Ricoh MPC3500
Рейтинг
Модули
EXTERIOR 2
PAPER FEED SECTION
ARDF Electrical Section
Original Transfer 3
FUSING UNIT 3
EXTERIOR 3
Controller Unit
By-pass Feed Section 2
SCANNER SECTION 2
DUPLEX UNIT 1
DRIVE SECTION 4
Frame Section 4
LD unit
ELECTRICAL SECTION 1
Original Feed 3
PAPER EXIT SECTION 1
FRAME SECTION 1
ARDF Exterior
FUSING UNIT 2
DUPLEX UNIT 5
DUPLEX UNIT 2
DUPLEX UNIT 4
Original Transfer 2
ACCESSORIES
PAPER EXIT SECTION 2
Toner Supply Unit 1
PAPER REGISTRATION
FUSING UNIT 1
Drive Section 1
ELECTRICAL SECTION 2
Original Feed 2
ELECTRICAL SECTION 3
2nd Paper Tray
ELECTRICAL SECTION 4
OPERATION PANEL
Frame Section 3
DUPLEX UNIT 3
ARDF Drive Section 1
Original Feed 1
Paper Separation
Scanner Section 1
DRIVE SECTION 3
DRIVE SECTION 2
SCANNER SECTION 3
TONER SUPPLY UNIT 2
Drive Section 5
1st Paper Tray
By-pass Feed Section 1
ARDF Frame Section
ARDF Drive Section 2
EXTERIOR 1
Original Transfer 1
FRAME SECTION 2
Детали ARDF Drive Section 2
| Деталь: | Cover:Scanner:Left |
| Парткод: | B223 1818 |
| Деталь: | Cover:Scanner:Left:EU |
| Парткод: | B222 1818 |
| Деталь: | Cover:Left:Upper |
| Парткод: | B223 1282 |
| Деталь: | Exit End Fence |
| Парткод: | B223 4487 |
| Деталь: | EXIT TRAY |
| Парткод: | B223 4486 |
| Деталь: | Cover:Upper |
| Парткод: | B223 1260 |
| Деталь: | Cover:Inner Back:Upper |
| Парткод: | B223 1262 |
| Деталь: | Cover - Inner Back Middle |
| Парткод: | B223 1263 |
| Деталь: | Cover:Inner Back |
| Парткод: | B223 1261 |
| Деталь: | Cover:Paper Exit Unit:Upper |
| Парткод: | B223 1266 |
| Деталь: | Cover:Right:Upper Middle |
| Парткод: | B223 1273 |
| Деталь: | Cover:Scanner:Right |
| Парткод: | B223 1819 |
| Деталь: | Cover:Scanner:Right:EU |
| Парткод: | B222 1819 |
| Деталь: | Cover:Scanner:Rear |
| Парткод: | B223 1820 |
| Деталь: | Cover:Scanner:Rear:EU |
| Парткод: | B222 1820 |
| Деталь: | Ozone Filter:No.2 |
| Парткод: | B223 1278 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Screw:M3X3 |
| Парткод: | 0353 0030N |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | PAPER FEED UNIT |
| Парткод: | B223 2750 |
| Деталь: | Paper End Feeler |
| Парткод: | B223 2767 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Harness - Paper Feed Unit |
| Парткод: | B223 2773 |
| Деталь: | Sensor bracket |
| Парткод: | B223 2778 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0128 |
| Деталь: | Bracket:Sensor |
| Парткод: | B082 2781 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0122 |
| Деталь: | DC Solenoid 24V |
| Парткод: | B223 2780 |
| Деталь: | STAY |
| Парткод: | B223 2776 |
| Деталь: | Transport Roller |
| Парткод: | B238 2569 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2143 |
| Деталь: | Harness Sheet |
| Парткод: | B223 2772 |
| Деталь: | Ground Plate - Front |
| Парткод: | B223 2786 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF03 0090 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1252 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | Feed guide |
| Парткод: | B223 2829 |
| Деталь: | Paper Feed Roller:Feed |
| Парткод: | AF03 1090 |
| Деталь: | Gear - Roller Clutch |
| Парткод: | AB01 1218 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Ground Plate - Feed |
| Парткод: | B223 2765 |
| Деталь: | Pickup Arm |
| Парткод: | B223 2761 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0691 |
| Деталь: | Lever - Feed |
| Парткод: | G065 2767 |
| Деталь: | Gear-24z |
| Парткод: | B223 2764 |
| Деталь: | Feed Shaft |
| Парткод: | B223 2762 |
| Деталь: | Paper Feed Roller:Separate |
| Парткод: | AF03 2090 |
| Деталь: | TORQUE LIMITER |
| Парткод: | B004 2783 |
| Деталь: | Separate Driven Shaft |
| Парткод: | B223 2810 |
| Деталь: | Gear:Separate:Driven |
| Парткод: | AB01 0157 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0693 |
| Деталь: | PRESSURE LEVER |
| Парткод: | G065 2774 |
| Деталь: | Gear:Separate:Drive |
| Парткод: | AB01 0156 |
| Деталь: | Separate Drive Shaft |
| Парткод: | B223 2815 |
| Деталь: | Gear - 22Z |
| Парткод: | B223 2819 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Release Lever |
| Парткод: | G065 2776 |
| Деталь: | LINK LEVER |
| Парткод: | G065 2775 |
| Деталь: | Spring - Release |
| Парткод: | AA06 2259 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Tapping Screw:3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | HARNESS:INTERFACE |
| Парткод: | B802 5710 |
| Деталь: | Bracket:PCB:Right |
| Парткод: | B802 1231 |
| Деталь: | Harness:Lift_up |
| Парткод: | B802 5780 |
| Деталь: | Harness:Paper Feed |
| Парткод: | B802 5730 |
| Деталь: | Harness:Solenoid |
| Парткод: | B802 5800 |
| Деталь: | Harness:Motor:Reverse |
| Парткод: | B802 5770 |
| Деталь: | Harness:Original Table |
| Парткод: | B802 5740 |
| Деталь: | Harness:Guide |
| Парткод: | B802 5830 |
| Деталь: | Harness:Motor:Paper Feed |
| Парткод: | B802 5760 |
| Деталь: | Harness:Motor:Pick Up |
| Парткод: | B802 5820 |
| Деталь: | PCB:Main |
| Парткод: | B802 5500 |
| Деталь: | Bracket:On Off Detector |
| Парткод: | B802 1246 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Bracket:PCB:Left |
| Парткод: | B802 1236 |
| Деталь: | Timing Belt:B40S2M390 |
| Парткод: | B703 1165 |
| Деталь: | Bracket:Motor |
| Парткод: | B802 1612 |
| Деталь: | Screw:6x1.7 |
| Парткод: | AA14 3802 |
| Деталь: | Bracket:Coupling |
| Парткод: | B802 1624 |
| Деталь: | Stay:Motor |
| Парткод: | B802 1616 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0842 |
| Деталь: | Stepper Motor:DC24V 4.8W |
| Парткод: | B802 1621 |
| Деталь: | Spring - Paper Size Sensor |
| Парткод: | B387 1951 |
| Деталь: | Paper Size Sensor Feeler |
| Парткод: | B789 1942 |
| Деталь: | Plate:Harness:Guide |
| Парткод: | B802 1412 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Binding Self Tapping Screw:4x6 |
| Парткод: | 0453 4006N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11 050 522 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Edge Saddle - Eds-0607l |
| Парткод: | 11 050 514 |
| Деталь: | SCREW |
| Парткод: | B238 4483 |
| Деталь: | Bracket:Tension |
| Парткод: | B802 1755 |
| Деталь: | Timing Pulley:T31 |
| Парткод: | B802 1762 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0842 |
| Деталь: | Timing Belt:40S1.5M378 |
| Парткод: | AA04 3321 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Pulley:Idler:DIA16 |
| Парткод: | B802 1767 |
| Деталь: | Timing Pulley:T26 |
| Парткод: | B802 3312 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 2260 |
| Деталь: | Link:Solenoid |
| Парткод: | B802 3631 |
| Деталь: | Lever:Exchange Powl:Reverse |
| Парткод: | B802 3615 |
| Деталь: | Snap Ring |
| Парткод: | G020 1160 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Screw:Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Guide:Paper Feed:Lower |
| Парткод: | B802 3351 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | Roller:Pull Out |
| Парткод: | B802 3211 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Decal:Display:Misfeed Removal:P3 |
| Парткод: | B802 6015 |
| Деталь: | Guide:Exit:Upper |
| Парткод: | B802 3651 |
| Деталь: | Roller:Exit |
| Парткод: | B802 3311 |
| Деталь: | Cushion:Exchange Powl |
| Парткод: | B802 3612 |
| Деталь: | Exchange Powl:Reverse |
| Парткод: | B802 3611 |
| Деталь: | Timing Pulley:T23 |
| Парткод: | B802 3332 |
| Деталь: | Discharge Brush:Exit |
| Парткод: | B802 3756 |
| Деталь: | Stay:Reverse |
| Парткод: | B802 3751 |
| Деталь: | Roller:Reverse |
| Парткод: | B802 3331 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | 7 423 808 |
| Деталь: | Ball Bearing - 6x12x4 Mm |
| Парткод: | 7 413 506 |
| Деталь: | Fan Motor DC24V 1.92W |
| Парткод: | GX64 0021 |
| Деталь: | Duct:Exit |
| Парткод: | B223 1336 |
| Деталь: | Holder:Coil:Front Lower |
| Парткод: | B223 4311 |
| Деталь: | Holder:Coil:Rear Lower |
| Парткод: | B223 4312 |
| Деталь: | Stay:IH:Holder |
| Парткод: | B223 4310 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | 54 472 768 |
| Деталь: | Bracket:Fan:Ih |
| Парткод: | B223 1328 |
| Деталь: | Sirocco Fan:DC24V 2.6W |
| Парткод: | AX65 0045 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Bracket:Sensor:Machine Or Copier |
| Парткод: | B223 4329 |
| Деталь: | Bracket:Pin |
| Парткод: | B223 4337 |
| Деталь: | Bracket:Sensor:Turn |
| Парткод: | B223 4328 |
| Деталь: | Bracket:Pressure:Coil |
| Парткод: | B223 4308 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3438 |
| Деталь: | Guide:IH:Upper |
| Парткод: | B223 4307 |
| Деталь: | Compression Spring:Lever |
| Парткод: | AA06 3439 |
| Деталь: | Lever:Lock:Fusing Unit |
| Парткод: | B223 4327 |
| Деталь: | Supporter:Fusing Unit |
| Парткод: | B223 4336 |
| Деталь: | Frame:Coil:Front |
| Парткод: | B223 4301 |
| Деталь: | Frame:Coil:Rear |
| Парткод: | B223 4303 |
| Деталь: | IH Coil Unit |
| Парткод: | B223 4349 |
| Деталь: | IH Coilunit:EU |
| Парткод: | B223 4011 |
| Деталь: | Holder:Fusing Unit:Assy |
| Парткод: | B223 4360 |
| Деталь: | Guide:Fusing Unit |
| Парткод: | B223 4341 |
| Деталь: | Decal:Warning (High Temperature) |
| Парткод: | B223 4397 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw:3x10 |
| Парткод: | 0451 3010N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Screw - M3X4 |
| Парткод: | 0353 0040N |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | Inner Cover:Upper:Left |
| Парткод: | B223 1241 |
| Деталь: | Decal:Colored Display:BK:Inner Cover |
| Парткод: | B238 3364 |
| Деталь: | Decal:Colored Display:Y:Inner Cover |
| Парткод: | B238 3365 |
| Деталь: | Decal:Colored Display:C:Inner Cover |
| Парткод: | B238 3366 |
| Деталь: | Decal:Colored Display:M:Inner Cover |
| Парткод: | B238 3367 |
| Деталь: | Inner Cover - Middle |
| Парткод: | B223 1244 |
| Деталь: | Decal - Cleaning |
| Парткод: | B238 1368 |
| Деталь: | Decal - Shielding Plate Y |
| Парткод: | GA00 3030 |
| Деталь: | Decal - Shielding Plate C |
| Парткод: | GA00 3032 |
| Деталь: | Decal - Shielding Plate M |
| Парткод: | GA00 3031 |
| Деталь: | Decal - Shielding Plate K |
| Парткод: | GA00 3033 |
| Деталь: | Stopper:Lever:Drum Stay |
| Парткод: | B223 1304 |
| Деталь: | Decal - Misfeed Removal B1 |
| Парткод: | B238 1362 |
| Деталь: | Drum Stay PCU Assy |
| Парткод: | B223 1300 |
| Деталь: | Drum Stay Lever |
| Парткод: | B223 1303 |
| Деталь: | SPRING |
| Парткод: | B223 1318 |
| Деталь: | Drum Stay |
| Парткод: | B223 1306 |
| Деталь: | WIRE |
| Парткод: | B223 1319 |
| Деталь: | Ball Bearing Plate |
| Парткод: | B223 1315 |
| Деталь: | Ball Bearing Clip |
| Парткод: | B223 1316 |
| Деталь: | SCREW |
| Парткод: | B223 1317 |
| Деталь: | Cover:Front Right |
| Парткод: | B223 1264 |
| Деталь: | Hinge - Cover Drum Stay |
| Парткод: | B223 1123 |
| Деталь: | Case - Remove Paper Dust |
| Парткод: | B238 2615 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 1012 |
| Деталь: | Inner Cover:Upper:Right |
| Парткод: | B223 1243 |
| Деталь: | Cover:Right:Front |
| Парткод: | B223 1271 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0451 3012N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw:3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | Harness:HDD:Power Source |
| Парткод: | B223 5736 |
| Деталь: | Harness:HDD:Raid:Upper |
| Парткод: | B223 5734 |
| Деталь: | Harness:HDD:Raid:Lower |
| Парткод: | B223 5735 |
| Деталь: | Total Counter:7FIG:24V |
| Парткод: | AX31 0045 |
| Деталь: | PCB:Controller |
| Парткод: | B224 5740 |
| Деталь: | PCB:DDR-DIMM:512MB |
| Парткод: | G108 5020 |
| Деталь: | HDD UNIT |
| Парткод: | B223 5090 |
| Деталь: | Fan Motor:MM40x10:NMB:1604KL-01W |
| Парткод: | B837 5700 |
| Деталь: | Bracket:Fan:Control Board |
| Парткод: | B223 5827 |
| Деталь: | Supporter:Lower |
| Парткод: | B223 5822 |
| Деталь: | Gasket:EGUN1-0205:L45 |
| Парткод: | B223 5864 |
| Деталь: | Gasket:EGUN1-0105:L240 |
| Парткод: | B223 5862 |
| Деталь: | Rack:Inner Back:Auxiliary:Left Lower |
| Парткод: | B223 5821 |
| Деталь: | Cover:SD-Card |
| Парткод: | B223 5824 |
| Деталь: | Interface Panel |
| Парткод: | B101 5993 |
| Деталь: | Grip:Rack:Left Lower |
| Парткод: | B223 5823 |
| Деталь: | Right Guide 1 |
| Парткод: | G108 5108 |
| Деталь: | Left Guide 1 |
| Парткод: | G108 5107 |
| Деталь: | SD-Card:Printer/Scanner |
| Парткод: | B837 5001 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw:3x14 |
| Парткод: | 0451 3014N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Clamp:EDS-0704L-V0 |
| Парткод: | 11 050 612 |
| Деталь: | Cover:Guide Plate:Exit |
| Парткод: | B223 2623 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0128 |
| Деталь: | Guide Plate:Exit |
| Парткод: | B223 2622 |
| Деталь: | Cover:Manual Feed Unit |
| Парткод: | B223 2621 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | Feed Roller - Manual Feed |
| Парткод: | AF03 1046 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Shaft:Feed |
| Парткод: | AA14 0777 |
| Деталь: | Stay:Feed |
| Парткод: | B223 2629 |
| Деталь: | Gear - 23Z |
| Парткод: | AB01 1387 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | AF03 0049 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3568 |
| Деталь: | Pick-up Arm - Manual Feed |
| Парткод: | G060 2932 |
| Деталь: | DC Solenoid:Pickup |
| Парткод: | B223 2632 |
| Деталь: | Spring:Release:Pickup |
| Парткод: | B223 2633 |
| Деталь: | Harness:Manual Feed |
| Парткод: | B223 2659 |
| Деталь: | Sheet:Guide:Exit |
| Парткод: | B223 2624 |
| Деталь: | Transport Roller:Exit:Duplex |
| Парткод: | B223 2619 |
| Деталь: | Support Stay:Arm |
| Парткод: | B223 2634 |
| Деталь: | Torsion Spring:27n |
| Парткод: | B223 2636 |
| Деталь: | Paper End Sensor |
| Парткод: | AW50 0035 |
| Деталь: | Arm:Manual Feed:Front |
| Парткод: | B223 2651 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2102 |
| Деталь: | Arm:Manual Feed:Short:Front |
| Парткод: | B223 2657 |
| Деталь: | Ground Plate:Reverse |
| Парткод: | B223 2607 |
| Деталь: | Guide Plate:Separator |
| Парткод: | B223 2609 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3016 |
| Деталь: | Bushing:Feed |
| Парткод: | G080 2682 |
| Деталь: | Ground Plate:Rear |
| Парткод: | B223 2606 |
| Деталь: | One-way Clutch |
| Парткод: | AA08 3014 |
| Деталь: | Magnetic clutch |
| Парткод: | AX20 2007 |
| Деталь: | Bracket:Arm:Manual Feed:Rear |
| Парткод: | B223 2637 |
| Деталь: | Arm:Manual Feed:Rear |
| Парткод: | B223 2652 |
| Деталь: | Arm:Manual Feed:Short:Rear |
| Парткод: | B223 2658 |
| Деталь: | Bushing - 6 6mm |
| Парткод: | A259 6754 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1416 |
| Деталь: | Gear:Z16 |
| Парткод: | B223 2608 |
| Деталь: | Shaft:Separator:Drive |
| Парткод: | AA14 0778 |
| Деталь: | Separation Roller - Manual Feed |
| Парткод: | AF03 2046 |
| Деталь: | TORQUE LIMITER |
| Парткод: | G080 2900 |
| Деталь: | Shaft:Separator:Driven:Assy |
| Парткод: | B180 2871 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3499 |
| Деталь: | SPRING |
| Парткод: | AA06 0872 |
| Деталь: | Arm:Tightener |
| Парткод: | B223 2681 |
| Деталь: | Idler Gear - 25z |
| Парткод: | AB01 1223 |
| Деталь: | Gear:Z31 |
| Парткод: | B223 2686 |
| Деталь: | Gear:25Z |
| Парткод: | B223 2683 |
| Деталь: | Gear:Z28 |
| Парткод: | B223 2689 |
| Деталь: | Drum Stay:Drive |
| Парткод: | B223 2696 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Screw - M3X4 |
| Парткод: | 0353 0040N |
| Деталь: | Tapping Screw:3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11 050 522 |
| Деталь: | Connector - 5P |
| Парткод: | 11 026 248 |
| Деталь: | Clamp:LES-0505 |
| Парткод: | 11 050 551 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Wire Clamp |
| Парткод: | A193 1766 |
| Деталь: | Clamp - Rear Wire |
| Парткод: | A193 1769 |
| Деталь: | Xenon Lamp |
| Парткод: | B223 1840 |
| Деталь: | Carriage:No.1:Assy |
| Парткод: | B180 1716 |
| Деталь: | 1st Mirror Holder |
| Парткод: | A193 1767 |
| Деталь: | 1st Mirror |
| Парткод: | AC03 0142 |
| Деталь: | Guide:High Voltage Supply Cord:Base |
| Парткод: | B180 1803 |
| Деталь: | Seal:Scanner:Frame:Base |
| Парткод: | B223 1824 |
| Деталь: | Harness:Xenon Lamp |
| Парткод: | B223 5218 |
| Деталь: | Rivet - Nrp345 |
| Парткод: | H020 2318 |
| Деталь: | Holder:Connector |
| Парткод: | B223 1786 |
| Деталь: | Original Sensor:H2-66 |
| Парткод: | AW01 0114 |
| Деталь: | Bracket:Original Sensor |
| Парткод: | B051 1814 |
| Деталь: | Inner cover |
| Парткод: | B180 1701 |
| Деталь: | Ground Plate:Stay:Lens |
| Парткод: | B223 1790 |
| Деталь: | Gasket:Rfsg-030100:75 |
| Парткод: | B223 1791 |
| Деталь: | Lens Unit |
| Парткод: | B223 1771 |
| Деталь: | Interface Cable:Scanner:LVDS:HF |
