Ricoh SP4210N
Рейтинг
Модули
PAPER TRAY
FUSING UNIT 1
Paper exit
ELECTRICAL SECTION 1
DRIVE SECTION
LD unit
EXTERIOR 1
TRANSFER SECTION
EXTERIOR 2
PAPER REGISTRATION 2
FUSING UNIT 2
ELECTRICAL SECTION 2
PAPER REGISTRATION 1
Детали EXTERIOR 2
| Деталь: | PAPER TRAY UNIT |
| Парткод: | G175 3050 |
| Деталь: | Tape - Sheet: Tray |
| Парткод: | G096 3094 |
| Деталь: | Tray Sheet 1 |
| Парткод: | G360 3091 |
| Деталь: | Tray Sheet 2 |
| Парткод: | G360 3092 |
| Деталь: | Tray Sheet 3 |
| Парткод: | G360 3093 |
| Деталь: | PAPER TRAY COVER |
| Парткод: | G096 3052 |
| Деталь: | Paper Size Sensor Board |
| Парткод: | G096 3075 |
| Деталь: | Paper Tray Arm |
| Парткод: | G096 3071 |
| Деталь: | SPRING TENSION |
| Парткод: | G096 3083 |
| Деталь: | Paper Set Direction Label |
| Парткод: | G096 3144 |
| Деталь: | LEFT SIDE FENCE |
| Парткод: | G096 3055 |
| Деталь: | Gear - 16Z |
| Парткод: | A267 2869 |
| Деталь: | RIGHT SIDE FENCE |
| Парткод: | G096 3056 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | G175 2818 |
| Деталь: | BASE PAD |
| Парткод: | G555 3069 |
| Деталь: | Separation Compression Spring |
| Парткод: | G096 3084 |
| Деталь: | Friction Pad Adhesion |
| Парткод: | G096 3066 |
| Деталь: | Cassette Protection |
| Парткод: | G029 2609 |
| Деталь: | End Fence Pressure |
| Парткод: | G096 3088 |
| Деталь: | End Fence Protection |
| Парткод: | G096 3087 |
| Деталь: | End Fence Tension Spring 12N |
| Парткод: | G096 3090 |
| Деталь: | End Fence Compression Spring 3.5N |
| Парткод: | G096 3089 |
| Деталь: | End Fence Lever |
| Парткод: | G096 3086 |
| Деталь: | END FENCE |
| Парткод: | G096 3085 |
| Деталь: | Paper Tray Cap |
| Парткод: | G096 3063 |
| Деталь: | Protection Label |
| Парткод: | G096 3078 |
| Деталь: | Rear Paper Tray |
| Парткод: | G096 3060 |
| Деталь: | Paper Tray Supporting Plate |
| Парткод: | G096 3065 |
| Деталь: | Paper Volume Sensor Board |
| Парткод: | G096 3070 |
| Деталь: | PAPER TRAY |
| Парткод: | G096 3051 |
| Деталь: | Tray Sheet |
| Парткод: | G175 3058 |
| Деталь: | Fusing Unit: NA: Assy |
| Парткод: | G175 4118 |
| Деталь: | Fusing Unit: EU: Assy |
| Парткод: | G175 4127 |
| Деталь: | Entrance Guide Plate - Upper |
| Парткод: | G175 4644 |
| Деталь: | Heater - 765W 120V |
| Парткод: | G175 0180 |
| Деталь: | Heater - 765W 230V |
| Парткод: | G175 0179 |
| Деталь: | External Circlip |
| Парткод: | G052 4700 |
| Деталь: | Gear - 41Z |
| Парткод: | G175 4619 |
| Деталь: | Bearing 30x42x7 |
| Парткод: | G052 4618 |
| Деталь: | Hot Roller |
| Парткод: | G175 4063 |
| Деталь: | Fusing drawer - NA |
| Парткод: | G175 5500 |
| Деталь: | Fusing drawer - 230V |
| Парткод: | G175 5510 |
| Деталь: | Harness - Fusing Unit Set 120V |
| Парткод: | G175 5520 |
| Деталь: | Harness - Fusing Set 230V |
| Парткод: | G175 5521 |
| Деталь: | Fusing Thermistor |
| Парткод: | G096 5501 |
| Деталь: | Holder Plate - Fusing Harness |
| Парткод: | G175 4625 |
| Деталь: | Thermostat Assy |
| Парткод: | G096 4611 |
| Деталь: | Electrode Plate - Right |
| Парткод: | G175 4602 |
| Деталь: | Upper Harness Plate |
| Парткод: | G096 4695 |
| Деталь: | Left Fusing Lamp bracket |
| Парткод: | G096 4615 |
| Деталь: | Electrode: Heater |
| Парткод: | G088 4618 |
| Деталь: | Exit Roller Supporting Plate |
| Парткод: | G096 4638 |
| Деталь: | Decal Warning (High Temperature) |
| Парткод: | AA00 0301 |
| Деталь: | Spring - Fusing Stripper |
| Парткод: | G052 4622 |
