value of the thermal sensor is 0.5 V or lower or 2.8 V or higher, it is judged as a sensor error and the presumptive temperature, 23 °C, is applied. If the thermal sensor is judged to have encountered a sensor error three times consecutively, the machine issues SC497-00, stops using the sensor, and feeds back the presumptive value. * However, if the power is switched off and then back on, the machine resumes its attempt to use the sensor. |
| Causes: | Loose connection/Disconnected connector. Defective sensor. |
| Remedy: | • Clean/Replace the sensor. • Reconnect the connector. • Check the harness |
| Error code: | 501 |
| Display: | Service Call 501: Error |
| Description: | Tray 1 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503 |
| Display: | Service Call 503: Error |
| Description: | Tray 3 must be rebuilt |
| Causes: | (A model other than D581) Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. (D581) Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 504 |
| Description: | Tray 4 must be rebuilt |
| Causes: | The 2nd tray of D580, 1st tray of D580 when D579 and D580 are attached, the bottom D579 when two units of D579 are attached, or D631 when D581 and D631 are attached. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection D581 when D579 and D581 are attached.Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 507 |
| Description: | Duplex unit must be rebuilt |
| Causes: | • Feed motor defective • Feed motor connector disconnected • Obstacle interfering with mechanical movement of motor. |
| Remedy: | 1. Replace the tray 3 or 4 lift motor. 2. Replace the tray 3 or 4 lift sensor. 3. Check or clear obstacles around pick-up solenoid 3 or 4. |
| Error code: | 510 |
| Display: | SYSTEM HALT (*) 510 : X ORGIN |
| Description: | Replace green developer |
| Causes: | • Tray lift motor defective or connector disconnected • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Remedy: | 1. Check the harness connection or replace it. 2. Replace the bypass tray lift motor. 3. Replace the bypass upper limit sensor. 4. Replace the bypass lower limit sensor. 5. Check or clear obstacles around the bypass pick-up solenoid. |
| Error code: | 515 |
| Display: | ERROR 515 DETECTION ERROR |
| Description: | DADF belt should be replaced |
| Causes: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors • Paper or other obstacle trapped between tray and motor • Motor mechanical overload due to obstruction • Return sensor or HP sensor defective or dirty Note • This problem will not issue the SC code on the operation panel. • The machine will prompt the operator to reset tray by opening and closing it. • If the problem persists, the machine will display again and the tray cannot be used. |
| Error code: | 520 |
| Description: | Replace optics filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 521 |
| Description: | Replace particle filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 531 |
| Description: | Fusing Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the fusing fan motor. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 550 |
| Description: | Fusing Web End Web end detected 5 times within 500 ms and web motor continues to rotate 40 s. If web end is detected for another 500 ms, then the SC is logged. |
| Causes: | • Web end (requires replacement) • Web end sensor defective • Note: After replacing the web with a new one, reset SP1902 001 to "0" to release SC550. |
| Remedy: | 1 Check after turning the power OFF and ON. Does the error recur even when the power is turned off and back on again? Go to Step [2]. End of procedure 2 Check the connection of the FAN MAIN and the FAN DUP Check the connection state of the following items. • FAN MAIN - LVPS • FAN DUP - PWBA DUP Are P/J503 and P/J427 connected correctly? Go to Step [3]. Reconnect FAN MAIN and FAN DUP correctly. 3 Check the power voltage supply to FAN DUP. Measure the voltage between PWBA DUP ground <=> P/J427-1PIN. Is the power voltage (+24 V) output? Replace the FAN DUP. Go to Step [4]. 4 Check the connection between PWBA DUP and PWBA MCU Check the connection state between PWBA DUP and PWBA MCU. Are P/J428, P/J2720, P/J272, and P/J27 connected correctly? Go to Step [5]. Reconnect the P/J428, P/J2720, P/J272, and P/J27 correctly. 5 Check the continuity of the HARNESS ASSY DUP UNIT Is there normal continuity between P/J428 and P/J2720? Go to Step [6]. Replace the HARNESS ASSY DUP UNIT. 6 Check the continuity of the HARNESS ASSY FRONT COVER Is there normal continuity between P/J2720 and P/J272? Go to Step [7]. Replace the HARNESS ASSY FRONT COVER. 7 Check the continuity of the HARNESS ASSY R SIDE Is the continuity between P/J27 <=> P/J2720 normal? Go to Step [6]. Replace the HARNESS ASSY R SIDE. 8 Check the power voltage supply to PWBA DUP 1. Close the interlock switch (HARNESS ASSY INTERLOCK) before performing the following work. 2. Measure the voltage between PWBA MCU ground <=> P/J27-A17, A18PIN. Is the power voltage (approx. +24 V) output? Go to Step [9]. Replace the PWBA MCU. 9 Replace of the PWBA DUP Replace the PWBA DUP. Was the trouble fixed? End of procedure Go to Step [10]. 