Riso HC5000

Рейтинг

Парткаталог
Коды ошибок

Модули

Duplex Transfer Unit

Ink Bottle Section

COVERS

Maintenance Unit

Drain Tank, Power Supply and Suction Pump

MTPF (2)

MTPF(4)

MTPF(1)

MTPF(5)

PCBs

PS7R

Duplex IN Section

Reservoir Section

REGISTRATION SECTION

MTPF(6)

CCD Unit (Side Registration Section)

MTPF(3)

Vertical Transfer Section

Standard Paper Feed Tray

Flipper Unit

DRIVE SECTION

PRINT HEAD SECTION

MTPF(7)

BP Transfer Section

Exit Section

Guide Plate Section

Scraper Section

Детали

Деталь:	DUPLEX UNIT
Парткод:	033-19255-108

Деталь:	DUPLEX BELT U
Парткод:	033-19256-007

Деталь:	DUPLEX BELT L
Парткод:	033-19257-003

Деталь:	DPX UNIT GEAR
Парткод:	033-19258-000

Деталь:	DPX ROLLER 1
Парткод:	033-19338-003

Деталь:	DPX ROLLER 2
Парткод:	033-19339-000

Деталь:	DPX ROLLER 4
Парткод:	033-19341-004

Деталь:	DPX ROLLER 3
Парткод:	033-19340-008

Деталь:	DPX HANDLE
Парткод:	033-19342-000

Деталь:	DPX KNOB
Парткод:	033-19362-001

Деталь:	INK HOLDER
Парткод:	033-19218-008

Деталь:	BOTTLE JOINT K
Парткод:	033-19219-004

Деталь:	BOTTLE JOINT C
Парткод:	033-19220-002

Деталь:	BOTTLE JOINT M
Парткод:	033-19221-009

Деталь:	BOTTLE JOINT Y
Парткод:	033-19222-102

Деталь:	INFUSE SOLENOID
Парткод:	033-19223-001

Деталь:	IB COVER SWITCH
Парткод:	033-19224-008

Деталь:	PHOTOINTERRUPT
Парткод:	033-19225-004

Деталь:	FILTER ASSY
Парткод:	033-19331-009

Деталь:	SPRING ASSY
Парткод:	033-19332-005

Деталь:	INK TRAY IB
Парткод:	033-19329-004

Деталь:	PHOTOINTERRUPT
Парткод:	033-19225-004

Деталь:	CLEANING UNIT
Парткод:	033-19226-202

Деталь:	INK PAN MOTOR
Парткод:	033-19227-007

Деталь:	Cleaning Motor
Парткод:	033-19228-003

Деталь:	SUCTION HEAD
Парткод:	033-19229-000

Деталь:	STAR WHEEL UNIT
Парткод:	033-19231-101

Деталь:	Torquelimiter
Парткод:	033-19232-000

Деталь:	DUCT
Парткод:	033-19351-000

Деталь:	SPRING 2
Парткод:	033-19350-003

Деталь:	PHOTOINTERRUPT
Парткод:	033-19225-004

Деталь:	SUCTION CHAMBER
Парткод:	033-19233-007

Деталь:	SUCTION PUMP UNIT
Парткод:	033-19234-003

Деталь:	SUCTION TUBE
Парткод:	033-19235-000

Деталь:	PUMP FILTER
Парткод:	033-19236-006

Деталь:	POWER SUPPLY
Парткод:	033-19302-009

Деталь:	FUSE1
Парткод:	033-19303-005

Деталь:	FUSE2
Парткод:	033-19304-001

Деталь:	DRAIN INK TANK
Парткод:	033-19316-301

Деталь:	PUMP SPONGE
Парткод:	033-19324-100

Деталь:	FUSE4
Парткод:	033-19326-005

Деталь:	WST SPRING
Парткод:	033-19330-002

Деталь:	ST TANK
Парткод:	033-19377-009

Деталь:	ROLLER PICKUP
Парткод:	030-21016-100

Деталь:	LOCK RING ROLLER
Парткод:	030-21203-105

Деталь:	Spring Pick-Up Roller
Парткод:	030-21418-004

Деталь:	SIDE FRAME R
Парткод:	033-12055-103

Деталь:	SENSOR GP1A73A
Парткод:	444-30000-109

Деталь:	Sensor GP2A25
Парткод:	443-32005-003

Деталь:	Side Frame F
Парткод:	033-12053-208

Деталь:	TDS-12E-5006A
Парткод:	490-50008-109

Деталь:	LINK SOLENOID
Парткод:	033-12006-005

Деталь:	SHAFT PICK-UP ROLLER
Парткод:	030-21026-106

Деталь:	SHAFT PAPER FEED
Парткод:	033-12188-103

Деталь:	Stay Transfer Unit Lower
Парткод:	033-12147-008

Деталь:	Wire Harness Assy MTPF
Парткод:	033-12254-009

Деталь:	AM50032A43F1
Парткод:	444-10001-001

Деталь:	Guide Plate Lower 4
Парткод:	030-21386-102

Деталь:	Guide Plate Lower 5
Парткод:	033-12225-106

Деталь:	Shaft Paper Sensor
Парткод:	030-21347-000

Деталь:	Spring Paper Sensor
Парткод:	030-21348-006

Деталь:	METAL 8
Парткод:	607-60002-006

Деталь:	Bearing TPF-816ZZ-5
Парткод:	609-00002-001

Деталь:	Belt 60S3M150
Парткод:	620-00004-001

Деталь:	ROLLER PAPER FEED
Парткод:	033-12229-004

Деталь:	Arm Tension F
Парткод:	033-12001-003

Деталь:	Arm Tension R
Парткод:	033-12004-002

Деталь:	Roller Tension 2
Парткод:	033-12007-001

Деталь:	Spring Roller Tension
Парткод:	033-12008-008

Деталь:	Mylar Sheet 2
Парткод:	033-12224-002

Деталь:	Junction Harness Pick-up Sensor
Парткод:	033-12255-005

Деталь:	Caster BWP-50BN
Парткод:	660-03003-001

Деталь:	Caster BWP-50N
Парткод:	660-03004-105

Деталь:	TG81A-CL-261-E83 24V
Парткод:	490-22009-302

Деталь:	Joint Elevator
Парткод:	030-21017-000

Деталь:	Shaft Elevator 2
Парткод:	030-21028-001

Деталь:	Shaft Elevator 1
Парткод:	030-21027-005

Деталь:	Gear Elevator 1
Парткод:	030-21209-006

Деталь:	Gear Elevator 2
Парткод:	030-21210-004

Деталь:	Bearing A-19-B2
Парткод:	609-00001-005

Деталь:	Spring Tray Lock
Парткод:	030-21240-000

Деталь:	Bracket Tray Lock
Парткод:	030-21238-006

Деталь:	FL-MAIN-PCB
Парткод:	033-50032-109

Деталь:	ZWS150PAF-24J
Парткод:	495-32002-000

Деталь:	Wire Harness Assy Tray
Парткод:	033-53004-203

Деталь:	Wire Harness FL2
Парткод:	033-50031-005

Деталь:	Junction Harness MTPF
Парткод:	033-53022-007

Деталь:	Wire Harness STP Motor
