Ricoh MPC2500
Рейтинг
Модули
ELECTRICAL SECTION 2
Controller
Toner Hopper 2
FRAME SECTION 2
FUSING UNIT 2
2nd Paper Tray
Frame Section 4
FUSING UNIT 3
ELECTRICAL SECTION 1
Drive Section 1
9.1st Paper Tray
ELECTRICAL SECTION 3
DUPLEX UNIT 1
Paper exit
FUSING UNIT 1
SCANNER SECTION 2
FRAME SECTION 1
DRIVE SECTION 3
PAPER REGISTRATION 1
DUPLEX UNIT 2
DRIVE SECTION 4
DRIVE SECTION 2
Paper Transfer Section
EXTERIOR 1
Toner Hopper 1
PAPER FEED SECTION
SCANNER SECTION 3
Frame Section 3
EXTERIOR 3
LASER UNIT
By-pass Feed Section 2
By-pass Feed Section 1
EXTERIOR 2
OPERATION PANEL
PAPER REGISTRATION 2
PCU/Transfer Unit
Scanner Section 1
Детали 9.1st Paper Tray
| Деталь: | Power Pack:CBTTS |
| Парткод: | AZ32 0167 |
| Деталь: | Power Pack Bracket |
| Парткод: | B238 5830 |
| Деталь: | Harness - BICU Power Source |
| Парткод: | B238 5323 |
| Деталь: | Harness Clamp |
| Парткод: | B238 5831 |
| Деталь: | Cover - Power Supply Unit |
| Парткод: | B238 5812 |
| Деталь: | Fan Motor - DC24V 1.92W |
| Парткод: | GX64 0027 |
| Деталь: | Power Supply Unit:Athena:EU/AA |
| Парткод: | AZ24 0105 |
| Деталь: | Power Supply Unit:Athena:DOM/NA |
| Парткод: | AZ24 0114 |
| Деталь: | Harness - High Voltage Line B |
| Парткод: | B238 5382 |
| Деталь: | Inlet |
| Парткод: | B238 5341 |
| Деталь: | Harness:Dehumidifier:Scanner:Exp |
| Парткод: | B237 5339 |
| Деталь: | Harness - Power Supply Unit |
| Парткод: | B238 5332 |
| Деталь: | Harness - Dehumidifier |
| Парткод: | B237 5337 |
| Деталь: | Harness:Power Supply Unit:Relay |
| Парткод: | B238 5342 |
| Деталь: | Harness:Power Supply Unit:Finisher |
| Парткод: | B238 5335 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Spacer:Kgps-8rfv0 |
| Парткод: | 11 050 648 |
| Деталь: | Clamp - LES-1017 |
| Парткод: | 11 050 521 |
| Деталь: | Edge Saddle - Les-1010 |
| Парткод: | 11 050 518 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Tapping Screw:3x20 |
| Парткод: | 0451 3020N |
| Деталь: | Rocker Switch:Sddje13200 |
| Парткод: | 12 042 570 |
| Деталь: | Harness - HDD Power Source |
| Парткод: | B237 5726 |
| Деталь: | Harness - HDD |
| Парткод: | B238 5396 |
| Деталь: | HDD Cover |
| Парткод: | B238 5883 |
| Деталь: | HDD:Hitachi:40GB:Path:ROHS |
| Парткод: | B514 5990 |
| Деталь: | HDD bracket |
| Парткод: | B238 5882 |
| Деталь: | Rubber Cushion |
| Парткод: | AA16 1125 |
| Деталь: | Screw:M3x4.2 |
| Парткод: | AA14 3548 |
| Деталь: | Controller Board:AT-C1A |
| Парткод: | B231 5781 |
| Деталь: | Controller Board:AT-C1B |
| Парткод: | B238 5781 |
| Деталь: | Rail:Right |
| Парткод: | B622 5831 |
| Деталь: | Rail:Left |
| Парткод: | B622 5832 |
| Деталь: | Fan Motor - Mm42x10.5 DC5V |
| Парткод: | B237 5721 |
| Деталь: | Fan motor bracket |
| Парткод: | B238 5892 |
| Деталь: | Control Board Panel Grip |
| Парткод: | B238 5885 |
| Деталь: | Panel:SD-Card |
| Парткод: | B238 5894 |
| Деталь: | Interface Panel |
| Парткод: | B238 5887 |
| Деталь: | Control Board Panel |
| Парткод: | B238 5884 |
| Деталь: | Bracket:Control Board |
| Парткод: | B238 5880 |
| Деталь: | PCB:DDR-DIMM:512MB |
| Парткод: | G108 5020 |
| Деталь: | NVRAM - ZERO Counter |
| Парткод: | B230 9590 |
| Деталь: | SD-Card:AT-C1:P/S:Exp:Assy |
| Парткод: | B237 5617 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Screw:Unc:6-32 |
| Парткод: | 8 010 226 |
| Деталь: | Tapping Screw - 3x16 |
| Парткод: | 0451 3016N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Drawer:Intermediate Transfer:Assy |
| Парткод: | B223 6140 |
| Деталь: | Harness - Toner Supply |
| Парткод: | B238 5309 |
| Деталь: | Harness - High Voltage Line T TS |
| Парткод: | B238 5387 |
| Деталь: | Toner End Sensor |
| Парткод: | AW02 0185 |
| Деталь: | Pump Unit - BK |
| Парткод: | B223 3201 |
| Деталь: | Pump Unit - M |
| Парткод: | B223 3204 |
| Деталь: | Pump Unit - C |
| Парткод: | B223 3203 |
| Деталь: | Pump Unit - Y |
| Парткод: | B223 3202 |
| Деталь: | TUBE CLAMP |
| Парткод: | B223 3206 |
| Деталь: | Nozzle Assy |
| Парткод: | B223 3205 |
| Деталь: | Tube Clip |
| Парткод: | B223 3209 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Connector - 2P |
| Парткод: | 11 026 259 |
| Деталь: | Relay Connector - 2P |
| Парткод: | 11 026 245 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Transport Screw Shaft |
| Парткод: | B223 6473 |
| Деталь: | Bushing - Dia5 |
| Парткод: | B223 6476 |
| Деталь: | Gear - 21Z |
| Парткод: | B223 6472 |
| Деталь: | Transport Screw Bracket |
| Парткод: | B223 6471 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | B223 6464 |
| Деталь: | Gear - 20Z |
| Парткод: | B223 6463 |
| Деталь: | Pipe:Front:Assy |
| Парткод: | B223 6451 |
| Деталь: | Separation Plate - Upper Left |
| Парткод: | B223 1087 |
| Деталь: | Separation Plate - Upper Middle Lef |
| Парткод: | B223 1084 |
| Деталь: | Separation Plate - Upper Middle Rig |
| Парткод: | B223 1080 |
| Деталь: | Separation Plate - Upper Right |
| Парткод: | B223 1076 |
| Деталь: | Lever Bracket |
| Парткод: | B223 6467 |
| Деталь: | Frame:Machine or Copier:Front:Peen |
| Парткод: | B238 1110 |
| Деталь: | Supporting Plate:Grip:Right Front |
| Парткод: | B238 1115 |
| Деталь: | Imaging Unit Plate - Inner |
| Парткод: | B223 1898 |
| Деталь: | Imaging Unit Plate - Outer |
| Парткод: | B223 1899 |
| Деталь: | Bushing - 5x 10x2.5 |
| Парткод: | B223 6475 |
| Деталь: | GEAR - 29Z |
| Парткод: | B223 6474 |
| Деталь: | Cover - Left |
| Парткод: | B238 1385 |
| Деталь: | Imaging Unit Plate - Rear |
| Парткод: | B223 1897 |
| Деталь: | Imaging Unit Plate - Front |
| Парткод: | B223 1896 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - 3x16 |
| Парткод: | 0451 3016N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Thermistor:Fusing |
| Парткод: | AW10 0105 |
| Деталь: | Stay:Fusing:Upper |
| Парткод: | B238 4202 |
| Деталь: | Fusing Belt |
| Парткод: | B238 4070 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AE02 0156 |
| Деталь: | Hot Roller |
| Парткод: | AE01 0054 |
| Деталь: | BELT TENSION ROLLER |
| Парткод: | AE04 0064 |
| Деталь: | Bushing - 20x25 |
| Парткод: | AE03 2030 |
| Деталь: | Ball Bearing:Mm25xmm32x7 |
| Парткод: | AE03 0066 |
| Деталь: | Spring:Stripper Plate:Front |
| Парткод: | AA06 6667 |
| Деталь: | Stripper Plate:Coat |
| Парткод: | B238 4291 |
| Деталь: | Spring:Stripper Plate:Rear |
| Парткод: | AA06 6668 |
| Деталь: | Bushing - Belt Tension Roller |
| Парткод: | AE03 1045 |
| Деталь: | Compression Spring:Belt Tensioner |
| Парткод: | AA06 3952 |
| Деталь: | Heat Roller:Dia25:Coat |
| Парткод: | AE01 2030 |
| Деталь: | Gear:Idler:Z14xz23 |
| Парткод: | AB01 3890 |
| Деталь: | Gear:Idler:Drive |
| Парткод: | AB01 4278 |
| Деталь: | Gear:Hot Roller:Roller Clutch:Z22 |
| Парткод: | AB01 3722 |
| Деталь: | Ball Bearing:Dia12xdia21x7 |
| Парткод: | AE03 0065 |
| Деталь: | Ball Bearing:Dia17xdia26x5 |
| Парткод: | AE03 0068 |
| Деталь: | Screw:Polished Round/Spring:M3x10 |
| Парткод: | 0954 3010N |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Retaining Ring - M8 |
| Парткод: | 0727 0080E |
| Деталь: | Retaining Ring C - M12 |
| Парткод: | 0725 0120E |
| Деталь: | Retaining Ring C - M17 |
| Парткод: | 0725 0170E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Paper Tray Unit No.2 |
| Парткод: | B223 2900 |
| Деталь: | Link - Paper Size Sensor |
| Парткод: | B223 2910 |
| Деталь: | SPACER |
| Парткод: | B223 2911 |
| Деталь: | Decal - Paper Set Direction No.2 |
| Парткод: | B238 2523 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B223 2940 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3006 |
| Деталь: | Ground Plate - Paper Tray No.2 |
| Парткод: | B223 2919 |
| Деталь: | Cover - Paper Tray No.2 |
| Парткод: | B223 2946 |
| Деталь: | Paper Tray Grip |
| Парткод: | B223 2860 |
| Деталь: | Decal - Grip |
| Парткод: | B238 2527 |
| Деталь: | Lever - Release Inner |
| Парткод: | B223 2862 |
| Деталь: | SPRING |
| Парткод: | AA06 0900 |
| Деталь: | Release Shaft |
| Парткод: | B223 2863 |
| Деталь: | Grip Holder |
| Парткод: | B223 2861 |
| Деталь: | External Circlip - Mm8 |
| Парткод: | A222 2724 |
| Деталь: | Lever - Release Outer |
| Парткод: | B223 2864 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | END FENCE |
| Парткод: | B223 2912 |
| Деталь: | Front Side Fence |
| Парткод: | B223 2920 |
| Деталь: | Stopper Lever - Front |
| Парткод: | B223 2923 |
| Деталь: | Spring Plate - Release Lever |
| Парткод: | B004 2923 |
| Деталь: | Plate - Side Fence Right |
| Парткод: | B223 2935 |
| Деталь: | Plate - Side Fence |
| Парткод: | B223 2934 |
| Деталь: | Gear - 16Z |
| Парткод: | B223 2936 |
| Деталь: | Rise No.1 Shaft |
| Парткод: | B223 2865 |
| Деталь: | Rise Lever |
| Парткод: | B223 2918 |
| Деталь: | Rear Side Fence |
| Парткод: | B223 2930 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A267 2860 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Decal - Side Fence Rear |
| Парткод: | B223 2873 |
| Деталь: | Tension Spring:Side Fence:Rear |
| Парткод: | AA06 1003 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0450 4008N |
| Деталь: | Binding Self Tapping Screw:3x8 |
| Парткод: | 0453 3008N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Supporter - Left No.2 |
| Парткод: | B223 2710 |
| Деталь: | Supporter - Left No.1 |
| Парткод: | B223 2705 |
| Деталь: | Heat Sink:Heater:EU |
| Парткод: | B223 2703 |
| Деталь: | Bracket:Paper Feed Unit:Peen |
| Парткод: | B238 1056 |
| Деталь: | Duplex Link |
| Парткод: | B238 4669 |
| Деталь: | Positioning Cap - Short |
| Парткод: | B223 2714 |
| Деталь: | Supporter - Right |
| Парткод: | B223 2715 |
| Деталь: | CUSHION |
| Парткод: | AA16 1163 |
| Деталь: | Rubber Foot:H5 |
| Парткод: | B101 1097 |
| Деталь: | Rubber Foot Cover |
| Парткод: | B238 1066 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Cover:Connector:Heater:Imaging Unit |
| Парткод: | B238 1067 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 8 025 299 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Ring Separator |
| Парткод: | 8 050 097 |
| Деталь: | Electrode Plate:Fusing:Common |
| Парткод: | B238 4315 |
| Деталь: | Thermostat:190 c |
| Парткод: | AW11 0059 |
| Деталь: | Thermostat:177 c |
| Парткод: | AW11 0058 |
| Деталь: | Electrode Plate:Thermostat |
| Парткод: | B238 4313 |
| Деталь: | Thermostat Housing |
| Парткод: | B238 4123 |
| Деталь: | Gear:Idler:Fusing Unit |
| Парткод: | GB01 0007 |
| Деталь: | Gear:Idler:Z14 |
| Парткод: | AB01 3861 |
| Деталь: | THERMISTOR |
| Парткод: | AW10 0104 |
| Деталь: | Thermistor Bracket |
| Парткод: | B238 4111 |
| Деталь: | Thermostat Housing |
| Парткод: | B238 4134 |
| Деталь: | Thermostat - 146c/147c |
| Парткод: | AW11 0055 |
| Деталь: | Harness:Fusing Unit:TWN |
| Парткод: | B237 4307 |
| Деталь: | Harness:Fusing Unit:EU |
| Парткод: | B237 4305 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | B238 4271 |
| Деталь: | Electrode Plate:Fusing:Main |
| Парткод: | B238 4311 |
| Деталь: | Electrode Plate:Fusing:Sub |
| Парткод: | B238 4312 |
| Деталь: | Electrode Plate:Pressure |
| Парткод: | B238 4316 |
| Деталь: | Electrode Plate:Pressure:Thermostat |
| Парткод: | B238 4318 |
| Деталь: | Electrode Plate:Pressure:Common |
| Парткод: | B238 4319 |
| Деталь: | Electrode Plate:Thermostat:Connecti |
| Парткод: | B238 4314 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3870 |
| Деталь: | Gear:Idler:Z16 |
| Парткод: | GB01 0011 |
| Деталь: | Arm Screw |
| Парткод: | 58 942 540 |
| Деталь: | Screw:Polished Round/spring:M4x12 |
| Парткод: | 0954 4012N |
| Деталь: | Screw - M4X8 |
| Парткод: | 0954 4008N |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 8 046 123 |
| Деталь: | Screw:Polished Round/Spring:M3x10 |
| Парткод: | 0954 3010N |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Harness - IOB BICU |
| Парткод: | B238 5304 |
| Деталь: | Duct - Tube 1 |
| Парткод: | B238 1136 |
| Деталь: | Fan Motor - Mm60 DC24V |
| Парткод: | AX64 0170 |
| Деталь: | Duct - Tube 2 |
| Парткод: | B238 1137 |
| Деталь: | Mother Board Bracket |
| Парткод: | B238 5853 |
| Деталь: | GASKET |
| Парткод: | B238 5855 |
| Деталь: | Harness - Operation Panel |
| Парткод: | B238 5373 |
| Деталь: | Harness Sheet |
| Парткод: | B238 5856 |
| Деталь: | Application Rack Bracket |
| Парткод: | B238 1084 |
| Деталь: | Hinge Bracket - Upper |
| Парткод: | B238 5859 |
| Деталь: | PCB:BICU:AT-C1:Assy |
| Парткод: | B238 5100 |
| Деталь: | Harness - BICU Imaging Unit |
| Парткод: | B238 5328 |
| Деталь: | Scanner interface cable |
| Парткод: | B238 5345 |
| Деталь: | Base:Rack:Application:Peen |
| Парткод: | B238 5851 |
| Деталь: | Cover:Rack:Application:Assy |
| Парткод: | B238 5854 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11 050 508 |
| Деталь: | Clamp - LES-1017 |
| Парткод: | 11 050 521 |
| Деталь: | Edge Saddle - Les-1010 |
| Парткод: | 11 050 518 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | EEPROM:BR24L64-W |
| Парткод: | 14 076 362 |
| Деталь: | Ferrite Core:RFC-4 |
| Парткод: | 16 071 663 |
| Деталь: | DRIVE UNIT |
| Парткод: | B237 1041 |
