Ricoh MPC6000SP
Рейтинг
Модули
Tonner Supply 3
Frame Section 3
TRANSFER BELT UNIT 3
ELECTRICAL SECTION 5
ELECTRICAL SECTION 1
EXTERIOR 1
Transfer Entrance 2
DRIVE SECTION 2
Drive Section 1
DEVELOPMENT UNIT
Paper Transfer 2
ARDF Drive & Electrical 2
ARDF Drive & Electrical 1
TANDEM TRAY 1
FRAME SECTION 2
OPTICS SECTION 4
Original Exit 2
Frame Section 4
Fusing Unit 6
DUPLEX UNIT 4
ARDF Exterior
OPTICS SECTION 3
VERTICAL TRANSPORT
Transfer Entrance 3
Used Tonner Section 1
ELECTRICAL SECTION 4
Original Feed 2
Paper Exit 1
Transfer Cover
PAPER REGISTRATION 2
ELECTRICAL SECTION 2
ELECTRICAL SECTION 3
EXTERIOR 2
FUSING UNIT 3
FRAME SECTION 1
Drive Section 5
Tonner Supply 1
Original Exit 1
Original Trans 2
Fusing Unit 5
Transfer Belt Cleaning 2
OPTICS SECTION 2
DRIVE SECTION 4
PCU 2
FUSING UNIT 1
PCU 3
Paper Exit 3
DUPLEX UNIT 1
By-pass Feed 1
DRIVE SECTION 3
TRANSFER BELT UNIT 2
TANDEM TRAY 2
Frame Section 5
ARDF Original Tray
ELECTRICAL SECTION 8
OPTICS SECTION 1
TANDEM TRAY 3
Universal Tray 1
OPERATION PANEL
ELECTRICAL SECTION 7
FUSING UNIT 2
TRANSFER BELT UNIT 1
ELECTRICAL SECTION 6
PAPER REGISTRATION 1
Transfer Entrance 1
ARDF Frame
DUPLEX UNIT 2
DUPLEX UNIT 3
Tonner Supply 2
Paper Exit 4
Original Trans 1
Paper Transfer 1
Transfer Belt Cleaning 1
Fusing Unit 4
DUPLEX UNIT 5
Fusing Unit 7
By-pass Feed 2
Universal Tray 2
Original Trans 3
Drive Section 6
LASER UNIT
Paper Exit 2
Used Tonner Section 2
Original Feed 1
PCU 1
Детали Original Trans 2
| Деталь: | Supporting Plate:Side Plate |
| Парткод: | B132 3217 |
| Деталь: | Brushless Motor:DC24V 18W |
| Парткод: | AX06 0356 |
| Деталь: | Bracket:Fix:Right |
| Парткод: | B132 3218 |
| Деталь: | Filter:Duct |
| Парткод: | B132 2475 |
| Деталь: | Cover:Lower:Black |
| Парткод: | B132 3229 |
| Деталь: | Gear:75Z |
| Парткод: | B132 3224 |
| Деталь: | Shaft:Drive |
| Парткод: | B132 3222 |
| Деталь: | Gear:21/32Z |
| Парткод: | B132 3223 |
| Деталь: | Guide:Shaft:Drive |
| Парткод: | AA08 2139 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 5215 2621 |
| Деталь: | Cover:Drawer |
| Парткод: | B132 3435 |
| Деталь: | Bracket:Drawer |
| Парткод: | B132 3434 |
| Деталь: | Bracket:Cnb |
| Парткод: | D014 3331 |
| Деталь: | PCB:CNB |
| Парткод: | D014 5440 |
| Деталь: | Harness:CNB:Left |
| Парткод: | D014 5228 |
| Деталь: | Harness:Toner Hopper:Uni:Drawer:CNB |
| Парткод: | D014 5227 |
| Деталь: | Harness:Toner Hopper:Fan Motor |
| Парткод: | D014 5233 |
| Деталь: | Stay:Machine or Copier:Left:Peen |
| Парткод: | B132 1115 |
| Деталь: | Cover:Stay:Left |
| Парткод: | B132 1222 |
| Деталь: | Slide Rail:Pull Out:Left |
| Парткод: | AA07 0066 |
| Деталь: | Bracket:Sensor:Entrance |
| Парткод: | B132 7101 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | HARNESS:SENSOR |
| Парткод: | D014 5253 |
| Деталь: | Stud:Guide Pin |
| Парткод: | AA14 3421 |
| Деталь: | Guide Plate:Left Lower:Assy |
| Парткод: | B132 7114 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3907 |
| Деталь: | Stopper:Pressure |
| Парткод: | B132 7038 |
| Деталь: | Slide Rail:Toner Supply:Assy |
| Парткод: | AA07 0064 |
| Деталь: | Stay:Slide Rail:Toner Supply |
| Парткод: | B132 3486 |
| Деталь: | Guide:Registration:Open And Close |
| Парткод: | B132 2718 |
| Деталь: | Slide Rail:Pull Out:Right |
| Парткод: | AA07 0067 |
| Деталь: | Stay:Machine Or Copier:Right Lower |
| Парткод: | B132 1004 |
| Деталь: | Knob Screw:Hdd Unit |
| Парткод: | G104 5139 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Guide Plate:Connecting:LCT |
| Парткод: | D014 2637 |
| Деталь: | Left Gasket - Front Rear |
| Парткод: | B010 1289 |
| Деталь: | Bracket:Fix:Manual Feed |
| Парткод: | B132 2815 |
| Деталь: | Bushing:6x8x5 |
| Парткод: | AA08 0265 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0960 |
| Деталь: | Guide Plate:LCT:Open And Close |
| Парткод: | D014 2662 |
| Деталь: | Bracket:Sensor:Large Capacity Tray |
| Парткод: | B132 2654 |
| Деталь: | Harness:Paper Feed Unit:LCT:Sensor |
| Парткод: | D014 5250 |
| Деталь: | Bracket:Cover:LCT |
| Парткод: | B132 1008 |
| Деталь: | Power Pack:T1/T2 |
| Парткод: | AZ32 0170 |
| Деталь: | Insulating Sheet:Power Pack: Intermediate Tran |
| Парткод: | D014 6145 |
| Деталь: | Guard:Right |
| Парткод: | B132 6170 |
| Деталь: | Guard:Left |
| Парткод: | B132 6171 |
| Деталь: | Guard:Rear |
| Парткод: | B132 6172 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Spring Plate:Cam |
| Парткод: | B132 6124 |
| Деталь: | Stopper:On-Off |
| Парткод: | B132 6157 |
| Деталь: | DUCT |
| Парткод: | B132 6121 |
| Деталь: | Harness:Density Sensor |
| Парткод: | D014 5237 |
| Деталь: | Positioning Sensor |
| Парткод: | AW01 0141 |
| Деталь: | Bracket:Positioning Sensor: Intermediate Trans |
| Парткод: | D014 6122 |
| Деталь: | Stand |
| Парткод: | B132 6156 |
| Деталь: | Harness:Transfer Belt Unit |
| Парткод: | D014 5376 |
| Деталь: | Harness:18Pin |
| Парткод: | D014 5377 |
| Деталь: | Grip:Application |
| Парткод: | B712 5605 |
| Деталь: | Plate:Bracke |
| Парткод: | B132 6165 |
| Деталь: | Decal:Main Switch Display:On |
| Парткод: | B132 1553 |
| Деталь: | Decal - Main Switch Display:Off |
| Парткод: | B132 1555 |
| Деталь: | Inner Cover:Main Switch |
| Парткод: | B132 1551 |
| Деталь: | Shaft:Micro Switch:Front |
| Парткод: | B132 5855 |
| Деталь: | Lever:Micro Switch |
| Парткод: | B132 5853 |
| Деталь: | Safety switch spring |
| Парткод: | A257 1165 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 1012 |
| Деталь: | Bracket:Main Switch |
| Парткод: | B132 5851 |
| Деталь: | Screw:Micro Switch |
| Парткод: | B132 5852 |
| Деталь: | Duct:Main:Vacuum |
| Парткод: | D014 6876 |
| Деталь: | Fan Motor:Mm60:25mm:DC24V 4.8W |
| Парткод: | AX64 0150 |
| Деталь: | Duct:Heat Sinker |
| Парткод: | D014 6871 |
| Деталь: | Humidity Control Unit |
| Парткод: | D014 3635 |
| Деталь: | Seal:Fan:Humidity Control |
| Парткод: | B132 2465 |
| Деталь: | Operation Panel Bracket |
| Парткод: | D014 1450 |
| Деталь: | FILTER |
| Парткод: | B132 2468 |
| Деталь: | Duct:Vacuum:Assy |
| Парткод: | B132 6851 |
| Деталь: | Duct:Imaging Unit:Rear:C2:Assy |
| Парткод: | D014 6983 |
| Деталь: | Duct:Imaging Unit:Front:Assy |
| Парткод: | B132 6921 |
| Деталь: | Fan Motor:15mm:24V |
| Парткод: | AX64 0164 |
| Деталь: | Bracket:Connector |
| Парткод: | D014 1020 |
| Деталь: | Bracket:Drawer:Toner Supply |
| Парткод: | B132 3489 |
| Деталь: | Cover:Drawer |
| Парткод: | B132 3491 |
| Деталь: | Bracket:Fix:Toner Supply |
| Парткод: | B132 3493 |
| Деталь: | Duct:Vacuum:Entrance |
| Парткод: | B132 6855 |
| Деталь: | Bracket:Harness:Operation Panel |
| Парткод: | D014 1453 |
| Деталь: | Cover:Connector:Key Counter |
| Парткод: | D014 1514 |
| Деталь: | Duct:Exit:Exhaust |
| Парткод: | D014 6911 |
| Деталь: | Fan:Sirocco:DC24V:2speed |
| Парткод: | AX65 0042 |
| Деталь: | Shield:Sirocco |
| Парткод: | B132 6966 |
| Деталь: | Fan Motor:Mm60:25mm:DC24V 4.8W |
| Парткод: | AX64 0150 |
| Деталь: | Bracket:Drive:Exhaust |
| Парткод: | D014 6852 |
| Деталь: | Duct:Exhaust |
| Парткод: | D014 6861 |
| Деталь: | Harness:DRB:ADF:Power Source |
| Парткод: | D014 5258 |
| Деталь: | Base:Electric Potential Sensor |
| Парткод: | B132 5415 |
| Деталь: | Power Pack:C/G/B |
| Парткод: | AZ32 0169 |
| Деталь: | Harness:Electric Potential Sensor |
| Парткод: | D014 5229 |
| Деталь: | Harness:Sensor:CY |
| Парткод: | D014 5358 |
| Деталь: | Harness:Sensor:KM |
| Парткод: | D014 5357 |
| Деталь: | Relay Duct:Black:PCU |
| Парткод: | D014 3661 |
| Деталь: | Bracket:Stay:Duct:Right |
| Парткод: | B132 2433 |
| Деталь: | Duct:Horizontal:PCU |
| Парткод: | D014 3567 |
| Деталь: | Duct:Exhaust:Color |
| Парткод: | D014 3575 |
| Деталь: | Bracket:Stay:Duct:Horizontal |
| Парткод: | D014 1018 |
| Деталь: | Manual:COPY_REF:NA |
| Парткод: | D015 7652 |
| Деталь: | Manual:About_machine:NA |
| Парткод: | D015 7703 |
| Деталь: | Manual:TROUBLESHOOT:NA |
| Парткод: | D015 7708 |
| Деталь: | O/I Holder - Assembly |
| Парткод: | B027 8521 |
| Деталь: | Cloth Holder |
| Парткод: | B065 1371 |
| Деталь: | Cloth - DF Exposure Glass |
| Парткод: | B065 1374 |
| Деталь: | Sponge:SD-Card:Plate |
| Парткод: | B132 1529 |
| Деталь: | Lever:Guide Plate |
| Парткод: | B132 1511 |
| Деталь: | Holder:Stand |
| Парткод: | B132 1226 |
| Деталь: | Decal - Paper Size |
| Парткод: | B065 8490 |
| Деталь: | Inner Cover:Paper Feed |
| Парткод: | B132 1558 |
| Деталь: | Inner Cover:Paper Feed |
| Парткод: | B132 6761 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | B070 1307 |
| Деталь: | Hinge:Door:Lower:Assy |
| Парткод: | B132 1464 |
| Деталь: | Tray:Holder:PCU |
| Парткод: | B132 2393 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 1012 |
| Деталь: | Holder:PCU |
| Парткод: | B132 2391 |
| Деталь: | Adjusting Pin:Development |
| Парткод: | D014 3144 |
| Деталь: | Decal:Misfeed Removal |
| Парткод: | D014 1550 |
| Деталь: | Decal:Color:Mfp |
| Парткод: | AA00 0239 |
| Деталь: | Panel:Logo |
| Парткод: | B132 1531 |
| Деталь: | Sheet:Logo:INF:C6000 |
| Парткод: | D014 1536 |
| Деталь: | Sheet:Logo:INF:C6000SP |
| Парткод: | D014 1541 |
| Деталь: | Sheet:Logo:INF:C7500 |
| Парткод: | D015 1536 |
| Деталь: | Sheet:Logo:INF:C7500SP |
| Парткод: | D015 1541 |
| Деталь: | Hinge:Door:Upper |
| Парткод: | D014 1455 |
| Деталь: | Door:Front |
| Парткод: | D014 1501 |
| Деталь: | Cover:Main Switch |
| Парткод: | B132 1512 |
| Деталь: | Case:Main Switch |
| Парткод: | B132 1513 |
| Деталь: | Grip:Door:Front |
| Парткод: | B132 1514 |
| Деталь: | Lever:Micro Switch |
| Парткод: | B132 1515 |
| Деталь: | Door Catch |
| Парткод: | B132 1526 |
| Деталь: | Decal:Toner Supply |
| Парткод: | D014 1560 |
| Деталь: | Holder:Cap:Receiving Sub-unit |
| Парткод: | B132 3084 |
| Деталь: | Duct:Door:Front |
| Парткод: | D014 6961 |
| Деталь: | Seal:Duct:Door:Front:Short |
| Парткод: | D014 6967 |
| Деталь: | Seal:Duct:Door:Front:Long |
| Парткод: | D014 6968 |
| Деталь: | Decal - Display:Original Table |
| Парткод: | B652 2378 |
| Деталь: | Decal - Cleaning:Exposure Glass |
| Парткод: | B132 1548 |
| Деталь: | Decal:Caution:Original:5-lang |
| Парткод: | B652 2379 |
| Деталь: | Decal - Power Source:Off |
| Парткод: | B132 1573 |
| Деталь: | Sheet:Logo:TEC:4500C |
| Парткод: | B132 1544 |
| Деталь: | Joint:Drive:Development Unit |
| Парткод: | D014 3135 |
| Деталь: | Decal:Energy-Star |
| Парткод: | AA00 1477 |
| Деталь: | Decal - Cleaning:Exposure Glass |
| Парткод: | B132 1549 |
| Деталь: | Decal:Size Indication:Multi-Language:C3 |
| Парткод: | B234 8510 |
| Деталь: | CD-ROM:SCN:Exp:GEN:Assy |
| Парткод: | D376 6515 |
| Деталь: | CD-ROM:PRN:EU:INF:Assy |
| Парткод: | D376 6526 |
| Деталь: | Sheet:EULA:18Languages |
| Парткод: | D376 7900 |
| Деталь: | Seal:Caution:18Languages |
| Парткод: | D376 7901 |
| Деталь: | Registration Roller:Upper |
| Парткод: | B132 2629 |
| Деталь: | Registration Roller:Lower |
| Парткод: | B132 2617 |
| Деталь: | LED |
| Парткод: | AX56 0011 |
| Деталь: | Harness:LED:Sensor |
| Парткод: | D014 5246 |
| Деталь: | Bracket:Optics Sensor |
| Парткод: | B132 2624 |
| Деталь: | Registration Guide:Lower |
| Парткод: | D014 2610 |
| Деталь: | Ball Bearing - 8x12x5 |
| Парткод: | A247 2800 |
| Деталь: | Spacer - 1x8x12 |
| Парткод: | AA13 2025 |
| Деталь: | Timing Pulley:35T |
| Парткод: | AB03 0302 |
| Деталь: | Pawl:Lock:Front |
| Парткод: | B132 2708 |
| Деталь: | Bushing - 4x6x7mm |
| Парткод: | 5443 2668 |
| Деталь: | Shaft:Lock |
| Парткод: | B132 2691 |
| Деталь: | Pawl:Lock:Rear |
| Парткод: | B132 2692 |
| Деталь: | SPRING |
| Парткод: | AA06 6372 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2116 |
| Деталь: | Roller:Connecting:Drive |
| Парткод: | B132 2658 |
| Деталь: | Guide Plate:Entrance:Lower Left:Peen |
| Парткод: | B181 2790 |
| Деталь: | EXIT ROLLER SPRING |
| Парткод: | AA06 3433 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA08 0034 |
| Деталь: | Transport Roller:Driven:Duplex |
| Парткод: | B132 2675 |
| Деталь: | Bushing:Registration:Front |
| Парткод: | B132 2724 |
| Деталь: | Spring:Registration:20n |
| Парткод: | AA06 2329 |
| Деталь: | Collar - 8mm |
| Парткод: | 5446 2901 |
| Деталь: | Cover:Harness:Pull Out |
| Парткод: | B132 1232 |
| Деталь: | Bushing:Registration:Rear |
| Парткод: | B132 2725 |
| Деталь: | Gear:50Z |
| Парткод: | AB01 1300 |
| Деталь: | Guide Plate:Open And Close:Middle |
| Парткод: | B181 2641 |
| Деталь: | Cleaning Draive Unit:Charge |
| Парткод: | D014 3553 |
| Деталь: | Shaft:Drive:Cleaner:Charge Corona |
| Парткод: | D014 3558 |
| Деталь: | Gear:20Z |
| Парткод: | D014 3559 |
| Деталь: | Motor:DC5V 0.71W |
| Парткод: | AX04 0167 |
| Деталь: | Housing:Charge Corona |
| Парткод: | D014 3554 |
| Деталь: | Gear:11Z |
| Парткод: | D014 2419 |
| Деталь: | Duct:Joint:PCU:M&K:Assy |
| Парткод: | D014 3670 |
| Деталь: | Harness:T:Sensor:Drawer |
| Парткод: | D014 5272 |
| Деталь: | Connector:1Pole |
| Парткод: | D014 3550 |
| Деталь: | Harness:PCU:Drawer:MCY |
| Парткод: | D014 5271 |
| Деталь: | Screw:PCU |
| Парткод: | B259 1131 |
| Деталь: | Receptacle:Development Unit |
| Парткод: | D014 3261 |
| Деталь: | Harness:Development:BM |
| Парткод: | D014 5340 |
| Деталь: | Harness:Development:CY |
| Парткод: | D014 5342 |
| Деталь: | Duct:Joint:PCU:Color |
| Парткод: | D014 3630 |
| Деталь: | Harness:PCU:Drawer:Black |
| Парткод: | D014 5270 |
| Деталь: | Duct:Connecting:Fusing Unit |
| Парткод: | D014 3601 |
| Деталь: | Bracket:On-Off:Plate |
| Парткод: | B132 1339 |
| Деталь: | DC Motor:On-off:Assy |
| Парткод: | B132 1338 |
| Деталь: | Drive Unit:Transfer Belt |
| Парткод: | D014 1300 |
| Деталь: | Bracket:DC Motor |
| Парткод: | D014 1265 |
| Деталь: | DC Motor:DC24V:6W |
| Парткод: | AX05 0293 |
| Деталь: | DC Motor:DC24V:9W |
| Парткод: | D014 1255 |
| Деталь: | DC Motor:DC24V:21W |
| Парткод: | AX06 0359 |
| Деталь: | Bracket:Drive Unit |
| Парткод: | D014 1270 |
| Деталь: | Pulley:27T |
| Парткод: | D014 1279 |
| Деталь: | Holder:Drive Unit |
| Парткод: | D014 1267 |
| Деталь: | Timing Belt:40DS2M300 |
| Парткод: | AA04 3978 |
| Деталь: | Timing Pulley:23T |
| Парткод: | AB03 0819 |
| Деталь: | Shaft:Drive:Transport Screw |
| Парткод: | D014 1285 |
| Деталь: | Drum Shaft |
| Парткод: | D014 1251 |
| Деталь: | Timing Pulley:37T |
| Парткод: | AB03 0766 |
| Деталь: | Shaft:Drive:Development Unit |
| Парткод: | D014 1280 |
| Деталь: | Bracket:Auxiliary:Drive Unit |
| Парткод: | D014 1275 |
| Деталь: | Gear:60Z/47T |
| Парткод: | D014 1261 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0950 |
| Деталь: | Bracket:Tightener |
| Парткод: | D014 1276 |
| Деталь: | Gear:81Z |
| Парткод: | AB01 0143 |
| Деталь: | Gear:93Z |
| Парткод: | AB01 0142 |
| Деталь: | DC Motor:MM56:DC24V:12W |
| Парткод: | AX06 0360 |
| Деталь: | Development Unit |
| Парткод: | D014 3005 |
| Деталь: | Plate:Filter |
| Парткод: | B065 3108 |
| Деталь: | Filter:Development |
| Парткод: | B247 3340 |
| Деталь: | Cap:Toner Supply:Upper |
| Парткод: | B132 3179 |
| Деталь: | Connector Holder - Density Sensor |
| Парткод: | D014 3130 |
| Деталь: | Developer:Black |
| Парткод: | D014 9640 |
| Деталь: | Developer:Cyan |
| Парткод: | D014 9660 |
| Деталь: | Developer:Magenta |
| Парткод: | D014 9670 |
| Деталь: | Developer:Yellow |
| Парткод: | D014 9680 |
| Деталь: | Bracket:Plate:Joint |
| Парткод: | D014 3136 |
| Деталь: | Plate - Density Sensor |
| Парткод: | D014 3132 |
| Деталь: | Joint Gear - 180Z |
| Парткод: | AB01 1276 |
| Деталь: | Idel Gear - 21Z |
| Парткод: | AB01 1277 |
| Деталь: | Gear - 17Z |
| Парткод: | AB01 1275 |
| Деталь: | Idel Gear - 18Z |
| Парткод: | AB01 1279 |
| Деталь: | OPC Drum |
| Парткод: | D014 9510 |
| Деталь: | Rear Stay - PCU |
| Парткод: | D014 3044 |
| Деталь: | Joint:Drive:Development Unit |
| Парткод: | D014 3135 |
| Деталь: | Front Stay - PCU |
| Парткод: | D014 3043 |
| Деталь: | Adjusting Pin:Magnetic Roller |
| Парткод: | B132 3159 |
| Деталь: | Paper Transport Belt Unit |
| Парткод: | D014 3850 |
| Деталь: | Transport Belt |
| Парткод: | AA04 0033 |
| Деталь: | Transport Roller:Driven |
| Парткод: | AF02 2064 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Transport Roller:Drive |
| Парткод: | B132 3851 |
| Деталь: | Supporting Plate:Vacuum |
| Парткод: | B132 3862 |
| Деталь: | Fan Motor MM60/15mm:24V |
| Парткод: | AX64 0158 |
| Деталь: | Harness:Fan Motor |
| Парткод: | D014 5248 |
| Деталь: | Collection Coil:Toner:Assy |
| Парткод: | B132 6260 |
| Деталь: | Tray:Toner Catchpan:Assy |
| Парткод: | B132 6257 |
| Деталь: | Stay:Pull Out |
| Парткод: | B132 6304 |
| Деталь: | Gear:30T |
| Парткод: | AB01 7338 |
| Деталь: | Timing Belt:S2M208 |
| Парткод: | AA04 3578 |
| Деталь: | Pulley:31T |
| Парткод: | AB03 0275 |
| Деталь: | Stopper:Transfer/Separation Unit |
| Парткод: | B132 6286 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Pulley:40T |
| Парткод: | AB03 0748 |
| Деталь: | Holder:Heater |
| Парткод: | B132 6507 |
| Деталь: | Heat Sink:Heater:Toner |
| Парткод: | B132 6506 |
| Деталь: | Heater:115V:18W:Upper |
| Парткод: | AX40 0176 |
| Деталь: | Heater:240V:18W:Upper |
| Парткод: | AX40 0178 |
| Деталь: | Cover:Heater |
| Парткод: | B181 6502 |
| Деталь: | Seal:Tray:Toner Recycling Unit |
| Парткод: | B132 6328 |
| Деталь: | Stepped Screw - M3x10 |
| Парткод: | AA14 3394 |
| Деталь: | INTERFACE HARNESS |
| Парткод: | B477 5751 |
| Деталь: | Harness:Motor:Exit |
| Парткод: | B652 5422 |
| Деталь: | Harness:Solenoid:Reverse |
| Парткод: | B652 5426 |
| Деталь: | Harness:Paper Size Sensor |
| Парткод: | B652 5406 |
| Деталь: | Harness:Original Sensor |
| Парткод: | B652 5401 |
| Деталь: | Harness:Motor:Pick Up |
| Парткод: | B652 5441 |
| Деталь: | Paper Feed Motor Harness |
| Парткод: | B477 5691 |
| Деталь: | PCB:Main Control:Assy |
| Парткод: | B652 5504 |
| Деталь: | Stepper Motor:Base:Rise:Assy |
| Парткод: | B652 2911 |
| Деталь: | Bracket:Motor:Base:Assy |
| Парткод: | B652 2343 |
| Деталь: | Timing Belt:B40S2M158 |
| Парткод: | B700 4428 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A806 2287 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A806 2285 |
| Деталь: | Spacer - 8x20x1 |
| Парткод: | AA13 2152 |
| Деталь: | Timing Pulley - T30/Z20 S2M/M0.8 |
| Парткод: | A806 2161 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A806 2283 |
| Деталь: | DC Stepper Motor:Exit:2.1W |
| Парткод: | B652 4772 |
| Деталь: | Timing Belt:B40S2M138 |
| Парткод: | B652 4728 |
| Деталь: | Scanning Motor- DC 7.4W |
| Парткод: | B477 3721 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B652 3211 |
| Деталь: | Tension Spring:Tension:Transport |
| Парткод: | AA06 0991 |
| Деталь: | Guide Plate:Stepper Motor |
| Парткод: | B652 3215 |
| Деталь: | Timing Belt:B60S2M280 |
| Парткод: | B652 1721 |
| Деталь: | Timing Belt:B40S2M230 |
| Парткод: | B652 4153 |
| Деталь: | Bracket:Solenoid:Reverse:Upper |
| Парткод: | B652 4223 |
| Деталь: | Damper - Junction Gate Solenoid |
| Парткод: | A697 2102 |
| Деталь: | DC Solenoid:Assy |
| Парткод: | B652 4222 |
| Деталь: | Bracket:Shaft:Scanning:Assy |
| Парткод: | B652 1781 |
| Деталь: | PULLEY |
| Парткод: | B477 3217 |
| Деталь: | Screw:Safety |
| Парткод: | AA14 3791 |
| Деталь: | PULLEY |
| Парткод: | B477 3175 |
| Деталь: | TENSION SPRING |
| Парткод: | B652 3174 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 5215 2621 |
| Деталь: | Belt Tensioner:Assy |
| Парткод: | B652 3231 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Paper Feed Motor - DC 7.4W |
| Парткод: | B477 3711 |
| Деталь: | Paper Feed Motor Stay |
| Парткод: | B477 3115 |
| Деталь: | Paper Feed Motor Bracket |
| Парткод: | B477 3111 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0842 |
| Деталь: | Spacer:Reverse Roller:Rear |
| Парткод: | B652 1633 |
| Деталь: | Gear - 37Z |
| Парткод: | B477 3161 |
| Деталь: | Gear - 31Z |
| Парткод: | B477 3151 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | PULLEY |
| Парткод: | A548 2139 |
| Деталь: | Stopper:Shaft:Separation |
| Парткод: | B477 2244 |
| Деталь: | Gear - 24Z |
| Парткод: | B477 3123 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A859 2230 |
| Деталь: | Shaft:Separation:Drive |
| Парткод: | B477 3124 |
| Деталь: | Feeler - Pick-up Roller Cam |
| Парткод: | A680 2262 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 5053 0447 |
| Деталь: | Pick-up Roller Cam |
| Парткод: | B477 3251 |
| Деталь: | Stepper Motor:MM42:0.95A:9.5V |
| Парткод: | AX04 0139 |
| Деталь: | Gear - 20Z |
| Парткод: | B477 3143 |
| Деталь: | Timing Belt:B40S3M186 |
| Парткод: | B652 1643 |
| Деталь: | Gear - 23Z |
| Парткод: | B477 3141 |
| Деталь: | PULLEY |
| Парткод: | B477 3177 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Timing Belt:B40S2M178 |
| Парткод: | B652 1773 |
| Деталь: | Pulley - 39Z |
| Парткод: | B301 2141 |
| Деталь: | Timing Belt:B60S2M212 |
| Парткод: | B652 1613 |
| Деталь: | PULLEY |
| Парткод: | B477 3145 |
| Деталь: | Paper Feed Drive Bracket |
| Парткод: | B477 3181 |
| Деталь: | PULLEY |
| Парткод: | B477 3171 |
| Деталь: | Timing Belt:B40S2M170 |
| Парткод: | B652 1674 |
| Деталь: | Timing Belt:B40S3M180 |
| Парткод: | B652 1673 |
| Деталь: | PULLEY |
| Парткод: | B477 3173 |
| Деталь: | Damper - Junction Gate Solenoid |
| Парткод: | A697 2102 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 1134 |
| Деталь: | Shaft:Slider |
| Парткод: | B652 1133 |
| Деталь: | Decal:Paper Tray:Display:1 |
| Парткод: | AA00 3211 |
| Деталь: | Cover - Tandem LCT |
| Парткод: | D014 6671 |
| Деталь: | Tandem LCT Unit - Left |
| Парткод: | B234 6616 |
| Деталь: | LEFT SIDE PLATE |
| Парткод: | A294 6645 |
| Деталь: | Bracket:Cover:Tandem LCT:Assy |
| Парткод: | B070 6516 |
| Деталь: | Decal - Paper Set - Left |
| Парткод: | B065 6846 |
| Деталь: | Left Front Fence |
| Парткод: | A294 6643 |
| Деталь: | Tray Bottom Plate:Left Front |
| Парткод: | B132 7540 |
| Деталь: | Tray Bottom Plate:Left Middle:Assy |
| Парткод: | B098 6639 |
| Деталь: | Tray Bottom Plate:Left Rear |
| Парткод: | B132 7541 |
| Деталь: | Decal - Left Paper Set |
| Парткод: | A096 6678 |
| Деталь: | Left Rear Fence |
| Парткод: | A294 6630 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA00 2010 |
| Деталь: | Bracket - Tandem LCT Cover |
| Парткод: | D014 6788 |
| Деталь: | Timing Pulley - 15T |
| Парткод: | AB03 3085 |
| Деталь: | Bracket:Pulley:Driven:Assy |
| Парткод: | B247 6951 |
| Деталь: | Tension Spring:Timing Belt:10n |
| Парткод: | AA06 0987 |
| Деталь: | Shaft:Slider:Back Fence |
| Парткод: | B247 6950 |
| Деталь: | Slider:Back Fence:Left |
| Парткод: | B132 7564 |
| Деталь: | Timing Belt Cover |
| Парткод: | B065 6823 |
| Деталь: | Back Fence:Left |
| Парткод: | B132 7561 |
| Деталь: | Timing Belt S3M 196T |
| Парткод: | AA04 3271 |
| Деталь: | Pulley Bracket |
| Парткод: | B065 6830 |
| Деталь: | Gear - 48T |
| Парткод: | AB01 9475 |
| Деталь: | Timing Pulley - 15T |
| Парткод: | AB03 3084 |
| Деталь: | DC Harness - Left |
| Парткод: | B070 5473 |
| Деталь: | Shaft - Timing Pulley |
| Парткод: | AA14 0686 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 5053 0447 |
| Деталь: | Gear - Z18 |
| Парткод: | AB01 3798 |
| Деталь: | Left DC Motor Bracket |
| Парткод: | B070 6666 |
| Деталь: | DC Motor:Tandem LCT |
| Парткод: | AX04 0145 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0163 |
| Деталь: | Base:Tandem LCT:Left:Assy |
| Парткод: | B247 6970 |
| Деталь: | Sensor bracket |
| Парткод: | B065 6831 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Coupling Lever - Left |
| Парткод: | A248 6615 |
| Деталь: | Grip - Paper Tray Cover |
| Парткод: | B247 6634 |
| Деталь: | Bracket:Sensor:CYK |
| Парткод: | D014 3644 |
| Деталь: | Holder:Electric Potential Sensor |
| Парткод: | D014 3656 |
| Деталь: | Shielding Plate |
| Парткод: | D014 3657 |
| Деталь: | Electric Potential Sensor |
| Парткод: | D014 3655 |
| Деталь: | Bracket:Sensor:M |
| Парткод: | D014 3643 |
| Деталь: | Temperature & Humidity Sensor |
| Парткод: | AW14 0015 |
| Деталь: | DC Solenoid:On-Off |
| Парткод: | D014 3646 |
| Деталь: | Harness:Solenoid |
| Парткод: | D014 5384 |
| Деталь: | Gasket:7x10:50mm |
| Парткод: | D014 2196 |
| Деталь: | Sheet:Heat Pipe:Front |
| Парткод: | D014 6856 |
| Деталь: | Sheet:Heat Pipe:Inner Back |
| Парткод: | D014 6857 |
| Деталь: | Stabilizer |
| Парткод: | AZ50 0075 |
| Деталь: | Bracket:Invertor |
| Парткод: | B132 1851 |
| Деталь: | Bracket:Fan:MM40:Invertor |
| Парткод: | B132 1852 |
| Деталь: | Fan Motor:MM40:15mm |
| Парткод: | AX64 0149 |
| Деталь: | Screw:6x1.7 |
| Парткод: | AA14 3802 |
| Деталь: | Pulley:Tension:Timing Belt:Assy |
| Парткод: | B132 1710 |
| Деталь: | Bracket:Motor |
| Парткод: | B132 1702 |
| Деталь: | PRESSURE SPRING |
| Парткод: | G029 4150 |
| Деталь: | Cushion - Stepper Motor |
| Парткод: | A134 1724 |
| Деталь: | Stepper Motor:DC1.98V 7.13W |
| Парткод: | D014 1703 |
| Деталь: | Cover:Damper |
| Парткод: | B132 1714 |
| Деталь: | Cover:Shaft |
| Парткод: | D014 1716 |
| Деталь: | Drive Were:Scanner |
| Парткод: | B132 1729 |
| Деталь: | Bracket:Tension |
| Парткод: | B132 1724 |
| Деталь: | Bracket:Tension:Fix |
| Парткод: | B132 1725 |
| Деталь: | Spring:Drive Were |
| Парткод: | B132 1723 |
| Деталь: | Timing Belt:100S2M266 |
| Парткод: | AA04 3314 |
| Деталь: | Pulley:40T |
| Парткод: | B132 1720 |
| Деталь: | PULLEY |
| Парткод: | AB03 2070 |
| Деталь: | Screw:Mechanical Drive Section |
| Парткод: | B132 1719 |
| Деталь: | Harness:Siob:VBCU |
| Парткод: | D014 5306 |
| Деталь: | Harness:Siob:Fan:Lamp |
| Парткод: | D014 5302 |
| Деталь: | Harness:SIOB:Original Sensor |
| Парткод: | D014 5300 |
| Деталь: | PCB:SIOB |
| Парткод: | D014 5494 |
| Деталь: | Bracket:Pulley |
| Парткод: | B132 1671 |
| Деталь: | PULLEY |
| Парткод: | AB03 2069 |
| Деталь: | Cover:Polygon Mirror Motor |
| Парткод: | B132 1675 |
| Деталь: | Filter:Scanner |
| Парткод: | D014 1876 |
| Деталь: | Harness:SBU |
| Парткод: | D014 5303 |
| Деталь: | Harness:SBU:Power Source |
| Парткод: | D014 5304 |
| Деталь: | Spring Plate:Cover:SIOB |
| Парткод: | D014 1681 |
| Деталь: | PCB:SCNB |
| Парткод: | D014 5486 |
| Деталь: | Interface Cable:Scanner: Image Processing Unit |
| Парткод: | D014 5305 |
| Деталь: | Gasket:Shading Plate |
| Парткод: | D014 1748 |
| Деталь: | Gasket:Cover:Shaft |
| Парткод: | D014 1747 |
| Деталь: | Bracket:Tension:Inner Back:Peen |
| Парткод: | D014 1722 |
| Деталь: | Gate Pawl:Reverse:Lower:Left |
| Парткод: | B652 4527 |
| Деталь: | Gate Pawl:Reverse:Lower:Right |
| Парткод: | B652 4528 |
| Деталь: | Cushion - Bin Solenoid Lever |
| Парткод: | A458 2251 |
| Деталь: | Bushing:Reverse:Lower:Gate Pawl |
| Парткод: | B652 4520 |
| Деталь: | Roller:Scanning:Exit:Driven |
| Парткод: | B652 4519 |
| Деталь: | Driven Exit Arm |
| Парткод: | B477 2637 |
| Деталь: | Exit Arm Spring |
| Парткод: | B477 4127 |
| Деталь: | Guide Plate:Reverse:Lower |
| Парткод: | B652 4521 |
| Деталь: | Screw:DIA6 |
| Парткод: | AA14 3843 |
| Деталь: | Short Arm Shaft |
| Парткод: | B477 2645 |
| Деталь: | Long Arm Shaft |
| Парткод: | B477 2641 |
| Деталь: | Lever:Reverse:Lower |
| Парткод: | B652 4529 |
| Деталь: | Driven Exit Scanning Roller |
| Парткод: | B477 2636 |
| Деталь: | Arm:Pressure:Reverse:Lower |
| Парткод: | B652 4517 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 4518 |
| Деталь: | TENSION SPRING |
| Парткод: | B652 4530 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B477 2621 |
| Деталь: | Bracket:Reverse:Lower |
| Парткод: | B652 4522 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 5053 0447 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | EXIT ROLLER |
| Парткод: | B652 4726 |
| Деталь: | Guide Plate:Reverse:Lower:Fix |
| Парткод: | B652 4602 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 1853 |
| Деталь: | Bushing- Exit Driven Roller |
| Парткод: | A859 4836 |
| Деталь: | DRIVEN EXIT ROLLER |
| Парткод: | B477 2861 |
| Деталь: | Cover:Exit |
| Парткод: | B652 1852 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Harness:Sensor:Reverse:Lower |
| Парткод: | B652 5456 |
| Деталь: | Cover:Sensor:Reverse:Lower |
| Парткод: | B652 1854 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A859 2230 |
| Деталь: | Timing Pulley:44t |
| Парткод: | B652 4727 |
| Деталь: | Pressure Plate Tape |
| Парткод: | B477 2715 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Guide Roller - B |
| Парткод: | A300 2134 |
| Деталь: | Rail:Left:Assy |
| Парткод: | B132 4835 |
| Деталь: | Rail:Right:Assy |
| Парткод: | B132 4591 |
| Деталь: | Roller - Positioning Guide |
| Парткод: | 6754 2866 |
| Деталь: | Hexagonal Bolt:M12x35 |
| Парткод: | AA14 3798 |
| Деталь: | Heat Sink:Heater:Lower:NA:Assy |
| Парткод: | B140 6225 |
| Деталь: | Heat Sink:Heater:Lower:EU:Assy |
| Парткод: | B140 6226 |
| Деталь: | Cover:Temperature/Humidity Sensor |
| Парткод: | B132 6579 |
| Деталь: | Guide:Tank:Discharge Used Toner |
| Парткод: | B181 6577 |
| Деталь: | Temperature & Humidity Sensor |
| Парткод: | AW14 0015 |
| Деталь: | Caster:1470n |
| Парткод: | AH01 2031 |
| Деталь: | Flanged Hexagonal Head Bolt:Caster |
| Парткод: | AA14 3803 |
| Деталь: | Harness:Duplex:Fan:Middle |
| Парткод: | D014 5266 |
| Деталь: | Fan Motor:MM80 |
| Парткод: | AX64 0163 |
| Деталь: | Bracket:Fan:Duplex |
| Парткод: | B132 1118 |
| Деталь: | Cushion - Motor |
| Парткод: | AA16 1104 |
| Деталь: | PAPER GUIDE SHEET |
| Парткод: | A096 6693 |
| Деталь: | BRACKET |
| Парткод: | B065 1092 |
| Деталь: | Bracket:Holder:Assy |
| Парткод: | B132 4830 |
| Деталь: | Sheet:Duct:Lower |
| Парткод: | A222 1193 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0118 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 5206 2684 |
| Деталь: | Bracket -paper Feed Sensor |
| Парткод: | D014 4258 |
| Деталь: | Guide - Fusing Exit |
| Парткод: | D014 4257 |
| Деталь: | Guide Plate - Fusing Exit |
| Парткод: | D014 4256 |
| Деталь: | Bracket - Cleaning Roller |
| Парткод: | D014 4250 |
