Riso MZ770A
Рейтинг
Модули
Master Making Area(3)
Drum Rail (2)
Scanner Type 1 (2) (For MZ7 Series)
Exterior Cover Area
Master Making Area(4)
Separator Area
Drive Mechanism Area(1)
Drum Area(1)
Master Removal (2) Paper Feed Side
Master Making Area(1)
Drive Mechanism Area (3)
Drum Area(3)
Master Removal (1) Paper Receive Side
Electrical Component Area(2)
Scanner Type 3 (1) (For MZ7/9 Series)
Roller System Area
Scanner Type 3 (2) (For MZ7/9 Series)
Main Body
Suction Area
Stage Cover Area
Electrical Component Area(1) Panel
Paper Receiving Tray Area
Master Making Area(2)
Mid Feed Area
Scanner Type 1 (1) (For MZ7 Series)
Scanner Type 2 (1) (For MZ7 Series)
Electrical Component Area(4)
Scanner Type2 (2) (For MZ7 Series)
Master Removal (2) Paper Receive Side
Master Disposal (Paper Receive Side)
Master Disposal (Paper Feed Side)
Drum Area(2) revised
Drum Area(4)
Elevator Area
1ST PAPER FEED
Master Removal (1) Paper Feed Side
Paper Feed Tray
Drum Rail (1)
Electrical Component Area(3)
Drive Mechanism Area (2)
Детали Mid Feed Area
| Деталь: | *Side Plate M-M Unit R |
| Парткод: | 024-28108-003 |
| Деталь: | *Side Plate M-M Unit F |
| Парткод: | 024-28109-107 |
| Деталь: | *Master Roll Holder A3 Assy (41-51) 1 |
| Парткод: | 024-75083-051 |
| Деталь: | *Bracket Slide Shaft F 1 |
| Парткод: | 024-28044-005 |
| Деталь: | *Boss Slide Gear 4 |
| Парткод: | 024-28152-002 |
| Деталь: | *Gear M1X30X6 2 |
| Парткод: | 612-00007-009 |
| Деталь: | *Gear M0.8X60X7 1 |
| Парткод: | 612-10203-000 |
| Деталь: | *Gear Mx0.5X89+M0.8X26 1 |
| Парткод: | 612-80030-006 |
| Деталь: | *Shaft Clamp A 1 |
| Парткод: | 024-26002-003 |
| Деталь: | *Shaft M-M Unit 1 |
| Парткод: | 024-28107-007 |
| Деталь: | *Metal F12X16/14.8X8 20X2 2 |
| Парткод: | 607-17001-004 |
| Деталь: | *Hook Shaft M.-M Unit 2 |
| Парткод: | 023-28148-008 |
| Деталь: | *Stopper Rear M.-M Unit 1 |
| Парткод: | 023-28247-103 |
| Деталь: | *Stay M-M Unit Upper 1 |
| Парткод: | 024-28031-000 |
| Деталь: | *Stay Stocker 1 |
| Парткод: | 024-28111-004 |
| Деталь: | *De-Electricity Brush A3 1 |
| Парткод: | 023-28410-004 |
| Деталь: | *Sensor (Send) KH0854-00 1 |
| Парткод: | 444-42029-005 |
| Деталь: | *Lower Bracket Master End Sensor 1 |
| Парткод: | 023-28417-009 |
| Деталь: | *Wire Harness M-M Rear |
| Парткод: | 024-28504-006 |
| Деталь: | *M Set Guide Plate B A3 |
| Парткод: | 023-28114-103 |
| Деталь: | *Spring B Front M Set Guide Plate 1 |
| Парткод: | 023-28115-100 |
| Деталь: | *Spring B Rear M Set Guide Plate 1 |
| Парткод: | 023-28228-109 |
| Деталь: | *Shaft M Set Guide Plate 1 |
| Парткод: | 023-28036-102 |
| Деталь: | *Stay M-M Unit Bottom 1 |
| Парткод: | 024-28110-008 |
| Деталь: | *Stay M-M Unit Rear 1 |
| Парткод: | 024-28039-001 |
| Деталь: | *Master Guide 1 |
| Парткод: | 024-28009-005 |
| Деталь: | *Master Guide Roller 2 |
| Парткод: | 023-28210-005 |
| Деталь: | *Seal M-M Unit Access Cover 1 |
| Парткод: | 024-28205-009 |
| Деталь: | *M-M Inner Cover F 1 |
| Парткод: | 024-28010-003 |
| Деталь: | *Seal Setting Master Pic. 1 |
| Парткод: | 024-28207-001 |
| Деталь: | *Motor PM42L-048-ZVS6 1 |
| Парткод: | 490-33015-002 |
| Деталь: | *D-Plate Slide Sensor 1 |
| Парткод: | 024-28155-001 |
| Деталь: | *Bracket Stopper M Set Guide Plate 1 |
| Парткод: | 023-28396-001 |
| Деталь: | *Shaft Stopper M Set Guide Plate 1 |
| Парткод: | 023-28397-008 |
| Деталь: | *Stopper Spring M Set Guide Plate |
| Парткод: | 023-28399-000 |
| Деталь: | *Stopper M Set Guide Plate |
| Парткод: | 023-28398-004 |
| Деталь: | *Bracket Slide Shaft R 1 |
| Парткод: | 024-28043-009 |
| Деталь: | *Shaft Open/Close Stopper 1 |
| Парткод: | 024-28073-005 |
| Деталь: | *Spring Open/Close Stopper 1 |
| Парткод: | 024-28042-002 |
| Деталь: | *Open/Close Stopper 1 |
| Парткод: | 024-28040-000 |
| Деталь: | *M-M Inner Cover R 1 |
| Парткод: | 024-28011-000 |
| Деталь: | **Lever Master roll Holder 1 |
| Парткод: | 023-28133-000 |
| Деталь: | **Lever Spring Master Roll Holder 1 |
| Парткод: | 023-28135-003 |
| Деталь: | **Master Holder Base A3 1 |
| Парткод: | 023-28371-009 |
| Деталь: | **Hook Master Roll Holder 1 |
| Парткод: | 023-28134-007 |
| Деталь: | **Lever Shaft Master Roll Holder 1 |
| Парткод: | 023-28132-004 |
| Деталь: | **Reinforcement Plate Master Holder Base 1 |
| Парткод: | 023-28394-009 |
| Деталь: | **Guide Spring Master Holder 1 |
| Парткод: | 023-28136-000 |
| Деталь: | **Damper Case Master Holder |
| Парткод: | 023-28372-005 |
| Деталь: | **Master Flange Rear |
| Парткод: | 023-28007-005 |
| Деталь: | **Guide Flange Master Holder 1 |
| Парткод: | 019-15255-007 |
| Деталь: | **Damper 2G50-C-10HG 1 |
| Парткод: | 610-00022-003 |
| Деталь: | *Cutter Cover 1 |
| Парткод: | 024-28119-005 |
| Деталь: | *Sensor ON-171-A8 1 |
| Парткод: | 444-33003-001 |
| Деталь: | *Bracket Set sensor M.-M Upper 1 |
| Парткод: | 023-28214-108 |
| Деталь: | *Sensor LG-248Nl1 1 |
| Парткод: | 444-30008-002 |
| Деталь: | *Wire Harness M-M Mid 1 |
| Парткод: | 024-28506-009 |
| Деталь: | *Cover Master Pos. Sensor 1 |
| Парткод: | 023-28053-104 |
| Деталь: | *Fan D04R-24TH15EX |
| Парткод: | 490-40004-008 |
| Деталь: | *Master Set Guide Bar |
| Парткод: | 023-28317-004 |
| Деталь: | *RF-Tag Reader Master 1 |
| Парткод: | 444-59006-009 |
| Деталь: | *Master Flange Front 1 |
| Парткод: | 023-28006-106 |
| Деталь: | *PCB Stay 1 |
| Парткод: | 024-28113-104 |
| Деталь: | *RFRW-PCB 3Ch 1 |
| Парткод: | 045-50025-308 |
| Деталь: | *Wire Harness M-M Front 1 |
| Парткод: | 024-28508-109 |
| Деталь: | *Wire Harness Master RF 1 |
| Парткод: | 024-28509-008 |
| Деталь: | *Make-Master PCB 1 |
| Парткод: | 024-28511-100 |
| Деталь: | *Wire Harness MM Unit FCC |
| Парткод: | 024-53001-000 |
| Деталь: | Horizontal Motor Unit Assy (17-48) |
| Парткод: | 024-75091-054 |
| Деталь: | Slide Rail |
| Парткод: | 024-17063-008 |
| Деталь: | Drum Support Left Rail |
| Парткод: | 023-17062-101 |
| Деталь: | Drum Support Right Rail |
| Парткод: | 023-17061-105 |
| Деталь: | Pre-Pressure Spring Left |
| Парткод: | 023-17140-102 |
| Деталь: | Pre-Pressure Spring Rig |
| Парткод: | 023-17139-104 |
| Деталь: | STAY RAIL |
| Парткод: | 024-17060-009 |
| Деталь: | Guide Front Frame R |
| Парткод: | 024-17203-004 |
| Деталь: | Guide Front Frame L |
| Парткод: | 024-17204-000 |
| Деталь: | Seal Drum Set Position |
| Парткод: | 023-17302-005 |
| Деталь: | Guide Front Frame Cover |
| Парткод: | 024-17400-004 |
| Деталь: | Bracket B-Release Base |
| Парткод: | 024-17278-101 |
| Деталь: | Base B Position Release |
| Парткод: | 024-17166-109 |
| Деталь: | Slide Shaft R Assy |
| Парткод: | 024-17500-106 |
| Деталь: | Slide Shaft L Assy |
| Парткод: | 024-17518-005 |
| Деталь: | Plate Slide Shaft ADJ |
| Парткод: | 024-17520-107 |
| Деталь: | Blind Plate |
| Парткод: | 024-17523-009 |
| Деталь: | *Base Horizontal Motor |
| Парткод: | 024-18002-002 |
| Деталь: | *Gear M0.8X65X6 |
| Парткод: | 612-10037-003 |
| Деталь: | *Gear M0.8X41X6 |
| Парткод: | 612-10038-000 |
| Деталь: | *Washer |
| Парткод: | 024-18011-001 |
| Деталь: | *Gear M0.8X16+M0.8X36 |
| Парткод: | 612-81304-002 |
| Деталь: | *Motor X03-42D4-050 |
| Парткод: | 490-31011-000 |
| Деталь: | *Base Horizontal Movement |
| Парткод: | 024-18001-006 |
| Деталь: | *Catch Horizontal Guide Shaft |
| Парткод: | 024-18030-006 |
| Деталь: | *Guide H-Pressure Spring |
| Парткод: | 024-18010-005 |
| Деталь: | *Sub Movable Plate |
| Парткод: | 024-17524-005 |
| Деталь: | *Edging Saddle TSB-1909L |
| Парткод: | 665-04068-006 |
| Деталь: | *Bracket Horizontal Sensor |
| Парткод: | 024-18013-101 |
| Деталь: | *Plate Horizontal Sensor Cover |
| Парткод: | 024-18031-002 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | *Wire Harness D-Drawer H |
| Парткод: | 024-53030-108 |
| Деталь: | *Wire Harness D-Drawer H U |
| Парткод: | 024-53031-007 |
| Деталь: | *Slide Guide Horizontal |
| Парткод: | 024-18017-000 |
| Деталь: | *Spring Horizontal |
| Парткод: | 024-18009-007 |
| Деталь: | *Horizontal Screw |
| Парткод: | 024-18008-000 |
| Деталь: | *Catch Horizontal Screw |
| Парткод: | 024-18029-008 |
| Деталь: | *Movable Plate |
| Парткод: | 024-18014-000 |
| Деталь: | *SW Base Plate |
| Парткод: | 024-18022-003 |
| Деталь: | *Spring Safety SW |
| Парткод: | 024-18028-001 |
| Деталь: | *SW Plate |
| Парткод: | 024-18027-005 |
| Деталь: | *D-Lock Lever |
| Парткод: | 024-18020-000 |
| Деталь: | *Spring D-Lock |
| Парткод: | 024-18021-007 |
| Деталь: | *Shaft D-Lock |
| Парткод: | 024-18019-002 |
| Деталь: | *Shaft Horizontal Guide |
| Парткод: | 024-18012-008 |
| Деталь: | *Link Plate Horizontal |
| Парткод: | 024-18015-007 |
| Деталь: | *Bracket D-Lock Sensor |
| Парткод: | 024-17164-106 |
| Деталь: | *Solenoid TDS-08A-4104 |
| Парткод: | 490-50010-006 |
| Деталь: | *Detection Plate |
| Парткод: | 024-17525-001 |
| Деталь: | Solenoid cover |
| Парткод: | 024-17527-101 |
| Деталь: | Wire Harness FL Motor |
| Парткод: | 024-53036-009 |
| Деталь: | Wire Harness Drum Drawer Junction |
| Парткод: | 024-53026-003 |
| Деталь: | Wire Harness F-Safety SW |
| Парткод: | 024-53034-006 |
| Деталь: | *Plastic Bearing Gsf-081605 |
| Парткод: | 021-17511-009 |
| Деталь: | *Pulley Ply-S1.5M-90-30 |
| Парткод: | 021-17575-007 |
| Деталь: | *Bracket K-BKT-M Scanner |
| Парткод: | 021-17505-106 |
| Деталь: | *Bracket FB Pulse Motor BKT-MOT |
| Парткод: | 021-17541-005 |
| Деталь: | *Motor Kh42Jm2B154 |
| Парткод: | 021-53201-008 |
| Деталь: | *Wire Harness FB Pulse Motor |
| Парткод: | 023-53017-007 |
| Деталь: | *Frame Assy-Frame-Lower |
| Парткод: | 021-17501-003 |
| Деталь: | *Frame Carriage 1 Frm-Cr1 |
| Парткод: | 021-17554-000 |
| Деталь: | *Inverter Pws-Pxz170E4-B |
| Парткод: | 021-50536-009 |
| Деталь: | *Cover Inverter CVR-INV |
| Парткод: | 021-17558-005 |
| Деталь: | *Mylar Inverter Mlr-Inv |
| Парткод: | 021-17518-003 |
| Деталь: | *Mirror Carriage 1 Mir-1 |
| Парткод: | 021-17509-004 |
| Деталь: | *Adj. Bracket Rear BKT-ADJ-CR1 |
| Парткод: | 021-17555-006 |
| Деталь: | *Plate Spring Mirror 1 Spr-Mir-1 |
| Парткод: | 021-17528-009 |
| Деталь: | *Sponge Mirror 1 Spng-Mir |
| Парткод: | 021-17589-008 |
| Деталь: | *Adj. Bracket Front BKT-ADJ-CR1-F |
| Парткод: | 021-17559-001 |
| Деталь: | *Slide Guide Slide-Bush Carriage |
| Парткод: | 021-17564-005 |
| Деталь: | *Guide Bracket Guide-Ffc-Cr1 |
| Парткод: | 021-17570-005 |
| Деталь: | *Reflector |
| Парткод: | 021-17556-002 |
| Деталь: | *Wire Harness Assy-Ffc |
| Парткод: | 021-51120-000 |
| Деталь: | *Lamp Uxfl-08Yg37P2 |
| Парткод: | 021-53143-008 |
| Деталь: | *Frame Carriage 2 Frm-Cr2 |
| Парткод: | 021-17560-000 |
| Деталь: | *Bracket F BKT-SllDE-CR2-F |
| Парткод: | 021-17561-006 |
| Деталь: | *Mirror 2 Carriage 2 |
| Парткод: | 021-17581-007 |
| Деталь: | *Support Shaft Sft-Cr2 Carriage 2 |
| Парткод: | 021-17523-007 |
| Деталь: | *Bracket Rear Pulley K-DV-R |
| Парткод: | 021-17506-005 |
| Деталь: | *Pulley Dv-19-H5-W0.25 |
| Парткод: | 021-17582-003 |
| Деталь: | *Guide Pulley Ply-Turn |
| Парткод: | 021-17565-001 |
| Деталь: | *Bracket Front Pulley BKT-DV-CR2-F |
| Парткод: | 021-17562-100 |
| Деталь: | *Pulley Drive Shaft Ply-Drive |
| Парткод: | 021-17521-004 |
| Деталь: | *Wire Front Wr-7X7-S-F |
| Парткод: | 021-17507-001 |
| Деталь: | *Wire Rear Wr-7X7-Z-R |
| Парткод: | 021-17508-008 |
| Деталь: | *Pulley Ply-S1.5M-75 |
| Парткод: | 021-17574-000 |
| Деталь: | *Belt ST1116060 |
| Парткод: | 021-17584-006 |
| Деталь: | *Belt ST1173060 |
| Парткод: | 021-17583-000 |
| Деталь: | *Bracket Pulley BKT-DV |
| Парткод: | 021-17540-009 |
| Деталь: | *Shaft Pulley Sft-Dv |
| Парткод: | 021-17579-002 |
| Деталь: | *Bracket BKT-WIRE-HOLD |
| Парткод: | 021-17557-009 |
| Деталь: | *Plate Spring Spr-Mir-2 |
| Парткод: | 021-17529-005 |
| Деталь: | Wire Harness Rear Motor U |
| Парткод: | 024-53021-001 |
| Деталь: | Front door |
| Парткод: | 024-34001-008 |
| Деталь: | Emblem MZ770 E |
| Парткод: | 024-34046-109 |
| Деталь: | Emblem MZ770 A |
| Парткод: | 024-34053-008 |
| Деталь: | Emblem MZ790 U |
| Парткод: | 024-34052-001 |
| Деталь: | Emblem MV7690 |
| Парткод: | 024-34048-004 |
| Деталь: | Emblem MZ970 |
| Парткод: | 024-34067-009 |
| Деталь: | Emblem MZ990 |
| Парткод: | 024-34068-005 |
| Деталь: | MAGNET CATCH |
| Парткод: | 021-11220-002 |
| Деталь: | Cover Catch |
| Парткод: | 660-05106-002 |
| Деталь: | Detection Plate Front Door |
| Парткод: | 024-34040-003 |
| Деталь: | Hinge Plate Assy |
| Парткод: | 024-34012-000 |
| Деталь: | Magnet Catch SM-50P |
| Парткод: | 660-05000-018 |
| Деталь: | Bracket Magnet Catch |
| Парткод: | 024-34036-006 |
| Деталь: | Door Catch |
| Парткод: | 660-05105-006 |
| Деталь: | Fixed Plate Rotary Catch |
| Парткод: | 021-11140-009 |
| Деталь: | Inner Cover Right |
| Парткод: | 024-34005-208 |
| Деталь: | Seal M-M Unit Release Pic |
| Парткод: | 024-28203-006 |
| Деталь: | Seal M-M Unit Release Eng |
| Парткод: | 024-28202-000 |
| Деталь: | Inner Cover Upper |
| Парткод: | 024-34002-209 |
| Деталь: | Sear Drum Release Pic |
| Парткод: | 024-34045-005 |
| Деталь: | Sear Drum Release Eng |
| Парткод: | 024-34044-009 |
| Деталь: | Window M-Loading |
| Парткод: | 024-34025-004 |
| Деталь: | Cover Separator Adj |
| Парткод: | 024-34026-000 |
| Деталь: | Inner Cover Lower |
| Парткод: | 024-34003-108 |
| Деталь: | Seal Counter Pic |
| Парткод: | 021-04051-009 |
| Деталь: | Seal Counter Eng |
| Парткод: | 021-04050-002 |
| Деталь: | UPPER COVER RIGHT |
| Парткод: | 024-34011-100 |
| Деталь: | Cover Cap Holder |
| Парткод: | 024-34037-002 |
| Деталь: | Cover Digitizer Pen Case |
| Парткод: | 024-34028-003 |
| Деталь: | Cover M-Removal 2 |
| Парткод: | 024-25103-000 |
| Деталь: | COVER PANEL LOWER |
| Парткод: | 024-37103-103 |
| Деталь: | Upper Cover Rear |
| Парткод: | 024-34010-201 |
| Деталь: | Inner Cover Left |
| Парткод: | 024-34004-309 |
| Деталь: | Cover M-Removal 1 |
| Парткод: | 024-24103-104 |
| Деталь: | UPPER COVER LEFT |
| Парткод: | 024-34009-106 |
| Деталь: | Bracket Lower Cover |
| Парткод: | 024-34032-000 |
| Деталь: | REAR COVER LEFT |
| Парткод: | 024-34006-000 |
| Деталь: | REAR COVER RIGHT |
| Парткод: | 024-34007-103 |
| Деталь: | Seal Ink Replace Instruction Pic |
| Парткод: | 024-17306-008 |
| Деталь: | *Write Roller Assy A3 (13-15) |
| Парткод: | 024-75076-055 |
| Деталь: | *Cutter Unit Assy (26-28) |
| Парткод: | 024-75070-057 |
| Деталь: | *Shaft M. Loading Roller |
| Парткод: | 023-28044-008 |
| Деталь: | *De-Electricity Brush M Loading |
| Парткод: | 023-28415-006 |
| Деталь: | *Bracket De-Elect. Brush M Loading |
| Парткод: | 023-28405-108 |
| Деталь: | *M. Loading Roller A3 |
| Парткод: | 023-28046-000 |
| Деталь: | *Metal F6X8X4 10X1 |
| Парткод: | 607-10006-000 |
| Деталь: | *Lock Ring 4 |
| Парткод: | 023-17197-007 |
| Деталь: | *Gear M0.8X13X5 |
| Парткод: | 612-10103-006 |
| Деталь: | *Load Roller A3 |
| Парткод: | 023-28048-003 |
| Деталь: | *Metal F8X10X8 12X1.5 |
| Парткод: | 607-15005-002 |
| Деталь: | *Gear M0.8X16X5 |
| Парткод: | 612-10104-002 |
| Деталь: | *Stocker Roller A3 |
| Парткод: | 023-28045-004 |
| Деталь: | *PULLEY P40-2GT-5 |
| Парткод: | 611-90011-002 |
| Деталь: | **Write Roller D23-A3 |
| Парткод: | 023-28037-109 |
| Деталь: | **Write Roller liner 3 |
| Парткод: | 023-28432-105 |
| Деталь: | **liner |
| Парткод: | 019-35025-008 |
| Деталь: | *Bearing 6900ZZNR |
| Парткод: | 601-10228-000 |
| Деталь: | *Bracket Rear Write Roller |
| Парткод: | 023-28341-002 |
| Деталь: | *Pressure Plate Write Roller |
| Парткод: | 023-28380-008 |
| Деталь: | *Bracket Front Write Roller |
| Парткод: | 023-28342-106 |
| Деталь: | *Pulley P70-2Gt-5 |
| Парткод: | 611-90012-009 |
| Деталь: | *Bracket Write Motor |
| Парткод: | 023-28041-009 |
| Деталь: | *Gear Pulley M0.5X130+17-2 |
| Парткод: | 613-10002-002 |
| Деталь: | *Belt 256-2GT-4 |
| Парткод: | 620-80001-008 |
| Деталь: | *Motor PM42L-048-ZVS6 |
| Парткод: | 490-33015-002 |
| Деталь: | *Stepped Screw F5X3 M3X3 |
| Парткод: | 635-10007-001 |
| Деталь: | **Cutter unit (Rotary) |
| Парткод: | 023-28421-103 |
| Деталь: | **Master Guide Plate A A3(D23) |
| Парткод: | 023-28327-107 |
| Деталь: | **Seal Pos. Leading Edge Of Master Pic |
| Парткод: | 023-28946-001 |
| Деталь: | *Cutter Guide U |
| Парткод: | 024-28101-106 |
| Деталь: | *Cutter Guide L |
| Парткод: | 024-28117-002 |
| Деталь: | *Sensor E-3674 |
| Парткод: | 444-39000-004 |
| Деталь: | *Guide M-Feed |
| Парткод: | 024-28103-001 |
| Деталь: | *M-Loading Guide |
| Парткод: | 024-28008-009 |
| Деталь: | *M Transfer Roller Short Width |
| Парткод: | 023-28192-104 |
| Деталь: | *M Transfer Roller Middle width |
| Парткод: | 023-28191-108 |
| Деталь: | *M Transfer Roller Wide Width |
| Парткод: | 023-28190-101 |
| Деталь: | *Shaft Load Roller Upper A3 |
| Парткод: | 023-28093-009 |
| Деталь: | *Shaft Stocker roller Upper A3 |
| Парткод: | 023-28184-004 |
| Деталь: | *Bracket L Motor Assy |
| Парткод: | 024-28134-004 |
| Деталь: | *Gear Mx0.5X89+M0.8X34 |
| Парткод: | 612-80019-002 |
| Деталь: | *Gear M0.8X36+M0.8X18 |
| Парткод: | 612-80018-006 |
| Деталь: | *Bracket Gear W |
| Парткод: | 024-28176-009 |
| Деталь: | *Gear M0.8X34X4 |
| Парткод: | 612-10106-005 |
| Деталь: | *Gear M0.8X16X4 |
| Парткод: | 612-10105-009 |
| Деталь: | *Bracket Clamp Motor |
| Парткод: | 024-26006-009 |
| Деталь: | *Motor Assy (CWRS-445PA) |
| Парткод: | 023-75906-077 |
| Деталь: | *Support Clamp Worm |
| Парткод: | 030-19205-001 |
| Деталь: | *Shaft Clamp B |
| Парткод: | 024-26003-000 |
| Деталь: | *Gear M0.8X35+M0.8X15 |
| Парткод: | 612-81303-006 |
| Деталь: | *Shaft Clamp A |
| Парткод: | 024-26002-003 |
| Деталь: | *Gear M0.8X60+M0.8X16 |
| Парткод: | 612-10006-000 |
| Деталь: | *Shaft Clamp Cam |
| Парткод: | 024-26014-001 |
| Деталь: | *Shaft Clamp Slide Cam |
| Парткод: | 024-26012-009 |
| Деталь: | *Gear M0.8X60X7 |
| Парткод: | 612-10203-000 |
| Деталь: | *Clamp Cam 1 |
| Парткод: | 024-26009-008 |
| Деталь: | *Clamp Sliding Cam 1 |
| Парткод: | 024-26008-001 |
| Деталь: | *Spring DE510 |
| Парткод: | 024-26019-003 |
| Деталь: | *Plate Clamp Base |
| Парткод: | 024-26013-005 |
| Деталь: | *Bracket B Position Sensor |
| Парткод: | 023-15150-003 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | *Edging Saddle TSB-1909L |
| Парткод: | 665-04068-006 |
| Деталь: | *Wire Harness M-M Rear |
| Парткод: | 024-28504-006 |
| Деталь: | *Wire Saddle LWS-0711 |
| Парткод: | 665-02044-002 |
| Деталь: | *Wire Harness M-M Front |
| Парткод: | 024-28508-109 |
| Деталь: | Duct Assy (10,11) |
| Парткод: | 024-21037-003 |
| Деталь: | Air Pump Assy (24-39) |
| Парткод: | 024-75082-055 |
| Деталь: | Nozzle Base |
| Парткод: | 024-21013-007 |
| Деталь: | Plate Light Absorber 1st |
| Парткод: | 024-21336-000 |
| Деталь: | Light Absorber Strip (35X28) |
| Парткод: | 023-21393-007 |
| Деталь: | Nozzle Rear |
| Парткод: | 024-21014-208 |
| Деталь: | Nozzle Front |
| Парткод: | 024-21015-204 |
| Деталь: | Bracket Nozzle |
| Парткод: | 024-21016-006 |
| Деталь: | Bracket Nozzle B |
| Парткод: | 024-21017-002 |
| Деталь: | Fan cover |
| Парткод: | 024-21035-000 |
| Деталь: | Fan D12F-24PLH1C13 |
| Парткод: | 490-41013-108 |
| Деталь: | *Outer Duct |
| Парткод: | 024-21029-000 |
| Деталь: | *Inner Duct |
| Парткод: | 024-21020-003 |
| Деталь: | Separator MZ |
| Парткод: | 024-21038-000 |
| Деталь: | SHAFT SEPARATOR |
| Парткод: | 024-21002-005 |
| Деталь: | Power Band T10 |
| Парткод: | 665-02901-002 |
| Деталь: | Air Hose 940 |
| Парткод: | 024-21007-007 |
| Деталь: | Lever Separator Release |
| Парткод: | 024-21003-206 |
| Деталь: | Air Hose 710 |
| Парткод: | 024-21030-009 |
| Деталь: | Metal F8X13/12X5 16X2 |
| Парткод: | 607-15000-000 |
| Деталь: | Separator ADJ |
| Парткод: | 024-21006-000 |
| Деталь: | RELEASE PLATE |
| Парткод: | 023-21001-001 |
| Деталь: | Plate Hose Protect |
| Парткод: | 024-21036-007 |
| Деталь: | Hose Fix Plate |
| Парткод: | 024-21335-004 |
| Деталь: | Wire Harness Mid Feed H |
| Парткод: | 024-53027-107 |
| Деталь: | *Cylinder Base Bracket Air pump |
| Парткод: | 023-21013-204 |
| Деталь: | *Gear M1X80X10 |
| Парткод: | 612-03106-148 |
| Деталь: | *Timing Plate Air Pump |
| Парткод: | 023-21023-102 |
| Деталь: | *Arm Air Pump |
| Парткод: | 019-13511-103 |
| Деталь: | *Arm Shaft Air Pump |
| Парткод: | 019-13512-002 |
| Деталь: | *Piston Head II Air Pump |
| Парткод: | 019-13516-105 |
| Деталь: | *O Ring 34-3.6 |
| Парткод: | 640-67340-009 |
| Деталь: | *Cylinder Valve II Air Pump |
| Парткод: | 019-13517-004 |
| Деталь: | *Cylinder Valve Sheet Air Pump |
| Парткод: | 019-13518-000 |
| Деталь: | *Cylinder Air Pump |
| Парткод: | 023-21021-002 |
| Деталь: | *Adj. Valve Air blow |
| Парткод: | 023-21011-104 |
| Деталь: | *Spring Adj. Valve Air Blow |
| Парткод: | 023-21010-000 |
| Деталь: | *Stepped Screw 6X1.7 M4X4 |
| Парткод: | 635-17614-108 |
| Деталь: | *Lever Pressure Release |
| Парткод: | 024-21033-008 |
| Деталь: | *Base Pressure Release |
| Парткод: | 024-21032-001 |
| Деталь: | *Solenoid Tds-10A-1056 |
| Парткод: | 490-50006-009 |
| Деталь: | Wire Harness Rear Lower B |
| Парткод: | 024-53012-100 |
| Деталь: | Wire Harness Rear Lower A |
| Парткод: | 024-53011-103 |
| Деталь: | Wire Harness RU Motor J |
| Парткод: | 024-53009-001 |
| Деталь: | Wire Harness Rear Motor U |
| Парткод: | 024-53021-001 |
| Деталь: | Guide Roll Release Unit (1-8) |
| Парткод: | 024-75069-059 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | *Bracket B Position Sensor |
| Парткод: | 023-15150-003 |
| Деталь: | *G Roll Release Cover |
| Парткод: | 024-15181-003 |
| Деталь: | *G Roll Release Cam |
| Парткод: | 024-15182-000 |
| Деталь: | *Gear M0.8X17+M0.8X49 |
| Парткод: | 612-81401-008 |
| Деталь: | *Gear M0.8X35+M0.8X15 |
| Парткод: | 612-81303-006 |
| Деталь: | *G Roller Release Base Assy |
| Парткод: | 024-15176-000 |
| Деталь: | *Motor Assy (CWRS-445PA) |
| Парткод: | 023-75906-077 |
| Деталь: | Cover Main Drive T-Mission |
| Парткод: | 024-16056-008 |
| Деталь: | Bracket Main Motor Shaft |
| Парткод: | 030-12235-100 |
| Деталь: | Plate T-Roller Shaft Assy |
| Парткод: | 024-15191-009 |
| Деталь: | Gear M1X70X22 |
| Парткод: | 612-16018-000 |
| Деталь: | Gear M1X90X22 |
| Парткод: | 612-16023-004 |
| Деталь: | Bracket Main T-Mission |
| Парткод: | 024-16053-009 |
| Деталь: | Main Cover Assy |
| Парткод: | 024-15051-100 |
| Деталь: | Bracket Pressure Shaft |
| Парткод: | 023-15012-000 |
| Деталь: | Bracket Drive Encoder |
| Парткод: | 024-15190-002 |
| Деталь: | Drive Encoder |
| Парткод: | 024-15186-005 |
| Деталь: | Detection Plate B |
| Парткод: | 024-15153-000 |
| Деталь: | Pressure Cam A3 |
| Парткод: | 024-15011-000 |
| Деталь: | Pressure Cam LD |
| Парткод: | 024-16066-003 |
| Деталь: | 2nd Drum Drive Gear Assy |
| Парткод: | 024-16085-008 |
| Деталь: | 1st Drum Drive Gear Assy |
| Парткод: | 024-16080-006 |
