Ricoh MPW2401
Рейтинг
Модули
Charge & Transfer Unit
Drum Section
Frame 1
Scanner Section 1
FUSING UNIT 2
EXTERIOR 1
OPERATION PANEL
Paper Exit 2
DRIVE SECTION
ELECTRICAL SECTION 2
FUSING UNIT 1
Frame 2
PAPER REGISTRATION
SCANNER SECTION 2
Charge Cleaning Section
DEVELOPMENT UNIT
Paper Exit 1
ELECTRICAL SECTION 1
Scanner Section 4
SCANNER SECTION 3
ELECTRICAL SECTION 3
Image Prosessing
EXTERIOR 2
Детали ELECTRICAL SECTION 2
| Деталь: | T/S Corona Unit |
| Парткод: | B286 3830 |
| Деталь: | Sheet:Entrance:Transfer:Assy |
| Парткод: | B286 3855 |
| Деталь: | End Block Cover - T & S |
| Парткод: | AD02 2320 |
| Деталь: | Corona Wire Spring |
| Парткод: | AA06 6254 |
| Деталь: | End Block:T/S Corona:Left |
| Парткод: | AD02 2373 |
| Деталь: | End Block:T/S Corona:Right |
| Парткод: | AD02 2372 |
| Деталь: | Corona Wire - Main |
| Парткод: | AD02 0059 |
| Деталь: | Corona Wire - Separation |
| Парткод: | AD02 0072 |
| Деталь: | Left Paper Guide - T/S Outer |
| Парткод: | A174 3938 |
| Деталь: | Guide:Paper:T/S Corona:Middle:Left |
| Парткод: | A174 3932 |
| Деталь: | Guide:Paper:T/S Corona:Middle:Right |
| Парткод: | A174 3931 |
| Деталь: | Right Paper Guide - T/S Outer |
| Парткод: | A174 3937 |
| Деталь: | Shielding Plate:Harness |
| Парткод: | B125 3868 |
| Деталь: | CHARGE CORONA UNIT |
| Парткод: | AD00 4104 |
| Деталь: | Left End Block |
| Парткод: | AD02 2377 |
| Деталь: | Left Grid Terminal |
| Парткод: | A163 2052 |
| Деталь: | SPRING |
| Парткод: | AA06 0749 |
| Деталь: | Left End Block Cover - Charge |
| Парткод: | AD02 2317 |
| Деталь: | Charge Corona Wire - G |
| Парткод: | AD02 0089 |
| Деталь: | Grid Wire |
| Парткод: | AD02 0090 |
| Деталь: | Spring:Corona Wire:Charge |
| Парткод: | AA06 0965 |
| Деталь: | Cleaner:Slider |
| Парткод: | B125 2060 |
| Деталь: | Cleaner:Charge Corona |
| Парткод: | B125 2061 |
| Деталь: | End Block:Charge Corona:Right:Assy |
| Парткод: | AD02 2380 |
| Деталь: | Terminal:Grid:Right |
| Парткод: | B125 2018 |
| Деталь: | End Block Cover - Charge Corona |
| Парткод: | AD02 2369 |
| Деталь: | Left Holder - Charge Corona |
| Парткод: | B010 2062 |
| Деталь: | Right Holder - Charge Corona |
| Парткод: | B010 2061 |
| Деталь: | Flange:Timing Pulley |
| Парткод: | B286 1151 |
| Деталь: | Drum Stay |
| Парткод: | B286 1131 |
| Деталь: | Pulley:Tightener |
| Парткод: | B286 1146 |
| Деталь: | Timing Pulley:T102 |
| Парткод: | AB03 0812 |
| Деталь: | Timing Belt:135S2M426 |
| Парткод: | AA04 3655 |
| Деталь: | Holder:Ball Bearing |
| Парткод: | D093 2253 |
| Деталь: | Side Plate:Left |
| Парткод: | B286 3555 |
| Деталь: | Drum Right Shield |
| Парткод: | AA15 3135 |
| Деталь: | Blade Left Shield |
| Парткод: | AA15 3134 |
| Деталь: | Stopper:Ball Bearing |
| Парткод: | B188 2256 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Gear - 46Z |
| Парткод: | AB01 0364 |
| Деталь: | Rear Shutter Pin |
| Парткод: | AA14 3335 |
| Деталь: | C-ring:Drum Shaft |
| Парткод: | B125 2469 |
| Деталь: | Spring:Tightener:Drum |
| Парткод: | B286 1144 |
| Деталь: | Gear - 146Z |
| Парткод: | AB01 0363 |
| Деталь: | Shaft:Drum:Assy |
| Парткод: | D093 2300 |
| Деталь: | DRUM |
| Парткод: | B010 9510 |
| Деталь: | Balancer:OPC Drum |
| Парткод: | B125 2472 |
| Деталь: | Drum Flange |
| Парткод: | AD01 4030 |
| Деталь: | Compression Spring:Pressure:Drum |
| Парткод: | D093 2304 |
| Деталь: | Spacer:Compression Spring:Drum |
| Парткод: | B188 2255 |
| Деталь: | Drum Knob |
| Парткод: | A163 2251 |
| Деталь: | Harness - DC Cleaning Unit |
| Парткод: | B275 5692 |
| Деталь: | Density Sensor:Unit |
| Парткод: | B125 3580 |
| Деталь: | Stopper:Drum |
| Парткод: | D093 2303 |
| Деталь: | Casing:Pickoff Pawl |
| Парткод: | D093 3566 |
| Деталь: | DC Solenoid:Pickoff Pawl |
| Парткод: | AX10 0032 |
| Деталь: | Pick-off Pawl |
| Парткод: | A163 3611 |
| Деталь: | Screw:Lever:Release:Blade |
| Парткод: | B188 3575 |
| Деталь: | Lever:Release:Blade |
| Парткод: | B188 3582 |
| Деталь: | Left Pressure Lever |
| Парткод: | A163 3608 |
| Деталь: | LEVER SHAFT |
| Парткод: | A163 3609 |
| Деталь: | Right Pressure Lever |
| Парткод: | A163 3607 |
| Деталь: | Casing:Cleaning |
| Парткод: | B125 3563 |
| Деталь: | Toner Collection Coil:Cleaning |
| Парткод: | AD04 3085 |
| Деталь: | CLEANING BLADE |
| Парткод: | B286 3581 |
| Деталь: | Cleaning Blade Spring |
| Парткод: | AA06 2325 |
| Деталь: | Side Plate:Right |
| Парткод: | B125 3551 |
| Деталь: | Blade Right Shield |
| Парткод: | AA15 3133 |
| Деталь: | Toner Outlet Shutter Spring |
| Парткод: | AA06 6664 |
| Деталь: | Shutter:Discharge Used Toner |
| Парткод: | B125 3554 |
| Деталь: | Tightener |
| Парткод: | B286 1141 |
| Деталь: | Anchor:Cassette Sensor |
| Парткод: | AA14 3546 |
| Деталь: | Decal:Warning (High Temperature): Solenoid:Separation |
| Парткод: | D093 3569 |
| Деталь: | Knob:Lever |
| Парткод: | B125 1097 |
| Деталь: | Tension Spring - Right |
| Парткод: | AA06 2338 |
| Деталь: | Lever:Machine Or Copier:Left |
| Парткод: | B125 1095 |
| Деталь: | Lever:Machine Or Copier:Right |
| Парткод: | B125 1096 |
| Деталь: | Cam:Pressure Release:Fusing:Left |
| Парткод: | B125 4344 |
| Деталь: | Cam:Pressure Release:Fusing:Right |
| Парткод: | B125 4343 |
| Деталь: | Pin:Hinge |
| Парткод: | B125 1100 |
| Деталь: | Bracket:Contact Point:Outer:Left |
| Парткод: | B125 1091 |
| Деталь: | Bracket:Contact Point:Outer:Right |
| Парткод: | B125 1092 |
| Деталь: | Bracket:Contact Point:Inner:Left |
| Парткод: | B125 1093 |
| Деталь: | Bracket:Contact Point:Inner:Right |
| Парткод: | B125 1094 |
| Деталь: | GAS SPRING |
| Парткод: | B275 1086 |
| Деталь: | Shaft:Gas Spring:Upper |
| Парткод: | B125 1087 |
| Деталь: | Anchor:Gas Spring |
| Парткод: | B125 1088 |
| Деталь: | Stand:DOM |
| Парткод: | B286 1090 |
| Деталь: | Ground Plate:Exhaust |
| Парткод: | B125 4353 |
| Деталь: | Seal:Block Heat |
| Парткод: | AA15 2479 |
| Деталь: | Anchor:Cassette Sensor |
| Парткод: | AA14 3546 |
| Деталь: | Screw:Cleaning Felt |
| Парткод: | AA14 3844 |
| Деталь: | Decal:Warning (High Temperature):120C |
| Парткод: | D093 4425 |
| Деталь: | Bracket:Fix:Fusing Unit:Left |
| Парткод: | B125 1162 |
| Деталь: | Bracket:Fix:Fusing Unit:Right |
| Парткод: | B125 1161 |
| Деталь: | Shield:Duct:Inner |
| Парткод: | B286 1183 |
| Деталь: | Duct:Exhaust |
| Парткод: | B286 1003 |
| Деталь: | Bracket:Cover:Lower:2 |
| Парткод: | B125 1264 |
| Деталь: | Bracket:Cover:Lower |
| Парткод: | B125 1261 |
| Деталь: | Sheet:Lgd |
| Парткод: | B125 1267 |
| Деталь: | Slider:Collection Bottle:Lower |
| Парткод: | B286 3583 |
| Деталь: | SEPARATION ROLLER |
| Парткод: | A163 4347 |
| Деталь: | Bracket:Roller |
| Парткод: | B125 4351 |
| Деталь: | Roller:Separation:Small |
| Парткод: | B125 4359 |
| Деталь: | SCREW |
| Парткод: | AA14 3855 |
| Деталь: | Guard Burring |
| Парткод: | B275 1670 |
| Деталь: | Guide:Bracket:Roller |
| Парткод: | B125 4352 |
| Деталь: | Cover:Thermostat |
| Парткод: | B286 1098 |
| Деталь: | Cover:Harness:Fusing |
| Парткод: | D093 1103 |
| Деталь: | TAPPING SCREW |
| Парткод: | AA14 3823 |
| Деталь: | Bracket:Pressure Plate:Left |
| Парткод: | B286 4966 |
| Деталь: | Cover:Original:Drive |
| Парткод: | B125 4809 |
| Деталь: | Bracket:Pressure Plate:Right |
| Парткод: | B286 4967 |
| Деталь: | Ground Wire:Pressure Plate |
| Парткод: | B125 5683 |
| Деталь: | Spring - 10n |
| Парткод: | AA06 3419 |
| Деталь: | Case:Spring |
| Парткод: | B125 4852 |
| Деталь: | Plate:Spring |
| Парткод: | B125 4853 |
| Деталь: | Pressure plate |
| Парткод: | B286 4940 |
| Деталь: | Supporting Plate:Cover:Original |