| Парткод: | B223 5225 |
| Деталь: | Duct:Scanner |
| Парткод: | B223 1825 |
| Деталь: | Seal:Duct:Front:Scanner |
| Парткод: | B223 1827 |
| Деталь: | Seal:Duct:Rear:Scanner |
| Парткод: | B223 1828 |
| Деталь: | Sheet:Fan:Duct:Scanner |
| Парткод: | B223 1826 |
| Деталь: | Fan Motor:15mm:24V |
| Парткод: | AX64 0164 |
| Деталь: | Original Sensor:H81.5 |
| Парткод: | AW01 0115 |
| Деталь: | Heater - 9W (120V) |
| Парткод: | A250 1821 |
| Деталь: | Heater - 9W (230V) |
| Парткод: | A250 1822 |
| Деталь: | Plate:Cable |
| Парткод: | B154 5879 |
| Деталь: | Original Sensor:H1-66 |
| Парткод: | AW01 0116 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 8 025 299 |
| Деталь: | CLAMP |
| Парткод: | 11 050 460 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11 050 508 |
| Деталь: | Connector:B2P5-VH-TW-R(LF)(SN) |
| Парткод: | 11 033 354 |
| Деталь: | CLAMP |
| Парткод: | 11 050 534 |
| Деталь: | Inner Cover:Duplex |
| Парткод: | B223 4534 |
| Деталь: | Inner Cover:Duplex:Rear |
| Парткод: | B223 4533 |
| Деталь: | Grip:Open And Close:Duplex Unit |
| Парткод: | B223 4579 |
| Деталь: | Hook:Stopper |
| Парткод: | B223 4590 |
| Деталь: | Tension Spring:Hook:Stopper |
| Парткод: | B223 4532 |
| Деталь: | Inner Cover:Sensor |
| Парткод: | B223 4482 |
| Деталь: | Tension Spring:Wire:180n |
| Парткод: | B223 4525 |
| Деталь: | Driven Roller:Dia16 |
| Парткод: | B223 4559 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B223 4538 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Guide Plate:Cover |
| Парткод: | B223 4531 |
| Деталь: | Cover:Duplex |
| Парткод: | B223 4540 |
| Деталь: | Spring:Cover:Manual Feed |
| Парткод: | B223 2665 |
| Деталь: | Cover:Manual Feed:Entrance |
| Парткод: | B223 2664 |
| Деталь: | Sheet:Cover:Duplex |
| Парткод: | B223 4539 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Feed Drive Shaft |
| Парткод: | B223 1189 |
| Деталь: | Grip Shaft |
| Парткод: | B223 1183 |
| Деталь: | Drive Joint |
| Парткод: | B223 1186 |
| Деталь: | Drum Stay:Drive Unit |
| Парткод: | B223 1354 |
| Деталь: | Gear - 33Z/44Z |
| Парткод: | AB01 7699 |
| Деталь: | Gear - 38Z |
| Парткод: | AB01 1258 |
| Деталь: | Timing Belt:40S3M162 |
| Парткод: | AA04 3585 |
| Деталь: | Timing Pulley - 28Z/30T |
| Парткод: | AB03 0781 |
| Деталь: | Gear - 32Z |
| Парткод: | AB01 1259 |
| Деталь: | Bracket:Paper Feed |
| Парткод: | B223 1180 |
| Деталь: | Magnetic Clutch - 32Z |
| Парткод: | AX20 0289 |
| Деталь: | Magnetic Clutch Bracket |
| Парткод: | B223 1187 |
| Деталь: | BUSHING - 6MM |
| Парткод: | GA08 0002 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Cushion:Stepper Motor |
| Парткод: | AA16 1164 |
| Деталь: | Stepper Motor DC24V |
| Парткод: | B223 1188 |
| Деталь: | Temperature & Humidity Sensor |
| Парткод: | AW14 0012 |
| Деталь: | Timing Belt - B40S2M118 |
| Парткод: | AA04 3601 |
| Деталь: | Timing Pulley - 27Z/40T |
| Парткод: | AB03 0744 |
| Деталь: | Bracket:Drive Unit:Registration |
| Парткод: | B223 1191 |
| Деталь: | Cushion - Stepper Motor |
| Парткод: | A232 4666 |
| Деталь: | Stepper Motor DC5.06V |
| Парткод: | B223 1350 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 0451 4008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | Tapping Screw - 4x10 |
| Парткод: | 0434 0100N |
| Деталь: | Supporter - Left No.2 |
| Парткод: | B223 2710 |
| Деталь: | Supporter - Left No.1 |
| Парткод: | B223 2705 |
| Деталь: | Rubber Foot Cover |
| Парткод: | B238 1066 |
| Деталь: | Heat Sink:Heater:NA |
| Парткод: | B223 2702 |
| Деталь: | Heat Sink:Heater:EU |
| Парткод: | B223 2703 |
| Деталь: | Cover:Connector:Heater |
| Парткод: | B223 1207 |
| Деталь: | Bracket:Paper Feed Unit |
| Парткод: | B223 1120 |
| Деталь: | Positioning Cap - Short |
| Парткод: | B223 2714 |
| Деталь: | Supporter - Right |
| Парткод: | B223 2715 |
| Деталь: | CUSHION |
| Парткод: | AA16 1163 |
| Деталь: | Rubber Foot:H5 |
| Парткод: | B101 1097 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 8 025 299 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Imaging Unit Assy C1c |
| Парткод: | B221 1851 |
| Деталь: | Imaging Unit Assy C1d |
| Парткод: | B223 1851 |
| Деталь: | Polygon Mirror Motor Board |
| Парткод: | B180 5445 |
| Деталь: | Harness:Polygon Mirror Motor |
| Парткод: | B223 5241 |
| Деталь: | Harness:Motor:Driver |
| Парткод: | B223 5243 |
| Деталь: | Polygon Mirror Motor |
| Парткод: | AX06 0286 |
| Деталь: | LOUVER |
| Парткод: | B223 1903 |
| Деталь: | Cover - Polygon Motor |
| Парткод: | B223 1882 |
| Деталь: | SCREW |
| Парткод: | B223 1907 |
| Деталь: | SHUTTER ASSY |
| Парткод: | B223 1885 |
| Деталь: | Cover - Upper |
| Парткод: | B223 1881 |
| Деталь: | Link:Shutter:2 |
| Парткод: | B223 1909 |
| Деталь: | Link:Shutter:1 |
| Парткод: | B223 1908 |
| Деталь: | Plate Nut:Link |
| Парткод: | B223 1989 |
| Деталь: | Torsion Spring:Link:2 |
| Парткод: | B223 1914 |
| Деталь: | Torsion Spring:Link:1 |
| Парткод: | B223 1913 |
| Деталь: | PCB Sync Detector |
| Парткод: | B238 5144 |
| Деталь: | Harness:LDB:1LD |
| Парткод: | B221 5236 |
| Деталь: | Harness:LDB:2LD |
| Парткод: | B223 5235 |
| Деталь: | Harness:Sync Detector |
| Парткод: | B223 5239 |
| Деталь: | Screw:Link:Shutter |
| Парткод: | B223 1988 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Binding Self-tapping Screw:3x10 |
| Парткод: | 0452 3010N |
| Деталь: | Harness:IOB:Main:Upper |
| Парткод: | B223 5302 |
| Деталь: | Harness:IOB:Main:Lower |
| Парткод: | B223 5300 |
| Деталь: | Harness:IOB:1bin |
| Парткод: | B223 5322 |
| Деталь: | Harness:IOB:Main:Middle |
| Парткод: | B223 5301 |
| Деталь: | Harness:IOB:Counter:EXP |
| Парткод: | B223 5325 |
| Деталь: | PCB:IOB |
| Парткод: | B223 5120 |
| Деталь: | Plate:Rack:Auxiliary:Right |
| Парткод: | B223 5816 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Harness Clamp - LWS 1316 |
| Парткод: | 11 050 489 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Harness Clamp - IWS-2218 |
| Парткод: | 11 050 490 |
| Деталь: | Bracket:Shaft:Side Plate:Front |
| Парткод: | B802 1773 |
| Деталь: | Knob:Misfeed Removal:T27 |
| Парткод: | B802 1777 |
| Деталь: | Tension Roller |
| Парткод: | B312 1615 |
| Деталь: | Timing Belt:40S3M189 |
| Парткод: | B802 1772 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Harness:Solenoid |
| Парткод: | B802 5790 |
| Деталь: | DC Solenoid:24V |
| Парткод: | B802 3811 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | TAPPING SCREW |
| Парткод: | AA14 3823 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Reverse Roller |
| Парткод: | A859 2241 |
| Деталь: | Torque Limiter - 53mnxm |
| Парткод: | A294 6700 |
| Деталь: | Shaft:Roller:Reverse |
| Парткод: | B802 2252 |
| Деталь: | Drum Stay:Guide:Reverse |
| Парткод: | B802 2225 |
| Деталь: | Gear:Z20 |
| Парткод: | B802 2253 |
| Деталь: | Guide:Reverse:Open And Close |
| Парткод: | B802 2222 |
| Деталь: | Decal:Display:Misfeed Removal:P2 |
| Парткод: | B802 6014 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | Roller:Reverse Exit:Driven |
| Парткод: | B802 2285 |
| Деталь: | Shaft:Reverse:Drive:Press Fit |
| Парткод: | B802 2231 |
| Деталь: | Guide:Reverse:Open And Close:Behind |
| Парткод: | B802 2227 |
| Деталь: | Cushion - Bin Solenoid Lever |
| Парткод: | A458 2251 |
| Деталь: | Stopper Pawl:Paper Feed |
| Парткод: | B802 2111 |
| Деталь: | Bushing:6x8x5 |
| Парткод: | AA08 0265 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0843 |
| Деталь: | Lever:Stopper Pawl |
| Парткод: | B802 2115 |
| Деталь: | Spring:Pressure |
| Парткод: | AA06 3919 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Screw - M3X4 |
| Парткод: | 0353 0040N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Parallel Pin - 2x12 |
| Парткод: | 0632 0120G |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Gear:18Z |
| Парткод: | B223 4459 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Timing Belt:30S2M216 |
| Парткод: | AA04 3969 |
| Деталь: | Gear:Pulley:Z18/T23 |
| Парткод: | B223 4458 |
| Деталь: | Spacer:Idler |
| Парткод: | B223 4456 |
| Деталь: | Timing Pulley:23T |
| Парткод: | B223 4464 |
| Деталь: | SCREW |
| Парткод: | B238 4483 |
| Деталь: | Inner Cover:Exit:Front |
| Парткод: | B223 4437 |
| Деталь: | Inner Cover:Exit:Rear |
| Парткод: | B223 4438 |
| Деталь: | Harness:IOB:Paper Exit Unit:C |
| Парткод: | B223 4439 |
| Деталь: | Bracket:Sensor |
| Парткод: | B223 4426 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Transport Roller:Dia18 |
| Парткод: | B223 4454 |
| Деталь: | Guide Plate:Upper Right |
| Парткод: | B223 4461 |
| Деталь: | BUSHING - M4 |
| Парткод: | H053 2208 |
| Деталь: | Tension Spring:1.3n |
| Парткод: | B223 4452 |
| Деталь: | Bracket:Gear:Coupling |
| Парткод: | B223 4447 |
| Деталь: | Gear:Z14/Z40 |
| Парткод: | B223 4451 |
| Деталь: | Gear:Z20/Z32 |
| Парткод: | B223 4467 |
| Деталь: | Bracket:Stepper Motor:Gate |
| Парткод: | B223 4444 |
| Деталь: | Stepper Motor:DC24V 70.2W |
| Парткод: | B223 4441 |
| Деталь: | STOPPER |
| Парткод: | B223 4468 |
| Деталь: | Gear:Z14 |
| Парткод: | B223 4450 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0453 3006N |
| Деталь: | Binding Self Tapping Screw:3x10 |
| Парткод: | 0453 3010N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Retaining Ring - 3m |
| Парткод: | 8 050 092 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Used Toner Sensor Bracket |
| Парткод: | B223 6502 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Used Toner Sensor Feeler |
| Парткод: | B223 6503 |
| Деталь: | Harness - Used Toner Sensor |
| Парткод: | B238 5313 |
| Деталь: | Bracket:Fan |
| Парткод: | B223 1331 |
| Деталь: | Fan Motor - Mm60 DC24V |
| Парткод: | B223 1332 |
| Деталь: | Harness:IOB:Fan Motor |
| Парткод: | B223 5311 |
| Деталь: | Collection Bottle Rail |
| Парткод: | B223 6496 |
| Деталь: | Bracket - Main Switch Handle |
| Парткод: | B238 5821 |
| Деталь: | Slide Switch Cover |
| Парткод: | B238 5824 |
| Деталь: | Power Source Switch Link |
| Парткод: | B238 5825 |
| Деталь: | Cleaning Unit Rail |
| Парткод: | B223 6198 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screr:Fan |
| Парткод: | 8 025 308 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Decal:Caution:Original:5-lang |
| Парткод: | B652 2379 |
| Деталь: | STEPPED SCREW |
| Парткод: | A859 7211 |
| Деталь: | Screw - M4 |
| Парткод: | A548 6121 |
| Деталь: | Cover:Front |
| Парткод: | B802 4411 |
| Деталь: | Decal:Display:Misfeed Removal:P1 |
| Парткод: | B802 6013 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Sound Proofing Material:Cover:Rear |
| Парткод: | B802 4712 |
| Деталь: | Cover:Rear |
| Парткод: | B802 4511 |
| Деталь: | Stay:Original Table:Contact Point |
| Парткод: | B802 2551 |
| Деталь: | Stopper:Original Table |
| Парткод: | B802 2581 |
| Деталь: | Side Fence |
| Парткод: | B802 2526 |
| Деталь: | Decal - Original Table |
| Парткод: | B789 6031 |
| Деталь: | Original Table:Face Front |
| Парткод: | B802 2522 |
| Деталь: | Slider:Side Fence |
| Парткод: | B802 2536 |
| Деталь: | Spring Plate:Side Fence |
| Парткод: | B802 2532 |
| Деталь: | Decal:Side Fence |
| Парткод: | B802 6011 |
| Деталь: | Spring Plate:0.2t |
| Парткод: | B802 2571 |
| Деталь: | Spring Plate - Pressure Roller |
| Парткод: | A858 4676 |
| Деталь: | ROLLER DRIVEN |
| Парткод: | A858 4671 |
| Деталь: | PHOTO REFIECTION SENSOR:EXIT |
| Парткод: | GW01 0007 |
| Деталь: | Guide:Original Insert |
| Парткод: | B802 2541 |
| Деталь: | Harness:Original Table |
| Парткод: | B802 5750 |
| Деталь: | Photo Refiection Sensor |
| Парткод: | AW01 0129 |
| Деталь: | Plate:Contact Point |
| Парткод: | B802 2562 |
| Деталь: | Original Table |
| Парткод: | B802 2512 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0513 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Gear:Sensor:Turn |
| Парткод: | AB01 0088 |
| Деталь: | Roller:Ferrite Core:Assy |
| Парткод: | B223 4235 |
| Деталь: | Fusing Belt:Dia60:Adhesion |
| Парткод: | B223 4221 |
| Деталь: | Bushing:Heat Roller |
| Парткод: | AE03 1046 |
| Деталь: | Ball Bearing:Dia12xdia21x7 |
| Парткод: | AE03 0069 |
| Деталь: | Hot Roller:Dia35 |
| Парткод: | AE01 0059 |
| Деталь: | Ball Bearing:Dia17xdia26x5 |
| Парткод: | AE03 0071 |
| Деталь: | Pressure Roller:Dia40 |
| Парткод: | AE02 0115 |
| Деталь: | Roller:Belt Tensioner:Dia12 |
| Парткод: | B223 4226 |
| Деталь: | Gear:Hot Roller |
| Парткод: | AB01 2044 |
| Деталь: | Spacer:Heat Roller |
| Парткод: | B223 4233 |
| Деталь: | Gear:Turn:Ferrite Core:Z16 |
| Парткод: | AB01 1249 |
| Деталь: | Gear:Pressure Roller |
| Парткод: | AB01 2045 |
| Деталь: | Gear:Drive:Fusing |
| Парткод: | AB01 7703 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | AA14 3526 |
| Деталь: | Bushing:Fusing Sub-unit |
| Парткод: | AE03 1065 |
| Деталь: | Compression Spring:Belt Tensioner |
| Парткод: | AA06 3954 |
| Деталь: | Gear:Idler:Pressure Roller |
| Парткод: | AB01 2051 |
| Деталь: | Rear Bushing - Oil Supply Roller |
| Парткод: | AE03 1062 |
| Деталь: | Bracket:Oil Supply Roller |
| Парткод: | B223 4181 |
| Деталь: | Compression Spring:Oil Supply Roller |
| Парткод: | AA06 3953 |
| Деталь: | Cleaning Roller - Oil Supply Roller |
| Парткод: | AE04 0066 |
| Деталь: | Oil Supply Roller |
| Парткод: | AE04 0065 |
| Деталь: | Front Bushing - Oil Supply Roller |
| Парткод: | AE03 1061 |
| Деталь: | Encoder:Ferrite Core:Change |
| Парткод: | B223 4232 |
| Деталь: | Gear:Turn:Sensor |
| Парткод: | AB01 0118 |
| Деталь: | Screw:Positioning Control |
| Парткод: | B223 4072 |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Retaining Ring C - M10 |
| Парткод: | 0725 0100E |
| Деталь: | Retaining Ring C - M17 |
| Парткод: | 0725 0170E |
| Деталь: | Retaining Ring C - M12 |
| Парткод: | 0725 0120E |
| Деталь: | Sheet - Transport Sub-unit |
| Парткод: | B223 2677 |
| Деталь: | Guide Plate - Vertical Transport |
| Парткод: | B223 2675 |
| Деталь: | BUSHING - M4 |
| Парткод: | G060 2652 |
| Деталь: | Spring - 11n |
| Парткод: | B223 2676 |
| Деталь: | Vertical Transport Roller |
| Парткод: | AF02 0646 |
| Деталь: | Guide Plate:Transport Unit:Exit |
| Парткод: | B223 2648 |
| Деталь: | Spring:Pressure:5n |
| Парткод: | B223 2649 |
| Деталь: | Roller:Driven:Dia16 |
| Парткод: | B223 2641 |
| Деталь: | Spacer:Wire:Stopper |
| Парткод: | B223 4522 |
| Деталь: | Harness:Duplex Md |
| Парткод: | B223 4587 |
| Деталь: | Shaft:Pulley:Wire |
| Парткод: | B223 4594 |
| Деталь: | Pulley:DIA13 |
| Парткод: | B223 4595 |
| Деталь: | Bracket:Shaft:Pulley:Wire |
| Парткод: | B223 4596 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Philips Pan Head Screw - M4x6 |
| Парткод: | 8 010 149 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Clamp:Lwss-0504 |
| Парткод: | 11 050 568 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11 050 508 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Screw:A |
| Парткод: | AA14 3807 |
| Деталь: | Guide Plate:Upper:Gate |
| Парткод: | B223 4483 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Bracket:Sensor:Entrance |
| Парткод: | B223 4566 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Driven Roller:Dia16 |
| Парткод: | B223 4559 |
| Деталь: | Tension Spring:Driven Roller |
| Парткод: | B223 4560 |
| Деталь: | Bushing:Dia4 |
| Парткод: | B223 4552 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Reverse Roller:Feed Paper Again |
| Парткод: | B223 4537 |
| Деталь: | Reverse Roller Gear |
| Парткод: | AB01 4161 |
| Деталь: | Tightener |
| Парткод: | B223 4562 |
| Деталь: | SHOULDER SCREW |
| Парткод: | B044 1847 |
| Деталь: | Spring:Tightener |
| Парткод: | B223 4564 |
| Деталь: | Timing Belt:30S2M268 |
| Парткод: | B223 4526 |
| Деталь: | Pulley:T30 |
| Парткод: | B223 4586 |
| Деталь: | Stepper Motor:DC4.29V 1.7W |
| Парткод: | B223 4572 |
| Деталь: | Rubber Bushing - 6 45hs |
| Парткод: | AA10 1021 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B223 4575 |
| Деталь: | Gear:Pulley:Z24/T40 |
| Парткод: | B223 4571 |
| Деталь: | Timing Belt:30S2M128 |
| Парткод: | B223 4573 |
| Деталь: | COLLAR |
| Парткод: | B044 1825 |
| Деталь: | Guide Plate:Right |
| Парткод: | B223 4501 |
| Деталь: | Stopper Screw - M3 |
| Парткод: | 58 403 022 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Screw-m3x10 |
| Парткод: | 0353 0100N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Clamp:LES-0505 |
| Парткод: | 11 050 551 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | Tension Spring:Arm:Duplex |
| Парткод: | AA06 1013 |
| Деталь: | Arm:Front |
| Парткод: | B223 4321 |
| Деталь: | Timing Belt:30S2M182 |
