Ricoh SPC210SF

Рейтинг

Модули

PAPER EXIT SECTION

DOCUMENT FEED SECTION

LEFT SIDE PARTS

EXTERIOR

TOP AND RIGHT SIDE PARTS

CONSUMABLES

OPERATION PANEL

PAPER CASSETTE

FUSER UNIT

PAPER FEED & TRANSFER

Детали

Деталь:	Transfer Base Assy PU
Парткод:	V128 611

Деталь:	Transfer Roller Assy PU
Парткод:	V128 488

Деталь:	Exit Guide Assy PU
Парткод:	V128 489

Деталь:	Exit Idle Roller Assy PU
Парткод:	V128 492

Деталь:	Registration Actuator PU
Парткод:	V128 486

Деталь:	Exit Drive Assy PU
Парткод:	V128 494

Деталь:	Transfer Roller Guide PU
Парткод:	V128 495

Деталь:	Registration Roller Assy PU
Парткод:	V128 487

Деталь:	Paper Exit Actuator PU
Парткод:	V128 497

Деталь:	Exit Roller Assy PU
Парткод:	V128 490

Деталь:	Paper sensor
Парткод:	V126 167

Деталь:	Fuser Exit Actuator PU
Парткод:	V128 491

Деталь:	Discharge Brush
Парткод:	V123 842

Деталь:	DOCUMENT COVER ASSY
Парткод:	V121 300

Деталь:	HINGE ASSY L
Парткод:	V121 331

Деталь:	HINGE
Парткод:	V121 332

Деталь:	ADF Harness Unit
Парткод:	V121 345

Деталь:	Document Cover Sub
Парткод:	V121 301

Деталь:	Pressure Roller LF2
Парткод:	V121 302

Деталь:	PRESSURE SHAFT
Парткод:	V121 303

Деталь:	LF2 Spring
Парткод:	V121 304

Деталь:	EJECTION ROLLER B4
Парткод:	V121 305

Деталь:	Pressure Shaft EJ
Парткод:	V121 306

Деталь:	Ejection Spring
Парткод:	V121 307

Деталь:	HINGE ARM
Парткод:	V121 308

Деталь:	DOCUMENT STOPPER
Парткод:	V121 309

Деталь:	Lower Document Chute
Парткод:	V121 310

Деталь:	DRIVE FRAME ASSY
Парткод:	V121 311

Деталь:	ADF Motor - DC96W
Парткод:	V121 312

Деталь:	ADF Drive Gear Assy
Парткод:	V121 347

Деталь:	ADF Sensor PCB
Парткод:	V121 313

Деталь:	ACTUATOR R
Парткод:	V121 314

Деталь:	Actuator F
Парткод:	V121 315

Деталь:	EJECTION ROLLER ASSY
Парткод:	V121 316

Деталь:	Ejection Bearing
Парткод:	V121 317

Деталь:	LF ROLLER ASSY
Парткод:	V121 318

Деталь:	Resin Bearing
Парткод:	V121 319

Деталь:	Document Hold
Парткод:	V121 320

Деталь:	DOCUMENT HOLD SPRING
Парткод:	V121 321

Деталь:	UPPER DOCUMENT CHUTE ASSY
Парткод:	V121 322

Деталь:	SEPARATION RUBBER ASSY
Парткод:	V121 323

Деталь:	Separate Shaft
Парткод:	V121 324

Деталь:	Separate Roller Gear
Парткод:	V121 325

Деталь:	Bushing 6N
Парткод:	V121 326

Деталь:	Gaer Cover
Парткод:	V121 327

Деталь:	ADF Cover
Парткод:	V121 328

Деталь:	LF SPRING
Парткод:	V121 329

Деталь:	Pressue Roller
Парткод:	V121 330

Деталь:	Belt Sensor
Парткод:	V126 168

Деталь:	HV Power Supply PU
Парткод:	V128 451

Деталь:	LV Power Supply (110V) RoHS
Парткод:	V128 675

Деталь:	LV Power Supply (220V) RoHS
Парткод:	V128 676

Деталь:	Power Supply Bracket (110V) PU
Парткод:	V128 612

Деталь:	Power Supply Bracket (220V) PU
Парткод:	V128 613

Деталь:	Interlock Switch PU
Парткод:	V128 436

Деталь:	Fuser Connector (110V) PU
Парткод:	V128 457

Деталь:	Fuser Connector (220V) PU
Парткод:	V128 458

Деталь:	Toner Retoract Solenoid PU