| Деталь: | Pickoff Pawl:Pressure Sub-Unit:Sub-Assy |
| Парткод: | D014 4255 |
| Деталь: | Rear Side Plate - Cleaning Roller |
| Парткод: | D014 4254 |
| Деталь: | Spring - Oil Supply Roller |
| Парткод: | AA06 3991 |
| Деталь: | Rear Bushing - Cleaning Roller |
| Парткод: | AE03 1069 |
| Деталь: | Oil Supply Roller |
| Парткод: | AE04 0042 |
| Деталь: | Cleaning Roller:Assy |
| Парткод: | AE04 2080 |
| Деталь: | Front Side Plate - Cleaning Roller |
| Парткод: | D014 4253 |
| Деталь: | Front Bushing - Cleaning Roller |
| Парткод: | AE03 1068 |
| Деталь: | Duplex Turn Roller |
| Парткод: | AF02 1075 |
| Деталь: | Roller:Transport:Driven:Left:Right |
| Парткод: | B247 4812 |
| Деталь: | Roller:Reversal:Drive |
| Парткод: | B247 4813 |
| Деталь: | Roller:Drive:Left |
| Парткод: | B247 4825 |
| Деталь: | Jogger Guide Rod |
| Парткод: | B065 4694 |
| Деталь: | Right Drive Roller |
| Парткод: | AF02 1079 |
| Деталь: | Timing Pulley - 24Z |
| Парткод: | AB03 0583 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Timing Belt:40S2M278G |
| Парткод: | AA04 3310 |
| Деталь: | Timing Belt:40S2M302G |
| Парткод: | AA04 3311 |
| Деталь: | Gear:45Z |
| Парткод: | AB01 1497 |
| Деталь: | PULLEY |
| Парткод: | AB01 7614 |
| Деталь: | Gear:22Z |
| Парткод: | AB01 1498 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Gear - 32Z |
| Парткод: | AB01 1496 |
| Деталь: | Pulley - 29Z |
| Парткод: | AB03 0731 |
| Деталь: | ADF UNIT |
| Парткод: | B132 7453 |
| Деталь: | Cover:Front |
| Парткод: | B652 1902 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Cover:Rear |
| Парткод: | B652 1952 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Stopper:Guide Plate:Pressure Plate |
| Парткод: | B652 4903 |
| Деталь: | Pressure Plate Tape |
| Парткод: | B477 2715 |
| Деталь: | Pressure Plate:Assy |
| Парткод: | B652 4741 |
| Деталь: | Guide Plate:Pressure Plate |
| Парткод: | B652 4902 |
| Деталь: | Magnet Catch - 5n |
| Парткод: | B352 2650 |
| Деталь: | Decal:Misfeed Removal |
| Парткод: | B652 4905 |
| Деталь: | STEPPED SCREW |
| Парткод: | A859 7211 |
| Деталь: | Decal:Misfeed Removal |
| Парткод: | B652 1906 |
| Деталь: | Decal:Misfeed Removal:Exit |
| Парткод: | B652 1905 |
| Деталь: | Carriage:No.2:Assy |
| Парткод: | B132 1801 |
| Деталь: | Spring Plate - 2nd Mirror |
| Парткод: | G404 2810 |
| Деталь: | Mirror:No.2 |
| Парткод: | B132 1818 |
| Деталь: | Mirror:No.3 |
| Парткод: | B132 1819 |
| Деталь: | Holder:Pulley |
| Парткод: | B132 1815 |
| Деталь: | Pulley - High Voltage Supply Cord |
| Парткод: | G570 2834 |
| Деталь: | Original Sensor - 66mm |
| Парткод: | AW01 0133 |
| Деталь: | Original Sensor:H81.5 |
| Парткод: | AW01 0115 |
| Деталь: | Harness:Connecting:Scanner:Lamp |
| Парткод: | B132 5304 |
| Деталь: | Bracket:Original Sensor |
| Парткод: | D014 1861 |
| Деталь: | Carriage:No.1 |
| Парткод: | D014 1751 |
| Деталь: | GRIP |
| Парткод: | G570 2731 |
| Деталь: | Feeler:Home Position Sensor:No.1 |
| Парткод: | B132 1766 |
| Деталь: | Holder:Connector |
| Парткод: | B132 1767 |
| Деталь: | Stay:Wire |
| Парткод: | B132 1758 |
| Деталь: | Xenon Lamp:50000LX |
| Парткод: | AX50 0101 |
| Деталь: | 1st Mirror Holder |
| Парткод: | A193 1767 |
| Деталь: | Mirror:No.1:Assy |
| Парткод: | B132 1757 |
| Деталь: | Anticondensation Heater - 120V 9W |
| Парткод: | AX40 0122 |
| Деталь: | Anticondensation Heater - 230V 10W |
| Парткод: | AX40 0123 |
| Деталь: | Guide:Relay:Paper Feed Unit |
| Парткод: | B132 6758 |
| Деталь: | Sheet:Micro Switch:12mm |
| Парткод: | B132 5999 |
| Деталь: | Bracket:Micro Switch:Paper Bank |
| Парткод: | B132 5971 |
| Деталь: | TORSION SPRING |
| Парткод: | B132 5869 |
| Деталь: | Screw:Micro Switch |
| Парткод: | B132 5868 |
| Деталь: | Transport Unit:Vertical Transport:Assy |
| Парткод: | B132 6771 |
| Деталь: | Spring - 10mm |
| Парткод: | AA06 3487 |
| Деталь: | Cover:Release:Vertical Transport |
| Парткод: | B247 6430 |
| Деталь: | Decal - Grip |
| Парткод: | A029 2984 |
| Деталь: | Lever:Release:Vertical Transport |
| Парткод: | B247 6426 |
| Деталь: | Release Button - Vertical Transport |
| Парткод: | B065 6428 |
| Деталь: | Release Lever - Vertical Transport |
| Парткод: | B065 6427 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3560 |
| Деталь: | Side Plate:Front:Vertical Transport |
| Парткод: | B132 6753 |
| Деталь: | Side Plate:Rear:Vertical Transport |
| Парткод: | B132 6754 |
| Деталь: | Pressure Plate:Transport Roller:Driven:No.1 |
| Парткод: | B132 6752 |
| Деталь: | Transport Pressure Plate |
| Парткод: | B065 6407 |
| Деталь: | Stepped Screw - M5 |
| Парткод: | B247 6982 |
| Деталь: | Vertical Driven Roller |
| Парткод: | AF02 0295 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0241 |
| Деталь: | SPRING |
| Парткод: | AA06 3878 |
| Деталь: | Transport Roller |
| Парткод: | AF02 0562 |
| Деталь: | Gear - 24Z/40Z |
| Парткод: | AB01 7619 |
| Деталь: | Gear - 35Z |
| Парткод: | AB01 1466 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3575 |
| Деталь: | Joint Unit Guide Plate Assy |
| Парткод: | B140 6472 |
| Деталь: | Stepper Motor:Paper Feed Unit:Assy |
| Парткод: | B132 6655 |
| Деталь: | Harness - Joint Unit |
| Парткод: | B132 7583 |
| Деталь: | Gear:32Z |
| Парткод: | AB01 1301 |
| Деталь: | Guard:Pull Out |
| Парткод: | B132 1192 |
| Деталь: | Guide Plate:Paper Bank:Assy |
| Парткод: | B132 2767 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0203 |
| Деталь: | Transport Roller:Driven |
| Парткод: | B132 2639 |
| Деталь: | Driven Roller Spring |
| Парткод: | AA06 3254 |
| Деталь: | Guide Plate:Connecting: Right Upper:Adhesion |
| Парткод: | D014 2636 |
| Деталь: | HARNESS:SENSOR |
| Парткод: | D014 5247 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Bracket:Sensor:Connecting |
| Парткод: | B181 2773 |
| Деталь: | DC Solenoid:24V:16.5W:Assy |
| Парткод: | B132 2594 |
| Деталь: | Arm:Guide |
| Парткод: | B132 2649 |
| Деталь: | Arm:Perpendicular |
| Парткод: | B132 2650 |
| Деталь: | Support Stay:Solenoid |
| Парткод: | B132 2753 |
| Деталь: | Bracket:Solenoid |
| Парткод: | B132 2661 |
| Деталь: | Rail:Solenoid:Release |
| Парткод: | B132 2667 |
| Деталь: | Cover:Motor:Registration |
| Парткод: | B132 2723 |
| Деталь: | Snap Ring |
| Парткод: | 5206 2686 |
| Деталь: | Bracket:Tightener |
| Парткод: | B132 2720 |
| Деталь: | TENSION SPRING |
| Парткод: | B132 2710 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B132 2711 |
| Деталь: | Timing Belt:60S2M138 |
| Парткод: | AA04 3312 |
| Деталь: | Stepper Motor:Registration:Assy |
| Парткод: | B132 2722 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Bracket:Photointerruptor |
| Парткод: | B132 1233 |
| Деталь: | Guide:Duplex:Upper Right |
| Парткод: | B132 4868 |
| Деталь: | Shield:Joint:PCU |
| Парткод: | B132 6578 |
| Деталь: | Case:Toner Outlet Sub-unit:Cover |
| Парткод: | B132 6519 |
| Деталь: | Case:Toner Outlet Sub-unit |
| Парткод: | B132 6518 |
| Деталь: | Toner Catchpan:Tank:Entrance |
| Парткод: | B132 6539 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Transport Screw:Upper:Assy |
| Парткод: | B132 6520 |
| Деталь: | Harness:Bank |
| Парткод: | D014 5393 |
| Деталь: | Photointerruptor:Feeler:Square |
| Парткод: | AW02 0147 |
| Деталь: | Base:Toner Outlet Sub-unit:Assy |
| Парткод: | B132 6512 |
| Деталь: | Bracket:Toner Outlet Sub-unit:Drive |
| Парткод: | B132 6514 |
| Деталь: | TENSION SPRING |
| Парткод: | B132 6542 |
| Деталь: | Gear:31/44Z |
| Парткод: | AB01 1029 |
| Деталь: | Shaft:Toner Outlet Sub-unit |
| Парткод: | B132 6527 |
| Деталь: | Shaft:Drive:Long:Assy |
| Парткод: | B132 6548 |
| Деталь: | Gear:18Z |
| Парткод: | AB01 3299 |
| Деталь: | Brushless MotorDC24V 2.4W |
| Парткод: | AX06 0302 |
| Деталь: | Cover:DC Motor |
| Парткод: | B132 6537 |
| Деталь: | Gear:14/30Z |
| Парткод: | AB01 1248 |
| Деталь: | Gear:32Z |
| Парткод: | AB01 1247 |
| Деталь: | Bushing:Transport Screw |
| Парткод: | B132 6536 |
| Деталь: | Toner Collection Gear |
| Парткод: | B065 3587 |
| Деталь: | Spacer - M6 |
| Парткод: | AA13 2208 |
| Деталь: | SPRING |
| Парткод: | B065 3561 |
| Деталь: | Guide:Spring:Discharge Used Toner |
| Парткод: | B132 6526 |
| Деталь: | Harness:DC PSU |
| Парткод: | D014 5210 |
| Деталь: | POWER SUPPLY UNIT |
| Парткод: | AZ26 0005 |
| Деталь: | Bracket:Power Supply Unit:Fix:Left |
| Парткод: | B132 5978 |
| Деталь: | Stopper:Power Supply Cord |
| Парткод: | B132 5995 |
| Деталь: | Power Supply Cord - NA |
| Парткод: | D014 5361 |
| Деталь: | Power Supply Cord - 230V |
| Парткод: | D014 5362 |
| Деталь: | Power Supply Cord - 230V |
| Парткод: | D014 5364 |
| Деталь: | Bracket:Power Supply Cord:EXP |
| Парткод: | B132 5994 |
| Деталь: | Harness:AC:Main:Switch |
| Парткод: | D014 5200 |
| Деталь: | Harness:Bank:Dehumidifier |
| Парткод: | D014 5392 |
| Деталь: | Harness:PSU:Short Circuit |
| Парткод: | D014 5202 |
| Деталь: | AC Drive Board:100V |
| Парткод: | D014 5530 |
| Деталь: | AC Drive Board - 230V |
| Парткод: | D014 5532 |
| Деталь: | Bracket:Power Pack:Fix:Lower |
| Парткод: | B132 5981 |
| Деталь: | Harness:Connecting:AC Drive Board |
| Парткод: | D014 5380 |
| Деталь: | Bracket:Leak Breaker |
| Парткод: | B132 5985 |
| Деталь: | Bracket:Ac Drive Board |
| Парткод: | D014 5981 |
| Деталь: | Bracket:Power Pack:Upper |
| Парткод: | D014 5986 |
| Деталь: | Bracket:Fix:C/T Box:Lower |
| Парткод: | B132 5911 |
| Деталь: | Bracket:C/T Box:Lower |
| Парткод: | D014 5869 |
| Деталь: | Shaft:Cleaner |
| Парткод: | AA14 3789 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | B301 1286 |
| Деталь: | Spacer - M6.5x1 |
| Парткод: | A418 1158 |
| Деталь: | Compression Spring:Paper Feed:Joint |
| Парткод: | AA06 3435 |
| Деталь: | SPACER |
| Парткод: | AA13 2013 |
| Деталь: | Guide Plate Cushion |
| Парткод: | A806 1163 |
| Деталь: | Front Entrance Guide |
| Парткод: | B477 2172 |
| Деталь: | Feed-in Unit Stopper |
| Парткод: | A680 1621 |
| Деталь: | Bushing - 8mm |
| Парткод: | A628 1225 |
| Деталь: | Feed Belt Drive Roller |
| Парткод: | A806 1293 |
| Деталь: | Separation Shaft |
| Парткод: | B477 2191 |
| Деталь: | Feed Belt |
| Парткод: | A806 1295 |
| Деталь: | SPRING BELT GUIDE ROLLER |
| Парткод: | A806 4261 |
| Деталь: | Feed Belt Driven Roller |
| Парткод: | A806 1294 |
| Деталь: | Transport Belt Roller Shaft |
| Парткод: | A806 1298 |
| Деталь: | Feed Belt Bracket |
| Парткод: | A806 1292 |
| Деталь: | Rear Entrance Guide |
| Парткод: | B477 2182 |
| Деталь: | Pick-up Roller Lever |
| Парткод: | B477 2231 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 5053 0447 |
| Деталь: | Pickup Roller:Coupling |
| Парткод: | B477 2227 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | B477 2225 |
| Деталь: | Spacer - 6x20x1 |
| Парткод: | AA13 2171 |
| Деталь: | Timing Belt:B40S2M142 |
| Парткод: | B652 2213 |
| Деталь: | Timing Pulley:21T |
| Парткод: | B652 2212 |
| Деталь: | Guide:Paper Feed Belt:Front |
| Парткод: | B652 2215 |
| Деталь: | Pick-up Roller Bracket |
| Парткод: | B477 2222 |
| Деталь: | Timing Pulley - T19/Z23 S2M/M0.6 |
| Парткод: | A806 2151 |
| Деталь: | Gear - Z18 |
| Парткод: | A806 2271 |
| Деталь: | Paper Exit Unit |
| Парткод: | D014 7001 |
| Деталь: | Grip:Guide Plate:Upper |
| Парткод: | B132 7056 |
| Деталь: | Pawl:Guide Plate:Fix |
| Парткод: | B132 7044 |
| Деталь: | Shaft:Release:Guide Plate:Upper |
| Парткод: | B132 7052 |
| Деталь: | Spring:Tightener |
| Парткод: | AA06 3908 |
| Деталь: | Stopper:Pipe |
| Парткод: | B132 7105 |
| Деталь: | Guide Plate:Transport:Upper:Left |
| Парткод: | B132 7016 |
| Деталь: | Spring Plate:Upper:Right |
| Парткод: | B132 7013 |
| Деталь: | Roller:MM14 |
| Парткод: | B132 7033 |
| Деталь: | Bushing:DIA6 |
| Парткод: | AA08 0213 |
| Деталь: | Guide Plate:Right |
| Парткод: | D014 7010 |
| Деталь: | Sound Proofing Material |
| Парткод: | B132 7124 |
| Деталь: | Guide Plate:Entrance:Upper |
| Парткод: | B132 7129 |
| Деталь: | Guide:Entrance:Right Front |
| Парткод: | B132 7164 |
| Деталь: | Decura:Heat Pipe:DIA15 |
| Парткод: | B132 7005 |
| Деталь: | Bracket:Positioning Plate:Rear |
| Парткод: | B132 7133 |
| Деталь: | Bushing - MM5 |
| Парткод: | AA08 0240 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3906 |
| Деталь: | Supporting Plate:Pull Out:Front |
| Парткод: | B132 1159 |
| Деталь: | Shaft:Knob |
| Парткод: | B181 7037 |
| Деталь: | Gear:28Z |
| Парткод: | B132 7002 |
| Деталь: | Bracket:Lever |
| Парткод: | B181 7007 |
| Деталь: | Holder:Bearing:Front |
| Парткод: | B132 7011 |
| Деталь: | Bracket:Bearing:Front |
| Парткод: | B132 7039 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Knob:Front |
| Парткод: | B132 7008 |
| Деталь: | Decal:LED:E1 |
| Парткод: | B132 7130 |
| Деталь: | Decal:LED:D1 |
| Парткод: | D014 7131 |
| Деталь: | Knob Joint |
| Парткод: | A166 4290 |
| Деталь: | Knob:Fusing |
| Парткод: | AG05 1147 |
| Деталь: | Inner Cover:Left |
| Парткод: | D014 1182 |
| Деталь: | Lever:Release |
| Парткод: | B132 2716 |
| Деталь: | Registration Roller Knob |
| Парткод: | A060 2512 |
| Деталь: | Bracket:LED:Left |
| Парткод: | B132 7166 |
| Деталь: | Fan Motor:Unit:DC24V 2.4W |
| Парткод: | B132 6940 |
| Деталь: | Harness:Front:Fan |
| Парткод: | D014 5277 |
| Деталь: | Decal:Lever:B4 |
| Парткод: | B132 2709 |
| Деталь: | Lever:Pull Out:Printing |
| Парткод: | B132 1184 |
| Деталь: | Inner Cover:Middle |
| Парткод: | D014 1200 |
| Деталь: | Decal:Caution:Pull Out |
| Парткод: | B132 1238 |
| Деталь: | Inner Cover:Pull Out:Right |
| Парткод: | B132 1189 |
| Деталь: | Decal:Caution:Pull Out:Inner Back |
| Парткод: | D014 1570 |
| Деталь: | Paper Feed Unit:Paper Bank |
| Парткод: | B132 6621 |
| Деталь: | Transport Roller |
| Парткод: | AF02 2149 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0327 |
| Деталь: | Driven Shaft |
| Парткод: | AA14 0829 |
| Деталь: | Transport Roller Lever |
| Парткод: | B065 6453 |
| Деталь: | Screw - Scale |
| Парткод: | AA14 3812 |
| Деталь: | Driven Release Lever |
| Парткод: | B065 6454 |
| Деталь: | Driven Pressure Lever |
| Парткод: | B065 6455 |
| Деталь: | Front Side Plate - Paper Feed |
| Парткод: | B065 6336 |
| Деталь: | Support Guide Plate |
| Парткод: | B065 6371 |
| Деталь: | Relay Shaft |
| Парткод: | B065 6317 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1469 |
| Деталь: | Rear Side Plate - Paper Feed |
| Парткод: | B065 6330 |
| Деталь: | Gear - 18Z |
| Парткод: | AB01 1470 |
| Деталь: | Tray Link Guide |
| Парткод: | B065 6452 |
| Деталь: | Paper Tray Link |
| Парткод: | B065 6346 |
| Деталь: | Arm Screw |
| Парткод: | 5894 2540 |
| Деталь: | SPRING |
| Парткод: | AA06 0900 |
| Деталь: | Pulley:Idler:30t/24z |
| Парткод: | AB01 7690 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3575 |
| Деталь: | Vertical Transport Link |
| Парткод: | B065 6456 |
| Деталь: | SPRING |
| Парткод: | AA06 0901 |
| Деталь: | Ground Plate:Stepper Motor:Paper Feed Unit |
| Парткод: | B140 6378 |
| Деталь: | Stepper Motor:Paper Feed Unit:Assy |
| Парткод: | B132 6655 |
| Деталь: | MOTOR BRACKET |
| Парткод: | B065 6394 |
| Деталь: | SPRING |
| Парткод: | AA06 0904 |
| Деталь: | Motor Base |
| Парткод: | B065 6415 |
| Деталь: | Pulley - 20T |
| Парткод: | AB03 0733 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3576 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Paper Feed Roller:Separate |
| Парткод: | AF03 2080 |
| Деталь: | Torque Limiter - 53mnxm |
| Парткод: | A294 6700 |
| Деталь: | Reverse Driven Shaft |
| Парткод: | B065 6307 |
| Деталь: | Gear:Reverse |
| Парткод: | AB01 1591 |
| Деталь: | PCB:DRB |
| Парткод: | D014 5430 |
| Деталь: | Harness:Manual Feed:Stepper Motor |
| Парткод: | D014 5218 |
| Деталь: | Harness:Large Capacity Tray:DRB |
| Парткод: | D014 5216 |
| Деталь: | Harness:DRB:Safety Switch |
| Парткод: | D014 5383 |
| Деталь: | Bracket - DRV |
| Парткод: | D014 5864 |
| Деталь: | PCB:DTMB |
| Парткод: | D014 5425 |
| Деталь: | Harness:Drum:Motor:KMCY |
| Парткод: | D014 5267 |
| Деталь: | Harness:TMB |
| Парткод: | D014 5219 |
| Деталь: | DC Harness - Bank Front |
| Парткод: | D014 5395 |
| Деталь: | Paper Feed Board |
| Парткод: | D014 5465 |
| Деталь: | Power Pack:C |
| Парткод: | AZ32 0168 |
| Деталь: | Harness:High Voltage Supply Cord |
| Парткод: | D014 5350 |
| Деталь: | Bracket - Power Pack |
| Парткод: | D014 5985 |
| Деталь: | Bracket:Finisher |
| Парткод: | D014 5865 |
| Деталь: | Fan Motor:Upper:DC24V 2.4W |
| Парткод: | B132 6954 |
| Деталь: | Bracket:Duplex:Exhaust:Front |
| Парткод: | B132 6950 |
| Деталь: | Fan Motor:Lower:Unit:DC24V 2.64W |
| Парткод: | B132 6951 |
| Деталь: | Cover:Filter:Color |
| Парткод: | D014 3595 |
| Деталь: | Cover:Filter:Black |
| Парткод: | D014 3592 |
| Деталь: | Bracket:Stay:Sirocco |
| Парткод: | D014 3588 |
| Деталь: | Lever:Cover:Filter |
| Парткод: | D014 3589 |
| Деталь: | Spring Plate:Cover:Filter |
| Парткод: | D014 3591 |
| Деталь: | Cover:Duct:Exhaust |
| Парткод: | D014 3584 |
| Деталь: | Ozone Filter:Black |
| Парткод: | D014 3585 |
| Деталь: | DUST FILTER |
| Парткод: | D014 3586 |
| Деталь: | OZONE FILTER |
| Парткод: | B132 2436 |
| Деталь: | DUST FILTER |
| Парткод: | B132 2435 |
| Деталь: | Seal:Duct:Exhaust |
| Парткод: | D014 3590 |
| Деталь: | Duct:Exhaust:PCU |
| Парткод: | D014 3583 |
| Деталь: | Bracket:LCT |
| Парткод: | B132 5866 |
| Деталь: | Harness:Sirocco Fan Motor |
| Парткод: | D014 5385 |
| Деталь: | Fan Motor:Sirocco |
| Парткод: | AX65 0041 |
| Деталь: | Bracket:Duct:Exhaust |
| Парткод: | D014 3587 |
| Деталь: | Sirocco Fan Motor:DC24V 7.92W |
| Парткод: | AX65 0036 |
| Деталь: | Spring Plate:Duct:Exhaust |
| Парткод: | D014 3598 |
| Деталь: | Decal - Cover |
| Парткод: | B065 4480 |
| Деталь: | Cover:Left Middle |
| Парткод: | B132 1506 |
| Деталь: | Cover:Left Lower |
| Парткод: | D014 1509 |
| Деталь: | Waste Toner Bottle |
| Парткод: | B132 6609 |
| Деталь: | Rivet - M6 |
| Парткод: | B039 1367 |
| Деталь: | Cover:Ozone Filter |
| Парткод: | B132 1516 |
| Деталь: | Cover:Rear Middle |
| Парткод: | D014 1507 |
| Деталь: | Screw:M4:Exterior |
| Парткод: | AA14 3801 |
| Деталь: | Cover:Rear Upper |
| Парткод: | B132 1504 |
| Деталь: | Cover:Right Lower |
| Парткод: | B132 1508 |
| Деталь: | Connector cap |
| Парткод: | B065 1341 |
| Деталь: | Cover:Rear Lower |
| Парткод: | D014 1510 |
| Деталь: | Cover:Right Middle |
| Парткод: | D014 1505 |
| Деталь: | G4 Cap |
| Парткод: | B065 1344 |
| Деталь: | LCT Cover |
| Парткод: | B065 1303 |
| Деталь: | Seal:Cover:Right Middle |
| Парткод: | D014 6982 |
| Деталь: | Cover:Cable:Ac Power Supply |
| Парткод: | D014 1512 |
| Деталь: | Cover:Filter:Rear Lower |
| Парткод: | D014 1511 |
| Деталь: | Bracket:Duct:Main:Rear |
| Парткод: | D014 6986 |
| Деталь: | Shield:Duct:Main:Rear |
| Парткод: | D014 6985 |
| Деталь: | Duct:Main:Rear |
| Парткод: | D014 6977 |
| Деталь: | Nylon Clamp |
| Парткод: | A193 1384 |
| Деталь: | DUST FILTER |
| Парткод: | D014 6978 |
| Деталь: | Shield:Duct:Main:Rear |
| Парткод: | D014 6984 |
| Деталь: | Seal:Cover:Rear Middle |
| Парткод: | D014 1500 |
| Деталь: | Decal:Vermont:2 |
| Парткод: | B198 6407 |
| Деталь: | Fusing Unit:C2ANA:Assy |
| Парткод: | D014 4018 |
| Деталь: | Fusing Unit:C2EU:Assy |
| Парткод: | D014 4028 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 5206 2684 |
| Деталь: | Fusing Unit Cover |
| Парткод: | D014 4125 |
| Деталь: | Stopper - Thermostat |
| Парткод: | D014 4190 |
| Деталь: | Stopper Pad - Thermostat |
| Парткод: | D014 4191 |
| Деталь: | Thermostat:Heat Roller:Welding |
| Парткод: | D014 4175 |
| Деталь: | Housing:Thermostat:Press Fit |
| Парткод: | D014 4235 |
| Деталь: | Supporting Plate:Positioning: Fusing Unit:Rear |
| Парткод: | D014 4161 |
| Деталь: | Housing:Thermostat |
| Парткод: | B132 4148 |
| Деталь: | Heater - 117V 400W |
| Парткод: | AX43 0186 |
| Деталь: | Heater - 227V 400W |
| Парткод: | AX43 0190 |
| Деталь: | Front Heater Holder - Pressure |
| Парткод: | D014 4236 |
| Деталь: | Rear Heater Holder - Pressure |
| Парткод: | D014 4237 |
| Деталь: | Heater - 117V 700W |
| Парткод: | AX44 0269 |
| Деталь: | Heater - 227V 700W |
| Парткод: | AX44 0271 |
| Деталь: | Heater - 117V 250W |
| Парткод: | AX43 0188 |
| Деталь: | Heater - 227V 600W |
| Парткод: | AX44 0267 |
| Деталь: | Front Heater Holder - Heat Roller |
| Парткод: | D014 4136 |
| Деталь: | Rear Heater Holder - Heat Roller |
| Парткод: | D014 4138 |
| Деталь: | Supporting Plate:Positioning: FusingUnit:Front |
| Парткод: | D014 4164 |
| Деталь: | Front Stay - Fusing Unit |
| Парткод: | D014 4093 |
| Деталь: | Knob Screw - 4m |
| Парткод: | B051 4103 |
| Деталь: | Thermostat Terminal |
| Парткод: | B065 4121 |
| Деталь: | AC Harness - Thermostat |
| Парткод: | D014 4298 |
| Деталь: | Entrance Guide Plate - Lower |
| Парткод: | D014 4234 |
| Деталь: | Bracket - Thermistor:Pressure |
| Парткод: | D014 4240 |
| Деталь: | THERMISTOR |
| Парткод: | AW10 0110 |
| Деталь: | Housing - Temperature Sensor |
| Парткод: | D014 4247 |
| Деталь: | Bracket - Heat Roller Thermistor |
| Парткод: | D014 4238 |
| Деталь: | Temperature Sensor:Upper |
| Парткод: | AW10 0114 |
| Деталь: | Thermostat:150C:250V/17A |
| Парткод: | AW11 0044 |
| Деталь: | Thermostat:149C:250V/17A |
| Парткод: | AW11 0045 |
| Деталь: | Spacer:Min |
| Парткод: | D014 4343 |
| Деталь: | Spacer:Max |
| Парткод: | D014 4342 |
| Деталь: | Slide Rail:Toner Supply:Assy |
| Парткод: | AA07 0064 |
| Деталь: | Upper Sheet - Stay Left |
| Парткод: | D014 6898 |
| Деталь: | Stay:Intermediate Transfer:Left |
| Парткод: | D014 1003 |
| Деталь: | Lower Sheet - Stay Left |
| Парткод: | D014 6899 |
| Деталь: | Duct:Imaging Unit:Exhaust:Assy |
| Парткод: | B132 6958 |
| Деталь: | Duct:Imaging Unit:Sub-assy |
| Парткод: | B132 6978 |
| Деталь: | Duct:Imaging Unit:1st:Assy |
| Парткод: | B132 6971 |
| Деталь: | Duct:Imaging Unit:Exhaust:Assy |
| Парткод: | B132 6965 |
| Деталь: | Cover:Duct:Imaging Unit:Assy |
| Парткод: | B132 6980 |
| Деталь: | Duct:Imaging Unit:23st:Assy |
| Парткод: | B132 6973 |
| Деталь: | Duct:Imaging Unit:4st:Assy |
| Парткод: | B132 6975 |
| Деталь: | Duct:Humidity Control:Assy |
| Парткод: | B132 2470 |
| Деталь: | Bracket:Exhaust:Harness |
| Парткод: | B132 6867 |
| Деталь: | Bracket:Hinge:Door |
| Парткод: | D014 1463 |
| Деталь: | Spring:Hinge:Upper |
| Парткод: | B132 1465 |
| Деталь: | Hinge Shaft |
| Парткод: | B132 1463 |
| Деталь: | Heat Pipe |
| Парткод: | D014 6882 |
| Деталь: | Sheet - Shielding Plate |
| Парткод: | D014 6891 |
| Деталь: | Screw:Safety |
| Парткод: | AA14 3791 |
| Деталь: | Duct:Exit:Upper |
| Парткод: | B132 6912 |
| Деталь: | Duct:Fusing:Exit:Upper |
| Парткод: | D014 6893 |
| Деталь: | Duct:Fusing:Exit:Upper:Left |
| Парткод: | D014 6894 |
| Деталь: | Duct:Exit:Upper:Left:Assy |
| Парткод: | B132 6908 |
| Деталь: | Decal - Y Toner Supply |
| Парткод: | GA00 3016 |
| Деталь: | Decal - C Toner Supply |
| Парткод: | GA00 3018 |
| Деталь: | Decal - M Toner Supply |
| Парткод: | GA00 3017 |
| Деталь: | Decal - K Toner Supply |
| Парткод: | GA00 3019 |
| Деталь: | Heat Insulation:Heat Pipe:Panel |
| Парткод: | D014 6892 |
| Деталь: | Stepped Screw - M3x26.5 |
| Парткод: | A555 1671 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B132 6550 |
| Деталь: | Bracket:Used Toner Sensor:Install |
| Парткод: | B132 6547 |
| Деталь: | Oil End Sensor |
| Парткод: | AW02 0164 |
| Деталь: | Harness:Bank |
| Парткод: | D014 5394 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B132 6566 |
| Деталь: | Gear - 30Z |
| Парткод: | AB01 3467 |
| Деталь: | Bracket:Used Toner Sensor |
| Парткод: | D014 6552 |
| Деталь: | Bracket:Used Toner Sensor:DC Motor |
| Парткод: | D014 6532 |
| Деталь: | Gear:17/51Z |
| Парткод: | AB01 7000 |
| Деталь: | Shaft:Idler:DC Motor |
| Парткод: | D014 6533 |
| Деталь: | DC Motor:Agitate:Assy |
| Парткод: | B132 6511 |
| Деталь: | DC Motor:Rise:Paper Tray |
| Парткод: | AX04 0144 |
| Деталь: | Bracket:Positioning:Paper Tray:Assy |
| Парткод: | B247 6174 |
| Деталь: | Paper Tray Stopper |
| Парткод: | B065 6172 |
| Деталь: | Bracket:Paper Size Sensor:No.1 |
| Парткод: | B132 6737 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0010 |
| Деталь: | Harness:Bank:Tray:Paper Size Sensor |
| Парткод: | D014 5397 |
| Деталь: | Bracket:Power Supply Unit:Right |
| Парткод: | B132 5977 |
| Деталь: | Bracket:Earth:Power Supply Unit:Rear:Peen |
| Парткод: | B132 5827 |
| Деталь: | Bracket:Power Supply Unit:Right:EXP |
| Парткод: | B132 5997 |
| Деталь: | TONER SUPPLY UNIT |
| Парткод: | D014 3300 |
| Деталь: | STAY |
| Парткод: | B132 3428 |
| Деталь: | Spring Plate:Stand |
| Парткод: | B132 3240 |
| Деталь: | Lever:Stand |
| Парткод: | B132 3239 |
| Деталь: | Shaft:Lever:Stand |
| Парткод: | B132 3216 |
| Деталь: | Spring Plate:Lever:Stand |
| Парткод: | B132 3242 |
| Деталь: | Guide Plate:Lever:Stand |
| Парткод: | B132 3241 |
| Деталь: | Inner Cover:Left |
| Парткод: | B132 3236 |
| Деталь: | Stand:Left |
| Парткод: | B132 3237 |
| Деталь: | Guide:Stand |
| Парткод: | B132 3238 |
| Деталь: | Guide:Arm:Stopper:Holder |
| Парткод: | B132 3323 |
| Деталь: | Arm:Stopper:Holder:Color |
| Парткод: | B132 3322 |
| Деталь: | Bracket:Stopper:Holder:Left:Assy |
| Парткод: | B132 3316 |
| Деталь: | Bracket:Stopper:Holder:Right:Assy |
| Парткод: | B132 3314 |
| Деталь: | Decal:Lever:Toner Supply:M |
| Парткод: | B132 3331 |
| Деталь: | Decal:Lever:Toner Supply:C |
| Парткод: | B132 3332 |
| Деталь: | Decal:Lever:Toner Supply:Y |
| Парткод: | B132 3333 |
| Деталь: | Toner Cartridge Unit:Color |
| Парткод: | D014 3341 |
| Деталь: | Cover:Black |
| Парткод: | B132 3232 |
| Деталь: | Inner Cover:Right |
| Парткод: | B132 3235 |
| Деталь: | Cover:Lower:Holder:Y |
| Парткод: | D014 3354 |
| Деталь: | Cover:Lower:Holder:M |
| Парткод: | D014 3352 |
| Деталь: | Cover:Lower:Holder:C |
| Парткод: | D014 3353 |
| Деталь: | Cover:Color |
| Парткод: | B132 3233 |
| Деталь: | Decal:Cover:Toner Supply:M |
| Парткод: | B132 3248 |
| Деталь: | Decal:Cover:Toner Supply:C |
| Парткод: | B132 3249 |
| Деталь: | Decal:Cover:Toner Supply:Y |
| Парткод: | B132 3250 |
| Деталь: | Arm:Stopper:Holder:Black |
| Парткод: | B132 3321 |
| Деталь: | Decal:Lever:Toner Supply:K |
| Парткод: | B132 3330 |
| Деталь: | Toner Cartridge Unit:Black |
| Парткод: | D014 3340 |
| Деталь: | Cover:Lower:Holder:Bk |
| Парткод: | D014 3351 |
| Деталь: | SHEET |
| Парткод: | B132 3245 |
| Деталь: | Decal:Cover:Toner Supply:Black |
| Парткод: | B132 3247 |
| Деталь: | Harness:ID |
| Парткод: | D014 5252 |
| Деталь: | Harness:ID:Black |
| Парткод: | D014 5256 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 5206 2684 |
| Деталь: | Guide Plate:Lower:Pull Out |
| Парткод: | B652 2152 |
| Деталь: | Decal:Guide Plate:Reverse:Exit |
| Парткод: | B652 4119 |
| Деталь: | Guide Plate:Reverse:Exit:Upper |
| Парткод: | B652 4114 |
| Деталь: | Guide:Reverse:Exit |
| Парткод: | B652 4116 |
| Деталь: | Guide:Reverse:Exit:Middle |
| Парткод: | B652 4117 |
| Деталь: | Guide Plate:Reverse:Middle:Upper |
| Парткод: | B652 4115 |
| Деталь: | Guide Plate:Reverse:Entrance |
| Парткод: | B652 4103 |
| Деталь: | Reverse Roller:Exit:Drive |
| Парткод: | B652 4152 |
| Деталь: | EXIT ROLLER |
| Парткод: | B652 4726 |
| Деталь: | Paper Feed Sensor Bracket |
| Парткод: | B477 2495 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Harness:Sensor:Exit |
| Парткод: | B652 5461 |
| Деталь: | Guide:Scanning:Exit:Long |
| Парткод: | B652 4506 |
| Деталь: | Guide:Scanning:Exit:Short |
| Парткод: | B652 4507 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | Guide:Scanning:Exit:Exit |
| Парткод: | B652 4501 |
| Деталь: | Discharge Brush:Exit:L37 |
| Парткод: | B652 4503 |
| Деталь: | Discharge Brush:Exit:L16 |
| Парткод: | B652 4504 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 5053 0447 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A859 2230 |
| Деталь: | Timing Pulley:44t |
| Парткод: | B652 4727 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Timing Pulley - T28 S2M |
| Парткод: | A806 2111 |
| Деталь: | PIN |
| Парткод: | C105 1866 |
| Деталь: | Guide Bracket |
| Парткод: | B477 2145 |
| Деталь: | Entrance Scanning Guide |
| Парткод: | B477 2581 |
| Деталь: | SPRING |
| Парткод: | B477 4115 |
| Деталь: | Driven Entrance Scanning Roller |
| Парткод: | B477 2577 |
| Деталь: | Bushing- 4x8x4.5mm |
| Парткод: | 5324 1658 |
| Деталь: | SPACER |
| Парткод: | A374 2181 |
| Деталь: | Entrance Scanning Roller Shaft |
| Парткод: | B477 2575 |
| Деталь: | Arm:Roller:Scanning:Entrance |
| Парткод: | B477 2574 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | Entrance Scanning Base |
| Парткод: | B477 2561 |
| Деталь: | Timing Pulley - T28 S2M |
| Парткод: | A806 2111 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Harness:Registration Sensor |
| Парткод: | B652 5431 |
| Деталь: | Registration Sensor Bracket |
| Парткод: | B477 2665 |
| Деталь: | Guide Plate:Entrance:Upper:Assy |
| Парткод: | B652 3251 |
| Деталь: | Discharge Brush |
| Парткод: | A859 3225 |
| Деталь: | Drive Relay Roller |
| Парткод: | B477 2121 |
| Деталь: | Roller:Scanning:Entrance:Drive |
| Парткод: | B652 2411 |
| Деталь: | Roller:Pull Out:Drive |
| Парткод: | B652 2112 |
| Деталь: | Roller:Scanning:Exit:Drive |
| Парткод: | B652 2421 |
| Деталь: | Timing Belt:B80S3M417 |
| Парткод: | B652 1783 |
| Деталь: | Timing Belt:B60S2M172 |
| Парткод: | B652 3135 |
| Деталь: | Bracket:Link:Cover:Paper Feed:Peen |
| Парткод: | B652 1817 |
| Деталь: | Bushing - 16x18x5 |
| Парткод: | AA08 2141 |
| Деталь: | Screw:Safety |
| Парткод: | AA14 3791 |
| Деталь: | Timing Belt:B40S2M230 |
| Парткод: | B652 4153 |
| Деталь: | Discharge Brush:Heat Roller:Upper |
| Парткод: | D014 4353 |
| Деталь: | Spacer:Housing:Thermostat:Front |
| Парткод: | D014 4309 |
| Деталь: | Bracket - Hot Roller Thermistor |
| Парткод: | D014 4239 |
| Деталь: | Stay - Upper |
| Парткод: | D014 4103 |
| Деталь: | Entrance Guide Plate - Upper |