| Деталь: | Brushless Motor DC24V8W |
| Парткод: | AX05 0249 |
| Деталь: | Brushless Motor DC24V24W |
| Парткод: | AX06 0310 |
| Деталь: | Brushless Motor DC24V40W |
| Парткод: | AX06 0311 |
| Деталь: | DC Motor 24V |
| Парткод: | B223 1199 |
| Деталь: | Brushless Motor:Drive:Paper Feed |
| Парткод: | GX06 0015 |
| Деталь: | Holder:Magnetic Clutch:Development |
| Парткод: | B238 1219 |
| Деталь: | Magnetic Spring Clutch - 0.98n.m |
| Парткод: | AB04 4006 |
| Деталь: | Development Drive Shaft |
| Парткод: | B238 1170 |
| Деталь: | Gear - 23Z |
| Парткод: | AB01 0367 |
| Деталь: | Gear - 45Z |
| Парткод: | AB01 0368 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Screw - M3X16 |
| Парткод: | 0360 3016N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Paper Tray Unit No.1 |
| Парткод: | B223 2850 |
| Деталь: | Screw:DIA6 |
| Парткод: | AA14 3843 |
| Деталь: | Slide Rail - Left |
| Парткод: | B223 2890 |
| Деталь: | Slide Rail Stopper - Left |
| Парткод: | B223 2894 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B223 2940 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3006 |
| Деталь: | Decal - Paper Set Direction No.1 |
| Парткод: | B237 2521 |
| Деталь: | Cover - Paper Tray No.1 |
| Парткод: | B223 2857 |
| Деталь: | Paper Tray Grip |
| Парткод: | B223 2860 |
| Деталь: | Decal - Grip |
| Парткод: | B238 2526 |
| Деталь: | Lever - Release Inner |
| Парткод: | B223 2862 |
| Деталь: | SPRING |
| Парткод: | AA06 0900 |
| Деталь: | Release Shaft |
| Парткод: | B223 2863 |
| Деталь: | Grip Holder |
| Парткод: | B223 2861 |
| Деталь: | External Circlip - Mm8 |
| Парткод: | A222 2724 |
| Деталь: | Lever - Release Outer |
| Парткод: | B223 2864 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | END FENCE |
| Парткод: | B223 2912 |
| Деталь: | Side Fence - Front |
| Парткод: | B223 2870 |
| Деталь: | Stopper Lever - Front |
| Парткод: | B223 2923 |
| Деталь: | Spring Plate - Release Lever |
| Парткод: | B004 2923 |
| Деталь: | Plate - Side Fence Right |
| Парткод: | B223 2935 |
| Деталь: | Plate - Side Fence |
| Парткод: | B223 2934 |
| Деталь: | Gear - 16Z |
| Парткод: | B223 2936 |
| Деталь: | Rise No.1 Shaft |
| Парткод: | B223 2865 |
| Деталь: | Rise Lever |
| Парткод: | B223 2918 |
| Деталь: | Side Fence - Rear |
| Парткод: | B223 2880 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A267 2860 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Decal - Side Fence Rear |
| Парткод: | B223 2873 |
| Деталь: | Tension Spring:Side Fence:Rear |
| Парткод: | AA06 1003 |
| Деталь: | GROUND PLATE |
| Парткод: | B223 2869 |
| Деталь: | Screw:Tp:M4 |
| Парткод: | AA14 3577 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0450 4008N |
| Деталь: | Binding Self Tapping Screw:3x8 |
| Парткод: | 0453 3008N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Fan Motor - DC24V |
| Парткод: | GX64 0020 |
| Деталь: | Fusing Duct - 1 |
| Парткод: | B238 1126 |
| Деталь: | Fusing Duct - 2 |
| Парткод: | B238 1127 |
| Деталь: | Duct - Drive 1 |
| Парткод: | B238 1121 |
| Деталь: | Duct - Drive 2 |
| Парткод: | B238 1122 |
| Деталь: | Harness - IOB Drum Motor |
| Парткод: | B238 5305 |
| Деталь: | PCB IOB |
| Парткод: | B238 5120 |
| Деталь: | Harness - Main |
| Парткод: | B238 5300 |
| Деталь: | Harness Clamp |
| Парткод: | B238 5842 |
| Деталь: | IOB Bracket |
| Парткод: | B238 5841 |
| Деталь: | Connector bracket |
| Парткод: | B223 1065 |
| Деталь: | Harness - IOB Duplex Unit |
| Парткод: | B238 5318 |
| Деталь: | Main Switch Bracket |
| Парткод: | B238 5827 |
| Деталь: | Harness - IOB Skew-motor |
| Парткод: | B238 5311 |
| Деталь: | Harness - IOB Paper Feed Unit |
| Парткод: | B238 5314 |
| Деталь: | Harness - Lift Motor |
| Парткод: | B238 5315 |
| Деталь: | Harness - IOB Bank |
| Парткод: | B238 5317 |
| Деталь: | Harness - Fusing |
| Парткод: | B238 5319 |
| Деталь: | Harness - IOB Power Source |
| Парткод: | B238 5322 |
| Деталь: | Harness - IOB PCU |
| Парткод: | B238 5307 |
| Деталь: | Harness - IOB Toner Supply |
| Парткод: | B238 5308 |
| Деталь: | Cover:Connector:Heater |
| Парткод: | B223 5849 |
| Деталь: | Bracket:Base:Connector |
| Парткод: | B223 5848 |
| Деталь: | Cover - Positioning Pin |
| Парткод: | B238 1089 |
| Деталь: | Main Switch Sheet |
| Парткод: | B238 5828 |
| Деталь: | Cover - Connector |
| Парткод: | B238 1088 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Switch - RS1A-AB11 |
| Парткод: | 12 042 704 |
| Деталь: | Harness Clamp - LWS 1316 |
| Парткод: | 11 050 489 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Connector - QR/P17-14S-B |
| Парткод: | 11 028 534 |
| Деталь: | Vertical Transport Roller |
| Парткод: | AF02 0646 |
| Деталь: | BUSHING - M4 |
| Парткод: | G060 2652 |
| Деталь: | Spring - 11n |
| Парткод: | B223 2676 |
| Деталь: | Guide Plate - Vertical Transport |
| Парткод: | B223 2675 |
| Деталь: | Sheet - Transport Sub-unit |
| Парткод: | B223 2677 |
| Деталь: | Roller:Driven - Dia16 |
| Парткод: | AF02 0622 |
| Деталь: | Driven Roller Bushing |
| Парткод: | AA08 0313 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3437 |
| Деталь: | GUIDE PLATE |
| Парткод: | B238 2761 |
| Деталь: | Duplex Guide Plate - Right Upper |
| Парткод: | B238 4643 |
| Деталь: | Entrance Sensor |
| Парткод: | B238 4645 |
| Деталь: | Set Sensor Lever |
| Парткод: | B238 4647 |
| Деталь: | Pressure Release Arm - Rear |
| Парткод: | B238 4683 |
| Деталь: | Arm Stopper Bracket |
| Парткод: | B238 4686 |
| Деталь: | TORSION SPRING |
| Парткод: | B238 4688 |
| Деталь: | STOPPER ARM |
| Парткод: | B238 4677 |
| Деталь: | TORSION SPRING |
| Парткод: | B238 4687 |
| Деталь: | Stopper Link |
| Парткод: | B238 4679 |
| Деталь: | Lever - Duplex |
| Парткод: | B238 4633 |
| Деталь: | Compression Spring - Lever Duplex |
| Парткод: | B238 4635 |
| Деталь: | Inner Cover:Duplex:Adhesion |
| Парткод: | B238 4646 |
| Деталь: | Pressure Release Arm - Front |
| Парткод: | B238 4682 |
| Деталь: | Decal:Warning (High Temperature):DU |
| Парткод: | B238 4649 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Exit Guide Plate - Lower |
| Парткод: | B223 4431 |
| Деталь: | Guide Roller |
| Парткод: | AF04 0571 |
| Деталь: | Roller - Dia16 |
| Парткод: | B223 4433 |
| Деталь: | PRESSURE SHAFT |
| Парткод: | B223 4432 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0156 |
| Деталь: | Compression Spring - Driven Roller |
| Парткод: | B238 4458 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0567 |
| Деталь: | Spring Plate - Exit Roller Outer |
| Парткод: | B238 4436 |
| Деталь: | Sensor bracket |
| Парткод: | B238 4454 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0127 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0566 |
| Деталь: | Spring Plate - Exit Roller |
| Парткод: | B223 4436 |
| Деталь: | Harness - Exit |
| Парткод: | B238 5390 |
| Деталь: | EXIT ROLLER |
| Парткод: | B238 4441 |
| Деталь: | Overflow Feeler |
| Парткод: | B238 4987 |
| Деталь: | Overflow Feeler Shaft |
| Парткод: | B238 4985 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Paper Feed Sensor Feeler |
| Парткод: | B238 4449 |
| Деталь: | Transport Roller |
| Парткод: | B238 4442 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Gear - 28Z |
| Парткод: | B238 4444 |
| Деталь: | Gear - 45Z |
| Парткод: | B238 4445 |
| Деталь: | Gear - 28Z |
| Парткод: | B238 4915 |
| Деталь: | Gear - 28Z |
| Парткод: | B238 4446 |
| Деталь: | SCREW |
| Парткод: | B238 4483 |
| Деталь: | Harness - Fusing Exit Sensor |
| Парткод: | B238 5389 |
| Деталь: | Reverse Guide Plate - Lower |
| Парткод: | B238 4922 |
| Деталь: | Reverse Guide Plate - Upper |
| Парткод: | B238 4912 |
| Деталь: | Reverse Roller |
| Парткод: | B238 4911 |
| Деталь: | Discharge Brush:Exit |
| Парткод: | B223 4491 |
| Деталь: | Gate Pawl |
| Парткод: | B238 4472 |
| Деталь: | Gate Pawl Lever |
| Парткод: | B238 4476 |
| Деталь: | Spring - Gate Pawl Lever |
| Парткод: | B238 4475 |
| Деталь: | Exit Guide Plate - Upper |
| Парткод: | B238 4443 |
| Деталь: | DC Solenoid Bracket |
| Парткод: | B238 4473 |
| Деталь: | Lever - DC Solenoid Gate Pawl |
| Парткод: | B238 4479 |
| Деталь: | Spring - DC Solenoid Gate Pawl |
| Парткод: | B238 4477 |
| Деталь: | DC Solenoid:24V:4.0n:Assy |
| Парткод: | B482 3817 |
| Деталь: | Buffer:Gate Pawl |
| Парткод: | B238 4438 |
| Деталь: | Guide:Exit Roller:Auxiliary |
| Парткод: | B238 4447 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Screw-m3x10 |
| Парткод: | 0353 0100N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Retaining Ring - M2.5 |
| Парткод: | 0720 0025E |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Screw - M3X4 |
| Парткод: | 0353 0040N |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Fusing Unit:NA:Maintenance |
| Парткод: | B237 4053 |
| Деталь: | Fusing Unit:EU:Maintenance |
| Парткод: | B237 4054 |
| Деталь: | Heater - 213V 700W/500W |
| Парткод: | AX44 0255 |
| Деталь: | Heater:107V:700W/500W |
| Парткод: | AX44 0265 |
| Деталь: | Heater - 213V 250W |
| Парткод: | AX43 0174 |
| Деталь: | Heater:107V:250W |
| Парткод: | AX43 0184 |
| Деталь: | Fusing Cover:Upper |
| Парткод: | B238 4331 |
| Деталь: | Decal:Warning (High Temperature):FU |
| Парткод: | B238 4335 |
| Деталь: | Sheet:B2:Lever:Face Front |
| Парткод: | B238 4285 |
| Деталь: | GUIDE PLATE:FUSING EXIT |
| Парткод: | B238 4281 |
| Деталь: | Spring:Fusing Exit:Pressure |
| Парткод: | AA06 0989 |
| Деталь: | Stay:Fusing:Right:Peen |
| Парткод: | B238 4211 |
| Деталь: | Front Bushing - Oil Supply Roller |
| Парткод: | AE03 1061 |
| Деталь: | Oil Supply Roller |
| Парткод: | AE04 0065 |
| Деталь: | Cleaning Roller - Oil Supply Roller |
| Парткод: | AE04 0066 |
| Деталь: | Compression Spring:Oil Supply Rolle |
| Парткод: | AA06 3953 |
| Деталь: | Bracket:Heater:Fusing:Rear |
| Парткод: | B238 4232 |
| Деталь: | Bracket:Frame:Rear:Peen |
| Парткод: | B238 4254 |
| Деталь: | Positioning Plate:Rear |
| Парткод: | B238 4257 |
| Деталь: | Bracket:Heater:Pressure:Rear |
| Парткод: | B238 4243 |
| Деталь: | Spring:Pressure:50n |
| Парткод: | AA06 0990 |
| Деталь: | Lever:Lock:Pressure |
| Парткод: | B238 4197 |
| Деталь: | Lever:Pressure:Rear:Peen |
| Парткод: | B238 4195 |
| Деталь: | Lever:Pressure Release:Rear |
| Парткод: | B238 4191 |
| Деталь: | End Ring:Spring:DIA4 |
| Парткод: | B238 4166 |
| Деталь: | Roller:Lever:Pressure |
| Парткод: | B238 4194 |
| Деталь: | Screw:Drawer |
| Парткод: | AA14 3792 |
| Деталь: | SCREW |
| Парткод: | B238 4483 |
| Деталь: | Lever:Pressure:Front:Peen |
| Парткод: | B238 4175 |
| Деталь: | Lever:Pressure Release:Front |
| Парткод: | B238 4171 |
| Деталь: | Bracket:Heater:Pressure:Front |
| Парткод: | B238 4241 |
| Деталь: | Bracket:Heater:Fusing:Front |
| Парткод: | B238 4231 |
| Деталь: | Bracket:Frame:Front |
| Парткод: | B238 4252 |
| Деталь: | Positioning Plate:Front |
| Парткод: | B238 4253 |
| Деталь: | Sheet:B2:Lever:Behind |
| Парткод: | B238 4286 |
| Деталь: | Rear Bushing - Oil Supply Roller |
| Парткод: | AE03 1062 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 8 046 123 |
| Деталь: | Screw - M4X8 |
| Парткод: | 0954 4008N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Bushing:4x8 |
| Парткод: | 7 330 408 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Carriage Unit No.2 |
| Парткод: | B238 1688 |
| Деталь: | Mirror No.2 |
| Парткод: | AC03 0162 |
| Деталь: | Spring Plate - 2nd Mirror |
| Парткод: | G404 2810 |
| Деталь: | Pulley Holder |
| Парткод: | G570 2833 |
| Деталь: | Pulley - High Voltage Supply Cord |
| Парткод: | G570 2834 |
| Деталь: | Guide - High Voltage Supply Cord |
| Парткод: | G570 2832 |
| Деталь: | Idler pulley |
| Парткод: | B238 1806 |
| Деталь: | Harness - STM |
| Парткод: | B238 5371 |
| Деталь: | Stepper Motor DC3.9V |
| Парткод: | B238 1715 |
| Деталь: | Stepper Motor Bracket |
| Парткод: | B238 1788 |
| Деталь: | Tension Spring:Tension:14720mn |
| Парткод: | AA06 0979 |
| Деталь: | Ground Plate - Stepper Motor |
| Парткод: | B238 1762 |
| Деталь: | Timing Belt - 157ST1.5-4.0 |
| Парткод: | B238 1792 |
| Деталь: | Drive Were |
| Парткод: | B238 1787 |
| Деталь: | Bracket:Tension |
| Парткод: | B180 1704 |
| Деталь: | Tension Spring:Tension:11300mn |
| Парткод: | AA06 0980 |
| Деталь: | Scanner Drive Shaft |
| Парткод: | B238 1786 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2144 |
| Деталь: | Pulley:Drive Were:Rear:Sub-assy |
| Парткод: | B180 1812 |
| Деталь: | Timing Pulley 73 |
| Парткод: | G570 1133 |
| Деталь: | Pulley:Drive Were:Front:Sub-assy |
| Парткод: | B180 1810 |
| Деталь: | Heater:Option:230V:9W |
| Парткод: | B229 1688 |
| Деталь: | 1st Slide Rail |
| Парткод: | A193 1816 |
| Деталь: | Slide Rail:No.2 |
| Парткод: | B180 1734 |
| Деталь: | Bushing Spacer |
| Парткод: | B238 1793 |
| Деталь: | Hall Plug |
| Парткод: | B238 1796 |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 8 025 299 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Clamp - SB-2712 |
| Парткод: | 11 050 621 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Used Toner Sensor Bracket |