Парткод:	V128 459

Деталь:	Toner Retoract Cam PU
Парткод:	V128 460

Деталь:	TONER SENSOR ASSY
Парткод:	V126 169

Деталь:	Toner Present Sensor PU
Парткод:	V128 461

Деталь:	TOP COVER ASSY
Парткод:	V121 266

Деталь:	Top Side L
Парткод:	V121 272

Деталь:	Top Side R
Парткод:	V121 273

Деталь:	Side Cover LR
Парткод:	V121 274

Деталь:	Side Cover LF Assy
Парткод:	V121 275

Деталь:	MFC Controller Board (US)
Парткод:	V121 284

Деталь:	MFC Controller Board (EC)
Парткод:	V121 285

Деталь:	Scanner Arm L
Парткод:	V121 267

Деталь:	Scanner Arm R
Парткод:	V121 268

Деталь:	NCU Boad (US)
Парткод:	V121 287

Деталь:	NCU Boad (ASA)
Парткод:	V121 288

Деталь:	NCU Boad (OCE)
Парткод:	V121 289

Деталь:	NCU Boad (EUR)
Парткод:	V121 290

Деталь:	IS Lock Lever Assy
Парткод:	V121 269

Деталь:	Tray (TP)
Парткод:	V121 270

Деталь:	Top Center Cover Assy
Парткод:	V121 271

Деталь:	Knur Biss with Groove 2
Парткод:	V121 299

Деталь:	Is Lift Spring R2
Парткод:	V121 297

Деталь:	Nickel Hydride Battery(EX)
Парткод:	V121 277

Деталь:	Engine Controller Board MSL1
Парткод:	V121 278

Деталь:	Heater Fan Assy
Парткод:	V121 279

Деталь:	SPEAKER
Парткод:	V121 280

Деталь:	Inter Lock Assy
Парткод:	V121 281

Деталь:	Scanner Door Sensor
Парткод:	V126 167

Деталь:	REAR COVER ASSY
Парткод:	V121 282

Деталь:	Laser Assy MSL
Парткод:	V121 283

Деталь:	FRONT DOOR ASSY
Парткод:	V121 298

Деталь:	Power Supply Fan Assy
Парткод:	V121 292

Деталь:	Harness Guide S
Парткод:	V121 293

Деталь:	Scanner Slider L
Парткод:	V121 294

Деталь:	Scanner Slider R
Парткод:	V121 295

Деталь:	Is Lift Spring L2
Парткод:	V121 296

Деталь:	Right Side Cover PU
Парткод:	V128 417

Деталь:	Inner Front Cover PU
Парткод:	V128 419

Деталь:	Main Motor PU
Парткод:	V128 423

Деталь:	OPC Drive Gear Assy PU
Парткод:	V128 424

Деталь:	Paper Feed Clutch PU
Парткод:	V128 425

Деталь:	Registration Clutch PU
Парткод:	V128 426

Деталь:	Fuser Clutch PU
Парткод:	V128 427

Деталь:	TR Cam Clutch 3
Парткод:	V126 639

Деталь:	Cleaning Roller Clutch PU
Парткод:	V128 428

Деталь:	Main Drive Gear Assy PU
Парткод:	V128 429

Деталь:	Waste Toner Feeder PU
Парткод:	V128 430

Деталь:	Developer Motor PU
Парткод:	V128 431

Деталь:	Developer Drive Assy PU
Парткод:	V128 432

Деталь:	Developer Gear PU
Парткод:	V128 433

Деталь:	Developer Clutch PU
Парткод:	V128 434

Деталь:	Waste Toner Holder Assy PU
Парткод:	V128 435

Деталь:	Interlock Switch PU
Парткод:	V128 436

Деталь:	Right Tray Guide PU
Парткод:	V128 438

Деталь:	Left Tray Guide PU 2
Парткод:	V128 648

Деталь:	Paper Size Sensor PU
Парткод:	V128 440

Деталь:	Room Temp. Thermistor PU
Парткод:	V128 441

Деталь:	Right Toner Guide PU
Парткод:	V128 442

Деталь:	Left Toner Guide PU
Парткод:	V128 443

Деталь:	Waste Toner Auger PU
Парткод:	V128 444

Деталь:	Waste Toner Agitator PU
Парткод:	V128 446

Деталь:	Laser Unit Fan Assy PU
Парткод:	V128 447