| Парткод: | B125 4742 |
| Деталь: | Square bushing |
| Парткод: | H004 3755 |
| Деталь: | Gasket:UC-300281:50mm |
| Парткод: | B286 5750 |
| Деталь: | Pin - 3x26mm |
| Парткод: | A422 1356 |
| Деталь: | Stopper:Original:Upper |
| Парткод: | B125 4732 |
| Деталь: | Spring:Stopper:Original |
| Парткод: | AA06 3444 |
| Деталь: | Original Table Bushing |
| Парткод: | A163 6052 |
| Деталь: | Shaft:Contact Point:Original:Upper |
| Парткод: | B125 4761 |
| Деталь: | Sheet:Block Light:CIS:Left |
| Парткод: | D093 4717 |
| Деталь: | Decal:Original:Operate:Multi-language:EXP |
| Парткод: | D093 4885 |
| Деталь: | Cover:Original:Switch |
| Парткод: | B125 4884 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0022 |
| Деталь: | Cushion:Keytop:Original:Stop |
| Парткод: | B286 4854 |
| Деталь: | Keytop:Original:Stop |
| Парткод: | B286 4767 |
| Деталь: | Ground Wire:Scanner Unit:Right |
| Парткод: | D093 5756 |
| Деталь: | Sheet:Block Light:CIS:Right |
| Парткод: | D093 4718 |
| Деталь: | Upper Pressure Release Lever |
| Парткод: | A163 4183 |
| Деталь: | Shaft:Lever:Pressure Release |
| Парткод: | B125 4174 |
| Деталь: | Harness:AC:Fusing:Connecting:1 |
| Парткод: | B125 5602 |
| Деталь: | Electrode Plate:Thermostat |
| Парткод: | B125 4156 |
| Деталь: | Thermostat Housing |
| Парткод: | B104 4084 |
| Деталь: | Stay:Fusing:Upper:Assy |
| Парткод: | B286 4151 |
| Деталь: | Fusing Thermistor |
| Парткод: | AW10 0087 |
| Деталь: | Plate- Thermistor |
| Парткод: | B004 4087 |
| Деталь: | Thermostat - 199C 250V/10A |
| Парткод: | AW11 0053 |
| Деталь: | Thermostat - 200C 250V/10A |
| Парткод: | AW11 0054 |
| Деталь: | Harness:AC:Fusing:Connect:120V |
| Парткод: | B125 5606 |
| Деталь: | Harness:AC:Fusing:Connect:220/230V |
| Парткод: | B125 5607 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | B286 4180 |
| Деталь: | Entrance Guide Plate Holder |
| Парткод: | A163 4122 |
| Деталь: | Holder Cam |
| Парткод: | A163 4124 |
| Деталь: | Sheet:Fusing:Small |
| Парткод: | B125 1269 |
| Деталь: | Sheet:Fusing:Large |
| Парткод: | B125 1271 |
| Деталь: | Bracket:Thermistor |
| Парткод: | B125 4162 |
| Деталь: | Thermistor - Rear |
| Парткод: | AW10 0053 |
| Деталь: | Cover - Housing Thermostat |
| Парткод: | B104 4086 |
| Деталь: | Side Plate:Fusing:Left |
| Парткод: | B286 4115 |
| Деталь: | Side Plate:Fusing:Right |
| Парткод: | B286 4105 |
| Деталь: | Stay:Lower:Fusing |
| Парткод: | B286 4163 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Harness:DC:Fusing:Sensor |
| Парткод: | B286 5702 |
| Деталь: | Side Fence:Left |
| Парткод: | B125 4720 |
| Деталь: | Side Fence:Right |
| Парткод: | B125 4723 |
| Деталь: | MANUAL FEED TABLE |
| Парткод: | B286 2594 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Cover - Toner Cartridge |
| Парткод: | B286 4806 |
| Деталь: | Decal:Emblem:RIC (D093) |
| Парткод: | D093 4811 |
| Деталь: | Decal:Emblem:RIC (D094) |
| Парткод: | D094 4811 |
| Деталь: | Cover Sheet - Toner Cartridge |
| Парткод: | B125 4841 |
| Деталь: | Ground Plate- Toner Supply |
| Парткод: | G180 1265 |
| Деталь: | Decal:Original:Operate:Multi-language:EXP |
| Парткод: | D093 4885 |
| Деталь: | Decal:Original:Operate:Multi-language:CHN |
| Парткод: | D093 4887 |
| Деталь: | Cover:Left Upper |
| Парткод: | B286 1286 |
| Деталь: | Cover:Left Lower |
| Парткод: | B286 1287 |
| Деталь: | Decal:H-temp Warning:Exterior: Multi-language |
| Парткод: | D093 1265 |
| Деталь: | Cover:Right Upper |
| Парткод: | B125 1283 |
| Деталь: | Cover:Right Lower |
| Парткод: | B125 1288 |
| Деталь: | Guide:Original |
| Парткод: | B125 1363 |
| Деталь: | Guide Plate:Guide:Original |
| Парткод: | B125 1364 |
| Деталь: | Copy Tray:Upper |
| Парткод: | B286 1352 |
| Деталь: | Copy Tray:Auxiliary |
| Парткод: | D093 4462 |
| Деталь: | Guide:Original:Middle |
| Парткод: | B125 1358 |
| Деталь: | Operating Instructions Holder |
| Парткод: | B010 1359 |
| Деталь: | Decal:Left And Right:Copy Tray |
| Парткод: | D093 4464 |
| Деталь: | Guide:Paper:Auxiliary |
| Парткод: | D093 4470 |
| Деталь: | Cloth - DF Exposure Glass |
| Парткод: | B065 1374 |
| Деталь: | Case:Guide:Copy Tray |
| Парткод: | D093 4467 |
| Деталь: | Manual:TROUBLESHOOT:NA |
| Парткод: | D094 7523 |
| Деталь: | Manual:Troubleshoot:CN |
| Парткод: | D094 7696 |
| Деталь: | Manual:About_machine:NA |
| Парткод: | D094 7505 |
| Деталь: | Manual:About_Machine:CN |
| Парткод: | D094 7693 |
| Деталь: | Panel:Logo |
| Парткод: | B132 1531 |
| Деталь: | Holder:Original Tray |
| Парткод: | B286 1382 |
| Деталь: | Spring:Original Tray |
| Парткод: | AA06 6681 |
| Деталь: | Original Tray |
| Парткод: | B286 1380 |
| Деталь: | Decal:Power Source:Off:English |
| Парткод: | GA00 0067 |
| Деталь: | Decal - Power Source Off(CHN) |
| Парткод: | B188 1373 |
| Деталь: | Gasket:EGUN10313:L35 |
| Парткод: | D093 5321 |
| Деталь: | Gasket:EGUN10710:L35 |
| Парткод: | D093 5322 |
| Деталь: | CD-ROM:OI:User:NA:Assy |
| Парткод: | D093 7703 |
| Деталь: | CD-ROM:Drv/Man:User:CHN:Assy |
| Парткод: | D093 7707 |
| Деталь: | CD-ROM:Drv/Man:Admin:CHN:Assy |
| Парткод: | D093 7709 |
| Деталь: | Cloth Holder |
| Парткод: | B065 1371 |
| Деталь: | Guide Plate:Brush |
| Парткод: | B125 1355 |
| Деталь: | Sheet:Quick_Ref_Copy:CHN |
| Парткод: | D094 7719 |
| Деталь: | Sheet:Quick_Ref_Prin:CHN |
| Парткод: | D094 7739 |
| Деталь: | Sheet:Quick_Ref_Scan:CH |
| Парткод: | D094 7759 |
| Деталь: | Operation Sub-unit:NA |
| Парткод: | D093 1441 |
| Деталь: | Operation Sub-unit:EU/AA |
| Парткод: | D093 1442 |
| Деталь: | Operation Sub-unit:CHN |
| Парткод: | D093 1443 |
| Деталь: | Keytop - Blank FB |
| Парткод: | B223 1518 |
| Деталь: | Keytop - Doc NA |
| Парткод: | B223 1529 |
| Деталь: | Keytop:Doc:EU |
| Парткод: | B223 1535 |
| Деталь: | Keytop - Copy NA |
| Парткод: | B223 1528 |
| Деталь: | Keytop:Copy:EU |
| Парткод: | B223 1534 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B223 1520 |
| Деталь: | Keytop:10key:NA |
| Парткод: | B223 1540 |
| Деталь: | Keytop:10key |
| Парткод: | B223 1521 |
| Деталь: | Keytop - Clear Modes |
| Парткод: | B238 1583 |
| Деталь: | Keytop - Start |
| Парткод: | B238 1504 |
| Деталь: | Keytop - Try Print |
| Парткод: | B238 1506 |
| Деталь: | Keytop - Interrupt |
| Парткод: | B238 1509 |
| Деталь: | Keytop - Kantan |
| Парткод: | B238 1552 |
| Деталь: | Keytop - Login |
| Парткод: | B238 1550 |
| Деталь: | Keytop - Power Source |
| Парткод: | B238 1549 |
| Деталь: | PCB:ALC1:OP-R:Sub-assy |
| Парткод: | D009 1466 |
| Деталь: | PCB:NPC2:OP-L:Sub-Assy |
| Парткод: | B286 1497 |
| Деталь: | Harness:OP-R:13 |
| Парткод: | D009 1481 |
| Деталь: | Harness:OP-R:10 |
| Парткод: | D009 1480 |
| Деталь: | Spacer - Keytop |
| Парткод: | B238 1547 |
| Деталь: | Invertor:TFT |
| Парткод: | D009 1486 |
| Деталь: | Harness:Invertor |
| Парткод: | D009 1484 |
| Деталь: | PCB:LCDC:NA |
| Парткод: | D093 1431 |
| Деталь: | PCB:LCDC:EU |
| Парткод: | D093 1432 |
| Деталь: | PCB:LCDC:CHN |
| Парткод: | D093 1433 |
| Деталь: | Cable:FFC:TFT:LCD |
| Парткод: | D009 1487 |
| Деталь: | Keytop - Counter |
| Парткод: | B238 1511 |
| Деталь: | Bracket:LCDC:BLG-C1:Assy |
| Парткод: | D046 1475 |
| Деталь: | Shadeing Plate:Touch Panel:Assy |
| Парткод: | D029 1507 |
| Деталь: | Touch Panel:WVGA:FU-ACF |
| Парткод: | D029 1484 |
| Деталь: | LCD Spacer B |
| Парткод: | B238 1535 |
| Деталь: | LCD Spacer A |
| Парткод: | B238 1534 |
| Деталь: | LCD:TFT:W-VGA:SH |
| Парткод: | D009 1489 |
| Деталь: | Harness:BLG:OP-L:13 |
| Парткод: | D046 1466 |
| Деталь: | Harness:BLG:OP-L:12 |
| Парткод: | D046 1465 |
| Деталь: | Lens:Front:BLG-C1 |