| Парткод: | D014 4147 |
| Деталь: | Rear Stay - Fusing Unit |
| Парткод: | D014 4095 |
| Деталь: | Gear - 30Z/23Z |
| Парткод: | AB01 4294 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 4295 |
| Деталь: | Rear Positioning Plate - Stripper |
| Парткод: | D014 4306 |
| Деталь: | Drive Haft |
| Парткод: | D014 4194 |
| Деталь: | Core:Hot Roller |
| Парткод: | AE01 0056 |
| Деталь: | Drive Gear - 23Z |
| Парткод: | AB01 4298 |
| Деталь: | Gear:Idler:Drive |
| Парткод: | AB01 4323 |
| Деталь: | Gear:Idler:Hot Roller |
| Парткод: | AB01 4324 |
| Деталь: | Ball Bearing -20x32x7 |
| Парткод: | AE03 0049 |
| Деталь: | Gear - 34Z |
| Парткод: | AB01 4290 |
| Деталь: | COLLAR |
| Парткод: | AA13 2204 |
| Деталь: | Rear Positioning Plate |
| Парткод: | D014 4134 |
| Деталь: | Rear Guide Plate - Fusing Unit |
| Парткод: | D014 4163 |
| Деталь: | AC Harness 2 - Fusing Unit 230V |
| Парткод: | D014 5205 |
| Деталь: | Fusing Belt |
| Парткод: | D014 4090 |
| Деталь: | Hot Roller |
| Парткод: | AE01 0065 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 5206 2684 |
| Деталь: | Thermal Insulating Bushing - 30mm |
| Парткод: | AE03 2031 |
| Деталь: | BALL BEARING |
| Парткод: | AE03 0039 |
| Деталь: | Rear Lever - Heat Roller |
| Парткод: | D014 4141 |
| Деталь: | Guide Ring - Heat Roller |
| Парткод: | D014 4130 |
| Деталь: | HEAT ROLLER |
| Парткод: | AE01 2032 |
| Деталь: | Tension Spring - Heat Roller |
| Парткод: | AA06 2351 |
| Деталь: | Front Lever - Heat Roller |
| Парткод: | D014 4140 |
| Деталь: | Guide Plate Screw |
| Парткод: | AA14 3517 |
| Деталь: | Upper Front Harness - Thermostat |
| Парткод: | D014 4179 |
| Деталь: | Relay Terminal |
| Парткод: | D014 4243 |
| Деталь: | Front Positioning Plate - Stripper |
| Парткод: | D014 4305 |
| Деталь: | FRONT POSITIONING PLATE |
| Парткод: | D014 4133 |
| Деталь: | Collar:Shaft:Drive |
| Парткод: | B132 4125 |
| Деталь: | Roller:Coupling:Knob:Fusing |
| Парткод: | B132 4138 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 3703 |
| Деталь: | Adjusting Pin:Heat Roller |
| Парткод: | D014 4188 |
| Деталь: | Pin:Adjusting Pin:Heat Roller:Peen |
| Парткод: | D014 4185 |
| Деталь: | Seal:Upper:Belt Cleaning |
| Парткод: | B132 6120 |
| Деталь: | Brush:Agitator |
| Парткод: | D014 6497 |
| Деталь: | Bushing:Cutter Unit |
| Парткод: | A571 7653 |
| Деталь: | Seal:Holder:Behind:Belt Cleaning |
| Парткод: | D014 6524 |
| Деталь: | Shield:Case:Holder:Rear |
| Парткод: | D014 6519 |
| Деталь: | Shield:Case:Holder:Front |
| Парткод: | D014 6520 |
| Деталь: | Gear:9Z |
| Парткод: | D014 6484 |
| Деталь: | Gear:14z |
| Парткод: | D014 6482 |
| Деталь: | Snap Ring |
| Парткод: | G011 1058 |
| Деталь: | Gear:16z |
| Парткод: | D014 6480 |
| Деталь: | Entrance Seal:Belt Cleaning |
| Парткод: | D014 6514 |
| Деталь: | Dual Faces Tepe:Entrance Seal: Belt Cleaning |
| Парткод: | D014 6515 |
| Деталь: | Toner Collection Coil |
| Парткод: | D014 6490 |
| Деталь: | Brush:Remove Paper Dust |
| Парткод: | D014 6460 |
| Деталь: | Seal:Scraper:Front:Belt Cleaning |
| Парткод: | D014 6531 |
| Деталь: | Seal:Scraper:Rear:Belt Cleaning |
| Парткод: | D014 6530 |
| Деталь: | Scraper:Brush |
| Парткод: | D014 6462 |
| Деталь: | Seal:Case:Base:Belt Cleaning |
| Парткод: | D014 6525 |
| Деталь: | Seal:Toner Recycling Section |
| Парткод: | D014 6526 |
| Деталь: | Side Plate:Case |
| Парткод: | D014 6504 |
| Деталь: | Bushing:Dia6:Dia8 |
| Парткод: | AA08 3022 |
| Деталь: | Joint:Drive:Brush |
| Парткод: | D014 6476 |
| Деталь: | Shield:Side Plate:Front |
| Парткод: | D014 6506 |
| Деталь: | Shield:Side Plate:Rear |
| Парткод: | D014 6505 |
| Деталь: | Ground Plate:Case |
| Парткод: | D014 6500 |
| Деталь: | Compression Spring:Earth |
| Парткод: | D014 6501 |
| Деталь: | Lens Unit |
| Парткод: | D014 1731 |
| Деталь: | Harness:SBU:SCNB |
| Парткод: | D014 5301 |
| Деталь: | COVER |
| Парткод: | B132 1674 |
| Деталь: | Bracket:Open And Close:Left |
| Парткод: | B132 1871 |
| Деталь: | Rubber Bushing |
| Парткод: | A257 1884 |
| Деталь: | Bracket:Positioning:Left |
| Парткод: | B132 1877 |
| Деталь: | Cushion - Motor |
| Парткод: | AA16 1104 |
| Деталь: | Frame:Front |
| Парткод: | B132 1666 |
| Деталь: | Bracket:Positioning:Right |
| Парткод: | B132 1874 |
| Деталь: | Grip:Application |
| Парткод: | B712 5605 |
| Деталь: | Fan Motor:Mm60 |
| Парткод: | AX64 0151 |
| Деталь: | Bracket:Open And Close:Right |
| Парткод: | B132 1872 |
| Деталь: | Ground Wire:Scanner |
| Парткод: | B132 1896 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Sheet - Photointerrupter |
| Парткод: | A267 1820 |
| Деталь: | Ground Plate:Scanner:Rear |
| Парткод: | B132 1112 |
| Деталь: | Plate:Rod |
| Парткод: | B132 1889 |
| Деталь: | Rod:Open And Close:Scanner Unit |
| Парткод: | B132 1888 |
| Деталь: | FERRITE CORE |
| Парткод: | D014 1888 |
| Деталь: | Cover:Siob |
| Парткод: | D014 1677 |
| Деталь: | Frame:Rear |
| Парткод: | D014 1667 |
| Деталь: | Sheet:Cover:Siob |
| Парткод: | D014 1682 |
| Деталь: | Spring Plate:Earth:Scanner Unit |
| Парткод: | D014 1899 |
| Деталь: | Screw:Spring:Drawer |
| Парткод: | AA14 3794 |
| Деталь: | Spring Connector:9.8n |
| Парткод: | AA06 3670 |
| Деталь: | Bracket:Drawer:Paper Feed Unit |
| Парткод: | B132 1020 |
| Деталь: | Motor:DC24V 17W |
| Парткод: | AX06 0361 |
| Деталь: | Bracket:Sensor |
| Парткод: | B132 1307 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Bracket:Brushless Motor |
| Парткод: | D014 1334 |
| Деталь: | Gear:96Z |
| Парткод: | AB01 0145 |
| Деталь: | Shaft:Drive:Transfer |
| Парткод: | D014 1326 |
| Деталь: | Gear:64Z |
| Парткод: | AB01 0144 |
| Деталь: | Shaft:Drive:Cleaning |
| Парткод: | D014 1331 |
| Деталь: | Gear:46Z/25Z |
| Парткод: | AB01 7746 |
| Деталь: | Gear:25Z/25Z |
| Парткод: | AB01 7747 |
| Деталь: | Gear:25Z |
| Парткод: | AB01 1274 |
| Деталь: | Bracket:Plate |
| Парткод: | D014 1338 |
| Деталь: | Gear:24Z |
| Парткод: | AB01 1273 |
| Деталь: | Toner Recycling Unit |
| Парткод: | D014 1343 |
| Деталь: | Bushing - 8x10x5 |
| Парткод: | AA08 2063 |
| Деталь: | Stud:Bracket |
| Парткод: | D014 1328 |
| Деталь: | Holder:Toner Recycling Unit |
| Парткод: | D014 1350 |
| Деталь: | Harness:Duplex:DRB:Drawer |
| Парткод: | D014 5260 |
| Деталь: | Shaft:Horizontal |
| Парткод: | D014 1345 |
| Деталь: | Cover:Toner Recycling Unit:Shaft |
| Парткод: | D014 1351 |
| Деталь: | Bracket:Spring Plate:Assy |
| Парткод: | B132 7107 |
| Деталь: | Connector Guide Pin |
| Парткод: | AA14 3797 |
| Деталь: | Holder:Drive Unit |
| Парткод: | D014 1344 |
| Деталь: | PCU:K:Exp:Assy |
| Парткод: | D014 3048 |
| Деталь: | PCU:FC:Exp:New:Assy |
| Парткод: | D014 2215 |
| Деталь: | Charge Roller Unit |
| Парткод: | D014 2441 |
| Деталь: | Duct:Charge Corona:Assy |
| Парткод: | D014 2420 |
| Деталь: | CHARGE CORONA UNIT |
| Парткод: | D014 2391 |
| Деталь: | Positioning Plate:PCU |
| Парткод: | B132 2361 |
| Деталь: | Compression Spring - Drum |
| Парткод: | D014 2380 |
| Деталь: | Tension Spring - Coating Bar (K) |
| Парткод: | D014 2325 |
| Деталь: | Tension Spring - Coating Bar (YMC) |
| Парткод: | D014 2326 |
| Деталь: | Right Middle Seal - Bar Bracket |
| Парткод: | D014 2432 |
| Деталь: | Bracket - Coating Bar |
| Парткод: | D014 2327 |
| Деталь: | Seal - Coating Bar Bracket |
| Парткод: | D014 2328 |
| Деталь: | Right Seal - Coating Bar Bracket |
| Парткод: | D014 2349 |
| Деталь: | Drum Lubricant Bar |
| Парткод: | D014 2321 |
| Деталь: | Arm - Coating Bar |
| Парткод: | D014 2324 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Bracket:Photointerruptor |
| Парткод: | D014 4264 |
| Деталь: | Gear:Shaft:Cam |
| Парткод: | AB01 4309 |
| Деталь: | Cam:On-Off:Pressure Roller |
| Парткод: | D014 4297 |
| Деталь: | Feeler |
| Парткод: | D014 4260 |
| Деталь: | SHAFT |
| Парткод: | D014 4261 |
| Деталь: | Bracket:Shaft:Cam |
| Парткод: | D014 4263 |
| Деталь: | Guide:Hook:Lock:Fusing Unit |
| Парткод: | D014 4274 |
| Деталь: | Hook:Lock:Fusing Unit |
| Парткод: | D014 4276 |
| Деталь: | Torsion Spring:Front:2n |
| Парткод: | AA06 6684 |
| Деталь: | Bracket:Lock:Fusing Unit |
| Парткод: | D014 4277 |
| Деталь: | Torsion Spring:Rear:2n |
| Парткод: | AA06 6685 |
| Деталь: | Guide:Hook:Lock:Fusing Unit:Rear |
| Парткод: | D014 4275 |
| Деталь: | Stay:Lock:Fusing Unit |
| Парткод: | D014 4280 |
| Деталь: | Bracket:Side Fence |
| Парткод: | D014 6311 |
| Деталь: | Compression Spring:Stay:On-Off |
| Парткод: | D014 6315 |
| Деталь: | STAY |
| Парткод: | D014 6312 |
| Деталь: | Bracket:Contact Point |
| Парткод: | D014 6310 |
| Деталь: | Shaft:Contact Point |
| Парткод: | D014 6316 |
| Деталь: | Bushing:Back Up:Master Belt |
| Парткод: | G047 3472 |
| Деталь: | Guide Plate:Shaft:Cam:Rear |
| Парткод: | D014 4249 |
| Деталь: | Stay:Fusing Unit:Rear:Exit |
| Парткод: | D014 4259 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 5206 2684 |
| Деталь: | Knob Screw - M4x8 |
| Парткод: | AA14 3424 |
| Деталь: | Sheet:Discharge Lamp |
| Парткод: | D014 2376 |
| Деталь: | Discharge Lamp:Led Array:25MM |
| Парткод: | D014 2278 |
| Деталь: | Seal - Blade Bracket |
| Парткод: | D014 2299 |
| Деталь: | Front Seal - Blade Bracket |
| Парткод: | D014 2301 |
| Деталь: | Raer Seal - Blade Bracket |
| Парткод: | D014 2300 |
| Деталь: | SPRING HOLDER |
| Парткод: | D014 2306 |
| Деталь: | Compression Spring - Blade |
| Парткод: | D014 2305 |
| Деталь: | Seal - Blade Holder |
| Парткод: | D014 2297 |
| Деталь: | Bushing:Blade:Front |
| Парткод: | D014 2303 |
| Деталь: | Bushing:Blade:Rear |
| Парткод: | D014 2302 |
| Деталь: | CLEANING BLADE |
| Парткод: | D014 2352 |
| Деталь: | Cover:Discharge Lamp |
| Парткод: | D014 2479 |
| Деталь: | Seal - Discharge Used Toner |
| Парткод: | D014 2269 |
| Деталь: | Seal - Toner Recycling |
| Парткод: | D014 2276 |
| Деталь: | Shield - Rear Case |
| Парткод: | D014 2268 |
| Деталь: | Transport Screw |
| Парткод: | D014 2281 |
| Деталь: | Collection Coil:Assy |
| Парткод: | D014 2470 |
| Деталь: | Drum Lubricant Supply Brush |
| Парткод: | D014 2335 |
| Деталь: | Joint PCU |
| Парткод: | D014 2338 |
| Деталь: | Tape:Entrance Seal |
| Парткод: | D014 2267 |
| Деталь: | Entrance Seal |
| Парткод: | D014 2266 |
| Деталь: | Gear - 23Z |
| Парткод: | D014 2286 |
| Деталь: | Idler Gear - 23Z |
| Парткод: | D014 2345 |
| Деталь: | Idler Gear - 22Z |
| Парткод: | D014 2346 |
| Деталь: | Brush Roller Holder |
| Парткод: | D014 2340 |
| Деталь: | Gear - 27Z |
| Парткод: | D014 2337 |
| Деталь: | Spring:Earth:Brush Roller |
| Парткод: | D014 2307 |
| Деталь: | Ground Plate - Brush Roller |
| Парткод: | D014 2347 |
| Деталь: | Gear - 17Z |
| Парткод: | D014 2333 |
| Деталь: | Lever - PCU |
| Парткод: | D014 2277 |
| Деталь: | Shield - Front Middle Case |
| Парткод: | D014 2270 |
| Деталь: | Seal - Blade Guide Plate |
| Парткод: | D014 2433 |
| Деталь: | Upper Seal - Blade Guide Plate |
| Парткод: | D014 2377 |
| Деталь: | Lubricant Supply Blade |
| Парткод: | D014 2368 |
| Деталь: | Stayc - PCU Rail |
| Парткод: | D014 2365 |
| Деталь: | Front Seal - Blade Guide Plate |
| Парткод: | D014 2371 |
| Деталь: | Rear Seal - Blade Guide Plate |
| Парткод: | D014 2374 |
| Деталь: | Rear Seal - Frame |
| Парткод: | D014 2288 |
| Деталь: | Seal:Blade:Apply:Rear |
| Парткод: | D014 2438 |
| Деталь: | Seal:Blade:Apply:Rear Middle |
| Парткод: | D014 2439 |
| Деталь: | Front Seal - Duct |
| Парткод: | D014 2271 |
| Деталь: | Seal - Front Frame |
| Парткод: | D014 2279 |
| Деталь: | Seal - Rear Frame |
| Парткод: | D014 2287 |
| Деталь: | Seal:Blade:Apply:Front |
| Парткод: | D014 2436 |
| Деталь: | Seal:Blade:Apply:Front Middle |
| Парткод: | D014 2437 |
| Деталь: | Guide Plate:Left Upper:Assy |
| Парткод: | B132 7115 |
| Деталь: | Roller:MM14 |
| Парткод: | B132 7033 |
| Деталь: | Grip:Guide Plate:Left |
| Парткод: | B132 7015 |
| Деталь: | Guide Plat:Left Lower:Assy |
| Парткод: | B132 7110 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Spring:Guide Plate:Open And Close |
| Парткод: | AA06 3909 |
| Деталь: | Gate Pawl:Reverse:Paper Exit Unit |
| Парткод: | D014 7159 |
| Деталь: | Guide Plate:Middle:Transport |
| Парткод: | B132 7004 |
| Деталь: | NRP345 |
| Парткод: | H020 2318 |
| Деталь: | Arm:Pressure |
| Парткод: | B132 7045 |
| Деталь: | Shaft:Release:Guide Plate |
| Парткод: | B132 7029 |
| Деталь: | Plate:Transport Roller |
| Парткод: | B132 7169 |
| Деталь: | Lever:Release |
| Парткод: | B132 7098 |
| Деталь: | Guide Plate:Middle:Right |
| Парткод: | B132 7017 |
| Деталь: | Roller:Middle |
| Парткод: | B132 7031 |
| Деталь: | Spring Plate:Middle |
| Парткод: | B132 7020 |
| Деталь: | Stay:Supporting Plate |
| Парткод: | B132 7160 |
| Деталь: | Guide:Entrance:Right Rear |
| Парткод: | B132 7103 |
| Деталь: | Stay:Shaft:Assy |
| Парткод: | B132 7097 |
| Деталь: | Lever:Release:Guide Plate:Lower |
| Парткод: | B132 7046 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 2330 |
| Деталь: | DC Solenoid |
| Парткод: | D014 7148 |
| Деталь: | Roller:Middle:Duplex Sub-unit |
| Парткод: | B132 7088 |
| Деталь: | Roller:Drive:Connecting:Reverse |
| Парткод: | D014 7081 |
| Деталь: | Guide Plate:Middle:Assy |
| Парткод: | D014 7027 |
| Деталь: | Inner Cover:Duplex Unit:Assy |
| Парткод: | B132 4525 |
| Деталь: | Decal:Warning (High Temperature) |
| Парткод: | B132 4797 |
| Деталь: | DUPLEX UNIT |
| Парткод: | D014 4501 |
| Деталь: | Grip:Release:Duplex Unit |
| Парткод: | B132 4674 |
| Деталь: | Shaft:Lever:Release |
| Парткод: | B247 4673 |
| Деталь: | Arm:Lock:Duplex |
| Парткод: | B132 4671 |
| Деталь: | Duplex Release Bracket |
| Парткод: | B065 4675 |
| Деталь: | SPRING |
| Парткод: | AA06 2320 |
| Деталь: | Release Lever Bracket |
| Парткод: | B065 4672 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Stay:Duplex Unit:Upper |
| Парткод: | B132 4987 |
| Деталь: | Guide Plate:Jogger:Upper |
| Парткод: | D014 4874 |
| Деталь: | Guide Plate:Duplex:Exit |
| Парткод: | B132 4869 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3811 |
| Деталь: | Table:Duplex:Right |
| Парткод: | B181 4725 |
| Деталь: | Bracket:Sensor:Right |
| Парткод: | B132 4727 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0149 |
| Деталь: | Harness:Sensor:Duplex:3p |
| Парткод: | D014 5263 |
| Деталь: | GUIDE PLATE:TRANSPORT:LOWER |
| Парткод: | B132 4730 |
| Деталь: | Spring Plate - Driven Roller |
| Парткод: | B065 4731 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 2077 |
| Деталь: | Guide Plate Band |
| Парткод: | A096 4928 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3581 |
| Деталь: | Guide Plate Pressure Holder |
| Парткод: | A229 4727 |
| Деталь: | Guide Stopper Roller |
| Парткод: | AF02 2067 |
| Деталь: | Guide Plate Lever |
| Парткод: | B065 4531 |
| Деталь: | Decal - Guide Plate Lever |
| Парткод: | B065 4867 |
| Деталь: | Guide Plate Lever Hook |
| Парткод: | B065 4933 |
| Деталь: | Cover:Manual Feed:Machine or Copier |
| Парткод: | B132 2816 |
| Деталь: | Decal - Inkjet:Manual Feed |
| Парткод: | B132 1482 |
| Деталь: | Manual Feed Table:Assy |
| Парткод: | D014 2810 |
| Деталь: | Side Fence:Auxiliary:Front |
| Парткод: | B132 2863 |
| Деталь: | Side Fence:Auxiliary:Rear |
| Парткод: | B132 2866 |
| Деталь: | Side Fence:Front:Assy |
| Парткод: | B132 2861 |
| Деталь: | Side Fence:Rear:Assy |
| Парткод: | B132 2864 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | B132 2875 |
| Деталь: | Guide:Manual Feed Table |
| Парткод: | B132 2868 |
| Деталь: | Rear Rack |
| Парткод: | A232 6083 |
| Деталь: | Gear - 16Z |
| Парткод: | G011 3305 |
| Деталь: | Paper size sensor |
| Парткод: | B132 2872 |
| Деталь: | Friction Pad:Side Fence:Front |
| Парткод: | D014 2870 |
| Деталь: | Stepper Motor:Paper Feed Unit:Assy |
| Парткод: | B132 6655 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0958 |
| Деталь: | Bracket:Drive:Paper Feed Sub-unit |
| Парткод: | B132 2760 |
| Деталь: | Timing Pulley:35T |
| Парткод: | AB03 0301 |
| Деталь: | Timing Belt:40S2M150 |
| Парткод: | AA04 3313 |
| Деталь: | Spacer - 1x8x12 |
| Парткод: | AA13 2025 |
| Деталь: | Ball Bearing - 8x12x5 |
| Парткод: | A247 2800 |
| Деталь: | Harness:PSU:Fusing:100V |
| Парткод: | D014 5371 |
| Деталь: | AC/DC Harness - PSU-Fusing 200V |
| Парткод: | D014 5373 |
| Деталь: | Harness - PSU 230V |
| Парткод: | D014 5374 |
| Деталь: | Gear:86Z |
| Парткод: | D014 1372 |
| Деталь: | Shaft:Drive:Vacuum |
| Парткод: | B132 1367 |
| Деталь: | Gear:22Z |
| Парткод: | AB01 1250 |
| Деталь: | Motor:DC24V 48W |
| Парткод: | AX06 0362 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3301 |
| Деталь: | Timing Pulley:47T |
| Парткод: | AB03 0770 |
| Деталь: | Timing Pulley:47T |
| Парткод: | AB03 0768 |
| Деталь: | Gear:80Z/30T |
| Парткод: | D014 1371 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 0951 |
| Деталь: | Bracket:Tightener:Assy |
| Парткод: | B132 1356 |
| Деталь: | Shaft:Drive:Fusing:Assy |
| Парткод: | B132 1360 |
| Деталь: | Pulley:Idler |
| Парткод: | B132 1370 |
| Деталь: | Timing Belt:40S3M471 |
| Парткод: | AA04 3965 |
| Деталь: | Timing Belt:60S3M741 |
| Парткод: | AA04 3964 |
| Деталь: | Timing Pulley:44t |
| Парткод: | AB03 0771 |
| Деталь: | Timing Pulley:44t |
| Парткод: | AB03 0772 |
| Деталь: | Shaft:Drive:Reverse:Assy |
| Парткод: | B132 1363 |
| Деталь: | Bracket:Drive:Fusing Unit |
| Парткод: | D014 1380 |
| Деталь: | Gear:40Z |
| Парткод: | AB01 1304 |
| Деталь: | Gear:30Z |
| Парткод: | AB01 1302 |
| Деталь: | Bracket:Gear:Swivel |
| Парткод: | B132 2679 |
| Деталь: | Spacer:MM12 |
| Парткод: | B132 2699 |
| Деталь: | Shaft:Drive:Paper Feed |
| Парткод: | B132 2762 |
| Деталь: | Gear:33Z |
| Парткод: | AB01 1303 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Cam:On-Off |
| Парткод: | B132 6111 |
| Деталь: | Shaft:Cam:Color |
| Парткод: | B132 6112 |
| Деталь: | Shaft:Positioning |
| Парткод: | B132 6094 |
| Деталь: | Roller:Opposed:Belt Cleaning |
| Парткод: | D014 6190 |
| Деталь: | Roller:Opposed:Transfer:Paper |
| Парткод: | D014 6073 |
| Деталь: | Roller:Transfer:Front |
| Парткод: | B132 6069 |
| Деталь: | Roller:Drive |
| Парткод: | D014 6055 |
| Деталь: | Shaft:Cam |
| Парткод: | D014 6123 |
| Деталь: | Cam:On-Off:Black |
| Парткод: | B132 6114 |
| Деталь: | Gear:16z |
| Парткод: | B132 6130 |
| Деталь: | Holder:Opposed:Rear:Assy |
| Парткод: | B132 6150 |
| Деталь: | Plate:Intermediate Transfer:Front |
| Парткод: | B132 6134 |
| Деталь: | Holder:Opposed:Transfer:Front |
| Парткод: | B132 6143 |
| Деталь: | Grip:On-Off |
| Парткод: | B132 6132 |
| Деталь: | Joint:Intermediate Transfer:Front:Assy |
| Парткод: | B132 6175 |
| Деталь: | Compression Spring: Plate:Intermediate Transfe |
| Парткод: | B132 6136 |
| Деталь: | Cam:On-Off |
| Парткод: | D014 6119 |
| Деталь: | Roller:Opposed:Density Sensor |
| Парткод: | D014 6065 |
| Деталь: | Retaining Ring:Silencer:MM7 |
| Парткод: | AA10 0011 |
| Деталь: | Spacer:Opposed:Transfer:Paper |
| Парткод: | D014 6014 |
| Деталь: | Shielding Plate:Black |
| Парткод: | D014 6151 |
| Деталь: | Tandem LCT:Right:NA:Assy |
| Парткод: | D014 7506 |
| Деталь: | Tandem LCT:Right:EU:Assy |
| Парткод: | D014 7505 |
| Деталь: | Inner Cover:Tandem LCT |
| Парткод: | B132 7586 |
| Деталь: | Decal - Caution |
| Парткод: | AA00 2246 |
| Деталь: | Right Stopper |
| Парткод: | B065 6859 |
| Деталь: | Protection -inner Cover |
| Парткод: | B065 6875 |
| Деталь: | Decal - Paper Set - Right |
| Парткод: | B065 6877 |
| Деталь: | Side Fence - Right Front |
| Парткод: | B234 6686 |
| Деталь: | Plate:Paper:Assy |
| Парткод: | B234 6690 |
| Деталь: | Base:Tandem LCT:Right |
| Парткод: | B132 7543 |
| Деталь: | Friction pad |
| Парткод: | 5201 2858 |
| Деталь: | Sensor bracket |
| Парткод: | A294 6706 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Misfeed Removal Guide |
| Парткод: | A176 6695 |
| Деталь: | Shield:Tandem LCT:Rear Right |
| Парткод: | B475 6855 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA00 2010 |
| Деталь: | Side Fence:Tandem LCT:Right |
| Парткод: | B132 7576 |
| Деталь: | Side plate |
| Парткод: | A294 6666 |
| Деталь: | Decal - Right Paper Set |
| Парткод: | A096 6677 |
| Деталь: | Guide Plate - Upper Heat Sink |
| Парткод: | A248 6103 |
| Деталь: | Heater:115V:18W:Upper |
| Парткод: | AX40 0176 |
| Деталь: | Heater:240V:18W:Upper |
| Парткод: | AX40 0178 |
| Деталь: | Heat Sink:Heater:Upper:Fiber |
| Парткод: | B070 6293 |
| Деталь: | Supporting Plate:Stay |
| Парткод: | B132 6669 |
| Деталь: | Slide Rail:Tandem LCT |
| Парткод: | AA07 0072 |
| Деталь: | Slidebracket |
| Парткод: | B065 6774 |
| Деталь: | Stay:Tandem LCT |
| Парткод: | B132 6696 |
| Деталь: | Rail:Tandem LCT:Left:Assy |
| Парткод: | B132 7590 |
| Деталь: | Left Rail Bracket |
| Парткод: | B132 6742 |
| Деталь: | Lock Arm - Tandem Tray |
| Парткод: | B065 6135 |
| Деталь: | SPRING |
| Парткод: | AA06 0761 |
| Деталь: | Side Plate:Front:Paper Bank |
| Парткод: | B132 6689 |
| Деталь: | Rail:Paper Tray:Assy |
| Парткод: | B132 7591 |
| Деталь: | Seal - Misfeed Removal |
| Парткод: | AA15 0406 |
| Деталь: | Bracket:Holder:Assy |
| Парткод: | B132 6630 |
| Деталь: | Rail - Side Fence |
| Парткод: | G564 4151 |
| Деталь: | Table Side Fence |
| Парткод: | B477 2272 |
| Деталь: | Side Fence Pad |
| Парткод: | A376 4599 |
| Деталь: | Original Sensor Feeler Stud |
| Парткод: | B477 2286 |
| Деталь: | Original Sensor Feeler |
| Парткод: | A806 1351 |
| Деталь: | Snap Ring |
| Парткод: | 5206 2686 |
| Деталь: | Base:Original Table:Assy |
| Парткод: | B652 2351 |
| Деталь: | Decal:Base:Original |
| Парткод: | B652 2354 |
| Деталь: | Harness:Original Sensor |
| Парткод: | B652 5451 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Original Sensor Bracket |
| Парткод: | B477 2281 |
| Деталь: | Photo Refiection Sensor:Original Table |
| Парткод: | AW01 0112 |
| Деталь: | Shaft:Rise:Base |
| Парткод: | B652 2333 |
| Деталь: | Bushing - 8mm |
| Парткод: | A628 1225 |
| Деталь: | Lever:Rise:Base |
| Парткод: | B652 2334 |
| Деталь: | Bracket:Lever:Rise:Base |
| Парткод: | B652 2335 |
| Деталь: | Shaft:Base:Rear:Assy |
| Парткод: | B652 2363 |
| Деталь: | Arm:Roller:Reverse:Upper |
| Парткод: | B652 2403 |
| Деталь: | Pressure Roller - Reverse |
| Парткод: | B351 3752 |
| Деталь: | Compression Spring:3.1n |
| Парткод: | B652 2404 |
| Деталь: | Bushing - 8mm |
| Парткод: | 5053 0223 |
| Деталь: | Ground Plate:Shaft:Base |
| Парткод: | B652 2323 |
| Деталь: | Bushing:Original Table |
| Парткод: | B652 2375 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Discharge Brush |
| Парткод: | A859 3225 |
| Деталь: | Stopper:Original Table |
| Парткод: | B652 2392 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 2393 |
| Деталь: | Guide Plate:Reverse:Upper |
| Парткод: | B652 2322 |
| Деталь: | Snap Ring |
| Парткод: | C101 2360 |
| Деталь: | Gear - Z47 |
| Парткод: | A806 2281 |
| Деталь: | Shaft:Cleaner |
| Парткод: | AA14 3789 |
| Деталь: | Original Table:Face Front:Printing |
| Парткод: | B652 2372 |
| Деталь: | Original Table:Behind |
| Парткод: | B652 2383 |
| Деталь: | Harness:Sensor:Original Table |
| Парткод: | B652 5436 |
| Деталь: | Cushion:Base:Behind |
| Парткод: | B477 2263 |
| Деталь: | Sheet:Cushion:Base |
| Парткод: | B477 2264 |
| Деталь: | Hinge:C/T Box:Upper |
| Парткод: | B132 5933 |
| Деталь: | Hinge:C/T Box:Lower |
| Парткод: | B132 5930 |
| Деталь: | Arm:Hinge:C/T Box |
| Парткод: | B132 5947 |
| Деталь: | Right Frame - C/T Box |
| Парткод: | D014 5921 |
| Деталь: | Bracket - IPU/VBCU |
| Парткод: | D014 5955 |
| Деталь: | Lowr Frame - C/T Box |
| Парткод: | B132 5951 |
| Деталь: | Ground Plate:Base:Control Board |
| Парткод: | B132 5807 |
| Деталь: | Supporter:Lower |
| Парткод: | D014 5953 |
| Деталь: | Supporter:Upper |
| Парткод: | D014 5952 |
| Деталь: | Base - C/T Box |
| Парткод: | D014 5951 |
| Деталь: | Large Drum Stay Ground Plate |
| Парткод: | B070 6877 |
| Деталь: | Left Frame - C/T Box |
| Парткод: | D014 5931 |
| Деталь: | Guard:GAP:C/T Box |
| Парткод: | B132 1528 |
| Деталь: | Decal:Caption:Interface |
| Парткод: | D014 5818 |
| Деталь: | Upper Frame - C/T Box |
| Парткод: | D014 5911 |
| Деталь: | Seal:C/T Box:Upper:Side |
| Парткод: | B132 5813 |
| Деталь: | Grip:Application |
| Парткод: | B712 5605 |
| Деталь: | Stopper:C/T Box:Upper |
| Парткод: | B132 5989 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3718 |
| Деталь: | Bracket:C/T Box:Upper |
| Парткод: | B132 5940 |
| Деталь: | Cover:Left Upper |
| Парткод: | B132 1503 |
| Деталь: | Screw:M4:Dia5 |
| Парткод: | AA14 3559 |
| Деталь: | Exposure Glass |
| Парткод: | BC01 2008 |
| Деталь: | SEAL |
| Парткод: | B065 1782 |
| Деталь: | Scale Bracket |
| Парткод: | B065 1787 |
| Деталь: | Scale Bracket Seal |
| Парткод: | B065 1773 |
| Деталь: | Cushion - 0.5 |
| Парткод: | AA16 1137 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 5442 1924 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Left Scale |
| Парткод: | B065 1772 |
| Деталь: | Scale:Sheet Through |
| Парткод: | B132 1687 |
| Деталь: | Scale:Sheet Through:Assy |
| Парткод: | B132 1686 |
| Деталь: | Exposure Glass |
| Парткод: | A250 1752 |
| Деталь: | Scale:Rear:Printing |
| Парткод: | B132 1692 |
| Деталь: | Bracket:ADF |
| Парткод: | B132 1885 |
| Деталь: | Decal - Copy:Original |
| Парткод: | B132 1583 |
| Деталь: | Cover:Right Upper |
| Парткод: | B132 1502 |
| Деталь: | RIGHT STAY |
| Парткод: | B065 1785 |
| Деталь: | Spring Plate:Ground Plate:ADF |
| Парткод: | B132 1898 |
| Деталь: | Mylar:Frame:Front |
| Парткод: | B132 1683 |
| Деталь: | Mylar:Frame:Middle |
| Парткод: | B132 1684 |
| Деталь: | Mylar:Frame:Rear |
| Парткод: | B132 1685 |
| Деталь: | DC Solenoid:End Fence:Front:Assy |
| Парткод: | B132 7547 |
| Деталь: | Hook - Tension Sprong |
| Парткод: | A248 6713 |
| Деталь: | Tension Spring - Long |
| Парткод: | AA06 0757 |
| Деталь: | End Fence - Front |
| Парткод: | B234 6612 |
| Деталь: | Base:Tandem LCT:Right:Welding |
| Парткод: | B132 7545 |
| Деталь: | End Fence - Rear |
| Парткод: | B234 6625 |
| Деталь: | Guide Plate - End Fence |
| Парткод: | B234 6630 |
| Деталь: | DC Solenoid:End Fence:Rear:Assy |
| Парткод: | B132 7571 |
| Деталь: | Right Rear Side Plate |
| Парткод: | A294 6676 |
| Деталь: | On Off Detector Bracket - Rear |
| Парткод: | B234 6621 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Right Drive Shaft |
| Парткод: | A248 6687 |
| Деталь: | Wire Ring |
| Парткод: | A248 6694 |
| Деталь: | Stay -rightbase |
| Парткод: | B065 6870 |
| Деталь: | End Fence Cover Front |
| Парткод: | B070 6667 |
| Деталь: | Tension Spring - Short |
| Парткод: | AA06 0758 |
| Деталь: | Lever:Release:Front |
| Парткод: | B070 6683 |
| Деталь: | On Off Detector Bracket - Front |
| Парткод: | B234 6620 |
| Деталь: | Wire Pulley - M10 |
| Парткод: | AB03 2058 |
| Деталь: | Guide - Pulley |
| Парткод: | A248 6695 |
| Деталь: | Pulley - M10 |
| Парткод: | AB03 2719 |
| Деталь: | Cover:Pulley:Drive Were |
| Парткод: | B132 7550 |
| Деталь: | Gear - 30Z |
| Парткод: | AB01 3781 |
| Деталь: | Bushing - 8mm |
| Парткод: | 5053 0223 |
| Деталь: | Oil Damper Bracket |
| Парткод: | B065 6872 |
| Деталь: | OIL DAMPER |
| Парткод: | A248 6701 |
| Деталь: | Side Plate:Tandem:Right Front |
| Парткод: | B070 6668 |
| Деталь: | Front Roller - Slide Rail |
| Парткод: | A294 6655 |
| Деталь: | Cushion - Small |
| Парткод: | AA16 1130 |
| Деталь: | Feeler - Paper Height Sensor |
| Парткод: | A294 6690 |
| Деталь: | Small Lever |
| Парткод: | B065 6864 |
| Деталь: | Roller - Slide Rail |
| Парткод: | AF02 2105 |
| Деталь: | Spacer - 6mm |
| Парткод: | AA13 2203 |
| Деталь: | Large Lever |
| Парткод: | B065 6862 |
| Деталь: | Lever:Release:Rear |
| Парткод: | B070 6684 |
| Деталь: | Cushion - Large |
| Парткод: | AA16 1129 |
| Деталь: | SENSOR |
| Парткод: | AW01 0113 |
| Деталь: | Bracket:Connector:Tandem LCT |
| Парткод: | B132 7575 |
| Деталь: | Harness - Tandem LCT Right |
| Парткод: | B234 5673 |
| Деталь: | Paper Volume Shield Plate |
| Парткод: | B065 6717 |
| Деталь: | Slide Rail:Right:Assy |
| Парткод: | B132 6693 |
| Деталь: | Decal:Paper Tray:Display:3 |
| Парткод: | AA00 3213 |
| Деталь: | Decal:Paper Tray:Display:2 |
| Парткод: | AA00 3212 |
| Деталь: | Slide Rail:Left:Sub-assy |
| Парткод: | B132 6692 |
| Деталь: | Paper Tray Cover - Long |
| Парткод: | B247 6632 |
| Деталь: | Paper Tray Cover - Short |
| Парткод: | B247 6633 |
| Деталь: | Left Support Plate |
| Парткод: | B065 6589 |
| Деталь: | Right Support Plate |
| Парткод: | B065 6588 |
| Деталь: | Paper Tray Holder Base |
| Парткод: | B065 6591 |
| Деталь: | Stay:Holder:Paper Tray:Assy |
| Парткод: | B132 6653 |
| Деталь: | Total Counter:7FIG:24V:MI2 |
| Парткод: | AX31 0047 |
| Деталь: | Bracket:Total Counter |
| Парткод: | B132 5976 |
| Деталь: | Decal:Total Counter |
| Парткод: | B132 5996 |
| Деталь: | Base:Slide Rail:No.2:Peen |
| Парткод: | B247 6781 |
| Деталь: | Tray Lock Spring - 19mm |
| Парткод: | AA06 0534 |
| Деталь: | Tray Lock Arm |
| Парткод: | B065 6136 |
| Деталь: | Base:Slide Rail:No.3:Peen |
| Парткод: | B247 6783 |
| Деталь: | Grip - Paper Tray Cover |
| Парткод: | B247 6634 |
| Деталь: | Operation Panel - NA |
| Парткод: | D014 7201 |
| Деталь: | Operation Panel - EU |
| Парткод: | D014 7202 |
| Деталь: | PCB:OP-R |
| Парткод: | D009 1470 |
| Деталь: | Harness:OP-L:12 |
| Парткод: | D009 1482 |
| Деталь: | Harness:OP-L:13 |
| Парткод: | D009 1483 |
| Деталь: | Keytop - Kantan |
| Парткод: | B238 1552 |
| Деталь: | Keytop - Login |
| Парткод: | B238 1550 |
| Деталь: | Keytop - Power Source |
| Парткод: | B238 1549 |
| Деталь: | Keytop - Start |
| Парткод: | B238 1504 |
| Деталь: | Keytop - Try Print |
| Парткод: | B238 1506 |
| Деталь: | Keytop - Interrupt |
| Парткод: | B238 1509 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B223 1520 |
| Деталь: | Keytop:10key:NA |
| Парткод: | B223 1540 |
| Деталь: | Keytop:10key |
| Парткод: | B223 1521 |
| Деталь: | Keytop - Clear Modes |
