Riso SF5430
Рейтинг
Модули
Exterior Cover Area
Master Making Area(1)
Master Removal Area(2)
Paper-Feed Tray
Scanner Area (1)
Drum-Rail Area
Drum Area(2)
Master Making Area(3)
Paper Receiving Tray Area
Drum Area(1)
Scraper Area
Master Removal Area(1)
Operation Panel Area
Drum Area(5)
Drum Area(3)
Separation Area
Master Making Area(2)
Master Making Area(4)
Stage Cover Area
Master Removal Area(3)
Master Making Area(6)
Drive Mechanism Area(1)
Roller System Area
Clamp Area
Drive Mechanism Area(3)
Drum Area(4)
Electrical Component Area(1)
Master Making Area(5)
Electrical Component Area(2)
Elevator-Safety SW Area
Suction Area
Scanner Area (2)
Main Body Area
Drive Mechanism Area(2)
Детали Elevator-Safety SW Area
| Деталь: | N/A |
| Парткод: | 059-34023-007 |
| Деталь: | HINGE BASE SHAFT, FRONT DOOR |
| Парткод: | 059-34026-006 |
| Деталь: | Cover Catch |
| Парткод: | 660-05106-002 |
| Деталь: | Door Catch |
| Парткод: | 660-05105-006 |
| Деталь: | FIXED PLATE, ROTARY CATCH |
| Парткод: | 021-11140-106 |
| Деталь: | FRONT COVER |
| Парткод: | 059-34024-003 |
| Деталь: | INK REPLACE INSTRUCTION STICKER , PIC |
| Парткод: | 059-17003-000 |
| Деталь: | PANEL COVER, BOTTOM |
| Парткод: | 059-37001-004 |
| Деталь: | SEAL, M.-M. UNIT RELEASE, PIC. |
| Парткод: | 059-28002-006 |
| Деталь: | N/A |
| Парткод: | 059-28004-009 |
| Деталь: | N/A |
| Парткод: | 059-34044-004 |
| Деталь: | N/A |
| Парткод: | 059-34039-000 |
| Деталь: | HINGE LOWER, FRONT DOOR |
| Парткод: | 059-34040-009 |
| Деталь: | SIDE COVER, PAPER EJECTION SIDE |
| Парткод: | 059-34042-001 |
| Деталь: | SCANNER COVER, P.-RCV. SIDE |
| Парткод: | 059-34034-009 |
| Деталь: | SIDE COVER, PAPER FEEDING SIDE |
| Парткод: | 059-34043-008 |
| Деталь: | SCANNERCOVER, PAPER FEEDING SIDE |
| Парткод: | 059-34030-003 |
| Деталь: | REAR SIDE COVER |
| Парткод: | 059-34046-007 |
| Деталь: | Scanner cover, rear |
| Парткод: | 059-34031-000 |
| Деталь: | REAR COVER, L/LL |
| Парткод: | 059-34045-007 |
| Деталь: | BRACKET LOWER, REAR COVER |
| Парткод: | 023-34024-108 |
| Деталь: | BRACKET LEFT, SCANNER REAR COVER |
| Парткод: | 023-34025-104 |
| Деталь: | SIDE COVER, PAPER EJECTION SIDE |
| Парткод: | 059-34032-006 |
| Деталь: | HINGE BASE UPPER, FRONT DOOR |
| Парткод: | 059-34029-005 |
| Деталь: | SEAL, MAGNET ADJUSTER |
| Парткод: | 023-34054-007 |
| Деталь: | STEPPED SCREW, F5.3X3.5, M4X6 |
| Парткод: | 635-10014-008 |
| Деталь: | HINGE BASE LOWER, FRONT DOOR |
| Парткод: | 059-34025-000 |
| Деталь: | FIXED PLATE , M LOADING COVER |
| Парткод: | 023-34083-007 |
| Деталь: | SHEET, FRONT DOOR SET SENSOR |
| Парткод: | 059-34051-000 |
| Деталь: | SEAL, M.-M. UNIT RELEASE, ENG. |
| Парткод: | 059-28003-002 |
| Деталь: | MAGNET CATCH |
| Парткод: | 021-11220-100 |
| Деталь: | EMBLEM, SF9450 |
| Парткод: | 059-34003-006 |
| Деталь: | EMBLEM, SF9350 |
| Парткод: | 059-34004-002 |
| Деталь: | EMBLEM, SF9250 |
| Парткод: | 059-34005-009 |
| Деталь: | N/A |
| Парткод: | 059-34013-001 |
| Деталь: | N/A |
| Парткод: | 059-34014-008 |
| Деталь: | EMBLEM, SF5250 |
| Парткод: | 059-34015-004 |
| Деталь: | N/A |
| Парткод: | 059-34016-000 |
| Деталь: | N/A |
| Парткод: | 059-34017-104 |
| Деталь: | xxx |
| Парткод: | 059-34018-100 |
| Деталь: | EMBLEM, SF5230 |
| Парткод: | 059-34019-107 |
| Деталь: | N/A |
| Парткод: | 059-34020-105 |
| Деталь: | N/A |
| Парткод: | 059-34021-101 |
| Деталь: | N/A |
| Парткод: | 059-34056-002 |
| Деталь: | N/A |
| Парткод: | 059-34057-009 |
| Деталь: | N/A |
| Парткод: | 059-34058-005 |
| Деталь: | N/A |
| Парткод: | 059-34059-109 |
| Деталь: | N/A |
| Парткод: | 059-34060-107 |
| Деталь: | N/A |
| Парткод: | 059-34061-103 |
| Деталь: | N/A |
| Парткод: | 059-34062-100 |
| Деталь: | N/A |
| Парткод: | 059-34064-005 |
| Деталь: | N/A |
| Парткод: | 059-34065-109 |
| Деталь: | N/A |
| Парткод: | 059-34066-105 |
| Деталь: | N/A |
| Парткод: | 059-75091-009 |
| Деталь: | N/A |
| Парткод: | 059-75089-004 |
| Деталь: | N/A |
| Парткод: | 059-75092-005 |
| Деталь: | N/A |
| Парткод: | 059-75090-002 |
| Деталь: | N/A |
| Парткод: | 059-75093-001 |
| Деталь: | WRITE MOTOR ASSY L |
| Парткод: | 023-75145-106 |
| Деталь: | WRITE MOTOR ASSY LL |
| Парткод: | 023-75146-102 |
| Деталь: | BELT, 256-2GT-4 |
| Парткод: | 620-80001-008 |
| Деталь: | BRACKET, WRITE PULSE MOTOR |
| Парткод: | 023-28195-103 |
| Деталь: | MOTOR, PM42L-048-ZVS6 |
| Парткод: | 490-33015-100 |
| Деталь: | GEAR PULLEY, M0.5X130+17-2 |
| Парткод: | 613-10002-002 |
| Деталь: | PULLEY ASSY, P40-2GT-5 |
| Парткод: | 611-90010-006 |
| Деталь: | BRACKET, PCB, M.-MAKING |
| Парткод: | 023-28016-004 |
| Деталь: | BRACKET BOTTOM, MASTER MAKING PCB |
| Парткод: | 023-28401-005 |
| Деталь: | MASTER MAKING PCB |
| Парткод: | 059-50007-003 |
| Деталь: | WIRE HARNESS, M-M UNIT STAY PLATE |
| Парткод: | 059-53019-002 |
| Деталь: | FRONT COVER, M.-M. UNIT |
| Парткод: | 059-28016-007 |
| Деталь: | SEAL, SETTING MASTER, PIC. |
| Парткод: | 059-28030-000 |
| Деталь: | SEAL, MASTER MAKING UNIT COVER |
| Парткод: | 059-28029-001 |
| Деталь: | BRACKET FRONT UPPER, RAIL, M.-M. |
| Парткод: | 023-28001-007 |
| Деталь: | PRE-PRESSURE SPRING, RIGHT, DRUM |
| Парткод: | 023-17139-104 |
| Деталь: | BRACKET REAR UPPER, RAIL, M.-M. |
| Парткод: | 023-28002-003 |
| Деталь: | xxx |
| Парткод: | 023-17140-102 |
| Деталь: | N/A |
| Парткод: | 054-28007-001 |
| Деталь: | BRACKET FRONT BOTTOM, RAIL, M.-M. |
| Парткод: | 023-28084-000 |
| Деталь: | BRACKET REAR BOTTOM, RAIL, M.-M. |
| Парткод: | 023-28012-009 |
| Деталь: | SHAFT HOLDER, LEFT |
| Парткод: | 046-28003-004 |
| Деталь: | WIRE HARNESS, PAPER EJECTION REAR |
| Парткод: | 059-53004-005 |
| Деталь: | POSITIONING PIN, REAR, M.-M |
| Парткод: | 023-28086-002 |
| Деталь: | STEPPED SCREW, F5X5, M3X3 |
| Парткод: | 635-10004-002 |
| Деталь: | BRACKET, DRAWER CONNECTOR, M.-M. |
| Парткод: | 023-28085-006 |
| Деталь: | WIRE HARNESS, TPH DRAWER CONNECTOR H |
| Парткод: | 059-53014-000 |
| Деталь: | GUIDE LOWER, FLEXIBLE WIRE, M.-M |
| Парткод: | 059-28018-000 |
| Деталь: | GUIDE UPPER, FLEXIBLE WIRE, M.-M |
| Парткод: | 059-28017-003 |
| Деталь: | GUIDE BRACKET, WIRE HARNESS, M.-M. |
| Парткод: | 023-28010-006 |
| Деталь: | HOLDING PLATE, WIRE HARNESS, M.-M. |
| Парткод: | 023-28353-000 |
| Деталь: | FLEXIBLE WIRE, M.-M |
| Парткод: | 059-53016-003 |
| Деталь: | GUIDE ROLLER, WIRE HARNESS, M.-M. |
| Парткод: | 023-28200-000 |
| Деталь: | BRACKET, SLIDE LOCK, M.-M. |
| Парткод: | 023-28003-000 |
| Деталь: | SHAFT, STOPPER, M.-M |
| Парткод: | 023-28122-203 |
| Деталь: | HOOK STOPPER, HANDLE, M.-M. |
| Парткод: | 023-28121-002 |
| Деталь: | SPRING, STOPPER, M.-M |
| Парткод: | 023-28339-008 |
| Деталь: | xxx |
| Парткод: | 490-50006-106 |
| Деталь: | BUTTON SW ASSY |
| Парткод: | 059-53001-103 |
| Деталь: | COVER, M.-M. UNIT SAFETY SW |
| Парткод: | 023-28119-008 |
| Деталь: | SET PLATE, INTERLOCK SW, REAR |
| Парткод: | 048-28006-008 |
| Деталь: | SPRING, SAFETY SW/DRUM & MM |
| Парткод: | 023-28403-105 |
| Деталь: | BRACKET, M.-M. UNIT SET SW |
| Парткод: | 023-28404-004 |
| Деталь: | SAFETY SW ASSY, M-RMV UNIT |
| Парткод: | 023-53025-000 |
| Деталь: | SENSOR, LG248D2 |
| Парткод: | 444-30019-004 |
| Деталь: | WIRE HARNESS, LOWER F |
| Парткод: | 059-53015-007 |
| Деталь: | N/A |
| Парткод: | 054-17015-002 |
| Деталь: | N/A |
| Парткод: | 059-75094-008 |
| Деталь: | N/A |
| Парткод: | 059-75095-004 |
| Деталь: | HOUSING, M.-REV. |
| Парткод: | 046-24021-105 |
| Деталь: | BRACKET, HOUSING, M.-REV. |
| Парткод: | 046-24128-007 |
| Деталь: | HOOK, M.-RMV ROLLER |
| Парткод: | 046-24062-006 |
| Деталь: | SHAFT, PULLY, M.-RMV. |
| Парткод: | 046-24007-005 |
| Деталь: | HOLDING PLATE, PULLEY, M.-RMV. |
| Парткод: | 023-24129-009 |
| Деталь: | PLATE, M.-RMV. PULLEY |
| Парткод: | 023-24062-109 |
| Деталь: | PULLEY, M-RMV |
| Парткод: | 023-24061-102 |
| Деталь: | SHAFT, PULLEY, M-RMV |
| Парткод: | 023-24063-300 |
| Деталь: | SPRING, ROLLER B1 |
| Парткод: | 024-24067-000 |
| Деталь: | O RING, S42-2.0 |
| Парткод: | 640-60001-004 |
| Деталь: | SHAFT, ROLLER, M.-RMV. |
| Парткод: | 046-24057-207 |
| Деталь: | SPRING CATCH |
| Парткод: | 030-19131-008 |
| Деталь: | SPRING, ROLLER |
| Парткод: | 024-25057-009 |
| Деталь: | PULLY SHAFT, M.-RMV. |
| Парткод: | 046-24025-003 |
| Деталь: | METAL, F6X10/9X4, 12X1.5 |
| Парткод: | 651-00017-002 |
| Деталь: | GEAR, M1X1.25X16X7 |
| Парткод: | 612-10058-000 |
| Деталь: | BRACKET, MASTER LOADING SENSOR |
| Парткод: | 046-24088-005 |
| Деталь: | MASTER LOADING SENSOR/SENSOR/KH0726 |
| Парткод: | 451-40010-000 |
| Деталь: | BRACKET, M.-RMV .SENSOR |
| Парткод: | 046-24056-006 |
| Деталь: | SENSOR, OS-RS04Y01 |
| Парткод: | 444-41003-100 |
| Деталь: | xxx |
| Парткод: | 046-24011-002 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | LOCK RING 4 |
| Парткод: | 023-17197-007 |
| Деталь: | N/A |
| Парткод: | 059-53010-005 |
| Деталь: | SPRING, ROLLER HOOK |
| Парткод: | 024-25058-102 |
| Деталь: | N/A |
| Парткод: | 059-75099-000 |
| Деталь: | N/A |
| Парткод: | 059-12006-001 |
| Деталь: | L.O. SHEET |
| Парткод: | 020-11520-106 |
| Деталь: | SEAL, CLOSING TRAY INSTRUCTION, P.- |
| Парткод: | 023-12150-002 |
| Деталь: | BRACKET, CATCH |
| Парткод: | 023-12126-004 |
| Деталь: | N/A |
| Парткод: | 060-50037-000 |
| Деталь: | WIRE HARNESS II, P.-F.-T |
| Парткод: | 046-12700-007 |
| Деталь: | POTENTIOMETER, P.-F.-T |
| Парткод: | 023-12605-204 |
| Деталь: | SHAFT, POTENTIOMETER GEAR |
| Парткод: | 023-12241-105 |
| Деталь: | GEAR,M1X50X6 |
| Парткод: | 612-10023-002 |
| Деталь: | SENSOR , PS124TD1 |
| Парткод: | 444-33013-007 |
| Деталь: | SIDE GUIDE F, P.-F.-T |
| Парткод: | 023-12139-300 |
| Деталь: | SIDE GUIDE R, P.-F.-T |
| Парткод: | 023-12140-309 |
| Деталь: | SEAL, SETTING INSTRUCTION, P.-F.-T |
| Парткод: | 023-12147-001 |
| Деталь: | N/A |
| Парткод: | 059-12008-004 |
| Деталь: | LINK PLATE A, P.-F.-T. |
| Парткод: | 023-12109-002 |
| Деталь: | LINK PLATE B,P.-F.-T. |
| Парткод: | 023-12128-104 |
| Деталь: | SLIDE RACK II, P.-F.-T |
| Парткод: | 046-12101-006 |
| Деталь: | GEAR,SLIDE RACK,P.-F.-T. |
| Парткод: | 011-11514-000 |
| Деталь: | GUIDE PLATE, SLIDE RACK |
| Парткод: | 023-12129-003 |
| Деталь: | FLEXIBLE WIRE COVER, P.-F.-T. |
| Парткод: | 059-12010-009 |
| Деталь: | BOTTOM FRAME, P.-F.-T. |
| Парткод: | 023-12102-105 |
| Деталь: | SHAFT, P.-F. TRAY |
| Парткод: | 023-12132-004 |
| Деталь: | ADJ. NUT, P.-F.-T. |
| Парткод: | 023-12123-102 |
| Деталь: | xxx |
| Парткод: | 059-12009-000 |
| Деталь: | BRACKET, P.-F.-T. |
| Парткод: | 023-12121-304 |
| Деталь: | BRACKET , HINGE COVER |
| Парткод: | 023-12155-305 |
| Деталь: | ONE-WAY HINGE, OWHF6-1NRS |
| Парткод: | 610-10009-005 |
| Деталь: | GEAR,M1X20X7 |
| Парткод: | 612-10036-007 |
| Деталь: | HINGE SHAFT, P.-F.-T |
| Парткод: | 023-12254-100 |
| Деталь: | ADJ. SEAL LOWER, P.-F.-T |
| Парткод: | 059-12002-006 |
| Деталь: | STEPPED SCREW , F6X1.8 , M3X4 |
| Парткод: | 635-00001-005 |
| Деталь: | Connector Cover |
| Парткод: | 059-12007-008 |
| Деталь: | MAGNET CATCH , SM50-P |
| Парткод: | 660-00002-004 |
| Деталь: | JUNCTION WIRE HARNESS ,SAFETY SW,LL |
| Парткод: | 046-12708-105 |
| Деталь: | N/A |
| Парткод: | 059-53022-003 |
| Деталь: | HOLDER, FLEXIBLE WIRE, P.-F.-T. |
| Парткод: | 023-12138-002 |
| Деталь: | ADJ. SEAL UPPER, P.-F.-T |
| Парткод: | 059-12001-000 |
| Деталь: | xxx |
| Парткод: | 638-90006-100 |
| Деталь: | MODULE ASSY |
| Парткод: | 059-75006-001 |
| Деталь: | LED UNIT ASSY |
| Парткод: | 059-75007-008 |
| Деталь: | FRAME(UP) ASSY |
| Парткод: | 059-75008-004 |
| Деталь: | MOTOR PLATE ASSY |
| Парткод: | 059-75009-000 |
| Деталь: | SNS ASSY |
| Парткод: | 059-75010-009 |
| Деталь: | FFC CABLE ASSY |
| Парткод: | 059-75011-005 |
| Деталь: | LOCK LEVER |
| Парткод: | 059-75014-004 |
| Деталь: | SPONGE2MM |
| Парткод: | 059-75013-008 |
| Деталь: | SPONGE3MM |
| Парткод: | 059-75015-000 |
| Деталь: | SHEET CD SCALE |
| Парткод: | 059-75016-007 |
| Деталь: | FRAME HINGE R |
| Парткод: | 059-75017-003 |
| Деталь: | FRAME HINGE L |
| Парткод: | 059-75018-000 |
| Деталь: | ADF SPRING |
| Парткод: | 059-75019-006 |
| Деталь: | 102T BELT |
| Парткод: | 059-75020-004 |
| Деталь: | WIRE |
| Парткод: | 059-75021-000 |
| Деталь: | LG248NL1 |
| Парткод: | 059-75022-007 |
| Деталь: | PS182EL1 |
| Парткод: | 059-75023-003 |
| Деталь: | BS SNS CABLE-H |
| Парткод: | 059-75024-000 |
| Деталь: | N/A |
| Парткод: | 054-17015-002 |
| Деталь: | DRUM SUPPORT LEFT, RAIL |
| Парткод: | 023-17062-101 |
| Деталь: | DRUM SUPPORT RIGHT, RAIL |
| Парткод: | 023-17061-105 |
| Деталь: | PRE-PRESSURE SPRING, LEFT, DRUM |
| Парткод: | 023-17140-102 |
| Деталь: | PRE-PRESSURE SPRING, RIGHT, DRUM |
| Парткод: | 023-17139-104 |
| Деталь: | BRIDGE, DRUM RAIL |
| Парткод: | 023-17060-206 |
| Деталь: | RIGHT GUIDE, DRUM FRAME FRONT |
| Парткод: | 023-17203-201 |
| Деталь: | LEFT GUIDE, DRUM FRAME FRONT |
| Парткод: | 023-17204-208 |
| Деталь: | SEAL, DRUM SET POSITION |
| Парткод: | 023-17302-005 |
| Деталь: | DRUM LOCK ASSY |
| Парткод: | 023-75134-104 |
| Деталь: | DRUM LOCK BASE |
| Парткод: | 023-17087-201 |
| Деталь: | SOLENOID, TDS-10A-1056 |
| Парткод: | 490-50006-106 |
| Деталь: | SHAFT, DRUM SOLENOID LEVER |
| Парткод: | 023-17132-100 |
| Деталь: | DRUM SOLENOID LEVER |
| Парткод: | 023-17131-200 |
| Деталь: | SPRING, DRUM LOCK |
| Парткод: | 023-17082-005 |
| Деталь: | SPRING, SAFETY SW/DRUM & MM |
| Парткод: | 023-28403-105 |
| Деталь: | BRACKET, M.-M. UNIT SET SW |
| Парткод: | 023-28404-004 |
| Деталь: | DRUM SAFETY SW |
| Парткод: | 023-53024-100 |
| Деталь: | BRACKET, DRUM LOCK SENSOR |
| Парткод: | 023-17164-109 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | BRACKET, DRAWER CONNECTOR, DRUM |
| Парткод: | 059-17025-004 |
| Деталь: | WIRE HARNESS, DRUM DRAWER H |
| Парткод: | 059-53025-100 |
| Деталь: | BASE BRACKET, B POSITION LOCK |
| Парткод: | 046-17004-009 |
| Деталь: | GUIDE, B POSITION LOCK REREASE |
| Парткод: | 046-17003-002 |
| Деталь: | xxx |
| Парткод: | 030-16108-005 |
| Деталь: | SHAFT HOLDER, LEFT |
| Парткод: | 030-16109-001 |
| Деталь: | WIRE HARNESS, LOWER F |
| Парткод: | 059-53015-007 |
| Деталь: | GUIDE , FRONT COVER |
| Парткод: | 023-17400-007 |
| Деталь: | DRUM BODY L,A3,SU |
| Парткод: | 023-75061-204 |
| Деталь: | DRUM BODY L,LEDGER,SU |
| Парткод: | 023-75063-207 |
| Деталь: | DRUM BODY L,A4,SU |
| Парткод: | 023-75062-200 |
| Деталь: | DRUM BODY,B4ML |
| Парткод: | 023-75067-202 |
| Деталь: | DRUM BODY,A4R |
| Парткод: | 023-75068-004 |
| Деталь: | N/A |
| Парткод: | 059-17024-008 |
| Деталь: | light Absorber Strip(328X20) |
| Парткод: | 023-17004-306 |
| Деталь: | HANGER PLATE, SCREEN |
| Парткод: | 023-17003-008 |
| Деталь: | INK BLOCKING SHEET , A3 |
| Парткод: | 023-17345-006 |
| Деталь: | INK BLOCKING SHEET,B4 |
| Парткод: | 023-17189-101 |
| Деталь: | INK BLOCKING SHEET, A4 |
| Парткод: | 023-17190-100 |
| Деталь: | SEAL TAPE,A3 |
| Парткод: | 023-17256-003 |
| Деталь: | SEAL TAPE,B4 |
| Парткод: | 023-17257-000 |
| Деталь: | SEAL TAPE,A4 |
| Парткод: | 023-17258-006 |
| Деталь: | DRUM SEAL |
| Парткод: | 023-17007-003 |
| Деталь: | Flange Front |
| Парткод: | 023-17012-104 |
| Деталь: | N/A |
| Парткод: | 046-17325-000 |
| Деталь: | BALANCER,FRONT B |
| Парткод: | 024-17131-003 |
| Деталь: | None |
| Парткод: | 023-17149-002 |
| Деталь: | B Position Marking Sticker |
| Парткод: | 023-17307-007 |
| Деталь: | FLANGE GEAR, DRUM |
| Парткод: | 023-17009-006 |
| Деталь: | Drum Flange Rear |
| Парткод: | 023-17006-201 |
| Деталь: | BALANCER,REAR A |
| Парткод: | 024-17132-000 |
| Деталь: | BALANCER,REAR B |
| Парткод: | 024-17133-006 |
| Деталь: | METAL STOPPER, DRUM |
| Парткод: | 023-17263-000 |
| Деталь: | Drum Shaft Joint |
| Парткод: | 023-17008-107 |
| Деталь: | BOSS, A POSITION COMPENSATION |
| Парткод: | 023-17010-004 |
| Деталь: | CLAMP PLATE ASSY |
| Парткод: | 023-75112-208 |
| Деталь: | CLAMP PLATE BASE |
| Парткод: | 023-17067-308 |
| Деталь: | CLAMP MAGNET |
| Парткод: | 023-17181-100 |
| Деталь: | FRICTION SHEET |
| Парткод: | 023-17180-007 |
| Деталь: | SPRING, CLAMP PLATE BASE |
| Парткод: | 023-17251-001 |
| Деталь: | CLAMP PLATE |
| Парткод: | 023-17068-207 |
| Деталь: | RELEASE LEVER, CLAMP PLATE |
| Парткод: | 023-17191-203 |
| Деталь: | COLLAR D12, CLAMP |
| Парткод: | 023-17069-009 |
| Деталь: | SPRING, CLAMP PLATE CLOSE |
| Парткод: | 023-17275-008 |
| Деталь: | PROJECTION PLATE |
| Парткод: | 023-17071-208 |
| Деталь: | SPRING, PROJECTION PLATE |
| Парткод: | 023-17073-103 |
| Деталь: | None |
| Парткод: | 023-17187-001 |
| Деталь: | STEPPED SCREW,F6X5,M3X5 |
| Парткод: | 635-10008-105 |
| Деталь: | SHEET,CLUMP PLATE BASE |
| Парткод: | 023-17342-007 |
| Деталь: | Light Absorber Strip (65X18) |
| Парткод: | 023-17344-204 |
| Деталь: | TAPE, DRUM BODY JOINT 335X30 |