Парткод:	033-53018-000

Деталь:	Wire Harness Tray Interlock
Парткод:	033-53015-000

Деталь:	Wire Harness FL1
Парткод:	033-50033-008

Деталь:	Handle Latch
Парткод:	030-21361-002

Деталь:	Spring Latch Front
Парткод:	030-21365-008

Деталь:	SPRING TENSION
Парткод:	030-21364-109

Деталь:	PLATE TENSION
Парткод:	030-21363-005

Деталь:	Roller Tension 1
Парткод:	030-21362-009

Деталь:	Latch Guide Bracket Assy
Парткод:	030-21360-006

Деталь:	Shaft Latch
Парткод:	030-21031-002

Деталь:	Bottom Stay
Парткод:	030-21409-005

Деталь:	Bracket Assy Guide Lower
Парткод:	033-12059-409

Деталь:	HI - MIC5 - 27
Парткод:	490-51016-008

Деталь:	Belt 80S3M195
Парткод:	620-00013-000

Деталь:	Belt 80S3M312
Парткод:	620-00011-008

Деталь:	Belt 80S3M336
Парткод:	620-00012-004

Деталь:	HI - MIC5 - 28
Парткод:	490-51017-004

Деталь:	Pulley P27S3M39
Парткод:	611-90013-005

Деталь:	HINGE
Парткод:	030-21397-007

Деталь:	Pulley P27S3M
Парткод:	611-90015-008

Деталь:	Belt B0S3M141
Парткод:	620-00014-007

Деталь:	Cover Transfer Unit Upper
Парткод:	033-12228-008

Деталь:	CWTD3292-260
Парткод:	490-20006-004

Деталь:	Encoder Motor
Парткод:	030-21439-001

Деталь:	SENSOR GP1A73A
Парткод:	444-30000-109

Деталь:	Wire Harness Encoder
Парткод:	033-12256-001

Деталь:	Sensor EE-SX1235A-P2
Парткод:	444-30000-001

Деталь:	Sensor GP2A25
Парткод:	443-32005-003

Деталь:	Lever Tray Lock
Парткод:	030-21315-000

Деталь:	Bracket Separation
Парткод:	030-21314-004

Деталь:	CUSHION TRAY
Парткод:	030-21309-108

Деталь:	End Fence Fixed
Парткод:	033-12164-000

Деталь:	Wire Tray
Парткод:	030-21020-000

Деталь:	Wire Tray L
Парткод:	033-12187-000

Деталь:	Potentiometer Assy 2
Парткод:	030-51093-002

Деталь:	Wire Harness FG
Парткод:	030-51168-100

Деталь:	Tray Sheet
Парткод:	030-21014-000

Деталь:	SHAFT DRIVE
Парткод:	030-21073-007

Деталь:	Holder Drum Wire
Парткод:	030-21208-000

Деталь:	Cushion Tray 1
Парткод:	030-21310-009

Деталь:	Cover Potentiometer
Парткод:	030-21291-004

Деталь:	Base Plate Tray
Парткод:	030-21304-106

Деталь:	Stay Guide
Парткод:	030-21301-000

Деталь:	Bracket Potentiometer Slide
Парткод:	030-21207-003

Деталь:	Belt 40-S2M-630
Парткод:	621-00002-006

Деталь:	Stopper Table
Парткод:	030-21302-006

Деталь:	COVER BELT
Парткод:	030-21292-000

Деталь:	Holder Guide 1
Парткод:	030-21205-000

Деталь:	Guide Assy Rear
Парткод:	030-21283-001

Деталь:	Slider Lock 2
Парткод:	030-21277-001

Деталь:	Holder Guide 2
Парткод:	030-21206-007

Деталь:	Guide Assy Front
Парткод:	030-21278-008

Деталь:	Plate Lock 2
Парткод:	030-21060-002

Деталь:	Plate Lock 1
Парткод:	030-21059-004

Деталь:	Seal Lock Plate
Парткод:	030-04130-005

Деталь:	Latch Lock 2
Парткод:	030-21056-005

Деталь:	Latch Lock 1
Парткод:	030-21055-009

Деталь:	Lever Lock 2
Парткод:	030-21204-004

Деталь:	Plate Belt Fixation
Парткод:	030-21289-000

Деталь:	Pulley Potentiometer
Парткод:	030-21288-003

Деталь:	Lever Lock 1
Парткод:	030-21297-002

Деталь:	Shaft Slider
Парткод:	030-21290-008

Деталь:	Bracket Slide
Парткод:	033-12168-005

Деталь:	PLATE SENSOR
Парткод:	030-21307-008

Деталь:	TM-189-4HG
Парткод:	610-00020-000

Деталь:	Gear Damper
Парткод:	030-21265-003

Деталь:	Idler pulley
Парткод:	030-21266-000

Деталь:	Cover Base Plate
Парткод:	030-21311-005

Деталь:	Lever Ratchet
Парткод:	030-21316-007

Деталь:	Lever Ratchet 1
Парткод:	030-21317-003

Деталь:	Guide Support
Парткод:	030-21061-009

Деталь:	Pin Support
Парткод:	030-21319-006

Деталь:	SPRING LOCK
Парткод:	030-21318-000

Деталь:	E-RING 5
Парткод:	X-1604

Деталь:	Junction Wire Harness Tray
Парткод:	033-12248-106

Деталь:	Wire Harness Tray 1
Парткод:	033-12246-405

Деталь:	Wire Harness Tray 2
Парткод:	033-12247-401

Деталь:	ORIP PCB
Парткод:	033-19293-204

Деталь:	ORMC PCB
Парткод:	033-19294-006

Деталь:	MOTOR DRV PCB
Парткод:	033-19296-009

Деталь:	ORCNL PCB
Парткод:	033-19297-005

Деталь:	ORCNR PCB
Парткод:	033-19298-001

Деталь:	FUSE3
Парткод:	033-19305-008

Деталь:	DUST FAN 1
Парткод:	033-19277-004

Деталь:	DUST FAN 2A
Парткод:	033-19368-000

Деталь:	USB Cable PS7R
Парткод:	101-51035-006

Деталь:	CD-ROM1.20 PS7R
Парткод:	101-52511-308

Деталь:	Dongle PS7R(G)
Парткод:	101-52517-004

Деталь:	109P0412H358
Парткод:	490-40002-005

Деталь:	Joint PCB PS7R
Парткод:	101-50506-005

Деталь:	Mainboad PS7R
Парткод:	101-50504-002

Деталь:	Power Supply Unit PS7R
Парткод:	101-50505-009

Деталь:	Power Switch Assy PS7R
Парткод:	101-53000-005

Деталь:	DIMM168P128MB PS7R
Парткод:	101-52001-008

Деталь:	HDD Unit PS7R(G)
Парткод:	101-52513-009

Деталь:	HDD Harness PS7R
Парткод:	101-51036-002

Деталь:	Bracket HDD PS7R
Парткод:	101-11003-004

Деталь:	STAR WHEEL DPX
Парткод:	033-19249-000

Деталь:	PHOTOREFLECT B
