Ricoh SPC811DN
Рейтинг
Модули
ELECTRICAL SECTION 2
DRIVE SECTION 4
By-pass Feed Section 2
2nd Paper Tray
EXTERIOR 2
PAPER EXIT SECTION 2
ELECTRICAL SECTION 3
Drive Section 5
DUPLEX UNIT 4
LD unit
Drive Section 1
Paper Separation
Frame Section 4
By-pass Feed Section 1
PAPER EXIT SECTION 1
ACCESSORIES
ELECTRICAL SECTION 4
ELECTRICAL SECTION 1
EXTERIOR 3
EXTERIOR 1
PAPER FEED SECTION
DUPLEX UNIT 2
DRIVE SECTION 3
DUPLEX UNIT 1
TONER SUPPLY UNIT 2
DUPLEX UNIT 3
FUSING UNIT 2
FUSING UNIT 1
PAPER REGISTRATION
Toner Supply Unit 1
FRAME SECTION 2
FRAME SECTION 1
FUSING UNIT 3
DUPLEX UNIT 5
1st Paper Tray
Frame Section 3
DRIVE SECTION 2
Детали FUSING UNIT 2
| Деталь: | Hinge:Panel:Control Board |
| Парткод: | B223 5812 |
| Деталь: | Gasket:Egun1-0205:L23 |
| Парткод: | B223 5863 |
| Деталь: | PCB:EGB:AP-P:ASSY |
| Парткод: | G133 5162 |
| Деталь: | Harness:IPU:LD-Signal:2LD |
| Парткод: | B223 5244 |
| Деталь: | Harness:IPU:LD-Data:2LD |
| Парткод: | B223 5246 |
| Деталь: | Harness:IPU:Sync Detector:Mirror |
| Парткод: | B223 5248 |
| Деталь: | Harness:IOB:EGB |
| Парткод: | G133 5327 |
| Деталь: | Harness:EGB:TM/P:Sensor |
| Парткод: | G133 5328 |
| Деталь: | Harness:Power Supply Unit |
| Парткод: | G133 5343 |
| Деталь: | Feed Drive Shaft |
| Парткод: | B223 1189 |
| Деталь: | Grip Shaft |
| Парткод: | B223 1183 |
| Деталь: | Drive Joint |
| Парткод: | B223 1186 |
| Деталь: | Drum Stay:Drive Unit |
| Парткод: | B223 1354 |
| Деталь: | Gear - 33Z/44Z |
| Парткод: | AB01 7699 |
| Деталь: | Gear - 38Z |
| Парткод: | AB01 1258 |
| Деталь: | Timing Belt:40S3M162 |
| Парткод: | AA04 3585 |
| Деталь: | Timing Pulley - 28Z/30T |
| Парткод: | AB03 0781 |
| Деталь: | Gear - 32Z |
| Парткод: | AB01 1259 |
| Деталь: | Bracket:Paper Feed |
| Парткод: | B223 1180 |
| Деталь: | Magnetic Clutch - 32Z |
| Парткод: | AX20 0289 |
| Деталь: | Magnetic Clutch Bracket |
| Парткод: | B223 1187 |
| Деталь: | BUSHING - 6MM |
| Парткод: | GA08 0002 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Cushion:Stepper Motor |
| Парткод: | AA16 1164 |
| Деталь: | Stepper Motor DC24V |
| Парткод: | B223 1188 |
| Деталь: | Temperature & Humidity Sensor |
| Парткод: | AW14 0012 |
| Деталь: | Timing Belt - B40S2M118 |
| Парткод: | AA04 3601 |
| Деталь: | Timing Pulley - 27Z/40T |
| Парткод: | AB03 0744 |
| Деталь: | Bracket:Drive Unit:Registration |
| Парткод: | B223 1191 |
| Деталь: | Cushion - Stepper Motor |
| Парткод: | A232 4666 |
| Деталь: | Stepper Motor DC5.06V |
| Парткод: | B223 1350 |
| Деталь: | Harness:IOB:Motor |
| Парткод: | B223 5307 |
| Деталь: | Cover:Guide Plate:Exit |
| Парткод: | B223 2623 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Guide Plate:Exit |
| Парткод: | B223 2622 |
| Деталь: | Cover:Manual Feed Unit |
| Парткод: | B223 2621 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | Feed Roller - Manual Feed |
| Парткод: | AF03 1046 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Shaft:Feed |
| Парткод: | AA14 0777 |
| Деталь: | Stay:Feed |
| Парткод: | B223 2629 |
| Деталь: | Gear - 23Z |
| Парткод: | AB01 1387 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | AF03 0049 |
| Деталь: | SPRING:PRESSURE:PICKUP |
| Парткод: | AA06 3568 |
| Деталь: | Pick-up Arm - Manual Feed |
| Парткод: | G060 2932 |
| Деталь: | DC Solenoid:Pickup |
| Парткод: | B223 2632 |
| Деталь: | Spring:Release:Pickup |
| Парткод: | B223 2633 |
| Деталь: | Harness:Manual Feed |
| Парткод: | B223 2659 |
| Деталь: | Sheet:Guide:Exit |
| Парткод: | B223 2624 |
| Деталь: | Transport Roller:Exit:Duplex |
| Парткод: | B223 2619 |
| Деталь: | Support Stay:Arm |
| Парткод: | B223 2634 |
| Деталь: | Torsion Spring:27n |
| Парткод: | B223 2636 |
| Деталь: | Paper End Sensor |
| Парткод: | AW50 0035 |
| Деталь: | Arm:Manual Feed:Front |
| Парткод: | B223 2651 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2102 |
| Деталь: | Arm:Manual Feed:Short:Front |
| Парткод: | B223 2657 |
| Деталь: | Ground Plate:Reverse |
| Парткод: | B223 2607 |
| Деталь: | Guide Plate:Separator |
| Парткод: | B223 2609 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3016 |
| Деталь: | Bushing:Feed |
| Парткод: | G080 2682 |
| Деталь: | Ground Plate:Rear |
| Парткод: | B223 2606 |
| Деталь: | One-way Clutch |
| Парткод: | AA08 3014 |
| Деталь: | Magnetic clutch |
| Парткод: | AX20 2007 |
| Деталь: | Bracket:Arm:Manual Feed:Rear |
| Парткод: | B223 2637 |
| Деталь: | Arm:Manual Feed:Rear |
| Парткод: | B223 2652 |
| Деталь: | Arm:Manual Feed:Short:Rear |
| Парткод: | B223 2658 |
| Деталь: | Bushing - 6 6mm |
| Парткод: | A259 6754 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1416 |
| Деталь: | Gear:Z16 |
| Парткод: | B223 2608 |
| Деталь: | Shaft:Separator:Drive |
| Парткод: | AA14 0778 |
| Деталь: | Separation Roller - Manual Feed |
| Парткод: | AF03 2046 |
| Деталь: | TORQUE LIMITER |
| Парткод: | G080 2900 |
| Деталь: | Shaft:Separator:Driven:Assy |
| Парткод: | B180 2871 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3499 |
| Деталь: | SPRING |
| Парткод: | AA06 0872 |
| Деталь: | Arm:Tightener |
| Парткод: | B223 2681 |
| Деталь: | Idler Gear - 25z |
| Парткод: | AB01 1223 |
| Деталь: | Gear:Z31 |
| Парткод: | B223 2686 |
| Деталь: | Gear:25Z |
| Парткод: | B223 2683 |
| Деталь: | Gear:Z28 |
| Парткод: | B223 2689 |
| Деталь: | Drum Stay:Drive |
| Парткод: | B223 2696 |
| Деталь: | Paper Tray:No.2:Assy |
| Парткод: | B223 2901 |
| Деталь: | Link - Paper Size Sensor |
| Парткод: | B223 2910 |
| Деталь: | SPACER |
| Парткод: | B223 2911 |
| Деталь: | Decal - Paper Set Direction No.2 |
| Парткод: | B238 2523 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B223 2940 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3006 |
| Деталь: | Tension Spring:Side Fence:Rear |
| Парткод: | AA06 1003 |
| Деталь: | Cover - Paper Tray No.2 |
| Парткод: | B223 2946 |
| Деталь: | Paper Tray Grip |
| Парткод: | B223 2860 |
| Деталь: | Decal - Grip |
| Парткод: | B238 2527 |
| Деталь: | Lever - Release Inner |
| Парткод: | B223 2862 |
| Деталь: | Tension Spring:Grip |
| Парткод: | AA06 1014 |
| Деталь: | Release Shaft |
| Парткод: | B223 2863 |
| Деталь: | Grip Holder |
| Парткод: | B223 2861 |
| Деталь: | Ground Plate - Paper Tray No.2 |
| Парткод: | B223 2919 |
| Деталь: | LEVER:RELEASE:PAPER TRAY:OUTER |
| Парткод: | B223 2868 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | END FENCE |
| Парткод: | B223 2912 |
| Деталь: | Front Side Fence |
| Парткод: | B223 2920 |
| Деталь: | Stopper Lever - Front |
| Парткод: | B223 2923 |
| Деталь: | Spring Plate - Release Lever |
| Парткод: | B004 2923 |
| Деталь: | Plate - Side Fence Right |
| Парткод: | B223 2935 |
| Деталь: | Plate - Side Fence |
| Парткод: | B223 2934 |
| Деталь: | Gear - 16Z |
| Парткод: | B223 2936 |
| Деталь: | Rise No.1 Shaft |
| Парткод: | B223 2865 |
| Деталь: | Rise Lever |
| Парткод: | B223 2918 |
| Деталь: | Rear Side Fence |
| Парткод: | B223 2930 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A267 2860 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Decal - Side Fence Rear |
| Парткод: | B223 2873 |
| Деталь: | Decal - Main Switch(on-off) |
| Парткод: | B238 1372 |
| Деталь: | Decal:Caution:Inkjet:NA |
| Парткод: | GA00 3167 |
| Деталь: | Cover:Front Right:P:EU |
| Парткод: | G133 1274 |
| Деталь: | Cover:Right:Front:EU |
| Парткод: | B222 1271 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | G133 1405 |
| Деталь: | Harness:Operation Panel |
| Парткод: | G146 5740 |
| Деталь: | EXIT TRAY |
| Парткод: | B223 4486 |
| Деталь: | Exit End Fence |
| Парткод: | B223 4487 |
| Деталь: | MAGNET CATCH |
| Парткод: | AA02 1030 |
| Деталь: | Collection Bottlecover - Front |
| Парткод: | B223 1254 |
| Деталь: | Cover:Upper |
| Парткод: | B223 1260 |
| Деталь: | Cover:Inner Back:P |
| Парткод: | G133 1261 |
| Деталь: | Cover:Inner Back:Middle:P |
| Парткод: | G133 1263 |
| Деталь: | Cover:Paper Exit Unit:Upper |
| Парткод: | G133 1266 |
| Деталь: | Inner Cover - Left |
| Парткод: | B223 1242 |
| Деталь: | Cover:Upper:Rear |
| Парткод: | G133 1267 |
| Деталь: | Cover:Upper:Right |
| Парткод: | G133 1268 |
| Деталь: | Cap:Dia17 |
| Парткод: | G133 1269 |
| Деталь: | Overflow Feeler |
| Парткод: | B238 4987 |
| Деталь: | Overflow Feeler Shaft |
| Парткод: | B238 4985 |
| Деталь: | EXIT ROLLER |
| Парткод: | B223 4453 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Ground Plate:Bracket:Sensor |
| Парткод: | B223 4427 |
| Деталь: | Discharge Brush:Exit |
| Парткод: | B223 4491 |
| Деталь: | Guide Plate:Upper Left |
| Парткод: | B223 4421 |
| Деталь: | BUSHING - M4 |
| Парткод: | H053 2208 |
| Деталь: | Transport Roller:Auxiliary |
| Парткод: | B223 4455 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Timing Belt:30S2M160 |
| Парткод: | AA04 3968 |
| Деталь: | Gear:Pulley:Z27/T22 |
| Парткод: | B223 4457 |
| Деталь: | Timing Pulley:22T |
| Парткод: | B223 4463 |
| Деталь: | Roller:Auxiliary:Driven:Dia16:pFA |
| Парткод: | B223 4435 |
| Деталь: | Shaft:Pressure:Auxiliary |
| Парткод: | B223 4493 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0156 |
| Деталь: | Compression Spring - Driven Roller |
| Парткод: | B238 4458 |
| Деталь: | Roller:Guide:pFA |
| Парткод: | B223 4428 |
| Деталь: | Guide Plate:Lower |
| Парткод: | B223 4488 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0567 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0566 |
| Деталь: | Spring Plate - Exit Roller Outer |
| Парткод: | B238 4436 |
| Деталь: | Spring Plate - Exit Roller |
| Парткод: | B223 4436 |
| Деталь: | Sensor bracket |
| Парткод: | B238 4454 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0127 |
| Деталь: | Stay:Protect |
| Парткод: | B223 4442 |
| Деталь: | Bracket:Sw:Dehumidifier:Heater:Exp |
| Парткод: | B223 5857 |
| Деталь: | Duct:Rear:Lower |
| Парткод: | B223 1239 |
| Деталь: | Gasket:Etnw100-00505:L90 |
| Парткод: | B223 5861 |
| Деталь: | Power Supply Unit:494W:DOM/NA |
| Парткод: | AZ24 0109 |
| Деталь: | Power Supply Unit:494W:EU/AA:APO-C1 |
| Парткод: | AZ24 0110 |
| Деталь: | Harness:PSU:JIGU |
| Парткод: | B223 5336 |
| Деталь: | Harness:Power Supply Unit |
| Парткод: | G133 5346 |
| Деталь: | Harness:PSU:SW:NA |
| Парткод: | B223 5332 |
| Деталь: | Harness:AC:IH:Power Supply Unit |
| Парткод: | B223 5331 |
| Деталь: | Harness:AC:IH:Power Supply Unit:EU |
| Парткод: | B223 5338 |
| Деталь: | Power Pack:CB:APO-C/P:-80mic |
| Парткод: | AZ32 0165 |
| Деталь: | Harness:AC:Inlet |
| Парткод: | B223 5333 |
| Деталь: | Harness:Fusing Unit:P1:NA |
| Парткод: | G133 5364 |
| Деталь: | Harness:Fusing Unit:P1:EU |
| Парткод: | G133 5365 |
| Деталь: | Screw:M3 |
| Парткод: | AA14 3576 |
| Деталь: | Bracket:Drawer |
| Парткод: | B223 1069 |
| Деталь: | Gasket:Etnw100-00505:L90 |
| Парткод: | B223 5861 |
| Деталь: | Sound Proofing Material:Duct |
| Парткод: | B223 1329 |
| Деталь: | Fan Motor - Mm60 DC24V |
| Парткод: | B223 1332 |
| Деталь: | Duct:IH:Rear |
| Парткод: | B223 1324 |
| Деталь: | Duct:IH:Front |
| Парткод: | B223 1323 |
| Деталь: | Brushless Motor:Drive:Paper Feed |
| Парткод: | GX06 0015 |
| Деталь: | Bracket:Fusing Drive Sub-unit:Assy |
| Парткод: | B223 1195 |
| Деталь: | Gear:Z27/Z78 |
| Парткод: | AB01 0377 |
| Деталь: | Gearz120 |
| Парткод: | AB01 0375 |
| Деталь: | Gear:Z27 |
| Парткод: | AB01 0376 |
| Деталь: | Cover:Fusing Drive Unit:Lower |
| Парткод: | B223 1362 |
| Деталь: | Ring:Gear:Heat Roller |
| Парткод: | B223 4343 |
| Деталь: | Gear:Z24 |
| Парткод: | AB01 1264 |
| Деталь: | SPRING |
| Парткод: | AA06 6178 |
| Деталь: | Bracket:Drive:Gear |
| Парткод: | B223 4315 |
| Деталь: | Gear:Z16/Z40 |
| Парткод: | AB01 7706 |
| Деталь: | Gear:Z28 |