| Парткод: | 023-17424-003 |
| Деталь: | BALANCER,REAR C |
| Парткод: | 024-17134-070 |
| Деталь: | TPH ASSY II, TA3 |
| Парткод: | 046-75002-008 |
| Деталь: | TPH ASSY II, TB4 |
| Парткод: | 046-75003-004 |
| Деталь: | TPH-ASSY2H, SU |
| Парткод: | 047-75046-006 |
| Деталь: | HOLDING BRACKET, TA3 |
| Парткод: | 046-28005-007 |
| Деталь: | HOLDING BRACKET, TB4 |
| Парткод: | 046-28019-008 |
| Деталь: | TPH PRESSURE ASSIST PLATE, A3 |
| Парткод: | 023-28413-003 |
| Деталь: | TPH PRESSURE ASSIST PLATE, B4 |
| Парткод: | 023-28387-100 |
| Деталь: | PROTECTION PLATE, TPH CONNECTOR TA3 |
| Парткод: | 023-28315-206 |
| Деталь: | TPH 303R11/THERMAL PRINT HEAD |
| Парткод: | 444-80001-602 |
| Деталь: | TPH260R39/THERMAL PRINT HEAD |
| Парткод: | 444-80002-609 |
| Деталь: | TPH303R16 |
| Парткод: | 444-80007-309 |
| Деталь: | PLATE T-REAR, TPH |
| Парткод: | 023-28021-202 |
| Деталь: | PLATE T-FRONT, TPH |
| Парткод: | 023-28022-209 |
| Деталь: | BRACKET, TPH BRUSH, TA3 |
| Парткод: | 023-28175-200 |
| Деталь: | BRACKET, TPH BRUSH, TB4 |
| Парткод: | 023-28298-107 |
| Деталь: | DE-ELECTRICITY BRUSH, TPH A3 |
| Парткод: | 023-28411-000 |
| Деталь: | DE-ELECTRICITY BRUSH, TPH B4 |
| Парткод: | 023-28414-000 |
| Деталь: | HOLDING ROLLER, TA3 |
| Парткод: | 023-28024-007 |
| Деталь: | HOLDING ROLLER, TB4 |
| Парткод: | 023-28299-103 |
| Деталь: | TPH BOSS |
| Парткод: | 023-28412-309 |
| Деталь: | STEPPED SCREW, F6X7.2, M3X4 |
| Парткод: | 635-10005-106 |
| Деталь: | METAL, F8X10X3, 11.2X0.6 |
| Парткод: | 607-10005-004 |
| Деталь: | GROUND WIRE, U3-55-R3 |
| Парткод: | 488-90030-109 |
| Деталь: | N/A |
| Парткод: | 059-75111-000 |
| Деталь: | N/A |
| Парткод: | 059-75109-005 |
| Деталь: | N/A |
| Парткод: | 060-21056-101 |
| Деталь: | Fence Cushion |
| Парткод: | 018-33151-408 |
| Деталь: | SHAFT, FENCE |
| Парткод: | 023-21634-209 |
| Деталь: | SLIDE BASE, P.RCV.-T. |
| Парткод: | 046-21024-006 |
| Деталь: | SLIDE PLATE(UPPER), P.-RCV.-T. |
| Парткод: | 023-21637-003 |
| Деталь: | PLATE SPRING, P.-RCV.-T |
| Парткод: | 023-21638-107 |
| Деталь: | SLIDE PLATE(UPPER), P.-RCV.-T. |
| Парткод: | 023-21636-104 |
| Деталь: | N/A |
| Парткод: | 060-21060-001 |
| Деталь: | N/A |
| Парткод: | 060-21055-008 |
| Деталь: | N/A |
| Парткод: | 060-21054-001 |
| Деталь: | SLIDE RAIL, PAPER GUIDE, P.-RCV.-T. |
| Парткод: | 023-21639-006 |
| Деталь: | N/A |
| Парткод: | 059-21002-000 |
| Деталь: | SIDE FRAME R, P.-RCV.-T. |
| Парткод: | 023-21603-508 |
| Деталь: | SIDE FRAME F, P.-RCV.-T. |
| Парткод: | 023-21602-501 |
| Деталь: | GROUND PLATE, SLIDE RAIL, P.RCV.-T. |
| Парткод: | 023-21633-105 |
| Деталь: | PAPER RECEIVING TRAY |
| Парткод: | 059-21007-002 |
| Деталь: | BRACKET, MAGNET CATCH, P.-RCV.-T. |
| Парткод: | 023-21643-003 |
| Деталь: | MAGNET CATCH , SM50-P |
| Парткод: | 660-00002-004 |
| Деталь: | SEAL, P.-PCV.-T:FOLDING PIC |
| Парткод: | 023-21802-004 |
| Деталь: | N/A |
| Парткод: | 060-21059-003 |
| Деталь: | N/A |
| Парткод: | 060-21058-007 |
| Деталь: | N/A |
| Парткод: | 060-21057-000 |
| Деталь: | xxx |
| Парткод: | 060-21057-000 |
| Деталь: | BALANCER, FLAP, P.-RCV.-T. |
| Парткод: | 023-21613-007 |
| Деталь: | Paper Guiding Arm F |
| Парткод: | 023-21650-000 |
| Деталь: | Paper Guiding Arm R |
| Парткод: | 023-21651-006 |
| Деталь: | SHAFT , PAPER GUIDING ARM |
| Парткод: | 023-21652-002 |
| Деталь: | SPRING , PAPER GUIDING ARM |
| Парткод: | 023-21653-009 |
| Деталь: | N/A |
| Парткод: | 059-21012-006 |
| Деталь: | N/A |
| Парткод: | 059-21003-007 |
| Деталь: | Drum Frame Front |
| Парткод: | 059-17016-005 |
| Деталь: | Slide Shaft |
| Парткод: | 023-17045-100 |
| Деталь: | BRACKET, DRUM LEVER |
| Парткод: | 023-17207-002 |
| Деталь: | Drum Lever |
| Парткод: | 023-17095-000 |
| Деталь: | Drum Handle Cover |
| Парткод: | 059-17023-001 |
| Деталь: | BRACKET, DRUM LOCK |
| Парткод: | 059-17021-009 |
| Деталь: | SHAFT, DRUM LOCK PLATE |
| Парткод: | 023-17138-205 |
| Деталь: | LINK PLATE, DRUM LOCK |
| Парткод: | 023-17161-002 |
| Деталь: | LINK SHAFT, DRUM LOCK |
| Парткод: | 023-17162-106 |
| Деталь: | PLATE, DRUM LOCK |
| Парткод: | 023-17136-008 |
| Деталь: | STEPPED SCREW,DIA.5X2,M3X3 |
| Парткод: | 635-17523-102 |
| Деталь: | SPRING, DRUM LOCK LINK |
| Парткод: | 023-17177-103 |
| Деталь: | BRACKET, DRUM-PCB |
| Парткод: | 023-17175-003 |
| Деталь: | Drum PCB II |
| Парткод: | 046-17178-007 |
| Деталь: | WIRE HARNESS, DRUM DRAWER U |
| Парткод: | 059-53024-103 |
| Деталь: | SPRING , DRUM DRAWER |
| Парткод: | 042-17213-008 |
| Деталь: | STEPPED SCREW , F3.5X20.5 , M3X7 |
| Парткод: | 635-10016-000 |
| Деталь: | STAY, DRUM FRAME FRONT |
| Парткод: | 023-17192-005 |
| Деталь: | B Pos. Lock Lever |
| Парткод: | 023-17159-504 |
| Деталь: | COVER, B POSITION LOCK LEVER |
| Парткод: | 023-17244-005 |
| Деталь: | B Position Lock Chip |
| Парткод: | 023-17273-005 |
| Деталь: | LOCK SPRING, B POS. |
| Парткод: | 023-17054-001 |
| Деталь: | SIDE FRAME, DRUM |
| Парткод: | 023-17046-106 |
| Деталь: | Drum Guide |
| Парткод: | 059-17026-000 |
| Деталь: | None |
| Парткод: | 023-17044-200 |
| Деталь: | COVER, REAR HANDLE |
| Парткод: | 059-17020-002 |
| Деталь: | LINER POM, REAR FRAME, DRUM |
| Парткод: | 023-17094-003 |
| Деталь: | COVER, FRONT FRAME, DRUM |
| Парткод: | 059-17022-005 |
| Деталь: | SEAL, DRUM SET POSITION |
| Парткод: | 023-17302-005 |
| Деталь: | SEAL, SETTING CARTRIDGE |
| Парткод: | 023-17301-009 |
| Деталь: | B Position Marking Sticker |
| Парткод: | 023-17307-007 |
| Деталь: | SEAL, INK COLOR |
| Парткод: | 023-17306-205 |
| Деталь: | SEAL, INK, BLACK |
| Парткод: | 023-17320-003 |
| Деталь: | SEAL, DRUM TYPE |
| Парткод: | 059-17029-107 |
| Деталь: | ADJ. PLATE , DRUM LOCK |
| Парткод: | 023-17403-006 |
| Деталь: | STEPPED SCREW,F5X2,M3X3:SG |
| Парткод: | 635-10011-106 |
| Деталь: | SLIDE SHAFT L |
| Парткод: | 059-17019-004 |
| Деталь: | COVER, P-FEED |
| Парткод: | 059-12014-004 |
| Деталь: | STICKER, P-FEED PRESSURE SETTING |
| Парткод: | 060-12127-004 |
| Деталь: | SEAL, P.-F.-T. DOWN |
| Парткод: | 030-04034-006 |
| Деталь: | Upper Guard |
| Парткод: | 023-12319-007 |
| Деталь: | STEPPED SCREW ,F8X2.3 , M4X4.4 |
| Парткод: | 635-00004-004 |
| Деталь: | E SWITCH PLATE |
| Парткод: | 046-12306-007 |
| Деталь: | SPRING, ELEVATOR SAFETY SW, UPPER |
| Парткод: | 023-12344-001 |
| Деталь: | CASE,SW |
| Парткод: | 046-12304-004 |
| Деталь: | Elevator Safety SW |
| Парткод: | 023-53023-104 |
| Деталь: | FRAME BRACKET, PICK-UP |
| Парткод: | 023-12333-204 |
| Деталь: | SHAFT, PICK-UP ROLLER |
| Парткод: | 023-12329-002 |
| Деталь: | GEAR,M0.8X33X7.4 |
| Парткод: | 612-10021-107 |
| Деталь: | METAL,F10X15/14X6,18X2 |
| Парткод: | 607-16001-000 |
| Деталь: | SUPPORT, PICK-UP ROLLER SHAFT |
| Парткод: | 023-12328-103 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | 021-14301-208 |
| Деталь: | RUBBER ROLLER,PICKUP |
| Парткод: | 035-14303-001 |
| Деталь: | CORE,PICKUP ROLLER |
| Парткод: | 021-14302-204 |
| Деталь: | Lock Ring |
| Парткод: | 019-11812-106 |
| Деталь: | SCRAPER SHAFT, PICKUP |
| Парткод: | 023-12330-000 |
| Деталь: | GEAR,M0.8X34X8.5 |
| Парткод: | 612-11300-107 |
| Деталь: | ACTUATOR, UPPER LIMIT, STD, P.-F.-T |
| Парткод: | 023-12334-006 |
| Деталь: | ACTUATOR, UPPER LIMIT, CARD, P.-F.- |
| Парткод: | 023-12308-005 |
| Деталь: | xxx |
| Парткод: | 059-12013-008 |
| Деталь: | xxx |
| Парткод: | 059-12012-001 |
| Деталь: | xxx |
| Парткод: | 020-11811-208 |
| Деталь: | P.-F.Pressure Adj.Lever |
| Парткод: | 059-12011-005 |
| Деталь: | SPRING, PF PRESSURE ADJ. LEVER |
| Парткод: | 023-12313-106 |
| Деталь: | SUPPORT PLATE, UPPER LIMIT ADJUST |
| Парткод: | 046-12302-001 |
| Деталь: | BRACKET B, UPPER LIMIT SENSOR |
| Парткод: | 046-12301-005 |
| Деталь: | BASE, UPPER LIMIT ADJ. SCREW |
| Парткод: | 030-14347-002 |
| Деталь: | BRACKET A, UPPER LIMIT SENSOR |
| Парткод: | 023-12314-005 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | BRACKET,UPPER LIMIT SENSOR |
| Парткод: | 023-12325-007 |
| Деталь: | xxx |
| Парткод: | 059-53031-002 |
| Деталь: | JUNCTION WIRE HARNESS ,SAFETY SW,LL |
| Парткод: | 046-12708-105 |
| Деталь: | BRACKET, CLUTCH, PICK-UP ROLLER |
| Парткод: | 059-15001-000 |
| Деталь: | METALF8X13/12X5,16X2 |
| Парткод: | 651-00018-009 |
| Деталь: | CLUTCH, MC10-36 |
| Парткод: | 451-20018-004 |
| Деталь: | METAL,F8X12/10.8X4.8,16X2 |
| Парткод: | 651-00020-003 |
| Деталь: | WIRE HARNESS, PAPER FEED REAR |
| Парткод: | 059-53005-001 |
| Деталь: | P-U , SHAFT ASSY |
| Парткод: | 023-75154-105 |
| Деталь: | Paper Guide Roller |
| Парткод: | 011-11522-002 |
| Деталь: | STOPPER,PAPER GUIDE ROLLER |
| Парткод: | 000-06123-007 |
| Деталь: | xxx |
| Парткод: | 023-12346-004 |
| Деталь: | COVER,P.U.GEAR,LOWER |
| Парткод: | 023-12347-000 |
| Деталь: | PAPER UPSIDE CHECK LEVER |
| Парткод: | 023-12331-104 |
| Деталь: | BEARING,F-606ZZ1 |
| Парткод: | 600-06172-205 |
| Деталь: | STEPPED SCREW,DIA.5X2,M3X3 |
| Парткод: | 635-17523-102 |
| Деталь: | STEPPED SCERW,3X7 |
| Парткод: | 635-11307-203 |
| Деталь: | COVER,FIRST ACTUATOR GEAR |
| Парткод: | 023-15156-001 |
| Деталь: | SPRING , SW |
| Парткод: | 046-12305-000 |
| Деталь: | xxx |
| Парткод: | 060-12133-004 |
| Деталь: | N/A |
| Парткод: | 059-75117-008 |
| Деталь: | COVER, DISPOSAL BOX |
| Парткод: | 046-24036-005 |
| Деталь: | N/A |
| Парткод: | 059-24001-008 |
| Деталь: | N/A |
| Парткод: | 059-24002-001 |
| Деталь: | N/A |
| Парткод: | 059-24003-008 |
| Деталь: | HANDLE SPRING, DISPOSAL BOX |
| Парткод: | 023-24148-100 |
| Деталь: | SPRING, BOX COVER |
| Парткод: | 024-24141-200 |
| Деталь: | SEAL, DISPOSAL INSTRUCTION A |
| Парткод: | 046-24143-103 |
| Деталь: | SEAL, DISPOSAL INSTRUCTION B |
| Парткод: | 046-24144-100 |
| Деталь: | DETECTION SHEET, BOX SET |
| Парткод: | 046-24145-009 |
| Деталь: | BRACKET, M.-RMV. |
| Парткод: | 023-24132-000 |
| Деталь: | COVER, M.-RMV. |
| Парткод: | 059-24004-004 |
| Деталь: | N/A |
| Парткод: | 047-24002-000 |
| Деталь: | xxx |
| Парткод: | 059-37014-009 |
| Деталь: | N/A |
| Парткод: | 059-37009-005 |
| Деталь: | SUB PANEL UNIT, L/LL ENG. |
| Парткод: | 059-37010-003 |
| Деталь: | SUB PANEL UNIT, L/LL PIC. |
| Парткод: | 059-37011-000 |
| Деталь: | N/A |
| Парткод: | 059-37012-006 |
| Деталь: | SUB PANEL UNIT, L/LL B4 PIC. |
| Парткод: | 059-37015-005 |
| Деталь: | N/A |
| Парткод: | 059-37016-001 |
| Деталь: | N/A |
| Парткод: | 059-37017-008 |
| Деталь: | SUB PANEL UNIT, L/LL B4 ENG. |
| Парткод: | 059-37018-004 |
| Деталь: | N/A |
| Парткод: | 059-37019-000 |
| Деталь: | N/A |
| Парткод: | 059-37020-009 |
| Деталь: | N/A |
| Парткод: | 059-37021-005 |
| Деталь: | N/A |
| Парткод: | 059-37022-109 |
| Деталь: | N/A |
| Парткод: | 059-37023-105 |
| Деталь: | xxx |
| Парткод: | 059-37005-000 |
| Деталь: | PANEL UNIT |
| Парткод: | 059-37006-006 |
| Деталь: | xxx |
| Парткод: | 059-37007-002 |
| Деталь: | SQUEEGEE UNIT, A3 |
| Парткод: | 023-75090-107 |
| Деталь: | SQUEEGEE UNIT B4 |
| Парткод: | 023-75091-103 |
| Деталь: | SQUEEGEE UNIT, A4 |
| Парткод: | 023-75092-100 |
| Деталь: | BLOCK F, SQUEEGEE |
| Парткод: | 023-17041-104 |
| Деталь: | METAL, S4X7X2 |
| Парткод: | 607-03001-001 |
| Деталь: | O RING, P4-1.9 |
| Парткод: | 640-60040-000 |
| Деталь: | SIDE FRAME, SQUEEGEE F ASSY |
| Парткод: | 024-17126-107 |
| Деталь: | ADJ. PLATE R, SQUEEGEE GAP |
| Парткод: | 046-17331-000 |
| Деталь: | ADJ. PLATE L, SQUEEGEE GAP |
| Парткод: | 046-17332-006 |
| Деталь: | GEAR, M0.8X19X4 |
| Парткод: | 612-10027-008 |
| Деталь: | GEAR, M0.8X43X3 |
| Парткод: | 612-10028-101 |
| Деталь: | SIDE FRAME, SQUEEGEE R ASSY |
| Парткод: | 024-17125-100 |
| Деталь: | BLOCK R, SQUEEGEE |
| Парткод: | 023-17040-108 |
| Деталь: | GEAR, M1X25X7 OWC |
| Парткод: | 612-10024-106 |
| Деталь: | SHEET , SQUEEGEE ROLLER |
| Парткод: | 639-00004-003 |
| Деталь: | WASHER, 8X18.5X1 |
| Парткод: | 639-00003-007 |
| Деталь: | SQUEEGEE ROLLER |
| Парткод: | 023-17030-307 |
| Деталь: | SQUEEGEE ROLLER , B4 |
| Парткод: | 023-17230-209 |
| Деталь: | SQUEEGEE ROLLER , A4 |
| Парткод: | 023-17209-200 |
| Деталь: | DOCTOR ROLLER, ASSY , A3 |
| Парткод: | 023-17329-108 |
| Деталь: | DOCTOR ROLLER, ASSY , B4 |
| Парткод: | 023-17330-106 |
| Деталь: | DOCTOR ROLLER ASSY , A4 |
| Парткод: | 023-17331-102 |
| Деталь: | INK DRIVE SHAFT |
| Парткод: | 023-17035-104 |
| Деталь: | INK DRIVE SHAFT , B4 |
| Парткод: | 023-17239-109 |
| Деталь: | xxx |
| Парткод: | 023-17211-107 |
| Деталь: | SUPPORT BRACKET F , B4 |
| Парткод: | 023-17235-308 |
| Деталь: | SUPPORT BRACKET F , A4 |
| Парткод: | 023-17213-304 |
| Деталь: | SUPPORT BRACKET R , B4 |
| Парткод: | 023-17234-204 |
| Деталь: | SUPPORT BRACKET R , A4 |
| Парткод: | 023-17214-203 |
| Деталь: | PLATE, P-WASHER |
| Парткод: | 023-17423-007 |
| Деталь: | P WASHER, 8X16X0.4 |
| Парткод: | 639-00005-000 |
| Деталь: | PLATE, METAL, DRIVE SHAFT, DRUM |
| Парткод: | 023-17242-002 |
| Деталь: | Support plate A |
| Парткод: | 023-17421-004 |
| Деталь: | Support plate B |
| Парткод: | 023-17422-000 |
| Деталь: | COLLAR , INK DRIVE SHAFT |
| Парткод: | 023-17341-000 |
| Деталь: | Bottle Stay |
| Парткод: | 023-17025-206 |
| Деталь: | Ink Distributor |
| Парткод: | 030-16404-003 |
| Деталь: | INK DISTRIBUTOR ,A4 |
| Парткод: | 023-17212-006 |
| Деталь: | O RING , P10-2.4 |
| Парткод: | 640-60100-100 |
| Деталь: | GROUND PLATE, INK |
| Парткод: | 023-17254-000 |
| Деталь: | INK-SENSOR-PCB, A3 |
| Парткод: | 444-51005-208 |
| Деталь: | INK-SENSOR-PCB, B4 |
| Парткод: | 444-51006-204 |
| Деталь: | N/A |
| Парткод: | 059-75084-002 |
| Деталь: | CARTRIDGE GUIDE, LOWER |
| Парткод: | 059-17028-003 |
| Деталь: | MAINTENANCE CAP |
| Парткод: | 059-17027-007 |
| Деталь: | BRACKET, INK BOTTLE SET SW |
| Парткод: | 023-17158-109 |
| Деталь: | BOTTLE CATCH |
| Парткод: | 023-17157-102 |
| Деталь: | BOTTLE SET SW ASSY |
| Парткод: | 023-17965-209 |
| Деталь: | SHAFT, RF-TAG READER, DRUM |
| Парткод: | 023-17249-104 |
| Деталь: | ARM, RF MODULE |
| Парткод: | 046-17009-000 |
| Деталь: | MODULE HOLDER, R, DRUM |
| Парткод: | 046-17017-003 |
| Деталь: | MODULE HOLDER, F, DRUM |
| Парткод: | 046-17008-004 |
| Деталь: | CARTRIDGE GUIDE, UPPER |
| Парткод: | 059-17032-000 |
| Деталь: | RFID PCB UNIT |
| Парткод: | 050-75140-004 |
| Деталь: | SPRING, RF-TAG READER, DRUM |
| Парткод: | 023-17250-005 |
| Деталь: | Ink Pump Assy |
| Парткод: | 023-17145-406 |
| Деталь: | GEAR,M1X32X4 |
| Парткод: | 612-12306-001 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | NOZZEL,INK PUMP ASSY |
| Парткод: | 023-17425-000 |
| Деталь: | xxx |
| Парткод: | 059-53007-004 |
| Деталь: | N/A |
| Парткод: | 059-75088-008 |
| Деталь: | BASE, SEPARATION FAN |
| Парткод: | 059-21008-009 |
| Деталь: | FAN, E1033H24BYAZ-33 |
| Парткод: | 490-41014-104 |
| Деталь: | LIGHT ABSORBER STRIP(35X28) |
| Парткод: | 023-21393-007 |
| Деталь: | AIR NOZZLE |
| Парткод: | 059-21010-003 |
| Деталь: | WIRE HARNESS, SEPARATION FAN |
| Парткод: | 046-21800-103 |
| Деталь: | AIR HOSE, SEPARATOR |
| Парткод: | 023-21016-106 |
| Деталь: | Power Band T10 |
| Парткод: | 665-02901-100 |
| Деталь: | SEPARATOR |
| Парткод: | 024-21038-107 |
| Деталь: | SHAFT, SEPARATOR |
| Парткод: | 023-21006-100 |
| Деталь: | RELEASE LEVER, SEPARATOR |
| Парткод: | 023-21007-000 |
| Деталь: | METALF8X13/12X5, 16X2 |
| Парткод: | 651-00018-009 |
| Деталь: | ADJUSTMENT PLATE |
| Парткод: | 023-21003-004 |
| Деталь: | STOPPER, SEPARATOR |
| Парткод: | 023-21005-007 |
| Деталь: | STEPPED SCREW, M4X4.5 |
| Парткод: | 635-17614-205 |
| Деталь: | Fixing Pin |
| Парткод: | 020-13114-300 |
| Деталь: | SPACER, CYLINDER BASE, AIR PUMP |
| Парткод: | 023-21027-000 |
| Деталь: | AIR PUMP ASSY |
| Парткод: | 023-75077-100 |
| Деталь: | CYLINDER BASE BRACKET, AIR PUMP |
| Парткод: | 023-21013-506 |
| Деталь: | GEAR, M1X80X10 |
| Парткод: | 612-03106-105 |
| Деталь: | TIMING PLATE, AIR PUMP |
| Парткод: | 023-21023-200 |
| Деталь: | xxx |
| Парткод: | 019-13511-200 |
| Деталь: | CYLINDER, AIR PUMP |
| Парткод: | 023-21021-002 |
| Деталь: | CYLINDER VALVE II, AIR PUMP |
| Парткод: | 019-13517-004 |
| Деталь: | CYLINDER VALVE SHEET, AIR PUMP |
| Парткод: | 019-13518-000 |
| Деталь: | PISTON HEAD II, AIR PUMP |
| Парткод: | 019-13516-105 |
| Деталь: | O RING, 34-3.6 |
| Парткод: | 640-67340-009 |
| Деталь: | ARM SHAFT, AIR PUMP |
| Парткод: | 019-13512-002 |
| Деталь: | ADJ. VALVE, AIR BLOW |
| Парткод: | 023-21011-104 |
| Деталь: | SPRING, ADJ. VALVE, AIR BLOW |
| Парткод: | 023-21010-000 |
| Деталь: | ADJ. PLATE, AIR BLOW |
| Парткод: | 023-21009-002 |
| Деталь: | RELEASE PLATE |
| Парткод: | 023-21001-001 |
| Деталь: | WIRE HARNESS, PAPER EJECTION REAR |
| Парткод: | 059-53004-005 |
| Деталь: | FRAME, M-M UPPER UNIT |
| Парткод: | 023-28150-304 |
| Деталь: | SHAFT, HANDLE, M-M UP |
| Парткод: | 023-28157-007 |