| Деталь: | Hot Roller Stripper |
| Парткод: | G052 4624 |
| Деталь: | Right Heater Bracket |
| Парткод: | G096 4616 |
| Деталь: | Fusing Right Cover |
| Парткод: | G096 4692 |
| Деталь: | Discharge Brush - Bearing |
| Парткод: | G175 4642 |
| Деталь: | Ground Plate - Fusing |
| Парткод: | G175 4690 |
| Деталь: | Spring Plate - Fusing Exit |
| Парткод: | G052 4647 |
| Деталь: | Upper Fusing Exit Guide Plate |
| Парткод: | G096 4635 |
| Деталь: | Exit Roller Holder |
| Парткод: | G052 4639 |
| Деталь: | EXIT ROLLER |
| Парткод: | G800 4854 |
| Деталь: | Frame: Fusing: Upper: Assy [TSB001] |
| Парткод: | G175 4629 |
| Деталь: | Harness: Exit: Sensor |
| Парткод: | M001 5403 |
| Деталь: | Exit Feeler Holder |
| Парткод: | G052 1044 |
| Деталь: | Photointerruptor: LG248NL1 |
| Парткод: | GW02 0020 |
| Деталь: | Fusing Exit Feeler |
| Парткод: | G052 1042 |
| Деталь: | Spring - Fusing Exit Feeler |
| Парткод: | G052 1046 |
| Деталь: | Rear Cover Sw Bracket |
| Парткод: | G052 1272 |
| Деталь: | Spring - Micro Switch |
| Парткод: | G052 1273 |
| Деталь: | Micro Switch Lever |
| Парткод: | G052 1274 |
| Деталь: | Pulley - Paper Exit |
| Парткод: | G052 4855 |
| Деталь: | Bushing - Paper Exit |
| Парткод: | G052 1049 |
| Деталь: | EXIT ROLLER |
| Парткод: | G096 4850 |
| Деталь: | BUSHING |
| Парткод: | G800 4851 |
| Деталь: | Exit Roller Ground Plate |
| Парткод: | G096 1262 |
| Деталь: | Exit Bracket |
| Парткод: | G096 1041 |
| Деталь: | Exit Brush Discharge |
| Парткод: | G096 4888 |
| Деталь: | Exhaust Sensor Feeler |
| Парткод: | G096 1043 |
| Деталь: | Discharge Lamp: Cassis |
| Парткод: | G129 3522 |
| Деталь: | Heat Insulating Plate - Front |
| Парткод: | G175 1032 |
| Деталь: | Rubber Foot - FF-006(P4070)N |
| Парткод: | GH01 0007 |
| Деталь: | Right Paper Tray Rail |
| Парткод: | G096 1081 |
| Деталь: | Left Paper Tray Rail |
| Парткод: | G096 1082 |
| Деталь: | Base Ground Plate |
| Парткод: | G096 1085 |
| Деталь: | Spring Plate - Duplex Rail |
| Парткод: | G052 1027 |
| Деталь: | Right Duplex Rail |
| Парткод: | G096 1021 |
| Деталь: | Left Duplex Rail |
| Парткод: | G096 1022 |
| Деталь: | Right Fusing Lock Lever |
| Парткод: | G052 4696 |
| Деталь: | Left Fusing Lock Lever |
| Парткод: | G052 4697 |
| Деталь: | Decal: Warning (High Temperature) |
| Парткод: | G128 1151 |
| Деталь: | Drawer Bracket - Fusing |
| Парткод: | G175 1056 |
| Деталь: | Harness: Fusing: NA |
| Парткод: | M001 5404 |
| Деталь: | Harness: Fusing: EU |
| Парткод: | M001 5409 |
| Деталь: | Harness- Power Source |
| Парткод: | M001 5400 |
| Деталь: | DC Power Supply: 136W: DOM/NA |
| Парткод: | GZ23 0039 |
| Деталь: | DC Power Supply: 136W: EU/AA |
| Парткод: | GZ23 0040 |
| Деталь: | Power Pack - BCT |
| Парткод: | GZ32 0014 |
| Деталь: | Bracket: PSU: Assy |
| Парткод: | M001 1101 |
| Деталь: | Lower Fusing Heat Insulating Plate |
| Парткод: | G096 1031 |
| Деталь: | Inlet Bracket |
| Парткод: | G096 1271 |
| Деталь: | Power Supply Cord: EU |
| Парткод: | G102 5502 |
| Деталь: | Harness - Power Pack |
| Парткод: | G111 5419 |
| Деталь: | Paper Tray Spring Plate Assy |
| Парткод: | G096 1087 |
| Деталь: | Ground Plate - Registration |
| Парткод: | G096 3338 |
| Деталь: | Drum Terminal |
| Парткод: | G052 1252 |
| Деталь: | Harness: Main Switch: DOM/NA |
| Парткод: | M001 5412 |
| Деталь: | Harness: Main Switch: EU |
| Парткод: | M001 5413 |
| Деталь: | Fan Motor MM92: 24V |
| Парткод: | G129 1051 |