| Парткод: | AB01 0138 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B223 4318 |
| Деталь: | Stepper Motor:DC24V 24.3W |
| Парткод: | B223 4317 |
| Деталь: | Power Pack:TTS:APO-C/P |
| Парткод: | AZ32 0154 |
| Деталь: | Ozone Filter:No.2:P |
| Парткод: | G133 1296 |
| Деталь: | Duct:Supply:Upper Rear:P1 |
| Парткод: | G133 1343 |
| Деталь: | Duct:Supply:Rear |
| Парткод: | G133 1342 |
| Деталь: | Duct:Supply:Front |
| Парткод: | G133 1341 |
| Деталь: | Tension Spring:Arm:Duplex |
| Парткод: | AA06 1013 |
| Деталь: | Arm:Front |
| Парткод: | B223 4321 |
| Деталь: | Timing Belt:30S2M182 |
| Парткод: | B223 4512 |
| Деталь: | Timing Belt:30S2M234 |
| Парткод: | B223 4536 |
| Деталь: | Timing Belt:30S2M312 |
| Парткод: | B223 4511 |
| Деталь: | Roller Clutch:T24 |
| Парткод: | B223 4529 |
| Деталь: | Pulley:T35/T33 |
| Парткод: | B223 4544 |
| Деталь: | Pulley:T26/T24 |
| Парткод: | B223 4527 |
| Деталь: | Roller Clutch:T26 |
| Парткод: | B223 4535 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Transport Roller:No.1 |
| Парткод: | B223 4513 |
| Деталь: | Transport Roller:No.2 |
| Парткод: | B223 4543 |
| Деталь: | Guide Plate:Left Lower |
| Парткод: | B223 4502 |
| Деталь: | Roller Clutch:T24 |
| Парткод: | B223 4514 |
| Деталь: | Arm:Rear |
| Парткод: | B223 4320 |
| Деталь: | Image Forming Section: Service Papts:2LD:Assy |
| Парткод: | B223 1851 |
| Деталь: | Polygon Mirror Motor Board |
| Парткод: | B180 5445 |
| Деталь: | Harness:Polygon Mirror Motor |
| Парткод: | B223 5241 |
| Деталь: | Harness:Motor:Driver |
| Парткод: | B223 5243 |
| Деталь: | Polygon Mirror Motor |
| Парткод: | AX06 0286 |
| Деталь: | LOUVER |
| Парткод: | B223 1903 |
| Деталь: | Cover - Polygon Motor |
| Парткод: | B223 1882 |
| Деталь: | SCREW |
| Парткод: | B223 1907 |
| Деталь: | SHUTTER ASSY |
| Парткод: | B223 1885 |
| Деталь: | Cover - Upper |
| Парткод: | B223 1881 |
| Деталь: | Link:Shutter:2 |
| Парткод: | B223 1909 |
| Деталь: | Link:Shutter:1 |
| Парткод: | B223 1908 |
| Деталь: | Plate Nut:Link |
| Парткод: | B223 1989 |
| Деталь: | Torsion Spring:Link:2 |
| Парткод: | B223 1914 |
| Деталь: | Torsion Spring:Link:1 |
| Парткод: | B223 1913 |
| Деталь: | PCB Sync Detector |
| Парткод: | B238 5144 |
| Деталь: | Harness:LDB:2LD |
| Парткод: | B223 5235 |
| Деталь: | Harness:Sync Detector |
| Парткод: | B223 5239 |
| Деталь: | Screw:Link:Shutter |
| Парткод: | B223 1988 |
| Деталь: | DRIVE UNIT |
| Парткод: | B223 1125 |
| Деталь: | Duct:Rear:1 |
| Парткод: | B223 1236 |
| Деталь: | Fan Motor:DC24V 2.4W |
| Парткод: | AX64 0179 |
| Деталь: | Duct:Rear:3 |
| Парткод: | B223 1238 |
| Деталь: | Duct:Rear:2 |
| Парткод: | B223 1237 |
| Деталь: | Brushless Motor DC24V8W |
| Парткод: | AX05 0249 |
| Деталь: | Holder:Positioning Sensor |
| Парткод: | B223 1144 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Harness:IOB:Connecting:Drum:Sensor |
| Парткод: | B223 5350 |
| Деталь: | Brushless Motor:DC24V 25W |
| Парткод: | AX06 0308 |
| Деталь: | Snap Ring - M6 |
| Парткод: | AA10 0015 |
| Деталь: | Holder:Magnetic Clutch |
| Парткод: | B223 1370 |
| Деталь: | Magnetic Clutch:0.5n.m |
| Парткод: | AX20 0300 |
| Деталь: | Shaft:Development |
| Парткод: | B223 1148 |
| Деталь: | Gear - 23Z |
| Парткод: | AB01 0367 |
| Деталь: | Magnetic Clutch:0.5n.m |
| Парткод: | AX20 0299 |
| Деталь: | DC Motor 24V |
| Парткод: | B223 1199 |
| Деталь: | Brushless Motor:Drive:Paper Feed |
| Парткод: | GX06 0015 |
| Деталь: | Guide:Harness |
| Парткод: | B223 1364 |
| Деталь: | Gear - 45Z |
| Парткод: | AB01 0368 |
| Деталь: | Sheet:Transport Unit |
| Парткод: | B223 4555 |
| Деталь: | Bracket:Guide Plate |
| Парткод: | B223 4554 |
| Деталь: | Harness:Ground Wire |
| Парткод: | B223 4557 |
| Деталь: | Lever Shaft - Front |
| Парткод: | B223 6322 |
| Деталь: | Lever Shaft - Rear |
| Парткод: | B223 6323 |
| Деталь: | Release Lever |
| Парткод: | B223 6306 |
| Деталь: | Lever Bracket - Middle |
| Парткод: | B223 6320 |
| Деталь: | Driven Roller:Dia16 |
| Парткод: | B223 4559 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B223 4556 |
| Деталь: | Transfer/Separation Unit:P1-U:ASSY |
| Парткод: | G133 6260 |
| Деталь: | TERMINAL |
| Парткод: | B223 6289 |
| Деталь: | Transfer Roller Terminal |
| Парткод: | B223 6285 |
| Деталь: | Sheet:Case:Lower |
| Парткод: | B223 6327 |
| Деталь: | Case:Transfer Roller:Ap-p1 |
| Парткод: | G133 6281 |
| Деталь: | Tension Spring:Driven Roller |
| Парткод: | B223 4553 |
| Деталь: | Bushing:Dia4 |
| Парткод: | B223 4552 |
| Деталь: | Ground Wire - Power Pack |
| Парткод: | B223 6317 |
| Деталь: | Power Pack:D |
| Парткод: | AZ30 0059 |
| Деталь: | Harness - Second Transfer Unit |
| Парткод: | B223 4561 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2145 |
| Деталь: | Torsion Spring:Front |
| Парткод: | B223 4542 |
| Деталь: | Torsion Spring:Rear |
| Парткод: | B223 4541 |
| Деталь: | Guide Plate:Transfer Unit:Holder |
| Парткод: | B223 4551 |
| Деталь: | Drum Stay - Rear |
| Парткод: | B223 6290 |
| Деталь: | Cover - Entrance Sensor |
| Парткод: | B238 4739 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0118 |
| Деталь: | Entrance Sensor Bracket |
| Парткод: | B238 4733 |
| Деталь: | Decal:Warning (High Temperature) |
| Парткод: | B223 4394 |
| Деталь: | Sheet:Harness |
| Парткод: | B223 4558 |
| Деталь: | Spring Cap |
| Парткод: | B223 6319 |
| Деталь: | Transfer Spring |
| Парткод: | B223 6308 |
| Деталь: | Spring Anchor |
| Парткод: | B223 6321 |
| Деталь: | Guide Pin:Holder |
| Парткод: | B223 4545 |
| Деталь: | Decal:Replacement Indication |
| Парткод: | B223 6324 |
| Деталь: | Supporter - Left No.2 |
| Парткод: | B223 2710 |
| Деталь: | Supporter - Left No.1 |
| Парткод: | B223 2705 |
| Деталь: | Rubber Foot Cover |
| Парткод: | B238 1066 |
| Деталь: | Heat Sink:Heater:NA |
| Парткод: | B223 2702 |
| Деталь: | Heat Sink:Heater:EU |
| Парткод: | B223 2703 |
| Деталь: | Cover:Connector:Heater |
| Парткод: | B223 1207 |
| Деталь: | Bracket:Paper Feed Unit |
| Парткод: | B223 1120 |
| Деталь: | Positioning Cap - Short |
| Парткод: | B223 2714 |
| Деталь: | Supporter - Right |
| Парткод: | B223 2715 |
| Деталь: | CUSHION |
| Парткод: | AA16 1163 |
| Деталь: | Rubber Foot:H5 |
| Парткод: | B101 1097 |
| Деталь: | Side Fence:Front |
| Парткод: | B223 2698 |
| Деталь: | Side Fence:Rear |
| Парткод: | B223 2697 |
| Деталь: | Grip:Side Fence |
| Парткод: | B223 2667 |
| Деталь: | Spring Plate:Stopper |
| Парткод: | B223 2668 |
| Деталь: | Decal:Side Fence |
| Парткод: | B223 2645 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | B223 2655 |
| Деталь: | Cover:Manual Feed |
| Парткод: | B223 2661 |
| Деталь: | Decal:Scale |
| Парткод: | B223 2644 |
| Деталь: | Harness:Paper Size Sensor |
| Парткод: | B223 2669 |
| Деталь: | Paper size sensor |
| Парткод: | AW50 0031 |
| Деталь: | Rack:Manual Feed |
| Парткод: | B223 2631 |
| Деталь: | Gear:16z |
| Парткод: | B223 2666 |
| Деталь: | EXTENSION TRAY |
| Парткод: | B223 2663 |
| Деталь: | MANUAL FEED TABLE |
| Парткод: | B223 2662 |
| Деталь: | Gear:18Z |
| Парткод: | B223 4459 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Timing Belt:30S2M216 |
| Парткод: | AA04 3969 |
| Деталь: | Gear:Pulley:Z18/T23 |
| Парткод: | B223 4458 |
| Деталь: | Spacer:Idler |
| Парткод: | B223 4456 |
| Деталь: | Timing Pulley:23T |
| Парткод: | B223 4464 |
| Деталь: | SCREW |
| Парткод: | B238 4483 |
| Деталь: | Inner Cover:Exit:Front |
| Парткод: | B223 4437 |
| Деталь: | Inner Cover:Exit:Rear |
| Парткод: | B223 4438 |
| Деталь: | Harness:IOB:Paper Exit Unit:C |
| Парткод: | B223 4439 |
| Деталь: | Bracket:Sensor |
| Парткод: | B223 4426 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Transport Roller:Dia18 |
| Парткод: | B223 4454 |
| Деталь: | Guide Plate:Upper Right |
| Парткод: | B223 4461 |
| Деталь: | BUSHING - M4 |
| Парткод: | H053 2208 |
| Деталь: | Tension Spring:1.3n |
| Парткод: | B223 4452 |
| Деталь: | Bracket:Gear:Coupling |
| Парткод: | B223 4447 |
| Деталь: | Gear:Z14/Z40 |
| Парткод: | B223 4451 |
| Деталь: | Gear:Z20/Z32 |
| Парткод: | B223 4467 |
| Деталь: | Bracket:Stepper Motor:Gate |
| Парткод: | B223 4444 |
| Деталь: | Stepper Motor:DC24V 70.2W |
| Парткод: | B223 4441 |
| Деталь: | STOPPER |
| Парткод: | B223 4468 |
| Деталь: | Gear:Z14 |
| Парткод: | B223 4450 |
| Деталь: | PCU:M |
| Парткод: | G133 2021 |
| Деталь: | PCU:C |
| Парткод: | G133 2022 |
| Деталь: | PCU:Y |
| Парткод: | G133 2023 |
| Деталь: | Transfer/separation Unit:P1:Assy |
| Парткод: | G133 6260 |
| Деталь: | Cover:Left:Middle:Filter:Assy |
| Парткод: | G133 1280 |
| Деталь: | Decal - Paper Size |
| Парткод: | B238 2524 |
| Деталь: | Safety Sheet |
| Парткод: | A232 8561 |
| Деталь: | Sheet:Collar_Chart:JPN:AP-P1B |
| Парткод: | G146 7491 |
| Деталь: | Manual:Saftyinfo |
| Парткод: | G133 8601 |
| Деталь: | Manual:Saftyinfo:AP-P1 |
| Парткод: | G133 8603 |
| Деталь: | Manual:Quick:NA |
| Парткод: | G133 8605 |
| Деталь: | Manual:Notes_Admin |
| Парткод: | G133 8680 |
| Деталь: | Screw:M3 |
| Парткод: | AA14 3520 |
| Деталь: | SPRING:PRESSURE:PICKUP |
| Парткод: | AA06 3568 |
| Деталь: | Bracket:Safety Switch |
| Парткод: | B223 5813 |
| Деталь: | Bracket:Lever:Safety Switch |
| Парткод: | B223 5814 |
| Деталь: | DC Motor:Shutter:Unit:DC24V 3.6W |
| Парткод: | B223 1213 |
| Деталь: | DC Motor Bracket |
| Парткод: | B223 1212 |
| Деталь: | TORSION SPRING |
| Парткод: | B223 1224 |
| Деталь: | Shutter Link |
| Парткод: | B223 1225 |
| Деталь: | Sensor Link Bracket |
| Парткод: | B223 1221 |
| Деталь: | Harness:IOB:Connecting:TM/P:Sensor |
| Парткод: | B223 5309 |
| Деталь: | Density Sensor:Assy |
| Парткод: | B223 5876 |
| Деталь: | Tension Spring:Shutter:Sensor:TM |
| Парткод: | AA06 0151 |
| Деталь: | Hook:Solenoid:Sensor:TM |
| Парткод: | B238 5867 |
| Деталь: | Dc Solenoid:Shutter:Density Sensor:AssY |
| Парткод: | B238 5875 |
| Деталь: | DENSITY SENSOR |
| Парткод: | B223 6395 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Harness:IOB:LD Unit:Shutter |
| Парткод: | B223 5313 |
| Деталь: | Sensor Shutter Bracket |
| Парткод: | B223 1227 |
| Деталь: | Panel:Interface:SECC |
| Парткод: | B154 5869 |
| Деталь: | Supporter:Lower |
| Парткод: | G133 5822 |
| Деталь: | Grip:Rack:Left Lower |
| Парткод: | B223 5823 |
| Деталь: | Cover:Sd-card:P1:Lower |
| Парткод: | G133 5863 |
| Деталь: | Gasket:EGUN1-0105:L240 |
| Парткод: | B223 5862 |
| Деталь: | Knob Screw:M3 |
| Парткод: | G104 5141 |
| Деталь: | Rail:Right |
| Парткод: | G133 5795 |
| Деталь: | Rail:Left |
| Парткод: | G133 5796 |
| Деталь: | Rack:Auxiliary:Left Lower:P1d |
| Парткод: | G133 5821 |
| Деталь: | PCB:Type-JBX4 |
| Парткод: | G133 5701 |
| Деталь: | Ram:Fm25l256-pg(rev.ag) |
| Парткод: | 14 076 465 |
| Деталь: | PCB:SDRAM-DIMM:256Mb:CHN:Assy |
| Парткод: | G332 5730 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3499 |
| Деталь: | Bushing:HDD |
| Парткод: | AA16 1162 |
| Деталь: | Spring Plate:Screw:HDD |
| Парткод: | B223 5877 |
| Деталь: | Bracket:Insulator:HDD:Upper |
| Парткод: | B223 5825 |
| Деталь: | Bracket:Insulator:HDD |
| Парткод: | B223 5826 |
| Деталь: | HDD:Hitachi:40gb:Path-kai:Rohs |
| Парткод: | B179 5995 |
| Деталь: | Harness:HDD |
| Парткод: | G874 5801 |
| Деталь: | Harness:HDD:Power Source:Apd |
| Парткод: | G133 5797 |
| Деталь: | SD-Card |
| Парткод: | G133 5740 |
| Деталь: | Fan Motor - Mm42x10.5 DC5V |
| Парткод: | B237 5721 |
| Деталь: | Bracket:Fan:Control Board:P1 |
| Парткод: | G133 5827 |
| Деталь: | Cover:SD-Card:P1:Upper |
| Парткод: | G133 5862 |
| Деталь: | Harness:IOB:Main:Upper |
| Парткод: | B223 5302 |
| Деталь: | Harness:IOB:Main:Lower |
| Парткод: | B222 5300 |
| Деталь: | PCB:IOB:AP-C1/P1 |
| Парткод: | B223 5120 |