| Парткод: | B238 1583 |
| Деталь: | LCDC Board - NA |
| Парткод: | D014 5191 |
| Деталь: | LCDC Board - EU |
| Парткод: | D014 5192 |
| Деталь: | Cable:FFC:TFT:LCD |
| Парткод: | D009 1487 |
| Деталь: | Harness:Invertor |
| Парткод: | D009 1484 |
| Деталь: | Invertor:TFT |
| Парткод: | D009 1486 |
| Деталь: | Shadeing Plate:Touch Panel |
| Парткод: | D009 1504 |
| Деталь: | Touch Panel:W-VGA:MA |
| Парткод: | D009 1488 |
| Деталь: | LCD Spacer B |
| Парткод: | B238 1535 |
| Деталь: | LCD Spacer A |
| Парткод: | B238 1534 |
| Деталь: | LCD:TFT:W -VGA:SH |
| Парткод: | D009 1489 |
| Деталь: | PCB OP-L |
| Парткод: | B223 1475 |
| Деталь: | Harness:OP-R:13 |
| Парткод: | D009 1481 |
| Деталь: | Harness:OP-R:10 |
| Парткод: | D009 1480 |
| Деталь: | Lens:Front |
| Парткод: | D014 7223 |
| Деталь: | Spacer - Keytop |
| Парткод: | B238 1547 |
| Деталь: | Keytop - Counter |
| Парткод: | B238 1511 |
| Деталь: | Keytop - Blank FB |
| Парткод: | B223 1518 |
| Деталь: | Keytop - Doc NA |
| Парткод: | B223 1529 |
| Деталь: | Keytop:Doc:EU |
| Парткод: | B223 1535 |
| Деталь: | Keytop - Copy NA |
| Парткод: | B223 1528 |
| Деталь: | Keytop:Copy:EU |
| Парткод: | B223 1534 |
| Деталь: | Decal - Inkjet:Paper |
| Парткод: | B132 1562 |
| Деталь: | Keytop:Scanner:EU |
| Парткод: | B223 1538 |
| Деталь: | Keytop:Printer:EU |
| Парткод: | B223 1537 |
| Деталь: | Harness:Upper Front |
| Парткод: | D014 5375 |
| Деталь: | Harness:Upper Rear |
| Парткод: | D014 5231 |
| Деталь: | Harness:Siob:VBCU |
| Парткод: | D014 5306 |
| Деталь: | Harness:Middle |
| Парткод: | D014 5379 |
| Деталь: | Harness:DRB:VBCU:Power Source |
| Парткод: | D014 5213 |
| Деталь: | Harness:VBCU:PP1:pFB |
| Парткод: | D014 5381 |
| Деталь: | PCB:VBCU |
| Парткод: | D014 5133 |
| Деталь: | Fan Motor MM80 |
| Парткод: | AX64 0159 |
| Деталь: | Harness:HDD:Fan Motor |
| Парткод: | D014 5386 |
| Деталь: | Bracket:Fan Motor |
| Парткод: | B132 5944 |
| Деталь: | PCB:IPU |
| Парткод: | D014 5422 |
| Деталь: | Interface Cable:Scanner: Image Processing Unit |
| Парткод: | D014 5305 |
| Деталь: | Cable:LVDS:LDB |
| Парткод: | D014 5367 |
| Деталь: | Bracket:Knob:Fusing |
| Парткод: | D014 1150 |
| Деталь: | Gear:18Z |
| Парткод: | AB01 3309 |
| Деталь: | Collar:DIA18 |
| Парткод: | B132 1235 |
| Деталь: | Gear:13/20Z |
| Парткод: | AB01 7688 |
| Деталь: | Shaft:Knob:Fusing |
| Парткод: | D014 1156 |
| Деталь: | Gear - 16Z |
| Парткод: | AB01 3363 |
| Деталь: | Guide Plate:Fusing Unit |
| Парткод: | D014 1154 |
| Деталь: | Motor:DC24V 24W |
| Парткод: | AX06 0357 |
| Деталь: | Bracket:Motor:On-Off:Press Fit |
| Парткод: | D014 4265 |
| Деталь: | Gear:Motor:On-Off |
| Парткод: | AB01 4310 |
| Деталь: | Shaft:Motor |
| Парткод: | D014 4268 |
| Деталь: | Bracket:Gear:Slow Down:Press Fit |
| Парткод: | D014 4351 |
| Деталь: | Gear:Coupling:Slow Down:21Z |
| Парткод: | AB01 4311 |
| Деталь: | Shaft:Gear:Slow Down |
| Парткод: | D014 4350 |
| Деталь: | Gear:Motor:Drive:15Z |
| Парткод: | AB01 4312 |
| Деталь: | Feeler |
| Парткод: | D014 6322 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Bracket:Sensor |
| Парткод: | D014 6325 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | DC Motor:Agitate:Assy |
| Парткод: | B132 6511 |
| Деталь: | Bracket:Motor |
| Парткод: | D014 6318 |
| Деталь: | Gear:15Z/24Z |
| Парткод: | D014 6323 |
| Деталь: | Gear:45Z |
| Парткод: | D014 6324 |
| Деталь: | Shaft:Cam |
| Парткод: | D014 6321 |
| Деталь: | CAM |
| Парткод: | D014 6326 |
| Деталь: | Image Transfer Belt Unit |
| Парткод: | D014 6001 |
| Деталь: | Harness:High Voltage Supply Cord:MCY |
| Парткод: | D014 5352 |
| Деталь: | Terminal:Collar |
| Парткод: | B132 6140 |
| Деталь: | Terminal:Yellow |
| Парткод: | B132 6149 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | D014 6147 |
| Деталь: | Plate:Upper:Positioning Sensor |
| Парткод: | D014 6168 |
| Деталь: | Positioning Sensor |
| Парткод: | D014 6141 |
| Деталь: | Image Transfer Belt |
| Парткод: | D014 6050 |
| Деталь: | Harness:Positioning Sensor |
| Парткод: | D014 5378 |
| Деталь: | Bushing:Intermediate Transfer |
| Парткод: | D014 6116 |
| Деталь: | Bushing:Intermediate Transfer |
| Парткод: | D014 6115 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | D014 6144 |
| Деталь: | Roller:Driven |
| Парткод: | B132 6061 |
| Деталь: | Roller:Intermediate Transfer |
| Парткод: | D014 6080 |
| Деталь: | Bracket:Collar |
| Парткод: | B132 6077 |
| Деталь: | Harness:High Voltage Supply Cord:K |
| Парткод: | D014 5351 |
| Деталь: | Terminal:Black |
| Парткод: | B132 6137 |
| Деталь: | Shaft:Contact Point:Collar |
| Парткод: | B132 6098 |
| Деталь: | Spring:Transfer:Black:Front |
| Парткод: | D014 6135 |
| Деталь: | Bracket:On-off:Black |
| Парткод: | B132 6076 |
| Деталь: | Snap Ring - Pick Up |
| Парткод: | G014 3291 |
| Деталь: | Spring:Transfer:Black:Rear |
| Парткод: | D014 6136 |
| Деталь: | PCB:Control Board:Ex1 |
| Парткод: | D014 5711 |
| Деталь: | Decal:Caution:HDD:Fan |
| Парткод: | B132 5819 |
| Деталь: | Seal:C/T Box:Cover:Middle |
| Парткод: | B132 5809 |
| Деталь: | Seal:C/T Box:Cover:Side |
| Парткод: | B132 5812 |
| Деталь: | Sheet:Cover:C/T Box |
| Парткод: | B132 5832 |
| Деталь: | HDD UNIT |
| Парткод: | D014 5720 |
| Деталь: | Cable:HDD:Power |
| Парткод: | D014 5783 |
| Деталь: | Cable:HDD:Gray |
| Парткод: | D014 5782 |
| Деталь: | Cable:HDD:Red |
| Парткод: | D014 5781 |
| Деталь: | Bracket:Control Board |
| Парткод: | D014 5971 |
| Деталь: | Cover:SD-Card |
| Парткод: | D014 5973 |
| Деталь: | Panel Knob Screw |
| Парткод: | AA14 1008 |
| Деталь: | Panel -Interface |
| Парткод: | B132 5835 |
| Деталь: | Cover:Connector:EFI |
| Парткод: | D014 5974 |
| Деталь: | Cover:Control Board:Usb |
| Парткод: | D014 5977 |
| Деталь: | PCB:PC4200:RAWCard-A:1GB |
| Парткод: | G178 6072 |
| Деталь: | NVRAM |
| Парткод: | D014 9590 |
| Деталь: | PCB:PC4200:RAWCard-C:512MB |
| Парткод: | G178 6062 |
| Деталь: | Large Drum Stay Ground Plate |
| Парткод: | B070 6877 |
| Деталь: | Gasket:Cover:C/T Box |
| Парткод: | B132 5831 |
| Деталь: | Cover - C/T Box |
| Парткод: | D014 5816 |
| Деталь: | SD-Card - P/S Unit |
| Парткод: | D376 5017 |
| Деталь: | Paper Feed Unit:Paper Bank |
| Парткод: | B132 6621 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF03 0081 |
| Деталь: | Paper Feed Roller:Feed |
| Парткод: | AF03 1082 |
| Деталь: | Pick-up Gear Cover |
| Парткод: | B065 6350 |
| Деталь: | Idler Gear |
| Парткод: | AB01 1465 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Pick-up Arm |
| Парткод: | B065 6357 |
| Деталь: | SPRING |
| Парткод: | AA06 0898 |
| Деталь: | Feed Roller Shaft |
| Парткод: | AA14 0828 |
| Деталь: | Feed Lever |
| Парткод: | B065 6445 |
| Деталь: | SPRING |
| Парткод: | AA06 0897 |
| Деталь: | Paper Feed Sensor Bracket |
| Парткод: | B065 6358 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Feed Stay |
| Парткод: | B065 6364 |
| Деталь: | Harness - Paper Feed Unit Upper |
| Парткод: | B132 7581 |
| Деталь: | SPRING |
| Парткод: | AA06 0899 |
| Деталь: | DC Solenoid:Pickup:Assy |
| Парткод: | B132 6659 |
| Деталь: | Gear - 21Z/38Z |
| Парткод: | AB01 7617 |
| Деталь: | Paper End Sensor Bracket |
| Парткод: | B065 6345 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Harness - Paper Feed Unit Lower |
| Парткод: | B132 7580 |
| Деталь: | Paper Feed Guide Plate |
| Парткод: | B140 6339 |
| Деталь: | Transport Roller |
| Парткод: | AF02 0562 |
| Деталь: | Gear - 35Z |
| Парткод: | AB01 1466 |
| Деталь: | Heat Sink Base |
| Парткод: | B065 6334 |
| Деталь: | Heat Sink Spring |
| Парткод: | AA06 3889 |
| Деталь: | HEAT SINK |
| Парткод: | B065 6337 |
| Деталь: | Heat Sink Sheet |
| Парткод: | B065 6338 |
| Деталь: | Paper Feed Unit Stay |
| Парткод: | B065 6375 |
| Деталь: | Drive bracket |
| Парткод: | B065 6366 |
| Деталь: | Feed Gear Cover |
| Парткод: | B065 6353 |
| Деталь: | Driven Pressure Lever |
| Парткод: | B065 6457 |
| Деталь: | SPRING |
| Парткод: | AA06 0896 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3718 |
| Деталь: | Case:Remove Paper Dust |
| Парткод: | B132 2605 |
| Деталь: | Bracket:Remove Paper Dust |
| Парткод: | D014 2601 |
| Деталь: | Bracket:Registration Sensor |
| Парткод: | D014 2620 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Harness:Pull Out:Uni:26pin |
| Парткод: | D014 5245 |
| Деталь: | Optics Sensor:Photo |
| Парткод: | AW00 0011 |
| Деталь: | Stud:Contact Point |
| Парткод: | B132 2703 |
| Деталь: | Registration Guide:Upper |
| Парткод: | D014 2631 |
| Деталь: | Lever:Un Lock |
| Парткод: | B132 2671 |
| Деталь: | Bushing - 4x6x7mm |
| Парткод: | 5443 2668 |
| Деталь: | Tension Spring:Open And Close |
| Парткод: | AA06 1025 |
| Деталь: | Tension Spring:Registration |
| Парткод: | AA06 1033 |
| Деталь: | Side Plate:Open And Close:Front |
| Парткод: | B132 2674 |
| Деталь: | Shaft:Lock |
| Парткод: | B132 2670 |
| Деталь: | Lever:Knob:Release |
| Парткод: | B132 2644 |
| Деталь: | Registration Guide:Upper |
| Парткод: | B132 2682 |
| Деталь: | Shaft:Contact Point:Lever |
| Парткод: | B132 2681 |
| Деталь: | Knob:Release |
| Парткод: | B132 2651 |
| Деталь: | Registration Guide:Connecting |
| Парткод: | B132 2680 |
| Деталь: | Side Plate:Open And Close:Rear:Peen |
| Парткод: | D014 2669 |
| Деталь: | Cover:Drive Sub-unit |
| Парткод: | B132 1188 |
| Деталь: | Harness:Pull Out:Uni:Dehumidifier |
| Парткод: | D014 5265 |
| Деталь: | Screw:Drawer |
| Парткод: | AA14 3792 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Stay:Frame:Left |
| Парткод: | B477 1152 |
| Деталь: | Arm Shaft |
| Парткод: | B477 1171 |
| Деталь: | Screw:DIA6:14.5:M4 |
| Парткод: | AA14 3842 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 1136 |
| Деталь: | Hinge:Left:Assy |
| Парткод: | B652 1210 |
| Деталь: | Contact Point Shaft |
| Парткод: | A806 1135 |
| Деталь: | Right Frame Stay |
| Парткод: | B477 1161 |
| Деталь: | Sheet:Exit:Lower |
| Парткод: | B652 1135 |
| Деталь: | Hinge:Right:Assy |
| Парткод: | B652 1220 |
| Деталь: | Sensor Feeler |
| Парткод: | B477 1185 |
| Деталь: | Sensor bracket |
| Парткод: | B477 1181 |
| Деталь: | Detection Sensor Harness |
| Парткод: | B477 5611 |
| Деталь: | Harness:Sensor:Reverse:Upper |
| Парткод: | B652 5446 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B477 2621 |
| Деталь: | Bracket:Pressure:Transport Belt |
| Парткод: | B652 1131 |
| Деталь: | TENSION SPRING |
| Парткод: | B652 1132 |
| Деталь: | Pulley:Belt Tensioner |
| Парткод: | A257 6112 |
| Деталь: | Cover:Roller:Scanning:Peen |
| Парткод: | B652 3136 |
| Деталь: | Bracket:Magnet Catch:Pressure Plate |
| Парткод: | B652 4904 |
| Деталь: | Front Left Stopper |
| Парткод: | B477 1191 |
| Деталь: | Adjusting Pin:Transport Belt Unit |
| Парткод: | B652 1141 |
| Деталь: | Screw:Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Shoulder Screw - Front Cover |
| Парткод: | AA14 3129 |
| Деталь: | SPRING |
| Парткод: | AA06 2318 |
| Деталь: | Decal:Grip:E3 |
| Парткод: | B132 4796 |
| Деталь: | Lever:Open And Close:Reverse Unit |
| Парткод: | B132 4647 |
| Деталь: | Release Lever |
| Парткод: | AG05 1141 |
| Деталь: | Lower Entrance Guide Plate |
| Парткод: | A229 4623 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B247 4817 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA08 0034 |
| Деталь: | Roller:Driven:Duplex |
| Парткод: | B247 4624 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2116 |
| Деталь: | Side Plate:Front:Reverse Unit |
| Парткод: | B132 4627 |
| Деталь: | Tension Spring:Black |
| Парткод: | AA06 2328 |
| Деталь: | Reverse Roller:Entrance |
| Парткод: | D014 4818 |
| Деталь: | Spacer:Gate Pawl |
| Парткод: | B132 4643 |
| Деталь: | Front Gate Pawl |
| Парткод: | A293 4613 |
| Деталь: | Reverse Roller |
| Парткод: | A293 4611 |
| Деталь: | Rear Gate Pawl |
| Парткод: | A293 4614 |
| Деталь: | Side Plate:Rear:Reverse Unit:Assy |
| Парткод: | B132 4620 |
| Деталь: | Joint Holder |
| Парткод: | B065 4632 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B247 4815 |
| Деталь: | Drive Joint |
| Парткод: | A229 4740 |
| Деталь: | Sensor bracket |
| Парткод: | B065 4644 |
| Деталь: | Duplex Discharge Brush |
| Парткод: | A229 4617 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0119 |
| Деталь: | Harness:Sensor:Reverse Unit:3p |
| Парткод: | D014 4985 |
| Деталь: | Guide Plate:Entrance:Upper:Assy |
| Парткод: | B132 4640 |
| Деталь: | Stopped Screw - M4x17 |
| Парткод: | AA14 3426 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Guide:Auxiliary:Reverse Roller |
| Парткод: | D014 4819 |
| Деталь: | Stepper Motor:Reverse:Assy |
| Парткод: | B132 4780 |
| Деталь: | Bracket:Motor:Reverse:Assy |
| Парткод: | B132 4810 |
| Деталь: | Gear:22/24Z |
| Парткод: | AB01 7687 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3291 |
| Деталь: | DC Solenoid:Reversal:Assy |
| Парткод: | B132 4745 |
| Деталь: | Stepper Motor:Jogger:Assy |
| Парткод: | B132 4650 |
| Деталь: | Bracket:Stepper Motor:Jogger |
| Парткод: | B132 4696 |
| Деталь: | Stepper Motor:Transport:Assy |
| Парткод: | B132 4785 |
| Деталь: | Bracket:Stepper Motor:Transport |
| Парткод: | B132 4789 |
| Деталь: | Timing Belt:40S2M360G |
| Парткод: | AA04 3309 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Lever:Roller:Driven:Reversal |
| Парткод: | B132 4663 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 2327 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Stay:Bearing:Reversal |
| Парткод: | B132 4665 |
| Деталь: | MAGNETIC |
| Парткод: | AA02 1034 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3183 |
| Деталь: | Jogger Fence:Front |
| Парткод: | B132 4681 |
| Деталь: | JOGGER FENCE:REAR |
| Парткод: | B132 4682 |
| Деталь: | Spring Plate - Rear Jogger Fence |
| Парткод: | B065 4683 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3811 |
| Деталь: | Table:Duplex:Left |
| Парткод: | B132 4720 |
| Деталь: | Arm:Roller:Reversal:Driven |
| Парткод: | B132 4661 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3592 |
| Деталь: | Roller:Reversal:Driven |
| Парткод: | AF02 0690 |
| Деталь: | Bushing - 8x10x5 |
| Парткод: | AA08 2063 |
| Деталь: | Shaft:Roller:Reversal |
| Парткод: | AA14 8692 |
| Деталь: | Bracket:Reversal:Driven:Assy |
| Парткод: | B132 4655 |
| Деталь: | Shield:Cover:Duct:Lower |
| Парткод: | B132 3227 |
| Деталь: | Duct:Development:Front |
| Парткод: | B132 2458 |
| Деталь: | Seal:Fan Motor |
| Парткод: | B132 2485 |
| Деталь: | Fan Motor:MM40:15mm |
| Парткод: | AX64 0149 |
| Деталь: | Shield:Duct |
| Парткод: | B132 2474 |
| Деталь: | Sirocco Fan Motor:DC24V 4.32W |
| Парткод: | D014 6933 |
| Деталь: | Duct:Toner Hopper:Lower |
| Парткод: | D014 6937 |
| Деталь: | Sirocco Fan Motor:DC24V 4.32W |
| Парткод: | D014 6924 |
| Деталь: | Sirocco Fan Motor:DC24V 4.32W |
| Парткод: | D014 6926 |
| Деталь: | Sirocco Fan Motor:DC24V 4.32W |
| Парткод: | D014 6928 |
| Деталь: | Duct:Toner Hopper |
| Парткод: | D014 6923 |
| Деталь: | Seal:Duct:Toner Hopper:Lower |
| Парткод: | B132 2496 |
| Деталь: | Toner Supply Unit - Drive |
| Парткод: | D014 3360 |
| Деталь: | Toner End Sensor |
| Парткод: | AW23 0024 |
| Деталь: | Coil:Guard:Tube:Color |
| Парткод: | B132 3439 |
| Деталь: | Tube:Color |
| Парткод: | B132 3437 |
| Деталь: | Coil:Guard:Tube:Black |
| Парткод: | B132 3438 |
| Деталь: | Tube:Black |
| Парткод: | B132 3436 |
| Деталь: | Cover:Lower:Toner Supply:Color |
| Парткод: | D014 6922 |
| Деталь: | Shield:Duct:Left |
| Парткод: | B132 2476 |
| Деталь: | Filter:Duct:Toner Hopper:Left |
| Парткод: | D014 6939 |
| Деталь: | Heat Insulation - Toner Supply Unit |
| Парткод: | D014 6910 |
| Деталь: | Filter:Duct:Toner Hopper:Lower |
| Парткод: | D014 6938 |
| Деталь: | Duct:Vacuum:Toner Hopper |
| Парткод: | D014 6921 |
| Деталь: | Harness:Paper Exit Unit |
| Парткод: | D014 5244 |
| Деталь: | Bracket:Sensor |
| Парткод: | B132 7049 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Cover:Exhaust |
| Парткод: | B132 7023 |
| Деталь: | Discharge Brush |
| Парткод: | AA12 0084 |
| Деталь: | Stay:Exit:Assy |
| Парткод: | B132 7018 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B247 4455 |
| Деталь: | Ball Bearing:Driven:MM4 |
| Парткод: | AA08 4053 |
| Деталь: | Exit Roller:Driven:Upper |
| Парткод: | B132 7147 |
| Деталь: | Shaft:Lever:Left Inner Rear |
| Парткод: | B132 7123 |
| Деталь: | Lever:Stopper |
| Парткод: | B132 7041 |
| Деталь: | SPRING |
| Парткод: | AA06 2319 |
| Деталь: | Lever:Open And Close |
| Парткод: | B132 7042 |
| Деталь: | Bracket:Stay:Left |
| Парткод: | B132 7119 |
| Деталь: | Bracket:Fix:Front |
| Парткод: | B132 7043 |
| Деталь: | Bracket:Drawer:Pull Out |
| Парткод: | B132 1195 |
| Деталь: | Actuator:Pull Out |
| Парткод: | B132 1194 |
| Деталь: | Cover:Base:Pull Out |
| Парткод: | B132 1220 |
| Деталь: | Harness:Pull Out:Uni:39pin |
| Парткод: | D014 5242 |
| Деталь: | Harness:High Voltage Supply Cord |
| Парткод: | B132 5356 |
| Деталь: | Power Pack:D |
| Парткод: | AZ31 0029 |
| Деталь: | Insulating Sheet:Pull Out |
| Парткод: | B132 1228 |
| Деталь: | Knob Screw |
| Парткод: | 5413 1875 |
| Деталь: | Handle:Pull Out |
| Парткод: | B132 1191 |
| Деталь: | Shaft:Lock:Pull Out |
| Парткод: | B132 1185 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3951 |
| Деталь: | Cam:Transfer Roller |
| Парткод: | B132 6305 |
| Деталь: | Toner Catchpan |
| Парткод: | B132 6285 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | A267 5814 |
| Деталь: | Holder:Spring:Pull Out |
| Парткод: | B132 1221 |
| Деталь: | Bracket:Release:Lock |
| Парткод: | B132 1190 |
| Деталь: | Roller:Lock:Pull Out |
| Парткод: | AA13 2300 |
| Деталь: | Bracket:Lock |
| Парткод: | B132 1183 |
| Деталь: | Supporting Plate:Bracket:Lock |
| Парткод: | B132 1224 |
| Деталь: | Bracket:Fix:Rear |
| Парткод: | B132 7050 |
| Деталь: | Shaft:Stopper |
| Парткод: | B132 7096 |
| Деталь: | Holder:Shaft |
| Парткод: | B132 7070 |
| Деталь: | Bracket:Interlock:Lever |
| Парткод: | B132 1193 |
| Деталь: | Guide Plate:Paper Feed:Lower |
| Парткод: | B652 2143 |
| Деталь: | Separation Cap |
| Парткод: | B477 2151 |
| Деталь: | Screw:Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Separation Support Pad |
| Парткод: | B301 1155 |
| Деталь: | Holder:Separation Pad |
| Парткод: | B652 2146 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Reverse Roller |
| Парткод: | A859 2241 |
| Деталь: | Torque Limiter - Separator |
| Парткод: | A293 6399 |
| Деталь: | Compression Spring:0.5n |
| Парткод: | B652 4156 |
| Деталь: | Bushing - 4mm |
| Парткод: | A680 1661 |
| Деталь: | Roller:Driven:Reverse:Middle |
| Парткод: | B652 4155 |
| Деталь: | Bracket:Guide Plate:Lower |
| Парткод: | B652 2127 |
| Деталь: | Reverse Roller Shaft |
| Парткод: | B477 3131 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A859 2230 |
| Деталь: | Cushion:Guide Plate:Reverse:Exit |
| Парткод: | B652 2128 |
| Деталь: | Stay:Reverse Roller:Assy |
| Парткод: | B652 2122 |
| Деталь: | Guide:Stay:Reverse Roller |
| Парткод: | B652 2126 |
| Деталь: | Guide Plate:Original Table |
| Парткод: | B652 2433 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 5053 0447 |
| Деталь: | Gate Pawl:Reverse:Upper |
| Парткод: | B652 4203 |
| Деталь: | Cushion - Bin Solenoid Lever |
| Парткод: | A458 2251 |
| Деталь: | Bracket:Discharge Brush:Assy |
| Парткод: | B652 4205 |
| Деталь: | Discharge Brush |
| Парткод: | B652 4207 |
| Деталь: | EXIT ROLLER |
| Парткод: | B652 4726 |
| Деталь: | Bracket:Sensor:Reverse:Middle |
| Парткод: | B652 4133 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Guide Plate:Reverse:Middle:Upper |
| Парткод: | B652 4122 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Hook:Solenoid:Reverse:Upper |
| Парткод: | B652 4212 |
| Деталь: | Tension Spring:Hook:Gate Pawl |
| Парткод: | B652 4213 |
| Деталь: | Timing Pulley:44t |
| Парткод: | B652 4727 |
| Деталь: | STEPPED SCREW |
| Парткод: | 5447 2769 |
| Деталь: | Paper Discharge Plate |
| Парткод: | B132 6268 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3870 |
| Деталь: | Stay:Brush Roller:Assy |
| Парткод: | B132 6253 |
| Деталь: | Stay:Transfer Unit |
| Парткод: | B132 6274 |
| Деталь: | Shaft:Contact Point |
| Парткод: | B132 6287 |
| Деталь: | Paper Transfer Roller |
| Парткод: | D014 6280 |
| Деталь: | Gear:40Z |
| Парткод: | B132 6303 |
| Деталь: | Spring:Pressure |
| Парткод: | B132 6306 |
| Деталь: | PTR Cleaning Brush |
| Парткод: | B132 6255 |
| Деталь: | Bushing:6x10x6 |
| Парткод: | AA08 2137 |
| Деталь: | Guide Plate:Entrance:Assy |
| Парткод: | B132 6295 |
| Деталь: | Brush Roller:Apply |
| Парткод: | D014 6268 |
| Деталь: | PTR Lubricant Bar |
| Парткод: | D014 6260 |
| Деталь: | PTR Cleaning Blade |
| Парткод: | D014 6265 |
| Деталь: | Holder:Blade |
| Парткод: | B132 6269 |
| Деталь: | Spring:Blade |
| Парткод: | B132 6299 |
| Деталь: | Gear:40Z |
| Парткод: | B132 6301 |
| Деталь: | Joint:Transfer:Drive |
| Парткод: | B132 6284 |
| Деталь: | Gear:40Z |
| Парткод: | B132 6302 |
| Деталь: | Bracket:Gear:Idler |
| Парткод: | B132 6311 |
| Деталь: | Base:Transfer Roller:Rear:Assy |
| Парткод: | B132 6307 |
| Деталь: | Spring:Pressure |
| Парткод: | B132 6288 |
| Деталь: | Gear:21Z |
| Парткод: | AB01 1124 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Timing Belt:S2M170 |
| Парткод: | AA04 3587 |
| Деталь: | Pulley:23T |
| Парткод: | AB03 0749 |
| Деталь: | Supporting Plate:Pull Out |
| Парткод: | B132 1186 |
| Деталь: | Gear:20/29Z |
| Парткод: | AB01 1125 |
| Деталь: | Gear:20Z |
| Парткод: | AB01 1126 |
| Деталь: | Basefront |
| Парткод: | B132 6314 |
| Деталь: | Rear bushing |
| Парткод: | AA08 0154 |
| Деталь: | Spring:Tightener:Transport Screw |
| Парткод: | B132 6337 |
| Деталь: | Pulley:Belt Tensioner |
| Парткод: | A257 6112 |
| Деталь: | Tightener:Transfer:Transport Screw:Assy |
| Парткод: | B132 6331 |
| Деталь: | Side Plate:Positioning:Transfer:Front:Assy |
| Парткод: | B132 6334 |
| Деталь: | Bushing:Brush:Rear |
| Парткод: | D014 6272 |
| Деталь: | Seal:Side Plate:Rear |
| Парткод: | B132 6326 |
| Деталь: | Seal:Side Plate:Front |
| Парткод: | B132 6325 |
| Деталь: | Gear:16z |
| Парткод: | D014 6273 |
| Деталь: | Belt Cleaning Unit |
| Парткод: | D014 6400 |
| Деталь: | Duct:Belt Cleaning:Side:Assy |
| Парткод: | D014 6951 |
| Деталь: | Roller:Pressure |
| Парткод: | B132 6469 |
| Деталь: | Spring:Blade:Apply |
| Парткод: | D014 6489 |
| Деталь: | Holder:Belt Cleaning Unit |
| Парткод: | D014 6486 |
| Деталь: | Lubricant Supply Blade |
| Парткод: | D014 6507 |
| Деталь: | Lubricant Supply Brush |
| Парткод: | D014 6463 |
| Деталь: | Shield:Holder:Blade:Front Upper |
| Парткод: | D014 6517 |
| Деталь: | Shield:Holder:Blade:Front Lower |
| Парткод: | D014 6518 |
| Деталь: | Shield:Holder:Blade:Rear Upper |
| Парткод: | D014 6522 |
| Деталь: | Shield:Holder:Blade:Rear Lower |
| Парткод: | D014 6523 |
| Деталь: | Spring:Blade:No.1 |
| Парткод: | D014 6458 |
| Деталь: | Holder:Blade:Belt Cleaning Unit |
| Парткод: | D014 6466 |
| Деталь: | Belt Cleaning Blade |
| Парткод: | D014 6455 |
| Деталь: | Stay:Roller:Pressure:Rear |
| Парткод: | D014 6529 |
| Деталь: | Holder:Spring:Roller:Pressure |
| Парткод: | B132 6459 |
| Деталь: | Spring:Roller:Pressure |
| Парткод: | D014 6478 |
| Деталь: | Case:Spring:Roller:Pressure |
| Парткод: | B132 6460 |
| Деталь: | Pin:Positioning:Blade |
| Парткод: | D014 6510 |
| Деталь: | Bushing:Dia6:Dia8 |
| Парткод: | AA08 3022 |
| Деталь: | Shield:Case:Brush:Front |
| Парткод: | D014 6521 |
| Деталь: | Gear:12Z/21Z |
| Парткод: | D014 6483 |
| Деталь: | Gear:19Z |
| Парткод: | D014 6485 |
| Деталь: | Gear:18Z |
| Парткод: | D014 6481 |
| Деталь: | Snap Ring |
| Парткод: | G011 1058 |
| Деталь: | Stay:Roller:Pressure:Front |
| Парткод: | D014 6528 |
| Деталь: | Belt Cleaning Lubricant Bar |
| Парткод: | D014 6470 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 5206 2684 |
| Деталь: | Guide Plate - Paper Exit Unit |
| Парткод: | D014 4127 |
| Деталь: | Grip:Oil Application Unit:Fiber |
| Парткод: | B132 4167 |
| Деталь: | Front Lever - Paper Exit Unit |
| Парткод: | D014 4155 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Bracket - Exit Unit |
| Парткод: | D014 4150 |
| Деталь: | Shaft:Oil Application Unit |
| Парткод: | B132 4163 |
| Деталь: | TORSION SPRING:LEVER |
| Парткод: | B132 4197 |
| Деталь: | Rear Lever - Paper Exit Unit |
| Парткод: | D014 4156 |
| Деталь: | Tension Spring - Stripper Plate |
| Парткод: | AA06 1019 |
| Деталь: | Front Lever - Stripper Plate |
| Парткод: | D014 4324 |
| Деталь: | Front Bracket - Stripper Plate |
| Парткод: | D014 4151 |
| Деталь: | Front Torsion Spring - Stripper |
| Парткод: | AA06 6382 |
| Деталь: | Stay - Bracket |
| Парткод: | D014 4307 |
| Деталь: | Stripper Plate Unit |
| Парткод: | D014 4300 |
| Деталь: | Rear Torsion Spring - Stripper |
| Парткод: | AA06 6383 |
| Деталь: | Rear Bracket - Stripper Plate |
| Парткод: | D014 4154 |
| Деталь: | Rear Lever - Stripper Plate |
| Парткод: | D014 4325 |
| Деталь: | Upper Guide Plate - Fusing Exit |
| Парткод: | D014 4158 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 1018 |
| Деталь: | Roller Holder - Fusing Exit |
| Парткод: | D014 4167 |
| Деталь: | Roller - Fusing Exit |
| Парткод: | D014 4327 |
| Деталь: | Torsion Spring - Front |
| Парткод: | AA06 6682 |
| Деталь: | Bracket:Torsion Spring:Peen |
| Парткод: | B132 4127 |
| Деталь: | Spring Bracket - Separation |
| Парткод: | D014 4148 |
| Деталь: | Torsion Spring - Rear |
| Парткод: | AA06 6683 |
| Деталь: | Duplex Gate Pawl |
| Парткод: | B065 4733 |
| Деталь: | Gate Pawl Cushion |
| Парткод: | B065 4738 |
| Деталь: | Lower Duplex Guide Plate |
| Парткод: | A294 4626 |
| Деталь: | SPACER |
| Парткод: | B065 4865 |
| Деталь: | Stay:Timing Belt |
| Парткод: | B132 4689 |
| Деталь: | Timing Belt - 40S2M810G |
| Парткод: | AA04 3294 |
| Деталь: | Slider:Jogger Fence:Front |
| Парткод: | B132 4692 |
| Деталь: | Slider:Jogger Fence:Rear |
| Парткод: | B132 4693 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0148 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0149 |
| Деталь: | Bracket:Sensor:Reverse:Exit |
| Парткод: | B132 4715 |
| Деталь: | Gear - 30Z/45Z |
| Парткод: | AB01 7615 |
| Деталь: | Guide Plate:Transport:Upper:Assy |
| Парткод: | B132 4710 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0984 |
| Деталь: | DC Solenoid:Gate Pawl |
| Парткод: | D014 4740 |
| Деталь: | Duplex Guide |
| Парткод: | A096 4595 |
| Деталь: | Bracket:Support:Positioning Pin |
| Парткод: | B132 4619 |
| Деталь: | Bracket:Drawer:32pin |
| Парткод: | D014 4790 |
| Деталь: | Harness:Duplex Unit:32Pin |
| Парткод: | D014 5261 |
| Деталь: | Bracket:Drawer:12pin:Duplex |
| Парткод: | B132 4791 |
| Деталь: | Harness:Duplex Unit:12pin |
| Парткод: | D014 5262 |
| Деталь: | Jogger Pulley |
| Парткод: | AB03 0732 |
| Деталь: | SPRING |
| Парткод: | AA06 2318 |
| Деталь: | Jogger Bracket |
| Парткод: | B065 4820 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Bracket:Home Position Sensor:Jogger |
| Парткод: | B132 4699 |
| Деталь: | Gear - 32Z |
| Парткод: | AB01 4291 |
| Деталь: | Ball Bearing -20x32x7 |
| Парткод: | AE03 0049 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AE02 0165 |
| Деталь: | Holder:Adjusting Pin:M5 |
| Парткод: | D014 4291 |
| Деталь: | Lever:Control Plate:Pressure:Link:Peen |
| Парткод: | D014 4292 |
| Деталь: | Lever:Control Plate:Pressure |
| Парткод: | D014 4289 |
| Деталь: | Stepped Screw - M5 |
| Парткод: | D014 4296 |
| Деталь: | Upper Front Lever - Pressure |
| Парткод: | D014 4281 |
| Деталь: | Compression Spring - Pressure |
| Парткод: | AA06 3450 |
| Деталь: | Hub:Pressure Stand:M5 |
| Парткод: | D014 4290 |
| Деталь: | Pin:Lever:Pressure:Control Plate |
| Парткод: | D014 4287 |
| Деталь: | Lever:Pressure:Lower Front:Assy |
| Парткод: | D014 4284 |
| Деталь: | Pin:Cam:Lever:Pressure |
| Парткод: | D014 4233 |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | AE03 0056 |
| Деталь: | Front Lock Bracket - Fusing Unit |
| Парткод: | D014 4269 |
| Деталь: | Side Plate - Lower Front |
| Парткод: | D014 4201 |
| Деталь: | Stay - Lower |
| Парткод: | D014 4203 |
| Деталь: | Stay - Right Lower |
| Парткод: | D014 4204 |
| Деталь: | AC/DC Harness - Fusing Unit 120V |
| Парткод: | D014 5204 |
| Деталь: | AC/DC Harness - Fusing Unit 230V |
| Парткод: | D014 5209 |
| Деталь: | Side Plate - Lower Rear |
| Парткод: | D014 4202 |
| Деталь: | Rear Lock Bracket - Fusing Unit |
| Парткод: | D014 4271 |
| Деталь: | Lever:Pressure:Lower Rear:Assy |
| Парткод: | D014 4225 |
| Деталь: | Bracket - Drawer |
| Парткод: | D014 4241 |
| Деталь: | Terminal:4P:187 |
| Парткод: | AA11 3037 |
| Деталь: | Upper Rear Lever - Pressure |
| Парткод: | D014 4282 |
| Деталь: | Idle Gear - 27Z |
| Парткод: | AB01 4322 |
| Деталь: | Manual Paper Feed Unit |
| Парткод: | D014 2800 |
| Деталь: | Cover:Manual Feed Unit |
| Парткод: | B132 2859 |
| Деталь: | Holder:Manual Feed Table:Front |
| Парткод: | B132 2819 |
| Деталь: | Harness:Manual Paper Feed Unit |
| Парткод: | D014 5249 |
| Деталь: | Feeler:Paper End Sensor |
| Парткод: | B132 2845 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Feeler Roller |
| Парткод: | A134 2661 |
| Деталь: | Bracket:Sensor:Manual Feed |
| Парткод: | B132 2848 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0952 |
| Деталь: | DC Solenoid:Pickup:Assy |
| Парткод: | B132 2839 |
| Деталь: | One-way Clutch |
| Парткод: | AA08 3014 |
| Деталь: | Gear:42z |
| Парткод: | AB01 1307 |
| Деталь: | Roller:Manual Feed Unit:Drive |
| Парткод: | B132 2856 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Stopper:Magnetic Clutch |
| Парткод: | B132 2857 |
| Деталь: | Holder:Manual Feed Table:Rear |
| Парткод: | B132 2823 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Paper Feed Roller:Feed:Manual Feed |
| Парткод: | AF03 1081 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2116 |
| Деталь: | Gear - 15T |