10 Check the power voltage supply to FAN MAIN Measure the voltage between LVPS ground <=> P503-1PIN. Is the power voltage (+24 V) output? Replace the FAN MAIN. Go to Step [11]. 11 Check the continuity of the HARNESS ASSY LV TOP Is the continuity between P/J14 <=> P/J501 normal? Go to Step [12]. Replace the HARNESS ASSY LV TOP. 12 Check the power voltage output from the LVPS. 1. Measure the voltage between LVPS ground <=> P503-1PIN. 2. Close the interlock switch (HARNESS ASSY INTERLOCK) before performing the following work. Is the power voltage (approx. +24 V) output? Replace the PWBA MCU. Replace the LVPS. |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 555 |
| Description: | Fusing Heater error: End The fusing heater keeps full power for 9 seconds or more. |
| Causes: | Defective thermistors. Broken heater cables. |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 569 |
| Description: | Pressure roller contact sensor error Pressure roller contact sensor does not detect the pressure roller position three times. |
| Causes: | • Broken or defective pressure roller contact sensor • Deformed or broken pressure roller contact sensor feeler • Defective pressure roller contact motor • Defective fusing unit |
| Remedy: | 1. Check or replace the harness of the pressure roller contact sensor. 2. Replace the pressure roller contact sensor. 3. Replace the pressure roller contact motor. |
| Error code: | 590 |
| Description: | Toner collection motor error The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on. |
| Causes: | • Motor lock due to obstruction • Motor driver board defective • Motor connection loose, defective • Toner collection motor sensor disconnected, sensor defective • Rotational transmission shaft (o6 x 30) missing |
| Error code: | 599 |
| Description: | 1-bin Exit Motor Error (Japan Only) The transport lock sensor output does not change within 300 ms after the motor switches on. |
| Causes: | • Motor overload • Motor driver defective |
| Error code: | 610 |
| Display: | ERROR 610 NOT FILLUP |
| Description: | Mechanical counter error: Bk This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 611 |
| Display: | ERROR 611 Case Weight |
| Description: | Mechanical counter error: FC This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 612 |
| Display: | ERROR 612 INK LVL LOW |
| Description: | BICU - ADF communication/command abnormal A command that cannot be executed was sent from the main machine to the ADF. |
| Causes: | • A software error, result of an abnormal procedure. |
| Remedy: | Enter the cartridge weight from "CART WEIGHT" menu of "SET UP". |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 623 |
| Description: | 2nd Paper Bank communication error An error code is issued from the paper bank unit. |
| Causes: | Loose connection. Defective paper bank. |
| Remedy: | • Reconnect the connector. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 624 |
| Description: | 4th Paper Bank (option) communication error This SC is not issued for this machine. When a communication error signal between the 3rd paper bank and 4th paper bank is received. |
| Causes: | • Loose or disconnected connector |
| Remedy: | Check the connection between the main machine and paper feed unit. |
| Error code: | 626 |
| Description: | BICU/LCT communication/timeout error After 1 data frame is sent to the LCT, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line connection unstable • External noise on the line |
| Remedy: | 1. Check the connection between the above devices. 2. Replace the RCB. 3. Replace the BCU. |
| Error code: | 627 |
| Display: | ERROR 627 INSERT CARTRIDGE |
| Description: | BICU/LCT communication/break reception error During communication with the LCT, the BICU received a break (Low) signal. |
| Causes: | • Serial line connection unstable • External noise on the line |
| Error code: | 650 |
| Description: | @Remote communication error 1 A dial-up or modem error occurred during @Remote operation. (This error occurs only during @Remote operation.) |
| Causes: | • Modem line disconnected • Modem board missing or not properly installed |
| Error code: | 651 |
| Description: | @Remote communication error 2 An illegal dial-up to the service center was attempted by @Remote. |
| Causes: | • Software bug |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 700 |
| Description: | Original stopper HP error When the pick-up motor turns on clockwise, the original stopper HP sensor does not detect the home position of the original stopper. |
| Causes: | • Detached timing belt for the pick-up motor • Defective original stopper HP sensor • Defective pick-up motor • Defective DF drive board |