| Деталь: | HOOK LEVER, M.-M UP |
| Парткод: | 059-28007-008 |
| Деталь: | HOOK, M.-M UP |
| Парткод: | 023-28237-000 |
| Деталь: | HOOK SPRING, M.-M UP |
| Парткод: | 023-28356-000 |
| Деталь: | PUSHING PLATE R, SET-GUIDE PLATE |
| Парткод: | 023-28253-103 |
| Деталь: | SPRING REAR, M.-M UP |
| Парткод: | 023-28156-000 |
| Деталь: | PIVOT SUPPORT PLATE REAR, M.-M UP |
| Парткод: | 023-28252-107 |
| Деталь: | SHAFT, M.-M UPPER UNIT |
| Парткод: | 023-28154-105 |
| Деталь: | PUSHING PLATE F2, SET-GUIDE PLATE |
| Парткод: | 046-28034-007 |
| Деталь: | SPRING FRONT, M.-M UP |
| Парткод: | 023-28155-004 |
| Деталь: | PIVOT SUPPORT PLATE FRONT, M.-M UP |
| Парткод: | 023-28151-106 |
| Деталь: | SAFETY STOPPER, M.-M UP |
| Парткод: | 023-28177-105 |
| Деталь: | SEAL, MASTER MAKING UNIT |
| Парткод: | 059-28028-005 |
| Деталь: | UPPER BRACKET A3, MASTER END SENSOR |
| Парткод: | 023-28418-005 |
| Деталь: | UPPER BRACKET B4, MASTER END SENSOR |
| Парткод: | 024-28177-005 |
| Деталь: | UPPER BRACKET A4, MASTER END SENSOR |
| Парткод: | 046-28036-000 |
| Деталь: | LIGHT ABSORBER STRIP(21X15) |
| Парткод: | 023-28431-001 |
| Деталь: | COVER, MASTER END SENSOR |
| Парткод: | 023-28427-004 |
| Деталь: | SENSOR (RCV), KH0854-01 |
| Парткод: | 444-42030-402 |
| Деталь: | BOTTOM COVER, TPH, M.-M. |
| Парткод: | 059-28006-001 |
| Деталь: | SPRING, TPH ALIGNMENT SHAFT |
| Парткод: | 023-28435-007 |
| Деталь: | xxx |
| Парткод: | 046-28008-006 |
| Деталь: | PRESSURE RELEASE PLATE, TPH PRESS |
| Парткод: | 023-28160-008 |
| Деталь: | PRESSURE LEVER BRACKET, M.-M UP |
| Парткод: | 023-28159-301 |
| Деталь: | TPH PRESSURE SPRING 40 |
| Парткод: | 023-28161-101 |
| Деталь: | TPH PRESSURE SPRING 30 |
| Парткод: | 023-28441-101 |
| Деталь: | TPH PRESSURE SPRING 23 |
| Парткод: | 023-28344-109 |
| Деталь: | TPH ALIGNMENT SHAFT |
| Парткод: | 023-28173-100 |
| Деталь: | METAL, F10X14X10, 18X2 |
| Парткод: | 607-10008-003 |
| Деталь: | Lock Ring |
| Парткод: | 019-11812-106 |
| Деталь: | BRACKET, TPH DRAWER CONNECTOR UP |
| Парткод: | 023-28382-205 |
| Деталь: | SPRING, DRAWER CONNECTER |
| Парткод: | 023-28078-000 |
| Деталь: | STEPPED SCREW, F4X4.5, M3X4 |
| Парткод: | 635-10002-000 |
| Деталь: | WIRE HARNESS , TPH DRAWER U , H |
| Парткод: | 048-28002-207 |
| Деталь: | SPACER 2, M.-M.UNIT |
| Парткод: | 046-28052-005 |
| Деталь: | BRACKET, M.-M. UNIT SET SW |
| Парткод: | 046-28050-002 |
| Деталь: | DE-ELECTRICITY BRUSH, A3 |
| Парткод: | 023-28410-101 |
| Деталь: | WIRE HARNESS, M-M UNIT RELAY |
| Парткод: | 059-53018-006 |
| Деталь: | GEAR COVER, M.-M UP |
| Парткод: | 023-28328-103 |
| Деталь: | SEAL, TPH CLEANING, PIC. |
| Парткод: | 023-28942-200 |
| Деталь: | xxx |
| Парткод: | 023-75143-103 |
| Деталь: | BRACKET, TPH PRESSURE MOTOR |
| Парткод: | 023-28168-106 |
| Деталь: | CAM, TPH PRESSURE |
| Парткод: | 023-28165-000 |
| Деталь: | GEAR, M1X20X6 |
| Парткод: | 612-10010-008 |
| Деталь: | SHAFT, TPH PRESSURE CAM |
| Парткод: | 023-28166-103 |
| Деталь: | METAL, F6X10/9X4, 12X1.5 |
| Парткод: | 607-13000-402 |
| Деталь: | PRESSURE DETECTION ASSY |
| Парткод: | 054-28005-106 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | SHAFT, GEAR, TPH LIFT MOTOR |
| Парткод: | 023-28213-306 |
| Деталь: | GEAR, M0.8X25+M0.8X14 |
| Парткод: | 612-80006-008 |
| Деталь: | SHAFT, GEAR 8, TPH LIFT MOTOR |
| Парткод: | 023-28433-004 |
| Деталь: | GEAR, M0.8X25+M1X14 |
| Парткод: | 612-80007-004 |
| Деталь: | GEAR, M0.8X20+M0.8X14 |
| Парткод: | 612-80008-000 |
| Деталь: | MOTOR ASSY (CWRS-445PA) |
| Парткод: | 023-75906-000 |
| Деталь: | SUPPORT, CLAMP WORM |
| Парткод: | 030-19205-001 |
| Деталь: | HOLDING PLATE, WORM GEAR |
| Парткод: | 023-28172-006 |
| Деталь: | SEAL, TPH, ENG. |
| Парткод: | 023-28424-005 |
| Деталь: | SEAL, TPH, PIC |
| Парткод: | 023-28423-009 |
| Деталь: | TPH PRESSURE SPRING, 50 |
| Парткод: | 045-28004-100 |
| Деталь: | TPH DRAWER CONNECTOR U (G) |
| Парткод: | 046-28037-006 |
| Деталь: | REAR FRAME, M.-M UNIT |
| Парткод: | 023-28092-207 |
| Деталь: | FRONT FRAME, M.-M. UNIT |
| Парткод: | 023-75165-107 |
| Деталь: | SHAFT, HANDLE, M-M |
| Парткод: | 023-28338-001 |
| Деталь: | HANDLE, M.-M. |
| Парткод: | 023-28070-106 |
| Деталь: | GUIDE, HANDLE, M.-M. |
| Парткод: | 059-28005-005 |
| Деталь: | HOOK LEFT, HANDLE, M.-M. |
| Парткод: | 023-28206-105 |
| Деталь: | HOOK RIGHT, HANDLE, M.-M. |
| Парткод: | 023-28071-102 |
| Деталь: | ACTUATOR PLATE, M.-M. SET SENSOR |
| Парткод: | 023-28207-004 |
| Деталь: | SPRING, HOOK, M-M |
| Парткод: | 023-28072-001 |
| Деталь: | HANDLE STOPPER, M.-M. |
| Парткод: | 023-28336-009 |
| Деталь: | STEPPED SCREW, F4X2.2, M3X4 |
| Парткод: | 635-17423-108 |
| Деталь: | SPRING, HANDLE, M-M |
| Парткод: | 023-28209-007 |
| Деталь: | TPH303R16 |
| Парткод: | 444-80007-309 |
| Деталь: | BOTTOM STAY, M.-M UNIT |
| Парткод: | 023-28013-200 |
| Деталь: | SLIDE GUIDE 2, M.-M. |
| Парткод: | 023-28251-003 |
| Деталь: | REINFORCEMENT PLATE, M.-M. FRAME |
| Парткод: | 023-28074-101 |
| Деталь: | LOWER STAY, M.-MAKING |
| Парткод: | 023-28073-008 |
| Деталь: | REINFORCE PLATE, LOWER, M.-M. UNIT |
| Парткод: | 023-28245-003 |
| Деталь: | MASTER ROLL HOLDER, BOTTOM |
| Парткод: | 059-28012-001 |
| Деталь: | MASTER GUIDE ROLLER |
| Парткод: | 023-28210-005 |
| Деталь: | BOX STAY, M.-MAKING |
| Парткод: | 023-28015-008 |
| Деталь: | DE-ELECTRICITY BAR, M.-M., A3 |
| Парткод: | 014-15011-004 |
| Деталь: | LOWER BRACKET, MASTER END SENSOR |
| Парткод: | 023-28417-009 |
| Деталь: | END SENSOR PCB |
| Парткод: | 451-40011-006 |
| Деталь: | xxx |
| Парткод: | 607-16001-000 |
| Деталь: | BRACKET F, WRITE ROLLER |
| Парткод: | 046-28013-000 |
| Деталь: | PULLEY, P70-2GT-5 |
| Парткод: | 611-90012-009 |
| Деталь: | BRACKET R, WRITE ROLLER |
| Парткод: | 046-28012-003 |
| Деталь: | SUPPORT PLATE, REAR FRAME, M.-M |
| Парткод: | 023-28378-100 |
| Деталь: | STOCKER ROLLER, A3 |
| Парткод: | 046-28014-006 |
| Деталь: | STOCKER ROLLER, B4 |
| Парткод: | 046-28021-002 |
| Деталь: | METAL, F6X8X4, 10X1 |
| Парткод: | 607-10006-000 |
| Деталь: | M SET GUIDE PLATE B, A3 |
| Парткод: | 023-28114-308 |
| Деталь: | M SET GUIDE PLATE B, B4 |
| Парткод: | 023-28259-306 |
| Деталь: | M SET GUIDE PLATE B, A4 |
| Парткод: | 023-28302-309 |
| Деталь: | SPRING B FRONT, M SET GUIDE PLATE |
| Парткод: | 023-28115-304 |
| Деталь: | SHAFT, M SET GUIDE PLATE |
| Парткод: | 023-28036-102 |
| Деталь: | MASTER FRANGE, FRONT(G) |
| Парткод: | 059-28019-006 |
| Деталь: | RFMB5J-0171, SU |
| Парткод: | 046-75512-006 |
| Деталь: | MODULE HOLDER, M.-M. |
| Парткод: | 046-28033-000 |
| Деталь: | None |
| Парткод: | 059-28022-007 |
| Деталь: | N/A |
| Парткод: | 059-28023-003 |
| Деталь: | ADJUSTER COLLAR, MASTER HOLDER |
| Парткод: | 059-28027-009 |
| Деталь: | SPRING COLLAR, MASTER HOLDER |
| Парткод: | 023-28440-000 |
| Деталь: | STOPPER REAR, M.-M UNIT |
| Парткод: | 023-28247-103 |
| Деталь: | BRACKET, STOPPER, M SET GUIDE PLATE |
| Парткод: | 023-28396-001 |
| Деталь: | SHAFT, STOPPER, M SET GUIDE PLATE |
| Парткод: | 023-28397-008 |
| Деталь: | STOPPER, M SET GUIDE PLATE |
| Парткод: | 023-28398-004 |
| Деталь: | STOPPER SPRING, M SET GUIDE PLATE |
| Парткод: | 023-28399-000 |
| Деталь: | REAR COVER, M.-M. UNIT |
| Парткод: | 054-28009-004 |
| Деталь: | STOPPER SPRING, M.-M CLOSE |
| Парткод: | 023-28233-005 |
| Деталь: | BASE BRACKET, STOPPER, M.-M. CLOSE |
| Парткод: | 023-28232-009 |
| Деталь: | STOPPER, M.-M. CLOSE |
| Парткод: | 023-28231-002 |
| Деталь: | STEPPED SCREW, 6X1.8, M3X4 |
| Парткод: | 635-17613-101 |
| Деталь: | WIRE HARNESS, RF, M.-M. |
| Парткод: | 046-28038-002 |
| Деталь: | None |
| Парткод: | 047-28041-000 |
| Деталь: | N/A |
| Парткод: | 059-75104-003 |
| Деталь: | STAGE COVER |
| Парткод: | 023-30008-108 |
| Деталь: | N/A |
| Парткод: | 059-30008-003 |
| Деталь: | ORIGINAL HOLDER COVER, STAGE COVER |
| Парткод: | 059-30006-000 |
| Деталь: | STAGE COVER HINGE ASSY |
| Парткод: | 059-30021-000 |
| Деталь: | STAGE PAD, STAGE COVER |
| Парткод: | 059-30009-000 |
| Деталь: | Pen Case , Digitizer |
| Парткод: | 045-36031-001 |
| Деталь: | SIDE FRAME, F1, M.-RMV |
| Парткод: | 046-24002-100 |
| Деталь: | SIDE FRAME, R1, M.-RMV. |
| Парткод: | 046-24009-008 |
| Деталь: | STAY A, M.-RMV. |
| Парткод: | 046-24016-101 |
| Деталь: | STAY B, M.-RMV. |
| Парткод: | 046-24017-000 |
| Деталь: | BRACKET, M.-RMV. UNIT |
| Парткод: | 046-24086-002 |
| Деталь: | M COMPRESSION PLATE |
| Парткод: | 046-24099-104 |
| Деталь: | METAL, F10X15/14X6, 18X2 |
| Парткод: | 607-16001-000 |
| Деталь: | GEAR, M1X71X14 |
| Парткод: | 612-10040-004 |
| Деталь: | BRACKET, GEAR A |
| Парткод: | 024-24138-005 |
| Деталь: | BRACKET, GEAR B |
| Парткод: | 024-24139-001 |
| Деталь: | MASTER REMOVAL ROLLER |
| Парткод: | 046-24005-002 |
| Деталь: | HOOK SHAFT, M REMOVAL ROLLER LOWER |
| Парткод: | 023-24124-104 |
| Деталь: | HOLDING PLATE F, M.-RMV. |
| Парткод: | 046-24125-000 |
| Деталь: | GUIDE STAY, M.-RMV. |
| Парткод: | 046-24152-005 |
| Деталь: | GUIDE PLATE, M.-RMV. |
| Парткод: | 046-24151-106 |
| Деталь: | HOLDING PLATE R, M.-RMV. |
| Парткод: | 046-24127-000 |
| Деталь: | STEPPED SCREW, F5X10.8, M3X3 |
| Парткод: | 635-10006-005 |
| Деталь: | ROLLER, HOOK, M.-RMV. |
| Парткод: | 023-24126-000 |
| Деталь: | METALF8X13/12X5, 16X2 |
| Парткод: | 651-00018-009 |
| Деталь: | GEAR, M1.25X16+M1.25X14 |
| Парткод: | 612-80025-002 |
| Деталь: | N/A |
| Парткод: | 059-24006-007 |
| Деталь: | MANUAL COMPRESSION LEVER |
| Парткод: | 023-24120-001 |
| Деталь: | LINK PLATE |
| Парткод: | 024-25065-109 |
| Деталь: | xxx |
| Парткод: | 046-24113-107 |
| Деталь: | KNOB, RELEASE LEVER, M.-RMV. |
| Парткод: | 023-24117-000 |
| Деталь: | BRACKET, FG SENSOR, 1, M.-RMV. |
| Парткод: | 046-24075-000 |
| Деталь: | N/A |
| Парткод: | 059-24005-000 |
| Деталь: | BRACKET, SET SENSOR, DISPOSAL BOX |
| Парткод: | 046-24015-008 |
| Деталь: | SUCTION MOTOR, CCWRS-55PH |
| Парткод: | 023-75907-006 |
| Деталь: | METAL SLIT, MOTOR |
| Парткод: | 023-21342-305 |
| Деталь: | PULLEY GEAR, 0.8X31+53S2M |
| Парткод: | 613-11300-007 |
| Деталь: | BELT, 40-S2M-290 |
| Парткод: | 621-00030-000 |
| Деталь: | BRACKET, M.-RMV. GEAR |
| Парткод: | 046-24001-007 |
| Деталь: | GEAR, M0.8X61+M1.25X12 |
| Парткод: | 612-80024-006 |
| Деталь: | MOTOR ASSY (CWRS-445PA) |
| Парткод: | 023-75906-000 |
| Деталь: | BRACKET, MOTOR, M COMPRESSION |
| Парткод: | 046-24092-002 |
| Деталь: | GEAR, M0.8X35+M0.8X15 |
| Парткод: | 612-81303-006 |
| Деталь: | BRACKET, FG SENSOR, M COMPRESSION |
| Парткод: | 046-24074-004 |
| Деталь: | BRACKET, 1, M COMPRESSION GEAR |
| Парткод: | 046-24097-004 |
| Деталь: | BRACKET, LOCKING BOSS |
| Парткод: | 046-24012-009 |
| Деталь: | GEAR, M1X17+M0.8X61 |
| Парткод: | 612-81602-003 |
| Деталь: | GEAR, M0.8X17+M0.8X49 |
| Парткод: | 612-81401-008 |
| Деталь: | GEAR, M0.8X15X7 |
| Парткод: | 612-11103-000 |
| Деталь: | xxx |
| Парткод: | 046-24135-003 |
| Деталь: | STEPPED SCREW, F5X1.5, M3X3 |
| Парткод: | 635-18513-003 |
| Деталь: | SPRING, CLAMP CAM |
| Парткод: | 023-26020-004 |
| Деталь: | WIRE, MACHINE SET SW |
| Парткод: | 058-53011-004 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | EDGING SADDLE, LES-1010 |
| Парткод: | 665-00312-000 |
| Деталь: | N/A |
| Парткод: | 059-53010-005 |
| Деталь: | WIRE HARNESS, ELEVATOR MOTOR |
| Парткод: | 023-12602-108 |
| Деталь: | WIRE HARNESS, M-RMV |
| Парткод: | 059-53011-001 |
| Деталь: | WIRE HARNESS, FB UPPER |
| Парткод: | 059-53008-000 |
| Деталь: | SHAFT HOLDER, RIGHT |
| Парткод: | 046-28002-008 |
| Деталь: | SHAFT HOLDER, LEFT |
| Парткод: | 046-28003-004 |
| Деталь: | SHAFT, DRAWER CONNECTOR, M.-M UNIT |
| Парткод: | 023-28076-104 |
| Деталь: | HOOK SHAFT, M.-M UNIT |
| Парткод: | 023-28148-008 |
| Деталь: | UPPER STAY, M.-M UNIT |
| Парткод: | 023-28014-109 |
| Деталь: | GUIDE BLOCK, M.-M. UNIT MOUNT |
| Парткод: | 023-28367-001 |
| Деталь: | M. LOADING ROLLER, A3 |
| Парткод: | 023-28046-205 |
| Деталь: | M. LOADING ROLLER, B4 |
| Парткод: | 023-28285-200 |
| Деталь: | LOCK RING 4 |
| Парткод: | 023-17197-007 |
| Деталь: | GEAR, M0.8X13X5 |
| Парткод: | 612-10103-006 |
| Деталь: | SHAFT, M. LOADING ROLLER |
| Парткод: | 023-28044-105 |
| Деталь: | BRACKET, DE-ELECT. BRUSH, M LOADING |
| Парткод: | 023-28405-108 |
| Деталь: | DE-ELECTRICITY BRUSH, M LOADING |
| Парткод: | 023-28415-200 |
| Деталь: | LOAD ROLLER, A3 |
| Парткод: | 046-28015-100 |
| Деталь: | LOAD ROLLER, B4 |
| Парткод: | 046-28022-203 |
| Деталь: | METAL, F8X10X3, 11.2X0.6 |
| Парткод: | 607-10005-004 |
| Деталь: | GEAR, M0.8X16X5 |
| Парткод: | 612-10104-002 |
| Деталь: | FULCRUM PLATE, MASTER STOCKER |
| Парткод: | 046-28055-004 |
| Деталь: | DAMPER, OG8G-C |
| Парткод: | 610-00024-006 |
| Деталь: | BRACKET, GEAR SHAFT, M LOADING |
| Парткод: | 023-28376-108 |
| Деталь: | GEAR, M0.8X34X4 |
| Парткод: | 612-10106-005 |
| Деталь: | GEAR, M0.8X16X4 |
| Парткод: | 612-10105-009 |
| Деталь: | BRACKET, SET SENSOR, M.-M UPPER |
| Парткод: | 046-28045-106 |
| Деталь: | SENSOR, ON-171-A8 |
| Парткод: | 444-33003-206 |
| Деталь: | xxx |
| Парткод: | 046-28026-004 |
| Деталь: | WIRE HARNESS, M-M UNIT STAY PLATE |
| Парткод: | 059-53019-002 |
| Деталь: | LOAD MOTOR ASSY |
| Парткод: | 023-75144-100 |
| Деталь: | BRACKET, LOAD PULSE MOTOR |
| Парткод: | 023-28196-002 |
| Деталь: | MOTOR, PM42L-048-ZVS6 |
| Парткод: | 490-33015-100 |
| Деталь: | GEAR, MX0.5X89+M0.8X34 |
| Парткод: | 612-80019-002 |
| Деталь: | GEAR, M0.8X36+M0.8X18 |
| Парткод: | 612-80018-006 |
| Деталь: | MASTER GUIDE ASSY |
| Парткод: | 023-75140-104 |
| Деталь: | MASTER GUIDE ASSY MLB4 |
| Парткод: | 023-75142-107 |
| Деталь: | xxx |
| Парткод: | 023-75141-100 |
| Деталь: | METAL, F6X8X4, 10X1 |
| Парткод: | 607-10006-000 |
| Деталь: | CUTTER GUIDE UPPER, A3 |
| Парткод: | 023-28057-002 |
| Деталь: | CUTTER GUIDE UPPER, B4R |
| Парткод: | 023-28436-003 |
| Деталь: | CUTTER GUIDE UPPER, B4 |
| Парткод: | 023-28265-209 |
| Деталь: | CUTTER GUIDE LOWER, A3 |
| Парткод: | 023-28058-106 |
| Деталь: | CUTTER GUIDE LOWER, B4R |
| Парткод: | 023-28437-204 |
| Деталь: | CUTTER GUIDE LOWER, B4 |
| Парткод: | 023-28263-109 |
| Деталь: | SHAFT, STOKER ROLLER UPPER, A3 |
| Парткод: | 023-28184-004 |
| Деталь: | SHAFT, STOKER ROLLER UPPER, B4 |
| Парткод: | 023-28272-108 |
| Деталь: | M TRANSFER ROLLER, WIDE WIDTH |
| Парткод: | 023-28190-101 |
| Деталь: | xxx |
| Парткод: | 023-28191-108 |
| Деталь: | SHAFT, LOAD ROLLER UPPER, A3 |
| Парткод: | 023-28093-009 |
| Деталь: | SHAFT, LOAD ROLLER UPPER, B4 |
| Парткод: | 023-28286-201 |
| Деталь: | M TRANSFER ROLLER, SHORT WIDTH |
| Парткод: | 023-28192-104 |
| Деталь: | SENSOR, E-3674 |
| Парткод: | 444-39000-004 |
| Деталь: | GUIDE, MASTER LOADING |
| Парткод: | 059-28014-004 |
| Деталь: | CUTTER UNIT(ROTARY) |
| Парткод: | 023-28444-006 |
| Деталь: | CUTTER UNIT(SHUTTLE) |
| Парткод: | 023-28422-606 |
| Деталь: | CUTTER SW ASSY |
| Парткод: | 023-75914-002 |
| Деталь: | MASTER GUIDE PLATE A, A3(D23) |
| Парткод: | 023-28327-204 |
| Деталь: | MASTER GUIDE PLATE A, B4(D23) |
| Парткод: | 023-28310-000 |
| Деталь: | SEAL, POS. LEADING EDGE OF MASTER, |
| Парткод: | 023-28946-109 |
| Деталь: | STEPPED SCREW, F5X3, M3X3 |
| Парткод: | 635-10007-001 |
| Деталь: | Cutter cover |
| Парткод: | 046-28043-006 |
| Деталь: | CUTTER COVER, 2 |
| Парткод: | 046-28044-002 |
| Деталь: | COVER, MASTER POS. SENSOR |
| Парткод: | 023-28053-104 |
| Деталь: | MASTER SET GUIDE BAR |
| Парткод: | 059-28008-004 |
| Деталь: | None |
| Парткод: | 059-28026002 |
| Деталь: | GUIDE PLATE B, MASTER SET GUIDE BAR |
| Парткод: | 023-28409-103 |
| Деталь: | GUIDE PLATE A, MASTER SET GUIDE BAR |
| Парткод: | 023-28280-100 |
| Деталь: | SPRING, SAFETY SW |
| Парткод: | 046-28049-004 |
| Деталь: | BRACKET, SW, M.-M. |
| Парткод: | 046-28048-008 |
| Деталь: | VER. PRINT POS. BASE ASSY |
| Парткод: | 023-75094-102 |
| Деталь: | PRINT POSITIONING BASE |
| Парткод: | 023-15034-208 |
| Деталь: | COVER, PAPER FEED DRIVE |
| Парткод: | 023-15115-100 |
| Деталь: | BRACKET, TIMING ROLLER |
| Парткод: | 023-15078-000 |
| Деталь: | ARM FRONT, VER. PRINT POS. |
| Парткод: | 023-15104-400 |
| Деталь: | GEAR, M1X140X8 |
| Парткод: | 612-10016-103 |
| Деталь: | ARM REAR, VER. PRINT POS. |
| Парткод: | 023-15105-008 |
| Деталь: | GEAR,M1X42+M1X28 |
| Парткод: | 612-80017-107 |
| Деталь: | SECTOR GEAR, VER. PRINT POSITION |
| Парткод: | 023-15068-005 |
| Деталь: | COVER, VER. PRINT POS. PLANET GEAR |
| Парткод: | 023-15103-005 |
| Деталь: | GEAR, M1X126X7.5 |
| Парткод: | 612-10014-003 |
| Деталь: | GEAR BASE BLOCK, VERTICAL GEAR |
| Парткод: | 023-15098-206 |
| Деталь: | TIMING CAM |
| Парткод: | 023-15056-201 |
| Деталь: | SECTOR CAM |
| Парткод: | 023-15055-108 |
| Деталь: | IDLER SPRING, VERTICAL |
| Парткод: | 023-15070-000 |