| Деталь: | Inlet: JPN: Assy |
| Парткод: | G110 5501 |
| Деталь: | Inlet - EU |
| Парткод: | G096 5506 |
| Деталь: | Choke Coil |
| Парткод: | G129 5205 |
| Деталь: | Hexagonal Bolt: Double: Screw: Round Point: M3x7 |
| Парткод: | G102 1193 |
| Деталь: | Fan: MM40x15: Nidec: L |
| Парткод: | GX64 0029 |
| Деталь: | Brushless Motor: DC24V: 31W |
| Парткод: | M001 1050 |
| Деталь: | Drive Unit Bracket |
| Парткод: | M001 1122 |
| Деталь: | Magnetic clutch |
| Парткод: | G175 3209 |
| Деталь: | Spring Clutch Bracket |
| Парткод: | G175 2554 |
| Деталь: | Magnetic Clutch: 1turn: Z41 |
| Парткод: | G129 2551 |
| Деталь: | Gear - Fusing 1 |
| Парткод: | G052 1104 |
| Деталь: | Gear - Paper Feed 1 |
| Парткод: | G052 1108 |
| Деталь: | Gear - Paper Feed 2 |
| Парткод: | G052 1109 |
| Деталь: | Gear - Paper Feed 6 |
| Парткод: | G052 1113 |
| Деталь: | Gear - Paper Feed 5 |
| Парткод: | G052 1112 |
| Деталь: | Gear - Paper Feed 4 |
| Парткод: | G052 1111 |
| Деталь: | Gear - Paper Feed 3 |
| Парткод: | G052 1110 |
| Деталь: | Gear - 45Z |
| Парткод: | G175 1106 |
| Деталь: | Gear - Pulley - Fusing |
| Парткод: | G052 1107 |
| Деталь: | WAVE WASHER |
| Парткод: | 5353 1803 |
| Деталь: | Spring - Paper Exit Release |
| Парткод: | G052 1120 |
| Деталь: | Drive Belt |
| Парткод: | G052 1121 |
| Деталь: | Spacer - Drive Unit |
| Парткод: | G052 1123 |
| Деталь: | Gear: PCU |
| Парткод: | G088 1103 |
| Деталь: | Gear - Fusing 2 |
| Парткод: | G052 1105 |
| Деталь: | Harness Holder |
| Парткод: | G175 2555 |
| Деталь: | Rivet: Toner Supply: DIA5 |
| Парткод: | G102 3324 |
| Деталь: | Supporter: Harness: Main |
| Парткод: | M001 1080 |
| Деталь: | Imaging Unit |
| Парткод: | M001 1904 |
| Деталь: | Synchronization Detector |
| Парткод: | G052 5060 |
| Деталь: | MIRROR CLAMP |
| Парткод: | G052 2774 |
| Деталь: | Mirror - 1 |
| Парткод: | GC03 0026 |
| Деталь: | Mirror - 2 |
| Парткод: | GC03 0027 |
| Деталь: | DTL |
| Парткод: | GC02 5010 |
| Деталь: | Right DTL Holder |
| Парткод: | G052 2771 |
| Деталь: | Left DTL Holder |
| Парткод: | G052 2772 |
| Деталь: | Shutter - LD |
| Парткод: | G052 2780 |
| Деталь: | Mirror - Sync Detector |
| Парткод: | GC03 0028 |
| Деталь: | Spring - LD Unit |
| Парткод: | G052 2764 |
| Деталь: | Laser Diode Unit |
| Парткод: | M001 1916 |
| Деталь: | LD Holder |
| Парткод: | G052 2763 |
| Деталь: | Cylindrical Lens |
| Парткод: | GC02 5011 |
| Деталь: | Cylindrical Lens Holder |
| Парткод: | G052 2773 |
| Деталь: | Harness - Polygon Mirror Motor |
| Парткод: | G168 5403 |
| Деталь: | Shield: Harness |
| Парткод: | G088 2775 |
| Деталь: | Spring Holder - Shield Glass |
| Парткод: | G052 2777 |
| Деталь: | Shield Glass - Polygon Motor |
| Парткод: | GC01 5005 |
| Деталь: | Polygon Scanner Motor: DC24V 24W |
| Парткод: | GX06 0029 |
| Деталь: | Cover: Optical Housing: Assy |
| Парткод: | G088 2785 |
| Деталь: | Caution Decal - Laser |
| Парткод: | G111 1910 |
| Деталь: | Shield: Cover: Polygon Scanner |
| Парткод: | G088 2789 |
| Деталь: | Shield Glass |
| Парткод: | G129 1902 |
| Деталь: | Cylindrical Lens |
| Парткод: | G029 1975 |
| Деталь: | Holder: Sync Detector |
| Парткод: | G168 1922 |
| Деталь: | Harness: LDB |
| Парткод: | M001 5410 |
| Деталь: | Upper Seal - Rear Cover |
| Парткод: | G175 1258 |
| Деталь: | LEFT COVER |
| Парткод: | G175 1253 |
| Деталь: | OPERATION PANEL |
| Парткод: | M001 1402 |
| Деталь: | Harness: Exit: Sensor |