| Деталь: | Harness:IOB:Main:Middle |
| Парткод: | B223 5301 |
| Деталь: | Plate:Rack:Auxiliary:Right |
| Парткод: | B223 5816 |
| Деталь: | Inner Cover:Upper:Left |
| Парткод: | B223 1241 |
| Деталь: | Inner Cover:Upper:Left:EU |
| Парткод: | B222 1241 |
| Деталь: | Decal:Colored Display:BK:Inner Cover |
| Парткод: | B238 3364 |
| Деталь: | Decal:Colored Display:Y:Inner Cover |
| Парткод: | B238 3365 |
| Деталь: | Decal:Colored Display:C:Inner Cover |
| Парткод: | B238 3366 |
| Деталь: | Decal:Colored Display:M:Inner Cover |
| Парткод: | B238 3367 |
| Деталь: | Inner Cover - Middle |
| Парткод: | B223 1244 |
| Деталь: | Decal - Cleaning |
| Парткод: | B238 1368 |
| Деталь: | Decal - Shielding Plate Y |
| Парткод: | GA00 3030 |
| Деталь: | Decal - Shielding Plate C |
| Парткод: | GA00 3032 |
| Деталь: | Decal - Shielding Plate M |
| Парткод: | GA00 3031 |
| Деталь: | Decal - Shielding Plate K |
| Парткод: | GA00 3033 |
| Деталь: | Decal:Drum Stay:Lever |
| Парткод: | G133 1311 |
| Деталь: | Decal - Misfeed Removal B1 |
| Парткод: | B238 1362 |
| Деталь: | Drum Stay:PCU |
| Парткод: | G133 1300 |
| Деталь: | Lever:Drum Stay:PCU |
| Парткод: | G133 1303 |
| Деталь: | SPRING |
| Парткод: | B223 1318 |
| Деталь: | Drum Stay |
| Парткод: | B223 1306 |
| Деталь: | WIRE |
| Парткод: | B223 1319 |
| Деталь: | Ball Bearing Plate |
| Парткод: | B223 1315 |
| Деталь: | Ball Bearing Clip |
| Парткод: | B223 1316 |
| Деталь: | Screw:Lever:Drum Stay |
| Парткод: | B223 1317 |
| Деталь: | Stopper:Magnet Catch |
| Парткод: | B223 1249 |
| Деталь: | Hinge - Cover Drum Stay |
| Парткод: | B223 1123 |
| Деталь: | Case - Remove Paper Dust |
| Парткод: | B238 2615 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 1012 |
| Деталь: | Inner Cover:Upper:Right |
| Парткод: | B223 1243 |
| Деталь: | Cover:Right:Front |
| Парткод: | B223 1271 |
| Деталь: | Cover:Right:Front:EU |
| Парткод: | B222 1271 |
| Деталь: | Decal:Intermediate Transfer:Release |
| Парткод: | G133 1244 |
| Деталь: | Decal:Intermediate Transfer:Lock |
| Парткод: | G133 1245 |
| Деталь: | Cover:Left:Middle:P |
| Парткод: | G133 1283 |
| Деталь: | Cover:Left:Middle:Filter:Assy |
| Парткод: | G133 1280 |
| Деталь: | Cover:Left |
| Парткод: | B223 1281 |
| Деталь: | Cover:Left:Eu |
| Парткод: | B222 1281 |
| Деталь: | Decal:Cover:Left:Guide Plate |
| Парткод: | G133 1285 |
| Деталь: | Decal:Set:Fusing Unit |
| Парткод: | B223 4392 |
| Деталь: | Cover:Rear |
| Парткод: | B223 1291 |
| Деталь: | Cover:Rear:EU |
| Парткод: | B222 1291 |
| Деталь: | Decal:PDF Direct |
| Парткод: | GA00 3144 |
| Деталь: | Decal:PS3:Clear |
| Парткод: | GA00 3175 |
| Деталь: | Ozone Filter:No.1 |
| Парткод: | G133 1295 |
| Деталь: | Cap:Cover:Rear |
| Парткод: | B223 1293 |
| Деталь: | Emblem Cover |
| Парткод: | B223 1253 |
| Деталь: | Sheet:EMBLEM:RIC |
| Парткод: | G133 8331 |
| Деталь: | Sheet:EMBLEM:SVN |
| Парткод: | G133 8332 |
| Деталь: | Sheet:EMBLEM:GES:NA |
| Парткод: | G133 8333 |
| Деталь: | Sheet:EMBLEM:LAN:NA |
| Парткод: | G133 8334 |
| Деталь: | Sheet:EMBLEM:INF |
| Парткод: | G133 8335 |
| Деталь: | Sheet:EMBLEM:NSA |
| Парткод: | G133 8336 |
| Деталь: | Sheet:EMBLEM:REX |
| Парткод: | G133 8337 |
| Деталь: | Sheet:Emblem:GES |
| Парткод: | G133 8338 |
| Деталь: | Sheet:EMBLEM:LAN:EU |
| Парткод: | G133 8339 |
| Деталь: | Hinge - Front Cover |
| Парткод: | G020 1332 |
| Деталь: | TAPPING SCREW |
| Парткод: | AA14 3823 |
| Деталь: | Cover:Front:EU |
| Парткод: | B224 1251 |
| Деталь: | Cover:Right Rear:Fan |
| Парткод: | B223 1274 |
| Деталь: | MAGNET CATCH |
| Парткод: | B024 1264 |
| Деталь: | Sheet:Misfeed Removal:P1 |
| Парткод: | G133 1256 |
| Деталь: | Cleaner:Shield Glass:Assy |
| Парткод: | B223 1279 |
| Деталь: | Filter:Right Rear |
| Парткод: | B223 1276 |
| Деталь: | Cover:Right:Rear |
| Парткод: | B223 1272 |
| Деталь: | PAPER FEED UNIT |
| Парткод: | B223 2750 |
| Деталь: | Paper End Feeler |
| Парткод: | B223 2767 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Harness - Paper Fee Unit |
| Парткод: | B223 2773 |
| Деталь: | Sensor bracket |
| Парткод: | B223 2778 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0128 |
| Деталь: | Bracket:Sensor |
| Парткод: | B082 2781 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0122 |
| Деталь: | DC Solenoid 24V |
| Парткод: | B223 2780 |
| Деталь: | STAY |
| Парткод: | B223 2776 |
| Деталь: | Transport Roller |
| Парткод: | B238 2569 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2143 |
| Деталь: | Harness Sheet |
| Парткод: | B223 2772 |
| Деталь: | Ground Plate - Front |
| Парткод: | B223 2786 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF03 0090 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1252 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | Feed guide |
| Парткод: | B223 2829 |
| Деталь: | Paper Feed Roller:Feed |
| Парткод: | AF03 1090 |
| Деталь: | Gear - Roller Clutch |
| Парткод: | AB01 1218 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Ground Plate - Feed |
| Парткод: | B223 2765 |
| Деталь: | Pickup Arm |
| Парткод: | B223 2761 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0691 |
| Деталь: | Lever - Feed |
| Парткод: | G065 2767 |
| Деталь: | Gear-24z |
| Парткод: | B223 2764 |
| Деталь: | Feed Shaft |
| Парткод: | B223 2762 |
| Деталь: | Paper Feed Roller:Separate |
| Парткод: | AF03 2090 |
| Деталь: | TORQUE LIMITER |
| Парткод: | B004 2783 |
| Деталь: | Separate Driven Shaft |
| Парткод: | B223 2810 |
| Деталь: | Gear:Separate:Driven |
| Парткод: | AB01 0157 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0693 |
| Деталь: | PRESSURE LEVER |
| Парткод: | G065 2774 |
| Деталь: | Gear:Separate:Drive |
| Парткод: | AB01 0156 |
| Деталь: | Separate Drive Shaft |
| Парткод: | B223 2815 |
| Деталь: | Gear - 22Z |
| Парткод: | B223 2819 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Release Lever |
| Парткод: | G065 2776 |
| Деталь: | LINK LEVER |
| Парткод: | G065 2775 |
| Деталь: | Spring - Release |
| Парткод: | AA06 2259 |
| Деталь: | Screw:A |
| Парткод: | AA14 3807 |
| Деталь: | Guide Plate:Upper:Gate |
| Парткод: | B223 4483 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Bracket:Sensor:Entrance |
| Парткод: | B223 4566 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Driven Roller:Dia16 |
| Парткод: | B223 4559 |
| Деталь: | Tension Spring:Driven Roller |
| Парткод: | B223 4560 |
| Деталь: | Bushing:Dia4 |
| Парткод: | B223 4552 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Reverse Roller:Feed Paper Again |
| Парткод: | B223 4537 |
| Деталь: | Reverse Roller Gear |
| Парткод: | AB01 4161 |
| Деталь: | Tightener |
| Парткод: | B223 4562 |
| Деталь: | SHOULDER SCREW |
| Парткод: | B044 1847 |
| Деталь: | Spring:Tightener |
| Парткод: | B223 4564 |
| Деталь: | Timing Belt:30S2M268 |
| Парткод: | B223 4526 |
| Деталь: | Pulley:T30 |
| Парткод: | B223 4586 |
| Деталь: | Stepper Motor:DC4.29V 1.7W |
| Парткод: | B223 4572 |
| Деталь: | Rubber Bushing - 6 45hs |
| Парткод: | AA10 1021 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B223 4575 |
| Деталь: | Gear:Pulley:Z24/T40 |
| Парткод: | B223 4571 |
| Деталь: | Timing Belt:30S2M128 |
| Парткод: | B223 4573 |
| Деталь: | COLLAR |
| Парткод: | B044 1825 |
| Деталь: | Guide Plate:Right |
| Парткод: | B223 4501 |
| Деталь: | Stopper Screw - M3 |
| Парткод: | 58 403 022 |
| Деталь: | Fan Motor - DC24V |
| Парткод: | GX64 0020 |
| Деталь: | Duct:Fusing |
| Парткод: | B223 1326 |
| Деталь: | Duct:Fusing:Rear |
| Парткод: | B223 1327 |
| Деталь: | Harness:IOB:Connecting:IH |
| Парткод: | B223 5305 |
| Деталь: | Invertor:IH:EU |
| Парткод: | B223 5172 |
| Деталь: | Invertor:IH |
| Парткод: | B223 5170 |
| Деталь: | Guide:Gear |
| Парткод: | B223 2694 |
| Деталь: | Timing Belt:40S2M144 |
| Парткод: | B700 2649 |
| Деталь: | Gear Pulley |
| Парткод: | AB01 7493 |
| Деталь: | COLLAR |
| Парткод: | B044 1825 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B223 2691 |
| Деталь: | Rubber Bushing - 6 45hs |
| Парткод: | AA10 1021 |
| Деталь: | Stepper Motor:DC24V 26.4W |
| Парткод: | B223 2685 |
| Деталь: | SHAFT |
| Парткод: | B238 1225 |
| Деталь: | CAM |
| Парткод: | B238 1226 |
| Деталь: | HOLDER |
| Парткод: | B238 1223 |
| Деталь: | DC Motor 24V |
| Парткод: | B223 1199 |
| Деталь: | Fan Motor - Mm60 DC24V |
| Парткод: | B223 1332 |
| Деталь: | Bracket:Fan:Power Source:IH |
| Парткод: | B223 5844 |
| Деталь: | Hinge:Application:Rack |
| Парткод: | B223 5841 |
| Деталь: | Bracket:Rack:Application |
| Парткод: | B223 5843 |
| Деталь: | Ground Wire:Rack:Right Lower:HF |
| Парткод: | B223 5866 |
| Деталь: | Inner Cover:Duplex |
| Парткод: | B223 4534 |
| Деталь: | Inner Cover:Duplex:Rear |
| Парткод: | B223 4533 |
| Деталь: | Grip:Open And Close:Duplex Unit |
| Парткод: | B223 4579 |
| Деталь: | Hook:Stopper:Duplex Unit:Assy |
| Парткод: | B223 4599 |
| Деталь: | Tension Spring:Hook:Stopper |
| Парткод: | B223 4532 |
| Деталь: | Inner Cover:Sensor |
| Парткод: | B223 4482 |
| Деталь: | Tension Spring:Wire:180n |
| Парткод: | B223 4525 |
| Деталь: | Driven Roller:Dia16 |
| Парткод: | B223 4559 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B223 4538 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Guide Plate:Cover |
| Парткод: | B223 4531 |
| Деталь: | Cover:Duplex |
| Парткод: | B223 4540 |
| Деталь: | Spring:Cover:Manual Feed |
| Парткод: | B223 2665 |
| Деталь: | Cover:Manual Feed:Entrance |
| Парткод: | B223 2664 |
| Деталь: | Sheet:Cover:Duplex |
| Парткод: | B223 4539 |
| Деталь: | Drawer:Intermediate Transfer:Assy |
| Парткод: | B223 6140 |
| Деталь: | Harness:IOB:Toner Supply:CL |
| Парткод: | B223 5304 |
| Деталь: | Harness:P.p:High Voltage Line:T/TS |
| Парткод: | B223 5310 |
| Деталь: | Toner End Sensor |
| Парткод: | AW02 0185 |
| Деталь: | Pump Unit - BK |
| Парткод: | B223 3211 |
| Деталь: | Pump Unit - M |
| Парткод: | B223 3204 |
| Деталь: | Pump Unit - C |
| Парткод: | B223 3203 |
| Деталь: | Pump Unit - Y |
| Парткод: | B223 3202 |
| Деталь: | TUBE CLAMP |
| Парткод: | B223 3206 |
| Деталь: | Nozzle Assy |
| Парткод: | B223 3205 |
| Деталь: | Tube Clip |
| Парткод: | B223 3209 |
| Деталь: | Gate Pawl:Upper |
| Парткод: | B223 4495 |
| Деталь: | Gate Pawl:Entrance |
| Парткод: | B223 4475 |
| Деталь: | Gear:21Z |
| Парткод: | B223 4472 |
| Деталь: | Tension Spring:Lever |
| Парткод: | B223 4584 |
| Деталь: | DC Solenoid:Duplex |
| Парткод: | B223 4581 |
| Деталь: | Lever:Gate Pawl:Upper |
| Парткод: | B223 4477 |
| Деталь: | Decal:Open And Close |
| Парткод: | B223 4492 |
| Деталь: | Stopper:Gate Pawl:Upper |
| Парткод: | B223 4478 |
| Деталь: | Tension Spring:Gate Pawl:1.6n |
| Парткод: | B223 4479 |
| Деталь: | Tension Spring:10n |
| Парткод: | B223 4485 |
| Деталь: | Driven Roller:Dia16 |
| Парткод: | B223 4474 |
| Деталь: | BUSHING - M4 |
| Парткод: | G060 4435 |
| Деталь: | Compression Spring:Driven Roller |
| Парткод: | B223 4484 |
| Деталь: | Guide Plate:Open And Close |
| Парткод: | B223 4471 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Bracket:Paper Exit Unit:Rear |
| Парткод: | B223 4481 |
| Деталь: | Gate Pawl:Duplex |
| Парткод: | B223 4578 |
| Деталь: | Tension Spring:Gate Pawl:0.5n |
| Парткод: | B223 4589 |
| Деталь: | Guide Plate:Left Upper |
| Парткод: | B223 4503 |
| Деталь: | Gear:Sensor:Turn |
| Парткод: | AB01 0088 |
| Деталь: | Roller:Ferrite Core:Assy |
| Парткод: | B223 4235 |
| Деталь: | Fusing Belt:Dia60:Adhesion |
| Парткод: | B223 4221 |
| Деталь: | Bushing:Heat Roller |
| Парткод: | AE03 1046 |
| Деталь: | Ball Bearing:Dia12xdia21x7 |
| Парткод: | AE03 0069 |
| Деталь: | Hot Roller:Dia35 |
| Парткод: | AE01 0059 |
| Деталь: | Ball Bearing:Dia17xdia26x5 |