Деталь:	F Switch Base PU
Парткод:	V128 448

Деталь:	OPC Carger Roller PU
Парткод:	V128 403

Деталь:	Cleaning Roller PU
Парткод:	V128 404

Деталь:	Cleaning Roller Cover PU
Парткод:	V128 664

Деталь:	Fusing Unit (110V) FU
Парткод:	V128 622

Деталь:	Fusing Unit (220V) FU
Парткод:	V128 623

Деталь:	Power Cord (EC)
Парткод:	V121 265

Деталь:	Power Cord (110 V) PU
Парткод:	V128 409

Деталь:	Users Guide - US English
Парткод:	G157 3104

Деталь:	Quick Setup Guide - US English
Парткод:	G157 3004

Деталь:	Front Band PU
Парткод:	V128 449

Деталь:	Plate - Logo RIC
Парткод:	G139 2690

Деталь:	Decal - Aficio SPC210SF
Парткод:	G157 5051

Деталь:	Telephone Cable (US Only)
Парткод:	H523 5350

Деталь:	Sanner Unit (SP) With out ADF
Парткод:	V121 346

Деталь:	Rubber Button Pad-Operation Panel
Парткод:	V121 336

Деталь:	PANEL PCB ASSY
Парткод:	V121 337

Деталь:	LCD Backlight Module
Парткод:	V121 338

Деталь:	LCD
Парткод:	V121 339

Деталь:	LCD COVER
Парткод:	V121 340

Деталь:	Panel Cover Assy, For US
Парткод:	V121 341

Деталь:	Panel Cover (ASA/OCE)
Парткод:	V121 343

Деталь:	Panel Cover EC
Парткод:	V121 344

Деталь:	Transfer Unit PU
Парткод:	V128 463

Деталь:	Paper Guide (A) PU
Парткод:	V128 464

Деталь:	Paper Guide (B) PU
Парткод:	V128 465

Деталь:	Paper sensor
Парткод:	V126 167

Деталь:	Paper Feeding Roller
Парткод:	V126 142

Деталь:	Separator Pad (2)
Парткод:	V128 468

Деталь:	Erase Lamp PU
Парткод:	V128 469

Деталь:	Paper Guide (D) PU
Парткод:	V128 470

Деталь:	Toner Density Sensor PU
Парткод:	V128 471

Деталь:	Belt Sensor
Парткод:	V126 168

Деталь:	OHP Sensor 3
Парткод:	V126 648

Деталь:	Paper Guide (C) PU
Парткод:	V128 466

Деталь:	Tray Empty Actuator PU
Парткод:	V128 467

Деталь:	Sensor Stay Assy PU
Парткод:	V128 472

Деталь:	TR Unit Band
Парткод:	V128 498

Коды ошибок

090

110

111

112

113

140

141

160

180

25#

251

411

412

Описание

Парткод

Название

RICOH TYPE 140 Блок формирования изображения

RICOH TYPE 140 Туба для отработанного тонера

RICOH TYPE 140 Тонер-картридж черный

RICOH TYPE 140 Тонер-картридж голубой

RICOH TYPE 140 Тонер-картридж пурпурный

RICOH TYPE 140 Тонер-картридж желтый

Деталь:	Fuser Connector (110V) FU
Парткод:	V128 477

Деталь:	Fuser Connector (220V) FU
Парткод:	V128 478

Error code:	090
Display:	SVC 090 ERROR
Description:	Check sum error
Causes:	1. HVPS is defective. 2. Drum cartridge defective.
Remedy:	Replace the Controller board.

Error code:	11
Display:	ERROR CONDITION CUTTER JAM
Description:	The printer stops; the ERROR light flashes.
Causes:	Caution • The cutter blade is sharp. Do not touch or rub the blade with your fingers. The cutter blade is in the media path.
Remedy:	Turn off the printer power and unplug the printer. Inspect the cutter module for debris and clean as needed following the cleaning instructions in Clean the Cutter Module on page 135.