| Парткод: | M001 5403 |
| Деталь: | UPPER COVER |
| Парткод: | M001 1652 |
| Деталь: | Paper Exit Sub-unit Assy |
| Парткод: | G096 1509 |
| Деталь: | Exit cover |
| Парткод: | G096 1512 |
| Деталь: | Inner Exit Cover Roller |
| Парткод: | G052 4875 |
| Деталь: | Left Holder - Exit Driven Roller |
| Парткод: | G052 4871 |
| Деталь: | Outer Exit Cover Roller |
| Парткод: | G052 4873 |
| Деталь: | Left Spring Plate |
| Парткод: | G052 4876 |
| Деталь: | Right Spring Plate |
| Парткод: | G052 4877 |
| Деталь: | Right Holder - Exit Driven Roller |
| Парткод: | G052 4872 |
| Деталь: | REAR COVER |
| Парткод: | G175 1229 |
| Деталь: | LOUVER |
| Парткод: | G175 1651 |
| Деталь: | RIGHT COVER |
| Парткод: | G175 1650 |
| Деталь: | Warning Cover (Electrical) |
| Парткод: | G096 1257 |
| Деталь: | CASSETTE COVER |
| Парткод: | G096 3111 |
| Деталь: | Slide Guide |
| Парткод: | G175 1406 |
| Деталь: | Lower Seal - Rear Cover |
| Парткод: | G175 1255 |
| Деталь: | Left Seal - Rear Cover |
| Парткод: | G175 1256 |
| Деталь: | Right Seal - Rear Cover |
| Парткод: | G175 1257 |
| Деталь: | Transport Guide Pin |
| Парткод: | G096 1019 |
| Деталь: | Spring - Transfer |
| Парткод: | G052 3627 |
| Деталь: | Left Bushing - Transfer |
| Парткод: | G052 3626 |
| Деталь: | Right Bushing - Transfer |
| Парткод: | G052 3625 |
| Деталь: | Separation Electrode Plate |
| Парткод: | G096 3621 |
| Деталь: | Electrode Plate Cover |
| Парткод: | G096 3622 |
| Деталь: | Registration Guide |
| Парткод: | G096 3345 |
| Деталь: | Registration Guide Long |
| Парткод: | G096 3346 |
| Деталь: | Transfer Terminal |
| Парткод: | G052 3623 |
| Деталь: | Separation Terminal |
| Парткод: | G052 3624 |
| Деталь: | Transport Guide |
| Парткод: | G096 1018 |
| Деталь: | TRANSFER ROLLER ASSY |
| Парткод: | G129 6260 |
| Деталь: | Gear - Transfer Roller |
| Парткод: | G129 6252 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | G129 6257 |
| Деталь: | Positioning Roller - Transfer |
| Парткод: | G129 6251 |
| Деталь: | TRANSFER GUIDE PLATE ASSY |
| Парткод: | G096 3640 |
| Деталь: | Transfer Guide Plate Sheet |
| Парткод: | G096 3641 |
| Деталь: | Transport Guide Ground Plate |
| Парткод: | G096 3628 |
| Деталь: | Transport Terminal Guide |
| Парткод: | G096 3629 |
| Деталь: | Charge Terminal - High Voltage |
| Парткод: | G052 1255 |
| Деталь: | Inner Terminal - Charge |
| Парткод: | G052 1254 |
| Деталь: | Development Terminal - High Voltage |
| Парткод: | G052 1256 |
| Деталь: | Development Terminal |
| Парткод: | G052 1253 |
| Деталь: | CHARGE TERMINAL |
| Парткод: | G052 1251 |
| Деталь: | BUSHING |
| Парткод: | G129 6255 |
| Деталь: | Rivet: DIA3.5 |
| Парткод: | M001 1082 |
| Деталь: | Supporter: Harness: Main: 2 |
| Парткод: | M001 1081 |
| Деталь: | Manual Feed Table: L: Assy |
| Парткод: | G175 3271 |
| Деталь: | Side Fence: Manual Feed: Left |
| Парткод: | G175 3277 |
| Деталь: | Side Fence: Manual Feed: Right |
| Парткод: | G175 3276 |
| Деталь: | Decal: Model Name Plate: P2: RIC: EXP |
| Парткод: | M001 1261 |
| Деталь: | Decal: Model Name: NAS |
| Парткод: | M001 1265 |
| Деталь: | Decal: Model Name: SAV |
| Парткод: | M001 1262 |
| Деталь: | Decal: Model Name: REX |
| Парткод: | M001 1266 |
| Деталь: | Decal: Model Name: GES: NA |
| Парткод: | M001 1263 |
| Деталь: | Decal: Model Name: GES: EU |
| Парткод: | M001 1268 |
| Деталь: | Decal: Model Name: LAN: NA |
| Парткод: | M001 1264 |
| Деталь: | Decal: Model Name: LAN: EU |