| Парткод: | 5447 2706 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF03 0080 |
| Деталь: | Guide Plate:Feed |
| Парткод: | B132 2837 |
| Деталь: | Ground Plate:Manual Feed |
| Парткод: | B132 2846 |
| Деталь: | Arm:Pickup:Manual Feed |
| Парткод: | B132 2835 |
| Деталь: | Shaft:Feed Roller |
| Парткод: | AA14 0761 |
| Деталь: | Bushing - 8x18x11 |
| Парткод: | AA08 3013 |
| Деталь: | Magnetic Clutch:0.53N M:36Z |
| Парткод: | AX20 0277 |
| Деталь: | Guide Plate:Separator:Adhesion |
| Парткод: | D014 2825 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3016 |
| Деталь: | Shaft:Separator:Drive:Assy |
| Парткод: | B132 2849 |
| Деталь: | Gear:24Z |
| Парткод: | AB01 1306 |
| Деталь: | Paper Feed Roller:Separate |
| Парткод: | AF03 2080 |
| Деталь: | Torque Limiter - 53mnxm |
| Парткод: | A294 6700 |
| Деталь: | Shaft:Separator:Driven:Assy |
| Парткод: | B132 2851 |
| Деталь: | Gear:21Z |
| Парткод: | AB01 1305 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0954 |
| Деталь: | Lever:Pressure:Separator |
| Парткод: | B132 2853 |
| Деталь: | Paper Tray:Universal:DOM:Assy |
| Парткод: | D014 6771 |
| Деталь: | Link:Side Fence:Paper Size Sensor |
| Парткод: | B181 6789 |
| Деталь: | Link:End Fence:Paper Size Sensor:Assy |
| Парткод: | B181 6780 |
| Деталь: | Side Fence:Front:Assy |
| Парткод: | B132 6793 |
| Деталь: | Positioning Stopper Lever |
| Парткод: | B065 6538 |
| Деталь: | Spring Plate |
| Парткод: | A134 2978 |
| Деталь: | Plate:Side Fence |
| Парткод: | B132 6791 |
| Деталь: | Side Fence Pad |
| Парткод: | A096 6553 |
| Деталь: | Tray Bottom Plate:Assy |
| Парткод: | D014 6780 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3005 |
| Деталь: | Side Fence:Rear:Assy |
| Парткод: | B132 6795 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A267 2860 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA00 2010 |
| Деталь: | Spring Plate:Paper Tray:Earth |
| Парткод: | B132 6798 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | D014 6786 |
| Деталь: | Decal - Positioning |
| Парткод: | B065 6545 |
| Деталь: | Arm:End Fence:Lock |
| Парткод: | D014 6783 |
| Деталь: | END FENCE |
| Парткод: | AF01 7033 |
| Деталь: | Side Fence:Rear:Auxiliary |
| Парткод: | B132 6797 |
| Деталь: | Gear:16z |
| Парткод: | AB01 2327 |
| Деталь: | Misfeed Removal Guide |
| Парткод: | A176 6695 |
| Деталь: | Tension Spring:Side Fence:Rear |
| Парткод: | AA06 0961 |
| Деталь: | Bottom Plate Lift Shaft |
| Парткод: | B065 6524 |
| Деталь: | Lift Lever |
| Парткод: | B065 6526 |
| Деталь: | Spring Plate:End Fence |
| Парткод: | D014 6784 |
| Деталь: | Spring Plate:Arm:End Fence:Lock |
| Парткод: | D014 6785 |
| Деталь: | Tension Spring:Lock:Lever |
| Парткод: | B652 3145 |
| Деталь: | Hook:Lock:Image Reading Unit:Front |
| Парткод: | B652 3148 |
| Деталь: | Shaft:Lever:Misfeed Removal:Assy |
| Парткод: | B652 3146 |
| Деталь: | Transport Belt |
| Парткод: | B652 3121 |
| Деталь: | Roller:Transport Belt:Drive |
| Парткод: | B652 3112 |
| Деталь: | Stopper:Roller:Drive |
| Парткод: | B652 3119 |
| Деталь: | Discharge Brush:Short |
| Парткод: | B652 3158 |
| Деталь: | Discharge Brush:Long |
| Парткод: | B652 3157 |
| Деталь: | Discharge Brush:Middle |
| Парткод: | B652 3159 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B477 2621 |
| Деталь: | Guide:Transport Belt:Front |
| Парткод: | B652 3116 |
| Деталь: | Housing:Transport Belt Unit |
| Парткод: | B652 3120 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 3125 |
| Деталь: | Guide:Transport Belt:Rear |
| Парткод: | B652 3117 |
| Деталь: | Spacer:Transport Belt |
| Парткод: | B652 3156 |
| Деталь: | Roller:Pressure |
| Парткод: | B652 3113 |
| Деталь: | Bracket:Roller:Driven |
| Парткод: | B652 3123 |
| Деталь: | Driven Roller:Scanning |
| Парткод: | B652 3124 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | DC Solenoid:Reverse:Lower:Assy |
| Парткод: | B652 4766 |
| Деталь: | Lever:Reverse:Lower:DC Solenoid |
| Парткод: | B652 4532 |
| Деталь: | Bracket:Reverse:Lower:DC Solenoid |
| Парткод: | B652 4533 |
| Деталь: | Damper - Junction Gate Solenoid |
| Парткод: | A697 2102 |
| Деталь: | Transport Belt Unit:Assy |
| Парткод: | B652 0331 |
| Деталь: | Bracket:Connector:Right |
| Парткод: | B132 6764 |
| Деталь: | DC Harness - Bank Rear |
| Парткод: | D014 5396 |
| Деталь: | Connector Spring |
| Парткод: | AA06 3268 |
| Деталь: | Bracket:Arm:Assy |
| Парткод: | B132 6726 |
| Деталь: | Bracket:Connector:Left |
| Парткод: | B132 6763 |
| Деталь: | LOCK ARM |
| Парткод: | B065 6769 |
| Деталь: | Lock Spring - Large |
| Парткод: | B247 6753 |
| Деталь: | DC Motor:Rise:Tandem LCT:Assy |
| Парткод: | B132 6759 |
| Деталь: | Lock Spring - Small |
| Парткод: | B247 6754 |
| Деталь: | DC Solenoid:Coupling:Assy |
| Парткод: | B132 6762 |
| Деталь: | DC Solenoid:Lock:Assy |
| Парткод: | B132 6765 |
| Деталь: | Spring:Connector:Tandem LCT |
| Парткод: | AA06 3902 |
| Деталь: | Spacer - 6mm |
| Парткод: | AA13 2203 |
| Деталь: | Imaging Unit |
| Парткод: | D014 1950 |
| Деталь: | Cable:LVDS:LDB |
| Парткод: | D014 5367 |
| Деталь: | Grip:Imaging Unit |
| Парткод: | B132 1972 |
| Деталь: | Decal - LD 655 |
| Парткод: | AA00 0217 |
| Деталь: | Cover:Polygon Motor:Assy |
| Парткод: | B132 2185 |
| Деталь: | Polygon Mirror Motor |
| Парткод: | D014 2157 |
| Деталь: | Positioning Pin |
| Парткод: | B132 1971 |
| Деталь: | Harness:Connecting:LDB:LDD |
| Парткод: | D014 5366 |
| Деталь: | Cover:Upper:Sub-assy |
| Парткод: | B132 2172 |
| Деталь: | Harness:Imaging Unit |
| Парткод: | D014 5226 |
| Деталь: | Shield:Shield Glass |
| Парткод: | B132 2085 |
| Деталь: | Grip:Shield Glass |
| Парткод: | B132 2094 |
| Деталь: | Shield Glass |
| Парткод: | AC01 5041 |
| Деталь: | Rail:Shield Glass |
| Парткод: | B132 2093 |
| Деталь: | Thermistor Plate |
| Парткод: | G060 1908 |
| Деталь: | Thermistor:Imaging Unit |
| Парткод: | AW10 0100 |
| Деталь: | Exit Roller:Exit:Drive |
| Парткод: | B132 7086 |
| Деталь: | Roller:Middle |
| Парткод: | D014 7082 |
| Деталь: | Guide Plate:Shaft:Assy |
| Парткод: | B132 7151 |
| Деталь: | Spacer:DIA21 |
| Парткод: | B132 7165 |
| Деталь: | Spring Washer - BD10 |
| Парткод: | 5937 4158 |
| Деталь: | Roller:Decura |
| Парткод: | D014 7156 |
| Деталь: | Roller:Decura:Exit |
| Парткод: | B132 7085 |
| Деталь: | Washer M6 - Scanner Unit |
| Парткод: | H053 1174 |
| Деталь: | Spring - Lower Exit Roller |
| Парткод: | B247 4456 |
| Деталь: | Shift Clutch |
| Парткод: | A470 1703 |
| Деталь: | Pulley:19Z |
| Парткод: | B132 7051 |
| Деталь: | Timing Belt:T198 |
| Парткод: | B132 7116 |
| Деталь: | Tightener:Front Upper:Assy |
| Парткод: | B132 7112 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0695 |
| Деталь: | Pulley:13T |
| Парткод: | B132 7048 |
| Деталь: | Roller:Tightener |
| Парткод: | B132 7025 |
| Деталь: | Bracket:Connector |
| Парткод: | B132 7069 |
| Деталь: | Pulley:15T |
| Парткод: | B132 7036 |
| Деталь: | Pulley:15T |
| Парткод: | B132 7028 |
| Деталь: | Timing Belt:T213 |
| Парткод: | B132 7117 |
| Деталь: | Roller:Tightener |
| Парткод: | B132 7059 |
| Деталь: | Shaft:Base:Tightener |
| Парткод: | B132 7141 |
| Деталь: | Pulley:37T |
| Парткод: | B132 7080 |
| Деталь: | Spring:Tightener |
| Парткод: | B132 7143 |
| Деталь: | Gear:Z20 |
| Парткод: | B132 7138 |
| Деталь: | Gear:Z28 |
| Парткод: | B132 7144 |
| Деталь: | Pulley:Z13 |
| Парткод: | B132 7162 |
| Деталь: | Gear:Z27 |
| Парткод: | B132 7030 |
| Деталь: | Gear:29Z |
| Парткод: | B132 7060 |
| Деталь: | Gear:22Z |
| Парткод: | B132 7055 |
| Деталь: | Stopper:Guide |
| Парткод: | B132 7155 |
| Деталь: | Harness:Connecting:Main:Thermistor |
| Парткод: | D014 5264 |
| Деталь: | THERMISTOR |
| Парткод: | AW10 0107 |
| Деталь: | Cover:Discharge Used Toner |
| Парткод: | D014 3240 |
| Деталь: | Seal:Discharge Used Toner |
| Парткод: | D014 3241 |
| Деталь: | Seal:Discharge Used Toner:Lower |
| Парткод: | D014 3242 |
| Деталь: | Toner Outlet Unit:PCU |
| Парткод: | D014 6558 |
| Деталь: | Duct:PCU:Side Plate:Main |
| Парткод: | D014 3624 |
| Деталь: | Toner Catchpan:K |
| Парткод: | B132 6599 |
| Деталь: | Cover:Drawer |
| Парткод: | B132 1229 |
| Деталь: | Duct:Stay:Right |
| Парткод: | D014 3613 |
| Деталь: | Toner Outlet Unit:Transfer Belt |
| Парткод: | D014 6569 |
| Деталь: | Duct:Charge Corona:Side |
| Парткод: | D014 3616 |
| Деталь: | Duct Filter - Charge Corona |
| Парткод: | D014 3664 |
| Деталь: | Cover:Duct:Blower:Charge Corona |
| Парткод: | D014 3611 |
| Деталь: | Sirocco Fan Motor:DC24V 1.44W |
| Парткод: | D014 3607 |
| Деталь: | Harness:Sirocco Fan Motor |
| Парткод: | D014 5385 |
| Деталь: | Duct:Blower:Charge Corona |
| Парткод: | D014 3610 |
| Деталь: | Toner Outlet Sub-Unit:PCU: Lengthwise:Assy |
| Парткод: | B132 6528 |
| Деталь: | Pipe:Toner Recycling Section: Around The Photo |
| Парткод: | B132 6531 |
| Деталь: | Transport Screw:Lengthwise |
| Парткод: | B132 6561 |
| Деталь: | Shaft:Drive:Short:Assy |
| Парткод: | B132 6545 |
| Деталь: | Case:Drive:Assy |
| Парткод: | B132 6540 |
| Деталь: | Gear:26Z |
| Парткод: | AB01 3122 |
| Деталь: | Gear:30Z |
| Парткод: | AB01 3189 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Stud:Manual Feed:Rear |
| Парткод: | D014 1127 |
| Деталь: | Guide:Paper Feed:Upper |
| Парткод: | B477 2342 |
| Деталь: | Decal:Misfeed Removal:Paper Feed |
| Парткод: | B652 1811 |
| Деталь: | Decal:Display Guidance |
| Парткод: | B652 1812 |
| Деталь: | Decal:Size:Original |
| Парткод: | B652 1807 |
| Деталь: | Paper Feed Cover Grip |
| Парткод: | B477 1821 |
| Деталь: | Paper Feed Release Lever |
| Парткод: | B477 1825 |
| Деталь: | SPRING |
| Парткод: | B477 4117 |
| Деталь: | Grip Shaft |
| Парткод: | B477 1831 |
| Деталь: | Bracket:Pressure:Pickup |
| Парткод: | B652 1822 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 1824 |
| Деталь: | Pressure Plate:Pickup |
| Парткод: | B652 1823 |
| Деталь: | Rear Cover Bracket |
| Парткод: | B477 1851 |
| Деталь: | Front Cover Bracket |
| Парткод: | B477 1841 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Paper feed Cover |
| Парткод: | B477 1791 |
| Деталь: | Bracket:Pressure:Pull Out:Assy |
| Парткод: | B652 2362 |
| Деталь: | Discharge Brush:Exit:L45 |
| Парткод: | B652 2516 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0037 |
| Деталь: | SPRING |
| Парткод: | B477 4111 |
| Деталь: | Driven Pull Out Roller |
| Парткод: | B477 2351 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | A697 2131 |
| Деталь: | Bracket:Paper Size Sensor |
| Парткод: | B652 2523 |
| Деталь: | Photointerruptor:Paper Size Sensor |
| Парткод: | AW02 0155 |
| Деталь: | PHOTOINTERRUPTOR:ENTRANCE |
| Парткод: | AW02 0154 |
| Деталь: | Harness:Sensor:Connecting: Paper Size Sensor |
| Парткод: | B652 5412 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Harness:Sensor:Connecting:Stopper Guide |
| Парткод: | B652 5418 |
| Деталь: | Relay Roller Arm |
| Парткод: | B477 2373 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 2505 |
| Деталь: | Driven Paper Feed Roller |
| Парткод: | B477 2372 |
| Деталь: | Link:Stopper:Cover:Paper Feed |
| Парткод: | B652 1816 |
| Деталь: | Tapping Screw:M3x6 |
| Парткод: | AA14 3846 |
| Деталь: | Duct:Vacuum Unit |
| Парткод: | D014 6942 |
| Деталь: | Sirocco Fan Motor:DC24C 4.32W |
| Парткод: | AX64 0193 |
| Деталь: | Seal:Sirocco Fan Motor |
| Парткод: | D014 6930 |
| Деталь: | Filter:Bracket:Vacuum:Belt Cleaning |
| Парткод: | D014 6948 |
| Деталь: | Plate:Lever:Drum Stay:Left |
| Парткод: | D014 1248 |
| Деталь: | Lever:Drum Stay:Left |
| Парткод: | B132 2366 |
| Деталь: | Duct:Development |
| Парткод: | D014 6901 |
| Деталь: | Duct:Drum Stay:PCU |
| Парткод: | D014 3659 |
| Деталь: | Duct:Drum Stay |
| Парткод: | B132 2442 |
| Деталь: | Shield:Duct:Intermediate Transfer |
| Парткод: | B132 2450 |
| Деталь: | Side Plate Lever |
| Парткод: | A257 3441 |
| Деталь: | Drum Stay Unit |
| Парткод: | D014 1242 |
| Деталь: | Decal:Development Unit:Display:Y |
| Парткод: | GA00 3020 |
| Деталь: | Decal:Development Unit:Display:C |
| Парткод: | GA00 3022 |
| Деталь: | Decal:Development Unit:Display:M |
| Парткод: | GA00 3021 |
| Деталь: | Decal:Development Unit:Display:K |
| Парткод: | GA00 3023 |
| Деталь: | Decal - Release Lever |
| Парткод: | B065 3699 |
| Деталь: | Seal:Drum Stay:Lower |
| Парткод: | B132 2417 |
| Деталь: | Heat Insulation:Drum Stay |
| Парткод: | B132 4326 |
| Деталь: | Duct:Development:Black |
| Парткод: | D014 6904 |
| Деталь: | Inner Cover:Drum Stay |
| Парткод: | D014 6949 |
| Деталь: | Shield:Duct:Inner Cover |
| Парткод: | D014 6971 |
| Деталь: | Duct:Development:Fc |
| Парткод: | D014 6907 |
| Деталь: | Harness:Fan |
| Парткод: | D014 5232 |
| Деталь: | Fan Motor:MM40:15mm |
| Парткод: | AX64 0149 |
| Деталь: | Duct:Intermediate Transfer |
| Парткод: | B132 2454 |
| Деталь: | Filter:Duct:Intermediate Transfer |
| Парткод: | B132 2466 |
Коды ошибок
SC101
SC120
SC121
SC141
SC142
SC143
SC144
SC161
SC165
SC180
SC181
SC182
SC195
SC202
SC203
SC204
SC210
SC211
SC212
SC213
SC220
SC221
SC222
SC223
SC224
SC225
SC226
SC227
SC230
SC231
SC232
SC233
SC234
SC235
SC236
SC237
SC240
SC241
SC242
SC243
SC268
SC270
SC271
SC272
SC285
SC300
SC301
SC302
SC303
SC304
SC308
SC313
SC314
SC315
SC316
SC317
SC318
SC319
SC320
SC321
SC322
SC323
SC324
SC325
SC326
SC327
SC336
SC337
SC338
SC339
SC348
SC350
SC351
SC352
SC353
SC360
SC361
SC362
SC363
SC364
SC365
SC366
SC367
SC372
SC373
SC374
SC375
SC396
SC397
SC398
SC399
SC400
SC410
SC411
SC412
SC413
SC414
SC415
SC416
SC417
SC418
SC420
SC421
SC422
SC423
SC424
SC425
SC426
SC427
SC432
SC433
SC434
SC435
SC436
SC437
SC438
SC439
SC440
SC441
SC442
SC443
SC445
SC446
SC447
SC450
SC452
SC455
SC460
SC465
SC466
SC467
SC468
SC472
SC480
SC481
SC482
SC483
SC484
SC485
SC487
SC488
SC490
SC495
SC496
SC497
SC498
SC499
SC501
SC502
SC503
SC504
SC505
SC510
SC515
SC516
SC517
SC518
SC530
SC531
SC532
SC533
SC534
SC535
SC536
SC537
SC538
SC539
SC540
SC541
SC543
SC544
SC545
SC546
SC547
SC549
SC550
SC551
SC552
SC553
SC554
SC555
SC556
SC557
SC559
SC561
SC562
SC563
SC564
SC565
SC568
SC569
SC570
SC571
SC572
SC573
SC574
SC599
SC620
SC621
SC622
SC624
SC625
SC626
SC627
SC687
SC701
SC705
SC720
SC721
SC723
SC724
SC725
SC726
SC727
SC728
SC730
SC731
SC732
SC733
SC734
SC735
SC736
SC737
SC738
SC740
SC741
SC742
SC743
SC744
SC745
SC746
SC747
SC748
SC750
SC753
SC754
SC755
SC760
SC761
SC763
SC764
SC765
SC766
SC767
SC770
SC771
SC772
SC773
SC775
SC776
SC780
SC781
SC782
SC784
SC785
SC786
SC817
SC819
SC821
SC822
SC824
SC829
SC833
SC834
SC850
SC858
SC859
SC861
SC863
SC864
SC865
SC867
SC868
SC870
SC874
SC875
SC901
SC902
SC910 … C914
SC919
SC925
Описание
| Error code: | SC101 |
| Description: | Exposure lamp error The white level peak did not reach the prescribed threshold when the white plate was scanned. |
| Causes: | The scanner has scanned the white plate, but cannot detect the certain white level. • Defective exposure lamp • Defective exposure lamp stabilizer • Defective power source harness • Defective signal harness • High-voltage cable leak • Defective darkness starting characteristic |
| Remedy: | • Dirty optics • Exposure lamp defective • Exposure lamp does not turn ON • Lamp stabilizer defective • High voltage line leak • Power/signal harness defective |
| Error code: | SC120 |
| Description: | Scanner home position error 1 The scanner home position sensor did not detect the home position (did not go OFF) after the scanner moved forward 20 mm.. |
| Causes: | The scanner home position sensor does not detect the scanner leaving the home position. • Defective scanner home position sensor • Defective scanner home position sensor harness • Defective scanner motor driver • Defective scanner motor |
| Remedy: | • Scanner motor driver board defective • Scanner motor defective • Scanner HP sensor defective • Harness between scanner motor and scanner I/O board disconnected or broken. |
| Error code: | SC121 |
| Description: | Scanner home position error 2 The scanner home position sensor did not go ON after the scanner moved forward 1 mm and the feeler entered the HP sensor. |
| Causes: | The scanner home position sensor does not detect the scanner coming back to the home position. • Defective scanner home position sensor • Defective scanner home position sensor harness • Defective scanner motor driver • Defective scanner motor |
| Remedy: | • Scanner motor defective • Scanner HP sensor disconnected, defective |
| Error code: | SC141 |
| Description: | Black level detection error During AGC the value for black level was not within ±2 of the prescribed value. The copier can reproduce monochrome, but not color. |
| Causes: | The automatic adjustment has failed to correct the black level to the permissible range. • Defective SBU board • Defective harness |
| Remedy: | • SBU defective • Harness defective |
| Error code: | SC142 |
| Description: | White level detection error During AGC the value for white level was not within ±7 of the prescribed value. |
| Causes: | The automatic adjustment has failed to correct the white level to the permissible range. • Defective scanner drive • Defective optical section • Defective SBU board • Defective harness |
| Remedy: | • Exposure lamp defective • Harness disconnected, damaged • Dirty exposure glass, optics • Scanner motor, drive assembly defective • SBU board defective |
| Error code: | SC143 |
| Description: | SBU Auto Adjust Error At power on the automatic white level adjustment failed. |
| Causes: | • Clean the white plate • Clean the optics and lenses • Check the connectors between the SBU and IPU. • Replace the SBU • Replace the IPU • Replace the VBCU • Replace the exposure lamp |
| Error code: | SC144 |
| Description: | SBU (Sensor Board Unit) communication error When the machine is switched ON, or when the machine returns to full operation from the energy save mode, the machine can not access the SBU register, or the SBU register values are abnormal. |
| Causes: | Cannot correctly establish communication with the SBU. • Defective harness • Defective destination device (e.g., BICU, etc) • Defective SBU |
| Remedy: | • Dirty exposure glass or optics • SBU board defective • SBU harness disconnected, defective |
| Error code: | SC161 |
| Description: | IDU (Image Discrimination Unit) error After the command is written into the DFID self-diagnosis startup register, the correct value is not stored in the register for the prescribed length of time after power ON. -or- After the negate interruption of FGATE occurs, IDU is not recognized within the prescribed time during scanning. |
| Causes: | • Check harness connections between SBU and IPU/VBCU • IPU defective • VBCU defective |
| Remedy: | • IPU board defective (defective connection between ASIC and DFID, defective LSYNC-signal) |
| Error code: | SC165 |
| Description: | Unauthorized copy protection failed |
| Causes: | • The machine detects that the optional ICIB is not installed or is faulty even if "Unauthorized Copy Protection" in User Tools is enabled. • When the machine is switched on or recovers from the evergy saver mode, it detects that the installed optional ICIB is faulty. • ICIB nlot attached correctly • Defective ICIB |
| Remedy: | • Connect the ICIB correctly • Replace the ICIB |
| Error code: | SC180 |
| Description: | Scanner Unit Exhaust Fan Lock The scanner unit exhaust fan did not switch on within 10 sec. after the CPU issued the ON signal. |
| Causes: | • Foreign object interfering with operation of fan • Fan motor harness disconnected or defective • Fan defective • SIOB board defective • SBU board defective |
| Error code: | SC181 |
| Description: | Lamp Regulator Cooling Fan The fan next to the lamp regulator board did not switch on within 10 sec. after the CPU issued the ON signal. |
| Causes: | • Fan motor harness disconnected or defective • SBU harness disconnected or defective • SIOB harness disconnected or defective • Fan defective • SBU board defective • SIOB board defective |
| Error code: | SC182 |
| Description: | Scanner Unit Exhaust Fan Lock The scanner unit exhaust fan did not switch on within 10 sec. after the CPU issued the ON signal. |
| Causes: | • Fan motor harness disconnected or defective • SBU harness disconnected or defective • SIOB harness disconnected or defective • Fan defective • SBU board defective • SIOB board defective |
| Error code: | SC195 |
| Description: | Machine serial number error The number registered for the machine serial number does not match. |
| Causes: | Comparison of the product identification code in the machine serial number (11 digits). The product identification code in the machine serial number (11 digits) does not match. |
| Remedy: | • Confirm the correct serial number of the machine in the specifications Important! WHEN SC195 OCCURS, THE SERIAL NUMBER MUST BE INPUT. PLEASE CONTACT YOUR TECHNICAL SUPERVISOR. |
| Error code: | SC202 |
| Description: | Polygon motor error 1: ON timeout The polygon mirror motor does not reach the targeted operating speed: • Within 10 seconds after turning ON. • Within 10 sec. after changing speed |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective • Polygon motor defective. |
| Error code: | SC203 |
| Description: | Polygon motor error 2: OFF timeout The polygon mirror motor does leave the READY status within 10 seconds after the polygon motor switches OFF. |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective • Polygon motor defective. |
| Error code: | SC204 |
| Description: | Polygon motor error 3: Polygon motor lock signal error The polygon motor lock signal goes HIGH (inactive) while the laser diode is firing. |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective |
| Error code: | SC210 |
| Description: | Laser beam detection error 1: K (Black) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • CK Laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC211 |
| Description: | Laser beam detection error 1: Y (Yellow) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • CK laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC212 |
| Description: | Laser beam detection error 1: M (Magenta) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC213 |
| Description: | Laser beam detection error 1: C (Cyan) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC220 |
| Description: | Laser Synchronization Detector Error 1: K Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 black, or leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) on the BICU is defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC221 |
| Description: | Laser Synchronization Detector Error 2: K Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for black, leading edge for any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC222 |
| Description: | Laser Synchronization Detector Error 1: Y Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 yellow, leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) (ASIC) on the BICU defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC223 |
| Description: | Laser Synchronization Detector Error 2: Y Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for yellow, leading edgefor any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC224 |
| Description: | Laser Synchronization Detector Error 1: M Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 magenta, leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC225 |
| Description: | Laser Synchronization Detector Error 2: M Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for magenta, leading edge for any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC226 |
| Description: | Laser Synchronization Detector Error 1: C Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 cyan, leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Cycle the machine off/on • YM Laser unit defective |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC227 |
| Description: | Laser Synchronization Detector Error 2: C Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for cyan, leading edgefor any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC230 |
| Description: | FGATE error 1: Feedback remains HIGH for K write After the start of timing to create the black image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU and LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC231 |
| Description: | FGATE error 1: Feedback remains LOW for K write After the start of timing to create the black image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC232 |
| Description: | FGATE error 1: Feedback remains HIGH for Y write After the start of timing to create the yellow image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU and LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC233 |
| Description: | FGATE error 1: Feedback remains LOW for Y write. After the start of timing to create the yellow image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC234 |
| Description: | FGATE error 1: Feedback remains HIGH for M write. After the start of timing to create the magenta image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC235 |
| Description: | FGATE error 1: Feedback remains LOW for M write. After the start of timing to create the magenta image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC236 |
| Description: | FGATE error 1: Feedback remains HIGH for C write. After the start of timing to create the cyan image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU and LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC237 |
| Description: | FGATE error 1: Feedback remains LOW for C write. After the start of timing to create the cyan image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC240 |
| Description: | LD error 1: K An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD. |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC241 |
| Description: | LD error 1: Y An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Cycle the machine off/on • CK laser unit defective |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC242 |
| Description: | LD error 1: M An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC243 |
| Description: | LD error 1: C An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC268 |
| Description: | Optical unit sensor error. At power ON, one of the two temperature sensors in the optics unit detected a temperature lower than 0°C for more than 1 sec. -or- It detected a temperature higher than 100°C for more than 1 sec. |
| Causes: | After the main power switch ON, writing thermistor temperature is detected at 100ms intervals an ... • Less than -30 degrees Celsius is detected for more than 4 seconds (Thermistor defective). • More than 105 degrees Celsius is detected for more than 1 second (Thermistor short). |
| Remedy: | • Thermistor disconnected (causes extremely low temperature reading) • Thermistor damaged and short circuited (causes extremely high temperature reading) • BICU defective |
| Error code: | SC270 |
| Description: | Mirror motor upper/lower limit: Y (Yellow) The pulse rate of the mirror motor reaches the upper or lower limit. Note: SP2182 displays the pulse rate for each motor. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK laser unit defective |
| Remedy: | • 3rd mirror motor is defective. • 3rd mirror motor connecter is not connected correctly. |
| Error code: | SC271 |
| Description: | Mirror motor upper/lower limit: M (Magenta) The pulse rate of the mirror motor reaches the upper or lower limit. Note: SP2182 displays the pulse rate for each motor. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK laser unit defective |
| Remedy: | • 3rd mirror motor is defective. • 3rd mirror motor connecter is not connected correctly. |
| Error code: | SC272 |
| Description: | Mirror motor upper/lower limit: C (Cyan) The pulse rate of the mirror motor reaches the upper or lower limit. Note: SP2182 displays the pulse rate for each motor. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • 3rd mirror motor is defective. • 3rd mirror motor connecter is not connected correctly. |
| Error code: | SC285 |
| Description: | MUSIC error. An error with the MUSIC occurs four times since the last time the main power was turned ON. |
| Causes: | • A PCDU is set incorrectly • ITB is set incorrectly • Execute manual process control with SP3011-2 (Density Adjustment) • MUSIC sensor harness loose, disconnected, broken, defective • MUSIC sensor defective • ITB damaged • Laser unit defective |
| Remedy: | • ITB defective • MUSIC sensors are dirty • MUSIC sensors are defective |
| Error code: | SC300 |
| Description: | AC charge output error 1: K An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC301 |
| Description: | AC charge output error 2: M An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | • Disconnect the high voltage cable from Terminal C of the power pack. • Attach a voltmeter to the terminal. • If there is no output from the terminal, replace the power pack. -or- • If there is output from the terminal, test the resistance between the high voltage cable and the ground. • If resistance is nearly "0", check the high-voltage harness for defects and replace it if necessary. • Test the conductivity between the PCU and the ground. If there is no conductivity between the PCU and ground, replace the PCU. • If there is no charge PWM signal, replace the harness and/or BCU. |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC302 |
| Description: | AC charge output error 3: C An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | This SC is issued if the BICU detects a short in the power pack 10 times consecutively. Open circuit (+) / Short circuit (-) |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC303 |