| Парткод: | B223 6502 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Used Toner Sensor Feeler |
| Парткод: | B223 6503 |
| Деталь: | Harness - Used Toner Sensor |
| Парткод: | B238 5313 |
| Деталь: | Fan Motor - Mm60 DC24V |
| Парткод: | B223 1332 |
| Деталь: | Fan Motor Bracket - Rear |
| Парткод: | B238 1132 |
| Деталь: | Harness Shadeing Plate |
| Парткод: | B238 1138 |
| Деталь: | Collection Bottle Rail |
| Парткод: | B223 6496 |
| Деталь: | Fan Motor Bracket - Front |
| Парткод: | B238 1131 |
| Деталь: | Bracket - Main Switch Handle |
| Парткод: | B238 5821 |
| Деталь: | Slide Switch Cover |
| Парткод: | B238 5824 |
| Деталь: | Power Source Switch Link |
| Парткод: | B238 5825 |
| Деталь: | Cleaning Unit Rail |
| Парткод: | B223 6198 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - M4x10 |
| Парткод: | 8 025 303 |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Brushless Motor:Drive:Paper Feed |
| Парткод: | GX06 0015 |
| Деталь: | Fusing Exit Unit Bracket |
| Парткод: | B238 1213 |
| Деталь: | Gear - 23Z/91Z |
| Парткод: | AB01 7716 |
| Деталь: | Gear - 120Z/23T |
| Парткод: | AB01 7714 |
| Деталь: | Timing Belt - 50S3M258 |
| Парткод: | AA04 3317 |
| Деталь: | Pulley - 26T |
| Парткод: | AB03 3100 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 7715 |
| Деталь: | Arm Guide Plate |
| Парткод: | B238 4754 |
| Деталь: | Stepper Motor Bracket |
| Парткод: | B238 4750 |
| Деталь: | Gear - 22Z/45T |
| Парткод: | B238 4753 |
| Деталь: | Timing Belt - B40S2M166 |
| Парткод: | B238 4755 |
| Деталь: | Stepper Motor:Assy |
| Парткод: | B238 4720 |
| Деталь: | Cushion - Stepper Motor |
| Парткод: | A232 4666 |
| Деталь: | Stepper Motor DC5.06V |
| Парткод: | B223 1350 |
| Деталь: | Drive Unit Bracket |
| Парткод: | B238 1220 |
| Деталь: | Timing Pulley - 27Z/40T |
| Парткод: | AB03 0744 |
| Деталь: | Timing Belt - B40S2M118 |
| Парткод: | AA04 3601 |
| Деталь: | Cover:Bracket:Fusing Exit Section |
| Парткод: | B238 1234 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Clamp:EDS-0704L-V0 |
| Парткод: | 11 050 612 |
| Деталь: | Positioning Guide - Front |
| Парткод: | B223 6311 |
| Деталь: | CUSHION |
| Парткод: | B223 6315 |
| Деталь: | Positioning Guide - Rear |
| Парткод: | B223 6312 |
| Деталь: | TENSION SPRING |
| Парткод: | B238 2676 |
| Деталь: | Registration Roller - Driven |
| Парткод: | B238 2661 |
| Деталь: | Registration Roller Bushing |
| Парткод: | B238 2675 |
| Деталь: | Gear - 18Z |
| Парткод: | B238 2657 |
| Деталь: | Registration Roller - Drive |
| Парткод: | B238 2652 |
| Деталь: | Registration Roller Knob |
| Парткод: | B223 2558 |
| Деталь: | Gear - 16Z |
| Парткод: | B238 2655 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Gear - 30Z |
| Парткод: | B238 2656 |
| Деталь: | Cleaner Bracket |
| Парткод: | B238 2670 |
| Деталь: | STAY |
| Парткод: | B238 2621 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Harness - Registration Sensor |
| Парткод: | B238 5391 |
| Деталь: | Registration Guide Plate - Right |
| Парткод: | B238 2640 |
| Деталь: | Registration Guide Plate - Left |
| Парткод: | B238 2612 |
| Деталь: | GUIDE PLATE |
| Парткод: | B223 2835 |
| Деталь: | Guide Plate No.2 |
| Парткод: | B223 2840 |
| Деталь: | Cover - Remove Paper Dust |
| Парткод: | B238 2622 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Clamp - RFC-14V0 |
| Парткод: | 11 050 643 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw:3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | Exit Guide Plate |
| Парткод: | B238 4637 |
| Деталь: | Supporting Plate:Duplex |
| Парткод: | B238 4628 |
| Деталь: | Harness - Ground Wire |
| Парткод: | B238 5392 |
| Деталь: | Timing Belt - 30S2M340 |
| Парткод: | B238 4716 |
| Деталь: | Timing Belt - 30S2M360 |
| Парткод: | B238 4715 |
| Деталь: | Pulley - 28T |
| Парткод: | B238 4704 |
| Деталь: | Pulley - 40T |
| Парткод: | B238 4706 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Exit Sensor Case |
| Парткод: | B238 4653 |
| Деталь: | Transport Roller - Duplex:Exit |
| Парткод: | B238 4713 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Exit Sensor Bracket |
| Парткод: | B238 4654 |
| Деталь: | Transport Roller - Middle |
| Парткод: | B238 4712 |
| Деталь: | Transport Roller - Entrance |
| Парткод: | B238 4711 |
| Деталь: | Harness - Duplex Unit |
| Парткод: | B238 5376 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Entrance Sensor Bracket |
| Парткод: | B238 4650 |
| Деталь: | Gear Pulley - 25Z/25T |
| Парткод: | B238 4703 |
| Деталь: | Timing Belt - 30S2M206 |
| Парткод: | B238 4714 |
| Деталь: | Timing Pulley - 24T |
| Парткод: | C408 1119 |
| Деталь: | Coupling Arm |
| Парткод: | B238 4700 |
| Деталь: | Pulley - 40T |
| Парткод: | B238 4710 |
| Деталь: | SPACER |
| Парткод: | B238 4708 |
| Деталь: | Gear - 16Z |
| Парткод: | B238 4707 |
| Деталь: | Gear - Z30 |
| Парткод: | G569 2822 |
| Деталь: | Harness - Ground Wire |
| Парткод: | B238 5377 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Cover - Duplex |
| Парткод: | B238 4610 |
| Деталь: | TENSION SPRING:ARM:COUPLING |
| Парткод: | B238 4717 |
| Деталь: | Pulley - 40T |
| Парткод: | B238 4705 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Parallel Pin - 3x12 |
| Парткод: | 0633 0120G |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | CLAMP |
| Парткод: | 11 050 534 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Philips Pan Head Screw - M4x6 |
| Парткод: | 8 010 149 |
| Деталь: | Stepper Motor DC24V |
| Парткод: | B223 1188 |
| Деталь: | Cushion:Stepper Motor |
| Парткод: | AA16 1164 |
| Деталь: | Magnetic Clutch Bracket |
| Парткод: | B223 1187 |
| Деталь: | Magnetic Clutch - 32Z |
| Парткод: | AX20 0289 |
| Деталь: | BUSHING - 6MM |
| Парткод: | GA08 0002 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Harness Guide Bracket |
| Парткод: | B238 1228 |
| Деталь: | Paper Feed Unit Bracket |
| Парткод: | B238 1211 |
| Деталь: | Gear - 38Z |
| Парткод: | AB01 1258 |
| Деталь: | TIMING BELT - 40S3M144 |
| Парткод: | AA04 3318 |
| Деталь: | Timing Pulley - 28Z/30T |
| Парткод: | AB03 0781 |
| Деталь: | Drive Unit Drum Stay |
| Парткод: | B238 1206 |
| Деталь: | Gear - 33Z/44Z |
| Парткод: | AB01 7699 |
| Деталь: | Gear - 32Z |
| Парткод: | AB01 1259 |
| Деталь: | Drive Joint |
| Парткод: | B223 1186 |
| Деталь: | Feed Drive Shaft |
| Парткод: | B223 1189 |
| Деталь: | Grip Shaft |
| Парткод: | B223 1183 |
| Деталь: | Temperature & Humidity Sensor |
| Парткод: | AW14 0012 |
| Деталь: | Rubber Foot Cover |
| Парткод: | B238 1066 |
| Деталь: | Fusing Unit Guide Plate - Rear |
| Парткод: | B238 1063 |
| Деталь: | Left Fusing Lock Lever |
| Парткод: | G052 4697 |
| Деталь: | Tapping Screw - 4x10 |
| Парткод: | 0434 0100N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Clamp:EDS-0704L-V0 |
| Парткод: | 11 050 612 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 0451 4008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | DC Motor 24V |
| Парткод: | B223 1199 |
| Деталь: | HOLDER |
| Парткод: | B238 1223 |
| Деталь: | CAM |
| Парткод: | B238 1226 |
| Деталь: | SHAFT |
| Парткод: | B238 1225 |
| Деталь: | Tray Cover - Right |
| Парткод: | B238 2541 |
| Деталь: | DC Motor 24V |
| Парткод: | AX04 0154 |
| Деталь: | Rear Pipe Assy |
| Парткод: | B223 6481 |
| Деталь: | DRIVE UNIT |
| Парткод: | B238 1215 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0722 |
| Деталь: | Pulley - 34T |
| Парткод: | AB03 0783 |
| Деталь: | Timing Belt - S2M460 |
| Парткод: | AA04 3583 |
| Деталь: | Tray Cover - Middle |
| Парткод: | B238 2544 |
| Деталь: | Paper Tray Stopper Assy |
| Парткод: | B223 2730 |
| Деталь: | COVER |
| Парткод: | B223 2722 |
| Деталь: | Bracket:Push Switch |
| Парткод: | B223 2721 |
| Деталь: | Push Switch:Paper Size Sensor |
| Парткод: | AW50 0038 |
| Деталь: | Cover - Tray Left |
| Парткод: | B238 2543 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Set Sensor Bracket |
| Парткод: | B223 6507 |
| Деталь: | Harness - Paper Volume Sensor |
| Парткод: | B238 5325 |
| Деталь: | Pulley:Idler:Fusing |
| Парткод: | AB03 0551 |
| Деталь: | Guide:Connector:Heater:Imaging Unit |
| Парткод: | B238 1143 |
| Деталь: | Cover - Separation Plate |
| Парткод: | B238 1229 |
| Деталь: | Bracket:Connector:Heater:Imaging Un |
| Парткод: | B238 1142 |
| Деталь: | Tapping Screw - M3x30 |
| Парткод: | 8 025 304 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Tapping Screw:3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Hexagonal Head Bolt W/Washer:M3x6 |
| Парткод: | 8 010 231 |
| Деталь: | Tapping Screw:3x10 |
| Парткод: | 0451 3010N |
| Деталь: | Transfer/separation Unit:At:Assy |
| Парткод: | B238 6260 |
| Деталь: | Transfer Roller Case |
| Парткод: | B223 6281 |
| Деталь: | TERMINAL |
| Парткод: | B223 6289 |
| Деталь: | Transfer Roller Terminal |
| Парткод: | B223 6285 |
| Деталь: | TAB |
| Парткод: | B223 6287 |
| Деталь: | Harness - Second Transfer Unit |
| Парткод: | B223 4561 |
| Деталь: | Power Pack D |
| Парткод: | AZ30 0056 |
| Деталь: | Contact Point Bracket |
| Парткод: | B238 4658 |
| Деталь: | Lever Bracket - Middle |
| Парткод: | B223 6320 |
| Деталь: | Release Lever |
| Парткод: | B223 6306 |
| Деталь: | Lever Shaft - Front |
| Парткод: | B223 6322 |
| Деталь: | Cover - Entrance Sensor |
| Парткод: | B238 4739 |
| Деталь: | Entrance Sensor Bracket |
| Парткод: | B238 4733 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0118 |
| Деталь: | Guide Plate - Left Upper |
| Парткод: | B238 4664 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B238 4732 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B238 4731 |
| Деталь: | Transport Driven Roller - Middle |
| Парткод: | G060 2641 |
| Деталь: | GROUND PLATE |
| Парткод: | B238 4738 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B238 4735 |
| Деталь: | Cover - Harness |
| Парткод: | B238 4740 |
| Деталь: | Duplex Guide Plate |
| Парткод: | B238 4728 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 2306 |
| Деталь: | Bushing - 5mm |
| Парткод: | AA08 0312 |
| Деталь: | Driven Transport Roller |
| Парткод: | AF02 2137 |
| Деталь: | Driven Roller Bushing |
| Парткод: | AA08 0313 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2145 |
| Деталь: | Spring Cap |
| Парткод: | B223 6319 |
| Деталь: | Transfer Spring |
| Парткод: | B223 6308 |
| Деталь: | Spring Anchor |
| Парткод: | B223 6321 |
| Деталь: | Decal - Grip (Z) |
| Парткод: | B238 4729 |
| Деталь: | Lever Shaft - Rear |
| Парткод: | B223 6323 |
| Деталь: | Ground Wire - Power Pack |
| Парткод: | B223 6317 |
| Деталь: | Harness - Ground Wire |
| Парткод: | B238 5393 |
| Деталь: | Drum Stay - Rear |
| Парткод: | B223 6290 |
| Деталь: | Compression Spring - Earth Hvpp |
| Парткод: | B238 4736 |
| Деталь: | GUIDE PLATE |
| Парткод: | B238 4737 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Clamp:LES-0505 |
| Парткод: | 11 050 551 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Decal - Paper Size |
| Парткод: | B238 2524 |
| Деталь: | Cap - Left |
| Парткод: | B238 1382 |
| Деталь: | Filter:Image Forming MD |
| Парткод: | B223 1348 |
| Деталь: | Cover - Left DOM |
| Парткод: | B238 1384 |
| Деталь: | Cover - Left EU |
| Парткод: | B237 1384 |
| Деталь: | Cover - Main Switch |
| Парткод: | B223 1255 |
| Деталь: | Collection Bottlecover - Front |
| Парткод: | B223 1254 |
| Деталь: | MAGNET CATCH |
| Парткод: | AA02 1030 |
| Деталь: | Inner Cover - Left |
| Парткод: | B223 1242 |
| Деталь: | Cover - Front |
| Парткод: | B223 1251 |
| Деталь: | GUIDE PLATE |
| Парткод: | B238 1390 |
| Деталь: | Sheet - Misfeed Removalt |
| Парткод: | B238 1365 |
| Деталь: | MAGNET CATCH |
| Парткод: | B024 1264 |
| Деталь: | Hinge - Front Cover |
| Парткод: | G020 1332 |
| Деталь: | Cover - Right Front Lower DOM |
| Парткод: | B238 1375 |
| Деталь: | Cover - Right Front Lower EU |
| Парткод: | B237 1375 |
| Деталь: | Cover - Right Rear |
| Парткод: | B238 1371 |
| Деталь: | Cover - Right Rear EU |
| Парткод: | B237 1371 |
| Деталь: | Cap - Louver Mm80 |
| Парткод: | B238 1373 |
| Деталь: | Cap - Rear |
| Парткод: | B238 1396 |
| Деталь: | Cover - Rear DOM |
| Парткод: | B238 1393 |
| Деталь: | Cover - Rear EU |
| Парткод: | B237 1393 |
| Деталь: | Screw:M3 |
| Парткод: | AA14 3578 |
| Деталь: | Cover - Right |
| Парткод: | B238 1380 |
| Деталь: | Cover - Right Base EU |
| Парткод: | B237 1380 |
| Деталь: | Decal - Main Switch EU OP |
| Парткод: | B237 1355 |
| Деталь: | Cleaner:Shield Glass:Assy |
| Парткод: | B223 1279 |
| Деталь: | Sheet:Emblem:AT-C1A:RIC |
| Парткод: | B230 6932 |
| Деталь: | Sheet:Emblem:AT-C1A:SVN |
| Парткод: | B230 6933 |
| Деталь: | Sheet:Emblem:AT-C1A:GES |
| Парткод: | B230 6934 |
| Деталь: | Sheet:Emblem:AT-C1A:LAN |
| Парткод: | B230 6935 |
| Деталь: | Sheet:Emblem:AT-C1A:LAN |
| Парткод: | B230 6937 |
| Деталь: | Sheet:Emblem:AT-C1A:NSA |
| Парткод: | B230 6939 |
| Деталь: | Sheet:Emblem:AT-C1A:REX |
| Парткод: | B230 6940 |
| Деталь: | Sheet:Emblem:AT-C1A:GES |