| Парткод: | M001 1267 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 5215 2713 |
| Деталь: | Receptacle - 99RH144 |
| Парткод: | G052 5362 |
| Деталь: | Spring Plate - Receptacle |
| Парткод: | G052 1544 |
| Деталь: | SIDE FENCE GEAR |
| Парткод: | G800 3133 |
| Деталь: | Extension Tray: Manual Feed: L |
| Парткод: | G175 3342 |
| Деталь: | Cover: Manual Feed Table |
| Парткод: | G175 3272 |
| Деталь: | Spring - Bypass |
| Парткод: | G052 3278 |
| Деталь: | Logo: Ricoh |
| Парткод: | G176 0410 |
| Деталь: | Logotype: GES |
| Парткод: | J007 1511 |
| Деталь: | Logotype: NSA |
| Парткод: | J007 1512 |
| Деталь: | Logotype: REX |
| Парткод: | J007 1513 |
| Деталь: | Plate: Logo: SVN |
| Парткод: | GA00 1051 |
| Деталь: | Plate: Logo: GES |
| Парткод: | GA00 1052 |
| Деталь: | Plate: Logo: LAN |
| Парткод: | GA00 1056 |
| Деталь: | Front door |
| Парткод: | G175 1260 |
| Деталь: | Latch - By Pass Feed Table |
| Парткод: | AG07 1007 |
| Деталь: | Thermistor- Transfer |
| Парткод: | G175 3539 |
| Деталь: | Sheet - Soundproof |
| Парткод: | G052 3356 |
| Деталь: | Misfeed Removal Decal |
| Парткод: | G096 1551 |
| Деталь: | Door lever |
| Парткод: | G175 1516 |
| Деталь: | Spring - Lock Lever |
| Парткод: | G052 1518 |
| Деталь: | Shutter Feeler |
| Парткод: | G096 1517 |
| Деталь: | HARNESS COVER |
| Парткод: | G175 1251 |
| Деталь: | Spring - Receptacle |
| Парткод: | G052 1541 |
| Деталь: | Collar - Receptacle |
| Парткод: | G052 1542 |
| Деталь: | Left Bushing - Registration |
| Парткод: | G052 3258 |
| Деталь: | Spring - Registration Roller |
| Парткод: | AA06 3539 |
| Деталь: | Magnetic Clutch - Registration |
| Парткод: | G175 2585 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2144 |
| Деталь: | Registration Drive Ground Plate |
| Парткод: | G096 3336 |
| Деталь: | Paper Tray Spring Plate Assy |
| Парткод: | G096 1087 |
| Деталь: | PHOTOSENSOR |
| Парткод: | G175 2551 |
| Деталь: | Registration Sensor Bracket |
| Парткод: | G175 3268 |
| Деталь: | Driven Registration Roller Mm14 |
| Парткод: | G096 3315 |
| Деталь: | Cleaner Film - Registration |
| Парткод: | G175 3267 |
| Деталь: | Right Bushing - Registration |
| Парткод: | G052 3257 |
| Деталь: | Harness: Sensor: Connecting |
| Парткод: | M001 5407 |
| Деталь: | Toner End Sensor |
| Парткод: | G052 3390 |
| Деталь: | Spring - Toner End Sensor |
| Парткод: | G052 3396 |
| Деталь: | Upper Guide Plate - Registration |
| Парткод: | G175 3266 |
| Деталь: | Decal - Registration |
| Парткод: | G052 3351 |
| Деталь: | Registration Roller - Drive |
| Парткод: | G175 3316 |
| Деталь: | Fusing Left Cover |
| Парткод: | G175 4698 |
| Деталь: | Pressure Spring - Fusing |
| Парткод: | G129 4102 |
| Деталь: | Pressure Roller Lever |
| Парткод: | G175 4662 |
| Деталь: | Bushing - Pressure Roller |
| Парткод: | G052 4665 |
| Деталь: | Gear - Fusing Idler |
| Парткод: | G052 4676 |
| Деталь: | Gear - Fusing Idler |
| Парткод: | G052 4677 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | G175 4681 |
| Деталь: | Pressure Frame |
| Парткод: | G175 4650 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | G175 0126 |
| Деталь: | Gear - 15Z |
| Парткод: | G175 4673 |
| Деталь: | BUSHING |
| Парткод: | G800 4851 |
| Деталь: | Fusing Exit Roller |
| Парткод: | G096 4674 |
| Деталь: | Discharge Brush - Pressure |
| Парткод: | G052 4692 |
| Деталь: | Ground Plate - Fusing Pressure |
| Парткод: | G052 4691 |