| Парткод: | D046 1474 |
| Деталь: | Panel:Upper:NA |
| Парткод: | D009 1556 |
| Деталь: | Panel:Upper:EU |
| Парткод: | D009 1557 |
| Деталь: | Sheet:Power Source:Display:NA |
| Парткод: | B238 1539 |
| Деталь: | Sheet:Power Source:N-C2:EU |
| Парткод: | B286 1479 |
| Деталь: | Paper Exit Unit:Assy |
| Парткод: | D093 4452 |
| Деталь: | Decal - Grip |
| Парткод: | AA00 3210 |
| Деталь: | Gasket:Guide Plate:Exit |
| Парткод: | B286 4471 |
| Деталь: | Bracket:Lock:Right |
| Парткод: | B286 4455 |
| Деталь: | Positioning Plate:Exit |
| Парткод: | B125 4456 |
| Деталь: | Development Cover Screw |
| Парткод: | AA14 3810 |
| Деталь: | Spring - Timing Belt Tension |
| Парткод: | AA06 2337 |
| Деталь: | Cover:Exit |
| Парткод: | B286 4451 |
| Деталь: | Exit Driven Roller |
| Парткод: | A163 4453 |
| Деталь: | Leaf Spring:Exit Roller:Upper |
| Парткод: | B125 4452 |
| Деталь: | Leaf Spring:Exit Roller:Lower |
| Парткод: | B125 4453 |
| Деталь: | Bracket:Lock:Exit:Left |
| Парткод: | B125 4460 |
| Деталь: | Ground Wire:Paper Exit Unit |
| Парткод: | B188 4461 |
| Деталь: | Ground Wire:Scanner Unit:3 |
| Парткод: | B125 5643 |
| Деталь: | Gate Pawl Drive |
| Парткод: | A174 4372 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Guide Plate:Exit |
| Парткод: | B125 4458 |
| Деталь: | Stay:Exit |
| Парткод: | B125 4462 |
| Деталь: | Ground Wire:Paper Exit Unit |
| Парткод: | B286 5739 |
| Деталь: | Gate Pawl Plate |
| Парткод: | B010 4458 |
| Деталь: | Exit Separation Pawl |
| Парткод: | AF02 5029 |
| Деталь: | Spring:Pressure Release |
| Парткод: | AA06 6366 |
| Деталь: | DC Solenoid:Gate Pawl |
| Парткод: | B286 4463 |
| Деталь: | Positioning Pin |
| Парткод: | AA14 3859 |
| Деталь: | Stud - M4 |
| Парткод: | 59 183 120 |
| Деталь: | Tension Spring:2.16N |
| Парткод: | AA06 2333 |
| Деталь: | Tightener:Fusing |
| Парткод: | B125 1136 |
| Деталь: | Tightener - M16 |
| Парткод: | G568 2839 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Timing Belt:60S3M471 |
| Парткод: | AA04 3654 |
| Деталь: | Gear/Pulley - 30Z/63T |
| Парткод: | AB01 7675 |
| Деталь: | Pulley Flange |
| Парткод: | A259 1158 |
| Деталь: | Gear:Timing Pulley:Z83/T20 |
| Парткод: | AB01 7740 |
| Деталь: | Cover:Gear:Development |
| Парткод: | D093 1296 |
| Деталь: | Gear:Z112/Z19 |
| Парткод: | AB01 7739 |
| Деталь: | Timing Pulley:Gear:T70/Z40 |
| Парткод: | AB01 7738 |
| Деталь: | Timing Belt - B60S2M214 |
| Парткод: | AA04 3644 |
| Деталь: | Gear:Z28 |
| Парткод: | AB01 2049 |
| Деталь: | Arm:Coupling:Development |
| Парткод: | B125 1146 |
| Деталь: | Shaft:Coupling:Development |
| Парткод: | B125 1147 |
| Деталь: | Spring:Pressure Release |
| Парткод: | AA06 0969 |
| Деталь: | Gear:Z50:Assy |
| Парткод: | AB01 2052 |
| Деталь: | Gear - 46Z |
| Парткод: | AB01 4267 |
| Деталь: | Tightener |
| Парткод: | G020 4444 |
| Деталь: | Tightener:Development |
| Парткод: | B125 1125 |
| Деталь: | Spring:Blade:Cleaning |
| Парткод: | AA06 1006 |
| Деталь: | Gear:Z61/Z30:Assy |
| Парткод: | D093 3102 |
| Деталь: | Timing Belt:100S2M260 |
| Парткод: | AA04 3653 |
| Деталь: | Timing Pulley:T64/Z19:Assy |
| Парткод: | D093 3100 |
| Деталь: | PULLEY |
| Парткод: | A548 2139 |
| Деталь: | Tightener:Registration |
| Парткод: | B125 1130 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 1011 |
| Деталь: | Bracket:Cover:Lower |
| Парткод: | B125 1261 |
| Деталь: | Brushless Motor:DC24V 24W:Z9 |
| Парткод: | AX06 0296 |
| Деталь: | Magnetic clutch |
| Парткод: | AX21 0099 |
| Деталь: | Brushless Motor DC24V 45W |
| Парткод: | AX06 0334 |
| Деталь: | Side Plate:Drive |
| Парткод: | B286 1101 |
| Деталь: | Stopper Screw - M3 |
| Парткод: | 58 403 022 |
| Деталь: | Cover:Fusing:Upper |
| Парткод: | D093 4282 |
| Деталь: | Decal:Original:Operate:Multi-language:EXP |
| Парткод: | D093 4885 |
| Деталь: | Decal - Grip |
| Парткод: | AA00 3210 |
| Деталь: | Shield:Cover:Fusing:Harness |
| Парткод: | B286 4285 |
| Деталь: | Harness:DC:Exhaust:Connecting |
| Парткод: | D093 5752 |
| Деталь: | Ozone Filter:Exhaust |
| Парткод: | AA01 0124 |
| Деталь: | Fan Motor DC24V 8.5W |
| Парткод: | B286 4293 |
| Деталь: | Guide Plate:Duct |
| Парткод: | B125 4298 |
| Деталь: | Seal - Fan Harness |
| Парткод: | A134 1195 |
| Деталь: | Shield:Front:Guide Plate:Duct |
| Парткод: | B286 4292 |
| Деталь: | Duct:Louver |
| Парткод: | B125 4283 |
| Деталь: | Harness:High Voltage:Transfer |
| Парткод: | B286 5713 |
| Деталь: | Harness:High Voltage:Separation |
| Парткод: | B286 5712 |
| Деталь: | Power Pack TD |
| Парткод: | AZ32 0150 |
| Деталь: | Bracket:Power Pack |
| Парткод: | B125 1171 |
| Деталь: | Harness:AC:Main |
| Парткод: | D093 5712 |
| Деталь: | Harness:AC:Fusing:NA |
| Парткод: | D093 5758 |
| Деталь: | Harness:AC:Fusing:230V |
| Парткод: | D093 5759 |
| Деталь: | Power Supply Unit:DOM/NA |
| Парткод: | AZ23 0246 |
| Деталь: | Power Supply Unit:EU/AA/CHN |
| Парткод: | AZ23 0247 |
| Деталь: | Fan:MM60 |
| Парткод: | AX64 0207 |
| Деталь: | Cover:Harness Clamp |
| Парткод: | B125 1057 |
| Деталь: | Ground Plate:Fusing |
| Парткод: | D093 4360 |
| Деталь: | Bracket:Rocker Switch |
| Парткод: | D093 5327 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Decal:H-temp Warning:Fusing Exit Section: Outer |
| Парткод: | D093 4451 |
| Деталь: | Fusing Unit:NA:Assy |
| Парткод: | D093 4006 |
| Деталь: | Fusing Unit:EU/AA:Assy |
| Парткод: | D093 4007 |
| Деталь: | Cover:Heater:Left |
| Парткод: | B286 4137 |
| Деталь: | Development Cover Screw |
| Парткод: | AA14 3810 |
| Деталь: | Lever:Pressure |
| Парткод: | B125 4172 |
| Деталь: | Spring - Pressure |
| Парткод: | AA06 2340 |
| Деталь: | C-ring:MM50 |
| Парткод: | B125 4130 |
| Деталь: | Gear:Drive:Fusing |
| Парткод: | AB01 4268 |
| Деталь: | Bushing - Fusing |
| Парткод: | AE03 1056 |
| Деталь: | Cover:Heater |
| Парткод: | B286 4139 |
| Деталь: | Bracket:Heater:Left |
| Парткод: | B286 4133 |
| Деталь: | Cushion:Heater:Fusing |
| Парткод: | D093 4096 |
| Деталь: | Lever:Pressure Release:Lower |
| Парткод: | B125 4173 |
| Деталь: | Heater:120V:1150W |
| Парткод: | AX45 0042 |
| Деталь: | Heater:230V:1150W |
| Парткод: | AX45 0043 |
| Деталь: | Hot Roller |
| Парткод: | AE01 1122 |
| Деталь: | Holder:Pressure Roller |
| Парткод: | B286 4148 |
| Деталь: | C - Ring - 19m |
| Парткод: | A163 4109 |
| Деталь: | Ball Bearing - 20x32x7 |
| Парткод: | AE03 0050 |
| Деталь: | Pressure Roller:MM55 |
| Парткод: | AE02 0148 |
| Деталь: | Shaft:Pressure Roller |
| Парткод: | B125 4145 |
| Деталь: | Guide Plate:Fusing Exit:Lower |
| Парткод: | B125 4194 |
| Деталь: | Guide:Auxiliary:Fusing Exit |
| Парткод: | B125 4195 |
| Деталь: | Pressure Roller Pickoff Pawl |
| Парткод: | AE04 4055 |
| Деталь: | Pressure Roller Pickoff Pawl Spring |
| Парткод: | AA06 0942 |
| Деталь: | Cover:Harness:Fusing:Left |
| Парткод: | D093 4371 |
| Деталь: | Fusing Cover:Upper |
| Парткод: | B286 4211 |
| Деталь: | Heat Insulation:Cover:Fusing |
| Парткод: | D093 4373 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0127 |
| Деталь: | SCREW |
| Парткод: | AA14 3854 |
| Деталь: | Arm:Cleaning Roller:Left |
| Парткод: | B286 4214 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Fusing Cleaning Roller |
| Парткод: | AE04 2047 |
| Деталь: | Roller Clutch - 6x14x10 |
| Парткод: | AA08 3016 |
| Деталь: | Arm:Cleaning Roller:Right |
| Парткод: | B286 4213 |
| Деталь: | Bracket:Heater:Right |
| Парткод: | B286 4132 |
| Деталь: | Discharge Brush:Fusing |
| Парткод: | AA12 0127 |
| Деталь: | Cover:Harness:Fusing:Right |
| Парткод: | D093 4372 |
| Деталь: | Cover:Middle:Interface |