Error code:	110
Display:	SVC 110 ERROR
Description:	Printhead Error
Causes:	Incorrect color DTM installation, incorrect PCU installation, development bias error, MCU, LD control malfunction, loss of synchronization
Remedy:	No first Hysnc - cyan Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J8 and J9 on the system board. Go to “System board” on page 5-8. If the cables are connected correctly to the system board and to the printhead assembly, replace the “Printhead diagnostics”. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics”

Error code:	111
Display:	SVC 111 ERROR
Description:	Printhead Error
Causes:	Incorrect color DTM installation, incorrect PCU installation, development bias error, MCU, LD control malfunction, loss of synchronization
Remedy:	No first Hysnc - magenta Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J11 and J12 on the system board. Go to “System board”. If the cables are connected correctly to the system board and to the printhead assembly, go to “Printhead diagnostics”

Error code:	112
Display:	SVC 112 ERROR
Description:	Printhead Error
Causes:	Incorrect color DTM installation, incorrect PCU installation, development bias error, MCU, LD control malfunction, loss of synchronization
Remedy:	No first Hysnc - yellow Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J7 and J8 on the system board. Go to “System board”. If the cables are connected correctly to the system board and to the printhead assembly, go to “Printhead diagnostics”. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics”

Error code:	113
Display:	SVC 113 ERROR
Description:	Finisher Stapler Failure, Code 113 The staple home sensor doesn’t turn ON within 2 seconds after the stapler motor started to turn backwards.
Causes:	• Finisher Control Board • Staple Unit Assembly
Remedy:	1 1. Enter service diagnostics. 2. Run the Stapler Home sensor test. 3. Does the value change from H to L when the stapler is moved away from the home position? Go to step 6. Go to step 2. 2 1. Measure the voltage between finisher board connector P852-2 and frame ground. 2. Does the voltage change between 0 and +5 VDC when the sensor is blocked and unblocked? Replace the finisher control board. Go to step 3. 3 1. Measure the voltage at the Finisher Board connector P852-1. 2. Dose the voltage measure +5 VDC? The home sensor or the wiring is bad. Replace the staple unit assembly. Go to step 4. 4 1. Disconnect the Stapler Unit Assembly. 2. Measure the voltage between the finisher board connector P852-1 and frame ground. 3. Does the voltage measure +5 VDC? Replace the stapler unit assembly. Go to step 5. 5 Is +24 VDC present at either J847-7 or J847-9? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. 6 1. Enter service diagnostics and run the “Stapler Close Motor” test. 2. Does the stapler motor operate correctly? Replace the finisher control board. Go to step 7. 7 With the Stapler Close Motor test running is +24 VDC present at J847-7? Replace in the following order: • stapler head assembly • finisher control board Troubleshoot and repair the +24 VDC interlock circuit.

Error code:	140
Display:	SVC 140 ERROR
Description:	Motor
Remedy:	DC motor accel stall - staging - replace the Staging motor. If this does not fix the problem, replace the “System board”

Error code:	141
Display:	SVC 141 ERROR
Description:	Motor
Causes:	• SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective
Remedy:	DC pick motor excessive PWM - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”

Error code:	160
Display:	SVC 160 ERROR
Description:	Tray and Media Errors When a tray is pulled out that prevents printing during a print job, an error condition exists.When a tray is pulled out while no job is printing or that does not prevent printing during a print job, a warning condition exists.
Causes:	• Paper Size Switch, PL3.2.5 • Paper Tray, PL2.1.1
Remedy:	1 Check the following for evidence of fault or damage: • Tray 2 Paper Size Switch, PL3.2.5 • Tray 2 Paper Size Switch Actuators, PL2.1.10 • Paper Tray, PL2.1.1 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Test the Tray 2 Paper Size Switches. Run the Service Diagnostics Paper Size Switch test. Use the table on. Do the switches function correctly? Replace the Engine Control Board. Go to Step 3. 3 Check the Paper Size Switch signals. 1. Disconnect P/J47. 2. Verify +3.3 V on pins P/J47-1 <=> P47-3 P/J47-2 <=> P47-3 P/J47-4 <=> P47-3 Is there +3.3 V when actuated? Go to Step 4 Replace the Paper Size Switch. 4 Check all pins on the FDR Harness for continuity. 1. Disconnect P/J47 and P/J471. 2. Check continuity between J47 <=> J471. Replace the Engine Control Board. Replace the FDR Harness.

Error code:	180
Display:	SVC 180 ERROR
Description:	I/F Error, Loc: Envelop feeder
Causes:	• Fan, MCU, SIB harnesses loose or defective • Scanner intake fan motor defective • MCU defective • SIB defective
Remedy:	Replace the Controller board.

Error code:	25#
Display:	SVC 25# ERROR
Description:	DMA circuit test error
Remedy:	Replace the Controller board.

Error code:	251
Display:	SVC 251 ERROR
Description:	DMA circuit cut-in error
Causes:	• Disconnected or defective harness to synchronizing detector for start position • Defective laser synchronizing detector for start position • Defective LDB
Remedy:	Replace the Controller board.