| Remedy: | 1. Check the timing belt for the pick-up motor. 2. Replace the DF drive board if the pick-up motor does not work correctly. 3. Replace the pick-up motor. 4. Replace the original stopper HP sensor. |
| Error code: | 701 |
| Description: | ADF Pickup Roller Release Malfunction (D016/D097 only) The pick-up roller HP sensor does not activate or de-activate when the pick-up motor turns on. |
| Causes: | • HP sensor connector, harness loose, broken, defective • Pick-up motor connector, harness loose, broken defective • Pick-up roller HP sensor defective • Pick-up motor defective • ADF main control board defective |
| Remedy: | 1. Check the harness connections. 2. Replace the pick-up roller HP sensor. 3. Replace the pick-up motor. 4. Replace the main board of the ADF. |
| Error code: | 720 |
| Description: | Fan folder transport motor error A transport motor lock signal was detected for more than 5 sec. while the motor was running. |
| Causes: | • Transport motor harness connector loose, disconnected, broken • Motor overload due to an obstruction • Transport motor defective • Fan folder unit MCU defective |
| Error code: | 721 |
| Description: | Jogger motor error • Jogger HP sensor does not detect the jogger fence for 2000ms after the jogger unit has moved to its home position. • Jogger HP sensor does not turn off 300 ms after the jogger unit has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective jogger HP sensor • Overload on the jogger motor • Defective jogger motor • Defective main board • Disconnected or defective harness |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the jogger HP sensor (if the jogger motor works correctly). 3. Replace the jogger motor (if the jogger motor does not work). 4. Replace the finisher main board. |
| Error code: | 723 |
| Description: | Stack feed-out motor error • Stack feed-out HP sensor does not detect the home position of the stack feedout belt 3000ms after the stack feed-out belt has moved to its home position. • Stack feed-out HP sensor does not turn off 200 ms after the stack feed-out belt has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code |
| Causes: | • Defective stack feed-out HP sensor • Overload on the stack feed-out motor • Defective stack feed-out motor • Defective main board • Disconnected or defective harness |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the stack feed-out HP sensor (if the stack feed-out motor works correctly). 3. Replace the stack feed-out motor (if the stack feed-out motor does not work). 4. Replace the finisher main board. |
| Error code: | 724 |
| Description: | Finisher staple hammer motor error Stapling does not finish within 150 ms after the staple hammer motor turned on. Staple mode cannot be used. |
| Causes: | • Staple jam • Stapler overload caused by trying to staple too many sheets • Staple hammer motor connector or harness loose, broken, defective • Staple hammer motor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the staple hammer motor HP sensor if the motor is rotating. 4. Replace the finisher main board. |
| Error code: | 725 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor. 4. Replace the finisher main board. |
| Error code: | 726 |
| Description: | Front shift jogger motor error (B703) The sides fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift jogger motor disconnected, defective • Shift jogger motor overloaded due to obstruction • Shift jogger HP sensor disconnected, defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift jogger HP sensor 4. Replace the shift jogger motor. 5. Replace the finisher main board. |
| Error code: | 727 |
| Description: | Rear shift jogger motor (B703) The side fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code |
| Causes: | Motor harness disconnected, loose, defective Motor defective Motor overload HP defective boar |
| Error code: | 728 |
| Description: | Shift jogger retraction motor error (B703) The side fences do not retract within the prescribed time after the retraction motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray jogger lift HP sensor. 4. Replace the shift jogger retraction motor. 5. Replace the finisher main board. |
| Error code: | 729 |
| Description: | Finisher punch motor error After the punch motor is turned on, the punch HP sensor does not activate within 250 ms. |
| Causes: | • Punch motor harness or connector loose, broken, defective • Punch motor defective or overloaded due to obstruction • Punch HP sensor connector or harness loose, broken, defective • Punch HP sensor defective |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 732 |
| Description: | Finisher shift roller motor error The shift roller HP sensor does not activate within the prescribed time after the shift roller motor turns on. After 2 counts, the SC is logged as a jam. |
| Causes: | • Shift roller HP sensor defective • Sensor harness disconnected, defective • Shift roller motor defective • Finisher main board defective • Shift roller motor overload |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray exit motor. 4. Replace the finisher main board. |