| Парткод: | D093 1259 |
| Деталь: | Decal:Original:Operate:Multi-language:EXP |
| Парткод: | D093 4885 |
| Деталь: | Cover:Control Board:Usb |
| Парткод: | D093 5317 |
| Деталь: | Cover:Harness |
| Парткод: | D093 5307 |
| Деталь: | Power Supply Cord - 120V |
| Парткод: | B286 5767 |
| Деталь: | Power Supply Cord - 220V |
| Парткод: | B286 5765 |
| Деталь: | Power Supply Cord (230V)(CHN) |
| Парткод: | B275 5890 |
| Деталь: | Bracket:Power Supply Cord |
| Парткод: | B125 1170 |
| Деталь: | Bracket:Leak Breaker |
| Парткод: | D093 5326 |
| Деталь: | Harness:AC:Leak Breaker |
| Парткод: | D093 5757 |
| Деталь: | Total Counter:7FIG:24V |
| Парткод: | AX31 0045 |
| Деталь: | Cover:Interface |
| Парткод: | B286 1260 |
| Деталь: | Rail:Right |
| Парткод: | G133 5795 |
| Деталь: | Rail:Left |
| Парткод: | G133 5796 |
| Деталь: | PCB:PC4200:RAWCard-A:1GB |
| Парткод: | G178 6072 |
| Деталь: | PCB:CTL:EX1 |
| Парткод: | D093 5681 |
| Деталь: | Cable:HDD:SATA:RED:170 |
| Парткод: | D029 5371 |
| Деталь: | Cable:HDD:SATA:Power:140 |
| Парткод: | D029 5370 |
| Деталь: | Cover:Connector:EFI |
| Парткод: | D014 5974 |
| Деталь: | PCB:NOVITA-S5K |
| Парткод: | D093 9590 |
| Деталь: | Grounding Plate - Upper Rear |
| Парткод: | A267 1089 |
| Деталь: | HDD:WD:160GB:63N9A0 |
| Парткод: | D029 5792 |
| Деталь: | Screw:M3x4.2 |
| Парткод: | AA14 3548 |
| Деталь: | Bracket:HDD |
| Парткод: | D093 5308 |
| Деталь: | Rubber Cushion |
| Парткод: | AA16 1125 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3404 |
| Деталь: | Interface Panel |
| Парткод: | B101 5993 |
| Деталь: | Cover:SD-Card |
| Парткод: | D093 5309 |
| Деталь: | Guard Burring |
| Парткод: | B275 1670 |
| Деталь: | Tray:GW/HDD:Peen |
| Парткод: | D093 5310 |
| Деталь: | Large Drum Stay Ground Plate |
| Парткод: | B070 6877 |
| Деталь: | SD-Card:Z-V4:EXP |
| Парткод: | D093 6007 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Guide Plate:Lower |
| Парткод: | B125 2571 |
| Деталь: | Sheet:Manual Feed:Left And Right |
| Парткод: | B125 2585 |
| Деталь: | Sheet:Manual Feed:Middle |
| Парткод: | B125 2584 |
| Деталь: | Guide Plate:Manual Feed |
| Парткод: | B125 2572 |
| Деталь: | Registration Roller |
| Парткод: | AF02 0599 |
| Деталь: | Gasket:Registration:Guide Plate |
| Парткод: | B286 5769 |
| Деталь: | Guide Plate:Registration:Upper |
| Парткод: | B125 2575 |
| Деталь: | Gasket:20mm |
| Парткод: | D002 5688 |
| Деталь: | Registration Compression Spring |
| Парткод: | AA06 3900 |
| Деталь: | Bushing - Dia4 |
| Парткод: | AA08 2135 |
| Деталь: | Transport Driven Roller |
| Парткод: | AF02 2128 |
| Деталь: | Harness - DC Registration Sensor |
| Парткод: | B275 5693 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0180 |
| Деталь: | Bracket:Sensor |
| Парткод: | B125 2581 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Spring:9.8n |
| Парткод: | AA06 3427 |
| Деталь: | Bushing - Upper Registration Roller |
| Парткод: | 54 422 751 |
| Деталь: | Middle Driven Roller |
| Парткод: | AF02 0603 |
| Деталь: | FEELER SPRING |
| Парткод: | AA06 6255 |
| Деталь: | Feeler:Registration Sensor |
| Парткод: | B125 2579 |
| Деталь: | Holder:Feeler |
| Парткод: | B125 2580 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A222 2680 |
| Деталь: | Magnetic:Development Unit:Lower:Assy |
| Парткод: | D093 3181 |
| Деталь: | Harness:DC:Operation |
| Парткод: | B286 5763 |
| Деталь: | Stand:Pressure Release:Left |
| Парткод: | B125 4870 |
| Деталь: | Guard |
| Парткод: | H072 2207 |
| Деталь: | Stepped Screw - M3x10 |
| Парткод: | AA14 3394 |
| Деталь: | Knob:Pressure Release |
| Парткод: | B125 4864 |
| Деталь: | Screw:M4:Dia6x1.7:Black |
| Парткод: | AA14 3543 |
| Деталь: | Bracket:Pressure Release |
| Парткод: | B125 4866 |
| Деталь: | Left Pressure Release Spring - 5n |
| Парткод: | AA06 6370 |
| Деталь: | SCREW |
| Парткод: | AA14 3569 |
| Деталь: | Right Pressure Release Spring - 5n |
| Парткод: | AA06 6371 |
| Деталь: | Stand:Pressure Release:Right |
| Парткод: | B125 4871 |
| Деталь: | Spring - 3.4n |
| Парткод: | AA06 3416 |
| Деталь: | Bushing - Dia4 |
| Парткод: | AA08 2135 |
| Деталь: | Shaft:Driven |
| Парткод: | B125 4751 |
| Деталь: | Roller:Driven:Assy |
| Парткод: | D093 4772 |
| Деталь: | Driven Roller:Original Insert |
| Парткод: | B286 4752 |
| Деталь: | Spring:Driven:1.7N |
| Парткод: | AA06 3955 |
| Деталь: | Driven Roller:Assy |
| Парткод: | D093 4734 |
| Деталь: | Stopper:Open And Close:Left:Unit |
| Парткод: | B125 4901 |
| Деталь: | Shaft:Spring:Stopper |
| Парткод: | B125 4913 |
| Деталь: | Bracket:Open And Close:Stopper:Left |
| Парткод: | B125 4902 |
| Деталь: | Tension Spring:Stopper |
| Парткод: | B125 4910 |
| Деталь: | Shaft:Contact Point:Stopper |
| Парткод: | B125 4912 |
| Деталь: | Stopper:Open And Close:Left |
| Парткод: | B125 4904 |
| Деталь: | Stopper:Open And Close:Right:Unit |
| Парткод: | B125 4906 |
| Деталь: | Bracket:Open And Close:Stopper:Right |
| Парткод: | B125 4907 |
| Деталь: | Stopper:Open And Close:Right |
| Парткод: | B125 4909 |
| Деталь: | Sheet:Original Insert:A |
| Парткод: | B286 4757 |
| Деталь: | Sheet:Original Insert:B |
| Парткод: | B286 4758 |
| Деталь: | Sheet:Block Light:1 |
| Парткод: | B125 4825 |
| Деталь: | Sheet:Block Light:2 |
| Парткод: | B125 4826 |
| Деталь: | Sheet:Block Light:3 |
| Парткод: | B125 4827 |
| Деталь: | Sheet:Block Light:4 |
| Парткод: | B125 4828 |
| Деталь: | Sheet:Block Light:5 |
| Парткод: | B125 4829 |
| Деталь: | Sheet:Shield:Paper Size Sensor |
| Парткод: | B125 4879 |
| Деталь: | Cover:Original:Upper |
| Парткод: | B125 4725 |
| Деталь: | Cushion:Stepper Motor:47 |
| Парткод: | D093 4677 |
| Деталь: | Stepper Motor:Press Fit |
| Парткод: | D093 4771 |
| Деталь: | Harness - DC Charge 1 |
| Парткод: | B275 5657 |
| Деталь: | Shielding Plate:Charge Corona |
| Парткод: | B125 2130 |
| Деталь: | Stepped Screw:M3x10.3 |
| Парткод: | AA14 3786 |
| Деталь: | Stepped Screw:M3x14.2 |
| Парткод: | AA14 3787 |
| Деталь: | Pulley:Left |
| Парткод: | AB03 2723 |
| Деталь: | Pulley:Encoder |
| Парткод: | AB03 2724 |
| Деталь: | Gear:Pulley:Right |
| Парткод: | AB01 7664 |
| Деталь: | Wire:Cleaner |
| Парткод: | AA05 0113 |
| Деталь: | Tension Spring:4291mn |
| Парткод: | B125 2085 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | BRACKET |
| Парткод: | B125 2070 |
| Деталь: | Discharge Lamp:P2 |
| Парткод: | AX50 0099 |
| Деталь: | Harness - DC QL |
| Парткод: | B275 5690 |
| Деталь: | Guard:Spring Plate:Left |
| Парткод: | B125 2125 |
| Деталь: | Spring Plate:Charge Corona:Left |
| Парткод: | B125 2124 |
| Деталь: | Spring Plate:Earth |
| Парткод: | B125 2106 |
| Деталь: | Spring Plate:Charge Corona:Right |
| Парткод: | B125 2127 |
| Деталь: | Guard:Spring Plate:Right |
| Парткод: | B125 2128 |
| Деталь: | DC Motor:Cleaner:0.5W |
| Парткод: | AX04 0147 |
| Деталь: | Shield:Block Light |
| Парткод: | B286 4755 |
| Деталь: | Bushing:Arm:Rear |
| Парткод: | B125 4697 |
| Деталь: | Grounding Plate:Original:Rear Lower |
| Парткод: | B125 4754 |
| Деталь: | Guard:Grounding Plate:Rear |
| Парткод: | B125 4756 |
| Деталь: | Holder:Wire |
| Парткод: | B125 2113 |
| Деталь: | Spring:Corona Wire:Charge |
| Парткод: | AA06 0965 |
| Деталь: | Washer - DIA3 |
| Парткод: | B275 2036 |
| Деталь: | Development Unit |
| Парткод: | D093 3006 |
| Деталь: | Developer Type 30W Black |
| Парткод: | B125 9640 |
| Деталь: | Development Sleeve Gear |
| Парткод: | A174 1163 |
| Деталь: | Bearing Case:DIA26 |
| Парткод: | AA08 4057 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 3921 |
| Деталь: | Bushing:DIA6 |