Error code:	31
Description:	The LCD is missing characters or parts of characters
Causes:	The LCD may need replacing.
Remedy:	Run the Power-On Self Test on page 117 and check that the LCD display shows all characters. If not, replace the LCD.

Error code:	32
Description:	Changes in parameter settings did not take effect
Causes:	Parameters are set incorrectly. A command turned off the ability to change the parameter. A command changed the parameter back to the previous setting. If the problem continues, there may be a problem with the main logic board.
Remedy:	1. Set parameters and save permanently. 2. Turn the printer off (O) and then on (I). Refer to the ZPL Programming Guide. Refer to the ZPL Programming Guide. Replace the main logic board.

Error code:	33
Description:	The printer fails to calibrate or detect the top of the label.
Causes:	The printer was not calibrated for the label being used. The printer is configured for continuous media. The driver or software configuration is not set correctly.
Remedy:	Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81. Driver or software settings produce commands that can overwrite the printer configuration. Check the driver or software media-related setting.

Error code:	41
Display:	Self Diagnostic LSU
Description:	Install or Reseat Fuser, Code 41 Front thermistor open error. This is a cold condition. Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault is performed.
Causes:	• Fuser • Engine Control Board
Remedy:	1 1. Turn OFF power and remove the Fuser Assembly. 2. Measure the resistance between the fuser connector P600-4 and P600-6. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 2. Replace the fuser assembly. 2 1. Reinstall the fuser assembly. 2. Enter service diagnostics. 3. From the Sensor Tests run the Fuser Temperature test. 4. Is the temperature indicated approximately 165o C? Replace the engine control board. Go to step 3. 3 1. Turn OFF printer power. 2. Check for an open circuit or poor connection between J600-4 to J600-6 to J404A-2. 3. Is the wiring OK? Replace the engine control board. Repair or replace the wiring harness.

Error code:	411
Display:	SVC 411 ERROR
Description:	IRQ timer 1 error
Causes:	• ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn
Remedy:	Replace the Controller board.

Error code:	412
Display:	SVC 412 ERROR
Description:	IRQ timer 2 error
Causes:	• ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn
Remedy:	Replace the Controller board.

Ricoh SPC210SF

Модули

Детали

Коды ошибок

Описание

Парткод

Название

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Error code:	42
Display:	Self Diagnostic Temperature
Description:	10-352 ERROR 42 FUSER STS (FRONT) WARM TIME FAILURE
Causes:	1. The ‘Open Cover’ microswitch may be stuck or faulty 2. The tab on the front cover may be damaged or broken 3. Check the connector and cables between Switch and main PBA.
Remedy:	Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board.

Error code:	43
Display:	Send Error (AUTH)
Description:	10-353 ERROR 43 FUSER SSR1 ON TIME FAILURE
Causes:	1. The ‘Open Cover’ microswitch may be stuck or faulty 2. Check the connector and cables between Switch and main PBA.
Remedy:	Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board.

Error code:	61
Display:	Nongenuine Toner Replace Toner 1
Description:	The toner cartridge installed is not a genuine cartridge.
Causes:	The printer warms up when the printer is turned on or the cover is closed, or wake from sleep mode.
Remedy:	This message appears when you selected stop at the Non Genuine Toner prompt. Install the genuine toner cartridge.

Error code:	C3
Display:	SVC C3 ERROR
Description:	PF jam cass.3
Causes:	• If the actuator of the Master removal unit safety switch is not depressed.
Remedy:	This may happen in some cases of bad line condition. Ask the remote party to transmit again.

Error code:	C4
Display:	SVC C4 ERROR
Description:	Machine has reset
Causes:	• If the master disposal box set sensor does not detect.
Remedy:	This may happen in some cases of bad line condition. Ask the remote party to transmit again.

Error code:	C7
Display:	SVC C7 ERROR
Description:	Error C7
Causes:	• If the Master removal 5 times.
Remedy:	1. Check if any thermistor connector is disconnected. 2. Check if any harness of the thermistors (center/rear, upper/lower) is open-circuited. 3. Check the LGC board if the connector J122 is disconnected. 4. After completing the repair of what caused the [C7] problem, proceed to rewrite the status counter (08-700) to "0", following the same procedure as for [C41] to [C48] .