| Error code: | 733 |
| Description: | Finisher lower tray lift motor error After the lift motor switches on to lift the tray, paper height sensor 2 does not detect the top of the paper stack, or after the motor reverses to lower the stack the top of the stack remains detected (the status of paper height sensor 1 does not change). After 2 counts, the SC is logged as a jam. |
| Causes: | • Paper height sensor 1 or 2 defective • Sensor harness disconnected, defective • Tray lift motor defective • Finisher main board defective • Tray lift motor overload |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the stapler exit motor. 4. Replace the finisher main board. |
| Error code: | 735 |
| Description: | Finisher pre-stack motor error The pre-stack motor starts but does not return to the home position within 400 pulses. After 2 counts, the SC is logged as a jam. Motor does not return to the home position within 280 pulses immediately before or after pre-stacking. After 2 counts, the SC is logged as a jam. |
| Causes: | • Jogger HP sensor defective • Sensor harnesses disconnected, defective • Pre-stack motor defective • Finisher main board defective • Pre-stack motor overload |
| Remedy: | 1. Check or clear obstacles around the motor drive. 2. Check the harness connection. 3. Replace the staple tray junction gate HP sensor. 4. Replace the staple junction gate motor. 5. Replace the finisher main board. |
| Error code: | 736 |
| Description: | Finisher paper exit guide plate motor error The paper exit guide plate motor starts but the paper exit guide plate HP sensor does not activate within 750 ms. After 2 counts, the SC is logged as a jam. |
| Causes: | • Guide plate HP sensor defective • Sensor harness disconnected, defective • Paper exit guide plate motor defective • Finisher main board defective • Guide plate motor overload. |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the pre-stack junction gate HP sensor. 4. Replace the pre-stack junction gate motor. 5. Replace the finisher main board. |
| Error code: | 737 |
| Description: | Trimmed staple waste hopper full The hopper that holds the waste from staple trimming is full. |
| Causes: | • Staple waste hopper full • Staple waste sensor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the pre-stack transport motor. 4. Replace the finisher main board. |
| Error code: | 738 |
| Description: | Finisher pressure plate motor error The pressure plate motor switches on but does not return to the home position within the prescribed time after 2 counts. |
| Causes: | • HP sensor defective • Harness disconnected, defective • Motor defective • Finisher main board defective • Motor overload |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the pre-stack junction gate release HP sensor. 4. Replace the pre-stack junction gate release motor. 5. Replace the finisher main board. |
| Error code: | 739 |
| Description: | Finisher folder plate motor error The folder plate motor turns on but the plate does not return to the home position within the prescribed time for 2 counts. |
| Causes: | • Plate HP sensor defective • Harness disconnected, defective • Folder plate motor defective • Finisher main board defective • Folder plate motor overload |
| Error code: | 740 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished after a certain time. For the 1000-sheet booklet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 741 |
| Description: | Finisher corner stapler rotation motor error The stapler does not return to its home position within the specified time after stapling. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective stapler rotation motor • Overload to the stapler rotation motor • Defective stapler rotation HP sensor |
| Remedy: | 1. Replace the stapler rotation motor. 2. Replace the stapler rotation HP sensor. |
| Error code: | 742 |
| Description: | Finisher stapler movement motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished for a certain time. For the 1000-sheet booklet finisher • The stapler HP sensor is not activated within the specified time after the stapler motor turned on. (first detection: jam error, consecutive twice detection SC code). |
| Causes: | • Motor overload • Loose connection of the stapler home position sensor • Loose connection of the stapler movement motor • Defective stapler home position sensor • Defective stapler movement motor |
| Remedy: | 1. Check the connection of the stapler movement motor. 2. Check the connection of the stapler home position sensor. 3. Replace the stapler home position sensor. 4. Replace the stapler movement motor. |
| Error code: | 743 |
| Description: | Booklet stapler motor error 1 The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher The front stapler unit saddle-stitch motor does not start operation within the specified time. |