| Парткод: | AA08 0336 |
| Деталь: | Auger Gear |
| Парткод: | A174 1164 |
| Деталь: | Paddle Gear |
| Парткод: | A174 1167 |
| Деталь: | Bearing Case |
| Парткод: | B125 3233 |
| Деталь: | Idle Gear - 28Z |
| Парткод: | A174 1162 |
| Деталь: | Shaft Holder - Pick-up Roller |
| Парткод: | 54 466 214 |
| Деталь: | Stay:Toner Hopper |
| Парткод: | B125 3205 |
| Деталь: | Spring Clutch:Toner Hopper |
| Парткод: | AX20 0272 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Left Shield - Side Plate |
| Парткод: | AA15 3451 |
| Деталь: | Right Shield - Side Plate |
| Парткод: | AA15 3450 |
| Деталь: | Filter Bracket |
| Парткод: | B188 3101 |
| Деталь: | Development Filter |
| Парткод: | AA01 2081 |
| Деталь: | Entrance Seal:Assy |
| Парткод: | D093 3150 |
| Деталь: | Bracket:Positioning:Left |
| Парткод: | D046 2582 |
| Деталь: | Bracket:Positioning:Right |
| Парткод: | D046 2583 |
| Деталь: | Drum Stay:Spring |
| Парткод: | B010 3211 |
| Деталь: | Spring:Joint |
| Парткод: | B010 3212 |
| Деталь: | Joint:Toner Hopper:Unit |
| Парткод: | B010 3206 |
| Деталь: | Electrode Plate:Development |
| Парткод: | B125 3213 |
| Деталь: | Bushing DIA8 |
| Парткод: | AA08 0340 |
| Деталь: | SPACER |
| Парткод: | AA13 2097 |
| Деталь: | Gear - 28Z |
| Парткод: | B010 3121 |
| Деталь: | Shaft:Development |
| Парткод: | D093 3319 |
| Деталь: | Pin - Stopper Click |
| Парткод: | BA14 6013 |
| Деталь: | Rubber Seal - Paddle Roller |
| Парткод: | 52 193 326 |
| Деталь: | Spacer - 0.3 |
| Парткод: | B125 3230 |
| Деталь: | Seal:Toner Supply |
| Парткод: | B286 3223 |
| Деталь: | Decal:Warning (High Temperature): Fusing/Paper Exit Unit |
| Парткод: | D093 4485 |
| Деталь: | Fusing/Paper Exit Unit:Assy |
| Парткод: | D093 4427 |
| Деталь: | Positioning Plate:Lock |
| Парткод: | B188 4159 |
| Деталь: | Right Lock Spring |
| Парткод: | AA06 6256 |
| Деталь: | Left Lock Spring |
| Парткод: | AA06 6257 |
| Деталь: | Decal:Warning (High Temperature) |
| Парткод: | D093 4426 |
| Деталь: | UPPER GUIDE |
| Парткод: | B010 4312 |
| Деталь: | Upper Drive Exit Roller |
| Парткод: | B125 4481 |
| Деталь: | Exit Roller Shaft |
| Парткод: | AA14 0844 |
| Деталь: | Exit Tube |
| Парткод: | A163 4236 |
| Деталь: | Tube holder |
| Парткод: | A163 4235 |
| Деталь: | Guide:Fusing/Paper Exit:Middle |
| Парткод: | B125 4477 |
| Деталь: | Lower Drive Exit Roller |
| Парткод: | B125 4479 |
| Деталь: | Shield:Guide:Right Upper |
| Парткод: | B286 4498 |
| Деталь: | Shield:Guide:Left Upper |
| Парткод: | B286 4497 |
| Деталь: | Grip:Exit |
| Парткод: | B286 4499 |
| Деталь: | Guide:Fusing/Paper Exit Unit: Left And Right |
| Парткод: | B286 4475 |
| Деталь: | Stripper Spring |
| Парткод: | AA06 6052 |
| Деталь: | Stripper Pawls |
| Парткод: | AE04 4054 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Pulley - 24T |
| Парткод: | AB03 0474 |
| Деталь: | Arm Spring |
| Парткод: | AA06 6643 |
| Деталь: | Idler Gear - 30z |
| Парткод: | B010 4324 |
| Деталь: | Arm:Drive:Fusing/Exit Unit |
| Парткод: | B125 4488 |
| Деталь: | Gear/Pulley - 24Z/24T |
| Парткод: | AB01 7680 |
| Деталь: | Timing Belt - 230XL |
| Парткод: | AA04 3527 |
| Деталь: | Arm Stopper |
| Парткод: | B257 4231 |
| Деталь: | Spring:Middle |
| Парткод: | AA06 1016 |
| Деталь: | Sheet:Block Light:Exit |
| Парткод: | B286 4470 |
| Деталь: | Shaft:Exit Roller |
| Парткод: | D093 4490 |
| Деталь: | Harness:DC:Main:Left:A (D093) |
| Парткод: | D093 5731 |
| Деталь: | Harness:DC:Main:Left:B (D094) |
| Парткод: | D094 5702 |
| Деталь: | Harness:DC:Main:Right |
| Парткод: | D093 5701 |
| Деталь: | PCB:MCU:Assy |
| Парткод: | D093 5280 |
| Деталь: | PCB:SIPU:Assy |
| Парткод: | D093 5432 |
| Деталь: | Harness:DC:LVDS:SCN |
| Парткод: | D093 5704 |
| Деталь: | Fan:MM60:24V |
| Парткод: | AX64 0181 |
| Деталь: | PCB:MB:Assy |
| Парткод: | D093 5435 |
| Деталь: | Harness:DC:Power Source:Connecting |
| Парткод: | D093 5703 |
| Деталь: | Duct:C/T Box |
| Парткод: | D093 5312 |
| Деталь: | Harness:DC:LVDS:Main |
| Парткод: | D093 5724 |
| Деталь: | Pulley - 76T |
| Парткод: | AB03 0746 |
| Деталь: | Bushing - 8mm |
| Парткод: | 50 530 223 |
| Деталь: | Bracket:Set Sensor |
| Парткод: | D093 4652 |
| Деталь: | Harness:DC:Scanner Unit:Set Sensor: Connecting |
| Парткод: | D093 5765 |
| Деталь: | Ground Wire:Scanner Unit:2 |
| Парткод: | B286 5741 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Grounding Plate:Original:Frontlower |
| Парткод: | B125 4753 |
| Деталь: | Bracket:Original Sensor:NA |
| Парткод: | B286 4631 |
| Деталь: | Bracket:Original Sensor |
| Парткод: | B286 4630 |
| Деталь: | Photo Reflection Sensor:PS117ED1 |
| Парткод: | AW01 0109 |
| Деталь: | Bracket:Registration Sensor |
| Парткод: | B125 4613 |
| Деталь: | Transport Roller:Original Insert:Assy |
| Парткод: | D093 4663 |
| Деталь: | Square bushing |
| Парткод: | H004 3755 |
| Деталь: | Guard |
| Парткод: | H072 2207 |
| Деталь: | Bushing:Arm:Front |
| Парткод: | B125 4656 |
| Деталь: | Gasket:Scanner:Guide Plate:Front |
| Парткод: | B286 5768 |
| Деталь: | Spacer - 0.3 |
| Парткод: | B125 3230 |
| Деталь: | Spacer:21.2 |
| Парткод: | B889 1435 |
| Деталь: | Rubber Seal - Paddle Roller |
| Парткод: | 52 193 326 |
| Деталь: | Harness:DC:Scanner Unit:NA |
| Парткод: | B286 5732 |
| Деталь: | Harness:DC:Scanner Unit (EU/CHN) |
| Парткод: | B286 5723 |
| Деталь: | Lever:Micro Switch |
| Парткод: | D093 4653 |
| Деталь: | Guide Plate:Front Lower:NA |
| Парткод: | B286 4692 |
| Деталь: | Guide Plate:Front Lower:EU |
| Парткод: | B286 4682 |
| Деталь: | Front Cis Guide |
| Парткод: | B125 4689 |
| Деталь: | Screw:Lever:Release:Blade |
| Парткод: | B188 3575 |
| Деталь: | Tightener - M16 |
| Парткод: | G568 2839 |
| Деталь: | STEPPED SCREW |
| Парткод: | 54 472 769 |
| Деталь: | Belt tensioner spring |
| Парткод: | AA06 0943 |
| Деталь: | Tensioner:Belt |
| Парткод: | B125 4815 |
| Деталь: | Pulley - 76T |
| Парткод: | AB03 0745 |
| Деталь: | Bushing - 8mm |
| Парткод: | 50 530 223 |
| Деталь: | Timing Belt - B60S2M480 |
| Парткод: | AA04 3588 |
| Деталь: | Spring Plate:Exposure Glass:Left |
| Парткод: | B125 1728 |
| Деталь: | Spring Plate:Exposure Glass:Right |
| Парткод: | B125 1727 |
| Деталь: | Exposure Glass |
| Парткод: | AC01 0006 |
| Деталь: | Transport Roller:Original Exhaust:Assy |
| Парткод: | D093 4673 |
| Деталь: | Guide Plate:Original:Rear Lower |
| Парткод: | B286 4696 |
| Деталь: | Front Discharge Brush |
| Парткод: | AA12 0125 |
| Деталь: | Bracket:Original:Paper Feed Sensor |
| Парткод: | B286 4616 |
| Деталь: | Harness - DC Scanner Unit |
| Парткод: | B275 5686 |
| Деталь: | Photo Reflection Sensor:PS117ED1 |
| Парткод: | AW01 0109 |
| Деталь: | Guide:CIS:Front:Small |
| Парткод: | B286 4691 |
| Деталь: | Contact Image Sensor:Service:Assy |
| Парткод: | D093 1640 |
| Деталь: | Bushing:Arm:Rear |
| Парткод: | B125 4697 |
| Деталь: | Cushion:Swivel:Stopper |
| Парткод: | B125 3659 |
| Деталь: | Vibrating Plate:Collection Bottle |
| Парткод: | B125 3671 |
| Деталь: | Cam:Gear:Swivel |
| Парткод: | B125 3674 |
| Деталь: | DC Motor 24V 5.85W |
| Парткод: | B286 3664 |
| Деталь: | Bracket:Swivel:Collection Bottle |
| Парткод: | B125 3672 |
| Деталь: | Swing Unit Idler Shaft |
| Парткод: | AA14 5830 |
| Деталь: | Leaf Spring:T/S Corona |
| Парткод: | B125 3864 |
| Деталь: | Guide Plate:T/S Corona:Lower |
| Парткод: | B125 3870 |
| Деталь: | Grounding Plate:T/S Corona:Mid |
| Парткод: | B125 3871 |
| Деталь: | Cover:Transfer Corona:Lower |
| Парткод: | B125 3872 |
| Деталь: | Guard:Leaf Spring |
| Парткод: | B125 3873 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Heater:120V:13W |