Парткод:	033-19250-009

Деталь:	Photoreflector
Парткод:	033-19251-102

Деталь:	DPX ROLLER
Парткод:	033-19252-001

Деталь:	NIP ROLLER
Парткод:	033-19253-008

Деталь:	RESERVOIR K
Парткод:	033-19209-009

Деталь:	RESERVOIR C
Парткод:	033-19210-007

Деталь:	RESERVOIR M
Парткод:	033-19211-003

Деталь:	RESERVOIR Y
Парткод:	033-19212-107

Деталь:	OVERFLOW TANK
Парткод:	033-19214-100

Деталь:	PRESS CHAMBER
Парткод:	033-19215-009

Деталь:	PRESSURE PUMP
Парткод:	033-19216-102

Деталь:	PHOTOINTERRUPT
Парткод:	033-19217-001

Деталь:	Photoreflector
Парткод:	033-19251-102

Деталь:	MICRO SWITCH
Парткод:	033-19254-004

Деталь:	RESIST ROLLER L
Парткод:	033-19271-006

Деталь:	RESIST ROLLER U
Парткод:	033-19272-100

Деталь:	SWBACK UNIT U
Парткод:	033-19285-007

Деталь:	SWBACK UNIT L
Парткод:	033-19286-003

Деталь:	SWBACK DRV ROLL
Парткод:	033-19287-000

Деталь:	SWBACK DOOR UNIT
Парткод:	033-19288-006

Деталь:	TOP EDGE SENSOR
Парткод:	033-19289-002

Деталь:	TOP EDGE LED
Парткод:	033-19290-000

Деталь:	DOUBLE FEED LED
Парткод:	033-19299-008

Деталь:	DBL FEED SENSOR
Парткод:	033-19300-006

Деталь:	SWBACK GUIDE
Парткод:	033-19343-007

Деталь:	SWBACK ROLLER 1
Парткод:	033-19344-003

Деталь:	SWBACK HANDLE
Парткод:	033-19345-000

Деталь:	SWBACK KNOB
Парткод:	033-19346-006

Деталь:	SWBACK ROLLER 2
Парткод:	033-19347-002

Деталь:	RE3 ROLLER
Парткод:	033-19370-004

Деталь:	Rear Cover MTPF1
Парткод:	033-34003-000

Деталь:	Right Cover MTPF1
Парткод:	033-34006-009

Деталь:	Upper Cover MTPF1
Парткод:	033-34019-100

Деталь:	Left Cover MTPF1
Парткод:	033-34016-004

Деталь:	Front Cover MTPF1L
Парткод:	033-34012-009

Деталь:	Front Cover MTPF1
Парткод:	033-34009-008

Деталь:	Side Cover MTPF1
Парткод:	033-34014-001

Деталь:	Left Cover MTPF1
Парткод:	033-34007-005

Деталь:	CCD UNIT
Парткод:	033-19267-009

Деталь:	CCD SENSOR
Парткод:	033-19268-005

Деталь:	PHOTOINTERRUPT
Парткод:	033-19225-004

Деталь:	CCD AD CONV PCB
Парткод:	033-19292-003

Деталь:	SS UNIT
Парткод:	033-19363-008

Деталь:	ROLLER PICKUP
Парткод:	030-21016-100

Деталь:	LOCK RING ROLLER
Парткод:	030-21203-105

Деталь:	Spring Pick-Up Roller
Парткод:	030-21418-004

Деталь:	Stopper Upper Unit
Парткод:	033-12009-004

Деталь:	SENSOR GP1A73A
Парткод:	444-30000-109

Деталь:	Switch AM50032A431F1
Парткод:	444-10001-001

Деталь:	Cushion Rubber F 12-5404
Парткод:	030-21352-003

Деталь:	Sensor GP2A25
Парткод:	443-32005-003

Деталь:	SHAFT PICK-UP ROLLER
Парткод:	030-21026-203

Деталь:	SHAFT PAPER FEED
Парткод:	033-12188-103

Деталь:	Shaft Paper Sensor
Парткод:	030-21347-000

Деталь:	Bracket Pickup Roller
Парткод:	030-21328-005

Деталь:	Spring Paper Sensor
Парткод:	030-21348-006

Деталь:	ROLLER PAPER FEED
Парткод:	033-12229-004

Деталь:	Link JAM release 2
Парткод:	030-21396-000

Деталь:	Spring Guide Rear
Парткод:	030-21416-001

Деталь:	Spring Guide Front
Парткод:	030-21417-008

Деталь:	Link JAM release 1
Парткод:	030-21395-004

Деталь:	DDLF-1910ZZR
Парткод:	601-10195-004

Деталь:	Bracket Paper Feed Shaft
Парткод:	030-21329-001

Деталь:	Belt 60S3M150
Парткод:	620-00004-001

Деталь:	Bearing TPF-816ZZ-5
Парткод:	609-00002-001

Деталь:	Bracket Paper Sensor
Парткод:	033-12196-009

Деталь:	Stay Paper Feed
Парткод:	033-12192-003

Деталь:	Guide Plate Lower 2
Парткод:	030-21381-100

Деталь:	Junction Harness Pick-up Sensor
Парткод:	033-12255-005

Деталь:	Release Lever
Парткод:	030-21007-004

Деталь:	Lever FL Guide Plate Release
Парткод:	030-21502-005

Деталь:	Shaft Lever FLG-Plate Release
Парткод:	030-21025-002

Деталь:	COVER MOTOR
Парткод:	030-21531-005

Деталь:	Motor STP-58D5001
Парткод:	490-31008-009

Деталь:	BRACKET MOTOR
Парткод:	033-12209-305

Деталь:	Shaft Roller Tension
Парткод:	030-21074-003

Деталь:	Roller Tension Upper 2
Парткод:	030-21492-000

Деталь:	Spring Tension Upper
Парткод:	030-21498-300

Деталь:	Roller Tension Upper 1
Парткод:	030-21491-003

Деталь:	Tension Arm Front Upper
Парткод:	030-21494-002

Деталь:	Tension Arm Rear Upper
Парткод:	030-21495-009

Деталь:	Shaft Hinge Tension
Парткод:	030-21493-006

Деталь:	TDS-12E-5006A
Парткод:	490-50008-109

Деталь:	Bracket SOL
Парткод:	030-21496-005

Деталь:	Guide Plate 1
Парткод:	030-21485-208

Деталь:	COVER SOLENOID
Парткод:	030-21497-001

Деталь:	Spring Guide Plate
Парткод:	030-21500-002

Деталь:	SHAFT HOOK
Парткод:	030-21032-009

Деталь:	Guide Lock
Парткод:	030-21478-007

Деталь:	Bracket Guide Lock
Парткод:	030-21479-003

Деталь:	Plate Spring Guide
Парткод:	030-21480-001

Деталь:	Clutch HI-MIC5-11
Парткод:	490-51013-009

Деталь:	GUIDE PLATE 2
Парткод:	030-21470-103

Деталь:	Brush Roller Cleaner 2
Парткод:	030-21349-002

Деталь:	Sensor GP2A25
Парткод:	443-32005-003

Деталь:	BRACKET SENSOR
Парткод:	030-21482-004