| Парткод: | B230 6941 |
| Деталь: | Sheet:Emblem:AT-C1B:RIC |
| Парткод: | B237 6931 |
| Деталь: | Sheet:Emblem:AT-C1B:SVN |
| Парткод: | B237 6932 |
| Деталь: | Sheet:Emblem:AT-C1B:GES |
| Парткод: | B237 6933 |
| Деталь: | Sheet:Emblem:AT-C1B:LAN |
| Парткод: | B237 6934 |
| Деталь: | Sheet:Emblem:AT-C1B:LAN |
| Парткод: | B237 6936 |
| Деталь: | Sheet:Emblem:AT-C1B:NSA |
| Парткод: | B237 6938 |
| Деталь: | Sheet:Emblem:At-C1B:REX |
| Парткод: | B237 6939 |
| Деталь: | Sheet:Emblem:AT-C1B:GES |
| Парткод: | B237 6940 |
| Деталь: | Emblem Cover |
| Парткод: | B223 1253 |
| Деталь: | Decal:Color:Mfp |
| Парткод: | AA00 0239 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Toner Supply Drive Unit |
| Парткод: | B223 3400 |
| Деталь: | PCB RFID |
| Парткод: | B238 5050 |
| Деталь: | Rfid Ground Plate |
| Парткод: | B223 3470 |
| Деталь: | Stepper Motor DC24V |
| Парткод: | AX05 0265 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Gear:Toner Bottle:DRIVE |
| Парткод: | B223 3463 |
| Деталь: | Spring:Drive Unit:Toner Bottle |
| Парткод: | B223 3428 |
| Деталь: | Magnetic Clutch - 0.25n.m YCM |
| Парткод: | B223 3457 |
| Деталь: | Pulley:Toner Bottle:CM |
| Парткод: | B223 3462 |
| Деталь: | Pulley:Toner Bottle:YC |
| Парткод: | B223 3461 |
| Деталь: | Timing Belt:Toner Bottle |
| Парткод: | B223 3441 |
| Деталь: | Shaft:Drive:Drive Unit:CM |
| Парткод: | B223 3426 |
| Деталь: | Gear:Magnetic Clutch:Y |
| Парткод: | B223 3464 |
| Деталь: | Shaft:Drive:Drive Unit:BKY |
| Парткод: | B223 3424 |
| Деталь: | Magnetic Clutch - 0.25n.m BK |
| Парткод: | B223 3455 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 8 025 305 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | PAPER FEED UNIT |
| Парткод: | B238 2520 |
| Деталь: | Paper End Feeler |
| Парткод: | B223 2767 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Harness - Paper Feed Unit |
| Парткод: | B238 5375 |
| Деталь: | Bracket:Sensor |
| Парткод: | B082 2781 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0122 |
| Деталь: | Supporting Plate |
| Парткод: | B238 2576 |
| Деталь: | STAY |
| Парткод: | B223 2776 |
| Деталь: | Transport Roller |
| Парткод: | B238 2569 |
| Деталь: | Paper Feed Roller:Separate |
| Парткод: | AF03 2090 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2143 |
| Деталь: | Ground Plate - Front |
| Парткод: | B223 2786 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF03 0090 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | Feed guide |
| Парткод: | B223 2829 |
| Деталь: | Paper Feed Roller:Feed |
| Парткод: | AF03 1090 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1252 |
| Деталь: | Gear - Roller Clutch |
| Парткод: | AB01 1218 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Ground Plate - Feed |
| Парткод: | B223 2765 |
| Деталь: | Pickup Arm |
| Парткод: | B223 2761 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0691 |
| Деталь: | Lever - Feed |
| Парткод: | G065 2767 |
| Деталь: | Gear-24z |
| Парткод: | B223 2764 |
| Деталь: | Feed Shaft |
| Парткод: | B223 2762 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Release Lever |
| Парткод: | G065 2776 |
| Деталь: | Spring - Release |
| Парткод: | AA06 2259 |
| Деталь: | LINK LEVER |
| Парткод: | G065 2775 |
| Деталь: | Gear - 22Z |
| Парткод: | B223 2819 |
| Деталь: | TORQUE LIMITER |
| Парткод: | B004 2783 |
| Деталь: | Separate Drive Shaft |
| Парткод: | B223 2815 |
| Деталь: | Gear:Separate:Drive |
| Парткод: | AB01 0156 |
| Деталь: | Gear:Separate:Driven |
| Парткод: | AB01 0157 |
| Деталь: | PRESSURE LEVER |
| Парткод: | G065 2774 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0693 |
| Деталь: | Separate Driven Shaft |
| Парткод: | B223 2810 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Carriage Unit No.1 |
| Парткод: | B180 1816 |
| Деталь: | Xenon Lamp - DIA10 |
| Парткод: | B238 1820 |
| Деталь: | Wire Clamp |
| Парткод: | A193 1766 |
| Деталь: | Clamp - Rear Wire |
| Парткод: | A193 1769 |
| Деталь: | Original Sensor - 66mm |
| Парткод: | AW01 0133 |
| Деталь: | 1st Mirror |
| Парткод: | AC03 0142 |
| Деталь: | 1st Mirror Holder |
| Парткод: | A193 1767 |
| Деталь: | Inner Cover - Scanner |
| Парткод: | B238 1823 |
| Деталь: | Original Sensor - 48mm |
| Парткод: | AW01 0134 |
| Деталь: | Original Sensor Bracket |
| Парткод: | B238 1827 |
| Деталь: | Lens:Holder:Assy |
| Парткод: | B238 1703 |
| Деталь: | Stabilizer |
| Парткод: | B238 1821 |
| Деталь: | Inner Cover - Sensor |
| Парткод: | B238 1753 |
| Деталь: | Harness - SBU |
| Парткод: | B238 5368 |
| Деталь: | Scanner interface cable |
| Парткод: | B238 5345 |
| Деталь: | Harness - APS |
| Парткод: | B238 5367 |
| Деталь: | SBU Ground Plate |
| Парткод: | B238 5344 |
| Деталь: | Ground Plate - Carriage |
| Парткод: | B238 1812 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 8 025 299 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Clamp - JCC-1R |
| Парткод: | 11 050 622 |
| Деталь: | Toner Cartridge Unit |
| Парткод: | B223 3305 |
| Деталь: | Fusing Duct - Left |
| Парткод: | B238 1123 |
| Деталь: | Toner Cartridge Guide |
| Парткод: | B223 3328 |
| Деталь: | Rail:Right:Intermediate Transfer |
| Парткод: | B223 6146 |
| Деталь: | Rail:Left:Intermediate Transfer |
| Парткод: | B223 6145 |
| Деталь: | LENS COVER |
| Парткод: | B238 4366 |
| Деталь: | Thermopile |
| Парткод: | AW10 0106 |
| Деталь: | Lens Holder |
| Парткод: | B238 4365 |
| Деталь: | Right Door Stopper |
| Парткод: | B039 1073 |
| Деталь: | Sensor bracket |
| Парткод: | B238 4367 |
| Деталь: | Harness - Fusing |
| Парткод: | B238 5319 |
| Деталь: | Gear - 18Z/50Z |
| Парткод: | B238 4932 |
| Деталь: | Support Bracket |
| Парткод: | B238 1222 |
| Деталь: | Screw - M3X5 |
| Парткод: | AA14 3555 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Tapping Screw:3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 8 046 123 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Inner Cover - Upper Left DOM |
| Парткод: | B238 1398 |
| Деталь: | Inner Cover - Upper Left EU |
| Парткод: | B237 1398 |
| Деталь: | Decal:Colored Display:BK:Inner Cover |
| Парткод: | B238 3364 |
| Деталь: | Decal:Colored Display:Y:Inner Cover |
| Парткод: | B238 3365 |
| Деталь: | Decal:Colored Display:C:Inner Cover |
| Парткод: | B238 3366 |
| Деталь: | Decal:Colored Display:M:Inner Cover |
| Парткод: | B238 3367 |
| Деталь: | Decal - Cleaning |
| Парткод: | B238 1368 |
| Деталь: | Inner Cover - Middle |
| Парткод: | B223 1244 |
| Деталь: | Cover - Front Right DOM |
| Парткод: | B238 1397 |
| Деталь: | Cover - Front Right EU |
| Парткод: | B237 1397 |
| Деталь: | Cover - Right Front Upper DOM |
| Парткод: | B238 1378 |
| Деталь: | Cover - Right Front Upper EU |
| Парткод: | B237 1378 |
| Деталь: | Decal - Misfeed Removal B1 |
| Парткод: | B238 1362 |
| Деталь: | Inner Cover - Upper Right |
| Парткод: | B238 1356 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 1012 |
| Деталь: | Case - Remove Paper Dust |
| Парткод: | B238 2615 |
| Деталь: | Ball Bearing Plate |
| Парткод: | B223 1315 |
| Деталь: | Hinge - Cover Drum Stay |
| Парткод: | B223 1123 |
| Деталь: | Drum Stay |
| Парткод: | B223 1306 |
| Деталь: | WIRE |
| Парткод: | B223 1319 |
| Деталь: | Drum Stay PCU Assy |
| Парткод: | B223 1300 |
| Деталь: | SPRING |
| Парткод: | B223 1318 |
| Деталь: | Drum Stay Lever |
| Парткод: | B223 1303 |
| Деталь: | Ball Bearing Clip |
| Парткод: | B223 1316 |
| Деталь: | SCREW |
| Парткод: | B223 1317 |
| Деталь: | Stopper:Lever:Drum Stay |
| Парткод: | B223 1304 |
| Деталь: | Decal - Shielding Plate Y |
| Парткод: | GA00 3030 |
| Деталь: | Decal - Shielding Plate C |
| Парткод: | GA00 3032 |
| Деталь: | Decal - Shielding Plate M |
| Парткод: | GA00 3031 |
| Деталь: | Decal - Shielding Plate K |
| Парткод: | GA00 3033 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0451 3012N |
| Деталь: | Laser Optics Housing Unit |
| Парткод: | B238 1854 |
| Деталь: | Cover - Polygon Motor |
| Парткод: | B223 1882 |
| Деталь: | Harness - Polygon Mirror Motor |
| Парткод: | B238 5361 |
| Деталь: | Polygon Mirror Motor DC24V |
| Парткод: | AX06 0318 |
| Деталь: | SCREW |
| Парткод: | B223 1907 |
| Деталь: | SHUTTER ASSY |
| Парткод: | B223 1885 |
| Деталь: | Cover - Upper |
| Парткод: | B223 1881 |
| Деталь: | Screw:Link:Shutter |
| Парткод: | B223 1988 |
| Деталь: | Link:Shutter:1 |
| Парткод: | B223 1908 |
| Деталь: | Torsion Spring:Link:1 |
| Парткод: | B223 1913 |
| Деталь: | Link:Shutter:2 |
| Парткод: | B223 1909 |
| Деталь: | Torsion Spring:Link:2 |
| Парткод: | B223 1914 |
| Деталь: | LOUVER |
| Парткод: | B223 1903 |
| Деталь: | Plate Nut:Link |
| Парткод: | B223 1989 |
| Деталь: | Harness - LDB |
| Парткод: | B238 5363 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Binding Self-tapping Screw:3x10 |
| Парткод: | 0452 3010N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Guide Plate - Upper |
| Парткод: | B238 2731 |
| Деталь: | Cam - Manual Feed |
| Парткод: | B238 2712 |
| Деталь: | Roller - Manual Feed |
| Парткод: | B238 2726 |
| Деталь: | Paper Feed Roller - Mm30 |
| Парткод: | AF03 1068 |
| Деталь: | Shaft - Manual Feed |
| Парткод: | AA14 0868 |
| Деталь: | Friction pad |
| Парткод: | B238 2727 |
| Деталь: | Compression Spring:2n |
| Парткод: | GA06 3063 |
| Деталь: | Manual Feed Guide Plate - Lower |
| Парткод: | B238 2715 |
| Деталь: | Bushing - 6x10x9mm |
| Парткод: | AA08 2058 |
| Деталь: | Disc - Manual Feed |
| Парткод: | B238 2713 |
| Деталь: | Tension Spring - Disc Manual Feed |
| Парткод: | AA06 0993 |
| Деталь: | DC Solenoid Cover |
| Парткод: | B238 2718 |
| Деталь: | DC Solenoi 24V 9.6W |
| Парткод: | AX11 0123 |
| Деталь: | Holder - Paper End Sensor |
| Парткод: | B238 2743 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | B238 2742 |
| Деталь: | Feeler Spring - Paper End Sensor |
| Парткод: | AA06 6367 |
| Деталь: | Compression Spring - Manual Feed |
| Парткод: | AA06 3436 |
| Деталь: | Harness - Manual Feed Unit |
| Парткод: | B238 5378 |
| Деталь: | Manual Feed Cover - Lower |
| Парткод: | B238 2724 |
| Деталь: | Supporting Plate |
| Парткод: | B238 2722 |
| Деталь: | GROUND PLATE |
| Парткод: | B238 2723 |
| Деталь: | Manual Feed Guide Assy |
| Парткод: | B238 2720 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 52 152 713 |
| Деталь: | PIN |
| Парткод: | B238 2719 |
| Деталь: | Roller - Tray Bottom Plate |
| Парткод: | B238 2725 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Manual Feed Unit:Assy |
| Парткод: | B238 2710 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2075 |
| Деталь: | Gear - 30Z |
| Парткод: | B238 2711 |
| Деталь: | SCREW:M3:BLACK |
| Парткод: | AA14 3537 |
| Деталь: | Arm:Manual Feed Table |
| Парткод: | B238 2744 |
| Деталь: | Decal - Scale |
| Парткод: | B238 2751 |
| Деталь: | Front Side Fence |
| Парткод: | B039 2631 |
| Деталь: | Rear Side Fence |
| Парткод: | B039 2632 |
| Деталь: | Decal - Side Fence |
| Парткод: | B238 2753 |
| Деталь: | MANUAL FEED TABLE |
| Парткод: | B238 2741 |
| Деталь: | Decal - Paper Set Direction |
| Парткод: | B237 2752 |
| Деталь: | Harness - Manual Feed Table |
| Парткод: | B238 5379 |
| Деталь: | Paper size sensor |
| Парткод: | AW50 0031 |
| Деталь: | Rack - Rear Side Fence |
| Парткод: | B039 2638 |
| Деталь: | SIDE FENCE GEAR |
| Парткод: | G012 3050 |
| Деталь: | Rack - Front Side Fence |
| Парткод: | B039 2637 |
| Деталь: | Magnet Catch Plate |
| Парткод: | B238 2749 |
| Деталь: | Cover - Manual Feed Table |
| Парткод: | B238 2746 |
| Деталь: | EXTENSION TRAY |
| Парткод: | B238 2747 |
| Деталь: | Sheet:Damper |
| Парткод: | B238 2748 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Reverse Tray |
| Парткод: | B238 4930 |
| Деталь: | Cover - Reverse Unit Upper |
| Парткод: | B238 1269 |
| Деталь: | Cover - Paper Exit Unit Upper |
| Парткод: | B238 1268 |
| Деталь: | Exit End Fence |
| Парткод: | B223 4487 |
| Деталь: | EXIT TRAY |
| Парткод: | B223 4486 |
| Деталь: | Cover - Upper |
| Парткод: | B238 1360 |
| Деталь: | Cover - Upper EU |
| Парткод: | B237 1360 |
| Деталь: | Panel Bracket - Lower Left |
| Парткод: | B238 1585 |
| Деталь: | Scanner Cover - Front Lower |
| Парткод: | B238 1594 |
| Деталь: | Scanner Cover - Front Lower EU |
| Парткод: | B237 1594 |
| Деталь: | Panel Bracket - Lower Right |
| Парткод: | B238 1586 |
| Деталь: | Scanner Cover - Front Left |
| Парткод: | B238 1589 |
| Деталь: | Scanner Cover - Left DOM |
| Парткод: | B238 1352 |
| Деталь: | Scanner Cover - Left EU |
| Парткод: | B237 1352 |
| Деталь: | Decal - Caution Original |
| Парткод: | B237 1595 |
| Деталь: | Scanner Cover - Front Upper |
| Парткод: | B238 1597 |
| Деталь: | Scanner Cover - Rear DOM |
| Парткод: | B238 1367 |
| Деталь: | Scanner Cover - Rear EU |
| Парткод: | B237 1367 |
| Деталь: | Scanner Cover - Right DOM |
| Парткод: | B238 1354 |
| Деталь: | Scanner Cover - Right EU |
| Парткод: | B237 1354 |
| Деталь: | Drawer Bracket |
| Парткод: | B238 5891 |
| Деталь: | Cover - Inner Back DOM |
| Парткод: | B238 1363 |