| Парткод: | AE03 0071 |
| Деталь: | Pressure Roller:Dia40 |
| Парткод: | AE02 0115 |
| Деталь: | Roller:Belt Tensioner:Dia12 |
| Парткод: | B223 4226 |
| Деталь: | Gear:Hot Roller |
| Парткод: | AB01 2044 |
| Деталь: | Spacer:Heat Roller |
| Парткод: | B223 4233 |
| Деталь: | Gear:Turn:Ferrite Core:Z16 |
| Парткод: | AB01 1249 |
| Деталь: | Gear:Pressuer Roller |
| Парткод: | AB01 2045 |
| Деталь: | Gear:Drive:Fusing |
| Парткод: | AB01 7703 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | AA14 3526 |
| Деталь: | Bushing:Fusing Sub-unit |
| Парткод: | AE03 1065 |
| Деталь: | Compression Spring:Belt Tensioner |
| Парткод: | AA06 3954 |
| Деталь: | Gear:Idler:Pressure Roller |
| Парткод: | AB01 2051 |
| Деталь: | Rear Bushing - Oil Supply Roller |
| Парткод: | AE03 1062 |
| Деталь: | Bracket:Oil Supply Roller |
| Парткод: | B223 4181 |
| Деталь: | Compression Spring:Oil Supply Roller |
| Парткод: | AA06 3953 |
| Деталь: | Cleaning Roller - Oil Supply Roller |
| Парткод: | AE04 0066 |
| Деталь: | Oil Supply Roller |
| Парткод: | AE04 0069 |
| Деталь: | Front Bushing - Oil Supply Roller |
| Парткод: | AE03 1061 |
| Деталь: | Encoder:Ferrite Core:Change |
| Парткод: | B223 4240 |
| Деталь: | Gear:Turn:Sensor |
| Парткод: | AB01 0118 |
| Деталь: | Screw:Positioning Control |
| Парткод: | B223 4072 |
| Деталь: | Heater:120V:500W |
| Парткод: | AX43 0156 |
| Деталь: | Heater:230V:500W |
| Парткод: | AX43 0157 |
| Деталь: | Thermistor:Fusing:Assy |
| Парткод: | B223 4172 |
| Деталь: | Thermistor:Pressure:Assy |
| Парткод: | B223 4177 |
| Деталь: | Thermostat:Assy |
| Парткод: | B223 4162 |
| Деталь: | Positioning Guide - Front |
| Парткод: | B223 6311 |
| Деталь: | Positioning Guide - Rear |
| Парткод: | B223 6312 |
| Деталь: | CUSHION |
| Парткод: | B223 6315 |
| Деталь: | TENSION SPRING |
| Парткод: | B238 2676 |
| Деталь: | Registration Roller Bushing |
| Парткод: | B238 2675 |
| Деталь: | Registration Roller - Driven |
| Парткод: | B238 2661 |
| Деталь: | Gear - 18Z |
| Парткод: | B238 2657 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Registration Roller Knob |
| Парткод: | B223 2558 |
| Деталь: | Registration Roller - Drive |
| Парткод: | B238 2652 |
| Деталь: | Gear - 16Z |
| Парткод: | B238 2655 |
| Деталь: | Gear - 30Z |
| Парткод: | B238 2656 |
| Деталь: | Cleaner Bracket |
| Парткод: | B238 2670 |
| Деталь: | Cover - Remove Paper Dust |
| Парткод: | B238 2622 |
| Деталь: | STAY |
| Парткод: | B238 2621 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Harness:Registration Sensor |
| Парткод: | B223 2599 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3404 |
| Деталь: | Link:Stopper |
| Парткод: | B223 4523 |
| Деталь: | Guide Plate:Registration:Right |
| Парткод: | B223 2570 |
| Деталь: | Registration Guide Plate - Left |
| Парткод: | B238 2612 |
| Деталь: | Wire:Stopper:Dia1.5 |
| Парткод: | B223 4524 |
| Деталь: | GUIDE PLATE |
| Парткод: | B223 2835 |
| Деталь: | Guide Plate No.2 |
| Парткод: | B223 2840 |
| Деталь: | Bracket:Cover:Harness |
| Парткод: | B223 2846 |
| Деталь: | Cover:Harness |
| Парткод: | B223 2848 |
| Деталь: | Drive Unit:Toner Supply |
| Парткод: | G133 3405 |
| Деталь: | PCB:RFID:RW |
| Парткод: | B238 5051 |
| Деталь: | Rfid Ground Plate |
| Парткод: | B223 3470 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Shaft:Drive:Drive Unit:CM |
| Парткод: | B223 3426 |
| Деталь: | Shaft:Drive:Drive Unit:BKY |
| Парткод: | B223 3424 |
| Деталь: | Timing Belt:Toner Bottle |
| Парткод: | B223 3441 |
| Деталь: | Pulley:Toner Bottle:YC |
| Парткод: | B223 3461 |
| Деталь: | Pulley:Toner Bottle:CM |
| Парткод: | B223 3462 |
| Деталь: | Gear:Toner Bottle:DRIVE |
| Парткод: | B223 3463 |
| Деталь: | Magnetic Clutch - 0.25n.m |
| Парткод: | B223 3457 |
| Деталь: | Magnetic Clutch - 0.25n.m B |
| Парткод: | B223 3455 |
| Деталь: | Spring:Drive Unit:Toner Bottle |
| Парткод: | B223 3428 |
| Деталь: | Gear:Magnetic Clutch:Y |
| Парткод: | B223 3464 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | B223 6464 |
| Деталь: | Transport Screw Bracket |
| Парткод: | B223 6471 |
| Деталь: | Bushing - 5x 10x2.5 |
| Парткод: | B223 6475 |
| Деталь: | Gear - 21Z |
| Парткод: | B223 6472 |
| Деталь: | Bushing - Dia5 |
| Парткод: | B223 6476 |
| Деталь: | Transport Screw Shaft |
| Парткод: | B223 6473 |
| Деталь: | GEAR - 29Z |
| Парткод: | B223 6474 |
| Деталь: | Gear - 20Z |
| Парткод: | B223 6463 |
| Деталь: | Pipe:Front |
| Парткод: | G133 6451 |
| Деталь: | Separation Plate - Upper Left |
| Парткод: | B223 1087 |
| Деталь: | Separation Plate - Upper MIiddle Left |
| Парткод: | B223 1084 |
| Деталь: | Separation Plate - Upper MIiddle Right |
| Парткод: | B223 1080 |
| Деталь: | Separation Plate - Upper Right |
| Парткод: | B223 1076 |
| Деталь: | Lever Bracket |
| Парткод: | B223 6467 |
| Деталь: | Bracket:Hinge:Left |
| Парткод: | B223 1103 |
| Деталь: | Bracket:Grip:Right Front |
| Парткод: | B223 1102 |
| Деталь: | Imaging Unit Plate - Outer |
| Парткод: | B223 1899 |
| Деталь: | Imaging Unit Plate - Inner |
| Парткод: | B223 1898 |
| Деталь: | Imaging Unit Plate - Front |
| Парткод: | B223 1896 |
| Деталь: | Imaging Unit Plate - Rear |
| Парткод: | B223 1897 |
| Деталь: | Cap:Grip |
| Парткод: | B223 1245 |
| Деталь: | Grip:Front |
| Парткод: | B223 1101 |
| Деталь: | Used Toner Sensor Bracket |
| Парткод: | B223 6502 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Used Toner Sensor Feeler |
| Парткод: | B223 6503 |
| Деталь: | Harness - Used Toner Sensor |
| Парткод: | B238 5313 |
| Деталь: | Bracket:Fan |
| Парткод: | B223 1331 |
| Деталь: | Fan Motor - Mm60 DC24V |
| Парткод: | B223 1332 |
| Деталь: | Harness:IOB:Fan Motor |
| Парткод: | B223 5311 |
| Деталь: | Rail:Collection Bottle |
| Парткод: | G133 6496 |
| Деталь: | Bracket:Handle:Main Switch:Peen |
| Парткод: | B238 5821 |
| Деталь: | Cover:Slide Switch |
| Парткод: | B238 5824 |
| Деталь: | Link:Power Source:Switch |
| Парткод: | B238 5825 |
| Деталь: | Cleaning Unit Rail |
| Парткод: | B223 6198 |
| Деталь: | Fan Motor:DC24V 2.4W |
| Парткод: | AX64 0179 |
| Деталь: | Duct:Exit |
| Парткод: | G133 1336 |
| Деталь: | Holder:Coil:Front Lower |
| Парткод: | B223 4311 |
| Деталь: | Holder:Coil:Rear Lower |
| Парткод: | B223 4312 |
| Деталь: | Stay:IH:Holder |
| Парткод: | B223 4310 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | 54 472 768 |
| Деталь: | Bracket:Fan:Ih |
| Парткод: | B223 1328 |
| Деталь: | Sirocco Fan:DC24V 2.6W |
| Парткод: | AX65 0045 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Bracket:Sensor:Machine Or Copier |
| Парткод: | B223 4329 |
| Деталь: | Bracket:Pin |
| Парткод: | B223 4337 |
| Деталь: | Bracket:Sensor:Turn |
| Парткод: | B223 4328 |
| Деталь: | Bracket:Pressure:Coil |
| Парткод: | B223 4308 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3438 |
| Деталь: | Guide:IH:Upper |
| Парткод: | B223 4307 |
| Деталь: | Compression Spring:Lever |
| Парткод: | AA06 3439 |
| Деталь: | Lever:Lock:Fusing Unit |
| Парткод: | B223 4327 |
| Деталь: | Supporter:Fusing Unit |
| Парткод: | B223 4336 |
| Деталь: | Frame:Coil:Front |
| Парткод: | B223 4301 |
| Деталь: | Frame:Coil:Rear |
| Парткод: | B223 4303 |
| Деталь: | IH Coilunit:EU |
| Парткод: | B223 4011 |
| Деталь: | IH Coil Unit |
| Парткод: | B223 4349 |
| Деталь: | Holder:Fusing Unit:Assy |
| Парткод: | B223 4360 |
| Деталь: | Guide:Fusing Unit |
| Парткод: | B223 4341 |
| Деталь: | Decal:Warning (High Temperature) |
| Парткод: | B223 4397 |
| Деталь: | Decal:Warning (high Temperature):IH |
| Парткод: | B223 4393 |
| Деталь: | Sheet - Transport Sub-unit |
| Парткод: | B223 2677 |
| Деталь: | Guide Plate - Vertical Transport |
| Парткод: | B223 2675 |
| Деталь: | BUSHING - M4 |
| Парткод: | G060 2652 |
| Деталь: | Spring - 11n |
| Парткод: | B223 2676 |
| Деталь: | Vertical Transport Roller |
| Парткод: | AF02 0646 |
| Деталь: | Guide Plate:Transport Unit:Exit |
| Парткод: | B223 2648 |
| Деталь: | Spring:Pressure:5n |
| Парткод: | B223 2649 |
| Деталь: | Roller:Driven:Dia16 |
| Парткод: | B223 2641 |
| Деталь: | Spacer:Wire:Stopper |
| Парткод: | B223 4522 |
| Деталь: | Harness:Duplex Md |
| Парткод: | B223 4587 |
| Деталь: | Shaft:Pulley:Wire |
| Парткод: | B223 4594 |
| Деталь: | Pulley:DIA13 |
| Парткод: | B223 4595 |
| Деталь: | Bracket:Shaft:Pulley:Wire |
| Парткод: | B223 4596 |
| Деталь: | Paper Tray:No.1:Assy |
| Парткод: | B223 2851 |
| Деталь: | Screw:DIA6 |
| Парткод: | AA14 3843 |
| Деталь: | Slide Rail - Left |
| Парткод: | B223 2890 |
| Деталь: | Slide Rail Stopper - Left |
| Парткод: | B223 2894 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B223 2940 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3006 |
| Деталь: | Decal - Paper Set Direction No.1 |
| Парткод: | B237 2521 |
| Деталь: | Cover - Paper Tray No.1 |
| Парткод: | B223 2857 |
| Деталь: | Paper Tray Grip |
| Парткод: | B223 2860 |
| Деталь: | Decal - Grip |
| Парткод: | B238 2526 |
| Деталь: | Lever - Release Inner |
| Парткод: | B223 2862 |
| Деталь: | Tension Spring:Grip |
| Парткод: | AA06 1014 |
| Деталь: | Release Shaft |
| Парткод: | B223 2863 |
| Деталь: | Grip Holder |
| Парткод: | B223 2861 |
| Деталь: | Screw:Tp:M4 |
| Парткод: | AA14 3577 |
| Деталь: | LEVER:RELEASE:PAPER TRAY:OUTER |
| Парткод: | B223 2868 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | END FENCE |
| Парткод: | B223 2912 |
| Деталь: | Side Fence - Front |
| Парткод: | B223 2870 |
| Деталь: | Stopper Lever - Front |
| Парткод: | B223 2923 |
| Деталь: | Spring Plate - Release Lever |
| Парткод: | B004 2923 |
| Деталь: | Plate - Side Fence Right |
| Парткод: | B223 2935 |
| Деталь: | Plate - Side Fence |
| Парткод: | B223 2934 |
| Деталь: | Gear - 16Z |
| Парткод: | B223 2936 |
| Деталь: | Rise No.1 Shaft |
| Парткод: | B223 2865 |
| Деталь: | Rise Lever |
| Парткод: | B223 2918 |
| Деталь: | Side Fence - Rear |
| Парткод: | B223 2880 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A267 2860 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Decal - Side Fence Rear |
| Парткод: | B223 2873 |
| Деталь: | Tension Spring:Side Fence:Rear |
| Парткод: | AA06 1003 |
| Деталь: | GROUND PLATE |
| Парткод: | B223 2869 |
| Деталь: | Toner Cartridge Unit |
| Парткод: | B223 3305 |
| Деталь: | Toner Cartridge Guide |
| Парткод: | B223 3328 |
| Деталь: | Rail:Left:Intermediate Transfer |
| Парткод: | G133 6145 |
| Деталь: | Rail:Right:Intermediate Transfer |
| Парткод: | G133 6146 |
| Деталь: | Sheet:Harness |
| Парткод: | B223 4342 |
| Деталь: | Slide Rail:Fusing Unit |
| Парткод: | AA07 0080 |
| Деталь: | Sponge:IH:Fan |
| Парткод: | B223 1344 |
| Деталь: | Bracket:Sensor:Front |
| Парткод: | B223 1067 |
| Деталь: | Bracket:Sensor:Rear |
| Парткод: | B223 1068 |
| Деталь: | Cover:Thermopile |
| Парткод: | B223 4331 |
| Деталь: | Thermopile |
| Парткод: | AW10 0106 |
| Деталь: | Harness:IOB:Fusing:Thermopile |
| Парткод: | B223 5312 |
| Деталь: | Holder:Thermopile |
| Парткод: | B223 4332 |
| Деталь: | Stay:Temperature Sensor:Fusing |
| Парткод: | B223 4314 |
| Деталь: | Positioning Plate:Fusing Unit |
| Парткод: | B223 4391 |
| Деталь: | Cover:Connector:Heater |
| Парткод: | B223 5849 |
| Деталь: | Cover - Connector |
| Парткод: | B223 2727 |
| Деталь: | Cover - Positioning Pin |
| Парткод: | B238 1089 |
| Деталь: | Set Sensor Bracket |
| Парткод: | B223 6507 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Tray Cover - Right |
| Парткод: | B238 2541 |
| Деталь: | Tray Cover - Middle |
| Парткод: | B238 2544 |
| Деталь: | Harness - Paper Volume Sensor |
| Парткод: | B238 5325 |
| Деталь: | DC Motor 24V |
| Парткод: | AX04 0154 |
| Деталь: | Paper Tray Stopper Assy |
| Парткод: | B223 2730 |