Деталь:	TRANSFER ROLLER
Парткод:	030-21477-000

Деталь:	Stepped Screw 2.2
Парткод:	030-21003-009

Деталь:	Wire Harness STP Motor
Парткод:	033-53018-000

Деталь:	Wire Harness Roller Solenoid
Парткод:	033-53020-004

Деталь:	Wire Harness Clutch
Парткод:	033-53021-000

Деталь:	Wire Harness Paper Sensor
Парткод:	033-53019-006

Деталь:	*Bottom Cover P.-F.-T.
Парткод:	030-14102-107

Деталь:	*Paper Feed Board
Парткод:	033-12257-008

Деталь:	*Support Plate R P.-F.-T.
Парткод:	030-14113-109

Деталь:	*Support Plate F P.-F.-T.
Парткод:	030-14114-105

Деталь:	*Guide Harness
Парткод:	030-14136-001

Деталь:	*Stopper Roller
Парткод:	030-14134-106

Деталь:	*COLLAR 6x3
Парткод:	634-06030-000

Деталь:	*GEAR M0.8X18X6
Парткод:	612-11104-006

Деталь:	*Bracket P.-W. Potentiometer
Парткод:	030-14132-006

Деталь:	*P.-W. Potentiometer Assy II
Парткод:	030-51093-002

Деталь:	Junction Harness P.-F.-T.
Парткод:	030-51023-403

Деталь:	*SENSOR GP2A200LCS
Парткод:	444-33000-002

Деталь:	*Fence Cover
Парткод:	030-14123-007

Деталь:	*Guide F P.-F.-T.
Парткод:	030-14116-108

Деталь:	*Guide R P.-F-.T.
Парткод:	030-14115-101

Деталь:	*Lock Lever Paper Guide
Парткод:	030-14131-107

Деталь:	*Guide Shaft Paper Guide
Парткод:	030-14117-007

Деталь:	*GEAR M1X16X3.2
Парткод:	612-12103-003

Деталь:	*Slider F Paper Guide
Парткод:	030-14126-006

Деталь:	*Slider R Paper Guide
Парткод:	030-14124-003

Деталь:	*Lock A Paper Guide
Парткод:	030-14129-005

Деталь:	*Lock B Paper Guide
Парткод:	030-14130-003

Деталь:	*Slide Rack P.-F.-T.
Парткод:	030-14119-000

Деталь:	*Collar Slide Rack P.-F.-T.
Парткод:	030-14133-002

Деталь:	*Seal P-Feed Tray
Парткод:	030-04001-108

Деталь:	*Slide Sheet P.-F.-T.
Парткод:	030-14137-008

Деталь:	Cover F P.-F.-T. Damper
Парткод:	030-14138-101

Деталь:	Cover R P.-F.-T. Damper
Парткод:	030-14139-108

Деталь:	OWH 10-2.2NLW
Парткод:	610-10006-006

Деталь:	OWH 10-2.2NRW
Парткод:	610-10007-002

Деталь:	FLIPPER UNIT
Парткод:	033-19244-408

Деталь:	FLIPPER GATE
Парткод:	033-19245-005

Деталь:	HR ROLL
Парткод:	033-19365-000

Деталь:	FL ROLLER U
Парткод:	033-19247-008

Деталь:	FL ROLLER L
Парткод:	033-19248-004

Деталь:	COUNTER
Парткод:	033-19301-002

Деталь:	PRINT HEAD
Парткод:	033-19202-500

Деталь:	HEAD DRIVER PCB
Парткод:	033-19203-400

Деталь:	RIBBON CABLE
Парткод:	033-19204-104

Деталь:	HEAD JOINT
Парткод:	033-19205-003

Деталь:	ID UNIT
Парткод:	033-19206-000

Деталь:	Valve
Парткод:	033-19207-103

Деталь:	VALVE 2
Парткод:	033-19208-100

Деталь:	BRACKET
Парткод:	033-19348-009

Деталь:	ID UNIT MY
Парткод:	033-19328-008

Деталь:	Stripper Pad Foam
Парткод:	030-14376-002

Деталь:	Holder Separation Pad
Парткод:	030-21339-007

Деталь:	Shaft Stripper
Парткод:	033-12206-004

Деталь:	Bracket P-Release
Парткод:	033-12145-005

Деталь:	SPRING SEPARATION
Парткод:	030-21343-004

Деталь:	Spacer 1
Парткод:	033-12068-000

Деталь:	Bracket Separation
Парткод:	033-12141-000

Деталь:	Bracket Separation 2
Парткод:	033-12143-002

Деталь:	Shaft Stripper Angle
Парткод:	033-12151-005

Деталь:	Lever P-Release
Парткод:	033-12144-009

Деталь:	Spring P-Release
Парткод:	033-12146-001

Деталь:	Base Bracket Separation
Парткод:	033-12137-002

Деталь:	Gear Stripper Angle
Парткод:	033-12148-004

Деталь:	Lever P-Adjust
Парткод:	033-12149-000

Деталь:	CAM STRIPPER
Парткод:	033-12142-006

Деталь:	Shaft P-Adjust
Парткод:	033-12152-109

Деталь:	Plunger Pin
Парткод:	033-12156-007

Деталь:	Spring Plunger
Парткод:	033-12155-000

Деталь:	Base Plunger
Парткод:	033-12154-004

Деталь:	Shaft Adjuster
Парткод:	033-12153-008

Деталь:	Cover Stripper 1
Парткод:	033-12208-104

Деталь:	Cover Stripper 2
Парткод:	033-12207-108

Деталь:	Knob Angle
Парткод:	033-12051-000

Деталь:	KNOB PRESSURE
Парткод:	033-12050-004

Деталь:	Sheet Separation Adj.
Парткод:	033-12014-008

Деталь:	End Fence Fixed L
Парткод:	033-12180-005

Деталь:	Plate Lock 2L
Парткод:	033-12074-000

Деталь:	Lever Lock 1
Парткод:	030-21297-002

Деталь:	Plate Lock 1L
Парткод:	033-12174-005

Деталь:	Latch Lock 1
Парткод:	030-21055-009

Деталь:	Guide Assy L
Парткод:	033-12171-103

Деталь:	Lever Lock 2
Парткод:	030-21204-004

Деталь:	Latch Lock 2
Парткод:	030-21056-005

Деталь:	End Fence L
Парткод:	033-12167-009

Деталь:	TRANSFER UNIT
Парткод:	033-19259-006

Деталь:	Transfer belt
Парткод:	033-19260-004

Деталь:	BELT ENCODER
Парткод:	033-19261-205

Деталь:	TRANSFER MOTOR
Парткод:	033-19262-007

Деталь:	Cleaning Roller
Парткод:	033-19263-003

Деталь:	BLOWER FAN
Парткод:	033-19264-000

Деталь:	PHOTOINTERRUPT
Парткод:	033-19225-004

Деталь:	ROLLER 1
Парткод:	033-19353-002

Деталь:	ROLLER 2
Парткод:	033-19354-009

Деталь:	ROLLER 3
Парткод:	033-19355-005

Деталь:	BEARING 1