| Деталь: | GEAR,M0.8X36X10 |
| Парткод: | 612-10013-007 |
| Деталь: | GEAR, M0.8X35+M0.8X15 |
| Парткод: | 612-81303-006 |
| Деталь: | MOTOR, PM42L-048-ZVN5 |
| Парткод: | 490-33016-106 |
| Деталь: | BRACKET, VERTICAL CENTERING SENSOR |
| Парткод: | 023-15116-000 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | WIRE HARNESS, PAPER FEED REAR |
| Парткод: | 059-53005-001 |
| Деталь: | WIRE HARNESS, FB UPPER |
| Парткод: | 059-53008-000 |
| Деталь: | BRACKET, VER. PRINT POS. BASE |
| Парткод: | 023-15117-006 |
| Деталь: | COVER STAY, PAPER FEED DRIVE |
| Парткод: | 023-15072-002 |
| Деталь: | xxx |
| Парткод: | 046-53012-000 |
| Деталь: | JUNCTION WIRE HARNESS ,SAFETY SW,LL |
| Парткод: | 046-12708-105 |
| Деталь: | N/A |
| Парткод: | 059-75101-004 |
| Деталь: | N/A |
| Парткод: | 059-75102-000 |
| Деталь: | N/A |
| Парткод: | 059-75100-008 |
| Деталь: | PRESSURE ROLLER ASSY II, B4(20) |
| Парткод: | 023-75158-100 |
| Деталь: | PRESSURE SHAFT |
| Парткод: | 046-19003-000 |
| Деталь: | STRIPPER PAD,U |
| Парткод: | 019-11834-002 |
| Деталь: | STOPPER, PRESSURE ROLLER |
| Парткод: | 045-19012-001 |
| Деталь: | SUPPORT SHAFT, PRESSURE |
| Парткод: | 046-19001-007 |
| Деталь: | PRESSURE ROLLER SUPPORT,FRONT ASSY |
| Парткод: | 023-75071-102 |
| Деталь: | PRESSURE ROLLER SUPPORT,REAR ASSY |
| Парткод: | 023-75072-109 |
| Деталь: | STEPPED SCREW,6X1.8,M3X4 |
| Парткод: | 635-17613-101 |
| Деталь: | PRESSURE ROLLER A3 |
| Парткод: | 023-74068-000 |
| Деталь: | PRESSURE ROLLER B4 |
| Парткод: | 023-74069-007 |
| Деталь: | PRESSURE ROLLER A4 |
| Парткод: | 023-74074-000 |
| Деталь: | PRESSURE ROLLER ASSY,B4 20 |
| Парткод: | 023-75160-105 |
| Деталь: | METAL,F16X22/19X6,26X2 |
| Парткод: | 607-10003-001 |
| Деталь: | Timing Roller Assy |
| Парткод: | 023-75093-106 |
| Деталь: | TIMING ROLLER |
| Парткод: | 023-12501-107 |
| Деталь: | BEARING, TIMING ROLLER |
| Парткод: | 023-12503-100 |
| Деталь: | GEAR, M1X15X12 |
| Парткод: | 612-02101-207 |
| Деталь: | METAL,F10X15/14X6,18X2 |
| Парткод: | 607-16001-000 |
| Деталь: | ADJ. PLATE, TIMING ROLLER |
| Парткод: | 023-12507-105 |
| Деталь: | P WASHER, 6X13.5X1 |
| Парткод: | 639-00610-000 |
| Деталь: | BEARING, DDLF-1910ZZR |
| Парткод: | 601-10195-004 |
| Деталь: | None |
| Парткод: | 055-12112-104 |
| Деталь: | COLLAR, LOAD SPRING |
| Парткод: | 023-12510-009 |
| Деталь: | FIX PLATE, LOAD SPRING |
| Парткод: | 030-14458-300 |
| Деталь: | TUBE,3X5 |
| Парткод: | 030-14480-004 |
| Деталь: | GUIDE ROLLER ASSY |
| Парткод: | 023-75080-101 |
| Деталь: | Guide Roller |
| Парткод: | 023-12511-102 |
| Деталь: | SUPPORT F, GUIDE ROLLER |
| Парткод: | 023-12515-000 |
| Деталь: | ADJ. PLATE, GUIDE ROLLER |
| Парткод: | 023-12545-007 |
| Деталь: | METAL,F8X11/10X5.5,14X2 |
| Парткод: | 607-40001-003 |
| Деталь: | LOCK PLATE, GUIDE ROLLER |
| Парткод: | 023-12519-006 |
| Деталь: | SUPPORT R, GUIDE ROLLER |
| Парткод: | 023-12516-104 |
| Деталь: | JUNCTION WIRE HARNESS ,SAFETY SW,LL |
| Парткод: | 046-12708-105 |
| Деталь: | SHAFT, GUIDE ROLLER |
| Парткод: | 023-12512-206 |
| Деталь: | PRESSURE PLATE, GUIDE ROLLER |
| Парткод: | 023-12514-209 |
| Деталь: | STAY HOLDER, GUIDE PLATE |
| Парткод: | 023-12537-101 |
| Деталь: | N/A |
| Парткод: | 059-75108-009 |
| Деталь: | SENSOR (RCV), OF-11R1-N23 |
| Парткод: | 444-32007-003 |
| Деталь: | WIRE HARNESS, PAPER SENSOR U |
| Парткод: | 046-12702-000 |
| Деталь: | Guide Plate (Lower) |
| Парткод: | 046-12503-007 |
| Деталь: | GUIDE PLATE (UPPER) |
| Парткод: | 023-12533-408 |
| Деталь: | COVER, PAPER SENSOR (UPPER) |
| Парткод: | 046-12501-004 |
| Деталь: | None |
| Парткод: | 046-12502-108 |
| Деталь: | SENSOR, OF-11T-N23, (LOWER) |
| Парткод: | 444-32006-007 |
| Деталь: | JUNCTION HARNESS, PAPER SENSOR (LOW |
| Парткод: | 046-12704-002 |
| Деталь: | WIRE HARNESS, PAPER SENSOR (LOWER) |
| Парткод: | 046-12703-006 |
| Деталь: | BACK COVER, STRIPPER UNIT |
| Парткод: | 059-12003-002 |
| Деталь: | N/A |
| Парткод: | 059-75106-006 |
| Деталь: | SPRING, ANGLE ADJ., STRIPPER |
| Парткод: | 023-12429-201 |
| Деталь: | SPRING TENSION, STRIPPER |
| Парткод: | 023-12403-008 |
| Деталь: | STRIPPER SUPPORT, RZ-L |
| Парткод: | 023-12425-303 |
| Деталь: | GUIDE BLOCK FRONT, STRIPPER UNIT |
| Парткод: | 023-12431-001 |
| Деталь: | N/A |
| Парткод: | 060-12123-009 |
| Деталь: | FIXED BLOCK |
| Парткод: | 052-12010-105 |
| Деталь: | N/A |
| Парткод: | 060-12122-002 |
| Деталь: | GROUND SPRING,ROLLER SYSTEM |
| Парткод: | 018-31614-001 |
| Деталь: | ARM, STRIPPER PRESSURE |
| Парткод: | 023-12412-007 |
| Деталь: | BRACKET, STRIPPER BASE |
| Парткод: | 023-12402-109 |
| Деталь: | STRIPPER ASSY RZ |
| Парткод: | 023-12434-000 |
| Деталь: | COVER F,STRIPPER PAD |
| Парткод: | 019-11832-107 |
| Деталь: | BASE F,STRIPPER PAD |
| Парткод: | 019-11831-100 |
| Деталь: | STRIPPER PAD,70 |
| Парткод: | 019-11833-006 |
| Деталь: | STEPPED SCREW:6X2.2,M4X2.5 |
| Парткод: | 635-00002-001 |
| Деталь: | BRACKET, HOOK, STRIPPER PRESSURE |
| Парткод: | 023-12427-101 |
| Деталь: | WORM GEAR BOX, STRIPPER UNIT |
| Парткод: | 023-12409-308 |
| Деталь: | N/A |
| Парткод: | 060-12124-005 |
| Деталь: | SUPPORT R, GUIDE ROLLER |
| Парткод: | 023-12548-006 |
| Деталь: | BRACKET, SWITCH |
| Парткод: | 024-28059-100 |
| Деталь: | DRUM SAFETY SW |
| Парткод: | 023-53024-100 |
| Деталь: | None |
| Парткод: | 059-12004-009 |
| Деталь: | SPRING, SAFETY SW/DRUM & MM |
| Парткод: | 023-28403-105 |
| Деталь: | None |
| Парткод: | 052-12015-000 |
| Деталь: | None |
| Парткод: | 052-12019-005 |
| Деталь: | CLAMP UNIT II |
| Парткод: | 046-75015-002 |
| Деталь: | CLAMP CAM ASSY II |
| Парткод: | 046-75006-003 |
| Деталь: | GEAR, M1X31X6 |
| Парткод: | 612-12315-000 |
| Деталь: | DISC, CLAMP SENSOR ASSY |
| Парткод: | 023-75152-102 |
| Деталь: | CLAMP MOTOR ASSY |
| Парткод: | 023-75070-106 |
| Деталь: | BRACKET PLATE, CLAMP DRIVE |
| Парткод: | 023-26000-100 |
| Деталь: | GEAR, M0.8X37+M1X15 |
| Парткод: | 612-11304-005 |
| Деталь: | GEAR, M0.8X35+M0.8X15 |
| Парткод: | 612-81303-006 |
| Деталь: | SUPPORT, CLAMP WORM |
| Парткод: | 030-19205-001 |
| Деталь: | MOTOR ASSY (CWRS-445PA) |
| Парткод: | 023-75906-000 |
| Деталь: | BRACKET, CLAMP SENSOR |
| Парткод: | 023-26005-005 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | WIRE HARNESS, CLAMP UNIT |
| Парткод: | 023-26018-000 |
| Деталь: | BEARING, MAIN SHAFT |
| Парткод: | 023-15001-008 |
| Деталь: | MAIN COVER, DRIVE |
| Парткод: | 023-15108-201 |
| Деталь: | SUPPORT PLATE, MAIN MOTOR |
| Парткод: | 030-12235-304 |
| Деталь: | BRACKET, PRESSURE SHAFT |
| Парткод: | 023-15012-000 |
| Деталь: | TENSIONER LEVER, MAIN BELT |
| Парткод: | 023-15006-204 |
| Деталь: | STEPPED SCREW ,F8X2.3 , M4X4.4 |
| Парткод: | 635-00004-004 |
| Деталь: | PULLEY, P18-5GT-12 |
| Парткод: | 611-90006-009 |
| Деталь: | N/A |
| Парткод: | 059-75113-002 |
| Деталь: | N/A |
| Парткод: | 059-75114-009 |
| Деталь: | N/A |
| Парткод: | 059-75116-001 |
| Деталь: | JOINT COLLAR, DRIVE |
| Парткод: | 023-15089-002 |
| Деталь: | SHAFT JOINT, DRIVE |
| Парткод: | 023-15003-108 |
| Деталь: | MAIN SHAFT, DRIVE |
| Парткод: | 023-15002-004 |
| Деталь: | MAIN GEAR, DRIVE |
| Парткод: | 023-15121-100 |
| Деталь: | PULLEY, P42-5GT |
| Парткод: | 611-90007-102 |
| Деталь: | ACTUATOR, B POSITION SENSOR |
| Парткод: | 023-15046-001 |
| Деталь: | PRESSURE CAM, A3 |
| Парткод: | 045-15011-000 |
| Деталь: | N/A |
| Парткод: | 045-15129-001 |
| Деталь: | PRESSURE CAM, A4 |
| Парткод: | 023-15128-008 |
| Деталь: | PRESSURE CAM, LEDGER |
| Парткод: | 045-15126-002 |
| Деталь: | BRACKET, B POSITION SENSOR |
| Парткод: | 023-15150-003 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | TPH Drawer Connector H (G) |
| Парткод: | 059-53014-000 |
| Деталь: | None |
| Парткод: | 607-10003-001 |
| Деталь: | PRESSURE LEVER, CAM |
| Парткод: | 059-15005-006 |
| Деталь: | SPRING, CAM FOLLOWER |
| Парткод: | 045-15145-007 |
| Деталь: | PRESSURE LEVER, SPRING |
| Парткод: | 059-15003-003 |
| Деталь: | SHOCK ABSORVER HOLDER PRESSURE LEV |
| Парткод: | 046-15008-007 |
| Деталь: | SHOCK ABSORVER PAD PRESSURE LEVER 2 |
| Парткод: | 046-15009-003 |
| Деталь: | BELT, 645-5GT-10 |
| Парткод: | 620-00010-001 |
| Деталь: | N/A |
| Парткод: | 059-75107-002 |
| Деталь: | N/A |
| Парткод: | 451-00011-003 |
| Деталь: | BRACKET, MAIN MOTOR |
| Парткод: | 023-15047-105 |
| Деталь: | JUNCTION WIRE HARNESS ,SAFETY SW,LL |
| Парткод: | 046-12708-105 |
| Деталь: | PULLEY, P42-5GT-13 |
| Парткод: | 611-90008-109 |
| Деталь: | WIRE HARNESS, PAPER EJECTION REAR |
| Парткод: | 059-53004-005 |
| Деталь: | Pressure Solenoid Assy |
| Парткод: | 023-75153-109 |
| Деталь: | BASE BRACKET, PRESSURE SOLENOID |
| Парткод: | 023-15020-100 |
| Деталь: | SOLENOID, TDS-10A-1056 |
| Парткод: | 490-50006-106 |
| Деталь: | LEVER, PRESSURE SOLENOID |
| Парткод: | 030-12114-205 |
| Деталь: | SPRING, PRESSURE SOLENOID |
| Парткод: | 023-15123-006 |
| Деталь: | LEVER ASSY, SEPARATOR |
| Парткод: | 023-15037-002 |
| Деталь: | SPRING, SEPARATOR |
| Парткод: | 023-15038-009 |
| Деталь: | None |
| Парткод: | SF51xxfflM Assy |
| Деталь: | CWTD3337G-24F-9K24D |
| Парткод: | 490-22024-204 |
| Деталь: | MAIN FLAME,DRUM |
| Парткод: | 023-75164-100 |
| Деталь: | FLANGE SUPPORT ROLLER, DRUM |
| Парткод: | 023-17116-007 |
| Деталь: | LOCK RING 4 |
| Парткод: | 023-17197-007 |
| Деталь: | S-GAP CAM |
| Парткод: | 024-17027-001 |
| Деталь: | FIXING PLATE, DRIVE SHAFT A3 |
| Парткод: | 023-17294-002 |
| Деталь: | FIXING PLATE DRIVE ,A4 |
| Парткод: | 023-17246-008 |
| Деталь: | STEPPED SCREW:F6X3,M4X4 |
| Парткод: | 635-00003-008 |
| Деталь: | CENTER SHAFT, DRUM |
| Парткод: | 023-17018-005 |
| Деталь: | GEAR,M1X45X6 |
| Парткод: | 612-10026-001 |
| Деталь: | BASE,INK BLOCKING PLATE(FRONT) |
| Парткод: | 023-17229-006 |
| Деталь: | INK BLOCKING PLATE, FRONT |
| Парткод: | 023-17227-003 |
| Деталь: | SHAFT SCREW, INK BLOCKING PLATE |
| Парткод: | 015-36317-305 |
| Деталь: | STEP SCREW,F4X3,M3X6 |
| Парткод: | 635-17433-103 |
| Деталь: | SPRING, INK BLOCKING PLATE |
| Парткод: | 015-36318-000 |
| Деталь: | BASE,INK BLOCKING PLATE(REAR) |
| Парткод: | 023-17228-000 |
| Деталь: | INK BLOCKING PLATE, REAR |
| Парткод: | 023-17226-007 |
| Деталь: | SPRING , DOCTOR ROLLER |
| Парткод: | 023-17333-008 |
| Деталь: | BRACKET, FRONT COVER SW |
| Парткод: | 023-34051-105 |
| Деталь: | MAGNET CATCH , SM50-P |
| Парткод: | 660-00002-004 |
| Деталь: | SENSOR, LG285D1 |
| Парткод: | 444-30010-007 |
| Деталь: | N/A |
| Парткод: | 059-34028-009 |
| Деталь: | BRACKET, USB COVER |
| Парткод: | 059-34036-001 |
| Деталь: | USB Cover |
| Парткод: | 059-34035-005 |
| Деталь: | WIRE HARNESS, POWER SW |
| Парткод: | 059-53027-005 |
| Деталь: | SB-6025 |
| Парткод: | 665-04055-001 |
| Деталь: | None |
| Парткод: | 059-53015-007 |
| Деталь: | WIRE HARNESS, USB |
| Парткод: | 059-53021-104 |
| Деталь: | PCB, USB-MEM |
| Парткод: | 058-50002-004 |
| Деталь: | N/A |
| Парткод: | 059-75085-009 |
| Деталь: | N/A |
| Парткод: | 059-75086-005 |
| Деталь: | N/A |
| Парткод: | 059-75087-001 |
| Деталь: | LEVER, MASTER ROLL HOLDER |
| Парткод: | 059-28011-005 |
| Деталь: | LEVER SPRING, MASTER ROLL HOLDER |
| Парткод: | 023-28135-003 |
| Деталь: | FULCRUM PLATE, MASTER ROLL HOLDER |
| Парткод: | 023-28130-001 |
| Деталь: | SHAFT, MASTER ROLL HOLDER |
| Парткод: | 023-28131-105 |
| Деталь: | LEVER SHAFT, MASTER ROLL HOLDER |
| Парткод: | 023-28132-101 |
| Деталь: | MASTER HOLDER BASE |
| Парткод: | 059-28010-009 |
| Деталь: | MASTER HOLDER BASE, B4 |
| Парткод: | 059-28021-000 |
| Деталь: | N/A |
| Парткод: | 059-28024-000 |
| Деталь: | HOOK, MASTER ROLL HOLDER |
| Парткод: | 023-28134-007 |
| Деталь: | REINFORCEMENT PLATE, MASTER HOLDER |
| Парткод: | 023-28394-009 |
| Деталь: | GUIDE SPRING, MASTER HOLDER |
| Парткод: | 023-28136-000 |
| Деталь: | DAMPER CASE, MASTER HOLDER |
| Парткод: | 023-28372-005 |
| Деталь: | MASTER FLANGE, REAR |
| Парткод: | 059-28009-000 |
| Деталь: | GUIDE FLANGE, MASTER HOLDER |
| Парткод: | 019-15255-007 |
| Деталь: | DAMPER, OG8G-C |
| Парткод: | 610-00024-006 |
| Деталь: | WRITE ROLLER ASSY II, A3 |
| Парткод: | 046-75016-009 |
| Деталь: | WRITE ROLLER ASSY II, B4 |
| Парткод: | 046-75017-005 |
| Деталь: | N/A |
| Парткод: | B4HLwrite roller assy |
| Деталь: | WRITE ROLLER, D23-A3 |
| Парткод: | 046-28011-007 |
| Деталь: | WRITE ROLLER, D23-B4 |
| Парткод: | 046-28020-006 |
| Деталь: | None |
| Парткод: | 059-28020-004 |
| Деталь: | LINER |
| Парткод: | 019-35025-008 |
| Деталь: | POWER SUPPLY, PS30-NWW |
| Парткод: | 059-50006-104 |
| Деталь: | POWER SUPPLY, PS28-NWW |
| Парткод: | 046-50529-109 |
| Деталь: | BRACKET UPPER, POWER SUPPLY |
| Парткод: | 046-50008-206 |
| Деталь: | BRACKET LOWER, POWER SUPPLY |
| Парткод: | 046-50009-300 |
| Деталь: | SET PLATE, SAFETY SW, REAR |
| Парткод: | 046-50010-006 |
| Деталь: | SHAFT BRACKET, DRIVE INTERLOCK SW |
| Парткод: | 023-50042-108 |
| Деталь: | SHAFT , DRIVE INTERLOCK SW |
| Парткод: | 042-50010-007 |
| Деталь: | DRIVE INTERLOCK SAFETY SW |
| Парткод: | 023-53026-103 |
| Деталь: | FRAME, DRIVE SAFETY SW |
| Парткод: | 046-50011-002 |
| Деталь: | HINGE UPPER, PCB BRACKET, EJECTION |
| Парткод: | 023-50001-002 |
| Деталь: | HINGE LOWER, PCB BRACKET, EJECTION |
| Парткод: | 023-50002-106 |
| Деталь: | SECURE BRACKET, REAR LOWER |
| Парткод: | 046-50007-005 |
| Деталь: | SECURE BRACKET, REAR UPPER |
| Парткод: | 046-50006-009 |
| Деталь: | SB-6025 |
| Парткод: | 665-04055-001 |
| Деталь: | SQUARE BUSHING , SB-4025 |
| Парткод: | 665-04002-005 |
| Деталь: | SQUARE BUSHING, SB-2718 |
| Парткод: | 665-04054-005 |
| Деталь: | EDGING SADDLE, EDS-17L |
| Парткод: | 665-02039-009 |
| Деталь: | JUNCTION WIRE HARNESS, M-MOTOR |
| Парткод: | 046-53011-003 |
| Деталь: | MAKING RELAY PCB |
| Парткод: | 059-50008-000 |
| Деталь: | xxx |
| Парткод: | 488-00048-101 |
| Деталь: | POWER CORD, 100V (L) |
| Парткод: | 488-00050-009 |
| Деталь: | POWER CORD, CH. |
| Парткод: | 488-00049-108 |
| Деталь: | Washer F4.5X12X1 |
| Парткод: | 023-50014-007 |
| Деталь: | SUB-SYSTEM-PCB, MODEL |
| Парткод: | 059-75004-009 |
| Деталь: | MAIN SYSTEMPCBI, S |
| Парткод: | 059-75001-000 |
| Деталь: | COVER BRACKET, SD |
| Парткод: | 059-50010-004 |
| Деталь: | M.-Making Junction PCB |
| Парткод: | 059-50008-008 |
| Деталь: | BRACKET UPPER, JUNCTION PCB, M.-M. |
| Парткод: | 023-28204-005 |
| Деталь: | BRACKET LOWER, JUNCTION PCB, M.-M. |
| Парткод: | 023-28221-007 |
| Деталь: | BRACKET, MAIN SYSTEM PCB |
| Парткод: | 059-50012-007 |
| Деталь: | WIRE HARNESS, MAIN SUB |
| Парткод: | 059-53003-009 |
| Деталь: | SIDE FRAME R, ELEVATOR |
| Парткод: | 023-12207-500 |
| Деталь: | SIDE FRANCE F, ELEVATOR |
| Парткод: | 023-12216-607 |
| Деталь: | ABSORBER GEAR LL, P.-F. |
| Парткод: | 023-12261-009 |
| Деталь: | ELEVATOR SHAFT ASSY,SU |
| Парткод: | 023-75159-107 |
| Деталь: | REINFORCEMENT PLATE, ELEVATOR |
| Парткод: | 023-12232-106 |
| Деталь: | ELEVATOR RACK, P.-F. |
| Парткод: | 023-12201-006 |
| Деталь: | LOWER LIMIT FRAME, P.-F. |
| Парткод: | 046-12216-008 |
| Деталь: | SUPPORT, LOWER LIMIT FRAME, P.-F. |
| Парткод: | 023-12206-008 |
| Деталь: | BRACKET R, SPRING, LOWER SAFETY SW |
| Парткод: | 023-12252-000 |
| Деталь: | SPRING, ELEVATOR SAFETY SW, LOWER |
| Парткод: | 023-12237-000 |
| Деталь: | Elevator Safety SW |
| Парткод: | 023-53023-104 |
| Деталь: | BRACKET, LOWER LIMIT SENSOR |
| Парткод: | 023-12233-307 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | SPRING, ELEVATOR |
| Парткод: | 023-12202-100 |
| Деталь: | BRACKET, ELEVATOR SPRING, P.-F. |
| Парткод: | 023-12203-009 |
| Деталь: | xxx |
| Парткод: | 046-12220-307 |
| Деталь: | BEARING,2F-FLAW678AZZ1/1K |
| Парткод: | 600-50057-006 |
| Деталь: | METALF8X13/12X5,16X2 |
| Парткод: | 651-00018-009 |
| Деталь: | Elevator Motor Assy |
| Парткод: | 023-75078-107 |
| Деталь: | COVER, ELEVATOR MOTOR |
| Парткод: | 023-12247-006 |
| Деталь: | MOTOR CHASSIS, ELEVATOR MOTOR |
| Парткод: | 023-12234-206 |
| Деталь: | GEAR COVER, ELEVATOR MOTOR |
| Парткод: | 023-12223-000 |
| Деталь: | xxx |
| Парткод: | 612-10009-107 |
| Деталь: | GEAR, M0.8X23+M0.8X14 |
| Парткод: | 612-80011-001 |
| Деталь: | GEAR, M0.8X30+M0.8X14 |
| Парткод: | 612-80012-008 |
| Деталь: | GEAR, M0.8X29+M1X14 |
| Парткод: | 612-80013-004 |
| Деталь: | ELEVATOR MOTOR COLLAR |
| Парткод: | 023-12244-104 |
| Деталь: | MOTOR ASSY (CWRS-445PA) |
| Парткод: | 023-75906-000 |
| Деталь: | SUPPORT, CLAMP WORM |
| Парткод: | 030-19205-001 |
| Деталь: | WIRE HARNESS, ELEVATOR MOTOR |
| Парткод: | 023-12602-108 |
| Деталь: | BRACKET, PAPER FEED JUNCTION PCB |
| Парткод: | 046-12201-000 |
| Деталь: | PFR-PCB |
| Парткод: | 059-50004-004 |
| Деталь: | JUNCTION WIRE HARNESS ,SAFETY SW,LL |
| Парткод: | 046-12708-105 |
| Деталь: | xxx |