| Деталь: | Decal - High Temperature |
| Парткод: | G175 4693 |
| Деталь: | Right Pressure Lever |
| Парткод: | G175 4183 |
| Деталь: | Left Pressure Lever |
| Парткод: | G175 4182 |
| Деталь: | Pressure Lever Shaft |
| Парткод: | G175 4181 |
| Деталь: | Knob Screw: M3 |
| Парткод: | G104 5141 |
| Деталь: | Panel: Control Board: Assy |
| Парткод: | M001 1106 |
| Деталь: | Panel Knob Screw |
| Парткод: | B622 5825 |
| Деталь: | Left Guide 1 |
| Парткод: | G108 5107 |
| Деталь: | SD-Card Cover |
| Парткод: | G168 5115 |
| Деталь: | PCB: CTL: S-P2: EXP: Assy |
| Парткод: | M001 5365 |
| Деталь: | NVRAM - ZERO Counter |
| Парткод: | M001 9590 |
| Деталь: | Panel - Interface |
| Парткод: | B132 5836 |
| Деталь: | Bracket: EGB |
| Парткод: | M001 1105 |
| Деталь: | PCB: EGB: Assy |
| Парткод: | M001 5011 |
| Деталь: | Harness: Duplex: Option |
| Парткод: | M001 5401 |
| Деталь: | Right Guide 1 |
| Парткод: | G108 5108 |
| Деталь: | Harness -Paper Feed |
| Парткод: | M001 5406 |
| Деталь: | Push Sw - Paper Size |
| Парткод: | G800 3035 |
| Деталь: | Harness: Motor: Sensor |
| Парткод: | M001 5405 |
| Деталь: | Safety Switch Harness |
| Парткод: | G175 5410 |
| Деталь: | Control Board Bracket Assy |
| Парткод: | G096 1241 |
| Деталь: | Cover: EGB |
| Парткод: | M001 1156 |
| Деталь: | Support Plate Stay: Bypass |
| Парткод: | G096 3301 |
| Деталь: | Spacer - Paper Feed |
| Парткод: | G175 3138 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2075 |
| Деталь: | Auxiliary Ground Plate |
| Парткод: | G096 3337 |
| Деталь: | Bushing - 6x10x9mm |
| Парткод: | AA08 2058 |
| Деталь: | Paper Feed Ground Plate |
| Парткод: | G096 3335 |
| Деталь: | Interface Harness - FST |
| Парткод: | G175 5400 |
| Деталь: | Paper feed Shaft |
| Парткод: | G096 3101 |
| Деталь: | Paper Feed Stay |
| Парткод: | G096 3100 |
| Деталь: | Left Stay Cover |
| Парткод: | G096 3106 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | G029 2657 |
| Деталь: | Bushing - Paper Feed Roller |
| Парткод: | G052 3106 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | G052 3103 |
| Деталь: | Paper End Sensor Feeler |
| Парткод: | G096 3104 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Paper Volume Sensor Feeler |
| Парткод: | G096 3105 |
| Деталь: | Right Stay Cover |
| Парткод: | G096 3107 |
| Деталь: | Spring Plate - Paper Transport |
| Парткод: | G052 3304 |
| Деталь: | Paper Transport Roller |
| Парткод: | G052 3303 |
| Деталь: | Relay Roller |
| Парткод: | G175 3332 |
| Деталь: | Connecting Guide Roller |
| Парткод: | G096 3306 |
| Деталь: | Connecting Guide Plate |
| Парткод: | G096 3294 |
| Деталь: | Transport Guide Mylar |
| Парткод: | G052 3307 |
| Деталь: | Photointerruptor: LG248NL1 |
| Парткод: | GW02 0020 |
| Деталь: | Manual Feed Feeler |
| Парткод: | G175 3286 |
| Деталь: | Spring - Manual Feed |
| Парткод: | G096 3292 |
| Деталь: | Friction Pad - Manual Feed |
| Парткод: | G175 3290 |
| Деталь: | Paper Feed Roller: Manual Feed |
| Парткод: | G129 2552 |
| Деталь: | Feed Roller Cover |
| Парткод: | G175 2767 |
| Деталь: | Manual Feed Frame |
| Парткод: | G096 3280 |
| Деталь: | Screw: M3x13 |
| Парткод: | G116 4159 |
| Деталь: | Magnetic Clutch Stopper |
| Парткод: | G175 3139 |
| Деталь: | PAPER FEED CLUTCH |
| Парткод: | G175 2587 |
Коды ошибок
230
302
320
322
323
326
391
500
541
542
543
544
545
546
547
559
590
591
620
622
669
670
672
687
688
817
819
820
821
822
823
824
826
827
828