Парткод:	033-19356-001

Деталь:	BP SPRING
Парткод:	033-19357-008

Деталь:	BEARING 2
Парткод:	033-19349-005

Деталь:	Stripper Unit Thin
Парткод:	030-74002-055

Деталь:	*Cover F Stripper Pad
Парткод:	019-11832-000

Деталь:	*Base F Stripper Pad
Парткод:	019-11831-100

Деталь:	*Stripper Pad 70
Парткод:	019-11833-006

Деталь:	PAPER FEED COVER ASSY
Парткод:	030-94340-054

Деталь:	*Paper Feed Cover
Парткод:	030-14320-104

Деталь:	*Scraper Cover
Парткод:	030-14321-100

Деталь:	*Shaft Scraper Cover
Парткод:	030-14329-004

Деталь:	*Plate F Scraper Cover
Парткод:	030-14327-001

Деталь:	*Plate R Scraper Cover
Парткод:	030-14328-008

Деталь:	*Safety SW P.-F.-T. Upper
Парткод:	030-51059-106

Деталь:	SEAL P.-F.-T. DOWN
Парткод:	030-04034-006

Деталь:	Seal P.-FEED PRESSURE
Парткод:	550-21172-005

Деталь:	Scraper Assy
Парткод:	030-14312-209

Деталь:	DET. PLATE UPPER LIMIT STD.
Парткод:	030-14384-005

Деталь:	DET. PLATE UPPER LIMIT CRD
Парткод:	030-14385-001

Деталь:	SCRAPER SPRING
Парткод:	030-14373-100

Деталь:	Pickup Roller Shaft
Парткод:	030-14311-407

Деталь:	Scraper Shaft
Парткод:	030-14325-408

Деталь:	PICK-UP ROLLER
Парткод:	003-26306-100

Деталь:	COLLAR 10X34.5
Парткод:	634-10402-000

Деталь:	WASHER 18X10.4X0.4
Парткод:	638-90000-012

Деталь:	First Paper Feed Stay
Парткод:	030-14315-208

Деталь:	SUPPORT PICK UP ROLLER SHAFT
Парткод:	030-14372-007

Деталь:	Lock Ring
Парткод:	019-11812-106

Деталь:	GEAR M0.8X18X11
Парткод:	612-11101-104

Деталь:	GEAR: M0.8X34X8.5
Парткод:	612-11300-000

Деталь:	METAL F10X15/14X6 18X2
Парткод:	607-16001-000

Деталь:	Push Button SW Assy
Парткод:	021-51029-003

Деталь:	Bracket Elevator Button
Парткод:	030-14318-100

Деталь:	Support Plate B Upper Limit
Парткод:	030-14342-108

Деталь:	Upper Limit Adj. Screw
Парткод:	030-14346-006

Деталь:	BASE UPPER LIMIT ADJ. SCREW
Парткод:	030-14347-002

Деталь:	Support Plate A Upper Limit
Парткод:	030-14341-101

Деталь:	BRACKET UPPER LIMIT SENSOR
Парткод:	030-14319-009

Деталь:	SENSOR GP1A73A
Парткод:	444-30000-109

Деталь:	ARM P.-F. PRESSURE ADJ.
Парткод:	020-11813-006

Деталь:	STEPPED SCREW F8X2.3 M4X4.4
Парткод:	635-17824-005

Деталь:	P.-F. Pressure Adj. Lever
Парткод:	030-14317-006

Деталь:	SPRING A P.-F. PRESSURE ADJ.
Парткод:	020-11812-000

Деталь:	Bracket P.-F. Pressure Adj. Lever
Парткод:	020-11830-105

Деталь:	SPRING B P.-F. PRESSURE ADJ.
Парткод:	020-11811-100

Деталь:	One-way Core
Парткод:	030-14350-003

Деталь:	Paper Release Lever
Парткод:	030-14351-000

Деталь:	Spring Paper Release Lever
Парткод:	030-14353-100

Деталь:	Plate Rotation Stopper
Парткод:	030-14352-200

Деталь:	P-F Clutch
Парткод:	020-65009-105

Деталь:	W Scraper
Парткод:	030-14374-107

Деталь:	*Rubber Roller Pickup
Парткод:	035-14303-001

Деталь:	Shaft P.-F. Clutch
Парткод:	030-14386-008

Деталь:	SEAL Paper Jam
Парткод:	030-04105-000

Деталь:	GEAR M0.8x29x8.5
Парткод:	612-11200-005

Коды ошибок

M01

M02

M03

M04

S01

S02

S03

S04

S05

S06

S07

S08

S09

S10

S11

S12

S13

S14

S15

S16

S94

S95

S96

S97

S98

S99

W01

W02

W03

W04

W05

W06

W07

W08

W99

X01

X02

X03

X04

X05

X06

X07

X08

X09

X10

X11

X12

X13

X14

X15

Y01

Y02

Z01

Z02

Z03

Z04

Z05

Z06

Z07

Z08

Z09

Z10

Z11

Z12

Z13

Z14

Error code:	M01
Description:	Maintenance call
Causes:	The print count has reached the scheduled maintenance value. 030 M01 Maintenance call Maintenance count reached the maximum at machine ON, all-reset, or at end of print job. * The maintenance count is set by the Test Mode.
Remedy:	Run Test mode [Clear error] (5.12.2). Or set the scheduled maintenance value to [0]. Or clear the scheduled maintenance value.

Error code:	M02
Description:	Waste ink tank Near full
Causes:	The waste ink tank needs to be replaced soon. 324 M02 Waste ink tank near-full The waste ink tank is almost full.
Remedy:	Replace the waste ink tank. (This error is cleared when the absence of a waste ink tank is detected.) Or the waste ink tank is full (automatic clear).

Error code:	M03
Description:	Operation in temporary registration status
Causes:	The machine is currently operating under temporary registration. 051 M03 Operation in temporary registration status The main unit is currently operating under temporary registration.
Remedy:	Run Test mode [Conformity check] (5.13.1) while temporary registration status is in effect. It will clear automatically when the temporary registration period expires.

Error code:	M04
Description:	Incorrect ink version number
Causes:	No discharging parameter on the mounted ink cartridge. 343 M04 Incorrect ink version No discharging parameter on the mounted ink cartridge.
Remedy:	Upgrade the machine program version.