| Парткод: | 059-53022-003 |
| Деталь: | BACK COVER, ELEVATOR MOTOR |
| Парткод: | 023-12248-002 |
| Деталь: | N/A |
| Парткод: | 059-75096-000 |
| Деталь: | N/A |
| Парткод: | 059-75097-007 |
| Деталь: | N/A |
| Парткод: | 059-75098-003 |
| Деталь: | N/A |
| Парткод: | SUnan88 |
| Деталь: | N/A |
| Парткод: | 059-21004-003 |
| Деталь: | SHAFT, BELT DRIVEN PULLEY |
| Парткод: | 023-21361-202 |
| Деталь: | FLAT BELT, 15X0.65X519 |
| Парткод: | 629-00002-004 |
| Деталь: | M WING FRONT |
| Парткод: | 023-21322-100 |
| Деталь: | S WING, FRONT |
| Парткод: | 023-21324-102 |
| Деталь: | SHAFT, WING FRONT |
| Парткод: | 023-21335-104 |
| Деталь: | SPRING, WING FRONT |
| Парткод: | 023-21328-108 |
| Деталь: | SPRING, WING REAR |
| Парткод: | 023-21332-202 |
| Деталь: | M WING REAR |
| Парткод: | 023-21321-103 |
| Деталь: | S WING, REAR |
| Парткод: | 023-21323-106 |
| Деталь: | SHAFT, WING REAR |
| Парткод: | 023-21325-109 |
| Деталь: | ROLLER PLATE, TRANSFER BELT |
| Парткод: | 023-21371-100 |
| Деталь: | BELT ROLLER, SUCTION |
| Парткод: | 017-13216-000 |
| Деталь: | LINK PLATE, S WING |
| Парткод: | 023-21329-104 |
| Деталь: | LINK PLATE, M WING |
| Парткод: | 023-21331-001 |
| Деталь: | METAL, F6X10/9X4, 12X1.5 |
| Парткод: | 651-00017-002 |
| Деталь: | BEARING, DDLF-1060ZZH |
| Парткод: | 600-05101-002 |
| Деталь: | 6100.9P SPACER |
| Парткод: | 639-00001-004 |
| Деталь: | xxx |
| Парткод: | 023-21351-207 |
| Деталь: | ROLLER (INNER), TRANSFER BELT |
| Парткод: | 030-15249-004 |
| Деталь: | PULLEY, P40S2M60 |
| Парткод: | 611-90002-003 |
| Деталь: | BELT, 40-S2M-138 |
| Парткод: | 621-00031-006 |
| Деталь: | BRACKET, PAPER RECEIVING SENSOR |
| Парткод: | 023-21401-000 |
| Деталь: | SENSOR, GP2A210LCSJF |
| Парткод: | 444-33012-000 |
| Деталь: | WIRE HARNESS, EJECTION SENSOR |
| Парткод: | 023-21703-006 |
| Деталь: | FACE COVER, SUCTION |
| Парткод: | 023-21304-004 |
| Деталь: | FACE COVER, SUCTION C |
| Парткод: | 023-21414-004 |
| Деталь: | SUCTION BOX, SUCTION |
| Парткод: | 023-21302-109 |
| Деталь: | SUCTION MOTOR, CCWRS-55PH |
| Парткод: | 023-75907-006 |
| Деталь: | METAL SLIT, MOTOR |
| Парткод: | 023-21342-305 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | FAN, E1033H24BYAZ-33 |
| Парткод: | 490-41014-104 |
| Деталь: | BASE FRAME, SUCTION |
| Парткод: | 046-21301-000 |
| Деталь: | N/A |
| Парткод: | 059-53028-001 |
| Деталь: | N/A |
| Парткод: | 059-53029-008 |
| Деталь: | BOSS, WING CAM SHAFT |
| Парткод: | 023-21406-001 |
| Деталь: | W CAM SHAFT, WING |
| Парткод: | 023-21410-009 |
| Деталь: | MW CAM, WING |
| Парткод: | 023-21408-004 |
| Деталь: | HELICAL GEAR, M1X16X6 |
| Парткод: | 612-30001-005 |
| Деталь: | SW CAM, WING |
| Парткод: | 023-21409-108 |
| Деталь: | xxx |
| Парткод: | 023-21404-106 |
| Деталь: | MOTOR, PM42L-048-ZVS6 |
| Парткод: | 490-33015-100 |
| Деталь: | WORM GEAR, M1X12X1 |
| Парткод: | 612-50005-007 |
| Деталь: | W DRIVE SHAFT, WING MOTOR |
| Парткод: | 023-21411-102 |
| Деталь: | GEAR, M0.5X21X6 |
| Парткод: | 612-10035-000 |
| Деталь: | SUPPORT PLATE, SUCTION |
| Парткод: | 046-21302-006 |
| Деталь: | BRACKET, FIX WING |
| Парткод: | 046-21311-005 |
| Деталь: | FIX WING, F |
| Парткод: | 023-21334-108 |
| Деталь: | FIX WING, R |
| Парткод: | 023-21333-101 |
| Деталь: | COVER, PAPER-RECEIVING FG SENSOR |
| Парткод: | 023-21412-001 |
| Деталь: | DE-ELECTRICITY BRUSH, 180 |
| Парткод: | 045-21316-000 |
| Деталь: | SEAL, FOLDING TRAY INST., P.-RCV.-T |
| Парткод: | 023-21801-008 |
| Деталь: | Fixing Pin |
| Парткод: | 020-13114-300 |
| Деталь: | MOUNT BRACKET FRONT, SUCTION UNIT |
| Парткод: | 023-21391-101 |
| Деталь: | MOUNT BRACKET REAR, SUCTION UNIT |
| Парткод: | 023-21392-108 |
| Деталь: | COVER PLATE, SUCTION |
| Парткод: | 023-21381-300 |
| Деталь: | SHIELD PLATE, KNOB, SUCTION |
| Парткод: | 023-21384-008 |
| Деталь: | WING CAM, SUCTION |
| Парткод: | 023-21382-005 |
| Деталь: | WING KNOB, SUCTION |
| Парткод: | 023-21383-001 |
| Деталь: | SUPPORT, WING KNOB, SUCTION |
| Парткод: | 023-21385-101 |
| Деталь: | WIRE HARNESS, PAPER EJECTION CONTROL |
| Парткод: | 059-53006-008 |
| Деталь: | WIRE HARNESS |
| Парткод: | 059-53004-005 |
| Деталь: | SEAL, JUMP WING INST, METRIC |
| Парткод: | 023-21806-000 |
| Деталь: | SEAL, JUMP WING INST, INCH |
| Парткод: | 023-21807-006 |
| Деталь: | None |
| Парткод: | 059-21001-004 |
| Деталь: | BS SNS CABLE-L |
| Парткод: | 059-75025-006 |
| Деталь: | BS MOTOR CABLE |
| Парткод: | 059-75026-002 |
| Деталь: | SHEET DUST18SNS |
| Парткод: | 059-75027-009 |
| Деталь: | SHEET PROTECT FFC |
| Парткод: | 059-75028-005 |
| Деталь: | GFPC-31-12 |
| Парткод: | 059-75029-001 |
| Деталь: | SLIDER |
| Парткод: | 059-75030-000 |
| Деталь: | SUPPORT BRACKET, FB SCANNER |
| Парткод: | 023-10015-000 |
| Деталь: | RUBBER FOOT |
| Парткод: | 660-01015-002 |
| Деталь: | NOISE ABSORBER, BOTTOM, MAIN FRAME |
| Парткод: | 023-10024-000 |
| Деталь: | Transportation Support Plate |
| Парткод: | 023-10008-004 |
| Деталь: | Lifting Handle |
| Парткод: | 023-10017-305 |
| Деталь: | STOPPER, LIFTING HANDLE |
| Парткод: | 023-10030-000 |
| Деталь: | COVER, GUIDE ROLLER |
| Парткод: | 046-12506-006 |
| Деталь: | NOISE ABSORBER, GUIDE ROLLER COVER |
| Парткод: | 023-12544-108 |
| Деталь: | LOWER COVER, GUIDE PLATE |
| Парткод: | 023-12541-001 |
| Деталь: | STAY, GUIDE PLATE |
| Парткод: | 023-12536-105 |
| Деталь: | STOPPER, M.-M. UNIT |
| Парткод: | 023-28358-002 |
| Деталь: | PROTECTION PLATE, WIRE HARNESS, M.- |
| Парткод: | 023-28408-000 |
| Деталь: | SUPPORT PLATE FRONT, P.-RCV.-T. |
| Парткод: | 023-21641-507 |
| Деталь: | SUPPORT PLATE REAR, P.-RCV.-T. |
| Парткод: | 023-21642-503 |
| Деталь: | MAGNET CATCH, P.-RCV.-T. |
| Парткод: | 023-21622-006 |
| Деталь: | EDGING SADDLE,EDS-17L |
| Парткод: | 665-02039-009 |
| Деталь: | N/A |
| Парткод: | 059-75103-007 |
| Деталь: | BASE BRACKET, PRESSURE CONTROL |
| Парткод: | 023-15023-109 |
| Деталь: | COVER PLATE, PRESSURE CONTROL |
| Парткод: | 023-15027-007 |
| Деталь: | WORM GEAR, PRESSURE CONTROL |
| Парткод: | 023-15030-008 |
| Деталь: | WORM SHAFT, PRESSURE CONTROL |
| Парткод: | 023-15029-107 |
| Деталь: | GEAR, PRESSURE CONTROL |
| Парткод: | 023-15028-003 |
| Деталь: | GEAR SHAFT, PRESSURE CONTROL |
| Парткод: | 023-15025-101 |
| Деталь: | MOTOR, STP-43D2054 |
| Парткод: | 490-31016-206 |
| Деталь: | SENSOR, LG-248NL1 |
| Парткод: | 444-30008-100 |
| Деталь: | BRACKET, HP SENSOR, PRESSURE CONTRO |
| Парткод: | 023-15032-000 |
| Деталь: | GEAR WHEEL, PRESSURE CONTROL |
| Парткод: | 023-15031-101 |
| Деталь: | ROTATION PLATE, PRESSURE CONTROL |
| Парткод: | 059-15009-001 |
| Деталь: | WIRE HARNESS, PAPER EJECTION REAR |
| Парткод: | 059-53004-005 |
| Деталь: | PRESSURE SPRING, H25 |
| Парткод: | 045-15018-200 |
| Деталь: | NOISE REDUCTION, PRESSURE SPRING |
| Парткод: | 059-15002-007 |
| Деталь: | BRACKET BASE, GUIDE ROLLER SHAFT |
| Парткод: | 023-15062-007 |
| Деталь: | BASE BRACKET, GUIDE ROLLER RELEASE |
| Парткод: | 023-15154-408 |
| Деталь: | SPRING, GUIDE ROLLER RELEASE |
| Парткод: | 023-15063-208 |
| Деталь: | Guide Roller Lever |
| Парткод: | 023-15061-000 |
| Деталь: | LEVER PLATE, SECTOR GEAR |
| Парткод: | 023-15058-301 |
| Деталь: | Sector Gear |
| Парткод: | 023-15059-006 |
| Деталь: | xxx |
| Парткод: | 023-15060-306 |
| Деталь: | HOOK BRACKET, SPRING, SECTOR GEAR |
| Парткод: | 023-15155-200 |
| Деталь: | BRACKET, 1ST TRANSMISSION |
| Парткод: | 023-15041-409 |
| Деталь: | GEAR,M1X41+M1X29 |
| Парткод: | 612-82407-107 |
| Деталь: | GEAR, M1X28X8 |
| Парткод: | 612-12208-107 |
| Деталь: | JUNCTION WIRE HARNESS ,SAFETY SW,LL |
| Парткод: | 046-12708-105 |
Коды ошибок
A01 201
A01 202
A01 211
A01 214
A01 215
A01 258
A02 509
A04 303
A05 304
A05 312
A05 315
A06 403
A07 409
A07 412
A07 413
A07 418
A07 429
A07 432
A08 410
A08 430
A09 411
A09 417
A09 431
A10 189
A10 190
A10 191
A10 193
A10 194
A10 195
A10 196
A10 198
A16 525
A17 209
A34 218
B01 730
B21 714
B21 715
B21 716
B22 721
B22 727
B23 722
B23 723
B24 724
B24 725
B24 726
B29 926
B30 910
B31 916
B32 914
B32 915
B32 917
B33 931
B34 919
B35 970
B36 733
B37 734
B38 911
B39 999
B40 47
C01 512
C01 563
C01 574
C02 200
C02 240
C02 253
C03 308
C03 311
C04 402
C11 590
C12 266
C13 268
D01 526
D01 527
D01 528
D01 529
D01 530
D02 532
D02 580
D03 533
D04 534
D04 560
D04 561
D04 562
D04 564
D04 575
D05 210
D07 310
D08 224
D08 226
D08 227
D08 228
D09 212
D11 535
D13 9
D17 236
D17 237
D17 238
D17 239
D17 241
D17 256
D18 522
D19 223
D22 531
D22 540
D22 542
D23 177
D50 165
E01 10
E02 11
E02 12
E02 22
F01
F02 18
F03 16
F04 905
F04 906
F05 19
F10 21
F17 27
F24 37
F28 435
F32 713
F33 913
F34 835
F37 50
F38 43
F39 44
F43 902
F44 901
F45 959
F45 981
F47 904
F48 955
F51 548
F52 912
F56 265
F57 267
F58 927
F60 929
F62 956
F64 964
F65 965
F73 975
F74 980
F78 731
F79 732
F85 997
F85 998
F90 957
F91 958
F94 7
F95 8
F96 918
F97 928
H01 566
H02 567
H03 568
H04 242
H05 243
H06 244
H08 578
H09 579
H10 263
H11 264
T01 520
T01 521
T01 524
T01 537
T01 538
T01 582
T02 400
T02 401
T02 404
T02 405
T02 406
T02 407
T02 408
T02 434
T03 500
T03 501
T03 502
T03 503
T03 504
T03 505
T03 506
T03 507
T03 508
T03 545
T04 513
T05 603
T05 604
T05 605
T05 612
T05 619
T05 632
T09 720
T11 600
T11 601
T11 602
T11 614
T11 631
T12 301
T12 302
T12 305
T12 306
T12 307
T12 309
T12 316
T13 203
T13 204
T13 205
T13 221
T13 222
T13 231
T13 232
T13 233
T13 234
T14 114
T14 115
T14 116
T14 117
T14 123
T14 124
T14 125
T14 126
T14 135
T14 136
T14 137
T14 138
T14 170
T15 130
T15 131
T15 132
T15 133
T15 134
T15 151
T15 152
T15 153
T15 155
T15 157
T15 158
T15 161
T15 199
T19 207
T19 208
T19 216
T19 217
T20 416
T20 437
T20 442
T20 456
T24 539
T25 26
T90 1003
T90 1006
T90 1007
T90 1008
T90 1009
T90 1010
T90 1011
T90 1012
T90 1013
T90 1014
T90 1015
T90 1016
T90 1017
T90 1018
T90 1019
T90 1020
T90 1021
T90 1022
T90 1023
T90 1024
T90 1025
T90 1026
T90 1027
T91 13
T92 570
T93 932
T93 933
T94 225
T96 171
T96 172
T96 433
T96 569
T96 613
T96 972
T97 939
T97 941
T97 942
T97 943
T97 944
T97 945
T97 946
T97 990
T97 991
T97 992
T97 993
T97 994
T98 1005
T98 119
T98 129
T98 2
T98 245
T98 246
T98 25
T98 28
T98 29
T98 34
T98 35
T98 39
T98 422
T98 423
T98 5
T98 53
T98 54
T98 6
T98 63
T98 735
T98 736
T98 777
T98 778
T98 787
T98 788
T98 789
T98 790
T98 791
T98 792
T98 921
T98 934
T98 935
T98 937
T98 938
T98 947
T98 948
T98 949
T98 950
T98 952
T98 953
T98 960
T98 961
T98 97
T98 978
T98 979
T98 98
T98 983
T98 984
T99 1031
T99 1032
T99 1303
T99 14
T99 150
T99 154
T99 156
T99 159
T99 181
T99 185
T99 186
T99 187
T99 188
T99 3001
T99 64
T99 65
T99 67
T99 68
T99 69
T99 70
T99 7028
T99 71
T99 75
T99 76
T99 77
T99 78
T99 79
T99 80
T99 81
T99 82
T99 923
T99 924
Описание
| Error code: | A01 201 |
| Description: | • Master positioning is not correct. |
| Causes: | Master positioning sensor is not turned ON at master setting/cutting or at master making even after master has been transferred. |
| Remedy: | Master making unit upper cover set switch: OFF -> ON, and Master positioning sensor: OFF (Reset the master to cancel the error.) |
| Error code: | A01 202 |
| Description: | • Master positioning is not correct. |
| Causes: | Master positioning sensor is not turned OFF at master setting operation or at the start of master making even if the master roll is rewound for the set period of time. |
| Remedy: | Master making unit upper cover set switch: OFF -> ON, and Master positioning sensor: OFF (Reset the master to cancel the error.) |
| Error code: | A01 211 |
| Description: | • Master positioning is not correct. |
| Causes: | Master positioning sensor is ON in standby mode. |
| Remedy: | Master making unit upper cover set switch: OFF -> ON, and Master positioning sensor: OFF (Reset the master to cancel the error.) |
| Error code: | A01 214 |
| Description: | • Master positioning is not correct. |
| Causes: | The Master positioning sensor is ON at the start of master making operation. |
| Remedy: | Master making unit upper cover set switch: OFF -> ON, and Master positioning sensor: OFF (Reset the master to cancel the error.) |
| Error code: | A01 215 |
| Description: | • Master positioning is not correct. |
| Causes: | The logical value of the sensor at the destination differ from the theoretical value even after the writing PM operation ended due to the sensor stop mode. |
| Remedy: | Master making unit upper cover set switch: OFF -> ON, and Master positioning sensor: OFF (Reset the master to cancel the error.) |
| Error code: | A01 258 |
| Description: | • Master positioning is not correct. |
| Causes: | The Master end sensor is turned OFF after the master end seal has been detected, and the Master end sensor responses again while the master end is being confirmed. |
| Remedy: | Master making unit upper cover set switch: OFF -> ON, and Master positioning sensor: OFF (Reset the master to cancel the error.) |
| Error code: | A02 509 |
| Description: | • Master loading has failed. |
| Causes: | The Master loading sensor has been OFF when the master detection check at the specified angle is performed during master loading operation. |
| Remedy: | Print drum connection signal: ON -> OFF, and Print drum set switch: ON -> OFF (Pull out the print drum to cancel the error.) -> Perform the recovery operation. * If this error occurs, print drum lock is automatically released. (Only when the print drum is at position-B.) |
| Error code: | A04 303 |
| Description: | • Master removal has failed (when the master is on the print drum). |
| Causes: | Print drum check when a master removal error or master disposal jam occurs |
| Remedy: | Print drum connection signal: ON -> OFF, and Print drum set switch: ON -> OFF Pull out the print drum to cancel the error. * If this error occurs, print drum lock is automatically released. (Only when the print drum is at position-B.) |
| Error code: | A05 304 |
| Description: | • Master removal has failed. • Master removal has failed (when the master is at the master removal section). |
| Causes: | Master disposal box check when a master removal error or master disposal jam occurs |
| Remedy: | Master disposal box set switch: OFF, and Master removal sensor: OFF (The error is canceled if the disposed master has been removed when the Master disposal box is pulled out.) |
| Error code: | A05 312 |
| Description: | • Master removal has failed. • Master removal has failed (when the master is at the master removal section). |
| Causes: | The Master disposal jam sensor is ON at the start of the master making operation. |
| Remedy: | Master disposal box set switch: OFF, and Master removal sensor: OFF (The error is canceled if the disposed master has been removed when the Master disposal box is pulled out.) |
| Error code: | A05 315 |
| Description: | • Master removal has failed. • Master removal has failed (when the master is at the master removal section). |
| Causes: | The Master disposal jam sensor is ON at the end of the recovery operation. |
| Remedy: | Master disposal box set switch: OFF, and Master removal sensor: OFF (The error is canceled if the disposed master has been removed when the Master disposal box is pulled out.) |
| Error code: | A06 403 |
| Description: | • Paper feed tray is at the upper limit position or lower limit position. |
| Causes: | Paper feed tray set switch is OFF. * Not detected while in the low power mode (24V OFF). |
| Remedy: | Paper feed tray upper limit set switch: ON or • Paper feed tray lower limit set switch: ON |
| Error code: | A07 409 |
| Description: | • Paper feed has failed (or no paper has been fed). |
| Causes: | Paper ejection sensor is OFF at the time when the paper reaches the Paper ejection sensor, and the Paper sensor is ON at the time it stops. (Paper feed error) |
| Remedy: | Turn OFF the Paper sensor, and press the <RESET> key or [Confirm] button. |
| Error code: | A07 412 |
| Description: | • Paper feed has failed (or no paper has been fed). |
| Causes: | Paper sensor has been OFF N times consecutively at the time of first paper feed jam detection. (No-paper feed error) |
| Remedy: | Turn OFF the Paper sensor, and press the <RESET> key or [Confirm] button. |
| Error code: | A07 413 |
| Description: | • Paper feed has failed (or no paper has been fed). |
| Causes: | Paper sensor is ON at the time when the paper gets out of the Paper sensor. (Possible extra-long paper error.) |
| Remedy: | Turn OFF the Paper sensor, and press the <RESET> key or [Confirm] button. |
| Error code: | A07 418 |
| Description: | • Paper feed has failed (or no paper has been fed). |
| Causes: | The Paper sensor is ON at the start of the operation (note 1). |
| Remedy: | Turn OFF the Paper sensor, and press the <RESET> key or [Confirm] button. |
| Error code: | A07 429 |
| Description: | • Paper feed has failed (or no paper has been fed). |