| Парткод: | AX40 0188 |
| Деталь: | Heater:230V:13W |
| Парткод: | AX40 0189 |
| Деталь: | Guide Plate:Transport |
| Парткод: | B286 3865 |
| Деталь: | Decal:Warning (High Temperature): Lengthwise |
| Парткод: | D093 1266 |
| Деталь: | Cover:Safety Switch |
| Парткод: | B125 4356 |
| Деталь: | Shield:Joint:Upper |
| Парткод: | B286 3683 |
| Деталь: | Joint:Collection Bottle |
| Парткод: | B125 3681 |
| Деталь: | Lever:Micro Switch |
| Парткод: | B125 1085 |
| Деталь: | Bracket:Latch:Right |
| Парткод: | B286 1084 |
| Деталь: | Idle Gear |
| Парткод: | AB01 7347 |
| Деталь: | Screw:Spring Washer:M2.6x5 |
| Парткод: | A571 7700 |
| Деталь: | Spring Washer:WW-6012 |
| Парткод: | B125 3687 |
| Деталь: | Gasket:20mm |
| Парткод: | B286 1050 |
| Деталь: | SPACER |
| Парткод: | AA13 2013 |
| Деталь: | Gear:Timing Pulley:Z100/T31 |
| Парткод: | AB01 7741 |
| Деталь: | Gear - 32/100Z |
| Парткод: | AB01 7676 |
| Деталь: | Bracket:DC Motor:Assy |
| Парткод: | B286 1135 |
| Деталь: | Brushless Motor:DC24V 24W:Z9 |
| Парткод: | AX06 0296 |
| Деталь: | Shoulder Screw - Pressure Arm |
| Парткод: | AA14 3139 |
| Деталь: | Guard |
| Парткод: | H072 2207 |
| Деталь: | Plate:Shaft |
| Парткод: | B125 1971 |
| Деталь: | Flange:Pulley |
| Парткод: | B286 1139 |
| Деталь: | PCB:VDB:Assy |
| Парткод: | D093 5450 |
| Деталь: | PCB:SIF:UNI:Assy |
| Парткод: | D093 5870 |
| Деталь: | Power Pack:CGB |
| Парткод: | AZ32 0151 |
| Деталь: | Cover:Printed Circuit Board |
| Парткод: | B286 1160 |
| Деталь: | Harness:DC:LVDS:Main |
| Парткод: | D093 5724 |
| Деталь: | Harness:High Voltage:Grid |
| Парткод: | B286 5715 |
| Деталь: | Harness:High Voltage |
| Парткод: | B286 5714 |
| Деталь: | Harness:High Voltage:Charge Corona |
| Парткод: | B286 5716 |
| Деталь: | LED Head:Assy |
| Парткод: | D093 1851 |
| Деталь: | Harness:DC:Main:Left:A (D093) |
| Парткод: | D093 5731 |
| Деталь: | Harness:DC:Main:Left:B (D094) |
| Парткод: | D094 5702 |
| Деталь: | Harness:DC:Main:Right |
| Парткод: | D093 5701 |
| Деталь: | Harness:DC:LVDS:SCN |
| Парткод: | D093 5704 |
| Деталь: | Harness:DC:Scanner:Motor |
| Парткод: | D093 5711 |
| Деталь: | Stay:FCC |
| Парткод: | B286 5617 |
| Деталь: | Gasket:Stay:FFC |
| Парткод: | B286 5620 |
| Деталь: | Bracket:VDB |
| Парткод: | B286 5618 |
| Деталь: | Positioning Pin |
| Парткод: | AA14 3859 |
| Деталь: | Rivet:MM5 |
| Парткод: | B125 1474 |
| Деталь: | Side Fence:Left:Assy |
| Парткод: | D093 4720 |
| Деталь: | Side Fence:Right:Assy |
| Парткод: | D093 4723 |
| Деталь: | Original Table:NA:Printing |
| Парткод: | D093 4702 |
| Деталь: | Original Table:Printing |
| Парткод: | D093 4700 |
| Деталь: | Cover:Operation Panel |
| Парткод: | B286 1500 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Guard Burring |
| Парткод: | B275 1670 |
| Деталь: | Decal:H-temp Warning:Exterior: Multi-language |
| Парткод: | D093 1265 |
| Деталь: | Cover:Rear Lower |
| Парткод: | D093 1284 |
| Деталь: | Decal:Original:Operate:Multi-language:EXP |
| Парткод: | D093 4885 |
| Деталь: | Used Toner Sensor |
| Парткод: | AW40 0014 |
| Деталь: | ROLLER HOLDER |
| Парткод: | A060 3827 |
| Деталь: | Toner Collection Bottle Roller |
| Парткод: | A060 3826 |
| Деталь: | Leaf Spring:Collection Bottle |
| Парткод: | B125 3688 |
| Деталь: | Collection Bottle |
| Парткод: | B286 3661 |
| Деталь: | Decal:Toner Recycling |
| Парткод: | B286 3662 |
| Деталь: | Harness:DC:Operation |
| Парткод: | B286 5763 |
Коды ошибок
101
143
144
161-1
161-2
161-3
161-4
186
300
305
392
400
401
402
406
440
460
508
520
521
522
530
541
542
543
544
545
546
547
551
553
557
559
561
563
632
633
634
635
636-1
636-2
650-1
650-4
650-5
651
652
653
670
671
672
687
690
816
819
820
821
833
842
851
853
854
855
856
857
858
859
860
861
863
864
865
866
867
868
870
872
873
874
875
876
877
878
880
900
901
920
921
925
SC641
SC954
SC965
SC967
SC984
SC990
SC991
SC992
SC994
SC997
SC998
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 143 |
| Display: | Service Call 143:Error |
| Description: | Motor |
| Causes: | • SBU defective • IPU defective • BCU defective • Harness between the SBU and IPU defective • Harness between the BCU-IPU defective • Standard white plate not installed correctly, or is dirty • Scanner mirrors and/or lenses are dirty or installed incorrectly |
| Remedy: | DC pick motor, no encoder feedback - staging motor - replace the “Staging motor” on page 4-79. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 161-1 |
| Description: | SIPU Error 1: FPGA Configuration Error. At power on, or when the machine returned from energy save mode, the FPGA Flash Program did not configure correctly. -or- An SIPU error occurred during the FPGA check after three attempts. |
| Causes: | • SIPU defective |
| Error code: | 161-2 |
| Display: | NCU CONSUMPTION |
| Description: | SIPU Error 2: Ri2005 Chip Failure At power on, or when the machine returned from energy save mode, an SIPU error occurred during Ri2500 access (Ri2500 did not respond within 5 ms). |
| Causes: | • SIPU defective |
| Error code: | 161-3 |
| Description: | SIPU Error 3: Ri2001A Chip Failure At power on, or when the machine returned from energy save mode, the Ri2001A chip on the SIPU failed (Ri2001A did not respond within 5 ms). |
| Causes: | • SIPU defective |
| Error code: | 161-4 |
| Description: | SIPU Error 4: Cetus Configuration Error At power on, or when the machine returned from energy save mode, Cetus configuration failed after three attempts within 810 ms |
| Causes: | • SIPU defective |
| Error code: | 186 |
| Display: | ERROR 186 HDC UNDERFLOW |
| Description: | Exposure Lamp 2 Lamp Regulator (Left) Error (D016/D097 only) The MCU detected a defect in the lamp regulator (left) when the 2nd exposure lamp lit. . |
| Causes: | • 2nd exposure lamp defective • 2nd lamp FFC (flat film cable) loose or defective • MCU to lamp regulator (left) harness defective • Lamp regulator (left) is defective • MCU defective • SIB defective |
| Error code: | 300 |
| Description: | High voltage power output error |
| Causes: | The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit). |
| Remedy: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB. |
| Error code: | 305 |
| Display: | ERROR 305 USB TIME OUT |
| Description: | Charge Corona Wire Cleaner Error The charge wire cleaner did not: (1) come from the home position within 5 s, or (2) did return to the home position within 3.75 s due to wire cleaner overload. |
| Causes: | • Cleaner unit blocked or damaged • Until replacement parts become available, set SP2804 to "0" to disable the charge-corona cleaning function so the machine can operate. |
| Error code: | 392 |
| Description: | Development Bias Error The development bias feedback voltage was less than 0.3 V for longer than 200 ms while the PWM duty value was more than 5% (indicating a development bias leak). |
| Causes: | • Bias terminal damaged • High voltage cable damaged, defective • CGB power pack defective |
| Error code: | 400 |
| Display: | Open top cover 400: Paper size error |
| Description: | TM sensor error |
| Causes: | The CPU detected a low voltage of the positive reflection output under the threshold in the TM sensor. |
| Remedy: | • TM sensors are dirty. • A solid print out due to an electrostatic charging error • The TM sensor is defective. 1. Clean the TM sensors. 2. Replace the TM sensors. 3. Check the image transfer unit. 4. Turn the power Off and On. |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 406 |
| Display: | SYSTEM HALT (*) 406 : WIPER ORG |