| Деталь: | Separation Cam |
| Парткод: | 024-16067-000 |
| Деталь: | Joint Drive Assy |
| Парткод: | 024-15003-105 |
| Деталь: | Wire Harness RU Sensor J |
| Парткод: | 024-53020-005 |
| Деталь: | Wire Harness PFL Sensor |
| Парткод: | 024-12605-007 |
| Деталь: | Wire Harness Rear Sensor U |
| Парткод: | 024-53019-007 |
| Деталь: | Drum Frame Front |
| Парткод: | 024-17048-009 |
| Деталь: | Pin Catch R Assy |
| Парткод: | 024-17503-008 |
| Деталь: | Stepped Screw F6X4 M4X6 |
| Парткод: | 635-10010-002 |
| Деталь: | O Ring P6-1.9 |
| Парткод: | 640-60060-000 |
| Деталь: | Pin Catch L Assy |
| Парткод: | 024-17502-001 |
| Деталь: | Bracket Drum Lever L |
| Парткод: | 024-17402-007 |
| Деталь: | Bracket Drum Lever R |
| Парткод: | 024-17401-000 |
| Деталь: | Drum Lever |
| Парткод: | 024-17095-007 |
| Деталь: | Cover Drum Release |
| Парткод: | 024-17135-009 |
| Деталь: | Bracket Drum Lock |
| Парткод: | 024-17154-003 |
| Деталь: | Shaft Drum Lock Plate |
| Парткод: | 024-17138-105 |
| Деталь: | Square Bushing SB-2718 |
| Парткод: | 665-04054-005 |
| Деталь: | Drum Lock Plate |
| Парткод: | 024-17136-005 |
| Деталь: | Drum Lock Arm |
| Парткод: | 024-17403-003 |
| Деталь: | Shaft Drum Lock |
| Парткод: | 024-17162-006 |
| Деталь: | Drum Lock Joint Plate |
| Парткод: | 024-17161-000 |
| Деталь: | Drum Lock Joint Shaft |
| Парткод: | 024-17404-000 |
| Деталь: | Stepped Screw F5X2 M3X3:SG |
| Парткод: | 635-10011-009 |
| Деталь: | Spring Drum Lock link |
| Парткод: | 023-17177-006 |
| Деталь: | Plate Drum ADJ |
| Парткод: | 024-17517-009 |
| Деталь: | BRACKET DRAWER |
| Парткод: | 024-18025-002 |
| Деталь: | Wire Harness Drum Drawer |
| Парткод: | 024-17171-102 |
| Деталь: | Connector Spring |
| Парткод: | 030-16820-001 |
| Деталь: | Stepped Screw F4X18.5 M3X6 |
| Парткод: | 635-17493-009 |
| Деталь: | Bracket Drum PCB |
| Парткод: | 024-17175-000 |
| Деталь: | Drum PCB |
| Парткод: | 024-17178-000 |
| Деталь: | Lever B Position Lock |
| Парткод: | 024-17051-000 |
| Деталь: | Cover B Position Lock Lever |
| Парткод: | 023-17244-005 |
| Деталь: | Shaft B Position Release |
| Парткод: | 024-17152-000 |
| Деталь: | Collar B Position |
| Парткод: | 024-17509-006 |
| Деталь: | Lock Chip B-Position |
| Парткод: | 024-17273-002 |
| Деталь: | Lock Spring B Pos. |
| Парткод: | 023-17054-001 |
| Деталь: | Stay Drum Frame Front |
| Парткод: | 023-17192-005 |
| Деталь: | STAY DRUM FRAME |
| Парткод: | 024-17046-006 |
| Деталь: | Drum Guide |
| Парткод: | 023-17092-000 |
| Деталь: | Drum Frame Rear |
| Парткод: | 023-17044-200 |
| Деталь: | Cover Rear Handle |
| Парткод: | 023-17176-000 |
| Деталь: | liner Pom Rear Frame Drum |
| Парткод: | 023-17094-003 |
| Деталь: | Cover Front Frame |
| Парткод: | 024-17091-109 |
| Деталь: | Seal Drum Set Position |
| Парткод: | 023-17302-005 |
| Деталь: | Seal Setting Cartridge |
| Парткод: | 023-17301-009 |
| Деталь: | B Position Marking Sticker |
| Парткод: | 023-17307-007 |
| Деталь: | Seal Ink Color |
| Парткод: | 023-17306-108 |
| Деталь: | Seal Ink Black |
| Парткод: | 023-17320-003 |
| Деталь: | Seal Drum Type |
| Парткод: | 023-17321-301 |
| Деталь: | *Side M-Removal Plate F |
| Парткод: | 024-24002-006 |
| Деталь: | *Side M-Removal Plate R |
| Парткод: | 024-24009-000 |
| Деталь: | *Stay M-Removal A1 |
| Парткод: | 024-24016-007 |
| Деталь: | *Bracket Vertical FG Sensor 1 |
| Парткод: | 024-24075-003 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | *Wire Removal Feed FG1 |
| Парткод: | 024-24102-000 |
| Деталь: | *Stay M-Removal B1 |
| Парткод: | 024-24017-003 |
| Деталь: | *Bracket M-Loading Sensor 1 |
| Парткод: | 024-24027-009 |
| Деталь: | *Master Sensor 3 |
| Парткод: | 020-60006-205 |
| Деталь: | Compression plate |
| Парткод: | 024-24099-000 |
| Деталь: | *Metal F10X15/14X6 18X2 |
| Парткод: | 607-16001-000 |
| Деталь: | *Pulley Gear 0.8X31+53S2M |
| Парткод: | 613-11300-007 |
| Деталь: | *Belt 40-S2M-290 |
| Парткод: | 621-00001-000 |
| Деталь: | *Gear m0.8X61+m1.25X12 |
| Парткод: | 612-80024-006 |
| Деталь: | *Bracket MR Feed Gear |
| Парткод: | 024-25001-003 |
| Деталь: | *Motor CCWRS-555PH-24100 |
| Парткод: | 023-75907-073 |
| Деталь: | ** Metal Slit Motor |
| Парткод: | 023-21342-003 |
| Деталь: | *Bracket Gear A |
| Парткод: | 024-24138-005 |
| Деталь: | *Gear M 1X71X14 |
| Парткод: | 61 2-1 0040-004 |
| Деталь: | *Bracket Gear B |
| Парткод: | 024-24139-001 |
| Деталь: | *Gear M0.8X17+M0.8X49 |
| Парткод: | 612-81401-008 |
| Деталь: | *Cover Compress Gear 1 |
| Парткод: | 024-24097-104 |
| Деталь: | *Gear M1X17+M0.8X61 |
| Парткод: | 612-81602-003 |
| Деталь: | *Gear M0.8X15X7 |
| Парткод: | 612-11103-000 |
| Деталь: | *Bracket FG Sensor Compression Plate |
| Парткод: | 023-24074-000 |
| Деталь: | *Wire Harness MM Safety Lead SW |
| Парткод: | 024-53040-006 |
| Деталь: | *Stepped Screw F5X1.5 M3X3 |
| Парткод: | 635-18513-003 |
| Деталь: | *Set Plate Safety SW M.-Rmv. |
| Парткод: | 023-24135-009 |
| Деталь: | *Spring Safety SW M-Rmv Unit |
| Парткод: | 023-24134-100 |
| Деталь: | *M-Removal Roller |
| Парткод: | 024-25005-009 |
| Деталь: | *Hook Shaft M Removal Roller Lower |
| Парткод: | 023-24124-007 |
| Деталь: | *Retention Plate F |
| Парткод: | 024-24125-000 |
| Деталь: | *Retention Plate R |
| Парткод: | 024-24127-003 |
| Деталь: | *Stepped Screw F5X10.8 M3X3 |
| Парткод: | 635-10006-005 |
| Деталь: | Roller Hook M.-Rmv. |
| Парткод: | 023-24126-000 |
| Деталь: | *MetalF8X12/11X10 15X2 |
| Парткод: | 607-15000-400 |
| Деталь: | *Gear m1.25X16+m1.25X14 |
| Парткод: | 612-80025-002 |
| Деталь: | *Link Plate |
| Парткод: | 024-25065-001 |
| Деталь: | *Manual Compression Lever |
| Парткод: | 023-24120-001 |
| Деталь: | *Box Guide Plate |
| Парткод: | 024-24119-000 |
| Деталь: | *M-Release Lever 1 |
| Парткод: | 024-24113-002 |
| Деталь: | *Knob Release Lever M.-Rmv. |
| Парткод: | 023-24117-000 |
| Деталь: | *Metal F8X13/12X5 16X2 |
| Парткод: | 607-15000-000 |
| Деталь: | *Bracket Compress Motor |
| Парткод: | 024-24091-009 |
| Деталь: | *Gear M0.8X35+M0.8X15 |
| Парткод: | 612-81303-006 |
| Деталь: | *Motor Assy (CWRS-445PA) |
| Парткод: | 023-75906-077 |
| Деталь: | *Support Clamp Worm |
| Парткод: | 030-19205-001 |
| Деталь: | *Wire Harness Removal Compress 1 |
| Парткод: | 024-24101-004 |
| Деталь: | *Wire Harness Removal Feed 1 |
| Парткод: | 024-24100-002 |
| Деталь: | *Wire Saddle LWS-0711 |
| Парткод: | 665-02044-002 |
| Деталь: | Wire Harness MRV1 Joint |
| Парткод: | 024-53016-105 |
| Деталь: | Stepped Screw F5X3.5 M3X4.5 |
| Парткод: | 635-17533-000 |
| Деталь: | Guide Wire Harness M-M |
| Парткод: | 024-28159-007 |
| Деталь: | Lock Ring |
| Парткод: | 019-11812-106 |
| Деталь: | Base Plate M-M |
| Парткод: | 024-28156-008 |
| Деталь: | Stopper M-M Base |
| Парткод: | 024-28069-008 |
| Деталь: | Base M-M Unit Rack |
| Парткод: | 024-28052-008 |
| Деталь: | M-M Rack |
| Парткод: | 024-28048-000 |
| Деталь: | Slide Rail (S101) |
| Парткод: | 024-28047-004 |
| Деталь: | Cover M-Loading Sensor 2 |
| Парткод: | 024-28147-009 |
| Деталь: | Sensor KH0726-00 |
| Парткод: | 444-43000-507 |
| Деталь: | Wire Harness ML Sensor 2 |
| Парткод: | 024-53029-002 |
| Деталь: | Bracket M-Loading Sensor 2 |
| Парткод: | 024-28146-002 |
| Деталь: | Fixed Plate Slide Shaft A |
| Парткод: | 024-28148-005 |
| Деталь: | Bracket MM Junction PCB |
| Парткод: | 024-50016-007 |
| Деталь: | MMR-PCB |
| Парткод: | 024-28501-007 |
| Деталь: | Bracket M-M Position |
| Парткод: | 024-28122-103 |
| Деталь: | Bracket B Position Sensor |
| Парткод: | 023-15150-003 |
| Деталь: | Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | Fixed Plate Slide Shaft B |
| Парткод: | 024-28033-003 |
| Деталь: | Bracket Unit Stopper R |
| Парткод: | 024-28061-007 |
| Деталь: | Spring Unit Stopper |
| Парткод: | 024-28038-005 |
| Деталь: | Unit Stopper R |
| Парткод: | 024-28060-000 |
| Деталь: | Shaft Unit Stopper |
| Парткод: | 024-28036-002 |
| Деталь: | Wire Saddle LWS-1316 |
| Парткод: | 665-02043-006 |
| Деталь: | Reinforce Plate M-M Cover |
| Парткод: | 024-28053-101 |
| Деталь: | Shaft M-M Cover Hook |
| Парткод: | 024-28022-001 |
| Деталь: | Hook Spring |
| Парткод: | 024-28023-105 |
| Деталь: | Lever M-M Unit |
| Парткод: | 024-28032-104 |
| Деталь: | Hook M-M Unit Cover |
| Парткод: | 024-28021-102 |
| Деталь: | Fixed Plate M-M Cover R |
| Парткод: | 024-28028-107 |
| Деталь: | Fixed Shaft M-M Cover R |
| Парткод: | 024-28070-006 |
| Деталь: | Fixed Plate M-M Cover F |
| Парткод: | 024-28065-100 |
| Деталь: | Fixed Shaft M-M Cover F |
| Парткод: | 024-28071-100 |
| Деталь: | Cover M-M Unit |
| Парткод: | 024-28020-106 |
| Деталь: | Seal Master Set |
| Парткод: | 024-28206-005 |
| Деталь: | Bracket M-M Lock |
| Парткод: | 024-28012-006 |
| Деталь: | Hook Stopper |
| Парткод: | 024-28015-005 |
| Деталь: | Shaft Hook Stopper M-M |
| Парткод: | 024-28063-000 |
| Деталь: | Hook Stopper M-M |
| Парткод: | 024-28062-003 |
| Деталь: | Spring Hook Stopper M-M |
| Парткод: | 024-28016-001 |
| Деталь: | Spring M-M Stopper |
| Парткод: | 024-28064-006 |
| Деталь: | BRACKET SAFETY SW |
| Парткод: | 024-28017-008 |
| Деталь: | Spring Safety SW /Drum&Mm |
| Парткод: | 023-28403-008 |
| Деталь: | BRACKET SWITCH |
| Парткод: | 024-28059-002 |
| Деталь: | Wire Harness M-M Safety SW |
| Парткод: | 024-53040-006 |
| Деталь: | Push Button SW Assy |
| Парткод: | 021-51029-003 |
| Деталь: | Wire Harness MRV2 Joint |
| Парткод: | 024-53037-005 |
| Деталь: | Wire Harness F-Safety SW |
| Парткод: | 024-53034-006 |
| Деталь: | Wire Harness M-M Unit FCC |
| Парткод: | 024-53001-000 |
| Деталь: | Wire Harness Rear Upper |
| Парткод: | 024-53010-107 |
| Деталь: | Wire Harness Rear PS Upper |
| Парткод: | 024-53002-007 |
| Деталь: | Wire Harness TPH CTL Joint |
| Парткод: | 024-53051-008 |
| Деталь: | Wire Harness Rear Sensor U |
| Парткод: | 024-53019-007 |
| Деталь: | Vertical Drive Unit (9-17) |
| Парткод: | 024-75095-050 |
| Деталь: | Print Position CTL Unit (27-36) |
| Парткод: | 024-75096-056 |
| Деталь: | Main Motor Assy (37-40) |
| Парткод: | 024-75085-054 |
| Деталь: | Brake Unit (1-6) |
| Парткод: | 024-75090-058 |
| Деталь: | *OPB10N |
| Парткод: | 490-52000-008 |
| Деталь: | *Gear M0.8X33X14 |
| Парткод: | 612-16033-000 |
| Деталь: | *Cover D-Brake |
| Парткод: | 024-16261-000 |
| Деталь: | *Gear M0.8X76+M1X32 |
| Парткод: | 612-16034-006 |
| Деталь: | *Gear M1X80+M1X46 |
| Парткод: | 612-16031-007 |
| Деталь: | *D-BASE BRAKE ASSY |
| Парткод: | 024-16264-000 |
| Деталь: | Gear M1X94X15 |
| Парткод: | 612-16020-005 |
| Деталь: | 2nd PUMP JOINT SHAFT ASSY |
| Парткод: | 024-16043-003 |
| Деталь: | *Gear Vertical Positioning OUT |
| Парткод: | 024-16083-005 |
| Деталь: | *Carrier Assy |
| Парткод: | 024-16020-003 |
| Деталь: | *Gear M1X36+M1X24 |
| Парткод: | 612-16027-107 |
| Деталь: | *Stay Planet Gear |
| Парткод: | 024-16039-006 |
| Деталь: | *Cover Planet Gear |
| Парткод: | 024-16033-008 |
| Деталь: | *Main Shaft Vertical |
| Парткод: | 024-16009-107 |
| Деталь: | *Gear Vertical Positioning IN |
| Парткод: | 024-16078-001 |
| Деталь: | *Plate Print Positioning ADJ (IN) |
| Парткод: | 024-16007-007 |
| Деталь: | *Gear M1X126X9 |
| Парткод: | 612-16026-003 |
| Деталь: | Plate Vertical Drive Shaft |
| Парткод: | 024-16015-107 |
| Деталь: | Gear M1X74+M1X64 |
| Парткод: | 612-16029-002 |
| Деталь: | Mid-Feed Drive Base Assy |
| Парткод: | 024-16266-002 |
| Деталь: | Bearing Main Shaft |
| Парткод: | 023-15001-008 |
| Деталь: | Stay Main Cover |
| Парткод: | 024-15189-004 |
| Деталь: | Cover 1st Pump Drive |
| Парткод: | 024-16272-002 |
| Деталь: | Gear M1X54+M1X40 |
| Парткод: | 612-16038-001 |
| Деталь: | Gear M1X40X12 |
| Парткод: | 612-16036-009 |
| Деталь: | 1st Pump Drive Base Assy |
| Парткод: | 024-16270-000 |
| Деталь: | *Cover Print Positioning |
| Парткод: | 024-16034-101 |
| Деталь: | *Gear M0.8X35+M0.8X15 |
| Парткод: | 612-81303-006 |
| Деталь: | *Spring Positioning Control |
| Парткод: | 024-16042-007 |
| Деталь: | *Plate Position Control |
| Парткод: | 024-16041-108 |
| Деталь: | *Gear M1X32X10 |
| Парткод: | 612-10046-002 |
| Деталь: | *Gear M1X16+M0.8X42 |
| Парткод: | 612-10044-000 |
| Деталь: | *Gear M1X60+M1X18 |
| Парткод: | 612-10045-006 |
| Деталь: | *Gear Position Control |
| Парткод: | 024-16065-104 |
| Деталь: | *Motor PM42L-048-ZVN5 |
| Парткод: | 490-33016-009 |
| Деталь: | *Positioning Hook Plate |
| Парткод: | 024-16028-101 |
| Деталь: | *Gear M1X54X22 |
| Парткод: | 612-16025-104 |
| Деталь: | *Bracket Main Motor |
| Парткод: | 024-15047-005 |
| Деталь: | *Square Bushing SB-2718 |
| Парткод: | 665-04054-005 |
| Деталь: | *TD3348G-300-10K12A |
| Парткод: | 490-22019-006 |
| Деталь: | Wire Harness Main Motor TD |
| Парткод: | 024-53060-007 |
| Деталь: | Wire Harness Main Motor TD EU |
| Парткод: | 024-53061-003 |
| Деталь: | Wire Harness Main FG |
| Парткод: | 024-53038-206 |
| Деталь: | Wire Harness RU Motor J |
| Парткод: | 024-53009-001 |
| Деталь: | Wire Harness Rear Motor U |
| Парткод: | 024-53021-001 |
| Деталь: | Cartridge Guide Assy (6 ) |
| Парткод: | 023-75123-056 |
| Деталь: | Bottle Stay |
| Парткод: | 023-17025-001 |
| Деталь: | Ink Distributor |
| Парткод: | 030-16404-003 |
| Деталь: | O Ring P10A-2.4 |
| Парткод: | 640-60100-100 |
| Деталь: | Ground Plate Ink |
| Парткод: | 023-17254-000 |
| Деталь: | Sensor YAA81-0070N |
| Парткод: | 444-51004-007 |
| Деталь: | *Cartridge Guide Lowe |
| Парткод: | 023-17155-002 |
| Деталь: | *Maintenance Cap |
| Парткод: | 023-17160-006 |
| Деталь: | *Bracket Ink Bottle Set SW |
| Парткод: | 023-17158-001 |
| Деталь: | *Bottle Catch |
| Парткод: | 023-17157-102 |
| Деталь: | *Bottle Set SW Assy |
| Парткод: | 023-17026-105 |
| Деталь: | *Shaft Rf-Tag Reader Drum |
| Парткод: | 023-17249-007 |
| Деталь: | *ARM RF-TAG Reader Holder Drum |
| Парткод: | 023-17248-108 |
| Деталь: | *Spring Rf-Tag Reader Drum |
| Парткод: | 023-17250-005 |
| Деталь: | *Holder RF-TAG Reader Drum |
| Парткод: | 023-17156-009 |
| Деталь: | *Cartridge Guide Upper |
| Парткод: | 023-17024-005 |
| Деталь: | RF-TAG Reader Drum |
| Парткод: | 444-59002-100 |
| Деталь: | Ink Pump Assy (18,19) |
| Парткод: | 023-17145-007 |
| Деталь: | *Gear M1x32x4 |
| Парткод: | 612-12306-001 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | Wire Harness Drum Inner |
| Парткод: | 024-17172-001 |
| Деталь: | 2nd Master removal Unit (Fig29-Fig30) |
| Парткод: | 024-75066-050 |
| Деталь: | *Stay M-Removal C |
| Парткод: | 024-25040-009 |
| Деталь: | *Bracket Removal U-Roller R |
| Парткод: | 024-25039-000 |
| Деталь: | *Bracket Removal U-Roller F |
| Парткод: | 024-25038-004 |
| Деталь: | *Roller Hook |
| Парткод: | 024-25062-100 |
| Деталь: | *Spring Roller Hook |
| Парткод: | 024-25058-005 |
| Деталь: | *Spring Catch |
| Парткод: | 030-19131-008 |
| Деталь: | *Spring Roller |
| Парткод: | 024-25057-009 |
| Деталь: | *Gear m1.25x16x7 |
| Парткод: | 612-10041-000 |
| Деталь: | *Lock Ring 4 |
| Парткод: | 023-17197-007 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | *Bracket M-Jam Sensor 2 |
| Парткод: | 024-25037-008 |
| Деталь: | *Sensor OS-RS04Y01 |
| Парткод: | 444-41003-002 |
| Деталь: | *Wire Harness MR-Sensor 2 |
| Парткод: | 024-25102-004 |
| Деталь: | *Shaft Roller Hook |
| Парткод: | 024-25124-008 |
| Деталь: | *Retention Plate |
| Парткод: | 024-25125-004 |
| Деталь: | *M-Removal Roller |
| Парткод: | 024-25005-009 |
| Деталь: | *Shaft Retention Roller |
| Парткод: | 024-25126-000 |
| Деталь: | *Roller Hook M.-Rmv. |
| Парткод: | 023-24126-000 |
| Деталь: | *Metal F8X12/11X10: 15X2 |
| Парткод: | 607-15000-400 |
| Деталь: | *Gear m1.25X16+m1.25X14 |
| Парткод: | 612-80025-002 |
| Деталь: | *Shaft MR Pulley Plate |
| Парткод: | 024-25007-001 |
| Деталь: | *Pulley Fixed Plate |
| Парткод: | 024-25060-000 |
| Деталь: | *Plate M.-Rmv. Pulley |
| Парткод: | 023-24062-109 |
| Деталь: | *Spring Roller B2 |
| Парткод: | 024-25059-001 |
| Деталь: | *Shaft Pulley M-Rmv |
| Парткод: | 023-24063-202 |
| Деталь: | *Pulley M-Rmv |
| Парткод: | 023-24061-102 |
| Деталь: | *Transfer Belt 2 2X112 |
| Парткод: | 628-00001-000 |
| Деталь: | *Shaft M-Removal Roller |
| Парткод: | 024-25006-005 |
| Деталь: | *Pin F2X14 |
| Парткод: | X-530 |
| Деталь: | *Stepped Screw F5X10.8 M3X3 |
| Парткод: | 635-10006-005 |
| Деталь: | *Link Plate |
| Парткод: | 024-25065-001 |
| Деталь: | *Manual Compression Lever |
| Парткод: | 023-24120-001 |
| Деталь: | *Box Guide Plate |
| Парткод: | 024-24119-000 |
| Деталь: | *M-Release Lever 2 |
| Парткод: | 024-25071-001 |
| Деталь: | *Knob Release Lever M.-Rmv. |
| Парткод: | 023-24117-000 |
| Деталь: | Power Supply 18-HWW |
| Парткод: | 045-50082-000 |
| Деталь: | Wire Harness Rear Upper |
| Парткод: | 024-53010-107 |
| Деталь: | Wire Harness Drive PS |
| Парткод: | 024-53006-002 |
| Деталь: | Wire Harness Rear PS Upper |
| Парткод: | 024-53002-007 |
| Деталь: | Wire Harness PS Switch |
| Парткод: | 024-53005-006 |
| Деталь: | MECHA-CNTL-PCB SU |
| Парткод: | 024-75000-059 |
| Деталь: | BATTERY CR-2032 |
| Парткод: | 408-02300-001 |
| Деталь: | Wire Harness MCTL-PS |
| Парткод: | 024-53007-009 |
| Деталь: | Wire Harness Rear Sensor U |
| Парткод: | 024-53019-007 |
| Деталь: | Wire Harness Rear Motor U |
| Парткод: | 024-53021-001 |
| Деталь: | Bracket PS-MCTL PCB |
| Парткод: | 024-50002-006 |
| Деталь: | Wire Saddle LWS-1316 |
| Парткод: | 665-02043-006 |
| Деталь: | Edging Saddle TSB-1909L |
| Парткод: | 665-04068-006 |
| Деталь: | Edging Saddle TSB-3027L |
| Парткод: | 665-04069-002 |
| Деталь: | Wire Saddle LWS-2218 |
| Парткод: | 665-02055-004 |
| Деталь: | Bracket MID Cover |
| Парткод: | 024-34033-007 |
| Деталь: | Hinge P-Ejection L |
| Парткод: | 024-50004-009 |
| Деталь: | Plate PS PCB Support |
| Парткод: | 024-50023-003 |
| Деталь: | Power Cord 220V EU (L) |
| Парткод: | 488-00048-004 |
| Деталь: | Power Cord RP3 UI |
| Парткод: | 488-00047-105 |
| Деталь: | Wire Saddle LWS-0711 |
| Парткод: | 665-02044-002 |
| Деталь: | SCANNER UNIT |
| Парткод: | 024-75122-006 |
| Деталь: | SCANNER UNIT |
| Парткод: | 024-75123-002 |
| Деталь: | *Original Stopper Assy(1-5) |
| Парткод: | 046-75056-000 |
| Деталь: | *Assy |
| Парткод: | 046-30067-001 |
| Деталь: | *Stage Glass Assy(14-16) |
| Парткод: | 021-17504-002 |
| Деталь: | FB Actuator Assy(32-35) |
| Парткод: | 023-75167-150 |
| Деталь: | **Blind Cover |
| Парткод: | 021-17568-205 |
| Деталь: | **Sponge |
| Парткод: | 046-30062-000 |
| Деталь: | **Sponge |
| Парткод: | 046-30063-006 |
| Деталь: | **SPNG-GID-UCN-L |
| Парткод: | 021-17149-008 |
| Деталь: | **SPNG-GID-UCN-S |
| Парткод: | 021-17150-006 |
| Деталь: | **Adj. Plate |
| Парткод: | 021-17545-205 |
| Деталь: | **Sponge |
| Парткод: | 021-17531-107 |
| Деталь: | **Sponge |
| Парткод: | 021-17530-100 |
| Деталь: | *Screw |
| Парткод: | 021-17525-000 |
| Деталь: | *Sponge |
| Парткод: | 021-17517-007 |
| Деталь: | *Guide Plate |
| Парткод: | 021-17547-100 |
| Деталь: | *Bracket |
| Парткод: | 021-17567-004 |
| Деталь: | *Sensor |
| Парткод: | 021-53141-102 |
| Деталь: | *Wire Harness |
| Парткод: | 021-51121-007 |
| Деталь: | *PCB |
| Парткод: | 021-50535-100 |
| Деталь: | *Cover |
| Парткод: | 046-30038-001 |
| Деталь: | *S-Assy |
| Парткод: | 024-30910-003 |
| Деталь: | *Wire Harness |
| Парткод: | 046-30049-003 |
| Деталь: | *Cover Plate |
| Парткод: | 021-17543-105 |
| Деталь: | *Sensor |
| Парткод: | 021-53142-001 |
| Деталь: | *Wire Harness |
| Парткод: | 021-51122-100 |
| Деталь: | *Plate |
| Парткод: | 021-17544-101 |
| Деталь: | *Guide Bracket |
| Парткод: | 021-17569-007 |
| Деталь: | *Wire Saddle |
| Парткод: | 033-15129-000 |
| Деталь: | BASE PLATE |
| Парткод: | 046-30051-008 |
| Деталь: | WIRE HARNESS |
| Парткод: | 046-30042-009 |
| Деталь: | WIRE HARNESS |
| Парткод: | 046-30043-005 |
| Деталь: | *Spring |
| Парткод: | 021-17129-104 |
| Деталь: | *Actuator 2 |
| Парткод: | 023-30073-007 |
| Деталь: | *Sensor |
| Парткод: | 444-30008-100 |
| Деталь: | *Bracket |
| Парткод: | 023-30071-004 |
| Деталь: | Hinge Bracket |
| Парткод: | 023-30002-100 |
| Деталь: | BRACKET |
| Парткод: | 023-30003-009 |
| Деталь: | EDGING SADDLE |
| Парткод: | 665-00308-002 |
| Деталь: | WIRE HARNESS |
| Парткод: | 046-53008-002 |
| Деталь: | FFC CLAMP |
| Парткод: | 665-00310-007 |
| Деталь: | BRACKET |
| Парткод: | 045-30008-008 |
| Деталь: | Pressure Roller Unit A3 Assy (1-7) |
| Парткод: | 024-75078-058 |
| Деталь: | Stripper Unit (41-63) |
| Парткод: | 024-75072-050 |
| Деталь: | *Unit /Stripper Pad 70 (53-55) |
| Парткод: | 019-91740-003 |
| Деталь: | *Shaft Pressure W |
| Парткод: | 024-19007-008 |
| Деталь: | *Stopper Pressure Roller |
| Парткод: | 023-19012-004 |
| Деталь: | *Shaft Partial pressure |
| Парткод: | 024-19004-009 |
| Деталь: | *Pressure Roller Support Front Assy |
| Парткод: | 023-75071-056 |
| Деталь: | *Pressure Roller Support Rear Assy |
| Парткод: | 023-75072-052 |
| Деталь: | *Stepped Screw 6X1.8 M3X4 |
| Парткод: | 635-17613-004 |
| Деталь: | Metal F16X22/19X6 26X2 |
| Парткод: | 607-10003-001 |
| Деталь: | TIMING ROLLER |
| Парткод: | 024-12506-106 |
| Деталь: | *Pressure Roller A3 (20) |
| Парткод: | 024-75104-059 |
| Деталь: | Support Plate T Roller |
| Парткод: | 024-12520-001 |
| Деталь: | BEARING DDLF-1910ZZR |
| Парткод: | 601-10195-004 |
| Деталь: | METAL F10X15/14X6 18X2 |
| Парткод: | 607-16001-000 |
| Деталь: | Adj. Plate Timing Roller |
| Парткод: | 023-12507-105 |
| Деталь: | Guide Roller MZ |
| Парткод: | 024-12531-100 |
| Деталь: | Support F Guide Roller |
| Парткод: | 023-12515-000 |
| Деталь: | ADJ. Plate Guide Roller |
| Парткод: | 023-12545-007 |
| Деталь: | Metal F8X11/10X5.5 14X2 |
| Парткод: | 607-40001-003 |
| Деталь: | Lock Plate Guide Roller |
| Парткод: | 023-12519-006 |
| Деталь: | Support R Guide Roller |
| Парткод: | 023-12516-007 |
| Деталь: | PRESSURE SHAFT GUIDE ROLLER |
| Парткод: | 023-12513-008 |
| Деталь: | Shaft Guide Roller |
| Парткод: | 024-12507-005 |
| Деталь: | PRESSURE PLATE GUIDE ROLLER |
| Парткод: | 024-12530-007 |
| Деталь: | Bracket Guide Plate L |
| Парткод: | 024-12521-008 |
| Деталь: | GUIDE PLATE UPPER |
| Парткод: | 024-12503-000 |
| Деталь: | Multiple Sensor Shield |
| Парткод: | 024-12519-003 |
| Деталь: | Fixing Plate PF Regist Sensor |
| Парткод: | 024-12511-002 |
| Деталь: | Sensor (Rcv) OF-11R1-N23 |
| Парткод: | 444-32007-003 |
| Деталь: | Cover Multiple Sensor U |
| Парткод: | 024-12510-200 |
| Деталь: | Sensor KH0686-11 |
| Парткод: | 444-42022-000 |
| Деталь: | Wire Harness PF Feed U Sensor |
| Парткод: | 024-12606-003 |
| Деталь: | Guide Plate Lower |
| Парткод: | 024-12501-104 |
| Деталь: | Bracket Multiple Sensor |
| Парткод: | 024-12518-007 |
| Деталь: | Sensor KH0686-10 |
| Парткод: | 444-42021-004 |
| Деталь: | Sensor (Send) OF-11T-N23 |
| Парткод: | 444-32006-007 |