| Causes: | Paper feed error (for recovery) |
| Remedy: | Turn OFF the Paper sensor, and press the <RESET> key or [Confirm] button. |
| Error code: | A07 432 |
| Description: | • Paper feed has failed (or no paper has been fed). |
| Causes: | The Paper sensor has already been ON when the paper feed is retried due to no paper feed. |
| Remedy: | Turn OFF the Paper sensor, and press the <RESET> key or [Confirm] button. |
| Error code: | A08 410 |
| Description: | • Paper ejection has failed. (Paper ejection sensor is OFF at the time when it must be ON.) (Paper is stuck on the print drum.) |
| Causes: | Paper ejection sensor is OFF at the time when the paper reaches the Paper ejection sensor, and the Paper sensor is OFF at the time it stops. (Paper jam on print drum) |
| Remedy: | Print drum connection signal: ON -> OFF, and Print drum set switch: ON -> OFF Pull out the print drum to cancel the error. * If this error occurs, print drum lock is automatically released. (Only when the print drum is at position-B.) |
| Error code: | A08 430 |
| Description: | • Paper ejection has failed. (Paper ejection sensor is OFF at the time when it must be ON.) (Paper is stuck on the print drum.) |
| Causes: | Paper jam on print drum (for recovery) |
| Remedy: | Print drum connection signal: ON -> OFF, and Print drum set switch: ON -> OFF Pull out the print drum to cancel the error. * If this error occurs, print drum lock is automatically released. (Only when the print drum is at position-B.) |
| Error code: | A09 411 |
| Description: | • Paper ejection has failed. (Paper ejection sensor is ON at the time when it must be OFF.) |
| Causes: | Paper ejection sensor is ON at the time when the paper gets out of the Paper ejection sensor. |
| Remedy: | Turn OFF the Paper ejection sensor, and press the <RESET> key or [Confirm] button. |
| Error code: | A09 417 |
| Description: | • Paper ejection has failed. (Paper ejection sensor is ON at the time when it must be OFF.) |
| Causes: | The Paper ejection sensor is ON at the start of the operation (note 1). |
| Remedy: | Turn OFF the Paper ejection sensor, and press the <RESET> key or [Confirm] button. |
| Error code: | A09 431 |
| Description: | • Paper ejection has failed. (Paper ejection sensor is ON at the time when it must be OFF.) |
| Causes: | Paper ejection error (for recovery) |
| Remedy: | Turn OFF the Paper ejection sensor, and press the <RESET> key or [Confirm] button. |
| Error code: | A10 189 |
| Description: | • AF original transport has failed (original pulled out, retained, or not transported, AF paper feed cover open during original transportation, lack of paper interval) |
| Causes: | AF paper feed section jam At original transport in AF, the running sensor is not turned ON after a lapse of the specified period of time since the Paper feed clutch has been turned ON. * Error detection at AF side |
| Remedy: | Simplex AF: Turn OFF the AF original detection sensor, AF original registration sensor, AF original IN sensor, and AF original ejection sensor, and press the [Confirm] button. Duplex AF: Turn OFF the AF original detection sensor, AF end detection sensor, AF original registration sensor, AF switchback sensor, and AF original ejection sensor, and turn ON the AF paper feed cover open/close sensor. (Set the AF paper feed cover again to release.) |
| Error code: | A10 190 |
| Description: | • AF original transport has failed (original pulled out, retained, or not transported, AF paper feed cover open during original transportation, lack of paper interval) |
| Causes: | AF original transport section jam 1 At original transport in AF, the edge sensor is not turned ON after a lapse of the specified period of time since the Registration clutch has been turned ON. * Error detection at AF side |
| Remedy: | Simplex AF: Turn OFF the AF original detection sensor, AF original registration sensor, AF original IN sensor, and AF original ejection sensor, and press the [Confirm] button. Duplex AF: Turn OFF the AF original detection sensor, AF end detection sensor, AF original registration sensor, AF switchback sensor, and AF original ejection sensor, and turn ON the AF paper feed cover open/close sensor. (Set the AF paper feed cover again to release.) |
| Error code: | A10 191 |
| Description: | • AF original transport has failed (original pulled out, retained, or not transported, AF paper feed cover open during original transportation, lack of paper interval) |
| Causes: | AF paper jam in switchback section At original transport in AF, the running sensor is not turned ON after a lapse of the specified period of time since the switchback clutch has been turned ON. * Error detection at AF side |
| Remedy: | Simplex AF: Turn OFF the AF original detection sensor, AF original registration sensor, AF original IN sensor, and AF original ejection sensor, and press the [Confirm] button. Duplex AF: Turn OFF the AF original detection sensor, AF end detection sensor, AF original registration sensor, AF switchback sensor, and AF original ejection sensor, and turn ON the AF paper feed cover open/close sensor. (Set the AF paper feed cover again to release.) |
| Error code: | A10 193 |
| Description: | • AF original transport has failed (original pulled out, retained, or not transported, AF paper feed cover open during original transportation, lack of paper interval) |
| Causes: | AF original transport section jam 3 At original transport in AF, the edge sensor is not turned OFF after a lapse of the specified period of time since the running sensor has been turned OFF. * Error detection at AF side |
| Remedy: | Simplex AF: Turn OFF the AF original detection sensor, AF original registration sensor, AF original IN sensor, and AF original ejection sensor, and press the [Confirm] button. Duplex AF: Turn OFF the AF original detection sensor, AF end detection sensor, AF original registration sensor, AF switchback sensor, and AF original ejection sensor, and turn ON the AF paper feed cover open/close sensor. (Set the AF paper feed cover again to release.) |
| Error code: | A10 194 |
| Description: | • AF original transport has failed (original pulled out, retained, or not transported, AF paper feed cover open during original transportation, lack of paper interval) |
| Causes: | AF original transport section jam 4 At original transport in AF, the jam sensor is not turned ON after a lapse of the specified period of time since the edge sensor has been turned ON. * Error detection at AF side |
| Remedy: | Simplex AF: Turn OFF the AF original detection sensor, AF original registration sensor, AF original IN sensor, and AF original ejection sensor, and press the [Confirm] button. Duplex AF: Turn OFF the AF original detection sensor, AF end detection sensor, AF original registration sensor, AF switchback sensor, and AF original ejection sensor, and turn ON the AF paper feed cover open/close sensor. (Set the AF paper feed cover again to release.) |
| Error code: | A10 195 |
| Description: | • AF original transport has failed (original pulled out, retained, or not transported, AF paper feed cover open during original transportation, lack of paper interval) |
| Causes: | AF paper jam in paper ejection unit At original transport in AF, the jam sensor is not turned OFF after a lapse of the specified period of time since the edge sensor has been turned OFF. * Error detection at AF side |
| Remedy: | Simplex AF: Turn OFF the AF original detection sensor, AF original registration sensor, AF original IN sensor, and AF original ejection sensor, and press the [Confirm] button. Duplex AF: Turn OFF the AF original detection sensor, AF end detection sensor, AF original registration sensor, AF switchback sensor, and AF original ejection sensor, and turn ON the AF paper feed cover open/close sensor. (Set the AF paper feed cover again to release.) |
| Error code: | A10 196 |
| Description: | • AF original transport has failed (original pulled out, retained, or not transported, AF paper feed cover open during original transportation, lack of paper interval) |
| Causes: | AF scanning section jam (extra-long paper) At original transport in AF, the edge sensor is not turned OFF after a lapse of the specified period of time since the edge sensor has been turned ON (due to original paper that is too long). * Error detection at AF side |
| Remedy: | Simplex AF: Turn OFF the AF original detection sensor, AF original registration sensor, AF original IN sensor, and AF original ejection sensor, and press the [Confirm] button. Duplex AF: Turn OFF the AF original detection sensor, AF end detection sensor, AF original registration sensor, AF switchback sensor, and AF original ejection sensor, and turn ON the AF paper feed cover open/close sensor. (Set the AF paper feed cover again to release.) |
| Error code: | A10 198 |
| Description: | • AF original transport has failed (original pulled out, retained, or not transported, AF paper feed cover open during original transportation, lack of paper interval) |
| Causes: | AF paper remaining jam Any of the running sensor, edge sensor, or jam sensor is ON at the start of AF operation. * Error detection at AF side |
| Remedy: | Simplex AF: Turn OFF the AF original detection sensor, AF original registration sensor, AF original IN sensor, and AF original ejection sensor, and press the [Confirm] button. Duplex AF: Turn OFF the AF original detection sensor, AF end detection sensor, AF original registration sensor, AF switchback sensor, and AF original ejection sensor, and turn ON the AF paper feed cover open/close sensor. (Set the AF paper feed cover again to release. |
| Error code: | A16 525 |
| Description: | • The master remains on the print drum. |
| Causes: | Awaiting removal of master from print drum. |
| Remedy: | Print drum connection signal: ON -> OFF, and Print drum set switch: ON -> OFF Pull out the print drum to cancel the error. * If this error occurs, print drum lock is automatically released. (Only when the print drum is at position-B.) |
| Error code: | A17 209 |
| Description: | • Cutter positioning is not correct. |
| Causes: | The Cutter HP switch is OFF when the machine has gone into standby, at the start of master making operation, or when the master is set. |
| Remedy: | Master making unit upper cover set switch: OFF -> ON, and Master detection sensor: OFF (Close the master making unit cover without setting master to cancel the error.) -> Error canceling operation (The cutter returns to the home position.) |
| Error code: | A34 218 |
| Description: | • Master is not set properly. |
| Causes: | Master reset command |
| Remedy: | Master making unit upper cover set switch: OFF -> ON, and Master positioning sensor: OFF (Reset the master to cancel the error.) |
| Error code: | B01 730 |
| Description: | • No card is inserted in the Card counter. |
| Causes: | Card counter: No card |
| Remedy: | Insert the card. |
| Error code: | B21 714 |
| Description: | • Reading from/writing to the storage memory failed. |
| Causes: | File name error of the storage memory. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | B21 715 |
| Description: | • Reading from/writing to the storage memory failed. |
| Causes: | Storage memory access error. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | B21 716 |
| Description: | • Reading from/writing to the storage memory failed. |
| Causes: | Other storage memory errors. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | B22 721 |
| Description: | • Job separator is powered OFF. |
| Causes: | The power is OFF when the <START> key is pressed while the function settings “Job Separation” is set to ON. |
| Remedy: | • Touch the [Confirm] button. • Press the <RESET> key. |
| Error code: | B22 727 |
| Description: | • Job separator is powered OFF. |
| Causes: | After a lapse of seven seconds since the cluster A signal has been turned ON, the busy signal remains in the L status (the power is turned OFF during job separation tape output). |
| Remedy: | • Touch the [Confirm] button. • Press the <RESET> key. |
| Error code: | B23 722 |
| Description: | • The tape in the job separator has run out. |
| Causes: | When the busy signal status is H (power ON), if the <START> key is pressed while the function settings “Job Separation” is set to ON, the tape detection signal indicates H (no tape) status. |
| Remedy: | • Touch the [Confirm] button. • Press the <RESET> key. |
| Error code: | B23 723 |
| Description: | • The tape in the job separator has run out. |
| Causes: | After the tape output command has been issued, the busy signal status changes from L to H (operation completed), and the tape detection signal indicates H (no tape) status. |
| Remedy: | • Touch the [Confirm] button. • Press the <RESET> key. |
| Error code: | B24 724 |
| Description: | • Tape jam occurred on the job separator. |
| Causes: | When the busy signal status is H (power ON), if the <START> key is pressed while the function settings “Job Separation” is set to ON, the tape jam detection signal indicates L (tape remaining) status. |
| Remedy: | • Touch the [Confirm] button. • Press the <RESET> key. |
| Error code: | B24 725 |
| Description: | • Tape jam occurred on the job separator. |
| Causes: | Tape jam detection signal indicates H (tape transport error) status after a lapse of 1200 ms. since the cluster A signal has been turned ON. |
| Remedy: | • Touch the [Confirm] button. • Press the <RESET> key. |
| Error code: | B24 726 |
| Description: | • Tape jam occurred on the job separator. |
| Causes: | After the cluster A signal has been turned ON, at the time when the busy signal status changes from L to H (or after a lapse of seven seconds while it remains in the L status), the tape jam detection signal indicates L (tape ejection error) status. |
| Remedy: | • Touch the [Confirm] button. • Press the <RESET> key. |
| Error code: | B29 926 |
| Description: | • USB hub has been connected. |
| Causes: | USB hub has been connected. |
| Remedy: | • Touch the [Close] button. • Press the <RESET> key. • Disconnect the USB device. |
| Error code: | B30 910 |
| Description: | • Incompatible USB device is connected. |
| Causes: | An incompatible USB device has been set. |
| Remedy: | • Touch the [Close] button. • Press the <RESET> key. • Disconnect the USB device. |
| Error code: | B31 916 |
| Description: | • Network cable is not connected. |
| Causes: | The network cable is not connected at startup. |
| Remedy: | The error display can be cleared by any of the following: • Touch the [Close] button. • Press the <RESET> key. |
| Error code: | B32 914 |
| Description: | • Communication with external device failed. |
| Causes: | MIB information request error Transmission not performed in three seconds (WAK)/No response from the destination/ Destination disconnected/TCP/IP of NET-D not functioning/Undefined interruption received from the machine, etc. |
| Remedy: | The error display can be cleared by any of the following: • Press the <RESET> key or [Close] button. • Press the [Link Switch] button, if displayed, to switch the link. (Clear the printer error to cancel the error.) |
| Error code: | B32 915 |
| Description: | • Communication with external device failed. |
| Causes: | No MIB information replied NET-D (destination of communication) does not respond in 50 seconds. |
| Remedy: | The error display can be cleared by any of the following: • Press the <RESET> key or [Close] button. • Press the [Link Switch] button, if displayed, to switch the link. (Clear the printer error to cancel the error.) |
| Error code: | B32 917 |
| Description: | • Communication with external device failed. |
| Causes: | Communication error occurred on network. |
| Remedy: | The error display can be cleared by any of the following: • Press the <RESET> key or [Close] button. • Press the [Link Switch] button, if displayed, to switch the link. (Clear the printer error to cancel the error.) |
| Error code: | B33 931 |
| Description: | • IP address is not set. |
| Causes: | IP address is not set. |
| Remedy: | The error display can be cleared by any of the following: • Touch the [Close] button. • Press the <RESET> key. |
| Error code: | B34 919 |
| Description: | • Toner of RLP has run out. |
| Causes: | Toner of Prioa has run out. |
| Remedy: | The error display can be cleared by any of the following: • Touch the [Close] button. • Press the [Link Switch] button, if displayed, to switch the link. |
| Error code: | B35 970 |
| Description: | • Serviceman-call error occurred on RLP. |
| Causes: | Service error has occurred on Prioa. |
| Remedy: | The error display can be cleared by any of the following: • Touch the [Close] button. • Press the <RESET> key. • Press the [Link Switch] button, if displayed, to switch the link. |