| Деталь: | Cover - Inner Back EU |
| Парткод: | B237 1363 |
| Деталь: | Cover - Inner Back Middle |
| Парткод: | B223 1263 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Connector:51405-1819 |
| Парткод: | 11 029 782 |
| Деталь: | Screw:Polished Round:M4x10 |
| Парткод: | 0951 4010N |
| Деталь: | Operation Panel NA |
| Парткод: | B237 1411 |
| Деталь: | Operation Panel EU Assy |
| Парткод: | B237 1412 |
| Деталь: | Keytop - Scanner |
| Парткод: | B238 1516 |
| Деталь: | Keytop - Scanner EU |
| Парткод: | B238 1581 |
| Деталь: | Keytop - Printer |
| Парткод: | B238 1515 |
| Деталь: | Keytop - Printer EU |
| Парткод: | B238 1580 |
| Деталь: | Spacer - Keytop |
| Парткод: | B238 1547 |
| Деталь: | Operation Panel Bracket - Right |
| Парткод: | B238 1548 |
| Деталь: | PCB OP-L |
| Парткод: | B223 1475 |
| Деталь: | Harness - OP-L 12p |
| Парткод: | B238 1482 |
| Деталь: | Harness - OP-L 13p |
| Парткод: | B238 1483 |
| Деталь: | Lens - Front |
| Парткод: | B238 1519 |
| Деталь: | Screw - DIA5 |
| Парткод: | AA14 3861 |
| Деталь: | Keytop - Blank FB |
| Парткод: | B223 1518 |
| Деталь: | Keytop - Doc NA |
| Парткод: | B238 1572 |
| Деталь: | Keytop - Doc EU |
| Парткод: | B238 1578 |
| Деталь: | Keytop - Copy NA |
| Парткод: | B238 1571 |
| Деталь: | Keytop - Copy EU |
| Парткод: | B238 1577 |
| Деталь: | Keytop - Counter |
| Парткод: | B238 1511 |
| Деталь: | Operation Panel Bracket |
| Парткод: | B238 1527 |
| Деталь: | Keytop - Clear Modes |
| Парткод: | B238 1583 |
| Деталь: | Keytop - 10key NA |
| Парткод: | B238 1584 |
| Деталь: | Keytop - 10key |
| Парткод: | B238 1508 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B238 1505 |
| Деталь: | Keytop - Interrupt |
| Парткод: | B238 1509 |
| Деталь: | Keytop - Power Source |
| Парткод: | B238 1549 |
| Деталь: | Keytop - Login |
| Парткод: | B238 1550 |
| Деталь: | Harness - Invertor |
| Парткод: | B238 1484 |
| Деталь: | Keytop - Kantan |
| Парткод: | B238 1552 |
| Деталь: | Keytop - Try Print |
| Парткод: | B238 1506 |
| Деталь: | Keytop - Start |
| Парткод: | B238 1504 |
| Деталь: | Harness - OP-R 10p |
| Парткод: | B238 1480 |
| Деталь: | Harness - OP-R 13p |
| Парткод: | B238 1481 |
| Деталь: | PCB OP-R |
| Парткод: | B238 1470 |
| Деталь: | LCD - TFT W-VGA TM |
| Парткод: | B223 1485 |
| Деталь: | LCD - TFT W-VGA SH |
| Парткод: | B223 1489 |
| Деталь: | LCD Spacer B |
| Парткод: | B238 1535 |
| Деталь: | LCD Spacer A |
| Парткод: | B238 1534 |
| Деталь: | Touch Panel - W-VGA F |
| Парткод: | B223 1494 |
| Деталь: | Shadeing Plate:Touch Panel:Assy |
| Парткод: | B223 1507 |
| Деталь: | Shadeing Plate - Touch Panel |
| Парткод: | B238 1557 |
| Деталь: | INSULATOR |
| Парткод: | B238 1533 |
| Деталь: | Cable - FFC TFT LCD |
| Парткод: | B223 1487 |
| Деталь: | LCDC Bracket |
| Парткод: | B238 1556 |
| Деталь: | PCB LCDC NA |
| Парткод: | B238 1461 |
| Деталь: | PCB LCDC EU |
| Парткод: | B238 1462 |
| Деталь: | Invertor - TFT |
| Парткод: | B223 1486 |
| Деталь: | CLAMP |
| Парткод: | 11 050 032 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Clamp:LWSS-1N |
| Парткод: | 11 050 598 |
| Деталь: | Lever - Front Left |
| Парткод: | B238 1118 |
| Деталь: | Fan:Mm40x15:Nidec:L |
| Парткод: | GX64 0029 |
| Деталь: | Lever - Front Upper |
| Парткод: | B238 1119 |
| Деталь: | Right Fusing Lock Lever |
| Парткод: | G052 4696 |
| Деталь: | Density Sensor:Assy |
| Парткод: | B223 5876 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Harness - IOB Image Unit Shutter |
| Парткод: | B238 5310 |
| Деталь: | Sensor Shutter Bracket |
| Парткод: | B223 1227 |
| Деталь: | TORSION SPRING |
| Парткод: | B223 1224 |
| Деталь: | Shutter Link |
| Парткод: | B223 1225 |
| Деталь: | Sensor Link Bracket |
| Парткод: | B223 1221 |
| Деталь: | DC Motor:Shutter:Assy |
| Парткод: | B223 1213 |
| Деталь: | DC Motor Bracket |
| Парткод: | B223 1212 |
| Деталь: | Grip Bracket - Right Front |
| Парткод: | B238 1100 |
| Деталь: | Grip Shaft - Right Front |
| Парткод: | B238 1106 |
| Деталь: | Grip Cover - Right Front |
| Парткод: | B238 1105 |
| Деталь: | Grip - Right Front |
| Парткод: | B238 1104 |
| Деталь: | Bracket - Safety Switch Lever |
| Парткод: | B223 5814 |
| Деталь: | Safety Switch Bracket |
| Парткод: | B223 5813 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3568 |
| Деталь: | SCREW |
| Парткод: | B223 1317 |
| Деталь: | Grip Plate - Right Front |
| Парткод: | B238 1107 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0151 |
| Деталь: | Harness - TM/P Sensor |
| Парткод: | B238 5306 |
| Деталь: | DENSITY SENSOR |
| Парткод: | B223 6395 |
| Деталь: | DC Solenoid DC24V |
| Парткод: | B238 5875 |
| Деталь: | Hook:Solenoid:Sensor:TM |
| Парткод: | B238 5867 |
| Деталь: | Guide Plate:Machine Or Copier:Fusin |
| Парткод: | B238 1054 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Tapping Screw:M3x25 |
| Парткод: | 0451 3025N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - 4x6 |
| Парткод: | 0451 4006N |
| Деталь: | Screw:M3X25 |
| Парткод: | 0353 0250N |
| Деталь: | Switch - V-5F930DN |
| Парткод: | 12 042 709 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | Tapping Screw:3x25 |
| Парткод: | 0450 3025N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Screw - M2.5X4 |
| Парткод: | 0312 5040N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Developer:BK |
| Парткод: | B230 9640 |
| Деталь: | Developer:C |
| Парткод: | B230 9660 |
| Деталь: | Developer:M |
| Парткод: | B230 9670 |
| Деталь: | Developer:Y |
| Парткод: | B230 9680 |
| Деталь: | Development Unit:BK |
| Парткод: | B223 3013 |
| Деталь: | Development Unit:M |
| Парткод: | B223 3023 |
| Деталь: | Development Unit:C |
| Парткод: | B223 3033 |
| Деталь: | Development Unit:Y |
| Парткод: | B223 3043 |
| Деталь: | CLEANING UNIT |
| Парткод: | B223 6023 |
| Деталь: | Drum Unit:BK |
| Парткод: | B223 2244 |
| Деталь: | Drum Unit:M |
| Парткод: | B223 2245 |
| Деталь: | Drum Unit:C |
| Парткод: | B223 2246 |
| Деталь: | Drum Unit:Y |
| Парткод: | B223 2247 |
| Деталь: | Image Transfer Unit |
| Парткод: | B223 6020 |
| Деталь: | PCU:BK |
| Парткод: | B223 2204 |
| Деталь: | PCU:C |
| Парткод: | B223 2205 |
| Деталь: | PCU:M |
| Парткод: | B223 2206 |
| Деталь: | PCU:Y |
| Парткод: | B223 2207 |
| Деталь: | Toner Collection Bottle |
| Парткод: | B223 6510 |
| Деталь: | Scale - Left (A) |
| Парткод: | B238 1801 |
| Деталь: | Exposure Glass |
| Парткод: | B238 1795 |
| Деталь: | Shaft:Scale |
| Парткод: | B390 1759 |
| Деталь: | Scale - Left (B) |
| Парткод: | B238 1713 |
| Деталь: | Scale - Inner Back |
| Парткод: | B229 1751 |
| Деталь: | Exposure Glass |
| Парткод: | A250 1752 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 54 421 924 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Photointerruptor:Flat:PICH2mm:M4 |
| Парткод: | AW02 0146 |
| Деталь: | Harness - HPS/AKS |
| Парткод: | B238 5370 |
| Деталь: | Harness - BICU SIO |
| Парткод: | B238 5327 |
| Деталь: | PCB SIO |
| Парткод: | B238 5135 |
| Деталь: | Harness - SIO ARDF |
| Парткод: | B238 5374 |
| Деталь: | Harness - Lamp |
| Парткод: | B238 5369 |
| Деталь: | Document Feeder Bracket |
| Парткод: | B238 1803 |
| Деталь: | Sensor Shielding Plate |
| Парткод: | G570 1225 |
| Деталь: | Scanner Ground Plate - Rear |
| Парткод: | B238 5348 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0453 3006N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Screw - M4X12 |
| Парткод: | 0314 0120N |
Коды ошибок
101
120
121
141
142
144-001
144-002
144-003
161
165
195
202
203
204
210
211
212
213
220
222
224
226
230
231
232
233
234
235
236
237
240
241
242
243
285
290
291
292
293
294
295
296
300
301
302
303
325
360
361
362
363
364
365
366
367
372
373
374
375
380
400
441
442
443
452
460
490
491
492
498
501
502
503-01
503-02
504-01
504-02
530
531
532
533
534
535
536
540
541
542
543
544
545
547
551
552
553
554
555
557
559
561
563
564
565
610
611
620
621
622
630
632
633
634
635
650
651
669
670
672
681
682
683
687
690
725
730
740
742
746
750
760
761
763
764
770
791
792
793
794
795
796
797
818
819
820
821
822
823
824
826
827
828
829
833
839
851
853
854
855, 856
857
858
859
860
861
862
863
864
865
866
867
868
870
872
873
874
875
876
877
878
880
900
910...914
919
920
921
925
990
991
992
994
995
997
998
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 141 |
| Display: | SVC 141 ERROR |
| Description: | Motor |
| Causes: | • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor excessive PWM - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board” |
| Error code: | 142 |
| Display: | Contact the Service center. 142: Error |
| Description: | Motor |
| Causes: | • Standard white plate defective, dirty • Moisture inside the scanner unit • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor, over speed - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”. |
| Error code: | 144-001 |
| Description: | SBU connection error The SBU connection cannot be detected at power on or recovery from the energy save mode. |
| Causes: | • Insufficient power supply for SBU • Defective SBU • Defective harness • Defective detection port on the BCU |
| Remedy: | 1. Replace the harness. 2. Replace the SBU. 3. Replace the BCU. |
| Error code: | 144-002 |
| Description: | SBU serial communication error The power ON of the SBU is not detected. |
| Causes: | • Defective SIO • Defective harness • Defective detection port on the BCU |
| Remedy: | 1. Replace the harness. 2. Replace the SIO. 3. Replace the BCU. |
| Error code: | 144-003 |
| Description: | GASBU reset error The serial communication does not work. |
| Causes: | • Defective SBU • Defective detection circuit on the BCU • Defective harness |
| Remedy: | 1. Replace the SBU. 2. Replace the BCU. 3. Replace the harness. |
| Error code: | 161 |
| Display: | SYSTEM HALT (*) 161 : PCB MAIN-F6 |
| Description: | IPU Error At power on, or when the machine returns from an energy save mode, the self-diagnostic program returned an IPU error. |
| Causes: | • IPU defective • Connection between SBU and IPU is loose, broken, or defective |
| Error code: | 165 |
| Description: | Out of Paper; Load Tray 1 (MPT) with [size] [type] The Tray 1 (MPT) No Paper Sensor indicates Tray 1 (MPT) is empty. |
| Causes: | • No Paper Sensor, PL5.3.14 • No Paper Sensor Actuator, PL5.3.15 • FRONT/DUP Harness, PL5.3.28 |
| Remedy: | 1 Fill Tray 1 (MPT) with paper. Does the error persist? Go to Step 2. Complete. 2 Check the following for evidence of fault or damage: • Tray 1 (MPT) No Paper Sensor, PL5.3.14 • Sensor Actuator, PL5.3.15 Is there any damage? Replace any damaged parts. Go to Step 3. 3 Test the Tray 1 (MPT) No Paper Sensor. Run the Service Diagnostics Tray 1 (MPT) No Paper Sensor test. Does the sensor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the Tray 1 (MPT) No Paper Sensor signal. Is there +3.3 V across P/J135-1 <=> P/J135-2? Replace the sensor. Go to Step 5. 5 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J135. 2. Check continuity between J13 <=> J134. Replace the Engine Control Board. Replace the FRONT/DUP Harness. |
| Error code: | 195 |
| Description: | Serial Number Error |
| Causes: | The serial number stored in the memory (EGB) is not correct. |
| Remedy: | EEPROM defective EGB replaced without original EEPROM |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 204 |
| Display: | Power OFF/ON 204:Error |
| Description: | Polygon motor error 3: XSCRDY signal error |
| Causes: | The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing. |
| Remedy: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board). |
| Error code: | 210 |
| Description: | EM Null page cargo |
| Causes: | • Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB |
| Remedy: | 1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 211 |
| Display: | ERROR 211 HeadWARM.THERM(----) |
| Description: | EM Null page |
| Causes: | • Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB |
| Remedy: | 1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 212 |
| Description: | Install or Reseat Imaging Unit The Imaging Unit CRUM fails to detect the Imaging Unit. |
| Causes: | • Imaging Unit, PL6.1.1 • CRUM Connector, PL7.1.4 • PHD2 Harness, PL7.1.7 • FAN/PHD/MOT Harness, PL10.1.9 |
| Remedy: | 1 Remove the Imaging Unit. Inspect the printer cavity for damage, debris, and toner under the auger area preventing the Imaging Unit from being seated properly. Is there foreign material or damage? Remove foreign material. Vacuum out loose toner if found. Go to Step 2. 2 Inspect and reseat the Imaging Unit. Does the error persist?. Go to Step 3. Complete 3 Check Imaging Unit CRUM connection. Are P/J710 and P/J484 connected? Go to Step 4. Reconnect the CRUM. 4 Check all pins on the PHD2 Harness PL7.1.7 for continuity. 1. Disconnect P/J710 and P/J484. 2. Check continuity between J484<=>J710. Go to Step 5 Replace PHD2 Harness. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J484 and P/J48. 2. Check continuity between J48 <=> P484. Go to Step 6 Replace the FAN/PHD/MOT Harness 6 Replace the Imaging Unit. Does the error persist? Replace the Engine Control Board. Complete |