Error code:	D1
Display:	SVC D1 ERROR
Description:	Jam at Door D Open Door D to Clear Media reached Duplex Reverse Sensor, but did not leave the Duplex Unit on time. This error represents a misfeed jam inside the Duplex Unit.
Causes:	• Duplex Unit, PL16.1.0
Remedy:	1 Check the following for evidence of fault or damage: • Duplex Unit Entrance Roller • Duplex Unit Connector • Duplex Unit Is there any damage or debris? Replace any damaged parts. Go to Step 2. 2 Test the Duplex Entrance, Reverse, Front, and Rear actuators and sensors using Service Diagnostics. Do the sensors and actuators function correctly? Go to Step 3. Replace the Duplex Unit. 3 Test the Duplex Motors using Service Diagnostics. Do the motors function correctly? Go to Step 4. Replace the Duplex Unit. 4 Inspect the DUPLEX harness. If defective, replace the wiring harness. Is the harness properly seated and free from defects? Replace the Motor Driver Board. Replace the Duplex Unit.

Error code:	D2
Display:	SVC D2 ERROR
Description:	Jam in Duplex Unit Media reached Duplex Reverse Sensor, but did not leave the Duplex Unit on time. This error represents a misfeed jam inside the Duplex Unit.
Causes:	• Duplex Unit, PL16.1.0
Remedy:	1 Ensure the correct weight and type of paper is loaded in the tray. Does the media meet specifications? Go to Step 2. Run several test prints. If a jam persists, go to Step 2. 2 Check for and remove any dirt, debris or obstructions in the paper path around the Duplex Unit. Did this correct the problem? Complete Go to Step 3. 3 Clean and check the Duplex Unit rollers. Do the rollers move freely and are free of dirt or debris? Go to Step 4. Replace the Duplex Unit. 4 Test the Duplex Entrance, Reverse, Front, and Rear actuators and sensors using Service Diagnostics. Do the sensors function correctly? Go to Step 5. Replace the Duplex Unit. 5 Test the Duplex Motors. Do the motors function correctly? Go to Step 6. Replace the Duplex Unit. 6 Inspect the DUPLEX harness. If defective, replace the wiring harness. Is the harness properly seated and free from defects? Replace the Motor Driver Board. Replace the Duplex Unit.

Error code:	E0
Display:	SVC E0 ERROR
Description:	Machine has reset
Causes:	• Error with CPU and gate arrays of either the engine or main controller • Connection error between the engine board and the main controller board • Program overrun in the engine or main controllere
Remedy:	Remove the cause of the printer error, then ask the remote party to transmit again.

Error code:	E1
Display:	SVC E1 ERROR
Description:	Jam at Door E Paper misfeed jam between the Fuser and the Top Output Tray. Media reached the Fuser Exit Sensor, but did not reach the Top Output Tray Stack Full Sensor on time. This error represents a misfeed jam inside the Exit Assembly.
Causes:	• Exit Assembly, PL11.1.0 • Fuser Motor, PL2.1.9 • Exit Gate Solenoid, PL11.1.17 • Full Stack Sensor, PL11.1.39
Remedy:	1 Check the following for evidence of fault or damage: • Door E • Fuser • Exit Rollers and drive gears • Stack Full Actuator • Exit Assembly Is there any damage or debris? Replace any damaged parts. Go to Step 2. 2 Test the Fuser Exit and Top Output Tray Stack Full Sensors. Do the sensors function correctly? Go to Step 4. Replace the sensor. If the error persists, go to Step 3. 3 Check all pins on the SNS Harness for continuity. Is the harness conductive? Go to Step 4. Replace the SNS Harness. 4 Test the Fuser Motor. Run the Service Diagnostics Fuser Motor test. Does the motor function correctly? Go to Step 6. Replace the motor. If the error persists, go to Step 5. 5 Check for +24 V to the Fuser Motor. Disconnect DCHEAT on the Motor Driver Board. Is there +24 V across DCHEAT-3 <=> ground? Go to Step 6. Replace the Motor Driver Board. If the error persists, go to Step 6. 6 Test the Exit Gate Solenoid. Run the Service Diagnostics Exit Gate Solenoid test. Does the solenoid function correctly. Go to Step 8. Replace the solenoid. If the error persists, go to Step 7. 7 Check for +24 V to the solenoid. 1. Actuate the interlock switches. 2. Disconnect SOLENOID from the Rear Sensor Board. Is there +24 V across SOLENOID-1 <=> ground? Go to Step 8. Replace the Rear Sensor Board. 8 Check the DRV0 and DRV1 ribbon cables that connect the Motor Driver Board to the Engine Control Board. Are these cables connected and undamaged? Replace the Engine Control Board. Replace the harnesses.