| Description: | AC charge output error 4: Y An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | • Disconnect the high voltage cable from Terminal C of the power pack. • Attach a voltmeter to the terminal. • If there is no output from the terminal, replace the power pack. -or- • If there is output from the terminal, test the resistance between the high voltage cable and the ground. • If resistance is nearly "0", check the high-voltage harness for defects and replace it if necessary. • Test the conductivity between the PCU and the ground. If there is no conductivity between the PCU and ground, replace the PCU. • If there is no charge PWM signal, replace the harness and/or BCU. |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC304 |
| Description: | Charge Corona Error: Charge Leak (K PCU) A abnormal detection signal (H) was detected for longer than 250 ms. |
| Causes: | • Turn the machine power off/on • CGB power pack harness connectors loose, broken, defective • Corona wire caps loose, missing • CGB power pack defective • Charge corona unit connectors loose, broken, defective |
| Error code: | SC308 |
| Description: | Charge Corona Error: Wire Cleaner Error (K PCU) The charge corona wire cleaner motor remained locked after the motor was switched on, or failed to switch off within the prescribed time after cleaning started. |
| Causes: | • Turn the machine power off/on • Motor overloaded due to a physical obstruction • Motor defective |
| Error code: | SC313 |
| Description: | Charge, development error 2: M 500 ms after the black, magenta, cyan, and yellow drums start to rotate, the machine starts to monitor the AC current feedback at 8 ms intervals. This is SC is issued if the feedback for the charge unit of any color drops below 0.5V for 400 ms (50 consecutive readings). |
| Causes: | • Make sure that the settings of SP2202 are at the defaults. • Check harness connections between charge roller and transfer power pack. • Defective charge roller • Defective power pack |
| Remedy: | • Make sure that the settings of SP2202 are at the defaults. • Defective charge roller • Defective power pack |
| Error code: | SC314 |
| Description: | Charge, development error 3: C 500 ms after the black, magenta, cyan, and yellow drums start to rotate, the machine starts to monitor the AC current feedback at 8 ms intervals. This is SC is issued if the feedback for the charge unit of any color drops below 0.5V for 400 ms (50 consecutive readings). |
| Causes: | • Make sure that the settings of SP2202 are at the defaults. • Check harness connections between charge roller and transfer power pack. • Defective charge roller • Defective power pack |
| Remedy: | • Make sure that the settings of SP2202 are at the defaults. • Defective charge roller • Defective power pack |
| Error code: | SC315 |
| Description: | Charge, development error 4: Y 500 ms after the black, magenta, cyan, and yellow drums start to rotate, the machine starts to monitor the AC current feedback at 8 ms intervals. This is SC is issued if the feedback for the charge unit of any color drops below 0.5V for 400 ms (50 consecutive readings). |
| Causes: | • Make sure that the settings of SP2202 are at the defaults. • Check harness connections between charge roller and transfer power pack. • Defective charge roller • Defective power pack |
| Remedy: | • Make sure that the settings of SP2202 are at the defaults. • Defective charge roller • Defective power pack |
| Error code: | SC316 |
| Description: | AC bias charge adjustment error 1: K An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC317 |
| Description: | AC bias charge adjustment error 2: M An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC318 |
| Description: | AC bias charge adjustment error 3: C An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC319 |
| Description: | AC bias charge adjustment error 4: Y An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC320 |
| Description: | Development power pack error 1: K An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC321 |
| Description: | Development power pack error 2: M An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC322 |
| Description: | Development power pack error 3: C An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC323 |
| Description: | Development power pack error 4: Y An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC324 |
| Description: | Development motor error 1: K The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC325 |
| Description: | Development motor error 2: M The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC326 |
| Description: | Development motor error 3: C The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC327 |
| Description: | Development motor error 4: Y The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC336 |
| Description: | Developer set error 1: K The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC337 |
| Description: | Developer set error 2: M The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC338 |
| Description: | Developer set error 3: C The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC339 |
| Description: | Developer set error 4: Y The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC348 |
| Description: | Toner hopper motor error. 2 sec. after the motor START signal is output, a LOCK signal cannot be detected. |
| Causes: | • Motor harness disconnected, loose, or defective • Toner pump overload • Sub hopper overload • Toner hopper motor defective |
| Remedy: | • Motor harness disconnected, loose, or defective • Powder pump overload • Sub hopper overload • Toner hopper motor defective |
| Error code: | SC350 |
| Description: | Developer Fill Error: K The PCU failed to fill with developer from the developer bottle when SP3814-1 was executed. |
| Causes: | • Developer bottle not set correctly • Developer in the bottle is clogged and not flowing Note: For detailed information about how to handle problems developer filling, see "Handling Problems with Developer Filling" under "PCU" in Section 3. |
| Remedy: | 1. Check if the connectors on the TD sensor interface board 1 (copier) and the main control board (CN353) are properly connected. 2. Make sure 5V and 12V are provided to the TD sensor interface board 1 from the main control board (CN353). 3. Check if the harnesses are damaged. 4. Make sure TD sensor interface boards 1 and 2 are properly installed. 5. Replace TD sensor interface board s1, 2, main control board, and/or the I/O control board. |
| Error code: | SC351 |
| Description: | Developer Fill Error: M The PCU failed to fill with developer from the developer bottle when SP3814-1 was executed. |
| Causes: | • Developer bottle not set correctly • Developer in the bottle is clogged and not flowing Note: For detailed information about how to handle problems developer filling, see "Handling Problems with Developer Filling" under "PCU" in Section 3. |
| Remedy: | 1. Make sure the connectors on the TD sensor interface board 2 (revolver) and the TD sensor and slip ring are properly connected. 2. Check if the harnesses is damaged. 3. Replace the TD sensor. 4. Replace the TD sensor interface board 2. 5. Replace the TD sensor interface board 1. 6. Replace the main control board. |
| Error code: | SC352 |
| Description: | Developer Fill Error: C The PCU failed to fill with developer from the developer bottle when SP3814-1 was executed. |
| Causes: | • Developer bottle not set correctly • Developer in the bottle is clogged and not flowing Note: For detailed information about how to handle problems developer filling, see "Handling Problems with Developer Filling" under "PCU" in Section 3. |
| Error code: | SC353 |
| Description: | Developer Fill Error: Y The PCU failed to fill with developer from the developer bottle when SP3814-1 was executed. |
| Causes: | • Developer bottle not set correctly • Developer in the bottle is clogged and not flowing Note: For detailed information about how to handle problems developer filling, see "Handling Problems with Developer Filling" under "PCU" in Section 3. |
| Error code: | SC360 |
| Description: | TD sensor (Vt high) error 1: K The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC361 |
| Description: | TD sensor (Vt high) error 2: M The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC362 |
| Description: | TD sensor (Vt high) error 3: C The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC363 |
| Description: | TD sensor (Vt high) error 4: Y The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC364 |
| Description: | TD sensor (Vt low) error 1: K The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective, replace the PCU Note: The TD sensor cannot be replaced independently. The PCU must be replaced if the TD sensor is defective. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC365 |
| Description: | TD sensor (Vt low) error 2: M The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | These SC codes are issued if the TD sensor output is less than 0.5V after 10 consecutive readings. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC366 |
| Description: | TD sensor (Vt low) error 3: C The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | These SC codes are issued if the TD sensor output is less than 0.5V after 10 consecutive readings. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC367 |
| Description: | TD sensor (Vt low) error 4: Y The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | These SC codes are issued if the TD sensor output is less than 0.5V after 10 consecutive readings. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC372 |
| Description: | TD sensor adjustment error 1: K During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | The TD sensor of the affected development unit could not be initialized within 2.9±0.2V. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC373 |
| Description: | TD sensor adjustment error 2: M During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | The TD sensor of the affected development unit could not be initialized within 2.9±0.2V. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC374 |
| Description: | TD sensor adjustment error 3: C During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | TD harness sensor disconnected, loose or defective Harness between TD sensor and drawer disconnected, defective • TD sensor defective, replace the PCU Note: The TD sensor cannot be replaced independently. The PCU must be replaced if the TD sensor is defective. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC375 |
| Description: | TD sensor adjustment error 4: Y During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | The voltage reading during process control for Vsg_reg was not within the correct range (4.0±0.5V). Vsg_reg is the voltage reading of the light reflected directly from the bare surface of the ITB. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC396 |
| Description: | Drum motor error 1: K When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Disconnected or defective motor harness. • Motor slips due to excessive load |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC397 |
| Description: | Drum motor error 2: M When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Disconnected or defective motor harness. • Motor slips due to excessive load |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC398 |
| Description: | Drum motor error 3: C When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Drum motor harness loose, broken, defective • Drum motor defective • DTMB defective |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC399 |
| Description: | Drum motor error 4: Y When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Drum motor harness loose, broken, defective • Drum motor defective • DTMB defective |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC400 |
| Description: | ID sensor error 1: Calibration Before adjustment Vsg_reg<0.5 but Vsg_reg could not be adjusted to the target Vsg_reg = 4.0±0.2V during process control. |
| Causes: | • TM sensors are dirty. • A solid print out due to an electrostatic charging error • The TM sensor is defective. |
| Remedy: | • ID sensor harness disconnected, loose, defective • ID sensor dirty • ID sensor defective • ITB unit drawer connector dirty |
| Error code: | SC410 |
| Description: | ID sensor error 2: Development γ K Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC411 |
| Description: | ID sensor error 3: Development γ M Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC412 |
| Description: | ID sensor error 4: Development γ C Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC413 |
| Description: | ID sensor error 5: Development γ Y Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC414 |
| Description: | ID sensor error 6: Development start voltage K The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC415 |
| Description: | ID sensor error 7: Development start voltage M The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC416 |
| Description: | ID sensor error 8: Development start voltage C The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC417 |
| Description: | ID sensor error 9: Development start voltage Y The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC418 |
| Description: | LED error during Vsg adjustment. PWM value: Ifsg>2000 This means the current to the LED of the ID sensor is abnormal. |
| Causes: | • ID sensor dirty • ID sensor defective |
| Remedy: | • ID sensor dirty • ID sensor defective |
| Error code: | SC420 |
| Description: | Potential sensor error 1: Vd Adjustment K The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC421 |
| Description: | Potential sensor error 2: Vd Adjustment M The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC422 |
| Description: | Potential sensor error 3: Vd Adjustment C The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC423 |
| Description: | Potential sensor error 4: Vd Adjustment Y The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC424 |
| Description: | Potential sensor error 5: Vl adjustment K Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC425 |
| Description: | Potential sensor error 6: Vl adjustment M Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC426 |
| Description: | Potential sensor error 7: Vl adjustment C Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC427 |
| Description: | Potential sensor error 8: Vl adjustment Y Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC432 |
| Description: | Potential sensor error 1: Vr K Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC433 |
| Description: | Potential sensor error 2: Vr M Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC434 |
| Description: | Potential sensor error 3: Vr C Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC435 |
| Description: | Potential sensor error 4: Vr Y Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC436 |
| Description: | Potential sensor error 5: Vd K The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC437 |
| Description: | Potential sensor error 6: Vd M The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC438 |
| Description: | Potential sensor error 7: Vd C The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC439 |
| Description: | Potential sensor error 8: Vd Y The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC440 |
| Description: | Image transfer power pack error 1: K An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC441 |
| Description: | Image transfer power pack error 2: M An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC442 |
| Description: | Image transfer power pack error 3: C An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC443 |
| Description: | Image transfer power pack error 4: Y An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC445 |
| Description: | Image transfer motor error The control board of the image transfer motor generated signals that indicate there is problem with the image transfer motor. |
| Causes: | • Defective ITB contact motor • Defective ITB contact sensor • Defective ITB unit |
| Remedy: | • Image transfer motor defective • ITB control board defective • ITB overloaded • Encoder strip on the front edge of the belt damaged. |
| Error code: | SC446 |
| Description: | ITB lift motor error The state of the ITB lift sensor does not change its state (switching from OFF to ON or vice versa), even after the ITB lift motor starts rotating. |
| Causes: | The transfer belt drive motor failed to start within the prescribed time or failed during normal operation. |
| Remedy: | • ITB lift sensor dirty, disconnected, defective • ITB lift motor disconnected, defective |
| Error code: | SC447 |
| Description: | 1st Lift Motor Sensor (YCM) Error |
| Causes: | The 1st lift motor (YCM) was operating but the 1st lift motor sensor failed to detect the position of the sensor feeler within the prescribed time. |
| Remedy: | • Sensor dirty • Sensor harness disconnected or broken • Sensor defective • Motor defective |
| Error code: | SC450 |
| Description: | Transfer power pack output error An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the power pack 250 times at 2nd transfer output within 500 ms. |
| Causes: | • Damaged insulation on the high-voltage supply cable • Damaged insulation around the highvoltage power supply. • Check SIOB harness connections • SIOB defective |
| Remedy: | • Damaged insulation on the high-voltage supply cable • Damaged insulation around the highvoltage power supply. |
| Error code: | SC452 |
| Description: | PTR lift mechanism error The PTR was not detected at the home position within 2 sec. after the PTR lift motor turned on. |
| Causes: | • PTR HP sensor dirty, disconnected, defective • PTR lift motor disconnected, defective |
| Remedy: | 1. Make sure the image transfer release lever is properly set. 2. Clean the belt mark. 3. Replace the transfer belt if the belt mark peels off or is damaged. 4. Clean the belt mark sensor. 5. Replace the belt mark detection sensor. 6. Replace the I/O control board. 7. Replace the main control board. [ Signal Check ] • Belt mark: CN220-A12, TP106, or CN212- B11 on the I/O control board / CN303-B1 or TP108 on the main control board. |
| Error code: | SC455 |
| Description: | PTR motor error The lock signal from the paper transfer motor is not detected within 1 sec. after the motor switched ON. |
| Causes: | • Motor disconnected • PTR shaft locked, needs cleaning, blocked by obstruction • Drive shaft of the ITB locked and overloaded, needs cleaning, or blocked by obstruction • DRB disconnected, defective |
| Remedy: | • Motor disconnected • PTR shaft locked, needs cleaning, blocked by obstruction • Drive shaft of the ITB locked and overloaded, needs cleaning, or blocked by obstruction • DRB (motor drive board) disconnected, defective |
| Error code: | SC460 |
| Description: | Separation power pack output error An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the power pack 250 times at D(AC) within 500 ms. |
| Causes: | • Damaged insulation on the high-voltage supply cable (replace cable) • Damaged insulation around the transfer power pack |
| Remedy: | • Damaged insulation on the high-voltage supply cable • Damaged insulation around the highvoltage power supply. 1. Replace the high-voltage supply cable. 2. Replace the high-voltage power supply unit. 3. Replace the IOB. |
| Error code: | SC465 |
| Description: | PTR Motor Error |
| Causes: | The PTR motor failed to start within the prescribed time or failed during normal operation. |
| Remedy: | • PTR motor harness disconnected or broken • Physical obstruction blocking operation of the PTR unit • Motor or motor drive board defective |
| Error code: | SC466 |
| Description: | PTR Separation Motor Error |
| Causes: | The PTR separation motor was operating but the PTR separation sensor failed to detect the feeler that triggers detection of the PTR separation sensor. |
| Remedy: | • Sensor dirty • Motor harness disconnected or broken • Sensor defective • Motor defective |
| Error code: | SC467 |
| Description: | Image Transfer Roller End: C The machine detected an abnormal reading of the resistance of the transfer roller because it is near the end of its service life. |
| Causes: | • Check the connections between the transfer roller power pack the roller • Replace image transfer roller • Image transfer power pack defective |
| Error code: | SC468 |
| Description: | ITB Unit Power Pack Error: Low Output |
| Causes: | During the execution of bias feedback control, the machine detected that the output of the paper transfer power pack was less than 0.1 kV. |
| Remedy: | • High-voltage harness disconnected or broken • Paper transfer power pack defective |
| Error code: | SC472 |
| Description: | Belt Centering Roller HP Error |
| Causes: | The belt centering roller sensor did not detect the belt centering roller at HP during initialization, or the belt centering roller sensor still detected the belt centering roller at HP after the belt centering roller motor switched on |
| Remedy: | • Belt centering roller sensor detective • Belt centering roller motor defective |
| Error code: | SC480 |
| Description: | Agitator Motor Error The agitator motor error is detected twice for 10 msec during the initialization at power-on or after the cover is closed. |
| Causes: | • Disconnected or defective harness • Defective agitator motor |
| Remedy: | 1. Check or replace the harness. 2. Replace the agitator motor. |
| Error code: | SC481 |
| Description: | Drum cleaning motor error: M The drum cleaning motor failed to switch on (motor lock), or failed to reach the required speed within the prescribed time. |
| Causes: | • Motor block by physical obstruction • Motor harness loose, broken, defective • Motor defective |
| Error code: | SC482 |
| Description: | Drum cleaning motor error: C The drum cleaning motor failed to switch on (motor lock), or failed to reach the required speed within the prescribed time. |
| Causes: | • Motor block by physical obstruction • Motor harness loose, broken, defective • Motor defective |
| Error code: | SC483 |
| Description: | Drum cleaning motor error: Y The drum cleaning motor failed to switch on (motor lock), or failed to reach the required speed within the prescribed time. |
| Causes: | • Motor block by physical obstruction • Motor harness loose, broken, defective • Motor defective |
| Error code: | SC484 |
| Description: | Waste toner bottle full The toner full sensor goes HIGH for more than 500 ms, indicating that the waste toner bottle is full. |
| Causes: | • Remove the used toner bottle • Empty the used toner bottle and reinstall it |
| Remedy: | • Remove waste toner bottle, empty it |
| Error code: | SC485 |
| Description: | Waste toner transport motor error The lock signal of the waste toner transport motor remains HIGH for more than 600 ms. |
| Causes: | The used toner transport motor failed to start within the prescribed time or failed during normal operation. |
| Remedy: | • Waste toner transport motor defective |
| Error code: | SC487 |
| Description: | Waste toner bottle set error The set sensor of the waste toner bottle remains LOW for more than 500 ms. (The sensor goes HIGH when the bottle is installed correctly.) |
| Causes: | • Used toner bottle not installed • Remove used toner bottle and reinstall correctly |
| Remedy: | • Install the waste toner bottle • Remove waste toner bottle and reinstall correctly |
| Error code: | SC488 |
| Description: | Waste toner transport lock Waste toner cannot be transported to the waste toner bottle. |
| Causes: | Used toner is not being moved to the used toner bottle. |
| Remedy: | • Blockage in the line to the waste toner bottle |
| Error code: | SC490 |
| Description: | Peltier Unit error The Abnormal Condition signal or the Peltier Unit is received 10 times. |
| Causes: | • No ITB unit in the machine • Dirty TM sensor |
| Remedy: | • Peltier Unit is defective |
| Error code: | SC495 |
| Description: | ITB encoder sensor error The ITB encoder sensor that reads the encoded strip on the ITB is not functioning properly. |
| Causes: | • Sensor dirty • Sensor harness loose, broken, defective • Sensor out of position because installed incorrectly • ITB installed incorrectly |
| Remedy: | 1. Make sure that connectors CN210, 211 & CN302 are properly connected to the I/O control board and the main control board. 2. Replace the humidity sensor. 3. Replace the I/O control board. 4. Replace the main control board. [Signal Check] • Temperature: CN210-1, TP247, or CN211- A9 on the I/O control board/CN302-A1 or TP112 on the main control board |
| Error code: | SC496 |
| Description: | MUSIC sensor error The MUSIC sensor detected an abnormal pattern on the ITB because: • A/D converter exceeded upper or lower limit. • The pattern used to calculate the amount of skew is abnormal. • The reading of the pattern exceeded the length of time the LED projected light. • LED light could not be adjusted correctly. |
| Causes: | This SC is issued if one or more of the following occurred: • MUSIC sensor sampling abnormal • Sensor LED adjustment abnormal • Number of patches abnormal • ITB scratched • Main scan registration abnormal • Sub scan registration abnormal • Main scan magnification abnormal • Main scan magnification error diffusion abnormal • Lens refraction abnormal |
| Remedy: | • MUSIC sensor defective or disconnected • MUSIC pattern abnormal; do a forced process control (SP3821) and check the result (section 4.2.4). |
| Error code: | SC497 |
| Description: | Temperature and humidity sensor error 1: PCU The thermistor output of the temperature and humidity sensor above the black PCU was not within the prescribed range (0.5V to 4.2V) |
| Causes: | The machine detected one of these problems with the temperature/humidity sensor located under the rear end of the K PCDU: • The temperature sensor output was less than 0.5V or more than 2.8V three times in one minute, indicating a problem with the temperature detection. • The humidity sensor output was more than 2.4V for three times in one minute, indicating a problem with humidity detection. |
| Remedy: | • Temperature and humidity sensor harness disconnected, loose, defective • Temperature and humidity sensor defective |
| Error code: | SC498 |
| Description: | Temperature and humidity sensor error 2 The thermistor output of the temperature and humidity sensor at below the waste toner bottle was not within the prescribed range (0.5V to 4.2V) |
| Causes: | The machine detected one of these problems with the temperature/humidity sensor located under the rear end of the K PCDU: • The temperature sensor output was less than 0.5V or more than 2.8V three times in one minute, indicating a problem with the temperature detection. • The humidity sensor output was more than 2.4V for three times in one minute, indicating a problem with humidity detection. |
| Remedy: | • Temperature and humidity sensor harness disconnected, loose, defective • Temperature and humidity sensor defective |
| Error code: | SC499 |
| Description: | ITB Position Sensor error Abnormal ITB Position Sensor output. |
| Causes: | The ITB sensor that reads the encoded film strip on the edge of the image transfer belt was not operating correctly. (The TDCU constantly monitors operation of the ITB with transfer feed-back control.) |
| Remedy: | • ITB Position Sensor 1 or 2 is dirty. • ITB Position Sensor 1 or 2 is defective. • ITB encoder strip is dirty, • ITB encoder strip is damaged. • ITB movement error (e.g. the belt cannot rotate correctly due to friction). 1. Connectors for ITB Position Sensor 1 or 2 are not connected correctly. |
| Error code: | SC501 |
| Description: | Tray 1 (tandem tray) feed error (Japan Only) • The tray 1 lift sensor does not switch ON 10 s after the tray lift motor switches ON and starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. • The lower limit sensor of the tandem tray does not detect the lower limit within 10 sec. |
| Causes: | • Tray lift motor harness disconnected, loose, defective • Paper or other obstacle trapped between tray and motor • Tray lift sensor disconnected, damaged • Lower limit sensor disconnected, damaged • Pick-up solenoid disconnected, blocked by an obstacle |
| Remedy: | • Tray lift motor harness disconnected, loose, defective • Paper or other obstacle trapped between tray and motor • Tray lift sensor disconnected, damaged • Lower limit sensor disconnected, damaged • Pick-up solenoid disconnected, blocked by an obstacle |
| Error code: | SC502 |
| Description: | Tray 2 (paper cassette) feed error (Japan Only) • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. • The lower limit sensor of the tandem tray does not detect the lower limit within 10 sec. |
| Causes: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Remedy: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Error code: | SC503 |
| Description: | Tray 1 feed error • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. |
| Causes: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Remedy: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Error code: | SC504 |
| Description: | Tray 2 feed error • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. |
| Causes: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Remedy: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Error code: | SC505 |
| Description: | Tandem tray rear fence motor error • The return sensor does not switch ON within 10 sec. after the rear fence motor switches ON. • The HP sensor does not switch ON 10 sec. after the rear fence motor switches ON. • The HP sensor and return sensor switch ON at the same time. |
| Causes: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors • Paper or other obstacle trapped between tray and motor • Motor mechanical overload due to obstruction • Return sensor or HP sensor defective or dirty |