| Error code: | 213 |
| Display: | Power OFF/ON 213:Error |
| Description: | Install or Reseat Transfer Roller The printer does not detect the presence of the Transfer Roller. |
| Causes: | • CTD (ADC) Sensor, PL5.2.19 • Transfer Roller, PL5.1.4 • FSR/ADC Harness, PL5.2.28 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Transfer Roller PL5.1.4 • CTD (ADC) Sensor PL5.2.19 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Clean the CTD (ADC) Sensor. Does this fix the problem? Complete Go to Step 3. 3 Test the CTD (ADC) Sensor. Run the Service Diagnostics CTD (ADC) Sensor test. Does the sensor function correctly? Go to Step 4. Go to Step 5. 4 Replace the Transfer Roller. Does the error persist? Go to Step 5. Complete 5 Check the CTD (ADC) Sensor connection. Is P/J136 connected to the harness? Go to Step 6. Connect the sensor. 6 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J136. 2. Check continuity between J36 <=> J136. Go to Step 7. Replace the FSR/ ADC Harness. 7 Check the CTD (ADC) Sensor signal. Disconnect P/J36. Does J36-2 <=> J36-5 = 0 V? Replace the CTD (ADC) Sensor. Replace the Engine Control Board. |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 222 |
| Description: | Laser Synchronizing Detection Error: [M]/[C] |
| Causes: | The laser synchronizing detection signal for LDB [M]/[C] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Remedy: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB 1. Check the connectors. 2. Replace the laser optics unit. 3. Replace the EGB.· |
| Error code: | 224 |
| Description: | Laser synchronizing detection error: start position [M]: LD0 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 226 |
| Description: | Laser synchronizing detection error: start position [C]: LD0 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 231 |
| Display: | Service Call 231: Error |
| Description: | FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 232 |
| Display: | Service call 232: Error |
| Description: | FGATE ON error: Y The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [Y]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 233 |
| Description: | FGATE OFF error: Y • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [Y]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 234 |
| Description: | FGATE ON error: M The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [M]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 235 |
| Description: | FGATE OFF error: M • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [M]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 236 |
| Description: | FGATE ON error: C The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [C]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 237 |
| Description: | FGATE OFF error: C • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [C]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 240 |
| Display: | Service call 240: Error |
| Description: | LD error |
| Causes: | The IPU (EGB) detects a problem at the LD unit. |
| Remedy: | • Worn-out LD • Disconnected or broken harness of the LD. 1. Replace the laser optics unit. |
| Error code: | 241 |
| Display: | Service call 241:Error |
| Description: | LD error: Y The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 242 |
| Display: | Service call 242:Error |
| Description: | LD error: M The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 243 |
| Description: | LD error: C The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 285 |
| Description: | Line position adjustment (MUSIC) error Line position adjustment fails four consecutive times. |
| Causes: | Pattern sampling error (insufficient image density). Defective TD sensors for the line position adjustment. Defective image transfer belt unit. Defective PCDU(s). Defective laser optics housing unit. |
| Remedy: | • Check and reinstall the image transfer belt unit and PCDUs. • Check if each toner bottle has enough toner. • Replace the TD sensor. • Replace the image transfer belt unit. • Replace the PCDU(s). • Replace the laser optics housing unit. |
| Error code: | 290 |
| Description: | Shutter sensor time over error: Close The shutter close sensor does not detect "ON" for 2000 msec after the shutter motor turns on |
| Causes: | • Defective shutter close sensor • Disconnected or broken harness • Defective shutter motor • Defective shutter • Shutter motor overload • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the shutter on the laser optics housing unit. 3. Replace the shutter motor. 4. Replace the shutter close sensor. 5. Replace the IOB. |
| Error code: | 291 |
| Description: | Shutter overrun error 1: Close The shutter close sensor loses the "ON" signal after the shutter was closed. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 292 |
| Description: | Shutter overrun error 2: Close The shutter close sensor detects "ON" after SC 291 has occurred. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 293 |
| Description: | Shutter sensor time over error: Open The shutter open sensor does not detect "ON" for 2000 msec after the shutter motor turns on. |
| Causes: | • Defective shutter close sensor • Disconnected or broken harness • Defective shutter motor • Defective shutter • Shutter motor overload • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the shutter on the laser optics housing unit. 3. Replace the shutter motor. 4. Replace the shutter close sensor. 5. Replace the IOB. |
| Error code: | 294 |
| Description: | Shutter overrun error 1: Open The shutter open sensor loses the "ON" signal after the shutter was closed. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 295 |
| Description: | Shutter overrun error 2: Open The shutter open sensor detects "ON" after SC 291 has occurred. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 296 |
| Description: | Shutter open/close sensor error Both shutter open sensor and close sensor detect "ON" at the same time. |
| Causes: | • Broken harness(es) of the shutter open/close sensors |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 300 |
| Description: | High voltage power output error |
| Causes: | The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit). |
| Remedy: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB. |
| Error code: | 301 |
| Description: | Fuser web must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 303 |
| Display: | SYSTEM HALT (*) 303 : PCB MAIN ET |
| Description: | AC charge output error [Y] The measured voltage is not proper when IOB measures the charge output for each color. |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 325 |
| Display: | Open/close cover 325: Paper thickness error |
| Description: | Media detect value out of range. |
| Causes: | 1) Is different media type mixed in? 2) Is media being double fed? |
| Remedy: | Remove foreign objects. |
| Error code: | 360 |
| Display: | Set duplex unit 360: Duplex unit is open. |
| Description: | When duplex unit is removed from printer. |
| Causes: | Does error recover by resetting duplex unit? |
| Remedy: | Normal. Replace duplex unit or engine board. |
| Error code: | 361 |
| Description: | TD sensor (Vt high) error 1: M • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 362 |
| Description: | TD sensor (Vt high) error 1: C • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 363 |
| Description: | TD sensor (Vt high) error 1: Y • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 364 |
| Description: | TD sensor (Vt low) error 2: K The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 365 |
| Description: | TD sensor (Vt low) error 2: M The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 366 |
| Description: | TD sensor (Vt low) error 2: C The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 367 |
| Description: | TD sensor (Vt low) error 2: Y The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 372 |
| Display: | Check DUPLEX 372: Paper jam |
| Causes: | Check miss-feed in duplex unit. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace duplex unit. |
| Error code: | 373 |
| Description: | TD sensor adjustment error: M During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 374 |
| Description: | TD sensor adjustment error: C During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 375 |
| Description: | TD sensor adjustment error: Y During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 380 |
| Display: | Open front cover 380: Paper jam |
| Description: | Paper jam during paper feed from cassette 1, 2, 3, 4 or 5 |
| Causes: | Check miss-feed in duplex unit. |
| Remedy: | Remove miss-fed paper and set cassette. Check/replace cassette 1, 2, 3, 4, or 5. |
| Error code: | 400 |
| Display: | Open top cover 400: Paper size error |
| Description: | TM sensor error |
| Causes: | The CPU detected a low voltage of the positive reflection output under the threshold in the TM sensor. |
| Remedy: | • TM sensors are dirty. • A solid print out due to an electrostatic charging error • The TM sensor is defective. 1. Clean the TM sensors. 2. Replace the TM sensors. 3. Check the image transfer unit. 4. Turn the power Off and On. |
| Error code: | 441 |
| Description: | Image transfer unit motor error When the motor is ON, the machine monitors the lock signals every 100 ms. If the High status occurs 20 times consecutively, the machine judges that the motor is not rotating correctly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Shorted 24 V fuse on the PSU. Defective interlock systeme PSU. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system |
| Error code: | 442 |
| Description: | Image transfer belt contact motor error The image transfer belt contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates. |
| Causes: | Motor overload. Defective motor. Loose connection. Disconnected harness. Shorted 24 V fuse on the PSU. Defective interlock system. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Replace the interlock switch. • Replace the IOB. |
| Error code: | 443 |
| Description: | Image transfer unit error The machine detects the encoder sensor error. |
| Causes: | Defective encoder sensor. Defective image transfer unit motor. Image transfer unit installation error. Loose connection. Broken harness. |
| Remedy: | • Replace the image transfer unit. • Replace the image transfer unit motor. • Reinstall the image transfer unit. • Replace the encoder sensor. • Reconnect the connector. • Replace the harness. |
| Error code: | 452 |
| Description: | Paper transfer unit contact error The paper transfer unit contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates. |
| Causes: | Motor overload. Defective motor. Loose connection. Disconnected harness. Shorted 24 V fuse on the PSU. Defective interlock system. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system. • Replace the IOB. |
| Error code: | 460 |
| Description: | DC Separation Corona Output Error A dc separation feedback voltage of less than 0.5 V was detected after more than 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 490 |
| Display: | Set 490: No paper in MP tray (* stands for A4 B4, etc.) |
| Description: | ITB (Image Transfer Belt) Unit Set Error |
| Causes: | The TM sensor does not detect the reflection from the ITB. |
| Remedy: | • No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S |
| Error code: | 491 |
| Description: | High voltage power: Drum / development bias output error An error signal is detected for 200 ms when charging the drum or development. |
| Causes: | High voltage leak. Loose connection. Broken harness. Defective drum unit or development unit. Defective high voltage supply unit. |
| Remedy: | • Turn the main power switch off and on. • Reattach/replace the harness and parts on the high voltage power supply route. • Replace the drum unit or development unit. • Replace the high voltage supply unit. |
| Error code: | 492 |
| Description: | High voltage power: Image transfer / paper transfer bias output error An error signal is detected for 200 ms when charging the separation, image transfer bet or paper transfer roller. |
| Causes: | High voltage leak. Broken harness Defective image transfer belt unit or paper transfer unit. Defective high voltage supply unit. |
| Remedy: | • Turn the main power switch off and on. • Reattach/replace the harness and parts on the high voltage power supply route. • Replace/reinstall the high-voltage supply unit. • Replace the high voltage supply unit. |
| Error code: | 498 |