| Causes: | • Motor overload • Loose connection of the front stapler motor • Defective front stapler motor |
| Remedy: | Replace the front stapler motor. |
| Error code: | 744 |
| Description: | Booklet staple motor error 2 The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher The rear stapler unit saddle-stitch motor does not start operation within the specified time. |
| Causes: | • Motor overload • Loose connection of the rear stapler motor • Defective rear stapler motor |
| Remedy: | Replace the front stapler motor. |
| Error code: | 750 |
| Description: | 1000/3000-sheet (booklet) finisher: Tray lift motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. |
| Causes: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor |
| Remedy: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor. |
| Error code: | 753 |
| Description: | Return roller motor error Occurs during the operation of the lower tray pressure motor. |
| Causes: | • Motor harness disconnected, loose, defective • Motor overloaded • Home position sensor harness disconnected, loose, defective • Home position defective |
| Remedy: | 1. Check the connections of the stacking sponge roller motor. 2. Check the connections of the stacking sponge roller HP sensor. 3. Replace the stacking sponge roller motor. 4. Replace the stacking sponge roller HP sensor. |
| Error code: | 754 |
| Description: | Drag Roller Motor Error: 3K Finisher B830 The stacking roller drag motor did not turn on. |
| Causes: | • Motor harness loose, broken, defective • Motor defective • Finisher control board defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the drag roller motor. 4. Replace the finisher main board. |
| Error code: | 755 |
| Description: | Shift Motor Error: 3K Finisher (B830) The shift tray half-turn sensors: Failed twice to detect the shift tray at the home position at the specified time. -or- Failed twice to detect that the shift tray had left the home position. The 1st failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | If the motor is operating • Half-turn sensor 1, 2 harnesses loose, broken, defective • One of the half-turn sensors defective If the motor is not operating: • Motor blocked by an obstruction • Motor harness loose, broken, defective • Motor defective • Finisher main board defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray half-turn sensor 1 or 2. 4. Replace the shift motor. 5. Replace the finisher main board. |
| Error code: | 756 |
| Description: | Finisher pick-up solenoid error (with the side tray installed) |
| Causes: | • Solenoid harness loose, broken • Solenoid obstructed • Solenoid defective |
| Remedy: | 1. Check or replace the solenoid harness. 2. Replace the pick-up solenoid. |
| Error code: | 757 |
| Description: | Z-Folding unit error 7 The machine could not write to the EEPROM two times (one after the other). |
| Causes: | • EEPROM defective, replace Z-Fold main control board |
| Error code: | 760 |
| Description: | Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Punch HP sensor disconnected, defective • Punch motor disconnected or defective • Punch motor overload due to obstruction |
| Remedy: | 1. Check the connections and cables for the punch motor and HP sensor. 2. Check for blockages in the punch motor mechanism. 3. Replace the punch HP sensor and/or punch motor 4. Replace the finisher main board. |
| Error code: | 761 |
| Description: | Finisher folder plate motor error The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Remedy: | 1. Check the connections and cables for the folder plate motor and HP sensor. 2. Check for blockages in the folder plate motor mechanism. 3. Replace the folder plate HP sensor and/or folder plate motor 4. Replace the finisher main board. |
| Error code: | 762 |
| Description: | Front fold plate HP sensor error The state (on/off, off/on) of the front fold plate HP sensor in the fan fold unit did not change 1 sec. after the plate started to move. |
| Causes: | • Fold plate motor (F) harness connector loose, disconnected, broken • Front fold plate HP sensor harness connector loose, disconnected, broken • Fold plate motor (F) defective • Front fold plate HP sensor defective • Undetected paper is jamming the action of the motor or fold plate • Fan folder unit MCU defective |
| Error code: | 763 |
| Description: | Rear fold plate HP sensor error The state (on/off, off/on) of the rear fold plate HP sensor in the fan fold unit did not change 1 sec. after the plate started to move. |
| Causes: | • Fold plate motor (R) harness connector loose, disconnected, broken • Rear fold plate HP sensor harness connector loose, disconnected, broken • Fold plate motor (R) defective • Rear fold plate HP sensor defective • Undetected paper is jamming the action of the motor or fold plate • Fan folder unit MCU defective |
| Error code: | 764 |
| Description: | Paper position sensor slide motor error The paper position sensor moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the paper position sensor slide motor. 2. Replace the paper position sensor slide motor. |