| Remedy: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors • Paper or other obstacle trapped between tray and motor • Motor mechanical overload due to obstruction • Return sensor or HP sensor defective or dirty |
| Error code: | SC510 |
| Description: | LCT tray error. • When the bottom plate is lifted, the upper limit sensor does not come on for 30 sec. • When the bottom plate is lowered, the lower limit sensor does not come on for 30 sec. • After lift begins, the upper limit sensor does not switch ON before the pick-up solenoid switches ON. • The paper end sensor switches ON during lift and the upper limit sensor does not switch ON for 2.5 s, and a message prompts user to reset paper. |
| Causes: | • Tray lift motor harness, disconnected, loose, or defective • Tray lift motor defective • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Remedy: | • Tray lift motor harness, disconnected, loose, or defective • Tray lift motor defective • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Error code: | SC515 |
| Description: | Duplex jogger motor error 1. When the jogger fence moves to the home position, the jogger fence HP sensor does not switch on even after the duplex jogger motor has moved the jogger fence 153.5 mm. |
| Causes: | The CIS cleaning fan motor in the right drawer failed to start within the prescribed time or failed during normal operation. |
| Remedy: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors or motor • Return sensor or HP sensor defective or dirty |
| Error code: | SC516 |
| Description: | Duplex jogger motor error 2. When the jogger fence moves from the home position, the jogger fence HP sensor does not turn off even if the duplex jogger motor has moved the jogger fence 153.5 mm. |
| Causes: | A LOW motor LOCK signal was not detected after the motor switched off after 10 consecutive attempts. |
| Remedy: | • Paper or other obstacle has jammed mechanism • HP sensor connector disconnected or defective • HP sensor defective |
| Error code: | SC517 |
| Description: | LCIT air assist front fan error The front air assist fan is not functioning properly. |
| Causes: | • Fan harness disconnected or damaged • Fan blocked by an obstruction • Fan damaged, defective |
| Error code: | SC518 |
| Description: | LCIT air assist rear fan error The rear air assist fan is not functioning properly. |
| Causes: | • Fan harness disconnected or damaged • Fan blocked by an obstruction • Fan damaged, defective |
| Error code: | SC530 |
| Description: | Fan error 1: fusing cooling fan motor. The BICU does not receive the lock signal 5 seconds after the fusing unit fan switches ON. |
| Causes: | • Disconnected or defective motor harness. • Defective LSU fan motor |
| Remedy: | • Fusing cooling fan disconnected, defective • BICU defective |
| Error code: | SC531 |
| Description: | Fan error 2: fusing cooling fan motor. The lock signal remained HIGH for 5 sec. while the fan at the front of the fusing unit near the heat dissipation fins was operating. |
| Causes: | • Disconnected or defective motor harness. • Defective LSU fan motor |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC532 |
| Description: | Fan error 3: PCB box fan. The lock signal remained HIGH for 5 sec. while the fan that cools the printed circuit boards was operating. |
| Causes: | • Disconnected or defective motor harness. • Defective air intake fan motor |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC533 |
| Description: | Fan error 4: fusing exhaust fan. The lock signal remained HIGH for 5 sec. while the fan that draws air out of the fusing unit was operating. |
| Causes: | • Disconnected or defective motor harness. • Defective PSU fan motor |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC534 |
| Description: | Fan error 5: duplex exhaust fan. The lock signal remained HIGH for 5 sec. while the fan that draws air out of the duplex unit was operating. |
| Causes: | • Fan harness disconnected or damaged • Fan blocked by an obstruction • Fan damaged |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC535 |
| Description: | Temperature/Humidity control abnormal. The output of the temperature/humidity sensor reaches the upper or lower limit, even after the Peltier unit has been ON for 3 hours. |
| Causes: | This is the small fan to the left or the large pressure roller fan on the front of the left drawer. |
| Remedy: | • Peltier Cooling Fan Motor is defective. |
| Error code: | SC536 |
| Description: | Drive Exhaust Fan Error |
| Causes: | The fan motor failed to start within the prescribed time or stopped during normal operation. The drive exhaust fan is located near the upper left corner of the machine at the rear. |
| Remedy: | • Fan motor harness disconnected or broken • Fan motor defective |
| Error code: | SC537 |
| Description: | Toner Supply Cooling Fan Error |
| Causes: | The fan motor failed to start within the prescribed time or stopped during normal operation. The toner supply cooling fan is inside the duct at the upper right corner at the rear of the machine. It is inside the duct that runs past the YM laser unit and connects behind the toner supply units. |
| Remedy: | • Fan motor harness disconnected or broken • Fan motor defective |
| Error code: | SC538 |
| Description: | Controller Box Intake Fan Error |
| Causes: | One of the fans at the bottom edge of the controller box failed to start within the prescribed time or stopped during normal operation. |
| Remedy: | • Fan motor harness disconnected or broken • Fan motor defective |
| Error code: | SC539 |
| Description: | Development Unit Cooling Fan Error |
| Causes: | One of the three large fans that cool the liquid coolant through the radiator failed to start within the prescribed time or stopped during normal operation. These fans are located in the cooling box at the back of the machine. |
| Remedy: | • Fan motor harness disconnected or broken • Fan motor defective |
| Error code: | SC540 |
| Description: | Fusing/exit motor error Motor operation was detected abnormal at power on. |
| Causes: | • Check inside the fusing unit for any obstructions • Motor harness loose, broken, defective • Motor or its driver board defective |
| Error code: | SC541 |
| Description: | Heating roller thermistor 1 error 1: Poor connection. The temperature measured by the heating roller thermistor does not reach 130°C after 10 tries and 65 sec. have elapsed. |
| Causes: | • Disconnected thermistor • Defective harness connection |
| Remedy: | • Heating roller thermistor harness connection loose, disconnected, defective • Defective heating roller thermistor |
| Error code: | SC543 |
| Description: | Heating roller thermistor 1 error 3: Software - High temperature. The thermistor detected a temperature over 230°C. |
| Causes: | • Defective I/O control (EGB) • Defective EGB |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature out of control Do SP5810 to cancel the SC fusing code. |
| Error code: | SC544 |
| Description: | Heating roller thermistor 1 error 4: Hardware - High temperature. The thermistor detected a temperature over 260°C. |
| Causes: | The machine detected the CPU port LOW twice at 100 ms intervals and issued this SC. This check is always done to check for overheating, even if SC543 does not detect the problem. |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC545 |
| Description: | Heating roller thermistor 1 error 5: Lamp remains ON. After hot roller reaches warmup temperature, the fusing lamps remained ON at full capacity for 25 sec. after reaching the warmup temperature while the hot roller was not rotating. |
| Causes: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken |
| Error code: | SC546 |
| Description: | Heating roller thermistor 2 error 1: Thermistor disconnected. The temperature measured by the heating roller thermistor does not reach 0°C after 45 sec. and remains over this temperature for 10 readings. |
| Causes: | Unstable connector contact of fusing thermistor |
| Remedy: | • Loose connection of the heating roller thermistor • Defective heating roller thermistor |
| Error code: | SC547 |
| Description: | Zero cross error. When the main switch is turned ON, the machine checks how many zero-cross signals are generated within 500 ms. This SC code is issued if the number of zerocross signals detected is either more than 66 or less than 45 for 10 readings. Note: Zero cross signals, generated from an ac power supply, are used to generate a trigger pulses to control the applied power accurately. |
| Causes: | Defective fusing lamp relay |
| Remedy: | • Electrical noise on the power supply line • Fusing relay damaged: replace the PSU. Normally, this SC is cancelled if you do SP5810 to cancel the SC fusing code. |
| Error code: | SC549 |
| Description: | Heating roller thermistor 2 error 3: Software - High Temperature. The thermistor detected a temperature over 250°C. |
| Causes: | • Do SP5810 to cancel the SC fusing code. • TRIAC short, AC drive board defective • VBCU defective |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic. Do SP5810 to cancel the SC fusing code. |
| Error code: | SC550 |
| Description: | Heating roller thermistor 2 error 4: Hardware - High Temperature. The thermistor detected a temperature over 260°C. |
| Causes: | • Do SP5810 to cancel the SC fusing code. • TRIAC short, AC drive board defective • VBCU defective |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC551 |
| Description: | Pressure roller thermistor error 1. The temperature measured by the pressure roller thermistor does not reach 0°C for 200 sec. |
| Causes: | In the condition of relay ON, the end thermistor on the fusing detects less than 0 degrees Celsius for more than 5 seconds. |
| Remedy: | • Loose connection of the pressure roller thermistor • Defective pressure roller thermistor • Defective BICU Do SP5810 to cancel the SC fusing code. |
| Error code: | SC552 |
| Description: | Pressure roller thermistor error 2. After the main switch is turned ON or the cover is closed, the heating roller temperature does not reach the ready temperature within 2 sec. after the heater switches ON. -or- If the roller was below 45°C, the heating roller did not reach the ready temperature 2 sec. after reaching 45°C. Note: Thermistor 2 stops monitoring the temperature once Thermistor 1 detects ready temperature. |
| Causes: | • Defective or deformed non-contact thermistor • Incorrect power supply input at the main power socket |
| Remedy: | • Pressure roller thermistor harness loose, disconnected, defective • Pressure roller thermistor defective |
| Error code: | SC553 |
| Description: | Pressure roller thermistor error 3: Software -High temperature. The thermistor detected a temperature over 220°C. |
| Causes: | • Defective main board • Defective PSU |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC554 |
| Description: | Pressure roller thermistor error 4: Hardware - High temperature. The thermistor detected a temperature over 230°C. |
| Causes: | • Defective main board • Defective PSU • Defective fusing unit |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC555 |
| Description: | Pressure roller thermistor error 5: Lamp remains ON. After hot roller reaches warmup temperature, the pressure roller fusing lamp remains for 6 sec. while the hot roller is not rotating. |
| Causes: | The fusing lamp reached the warm-up temperature and then attained fusing temperature (full power), but remained on after paper passed through the fusing unit (hot roller was not rotating). |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken Do SP5810 to cancel the SC fusing code. |
| Error code: | SC556 |
| Description: | Heating roller thermistor 2 error 5: Lamp remains ON. After hot roller reaches warmup temperature, the pressure roller fusing lamp remains for 6 sec. while the hot roller is not rotating. |
| Causes: | More than 1 degree Celsius temperature difference (between Center – End thermistor) is detected for 1.5 seconds 5 times in a row. |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken |
| Error code: | SC557 |
| Description: | Zero Cross Frequency Error The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Causes: | • Defective fusing lamp relay • Unstable input power source |
| Remedy: | 1. Check the power supply source. 2. Replace the fusing unit. |
| Error code: | SC559 |
| Description: | Consecutive Fusing Jam The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Fuser SC Detect" in the SP Mode 2 tab. |
| Causes: | • Defective fusing unit • Defective fusing control |
| Remedy: | 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. |
| Error code: | SC561 |
| Description: | Hot roller thermistor error 1: Thermistor disconnected. The temperature measured by the hot roller thermistor does not reach the prescribed warm-up temperature within 100 sec. |
| Causes: | Temperature detected at less than 0°C. Note: These are the two NC sensors on the side of the fusing unit. |
| Remedy: | • Loose connection of the hot roller thermistor • Defective hot roller thermistor • Defective BICU |
| Error code: | SC562 |
| Description: | Hot roller thermistor error 2: Failure to reach warmup temperature. After the main switch is turned ON or the cover is closed, the heating roller temperature does not reach the ready temperature within 2 sec. after the heater switches ON. -or- If the roller was below 45°C, the heating roller did not reach the ready temperature 2 sec. after reaching 45°C. Note: Thermistor 2 stops monitoring the temperature once Thermistor 1 detects ready temperature. |
| Causes: | Fusing temperature control failed to achieve the warm-up temperature. Note: These are the two NC sensors on the side of the fusing unit. |
| Remedy: | • Hot roller fusing lamp broken • Defective hot roller thermistor • Defective BICU. Do SP5810 to cancel the SC fusing code. |
| Error code: | SC563 |
| Description: | Hot roller thermistor error 3: Software - High Temperature. The thermistor detected a temperature over 250°C 10 times within 1 sec. |
| Causes: | Temperature incorrect due to a TRIAC short or other problem with IOB or AC drive board |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC564 |
| Description: | Hot roller thermistor error 4: Hardware - High Temperature. The thermistor detected a temperature over 260°C. |
| Causes: | Temperature incorrect due to a TRIAC short or other problem with IOB or AC drive board |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC565 |
| Description: | Hot roller thermistor error 5: Lamp remains ON. After hot roller reaches warmup temperature, the hot roller fusing lamp remains for 6300 sec. while the hot roller is not rotating. |
| Causes: | • Do SP5810 to cancel the SC fusing code. • Thermistor damaged, or out of position • Fusing lamp disconnected, broken |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken Do SP5810 to cancel the SC fusing code. |
| Error code: | SC568 |
| Description: | Thermistor 4 Error: Hardware Error |
| Causes: | Temperature incorrect due to a TRIAC short or other problem with IOB or AC drive board |
| Remedy: | • Do SP5810 to cancel the fatal error • IOB harness disconnected or broken • AC drive board harness disconnected or broken • AC drive board defective • IOB defective |
| Error code: | SC569 |
| Description: | Pressure Roller Lift Error |
| Causes: | Pressure roller lift motor not operating correctly. No signal to indicate completion of operation. |
| Remedy: | • Pressure roller lift sensor harness disconnected or broken • Pressure roller lift sensor dirty • Pressure roller lift harness disconnected or broken • Pressure roller lift motor blocked by an obstruction • Pressure roller lift motor defective |
| Error code: | SC570 |
| Description: | Ozone Collection Fan Error |
| Causes: | The ozone collection fan is the large fan on the right end of the upper horizontal duct across the back of the machine. |
| Remedy: | • Fan harness disconnected or broken • Fan overload due to physical obstruction • Fan motor defective |
| Error code: | SC571 |
| Description: | Thermistor 6 Error: Poor Connection |
| Causes: | Temperature detected at less than 0°C. Note: This is the contact thermistor under the pressure roller at the front of the fusing unit. |
| Remedy: | • Do SP5810 to cancel the fatal error • Harness disconnected or broken • Poor contact with surface of pressure roller • Thermistor defective |
| Error code: | SC572 |
| Description: | Thermistor 6 Error: Warm-up Temperature |
| Causes: | Fusing temperature control failed to achieve the warm-up temperature. |
| Remedy: | • Do SP5810 to cancel the fatal error • Thermistor deformed • Thermistor floating free • Input voltage incorrect • Fusing lamp disconnected |
| Error code: | SC573 |
| Description: | Ozone intake fan error The ozone filter intake fan not operating correctly. |
| Causes: | • Fan harness loose, broken, defective • Fan overload due to physical obstruction • Fan motor defective |
| Error code: | SC574 |
| Description: | Y thermistor error The thermistor near the Y PCU has short circuited or otherwise not operating correctly. |
| Causes: | • Harness loose, broken, defective • Thermistor defective |
| Error code: | SC599 |
| Description: | Paper Height Sensor Error |
| Causes: | One or more of the four paper height sensors in Tray 1 of the main machine is not functioning correctly. |
| Remedy: | • Condensation on one or more of the sensors • Sensor harness damaged, defective • Sensor connector loose, broken, defective • IOB defective |
| Error code: | SC620 |
| Description: | ARDF communication error. A BREAK signal occurs after the machine detects the ARDF, or a communication timeout occurs. |
| Causes: | No response from the ADF after connection to the main machine or an error occurred after connection. |
| Remedy: | • ARDF disconnected • IPU board harness disconnected, defective • IPU board defective • Spurious noise from the power supply line • ARDF control board defective |
| Error code: | SC621 |
| Description: | Mailbox-to-Finisher communication error. Communication between the mailbox and finisher is interrupted. An ACK/NCK signal was not received within 100 ms after a data frame is sent and 3 retries failed. |
| Causes: | The UART generated an error when the finisher was connected. |
| Remedy: | • Connection cable between mailbox and finisher disconnected, defective • Finisher main board defective • BICU defective • PSU defective |
| Error code: | SC622 |
| Description: | LCT communication error. Communication between the copier and LCT is interrupted. An ACK/NCK signal was not received within 100 ms after a data frame is sent and 3 retries failed. |
| Causes: | • Paper tray control board defective • BCU defective • IOB defective • Paper tray-main machine connection error |
| Remedy: | • Connection cable between the LCT and copier is disconnected, defective • LCT main board defective • BICU defective • PSU defective |
| Error code: | SC624 |
| Description: | Mailbox-to-copier communication error. Communication between the mailbox and copier is interrupted. An ACK/NCK signal was not received within 100 ms after a data frame is sent and 3 retries failed. |
| Causes: | • Mailbox cable disconnected, defective • Mailbox main board defective • VBCU defective • PSU defective |
| Remedy: | • Mailbox cable disconnected, defective • Mailbox main board defective • BICU defective • PSU defective |
| Error code: | SC625 |
| Description: | VBCU-DTMB (DMC1) communication error Communication between the VBCU and DMC (main) was interrupted. An ACK/NAK signal was not received within 100 ms after a data frame was sent and three retries failed. |
| Causes: | • Check the DTMB harness connections at the DTMB and VBCU • DTMB defective • PSU defective • VBCU defective • 5V power supply defective |
| Remedy: | 1. Check the connector of the optical-fiber cable is properly set on the FPU main board and main control board or check if it is damaged. 2. Replace the FPU main board. 3. Replace the scanner IPU board. |
| Error code: | SC626 |
| Description: | VBCU-DTMB (DMC2) communication error Communication between the VBCU and DMC (sub) was interrupted. An ACK/NAK signal was not received within 100 ms after a data frame was sent and three retries failed. |
| Causes: | • Check the DTMB harness connections at the DTMB and VBCU • DTMB defective • VBCU defective • PSU defective |
| Remedy: | 1. Make sure the harness is properly connected to the main control board, I/F board RDS/LCT, and the LCT main board. 2. Check for damage to the harness. 3. Replace the I/F board RDS/LCT. 4. Replace the LCT main board. 5. Replace the main control board. |
| Error code: | SC627 |
| Description: | VBCU-DTMB (TMC) communication error Communication between the VBCU and TMC was interrupted. An ACK/NAK signal was not received within 100 ms after a data frame was sent and three retries failed. |
| Causes: | • DTMB harness loose, broken, defective • DTMB defective • VBCU defective • PSU defective |
| Error code: | SC687 |
| Description: | Memory address command error. The BICU does not receive a memory address command from the controller 120 seconds after paper is in the position for registration. |
| Causes: | The BICU did not receive a memory address command from the controller within the prescribed time after the paper reached the registration sensor. |
| Remedy: | • BICU-Controller connection loose, defective • BICU defective • Controller defective |
| Error code: | SC701 |
| Description: | Original pick-up operation error. Even though the pick-up motor is rotating clock-wise, the pick-up roller home position sensor cannot detect the position of the pickup roller. |
| Causes: | Even though the pickup motor is rotating clock-wise, the pickup roller home position sensor cannot detect the position of the pickup roller. |
| Remedy: | • Pick-up roller HP sensor harness loose, disconnected, defective • Pick-up roller HP sensor defective • Pick-up motor harness loose, disconnected, defective • Pick-up motor defective • ARDF control board defective |
| Error code: | SC705 |
| Description: | ARDF bottom plate lift motor. • The bottom plate HP sensor did not detect the home position of the bottom plate after the bottom plate lift motor switches ON and lowers the bottom plate. • The bottom plate position sensor does not detect the position of the plate after the lift motor switches ON and raises the bottom plate. |
| Causes: | The bottom plate HP sensor did not detect the home position of the bottom plate after the bottom plate lift motor switches on and lowers the bottom plate. The bottom plate position sensor does not detect the position of the plate after the lift motor switches on and raises the bottom plate. |
| Remedy: | • ARDF feed motor disconnected, defective • Bottom plate HP sensor disconnected, defective • ARDF main board defective |
| Error code: | SC720 |
| Description: | Finisher lower transport motor error. No encoder pulse signal is detected for the transport motor within the prescribed time. The 1st failure issues an original jam message, and the 2nd failure issues this SC code. |
| Causes: | • Harness short-circuit -80 only • Overload • Motor defective • Solenoid defective -03, -80 only • Connector disconnected • Encoder defective -10, -25, -34 -81 only • Home position sensor defective |
| Remedy: | • Lower transport motor disconnected, defective • Finisher connection to transport motor loose, defective • Lower transport motor defective • Finisher main board defective |
| Error code: | SC721 |
| Description: | Finisher jogger motor error. The jogger fences move out of the home position but the HP sensor output does not change within the specified number of pulses. The 1st failure issues an original jam message, and the 2nd failure issues this SC code. |
| Causes: | • Overcurrent (-03 only) • Staple jam (-44 only) • Encoder error (-11, -11, -25, -44) • Motor defective • Connecter disconnected, or loose • Motor overload • HP sensor defective • Paper surface sensor defective (-70 only) |
| Remedy: | • Jogger HP sensor disconnected, defective • Jogger motor disconnected, defective • Jogger motor overloaded due to obstruction • Finisher main board and jogger motor connection loose, defective • Finisher main board defective |
| Error code: | SC723 |
| Description: | Finisher feed-out motor. The stack feed-out belt HP sensor does not activate within the specified time after the stack feed-out belt motor turns ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The motor that drives the rotation of the positioning sponge roller is not operating. |
| Remedy: | • Stack feed-out HP sensor disconnected, defective • Feed-out motor disconnected, defective • Finisher main board connection to feed out motor disconnected, defective • Motor overload due to obstruction |
| Error code: | SC724 |
| Description: | Finisher stapler hammer motor error. Stapling does not finish within the prescribed time after the staple hammer motor turns ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The motor that lowers and raises the positioning roller above the stapling tray not operating. |
| Remedy: | • Stapler hammer motor overloaded due to obstruction, jammed staple, number of sheets exceeds limit for stapling • Stapler hammer motor disconnected, defective • Staple hammer motor HP sensor disconnected, defective |
| Error code: | SC725 |
| Description: | Finisher exit guide plate motor error. After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The motor that opens and closes the exit guide at the shift tray exit is not operating correctly. |
| Remedy: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Error code: | SC726 |
| Description: | Shift jogger motor 1 error. The sides fences do not retract within the prescribed time after the shift jogger motor switches ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The drag roller arm with the sponge roller did not return to its home position within the prescribed time. |
| Remedy: | • Shift jogger motor disconnected, defective • Shift jogger motor overloaded due to obstruction • Shift jogger HP sensor disconnected, defective |
| Error code: | SC727 |
| Description: | Shift jogger motor 2 error. The side fences do not retract within the prescribed time after the shift jogger motor switches ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Error code: | SC728 |
| Description: | Shift jogger retraction motor error. The side fences do not retract within the prescribed time after the retraction motor switches ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The side fences at the exit of the finisher did not leave (or arrive at) their home positions within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Error code: | SC730 |
| Description: | Finisher Tray 1 shift motor error. The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Error code: | SC731 |
| Description: | Proof (upper) tray exit motor error Finishers (D512/D513) |
| Causes: | Motor drive board output abnormal, or short circuit detected on the board. The 1st failure issues this SC code. |
| Remedy: | • Motor disconnected, defective • Finisher connection to motor loose, defective • Motor blocked by an obstruction • Motor defective |
| Error code: | SC732 |
| Description: | Shift tray exit motor error Finishers (D512/D513) |
| Causes: | The shift tray exit motor is not operating. |
| Remedy: | • Motor harness disconnected or defective • Motor is blocked by an obstruction • Motor defective • Finisher main board defective |
| Error code: | SC733 |
| Description: | Stapler exit motor error Finishers (D512/D513) |
| Causes: | The stapler exit motor is not operating. |
| Remedy: | • Motor harness disconnected or defective • Motor is blocked by an obstruction • Motor defective • Finisher main board defective |
| Error code: | SC734 |
| Description: | Proof tray junction gate motor error Finishers (D512/D513) |
| Causes: | The proof tray JG HP sensor did not detect the junction gate at (or out of) its home position within 2 s. |
| Remedy: | • Proof junction gate HP sensor dirty • Sensor harness or connector disconnected or defective • Proof junction gate motor harness or connector disconnected or defective • Sensor defective • Motor defective • Finisher main board defective |
| Error code: | SC735 |
| Description: | Stapler junction gate motor error Finishers (D512/D513) |
| Causes: | The stapler JG HP sensor did not detect the stapler junction gate at (or out of) its home position within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Stapler junction gate HP sensor dirty • Sensor harness or connector disconnected or defective • Stapler junction gate motor harness or connector disconnected or defective • Sensor defective • Motor defective • Finisher main board defective |
| Error code: | SC736 |
| Description: | Pre-Stack Junction Gate Motor Error: 3K Finisher B830 The pre-stack junction gate HP sensor did not detect the gate at the home position for within 200 ms after two attempts. -or- The HP sensor twice detected the gate at the home position for more than 200 ms after it was supposed to open. |
| Causes: | • Junction gate did not arrive at the home position within the specified time • Junction gate did not leave the home position within the specified time |
| Error code: | SC737 |
| Description: | Pre-stack motor error Finishers (D512/D513) |
| Causes: | The pre-stack motor that moves the pre-stack roller is not operating. |
| Remedy: | • Motor harness disconnected or defective • Motor is blocked by an obstruction • Pre-stack roller HP sensor dirty • Pre-stack roller HP sensor harness or connector disconnected or defective • Motor defective • Sensor defective • Finisher main board defective |
| Error code: | SC738 |
| Description: | Pre-stack jg motor error Finishers (D512/D513) |