| Деталь: | PF Regist Sensor Slit |
| Парткод: | 024-12527-006 |
| Деталь: | Cover PF Regist Sensor |
| Парткод: | 024-12525-100 |
| Деталь: | Wire Harness PF Feed L Sensor |
| Парткод: | 024-12613-000 |
| Деталь: | Cover Multiple Sensor L |
| Парткод: | 024-12528-100 |
| Деталь: | COVER WIRE HARNESS |
| Парткод: | 024-12529-009 |
| Деталь: | Back Cover Stripper Unit |
| Парткод: | 023-12543-004 |
| Деталь: | *Spring Angle Adj. Stripper |
| Парткод: | 023-12429-104 |
| Деталь: | *Spring Tension Stripper |
| Парткод: | 023-12403-008 |
| Деталь: | *Base Stripper Unit |
| Парткод: | 024-12401-002 |
| Деталь: | *Guide Block Front Stripper Unit |
| Парткод: | 023-12431-001 |
| Деталь: | *Unfix Lever Stripper Unit |
| Парткод: | 023-12430-005 |
| Деталь: | *Fixed Block |
| Парткод: | 030-14521-002 |
| Деталь: | *Lock Lever Stripper Unit |
| Парткод: | 023-12428-000 |
| Деталь: | *Ground Spring Roller System |
| Парткод: | 018-31614-001 |
| Деталь: | *Arm Stripper pressure |
| Парткод: | 023-12412-007 |
| Деталь: | *Bracket Stripper Base |
| Парткод: | 023-12402-109 |
| Деталь: | *Housing Stripper RZ-L |
| Парткод: | 023-12408-204 |
| Деталь: | *Shaft Stripper RZ-L |
| Парткод: | 023-12404-209 |
| Деталь: | **Cover F Stripper Pad |
| Парткод: | 019-11832-000 |
| Деталь: | **Base F Stripper Pad |
| Парткод: | 019-11831-100 |
| Деталь: | **Stripper Pad 70 |
| Парткод: | 019-11833-006 |
| Деталь: | *Stepped Screw 6X2.2 M4X2.5 |
| Парткод: | 635-17624-006 |
| Деталь: | *Stripper Cam |
| Парткод: | 024-12403-005 |
| Деталь: | *Stripper ADJ Arm |
| Парткод: | 024-12405-008 |
| Деталь: | *Plate Stripper Shaft Catch |
| Парткод: | 024-12406-004 |
| Деталь: | *Worm Gear Box Stripper Unit |
| Парткод: | 023-12409-200 |
| Деталь: | *Shaft Stripper Cam |
| Парткод: | 024-12404-206 |
| Деталь: | *ADJ.Dial Stripper |
| Парткод: | 023-12405-000 |
| Деталь: | *Assy ASY-CRG1-64(7-20) |
| Парткод: | 046-30069-004 |
| Деталь: | *Assy ASY-CR2-64(21-30) |
| Парткод: | 046-30044-001 |
| Деталь: | *Assy S-PLY-DRIVE(31-32) |
| Парткод: | 046-30070-002 |
| Деталь: | *Plastic Bearing RBB080160F |
| Парткод: | 045-30101-008 |
| Деталь: | *Pulley Ply-S1.5M-90-30 |
| Парткод: | 021-17575-007 |
| Деталь: | *Bracket K-BKT-MOT-S |
| Парткод: | 046-30045-008 |
| Деталь: | *Bracket BKT-MOT-64B |
| Парткод: | 046-30023-004 |
| Деталь: | *Motor Kh42Jm2B154 |
| Парткод: | 021-53201-008 |
| Деталь: | **Inverter Pws-Pxz170E4-B |
| Парткод: | 021-50536-106 |
| Деталь: | **Cover Inverter CVR-INV |
| Парткод: | 021-17558-102 |
| Деталь: | **Mylar Inverter Mlr-Inv |
| Парткод: | 021-17518-003 |
| Деталь: | **Slide Guide BUSH-SLIDE-64 |
| Парткод: | 046-30064-002 |
| Деталь: | **Reflector |
| Парткод: | 021-17556-002 |
| Деталь: | **Wire Harness CBP-LMP |
| Парткод: | 021-51123-000 |
| Деталь: | **Lamp Uxfl-08Yg37P2 |
| Парткод: | 021-53143-105 |
| Деталь: | **Slide Guide Slide-Bush Carriage |
| Парткод: | 021-17564-005 |
| Деталь: | *Pulley Ply-S1.5M-75 |
| Парткод: | 021-17574-000 |
| Деталь: | *Belt ST1116040 |
| Парткод: | 046-30019-007 |
| Деталь: | *Belt ST1173040 |
| Парткод: | 046-30024-000 |
| Деталь: | *Bracket Pulley BKT-DV |
| Парткод: | 021-17540-106 |
| Деталь: | *Shaft Pulley Sft-Dv |
| Парткод: | 021-17579-002 |
| Деталь: | *Bracket BKT-WIRE-HOLD |
| Парткод: | 021-17557-106 |
| Деталь: | *Pulley Dv-19-H5-W0.25 |
| Парткод: | 021-17582-100 |
| Деталь: | *Wire Front Wr-7X7-S-F |
| Парткод: | 021-17507-109 |
| Деталь: | *Wire Rear Wr-7X7-Z-R |
| Парткод: | 021-17508-105 |
| Деталь: | *Clip CLIP050140B |
| Парткод: | 046-30065-009 |
| Деталь: | *Washer WAS-082-120-050PW |
| Парткод: | 046-30066-005 |
| Деталь: | *Sponge SPNG-MIR2 |
| Парткод: | 046-30027-000 |
| Деталь: | Wire Harness FB Pulse Motor |
| Парткод: | 024-53057-006 |
| Деталь: | Wire Harness FB Upper |
| Парткод: | 046-53008-002 |
| Деталь: | Side Frame FL |
| Парткод: | 024-10001-007 |
| Деталь: | Channel F |
| Парткод: | 024-10021-202 |
| Деталь: | Side Frame FU |
| Парткод: | 024-10003-301 |
| Деталь: | Side Frame RL |
| Парткод: | 024-10002-100 |
| Деталь: | Channel RL |
| Парткод: | 024-10018-007 |
| Деталь: | Channel R |
| Парткод: | 024-10022-101 |
| Деталь: | Side Frame RU |
| Парткод: | 024-10004-200 |
| Деталь: | Bottom Stay |
| Парткод: | 024-10006-009 |
| Деталь: | RUBBER FOOT |
| Парткод: | 660-01015-002 |
| Деталь: | Sound Absorber (Bottom) |
| Парткод: | 024-10019-003 |
| Деталь: | Support Plate Handle |
| Парткод: | 024-10023-000 |
| Деталь: | Bottom Plate |
| Парткод: | 024-10017-105 |
| Деталь: | Stay Drum L |
| Парткод: | 024-10014-109 |
| Деталь: | Stay Bottom |
| Парткод: | 024-10016-004 |
| Деталь: | Stay Drum R |
| Парткод: | 024-10015-008 |
| Деталь: | Stay M-Removal L |
| Парткод: | 024-10024-007 |
| Деталь: | Stay M-Removal R |
| Парткод: | 024-10011-002 |
| Деталь: | Rail Stay |
| Парткод: | 024-10009-105 |
| Деталь: | Guide Plate Drum |
| Парткод: | 024-10030-007 |
| Деталь: | PF Stay |
| Парткод: | 024-10007-102 |
| Деталь: | Link Support Plate B |
| Парткод: | 024-10026-000 |
| Деталь: | Link Support Plate D |
| Парткод: | 024-10033-006 |
| Деталь: | Link Support Plate C |
| Парткод: | 024-10028-002 |
| Деталь: | Link Support Plate A |
| Парткод: | 024-10020-001 |
| Деталь: | Stay Scanner L |
| Парткод: | 024-10010-006 |
| Деталь: | Bracket Cover Left |
| Парткод: | 024-34019-004 |
| Деталь: | Stay Scanner C |
| Парткод: | 024-10012-106 |
| Деталь: | Stay Scanner R |
| Парткод: | 024-10013-005 |
| Деталь: | Reinforce Stay Scanner |
| Парткод: | 024-10032-000 |
| Деталь: | Bracket Cover |
| Парткод: | 024-10027-006 |
| Деталь: | Fixing Plate M-Removal |
| Парткод: | 024-10008-001 |
| Деталь: | Guide Plate Wire Harness |
| Парткод: | 024-10025-003 |
| Деталь: | Reinforce Plate Scanner |
| Парткод: | 024-10005-100 |
| Деталь: | Spacer Cover Rear L |
| Парткод: | 024-34030-008 |
| Деталь: | Spacer Cover Rear R |
| Парткод: | 024-34031-004 |
| Деталь: | STAY GUIDE PLATE |
| Парткод: | 023-12536-105 |
| Деталь: | Cover Guide Roller |
| Парткод: | 023-12542-105 |
| Деталь: | Noise Absober Guide Roller Cover |
| Парткод: | 023-12544-108 |
| Деталь: | Lower Cover Guide Plate |
| Парткод: | 023-12541-001 |
| Деталь: | Tray Support Plate R II |
| Парткод: | 024-21611-001 |
| Деталь: | Tray Support Plate F II |
| Парткод: | 024-21610-001 |
| Деталь: | Wire Saddle LWS-1316 |
| Парткод: | 665-02043-006 |
| Деталь: | Wire Saddle LWS-0711 |
| Парткод: | 665-02044-002 |
| Деталь: | FCR-45V0 |
| Парткод: | 665-00305-003 |
| Деталь: | SUPPORT PLATE COVER |
| Парткод: | 024-10034-002 |
| Деталь: | Suction Unit (1-45) |
| Парткод: | 024-75071-053 |
| Деталь: | *P.-E.Pulley Suction |
| Парткод: | 020-13116-205 |
| Деталь: | *Shaft Belt Driven Pulley |
| Парткод: | 023-21361-008 |
| Деталь: | *Flat Belt 15X0.65X482 |
| Парткод: | 629-00004-007 |
| Деталь: | *M Wing Front |
| Парткод: | 023-21322-002 |
| Деталь: | *S Wing Front |
| Парткод: | 023-21324-005 |
| Деталь: | *Wing Shaft |
| Парткод: | 024-21338-003 |
| Деталь: | *Spring Wing Front |
| Парткод: | 023-21328-000 |
| Деталь: | *Spring Wing Rear |
| Парткод: | 023-21332-008 |
| Деталь: | *M Wing Rear |
| Парткод: | 023-21321-006 |
| Деталь: | *S Wing Rear |
| Парткод: | 023-21323-009 |
| Деталь: | *Belt Roller Plate |
| Парткод: | 024-21309-003 |
| Деталь: | *Belt Roller |
| Парткод: | 024-21341-004 |
| Деталь: | *link Plate S Wing |
| Парткод: | 023-21329-104 |
| Деталь: | *link Plate M Wing |
| Парткод: | 023-21331-001 |
| Деталь: | *Bearing Flaw678 ZZA |
| Парткод: | 600-50057-006 |
| Деталь: | *Drive Shaft Suction |
| Парткод: | 024-21306-004 |
| Деталь: | *Roller (Inner) Transfer Belt |
| Парткод: | 030-15249-004 |
| Деталь: | *Pulley P18S2M6 |
| Парткод: | 611-90016-004 |
| Деталь: | *Belt 116-S2M-40 |
| Парткод: | 621-00004-009 |
| Деталь: | *Bracket Motor-S |
| Парткод: | 024-21312-004 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | *Suction Motor Ccwrs-55PH |
| Парткод: | 024-74008-056 |
| Деталь: | **MetalSlit Motor |
| Парткод: | 023-21342-003 |
| Деталь: | *Pulley Gear 0.8X45+28S2M |
| Парткод: | 613-10005-001 |
| Деталь: | *Wire Harness EJ Motor |
| Парткод: | 024-21701-000 |
| Деталь: | *Wire Harness EJ Sensor |
| Парткод: | 024-21702-007 |
| Деталь: | *Fan D12F-24PLH1C13 |
| Парткод: | 490-41013-000 |
| Деталь: | *Base Wing Drive |
| Парткод: | 024-21325-009 |
| Деталь: | *Worm gear M1x12x1 |
| Парткод: | 612-50005-007 |
| Деталь: | *Wing Shaft Suction |
| Парткод: | 023-21411-005 |
| Деталь: | *Metal F6X10/9X6:12 X 1.5 |
| Парткод: | 607-13000-402 |
| Деталь: | *Gear M0.5x21x6 |
| Парткод: | 612-10035-000 |
| Деталь: | *Motor PM42L-048-ZVS6 |
| Парткод: | 490-33015-002 |
| Деталь: | *W cam shaft Wing |
| Парткод: | 023-21410-009 |
| Деталь: | *MW cam Wing |
| Парткод: | 023-21408-004 |
| Деталь: | *Helical gear M1x16x6 |
| Парткод: | 612-30001-005 |
| Деталь: | *SW cam Wing |
| Парткод: | 023-21409-108 |
| Деталь: | *Bracket P-Ejection Sensor |
| Парткод: | 024-21303-005 |
| Деталь: | *GP2A200LCS |
| Парткод: | 444-33000-002 |
| Деталь: | *Junction Harness EJ Sensor |
| Парткод: | 024-21703-003 |
| Деталь: | *Suction Base |
| Парткод: | 024-21300-006 |
| Деталь: | *Feed Plate F |
| Парткод: | 024-21333-001 |
| Деталь: | *Suction Plate |
| Парткод: | 024-21302-009 |
| Деталь: | *Feed Plate R |
| Парткод: | 024-21334-008 |
| Деталь: | *SU Plate EJ |
| Парткод: | 024-21318-002 |
| Деталь: | *Wire Saddle L |
| Парткод: | 665-21801-008 |
| Деталь: | Cover P-Ejection |
| Парткод: | 024-21320-007 |
| Деталь: | De-Electricity Brush |
| Парткод: | 017-13258-004 |
| Деталь: | Seal Folding Tray Ins |
| Парткод: | 023-21801-008 |
| Деталь: | Bracket P-EJ Cover F |
| Парткод: | 024-21321-100 |
| Деталь: | Bracket P-EJ Cover |
| Парткод: | 024-21322-107 |
| Деталь: | Fixing Pin |
| Парткод: | 020-13114-105 |
| Деталь: | Wire Harness Rear Lower A |
| Парткод: | 024-53011-103 |
| Деталь: | P-Eject Plate |
| Парткод: | 024-21324-002 |
| Деталь: | Unit/Stage Cover (1-5) |
| Парткод: | 023-75113-050 |
| Деталь: | *Stage Cover |
| Парткод: | 023-30008-000 |
| Деталь: | *Frame Stage Cover |
| Парткод: | 023-30007-004 |
| Деталь: | *Original Holder Cover (Upper) Stage Cover |
| Парткод: | 018-16411-200 |
| Деталь: | *Actuator Plate Stage cover Actuator |
| Парткод: | 023-30006-008 |
| Деталь: | *Stage Cover Hinge Assy 3 |
| Парткод: | 023-30070-008 |
| Деталь: | Stage Pad 2 Stage Cover |
| Парткод: | 023-30075-000 |
| Деталь: | *Frame Panel MZ |
| Парткод: | 024-37101-100 |
| Деталь: | *Sheet Panel Mode Key Pic |
| Парткод: | 024-37403-000 |
| Деталь: | *Sheet Panel Mode Key Eng |
| Парткод: | 024-37405-002 |
| Деталь: | *Sheet Panel Mode Key Ch |
| Парткод: | 024-37407-005 |
| Деталь: | *Sheet Print Control Pic |
| Парткод: | 024-37404-006 |
| Деталь: | *Sheet Print Control Eng |
| Парткод: | 024-37406-009 |
| Деталь: | *Sheet Print Control Ch |
| Парткод: | 024-37403-001 |
| Деталь: | *Wake-Up Key |
| Парткод: | 024-37327-001 |
| Деталь: | *Reset Key Pic |
| Парткод: | 024-37334-008 |
| Деталь: | *Reset Key Eng |
| Парткод: | 024-37338-003 |
| Деталь: | *Reset Key Ch |
| Парткод: | 024-37342-108 |
| Деталь: | *Stop Key Pic |
| Парткод: | 024-37332-005 |
| Деталь: | *Stop Key Eng |
| Парткод: | 024-37336-000 |
| Деталь: | *Stop Key Ch |
| Парткод: | 024-37340-105 |
| Деталь: | *Mode Test Print Key Pic |
| Парткод: | 024-37333-001 |
| Деталь: | *Mode Test Print Key Eng |
| Парткод: | 024-37337-007 |
| Деталь: | *Mode Test Print Key Ch |
| Парткод: | 024-37341-101 |
| Деталь: | *Start Key Pic |
| Парткод: | 024-37331-009 |
| Деталь: | *Start Key Eng |
| Парткод: | 024-37335-004 |
| Деталь: | *Start Key Ch |
| Парткод: | 024-37339-204 |
| Деталь: | *Print Control Key |
| Парткод: | 024-37326-005 |
| Деталь: | *Center Button |
| Парткод: | 024-37328-008 |
| Деталь: | *Print Position Control Key |
| Парткод: | 024-37329-004 |
| Деталь: | *Ten Key Button |
| Парткод: | 024-37323-006 |
| Деталь: | *Sealed Mylar A MZ |
| Парткод: | 024-37202-004 |
| Деталь: | *Main-SW-PCB MZ |
| Парткод: | 024-37201-008 |
| Деталь: | *LCD Ground Wire MZ |
| Парткод: | 024-37205-003 |
| Деталь: | *Cover Panel MZ |
| Парткод: | 024-37102-000 |
| Деталь: | *Display Mode Key Pic |
| Парткод: | 023-37110-005 |
| Деталь: | *Display Mode Key Eng |
| Парткод: | 023-37109-007 |
| Деталь: | *Display Mode Key Ch |
| Парткод: | 023-37111-001 |
| Деталь: | *Shield Mylar Sheet B RZ5 Mode Key |
| Парткод: | 023-37129-008 |
| Деталь: | *MODE-KEY-PCB |
| Парткод: | 023-37137-000 |
| Деталь: | *Segment Cover |
| Парткод: | 024-37104-002 |
| Деталь: | *LCD Control Unit |
| Парткод: | 023-43775-205 |
| Деталь: | Wire Harness Panel |
| Парткод: | 024-53050-001 |
| Деталь: | Bracket Front Door SW Assy |
| Парткод: | 024-34022-005 |
| Деталь: | Spring Switch |
| Парткод: | 021-11318-002 |
| Деталь: | Plate Switch |
| Парткод: | 021-11317-006 |
| Деталь: | Micro SW AM50031A431F1 |
| Парткод: | 444-10003-004 |
| Деталь: | PS Switch Assy |
| Парткод: | 024-53008-005 |
| Деталь: | Wire Harness PS Switch |
| Парткод: | 024-53005-006 |
| Деталь: | Bracket Main Drive PCB R |
| Парткод: | 024-50019-006 |
| Деталь: | Bracket Main Drive PCB L |
| Парткод: | 024-50018-000 |
| Деталь: | MM-DRIVE-PCB |
| Парткод: | 024-50503-102 |
| Деталь: | Wire Harness FL Motor |
| Парткод: | 024-53036-009 |
| Деталь: | Wire Harness Front Upper |
| Парткод: | 024-53035-002 |
| Деталь: | Bracket Counter |
| Парткод: | 024-50015-000 |
| Деталь: | COUNTER |
| Парткод: | 492-00001-108 |
| Деталь: | Bracket RF PCB |
| Парткод: | 024-50022-007 |
| Деталь: | RFRW-PCB 3Ch |
| Парткод: | 045-50025-308 |
| Деталь: | Wire Harness D-Drawer H |
| Парткод: | 024-53030-108 |
| Деталь: | Wire Harness D-Drawer H U |
| Парткод: | 024-53031-007 |
| Деталь: | Wire Harness D-Drawer Junction H |
| Парткод: | 024-53026-003 |
| Деталь: | Wire Saddle LWS-0711 |
| Парткод: | 665-02044-002 |
| Деталь: | Edging Saddle TSB-1909L |
| Парткод: | 665-04068-006 |
| Деталь: | Square bushing |
| Парткод: | 665-04002-005 |
| Деталь: | Square Bushing SB-2718 |
| Парткод: | 665-04054-005 |
| Деталь: | Paper Receive Tray Unit (1-26) |
| Парткод: | 024-75098-059 |
| Деталь: | *Flap P.-Rcv.-T. Assy (11-14) |
| Парткод: | 023-75147-052 |
| Деталь: | *Back Stopper P.-RCV.-T |
| Парткод: | 023-21608-003 |
| Деталь: | *Fence Cushion |
| Парткод: | 018-33151-203 |
| Деталь: | *Shaft Fence |
| Парткод: | 023-21634-004 |
| Деталь: | *Slide Base P.Rcv.-T. |
| Парткод: | 023-21635-000 |
| Деталь: | *Slide Plate(Upper) P.-R T. |
| Парткод: | 023-21637-003 |
| Деталь: | *Plate Spring P.-Rcv.-T |
| Парткод: | 023-21638-000 |
| Деталь: | *Slide Plate(Lower) P.-Rcv.-T. |
| Парткод: | 023-21636-007 |
| Деталь: | *Lever Paper Guide P.-Rcv.-T. |
| Парткод: | 023-21621-000 |
| Деталь: | *Paper Guide R P.-Rcv.-T. |
| Парткод: | 023-21607-201 |
| Деталь: | *Paper Guide F P.-Rcv.-T. |
| Парткод: | 023-21606-205 |
| Деталь: | **Flap Cover P.-Rcv.-T. |
| Парткод: | 023-21614-003 |
| Деталь: | **Holder Flap P.Rcv.-T |
| Парткод: | 023-21615-204 |
| Деталь: | **Flap P.-Rcv.-T |
| Парткод: | 023-21612-000 |
| Деталь: | **Balancer Flap P.-RCV.-T. |
| Парткод: | 023-21613-007 |
| Деталь: | *Slide Rail Paper Guide P.-Rcv.-T. |
| Парткод: | 023-21639-006 |
| Деталь: | *Slide Rail Paper Stopper P.-Rcv.-T. |
| Парткод: | 023-21640-004 |
| Деталь: | *Tray Side Plate R |
| Парткод: | 024-21602-002 |
| Деталь: | *Tray Side Plate F |
| Парткод: | 024-21601-006 |
| Деталь: | *Ground Plate Slide Rail P.Rcv.-T. |
| Парткод: | 023-21633-008 |
| Деталь: | *Paper Receiving Tray |
| Парткод: | 023-21601-106 |
| Деталь: | *Seal P.-Pcv.-T:Folding Pic |
| Парткод: | 023-21802-004 |
| Деталь: | *Bracket Magnet Catch P.-Rcv.-T. |
| Парткод: | 023-21643-003 |
| Деталь: | *Magnet Catch SM-50P |
| Парткод: | 660-05000-018 |
| Деталь: | *Seal Fence Adj-F |
| Парткод: | 024-21802-001 |
| Деталь: | *Seal Fence Adj-R |
| Парткод: | 024-21803-008 |
| Деталь: | *Seal Fence Adj-C |
| Парткод: | 024-21804-004 |
| Деталь: | Master Making Unit (Fig22-Fig24) |
| Парткод: | 024-75092-050 |
| Деталь: | *M-M Upper Unit Assy (1-7,9-12,14-26,43-63 |
| Парткод: | 024-75086-050 |
| Деталь: | *TPH Assy A3 (28-31,34-42) |
| Парткод: | 023-75073-156 |
| Деталь: | *TPH Assy A3 H(28-31,34-42) |
| Парткод: | 045-75307-154 |
| Деталь: | **Frame M-M Upper Unit |
| Парткод: | 023-28150-207 |
| Деталь: | **Shaft Handle M-M Up |
| Парткод: | 023-28157-007 |
| Деталь: | **Hook Lever M.-M Up |
| Парткод: | 023-28236-004 |
| Деталь: | **Hook M.-M Up |
| Парткод: | 023-28237-000 |
| Деталь: | **Hook Spring M.-M Up |
| Парткод: | 023-28356-000 |
| Деталь: | **Pushing Plate R Set-Guide Plate |
| Парткод: | 023-28253-103 |
| Деталь: | **Spring Hook Bracket Rear TPH Pressure |
| Парткод: | 023-28152-005 |
| Деталь: | *Spring Rear M.-M Up |
| Парткод: | 023-28156-000 |
| Деталь: | **Pivot Support Plate Rear M.-M Up |
| Парткод: | 023-28252-107 |
| Деталь: | **Pivot Shaft M-M Unit |
| Парткод: | 024-28175-002 |
| Деталь: | **Pushing Plate F Set-Guide Plate |
| Парткод: | 023-28215-201 |
| Деталь: | **Bracket Front TPH Pressure spring |
| Парткод: | 023-28381-004 |
| Деталь: | *Spring Front M.-M Up |
| Парткод: | 023-28155-004 |
| Деталь: | **Pivot Support Plate Front M.-M Up |
| Парткод: | 023-28151-106 |
| Деталь: | **Seal Master Making Unit |
| Парткод: | 023-28426-105 |
| Деталь: | **Upper Bracket A3 Master End Sensor |
| Парткод: | 023-28418-005 |
| Деталь: | **light Absorber Strip (21X15) |
| Парткод: | 023-28431-001 |
| Деталь: | **Cover Master End Sensor |
| Парткод: | 023-28427-004 |
| Деталь: | **Sensor (Rcv) KH0854-01 |
| Парткод: | 444-42030-003 |
| Деталь: | **Bottom Cover TPH M.-M. |
| Парткод: | 023-28162-000 |
| Деталь: | **De-Electricity Brush A3 |
| Парткод: | 023-28410-004 |
| Деталь: | **Pivot Shaft TPH |
| Парткод: | 023-28158-100 |
| Деталь: | **Pressure Release Plate TPH Press |
| Парткод: | 023-28160-008 |
| Деталь: | **Pressure Lever Bracket M.-M Up |
| Парткод: | 023-28159-301 |
| Деталь: | **TPH Pressure Spring 40 |
| Парткод: | 023-28161-004 |
| Деталь: | **TPH Alignment Shaft |
| Парткод: | 023-28173-100 |
| Деталь: | *Metal F10X14X10 18X2 |
| Парткод: | 607-10008-003 |
| Деталь: | **TPH holder TA3 |
| Парткод: | 023-28174-203 |
| Деталь: | **TPH Pressure Assist Plate A3 |
| Парткод: | 023-28413-003 |
| Деталь: | **TPH Boss |
| Парткод: | 023-28412-104 |
| Деталь: | **Protection Plate TPH connector TA3 |
| Парткод: | 023-28315-001 |
| Деталь: | *Spring TPH Alignment Shaft |
| Парткод: | 023-28435-007 |
| Деталь: | *Lock Ring |
| Парткод: | 019-11812-106 |
| Деталь: | **Stepped Screw F6x7.2 M3x4 |
| Парткод: | 635-10005-009 |
| Деталь: | **TPH 303R11 |
| Парткод: | 444-80001-106 |
| Деталь: | **TPH 303R14 |
| Парткод: | 045-28006-006 |
| Деталь: | **Plate T-Rear TPH |
| Парткод: | 023-28021-008 |
| Деталь: | **Plate T-Front TPH |
| Парткод: | 023-28022-004 |
| Деталь: | **Bracket TPH Brush TA3 |
| Парткод: | 023-28175-005 |
| Деталь: | **De-electricity Brush TPH A3 |
| Парткод: | 023-28411-000 |
| Деталь: | **Holding roller TA3 |
| Парткод: | 023-28024-007 |
| Деталь: | **Metal F8x10x3 11.2x0.6 |
| Парткод: | 607-10005-004 |
| Деталь: | **Ground Wire U3-55-R3 |
| Парткод: | 488-90030-109 |
| Деталь: | **Metal F8X12X7 16X1.5 |
| Парткод: | 607-15007-005 |
| Деталь: | **Bracket TPH pressure motor |
| Парткод: | 023-28168-009 |
| Деталь: | **Cam TPH Pressure |
| Парткод: | 023-28165-000 |
| Деталь: | **Gear M1X20X6 |
| Парткод: | 612-10010-008 |
| Деталь: | **Shaft TPH Pressure Cam |
| Парткод: | 023-28166-006 |
| Деталь: | **Metal F6X10/9X6:12 X 1.5 |
| Парткод: | 607-13000-402 |
| Деталь: | **Pressure Detection Plate TPH |
| Парткод: | 023-28361-003 |
| Деталь: | **Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | **Shaft Gear TPH lift Motor |
| Парткод: | 023-28213-004 |
| Деталь: | **Gear M0.8X25+M0.8X14 |
| Парткод: | 612-80006-008 |
| Деталь: | **Shaft Gear 8 TPH lift Motor |
| Парткод: | 023-28433-004 |
| Деталь: | **Gear M0.8X25+M1X14 |
| Парткод: | 612-80007-004 |
| Деталь: | **Gear M0.8X20+M0.8X14 |
| Парткод: | 612-80008-000 |
| Деталь: | **Motor Assy (CWRS-445PA) |
| Парткод: | 023-75906-077 |
| Деталь: | **Support Clamp Worm |
| Парткод: | 030-19205-001 |
| Деталь: | **Holding Plate Worm Gear |
| Парткод: | 023-28172-006 |
| Деталь: | **Wire Harness TPH |
| Парткод: | 024-28503-000 |
| Деталь: | **Wire Harness TPH 2H |
| Парткод: | 024-28512-009 |
| Деталь: | **Gear Cover M.-M UP |
| Парткод: | 023-28328-103 |
| Деталь: | **Seal TPH Cleaning Pic. |
| Парткод: | 023-28942-103 |
| Деталь: | Seal TPH Pic |
| Парткод: | 023-28423-009 |
| Деталь: | Seal TPH Eng. |
| Парткод: | 023-28424-005 |
| Деталь: | **Wire Saddle LWS-1316 |
| Парткод: | 665-02043-006 |
| Деталь: | Mid Feed Unit (1-33) |
| Парткод: | 024-75094-053 |
| Деталь: | *Mid Feed Base |
| Парткод: | 024-55011-003 |
| Деталь: | *Mid Feed Plate |
| Парткод: | 024-55005-003 |
| Деталь: | *Stopper Feed Plate |
| Парткод: | 024-55009-009 |
| Деталь: | *Spring Flapper Open F |
| Парткод: | 024-55014-002 |
| Деталь: | *Flap Rack |
| Парткод: | 024-55508-005 |
| Деталь: | *Stepped Screw F4X7 M3X4 |
| Парткод: | 635-17473-008 |
| Деталь: | *Flap-Cam Gear |
| Парткод: | 024-55509-001 |
| Деталь: | *Sensor GP2A25S |
| Парткод: | 443-32005-003 |
| Деталь: | *Wire Harness M-Feed Sensor |
| Парткод: | 024-55802-000 |
| Деталь: | *Bearing Flaw678 ZZA |
| Парткод: | 600-50057-006 |
| Деталь: | *Lock Plate Guide Roller |
| Парткод: | 023-12519-006 |
| Деталь: | *Coupling |
| Парткод: | 024-55015-009 |
| Деталь: | *Drive Shaft Mid |
| Парткод: | 024-55008-002 |
| Деталь: | *Shaft Driven |
| Парткод: | 024-55010-007 |
| Деталь: | *Roller (Inner) Transfer Belt |
| Парткод: | 030-15249-004 |
| Деталь: | *Flat Belt 15X0.65X303 |
| Парткод: | 629-00003-000 |
| Деталь: | *Bearing Flaw BC6-12ZZA |
| Парткод: | 600-50046-004 |
| Деталь: | *Spring Flapper Open R |
| Парткод: | 024-55018-008 |
| Деталь: | *Flap |
| Парткод: | 024-55006-000 |
| Деталь: | *Stepped Screw 6X2.2 M4X2.5 |
| Парткод: | 635-17624-006 |
| Деталь: | *Suction Box |
| Парткод: | 024-55030-008 |
| Деталь: | *Wire Harness Mid Feed U |
| Парткод: | 024-55801-004 |
| Деталь: | *Flap Base Plate |
| Парткод: | 024-55500-004 |
| Деталь: | *Gear Mx0.8X22+M0.8X15 |
| Парткод: | 612-80020-000 |
| Деталь: | *Gear Mx0.8X26+M0.8X15 |
| Парткод: | 612-80021-007 |
| Деталь: | *Gear Main Cam |
| Парткод: | 024-55511-006 |
| Деталь: | *Flap Lever |
| Парткод: | 024-55506-002 |
| Деталь: | *Flap Spring |
| Парткод: | 024-55507-009 |
| Деталь: | *Wire Saddle LWS-0711 |
| Парткод: | 665-02044-002 |
| Деталь: | *Fan D12F-24PLH1C13 |
| Парткод: | 490-41013-000 |
| Деталь: | *Bracket Motor |
| Парткод: | 024-55510-000 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | Suction Plate Mid |
| Парткод: | 024-55004-007 |