| Парткод: | B223 4512 |
| Деталь: | Timing Belt:30S2M234 |
| Парткод: | B223 4536 |
| Деталь: | Timing Belt:30S2M312 |
| Парткод: | B223 4511 |
| Деталь: | Roller Clutch:T24 |
| Парткод: | B223 4529 |
| Деталь: | Pulley:T35/T33 |
| Парткод: | B223 4544 |
| Деталь: | Pulley:T26/T24 |
| Парткод: | B223 4527 |
| Деталь: | Roller Clutch:T26 |
| Парткод: | B223 4535 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Transport Roller:No.1 |
| Парткод: | B223 4513 |
| Деталь: | Transport Roller:No.2 |
| Парткод: | B223 4543 |
| Деталь: | Guide Plate:Left Lower |
| Парткод: | B223 4502 |
| Деталь: | Roller Clutch:T24 |
| Парткод: | B223 4514 |
| Деталь: | Arm:Rear |
| Парткод: | B223 4320 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Harness:Registration Sensor |
| Парткод: | B802 5810 |
| Деталь: | Bracket:Guide:Paper Feed:Lower |
| Парткод: | B802 3381 |
| Деталь: | Ground Plate:Roller:Scanning |
| Парткод: | B802 3147 |
| Деталь: | Discharge Brush:Exit:Small |
| Парткод: | G052 4892 |
| Деталь: | Spring Plate |
| Парткод: | B802 3145 |
| Деталь: | PHOTO REFIECTION SENSOR:EXIT |
| Парткод: | GW01 0007 |
| Деталь: | Shielding Plate:Sensor |
| Парткод: | B802 3833 |
| Деталь: | Bracket:Registration Sensor |
| Парткод: | B802 3832 |
| Деталь: | Roller:Scanning:Entrance |
| Парткод: | B802 3231 |
| Деталь: | Roller:Scanning:Exit |
| Парткод: | B802 3251 |
| Деталь: | Timing Pulley:T33/T24 |
| Парткод: | B802 3234 |
| Деталь: | Timing Pulley:T33 |
| Парткод: | B802 3252 |
| Деталь: | Damper - Junction Gate Solenoid |
| Парткод: | A697 2102 |
| Деталь: | Timing Pulley:T33 |
| Парткод: | B802 3233 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Ball Bearing - 6x12x4 Mm |
| Парткод: | 7 413 506 |
| Деталь: | Ball Bearimg - 6x12x4 Mm |
| Парткод: | 7 403 506 |
| Деталь: | Pin - 2x10mm |
| Парткод: | 0632 0100G |
| Деталь: | Edge Saddle - Eds-0607l |
| Парткод: | 11 050 514 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Developer:BK |
| Парткод: | B230 9640 |
| Деталь: | Developer:C |
| Парткод: | B230 9660 |
| Деталь: | Developer:M |
| Парткод: | B230 9670 |
| Деталь: | Developer:Y |
| Парткод: | B230 9680 |
| Деталь: | Development Unit:BK |
| Парткод: | B223 3013 |
| Деталь: | Development Unit:M |
| Парткод: | B223 3023 |
| Деталь: | Development Unit:C |
| Парткод: | B223 3033 |
| Деталь: | Development Unit:Y |
| Парткод: | B223 3043 |
| Деталь: | CLEANING UNIT |
| Парткод: | B223 6023 |
| Деталь: | Drum Unit:BK |
| Парткод: | B223 2244 |
| Деталь: | Drum Unit:M |
| Парткод: | B223 2245 |
| Деталь: | Drum Unit:C |
| Парткод: | B223 2246 |
| Деталь: | Drum Unit:Y |
| Парткод: | B223 2247 |
| Деталь: | Intermediate Transfer Section:Servi |
| Парткод: | B223 6032 |
| Деталь: | PCU:BK |
| Парткод: | B223 2204 |
| Деталь: | PCU:C |
| Парткод: | B223 2205 |
| Деталь: | PCU:M |
| Парткод: | B223 2206 |
| Деталь: | PCU:Y |
| Парткод: | B223 2207 |
| Деталь: | Collection Bottle:Exp:Ass |
| Парткод: | B223 6542 |
| Деталь: | Image Transfer Belt |
| Парткод: | B223 6130 |
| Деталь: | Decal - Paper Size |
| Парткод: | B238 2524 |
| Деталь: | Cover - Right |
| Парткод: | B238 1380 |
| Деталь: | Cloth Holder |
| Парткод: | B065 1371 |
| Деталь: | Operating Instructions Holder |
| Парткод: | B223 1248 |
| Деталь: | Rivet - 5 |
| Парткод: | G038 1299 |
| Деталь: | Cloth - DF Exposure Glass |
| Парткод: | B065 1374 |
| Деталь: | Power Supply Code:125V 15A NA |
| Парткод: | 11 500 373 |
| Деталь: | Power Supply Code:250V:10A:EU |
| Парткод: | 11 500 377 |
| Деталь: | Ferrite Core - RFC-5 |
| Парткод: | 16 071 715 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Overflow Feeler |
| Парткод: | B238 4987 |
| Деталь: | Overflow Feeler Shaft |
| Парткод: | B238 4985 |
| Деталь: | EXIT ROLLER |
| Парткод: | B223 4453 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Ground Plate:Bracket:Sensor |
| Парткод: | B223 4427 |
| Деталь: | Discharge Brush:Exit |
| Парткод: | B223 4491 |
| Деталь: | Guide Plate:Upper Left |
| Парткод: | B223 4421 |
| Деталь: | BUSHING - M4 |
| Парткод: | H053 2208 |
| Деталь: | Transport Roller:Auxiliary |
| Парткод: | B223 4455 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Timing Belt:30S2M160 |
| Парткод: | AA04 3968 |
| Деталь: | Gear:Pulley:Z27/T22 |
| Парткод: | B223 4457 |
| Деталь: | Timing Pulley:22T |
| Парткод: | B223 4463 |
| Деталь: | Roller:Auxiliary:Driven:Dia16:pFA |
| Парткод: | B223 4435 |
| Деталь: | Shaft:Pressure:Auxiliary |
| Парткод: | B223 4493 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0156 |
| Деталь: | Compression Spring - Driven Roller |
| Парткод: | B238 4458 |
| Деталь: | Roller:Guide:pFA |
| Парткод: | B223 4428 |
| Деталь: | Guide Plate:Lower |
| Парткод: | B223 4488 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0567 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0566 |
| Деталь: | Spring Plate - Exit Roller Outer |
| Парткод: | B238 4436 |
| Деталь: | Spring Plate - Exit Roller |
| Парткод: | B223 4436 |
| Деталь: | Sensor bracket |
| Парткод: | B238 4454 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0127 |
| Деталь: | Stay:Protect |
| Парткод: | B223 4442 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Screw-m3x10 |
| Парткод: | 0353 0100N |
| Деталь: | Binding Self-tapping Screw:3x10 |
| Парткод: | 0452 3010N |
| Деталь: | Retaining Ring - 3m |
| Парткод: | 8 050 092 |
| Деталь: | Toner Supply Drive Unit |
| Парткод: | B223 3400 |
| Деталь: | PCB:RFID:RW |
| Парткод: | B238 5051 |
| Деталь: | Rfid Ground Plate |
| Парткод: | B223 3470 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Shaft:Drive:Drive Unit:CM |
| Парткод: | B223 3426 |
| Деталь: | Shaft:Drive:Drive Unit:BKY |
| Парткод: | B223 3424 |
| Деталь: | Timing Belt:Toner Bottle |
| Парткод: | B223 3441 |
| Деталь: | Pulley:Toner Bottle:YC |
| Парткод: | B223 3461 |
| Деталь: | Pulley:Toner Bottle:CM |
| Парткод: | B223 3462 |
| Деталь: | Gear:Magnetic Clutch:Y |
| Парткод: | B223 3464 |
| Деталь: | Magnetic Clutch - 0.25n.m YCM |
| Парткод: | B223 3457 |
| Деталь: | Magnetic Clutch - 0.25n.m BK |
| Парткод: | B223 3455 |
| Деталь: | Spring:Drive Unit:Toner Bottle |
| Парткод: | B223 3428 |
| Деталь: | Gear:Toner Bottle:DRIVE |
| Парткод: | B223 3463 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Positioning Guide - Front |
| Парткод: | B223 6311 |
| Деталь: | Positioning Guide - Rear |
| Парткод: | B223 6312 |
| Деталь: | CUSHION |
| Парткод: | B223 6315 |
| Деталь: | TENSION SPRING |
| Парткод: | B238 2676 |
| Деталь: | Registration Roller Bushing |
| Парткод: | B238 2675 |
| Деталь: | Registration Roller - Driven |
| Парткод: | B238 2661 |
| Деталь: | Gear - 18Z |
| Парткод: | B238 2657 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Registration Roller Knob |
| Парткод: | B223 2558 |
| Деталь: | Registration Roller - Drive |
| Парткод: | B238 2652 |
| Деталь: | Gear - 16Z |
| Парткод: | B238 2655 |
| Деталь: | Gear - 30Z |
| Парткод: | B238 2656 |
| Деталь: | Cleaner Bracket |
| Парткод: | B238 2670 |
| Деталь: | Cover - Remove Paper Dust |
| Парткод: | B238 2622 |
| Деталь: | STAY |
| Парткод: | B238 2621 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Harness:Registration Sensor |
| Парткод: | B223 2599 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3404 |
| Деталь: | Link:Stopper |
| Парткод: | B223 4523 |
| Деталь: | Guide Plate:Registration:Right |
| Парткод: | B223 2570 |
| Деталь: | Registration Guide Plate - Left |
| Парткод: | B238 2612 |
| Деталь: | Wire:Stopper:Dia1.5 |
| Парткод: | B223 4524 |
| Деталь: | GUIDE PLATE |
| Парткод: | B223 2835 |
| Деталь: | Guide Plate No.2 |
| Парткод: | B223 2840 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Clamp - RFC-14V0 |
| Парткод: | 11 050 643 |
| Деталь: | Fusing Section:NA:Assy |
| Парткод: | B223 0211 |
| Деталь: | Fusing Section:EU:Assy |
| Парткод: | B223 0212 |
| Деталь: | Heater:120V:500W |
| Парткод: | AX43 0156 |
| Деталь: | Heater:230V:500W |
| Парткод: | AX43 0157 |
| Деталь: | Thermistor:Fusing:Assy |
| Парткод: | B223 4172 |
| Деталь: | Thermistor:Pressuer:Assy |
| Парткод: | B223 4177 |
| Деталь: | Thermostat:149c/150c |
| Парткод: | B223 4162 |
| Деталь: | Screw - M3x8 |
| Парткод: | 0954 3008N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | DRIVE UNIT |
| Парткод: | B223 1177 |
| Деталь: | Duct:Rear:1 |
| Парткод: | B223 1236 |
| Деталь: | Fan Motor:DC24V 2.4W |
| Парткод: | AX64 0179 |
| Деталь: | Duct:Rear:3 |
| Парткод: | B223 1238 |
| Деталь: | Duct:Rear:2 |
| Парткод: | B223 1237 |
| Деталь: | Brushless Motor DC24V8W |
| Парткод: | AX05 0249 |
| Деталь: | Holder:Positioning Sensor |
| Парткод: | B223 1144 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Harness:IOB:Connecting:Drum:Sensor |
| Парткод: | B223 5350 |
| Деталь: | Brushless Motor:DC24V 25W |
| Парткод: | AX06 0308 |
| Деталь: | Snap Ring - M6 |
| Парткод: | AA10 0015 |
| Деталь: | Holder:Magnetic Clutch |
| Парткод: | B223 1370 |
| Деталь: | Magnetic Clutch:0.5n.m |
| Парткод: | AX20 0300 |
| Деталь: | Shaft:Development |
| Парткод: | B223 1148 |
| Деталь: | Gear - 23Z |
| Парткод: | AB01 0367 |
| Деталь: | Magnetic Clutch:0.5n.m |
| Парткод: | AX20 0299 |
| Деталь: | DC Motor 24V |
| Парткод: | B223 1199 |
| Деталь: | Brushless Motor:Drive:Paper Feed |
| Парткод: | GX06 0015 |
| Деталь: | Guide:Harness |
| Парткод: | B223 1364 |
| Деталь: | Gear:Development:NO.4 |
| Парткод: | AB01 0368 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Screw - M3X16 |
| Парткод: | 0360 3016N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Plate:Cable |
| Парткод: | B154 5879 |
| Деталь: | Interface Cable:Scanner:LVDS:HF |
| Парткод: | B223 5225 |
| Деталь: | Harness:LD Unit:LD-Data:1LD |
| Парткод: | B221 5247 |
| Деталь: | Harness:IPU:LD-Data:2LD |
| Парткод: | B223 5246 |
| Деталь: | Harness:IPU:Sync Detector:Mirror |
| Парткод: | B223 5248 |
| Деталь: | Harness:LD Unit:LD-Signal:1LD |
| Парткод: | B221 5245 |
| Деталь: | Harness:IPU:LD-Signal:2LD |
| Парткод: | B223 5244 |
| Деталь: | Harness:Power Supply Unit:C1 |
| Парткод: | B223 5347 |
| Деталь: | PCB:IPU |
| Парткод: | B223 5725 |
| Деталь: | Hinge:Panel:Control Board |
| Парткод: | B223 5812 |
| Деталь: | Harness:Connecting:BCU:SIO |
| Парткод: | B223 5321 |
| Деталь: | Harness:EGB:TM/P:Sensor |
| Парткод: | G133 5328 |
| Деталь: | Harness:IOB:BCU |
| Парткод: | B223 5320 |
| Деталь: | Bracket:BCU |
| Парткод: | B223 5807 |
| Деталь: | PCB:BCU |
| Парткод: | B223 5113 |
| Деталь: | Harness:MB:OPU |
| Парткод: | B223 5327 |
| Деталь: | PCB:MB:AP-C1 |
| Парткод: | B223 5747 |
| Деталь: | Supporter:Rapi:Upper |
| Парткод: | B223 5808 |
| Деталь: | Supporter:Rapi:Lower |
| Парткод: | B223 5809 |
| Деталь: | Interface Panel |
| Парткод: | B101 5993 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Clamp - LES-1017 |
| Парткод: | 11 050 521 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Harness Clamp - IWS-2218 |
| Парткод: | 11 050 490 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | PCS-20S-V0 |
| Парткод: | 11 050 642 |
| Деталь: | EEPROM:BR24L64-W |
| Парткод: | 14 076 362 |
| Деталь: | Paper Feed:Unit |
| Парткод: | B802 4311 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Gear:Z19 |
| Парткод: | B802 4357 |
| Деталь: | Timing Pulley:Gear:T19/Z22 |
| Парткод: | B802 4358 |
| Деталь: | Roller:Pickup |
| Парткод: | B802 4361 |
| Деталь: | Pickup Collar |
| Парткод: | B387 2163 |
| Деталь: | Timing Pulley:T21 |
| Парткод: | B802 4372 |
| Деталь: | Timing Belt:40S2M130 |
| Парткод: | AA04 3328 |
| Деталь: | Shaft:Pickup |
| Парткод: | B802 4352 |
| Деталь: | Bracket:Pickup |
| Парткод: | B802 4355 |
| Деталь: | Cushion:Pickup |
| Парткод: | B802 4359 |
| Деталь: | Drive Shaft - Paper Feed Belt |
| Парткод: | A859 2112 |
| Деталь: | Roller - Paper Feed Belt |
| Парткод: | B387 2113 |
| Деталь: | Spring:Belt:Paper Feed:8n |
| Парткод: | B386 3320 |
| Деталь: | Bracket:Paper Feed Belt |
| Парткод: | B802 4333 |
| Деталь: | Collar:Shaft |
| Парткод: | B802 4326 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | SPACER |
| Парткод: | AA13 2013 |
| Деталь: | Compression Spring:Paper Feed:Joint |
| Парткод: | AA06 3435 |
| Деталь: | Bushing - 8mm |
| Парткод: | A628 1225 |
| Деталь: | Paper Feed Belt Roller |
| Парткод: | B789 2114 |
| Деталь: | Feed Belt |
| Парткод: | A806 1295 |
| Деталь: | Shaft:Drive |
| Парткод: | B802 4322 |
| Деталь: | Torsion Spring:Pickup:Pressure |
| Парткод: | AA06 6376 |
| Деталь: | HOLDER |
| Парткод: | B802 4323 |
| Деталь: | Lever:Pickup:Release |
| Парткод: | B802 4325 |
| Деталь: | Gear:Z20 |
| Парткод: | B802 4328 |
| Деталь: | Drum Stay:Upper:Front |
| Парткод: | B802 4228 |
| Деталь: | Drum Stay:Upper:Inner Back |
| Парткод: | B802 4227 |
| Деталь: | Sheet:Guide:Upper |
| Парткод: | B802 4229 |
| Деталь: | Spring Plate:Upper |
| Парткод: | B802 4224 |
| Деталь: | Guide:Upper |
| Парткод: | B802 4222 |
| Деталь: | Bushing:DIA6 |
| Парткод: | AA08 0288 |
| Деталь: | Driven Roller:Pull Out |
| Парткод: | B802 4295 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3441 |
| Деталь: | Bracket:Driven Roller:Pull Out |
| Парткод: | B802 4282 |
| Деталь: | Ground Plate:Driven Roller:Pull Out |
| Парткод: | B802 4292 |
| Деталь: | Discharge Brush:Exit:Small |
| Парткод: | G052 4892 |
| Деталь: | GROUND PLATE |
| Парткод: | B802 4265 |
| Деталь: | Sheet:Driven Roller:Pull Out |
| Парткод: | B802 4225 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | Pin - 2x10mm |
| Парткод: | 0632 0100G |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Ball Bearing - 6x12x4 Mm |
| Парткод: | 7 413 506 |
| Деталь: | Bracket:Sw:Dehumidifier:Heater:Exp |
| Парткод: | B223 5857 |
| Деталь: | Duct:Rear:Lower |
| Парткод: | B223 1239 |
| Деталь: | Gasket:Etnw100-00505:L90 |
| Парткод: | B223 5861 |
| Деталь: | Power Supply Unit:494W:DOM/NA |
| Парткод: | AZ24 0109 |
| Деталь: | Power Supply Unit:494W:EU/AA:APO-C1 |
| Парткод: | AZ24 0110 |
| Деталь: | Harness:PSU:JIGU |
| Парткод: | B223 5336 |
| Деталь: | Harness:Power Supply Unit |
| Парткод: | B223 5345 |
| Деталь: | Harness:PSU:SW:NA |
| Парткод: | B223 5332 |
| Деталь: | Harness:AC:IH:Power Supply Unit |
| Парткод: | B223 5331 |
| Деталь: | Harness:AC:IH:Power Supply Unit:EU |
| Парткод: | B223 5338 |
| Деталь: | Power Pack:CB:APO-C/P:-80mic |
| Парткод: | AZ32 0165 |
| Деталь: | Harness:AC:Inlet |
| Парткод: | B223 5333 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Screw - M4X8 |
| Парткод: | 0954 4008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Clamp - EDS-1710L-V0 |
| Парткод: | 11 050 614 |
| Деталь: | Clamp:EDS-1010L-V0 |
| Парткод: | 11 050 613 |
| Деталь: | Connector - 54679-1615 |
| Парткод: | 11 028 502 |
| Деталь: | Rocker Switch:Sddje13200 |
| Парткод: | 12 042 570 |
| Деталь: | Clamp:EDS-0704L-V0 |
| Парткод: | 11 050 612 |
| Деталь: | Paper Tray Unit No.2 |
| Парткод: | B223 2900 |
| Деталь: | Link - Paper Size Sensor |
| Парткод: | B223 2910 |
| Деталь: | SPACER |
| Парткод: | B223 2911 |
| Деталь: | Decal - Paper Set Direction No.2 |
| Парткод: | B238 2523 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B223 2940 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3006 |
| Деталь: | Ground Plate - Paper Tray No.2 |
| Парткод: | B223 2919 |
| Деталь: | Cover - Paper Tray No.2 |
| Парткод: | B223 2946 |
| Деталь: | Paper Tray Grip |
| Парткод: | B223 2860 |
| Деталь: | Decal - Grip |
| Парткод: | B238 2527 |
| Деталь: | Lever - Release Inner |
| Парткод: | B223 2862 |
| Деталь: | Tension Spring:Grip |
| Парткод: | AA06 1014 |
| Деталь: | Release Shaft |
| Парткод: | B223 2863 |
| Деталь: | Grip Holder |
| Парткод: | B223 2861 |
| Деталь: | External Circlip - Mm8 |
| Парткод: | A222 2724 |
| Деталь: | Lever - Release Outer |
| Парткод: | B223 2864 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | END FENCE |
| Парткод: | B223 2912 |
| Деталь: | Front Side Fence |
| Парткод: | B223 2920 |
| Деталь: | Stopper Lever - Front |
| Парткод: | B223 2923 |
| Деталь: | Spring Plate - Release Lever |
| Парткод: | B004 2923 |
| Деталь: | Plate - Side Fence Right |
| Парткод: | B223 2935 |
| Деталь: | Plate - Side Fence |
| Парткод: | B223 2934 |
| Деталь: | Gear - 16Z |
| Парткод: | B223 2936 |
| Деталь: | Rise No.1 Shaft |
| Парткод: | B223 2865 |
| Деталь: | Rise Lever |
| Парткод: | B223 2918 |
| Деталь: | Rear Side Fence |
| Парткод: | B223 2930 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A267 2860 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Decal - Side Fence Rear |