| Деталь: | Rear Pipe Assy |
| Парткод: | B223 6481 |
| Деталь: | Drive Unit:Collection Bottle |
| Парткод: | B223 1174 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0722 |
| Деталь: | Pulley:Idler:Fusing |
| Парткод: | AB03 0551 |
| Деталь: | Pulley - 34T |
| Парткод: | AB03 0783 |
| Деталь: | Timing Belt - S2M460 |
| Парткод: | AA04 3583 |
| Деталь: | COVER |
| Парткод: | B223 2722 |
| Деталь: | Bracket:Push Switch |
| Парткод: | B223 2721 |
| Деталь: | Push Switch:Paper Size Sensor |
| Парткод: | AW50 0038 |
| Деталь: | Cover - Tray Left |
| Парткод: | B238 2543 |
| Деталь: | Bracket:Base:Connector |
| Парткод: | B223 5848 |
| Деталь: | Sheet:Main Switch |
| Парткод: | B238 5828 |
| Деталь: | Bracket:Main Switch |
| Парткод: | B238 5827 |
| Деталь: | Harness:AC:Switch |
| Парткод: | B223 5330 |
| Деталь: | Cover - Connector |
| Парткод: | B238 1088 |
| Деталь: | Connector bracket |
| Парткод: | B223 1065 |
Коды ошибок
195
202
203
204
210
211
212
213
220
221
222
223
224
225
226
227
230
231
232
233
234
235
236
237
240
241
242
243
285
290
291
292
293
294
295
296
300
301
302
303
360
361
362
363
364
365
366
367
372
373
374
375
380
396
397
398
399
400
441
442
443
452
460
490
491
492
498
501
502
503-01
503-02
504-01
504-02
505-01
505-02
529
530
531
532
533
534
535
536
540
541
542
543
544
547
548
549
551
552
553
554
557
559
561
562
563
564
565
580
581
582
583
584
585
586
587
610
611
621
622
623
669
670
681
682
683
687
689
690
721
723
725
730
740
741
742
743
744
746
750
753
760
761
763
764
791
792
818
819
820
821
822
823
824
826
827
828
829
851
853
854
855, 856
857
860
861
863
864
865
866
867
868
870
872
873
874
875
876
877
900
920
921
990
991
992
998
Описание
| Error code: | 195 |
| Description: | Serial Number Error |
| Causes: | The serial number stored in the memory (EGB) is not correct. |
| Remedy: | EEPROM defective EGB replaced without original EEPROM |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 204 |
| Display: | Power OFF/ON 204:Error |
| Description: | Polygon motor error 3: XSCRDY signal error |
| Causes: | The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing. |
| Remedy: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board). |
| Error code: | 210 |
| Description: | EM Null page cargo |
| Causes: | • Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB |
| Remedy: | 1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 211 |
| Display: | ERROR 211 HeadWARM.THERM(----) |
| Description: | EM Null page |
| Causes: | • Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB |
| Remedy: | 1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 212 |
| Description: | Install or Reseat Imaging Unit The Imaging Unit CRUM fails to detect the Imaging Unit. |
| Causes: | • Imaging Unit, PL6.1.1 • CRUM Connector, PL7.1.4 • PHD2 Harness, PL7.1.7 • FAN/PHD/MOT Harness, PL10.1.9 |
| Remedy: | 1 Remove the Imaging Unit. Inspect the printer cavity for damage, debris, and toner under the auger area preventing the Imaging Unit from being seated properly. Is there foreign material or damage? Remove foreign material. Vacuum out loose toner if found. Go to Step 2. 2 Inspect and reseat the Imaging Unit. Does the error persist?. Go to Step 3. Complete 3 Check Imaging Unit CRUM connection. Are P/J710 and P/J484 connected? Go to Step 4. Reconnect the CRUM. 4 Check all pins on the PHD2 Harness PL7.1.7 for continuity. 1. Disconnect P/J710 and P/J484. 2. Check continuity between J484<=>J710. Go to Step 5 Replace PHD2 Harness. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J484 and P/J48. 2. Check continuity between J48 <=> P484. Go to Step 6 Replace the FAN/PHD/MOT Harness 6 Replace the Imaging Unit. Does the error persist? Replace the Engine Control Board. Complete |
| Error code: | 213 |
| Display: | Power OFF/ON 213:Error |
| Description: | Install or Reseat Transfer Roller The printer does not detect the presence of the Transfer Roller. |
| Causes: | • CTD (ADC) Sensor, PL5.2.19 • Transfer Roller, PL5.1.4 • FSR/ADC Harness, PL5.2.28 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Transfer Roller PL5.1.4 • CTD (ADC) Sensor PL5.2.19 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Clean the CTD (ADC) Sensor. Does this fix the problem? Complete Go to Step 3. 3 Test the CTD (ADC) Sensor. Run the Service Diagnostics CTD (ADC) Sensor test. Does the sensor function correctly? Go to Step 4. Go to Step 5. 4 Replace the Transfer Roller. Does the error persist? Go to Step 5. Complete 5 Check the CTD (ADC) Sensor connection. Is P/J136 connected to the harness? Go to Step 6. Connect the sensor. 6 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J136. 2. Check continuity between J36 <=> J136. Go to Step 7. Replace the FSR/ ADC Harness. 7 Check the CTD (ADC) Sensor signal. Disconnect P/J36. Does J36-2 <=> J36-5 = 0 V? Replace the CTD (ADC) Sensor. Replace the Engine Control Board. |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 221 |
| Description: | Laser synchronizing detection error: start position [K]: LD1 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 222 |
| Description: | Laser Synchronizing Detection Error: [M]/[C] |
| Causes: | The laser synchronizing detection signal for LDB [M]/[C] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Remedy: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB 1. Check the connectors. 2. Replace the laser optics unit. 3. Replace the EGB.· |
| Error code: | 223 |
| Description: | Metered Toner Is not Enabled A metered toner cartridge is installed while metered toner is not enabled. |
| Causes: | • Toner Cartridge (Y) PL7.2.8 • Toner Cartridge (M) PL7.2.9 • Toner Cartridge (C) PL7.2.10 • Toner Cartridge (K) PL7.2.11 |
| Remedy: | 1 Check the configuration of the Printer. Is the printer covered under a Metered Toner contract? Enable the Metered Toner via the front Panel. Replace the affected Toner Cartridge with a Non-Metered Toner Cartridge. |
| Error code: | 224 |
| Description: | Laser synchronizing detection error: start position [M]: LD0 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 225 |
| Description: | +24V Not Available to the Duplex Unit Abnormal current indicates that +24 V is not being supplied to the Duplex Unit. Applicable Status Code: Code 225: Duplex Unit is not receiving +24 V. |
| Causes: | • Motor Driver Board, PL2.1.10 • LVPS, PL3.1.1 • Duplex Unit, PL16.1.1A |
| Remedy: | 1 Check the Duplex Unit connector for damage. Is the connector damaged? Replace the connector. Go to Step 2. 2 Check for +24 V at DUPLEX on the Motor Driver Board. 1. Close the Interlock Switches. 2. Disconnect DUPLEX. Is there +24 V at DUPLEX-6 and -13 <=> ground? Replace the Duplex Control Board. Go to Step 3. 3 Check all pins on the DUPLEX Harness for continuity. Disconnect the DUPLEX Harness. Is the DUPLEX Harness conductive? Go to Step 4. Replace the DUPLEX Harness. 4 Check for +24 V from the LVPS. Disconnect POW24 on the Motor Driver Board. Is there +24 V at POW24-1 <=> ground? Replace the Motor Driver Board Go to Step 5. 5 Check the LVPS +24 V output. 1. Close the Interlock Switches. 2. Disconnect CN2. Is there +24 V at CN2-1 and <=> ground? Go to Step 6. Replace the LVPS. 6 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 226 |
| Description: | Laser synchronizing detection error: start position [C]: LD0 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 227 |
| Description: | Finisher Inverter Firmware Error Applicable Status Code: Code 227: A software error with the Inverter’s Flash Memory. |
| Causes: | • Inverter Control Board |
| Remedy: | 1 Check the following for evidence of fault or damage: • Inverter Interface Cable • Inverter connections Is there any damage? Replace any damaged parts. Go to Step 2. 2 Check the Inverter connection. Is the Inverter interface cable securely connected at both ends? Go to Step 3. Connect the Inverter to the Finisher. 3 Check the version of Inverter firmware. Is the latest version installed? Replace the Inverter Control Board. Reload the Inverter firmware. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 231 |
| Display: | Service Call 231: Error |
| Description: | FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 232 |
| Display: | Service call 232: Error |
| Description: | FGATE ON error: Y The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [Y]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 233 |
| Description: | FGATE OFF error: Y • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [Y]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 234 |
| Description: | FGATE ON error: M The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [M]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 235 |
| Description: | FGATE OFF error: M • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [M]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 236 |
| Description: | FGATE ON error: C The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [C]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 237 |
| Description: | FGATE OFF error: C • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [C]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 240 |
| Display: | Service call 240: Error |
| Description: | LD error |
| Causes: | The IPU (EGB) detects a problem at the LD unit. |
| Remedy: | • Worn-out LD • Disconnected or broken harness of the LD. 1. Replace the laser optics unit. |
| Error code: | 241 |
| Display: | Service call 241:Error |
| Description: | LD error: Y The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 242 |
| Display: | Service call 242:Error |
| Description: | LD error: M The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 243 |
| Description: | LD error: C The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 285 |
| Description: | Line position adjustment (MUSIC) error Line position adjustment fails four consecutive times. |
| Causes: | Pattern sampling error (insufficient image density). Defective TD sensors for the line position adjustment. Defective image transfer belt unit. Defective PCDU(s). Defective laser optics housing unit. |
| Remedy: | • Check and reinstall the image transfer belt unit and PCDUs. • Check if each toner bottle has enough toner. • Replace the TD sensor. • Replace the image transfer belt unit. • Replace the PCDU(s). • Replace the laser optics housing unit. |
| Error code: | 290 |
| Description: | Shutter sensor time over error: Close The shutter close sensor does not detect "ON" for 2000 msec after the shutter motor turns on |
| Causes: | • Defective shutter close sensor • Disconnected or broken harness • Defective shutter motor • Defective shutter • Shutter motor overload • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the shutter on the laser optics housing unit. 3. Replace the shutter motor. 4. Replace the shutter close sensor. 5. Replace the IOB. |
| Error code: | 291 |
| Description: | Shutter overrun error 1: Close The shutter close sensor loses the "ON" signal after the shutter was closed. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 292 |
| Description: | Shutter overrun error 2: Close The shutter close sensor detects "ON" after SC 291 has occurred. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 293 |
| Description: | Shutter sensor time over error: Open The shutter open sensor does not detect "ON" for 2000 msec after the shutter motor turns on. |
| Causes: | • Defective shutter close sensor • Disconnected or broken harness • Defective shutter motor • Defective shutter • Shutter motor overload • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the shutter on the laser optics housing unit. 3. Replace the shutter motor. 4. Replace the shutter close sensor. 5. Replace the IOB. |