| Деталь: | Fixing Pin |
| Парткод: | 020-13114-105 |
| Деталь: | Fixed Shaft Mid |
| Парткод: | 024-55001-008 |
| Деталь: | SPRING COUPLING |
| Парткод: | 024-55017-001 |
| Деталь: | SHAFT COUPLING |
| Парткод: | 024-55013-006 |
| Деталь: | Metal F8X13/12X5 16X2 |
| Парткод: | 607-15000-000 |
| Деталь: | Fixed Plate Drive Joint |
| Парткод: | 024-55002-004 |
| Деталь: | Lever Joint Release |
| Парткод: | 024-55016-005 |
| Деталь: | Gear M1X14 |
| Парткод: | 612-10030-009 |
| Деталь: | Wire Harness Mid Feed H |
| Парткод: | 024-53027-000 |
| Деталь: | *Motor Assy (CWRS-445PA) |
| Парткод: | 023-75906-077 |
| Деталь: | Scanner Unit 600Inch (Fig19_1-5,13-41,Fig 20 |
| Парткод: | 024-30903-309 |
| Деталь: | Scanner Unit 600M (Fig19_1-5,13-41,Fig 20_1 |
| Парткод: | 024-30902-604 |
| Деталь: | *Blind Cover Guide |
| Парткод: | 021-17568-108 |
| Деталь: | *Sponge Blind Cover Guide |
| Парткод: | 021-75014-007 |
| Деталь: | *Screw Scr-M3-1.6 |
| Парткод: | 021-17525-000 |
| Деталь: | *Adj. Plate PLT-ADJ-GLASS |
| Парткод: | 021-17545-108 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | SPRING ACTUATOR |
| Парткод: | 021-17129-104 |
| Деталь: | Actuator 2 Scanner |
| Парткод: | 023-30073-007 |
| Деталь: | Bracket Stage cover closing sensor |
| Парткод: | 023-30071-004 |
| Деталь: | Bracket FB Scanner |
| Парткод: | 023-30003-009 |
| Деталь: | SB-6025 |
| Парткод: | 665-04055-001 |
| Деталь: | Square Bushing SB-2718 |
| Парткод: | 665-04054-005 |
| Деталь: | Hinge Bracket Flat Bed |
| Парткод: | 023-30002-002 |
| Деталь: | *Frame Frm-Upper Scanner |
| Парткод: | 021-17538-209 |
| Деталь: | *Sponge Spng-Pg-1 |
| Парткод: | 021-17515-004 |
| Деталь: | *Sponge Spng-Pg-2 |
| Парткод: | 021-17516-000 |
| Деталь: | *Tape-Frm-U Scanner |
| Парткод: | 021-17585-002 |
| Деталь: | *Mylar Mlr-Frame-U Scanner |
| Парткод: | 021-17514-008 |
| Деталь: | *Fixing Plate Spr-Glass-R |
| Парткод: | 021-17531-107 |
| Деталь: | *Fixing Plate Spr-Glass-F |
| Парткод: | 021-17530-100 |
| Деталь: | *Stage Glass Gls-Platen |
| Парткод: | 021-17510-207 |
| Деталь: | *Shading Plate E-20 |
| Парткод: | 021-17512-005 |
| Деталь: | *Cover CVR-LENS-UNIT |
| Парткод: | 021-17553-003 |
| Деталь: | *ASM-APS-Sensor-M |
| Парткод: | 024-30008-008 |
| Деталь: | *Sensor Ey3A-1061 |
| Парткод: | 021-53142-001 |
| Деталь: | *Harness ASM-Size Sensor-M |
| Парткод: | 024-30009-004 |
| Деталь: | *CCD Unit PBA 600 |
| Парткод: | 024-30003-006 |
| Деталь: | *Flat Cable ASM-Main I/F 600 |
| Парткод: | 024-30007-001 |
| Деталь: | *Plate-APS-Sensor |
| Парткод: | 021-17543-008 |
| Деталь: | *Harness Empty Sensor |
| Парткод: | 021-51122-003 |
| Деталь: | *Plate Plt-Ccd-Cable Scanner |
| Парткод: | 021-17544-004 |
| Деталь: | *Guide Bracket Guide-Ffc-Frame |
| Парткод: | 021-17569-007 |
| Деталь: | *Sponge Spng-Ccd-Cable |
| Парткод: | 021-17517-007 |
| Деталь: | *Guide Plate Plt-Ccd-Cable2 |
| Парткод: | 021-17547-003 |
| Деталь: | *Bracket HP-SENS Scanner |
| Парткод: | 021-17567-004 |
| Деталь: | *Wire Harness ASM-H.Psens |
| Парткод: | 021-51121-007 |
| Деталь: | *PCB Pba-Chukei |
| Парткод: | 021-50535-002 |
| Деталь: | *Plate Plt-Hinge Scanner |
| Парткод: | 021-17546-007 |
| Деталь: | Wire Harness Rear Upper |
| Парткод: | 024-53010-107 |
| Деталь: | Wire Harness Rear Sensor U |
| Парткод: | 024-53019-007 |
| Деталь: | Scanner Unit 600M II (Fig 18, Fig 19) |
| Парткод: | 045-97000-001 |
| Деталь: | Scanner Unit 600HB (Fig 18, Fig 19) |
| Парткод: | 045-97001-008 |
| Деталь: | *Blind Cover Guide |
| Парткод: | 021-17568-108 |
| Деталь: | *Sponge Blind Cover Guide |
| Парткод: | 021-75014-007 |
| Деталь: | *Screw Scr-M3-1.6 |
| Парткод: | 021-17525-000 |
| Деталь: | *Adj. Plate PLT-ADJ-GLASS |
| Парткод: | 021-17545-205 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-100 |
| Деталь: | *Spring Actuator |
| Парткод: | 021-17129-104 |
| Деталь: | *Actuator 2 Scanner |
| Парткод: | 023-30073-007 |
| Деталь: | *Bracket Stage cover closing sensor |
| Парткод: | 023-30071-004 |
| Деталь: | Bracket FB Scanner |
| Парткод: | 023-30003-009 |
| Деталь: | Hinge Bracket Flat Bed |
| Парткод: | 024-30002-107 |
| Деталь: | *Frame Frm-Upper Scanner |
| Парткод: | 021-17538-306 |
| Деталь: | *Sponge Spng-Pg-1 |
| Парткод: | 021-17515-004 |
| Деталь: | *Sponge Spng-Pg-2 |
| Парткод: | 021-17516-000 |
| Деталь: | *Tape-Frm-U Scanner |
| Парткод: | 021-17585-002 |
| Деталь: | *Mylar Mlr-Frame-U Scanner |
| Парткод: | 021-17514-008 |
| Деталь: | *Sponge Spr-Glass-R |
| Парткод: | 021-17531-107 |
| Деталь: | *Sponge Spr-Glass-F |
| Парткод: | 021-17530-100 |
| Деталь: | *Stage Glass Gls-Platen |
| Парткод: | 021-17510-207 |
| Деталь: | *Shading Plate E-20 |
| Парткод: | 021-17512-005 |
| Деталь: | *Cover CVR-LENS-UNIT |
| Парткод: | 021-17553-003 |
| Деталь: | *ASM-APS-Sensor-M |
| Парткод: | 024-30008-008 |
| Деталь: | *Sensor Ey3A-1061 |
| Парткод: | 021-53142-001 |
| Деталь: | *Harness ASM-Size Sensor-M |
| Парткод: | 024-30009-101 |
| Деталь: | *Harness ASM-SISESENS-MI |
| Парткод: | 024-30010-207 |
| Деталь: | *CCD Unit PBA 600M |
| Парткод: | 045-50008-004 |
| Деталь: | *Band Lens Assy |
| Парткод: | 021-17592-106 |
| Деталь: | *Lens Assy |
| Парткод: | 045-30100-001 |
| Деталь: | *Cover Lens Assy |
| Парткод: | 021-17593-102 |
| Деталь: | *Flat Cable ASM-Main I/F 600 |
| Парткод: | 024-30007-001 |
| Деталь: | *Plate-APS-Sensor |
| Парткод: | 021-17543-105 |
| Деталь: | *Harness Empty Sensor |
| Парткод: | 021-51122-100 |
| Деталь: | *Plate Plt-Ccd-Cable Scanner |
| Парткод: | 021-17544-101 |
| Деталь: | *Guide Bracket Guide-Ffc-Frame |
| Парткод: | 021-17569-007 |
| Деталь: | *Sponge Spng-Ccd-Cable |
| Парткод: | 021-17517-007 |
| Деталь: | *Guide Plate Plt-Ccd-Cable2 |
| Парткод: | 021-17547-100 |
| Деталь: | Bracket Flat Cable Guide |
| Парткод: | 045-30008-008 |
| Деталь: | FFC Clamp FC-45 |
| Парткод: | 665-00310-007 |
| Деталь: | *Bracket HP-SENS Scanner |
| Парткод: | 021-17567-004 |
| Деталь: | *Wire Harness ASM-H.Psens |
| Парткод: | 021-51121-007 |
| Деталь: | *PCB Pba-Chukei |
| Парткод: | 021-50535-100 |
| Деталь: | *Plate Plt-Hinge Scanner |
| Парткод: | 021-17546-104 |
| Деталь: | Wire Harness FB Upper |
| Парткод: | 045-53001-000 |
| Деталь: | MECHA-CNTL-PCB SU |
| Парткод: | 024-75000-059 |
| Деталь: | Wire Harness Rear Upper |
| Парткод: | 024-53010-107 |
| Деталь: | Wire Harness MRV1 Joint |
| Парткод: | 024-53016-105 |
| Деталь: | Wire Harness Rear Lower B |
| Парткод: | 024-53012-100 |
| Деталь: | Wire Harness Rear Lower A |
| Парткод: | 024-53011-103 |
| Деталь: | SS-15N (170mm) |
| Парткод: | 665-03001-005 |
| Деталь: | MM-DRIVE-PCB |
| Парткод: | 024-50503-102 |
| Деталь: | Wire Harness Main FG2 |
| Парткод: | 024-53038-001 |
| Деталь: | Wire Harness D-Drawer Junction H |
| Парткод: | 024-53026-003 |
| Деталь: | Wire Harness D-Drawer Junction H U |
| Парткод: | 024-53056-000 |
| Деталь: | Wire Harness MRV2 Joint |
| Парткод: | 024-53037-005 |
| Деталь: | Wire Harness FL Motor |
| Парткод: | 024-53036-009 |
| Деталь: | Wire Harness Drive PS |
| Парткод: | 024-53006-002 |
| Деталь: | Wire Harness Main Motor |
| Парткод: | 024-53039-008 |
| Деталь: | Wire Harness F-Safety SW |
| Парткод: | 024-53034-006 |
| Деталь: | *Washer WAS-082-120-050PW |
| Парткод: | - |
| Деталь: | *Pulley Ply-S1.5M-90-30 |
| Парткод: | 021-17575-007 |
| Деталь: | *Bracket K-BKT-M Scanner |
| Парткод: | 021-17505-203 |
| Деталь: | *Bracket FB Pulse Motor BK OT |
| Парткод: | 021-17541-102 |
| Деталь: | *Motor Kh42Jm2B154 |
| Парткод: | 021-53201-008 |
| Деталь: | *Wire Harness FB Pulse Mo r |
| Парткод: | 045-53014-005 |
| Деталь: | *Frame Assy-Frame-Lower |
| Парткод: | 021-17501-208 |
| Деталь: | *Frame Carriage 1 Frm-Cr1 |
| Парткод: | 021-17554-107 |
| Деталь: | *Inverter Pws-Pxz170E4-B |
| Парткод: | 021-50536-106 |
| Деталь: | *Cover Inverter CVR-INV |
| Парткод: | 021-17558-102 |
| Деталь: | *Mylar Inverter Mlr-Inv |
| Парткод: | 021-17518-003 |
| Деталь: | *Mirror Carriage 1 Mir-1 |
| Парткод: | 021-17509-004 |
| Деталь: | *Adj. Bracket Rear BKT-ADJ-CR1 |
| Парткод: | 021-17555-103 |
| Деталь: | *Plate Spring Mirror 1 Spr-Mir-1 |
| Парткод: | 021-17528-009 |
| Деталь: | *Sponge Mirror 1 Spng-Mir |
| Парткод: | 021-17589-008 |
| Деталь: | *Adj. Bracket Front BKT-ADJ-CR1-F |
| Парткод: | 021-17559-109 |
| Деталь: | *Slide Guide Sllde-Bush Carriage |
| Парткод: | 021-17564-005 |
| Деталь: | *Guide Bracket Guide-Ffc-Cr1 |
| Парткод: | 021-17570-005 |
| Деталь: | *Reflector |
| Парткод: | 021-17556-002 |
| Деталь: | *Wire Harness Assy-Ffc |
| Парткод: | 021-51120-000 |
| Деталь: | *Lamp Uxfl-08Yg37P2 |
| Парткод: | 021-53143-105 |
| Деталь: | *Frame Carriage 2 Frm-Cr2 |
| Парткод: | 021-17560-107 |
| Деталь: | *Bracket F BKT-SllDE-CR2-F |
| Парткод: | 021-17561-103 |
| Деталь: | *Mirror 2 Carriage 2 |
| Парткод: | 021-17581-007 |
| Деталь: | *Support Shaft Sft-Cr2 Carriage 2 |
| Парткод: | 021-17523-007 |
| Деталь: | *Bracket Rear Pulley K-DV-R |
| Парткод: | 021-17506-102 |
| Деталь: | *Pulley Dv-19-H5-W0.25 |
| Парткод: | 021-17582-003 |
| Деталь: | *Guide Pulley Ply-Turn |
| Парткод: | 021-17565-001 |
| Деталь: | *Bracket Front Pulley BKT-DV-CR2-F |
| Парткод: | 021-17562-207 |
| Деталь: | *Pulley Drive Shaft Ply-Drive |
| Парткод: | 021-17521-101 |
| Деталь: | *Wire Front Wr-7X7-S-F |
| Парткод: | 021-17507-109 |
| Деталь: | *Wire Rear Wr-7X7-Z-R |
| Парткод: | 021-17508-105 |
| Деталь: | *Pulley Ply-S1.5M-75 |
| Парткод: | 021-17574-000 |
| Деталь: | *Belt ST1116060 |
| Парткод: | 021-17584-006 |
| Деталь: | *Belt ST1173060 |
| Парткод: | 021-17583-000 |
| Деталь: | *Bracket Pulley BKT-DV |
| Парткод: | 021-17540-106 |
| Деталь: | *Shaft Pulley Sft-Dv |
| Парткод: | 021-17579-002 |
| Деталь: | *Bracket BKT-WIRE-HOLD |
| Парткод: | 021-17557-106 |
| Деталь: | *Plate Spring Spr-Mir-2 |
| Парткод: | 021-17529-005 |
| Деталь: | Wire Harness FB Upper |
| Парткод: | 045-53001-000 |
| Деталь: | *Side M-Removal Plate R2 |
| Парткод: | 024-25032-006 |
| Деталь: | *Side M-Removal Plate F2 |
| Парткод: | 024-25020-008 |
| Деталь: | *Stay M-Removal A2 |
| Парткод: | 024-25043-008 |
| Деталь: | *Bracket Vertical FG Sensor 2 |
| Парткод: | 024-25077-000 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | *Wire Removal Feed FG2 |
| Парткод: | 024-25104-007 |
| Деталь: | *Stay M-Removal B2 |
| Парткод: | 024-25041-005 |
| Деталь: | *Compression Plate |
| Парткод: | 024-24099-000 |
| Деталь: | *Metal F10X15/14X6 18X2 |
| Парткод: | 607-16001-000 |
| Деталь: | *Bracket Gear A |
| Парткод: | 024-24138-005 |
| Деталь: | *GEAR M1X71X14 |
| Парткод: | 612-10040-004 |
| Деталь: | *Bracket Gear B |
| Парткод: | 024-24139-001 |
| Деталь: | *Cover Compress Gear 2 |
| Парткод: | 024-25044-004 |
| Деталь: | *Gear M1X17+M0.8X61 |
| Парткод: | 612-81602-003 |
| Деталь: | *Gear M0.8X17+M0.8X49 |
| Парткод: | 612-81401-008 |
| Деталь: | *Gear M0.8X15X7 |
| Парткод: | 612-11103-000 |
| Деталь: | *Bracket FG Sensor Compression Plate |
| Парткод: | 023-24074-000 |
| Деталь: | *Wire Harness M-Removal 2 |
| Парткод: | 024-25101-008 |
| Деталь: | *Bracket Compress Motor |
| Парткод: | 024-24091-009 |
| Деталь: | *Gear M0.8X35+M0.8X15 |
| Парткод: | 612-81303-006 |
| Деталь: | *Motor Assy (CWRS-445PA) |
| Парткод: | 023-75906-077 |
| Деталь: | *Support Clamp Worm |
| Парткод: | 030-19205-001 |
| Деталь: | *Motor CCWRS-555PH-24100 |
| Парткод: | 023-75907-073 |
| Деталь: | **Metal Slit Motor |
| Парткод: | 023-21342-003 |
| Деталь: | *Pulley Gear 0.8X31+53S2M |
| Парткод: | 613-11300-007 |
| Деталь: | *Belt 40-S2M-172 |
| Парткод: | 621-00005-005 |
| Деталь: | *Gear m0.8X61+m1.25X12 |
| Парткод: | 612-80024-006 |
| Деталь: | *Bracket MR Feed Gear |
| Парткод: | 024-25001-003 |
| Деталь: | *Wire Harness MM Safety Lead SW |
| Парткод: | 024-53040-006 |
| Деталь: | *Stepped Screw F5X1.5 M3X3 |
| Парткод: | 635-18513-003 |
| Деталь: | *Set Plate Safety SW M.-Rmv. |
| Парткод: | 023-24135-009 |
| Деталь: | *Spring Safety SW M-Rmv Unit |
| Парткод: | 023-24134-000 |
| Деталь: | *Wire Harness 2nd Clamp MR |
| Парткод: | 024-25100-001 |
| Деталь: | *Plate Clamp Drive 2 |
| Парткод: | 024-26513-008 |
| Деталь: | *Clamp Cam 2 |
| Парткод: | 024-26508-004 |
| Деталь: | *Clamp Sliding Cam 2 |
| Парткод: | 024-26507-008 |
| Деталь: | *Plate Clamp Sensor |
| Парткод: | 024-26511-005 |
| Деталь: | *Wire Saddle LWS-0711 |
| Парткод: | 665-02044-002 |
| Деталь: | Wire Harness MRV2 Joint |
| Парткод: | 024-53037-005 |
| Деталь: | Wire Harness Rear Upper |
| Парткод: | 024-53010-107 |
| Деталь: | Master Disposal Box Assy (1-6) |
| Парткод: | 024-75099-055 |
| Деталь: | *Cover M-Removal Box |
| Парткод: | 024-24036-008 |
| Деталь: | *M-Removal Box |
| Парткод: | 024-24035-109 |
| Деталь: | *Box Lever Disposal box |
| Парткод: | 023-24140-207 |
| Деталь: | *Handle Spring Disposal Box |
| Парткод: | 023-24148-003 |
| Деталь: | *Spring Box Cover |
| Парткод: | 024-24141-006 |
| Деталь: | *Seal Disposal Instruction Pic |
| Парткод: | 023-24143-109 |
| Деталь: | Master Disposal Box Assy (1-6) |
| Парткод: | 024-75099-055 |
| Деталь: | *Cover M-Removal Box |
| Парткод: | 024-24036-008 |
| Деталь: | *M-Removal Box |
| Парткод: | 024-24035-109 |
| Деталь: | *Box Lever Disposal box |
| Парткод: | 023-24140-207 |
| Деталь: | *Handle Spring Disposal Box |
| Парткод: | 023-24148-003 |
| Деталь: | *Spring Box Cover |
| Парткод: | 024-24141-006 |
| Деталь: | *Seal Disposal Instruction Pic |
| Парткод: | 023-24143-109 |
| Деталь: | Bracket M-Removal R |
| Парткод: | 024-24132-007 |
| Деталь: | Bracket M-Removal F |
| Парткод: | 024-24133-003 |
| Деталь: | Clamp Plate Base Assy (20-29) |
| Парткод: | 024-75100-053 |
| Деталь: | Drum Body A3 |
| Парткод: | 024-75061-058 |
| Деталь: | Drum Body LD |
| Парткод: | 024-75063-050 |
| Деталь: | Screen Assy (S) |
| Парткод: | 024-17115-008 |
| Деталь: | Light Absorber Strip (328X18) |
| Парткод: | 023-17004-306 |
| Деталь: | Hanger Plate Screen |
| Парткод: | 024-17003-005 |
| Деталь: | Block Sheet Assy A3W |
| Парткод: | 024-17011-008 |
| Деталь: | Seal Tape A3W |
| Парткод: | 024-17256-000 |
| Деталь: | DRUM SEAL |
| Парткод: | 023-17007-003 |
| Деталь: | Flange Front |
| Парткод: | 023-17012-007 |
| Деталь: | Weight Balance F A |
| Парткод: | 023-17014-000 |
| Деталь: | Weight Balance F B |
| Парткод: | 023-17262-003 |
| Деталь: | Flange Handle |
| Парткод: | 024-17149-000 |
| Деталь: | B Position Marking Sticker |
| Парткод: | 023-17307-007 |
| Деталь: | Flange Gear |
| Парткод: | 024-17009-003 |
| Деталь: | Drum Flange Rear |
| Парткод: | 023-17006-104 |
| Деталь: | Weight Balance R A |
| Парткод: | 023-17011-000 |
| Деталь: | Weight Balance R B |
| Парткод: | 023-17261-007 |
| Деталь: | Metal Stopper Drum |
| Парткод: | 023-17263-000 |
| Деталь: | Drum Joint |
| Парткод: | 024-17008-007 |
| Деталь: | Boss A-Positioning ADJ |
| Парткод: | 024-17010-109 |
| Деталь: | *Clamp Plate Base |
| Парткод: | 024-17067-100 |
| Деталь: | *Clamp Magnet |
| Парткод: | 024-17181-000 |
| Деталь: | *Friction Sheet |
| Парткод: | 024-17180-004 |
| Деталь: | *Spring Clamp Plate Base |
| Парткод: | 023-17251-001 |
| Деталь: | *Clamp Plate |
| Парткод: | 024-17068-107 |
| Деталь: | *Clamp Lever |
| Парткод: | 023-17191-106 |
| Деталь: | *Collar D12 Clamp |
| Парткод: | 023-17069-009 |
| Деталь: | *Spring Clamp Plate Close |
| Парткод: | 023-17275-008 |
| Деталь: | *Projection Plate |
| Парткод: | 024-17071-108 |
| Деталь: | *Shaft Projection Support |
| Парткод: | 024-17248-006 |
| Деталь: | Light Absorber Strip (65X18) |
| Парткод: | 023-17344-204 |
| Деталь: | Squeegee Unit Assy A3 (17-32) |
| Парткод: | 024-75073-056 |
| Деталь: | Flange Support Roller Drum |
| Парткод: | 023-17116-007 |
| Деталь: | LOCK RING 4 |
| Парткод: | 023-17197-007 |
| Деталь: | S-GAP CAM |
| Парткод: | 024-17027-001 |
| Деталь: | Spring Doctor Roller |
| Парткод: | 023-17333-008 |
| Деталь: | Stepped Screw F6X3 M4X4 |
| Парткод: | 635-17634-001 |
| Деталь: | Center Shaft |
| Парткод: | 024-17111-002 |
| Деталь: | Gear M1X45X6 |
| Парткод: | 612-10026-001 |
| Деталь: | Plate Center Shaft |
| Парткод: | 024-17511-000 |
| Деталь: | Ink Blocking Plate (Front) |
| Парткод: | 023-17229-006 |
| Деталь: | Ink Blocking Plate Front |
| Парткод: | 023-17227-003 |
| Деталь: | Shaft Screw Ink Blocking Plate |
| Парткод: | 015-36317-100 |
| Деталь: | Stepped Screw F4X3 M3X6 |
| Парткод: | 635-17433-006 |
| Деталь: | Spring Ink Blocking Plate |
| Парткод: | 015-36318-000 |
| Деталь: | Ink Blocking Plate (Rear) |
| Парткод: | 023-17228-000 |
| Деталь: | Ink Blocking Plate Rear |
| Парткод: | 023-17226-007 |
| Деталь: | *Squeegee Roller A3 |
| Парткод: | 024-17030-002 |
| Деталь: | *Doctor Roller A3 |
| Парткод: | 024-17329-008 |
| Деталь: | *Ink Drive Shaft A3 |
| Парткод: | 024-17035-004 |
| Деталь: | *Block F Squeegee |
| Парткод: | 023-17041-007 |
| Деталь: | *Metal S4X7X2 |
| Парткод: | 607-03001-001 |
| Деталь: | *O Ring P4-1.9 |
| Парткод: | 640-60040-000 |
| Деталь: | *Side Frame Squeegee F Assy |
| Парткод: | 024-17126-000 |
| Деталь: | *Adj. Plate L Squeegee Gap |
| Парткод: | 023-17336-007 |
| Деталь: | *Gear M0.8X19X4 |
| Парткод: | 612-10027-008 |
| Деталь: | *Sheet Squeegee Roller |
| Парткод: | 639-00002-000 |
| Деталь: | *Gear M0.8X43X3 |
| Парткод: | 612-10028-004 |
| Деталь: | *Side Frame Squeegee R Assy |
| Парткод: | 024-17125-003 |
| Деталь: | *Block R Squeegee |
| Парткод: | 023-17040-000 |
| Деталь: | *Adj. Plate R Squeegee Gap |
| Парткод: | 023-17334-004 |
| Деталь: | *Gear M1X25X8.5 OWC |
| Парткод: | 612-10024-009 |
| Деталь: | Fixing Plate Drive Shaft A3 |
| Парткод: | 023-17294-002 |
| Деталь: | Wire Saddle LWS-0711 |
| Парткод: | 665-02044-002 |
| Деталь: | Elevator Motor Assy (22-32) |
| Парткод: | 023-75078-050 |
| Деталь: | Plate Elevator R |
| Парткод: | 024-12207-001 |
| Деталь: | Plate Elevator F |
| Парткод: | 024-12201-003 |
| Деталь: | Absorber Gear |
| Парткод: | 024-12206-005 |
| Деталь: | Elevator Shaft Assy |
| Парткод: | 023-75159-050 |
| Деталь: | Reinforce Elevator |
| Парткод: | 024-12210-002 |
| Деталь: | Guide Shaft |
| Парткод: | 024-12211-009 |
| Деталь: | Lower Limit Frame P.-F. |
| Парткод: | 023-12205-001 |
| Деталь: | Support Lower limit Frame P.-F. |
| Парткод: | 023-12206-008 |
| Деталь: | Elevator Guide |
| Парткод: | 024-12213-001 |
| Деталь: | ELEVATOR RACK P.-F. |
| Парткод: | 023-12201-006 |
| Деталь: | Bracket F Spring Lower Safety SW |
| Парткод: | 023-12251-003 |
| Деталь: | Bracket R Spring Lower Safety SW |
| Парткод: | 023-12252-000 |
| Деталь: | Spring Elevator Safety SW Lower |
| Парткод: | 023-12237-000 |
| Деталь: | V-5F930DN |
| Парткод: | 444-05001-001 |
| Деталь: | BRACKET LOWER LIMIT SENSOR |
| Парткод: | 023-12233-102 |
| Деталь: | LG-248NL1 |
| Парткод: | 444-30008-002 |
| Деталь: | Spring Elevator |
| Парткод: | 023-12202-002 |
| Деталь: | E Spring Hook R |
| Парткод: | 024-12215-101 |
| Деталь: | FFC GUIDE |
| Парткод: | 024-12214-008 |
| Деталь: | Bearing Flaw678 ZZA |
| Парткод: | 600-50057-006 |
| Деталь: | Metal F8X13/12X5 16X2 |
| Парткод: | 607-15000-000 |
| Деталь: | *Cover Elevator Motor |
| Парткод: | 023-12247-006 |
| Деталь: | *Motor Chassis Elevator Motor |
| Парткод: | 023-12234-001 |
| Деталь: | *Gear Cover Elevator Motor |
| Парткод: | 023-12223-000 |
| Деталь: | *Gear M1x24 |
| Парткод: | 612-10009-107 |
| Деталь: | *Gear M0.8X23+M0.8X14 |
| Парткод: | 612-80011-001 |
| Деталь: | *Gear M0.8X30+M0.8X14 |
| Парткод: | 612-80012-008 |
| Деталь: | *Gear M0.8X29+M1X14 |
| Парткод: | 612-80013-004 |
| Деталь: | *Elevator Motor Collar |
| Парткод: | 023-12244-107 |
| Деталь: | *Support Clamp Worm |
| Парткод: | 030-19205-001 |
| Деталь: | Wire Harness Elevator Motor |
| Парткод: | 023-12602-108 |
| Деталь: | Bracket PFR-PCB |
| Парткод: | 024-12209-101 |
| Деталь: | PFR-PCB |
| Парткод: | 024-12601-001 |
| Деталь: | Wire Harness PFL Sensor |
| Парткод: | 024-12605-007 |
| Деталь: | Wire Harness Rear Upper |
| Парткод: | 024-53010-107 |
| Деталь: | WIRE HARNESS PF TRAY |
| Парткод: | 024-12607-107 |
| Деталь: | Wire Harness PF Motor |
| Парткод: | 024-12609-002 |
| Деталь: | Wire Harness PF Safety SW |
| Парткод: | 024-53028-006 |
| Деталь: | Wire Harness Rear Lower A |
| Парткод: | 024-53011-103 |
| Деталь: | Wire Harness Front Upper |
| Парткод: | 024-53035-100 |
| Деталь: | Wire Saddle LWS-0711 |
| Парткод: | 665-02044-002 |
| Деталь: | Detection Plate Paper Volume |
| Парткод: | 024-12216-000 |
| Деталь: | *Motor Assy (CWRS-445PA) |
| Парткод: | 023-75906-077 |
| Деталь: | Pick-Up Roller 15-16) |
| Парткод: | 021-14301-046 |
| Деталь: | Cover P-Feed |
| Парткод: | 023-12316-105 |
| Деталь: | Seal P.-Feed Pressure Pic |
| Парткод: | 550-21173-001 |
| Деталь: | Seal P.-F.-T.Down |
| Парткод: | 550-20059-108 |
| Деталь: | Upper Guard |
| Парткод: | 023-12319-007 |
| Деталь: | STEPPED SCREW F8X2.3 M4X4.4 |
| Парткод: | 635-17824-005 |
| Деталь: | E SWITCH PLATE |
| Парткод: | 023-12315-001 |
| Деталь: | SPRING ELEVATOR SAFETY SW UPPER |
| Парткод: | 023-12344-001 |
| Деталь: | Push Button SW Assy |
| Парткод: | 021-51029-003 |
| Деталь: | V-5F930DN |
| Парткод: | 023-53023-007 |
| Деталь: | FRAME BRACKET PICK-UP |
| Парткод: | 023-12333-204 |
| Деталь: | SHAFT PICK-UP ROLLER |
| Парткод: | 023-12329-002 |
| Деталь: | GEAR M0.8X33X7.4 |
| Парткод: | 612-10021-107 |
| Деталь: | METAL F10X15/14X6 18X2 |
| Парткод: | 607-16001-000 |
| Деталь: | SUPPORT PICK-UP ROLLER SHAFT |
| Парткод: | 023-12328-103 |
| Деталь: | *Rubber Roller Pick UP |
| Парткод: | 035-14303-001 |
| Деталь: | *Core:Pick-up Roller |
| Парткод: | 021-14302-000 |
| Деталь: | Lock Ring |
| Парткод: | 019-11812-106 |
| Деталь: | SCRAPER SHAFT PICKUP |
| Парткод: | 023-12330-000 |
| Деталь: | GEAR M0.8X34X8.5 |
| Парткод: | 612-11300-000 |
| Деталь: | JOINT SHAFT ASSY |
| Парткод: | 023-12338-001 |
| Деталь: | Shaft PU Extension |
| Парткод: | 023-12337-005 |
| Деталь: | Paper Guide Roller |
| Парткод: | 011-11522-002 |
| Деталь: | STOPPER PAPER GUIDE ROLLER |
| Парткод: | 000-06123-007 |
| Деталь: | ACTUATOR UPPER LIMIT STD P.-F.-T |
| Парткод: | 023-12334-006 |
| Деталь: | ACTUATOR UPPER LIMIT CARD P.-F.-T |
| Парткод: | 023-12308-005 |
| Деталь: | Stay Paper Feed |
| Парткод: | 023-12310-000 |
| Деталь: | ARM P.-F.PRESSURE ADJ. |
| Парткод: | 020-11813-006 |
| Деталь: | Spring B P.-F.Pressure Adj |
| Парткод: | 020-11811-100 |
| Деталь: | P.-F.Pressure Adj.Lever |
| Парткод: | 023-12312-100 |
| Деталь: | SPRING PF PRESSURE ADJ. LEVER |
| Парткод: | 023-12313-009 |
| Деталь: | BRACKET A UPPER LIMIT SENSOR |
| Парткод: | 023-12314-005 |
| Деталь: | Support Plate B Upper Limit |
| Парткод: | 030-14342-108 |
| Деталь: | Upper Limit Adj. Screw |
| Парткод: | 030-14346-006 |
| Деталь: | BASE UPPER LIMIT ADJ. SCREW |