| Causes: | The pre-stack JG motor that operates the pre-stack junction gate is not operating. The pre-stack junction gate sensor did not detect the junction gate in (or out of) its home position within the prescribed time. |
| Remedy: | • Pre-stack JG motor harness or connector disconnected or defective • Pre-stack JG HP sensor dirty • Sensor harness or connector disconnected or defective • Motor defective • Sensor defective • Finisher main board defective |
| Error code: | SC740 |
| Description: | Finisher corner stapler motor error. The stapler motor does not switch off within the prescribed time after operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The stapler motor did not switch off within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Remedy: | • Staple jam • Number of sheets in the stack exceeds the limit for stapling • Stapler motor disconnected, defective |
| Error code: | SC741 |
| Description: | Finisher corner stapler rotation motor error. The stapler does not return to its home position within the specified time after stapling. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The stapler did not return to its home position (or did not leave its home position) within the specified time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Stapler rotation motor disconnected, defective • Stapler rotation motor overloaded due to obstruction • Stapler rotation HP sensor disconnected, defective |
| Error code: | SC742 |
| Description: | Finisher stapler movement motor error. The stapler HP sensor is not activated within the specified time after the stapler motor turned ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The stapler did not return to its home position (or leave its home position) within the specified time after stapling. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Stapler movement motor disconnected, defective • Stapler movement motor overloaded due to obstruction • Stapler HP sensor disconnected, defective |
| Error code: | SC743 |
| Description: | Booklet stapler motor error 1. The front stapler unit saddlestitch motor does not start operation within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The booklet stapler motor did not start stapling within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Front motor disconnected, defective • Front motor overloaded due to obstruction |
| Error code: | SC744 |
| Description: | Booklet stapler motor error 2. The rear stapler unit saddlestitch motor does not start operation within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Rear motor disconnected, defective • Rear motor overloaded due to obstruction |
| Remedy: | • Rear motor disconnected, defective • Rear motor overloaded due to obstruction |
| Error code: | SC745 |
| Description: | Feed-out belt motor error Finishers (D512/D513) |
| Causes: | The stack feed-out belt HP sensor did not activate within the specified time after the stack feed-out belt motor turned on. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • If the motor is operating 1. Stack feed-out belt HP sensor harness disconnected or defective 2. Sensor defective • If the motor is not operating: 1. Feed-out belt motor blocked by an obstruction 2. Motor harness disconnected or defective 3. Motor defective 4. Finisher main board defective |
| Error code: | SC746 |
| Description: | Stack plate motor error 1: front motor Finishers (D512/D513) |
| Causes: | The stack plate HP sensor (front) did not activate within the prescribed time after the motor turned on. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • If the motor is operating 1. Front stack plate HP sensor harness disconnected or defective 2. Front stack plate HP sensor defective • If the motor is not operating: 1. Motor blocked by an obstruction 2. Motor harness disconnected or defective 3. Motor defective 4. Booklet finisher main board defective |
| Error code: | SC747 |
| Description: | Stack plate motor error 2: center motor Finishers (D512/D513) |
| Causes: | The stack plate HP sensor (center) did not activate within the prescribed time after the motor turned on. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • If the motor is operating 1. Center stack plate HP sensor harness disconnected or defective 2. Center stack plate HP sensor defective • If the motor is not operating: 1. Motor blocked by an obstruction 2. Motor harness disconnected or defective 3. Motor defective 4. Booklet finisher main board defective |
| Error code: | SC748 |
| Description: | Stack plate motor error 3: rear motor Finishers (D512/D513) |
| Causes: | The stack plate HP sensor (rear) did not activate within the prescribed time after the motor turned on. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • If the motor is operating 1. Rear stack plate HP sensor harness disconnected or defective 2. Rear stack plate HP sensor defective • If the motor is not operating: 1. Motor blocked by an obstruction 2. Motor harness disconnected or defective 3. Motor defective 4. Booklet finisher main board defective |
| Error code: | SC750 |
| Description: | Finisher tray 1 (upper tray lift) motor error. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The shift tray paper height sensor did not change its status within the prescribed time after the tray was raised or lowered. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Tray lift motor disconnected, defective • Upper tray paper height sensor disconnected, defective • Finisher main board connection to motor loose • Finisher main board defective |
| Error code: | SC753 |
| Description: | Return roller motor error. Occurs during the operation of the lower tray pressure motor. |
| Causes: | The drag roller HP sensor did not detect the drag roller in (or out of) its home position within the prescribed time. (The drag drive motor drives the timing belt that rotates the drag roller at the shift tray exit.) |
| Remedy: | • Motor harness disconnected, loose, defective • Motor overloaded • Home position sensor harness disconnected, loose, defective • Home position defective |
| Error code: | SC754 |
| Description: | Drag roller motor error Finishers (D512/D513) |
| Causes: | The drag roller motor did not turn on. (The drag roller motor drives the shaft that moves the drag roller left and right at the shift tray exit.) |
| Remedy: | • Motor harness disconnected or defective • Motor defective • Finisher control board defective |
| Error code: | SC755 |
| Description: | Shift motor error Finishers (D512/D513) |
| Causes: | The shift tray HP sensors did not detect the shift tray in (or out of) its home position within the prescribed times. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. Note: In the Finisher SR5000 (B830), these sensors are the "half-turn" sensors. |
| Remedy: | • If the motor is operating 1. HP sensor harnesses disconnected or defective 2. HP sensor defective • If the motor is not operating: 1. Motor blocked by an obstruction 2. Motor harness disconnected or defective 3. Motor defective 4. Finisher main board defective |
| Error code: | SC760 |
| Description: | Finisher punch motor error. The punch HP sensor is not activated within the specified time after the punch motor turned ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The punch HP sensor did not detect the punch movement motor in (or out) of its home position within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Punch HP sensor disconnected, defective • Punch motor disconnected, defective • Punch motor overload due to obstruction |
| Error code: | SC761 |
| Description: | Finisher folder plate motor error. The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | 1. Over current of bridge unit motor 2. Over current due to short-circuit in PCB |
| Remedy: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Error code: | SC763 |
| Description: | Punch movement motor error. Occurs during operation of the punch unit. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The punch movement HP sensor did not detect the punch at its home position (or out of its home position) within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC764 |
| Description: | Paper position sensor slide motor error. Occurs during operation of the punch unit. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The system detected an error at the CIS (Contact Image Sensor) inside the punch unit during paper registration for paper punching. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC765 |
| Description: | Folding unit bottom fence lift motor. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The bottom fence in the booklet fold unit did not return to the home position within the specified time. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC766 |
| Description: | Clamp roller retraction motor error. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The clamp roller did not return to the home position within the specified time. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC767 |
| Description: | Stack junction gate motor error. Occurs during operation of the punch unit. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Stack junction mechanism overloaded due to an obstruction • Stack junction gate HP sensor connector loose, broken, defective • Stack junction gate HP sensor defective • Stack junction gate motor connector loose, broken, defective • Stack junction gate motor defective • Main control board defective |
| Remedy: | • Motor harness disconnected, loose, defective • Motor overload • Motor defective |
| Error code: | SC770 |
| Description: | Cover interposer tray bottom plate motor error. • After the motor starts to raise the bottom plate, the bottom plate position sensor does not detect the plate at the specified time (3 s). • After the motor starts to lower the bottom plate, the bottom plate HP sensor does not detect the bottom plate. |
| Causes: | In the first tray: • The upper limit sensor did not detect the bottom plate within the specified time after the lift motor switched on to lift the bottom plate. • The lower limit sensor did not direct the bottom plate within the specified time after the lift motor switched on to lower the bottom plate. Note: In both cases, 1 error count indicates a jam, 2 error counts issue this SC code. |
| Remedy: | • Bottom plate position sensor, disconnected, defective • Bottom plate HP sensor disconnected, defective |
| Error code: | SC771 |
| Description: | Cover interposer lift motor 2 error CIT D518 |
| Causes: | In the second tray: • The upper limit sensor did not detect the bottom plate within the specified time after the lift motor switched on to lift the bottom plate. • The lower limit sensor did not direct the bottom plate within the specified time after the lift motor switched on to lower the bottom plate. Note: In both cases, 1 error count indicates a jam, 2 error counts issue this SC code. |
| Remedy: | • Lift motor, upper limit sensor, lower limit sensor harnesses, connectors disconnected or defective • Lift motor defective • Upper limit sensor defective • Lower limit sensor defective |
| Error code: | SC772 |
| Description: | Cover interposer pickup motor 1 error CIT D518 |
| Causes: | In the first tray: • While the pick-up roller motor was on, the pick-up roller HP sensor did not detect the pick-up roller at the home position within the specified number of pulses. • While the pick-up roller motor was on, the pick-up roller HP sensor did not detect the pick-up roller at the home position above the specified number of pulses. Note: In both cases, 1 error count indicates a jam, 2 error counts issue this SC code. |
| Remedy: | • The pick-up motor, pick-up roller HP sensor harnesses, connectors were disconnected or defective • Pick-up motor overload due to an obstruction • Pick-up motor defective • Pick-up roller HP sensor defective |
| Error code: | SC773 |
| Description: | Cover interposer pickup motor 2 error CIT D518 |
| Causes: | In the second tray: • While the pick-up roller motor was on, the pick-up roller HP sensor did not detect the pick-up roller at the home position within the specified number of pulses. • While the pick-up roller motor was on, the pick-up roller HP sensor did not detect the pick-up roller at the home position above the specified number of pulses. Note: In both cases, 1 error count indicates a jam, 2 error counts issue this SC code. |
| Remedy: | • The pick-up motor, pick-up roller HP sensor harnesses, connectors were disconnected or defective • Pick-up motor overload due to an obstruction • Pick-up motor defective • Pick-up roller HP sensor defective |
| Error code: | SC775 |
| Description: | Cover interposer tray feed motor |
| Causes: | The top fence HP sensor did not detect the top fence at (or out of) the home position within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor overload • Motor defective |
| Error code: | SC776 |
| Description: | Bottom Fence Motor Error Finishers D512/D513 |
| Causes: | The bottom fence HP senstor did not detect the bottom fence at (or out of) the home position within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • If the bottom fence motor is operating: 1. Bottom fence HP sensor dirty 2. Sensor harness disconnected or defective 3. Sensor defective • If the bottom fence motor is not operating: 1. Bottom fence motor blocked by an obstruction 2. Motor harness disconnected or defective 3. Motor defective 4. Finisher main board defective |
| Error code: | SC780 |
| Description: | Z-Fold feed motor error Japan Only. The feed motor does not attain the prescribed speed within the specified time. |
| Causes: | • Motor harness loose, broken, defective • Motor blocked by an obstruction • Motor defective |
| Remedy: | • Feed motor disconnected, defective • Feed motor overloaded due to obstruction • Feed motor lock |
| Error code: | SC781 |
| Description: | Z-Fold lower stopper motor Japan Only. The lower stopper motor does not attain the prescribed speed within the specified time. |
| Causes: | • Lower stopper motor disconnected, defective • Lower stopper motor overloaded due to obstruction • Lower stopper HP sensor disconnected, defective |
| Remedy: | • Lower stopper motor disconnected, defective • Lower stopper motor overloaded due to obstruction • Lower stopper HP sensor disconnected, defective |
| Error code: | SC782 |
| Description: | Z-Fold upper stopper motor Japan Only. The upper stopper motor does not attain the prescribed speed within the specified time. |
| Causes: | • Upper stopper motor disconnected, defective • Upper stopper motor overloaded due to obstruction • Upper stopper HP sensor disconnected, defective |
| Remedy: | • Upper stopper motor disconnected, defective • Upper stopper motor overloaded due to obstruction • Upper stopper HP sensor disconnected, defective |
| Error code: | SC784 |
| Description: | Z-Fold Timing Sensor Adjustment Error 1 The output voltage light emitted from the sensor changed, but the return input was not sufficient to attain V0. |
| Causes: | • Sensor, mirror dirty from paper dust, other particles • Harness loose, broken, defective • Mirror out of position |
| Error code: | SC785 |
| Description: | Z-Fold Timing Sensor Adjustment Error 2 The output voltage light emitted from the sensor changed, but the return input was not sufficient to attain V0. |
| Causes: | • Sensor, mirror dirty from paper dust, other particles • Harness loose, broken, defective • Mirror out of position |
| Error code: | SC786 |
| Description: | Z-Fold Memory Error Several attempts to write to the Zfold memory failed. |
| Causes: | • Turn the machine power off/on • EEPROM on Z-Folder main board defective |
| Error code: | SC817 |
| Description: | Boot loader error. The boot loader cannot read one of the following: self-diagnostic module, kernel, or one of the files of the root file system, or the check of one of these items on the system SD card failed. |
| Causes: | • File or module on the system SD card is corrupted • File or module on the system SD card is illegal • Make sure that the system SD card is the one designed for the machine • Replace controller board. |
| Remedy: | • File or module on the system SD card is corrupted • File or module on the system SD card is illegal • Make sure that the system SD card is the one designed for the machine • Replace system ROM on the controller board |
| Error code: | SC819 |
| Description: | Fatal kernel error. Due to a control error, a RAM overflow occurred during system processing. One of the following messages was dis |
| Causes: | • Controller board defective |
| Remedy: | • System program defective • Controller board defective • Optional board defective • Replace controller firmware 0x696e init died 0x766d vm_pageout: Virtual Memory is full 4361 Cache Error NOTE: For more details about this SC code error, execute SP5990 to print an SMC report so you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | SC821 |
| Description: | Self-diagnostic error 1: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • ASIC (controller board defective) |
| Error code: | SC822 |
| Description: | Self-diagnostic error 2: HDD |
| Error code: | SC824 |
| Description: | Self-diagnostic error 4: NVRAM NVRAM device does not exist, NVRAM device is damaged, NVRAM socket damaged |
| Causes: | • Controller board detective |
| Remedy: | • NVRAM defective • Controller board defective • NVRAM backup battery exhausted • NVRAM socket damaged |
| Error code: | SC829 |
| Description: | Self-diagnostic error 5: Optional RAM Verify error for optional RAM. |
| Causes: | • Make sure that the resident RAM is installed in the correct slot. • Make sure the optional RAM is installed in the correct slot (Slot 0) |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the RAM DIMM. 3. Replace the controller board. |
| Error code: | SC833 |
| Description: | Self-diagnostic error 8: Engine I/F ASIC |
| Remedy: | 0F30 0F31 ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. • Replace the mother board 0F41 The read/write check done for resident RAM on the mother board could not be done correctly. • Replace the mother board 50B1 Could not initialize or read the bus connection. • Check for loose connections at the mother board. • Replace the mother board 50B2 Value of the SSCG register is incorrect. • Check for loose connections at the mother board. • Replace the mother board |
| Error code: | SC834 |
| Description: | Self-diagnostic error 9: Optional Memory RAM DIMM 5101 The write/verify check for the optional RAM chip on the engine mother board gave an error. |
| Causes: | • Controller defective |
| Remedy: | • Controller defective • Mother board defective |
| Error code: | SC850 |
| Description: | Net I/F error. • Duplicate IP addresses. • Illegal IP address. • Driver unstable and cannot be used on the network. |
| Causes: | • IP address setting incorrect • Ethernet board defective • Controller board defective |
| Remedy: | • IP address setting incorrect • Ethernet board defective • Controller board defective |
| Error code: | SC858 |
| Description: | SC858-00: Data Encryption Conversion Error (Key Acquisition Error) SC858-01: Data Encryption Conversion Error (HDD Key Setting Error) SC858-02: Data Encryption Conversion Error (NVRAM Read/Write Error) SC858-30: Data Encryption Conversion Error (NVRAM Before Conversion Error) SC858-31: Data Encryption Conversion Error (Other Errors) A serious error occurred after data conversion when updating the encryption key. |
| Causes: | • SC858-00, -01 • Data such as the USB Flash is corrupted. • A communication error is caused by electrostatic noise. • The controller board is defective. • SC858-02 The NVRAM is defective. • SC858-30 There is a software error (for example, the parameters used for conversion are invalid). • SC858-31 The controller board is defective. |
| Remedy: | • SC858-00, -31 Replace the controller board. • SC858-01, -30 Turn the main power OFF then ON. If the error persists, replace the controller board. • SC858-02 • Replace the NVRAM. • Replace the controller board. |
| Error code: | SC859 |
| Description: | SC859-00: Data Encryption Conversion HDD Conversion Error SC889-01: Data Encryption Conversion HDD Conversion Error (HDD Check Error) SC859-02: Data Encryption Conversion HDD Conversion Error (Power Failure During Conversion) SC859-10: Data Encryption Conversion HDD Conversion Error (Data Read/Write Command Error) • SC859-00, -01 When updating the data encryption key, HDD data was not converted correctly. During conversion, only the error screen is displayed and there is no SC. The SC is displayed after the machine is turned OFF and ON. • SC859-02 When updating the data encryption key, NVRAM/HDD conversion was incomplete. During conversion, only the error screen is displayed and there is no SC. The SC is displayed after the machine is turned OFF and ON. • SC859-10 When updating the data encryption key, an abnormal DMAC return value (such as DMAC time-out or serial communication error) was detected for two or more times. During data conversion, only the error screen is displayed and there is no SC. The SC is displayed after the machine is turned OFF and ON. |
| Causes: | • SC859-00, -01 • HDD conversion was specified for data encryption key update, but the HDD was removed. • Power was cut during data encryption key update. • There was a HDD error or electrostatic noise during data encryption key update. • SC859-02 Power was cut during data encryption key update. • SC859-10 There was a HDD error or electrostatic noise during data encryption key update. |
| Remedy: | • SC859-00, -01, -10 • Check the HDD connection. • Format the HDD. • If the HDD is defective, replace it. • SC859-02 After restart, a screen instructing the user to format the HDD is displayed. |
| Error code: | SC861 |
| Description: | HDD re-try failure. At power ON with the HDD detected, power supply to the HDD is interrupted, after the HDD is awakened from the sleep mode, the HDD is not ready within 30 s. |
| Causes: | At power on with the HDD detected, power supply to the HDD is interrupted, after the HDD is awakened from the sleep mode, the HDD is not ready within 30 s. |
| Remedy: | • Harness between HDD and board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | SC863 |
| Description: | HDD data read failure. The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Remedy: | • HDD defective Note: If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM, and the next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. |
| Error code: | SC864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to an CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | During HDD operation, the HDD cannot respond to an CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Remedy: | • HDD defective |
| Error code: | SC865 |
| Description: | HDD access error. HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Remedy: | • HDD defective. |
| Error code: | SC867 |
| Description: | SD card error 2: SD card removed. The SD card in the boot slot when the machine was turned on was removed while the machine was ON. |
| Causes: | An application SD card has been removed from the slot (mount point of /mnt/sd*). |
| Remedy: | • Insert the SD card, then turn the machine OFF and ON. |
| Error code: | SC868 |
| Description: | SD card error 3: SD card access. An error occurred while an SD card was used. |
| Causes: | • SD card defective • SD controller defective |
| Remedy: | • SD card not inserted correctly • SD card defective • Controller board defective Note: If you want to try to reformat the SD card, use SD Formatter Ver 1.1. |
| Error code: | SC870 |
| Description: | Address book data error. Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Software bug • Inconsistency of Address Book source location (machine/delivery server/LDAP server) • Inconsistency of Address Book encryption setting or encryption key (NVRAM was replaced individually without formatting the Address Book) • Address Book storage device (SD) was temporarily removed or hardware configuration does not match the application configuration. • Address Book data corruption was detected. |
| Remedy: | • Software defective. Turn the machine OFF/ON. If this is not the solution for the problem, then replace the controller firmware. • HDD defective. More Details • Do SP5846 050 (UCS (User info control service) Settings – Initialize all Directory Info.) to reset all address book data. • Reset the user information with SP5832 006 (HDD Formatting– User Information). • Replace the HDDs. • Boot the machine from the SD card. |
| Error code: | SC874 |
| Description: | Delete All error 1: HDD. A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit (B735) running from an SD card. |
| Causes: | • Error detected in HDD data delete program • Error detected in NVRAM data delete program • The "Delete All" option was not set |
| Remedy: | • Turn the main switch OFF/ON and try the operation again. • Install the Data Overwrite Security Unit again. For more, see section “1. Installation”. • HDD defective |
| Error code: | SC875 |
| Description: | Delete All error 2: Data area. An error occurred while the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B660 running from an SD card. |
| Causes: | • HDD logical formatting failed. • The modules failed to erase data. |
| Remedy: | • Turn the main switch OFF/ON and try the operation again. |
| Error code: | SC901 |
| Description: | Mechanical Counter 1 error Mechanical Counter 1 was not set correctly at power on, or the operator disconnected the counter while machine was operating. |
| Causes: | • Mechanical Counter 1 connection loose or defective • Mechanical Counter 1 defective |
| Error code: | SC902 |
| Description: | Mechanical Counter 2 error Mechanical Counter 2 was not set correctly at power on, or the operator disconnected the counter while machine was operating. |
| Remedy: | 1. Make sure the counter is connected properly. 2. Replace the total counter. [Signal Check] • Trigger line: CN230-B10 on the I/O control board • Counter OK signal: TP228 on the I/O control board |
| Error code: | SC910 … C914 |
| Description: | External controller error |
| Error code: | SC919 |
| Description: | External controller (E-7000) down. An internal application error was detected and operation cannot continue. |
| Causes: | While EAC (External Application Converter), the conversion module, was operating normally, the receipt of a power line interrupt signal from the FLUTE serial driver was detected, or BREAK signal from the other station was detected. |
| Remedy: | • Software defective; turn the machine OFF/ON, or change the controller firmware • Insufficient memory |
| Error code: | SC925 |
| Description: | Net File function error. The NetFile file management on the HDD cannot be used, or a NetFile management file is corrupted and operation cannot continue. The HDDs are defective and they cannot be debugged or partitioned, so the Scan Router functions (delivery of received faxes, document capture, etc.), Web services, and other network functions cannot be used. HDD status codes are displayed below: |
| Causes: | The NetFile file management on the HDD cannot be used, or a NetFile management file is corrupted and operation cannot continue. The HDDs are defective and they cannot be debugged or partitioned, so the Scan Router functions (delivery of received faxes, document capture, etc.), Web services, and other network functions cannot be used. HDD status codes are displayed below the SC code: |
| Remedy: | Procedure 1 If the machine shows SC codes for HDD errors (SC860 ~ SC865) with SC 925, do the recovery procedures for SC860 ~ SC865. Procedure 2 If the machine does not show one of the five HDD errors (SC860 ~ SC865), turn the machine power OFF and ON. If this is not the solution for the problem, then initialize the NetFile partition on the HDD with SP5832-011 (HDD Formatting). NetFiles: Jobs printed from the document server using a PC and DeskTopBinder • Before you initialize the NetFile partition on the HDD, tell the customer that: • Received faxes on the delivery server will be erased • All captured documents will be erased • DeskTopBinder job history will be erased • Documents on the document server, and scanned documents, will not be erased. • The first time that the network gets access to the machine, the management information must be configured again (this will use a lot of time). Before you initialize the Netfile partition with SP5832-011, do these steps: 1. Go into the User Tools mode and do “Delivery Settings” to print all received fax documents that are scheduled for delivery. Then erase them. 2. In the User Tools mode, do Document Management> Batch Delete Transfer Documents. 3. Do SP5832-011, then turn the machine power OFF and ON. Procedure 3 If “Procedure 2” is not the solution for the problem, do SP5832-001 (HDD Formatting – All), then turn the machine power OFF and ON. SP5832-001 erases all document and address book data on the hard disks. Ask the customer before you do this SP code. Procedure 4 If “Procedure 3” is not the solution for the problem, replace the HDD. |
Парткод
Название
RICOH TYPE K Скрепки с картриджем
RICOH TYPE K Скрепки (3 упаковки)
RICOH TYPE L Скрепки буклетные в картридже
RICOH TYPE L Скрепки буклетные (в упаковке 4*2000шт.)
RICOH TYPE M Скрепки в картридже
RICOH TYPE M Скрепки в картридже (5 шт.)
(841100) RICOH TYPE MPC7500E Тонер-картридж черный
(841101) RICOH TYPE MPC7500E Тонер-картридж голубой
(841102) RICOH TYPE MPC7500E Тонер-картридж пурпурный
(841103) RICOH TYPE MPC7500E Тонер-картридж желтый
RICOH TYPE 85 Скрепки (4 упаковки)
RICOH Блок фотобарабана
RICOH Девелопер черный
RICOH Девелопер голубой
RICOH Девелопер пурпурный
RICOH Девелопер желтый