| Парткод: | B223 2873 |
| Деталь: | Tension Spring:Side Fence:Rear |
| Парткод: | AA06 1003 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0450 4008N |
| Деталь: | Binding Self Tapping Screw:3x8 |
| Парткод: | 0453 3008N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | SCREW |
| Парткод: | B223 1317 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3568 |
| Деталь: | Safety Switch Bracket |
| Парткод: | B223 5813 |
| Деталь: | Bracket - Safety Switch Lever |
| Парткод: | B223 5814 |
| Деталь: | DC Motor:Shutter:Assy |
| Парткод: | B223 1213 |
| Деталь: | DC Motor Bracket |
| Парткод: | B223 1212 |
| Деталь: | TORSION SPRING |
| Парткод: | B223 1224 |
| Деталь: | Shutter Link |
| Парткод: | B223 1225 |
| Деталь: | Sensor Link Bracket |
| Парткод: | B223 1221 |
| Деталь: | Harness:IOB:Connecting:TM/P:Sensor |
| Парткод: | B223 5309 |
| Деталь: | Density Sensor:Assy |
| Парткод: | B223 5876 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0151 |
| Деталь: | Hook:Solenoid:Sensor:TM |
| Парткод: | B238 5867 |
| Деталь: | DC Solenoid DC24V |
| Парткод: | B238 5875 |
| Деталь: | DENSITY SENSOR |
| Парткод: | B223 6395 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Harness:IOB:LD Unit:Shutter |
| Парткод: | B223 5313 |
| Деталь: | Sensor Shutter Bracket |
| Парткод: | B223 1227 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw:M3x25 |
| Парткод: | 0451 3025N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Screw - M2.5X4 |
| Парткод: | 0312 5040N |
| Деталь: | Clamp:EDS-0704L-V0 |
| Парткод: | 11 050 612 |
| Деталь: | Screw:M3X25 |
| Парткод: | 0353 0250N |
| Деталь: | Switch - V-5F930DN |
| Парткод: | 12 042 709 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | Operation Panel:NA |
| Парткод: | B224 1411 |
| Деталь: | Operation Panel:EU |
| Парткод: | B224 1412 |
| Деталь: | Spacer - Keytop |
| Парткод: | B238 1547 |
| Деталь: | Keytop - Counter |
| Парткод: | B238 1511 |
| Деталь: | Keytop - Scanner NA |
| Парткод: | B238 1575 |
| Деталь: | Keytop - Scanner EU |
| Парткод: | B238 1581 |
| Деталь: | PCB OP-L |
| Парткод: | B223 1475 |
| Деталь: | Harness - OP-R 10p |
| Парткод: | B238 1480 |
| Деталь: | Harness - OP-R 13p |
| Парткод: | B238 1481 |
| Деталь: | Operation Panel Bracket |
| Парткод: | B238 1527 |
| Деталь: | INSULATOR |
| Парткод: | B238 1533 |
| Деталь: | PCB:APC1:LCDC:NA |
| Парткод: | B223 1461 |
| Деталь: | PCB:LCDC:EU |
| Парткод: | B223 1462 |
| Деталь: | Invertor - TFT |
| Парткод: | B223 1486 |
| Деталь: | Harness - Invertor |
| Парткод: | B238 1484 |
| Деталь: | Operation Panel Bracket - Right |
| Парткод: | B238 1548 |
| Деталь: | Lens - Front |
| Парткод: | B238 1519 |
| Деталь: | Shadeing Plate:Touch Panel:Assy |
| Парткод: | B223 1507 |
| Деталь: | Touch Panel - W-VGA F |
| Парткод: | B223 1494 |
| Деталь: | LCD Spacer A |
| Парткод: | B238 1534 |
| Деталь: | LCD Spacer B |
| Парткод: | B238 1535 |
| Деталь: | LCD - TFT W-VGA SH |
| Парткод: | B223 1489 |
| Деталь: | Cable - FFC TFT LCD |
| Парткод: | B223 1487 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B238 1505 |
| Деталь: | Keytop - 10key |
| Парткод: | B238 1508 |
| Деталь: | Keytop - 10key NA |
| Парткод: | B238 1584 |
| Деталь: | Keytop - Clear Modes |
| Парткод: | B238 1583 |
| Деталь: | Keytop - Start |
| Парткод: | B238 1504 |
| Деталь: | Keytop - Try Print |
| Парткод: | B238 1506 |
| Деталь: | Keytop - Interrupt |
| Парткод: | B238 1509 |
| Деталь: | Keytop - Kantan |
| Парткод: | B238 1552 |
| Деталь: | Keytop - Login |
| Парткод: | B238 1550 |
| Деталь: | Keytop - Power Source |
| Парткод: | B238 1549 |
| Деталь: | Harness - OP-L 13p |
| Парткод: | B238 1483 |
| Деталь: | Harness - OP-L 12p |
| Парткод: | B238 1482 |
| Деталь: | PCB OP-R |
| Парткод: | B238 1470 |
| Деталь: | Keytop - Blank FB |
| Парткод: | B223 1518 |
| Деталь: | Keytop - Doc NA |
| Парткод: | B238 1572 |
| Деталь: | Keytop - Doc EU |
| Парткод: | B238 1578 |
| Деталь: | Keytop - Copy NA |
| Парткод: | B238 1571 |
| Деталь: | Keytop - Copy EU |
| Парткод: | B238 1577 |
| Деталь: | Cover:Scanner:Front |
| Парткод: | B223 1595 |
| Деталь: | Cover:Scanner:Front:EU |
| Парткод: | B222 1595 |
| Деталь: | Decal - Caution Original |
| Парткод: | B237 1595 |
| Деталь: | Cover:Front Right:Upper |
| Парткод: | B223 1596 |
| Деталь: | Keytop - Printer NA |
| Парткод: | B238 1574 |
| Деталь: | Keytop - Printer EU |
| Парткод: | B238 1580 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Clamp:LWSS-1N |
| Парткод: | 11 050 598 |
| Деталь: | CLAMP |
| Парткод: | 11 050 032 |
| Деталь: | Toner Cartridge Unit |
| Парткод: | B223 3305 |
| Деталь: | Toner Cartridge Guide |
| Парткод: | B223 3328 |
| Деталь: | Rail:Left:Intermediate Transfer |
| Парткод: | B223 6145 |
| Деталь: | Rail:Right:Intermediate Transfer |
| Парткод: | B223 6146 |
| Деталь: | Sheet:Harness |
| Парткод: | B223 4342 |
| Деталь: | Slide Rail:Fusing Unit |
| Парткод: | AA07 0080 |
| Деталь: | Sponge:IH:Fan |
| Парткод: | B223 1344 |
| Деталь: | Bracket:Sensor:Front |
| Парткод: | B223 1067 |
| Деталь: | Bracket:Sensor:Rear |
| Парткод: | B223 1068 |
| Деталь: | Cover:Thermopile |
| Парткод: | B223 4331 |
| Деталь: | Thermopile |
| Парткод: | AW10 0106 |
| Деталь: | Harness:IOB:Fusing:Thermopile |
| Парткод: | B223 5312 |
| Деталь: | Holder:Thermopile |
| Парткод: | B223 4332 |
| Деталь: | Stay:Temperature Sensor:Fusing |
| Парткод: | B223 4314 |
| Деталь: | Positioning Plate:Fusing Unit |
| Парткод: | B223 4391 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Screw - M3X4 |
| Парткод: | 0353 0040N |
| Деталь: | Screw M3x12 |
| Парткод: | 0353 0120N |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | Gate Pawl:Upper |
| Парткод: | B223 4495 |
| Деталь: | Gate Pawl:Entrance |
| Парткод: | B223 4475 |
| Деталь: | Gear:21Z |
| Парткод: | B223 4472 |
| Деталь: | Tension Spring:Lever |
| Парткод: | B223 4584 |
| Деталь: | DC Solenoid:Duplex |
| Парткод: | B223 4581 |
| Деталь: | Lever:Gate Pawl:Upper |
| Парткод: | B223 4477 |
| Деталь: | Decal:Open And Close |
| Парткод: | B223 4492 |
| Деталь: | Stopper:Gate Pawl:Upper |
| Парткод: | B223 4478 |
| Деталь: | Tension Spring:Gate Pawl:1.6n |
| Парткод: | B223 4479 |
| Деталь: | Tension Spring:10n |
| Парткод: | B223 4485 |
| Деталь: | Driven Roller:Dia16 |
| Парткод: | B223 4474 |
| Деталь: | BUSHING - M4 |
| Парткод: | G060 4435 |
| Деталь: | Compression Spring:Driven Roller |
| Парткод: | B223 4484 |
| Деталь: | Guide Plate:Open And Close |
| Парткод: | B223 4471 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Bracket:Paper Exit Unit:Rear |
| Парткод: | B223 4481 |
| Деталь: | Gate Pawl:Duplex |
| Парткод: | B223 4578 |
| Деталь: | Tension Spring:Gate Pawl:0.5n |
| Парткод: | B223 4589 |
| Деталь: | Guide Plate:Left Upper |
| Парткод: | B223 4503 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Ring Separator |
| Парткод: | 8 050 097 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Clamp:LES-0505 |
| Парткод: | 11 050 551 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Stepper Motor:DC4.08V 2.4W |
| Парткод: | B802 1812 |
| Деталь: | Rubber Bushing - 6 45hs |
| Парткод: | AA10 1021 |
| Деталь: | Bracket:Reverse:Drive |
| Парткод: | B802 1815 |
| Деталь: | COLLAR |
| Парткод: | B044 1825 |
| Деталь: | Timing Belt:40S2M128 |
| Парткод: | J503 3116 |
| Деталь: | Sensor Shielding Plate |
| Парткод: | G570 1225 |
| Деталь: | Bracket:Sensor:Pickup |
| Парткод: | B802 1985 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Timing Belt:40S2M120 |
| Парткод: | AA04 3323 |
| Деталь: | Bracket:Pickup:Drive |
| Парткод: | B802 1925 |
| Деталь: | Stepper Motor:Pm:S2m:T15:Assy |
| Парткод: | B700 5805 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Cam:Stopper Pawl |
| Парткод: | B802 1951 |
| Деталь: | Gear - 25Z |
| Парткод: | B351 1791 |
| Деталь: | Gear - 18Z |
| Парткод: | B351 1781 |
| Деталь: | Timing Pulley:T33-Z17 |
| Парткод: | B802 1931 |
| Деталь: | Stopper:Cam:Pickup |
| Парткод: | B802 1942 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Feeler:Cam:Pickup |
| Парткод: | B802 1943 |
| Деталь: | Gear - 24Z |
| Парткод: | A680 2261 |
| Деталь: | Cam:Pickup |
| Парткод: | B802 1941 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Cover:Paper Feed |
| Парткод: | B802 4121 |
| Деталь: | Grip:Cover |
| Парткод: | B802 4152 |
| Деталь: | Decal:Misfeed Removal:Original |
| Парткод: | B802 6012 |
| Деталь: | Decal:Size:Original |
| Парткод: | B652 1807 |
| Деталь: | Sound Proofing Material |
| Парткод: | B802 4711 |
| Деталь: | Hook:Grip:Cover:Front |
| Парткод: | B802 4154 |
| Деталь: | Hook:Grip:Cover:Inner Back |
| Парткод: | B802 4155 |
| Деталь: | Shaft:Grip:Cover |
| Парткод: | B802 4158 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 2262 |
| Деталь: | Bracket:Cover:Front |
| Парткод: | B802 4241 |
| Деталь: | Bracket:Cover:Inner Back |
| Парткод: | B802 4231 |
| Деталь: | Stopper:Cover |
| Парткод: | B802 4162 |
| Деталь: | Shaft:Cleaner |
| Парткод: | AA14 3789 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Bracket:Paper Size Sensor |
| Парткод: | B802 4252 |
| Деталь: | Harness:Paper Feed |
| Парткод: | B802 5840 |
| Деталь: | PHOTOINTERRUPTOR:ENTRANCE |
| Парткод: | AW02 0154 |
| Деталь: | Photointerruptor:Paper Size Sensor |
| Парткод: | AW02 0155 |
| Деталь: | PHOTO REFIECTION SENSOR:EXIT |
| Парткод: | GW01 0007 |
| Деталь: | Photo Reflection Sensor |
| Парткод: | AW01 0091 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Feeler:Original Sensor |
| Парткод: | B802 4263 |
| Деталь: | Screw:Mm5:2.5MM |
| Парткод: | GA14 3003 |
| Деталь: | Tapping Screw:3x10 |
| Парткод: | 0451 3010N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Sheet:Transport Unit |
| Парткод: | B223 4555 |
| Деталь: | Bracket:Guide Plate |
| Парткод: | B223 4554 |
| Деталь: | Harness:Ground Wire |
| Парткод: | B223 4557 |
| Деталь: | Lever Shaft - Front |
| Парткод: | B223 6322 |
| Деталь: | Lever Shaft - Rear |
| Парткод: | B223 6323 |
| Деталь: | Release Lever |
| Парткод: | B223 6306 |
| Деталь: | Lever Bracket - Middle |
| Парткод: | B223 6320 |
| Деталь: | Driven Roller:Dia16 |
| Парткод: | B223 4559 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B223 4556 |
| Деталь: | Transfer/Separation Unit:AP:Assy |
| Парткод: | B223 6263 |
| Деталь: | TERMINAL |
| Парткод: | B223 6289 |
| Деталь: | Transfer Roller Terminal |
| Парткод: | B223 6285 |
| Деталь: | Sheet:Case:Lower |
| Парткод: | B223 6327 |
| Деталь: | Transfer Roller Case |
| Парткод: | B223 6281 |
| Деталь: | Tension Spring:Driven Roller |
| Парткод: | B223 4553 |
| Деталь: | Bushing:Dia4 |
| Парткод: | B223 4552 |
| Деталь: | Ground Wire - Power Pack |
| Парткод: | B223 6317 |
| Деталь: | Power Pack:D |
| Парткод: | AZ30 0058 |
| Деталь: | Harness - Second Transfer Unit |
| Парткод: | B223 4561 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2145 |
| Деталь: | Torsion Spring:Front |
| Парткод: | B223 4542 |
| Деталь: | Torsion Spring:Rear |
| Парткод: | B223 4541 |
| Деталь: | Guide Plate:Transfer Unit:Holder |
| Парткод: | B223 4551 |
| Деталь: | Drum Stay - Rear |
| Парткод: | B223 6290 |
| Деталь: | Cover - Entrance Sensor |
| Парткод: | B238 4739 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0118 |
| Деталь: | Entrance Sensor Bracket |
| Парткод: | B238 4733 |
| Деталь: | Decal:Warning (High Temperature) |
| Парткод: | B223 4394 |
| Деталь: | Sheet:Harness |
| Парткод: | B223 4558 |
| Деталь: | Spring Cap |
| Парткод: | B223 6319 |
| Деталь: | Transfer Spring |
| Парткод: | B223 6308 |
| Деталь: | Spring Anchor |
| Парткод: | B223 6321 |
| Деталь: | Guide Pin:Holder |
| Парткод: | B223 4545 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Bracket:Sheet Through |
| Парткод: | B180 1731 |
| Деталь: | Spacer:Bracket:Scale:Left |
| Парткод: | B223 1785 |
| Деталь: | Scale:Machine Or Copier |
| Парткод: | B223 1773 |
| Деталь: | Exposure Glass:Sheet Through:344x20 |
| Парткод: | BC01 2002 |
| Деталь: | Seal:Sheet Through |
| Парткод: | B223 1774 |
| Деталь: | Scale:Left:Na |
| Парткод: | B223 1787 |
| Деталь: | Scale:Left |
| Парткод: | B223 1777 |
| Деталь: | Exposure Glass |
| Парткод: | A250 1752 |
| Деталь: | Frame:Scanner:Front |
| Парткод: | B051 1727 |
| Деталь: | Frame:Scanner:Rear |
| Парткод: | B223 1788 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 54 421 924 |
| Деталь: | Scale:Rear:Printing |
| Парткод: | B132 1692 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Scanner Home Sensor Stopper |
| Парткод: | A193 1793 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Harness:Sio:Sensor |
| Парткод: | B223 5202 |
| Деталь: | Photointerruptor:Flat:PICH2mm:M4 |
| Парткод: | AW02 0146 |
| Деталь: | Document Feeder:Connector:Bracket |
| Парткод: | B223 1808 |
| Деталь: | Harness:Sio:Ardf |
| Парткод: | B223 5203 |
| Деталь: | Cam:Guide Plate:Scanner:Left |
| Парткод: | B223 1116 |
| Деталь: | Decal:Size:Original |
| Парткод: | B652 1807 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw:3x10 |
| Парткод: | 0451 3010N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0453 3006N |
| Деталь: | Screw - M4X12 |
| Парткод: | 0314 0120N |
| Деталь: | Binding Self Tapping Screw:3x8 |
| Парткод: | 0453 3008N |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11 050 522 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Edge Saddle:Les-2017 |
| Парткод: | 11 050 544 |
| Деталь: | Fan Motor - DC24V |
| Парткод: | GX64 0020 |
| Деталь: | Duct:Fusing |
| Парткод: | B223 1326 |
| Деталь: | Duct:Fusing:Rear |
| Парткод: | B223 1327 |
| Деталь: | Harness:IOB:Connecting:IH |
| Парткод: | B223 5305 |
| Деталь: | Invertor:IH |
| Парткод: | B223 5170 |
| Деталь: | Invertor:IH:EU |
| Парткод: | B223 5172 |
| Деталь: | Guide:Gear |
| Парткод: | B223 2694 |
| Деталь: | Timing Belt:40S2M144 |
| Парткод: | B700 2649 |
| Деталь: | Gear Pulley |
| Парткод: | AB01 7493 |
| Деталь: | COLLAR |
| Парткод: | B044 1825 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B223 2691 |
| Деталь: | Rubber Bushing - 6 45hs |
| Парткод: | AA10 1021 |
| Деталь: | Stepper Motor:DC24V 26.4W |
| Парткод: | B223 2685 |
| Деталь: | SHAFT |
| Парткод: | B238 1225 |
| Деталь: | CAM |
| Парткод: | B238 1226 |
| Деталь: | HOLDER |
| Парткод: | B238 1223 |
| Деталь: | DC Motor 24V |
| Парткод: | B223 1199 |
| Деталь: | Fan Motor - Mm60 DC24V |
| Парткод: | B223 1332 |
| Деталь: | Bracket:Fan:Power Source:IH |
| Парткод: | B223 5844 |
| Деталь: | Hinge:Application:Rack |
| Парткод: | B223 5841 |
| Деталь: | Bracket:Rack:Application |
| Парткод: | B223 5843 |
| Деталь: | Ground Wire:Rack:Right Lower:HF |
| Парткод: | B223 5866 |
| Деталь: | Harness:IOB:Counter:Option:NA |
| Парткод: | B223 5335 |
| Деталь: | Bracket:Total Counter |
| Парткод: | B223 5846 |
| Деталь: | Total Counter:7FIG:24V |
| Парткод: | AX31 0045 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Screw:M3x8 |
| Парткод: | 0353 0080N |
| Деталь: | Tapping Screw:3x30 |
| Парткод: | 0451 3030N |
| Деталь: | Tapping Screw - M3x30 |
| Парткод: | 8 025 304 |
| Деталь: | CLAMP |
| Парткод: | 11 050 641 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Bracket:Connector:Heater |
| Парткод: | B223 1206 |
| Деталь: | Guide:Connector:Heater:Imaging Unit |
| Парткод: | B238 1143 |
| Деталь: | Cover - Positioning Pin |
| Парткод: | B238 1089 |
| Деталь: | Set Sensor Bracket |
| Парткод: | B223 6507 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Tray Cover - Right |
| Парткод: | B238 2541 |
| Деталь: | Tray Cover - Middle |
| Парткод: | B238 2544 |
| Деталь: | Harness - Paper Volume Sensor |
| Парткод: | B238 5325 |
| Деталь: | DC Motor 24V |
| Парткод: | AX04 0154 |
| Деталь: | Paper Tray Stopper Assy |
| Парткод: | B223 2730 |
| Деталь: | Rear Pipe Assy |
| Парткод: | B223 6481 |
| Деталь: | Drive Unit:Collection Bottle |
| Парткод: | B223 1174 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0722 |
| Деталь: | Pulley:Idler:Fusing |
| Парткод: | AB03 0551 |
| Деталь: | Pulley - 34T |
| Парткод: | AB03 0783 |
| Деталь: | Timing Belt - S2M460 |
| Парткод: | AA04 3583 |
| Деталь: | COVER |
| Парткод: | B223 2722 |
| Деталь: | Bracket:Push Switch |
| Парткод: | B223 2721 |
| Деталь: | Push Switch:Paper Size Sensor |
| Парткод: | AW50 0038 |
| Деталь: | Cover - Tray Left |
| Парткод: | B238 2543 |
| Деталь: | Bracket:Base:Connector |
| Парткод: | B223 5848 |
| Деталь: | Main Switch Sheet |
| Парткод: | B238 5828 |
| Деталь: | Main Switch Bracket |
| Парткод: | B238 5827 |
| Деталь: | Harness:AC:Switch |
| Парткод: | B223 5330 |