| Парткод: | 030-14347-002 |
| Деталь: | BRACKET UPPER LIMIT SENSOR |
| Парткод: | 023-12325-007 |
| Деталь: | Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | Wire Harness PFU Sensor |
| Парткод: | 024-12604-000 |
| Деталь: | PF ONE-WAY Core Base Assy |
| Парткод: | 024-15168-007 |
| Деталь: | Base ONE-WAY Hook |
| Парткод: | 024-15171-008 |
| Деталь: | ONE-WAY Hook |
| Парткод: | 024-15187-001 |
| Деталь: | Stepped Screw 8X1.7 M4X4.3 |
| Парткод: | 635-17814-000 |
| Деталь: | Spring ONE-WAY Hook |
| Парткод: | 024-15172-004 |
| Деталь: | PF ONE-WAY Core Assy |
| Парткод: | 024-15173-000 |
| Деталь: | Catch PU Clutch |
| Парткод: | 024-15083-109 |
| Деталь: | MC-10-25 |
| Парткод: | 490-51018-000 |
| Деталь: | Metal F8X13/12X5 16X2 |
| Парткод: | 607-15000-000 |
| Деталь: | Metal F8X12/10.8X14 16X2 |
| Парткод: | 607-15001-503 |
| Деталь: | Solenoid TDS-10A-1056 |
| Парткод: | 490-50006-009 |
| Деталь: | Wire Harness PF Motor |
| Парткод: | 024-12609-002 |
| Деталь: | 1st Master Removal Unit (Fig26-Fig27 1-49) |
| Парткод: | 024-75065-053 |
| Деталь: | *Removal Housing Base |
| Парткод: | 024-24021-108 |
| Деталь: | *Housing Fixing Plate |
| Парткод: | 024-24128-000 |
| Деталь: | *Roller Hook |
| Парткод: | 024-25062-100 |
| Деталь: | *Spring Roller Hook |
| Парткод: | 024-25058-005 |
| Деталь: | *Gear M1.25X12X7 |
| Парткод: | 612-10004-008 |
| Деталь: | *Gear M1.25X13X6 |
| Парткод: | 612-10042-007 |
| Деталь: | *Gear M1.25X12 |
| Парткод: | 612-10002-005 |
| Деталь: | *Spring MR Roller AR |
| Парткод: | 024-24059-008 |
| Деталь: | *Spring MR Roller AF |
| Парткод: | 024-24058-001 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | *M-Rmv Guide |
| Парткод: | 024-24145-001 |
| Деталь: | *Spring M-Rmv Guide B |
| Парткод: | 024-24147-004 |
| Деталь: | *Spring M-Rmv Guide A |
| Парткод: | 024-24146-008 |
| Деталь: | *Shaft M-Rmv Guide |
| Парткод: | 024-24144-102 |
| Деталь: | *Bracket M-Jam Sensor 1 |
| Парткод: | 024-24056-009 |
| Деталь: | *Sensor OS-RS04Y01 |
| Парткод: | 444-41003-002 |
| Деталь: | *Shaft MR Pulley Plate |
| Парткод: | 024-25007-001 |
| Деталь: | *Plate M.-Rmv. Pulley |
| Парткод: | 023-24062-109 |
| Деталь: | *Spring Roller B1 |
| Парткод: | 024-24067-000 |
| Деталь: | *Holding Plate Pulley M.-Rmv. |
| Парткод: | 023-24129-009 |
| Деталь: | *Pulley Shaft M.-Rmv |
| Парткод: | 023-24025-203 |
| Деталь: | *Lock Ring 4 |
| Парткод: | 023-17197-007 |
| Деталь: | *Metal F6X10/9X6:12 X 1.5 |
| Парткод: | 607-13000-402 |
| Деталь: | *Shaft Pulley M-Rmv |
| Парткод: | 023-24063-202 |
| Деталь: | *Pulley M-Rmv |
| Парткод: | 023-24061-102 |
| Деталь: | *Master Removal Roller (UP) |
| Парткод: | 023-24057-008 |
| Деталь: | *Transfer Belt 2 2X130 |
| Парткод: | 628-00002-007 |
| Деталь: | *Wire Removal Sensor 1 |
| Парткод: | 024-24140-000 |
| Деталь: | PF Tray Assy (1-30) |
| Парткод: | 024-75089-050 |
| Деталь: | *PFT Table L |
| Парткод: | 024-12102-102 |
| Деталь: | *Seal PFT Close |
| Парткод: | 024-12122-006 |
| Деталь: | *Feed Tray Cover |
| Парткод: | 024-12101-009 |
| Деталь: | *L.O. Sheet |
| Парткод: | 020-11520-009 |
| Деталь: | *Slider F Paper Guide |
| Парткод: | 030-14126-006 |
| Деталь: | *Lock B Paper Guide |
| Парткод: | 030-14130-003 |
| Деталь: | *Lock A Paper Guide |
| Парткод: | 030-14129-005 |
| Деталь: | *Shaft PF Tray |
| Парткод: | 024-12105-004 |
| Деталь: | *Slider R Paper Guide |
| Парткод: | 030-14124-003 |
| Деталь: | *GEAR M1X16X3.2 |
| Парткод: | 612-12103-003 |
| Деталь: | *Slide Rack P-F-T |
| Парткод: | 024-12110-008 |
| Деталь: | *Collar Slide Rack P-F-T |
| Парткод: | 030-14133-002 |
| Деталь: | *Frame PF Tray F |
| Парткод: | 024-12112-000 |
| Деталь: | *Cover Hinge |
| Парткод: | 024-12111-004 |
| Деталь: | *Shaft Hinge |
| Парткод: | 024-12109-000 |
| Деталь: | *Gear M1x20x7 |
| Парткод: | 612-10036-007 |
| Деталь: | *One-Way Hinge OWHF6-1NRS |
| Парткод: | 610-10009-005 |
| Деталь: | *Frame PF Tray R |
| Парткод: | 024-12113-007 |
| Деталь: | *PF-Tray-PCB |
| Парткод: | 024-12602-008 |
| Деталь: | *Bracket Potentiometer |
| Парткод: | 024-12127-008 |
| Деталь: | *Gear M1X72X6 |
| Парткод: | 612-10039-006 |
| Деталь: | *Potentiometer Assy |
| Парткод: | 021-51032-209 |
| Деталь: | *Sensor PS-117ND1 |
| Парткод: | 444-33005-004 |
| Деталь: | *Wire Harness PF Tray Inner |
| Парткод: | 024-12608-103 |
| Деталь: | *Lever Fence Lock |
| Парткод: | 024-12120-003 |
| Деталь: | *Fence Tray F |
| Парткод: | 024-12106-000 |
| Деталь: | *Fence Tray R |
| Парткод: | 024-12107-007 |
| Деталь: | *Fence Sheet |
| Парткод: | 024-12123-002 |
| Деталь: | *Seal Fence Set |
| Парткод: | 024-12121-000 |
| Деталь: | *PFT Table S |
| Парткод: | 024-12108-100 |
| Деталь: | FIXED PLATE PFT |
| Парткод: | 024-12119-005 |
| Деталь: | FFC COVER |
| Парткод: | 024-12116-006 |
| Деталь: | FFC holder |
| Парткод: | 024-12125-005 |
| Деталь: | WIRE HARNESS PF TRAY |
| Парткод: | 024-12607-107 |
| Деталь: | Magnet Catch SM-50P |
| Парткод: | 660-05000-018 |
| Деталь: | Horizontal Motor Unit Assy (17-48) |
| Парткод: | 024-75091-054 |
| Деталь: | Slide Rail |
| Парткод: | 024-17063-008 |
| Деталь: | Drum Support Left Rail |
| Парткод: | 023-17062-101 |
| Деталь: | Drum Support Right Rail |
| Парткод: | 023-17061-105 |
| Деталь: | Pre-Pressure Spring Left |
| Парткод: | 023-17140-102 |
| Деталь: | Pre-Pressure Spring Rig |
| Парткод: | 023-17139-104 |
| Деталь: | STAY RAIL |
| Парткод: | 024-17060-009 |
| Деталь: | Guide Front Frame R |
| Парткод: | 024-17203-004 |
| Деталь: | Guide Front Frame L |
| Парткод: | 024-17204-000 |
| Деталь: | Seal Drum Set Position |
| Парткод: | 023-17302-005 |
| Деталь: | Guide Front Frame Cover |
| Парткод: | 024-17400-004 |
| Деталь: | Bracket B-Release Base |
| Парткод: | 024-17278-101 |
| Деталь: | Base B Position Release |
| Парткод: | 024-17166-109 |
| Деталь: | Slide Shaft R Assy |
| Парткод: | 024-17500-106 |
| Деталь: | Slide Shaft L Assy |
| Парткод: | 024-17518-005 |
| Деталь: | Plate Slide Shaft ADJ |
| Парткод: | 024-17520-107 |
| Деталь: | Blind Plate |
| Парткод: | 024-17523-009 |
| Деталь: | *Base Horizontal Motor |
| Парткод: | 024-18002-002 |
| Деталь: | *Gear M0.8X65X6 |
| Парткод: | 612-10037-003 |
| Деталь: | *Gear M0.8X41X6 |
| Парткод: | 612-10038-000 |
| Деталь: | *Washer |
| Парткод: | 024-18011-001 |
| Деталь: | *Gear M0.8X16+M0.8X36 |
| Парткод: | 612-81304-002 |
| Деталь: | *Motor X03-42D4-050 |
| Парткод: | 490-31011-000 |
| Деталь: | *Base Horizontal Movement |
| Парткод: | 024-18001-006 |
| Деталь: | *Catch Horizontal Guide Shaft |
| Парткод: | 024-18030-006 |
| Деталь: | *Guide H-Pressure Spring |
| Парткод: | 024-18010-005 |
| Деталь: | *Sub Movable Plate |
| Парткод: | 024-17524-005 |
| Деталь: | *Edging Saddle TSB-1909L |
| Парткод: | 665-04068-006 |
| Деталь: | *Bracket Horizontal Sensor |
| Парткод: | 024-18013-101 |
| Деталь: | *Plate Horizontal Sensor Cover |
| Парткод: | 024-18031-002 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | *Wire Harness D-Drawer H |
| Парткод: | 024-53030-108 |
| Деталь: | *Wire Harness D-Drawer H U |
| Парткод: | 024-53031-007 |
| Деталь: | *Slide Guide Horizontal |
| Парткод: | 024-18017-000 |
| Деталь: | *Spring Horizontal |
| Парткод: | 024-18009-007 |
| Деталь: | *Horizontal Screw |
| Парткод: | 024-18008-000 |
| Деталь: | *Catch Horizontal Screw |
| Парткод: | 024-18029-008 |
| Деталь: | *Movable Plate |
| Парткод: | 024-18014-000 |
| Деталь: | *SW Base Plate |
| Парткод: | 024-18022-003 |
| Деталь: | *Spring Safety SW |
| Парткод: | 024-18028-001 |
| Деталь: | *SW Plate |
| Парткод: | 024-18027-005 |
| Деталь: | *D-Lock Lever |
| Парткод: | 024-18020-000 |
| Деталь: | *Spring D-Lock |
| Парткод: | 024-18021-007 |
| Деталь: | *Shaft D-Lock |
| Парткод: | 024-18019-002 |
| Деталь: | *Shaft Horizontal Guide |
| Парткод: | 024-18012-008 |
| Деталь: | *Link Plate Horizontal |
| Парткод: | 024-18015-007 |
| Деталь: | *Bracket D-Lock Sensor |
| Парткод: | 024-17164-106 |
| Деталь: | *Solenoid TDS-08A-4104 |
| Парткод: | 490-50010-006 |
| Деталь: | *Detection Plate |
| Парткод: | 024-17525-001 |
| Деталь: | Solenoid cover |
| Парткод: | 024-17527-101 |
| Деталь: | Wire Harness FL Motor |
| Парткод: | 024-53036-009 |
| Деталь: | Wire Harness Drum Drawer Junction |
| Парткод: | 024-53026-003 |
| Деталь: | Wire Harness F-Safety SW |
| Парткод: | 024-53034-006 |
| Деталь: | Bracket D-Release Button |
| Парткод: | 024-50021-000 |
| Деталь: | Push Button SW Assy |
| Парткод: | 021-51029-003 |
| Деталь: | Wire Harness Front Upper |
| Парткод: | 024-53035-100 |
| Деталь: | SH4F-PCB |
| Парткод: | 024-50502-009 |
| Деталь: | SH4F-PCB(C) |
| Парткод: | 024-50504-702 |
| Деталь: | Wire Harness TPH CTL Joint |
| Парткод: | 024-53051-008 |
| Деталь: | Wire Harness Rear PS Upper |
| Парткод: | 024-53002-007 |
| Деталь: | Wire Harness Panel |
| Парткод: | 024-53050-001 |
| Деталь: | Wire Harness Rear Upper |
| Парткод: | 024-53010-107 |
| Деталь: | Printer-PCB |
| Парткод: | 024-50506-004 |
| Деталь: | Wire Harness Printer |
| Парткод: | 024-53054-007 |
| Деталь: | Noise Reduction Plate |
| Парткод: | 024-50024-000 |
| Деталь: | Bracket SH PCB |
| Парткод: | 024-50006-001 |
| Деталь: | Plate OP-IF |
| Парткод: | 024-50007-008 |
| Деталь: | USB Cover |
| Парткод: | 024-50009-000 |
| Деталь: | Cover NET-D |
| Парткод: | 024-50025-006 |
| Деталь: | Card cover |
| Парткод: | 024-50008-004 |
| Деталь: | Hinge P-Feed U |
| Парткод: | 024-50011-005 |
| Деталь: | Plate PS PCB Support |
| Парткод: | 024-50023-003 |
| Деталь: | Hinge P-Feed L |
| Парткод: | 024-50012-001 |
| Деталь: | Bracket Rear Cover SW Assy |
| Парткод: | 024-34035-000 |
| Деталь: | Shaft Bracket Drive Interlock SW |
| Парткод: | 023-50042-000 |
| Деталь: | Spring Drive Interlock SW |
| Парткод: | 023-50041-004 |
| Деталь: | Button Drive Interlock SW |
| Парткод: | 023-50055-005 |
| Деталь: | DRIVE INTERLOCK SAFETY SW |
| Парткод: | 023-53026-006 |
| Деталь: | Bracket P-Rcv Side Drive Interl SW |
| Парткод: | 023-50051-107 |
| Деталь: | Spring Rear Cover SW Assy |
| Парткод: | 024-34043-002 |
| Деталь: | Edging Saddle TSB-3027L |
| Парткод: | 665-04069-002 |
| Деталь: | Wire Saddle LWS-0711 |
| Парткод: | 665-02044-002 |
| Деталь: | Square Bushing SB-2718 |
| Парткод: | 665-04054-005 |
| Деталь: | Square Bushing SB-6025 |
| Парткод: | 665-04055-001 |
| Деталь: | Wire Saddle LWS-2218 |
| Парткод: | 665-02055-004 |
| Деталь: | Square Bushing SB-4025 |
| Парткод: | 665-04002-005 |
| Деталь: | Wire Saddle LWS-1316 |
| Парткод: | 665-02043-006 |
| Деталь: | Pressure CTL Unit (1-11) |
| Парткод: | 024-75088-053 |
| Деталь: | Second PF Motor Unit (26-30) |
| Парткод: | 024-75097-052 |
| Деталь: | *Cover Plate Pressure CTL |
| Парткод: | 024-15027-004 |
| Деталь: | *Bracket Pressure HP Sensor |
| Парткод: | 024-15032-008 |
| Деталь: | *Sensor LG-248Nl1 |
| Парткод: | 444-30008-002 |
| Деталь: | *Pressure Detection Plate |
| Парткод: | 024-15033-004 |
| Деталь: | *Pressure CTL Wheel |
| Парткод: | 023-15031-004 |
| Деталь: | *Pressure ADJ Base Plate Assy |
| Парткод: | 024-15023-009 |
| Деталь: | *Pressure CTL Worm |
| Парткод: | 023-15030-008 |
| Деталь: | *Shaft Pressure CTL Worm |
| Парткод: | 023-15029-000 |
| Деталь: | *Shaft Pressure CTL Gear |
| Парткод: | 023-15025-004 |
| Деталь: | *Pressure CTL Gear |
| Парткод: | 023-15028-003 |
| Деталь: | *Motor KH42JM2B173 |
| Парткод: | 490-31010-003 |
| Деталь: | Noise Reduction Pressure Spring |
| Парткод: | 023-15019-004 |
| Деталь: | Pressure Spring S25 |
| Парткод: | 024-15018-005 |
| Деталь: | Pressure Lever Assy |
| Парткод: | 024-15130-000 |
| Деталь: | Spring Pressure Lever |
| Парткод: | 024-15160-006 |
| Деталь: | Pressure Cam Follower Assy |
| Парткод: | 024-15014-107 |
| Деталь: | Frame Pressure CTL |
| Парткод: | 024-15157-005 |
| Деталь: | Solenoid TDS-10AL-38 |
| Парткод: | 490-50009-008 |
| Деталь: | Pressure Solenoid Base Assy |
| Парткод: | 024-15020-000 |
| Деталь: | Spring Pressure Solenoid |
| Парткод: | 030-12112-008 |
| Деталь: | Lever Pressure Solenoid |
| Парткод: | 030-12114-000 |
| Деталь: | SPRING SEPARATOR |
| Парткод: | 024-15038-006 |
| Деталь: | Plate Separator Lever |
| Парткод: | 024-15090-008 |
| Деталь: | Belt 338-2GT-6 |
| Парткод: | 620-83001-009 |
| Деталь: | Pulley P60-2GT-9 |
| Парткод: | 611-90017-000 |
| Деталь: | *Second Idler Plate Assy |
| Парткод: | 024-15143-004 |
| Деталь: | *Idler A |
| Парткод: | 021-12031-009 |
| Деталь: | *Spring Second Idler |
| Парткод: | 024-15162-009 |
| Деталь: | *Bracket Second PF Motor |
| Парткод: | 024-15140-005 |
| Деталь: | *UGFMED-C9MRS |
| Парткод: | 490-21023-000 |
| Деталь: | Gear M1X48+M1X37 |
| Парткод: | 612-80022-003 |
| Деталь: | G Roller Release Plate B |
| Парткод: | 024-15195-004 |
| Деталь: | G Roll Release Plate |
| Парткод: | 024-15183-006 |
| Деталь: | Plate G Spring Hook |
| Парткод: | 024-15148-006 |
| Деталь: | Spring Guide Roller Release |
| Парткод: | 023-15063-100 |
| Деталь: | GEAR M1X28X8 |
| Парткод: | 612-12208-107 |
| Деталь: | Bracket PU Clutch |
| Парткод: | 024-15041-104 |
| Деталь: | Wire Harness Rear Lower B |
| Парткод: | 024-53012-100 |
Коды ошибок
A01
A02
A04
A05
A06
A07
A08
A09
A10
A16
A17
A25
A34
A42
A44
A45
A48
A56
B01
B21
B22
B23
B24
B31
B32
B33
B34
B35
C01
C02
C03
C04
C05
C41
C43
D01
D02
D03
D04
D05
D07
D08
D09
D11
D13
D17
D18
D19
D20
D21
D22
D28
D30
D41
D42
D43
D44
D47
D58
D62
D68
E01
E02
F01
F02
F03
F05
F10
F24
F30
F32
F37
F43
F44
F45
F46
F47
F48
F49
F52
F58
F60
F61
F62
F63
F64
F65
F66
F67
F68
F69
F70
F71
F72
F73
F74
F75
F76
F77
F78
F79
F80
F81
F82
F83
F85
F90
F91
H01
H04
H07
T01
T02
T03
T04
T05
T06
T11
T12
T13
T14
T15
T17
T19
T20
T24
T25
T27
T29
T31
T41
T43
T44
T45
T46
T51
T52
T64
T67
T91
T92
T93
T94
T95
T96
T97
T98
T99
Описание
| Error code: | A01 |
| Display: | A01-xxx Master Mis-Feed Pull Out Master Making Unit and Rewind Master Roll, then Reset Master in Place. |
| Description: | Master feed error |
| Causes: | 201 Master-positioning sensor does not go ON even after the write pulse motor is activated during the master-positioning, master-cut, or master-loading operation. 202 Master-positioning sensor does not go OFF even when the write pulse motor is reversed during the master-positioning or at start of master-making operation. 211 Master-positioning sensor is ON during standby. 214 Master-positioning sensor is ON at the start of master making. 215 Faulty gate-array control for the write pulse motor (motor does not stop within set time). |
| Remedy: | Open the master-making unit and rewind the master material on the master roll, and then reset the master, or turn OFF the power and power back ON. |
| Error code: | A02 |
| Display: | A02-xxx Master Loading Error Pull Out Print Cylinder and Discard Master. |
| Description: | Master loading error |
| Causes: | 509 Master-loading sensor was OFF when the master was checked at a specified drum angle during the master-loading operation. |
| Remedy: | Pull out the print cylinder and set it back. |
| Error code: | A04 |
| Display: | A04-xxx Master Disposal Error Pull Out Print Cylinder and Discard Master. |
| Description: | Master disposal error |
| Causes: | 303 Check Print Drum - Master disposal error / Master disposal jam. |
| Remedy: | Pull out the print drum and push it back in. |
| Error code: | A05 |
| Display: | A05-xxx Master Jammed in Disposal Unit Pull Out Master Disposal Box and Remove Jammed Master |
| Description: | Master present in the master disposal area |
| Causes: | 304 Master disposal jam sensor was ON at the completion of the master disposal. 312 Master disposal jam sensor was ON at the start of the master making. 315 Master disposal jam sensor was ON after the completion of the recovery movement. |
| Remedy: | Pull out master disposal box and place it back after removing the jammed master in the master disposal area, or turn OFF the power and power back ON. |
| Error code: | A06 |
| Description: | Check paper feed tray |
| Causes: | 403 Either the upper or lower safety switch of the paper-feed-tray is OFF. Note: This detection is not made when the machine is in low-power-mode (24V OFF). |
| Remedy: | Change the condition of the paper-feed-tray upper/lower safety switches to ON condition, or turn OFF the power and power back ON. |
| Error code: | A07 |
| Display: | A07 [Paper feed error] |
| Description: | Paper feed error |
| Causes: | 409 Paper-ejection sensor was OFF when the paper should have arrived, and the paper sensor was ON when the machine stopped (Paper misfeed). 412 Paper sensor was OFF three times in succession when a paper misfeed was detected (paper misfeed). 413 Paper sensor was still ON (detecting paper) when the paper should have went out from the sensor. 418 The paper sensor was ON at the start of machine operation when the START button was pressed. 429 Paper feed error (recovery error). 432 Paper sensor was ON when the machine went into paper feed retry movement after a paper misfeed. |
| Error code: | A08 |
| Display: | A08 [Paper jam on print drum] |
| Description: | Paper jam on print drum |
| Causes: | 410 Paper-ejection sensor was OFF when paper should have arrived, and the paper sensor was OFF when the machine stopped (paper jam on the print drum). 430 Paper jam on print drum (recovery error). |
| Error code: | A09 |
| Display: | A09 [Paper ejection error] |
| Description: | Paper ejection error |
| Causes: | 411 Paper-ejection sensor was ON when the paper should have left the paper-ejection sensor. 417 Paper-ejection sensor was ON at the start of machine operation when the START button was pressed. 431 Paper-ejection error (recovery error). |
| Error code: | A10 |
| Display: | A10-Paper Output Jam |
| Description: | Paper did not exit the printer or fuser properly, causing a paper jam. Open Cover A and refer to the labels on the printer to clear the jam. |
| Causes: | 102 The original is pulled out from the AF unit before the scanning is completed. 103 Original jammed under AF registration sensor. 103 Original jam at AF registration sensor. Simplex AF: Registration-sensor does not go OFF after Original-IN-sensor goes ON. Duplex AF: Registration-sensor does not go OFF after the original feeds. 105 Original jammed at AF Read sensor. 106 Original jammed at original ejection sensor. 106 Original jam at AF original out sensor. Simplex AF: Original-OUT-sensor does not go OFF after Original-IN-sensor goes OFF. Duplex AF: Original-OUT-sensor does not go OFF after Registration-sensor goes OFF. 107 Original does not arrive to the AF Registration sensor. 108 Original does not arrive to the AF Read sensor. 109 Original does not arrive to the original ejection sensor. 109 Original Jam before AF original out sensor. Simplex AF: Original-OUT-sensor does not go ON after Original-IN-sensor goes ON. Duplex AF: Original-OUT-sensor does not go ON after the original feeds. 169 AF feed cover is opened due to original jam, while originals are present on the tray. 178 Original Jam before Original reverse sensor. Duplex AF: Original reverse sensor does not go ON after the original feeds. 179 Original Jam at Original reverse sensor. Duplex AF: Original reverse sensor does not go OFF after the original feeds. 180 Duplex AF: Original multiple feed |
| Remedy: | 1. Ensure the correct weight and type of paper is loaded in the currently used tray. Also ensure the paper is loaded correctly in the tray. 2. Clean the exit rollers. 3. Ensure the exit rolls rotate freely when the exit roller gear train is rotated. 4. At the rear of the printer, inspect the gate which directs the print to the face-up output bin or the face-down output bin. 5. Test the fuser motor (which drives the exit gear train) using the test described in “Motor and clutch tests”. Replace the engine controller board. |
| Error code: | A16 |
| Display: | A16-xxx Master Remains on Print Cylinder (Drum) Pull Out Print Cylinder and Remove Master |
| Description: | Waiting for the master to be removed from the drum |
| Causes: | 525 Waiting for the master to be removed from the print cylinder (drum). |
| Remedy: | Pull out the print cylinder (drum), remove the master around it and insert it back. |
| Error code: | A17 |
| Display: | A17-xxx System Error in Master Making Unit Take Out Master and then Close Master Making Unit Cover |
| Description: | Cutter error |
| Causes: | 209 Cutter HP switch is OFF when master-making starts, when the master material is set in the master making unit, or when the machine goes into idle condition. |
| Remedy: | Open the Master making unit, remove the master and close the master making unit. |
| Error code: | A25 |
| Description: | Central transport error |
| Causes: | 419 The central transport sensor was ON at the start of the operation. 440 The central transport sensor was OFF at the time the paper reached the central transport sensor (central transport error). 441 The central transport sensor was ON at the time the paper left the central transport sensor (central transport error). 447 The central transport sensor was ON when the paper reached the central transport sensor, and the central transport sensor was OFF when the operation stopped (central transport error). |
| Error code: | A34 |
| Display: | A34-xxx Master Not Set in Place Insert Lead Edge of Master into Master Entrance and Close Master Making Unit |
| Description: | Requesting for the master to be reset |
| Causes: | 218 Reqesting for the master material to be reset into the master making unit. |
| Remedy: | Open the Master making unit, re-insert the master material into the master making unit. |
| Error code: | A42 |
| Description: | Master loading error on second print drum side |
| Causes: | 509 The master loading sensor was OFF when the presence of master was checked at the specified angle during master-loading operation. |
| Remedy: | Second print drum connection signal: ON -> OFF and second print drum safety SW: ON -> OFF << Pull out the print drum to cancel the error. >> * If the print drum is at position B when this error occurs, the print drum lock is automatically released. |
| Error code: | A44 |
| Description: | Master removal error on second print drum side |
| Causes: | 303 Master removal error or removed master jam detected during the print drum check. |
| Remedy: | Second print drum connection signal: ON -> OFF and second print drum safety SW: ON -> OFF << Pull out the print drum to cancel the error. >> * If the print drum is at position B when this error occurs, the print drum lock is automatically released. |
| Error code: | A45 |
| Description: | Master present in master removal section on second print drum side |
| Causes: | 304 Master removal error or removed master jam detected during the master disposal box check. 312 The master disposal jam sensor was ON at the start of the master-making operation. 315 The master disposal jam sensor was ON at the completion of the recovery operation. |