| Description: | Temperature and humidity sensor error 2 Thermal sensor output error: If the output value is 0.5 V or lower or 3.0 V or higher, it is judged as a sensor error and the presumptive temperature, 23C, is applied. Humidity sensor output error: If the output value is 2.4V or higher, it is judged as a sensor error and the presumptive humidity, 50 % RH, is applied. If a sensor error is judged to have occurred to the thermal sensor or humidity sensor three times consecutively, the machine issues SC498-00. * However, if the power is switched off and then back on, the machine resumes its attempt to use the sensor. * If the thermal sensor or humidity sensor remains capable of normal operation even after the SC is issued, the capable sensor will keep operating. |
| Causes: | Loose connection/harness disconnected. Defective sensor. |
| Remedy: | • Reconnect to the connector. • Check the harness. |
| Error code: | 501 |
| Display: | Service Call 501: Error |
| Description: | Tray 1 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503-01 |
| Description: | Tray 3 error (Paper Tray Unit, Paper Feed Unit or LCT) For the two-tray paper feed unit or one-tray paper tray unit: • When the tray lift motor is turned on, the upper limit is not detected within 10 seconds For the LCT: • SC 503-01 occurs if the upper or lower limit is not detected within 8 seconds when the tray lift motor is turned on to lift or lower the tray. |
| Causes: | For the two-tray paper feed unit or one-tray paper tray unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection • Defective upper limit sensor or connector disconnection • Defective tray lift motor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 503-02 |
| Description: | Tray 3 error (Paper Tray Unit, Paper Feed Unit or LCT) This SC is generated if the following condition occurs 3 consecutive times. For the two-tray paper feed unit or one-tray paper tray unit: • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. For the LCT: • When the main switch is turned on or when the LCT is set, if the end fence is not in the home position (home position sensor ON), the tray lift motor stops. • If the upper limit does not go off for 1.5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on. |
| Causes: | For the two-tray paper feed unit or one-tray paper tray unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 504-01 |
| Description: | Tray 4 error (Paper Tray Unit, Paper Feed Unit or LCT) For the two-tray paper feed unit or one-tray paper tray unit When the tray lift motor is turned on, the upper limit is not detected within 10 seconds. For the LCT If the upper or lower limit is not detected within 8 seconds when the tray lift motor is turned on to lift up or lower the tray |
| Causes: | • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 504-02 |
| Description: | Tray 4 error (Paper Tray Unit, Paper Feed Unit or LCT) This SC is generated if the following condition occurs 3 consecutive times. For the two-tray paper feed unit or one-tray paper tray unit • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. For the LCT • If the upper limit does not go off for 1.5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on. |
| Causes: | For the two-tray paper feed unit or one-tray paper tray unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 530 |
| Description: | LSU Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the LSU fan motor. |
| Error code: | 531 |
| Description: | Fusing Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the fusing fan motor. |
| Error code: | 532 |
| Description: | IH coil fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH coil fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH coil fan motor • Defective IH coil fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH coil fan. 3. Replace the IOB. |
| Error code: | 533 |
| Description: | IH inverter fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH inverter fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH inverter fan motor • Defective IH inverter fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH inverter fan. 3. Replace the IOB. |
| Error code: | 534 |
| Description: | Second duct fan error The machine does not detect the fan motor lock signal for 2 seconds while the second duct fan turns on. |
| Causes: | • Disconnected harness • Overload on the second duct fan motor • Defective second duct motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the second duct fan. 3. Replace the IOB. |
| Error code: | 535 |
| Description: | Paper exit fan error The lock sensor value is monitored every 100 ms when the motor is ON. If the retrieval of the lock signal fails 100 times consecutively, it is determined as a failure to rotate properly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 536 |
| Description: | Third duct fan error The motor lock signal error is detected for 10 seconds after the motor lock signal was first detected. |
| Causes: | • Defective controller fan motor |
| Remedy: | 1. Replace the controller fan motor. 2. Replace the IOB. |
| Error code: | 540 |
| Description: | Fusing/Paper exit motor error At the fusing delivery brushless motor, the lock signal is monitored every 100 ms. If the High status occurs consecutively 20 times, it is determined as a failure to rotate properly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Shorted 24 V fuse on the PSU. Defective interlock system. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 554 |
| Description: | Fusing sleeve belt overheat: End (hardware error) The fusing sleeve belt thermistor detects 250°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 555 |
| Description: | Fusing Heater error: End The fusing heater keeps full power for 9 seconds or more. |
| Causes: | Defective thermistors. Broken heater cables. |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 561 |
| Description: | Pressure roller end thermistor error 1 During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the end thermistor on the pressure roller returned a digital reading of more than 3.3V. |
| Causes: | • Pressure roller end thermistor not positioned properly • Pressure roller end thermistor connector loose, broken, defective • Pressure roller end thermistor defective • MCU defective |
| Error code: | 563 |
| Description: | Pressure roller end thermistor error 2 During the hot roller temperature control sequence, the end thermistor on the pressure roller returned a digital reading of less than 0.2V. |
| Causes: | • Pressure roller end thermistor connector loose • Pressure roller end thermistor short circuit, defective • MCU defective |
| Error code: | 564 |
| Description: | Pressure roller overheat: End (hardware error) The thermistor detects 240°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: • The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 565 |
| Description: | Pressure roller fusing lamp consecutive full power 3 When the fusing unit is not running in the ready condition, the pressure roller fusing lamp keeps ON full power for 180 seconds or more. |
| Causes: | • Broken pressure roller fusing lamp |
| Remedy: | 1. Replace the pressure roller fusing lamp. 2. Replace the pressure roller thermistor. 3. Replace the PSU. |
| Error code: | 610 |
| Display: | ERROR 610 NOT FILLUP |
| Description: | Mechanical counter error: Bk This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 611 |
| Display: | ERROR 611 Case Weight |
| Description: | Mechanical counter error: FC This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 622 |
| Description: | Paper Bank communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The paper bank`s control board is faulty. Defective BCU/IOB. The paper bank`s connection is faulty. |
| Remedy: | • Reconnect the paper bank cables. • Replace the BCU. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 630 |
| Description: | CSS communication error A communication error occurred during communication with the CSS. |
| Causes: | • Communication line error |
| Remedy: | Logging only. |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 633 |
| Description: | Key/card counter device error 2 During communication with the device, the MCU received a break (Low) signal. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 650 |
| Description: | @Remote communication error 1 A dial-up or modem error occurred during @Remote operation. (This error occurs only during @Remote operation.) |
| Causes: | • Modem line disconnected • Modem board missing or not properly installed |
| Error code: | 651 |
| Description: | @Remote communication error 2 An illegal dial-up to the service center was attempted by @Remote. |
| Causes: | • Software bug |
| Error code: | 669 |
| Description: | EEPROM Error |
| Causes: | An unexpected value exists in the initialization flag of the EEPROM |
| Remedy: | • EEPROM not initialized • Defective EEPROM |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 681 |
| Description: | Toner bottle ID: Communication error -01 D Device ID is not identified: K -02 D Device ID is not identified: M -03 D Device ID is not identified: C -04 D Device ID is not identified: Y -06 D Channel error: K -07 D Channel error: M -08 D Channel error: C -09 D Channel error: Y -11 D Device error: K -12 D Device error: M -13 D Device error: C -14 D Device error: Y -16 D Communication interruption (an error during communication): K -17 D Communication interruption (an error during communication): M -18 D Communication interruption (an error during communication): C -19 D Communication interruption (an error during communication): Y -21 D Communication time-out: K -22 D Communication time-out: M -23 D Communication time-out: C -24 D Communication time-out: Y -26 D Device operation suspended (logically suspended): K -27 D Device operation suspended (logically suspended): M -28 D Device operation suspended (logically suspended): C -29 D Device operation suspended (logically suspended): Y -31 D The requested buffer is full: K -32 D The requested buffer is full: M -33 D The requested buffer is full: C -34 D The requested buffer is full: Y -36 D No error code: K -37 D No error code: M -38 D No error code: C -39 D No error code: Y |
| Causes: | Communication error occurs when the toner bottle ID starts to communicate with the toner bottle ID receptor. Retry of toner bottle ID communication fails three times after the machine has detected the toner bottle ID communication error. • 01-04 Damaged memory chip data • 06-09 Disconnected interface • 11-14 No memory chip on the toner cartridge • 16-9, 21-24, 26-39 Caused by noise • 31-34, 36-39 Software problem • Replace the toner bottle detection board. • Replace the toner cartridge. • Turn the main power switch off and on. |
| Error code: | 682 |
| Description: | Memory chip at TD sensor: Communication error |
| Causes: | • 01-04 Damaged memory chip data • 06-09 Disconnected interface • 11-14 No memory chip on the toner cartridge • 16-19, 21-24, 26-39 Caused by noise • 31-34, 36-39 Software problem |
| Remedy: | • Replace the PCU. • Turn the main power switch off and on. |
| Error code: | 683 |
| Description: | RFID: Unit check error The machine gets RFID communication error even the toner cartridges have not been installed in the machine |
| Causes: | Caused by noise |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 690 |
| Description: | GAVD Communication Error |
| Causes: | The ID of the GAVD is not identified during initialization. The chip ID of the GAVD cannot be detected by the machine at power-on. |
| Remedy: | • Defective EGB 1. Replace the EGB. EE |
| Error code: | 725 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor. 4. Replace the finisher main board. |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 740 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished after a certain time. For the 1000-sheet booklet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 742 |
| Description: | Finisher stapler movement motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished for a certain time. For the 1000-sheet booklet finisher • The stapler HP sensor is not activated within the specified time after the stapler motor turned on. (first detection: jam error, consecutive twice detection SC code). |
| Causes: | • Motor overload • Loose connection of the stapler home position sensor • Loose connection of the stapler movement motor • Defective stapler home position sensor • Defective stapler movement motor |
| Remedy: | 1. Check the connection of the stapler movement motor. 2. Check the connection of the stapler home position sensor. 3. Replace the stapler home position sensor. 4. Replace the stapler movement motor. |
| Error code: | 746 |
| Description: | 1000-sheet booklet finisher: Stack feed motor error • The stack feed HP sensor does not detect "ON" twice (once: jam error) for specified time after the stack feed motor has turned on. • The stack feed HP sensor does not detect "OFF" twice (once: jam error) for specified time after the stack feed motor has turned on. |
| Causes: | • Motor overload • Loose connection of the stack feed motor • Defective stack feed motor |