| Error code: | B36 733 |
| Description: | • The amount of coins for the coin vendor is insufficient. |
| Causes: | The amount of coins for the coin vendor is insufficient. |
| Remedy: | Insert coins until the amount reaches the sufficient amount for the machine to operate. |
| Error code: | B37 734 |
| Description: | • No card is inserted into the card vendor. • The remaining amount in the card is insufficient to use the card vendor. |
| Causes: | Card vendor: No card is inserted or remaining amount in the card is insufficient. |
| Remedy: | Insert the card that has sufficient remaining amount. |
| Error code: | B38 911 |
| Description: | RISO folder creation in the USB memory failed. |
| Causes: | RISO folder creation has failed. |
| Remedy: | • Touch the [Close] button. • Press the <RESET> key. • Disconnect the USB device. |
| Error code: | B39 999 |
| Description: | • Error detected on USB file system |
| Causes: | An error has been detected on the USB file system. |
| Remedy: | • Touch the [Close] button. • Press the <RESET> key. • Disconnect the USB device. |
| Error code: | B40 47 |
| Description: | • E-mail transmission failed |
| Causes: | E-mail transmission has been failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | C01 512 |
| Description: | • Ink in the ink cartridge has run out (or is running out). |
| Causes: | Ink sensor is not turned ON even after inking operation has been performed for the specified period of time. (No ink) |
| Remedy: | • Ink bottle set switch: ON -> OFF or • Print drum set switch: OFF, Print drum connection signal: OFF, and Print drum lock sensor: OFF (Set an ink cartridge or pull out the print drum to cancel the error.) * For regular products only |
| Error code: | C01 563 |
| Description: | • Ink in the ink cartridge has run out (or is running out). |
| Causes: | The ink tag volume information has reached the maximum value. |
| Remedy: | • Ink bottle set switch: ON -> OFF or • Print drum set switch: OFF, Print drum connection signal: OFF, and Print drum lock sensor: OFF (Set an ink cartridge or pull out the print drum to cancel the error.) * For regular products only |
| Error code: | C01 574 |
| Description: | • Ink in the ink cartridge has run out (or is running out). |
| Causes: | No-ink error has occurred five times on the same ink cartridge. |
| Remedy: | • Ink bottle set switch: ON -> OFF or • Print drum set switch: OFF, Print drum connection signal: OFF, and Print drum lock sensor: OFF (Set an ink cartridge or pull out the print drum to cancel the error.) * For regular products only |
| Error code: | C02 200 |
| Description: | • The master for the master roll has run out (or is running out). |
| Causes: | Master end check performed every 10 ms. during master transfer detected master run out two consecutive times. |
| Remedy: | Master making unit upper cover set switch: OFF -> ON (To cancel the error: Master making unit upper cover open -> close) * For regular products only |
| Error code: | C02 240 |
| Description: | • The master for the master roll has run out (or is running out). |
| Causes: | The master tag volume information has reached the maximum value. |
| Remedy: | Master making unit upper cover set switch: OFF -> ON (To cancel the error: Master making unit upper cover open -> close) * For regular products only |
| Error code: | C02 253 |
| Description: | • The master for the master roll has run out (or is running out). |
| Causes: | No-master error has occurred five times on the same master. (When the standard detection method is selected in the test mode NO. 557 (master replacement indication detection method selection).) Otherwise, the master usage amount is larger than the predetermined value at the time nomaster error occurs. (When the new detection method is selected in the test mode NO. 557 (master replacement indication detection method selection).) |
| Remedy: | Master making unit upper cover set switch: OFF -> ON (To cancel the error: Master making unit upper cover open -> close) * For regular products only |
| Error code: | C03 308 |
| Description: | • Master disposal box is full. |
| Causes: | After the Master compression motor is turned ON toward the compression direction, compression detector is turned ON before the FG sensor pulse count exceeds the specified amount. |
| Remedy: | Turn OFF the Master disposal box set sensor, and turn ON the set sensor after a lapse of five seconds or longer. |
| Error code: | C03 311 |
| Description: | • Master disposal box is full. |
| Causes: | The master disposal software counter has reached the specified value. |
| Remedy: | Turn OFF the Master disposal box set sensor, and turn ON the set sensor after a lapse of five seconds or longer. |
| Error code: | C04 402 |
| Description: | • Paper is not set in the paper feed tray (except when auto tray is selected). |
| Causes: | Paper detection sensor is OFF. |
| Remedy: | Paper detection sensor: ON |
| Error code: | C11 590 |
| Description: | • The ink has expired. |
| Causes: | The year and month when the year and month recorded on the ink tag is added to the date of production recorded on the ink tag have passed the expiration period. |
| Remedy: | • Print drum set switch: OFF, and Print drum connection signal: OFF (Pull out the print drum to cancel the error.) |
| Error code: | C12 266 |
| Description: | • The master has expired. |
| Causes: | The year and month when the year and month recorded on the master tag is added to the date of production recorded on the master tag have passed the expiration period. |
| Remedy: | • Master making unit set switch: OFF, (Open the Master making unit to cancel the error.) |
| Error code: | C13 268 |
| Description: | • The ink and master have expired. |
| Causes: | The year and month when the year and month recorded on the ink tag and master tag are added to the date of production recorded on the master tag have passed the expiration period set in the test mode. |
| Remedy: | The error display can be cleared by any of the following: • Print drum interlock switch: OFF, and Print drum connection signal: OFF (Pull out the print drum to cancel the error.) • Master making unit interlock switch: OFF (Open the master making unit to cancel the error.) |
| Error code: | D01 526 |
| Description: | • Print drum is not set. • Print drum is not set properly. • Print drum has not been pulled out properly. |
| Causes: | The print drum has been removed. (Print drum connection signal, Print drum set switch, and Print drum lock sensor are OFF.) |
| Remedy: | Print drum set switch: ON, Print drum connection signal: ON, and Print drum lock sensor: ON (Set the print drum to cancel the error.) |
| Error code: | D01 527 |
| Description: | • Print drum is not set. • Print drum is not set properly. • Print drum has not been pulled out properly. |
| Causes: | Print drum connection signal is OFF after the print drum has been set. |
| Remedy: | Print drum set switch: ON, Print drum connection signal: ON, and Print drum lock sensor: ON (Set the print drum to cancel the error.) |
| Error code: | D01 528 |
| Description: | • Print drum is not set. • Print drum is not set properly. • Print drum has not been pulled out properly. |
| Causes: | Print drum set switch is OFF after the print drum has been set. |
| Remedy: | Print drum set switch: ON, Print drum connection signal: ON, and Print drum lock sensor: ON (Set the print drum to cancel the error.) |
| Error code: | D01 529 |
| Description: | • Print drum is not set. • Print drum is not set properly. • Print drum has not been pulled out properly. |
| Causes: | Print drum lock sensor is OFF after the print drum has been set. (Time-out duration until the Master making unit is inserted: five seconds) |
| Remedy: | Print drum set switch: ON, Print drum connection signal: ON, and Print drum lock sensor: ON (Set the print drum to cancel the error.) |
| Error code: | D01 530 |
| Description: | • Print drum is not set. • Print drum is not set properly. • Print drum has not been pulled out properly. |
| Causes: | When the print drum is pulled out, print drum connection signal is not turned OFF after a lapse of five seconds since the Print drum set switch has been turned OFF. |
| Remedy: | Print drum set switch: ON, Print drum connection signal: ON, and Print drum lock sensor: ON (Set the print drum to cancel the error.) |
| Error code: | D02 532 |
| Description: | • The print drum code does not match the machine model code. • The type of the print drum does not match that of the machine model. |
| Causes: | Incompatible print drum (print drum code not correct). |
| Remedy: | Replace it with a correct type of print drum. (So that the print drum code matches the machine model code.) |
| Error code: | D02 580 |
| Description: | • The print drum code does not match the machine model code. • The type of the print drum does not match that of the machine model. |
| Causes: | Incompatible print drum (incorrect print drum). |
| Remedy: | Replace it with a correct type of print drum. (So that the print drum code matches the machine model code.) |
| Error code: | D03 533 |
| Description: | • Ink cartridge is not set. |
| Causes: | Ink bottle set switch is OFF. |
| Remedy: | Ink bottle set switch: ON |
| Error code: | D04 534 |
| Description: | • The ink cartridge tag information is not correct. • Communication with the ink cartridge tag failed. |
| Causes: | Ink cartridge is incompatible. |
| Remedy: | Replace it with the correct type of ink cartridge. |
| Error code: | D04 560 |
| Description: | • The ink cartridge tag information is not correct. • Communication with the ink cartridge tag failed. |
| Causes: | Error due to missing ink cartridge tag. |
| Remedy: | Replace it with the correct type of ink cartridge. |
| Error code: | D04 561 |
| Description: | • The ink cartridge tag information is not correct. • Communication with the ink cartridge tag failed. |
| Causes: | Ink tag communication error (The communication with the tag has failed due to the noise.) |
| Remedy: | Replace it with the correct type of ink cartridge. |
| Error code: | D04 562 |
| Description: | • The ink cartridge tag information is not correct. • Communication with the ink cartridge tag failed. |
| Causes: | The ink tag information is not correct. Checksum error, verification error, recorded master information, etc. |
| Remedy: | Replace it with the correct type of ink cartridge. |
| Error code: | D04 564 |
| Description: | • The ink cartridge tag information is not correct. • Communication with the ink cartridge tag failed. |
| Causes: | The serial numbers did not match at a regular ink tag serial number check. |
| Remedy: | Replace it with the correct type of ink cartridge. |
| Error code: | D04 575 |
| Description: | • The ink cartridge tag information is not correct. • Communication with the ink cartridge tag failed. |
| Causes: | Tag-related software error Antenna channel selection error occurred or an attempted writing to the write protected area failed. |
| Remedy: | Replace it with the correct type of ink cartridge. |
| Error code: | D05 210 |
| Description: | • Master is not set. |
| Causes: | Master detection sensor is OFF. |
| Remedy: | Master making unit upper cover set switch: OFF (Open the master making unit upper cover to cancel the error.) |
| Error code: | D07 310 |
| Description: | • Master disposal box is not set. |
| Causes: | Master disposal box set switch is OFF. |
| Remedy: | Master disposal box set switch: ON, and Master disposal box set sensor: ON (Set the Master disposal box to cancel the error.) |
| Error code: | D08 224 |
| Description: | • Master making unit is not set. • Master making unit is not set properly. • Master making unit has not been pulled out properly. |
| Causes: | Master making unit has been pulled out. (Set switch and lock sensor are OFF.) |
| Remedy: | Master making unit set switch: ON, and Master making unit lock sensor: ON (Set the Master making unit to the machine to cancel the error.) |
| Error code: | D08 226 |
| Description: | • Master making unit is not set. • Master making unit is not set properly. • Master making unit has not been pulled out properly. |
| Causes: | After the Master making unit has been set, the Master making unit set switch is OFF. |
| Remedy: | Master making unit set switch: ON, and Master making unit lock sensor: ON (Set the Master making unit to the machine to cancel the error.) |
| Error code: | D08 227 |
| Description: | • Master making unit is not set. • Master making unit is not set properly. • Master making unit has not been pulled out properly. |
| Causes: | After the Master making unit has been set, the Master making unit lock sensor is OFF. (Timeout duration until the Master making unit is inserted: five seconds) |
| Remedy: | Master making unit set switch: ON, and Master making unit lock sensor: ON (Set the Master making unit to the machine to cancel the error.) |
| Error code: | D08 228 |
| Description: | • Master making unit is not set. • Master making unit is not set properly. • Master making unit has not been pulled out properly. |
| Causes: | After the Master making unit has been pulled out (and the Master making unit set switch has been turned OFF), the Master making unit lock sensor is ON. |
| Remedy: | Master making unit set switch: ON, and Master making unit lock sensor: ON (Set the Master making unit to the machine to cancel the error.) |
| Error code: | D09 212 |
| Description: | • Master making unit upper cover is open. |
| Causes: | Master making unit upper cover set switch is OFF. |
| Remedy: | Master making unit upper cover set switch: ON (Close the master making unit upper cover to cancel the error.) |
| Error code: | D11 535 |
| Description: | • The front cover is open. |
| Causes: | Front door set sensor is OFF. |
| Remedy: | Front door set sensor: ON |
| Error code: | D13 9 |
| Description: | • Main unit rear cover is out of the position. |
| Causes: | Main unit rear cover not set in position (rear cover set switch is OFF) |
| Remedy: | Rear cover SW: ON |
| Error code: | D17 236 |
| Description: | • Master tag information is not correct. • Communication with the master tag failed. |
| Causes: | The master type is not compatible. |
| Remedy: | Master making unit set switch: ON -> OFF, and Master making unit lock sensor: ON -> OFF (Pull out the Master making unit to cancel the error.) |
| Error code: | D17 237 |
| Description: | • Master tag information is not correct. • Communication with the master tag failed. |
| Causes: | Master error due to missing ink cartridge tag |
| Remedy: | Master making unit set switch: ON -> OFF, and Master making unit lock sensor: ON -> OFF (Pull out the Master making unit to cancel the error.) |
| Error code: | D17 238 |
| Description: | • Master tag information is not correct. • Communication with the master tag failed. |
| Causes: | Master tag communication error (The communication with the tag has failed due to the noise.) |
| Remedy: | Master making unit set switch: ON -> OFF, and Master making unit lock sensor: ON -> OFF (Pull out the Master making unit to cancel the error.) |
| Error code: | D17 239 |
| Description: | • Master tag information is not correct. • Communication with the master tag failed. |
| Causes: | Master tag information is not correct. Checksum error, verification error, recorded ink information, etc. |
| Remedy: | Master making unit set switch: ON -> OFF, and Master making unit lock sensor: ON -> OFF (Pull out the Master making unit to cancel the error.) |
| Error code: | D17 241 |
| Description: | • Master tag information is not correct. • Communication with the master tag failed. |
| Causes: | The serial numbers does not match at a regular master tag serial number check. |
| Remedy: | Master making unit set switch: ON -> OFF, and Master making unit lock sensor: ON -> OFF (Pull out the Master making unit to cancel the error.) |
| Error code: | D17 256 |
| Description: | • Master tag information is not correct. • Communication with the master tag failed. |
| Causes: | Master tag-related software error Antenna channel selection error occurred or an attempted writing to the write protected area failed. |
| Remedy: | Master making unit set switch: ON -> OFF, and Master making unit lock sensor: ON -> OFF (Pull out the Master making unit to cancel the error.) |
| Error code: | D18 522 |
| Description: | • Notification that the print drum can be pulled out. |
| Causes: | Print drum release possible. (Print drum lock solenoid is ON.) |
| Remedy: | • Print drum connection signal: ON -> OFF, and Print drum set switch: ON -> OFF or • Front door set switch: ON or • Master making unit release button: ON (Pull out the print drum or close the front door/press the Master making unit release button.) |