| Деталь: | Cover - Connector |
| Парткод: | B238 1088 |
| Деталь: | Connector bracket |
| Парткод: | B223 1065 |
| Деталь: | Cover:Connector:Heater |
| Парткод: | B223 5849 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Hexagonal Head Bolt W/Washer:M3x6 |
| Парткод: | 8 010 231 |
| Деталь: | Tapping Screw:3x8 |
| Парткод: | 0454 3008Q |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 8 025 299 |
| Деталь: | Switch - RS1A-AB11 |
| Парткод: | 12 042 704 |
| Деталь: | Connector - QR/P17-14S-B |
| Парткод: | 11 028 534 |
| Деталь: | Carriage:No.2 |
| Парткод: | B223 1721 |
| Деталь: | Spring Plate - 2nd Mirror |
| Парткод: | G404 2810 |
| Деталь: | Mirror:No.2:Concave |
| Парткод: | B223 1754 |
| Деталь: | Mirror:No.2:Convax |
| Парткод: | B223 1755 |
| Деталь: | Pulley Holder |
| Парткод: | G570 2833 |
| Деталь: | Guide - High Voltage Supply Cord |
| Парткод: | G570 2832 |
| Деталь: | Pulley - High Voltage Supply Cord |
| Парткод: | G570 2834 |
| Деталь: | Stabilizer:T |
| Парткод: | AZ50 0070 |
| Деталь: | Harness:Sio:Lamp Regulator |
| Парткод: | B223 5204 |
| Деталь: | Harness:Sio:Machine Or Copier |
| Парткод: | B223 5223 |
| Деталь: | Harness:Sio:Scanner Unit |
| Парткод: | B223 5226 |
| Деталь: | PCB:SIO |
| Парткод: | B223 5106 |
| Деталь: | Cover:Stepper Motor:Rear |
| Парткод: | B223 1779 |
| Деталь: | Bracket:Exterior:Rear |
| Парткод: | B223 1807 |
| Деталь: | Timing Belt - 157ST1.5-4.0 |
| Парткод: | B238 1792 |
| Деталь: | Stepper Motor:Assy |
| Парткод: | B180 1713 |
| Деталь: | Harness:SIO:Scanner Motor SMD |
| Парткод: | B223 5216 |
| Деталь: | Idler pulley |
| Парткод: | B238 1806 |
| Деталь: | Drive Were |
| Парткод: | B223 1782 |
| Деталь: | Bracket:Tension |
| Парткод: | B180 1704 |
| Деталь: | Tension Spring:Tension:11300mn |
| Парткод: | AA06 0980 |
| Деталь: | Spacer Bushing |
| Парткод: | G570 1160 |
| Деталь: | Pulley:Drive Were:Front:Sub-assy |
| Парткод: | B180 1810 |
| Деталь: | Pulley:Drive Were:Rear:Sub-assy |
| Парткод: | B180 1812 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2144 |
| Деталь: | Shaft:Scanner:Drive |
| Парткод: | B180 1814 |
| Деталь: | Timing Pulley 73 |
| Парткод: | G570 1133 |
| Деталь: | 1st Slide Rail |
| Парткод: | A193 1816 |
| Деталь: | Slide Rail:No.2 |
| Парткод: | B180 1734 |
| Деталь: | Tension Spring:Tension:14720mn |
| Парткод: | AA06 0979 |
| Деталь: | PULLEY |
| Парткод: | B238 1807 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 8 046 123 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 8 025 299 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Edge Saddle - Les-1010 |
| Парткод: | 11 050 518 |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 488 |
| Деталь: | Harness Clamp - LWS-2111Z |
| Парткод: | 11 050 517 |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8 050 088 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Drawer:Intermediate Transfer:Assy |
| Парткод: | B223 6140 |
| Деталь: | Harness:IOB:Toner Supply:CL |
| Парткод: | B223 5304 |
| Деталь: | Harness:P.p:High Voltage Line:T/TS |
| Парткод: | B223 5310 |
| Деталь: | Toner End Sensor |
| Парткод: | AW02 0185 |
| Деталь: | Pump Unit - BK |
| Парткод: | B223 3211 |
| Деталь: | Pump Unit - M |
| Парткод: | B223 3204 |
| Деталь: | Pump Unit - C |
| Парткод: | B223 3203 |
| Деталь: | Pump Unit - Y |
| Парткод: | B223 3202 |
| Деталь: | TUBE CLAMP |
| Парткод: | B223 3206 |
| Деталь: | Nozzle Assy |
| Парткод: | B223 3205 |
| Деталь: | Tube Clip |
| Парткод: | B223 3209 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Connector - 2P |
| Парткод: | 11 026 259 |
| Деталь: | Relay Connector - 2P |
| Парткод: | 11 026 245 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Harness:Fusing Unit (120V) |
| Парткод: | B223 5361 |
| Деталь: | Harness:Fusing Unit (230V) |
| Парткод: | B223 5362 |
| Деталь: | Screw:M3 |
| Парткод: | AA14 3576 |
| Деталь: | Bracket:Drawer |
| Парткод: | B223 1069 |
| Деталь: | Duct:Supply:Rear |
| Парткод: | B223 1342 |
| Деталь: | Duct:Supply:Front |
| Парткод: | B223 1341 |
| Деталь: | Fan Motor - Mm60 DC24V |
| Парткод: | B223 1332 |
| Деталь: | Duct:IH:Rear |
| Парткод: | B223 1324 |
| Деталь: | Duct:IH:Front |
| Парткод: | B223 1323 |
| Деталь: | Brushless Motor:Drive:Paper Feed |
| Парткод: | GX06 0015 |
| Деталь: | Bracket:Fusing Drive Sub-unit:Assy |
| Парткод: | B223 1195 |
| Деталь: | Gear:Z27/Z78 |
| Парткод: | AB01 0377 |
| Деталь: | Gearz120 |
| Парткод: | AB01 0375 |
| Деталь: | Gear:Z27 |
| Парткод: | AB01 0376 |
| Деталь: | Cover:Fusing Drive Unit:Lower |
| Парткод: | B223 1362 |
| Деталь: | Ring:Gear:Heat Roller |
| Парткод: | B223 4343 |
| Деталь: | Gear:Z24 |
| Парткод: | AB01 1264 |
| Деталь: | SPRING |
| Парткод: | AA06 6178 |
| Деталь: | Bracket:Drive:Gear |
| Парткод: | B223 4315 |
| Деталь: | Gear:Z16/Z40 |
| Парткод: | AB01 7706 |
| Деталь: | Gear:Z28 |
| Парткод: | AB01 0138 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B223 4318 |
| Деталь: | Stepper Motor:DC24V 24.3W |
| Парткод: | B223 4317 |
| Деталь: | Power Pack:TTS:APO-C/P |
| Парткод: | AZ32 0154 |
| Деталь: | Harness:AC:Scanner:Heater |
| Парткод: | B223 5342 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Screw - M4X8 |
| Парткод: | 0954 4008N |
| Деталь: | Harness Clamp |
| Парткод: | 11 050 487 |
| Деталь: | CLAMP |
| Парткод: | 11 050 516 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Connector:51405-1819 |
| Парткод: | 11 029 782 |
| Деталь: | Paper Tray Unit No.1 |
| Парткод: | B223 2850 |
| Деталь: | Screw:DIA6 |
| Парткод: | AA14 3843 |
| Деталь: | Slide Rail - Left |
| Парткод: | B223 2890 |
| Деталь: | Slide Rail Stopper - Left |
| Парткод: | B223 2894 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B223 2940 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3006 |
| Деталь: | Decal - Paper Set Direction No.1 |
| Парткод: | B237 2521 |
| Деталь: | Cover - Paper Tray No.1 |
| Парткод: | B223 2857 |
| Деталь: | Paper Tray Grip |
| Парткод: | B223 2860 |
| Деталь: | Decal - Grip |
| Парткод: | B238 2526 |
| Деталь: | Lever - Release Inner |
| Парткод: | B223 2862 |
| Деталь: | Tension Spring:Grip |
| Парткод: | AA06 1014 |
| Деталь: | Release Shaft |
| Парткод: | B223 2863 |
| Деталь: | Grip Holder |
| Парткод: | B223 2861 |
| Деталь: | External Circlip - Mm8 |
| Парткод: | A222 2724 |
| Деталь: | Lever - Release Outer |
| Парткод: | B223 2864 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | END FENCE |
| Парткод: | B223 2912 |
| Деталь: | Side Fence - Front |
| Парткод: | B223 2870 |
| Деталь: | Stopper Lever - Front |
| Парткод: | B223 2923 |
| Деталь: | Spring Plate - Release Lever |
| Парткод: | B004 2923 |
| Деталь: | Plate - Side Fence Right |
| Парткод: | B223 2935 |
| Деталь: | Plate - Side Fence |
| Парткод: | B223 2934 |
| Деталь: | Gear - 16Z |
| Парткод: | B223 2936 |
| Деталь: | Rise No.1 Shaft |
| Парткод: | B223 2865 |
| Деталь: | Rise Lever |
| Парткод: | B223 2918 |
| Деталь: | Side Fence - Rear |
| Парткод: | B223 2880 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A267 2860 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Decal - Side Fence Rear |
| Парткод: | B223 2873 |
| Деталь: | Tension Spring:Side Fence:Rear |
| Парткод: | AA06 1003 |
| Деталь: | GROUND PLATE |
| Парткод: | B223 2869 |
| Деталь: | Screw:Tp:M4 |
| Парткод: | AA14 3577 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0450 4008N |
| Деталь: | Binding Self Tapping Screw:3x8 |
| Парткод: | 0453 3008N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | MANUAL FEED TABLE |
| Парткод: | B223 2662 |
| Деталь: | Side Fence:Front |
| Парткод: | B223 2688 |
| Деталь: | Side Fence:Rear |
| Парткод: | B223 2671 |
| Деталь: | Grip:Side Fence |
| Парткод: | B223 2667 |
| Деталь: | Spring Plate:Stopper |
| Парткод: | B223 2668 |
| Деталь: | Decal:Side Fence |
| Парткод: | B223 2645 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | B223 2655 |
| Деталь: | Cover:Manual Feed |
| Парткод: | B223 2661 |
| Деталь: | Decal:Scale |
| Парткод: | B223 2644 |
| Деталь: | Harness:Paper Size Sensor |
| Парткод: | B223 2669 |
| Деталь: | Paper size sensor |
| Парткод: | AW50 0031 |
| Деталь: | Rack:Manual Feed |
| Парткод: | B223 2631 |
| Деталь: | Gear:16z |
| Парткод: | B223 2666 |
| Деталь: | EXTENSION TRAY |
| Парткод: | B223 2663 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
| Деталь: | Positioning Plate:Front |
| Парткод: | B802 1121 |
| Деталь: | Positioning Plate:Rear |
| Парткод: | B802 1131 |
| Деталь: | Cover:Paper Feed Sensor |
| Парткод: | B802 1141 |
| Деталь: | Cushion:Left |
| Парткод: | B802 4631 |
| Деталь: | Cushion:Left |
| Парткод: | B802 4713 |
| Деталь: | Cushion:Inner Back |
| Парткод: | B802 4714 |
| Деталь: | Screw:Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Hinge:Left |
| Парткод: | B802 1311 |
| Деталь: | Hinge:Right |
| Парткод: | B802 1351 |
| Деталь: | Filter - DF Open Sensor |
| Парткод: | A859 1841 |
| Деталь: | Pressure plate |
| Парткод: | B802 4611 |
| Деталь: | Drum Stay:Pressure Plate |
| Парткод: | B802 4621 |
| Деталь: | Pressure Plate Tape |
| Парткод: | B477 2715 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Gear:Z17 |
| Парткод: | B802 1671 |
| Деталь: | Gear:Z21/Z23 |
| Парткод: | B802 1661 |
| Деталь: | Gear:Z37 |
| Парткод: | B802 1642 |
| Деталь: | Gear:Z26 |
| Парткод: | B802 1643 |
| Деталь: | Gear:Z25 |
| Парткод: | B802 1651 |
| Деталь: | Timing Pulley:T31 |
| Парткод: | B802 1631 |
| Деталь: | Gear:Z18 |
| Парткод: | B802 1632 |
| Деталь: | Gear:Z19 |
| Парткод: | B802 1633 |
| Деталь: | Timing Belt:40S1.5M150 |
| Парткод: | AA04 3320 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B802 1715 |
| Деталь: | Stay:Motor:Scanning |
| Парткод: | B802 1731 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0842 |
| Деталь: | Bracket:Protect:Drive |
| Парткод: | B802 1736 |
| Деталь: | Stepper Motor:DC1.76V 3.7W |
| Парткод: | B802 1721 |
| Деталь: | Gear:Z18 |
| Парткод: | B802 1681 |
| Деталь: | Timing Pulley:T31/T61 |
| Парткод: | B802 1741 |
| Деталь: | Timing Belt:40S1.5M157.5 |
| Парткод: | AA04 3322 |
| Деталь: | Timing Pulley:T31 |
| Парткод: | B802 1762 |
| Деталь: | SCREW |
| Парткод: | B238 4483 |
| Деталь: | Bracket:Tension |
| Парткод: | B802 1755 |
| Деталь: | Gear:Z18 |
| Парткод: | B802 1641 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Binding Self Tapping Screw:4x6 |
| Парткод: | 0453 4006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Ball Bearing - 6x12x4 Mm |
| Парткод: | 7 413 506 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 11 050 511 |
| Деталь: | Cover:Left:Middle |
| Парткод: | B223 1283 |
| Деталь: | Filter:Image Forming MD |
| Парткод: | B223 1348 |
| Деталь: | Cover:Left |
| Парткод: | B223 1281 |
| Деталь: | Cover - Main Switch |
| Парткод: | B223 1255 |
| Деталь: | Decal - Main Switch(on-off) |
| Парткод: | B238 1372 |
| Деталь: | Collection Bottlecover - Front |
| Парткод: | B223 1254 |
| Деталь: | Decal - Power Source:Off |
| Парткод: | B132 1573 |
| Деталь: | MAGNET CATCH |
| Парткод: | AA02 1030 |
| Деталь: | Ozone Filter:No.1 |
| Парткод: | B223 1277 |
| Деталь: | Inner Cover - Left |
| Парткод: | B223 1242 |
| Деталь: | Emblem Cover |
| Парткод: | B223 1253 |
| Деталь: | Sheet:Emblem:AP-C1c:RIC |
| Парткод: | B222 8331 |
| Деталь: | Sheet:Emblem:AP-C1c:SVN |
| Парткод: | B222 8332 |
| Деталь: | Sheet:Emblem:AP-C1c:GES:NA |
| Парткод: | B222 8333 |
| Деталь: | Sheet:Emblem:AP-C1c:LAN:NA |
| Парткод: | B222 8334 |
| Деталь: | Sheet:Emblem:AP-C1c:INF |
| Парткод: | B222 8335 |
| Деталь: | Sheet:Emblem:AP-C1c:NSA |
| Парткод: | B222 8336 |
| Деталь: | Sheet:Emblem:AP-C1c:REX |
| Парткод: | B222 8337 |
| Деталь: | Sheet:Emblem:AP-C1c:GES:EU |
| Парткод: | B222 8338 |
| Деталь: | Sheet:Emblem:AP-C1c:LAN:EU |
| Парткод: | B222 8339 |
| Деталь: | Sheet:Emblem:AP-C1c:GES:AA |
| Парткод: | B222 8343 |
| Деталь: | Sheet:Emblem:AP-C1d:RIC |
| Парткод: | B224 8331 |
| Деталь: | Sheet:Emblem:AP-C1d:SVN |
| Парткод: | B224 8332 |
| Деталь: | Sheet:Emblem:AP-C1d:GES:NA |
| Парткод: | B224 8333 |
| Деталь: | Sheet:Emblem:AP-C1d:LAN:NA |
| Парткод: | B224 8334 |
| Деталь: | Sheet:Emblem:AP-C1d:INF |
| Парткод: | B224 8335 |
| Деталь: | Sheet:Emblem:AP-C1d:NSA |
| Парткод: | B224 8336 |
| Деталь: | Sheet:Emblem:AP-C1d:REX |
| Парткод: | B224 8337 |
| Деталь: | Sheet:Emblem:AP-C1d:GES:EU |
| Парткод: | B224 8338 |
| Деталь: | Sheet:Emblem:AP-C1d:LAN:EU |
| Парткод: | B224 8339 |
| Деталь: | Sheet:Emblem:AP-C1d:GES:AA |
| Парткод: | B224 8343 |
| Деталь: | Hinge - Front Cover |
| Парткод: | G020 1332 |
| Деталь: | TAPPING SCREW |
| Парткод: | AA14 3823 |
| Деталь: | Cover:Front:EU |
| Парткод: | B224 1251 |
| Деталь: | Guide Plate:Scanner |
| Парткод: | B223 1246 |
| Деталь: | MAGNET CATCH |
| Парткод: | B024 1264 |
| Деталь: | Sheet:Misfeed Removal |
| Парткод: | B223 1256 |
| Деталь: | Cleaner:Shield Glass:Assy |
| Парткод: | B223 1279 |
| Деталь: | Cover - Right |
| Парткод: | B238 1380 |
| Деталь: | Cover:Right:Rear |
| Парткод: | B223 1272 |
| Деталь: | Filter:Right Rear |
| Парткод: | B223 1276 |
| Деталь: | Cover:Right Rear:Fan |
| Парткод: | B223 1274 |
| Деталь: | Cap:Cover:Rear |
| Парткод: | B223 1293 |
| Деталь: | Cover:Rear:Upper |
| Парткод: | B223 1292 |
| Деталь: | Cover:Rear |
| Парткод: | B223 1291 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Guide:Scanning:Entrance:Lower |
| Парткод: | B802 3412 |
| Деталь: | Sheet:Roller:Scanning:Entrance |
| Парткод: | B802 3413 |
| Деталь: | Sheet:Scanning:Entrance |
| Парткод: | B802 3414 |
| Деталь: | Roller:Scanning:Driven |
| Парткод: | B802 3471 |
| Деталь: | Shaft:Driven:Exit |
| Парткод: | B802 3592 |
| Деталь: | Plate:Entrance:Pressure:Auxiliary |
| Парткод: | B802 3426 |
| Деталь: | Spring Plate:Scanning:Enrrrance:Driven |
| Парткод: | B802 3427 |
| Деталь: | Stay:Scanning:Entrance:Lower |
| Парткод: | B802 3422 |
| Деталь: | Guide Plate:Scanning |
| Парткод: | B802 3511 |
| Деталь: | SCREW |
| Парткод: | AA14 3569 |
| Деталь: | Guide:Scanning:Exit:Lower |
| Парткод: | B802 3553 |
| Деталь: | Plate:Exit:Pressure:Auxiliary |
| Парткод: | B802 3566 |
| Деталь: | Spring Plate:Scanning:Exit:Driven:Upper |
| Парткод: | B802 3567 |
| Деталь: | Spring Plate:Scanning:Exit:Driven:Lower |
| Парткод: | B802 3568 |
| Деталь: | Stay:Scanning:Exit:Lower |
| Парткод: | B802 3561 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | Stopper:Guide:Reverse |
| Парткод: | B802 2291 |
| Деталь: | PHOTO REFIECTION SENSOR:EXIT |
| Парткод: | GW01 0007 |
| Деталь: | Bracket:Sensor:Scanning:Exit |
| Парткод: | B802 3851 |
| Деталь: | Discharge Brush:Reverse |
| Парткод: | B802 3755 |
| Деталь: | Spring Plate |
| Парткод: | B802 3711 |
| Деталь: | Exit Driven Roller |
| Парткод: | B789 3712 |
| Деталь: | Scanning Driven Shaft |
| Парткод: | B789 3491 |
| Деталь: | DC Solenoid:Transmited Rubber Stamp |
| Парткод: | B714 5006 |
| Деталь: | STAMP |
| Парткод: | H511 5007 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0453 3006N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | B223 6464 |
| Деталь: | Transport Screw Bracket |
| Парткод: | B223 6471 |
| Деталь: | Bushing - 5x 10x2.5 |
| Парткод: | B223 6475 |
| Деталь: | Gear - 21Z |
| Парткод: | B223 6472 |
| Деталь: | Bushing - Dia5 |
| Парткод: | B223 6476 |
| Деталь: | Transport Screw Shaft |
| Парткод: | B223 6473 |
| Деталь: | GEAR - 29Z |
| Парткод: | B223 6474 |
| Деталь: | Gear - 20Z |
| Парткод: | B223 6463 |
| Деталь: | Pipe:Front:Assy |
| Парткод: | B223 6451 |
| Деталь: | Separation Plate - Upper Left |
| Парткод: | B223 1087 |
| Деталь: | Separation Plate - Upper Middle Left |
| Парткод: | B223 1084 |
| Деталь: | Separation Plate - Upper Middle Right |
| Парткод: | B223 1080 |
| Деталь: | Separation Plate - Upper Right |
| Парткод: | B223 1076 |
| Деталь: | Lever Bracket |
| Парткод: | B223 6467 |
| Деталь: | Bracket:Hinge:Left |
| Парткод: | B223 1103 |
| Деталь: | Bracket:Grip:Right Front |
| Парткод: | B223 1102 |
| Деталь: | Imaging Unit Plate - Outer |
| Парткод: | B223 1899 |
| Деталь: | Imaging Unit Plate - Inner |
| Парткод: | B223 1898 |
| Деталь: | Imaging Unit Plate - Front |
| Парткод: | B223 1896 |
| Деталь: | Imaging Unit Plate - Rear |
| Парткод: | B223 1897 |
| Деталь: | Cap:Grip |
| Парткод: | B223 1245 |
| Деталь: | Grip:Front |
| Парткод: | B223 1101 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - 3x16 |
| Парткод: | 0451 3016N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 8 025 305 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 8 050 089 |