829
833, 834
838
851
853
854
855
856
857
860
861
863
864
865
866
867
868
870
872
873
874
875
876
880
900
920
990
991
995
Описание
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 320 |
| Display: | Reset fuser 320: Fuser error |
| Description: | Same unit not detected upon power ON or opening cover. |
| Causes: | 1) Is error message displayed? 2) Is fuser unit set properly? 3) Does error reoccur? |
| Remedy: | Check if fuser is set properly. Reset fuser and turn ON power again. Replace fuser unit assembly. |
| Error code: | 322 |
| Description: | Synchronization error The synchronization signal was not issued within 500 ms after the LD fired while the polygon motor was turning at the prescribed number of revolutions. |
| Causes: | • Laser synchronization board connectors or harness loose, disconnected, or damaged • Laser synchronization board defective or out of position • LD drive board defective |
| Remedy: | 1. Check the harness connection of the development HVPS. 2. Replace the development HVPS. 3. Replace the development unit. |
| Error code: | 323 |
| Display: | Open/close cover 323: Paper thickness error |
| Description: | Sensor output out of range with no media. (Only for Factory Mode) |
| Causes: | 1) Are foreign objects mixed in sensor? 2) Does printer recover when detecting paper thickness by opening/closing tray? 3) Does printer recover by power OFF/ON. |
| Remedy: | Remove foreign objects. Normal. |
| Error code: | 326 |
| Display: | Open/close cover 326: Paper thickness error |
| Description: | U-Heavy mode media detect value out of range. |
| Causes: | Is different media type mixed in? |
| Remedy: | Remove foreign objects. |
| Error code: | 391 |
| Description: | TD sensor error: Auto adjust error During automatic adjustment of the TD sensor, output voltage was less than 1.8V, or more than 4.8V during TD sensor initial setting |
| Causes: | • TD sensor connector or harness loose, broken, defective • TD sensor defective • IOB defective • Toner supply defective (confirm that the toner seal strip has been removed from toner cartridge) |
| Remedy: | 1. Check the harness or harness connection. 2. Clean the surface of the quenching lamp glass. |
| Error code: | 500 |
| Description: | Transport/Fusing Motor Error |
| Causes: | The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the transport/fusing motor. Replace it if necessary. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 590 |
| Description: | Toner collection motor error The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on. |
| Causes: | • Motor lock due to obstruction • Motor driver board defective • Motor connection loose, defective • Toner collection motor sensor disconnected, sensor defective • Rotational transmission shaft (o6 x 30) missing |
| Error code: | 591 |
| Description: | NC sensor broken: End The sensor detects -17°C or less for 6 seconds. |
| Causes: | Broken cables of thermopile. Broken cables of thermistor. Loose connection. |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 622 |
| Description: | Paper Bank communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The paper bank`s control board is faulty. Defective BCU/IOB. The paper bank`s connection is faulty. |
| Remedy: | • Reconnect the paper bank cables. • Replace the BCU. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 669 |
| Description: | EEPROM Error |
| Causes: | An unexpected value exists in the initialization flag of the EEPROM |