| Remedy: | 1. Check the connections and cables for the stack feed motor and HP sensor. 2. Check for blockages in the stack feed motor mechanism. 3. Replace the stack feed HP sensor and/or stack feed motor 4. Replace the finisher main board. |
| Error code: | 750 |
| Description: | 1000/3000-sheet (booklet) finisher: Tray lift motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. |
| Causes: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor |
| Remedy: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor. |
| Error code: | 760 |
| Description: | Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Punch HP sensor disconnected, defective • Punch motor disconnected or defective • Punch motor overload due to obstruction |
| Remedy: | 1. Check the connections and cables for the punch motor and HP sensor. 2. Check for blockages in the punch motor mechanism. 3. Replace the punch HP sensor and/or punch motor 4. Replace the finisher main board. |
| Error code: | 761 |
| Description: | Finisher folder plate motor error The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Remedy: | 1. Check the connections and cables for the folder plate motor and HP sensor. 2. Check for blockages in the folder plate motor mechanism. 3. Replace the folder plate HP sensor and/or folder plate motor 4. Replace the finisher main board. |
| Error code: | 763 |
| Description: | Rear fold plate HP sensor error The state (on/off, off/on) of the rear fold plate HP sensor in the fan fold unit did not change 1 sec. after the plate started to move. |
| Causes: | • Fold plate motor (R) harness connector loose, disconnected, broken • Rear fold plate HP sensor harness connector loose, disconnected, broken • Fold plate motor (R) defective • Rear fold plate HP sensor defective • Undetected paper is jamming the action of the motor or fold plate • Fan folder unit MCU defective |
| Error code: | 764 |
| Description: | Paper position sensor slide motor error The paper position sensor moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the paper position sensor slide motor. 2. Replace the paper position sensor slide motor. |
| Error code: | 770 |
| Description: | Shift motor error The shift motor HP sensor does not detect any change for 1.86 seconds after the shift motor has turned on at power on or during its operation. |
| Causes: | Defective shift motor. Defective shift motor HP sensors. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 791 |
| Description: | Bridge unit error The machine recognizes the finisher, but does not recognize the bridge unit. |
| Causes: | The bridge unit is not installed. Defective bridge unit. Re-install the bridge unit. Turn the main power switch off and on. |
| Remedy: | • Re-install the bridge unit. • Turn the main power switch off and on. |
| Error code: | 792 |
| Description: | Finisher error The machine does not recognize the finisher, but recognizes the bridge unit. |
| Causes: | The finisher`s connection is faulty. The finisher is not attached to a device equipped with the bridge unit. Defective finisher. |
| Remedy: | Reconnect the finisher or bridge unit, and then turn the main power switch off and then back on. |
| Error code: | 793 |
| Description: | Finisher gathering roller motor error |
| Causes: | • Motor overload • Loose connection of the gathering roller motor • Defective gathering roller motor |
| Remedy: | • Check the connections to the gathering roller motor. • Replace the gathering roller motor. |
| Error code: | 794 |
| Description: | Finisher exit guide plate motor error |
| Causes: | • Motor overload • Loose connection of the exit guide plate motor • Defective exit guide plate motor |
| Remedy: | 1. Check the connections to the exit guide plate motor. 2. Replace the exit guide plate motor. |
| Error code: | 795 |
| Description: | Finisher shift roller motor error |
| Causes: | • Motor overload • Loose connection of the shift roller motor • Defective shift roller motor |
| Remedy: | • Check the connections to the shift roller motor. • Replace the shift roller motor. |
| Error code: | 796 |
| Description: | Finisher tray lift motor error |
| Causes: | • Motor overload • Loose connection of the tray lift motor • Defective tray lift motor |
| Remedy: | • Check the connections to the tray lift motor. • Replace the tray lift motor. |
| Error code: | 797 |
| Description: | EEPROM data error |
| Causes: | Defective EEPROM on the main board |
| Remedy: | 1. Check the harness connection. 2. Replace the main board. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 833 |
| Display: | SYSTEM HALT (*) 833 : FW/PRN MDL |
| Description: | Self-diagnostic error 8: Engine I/F ASIC |
| Causes: | [0F30] [0F31] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. [0F41] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. |
| Error code: | 839 |
| Display: | SYSTEM HALT (*) 839 : FW/PRN MDL |
| Description: | Serial Flash A read/write operation on the Software Status Register failed. |
| Causes: | • Replace the controller board |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855, 856 |
| Description: | Wireless LAN/Bluetooth card error An error is detected in the wireless LAN/Bluetooth card. |
| Causes: | • Loose connection • Defective wireless LAN/Bluetooth card |
| Remedy: | 1. Check the connection. 2. Replace the wireless LAN/Bluetooth card. |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 858 |
| Description: | Data encryption conversion error (1) |
| Causes: | -01 A serious error has occurred during the data conversion performed for updating the key for data encryption. • The data in the USB flash drive is damaged. • A communication error has occurred due to electromagnetic waves or other noise. • Replace the controller board. * However, if it is "-30", the machine may recover by turning the main power switch off and then back on. -02 A Data encryption conversion error (2) A serious error occurs when data is encrypted to update an encryption key. Defective NVRAM Replace the controller board. -30 A Data encryption conversion error (3) A recoverable error has occurred before starting data conversion. Defective NVRAM • Turn the main switch off and on. • If the error reoccurs, replace the controller board. -31 A A serious error occurs while the data is encrypted. Same as SC991 Same as SC991 |
| Error code: | 859 |
| Description: | HDD data encryption error |
| Causes: | -01 B HDD check error • Hard disk data conversion has been selected, but the hard disk is not installed. • The hard disk is not mounted properly. • No HDD installed • Hard disk formatting is not completed. • The encryption key on the board and the actual encryption key in the hard disk do not match. • Install the HDD correctly. • Initialize the HDD with SP5-832-001. -02 B Power failure during data encryption. The data conversion in the NVRAM or hard disk has not completed successfully. Power interruption has occurred during the conversion of the data in the NVRAM or hard disk Initialize the HDD with SP5-832-001. -10 B Data Read/Write command error Due to time-out, serial communication error, or other problems in DMAC, an irregular DMAC return value has occurred consecutively two or more times Noise or other problems in the SATA connection Same as SC863 |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 862 |
| Description: | Bad sector number error The number of bad sectors in the HDD (image data area) goes over 101. |
| Causes: | • Defective HDD |
| Remedy: | Format the HDD with SP5832-001. Replace the HDD. |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 877 |
| Description: | HDD Data Erase Error The Data Overwrite Security option cannot scramble and erase data on the HDD because the DOS SD card has been corrupted or has |
| Causes: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not been removed from the SD card slot. |
| Remedy: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not solve the problem, the SD card has been damaged.) • Install a new NVRAM • Install a new Data Overwrite Security option with a new SD card |
| Error code: | 878 |
| Description: | TPM electronic recognition error |
| Causes: | -00 The system firmware is not authenticated by TPM. The system hash value registered in the TPM at the machine`s system startup does not match that registered in the USB flash drive. • The system module was updated without going through the formal update process. • Incorrect operating of the USB flash. Replace the board. -01 D USB Flash error An error has occurred in the file system in the USB flash drive. The file system of the USB flash drive is damaged. Replace the controller board. -02 D TPM error An error has occurred in the TPM or TPM driver. Defective TPM Replace the controller board. -03 D TCSD error An error has occurred in the TPM software stack. • The TPM software stack cannot be launched. • The file required for the TPM software stack is missing. Replace the controller board. |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 910...914 |
| Description: | External Controller Error |
| Causes: | The external controller alerted the machine about an error. |
| Remedy: | 1. Please refer to the instructions for the external controller (application). |
| Error code: | 919 |
| Display: | Power Off/on 919: Error |
| Description: | Power Supply Fan Error |
| Causes: | • Controller RW3600 power outtage • Controller RW3600 rebooted • Connection to Controller RW3600 loose |
| Remedy: | 1 Is CN17 on the printer controller board properly connected? Go to step 2. Connect CN17. 2 Is CN6 on the CK2 daughter board properly connected? Go to step 3. Connect CN6. 3 Is +24 V present between pins 1 and 3 of connector CN6 on the CK2 daughter board? Replace the power supply fan. Replace the printer controller board. 4 Did either exchange solve the problem? Problem solved. Replace the CK2 daughter board. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 994 |
| Display: | Service Call 994:Error |
| Description: | Density Sensor Error |
| Causes: | • No action required because this SC does not interfere with operation of the machine. |
| Remedy: | 1 Is the front door fully closed? Go to step 2. Close the front door. 2 Is the density sensor actuator stuck in place? Release the density sensor actuator. Go to step 3. 3 Are connectors CN406 and CN407 on the sensor board connected properly? Go to step 4. Plug the connector in securely. 4 Is connector CN15 on the printer controller board connected properly? Replace the density sensor. Go to step 5. Plug the connector in securely. 5 Did replacing the density sensor fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 995 |
| Description: | Finisher Main Feed Motor abnormal |
| Causes: | -01 D • Defective BCU • NVRAM Replacement error • Install the previous NVRAM • Input the serial number with SP5-811-004, and turn the main power switch off and on. -02 D • Defective NVRAM • Defective controller Perform SP5-825 to download the appropriate data to the NVRAM, and then turn the main power switch off and then back on. -03 D The serial number cannot be identified due to a mistake during controller replacement or mechanical failure. Replace the controller with the correct type. -04 D - Place all parts in the initial state, and then replace the parts according to the procedures described in the manuals. |
| Remedy: | 1 Is there jammed paper or other obstructions in the paper path? Clear the paper path. Go to step 2. 2 Check to ensure the connector PJ6 on the finisher control board and the feed motor assembly cable are properly connected. Are the cables properly connected? Go to step 3. Properly connect the cables. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pins 7 and 8 and +5 V dc (–10%) between pins 7 and 6 on the feed motor assembly cable connector CN1. Is either voltage missing? Go to step 4. Go to step 5. 4 Disconnect the feed motor assembly cable and PJ6 on the finisher control board. Measure continuity on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 5 Replace the feed motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 6 Measure for +24 V dc between pins 1 and 2 on connector PJ3 on the finisher control board. Measure for +5 V dc between pins 1 and 3 on PJ2 on the finisher control board. Is either voltage missing? Replace the power supply. Replace the finisher control board. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
Парткод
Название
RICOH TYPE K Скрепки с картриджем
RICOH TYPE K Скрепки (3 упаковки)
RICOH TYPE S Скрепки буклетные в картридже для SR3000
RICOH TYPE MP-C3000E Тонер-картридж черный
RICOH MP-C3000E Тонер-картридж желтый
RICOH MP-C3000E Тонер-картридж пурпурный
RICOH MP-C3000E Тонер-картридж голубой
RICOH Блок проявки черный с девелопером
RICOH Блок проявки пурпурный с девелопером
RICOH Блок проявки голубой с девелопером
RICOH Блок проявки желтый с девелопером
(B2232027) RICOH Блок фотобарабанов цветной CMY
(B2232042) RICOH Блок фотобарабана черный
RICOH Девелопер черный
RICOH Девелопер голубой
RICOH Девелопер пурпурный
RICOH Девелопер желтый