Коды ошибок
101
120
121
141
142
144-001
144-002
144-003
161
165
195
202
203
204
210
211
212
213
220
221
222
223
224
225
226
227
230
231
232
233
234
235
236
237
240
241
242
243
285
290
291
292
293
294
295
296
300
301
302
303
360
361
362
363
364
365
366
367
372
373
374
375
380
396
397
398
399
400
441
442
443
452
460
490
491
492
498
501
502
503-02
504-01
504-02
529
530
531
532
533
534
535
540
541
542
543
544
547
548
549
551
552
553
554
557
559
561
562
563
564
565
580
581
582
583
584
585
586
587
610
611
620
621
622
630
632
633
634
635
650
651
669
670
672
681
682
683
687
689
690
700
701
725
730
740
741
742
743
744
746
750
760
761
763
764
791
792
818
819
820
821
822
823
824
826
827
828
829
851
853
854
855, 856
857
860
861
863
864
865
866
867
868
870
872
873
874
875
876
877
880
900
910...914
919
920
921
925
990
991
992
994
995
997
998
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 141 |
| Display: | SVC 141 ERROR |
| Description: | Motor |
| Causes: | • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor excessive PWM - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board” |
| Error code: | 142 |
| Display: | Contact the Service center. 142: Error |
| Description: | Motor |
| Causes: | • Standard white plate defective, dirty • Moisture inside the scanner unit • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor, over speed - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”. |
| Error code: | 144-001 |
| Description: | SBU connection error The SBU connection cannot be detected at power on or recovery from the energy save mode. |
| Causes: | • Insufficient power supply for SBU • Defective SBU • Defective harness • Defective detection port on the BCU |
| Remedy: | 1. Replace the harness. 2. Replace the SBU. 3. Replace the BCU. |
| Error code: | 144-002 |
| Description: | SBU serial communication error The power ON of the SBU is not detected. |
| Causes: | • Defective SIO • Defective harness • Defective detection port on the BCU |
| Remedy: | 1. Replace the harness. 2. Replace the SIO. 3. Replace the BCU. |
| Error code: | 144-003 |
| Description: | GASBU reset error The serial communication does not work. |
| Causes: | • Defective SBU • Defective detection circuit on the BCU • Defective harness |
| Remedy: | 1. Replace the SBU. 2. Replace the BCU. 3. Replace the harness. |
| Error code: | 161 |
| Display: | SYSTEM HALT (*) 161 : PCB MAIN-F6 |
| Description: | IPU Error At power on, or when the machine returns from an energy save mode, the self-diagnostic program returned an IPU error. |
| Causes: | • IPU defective • Connection between SBU and IPU is loose, broken, or defective |
| Error code: | 165 |
| Description: | Out of Paper; Load Tray 1 (MPT) with [size] [type] The Tray 1 (MPT) No Paper Sensor indicates Tray 1 (MPT) is empty. |
| Causes: | • No Paper Sensor, PL5.3.14 • No Paper Sensor Actuator, PL5.3.15 • FRONT/DUP Harness, PL5.3.28 |
| Remedy: | 1 Fill Tray 1 (MPT) with paper. Does the error persist? Go to Step 2. Complete. 2 Check the following for evidence of fault or damage: • Tray 1 (MPT) No Paper Sensor, PL5.3.14 • Sensor Actuator, PL5.3.15 Is there any damage? Replace any damaged parts. Go to Step 3. 3 Test the Tray 1 (MPT) No Paper Sensor. Run the Service Diagnostics Tray 1 (MPT) No Paper Sensor test. Does the sensor function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the Tray 1 (MPT) No Paper Sensor signal. Is there +3.3 V across P/J135-1 <=> P/J135-2? Replace the sensor. Go to Step 5. 5 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J13 and P/J135. 2. Check continuity between J13 <=> J134. Replace the Engine Control Board. Replace the FRONT/DUP Harness. |
| Error code: | 195 |
| Description: | Serial Number Error |
| Causes: | The serial number stored in the memory (EGB) is not correct. |
| Remedy: | EEPROM defective EGB replaced without original EEPROM |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 204 |
| Display: | Power OFF/ON 204:Error |
| Description: | Polygon motor error 3: XSCRDY signal error |
| Causes: | The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing. |
| Remedy: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board). |
| Error code: | 210 |
| Description: | EM Null page cargo |
| Causes: | • Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB |
| Remedy: | 1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 211 |
| Display: | ERROR 211 HeadWARM.THERM(----) |
| Description: | EM Null page |
| Causes: | • Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB |
| Remedy: | 1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 212 |
| Description: | Install or Reseat Imaging Unit The Imaging Unit CRUM fails to detect the Imaging Unit. |
| Causes: | • Imaging Unit, PL6.1.1 • CRUM Connector, PL7.1.4 • PHD2 Harness, PL7.1.7 • FAN/PHD/MOT Harness, PL10.1.9 |
| Remedy: | 1 Remove the Imaging Unit. Inspect the printer cavity for damage, debris, and toner under the auger area preventing the Imaging Unit from being seated properly. Is there foreign material or damage? Remove foreign material. Vacuum out loose toner if found. Go to Step 2. 2 Inspect and reseat the Imaging Unit. Does the error persist?. Go to Step 3. Complete 3 Check Imaging Unit CRUM connection. Are P/J710 and P/J484 connected? Go to Step 4. Reconnect the CRUM. 4 Check all pins on the PHD2 Harness PL7.1.7 for continuity. 1. Disconnect P/J710 and P/J484. 2. Check continuity between J484<=>J710. Go to Step 5 Replace PHD2 Harness. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J484 and P/J48. 2. Check continuity between J48 <=> P484. Go to Step 6 Replace the FAN/PHD/MOT Harness 6 Replace the Imaging Unit. Does the error persist? Replace the Engine Control Board. Complete |
| Error code: | 213 |
| Display: | Power OFF/ON 213:Error |
| Description: | Install or Reseat Transfer Roller The printer does not detect the presence of the Transfer Roller. |
| Causes: | • CTD (ADC) Sensor, PL5.2.19 • Transfer Roller, PL5.1.4 • FSR/ADC Harness, PL5.2.28 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Transfer Roller PL5.1.4 • CTD (ADC) Sensor PL5.2.19 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Clean the CTD (ADC) Sensor. Does this fix the problem? Complete Go to Step 3. 3 Test the CTD (ADC) Sensor. Run the Service Diagnostics CTD (ADC) Sensor test. Does the sensor function correctly? Go to Step 4. Go to Step 5. 4 Replace the Transfer Roller. Does the error persist? Go to Step 5. Complete 5 Check the CTD (ADC) Sensor connection. Is P/J136 connected to the harness? Go to Step 6. Connect the sensor. 6 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J136. 2. Check continuity between J36 <=> J136. Go to Step 7. Replace the FSR/ ADC Harness. 7 Check the CTD (ADC) Sensor signal. Disconnect P/J36. Does J36-2 <=> J36-5 = 0 V? Replace the CTD (ADC) Sensor. Replace the Engine Control Board. |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 221 |
| Description: | Laser synchronizing detection error: start position [K]: LD1 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 222 |
| Description: | Laser Synchronizing Detection Error: [M]/[C] |
| Causes: | The laser synchronizing detection signal for LDB [M]/[C] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Remedy: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB 1. Check the connectors. 2. Replace the laser optics unit. 3. Replace the EGB.· |
| Error code: | 223 |
| Description: | Metered Toner Is not Enabled A metered toner cartridge is installed while metered toner is not enabled. |
| Causes: | • Toner Cartridge (Y) PL7.2.8 • Toner Cartridge (M) PL7.2.9 • Toner Cartridge (C) PL7.2.10 • Toner Cartridge (K) PL7.2.11 |
| Remedy: | 1 Check the configuration of the Printer. Is the printer covered under a Metered Toner contract? Enable the Metered Toner via the front Panel. Replace the affected Toner Cartridge with a Non-Metered Toner Cartridge. |
| Error code: | 224 |
| Description: | Laser synchronizing detection error: start position [M]: LD0 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 225 |
| Description: | +24V Not Available to the Duplex Unit Abnormal current indicates that +24 V is not being supplied to the Duplex Unit. Applicable Status Code: Code 225: Duplex Unit is not receiving +24 V. |
| Causes: | • Motor Driver Board, PL2.1.10 • LVPS, PL3.1.1 • Duplex Unit, PL16.1.1A |
| Remedy: | 1 Check the Duplex Unit connector for damage. Is the connector damaged? Replace the connector. Go to Step 2. 2 Check for +24 V at DUPLEX on the Motor Driver Board. 1. Close the Interlock Switches. 2. Disconnect DUPLEX. Is there +24 V at DUPLEX-6 and -13 <=> ground? Replace the Duplex Control Board. Go to Step 3. 3 Check all pins on the DUPLEX Harness for continuity. Disconnect the DUPLEX Harness. Is the DUPLEX Harness conductive? Go to Step 4. Replace the DUPLEX Harness. 4 Check for +24 V from the LVPS. Disconnect POW24 on the Motor Driver Board. Is there +24 V at POW24-1 <=> ground? Replace the Motor Driver Board Go to Step 5. 5 Check the LVPS +24 V output. 1. Close the Interlock Switches. 2. Disconnect CN2. Is there +24 V at CN2-1 and <=> ground? Go to Step 6. Replace the LVPS. 6 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 226 |
| Description: | Laser synchronizing detection error: start position [C]: LD0 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 227 |
| Description: | Finisher Inverter Firmware Error Applicable Status Code: Code 227: A software error with the Inverter’s Flash Memory. |
| Causes: | • Inverter Control Board |
| Remedy: | 1 Check the following for evidence of fault or damage: • Inverter Interface Cable • Inverter connections Is there any damage? Replace any damaged parts. Go to Step 2. 2 Check the Inverter connection. Is the Inverter interface cable securely connected at both ends? Go to Step 3. Connect the Inverter to the Finisher. 3 Check the version of Inverter firmware. Is the latest version installed? Replace the Inverter Control Board. Reload the Inverter firmware. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 231 |
| Display: | Service Call 231: Error |
| Description: | FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 232 |
| Display: | Service call 232: Error |
| Description: | FGATE ON error: Y The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [Y]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 233 |
| Description: | FGATE OFF error: Y • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [Y]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 234 |
| Description: | FGATE ON error: M The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [M]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 235 |
| Description: | FGATE OFF error: M • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [M]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 236 |
| Description: | FGATE ON error: C The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [C]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 237 |
| Description: | FGATE OFF error: C • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [C]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 240 |
| Display: | Service call 240: Error |
| Description: | LD error |
| Causes: | The IPU (EGB) detects a problem at the LD unit. |
| Remedy: | • Worn-out LD • Disconnected or broken harness of the LD. 1. Replace the laser optics unit. |
| Error code: | 241 |
| Display: | Service call 241:Error |
| Description: | LD error: Y The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 242 |
| Display: | Service call 242:Error |
| Description: | LD error: M The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 243 |
| Description: | LD error: C The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 285 |
| Description: | Line position adjustment (MUSIC) error Line position adjustment fails four consecutive times. |
| Causes: | Pattern sampling error (insufficient image density). Defective TD sensors for the line position adjustment. Defective image transfer belt unit. Defective PCDU(s). Defective laser optics housing unit. |
| Remedy: | • Check and reinstall the image transfer belt unit and PCDUs. • Check if each toner bottle has enough toner. • Replace the TD sensor. • Replace the image transfer belt unit. • Replace the PCDU(s). • Replace the laser optics housing unit. |
| Error code: | 290 |
| Description: | Shutter sensor time over error: Close The shutter close sensor does not detect "ON" for 2000 msec after the shutter motor turns on |
| Causes: | • Defective shutter close sensor • Disconnected or broken harness • Defective shutter motor • Defective shutter • Shutter motor overload • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the shutter on the laser optics housing unit. 3. Replace the shutter motor. 4. Replace the shutter close sensor. 5. Replace the IOB. |
| Error code: | 291 |
| Description: | Shutter overrun error 1: Close The shutter close sensor loses the "ON" signal after the shutter was closed. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 292 |
| Description: | Shutter overrun error 2: Close The shutter close sensor detects "ON" after SC 291 has occurred. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 293 |
| Description: | Shutter sensor time over error: Open The shutter open sensor does not detect "ON" for 2000 msec after the shutter motor turns on. |
| Causes: | • Defective shutter close sensor • Disconnected or broken harness • Defective shutter motor • Defective shutter • Shutter motor overload • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the shutter on the laser optics housing unit. 3. Replace the shutter motor. 4. Replace the shutter close sensor. 5. Replace the IOB. |
| Error code: | 294 |
| Description: | Shutter overrun error 1: Open The shutter open sensor loses the "ON" signal after the shutter was closed. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 295 |
| Description: | Shutter overrun error 2: Open The shutter open sensor detects "ON" after SC 291 has occurred. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 296 |
| Description: | Shutter open/close sensor error Both shutter open sensor and close sensor detect "ON" at the same time. |
| Causes: | • Broken harness(es) of the shutter open/close sensors |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 300 |
| Description: | High voltage power output error |
| Causes: | The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit). |
| Remedy: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB. |
| Error code: | 301 |
| Description: | Fuser web must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 303 |
| Display: | SYSTEM HALT (*) 303 : PCB MAIN ET |
| Description: | AC charge output error [Y] The measured voltage is not proper when IOB measures the charge output for each color. |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 360 |
| Display: | Set duplex unit 360: Duplex unit is open. |
| Description: | When duplex unit is removed from printer. |
| Causes: | Does error recover by resetting duplex unit? |
| Remedy: | Normal. Replace duplex unit or engine board. |
| Error code: | 361 |
| Description: | TD sensor (Vt high) error 1: M • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 362 |
| Description: | TD sensor (Vt high) error 1: C • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 363 |
| Description: | TD sensor (Vt high) error 1: Y • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 364 |
| Description: | TD sensor (Vt low) error 2: K The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 365 |
| Description: | TD sensor (Vt low) error 2: M The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 366 |
| Description: | TD sensor (Vt low) error 2: C The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 367 |
| Description: | TD sensor (Vt low) error 2: Y The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 372 |
| Display: | Check DUPLEX 372: Paper jam |
| Causes: | Check miss-feed in duplex unit. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace duplex unit. |
| Error code: | 373 |
| Description: | TD sensor adjustment error: M During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 374 |
| Description: | TD sensor adjustment error: C During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 375 |
| Description: | TD sensor adjustment error: Y During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 380 |
| Display: | Open front cover 380: Paper jam |
| Description: | Paper jam during paper feed from cassette 1, 2, 3, 4 or 5 |