Error code:	S01
Description:	BP motor lock
Causes:	The main transport system cannot be controlled appropriately. 202 S01 Transfer belt motor error An alarm signal from the DC servo motor was detected (detection of overcurrent during operations). 203 S01 Transfer belt motion speed error The clock frequency of the belt motor shaft encoder falls outside the specified range. 204 S01 Belt encoder error The frequency input from the belt encoder is below the specified value.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S02
Description:	Elevator motor lock
Causes:	The elevator cannot be controlled appropriately. 104 S02 Elevator motor timeout The upper limit sensor fails to activate when the elevator rising operation is activated within the specified interval. 119 S02 Elevator motor timeout The lower limit sensor fails to activate during a standard paper feed tray lowering operation within the specified interval.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S03
Description:	Belt platen lock
Causes:	The belt platen elevation mechanism cannot be set properly. 200 S03 Transfer belt motor timeout The motor shaft encoder of the transfer belt motor does not attain the specified pulse count within the specified time. The required movement does not complete even when the transfer belt motor operates for the specified interval. 201 S03 Transfer belt unit sensor error The three sensors that determine the position of the belt platen produced an abnormal detection result. 231 S03 Belt platen operation error The upper limit position sensor fails to activate when the belt platen rises. 240 S03 Belt platen operation error The upper limit position sensor fails to deactivate when the belt platen lowers. 241 S03 Belt platen operation error The lower limit position sensor fails to activate when the belt platen lowers. 242 S03 Belt platen operation error The lower limit position sensor fails to deactivate when the belt platen rises. 243 S03 Belt platen operation error The vacuum positioning sensor fails to activate when the belt platen operates. 244 S03 Belt platen operation error The vacuum positioning sensor fails to deactivate when the belt platen operates.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S04
Description:	Head maintenance error
Causes:	Head maintenance cannot be controlled appropriately. Including waste ink tank full condition. 300 S04 Ink pan motor timeout The right or left sensor fails to activate within the specified interval. 301 S04 Ink pan sensor error The right and left sensors activate at the same time. 302 S04 Cleaning motor timeout The detection plate does not reach the suction nozzle HP sensor even when the motor operates for the specified interval to move the cleaning motor to the retraction position on the front side. Or the suction nozzle HP sensor fails to deactivate when it moves from the HP. 303 S04 Suction chamber full The suction chamber sensor is turned ON. 300 S04 Ink pan motor timeout The right or left sensor fails to activate within the specified interval. 301 S04 Ink pan sensor error The right and left sensors activate at the same time. 302 S04 Cleaning motor timeout The detection plate does not reach the suction nozzle HP sensor even when the motor operates for the specified interval to move the cleaning motor to the retraction position on the front side. Or the suction nozzle HP sensor fails to deactivate when it moves from the HP. 303 S04 Suction chamber full The suction chamber sensor is turned ON. 305 S04 Suction pump rotation speed error The rotation speed of the suction pump falls outside the specified range (checked by the encoder clock frequency for the specified time). 307 S04 Overflow tank full Ink is detected by the overflow sensor. 321 S04 Pressure pump motor timeout The logic of the pressure pump sensor (detection at motor 180-degree intervals) does not change even when the pressure pump motor is driven for a certain time period. 344 S04 Cleaning motor timeout 2 HP sensor does not go ON even after the motor rotates for the specific time period to move the cleaning motor to the front retracting position. 345 S04 Error on the Cleaning Motor When the cleaning motor rotated, the pulse count was below the parameter after completion of moving. 346 S04 Cleaning motor timeout 3 HP sensor does not go OFF even after the motor rotates for the specific time period to move the cleaning motor to the rear.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S05
Description:	Head thermistor error
Causes:	Head temperature control is malfunctioning. 311 S05 Disconnection in head thermistor The head temperature could not be measured correctly. When the reading of the thermistor is -86.9 °C * Head identification information (K1 - Y6) is added after the error point. 312 S05 Head abnormally hot The head temperature exceeded 80 °C. When the reading of the thermistor is 80.0 °C * Head identification information (K1 - Y6) is added after the error point. 313 S05 Head cooling timeout The temperature remained above 45 °C for 10 minutes. When the monitored head temperature remains 45 °C or more for 10 minutes * Head identification information (K1 - Y6) is added after the error point.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S06
Description:	Ink heating error
Causes:	Ink heating control is malfunctioning. 314 S06 Ink heating timeout When the temperature of ink in the distributor meets the following conditions after being heated for a set time: 1) & either 2), 3) 4), 5), 6) or 7) 1) The temperature is less than 15 °C. 2) It takes more than 360 seconds to raise the temperature by 1 °C after the heater has been powered on. 3) It takes more than 600 seconds to raise the temperature by 4 °C after the heater has been powered on. 4) It takes more than 750 seconds to raise the temperature by 7 °C after the heater has been powered on. 5) It takes more than 900 seconds to raise the temperature by 10 °C after the heater has been powered on. 6) It takes more than 1,320 seconds to raise the temperature by 13 °C after the heater has been powered on. 7) A temperature of less than 15 °C holds for more than 1,800 seconds. * Head identification information (K, C, M, Y) is added after the error point.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Деталь:	CONTROL PANEL E
Парткод:	033-19366-007