| Error code: | 294 |
| Description: | Shutter overrun error 1: Open The shutter open sensor loses the "ON" signal after the shutter was closed. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 295 |
| Description: | Shutter overrun error 2: Open The shutter open sensor detects "ON" after SC 291 has occurred. |
| Causes: | • Defective motor • Change of load to shutter motor |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 296 |
| Description: | Shutter open/close sensor error Both shutter open sensor and close sensor detect "ON" at the same time. |
| Causes: | • Broken harness(es) of the shutter open/close sensors |
| Remedy: | Replace the shutter on the laser optics housing unit. |
| Error code: | 300 |
| Description: | High voltage power output error |
| Causes: | The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit). |
| Remedy: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB. |
| Error code: | 301 |
| Description: | Fuser web must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 303 |
| Display: | SYSTEM HALT (*) 303 : PCB MAIN ET |
| Description: | AC charge output error [Y] The measured voltage is not proper when IOB measures the charge output for each color. |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 360 |
| Display: | Set duplex unit 360: Duplex unit is open. |
| Description: | When duplex unit is removed from printer. |
| Causes: | Does error recover by resetting duplex unit? |
| Remedy: | Normal. Replace duplex unit or engine board. |
| Error code: | 361 |
| Description: | TD sensor (Vt high) error 1: M • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 362 |
| Description: | TD sensor (Vt high) error 1: C • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 363 |
| Description: | TD sensor (Vt high) error 1: Y • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 364 |
| Description: | TD sensor (Vt low) error 2: K The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 365 |
| Description: | TD sensor (Vt low) error 2: M The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 366 |
| Description: | TD sensor (Vt low) error 2: C The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 367 |
| Description: | TD sensor (Vt low) error 2: Y The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 372 |
| Display: | Check DUPLEX 372: Paper jam |
| Causes: | Check miss-feed in duplex unit. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace duplex unit. |
| Error code: | 373 |
| Description: | TD sensor adjustment error: M During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 374 |
| Description: | TD sensor adjustment error: C During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 375 |
| Description: | TD sensor adjustment error: Y During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 380 |
| Display: | Open front cover 380: Paper jam |
| Description: | Paper jam during paper feed from cassette 1, 2, 3, 4 or 5 |
| Causes: | Check miss-feed in duplex unit. |
| Remedy: | Remove miss-fed paper and set cassette. Check/replace cassette 1, 2, 3, 4, or 5. |
| Error code: | 396 |
| Description: | Black drum motor error |
| Causes: | The LOCK signal error is detected when the EGB monitors the black drum motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the black drum motor. Replace it if necessary.e hig |
| Error code: | 397 |
| Description: | Color drum motor error |
| Causes: | The LOCK signal error is detected when the EGB monitors the color drum motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the color drum motor. Replace it if necessary. |
| Error code: | 398 |
| Description: | Drum/Development motor error: C The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on. |
| Causes: | • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system |
| Remedy: | 1. Check or replace the harness. 2. Replace the drum/development motor. 3. Replace the 24V fuse on the PSU. |
| Error code: | 399 |
| Description: | Drum/Development motor error: Y The machine detects a High signal from the drum/development motor for 2 seconds after the drum/development motor turned on. |
| Causes: | • Overload on the drum/development motor • Defective drum/development motor • Defective harness • Shorted 24 V fuse on the PSU • Defective interlock system |
| Remedy: | 1. Check or replace the harness. 2. Replace the drum/development motor. 3. Replace the 24V fuse on the PSU. |
| Error code: | 400 |
| Display: | Open top cover 400: Paper size error |
| Description: | TM sensor error |
| Causes: | The CPU detected a low voltage of the positive reflection output under the threshold in the TM sensor. |
| Remedy: | • TM sensors are dirty. • A solid print out due to an electrostatic charging error • The TM sensor is defective. 1. Clean the TM sensors. 2. Replace the TM sensors. 3. Check the image transfer unit. 4. Turn the power Off and On. |
| Error code: | 441 |
| Description: | Image transfer unit motor error When the motor is ON, the machine monitors the lock signals every 100 ms. If the High status occurs 20 times consecutively, the machine judges that the motor is not rotating correctly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Shorted 24 V fuse on the PSU. Defective interlock systeme PSU. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system |
| Error code: | 442 |
| Description: | Image transfer belt contact motor error The image transfer belt contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates. |
| Causes: | Motor overload. Defective motor. Loose connection. Disconnected harness. Shorted 24 V fuse on the PSU. Defective interlock system. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Replace the interlock switch. • Replace the IOB. |
| Error code: | 443 |
| Description: | Image transfer unit error The machine detects the encoder sensor error. |
| Causes: | Defective encoder sensor. Defective image transfer unit motor. Image transfer unit installation error. Loose connection. Broken harness. |
| Remedy: | • Replace the image transfer unit. • Replace the image transfer unit motor. • Reinstall the image transfer unit. • Replace the encoder sensor. • Reconnect the connector. • Replace the harness. |
| Error code: | 452 |
| Description: | Paper transfer unit contact error The paper transfer unit contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates. |
| Causes: | Motor overload. Defective motor. Loose connection. Disconnected harness. Shorted 24 V fuse on the PSU. Defective interlock system. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system. • Replace the IOB. |
| Error code: | 460 |
| Description: | DC Separation Corona Output Error A dc separation feedback voltage of less than 0.5 V was detected after more than 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 490 |
| Display: | Set 490: No paper in MP tray (* stands for A4 B4, etc.) |
| Description: | ITB (Image Transfer Belt) Unit Set Error |
| Causes: | The TM sensor does not detect the reflection from the ITB. |
| Remedy: | • No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S |
| Error code: | 491 |
| Description: | High voltage power: Drum / development bias output error An error signal is detected for 200 ms when charging the drum or development. |
| Causes: | High voltage leak. Loose connection. Broken harness. Defective drum unit or development unit. Defective high voltage supply unit. |
| Remedy: | • Turn the main power switch off and on. • Reattach/replace the harness and parts on the high voltage power supply route. • Replace the drum unit or development unit. • Replace the high voltage supply unit. |
| Error code: | 492 |
| Description: | High voltage power: Image transfer / paper transfer bias output error An error signal is detected for 200 ms when charging the separation, image transfer bet or paper transfer roller. |
| Causes: | High voltage leak. Broken harness Defective image transfer belt unit or paper transfer unit. Defective high voltage supply unit. |
| Remedy: | • Turn the main power switch off and on. • Reattach/replace the harness and parts on the high voltage power supply route. • Replace/reinstall the high-voltage supply unit. • Replace the high voltage supply unit. |
| Error code: | 498 |
| Description: | Temperature and humidity sensor error 2 Thermal sensor output error: If the output value is 0.5 V or lower or 3.0 V or higher, it is judged as a sensor error and the presumptive temperature, 23C, is applied. Humidity sensor output error: If the output value is 2.4V or higher, it is judged as a sensor error and the presumptive humidity, 50 % RH, is applied. If a sensor error is judged to have occurred to the thermal sensor or humidity sensor three times consecutively, the machine issues SC498-00. * However, if the power is switched off and then back on, the machine resumes its attempt to use the sensor. * If the thermal sensor or humidity sensor remains capable of normal operation even after the SC is issued, the capable sensor will keep operating. |
| Causes: | Loose connection/harness disconnected. Defective sensor. |
| Remedy: | • Reconnect to the connector. • Check the harness. |
| Error code: | 501 |
| Display: | Service Call 501: Error |
| Description: | Tray 1 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503-01 |
| Description: | Tray 3 error (Paper Tray Unit, Paper Feed Unit or LCT) For the two-tray paper feed unit or one-tray paper tray unit: • When the tray lift motor is turned on, the upper limit is not detected within 10 seconds For the LCT: • SC 503-01 occurs if the upper or lower limit is not detected within 8 seconds when the tray lift motor is turned on to lift or lower the tray. |
| Causes: | For the two-tray paper feed unit or one-tray paper tray unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection • Defective upper limit sensor or connector disconnection • Defective tray lift motor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 503-02 |
| Description: | Tray 3 error (Paper Tray Unit, Paper Feed Unit or LCT) This SC is generated if the following condition occurs 3 consecutive times. For the two-tray paper feed unit or one-tray paper tray unit: • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. For the LCT: • When the main switch is turned on or when the LCT is set, if the end fence is not in the home position (home position sensor ON), the tray lift motor stops. • If the upper limit does not go off for 1.5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on. |
| Causes: | For the two-tray paper feed unit or one-tray paper tray unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 504-01 |
| Description: | Tray 4 error (Paper Tray Unit, Paper Feed Unit or LCT) For the two-tray paper feed unit or one-tray paper tray unit When the tray lift motor is turned on, the upper limit is not detected within 10 seconds. For the LCT If the upper or lower limit is not detected within 8 seconds when the tray lift motor is turned on to lift up or lower the tray |
| Causes: | • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 504-02 |
| Description: | Tray 4 error (Paper Tray Unit, Paper Feed Unit or LCT) This SC is generated if the following condition occurs 3 consecutive times. For the two-tray paper feed unit or one-tray paper tray unit • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. For the LCT • If the upper limit does not go off for 1.5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on. |
| Causes: | For the two-tray paper feed unit or one-tray paper tray unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 505-01 |