| Causes: | Check miss-feed in duplex unit. |
| Remedy: | Remove miss-fed paper and set cassette. Check/replace cassette 1, 2, 3, 4, or 5. |
| Error code: | 396 |
| Description: | Black drum motor error |
| Causes: | The LOCK signal error is detected when the EGB monitors the black drum motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the black drum motor. Replace it if necessary.e hig |
| Error code: | 397 |
| Description: | Color drum motor error |
| Causes: | The LOCK signal error is detected when the EGB monitors the color drum motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the color drum motor. Replace it if necessary. |
| Error code: | 398 |
| Description: | Drum/Development motor error: C The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on. |
| Causes: | • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system |
| Remedy: | 1. Check or replace the harness. 2. Replace the drum/development motor. 3. Replace the 24V fuse on the PSU. |
| Error code: | 399 |
| Description: | Drum/Development motor error: Y The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on. |
| Causes: | • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system |
| Remedy: | 1. Check or replace the harness. 2. Replace the drum/development motor. 3. Replace the 24V fuse on the PSU. |
| Error code: | 400 |
| Display: | Open top cover 400: Paper size error |
| Description: | TM sensor error |
| Causes: | The CPU detected a low voltage of the positive reflection output under the threshold in the TM sensor. |
| Remedy: | • TM sensors are dirty. • A solid print out due to an electrostatic charging error • The TM sensor is defective. 1. Clean the TM sensors. 2. Replace the TM sensors. 3. Check the image transfer unit. 4. Turn the power Off and On. |
| Error code: | 441 |
| Description: | Image transfer unit motor error When the motor is ON, the machine monitors the lock signals every 100 ms. If the High status occurs 20 times consecutively, the machine judges that the motor is not rotating correctly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Shorted 24 V fuse on the PSU. Defective interlock systeme PSU. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system |
| Error code: | 442 |
| Description: | Image transfer belt contact motor error The image transfer belt contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates. |
| Causes: | Motor overload. Defective motor. Loose connection. Disconnected harness. Shorted 24 V fuse on the PSU. Defective interlock system. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Replace the interlock switch. • Replace the IOB. |
| Error code: | 443 |
| Description: | Image transfer unit error The machine detects the encoder sensor error. |
| Causes: | Defective encoder sensor. Defective image transfer unit motor. Image transfer unit installation error. Loose connection. Broken harness. |
| Remedy: | • Replace the image transfer unit. • Replace the image transfer unit motor. • Reinstall the image transfer unit. • Replace the encoder sensor. • Reconnect the connector. • Replace the harness. |
| Error code: | 452 |
| Description: | Paper transfer unit contact error The paper transfer unit contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates. |
| Causes: | Motor overload. Defective motor. Loose connection. Disconnected harness. Shorted 24 V fuse on the PSU. Defective interlock system. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system. • Replace the IOB. |
| Error code: | 460 |
| Description: | DC Separation Corona Output Error A dc separation feedback voltage of less than 0.5 V was detected after more than 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 490 |
| Display: | Set 490: No paper in MP tray (* stands for A4 B4, etc.) |
| Description: | ITB (Image Transfer Belt) Unit Set Error |
| Causes: | The TM sensor does not detect the reflection from the ITB. |
| Remedy: | • No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S |
| Error code: | 491 |
| Description: | High voltage power: Drum / development bias output error An error signal is detected for 200 ms when charging the drum or development. |
| Causes: | High voltage leak. Loose connection. Broken harness. Defective drum unit or development unit. Defective high voltage supply unit. |
| Remedy: | • Turn the main power switch off and on. • Reattach/replace the harness and parts on the high voltage power supply route. • Replace the drum unit or development unit. • Replace the high voltage supply unit. |
| Error code: | 492 |
| Description: | High voltage power: Image transfer / paper transfer bias output error An error signal is detected for 200 ms when charging the separation, image transfer bet or paper transfer roller. |
| Causes: | High voltage leak. Broken harness Defective image transfer belt unit or paper transfer unit. Defective high voltage supply unit. |
| Remedy: | • Turn the main power switch off and on. • Reattach/replace the harness and parts on the high voltage power supply route. • Replace/reinstall the high-voltage supply unit. • Replace the high voltage supply unit. |
| Error code: | 498 |
| Description: | Temperature and humidity sensor error 2 Thermal sensor output error: If the output value is 0.5 V or lower or 3.0 V or higher, it is judged as a sensor error and the presumptive temperature, 23C, is applied. Humidity sensor output error: If the output value is 2.4V or higher, it is judged as a sensor error and the presumptive humidity, 50 % RH, is applied. If a sensor error is judged to have occurred to the thermal sensor or humidity sensor three times consecutively, the machine issues SC498-00. * However, if the power is switched off and then back on, the machine resumes its attempt to use the sensor. * If the thermal sensor or humidity sensor remains capable of normal operation even after the SC is issued, the capable sensor will keep operating. |
| Causes: | Loose connection/harness disconnected. Defective sensor. |
| Remedy: | • Reconnect to the connector. • Check the harness. |
| Error code: | 501 |
| Display: | Service Call 501: Error |
| Description: | Tray 1 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503-02 |
| Description: | Tray 3 error (Paper Tray Unit, Paper Feed Unit or LCT) This SC is generated if the following condition occurs 3 consecutive times. For the two-tray paper feed unit or one-tray paper tray unit: • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. For the LCT: • When the main switch is turned on or when the LCT is set, if the end fence is not in the home position (home position sensor ON), the tray lift motor stops. • If the upper limit does not go off for 1.5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on. |
| Causes: | For the two-tray paper feed unit or one-tray paper tray unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 504-01 |
| Description: | Tray 4 error (Paper Tray Unit, Paper Feed Unit or LCT) For the two-tray paper feed unit or one-tray paper tray unit When the tray lift motor is turned on, the upper limit is not detected within 10 seconds. For the LCT If the upper or lower limit is not detected within 8 seconds when the tray lift motor is turned on to lift up or lower the tray |
| Causes: | • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 504-02 |
| Description: | Tray 4 error (Paper Tray Unit, Paper Feed Unit or LCT) This SC is generated if the following condition occurs 3 consecutive times. For the two-tray paper feed unit or one-tray paper tray unit • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. For the LCT • If the upper limit does not go off for 1.5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on. |
| Causes: | For the two-tray paper feed unit or one-tray paper tray unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 529 |
| Description: | Junction gate 1 motor error The junction gate 1 HP sensor does not detect the home position of junction gate 1 for 0.15 seconds when the machine starts to detect its home position. The junction gate 1 HP sensor does not turn off for 0.15 seconds after the machine has detected its home position. |
| Causes: | • Disconnected or defective junction gate 1 motor • Disconnected or defective junction gate 1 HP sensor • Mechanical problem (such as paper jam etc.) • Shorted 24 V fuse on the PSU • Defective IOB |
| Remedy: | 1. Remove any objects that obstruct junction gate 1. 2. Replace the junction gate 1 HP sensor. 3. Replace the junction gate 1 motor. 4. Replace the 24 V fuse on the PSU. 5. Replace the IOB. |
| Error code: | 530 |
| Description: | LSU Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the LSU fan motor. |
| Error code: | 531 |
| Description: | Fusing Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the fusing fan motor. |
| Error code: | 532 |
| Description: | IH coil fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH coil fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH coil fan motor • Defective IH coil fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH coil fan. 3. Replace the IOB. |
| Error code: | 533 |
| Description: | IH inverter fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH inverter fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH inverter fan motor • Defective IH inverter fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH inverter fan. 3. Replace the IOB. |
| Error code: | 534 |
| Description: | Second duct fan error The machine does not detect the fan motor lock signal for 2 seconds while the second duct fan turns on. |
| Causes: | • Disconnected harness • Overload on the second duct fan motor • Defective second duct motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the second duct fan. 3. Replace the IOB. |
| Error code: | 535 |
| Description: | Paper exit fan error The lock sensor value is monitored every 100 ms when the motor is ON. If the retrieval of the lock signal fails 100 times consecutively, it is determined as a failure to rotate properly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 540 |
| Description: | Fusing/Paper exit motor error At the fusing delivery brushless motor, the lock signal is monitored every 100 ms. If the High status occurs consecutively 20 times, it is determined as a failure to rotate properly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Shorted 24 V fuse on the PSU. Defective interlock system. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 548 |
| Description: | Low Temperature Error |
| Causes: | The center thermistor detects 100°C or less for 4 seconds. |
| Remedy: | • Defective fusing lamp • Defective thermistor 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.d |
| Error code: | 549 |
| Description: | Fusing heater connection error The fusing sleeve belt rotation sensor detects the target temperature as 50°C for 5 seconds or more after the fusing/paper exit motor has turned on. |
| Causes: | Broken heater cables. Loose connection. |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 554 |
| Description: | Fusing sleeve belt overheat: End (hardware error) The fusing sleeve belt thermistor detects 250°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 561 |
| Description: | Pressure roller end thermistor error 1 During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the end thermistor on the pressure roller returned a digital reading of more than 3.3V. |
| Causes: | • Pressure roller end thermistor not positioned properly • Pressure roller end thermistor connector loose, broken, defective • Pressure roller end thermistor defective • MCU defective |
| Error code: | 562 |
| Description: | Pressure roller temperature error The temperature of the pressure roller does not reach the ready temperature for 120 seconds after the fusing lamp has turned on. |
| Causes: | • Defective pressure roller thermistor • Defective fusing lamp |
| Remedy: | 1. Clean the thermopile. 2. Replace the thermistor for the pressure roller. 3. Replace the pressure roller fusing lamp. |
| Error code: | 563 |
| Description: | Pressure roller end thermistor error 2 During the hot roller temperature control sequence, the end thermistor on the pressure roller returned a digital reading of less than 0.2V. |
| Causes: | • Pressure roller end thermistor connector loose • Pressure roller end thermistor short circuit, defective • MCU defective |
| Error code: | 564 |
| Description: | Pressure roller overheat: End (hardware error) The thermistor detects 240°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: • The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 565 |
| Description: | Pressure roller fusing lamp consecutive full power 3 When the fusing unit is not running in the ready condition, the pressure roller fusing lamp keeps ON full power for 180 seconds or more. |
| Causes: | • Broken pressure roller fusing lamp |
| Remedy: | 1. Replace the pressure roller fusing lamp. 2. Replace the pressure roller thermistor. 3. Replace the PSU. |
| Error code: | 580 |
| Description: | IH inverter zero cross frequency error The zero cross signal is not detected for 1 second or more after the IH inverter has turned on. |
| Causes: | • Disconnected CN983 on the IH inverter • Defective IH inverter • Defective IH coil unit |
| Remedy: | 1. Check CN983 on the IH inverter. 2. Replace the IH inverter. 3. Replace the IH coil unit. |
| Error code: | 581 |
| Description: | NC sensor broken: Center The sensor detects -17°C or less for 6 seconds |
| Causes: | Defective thermopile. Defective thermistor. Loose connection. |
| Error code: | 582 |
| Description: | IH inverter current error at power on The output current from the IH inverter does not reach the proper value when the IH inverter turns on. |
| Causes: | • Disconnected power input terminal 1 and 2 • Defective IH inverter • Defective IH coil unit • Defective fusing unit |
| Remedy: | 1. Check the power input terminals 1 and 2. 2. Replace the IH inverter. 3. Replace the IH coil unit. 4. Replace the fusing unit. |
| Error code: | 583 |
| Description: | IH inverter communication error The IH inverter does not get the communication signal from the IOB. |
| Causes: | • Broken connection between IH inverter and IOB • Defective IH inverter • Defective IOB • Defective EGB |
| Remedy: | 1. Check the connection between IH inverter and IOB 2. Replace the IH inverter. 3. Replace the IOB. 4. Replace the EGB. |
| Error code: | 584 |
| Description: | Fusing unit rotation error The fusing belt sensor does not detect a change in the fusing unit actuator for 0.5 seconds. |
| Causes: | • Defective fusing/paper exit motor • Deformed actuator for the fusing belt sensor • Defective fusing belt sensor • Broken connection between IH inverter and IOB • Incorrectly set fusing unit |
| Remedy: | 1. Check if the fusing unit is correctly set. 1. Check or replace the actuator for fusing belt sensor. 2. Replace the fusing belt sensor. 3. Replace the IH inverter. 4. Check the connection between IH inverter and IOB. |
| Error code: | 585 |
| Description: | IH coil unit full power (1250W) error The IH coil unit full power (1250W) continues for 220 seconds or more. |
| Causes: | • Defective IH inverter • Defective EGB • Defective IOB • Broken connection between IH inverter and IOB • Defective thermopile |
| Error code: | 586 |
| Description: | IH coil unit rare short error The IH inverter detects an unusual current (high current) in the IH coil unit. |
| Causes: | • Defective IH coil unit • Defective IH inverterl unit |
| Remedy: | 1. Replace the IH coil unit. 2. Replace the IH inverter. |
| Error code: | 587 |
| Description: | IH inverter high temperature error The IH inverter detects a high temperature near Q5 (power control circuit on the IH inverter). |
| Causes: | • Defective IH inverter • Defective IH inverter fan • Clogged IH inverter fan intake at the right rear cover • Incorrect input paper type to the machine |
| Remedy: | 1. Check or clean the IH inverter fan intake. 2. Set the correct paper type on the operation panel. 3. Replace the IH inverter. 4. Replace the IH inverter fan. |
| Error code: | 610 |
| Display: | ERROR 610 NOT FILLUP |
| Description: | Mechanical counter error: Bk This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 611 |
| Display: | ERROR 611 Case Weight |
| Description: | Mechanical counter error: FC This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 622 |