| Error code: | 765 |
| Description: | Fold unit bottom fence motor error The bottom fence of the fold unit moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the fold unit bottom fence motor. 2. Defective fold unit bottom fence motor. |
| Error code: | 766 |
| Description: | Stacking sponge roller motor error The sponge roller moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the stacking sponge roller motor. 2. Defective stacking sponge roller motor. |
| Error code: | 767 |
| Description: | Stack junction gate motor error The stack junction gate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the stack junction gate motor. 2. Defective stack junction gate. |
| Error code: | 770 |
| Description: | Shift motor error The shift motor HP sensor does not detect any change for 1.86 seconds after the shift motor has turned on at power on or during its operation. |
| Causes: | Defective shift motor. Defective shift motor HP sensors. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 780 |
| Description: | Z-Fold Feed Motor Error The feed motor that drives the feed rollers and exit rollers in the Z-fold unit is not operating. The 1st alert signals a jam, the 2nd alert triggers this SC. |
| Causes: | • Motor harness loose, broken, defective • Motor blocked by an obstruction • Motor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the feed motor. |
| Error code: | 781 |
| Description: | Z-Fold Lower Stopper Motor Error The lower stopper failed to leave the home position with the specified number of motor pulses. • The 1st detection failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | • Lower stopper motor disconnected, defective • Lower stopper motor overloaded due to obstruction • Lower stopper HP sensor disconnected, defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the lower stopper motor. |
| Error code: | 782 |
| Description: | Z-fold Upper Stopper Motor The upper stopper failed to leave the home position with the specified number of motor pulses. The 1st detection failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | • Upper stopper motor disconnected, defective • Upper stopper motor overloaded due to obstruction • Upper stopper HP sensor disconnected, defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the upper stopper motor. |
| Error code: | 784 |
| Description: | Z-Fold Timing Sensor Adjustment Error 1 The output voltage light emitted from the sensor changed, but the return input was not sufficient to attain V0. |
| Causes: | • Sensor, mirror dirty from paper dust, other particles • Harness loose, broken, defective • Mirror out of position |
| Remedy: | 1. Check the harness connection. 2. Replace the fold timing sensor. |
| Error code: | 785 |
| Description: | Z-Fold Timing Sensor Adjustment Error 2 The output voltage light emitted from the sensor changed, but the return input was not sufficient to attain V0. |
| Causes: | • Sensor, mirror dirty from paper dust, other particles • Harness loose, broken, defective • Mirror out of position |
| Remedy: | 1. Check the harness connection. 2. Replace the leading edge sensor. |
| Error code: | 786 |
| Description: | Z-Fold Memory Error Several attempts to write to the Z-fold memory failed. |
| Causes: | • Turn the machine power off/on • EEPROM on Z-Folder main board defective |
| Remedy: | 1. Check the harness connection. 2. Replace the main board. |
| Error code: | 790 |
| Description: | PCB fan error: Folder Unit The machine detected a continuous lock signal from the PCB cooling fan on the PSU for 20 sec. |
| Causes: | • Fan harness connector loose, disconnected, broken • Overload on the fan motor due to physical obstruction such has undetected paper, etc. • Fan defective • MCU folder unit defective |
| Error code: | 817 |
| Display: | SYSTEM HALT (*) 817 : FW/SaveArea |
| Description: | Monitor error This is a file detection and electronic file signature check error when the boot loader attempts to read the self-diagnostic module, system kernel, or root system files from the OS Flash ROM, or the items on the SD card in the controller slot are false or corrupted. |
| Causes: | OS Flash ROM data defective. SD card data defective. Change the controller firmware. Use another SD card. |
| Remedy: | • Change the controller firmware. • Use another SD card. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 833 |
| Display: | SYSTEM HALT (*) 833 : FW/PRN MDL |
| Description: | Self-diagnostic error 8: Engine I/F ASIC |
| Causes: | [0F30] [0F31] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. [0F41] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. |
| Error code: | 834 |
| Display: | SYSTEM HALT (*) 834 : FW/SV MDL |
| Description: | Self-diagnostic error 9: Optional Memory RAM DIMM 5101 The write/verify check for the optional RAM chip on the engine mother board gave an error. |