| Remedy: | Second master disposal box safety SW: OFF and second master disposal jam sensor: OFF << When the master disposal box is pulled out, if the master has been removed, the error is cancelled. >> (Or switch power OFF, then ON.) |
| Error code: | A48 |
| Description: | Paper jam on second print drum |
| Causes: | 410 The central transport (paper ejection) sensor was OFF at the time the paper reached the central transport (paper ejection) sensor, and the paper feed (central transport) sensor was OFF when the operation stopped (paper jam on print drum). |
| Error code: | A56 |
| Description: | Awaiting removal of master from second print drum side |
| Causes: | 525 Wait for the master to be removed. |
| Remedy: | Second print drum connection signal: ON -> OFF and second print drum safety SW: ON -> OFF << Pull out the print drum to cancel the error. >> * If the print drum is at position B when this error occurs, the print drum lock is automatically released. |
| Error code: | B01 |
| Description: | Keycard counter: No card |
| Causes: | 730 Keycard counter: No card O O |
| Remedy: | Insert card. |
| Error code: | B21 |
| Display: | B21-Duplex Area Jam |
| Description: | Paper did not exit the transport area correctly, causing a paper jam. Open Cover B and refer to the labels on the printer to clear the jam. |
| Causes: | 714 File name error on the Hold Memory. 715 Access error on the Hold Memory. 716 Other error on the Hold Memory. |
| Remedy: | 1. Ensure the correct weight and type of paper is loaded in the currently used tray. Also ensure the paper is loaded correctly in the tray. 2. Clean the duplex unit’s rollers. 3. Test the duplex motor and clutch as described in “Motor and clutch tests”. Replace the duplex unit. 5. Replace the engine controller board. |
| Error code: | B22 |
| Display: | B22-xxx !! Job Separator is OFF !! Turn On Power Switch of it |
| Description: | Job separator: Power off |
| Causes: | 721 With the [Tape separation] function set ON, no power is supplied to the job separator when start key is pressed. 727 After cluster-A signal turned ON, BUSY-signal stayed [L] more than 7 seconds (power to job separator was turned OFF while the tape is being ejected. |
| Remedy: | Press Reset Key and check and switch ON the power of Job Separator. |
| Error code: | B23 |
| Display: | B23-xxx No Paper Tape in Job Separator Replace Tape Roll |
| Description: | Job separator: No tape |
| Causes: | 722 With the [Tape separation] function set ON, no tape detected in the job separator when the start key is pressed. 723 No tape remains in job separator upon completion of the tape-ejection operation. |
| Remedy: | Press Reset Key and set paper tape in Job Separator. |
| Error code: | B24 |
| Display: | B24-xxx Paper Tape Jam in Job Separator Remove Paper Tape |
| Description: | Job separator: Tape jam |
| Causes: | 724 Tape jam detected when the start key is pressed with the [Tape separation] function set to ON. 725 The tape-jam detection signal is [H] for more than 1.2 seconds after cluster-A signal turns ON (tape misfeed). 726 Job separator tape-jam detection signal is [L] when the BUSY signal changes from [L] to [H] (or after 7 sec. at [L]) after the cluster-A signal goes ON (tape misfeed). |
| Remedy: | Press Reset Key and remove the jammed tape. |
| Error code: | B31 |
| Display: | B31-xxx !! No Linked Printer Detected !! Check Cable Connection and Power Supply for Linked Printer |
| Description: | Network cable not connected |
| Causes: | 916 Network cable is not connected when the machine is powered ON. |
| Remedy: | Press Reset Key and connect the network cable. |
| Error code: | B32 |
| Display: | B32-xxx !! No Linked Printer Detected !! Check Cable Connection and Power Supply for Linked Printer |
| Description: | NIC - Communication error |
| Causes: | 914 MIB (Management Informtion Base) request error 915 MIB no reply 917 Communication error on the network. 920 Error detected by Network Interface Card (NIC) - NAK (negative acknowledgement was received). |
| Remedy: | Press Reset Key, and check the network cable and linked printer. |
| Error code: | B33 |
| Display: | B33-xxx No IP Address Assigned to This Printer Contact Your Network Administrator |
| Description: | IP address set up error |
| Causes: | 931 DHCP is ON, but DHCP server is not found. |
| Remedy: | Press Reset Key, and enter the IP address. |
| Error code: | B34 |
| Description: | Linked Printer Error (RZ3) [Linked Printer - No Toner Error] (RZ5 & RZ9) |
| Causes: | 919 Error on the linked printer. 919 No toner in the linked printer. |
| Remedy: | Press [Reset] Key and correct the error on the linked printer (RZ3). Press [Reset] Key and replace the toner on the linked printer (RZ5 & RZ9). |
| Error code: | B35 |
| Description: | Linked Printer: Call Service Error |
| Causes: | 970 Error in the linked printer. |
| Remedy: | Press Reset Key, and correct the error on the linked printer. |
| Error code: | C01 |
| Display: | C01-xxx No Ink Replace Ink Cartridge |
| Description: | Main motor is abnormal |
| Remedy: | Is the main motor working? NO 1. Check if the connector CN1 of the main motor is disconnected. 2. Check if the connector J313 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circutied. 4. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 5. Replace the main motor. 6. Replace the LGC board. YES Is the LED on the main motor board lit without flickering? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 3. Replace the main motor. 4. Replace the LGC board. YES 1. Check if the PLL lock signal J313-11 output from the LGC board is always level “L”? 2. Check if the voltage supplied to the microcomputer input terminal IC10-7 is always “L”? 3. Replace the LGC board. |
| Error code: | C02 |
| Display: | C02-xxx No Master Replace Master Roll |
| Description: | Replace master roll |
| Causes: | 200 The master end was detected twice in succession at 10-milliseconds intervals during master transport. 240 Master remaining amount is zero from the RF-Tag information. 253 Masterless error was detected twice consecutively on one same master-roll. |
| Remedy: | Remove the empty master roll and replace with a new one. |
| Error code: | C03 |
| Display: | C03-xxx Master Disposal Box is Full Empty Master Disposal Box |
| Description: | Master disposal box full |
| Causes: | 308 Compression detection position was reached before the master-compression-motor encoder-sensor count reached the specified level, after the master compression motor turned ON in the compressing direction. |
| Remedy: | Remove master disposal box from the machine, throw away the disposed master from the disposal box and return the disposal box in the machine after an interval of over 5 seconds. |
| Error code: | C04 |
| Display: | C04-xxx Add Paper |
| Description: | Abnormal feed motor |
| Causes: | 402 Paper detection sensor is OFF (not detecting paper). |
| Remedy: | Is the PFP motor working? (Perform the output check in the test mode: 03-125/175) NO 1. Check if the signal line connector of the feed motor is disconnected. 2. Check if the connector J327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the feed motor board and LGC board are short- or open circuited. 5. Replace the feed motor. 6. Replace the LGC board. YES Is the LED on the feed motor board lit without flashing? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the feed motor board and LGC board are short- or open-circuited. 3. Replace the feed motor. 4. Replace the LGC board. YES Replace the LGC board. |
| Error code: | C05 |
| Description: | ADU motor rotation abnormal |
| Causes: | 317 After the master compression motor on the first print drum side or second print drum side begins to apply a compression force, the compression detection activates and the other disposal box exceeds 90% capacity before the FG count exceeds the specified volume (Expected disposal box full). |
| Remedy: | Is the ADU motor rotating properly? N: 1. Check if the harness between the LGC board and the ADU drawer connector is open-circuited. 2. Check if the harness between the switching power supply and the ADU drawer connector is open-circuited. 3. Check if any of the connectors J101, J102 and J104 on the LGC board is disconnected. 4. Reduce the mechanical load on the motor by adjusting the drive system. Remove foreign matter if any. 5. Replace the LGC board. Y: Are the pins B2 and B4 of the connector J104 on the LGC board always at the level "L"? N: 1. Check if the connector J104 on the LGC board is disconnected. 2. Check if any conductor pattern on the LGC board is open- or short-circuited. 3. Check if any harness is open-circuited or any connector pin is disconnected. 4. Replace the LGC board. Y: 1. Check if any conductor pattern on the LGC board is open- or short-circuited. 2. Replace the LGC board. |
| Error code: | C41 |
| Description: | Thermistor or heater abnormal when warming-up is started |
| Causes: | MAIN board Switching regulator |
| Remedy: | 1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally. |
| Error code: | C43 |
| Description: | Thermistor abnormal during warming-up after abnormality judgment |
| Causes: | MAIN board Switching regulator |
| Remedy: | 1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally. |
| Error code: | D01 |
| Display: | D01-xxx Set Print Cylinder (Drum) in Place |
| Description: | Print drum not set |
| Causes: | 526 Print drum is not set in the machine (drum connection signal, drum safety switch, and drum-lock sensor is OFF. 527 Print drum connection signal is OFF when the print drum was inserted in the machine. 528 Print drum safety switch is OFF when the print drum was inserted in the machine. 529 Print drum lock sensor is OFF when the print drum was inserted in the machine (time-out: 5 seconds). 530 Print drum connection signal does not go OFF within 5 seconds after the print drum safety switch went OFF when the print drum was pulled out. |
| Remedy: | Set the print drum in the machine. |
| Error code: | D02 |
| Display: | D02-xxx Wrong-Type Print Cylinder Installed Replace with Correct Type |
| Description: | Incorrect print drum |
| Causes: | 532 Incorrect print drum is used. 580 Incorrect print drum is used. |
| Remedy: | Set correct print drum in the machine. |
| Error code: | D03 |
| Display: | D03-xxx Install Ink Cartridge |
| Description: | Ink cartridge not set |
| Causes: | 533 Bottle set switch is OFF. |
| Remedy: | Install ink cartridge in the print drum. |
| Error code: | D04 |
| Display: | D04-xxx Wrong-type Ink Cartridge Installed or Cannot Read Ink Info Replace Ink Cartridge or Contact dealer/Riso office |
| Description: | Incorrect ink cartridge |
| Causes: | 534 Incorrect ink cartridge is used. 560 Ink RF-Tag is not detected on ink bottle. 561 Ink RF-Tag communication error (communication with the ink cartridge was interfered by noise). 562 Wrong ink cartridge information on the Ink RF-Tag. 564 Detected a mismatch in the Ink RF-Tag. 575 RF-Tag software error. |
| Remedy: | Replace with correct ink cartridge. |
| Error code: | D05 |
| Display: | D05-xxx Set Master in Place |
| Description: | Master not set |
| Causes: | 210 Master detection sensor is OFF (not detecting master material). |
| Remedy: | Insert leading edge of the master material into the master entrance and close the master making unit. |
| Error code: | D07 |
| Display: | D07-xxx Set Master Disposal Box in Place |
| Description: | Master disposal box not set |
| Causes: | 310 Master disposal box safety switch is OFF. (Does not detect the error during low-power mode in which 24V power is down) |
| Remedy: | Set master disposal box in the machine. |
| Error code: | D08 |
| Display: | D08-xxx Set Master Making Unit in Place |
| Description: | Master making unit not set |
| Causes: | 224 Master making unit is not set (both the safety switch and lock sensor are OFF). 226 Master making unit safety switch is still OFF when the master making unit is set in position. 227 Master making unit lock sensor is still OFF when the master making unit is set in position (timeout: 5 seconds). 228 Master making unit lock sensor is still ON even after the master making unit safety switch went OFF, when the master making unit was pulled out of the machine. |
| Remedy: | Insert the master making unit in the machine. |
| Error code: | D09 |
| Description: | Master making unit cover is not closed |
| Causes: | 212 Master making unit cover set sensor is OFF. |
| Remedy: | Close the master making unit cover. |
| Error code: | D11 |
| Description: | Front cover not closed |
| Causes: | 535 Front cover set sensor is OFF. |
| Remedy: | Close the front cover of the machine. |
| Error code: | D13 |
| Display: | D13-xxx Rear Cover of Main Body is Off Call Service |
| Description: | Rear cover not closed |
| Causes: | 009 The rear cover is opened (serviceman safety switch is OFF). |
| Remedy: | Close the rear cover of the machine to activate the rear cover (serviceman safety) switch. [Field serviceman has to close and screw-on the rear cover] |
| Error code: | D17 |
| Display: | D17-xxx Wrong-type Master Installed or Cannot Read Master Info Replace Master Roll or Contact dealer/Riso office |
| Description: | Incorrect master roll |
| Causes: | 236 Incorrect master roll. 237 Master roll RF-Tag not detected. 238 Master roll RF-Tag communication error. (Communication interrupted by noise) 239 Incorrect information on the Master roll RF-Tag. 241 Mismatch in the Master roll RF-Tag information. 256 Master roll RF-Tag software error. |
| Remedy: | Set correct master roll in the machine. |
| Error code: | D18 |
| Description: | Print cylinder (drum) is ready for removal |
| Causes: | 522 Print Cylinder (Drum) is unlocked for its removal. (Drum lock Solenoid is ON). |
| Remedy: | Pull out the print Cylinder (Drum). |
| Error code: | D19 |
| Description: | Master making unit is ready for removal |
| Causes: | 223 Master making unit is unlocked for its removal. (Lock Solenoid is ON). |
| Remedy: | Pull out the master making unit. |
| Error code: | D20 |
| Description: | Master-making unit drawer cover not in position |
| Causes: | 254 The master-making unit drawer cover is not in position. (Master-making unit removed (second master-loading position sensor: ON or master-making unit pullout position sensor: ON) and cover safety SW: OFF) |
| Remedy: | Master-making unit drawer cover safety SW: OFF -> ON |
| Error code: | D21 |
| Description: | Master-making unit drawer cover may now be opened |
| Causes: | 255 The master-making unit drawer cover may now be opened. (Master-making unit pull-out position sensor: ON and Cover safety SW: ON) |
| Remedy: | Master-making unit drawer cover safety SW: ON -> OFF Or Pull-out position sensor: ON -> OFF |
| Error code: | D22 |
| Description: | Print cylinder (drum) removal command |
| Causes: | 540 Cannot access to the EEPROM on the print drum PCB. 542 Print drum PCB EEPROM data error. |
| Remedy: | Pull out print cylinder (drum) from the machine. |
| Error code: | D28 |
| Description: | DtoP cancellation due to missing first print drum |
| Causes: | 573 The print drum required for DtoP is not installed. |
| Remedy: | Print drum detection. |
| Error code: | D30 |
| Description: | Front cover setting demand |
| Causes: | 576 The front cover is not in position when a single print drum is set into place in position and the print drum removal button is pressed without the print drum at position B. |
| Remedy: | Front cover SW: ON |
| Error code: | D41 |
| Description: | Second print drum not installed |
| Causes: | 526 The print drum has been pulled out. (The connection signal, safety SW, and lock sensor are OFF.) 527 The print drum connection signal is OFF after the print drum is installed. 528 The print drum safety switch is OFF after the print drum is installed. 529 The print drum lock sensor is OFF after the print drum is installed (time-out during insertion: 5 sec). 530 The print drum connection signal does not switch OFF within 5 seconds after the print drum safety switch switched OFF when the print drum is removed. |
| Remedy: | Second print drum safety SW: ON, second print drum connection signal: ON, and second print drum lock sensor: ON << Install the print drum to clear the error. >> |
| Error code: | D42 |
| Description: | Second print drum incompatibility |
| Causes: | 532 The print drum is incompatible. |
| Remedy: | Replace with the correct print drum. (The print drum code must match the machine model.) |
| Error code: | D43 |
| Description: | Second ink cartridge not installed |
| Causes: | 533 The ink cartridge set switch is OFF. |
| Remedy: | Second ink cartridge set SW: ON |
| Error code: | D44 |
| Description: | Second ink cartridge incompatibility |
| Causes: | 534 The ink cartridge is incompatible. 560 Error due to missing ink cartridge tag. 561 Ink tag communication error (tag communication error due to noise). 562 Abnormal ink tag information. Checksum error, verification error, storage of master information, etc. 564 Serial number mismatch detected during periodic ink tag serial number check. 575 Software error involving ink tag. Antenna CH selection error, erroneous writing of data to write-protected area. |
| Remedy: | Replace with the correct ink cartridge. |
| Error code: | D47 |
| Description: | Second master disposal box not installed |
| Causes: | 310 The master disposal box safety switch is OFF. |
| Remedy: | Second master disposal box safety SW: ON << Install the master disposal box to clear the error. >> |
| Error code: | D58 |
| Description: | Second print drum pull-out possible |
| Causes: | 522 The print drum is in the pull-out position. (The print drum lock solenoid is ON.) |
| Remedy: | Second print drum connection signal: ON -> OFF and second print drum safety SW: ON -> OFF << Pull out the print drum to clear the error. >> Or front cover SW: ON << Close the front cover to clear the error. >> Or master-making unit release button: ON << Press the master-making unit release button to clear the error. >> |
| Error code: | D62 |
| Description: | Second print drum pull-out command |
| Causes: | 531 The print drum lock sensor is ON when the print drum lock solenoid is ON. (The check is performed 100 ms after the print drum lock solenoid switches ON.) 540 Data cannot be written to or read from the EEPROM inside the print drum. (EEPROM cannot be accessed.) 542 CRC error in the EEPROM inside the print drum (data error in the EEPROM). 577 The print drum is not set into position correctly (print drum radius difference). |
| Remedy: | Second print drum safety SW: OFF; second print drum connection signal: OFF; and second print drum lock sensor: OFF |
| Error code: | D68 |
| Description: | DtoP cancellation due to missing second print drum |
| Causes: | 573 The print drum required for DtoP is not installed. |
| Remedy: | Print drum detection. |
| Error code: | E01 |
| Description: | Paper leading edge not reaching the exit sensor |
| Remedy: | Is the fuser motor rotating? Y: Is the harness between the LGC board and the exit sensor open-circuited? Is the connector of the paper exit sensor or the connector J123 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the exit sensor. 2. Replace the LGC board. N: Is the harness between the LGC board and the paper exit sensor open-circuited? Is the fuser motor connector or the connector J122 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the fuser motor. 2. Replace the LGC board. Where was the paper stopped? Near the exit sensor (paper not damaged) Are the registration seRemove the paper after the fuser unit cools down.nsor and paper exit sensor functioning properly? (Does the actuator return normally?) Y: 1. In the tRemove the paper after the fuser unit cools down.est mode (03) check if each sensor is functioning. 2. Reconnect each sensor connector. N: Repair the actuator if it has come off. Before reaching the fuser unit Did the paper stop, curling upward excessively? Y: Replace the paper in the cassette. From the transfer belt surface to the exit sensor Do the size of paper and the size set match? N: Make the sizes match. Y: Is the transfer belt moving? Is the black drum motor or the transfer belt motor stopped? Or is any abnormal noise heard from one of them due to loss of synchronism? Y: 1. Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. 2. Check the motor connector, and the connector J130 on the LGC board. 3. Replace the motor. 4. Replace the LGC board. No paper found Is the paper attached to the fuser belt? Remove the paper after the fuser unit cools down. |
| Error code: | E02 |
| Display: | E02-xxx !!Maintenance!! Call Service |
| Description: | Paper trailing edge not passing the exit sensor |
| Remedy: | Is the fuser motor rotating? Y: Is the harness between the LGC board and the exit sensor open-circuited? Is the connector of the paper exit sensor or the connector J123 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the exit sensor. 2. Replace the LGC board. N: Is the harness between the LGC board and the paper exit sensor open-circuited? Is the fuser motor connector or the connector J122 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the fuser motor. 2. Replace the LGC board. Where was the paper stopped? Near the exit sensor (paper not damaged) Are the registration seRemove the paper after the fuser unit cools down.nsor and paper exit sensor functioning properly? (Does the actuator return normally?) Y: 1. In the tRemove the paper after the fuser unit cools down.est mode (03) check if each sensor is functioning. 2. Reconnect each sensor connector. N: Repair the actuator if it has come off. Before reaching the fuser unit Did the paper stop, curling upward excessively? Y: Replace the paper in the cassette. From the transfer belt surface to the exit sensor Do the size of paper and the size set match? N: Make the sizes match. Y: Is the transfer belt moving? Is the black drum motor or the transfer belt motor stopped? Or is any abnormal noise heard from one of them due to loss of synchronism? Y: 1. Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. 2. Check the motor connector, and the connector J130 on the LGC board. 3. Replace the motor. 4. Replace the LGC board. No paper found Is the paper attached to the fuser belt? Remove the paper after the fuser unit cools down. |
| Error code: | F01 |
| Display: | F01-xxx No Master on Print Cylinder (Drum) Make a New Master |
| Description: | • No master is detected on the print drum at the start of printing. |