| Remedy: | • EEPROM not initialized • Defective EEPROM |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 688 |
| Description: | Ready notification error of image data transmission The controller does not send a ready notification of image data transmission after a sheet of paper has stopped at the registration roller. |
| Causes: | • Controller board defective • Communication error |
| Remedy: | • Turn the Power Switch Off and On. • Replace the engine board. |
| Error code: | 817 |
| Display: | SYSTEM HALT (*) 817 : FW/SaveArea |
| Description: | Monitor error This is a file detection and electronic file signature check error when the boot loader attempts to read the self-diagnostic module, system kernel, or root system files from the OS Flash ROM, or the items on the SD card in the controller slot are false or corrupted. |
| Causes: | OS Flash ROM data defective. SD card data defective. Change the controller firmware. Use another SD card. |
| Remedy: | • Change the controller firmware. • Use another SD card. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 833, 834 |
| Description: | For more details about SC 833, SC834 error. Execute SP5990 to print an SMC report so you can read the error code. The error code is not displayed on the operation panel. The additional error codes (0F30, 0F31, etc. are listed in the SMC report). |
| Error code: | 838 |
| Display: | SYSTEM HALT (*) 838 : FW/SV MDL |
| Description: | Self-diagnostic Error 10: Clock Generator A verify error occurred when setting data was read from the clock generator via the I2C bus. |
| Causes: | • Replace the controller board |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 995 |
| Description: | Finisher Main Feed Motor abnormal |
| Causes: | -01 D • Defective BCU • NVRAM Replacement error • Install the previous NVRAM • Input the serial number with SP5-811-004, and turn the main power switch off and on. -02 D • Defective NVRAM • Defective controller Perform SP5-825 to download the appropriate data to the NVRAM, and then turn the main power switch off and then back on. -03 D The serial number cannot be identified due to a mistake during controller replacement or mechanical failure. Replace the controller with the correct type. -04 D - Place all parts in the initial state, and then replace the parts according to the procedures described in the manuals. |
| Remedy: | 1 Is there jammed paper or other obstructions in the paper path? Clear the paper path. Go to step 2. 2 Check to ensure the connector PJ6 on the finisher control board and the feed motor assembly cable are properly connected. Are the cables properly connected? Go to step 3. Properly connect the cables. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pins 7 and 8 and +5 V dc (–10%) between pins 7 and 6 on the feed motor assembly cable connector CN1. Is either voltage missing? Go to step 4. Go to step 5. 4 Disconnect the feed motor assembly cable and PJ6 on the finisher control board. Measure continuity on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 5 Replace the feed motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 6 Measure for +24 V dc between pins 1 and 2 on connector PJ3 on the finisher control board. Measure for +5 V dc between pins 1 and 3 on PJ2 on the finisher control board. Is either voltage missing? Replace the power supply. Replace the finisher control board. |