| Causes: | • Controller defective • Mother board defective |
| Remedy: | Replace the controller board. |
| Error code: | 850 |
| Description: | Net I/F error Duplicate IP addresses. Illegal IP address. Driver unstable and cannot be used on the network |
| Causes: | • IP address setting incorrect • NIB (PHY) board defective • Controller board defective |
| Remedy: | Turn the main switch off and on. |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 910 ... 914 |
| Display: | Power Off/on 910: Error to 914: Error |
| Description: | 910 B External controller error 1 911 B External controller error 2 912 B External controller error 3 913 B External controller error 4 914 B External controller error 5 The external controller alerted the machine about an error. |
| Causes: | • Refer to the instructions for the external controller |
| Error code: | 919 |
| Display: | Power Off/on 919: Error |
| Description: | Power Supply Fan Error |
| Causes: | • Controller RW3600 power outtage • Controller RW3600 rebooted • Connection to Controller RW3600 loose |
| Remedy: | 1 Is CN17 on the printer controller board properly connected? Go to step 2. Connect CN17. 2 Is CN6 on the CK2 daughter board properly connected? Go to step 3. Connect CN6. 3 Is +24 V present between pins 1 and 3 of connector CN6 on the CK2 daughter board? Replace the power supply fan. Replace the printer controller board. 4 Did either exchange solve the problem? Problem solved. Replace the CK2 daughter board. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 953 |
| Description: | NVRAM Chip Failure |
| Causes: | • Firmware bug • Update the scanner firmware • IPU defective |
| Remedy: | Indicates the NVRAM chip on the interconnect board has failed. Replace the interconnect board. |
| Error code: | 954 |
| Description: | NVRAM CRC Failure |
| Causes: | • Firmware bug • IPU defective |
| Remedy: | Indicates the NVRAM experienced a CRC failure. Replace the interconnect board. |
| Error code: | 955 |
| Description: | Code CRC <loc> |
| Causes: | • Firmware bug • Hard disk unit defective • Controller defective • MCU defective • IPU defective |
| Remedy: | Replace the system board. Where <loc> = CRC Failure or ECC Failure on the system board. |
| Error code: | 964 |
| Description: | Emulation Error |
| Causes: | • Software defective |
| Remedy: | Indicates a failure within the Download Emulation which is programmed into the code overlay card. The specific error is as follows: 964 - Download Emulation CRC Failure. Checksum Failure. |
| Error code: | 984 |
| Display: | Service call 984: Error. |
| Description: | <device> |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected |
| Remedy: | Invalid command parameter received by the specified device. Note: Service errors 980 thru 984 <device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 985 |
| Display: | Service call 985: Error |
| Description: | Transfer Belt Thermistor Error |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU/controller disconnected |
| Remedy: | 1 Are connectors CN407 and CN411 on the sensor board connected properly? Go to step 2. Plug the connector in securely. 2 Is connector CN15 on the printer controller board connected properly? Replace the transfer belt unit. If the problem remains, replace the printer controller board. Plug the connector in securely. |
| Error code: | 986 |
| Display: | Service call 986: Error |
| Description: | Transparency (OHP) Sensor Error |
| Causes: | • Controller (SIMAC) board defective • BICU defective • BICU Controller disconnected |
| Remedy: | 1 Are connectors CN4 (light emitting) and CN5 (light receiving) on the CK1 daughter board connected properly? Go to step 2. Plug the connector in securely. 2 Test the sensor. While actuating the sensor, does the voltage fluctuate between 0 V and +5 between pins 2 and 3 of connector CN7 of the printer controller board? Replace the printer controller board. Replace the MPF unit. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 994 |
| Display: | Service Call 994:Error |
| Description: | Density Sensor Error |
| Causes: | • No action required because this SC does not interfere with operation of the machine. |
| Remedy: | 1 Is the front door fully closed? Go to step 2. Close the front door. 2 Is the density sensor actuator stuck in place? Release the density sensor actuator. Go to step 3. 3 Are connectors CN406 and CN407 on the sensor board connected properly? Go to step 4. Plug the connector in securely. 4 Is connector CN15 on the printer controller board connected properly? Replace the density sensor. Go to step 5. Plug the connector in securely. 5 Did replacing the density sensor fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
Название
RICOH TYPE H Скрепки в картридже
RICOH TYPE H Скрепки (5 упаковок)
RICOH TYPE L Скрепки буклетные в картридже
RICOH TYPE L Скрепки буклетные (в упаковке 4*2000шт.)
RICOH TYPE 6210D / MP 9002 Тонер-картридж
RICOH TYPE 24 Девелопер черный
RICOH Фотобарабан