| Description: | ID Sensor Pattern Edge Detection Error The ID sensor pattern check could not detect the correct voltage on the ID sensor pattern (below 2.5V) within 0.6 sec. |
| Causes: | • ID sensor dirty • ID sensor harness loose, damaged, defective • ID sensor connector defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 440 |
| Description: | Transfer Output Error. A high voltage feedback voltage of less than 0.5 V was detected for 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 460 |
| Description: | DC Separation Corona Output Error A dc separation feedback voltage of less than 0.5 V was detected after more than 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 508 |
| Description: | Replace black developer |
| Causes: | • HP sensors on the left and right side loose, disconnected, defective • Cutter motor harness damaged, defective • HP sensors defective • Cutter motor defective Note: Paper can be fed from the bypass table if the roll feeder or paper cassette is not operationg. |
| Error code: | 520 |
| Description: | Replace optics filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 521 |
| Description: | Replace particle filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 522 |
| Description: | Replace upper fuser roller |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 530 |
| Description: | LSU Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the LSU fan motor. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 561 |
| Description: | Pressure roller end thermistor error 1 During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the end thermistor on the pressure roller returned a digital reading of more than 3.3V. |
| Causes: | • Pressure roller end thermistor not positioned properly • Pressure roller end thermistor connector loose, broken, defective • Pressure roller end thermistor defective • MCU defective |
| Error code: | 563 |
| Description: | Pressure roller end thermistor error 2 During the hot roller temperature control sequence, the end thermistor on the pressure roller returned a digital reading of less than 0.2V. |
| Causes: | • Pressure roller end thermistor connector loose • Pressure roller end thermistor short circuit, defective • MCU defective |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 633 |
| Description: | Key/card counter device error 2 During communication with the device, the MCU received a break (Low) signal. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 636-1 |
| Description: | SD Card Error CTL Expanded authentication module error |
| Causes: | • No expanded authentication module in the machine. (Install expanded authentication module.) • Expanded authentication module file is corrupted. • Expanded authentication module SD card is damaged. • No DESS module in the machine. (Install DESS module.) |
| Error code: | 636-2 |
| Description: | Version Error. The version of the expanded authentication module is not correct. |
| Causes: | • Install the correct file of the expanded authentication module. |
| Error code: | 650-1 |
| Description: | Authentication error Authentication for Cumin-M failed at a dial up connection. |
| Causes: | • Incorrect SP settings • Disconnected telephone line • Disconnected modem board |
| Remedy: | • Check and set the correct user name (SP5816-156) and password (SP5816-157). |
| Error code: | 650-4 |
| Description: | Incorrect modem setting • Dial-up failed due to incorrect modem setting. (Possible causes same as 650-1 above.) |
| Causes: | • Dial-up failed due to incorrect modem setting. (Possible causes same as 650-1 above.) |
| Remedy: | • Check, correct modem settings (SP5819-160) |
| Error code: | 650-5 |
| Description: | Communication line error The supplied voltage is not sufficient due to a defective communication line or defective connection. |
| Causes: | • Possible cause same as 650-1 above • Consult with the user`s local telephone company. |
| Error code: | 651 |
| Description: | @Remote communication error 2 An illegal dial-up to the service center was attempted by @Remote. |
| Causes: | • Software bug |
| Error code: | 652 |
| Description: | Remote service ID2 mismatching ID2 for @Remote certification is mismatching between the controller board and NVRAM. Used controller board installed. Used NVRAM installed An unexpected error occurs when the modem (Embedded RCG-M) tries to call the center with a dial up connection. |
| Causes: | If this occurs during the @Remote installation • Check the NVRAM`s validity and serial number, write the common certificate, and then retry the installation. If this occurs after the @Remote installation • Clear the current @Remote setting, check the NVRAM`s validity and serial number, write the common certificate, and then retry the installation. |
| Error code: | 653 |
| Description: | Incorrect remote service ID2 If one of the following applies to the ID2 recorded in the NVRAM: • The character string is not 17 characters long. • Unprintable characters are included. • It contains spaces only. • It is blank. |
| Remedy: | • Replace the NVRAM • Clear the current @Remote setting, write the common certificate, and then retry the installation. |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 671 |
| Description: | Engine board mismatch error Engine board and controller mismatch detected. |
| Causes: | • Wrong engine board installed. • Wrong controller board installed. • Check the type of engine board and controller board. |
| Remedy: | 1. Replace the BCU. 2. Replace the controller board. |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 690 |
| Description: | GAVD Communication Error |
| Causes: | The ID of the GAVD is not identified during initialization. The chip ID of the GAVD cannot be detected by the machine at power-on. |
| Remedy: | • Defective EGB 1. Replace the EGB. EE |
| Error code: | 816 |
| Display: | SYSTEM HALT (*) 816 : FW/FROM WRC |
| Description: | Energy saving I/O sub-system error |
| Causes: | The energy saving I/O sub-system detects an error. • Defective energy saving I/O sub-system • The energy saving I/O sub-system detects a controller board error (No response) |
| Remedy: | • Turn the main power switch off and on. • Replace the controller board. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 833 |
| Display: | SYSTEM HALT (*) 833 : FW/PRN MDL |
| Description: | Self-diagnostic error 8: Engine I/F ASIC |
| Causes: | [0F30] [0F31] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. [0F41] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. |
| Error code: | 842 |
| Description: | Service Scanner |
| Causes: | This error indicates that a scanner communications failure. |
| Remedy: | 1 Scanner control card to flatbed inteconnect card cable Check for correct installation of the scan control to flatbed interconnect card cable. 2 Motor drive card to flatbed interconnect card cable Check for correct installation of the motor driver card to flatbed interconnect card cable. 3 Motor driver card Flatbed interconnect card If the cables are good and are properly connected, replace the following FRUs in the order shown: • Flatbed interconnect card assembly • Motor driver card assembly |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 858 |
| Description: | Data encryption conversion error (1) |