| Causes: | • No master is detected on the print drum at the start of printing. |
| Remedy: | The warning display can be cleared by any of the following: • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | F02 |
| Description: | Master image larger than paper size: 1 |
| Causes: | 018 Paper size does not match with the image size on the print drum at the start of printing. The paper size is smaller than the image size on the master. |
| Remedy: | Press [OK] or [Cancel] button. Also check the paper size. |
| Error code: | F03 |
| Description: | Multi-up printing - Incorrect paper size |
| Causes: | 016 Tried to make multi-up printing with incorrect paper size. |
| Remedy: | Press reset key and place correct size papers on the paper feed tray. |
| Error code: | F05 |
| Display: | F05-xxx Enter Print Quantity Over The Programmed Minimum Value |
| Description: | Print quantiy under Minimum Print Quantity |
| Causes: | 019 In master making, the print quantity selected is less than the minimum print quantity. |
| Remedy: | Enter print quantity value over the programmed minimum value. |
| Error code: | F10 |
| Description: | HDD formatting error |
| Causes: | 021 Paper size does not match with the size of image on the print drum when test print is selected and activated. |
| Remedy: | (1) Format the HDD. (Enter "2" into 08-690) (2) Check if the HDD is mounted. (3) Check if the specified HDD is mounted. (4) Check if the connector pins of the HDD are bent. (5) Check if the power supply connector is disconnected. (6) Check if the connector J144 on the SYS board is disconnected. (7) Replace the HDD. (8) Replace the SYS board. (9) Replace the harness. * When changing a HDD, do the following operations after replacing a new one. 1. Formatting of the HDD <Procedure> (1) Turen ON the power while the digital keys [0] and [8] are pressed simultaneously. (2) Confirm that "Test Mode" is displayed on the control panel. Enter the code "690" and press the [START] key. The display changes to "System Mode". (3) Enter "2" and press the [SET] or [INTERRRUPT] key. (4) [WAIT] is displayed. (5) Turn OFF the power after the message [REBOOT THE MACHINE] is displayed. 2. Downloading of the UI data |
| Error code: | F24 |
| Description: | Auto Reproduction Size Selection Not Possible |
| Causes: | 037 The reproduction ratio does not match. |
| Remedy: | Press [STOP] key |
| Error code: | F30 |
| Description: | Possible Multiple Paper Feed |
| Causes: | 425 Multiple paper feed is detected on the first paper fed through. 426 Multiple paper feed is detected on the paper just fed through. (Other than the 1st paper.) |
| Remedy: | Press [STOP] key |
| Error code: | F32 |
| Description: | Storage Data - Storage Area Full |
| Causes: | 713 The DM-128 card became full while saving data. |
| Remedy: | Press [STOP] key |
| Error code: | F37 |
| Description: | Book mode: AF cannot be used |
| Causes: | 050 Original was set on the AF with book mode selected in master making. |
| Remedy: | Place original on the stage glass. |
| Error code: | F43 |
| Description: | Data printing / Paper size mismatch |
| Causes: | 902 Original size is larger than the paper size. |
| Remedy: | Check paper size, press Cancel or Continue key. |
| Error code: | F44 |
| Description: | Auto Reproduction Size - Error Between Original Size and Paper Size |
| Causes: | 901 Original size could not be detected (original size out of the specification). |
| Remedy: | Press [CANCEL] button. |
| Error code: | F45 |
| Description: | Original Undetected |
| Causes: | 954 Auto-tray or Auto-reproduction size is selected, and master making or print to linked printer is started with original undetected 959 Master making or print to a linked printer is started with original undetected. 981 The original not detected when [NEXT] button was pressed in Multi-Up Wizard display. |
| Remedy: | Reset the original in place. |
| Error code: | F46 |
| Description: | Inconsistency of first print drum color between DtoP job and specified color |
| Causes: | 903 The color of the print drum fails to match between the color specified for DtoP job and the color set for the specified print mode. |
| Remedy: | Press the Reset key or the Continue button. (Replace the print drum.) |
| Error code: | F47 |
| Description: | AF - card size reproduction not available |
| Causes: | 904 Reproduction size from A4 size reduced to card size is selected and the original is placed on the AF unit. |
| Remedy: | Remove original from AF and set it on the stage glass. |
| Error code: | F48 |
| Description: | Multi-Up - Wrong Original Size |
| Causes: | 955 During the multi-up operation, the original size was detected as customs size or out of specification. |
| Remedy: | Press [STOP] key. |
| Error code: | F49 |
| Description: | Multi-Up - No Original |
| Causes: | 989 The original was undetected when Multi-Up operation was selected for either one original or multi-original. |
| Remedy: | Press [STOP] key |
| Error code: | F52 |
| Description: | Printing from Linked Printer disabled - Printer data not received |
| Causes: | 912 Printing from linked printer disabled (Linked printer data not received). |
| Remedy: | Press the [CLOSE] button. |
| Error code: | F58 |
| Description: | Printing from Linked Printer Disabled - Initializing NET-C |
| Causes: | 927 Printing from Linked Printer disabled (NET-C/D being initialized). |
| Remedy: | Press the [CLOSE] button. |
| Error code: | F60 |
| Description: | [Printer-Auto-Selection disabled: Print quantity selected is 0 |
| Causes: | 929 Auto-printer-selection is disabled with print quantity selected as Zero. |
| Remedy: | Press either [OK] or [Cancel] button. |
| Error code: | F61 |
| Description: | Linked Printer - Wrong Paper Size |
| Causes: | 930 Original size does not match with the paper size set on the linked printer. |
| Remedy: | Press [CANCEL] button. |
| Error code: | F62 |
| Description: | Printer-Auto-Selection disabled - Linked printer error |
| Causes: | 956 Auto-printer-selection is disabled due to linked printer error. |
| Remedy: | Press [Cancel] button. |
| Error code: | F63 |
| Description: | Linked Printer - Auto Tray Selection not avaialble for Irregular Size Original |
| Causes: | 971 Auto-Tray-Selection was used in printing from the linked printer using irregular sized original. |
| Remedy: | Press [CANCEL] button |
| Error code: | F64 |
| Description: | Selected Function Not Available While Processing Print Data from PC |
| Causes: | 964 Scanning, Overlay, Digitizer or Hold function was selected while the printer is receving data from PC. |
| Remedy: | Press {CLOSE] button. |
| Error code: | F65 |
| Description: | Scan Mode - Auto Page Size Selection Not Available for Irregular Size Original |
| Causes: | 965 The auto-size (save data) selection at start of scanning is detected as original irregular in size. |
| Remedy: | Press [RESET] key. |
| Error code: | F66 |
| Description: | Linked printer saddle stitching is disabled |
| Causes: | 962 Specified tray does not have any A3 (Ledger), B4 (Legal), A4 (Letter) or A4L (Letter-L) when printing from linked printer with saddle stitching selected. |
| Remedy: | Press [Close] button. |
| Error code: | F67 |
| Description: | Linked printer saddle stitching is disabled |
| Causes: | 963 Specified size papers are not set in horizontal and vertical directions in the linked printer tray, when printing from linked printer with rotation sorting selected. |
| Remedy: | Press [Close] button. |
| Error code: | F68 |
| Description: | Specified area/traced color separation: Excess number of specified areas |
| Causes: | 173 The number of specified areas for specified area/traced color separation exceeded the maximum value. |
| Remedy: | Press the Reset key. |
| Error code: | F69 |
| Description: | Specified area/traced color separation: Distance of border for specified area longer than master-making size |
| Causes: | 174 The distance of the border of the specified area for specified area/traced color separation exceeds the value corresponding to the master being made. |
| Remedy: | Press the Reset key. |
| Error code: | F70 |
| Description: | Specified area/traced color separation: Image processing time-out error |
| Causes: | 175 Image processing time-out error during specified area/traced color separation. |
| Remedy: | Press the Reset key. |
| Error code: | F71 |
| Description: | No master on second print drum |
| Causes: | 015 No master is found on the print drum at the start of printing. |
| Remedy: | Press the Reset key. Set an original and execute the master-making operation. |
| Error code: | F72 |
| Description: | Hand-written/red-color separation: Image processing time-out error |
| Causes: | 176 Image processing time-out error during hand-written/hand-written (ink)/red-color separation. |
| Remedy: | Press the Reset key. |
| Error code: | F73 |
| Description: | Linked Printer - Auto Tray Selection Not Available with Selected Reproduction Ratio |
| Causes: | 975 In Linked Printer printing, the detected original size does not match with the selected reproduction size. |
| Remedy: | Press [STOP] key. |
| Error code: | F74 |
| Description: | High Speed Printing - Printer Temperature is Too Low for 180 ppm High Speed Printing |
| Causes: | 980 High speed printing was selected with the machine temperature below 15 degrees Celcius. |
| Remedy: | Press [STOP] or [START] key. |
| Error code: | F75 |
| Description: | Combined use of specified area separation and AF not possible |
| Causes: | 982 With specified area separation set, an original was on the AF at the start of master-making. |
| Remedy: | Press the Reset key. |
| Error code: | F76 |
| Description: | Second print drum color not matching with DtoP job color |
| Causes: | 903 The color of the print drum to be used fails to match for the DtoP job and the specified print mode. |
| Remedy: | Press the Reset key or Continue button. (Replace the print drum.) |
| Error code: | F77 |
| Description: | Print drum color not matching with DtoP job color |
| Causes: | 903 The color of the print drum to be used fails to match for the DtoP job and the specified print mode. |
| Remedy: | Press the Reset key or Continue button. (Replace the print drum.) |
| Error code: | F78 |
| Description: | Editor - Stage Cover is Opened |
| Causes: | 731 The stage cover is opened during the digitizer operation. |
| Remedy: | Close the stage cover and press [CLOSE] button. |
| Error code: | F79 |
| Description: | Editor - No Original During Re-Scanning |
| Causes: | 732 The original was not detected during re-scanning. |
| Remedy: | Press [STOP] key |
| Error code: | F80 |
| Description: | Paper not compatible with dual-color printing |
| Causes: | 966 The paper size is smaller than the minimum paper size for dual-color printing. |
| Remedy: | Press the Reset key. (Use paper larger than the minimum size.) |
| Error code: | F81 |
| Description: | Dual-color printing: Ink-saving setting only for one print drum |
| Causes: | 967 At the start of dual-color printing operation, the master was made with one print drum in ink-saving master-making mode and the other in normal master-making mode. |
| Remedy: | Press the Stop button or Continue button. |
| Error code: | F82 |
| Description: | Paper not compatible with printing by second print drum |
| Causes: | 974 The paper size is smaller than the minimum paper size for printing with the second print drum. |
| Remedy: | Press the Reset key. |
| Error code: | F83 |
| Description: | Use of second print drum mode not possible |
| Causes: | 973 There is no confidential master on the first print drum at the start of printing/proof-printing operation with the second print drum. |
| Remedy: | Press the Reset key. |
| Error code: | F85 |
| Description: | External CI - Scanning Not Possible with External CI not Connected |
| Causes: | 995 Either the PS7R is not connected or improperly connect. |
| Remedy: | Press [CLOSE] button or press [START] key. |
| Error code: | F90 |
| Description: | Ink Supply Stock Inventory |
| Causes: | 957 Set quantity of the specified color ink stock quantity is equal to or less than the calculated stock quantity. |
| Remedy: | Press [CLOSE] button. |
| Error code: | F91 |
| Description: | Master Roll Supply Stock Inventory |
| Causes: | 958 Set quantity of the specified master roll stock quantity is equal to or less than the calculated stock quantity. |
| Remedy: | Press [CLOSE] button. |
| Error code: | H01 |
| Description: | General supply parameter input (first print drum) |
| Causes: | 566 Enter parameters, since first ink tag color information, steady-state viscosity information, and FP viscosity information are unreliable. |
| Remedy: | Enter the parameters and press the Start key. |
| Error code: | H04 |
| Description: | General supply parameter input (master) |
| Causes: | 242 Enter parameters, since master tag sensitivity information, steady-state viscosity information, and FP viscosity information are unreliable. |
| Remedy: | Enter the parameters and press the Start key. |
| Error code: | H07 |
| Description: | General supply parameter input (second print drum) |
| Causes: | 571 Enter parameters, since second ink tag color information, steady-state viscosity information, and FP viscosity information are unreliable. |
| Remedy: | Enter parameters and press the Start key. |
| Error code: | T01 |
| Description: | Main motor lock |
| Causes: | 520 Main encoder sensor does not go ON/OFF within 10 milliseconds after the main motor activates. 520 Main motor lock detection due to main motor FG sensor count reduced to 50% of the set speed. (The detection is not made for the first 2 seconds from the main motor movement.) 521 B-positioning sensor status does not change even after 3,033 pulses after the main motor activates. 524 Clamp unit is not at the home position while the print drum is in operation (except during master disposal). 537 Print drum failed to stop at position B. 538 Print drum is not locked during operation. (Drum lock sensor: OFF) |
| Remedy: | Press Reset Key |
| Error code: | T02 |
| Description: | Elevator motor lock |
| Causes: | 400 Both the upper and lower limit sensors are ON at the same time. 401 Overload current was detected in the elevator motor. 404 The lower-limit sensor does not go OFF within 2 seconds after the elevator motor operates in the raising direction from the lower-limit position. 405 The upper-limit sensor does not go ON within 12 seconds after the elevator motor operates in the raising direction. 406 The upper-limit sensor does not go OFF within 2 seconds after the elevator motor operates in the lower direction from the upper-limit position. 407 The lower-limit sensor does not go ON within 12 seconds after the elevator motor operates in the lowering direction. 408 The upper-limit sensor is OFF continuously for over 2 seconds during operation of the elevator servo action to raise the feed tray. |
| Remedy: | Press Reset Key or turn OFF and ON the power. |
| Error code: | T03 |
| Description: | Clamp motor lock |
| Causes: | 500 Clamp sensor A is OFF after the completion of the clamp unit initialization or home positioning movement. 501 Clamp sensor B does not change within 1 second from the time the clamp motor operates in the forward direction. 502 Clamp sensor B does not change within 1 second from the time the clamp motor operates in the reverse direction. 503 Clamp sensor A does not go ON within 3 seconds when the clamp unit makes initialization movement. 504 At the start of Clamp plate open/close action, the detection sequence of clamp-sensors A & B are abnormal. 505 At the start of print drum Position-A compensation movement, the detection sequence of clamp-sensors A & B are abnormal. 506 At the start of Clamp unit Home-positioning movement, the detection sequence of clampsensors A & B are abnormal. 507 Clamp sensor A is ON after the clamp release action is completed. 508 Clamp sensor A is ON after the A-position compensating movement is completed. 545 Clamp unit is not in the home position while the print drum is in movement (cause due to the clamp motor). |
| Remedy: | Press Reset Key |
| Error code: | T04 |
| Description: | Ink overflow |
| Causes: | 513 The overflow sensor is ON for a set number of times in succession during the 10- millisecond-interval overflow-sensor check. |
| Remedy: | Press Reset Key after correcting the ink overflow condition. (No ink on the ink overflow sensor.) |
| Error code: | T05 |
| Description: | Vertical print positioning pulse motor lock |
| Causes: | 603 The vertical-centering sensor does not switch ON even when the vertical-positioning pulse motor activated in the image-down direction for 5.0 seconds during vertical home positioning movement. 603 The vertical-centering sensor does not switch ON even when the vertical-positioning pulse motor activated in the image-down direction for 5.5 seconds during vertical home positioning movement. 603 The vertical-centering sensor does not switch ON even when the vertical-positioning pulse motor activated in the image-down direction for regulation time during vertical home positioning movement. 604 The vertical-centering sensor does not switch OFF even when the vertical-positioning pulse motor activated in the image-up direction for 5.0 seconds during vertical home positioning movement. 604 The vertical-centering sensor does not switch OFF even when the vertical-positioning pulse motor activated in the image-up direction for 5.5 seconds during vertical home positioning movement. 604 The vertical-centering sensor does not switch OFF even when the vertical-positioning pulse motor activated in the image-up direction for regulation time during vertical home positioning movement. 605 Even though the vertical positioning motor stopped according to the vertical centering sensor detection, the stopping position does not correspond with the programmed position. (GA control error). 612 The print positioning key is pressed with vertical-print-position information undefined. 619 The vertical positioning motor does not end its operation within the set period during the recovery movement to rotate -98 pulses. 632 The vertical positioning motor does not end its operation within the set period in the pulse count stop mode, or in the sensor stop mode after the actuator is detected by the sensor. |
| Remedy: | Press Reset Key or turn the power OFF and ON. |
| Error code: | T06 |
| Description: | Print drum horizontal pulse motor lock |
| Causes: | 607 The actuator plate does not escape from the horizontal HP sensor when the print drum slides to the right during the horizontal HP movement. 608 The actuator plate does not escape from the horizontal HP sensor when the print drum slides to the left during the horizontal HP movement. 609 Even though the horizontal positioning pulse motor stopped after the sensor stop mode, the sensor detection status did not match with the programmed status. 611 Timeout error during print drum horizontal movement. 617 Horizontal movement system information error. 618 The clamp unit is not in its HP position when the print drum starts its horizontal movement. 633 The horizontal positioning pulse motor does not end its operation within the set period in the pulse count stop mode, or in the sensor stop mode after the actuator is detected by the sensor. |
| Remedy: | Press Reset Key or turn the power OFF and ON. |
| Error code: | T11 |
| Description: | Print pressure pulse motor lock |
| Causes: | 600 Print pressure HP sensor does not switch ON within 5 seconds after the print pressure pulse motor activated towards higher pressure during home positioning operation. 600 Print pressure HP sensor does not switch ON within 3.9 seconds after the print pressure pulse motor activated towards higher pressure during home positioning operation. 601 Print pressure HP sensor does not switch OFF within 5 seconds after the print pressure pulse motor activated towards lower pressure during home positioning operation. 601 Print pressure HP sensor does not switch OFF within 4.6 seconds after the print pressure pulse motor activated towards lower pressure during home positioning operation. 602 Even though the print pressure control pulse motor stopped according to the print pressure HP sensor detection, the stopping position does not correspond with the programmed position. (GA control error). 614 Print pressure pulse motor does not complete its movement even after 7 seconds from the print pressure HP movement to move -1000 pulses. 614 Print pressure pulse motor does not complete its movement even after 1.2 time the set period passed from the print pressure HP movement to move -1000 pulses. 631 The print pressure pulse motor does not end its operation within the set period in the pulse count stop mode, or in the sensor stop mode after the actuator after the actuator is detected by the sensor. |
| Remedy: | Press Reset Key or turn the power OFF and ON. |
| Error code: | T12 |
| Description: | Master disposal area motor lock |
| Causes: | 300 Overload current was detected in the master disposal motor. 301 Master compression motor lock when moving compression plate up. 305 Master compression sensor does not go ON within 6.5 seconds after the master compression motor operates in the return direction. 305 Master compression sensor does not go ON within 7.5 seconds after the master compression motor operates in the return direction. 306 Master compression sensor does not go OFF within 2 seconds after the master compression motor operates in the compress direction. 307 Master compression plate maximum position is not detected within 6.5 seconds after the master compression motor operates in the compress direction. 307 Master compression plate maximum position is not detected within 7.5 seconds after the master compression motor operates in the compress direction. 309 The FG sensor status on the master compression motor does not change even after 2 seconds from the motor activation. 309 Master-compression-motor encoder sensor count did not change as the master compression motor activated in the compress direction and moved out from the home position. 309 The FG sensor status on the master compression motor did not change for 50 consecutive times during 10 millisecond polling. 316 Master-compression-motor encoder sensor count did not change within 10 milliseconds after the master compression motor activated. 316 The master-disposal-motor FG sensor count dropped to 50% of the set speed. (The speed check starts 2 seconds after the activation of the motor.) |
| Remedy: | Press Reset Key. |
| Error code: | T13 |
| Description: | Cutter motor lock |