| Description: | Paper Bank communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The paper bank`s control board is faulty. Defective BCU/IOB. The paper bank`s connection is faulty. |
| Remedy: | • Reconnect the paper bank cables. • Replace the BCU. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 630 |
| Description: | CSS communication error A communication error occurred during communication with the CSS. |
| Causes: | • Communication line error |
| Remedy: | Logging only. |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 633 |
| Description: | Key/card counter device error 2 During communication with the device, the MCU received a break (Low) signal. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 650 |
| Description: | @Remote communication error 1 A dial-up or modem error occurred during @Remote operation. (This error occurs only during @Remote operation.) |
| Causes: | • Modem line disconnected • Modem board missing or not properly installed |
| Error code: | 651 |
| Description: | @Remote communication error 2 An illegal dial-up to the service center was attempted by @Remote. |
| Causes: | • Software bug |
| Error code: | 669 |
| Description: | EEPROM Error |
| Causes: | An unexpected value exists in the initialization flag of the EEPROM |
| Remedy: | • EEPROM not initialized • Defective EEPROM |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 681 |
| Description: | Toner bottle ID: Communication error -01 D Device ID is not identified: K -02 D Device ID is not identified: M -03 D Device ID is not identified: C -04 D Device ID is not identified: Y -06 D Channel error: K -07 D Channel error: M -08 D Channel error: C -09 D Channel error: Y -11 D Device error: K -12 D Device error: M -13 D Device error: C -14 D Device error: Y -16 D Communication interruption (an error during communication): K -17 D Communication interruption (an error during communication): M -18 D Communication interruption (an error during communication): C -19 D Communication interruption (an error during communication): Y -21 D Communication time-out: K -22 D Communication time-out: M -23 D Communication time-out: C -24 D Communication time-out: Y -26 D Device operation suspended (logically suspended): K -27 D Device operation suspended (logically suspended): M -28 D Device operation suspended (logically suspended): C -29 D Device operation suspended (logically suspended): Y -31 D The requested buffer is full: K -32 D The requested buffer is full: M -33 D The requested buffer is full: C -34 D The requested buffer is full: Y -36 D No error code: K -37 D No error code: M -38 D No error code: C -39 D No error code: Y |
| Causes: | Communication error occurs when the toner bottle ID starts to communicate with the toner bottle ID receptor. Retry of toner bottle ID communication fails three times after the machine has detected the toner bottle ID communication error. • 01-04 Damaged memory chip data • 06-09 Disconnected interface • 11-14 No memory chip on the toner cartridge • 16-9, 21-24, 26-39 Caused by noise • 31-34, 36-39 Software problem • Replace the toner bottle detection board. • Replace the toner cartridge. • Turn the main power switch off and on. |
| Error code: | 682 |
| Description: | Memory chip at TD sensor: Communication error |
| Causes: | • 01-04 Damaged memory chip data • 06-09 Disconnected interface • 11-14 No memory chip on the toner cartridge • 16-19, 21-24, 26-39 Caused by noise • 31-34, 36-39 Software problem |
| Remedy: | • Replace the PCU. • Turn the main power switch off and on. |
| Error code: | 683 |
| Description: | RFID: Unit check error The machine gets RFID communication error even the toner cartridges have not been installed in the machine |
| Causes: | Caused by noise |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 689 |
| Description: | IH inverter communication error • When the machine turns on, recovers from the energy save mode or front and right doors are opened and closed, a time out error for communicating with the IOB occurs. • The IOB detects the break signal from the IH inverter after a communication between the IOB and IH inverter has already been detected. • The IOB fails to communicate with IH inverter three times after the IOB has detected the break signal from the IH inverter. |
| Causes: | • Defective IOB • Defective IH inverter. |
| Remedy: | 1. Turn the main power switch off and on. 2. If the error occurs again, replace the IOB and/or the IH inverter. |
| Error code: | 690 |
| Description: | GAVD Communication Error |
| Causes: | The ID of the GAVD is not identified during initialization. The chip ID of the GAVD cannot be detected by the machine at power-on. |
| Remedy: | • Defective EGB 1. Replace the EGB. EE |
| Error code: | 700 |
| Description: | Original stopper HP error When the pick-up motor turns on clockwise, the original stopper HP sensor does not detect the home position of the original stopper. |
| Causes: | • Detached timing belt for the pick-up motor • Defective original stopper HP sensor • Defective pick-up motor • Defective DF drive board |
| Remedy: | 1. Check the timing belt for the pick-up motor. 2. Replace the DF drive board if the pick-up motor does not work correctly. 3. Replace the pick-up motor. 4. Replace the original stopper HP sensor. |
| Error code: | 701 |
| Description: | ADF Pickup Roller Release Malfunction (D016/D097 only) The pick-up roller HP sensor does not activate or de-activate when the pick-up motor turns on. |
| Causes: | • HP sensor connector, harness loose, broken, defective • Pick-up motor connector, harness loose, broken defective • Pick-up roller HP sensor defective • Pick-up motor defective • ADF main control board defective |
| Remedy: | 1. Check the harness connections. 2. Replace the pick-up roller HP sensor. 3. Replace the pick-up motor. 4. Replace the main board of the ADF. |
| Error code: | 725 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor. 4. Replace the finisher main board. |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 740 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished after a certain time. For the 1000-sheet booklet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 741 |
| Description: | Finisher corner stapler rotation motor error The stapler does not return to its home position within the specified time after stapling. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective stapler rotation motor • Overload to the stapler rotation motor • Defective stapler rotation HP sensor |
| Remedy: | 1. Replace the stapler rotation motor. 2. Replace the stapler rotation HP sensor. |
| Error code: | 742 |
| Description: | Finisher stapler movement motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished for a certain time. For the 1000-sheet booklet finisher • The stapler HP sensor is not activated within the specified time after the stapler motor turned on. (first detection: jam error, consecutive twice detection SC code). |
| Causes: | • Motor overload • Loose connection of the stapler home position sensor • Loose connection of the stapler movement motor • Defective stapler home position sensor • Defective stapler movement motor |
| Remedy: | 1. Check the connection of the stapler movement motor. 2. Check the connection of the stapler home position sensor. 3. Replace the stapler home position sensor. 4. Replace the stapler movement motor. |
| Error code: | 743 |
| Description: | Booklet stapler motor error 1 The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher The front stapler unit saddle-stitch motor does not start operation within the specified time. |
| Causes: | • Motor overload • Loose connection of the front stapler motor • Defective front stapler motor |
| Remedy: | Replace the front stapler motor. |
| Error code: | 744 |
| Description: | Booklet staple motor error 2 The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher The rear stapler unit saddle-stitch motor does not start operation within the specified time. |
| Causes: | • Motor overload • Loose connection of the rear stapler motor • Defective rear stapler motor |
| Remedy: | Replace the front stapler motor. |
| Error code: | 746 |
| Description: | 1000-sheet booklet finisher: Stack feed motor error • The stack feed HP sensor does not detect "ON" twice (once: jam error) for specified time after the stack feed motor has turned on. • The stack feed HP sensor does not detect "OFF" twice (once: jam error) for specified time after the stack feed motor has turned on. |
| Causes: | • Motor overload • Loose connection of the stack feed motor • Defective stack feed motor |
| Remedy: | 1. Check the connections and cables for the stack feed motor and HP sensor. 2. Check for blockages in the stack feed motor mechanism. 3. Replace the stack feed HP sensor and/or stack feed motor 4. Replace the finisher main board. |
| Error code: | 750 |
| Description: | 1000/3000-sheet (booklet) finisher: Tray lift motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. |
| Causes: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor |
| Remedy: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor. |
| Error code: | 760 |
| Description: | Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Punch HP sensor disconnected, defective • Punch motor disconnected or defective • Punch motor overload due to obstruction |
| Remedy: | 1. Check the connections and cables for the punch motor and HP sensor. 2. Check for blockages in the punch motor mechanism. 3. Replace the punch HP sensor and/or punch motor 4. Replace the finisher main board. |
| Error code: | 761 |
| Description: | Finisher folder plate motor error The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Remedy: | 1. Check the connections and cables for the folder plate motor and HP sensor. 2. Check for blockages in the folder plate motor mechanism. 3. Replace the folder plate HP sensor and/or folder plate motor 4. Replace the finisher main board. |
| Error code: | 763 |
| Description: | Rear fold plate HP sensor error The state (on/off, off/on) of the rear fold plate HP sensor in the fan fold unit did not change 1 sec. after the plate started to move. |
| Causes: | • Fold plate motor (R) harness connector loose, disconnected, broken • Rear fold plate HP sensor harness connector loose, disconnected, broken • Fold plate motor (R) defective • Rear fold plate HP sensor defective • Undetected paper is jamming the action of the motor or fold plate • Fan folder unit MCU defective |
| Error code: | 764 |
| Description: | Paper position sensor slide motor error The paper position sensor moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the paper position sensor slide motor. 2. Replace the paper position sensor slide motor. |
| Error code: | 791 |
| Description: | Bridge unit error The machine recognizes the finisher, but does not recognize the bridge unit. |
| Causes: | The bridge unit is not installed. Defective bridge unit. Re-install the bridge unit. Turn the main power switch off and on. |
| Remedy: | • Re-install the bridge unit. • Turn the main power switch off and on. |
| Error code: | 792 |
| Description: | Finisher error The machine does not recognize the finisher, but recognizes the bridge unit. |
| Causes: | The finisher`s connection is faulty. The finisher is not attached to a device equipped with the bridge unit. Defective finisher. |
| Remedy: | Reconnect the finisher or bridge unit, and then turn the main power switch off and then back on. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855, 856 |
| Description: | Wireless LAN/Bluetooth card error An error is detected in the wireless LAN/Bluetooth card. |
| Causes: | • Loose connection • Defective wireless LAN/Bluetooth card |
| Remedy: | 1. Check the connection. 2. Replace the wireless LAN/Bluetooth card. |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 877 |
| Description: | HDD Data Erase Error The Data Overwrite Security option cannot scramble and erase data on the HDD because the DOS SD card has been corrupted or has |
| Causes: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not been removed from the SD card slot. |
| Remedy: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not solve the problem, the SD card has been damaged.) • Install a new NVRAM • Install a new Data Overwrite Security option with a new SD card |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 910...914 |
| Description: | External Controller Error |
| Causes: | The external controller alerted the machine about an error. |
| Remedy: | 1. Please refer to the instructions for the external controller (application). |
| Error code: | 919 |
| Display: | Power Off/on 919: Error |
| Description: | Power Supply Fan Error |
| Causes: | • Controller RW3600 power outtage • Controller RW3600 rebooted • Connection to Controller RW3600 loose |
| Remedy: | 1 Is CN17 on the printer controller board properly connected? Go to step 2. Connect CN17. 2 Is CN6 on the CK2 daughter board properly connected? Go to step 3. Connect CN6. 3 Is +24 V present between pins 1 and 3 of connector CN6 on the CK2 daughter board? Replace the power supply fan. Replace the printer controller board. 4 Did either exchange solve the problem? Problem solved. Replace the CK2 daughter board. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 994 |
| Display: | Service Call 994:Error |
| Description: | Density Sensor Error |
| Causes: | • No action required because this SC does not interfere with operation of the machine. |
| Remedy: | 1 Is the front door fully closed? Go to step 2. Close the front door. 2 Is the density sensor actuator stuck in place? Release the density sensor actuator. Go to step 3. 3 Are connectors CN406 and CN407 on the sensor board connected properly? Go to step 4. Plug the connector in securely. 4 Is connector CN15 on the printer controller board connected properly? Replace the density sensor. Go to step 5. Plug the connector in securely. 5 Did replacing the density sensor fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 995 |
| Description: | Finisher Main Feed Motor abnormal |
| Causes: | -01 D • Defective BCU • NVRAM Replacement error • Install the previous NVRAM • Input the serial number with SP5-811-004, and turn the main power switch off and on. -02 D • Defective NVRAM • Defective controller Perform SP5-825 to download the appropriate data to the NVRAM, and then turn the main power switch off and then back on. -03 D The serial number cannot be identified due to a mistake during controller replacement or mechanical failure. Replace the controller with the correct type. -04 D - Place all parts in the initial state, and then replace the parts according to the procedures described in the manuals. |
| Remedy: | 1 Is there jammed paper or other obstructions in the paper path? Clear the paper path. Go to step 2. 2 Check to ensure the connector PJ6 on the finisher control board and the feed motor assembly cable are properly connected. Are the cables properly connected? Go to step 3. Properly connect the cables. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pins 7 and 8 and +5 V dc (–10%) between pins 7 and 6 on the feed motor assembly cable connector CN1. Is either voltage missing? Go to step 4. Go to step 5. 4 Disconnect the feed motor assembly cable and PJ6 on the finisher control board. Measure continuity on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 5 Replace the feed motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 6 Measure for +24 V dc between pins 1 and 2 on connector PJ3 on the finisher control board. Measure for +5 V dc between pins 1 and 3 on PJ2 on the finisher control board. Is either voltage missing? Replace the power supply. Replace the finisher control board. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
Парткод
Название
RICOH TYPE K Скрепки с картриджем
RICOH TYPE K Скрепки (3 упаковки)
RICOH TYPE L Скрепки буклетные в картридже
RICOH TYPE L Скрепки буклетные (в упаковке 4*2000шт.)
RICOH TYPE MPC4500E Тонер-картридж черный
RICOH TYPE MPC4500E Тонер-картридж желтый
RICOH TYPE MPC4500E Тонер-картридж пурпурный
RICOH TYPE MPC4500E Тонер-картридж голубой
RICOH Блок проявки черный с девелопером
RICOH Блок проявки пурпурный с девелопером
RICOH Блок проявки голубой с девелопером
RICOH Блок проявки желтый с девелопером
RICOH Узел термозакрепления (печка)
(B2232027) RICOH Блок фотобарабанов цветной CMY
(B2232042) RICOH Блок фотобарабана черный
RICOH Девелопер черный
RICOH Девелопер голубой
RICOH Девелопер пурпурный
RICOH Девелопер желтый