| Causes: | -01 A serious error has occurred during the data conversion performed for updating the key for data encryption. • The data in the USB flash drive is damaged. • A communication error has occurred due to electromagnetic waves or other noise. • Replace the controller board. * However, if it is "-30", the machine may recover by turning the main power switch off and then back on. -02 A Data encryption conversion error (2) A serious error occurs when data is encrypted to update an encryption key. Defective NVRAM Replace the controller board. -30 A Data encryption conversion error (3) A recoverable error has occurred before starting data conversion. Defective NVRAM • Turn the main switch off and on. • If the error reoccurs, replace the controller board. -31 A A serious error occurs while the data is encrypted. Same as SC991 Same as SC991 |
| Error code: | 859 |
| Description: | HDD data encryption error |
| Causes: | -01 B HDD check error • Hard disk data conversion has been selected, but the hard disk is not installed. • The hard disk is not mounted properly. • No HDD installed • Hard disk formatting is not completed. • The encryption key on the board and the actual encryption key in the hard disk do not match. • Install the HDD correctly. • Initialize the HDD with SP5-832-001. -02 B Power failure during data encryption. The data conversion in the NVRAM or hard disk has not completed successfully. Power interruption has occurred during the conversion of the data in the NVRAM or hard disk Initialize the HDD with SP5-832-001. -10 B Data Read/Write command error Due to time-out, serial communication error, or other problems in DMAC, an irregular DMAC return value has occurred consecutively two or more times Noise or other problems in the SATA connection Same as SC863 |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 877 |
| Description: | HDD Data Erase Error The Data Overwrite Security option cannot scramble and erase data on the HDD because the DOS SD card has been corrupted or has |
| Causes: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not been removed from the SD card slot. |
| Remedy: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not solve the problem, the SD card has been damaged.) • Install a new NVRAM • Install a new Data Overwrite Security option with a new SD card |
| Error code: | 878 |
| Description: | TPM electronic recognition error |
| Causes: | -00 The system firmware is not authenticated by TPM. The system hash value registered in the TPM at the machine`s system startup does not match that registered in the USB flash drive. • The system module was updated without going through the formal update process. • Incorrect operating of the USB flash. Replace the board. -01 D USB Flash error An error has occurred in the file system in the USB flash drive. The file system of the USB flash drive is damaged. Replace the controller board. -02 D TPM error An error has occurred in the TPM or TPM driver. Defective TPM Replace the controller board. -03 D TCSD error An error has occurred in the TPM software stack. • The TPM software stack cannot be launched. • The file required for the TPM software stack is missing. Replace the controller board. |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | SC641 |
| Description: | Engine-Controller Communication Error: No Response |
| Causes: | There was no response to a frame sent from The Controller Board To the engine. |
| Remedy: | • Cycle the machine off/on. |
| Error code: | SC954 |
| Description: | Printer Image Setting Error The IPU did not issue the signal required to start image processing for the printing mode within 60 s after the paper stops for registration. |
| Causes: | • Software defective • Replace the software (all firmware modules). • IPU defective |
| Error code: | SC965 |
| Description: | Print start signal error 1 The printer received another print start signal after print job has already started. |
| Causes: | • Main machine firmware defective • Replace all firmware modules on the main machine |
| Error code: | SC967 |
| Description: | Print start signal error 2 The printer received another print start signal after print job has already started. |
| Causes: | • Main machine firmware defective • Replace all firmware modules on the main machine • IOB defective |
| Error code: | SC984 |
| Description: | Print image data send error No data was sent within 1 sec. after the print image data stream started. |
| Causes: | • Harness from IPU to controller board loose, broken, defective • IPU defective |
| Error code: | SC990 |
| Description: | Software error 2 The software performs an unexpected function and the program cannot continue. |
| Causes: | An unexpected operation was encountered by the software. |
| Remedy: | • Software defective, re-boot 1) Execute SP7403 or print an SMC Report (SP5990) to read the history of the 10 most recent logged errors. 2) If you press the zero key on the operation panel with the SP selection menu displayed, you will see detailed information about the recently logged SC990 or SC991, including the software file name, line number, and so on. 1) is the recommended method, because another SC could write over the information for the previous SC. |
| Error code: | SC991 |
| Description: | Software error 3 The software performs an unexpected function and the program cannot continue. However, unlike SC990, recovery processing allows the program to continue. |
| Causes: | The software peformed an unexpected function and the program cannot continue. Recovery processing allows the program to continue. |
| Remedy: | • Software defective, re-boot 1) Execute SP7403 or print an SMC Report (SP5990) to read the history of the 10 most recent logged errors. 2) If you press the zero key on the operation panel with the SP selection menu displayed, you will see detailed information about the recently logged SC990 or SC991, including the software file name, line number, and so on. 1) is the recommended method, because another SC could write over the information for the previous SC. |
| Error code: | SC992 |
| Description: | Software error 4: Undefined An error not controlled by the system occurred (the error does not come under any other SC code). |
| Causes: | An error not controlled by the system occurred (the error does not come under any other SC code). |
| Remedy: | • Software defective • Turn the machine power OFF and ON. The machine cannot be used until this error is cleared. |
| Error code: | SC994 |
| Description: | Operation Panel Management Records Exceeded |
| Causes: | An error occurred because the number of records exceeded the limit for images managed in the service layer of the firmware. This can occur if there if there are too many application screens open on the operation panel. |
| Remedy: | • No action required because this SC does not interfere with operation of the machine. |
| Error code: | SC997 |
| Description: | Cannot select application function An application does not start after the user pushed the correct key on the operation panel. |
| Causes: | An application did not start after pressing the appropriate key on the operation panel. |
| Remedy: | • Software bug • A RAM or DIMM option necessary for the application is not installed or not installed correctly. |
| Error code: | SC998 |
| Description: | Application cannot start Register processing does not operate for an application within 60 s after the machine power is turned ON. No applications not start correctly, and all end abnormally. |
| Causes: | Register processing did not execute for an application within 60 sec. after the machine was switched on. No applications start correctly, and all end abnormally. |
| Remedy: | • Software bug • A RAM or DIMM option necessary for the application is not installed or not installed correctly. |