| Causes: | 203 Cutter HP switch does not go OFF within 100 milliseconds after the cutter motor is activated. 204 Cutter HP switch does not go ON within 300 milliseconds after the cutter motor is activated. 205 Master-positioning sensor is ON when the print drum rotates through the preset angle following master cutting. 222 Cutter HP switch does not go ON within 450 milliseconds after the cutter home positioning operation started. |
| Remedy: | Press Reset Key. |
| Error code: | T14 |
| Description: | Flatbed error |
| Causes: | 112 The scanner HP sensor does not go OFF within given time. 113 The scanner HP sensor does not go ON within given time. 114 Incorrect main-unit data. 115 The scanner operation is not completed within the set time. 116 Timeout error for black shading compensation. 117 Timeout error for white shading compensation. 118 Software error 123 Offset adjustment not completed within set time. 124 Gain adjustment not completed within set time. 125 Offset adjustment not completed. 126 Gain adjustment not completed. 135 Malfunction detected during offset adjustment. 136 Malfunction detected during gain adjustment. 137 Malfunction detected during black shading compensation. 138 Malfunction detected during white shading compensation. 160 The scanner model information is missing. 170 Even though the read pulse motor stopped according to the sensor detection, the stopping position does not correspond with the programmed position. (GA control error). |
| Remedy: | Press Reset Key. |
| Error code: | T15 |
| Description: | AF error |
| Causes: | 100 AF original IN sensor adjustment error. 101 AF-EEPROM error. 110 ABC (auto-base-control) timeout. The original does not move from the ABC scanning position on the AF unit. 111 Operation command was made to the AF unit without 24 volts supplied to the AF unit. 130 Timeout error in receiving reply from the AF unit after command signal was sent from the Riso printer to the AF unit. 131 Riso printer received an undefined command from the AF unit. 132 Riso printer detected communication sequence error from the AF unit. 133 Communication error with AF unit (ACK, NAK, or receiving channel error). 134 Riso printer could not send command to the AF unit within the set time. 161 AF unit not connected. |
| Remedy: | Turn OFF and ON the power. |
| Error code: | T17 |
| Description: | Solenoid counter not connected |
| Causes: | 020 Solenoid counter is not connected. |
| Remedy: | Connect the solenoid counter. |
| Error code: | T19 |
| Description: | Thermal-pressure motor lock |
| Causes: | 207 TPH pressure sensor does not go OFF within 2 seconds after the thermal-pressure motor activates in the decompressing direction, or during home positioning operation. 208 TPH pressure sensor does not go ON within 2 seconds after the thermal-pressure motor activates in the decompressing direction. 216 TPH pressure sensor does not go OFF within 2 seconds after the thermal-pressure motor activates in the compressing direction. 217 TPH pressure sensor does not go ON within 2 seconds after the thermal-pressure motor activates in the compressing direction. |
| Remedy: | Press Reset key |
| Error code: | T20 |
| Description: | Paper-ejection-section motor lock |
| Causes: | 414 Paper ejection wing HP sensor status does not change within set time after the paper ejection wing motor activated for the wing home position movement. 415 Paper-ejection-wing home sensor does not go OFF within 7 seconds after the paper ejection wing motor activates in the clockwise direction from the home position. 415 The paper ejection wing HP sensor does not change from OFF to ON even though the paper ejection wing pulse motor is activated for a given time. 416 Overload current was detected in the paper-ejection motor. 437 Paper-ejection encoder sensor status does not change within 10 milliseconds after the paper-ejection motor is activated. 437 The paper ejection motor FG sensor pulse count dropped to 50% of the set speed. (The detection starts 2 seconds after the paper ejection motor is activated.) 442 Even though the paper ejection pulse motor stopped after the sensor stop mode, the sensor detection status did not match with the programmed status, or the motor does not stop within the set time in the pulse count stop mode. 442 Though the paper ejection wing motor stopped correctly at the wing sensor position, the stopping position does not correspond with the programmed position (GA control error). 456 The paper ejection pulse motor does not end its operation within the set period in the pulse count stop mode, or in the sensor stop mode after the actuator is detected by the sensor. |
| Remedy: | Press Reset key |
| Error code: | T24 |
| Description: | Inking motor lock |
| Causes: | 539 Inking-motor FG sensor status does not change within 20 milliseconds after the inkingmotor is activated. |
| Remedy: | Press Reset key or turn the power OFF and ON. |
| Error code: | T25 |
| Description: | Replace Battery |
| Causes: | 026 Battery voltage is too low when the power is turned ON. (Readjust the machine clock after replacing the battery.) |
| Remedy: | Replace the battery. |
| Error code: | T27 |
| Description: | Master-making unit motor lock |
| Causes: | 249 The light path of the master-making unit pull-out position sensor was not blocked within the set time when the master-making unit moved to the pull-out position. 251 Although the master-making unit transport pulse motor has completed the operation in sensor stop mode, the logical value of the sensor at the arrival point does not match the design value. Or the operation fails to complete in counter stop mode within the specified time (faulty gate array control). 252 The pressure plate of the master-making unit opens at a location other than the master-making unit pullout position. 248 The master-making unit position sensor does not change status as specified within the set time after the master-making unit begins moving to the standby position. 250 The master-making unit position sensor does not change status as specified within the set time after the master-making unit begins moving to the master-making position. |
| Remedy: | Press the Reset key. |
| Error code: | T29 |
| Display: | T29-Temp Sensor Error |
| Description: | Temp Sensor Failure The Temperature Sensor has failed. |
| Causes: | • Temp/Humidity Sensor, PL8.1.80 • ENV Harness, PL8.1.81 • Engine Control Board, PL1.1.4 |
| Remedy: | 1 Test the Temp/Humidity Sensor. 1. Run the Service Diagnostics Ambient Temp/Hum Sensor test. 2. Verify proper operation by blowing on the sensor. Is the sensor operating correctly? Replace the Engine Control Board. Go to Step 2. 2 Replace the Temp/Humidity Sensor. Does the error persist? Go to Step 3. Complete. 3 Check the ENV harness connection. Is the ENV Harness connected? Go to Step 4. Reconnect the harness. 4 Check all pins on the ENV Harness for continuity. 1. Disconnect ENV and P/J420. 2. Check continuity between ENV <=> J420. Go to Step 5. Replace the ENV Harness. 5 Check the Temp/Humidity Sensor signal. Is there voltage present at FSNS-17 when the sensor is active? Go to Step 6. Replace the Front Sensor Board. 6 Check all pins on the FSNS Harness PL4.2.98 for continuity. 1. Disconnect FSNS. 2. Check continuity on all contacts. Replace the Motor Driver Board. Replace the FSNS Harness. |
| Error code: | T31 |
| Display: | T31-Roller Over Error |
| Description: | The fuser temperature sensor is reporting a temperature error. Turn off the printer, wait 15 seconds, then turn on the printer. If the problem persists, install a new fuser |
| Causes: | 445 The central flap home position sensor detects no light within the set time after the central flap motor begins operating. 446 The light path of the central flap home position sensor is not blocked within the set time after the central flap motor begins operating. 451 Overload current detected in the central flap motor. The central flap motor overcurrent port switches ON 20 consecutive times (polling at 10-msec intervals). |
| Remedy: | 1. Inspect the fuser cooling fan. Ensure it is running correctly and is not blocked. 2. Remove and install the fuser. 3. Test the thermistor inside the fuser using the test described in “Switch scan test”. Replace the fuser. 5. Replace the low-voltage power supply. 6. Replace the engine controller board. |
| Error code: | T41 |
| Description: | Engine Cavity Fan Failure The rotation signal from the Card Cage Fan indicates the fan has stopped rotating. |
| Causes: | • Card Cage Fan, PL2.1.118 • Motor Driver Board, PL2.1.10 |
| Remedy: | 1 Test the Card Cage Fan. Run the Service Diagnostics Chassis test. Does the Fan operate correctly. Replace the Engine Control Board. Go to Step 2. 2 Check the Fan connection. Is FAN on the Motor Driver Board securely connected? Go to Step 3. Connect the Fan. 3 Check for +24 V at the Fan connector. Disconnect the Fan from FAN. Is there +24 V between FAN-1 <=> ground? Replace the Fan. Go to Step 4. 4 Check for +24 V at the POW24 connector. Disconnect the POW24 Harness from the Motor Driver Board. Is there +24 V between POW24-1 <=> ground? Replace the Motor Driver Board. Go to Step 5. 5 Check continuity of the POW24 Harness. Is the wiring harness conductive? Replace the LVPS Replace the harness. |
| Error code: | T43 |
| Description: | Clamp motor lock |
| Causes: | 500 The clamp sensor A is OFF after the clamp unit initializes and completes home position operation. 501 The clamp sensor B does not change status within 1 second after the clamp motor begins rotating in the forward direction. 502 The clamp sensor B does not change status within 1 second after the clamp motor begins rotating in the reverse direction. 503 The clamp sensor A does not switch ON within 3 seconds during clamp unit initialization. 504 The logical values of the clamp sensors A and B do not match at the start of the clamp releasing operation. 505 The logical values of the clamp sensors A and B do not match at the start of the position-A compensation operation. 506 The logical values of the clamp sensors A and B do not match at the start of the clamp unit home positioning operation. 507 The clamp sensor A is ON after completion of the clamp releasing operation. 508 The clamp sensor A is ON after completion of the position-A compensation operation. 514 The print drum is not at the horizontal home position while the clamp unit is operating. 545 The clamp unit is not at the specified position when the print drum begins rotating. 546 The clamp unit is not at the home position when the print drum initiates horizontal movement. 547 The clamp unit is not at the home position when the master-making unit begins its motion. |
| Remedy: | Press the Reset key. |
| Error code: | T44 |
| Description: | Overflow |
| Causes: | 513 The overflow sensor switches ON successively for the set number of times during the 10-ms-interval check. |
| Remedy: | With the overflow sensor switched OFF, press the Reset key. |
| Error code: | T45 |
| Description: | Print-positioning pulse motor lock |
| Causes: | 610 Time-out error generated during vertical print positioning operation. 612 The 1-step Vertical Print Positioning key was pressed with position information undefined. (This error may occur after a recovery operation.) 616 Step movement was invoked with vertical print positioning system information undefined. |
| Remedy: | Press the Reset key or switch power OFF, then ON. |
| Error code: | T46 |
| Description: | Horizontal pulse motor lock |
| Causes: | 607 The horizontal home position sensor detects no light within xx seconds after the horizontal home positioning operation initiates movement toward the right during drive releasing operation. 608 The light path of the horizontal home position sensor is not blocked within xx seconds after the horizontal home positioning operation initiates movement toward the left during drive connecting operation. 609 Although the horizontal pulse motor has completed the operation in sensor stop mode, the logical value of the sensor at the arrival point does not match the design value, or the operation fails to complete in counter stop mode within the specified time (faulty gate array control). 611 Time-out error generated during horizontal movement. 617 Step movement was invoked with horizontal system information undefined. 618 The clamp unit is not at the home position during horizontal movement. 627 The light path of the drive release home position sensor is not blocked during drive connecting operation. 628 The drive release home position sensor detects no light during drive releasing operation. |
| Remedy: | Press the Reset key or switch power OFF, then ON. |
| Error code: | T51 |
| Description: | Print pressure control pulse motor lock |
| Causes: | 600 The print pressure control sensor does not change from OFF to ON within 3.9 seconds after the print pressure control pulse motor activates to increase pressure during home positioning. 601 The print pressure control sensor does not change from ON to OFF within 4.6 seconds after the print pressure control pulse motor activates to reduce pressure during home positioning. 602 Although the print pressure control pulse motor has completed the operation in sensor stop mode, the logical value of the sensor at the arrival point does not match the design value, or the operation fails to complete in counter stop mode within the specified time (faulty gate array control). 626 Time-out error generated in print pressure relative movement (movement based on pulse count only, without sensor check). |
| Remedy: | Press the Reset key or switch power OFF, then ON. |
| Error code: | T52 |
| Description: | Master disposal section motor lock |
| Causes: | 300 Overload current detected in master disposal motor. The master disposal motor overcurrent port was ON (polling at 10-msec intervals). 301 Master compression motor lock detected. The RMGA compression detection switches ON while lifting the compression plate. 305 The master compression sensor does not switch ON within 6.5 seconds after the master compression motor initiates reciprocal motion. 306 The master compression sensor does not switch OFF within 2 seconds after the master compression motor applies a force to begin compression. 307 The compression detection does not switch ON within 6.5 seconds after the master compression motor applies a force to begin compression. 309 The FG count value does not change when the master compression motor applies a force to begin compression, moving away from the home position. (The master compression motor FG sensor does not change status.) |
| Remedy: | Press the Reset key. |
| Error code: | T64 |
| Description: | Inking motor lock |
| Causes: | 539 Inking motor lock detected. The inking motor FG sensor does not change status within 20 ms after the inking motor switches ON. |
| Remedy: | Press the Reset key or switch power OFF, then ON. |
| Error code: | T67 |
| Description: | Master-making unit motor lock |
| Causes: | 248 The master-making unit position sensor does not change status as specified within the set time after the master-making unit begins moving to the standby position. 250 The master-making unit position sensor does not change status as specified within the set time after the master-making unit begins moving to the master-making position. |
| Remedy: | Press the Reset key. |
| Error code: | T91 |
| Description: | Panel EEPROM error |
| Causes: | 968 Panel EEPROM read error. 969 Panel EEPROM write error. 976 Panel EEPROM check-sum error. 977 Panel EEPROM verify error. |
| Remedy: | Press Reset Key |
| Error code: | T92 |
| Description: | Drum EEPROM write error |
| Causes: | 570 EEPROM on the print drum PCB is being accessed while the print drum is in releasing action from the machine. |
| Remedy: | Press Reset Key |
| Error code: | T93 |
| Description: | NET-C / NET-D hardware error |
| Causes: | 932 No reply from the NET-C or NET-D network interface card while accessing to the network interface card. 933 No response from NET-C for 90 seconds during NET-C initialization. 933 No response from NET-D for 90 seconds during NET-D initialization. |
| Remedy: | Turn the power OFF and ON. |
| Error code: | T94 |
| Description: | Call service error: TPH |
| Causes: | 225 TPH code does not match with the machine code when the power is turned ON with the master-making unit in operating position or when the master-making unit is inserted in operating position while the power is ON. |
| Remedy: | Turn the power OFF and ON. |
| Error code: | T95 |
| Description: | FRAM error |
| Causes: | 059 Machine serial-number information sent from SH-PCB does not match with the machine serial number information in the MCTL PCB. |
| Remedy: | Turn the power OFF and ON. |
| Error code: | T96 |
| Description: | Data not input |
| Causes: | 171 TPH resistance value not input. 172 Scanner adjustment not completed. 433 Paper size width potentiometer test-mode setting is not completed. 452 Too small difference between the 105mm and 297mm A/D data of the paper feed tray pape 569 Either the print drum color information or ink category information is still not input. 613 Print pressure data missing. 872 MTPF Tray-1 paper width potentiometer value is not input. 873 MTPF Tray-2 paper width potentiometer value is not input. 972 REv data storage area is not initialized. |
| Remedy: | Input the parameters using test mode. |
| Error code: | T97 |
| Description: | PC card access error |
| Causes: | 939 PC card access error: PC card not set. 940 PC card access error: PCMCIA card information error. 941 PC card access error: CF card device error. 942 PC card access error: Same file already exists. 943 PC card access error: Not formatted. 944 PC card access error: Media ID error. 945 PC card access error: Media error (cannot access the PC card). 946 PC card access error: Media error (not enough blank space available on CF card). 990 PC card access error: Specified file not found on the selected drive. 991 PC card access error: Accessed to the file not opened. 992 PC card access error: File information folder is already in use. 993 PC card access error: Incorrect setting on the readout address when sending data to the machine. 994 PC card access error: Unsuccessful file deleting. |
| Remedy: | Press Reset Key |
| Error code: | T98 |
| Description: | Hardware error |
| Causes: | 002 No reply from SH PCB. If SH PCB signal is detected at machine power ON, but if the PCB communication terminates and T98-069 error is detected, the error point is rewrote to this T98-002 error message. 005 Hardware error 006 FRAM check-sum error 025 Defective RF PCB (Unsuccessful initial communication with RF PCB). 034 Unable to write on EEPROM on the machine. (Cannot access EEPROM). 035 CRC error on EEPROM on the machine (Defective EEPROM data). 038 Information between the PCB and EEPROM does not match. 039 Incorrect EEPROM. 051 Communication error with the touch-panel controller. 053 Unsuccessful data readout from the Memory setting (program, mode, user paper). 054 Unsuccessful data writing of the Memory setting (program, mode, user paper). 055 Machine code number sent from SH PCB does not match with that from the Mechanical control PCB. 063 Test mode setting is beyond the adjustable range. 064 Communication error between SH PCB and MCTL PCB. 065 Communication error between SH PCB and MCTL PCB (01) - on MCTL PCB side. 067 Communication error between SH PCB and MCTL PCB (03) - on MCTL PCB side. 068 Communication error between SH PCB and MCTL PCB (04) - on MCTL PCB side. 069 Communication error between SH PCB and MCTL PCB (05) - on MCTL PCB side. 070 Communication error between SH PCB and MCTL PCB (06) - on MCTL PCB side. 071 Communication error between SH PCB and MCTL PCB (07) - on MCTL PCB side. 072 Communication error between SH PCB and MCTL PCB (08) - on MCTL PCB side. 073 Communication error between SH PCB and MCTL PCB (09) - on MCTL PCB side. 074 Communication error between SH PCB and MCTL PCB (10) - on SH PCB side. 075 Communication error between SH PCB and MCTL PCB (11) - on SH PCB side. 076 Communication error between SH PCB and MCTL PCB (12) - on SH PCB side. 077 Communication error between SH PCB and MCTL PCB (13) - on SH PCB side. 078 Communication error between SH PCB and MCTL PCB (14) - on SH PCB side. 079 Communication error between SH PCB and MCTL PCB (15) - on SH PCB side. 080 Communication error between SH PCB and MCTL PCB (16) - on SH PCB side. 081 Communication error between SH PCB and MCTL PCB (17) - on SH PCB side. 082 Communication error between SH PCB and MCTL PCB (18) - on SH PCB side. 083 Communication error between SH PCB and MCTL PCB (19) - on SH PCB side. 084 Communication error between SH PCB and MCTL PCB (20) - on SH PCB side. 098 Machine serial number information on EEPROM does not match with that of FRAM. 119 Defective image PCB (memory check error on the image processing IC). 120 Timeout on the scanner serial communication. 129 Defective scanner gate array PCB (memory check error on the gate array). 245 Timeout error on master transfer during master-making (related to Write pulse motor). 246 Timeout error on master transfer during master-making (related to Load pulse motor). 422 The light emittance from the Paper sensor (send) exceeded the maximum allowance during the Automatic Multiple Paper Feed Adjustment [paper sensor sensitivity adjustment] by Test Mode No.705. 423 The light emittance from the Paper sensor (send) exceeded the minimum allowance during the Automatic Multiple Paper Feed Adjustment [paper sensor sensitivity adjustment] by Test Mode No.705. 921 The USB controler chip is not responding when PC and printer is connected by USB cable. 934 Communication error between MCTL PCB and RF PCB. (on FR PCB side) 935 Communication error between MCTL PCB and RF PCB. (on MCTL PCB side) 937 Undefined serial number. 938 FRAM version down. 947 24V-A does not go ON. (Possible broken Fuse for 24V-A area). 948 24V-A does not go ON. (Possible broken Fuse for 24V-B area). 949 24V-A does not go OFF. 950 24V-B does not go OFF. 952 SH3M2 PCB flash memory check-sum error. 953 Unsuccessful writing on the SH3M2 PCB flash memory. 960 Unsuccessful readout from the SH3M2 PCB flash memory. 961 SH3M2 PCB flash memory unused. 978 Incorrect power ON command from MCTL PCB when machine power turned ON. 979 Abnormal flash memory setting on the SH3M2 PCB. 983 24V-C does not go ON. (Possible broken Fuse for 24V-C area). 984 24V-C does not go OFF. |
| Remedy: | Turn power OFF and ON. |
| Error code: | T99 |
| Description: | Software error |
| Causes: | 181 Timeout on Image processing time. 982 Wrong loader. |
| Remedy: | Turn power OFF and ON. |