| Description: | Tray 5 error (Two-tray paper feed unit combined with the one-tray paper tray unit) When the tray lift motor is turned on, the upper limit is not detected within 10 seconds. |
| Causes: | • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 505-02 |
| Description: | Tray 5 error (Two-tray paper feed unit combined with the one-tray paper tray unit) This SC is generated if the following condition occurs 3 consecutive times. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. |
| Causes: | • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection |
| Remedy: | 1. Check the cable connections. 2. Check and/or replace the defective component. |
| Error code: | 529 |
| Description: | Junction gate 1 motor error The junction gate 1 HP sensor does not detect the home position of junction gate 1 for 0.15 seconds when the machine starts to detect its home position. The junction gate 1 HP sensor does not turn off for 0.15 seconds after the machine has detected its home position. |
| Causes: | • Disconnected or defective junction gate 1 motor • Disconnected or defective junction gate 1 HP sensor • Mechanical problem (such as paper jam etc.) • Shorted 24 V fuse on the PSU • Defective IOB |
| Remedy: | 1. Remove any objects that obstruct junction gate 1. 2. Replace the junction gate 1 HP sensor. 3. Replace the junction gate 1 motor. 4. Replace the 24 V fuse on the PSU. 5. Replace the IOB. |
| Error code: | 530 |
| Description: | LSU Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the LSU fan motor. |
| Error code: | 531 |
| Description: | Fusing Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the fusing fan motor. |
| Error code: | 532 |
| Description: | IH coil fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH coil fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH coil fan motor • Defective IH coil fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH coil fan. 3. Replace the IOB. |
| Error code: | 533 |
| Description: | IH inverter fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH inverter fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH inverter fan motor • Defective IH inverter fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH inverter fan. 3. Replace the IOB. |
| Error code: | 534 |
| Description: | Second duct fan error The machine does not detect the fan motor lock signal for 2 seconds while the second duct fan turns on. |
| Causes: | • Disconnected harness • Overload on the second duct fan motor • Defective second duct motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the second duct fan. 3. Replace the IOB. |
| Error code: | 535 |
| Description: | Paper exit fan error The lock sensor value is monitored every 100 ms when the motor is ON. If the retrieval of the lock signal fails 100 times consecutively, it is determined as a failure to rotate properly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 536 |
| Description: | Third duct fan error The motor lock signal error is detected for 10 seconds after the motor lock signal was first detected. |
| Causes: | • Defective controller fan motor |
| Remedy: | 1. Replace the controller fan motor. 2. Replace the IOB. |
| Error code: | 540 |
| Description: | Fusing/Paper exit motor error At the fusing delivery brushless motor, the lock signal is monitored every 100 ms. If the High status occurs consecutively 20 times, it is determined as a failure to rotate properly. |
| Causes: | Motor overload. Defective motor. Loose connection. Broken harness. Shorted 24 V fuse on the PSU. Defective interlock system. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 548 |
| Description: | Low Temperature Error |
| Causes: | The center thermistor detects 100°C or less for 4 seconds. |
| Remedy: | • Defective fusing lamp • Defective thermistor 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.d |
| Error code: | 549 |
| Description: | Fusing heater connection error The fusing sleeve belt rotation sensor detects the target temperature as 50°C for 5 seconds or more after the fusing/paper exit motor has turned on. |
| Causes: | Broken heater cables. Loose connection. |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 554 |
| Description: | Fusing sleeve belt overheat: End (hardware error) The fusing sleeve belt thermistor detects 250°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 561 |
| Description: | Pressure roller end thermistor error 1 During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the end thermistor on the pressure roller returned a digital reading of more than 3.3V. |
| Causes: | • Pressure roller end thermistor not positioned properly • Pressure roller end thermistor connector loose, broken, defective • Pressure roller end thermistor defective • MCU defective |
| Error code: | 562 |
| Description: | Pressure roller temperature error The temperature of the pressure roller does not reach the ready temperature for 120 seconds after the fusing lamp has turned on. |
| Causes: | • Defective pressure roller thermistor • Defective fusing lamp |
| Remedy: | 1. Clean the thermopile. 2. Replace the thermistor for the pressure roller. 3. Replace the pressure roller fusing lamp. |
| Error code: | 563 |
| Description: | Pressure roller end thermistor error 2 During the hot roller temperature control sequence, the end thermistor on the pressure roller returned a digital reading of less than 0.2V. |
| Causes: | • Pressure roller end thermistor connector loose • Pressure roller end thermistor short circuit, defective • MCU defective |
| Error code: | 564 |
| Description: | Pressure roller overheat: End (hardware error) The thermistor detects 240°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: • The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 565 |
| Description: | Pressure roller fusing lamp consecutive full power 3 When the fusing unit is not running in the ready condition, the pressure roller fusing lamp keeps ON full power for 180 seconds or more. |
| Causes: | • Broken pressure roller fusing lamp |
| Remedy: | 1. Replace the pressure roller fusing lamp. 2. Replace the pressure roller thermistor. 3. Replace the PSU. |
| Error code: | 580 |
| Description: | IH inverter zero cross frequency error The zero cross signal is not detected for 1 second or more after the IH inverter has turned on. |
| Causes: | • Disconnected CN983 on the IH inverter • Defective IH inverter • Defective IH coil unit |
| Remedy: | 1. Check CN983 on the IH inverter. 2. Replace the IH inverter. 3. Replace the IH coil unit. |
| Error code: | 581 |
| Description: | NC sensor broken: Center The sensor detects -17°C or less for 6 seconds |
| Causes: | Defective thermopile. Defective thermistor. Loose connection. |
| Error code: | 582 |
| Description: | IH inverter current error at power on The output current from the IH inverter does not reach the proper value when the IH inverter turns on. |
| Causes: | • Disconnected power input terminal 1 and 2 • Defective IH inverter • Defective IH coil unit • Defective fusing unit |
| Remedy: | 1. Check the power input terminals 1 and 2. 2. Replace the IH inverter. 3. Replace the IH coil unit. 4. Replace the fusing unit. |
| Error code: | 583 |
| Description: | IH inverter communication error The IH inverter does not get the communication signal from the IOB. |
| Causes: | • Broken connection between IH inverter and IOB • Defective IH inverter • Defective IOB • Defective EGB |
| Remedy: | 1. Check the connection between IH inverter and IOB 2. Replace the IH inverter. 3. Replace the IOB. 4. Replace the EGB. |
| Error code: | 584 |
| Description: | Fusing unit rotation error The fusing belt sensor does not detect a change in the fusing unit actuator for 0.5 seconds. |
| Causes: | • Defective fusing/paper exit motor • Deformed actuator for the fusing belt sensor • Defective fusing belt sensor • Broken connection between IH inverter and IOB • Incorrectly set fusing unit |
| Remedy: | 1. Check if the fusing unit is correctly set. 1. Check or replace the actuator for fusing belt sensor. 2. Replace the fusing belt sensor. 3. Replace the IH inverter. 4. Check the connection between IH inverter and IOB. |
| Error code: | 585 |
| Description: | IH coil unit full power (1250W) error The IH coil unit full power (1250W) continues for 220 seconds or more. |
| Causes: | • Defective IH inverter • Defective EGB • Defective IOB • Broken connection between IH inverter and IOB • Defective thermopile |
| Error code: | 586 |
| Description: | IH coil unit rare short error The IH inverter detects an unusual current (high current) in the IH coil unit. |
| Causes: | • Defective IH coil unit • Defective IH inverterl unit |
| Remedy: | 1. Replace the IH coil unit. 2. Replace the IH inverter. |
| Error code: | 587 |
| Description: | IH inverter high temperature error The IH inverter detects a high temperature near Q5 (power control circuit on the IH inverter). |
| Causes: | • Defective IH inverter • Defective IH inverter fan • Clogged IH inverter fan intake at the right rear cover • Incorrect input paper type to the machine |
| Remedy: | 1. Check or clean the IH inverter fan intake. 2. Set the correct paper type on the operation panel. 3. Replace the IH inverter. 4. Replace the IH inverter fan. |
| Error code: | 610 |
| Display: | ERROR 610 NOT FILLUP |
| Description: | Mechanical counter error: Bk This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 611 |
| Display: | ERROR 611 Case Weight |
| Description: | Mechanical counter error: FC This SC is only for NA models. The machine detects the mechanical counter error when SP5987-001 is set to "1". |
| Causes: | • Disconnected mechanical counter • Defective mechanical counter |
| Remedy: | 1. Check or replace the mechanical counter. |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 622 |
| Description: | Paper Bank communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The paper bank`s control board is faulty. Defective BCU/IOB. The paper bank`s connection is faulty. |
| Remedy: | • Reconnect the paper bank cables. • Replace the BCU. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 623 |
| Description: | 2nd Paper Bank communication error An error code is issued from the paper bank unit. |
| Causes: | Loose connection. Defective paper bank. |
| Remedy: | • Reconnect the connector. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 669 |
| Description: | EEPROM Error |
| Causes: | An unexpected value exists in the initialization flag of the EEPROM |
| Remedy: | • EEPROM not initialized • Defective EEPROM |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 681 |
| Description: | Toner bottle ID: Communication error -01 D Device ID is not identified: K -02 D Device ID is not identified: M -03 D Device ID is not identified: C -04 D Device ID is not identified: Y -06 D Channel error: K -07 D Channel error: M -08 D Channel error: C -09 D Channel error: Y -11 D Device error: K -12 D Device error: M -13 D Device error: C -14 D Device error: Y -16 D Communication interruption (an error during communication): K -17 D Communication interruption (an error during communication): M -18 D Communication interruption (an error during communication): C -19 D Communication interruption (an error during communication): Y -21 D Communication time-out: K -22 D Communication time-out: M -23 D Communication time-out: C -24 D Communication time-out: Y -26 D Device operation suspended (logically suspended): K -27 D Device operation suspended (logically suspended): M -28 D Device operation suspended (logically suspended): C -29 D Device operation suspended (logically suspended): Y -31 D The requested buffer is full: K -32 D The requested buffer is full: M -33 D The requested buffer is full: C -34 D The requested buffer is full: Y -36 D No error code: K -37 D No error code: M -38 D No error code: C -39 D No error code: Y |