Деталь:	BU LEVER2
Парткод:	033-19367-100

Деталь:	LATCH
Парткод:	033-19335-004

Деталь:	INTERLOCK SW1
Парткод:	033-19337-007

Error code:	S07
Description:	Ink cooling error
Causes:	Ink cooling control is malfunctioning. 319 S07 Ink cooling timeout The temperature of ink being distributed remains 40 °C for five minutes. * Ink identification information (K, C, M, Y) is added after the error point.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S08
Description:	Controller (PS7R) error
Causes:	Communication with the controller (PS7R) cannot be achieved. Or an error notification has been received from the controller (PS7R). 320 S98 Head voltage error * Head identification information (K1 - Y6) is added after the error point. 511 S08 PS7R controller system error. PS7R controller system is in abnormal condition. 512 S08 PS7R controller HDD access error. Unable to access to the PS7R controller HDD.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S09
Description:	Exit option error
Causes:	A service error is generated in the exit option. 500 S09 Auto fence timeout (fence check) [Movement complete] was not received during the fence moving operation within the specified interval. 509 S09 Paper guide sensor error The paper guide HP sensor and limit sensor have activated simultaneously. 510 S09 Paper stopper sensor error The paper stopper HP sensor and limit sensor have activated simultaneously.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S10
Description:	Multi-tray paper feed error
Causes:	A service error is generated in the multi-tray paper feed. 400 S10 FL transfer motor lock (Detailed No. 1: timeout) There was no input interrupt from the FL transfer motor FG sensor during FL transfer motor operation, even after the specified time elapsed. 402 S10 Feed tray 1 elevator motor lock (Detailed No. 1: timeout) The FL feed tray 1 upper limit sensor fails to activate after the FL feed tray 1 elevator motor turns ON, even after the specified time elapses. * This error can be cleared by opening feed tray 1. 403 S10 Feed tray 1 elevator motor lock (Detailed No. 2: overcurrent) An overcurrent was detected in the FL feed tray 1 elevator motor. * This error can be cleared by opening feed tray 1. 404 S10 Feed tray 2 elevator motor lock (Detailed No. 1: timeout) The FL feed tray 2 upper limit sensor fails to activate after the FL feed tray 2 elevator motor turns ON even after the specified time elapses. * This error can be cleared by opening feed tray 2. 405 S10 Feed tray 2 elevator motor lock (Detailed No. 2: overcurrent) Overcurrent was detected in the FL feed tray 2 elevator motor. * This error can be cleared by opening feed tray 2. 406 S10 Feed tray 1 paper width adjustment parameter error The correction value for the feed tray 1 paper width VR falls outside the specified range. * This error can be cleared by opening the feed tray or opening the cover of the vertical transfer unit. 407 S10 Feed tray 2 paper width adjustment parameter error The correction value for the feed tray 2 paper width VR falls outside the specified range. * This error can be cleared by opening the feed tray or opening the cover of the vertical transfer unit. 408 S10 Multi-tray paper feed multiple feed sensor light emitting intensity error The multiple feed sensor light emitting intensity falls outside the specified range. * This error can be cleared by opening the feed tray or opening the cover of the vertical transfer unit. 409 S10 Multi-tray paper feed EEPROM error Data could not be written correctly to the EEPROM. Or an EEPROM checksum error occurred. * This error can be cleared by opening the feed tray or opening the cover of the vertical transfer unit.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S11
Description:	Paper feed motor lock
Causes:	The paper feed motor cannot be controlled appropriately.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S12
Description:	Exit motor lock
Causes:	The exit motor cannot be controlled appropriately. 100 S12 Exit motor encoder error The encoder frequency input from the exit motor unit deviates from the theoretical value. 102 S12 Wing motor timeout The wings do not reach the HP when they are operated for a period of time corresponding to the distance of travel. 103 S12 Wing motor timeout The wing HP sensor does not detect the movement of the wings from the HP when they are operated for the specified interval.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S13
Description:	Blower fan lock
Causes:	The blower fans cannot be controlled appropriately.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S14
Description:	Waste ink tank error
Causes:	The waste ink tank is full. 323 S14 (Y02) Water ink tank full The waste ink tank is detected as full.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S15
Description:	Ink distributor ink level down
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S16
Description:	Auto fence error
Causes:	Error exists on the paper receiving tray auto-fence.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Riso HC5000