| Causes: | Communication error occurs when the toner bottle ID starts to communicate with the toner bottle ID receptor. Retry of toner bottle ID communication fails three times after the machine has detected the toner bottle ID communication error. • 01-04 Damaged memory chip data • 06-09 Disconnected interface • 11-14 No memory chip on the toner cartridge • 16-9, 21-24, 26-39 Caused by noise • 31-34, 36-39 Software problem • Replace the toner bottle detection board. • Replace the toner cartridge. • Turn the main power switch off and on. |
| Error code: | 682 |
| Description: | Memory chip at TD sensor: Communication error |
| Causes: | • 01-04 Damaged memory chip data • 06-09 Disconnected interface • 11-14 No memory chip on the toner cartridge • 16-19, 21-24, 26-39 Caused by noise • 31-34, 36-39 Software problem |
| Remedy: | • Replace the PCU. • Turn the main power switch off and on. |
| Error code: | 683 |
| Description: | RFID: Unit check error The machine gets RFID communication error even the toner cartridges have not been installed in the machine |
| Causes: | Caused by noise |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 689 |
| Description: | IH inverter communication error • When the machine turns on, recovers from the energy save mode or front and right doors are opened and closed, a time out error for communicating with the IOB occurs. • The IOB detects the break signal from the IH inverter after a communication between the IOB and IH inverter has already been detected. • The IOB fails to communicate with IH inverter three times after the IOB has detected the break signal from the IH inverter. |
| Causes: | • Defective IOB • Defective IH inverter. |
| Remedy: | 1. Turn the main power switch off and on. 2. If the error occurs again, replace the IOB and/or the IH inverter. |
| Error code: | 690 |
| Description: | GAVD Communication Error |
| Causes: | The ID of the GAVD is not identified during initialization. The chip ID of the GAVD cannot be detected by the machine at power-on. |
| Remedy: | • Defective EGB 1. Replace the EGB. EE |
| Error code: | 721 |
| Description: | Jogger motor error • Jogger HP sensor does not detect the jogger fence for 2000ms after the jogger unit has moved to its home position. • Jogger HP sensor does not turn off 300 ms after the jogger unit has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective jogger HP sensor • Overload on the jogger motor • Defective jogger motor • Defective main board • Disconnected or defective harness |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the jogger HP sensor (if the jogger motor works correctly). 3. Replace the jogger motor (if the jogger motor does not work). 4. Replace the finisher main board. |
| Error code: | 723 |
| Description: | Stack feed-out motor error • Stack feed-out HP sensor does not detect the home position of the stack feedout belt 3000ms after the stack feed-out belt has moved to its home position. • Stack feed-out HP sensor does not turn off 200 ms after the stack feed-out belt has moved from its home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code |
| Causes: | • Defective stack feed-out HP sensor • Overload on the stack feed-out motor • Defective stack feed-out motor • Defective main board • Disconnected or defective harness |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the stack feed-out HP sensor (if the stack feed-out motor works correctly). 3. Replace the stack feed-out motor (if the stack feed-out motor does not work). 4. Replace the finisher main board. |
| Error code: | 725 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor. 4. Replace the finisher main board. |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 740 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished after a certain time. For the 1000-sheet booklet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 741 |
| Description: | Finisher corner stapler rotation motor error The stapler does not return to its home position within the specified time after stapling. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective stapler rotation motor • Overload to the stapler rotation motor • Defective stapler rotation HP sensor |
| Remedy: | 1. Replace the stapler rotation motor. 2. Replace the stapler rotation HP sensor. |
| Error code: | 742 |
| Description: | Finisher stapler movement motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished for a certain time. For the 1000-sheet booklet finisher • The stapler HP sensor is not activated within the specified time after the stapler motor turned on. (first detection: jam error, consecutive twice detection SC code). |
| Causes: | • Motor overload • Loose connection of the stapler home position sensor • Loose connection of the stapler movement motor • Defective stapler home position sensor • Defective stapler movement motor |
| Remedy: | 1. Check the connection of the stapler movement motor. 2. Check the connection of the stapler home position sensor. 3. Replace the stapler home position sensor. 4. Replace the stapler movement motor. |
| Error code: | 743 |
| Description: | Booklet stapler motor error 1 The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher The front stapler unit saddle-stitch motor does not start operation within the specified time. |
| Causes: | • Motor overload • Loose connection of the front stapler motor • Defective front stapler motor |
| Remedy: | Replace the front stapler motor. |
| Error code: | 744 |
| Description: | Booklet staple motor error 2 The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher The rear stapler unit saddle-stitch motor does not start operation within the specified time. |
| Causes: | • Motor overload • Loose connection of the rear stapler motor • Defective rear stapler motor |
| Remedy: | Replace the front stapler motor. |
| Error code: | 746 |
| Description: | 1000-sheet booklet finisher: Stack feed motor error • The stack feed HP sensor does not detect "ON" twice (once: jam error) for specified time after the stack feed motor has turned on. • The stack feed HP sensor does not detect "OFF" twice (once: jam error) for specified time after the stack feed motor has turned on. |
| Causes: | • Motor overload • Loose connection of the stack feed motor • Defective stack feed motor |
| Remedy: | 1. Check the connections and cables for the stack feed motor and HP sensor. 2. Check for blockages in the stack feed motor mechanism. 3. Replace the stack feed HP sensor and/or stack feed motor 4. Replace the finisher main board. |
| Error code: | 750 |
| Description: | 1000/3000-sheet (booklet) finisher: Tray lift motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. |
| Causes: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor |
| Remedy: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor. |
| Error code: | 753 |
| Description: | Return roller motor error Occurs during the operation of the lower tray pressure motor. |
| Causes: | • Motor harness disconnected, loose, defective • Motor overloaded • Home position sensor harness disconnected, loose, defective • Home position defective |
| Remedy: | 1. Check the connections of the stacking sponge roller motor. 2. Check the connections of the stacking sponge roller HP sensor. 3. Replace the stacking sponge roller motor. 4. Replace the stacking sponge roller HP sensor. |
| Error code: | 760 |
| Description: | Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Punch HP sensor disconnected, defective • Punch motor disconnected or defective • Punch motor overload due to obstruction |
| Remedy: | 1. Check the connections and cables for the punch motor and HP sensor. 2. Check for blockages in the punch motor mechanism. 3. Replace the punch HP sensor and/or punch motor 4. Replace the finisher main board. |
| Error code: | 761 |
| Description: | Finisher folder plate motor error The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Remedy: | 1. Check the connections and cables for the folder plate motor and HP sensor. 2. Check for blockages in the folder plate motor mechanism. 3. Replace the folder plate HP sensor and/or folder plate motor 4. Replace the finisher main board. |
| Error code: | 763 |
| Description: | Rear fold plate HP sensor error The state (on/off, off/on) of the rear fold plate HP sensor in the fan fold unit did not change 1 sec. after the plate started to move. |
| Causes: | • Fold plate motor (R) harness connector loose, disconnected, broken • Rear fold plate HP sensor harness connector loose, disconnected, broken • Fold plate motor (R) defective • Rear fold plate HP sensor defective • Undetected paper is jamming the action of the motor or fold plate • Fan folder unit MCU defective |
| Error code: | 764 |
| Description: | Paper position sensor slide motor error The paper position sensor moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Defective motor |
| Remedy: | 1. Check the connections to the paper position sensor slide motor. 2. Replace the paper position sensor slide motor. |
| Error code: | 791 |
| Description: | Bridge unit error The machine recognizes the finisher, but does not recognize the bridge unit. |
| Causes: | The bridge unit is not installed. Defective bridge unit. Re-install the bridge unit. Turn the main power switch off and on. |
| Remedy: | • Re-install the bridge unit. • Turn the main power switch off and on. |
| Error code: | 792 |
| Description: | Finisher error The machine does not recognize the finisher, but recognizes the bridge unit. |
| Causes: | The finisher`s connection is faulty. The finisher is not attached to a device equipped with the bridge unit. Defective finisher. |
| Remedy: | Reconnect the finisher or bridge unit, and then turn the main power switch off and then back on. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855, 856 |
| Description: | Wireless LAN/Bluetooth card error An error is detected in the wireless LAN/Bluetooth card. |
| Causes: | • Loose connection • Defective wireless LAN/Bluetooth card |
| Remedy: | 1. Check the connection. 2. Replace the wireless LAN/Bluetooth card. |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 877 |
| Description: | HDD Data Erase Error The Data Overwrite Security option cannot scramble and erase data on the HDD because the DOS SD card has been corrupted or has |
| Causes: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not been removed from the SD card slot. |
| Remedy: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not solve the problem, the SD card has been damaged.) • Install a new NVRAM • Install a new Data Overwrite Security option with a new SD card |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
Парткод
Название
RICOH SP-C811 Блок фотобарабана / девелопера черный
RICOH SP-C811 Блок фотобарабана / девелопера CMY
RICOH SP-C811 Емкость для отработанного тонера
RICOH SP-C811 Блок переноса
RICOH SP-C811 Блок термозакрепления 230v
RICOH TYPE K Скрепки с картриджем
RICOH TYPE K Скрепки (3 упаковки)
RICOH TYPE S Скрепки буклетные в картридже для SR3000
RICOH SP-C811DNHE Принт-картридж черный (20000 стр.)
RICOH SP-C811DNHE Принт-картридж желтый (15000 стр.)
RICOH SP-C811DNHE Принт-картридж пурпурный (15000 стр.)
RICOH SP-C811DNHE Принт-картридж голубой (15000 стр.)
RICOH SP-C811DNLE Принт-картридж черный (10000 стр.)
RICOH SP-C811DNLE Принт-картридж желтый (8000 стр.)
RICOH SP-C811DNLE Принт-картридж пурпурный (8000 стр.)
RICOH SP-C811DNLE Принт-картридж голубой (8000 стр.)