Модули

Детали

Коды ошибок

Описание

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Error code:	S94
Description:	Download error (loader)
Causes:	Communication error or data error during downloading.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S95
Description:	Download error
Causes:	Communication error or data error during downloading. 045 S95 Download error (HC Control PCB detection) An error was detected on the HC Control PCB side during a download. 046 S95 Download error (IP PCB detection) An error was detected on the IP PCB side during a download. 047 S95 Download error (MC PCB detection) An error was detected on the MC PCB side during a download. 054 S95 Error in the downloaded data. Error in the downloading data received.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S96
Description:	PCB or hardware disconnection
Causes:	The PCB is not connected. 001 S96 Power supply remote signal not connected The control signal cable for the ON/OFF control of the 24/38-VDC output is disconnected. The signal wire grounded inside the power supply unit has been pulled up by the IP PCB to detect the level. 008 S96 Control panel not connected The absence of the control panel unit to be connected to the MC PCB is detected. Since this configuration lacks this panel, this error indication will not be issued under normal operating circumstances. 009 S96 Print counter not connected The absence of a print counter is detected. 011 S96 CIS PCB not connected The connection of the CIS PCB cannot be confirmed. 013 S96 K head driver PCB not connected The connection of the K color head driver PCB cannot be confirmed with the connection detection signal. 014 S96 C head driver PCB not connected The connection of the C color head driver PCB cannot be confirmed with the connection detection signal. 015 S96 M head driver PCB not connected The connection of the M color head driver PCB cannot be confirmed with the connection detection signal. 016 S96 Y head driver PCB not connected The connection of the Y color head driver PCB cannot be confirmed with the connection detection signal. 028 S96 ORCNL PCB on machine left side not connected The connection of the ORCNL PCB on the machine left side cannot be confirmed. 029 S96 HC Control PCB timeout The Busy signal on the HC control PCB will not be deactivated upon the start of communication from the MC PCB. 042 S96 R/W PCB failure 3 Connection signal timeout (The PCB is not connected.) 043 S96 HC Control PCB not connected The connection of the HC Control PCB cannot be confirmed. (The HC Control PCB READY signal cannot be confirmed when the IP PCB is powered on.) 113 S96 Pickup clutch not connected The connection of the pickup clutch cannot be confirmed. 114 S96 Registration clutch not connected The connection of the registration clutch cannot be confirmed. 115 S96 Registration brake not connected The connection of the registration brake cannot be confirmed. 121 S96 Dust fan 1 not connected Connection of dust fan 1 cannot be confirmed. 122 S96 Dust fan 2 not connected Connection of dust fan 2 cannot be confirmed. 205 S96 Blower fan 1 disconnected/not connected The connector for blower fan 1 is disconnected, or there is a break in the winding. 206 S96 Blower fan 2 disconnected/not connected The connector for blower fan 2 is disconnected, or there is a break in the winding. 207 S96 Blower fan 3 disconnected/not connected The connector for blower fan 3 is disconnected, or there is a break in the winding. 208 S96 Blower fan 4 disconnected/not connected The connector for blower fan 4 is disconnected, or there is a break in the winding. 232 S96 Belt platen elevator clutch not connected The connection of the belt platen elevator clutch cannot be confirmed. 233 S96 Gate solenoid not connected The connection of the gate solenoid cannot be confirmed. 234 S96 Duplex transport not connected The connection of the duplex clutch cannot be confirmed. 235 S96 Re-feed pickup clutch not connected The connection of the re-feed pickup clutch cannot be confirmed. 236 S96 Re-feed brake not connected The connection of the re-feed brake cannot be confirmed. 239 S96 Switchback clutch not connected The connection of the switchback clutch cannot be confirmed. 304 S96 Suction chamber sensor not connected 308 S96 Overflow tank not connected The connection of the overflow sensor cannot be confirmed. 309 S96 Cooling fan 1 not connected 310 S96 Cooling fan 2 not connected 316 S96 Reservoir not connected * Ink identification information (K, C, M, Y) is added after the error point. 317 S96 ID unit air open valve not connected * Ink identification information (K, C, M, Y) is added after the error point. 318 S96 Distributor unit not connected * Unit identification information (KC, MY) is added after the error point. 322 S96 (Z12) Waste ink tank not installed The waste ink tank is not installed.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S97
Description:	Power supply error
Causes:	There is a problem with the power supply. 003 S97 38-VDC power supply voltage error A voltage drop is detected when a voltage drop is sensed by the IP PCB based on the signal resulting from dividing the 38-VDC resistance inside the power supply unit. The detection level is approximately 18 VDC. Voltage polling is conducted at 100-ms intervals by the IP-CPU. An error is detected when a voltage drop is sensed 10 times in succession (approx. 1 sec). No detection is performed when the interlock SW is open. 004 S97 24-VDC power supply voltage error A voltage drop is detected when a voltage drop is sensed by the IP PCB based on the signal resulting from dividing the 24-VDC resistance inside the power supply unit. The detection level is approximately 11 VDC. Voltage polling is conducted at 100-ms intervals by the IP-CPU. An error is detected when a voltage drop is sensed 10 times in succession (approx. 1 sec). No detection is performed when the interlock SW is open. 006 S97 3.3-VDC power supply voltage error A voltage drop is detected when a voltage drop is sensed in the 3.3-VDC power supply on the MIP side of the IP PCB. Voltage polling is conducted at 100-ms intervals by the IP-CPU. An error is detected when a voltage drop is sensed 10 times in succession (approx. 1 sec). 007 S97 1.8-VDC power supply voltage error A voltage drop is detected when a voltage drop is sensed in the 1.8-VDC power supply on the MIP side of the IP PCB. Voltage polling is conducted at 100-ms intervals by the IP-CPU. An error is detected when a voltage drop is sensed 10 times in succession (approx. 1 sec).
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S98
Description:	Hardware error
Causes:	The hardware cannot be controlled appropriately. 012 S98 IP PCB not connected (communication error) The IP PCB is not connected. Since the MC PCB receives its power from the IP PCB, this error indication will not be issued under normal operating circumstances. 017 S98 Control panel LCD error An error was detected in the panel LCD drive chip. Since the LCD driver will not operate when this error occurs, this error indication will not be issued under normal operating circumstances. 018 S98 K head driver PCB error Head Driver PCB error is indicated when: A head driver PCB configuration error has occurred. A failure by the MIP to respond to a data request from the head driver PCB has been detected. A communication error between the head driver PCB and IP has been detected. A 38-V voltage error in the head driver PCB has been detected. 019 S98 C head driver PCB error Same as when detecting a K head driver PCB error. 020 S98 M head driver PCB error Same as when detecting a K head driver PCB error. 021 S98 Y head driver PCB error Same as when detecting a K head driver PCB error. 022 S98 MC PCB FPGA program error Improper operation of the FPGA program on the MC PCB was detected. 023 S98 IP PCB MIP program error. MIP configuration on the main PCB failed. 024 S98 IP PCB SPLD program error SPLD configuration on the main PCB failed. 040 S98 R/W PCB failure 1 Initial communication with the R/W PCB failed. 041 S98 R/W PCB failure 2 Run signal timeout 052 S98 Date/time setting error The date/time is not set correctly. The clock is set with a date predating the PLIP firmware release date. Or the clock is set with a date postdating the year 2030. 058 S98 Error on NVRAM. Error with NVRAM on the machine. 101 S98 Multiple feed sensor error A change in light intensity does not change the amount of light received at power ON or during initialization to reset a multiple feed error. * This error can be cleared by the panel setting [Multiple feed detection OFF]. 245 S98 Error in Image Adjustment Paper size used in Image Adjustment is out of the range. Or the scanned data by the CCD is wrong (out of the range).
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S99
Description:	Software error
Causes:	For debugging 025 S99 For debugging: A DC startup report does not arrive from the IP-CPU within the specified time. 026 S99 For debugging: The IP-CPU does not respond to the sensor monitor demand from the MC-CPU. 027 S99 For debugging: The IP-CPU does not respond to the SQR from the MC-CPU. 031 S99 Multi-tray paper feed communication error 1 Multi-tray paper feed power line error 032 S99 Multi-tray paper feed timeout The machine status command transmitted from the paper feed device on the base was outside the specified range (phase error). Or the [Preparation complete] status command was not received within the specified interval after receiving the [Preparing] status command. 033 S99 Multi-tray paper feed communication error 1 The machine status command was not received from the paper feed device on the base within the specified interval (when the papaer feed device on the base does not respond). 034 S99 Multi-tray paper feed communication error 2 Base paper feed initialization information completion command was not received within the specified time of 1 second after the base paper feed initialization command was issued. 035 S99 Multi-tray paper feed communication error 3 Status information could not be transmitted during communications with the auto fence function within the specified interval. 036 S99 Auto fence communication error A Test mode status command was not received before the elapse of the specified interval after the transmission of the Test mode execution command. 037 S99 Multi-tray paper feed communication error 2 Multi-tray paper feed communication transmission error 038 S99 Multi-tray paper feed communication error 3 Multi-tray paper feed communication reception break error 039 S99 Multi-tray paper feed communication error 4 Multi-tray paper feed communication transmission buffer error 044 S99 HC Control PCB communication error (timeout error) A command from the HC Control PCB was not received during the HC Control-MC communication within the specified interval. 048 S99 FRAM checksum error FRAM checksum error of the HC Control PCB 049 S99 FRAM read verify error The data does not match data read from the FRAM of the HC Control PCB. 050 S99 FRAM write verify error The data does not match data written to the FRAM of the HC Control PCB. 053 S99 FRAM access error The FRAM of the HC Control PCB could not be accessed normally. 055 S99 Machine information software error. Error detected by the HC Control PCB while processing the machine type data. 056 S99 Machine software error (debug error) 057 S99 Communication error between IP-MC PCBs. Error between IP-MC PCBs during communication. 340 S99 Ink tag software error (For debugging) * Ink identification information (K, C, M, Y) is added after the error point.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	W01
Description:	Paper change
Causes:	No paper (When any tray is empty) 116 W01 No paper All feed trays are empty.
Remedy:	Set paper in one of the feed trays.

Error code:	W02
Description:	No paper (Standard paper feed tray)
Causes:	The standard paper feed tray is empty when paper feed is selected. 110 W02 No paper in standard paper feed tray The standard paper feed tray is empty when it is selected as the feed tray.
Remedy:	Press the Cancel key on the panel. Or load the applicable feed tray with paper. Or select another feed tray (Menu 6). Or clear the print job (Menu 7).

Error code:	W03
Description:	No paper (Feed tray 1)
Causes:	The feed tray 1 is empty when paper feed is selected. 433 W03 Feed tray 1 no paper Although selected as the current feed tray, feed tray 1 is currently empty.
Remedy:	Press the Cancel key on the panel. Or load the applicable feed tray with paper. Or select another feed tray (Menu 6). Or clear the print job (Menu 7).

Error code:	W04
Description:	No paper (Feed tray 2)
Causes:	The feed tray 2 is empty when paper feed is selected. 434 W04 Feed tray 2 no paper Although selected as the current feed tray, feed tray 2 is currently empty.
Remedy:	Press the Cancel key on the panel. Or load the applicable feed tray with paper. Or select another feed tray (Menu 6). Or clear the print job (Menu 7).