| Error code: | D19 223 |
| Description: | • Notification that the Master making unit can be pulled out. |
| Causes: | Master making unit pull out possible (Solenoid ON) |
| Remedy: | • Master making unit set switch: ON -> OFF, and Master making unit lock sensor: ON -> OFF or • Front door set switch: ON or • Print drum release button: ON (Pull out the Master making unit or close the front door/press the print drum release button.) |
| Error code: | D22 531 |
| Description: | • Print drum EEPROM reading/writing has failed. • Print drum EEPROM data is not correct. |
| Causes: | Print drum lock sensor is ON when the Print drum lock solenoid is ON. (Checked 100 ms. after the Print drum lock solenoid is turned ON.) |
| Remedy: | Print drum set switch: OFF, Print drum connection signal: OFF, and Print drum lock sensor: OFF |
| Error code: | D22 540 |
| Description: | • Print drum EEPROM reading/writing has failed. • Print drum EEPROM data is not correct. |
| Causes: | Data cannot be rewritten to the EEPROM in the print drum (not accessible to the EEPROM). |
| Remedy: | Print drum set switch: OFF, Print drum connection signal: OFF, and Print drum lock sensor: OFF |
| Error code: | D22 542 |
| Description: | • Print drum EEPROM reading/writing has failed. • Print drum EEPROM data is not correct. |
| Causes: | CRC error of the EEPROM in the print drum (EEPROM data error). |
| Remedy: | Print drum set switch: OFF, Print drum connection signal: OFF, and Print drum lock sensor: OFF |
| Error code: | D23 177 |
| Description: | • AF paper feeder cover is open. |
| Causes: | AF paper feeder cover is open. * Duplex AF only |
| Remedy: | Turn ON the AF paper feeder cover open/ close sensor. (Close the AF paper feeder cover.) |
| Error code: | D50 165 |
| Description: | • Scanner carriage lock is not released at the time of unpacking. |
| Causes: | The machine is powered ON with the scanner carriage lock not released. |
| Remedy: | Press the <RESET> key. (For complete solution) Release the scanner carriage lock, and then change the value in the test mode 7465 to “0”. |
| Error code: | E01 10 |
| Description: | • The battery is running out. |
| Causes: | When the power is turned ON, the remaining battery is 2.1 V or lower (to be replaced). * For control, when a value 1.6 V or lower is set for RTC. * Precautions on battery replacement: Be sure to replace the battery when the machine power is ON. If the battery is replaced when the machine power is OFF, the following two problems will occur. (1) The internal clock goes wrong. Ë Set the clock again. (2) When the power is turned ON the first time after the battery replacement, T25-026 No battery error is indicated again. Ë Switch the power OFF, then ON, and check that the error is no longer indicated. |
| Remedy: | The error display can be cleared by any of the following: • Touch the [Close] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | E02 11 |
| Description: | • Reached the scheduled maintenance time |
| Causes: | The master making count exceeded the value set in the test mode when the power is turned ON or when reset is executed. (Maintenance call) |
| Remedy: | The error display can be cleared by any of the following: • Touch the [Close] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | E02 12 |
| Description: | • Reached the scheduled maintenance time |
| Causes: | The printing count exceeded the value set in the test mode when the power is turned ON or when reset is executed. (Maintenance call) |
| Remedy: | The error display can be cleared by any of the following: • Touch the [Close] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | E02 22 |
| Description: | • Reached the scheduled maintenance time |
| Causes: | The maintenance counter in the print drum exceeded the value set in the test mode when the power is turned ON or when reset is executed. (Maintenance call) |
| Remedy: | The error display can be cleared by any of the following: • Touch the [Close] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | F01 |
| Display: | F01-xxx No Master on Print Cylinder (Drum) Make a New Master |
| Description: | • No master is detected on the print drum at the start of printing. |
| Causes: | • No master is detected on the print drum at the start of printing. |
| Remedy: | The warning display can be cleared by any of the following: • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | F02 18 |
| Description: | • The master making size is larger than the paper size (except for proof printing) (except for DtoP master making) |
| Causes: | The paper size does not match the master making size (on the print drum) at the start of printing. Paper size . Master making size (on the print drum) (Not detected when Paper size . Master making size) |
| Remedy: | Printing will be executed by any of the following: • Touch the [Continue] button. • Press the <START> key. • Press the <PROOF> key. The warning display can be cleared by any of the following: (Printing stops.) • Touch the [Stop] button. • Press the <STOP> key. • Press the <RESET> key. (Released by setting paper with equal or larger size than the master making size.) |
| Error code: | F03 16 |
| Description: | • Custom sized paper is set for the multi-up setting |
| Causes: | Attempted uses of custom sized paper with the multi-up function. |
| Remedy: | The warning display can be cleared by any of the following: • Touch the [Close] button. • Press the <STOP> key. • Press the <RESET> key. (Set standard size paper that can be used with the multi-up function to cancel the error.) |
| Error code: | F04 905 |
| Description: | • The master making count has reached the maximum. • The print quantity has reached the maximum. |
| Causes: | The master making count has reached the setting value for the upper limit count of master making. |
| Remedy: | • Touch the [Close] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | F04 906 |
| Description: | • The master making count has reached the maximum. • The print quantity has reached the maximum. |
| Causes: | The print quantity has reached the setting value for the upper limit count of print quantity. |
| Remedy: | • Touch the [Close] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | F05 19 |
| Description: | • The number of print is smaller than the minimum print quantity. |
| Causes: | The set number of print is smaller than the minimum print quantity when the <START> key is pressed in the master making mode. |
| Remedy: | Enter the number of print that is larger than the value specified as the minimum print quantity using the numeric keys |
| Error code: | F10 21 |
| Description: | • The master making size is larger than the paper size (for proof printing) |
| Causes: | The paper size does not match the master making size (on the print drum) at the start of proof printing. Paper size . Master making size (on the print drum) (Not detected when Paper size . Master making size) |
| Remedy: | Printing will be executed by any of the following: • Press the <PROOF> key. The warning display can be cleared by any of the following: (Printing stops.) • Touch the [Stop] button. • Press the <STOP> key. • Press the <RESET> key. (Released by setting paper with equal or larger size than the master making size.) |
| Error code: | F17 27 |
| Description: | • The size of the print drum inserted differ from that of the last time. |
| Causes: | The size of the print drum being set differ from that of the last time. |
| Remedy: | The warning display can be cleared by any of the following: • Select the print drum with the same size as that inserted, and press [OK]. • Select the print drum with a different size from that inserted, and press [OK] three times. • Release the print drum (and replace it with the one with the same size as that previously used). |
| Error code: | F24 37 |
| Description: | • The calculated auto reproduction ratio is out of range (processing not available). |
| Causes: | The reproduction ratio has fallen out of range at the start of operation with auto size reproduction. |
| Remedy: | • Touch the [Size Setting] button and then specify the reproduction size manually. The warning display can be cleared by any of the following: (Printing stops.) • Touch the [Stop] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | F28 435 |
| Description: | • Paper feed pressure adjustment lever is set to “CARD”. |
| Causes: | (1) At the first start of master making/printing/ proof printing operation after the power is turned ON (or after wake-up), the Paper feed pressure adjustment lever has been set to “CARD”. (2) When the Paper feed tray starts master making/printing/proof printing operation from other than the upper limit position, the Paper feed pressure adjustment lever has been set to “CARD”. |
| Remedy: | Operation (master making/printing/proof printing) is restarted by any of the following: • Press the [Continue] button. • Press the <START> key. Operation (master making/printing/proof printing) is stopped by any of the following: • Press the [Stop] button. • Press the <STOP> key. |
| Error code: | F32 713 |
| Description: | • The remaining storage memory capacity is low. |
| Causes: | The remaining capacity is inadequate at data writing to the storage memory or at the start of scanning in the scan mode. |
| Remedy: | The warning display can be cleared by any of the following. • Press the [Close] button. • Press the <STOP> key. • Press the <RESET> key. • Press the [Storage] button to clear the warning display, and then the [Storage Selection] window appears. |
| Error code: | F33 913 |
| Description: | • The remaining USB memory capacity is low. |
| Causes: | The remaining capacity is inadequate at the start of data writing or scanning (in the scan mode) to the USB memory. |
| Remedy: | The warning display can be cleared by any of the following. • Press the [Close] button. • Press the <STOP> key. • Press the <RESET> key. • Press the [USB Job List] button to clear the warning display, and then the [USB Job List] window appears. |
| Error code: | F34 835 |
| Description: | • The number of files in the folder of the storage memory reached the maximum. |
| Causes: | The number of files in the folder of the storage memory reached the maximum at the time when the data is stored in the storage memory or at the start of scanning in the scan mode. |
| Remedy: | The warning display can be cleared by any of the following. • Press the [Close] button. • Press the <STOP> key. • Press the <RESET> key. • Press the [Storage] button to clear the warning display, and then the [Storage Selection] window appears. |
| Error code: | F37 50 |
| Description: | • An original has been set on AF while in the book mode. |
| Causes: | An original has been set on AF while in book mode at the start of master making operation. An original was set on AF while in book mode. |
| Remedy: | The warning display can be cleared by any of the following: • Touch the [Close] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | F38 43 |
| Description: | • The same password is already used for another user registration at the time of user password registration. |
| Causes: | At user registration in the user control function, the entered password has already been registered by another user. |
| Remedy: | Press the <RESET> key. |
| Error code: | F39 44 |
| Description: | • Attempted login by a suspended user |
| Causes: | A suspended user has logged in using the user control function. |
| Remedy: | Press the <RESET> key. |
| Error code: | F43 902 |
| Description: | • The master making size is larger than the paper size (at DtoP master making). |
| Causes: | The paper size and the original size are not compatible at the start of DtoP master making operation. Paper size . Master making size for the job (page size) (Not detected when Paper size . Master making size) |
| Remedy: | Printing is executed by any of the following: • Touch the [Continue] button. • Press the <START> key. • Press the <PROOF> key. The warning display is cleared by any of the following: (Printing stops.) • Touch the [Stop] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | F44 901 |
| Description: | • The original size cannot be detected. |
| Causes: | Original size detection failed. (Original did not conform to the detection specification.) |
| Remedy: | • Touch the [Size Setting] button and then specify the reproduction size manually. The warning display can be cleared by any of the following: (Printing stops.) • Touch the [Stop] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | F45 959 |
| Description: | • Original is not detected successfully. • Original is not set. |
| Causes: | Master making or RLP output has been started without an original. |
| Remedy: | Printing is executed by any of the following: • Touch the [Continue] button. • Press the <START> key. The warning display is cleared by any of the following: (Printing stops.) • Touch the [Stop] button. • Press the <STOP> key. • Press the <RESET> key. (Set the original again to cancel the error.) |
| Error code: | F45 981 |
| Description: | • Original is not detected successfully. • Original is not set. |
| Causes: | Original has not been detected when [Next] is pressed on the multi-up count entry screen of the multi-up wizard. |
| Remedy: | Printing is executed by any of the following: • Touch the [Continue] button. • Press the <START> key. The warning display is cleared by any of the following: (Printing stops.) • Touch the [Stop] button. • Press the <STOP> key. • Press the <RESET> key. (Set the original again to cancel the error.) |
| Error code: | F47 904 |
| Description: | • An original is set on AF when postcard size reproduction has been set. |
| Causes: | Master making or RLP output is started when [A4->Card] reproduction has been selected and an original has been set on AF. An original is set on AF when [A4->Card] reproduction is selected. |
| Remedy: | The warning display can be cleared by any of the following: • Touch the [Close] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | F48 955 |
| Description: | • The original size is out of range for the multi-up setting. (Processing for the original size is not available.) |
| Causes: | The original is out of range of possible size or is custom sized paper at the time of multi-up setting. |
| Remedy: | Reset, Stop (Warning display cleared) |
| Error code: | F51 548 |
| Description: | • The ink has expired. |
| Causes: | The year and month when the year and month recorded on the ink tag is added to the date of production recorded on the ink tag is earlier than the year and month stored on the machine. |
| Remedy: | • Touch the [Close] button. • Press the <RESET> key. |
| Error code: | F52 912 |
| Description: | • RLP information has not been acquired. |
| Causes: | Use of RLP mode not possible (RLP information has not been acquired) |
| Remedy: | The warning display can be cleared by any of the following: • Touch the [Close] button. • Press the <RESET> key. • Press the mode switching key. |
| Error code: | F56 265 |
| Description: | • The master has expired. |
| Causes: | The year and month when the year and month recorded on the master tag is added to the date of production recorded on the master tag is earlier than the year and month stored on the machine. |
| Remedy: | • Touch the [Close] button. • Press the <RESET> key. |
| Error code: | F57 267 |
| Description: | • The ink and master have expired. |
| Causes: | The year and month when the year and month recorded on the ink tag and master tag are added to the date of production recorded on the ink tag and master tag are earlier than the year and month stored on the machine. |
| Remedy: | • Touch the [Close] button. • Press the <RESET> key. |
| Error code: | F58 927 |
| Description: | • NET-D initialization in process |
| Causes: | Use of RLP mode not possible (NET-D initializing) |
| Remedy: | The warning display can be cleared by any of the following: • Touch the [Close] button. • Press the <RESET> key. • Press the mode switching key. |
| Error code: | F60 929 |
| Description: | • Printing operation has been started at print quantity “0” when RLP auto-ink is active. |
| Causes: | Auto-link master making continuation confirmation (when print quantity is 0). |
| Remedy: | Press the <START> key to start master making. The warning display can be cleared by any of the following: (Printing stops.) • Touch the [Stop] button. • Press the <RESET> key. • Press the <STOP> key. |
| Error code: | F62 956 |
| Description: | • An error has occurred on RLP. |
| Causes: | An error has occurred on the RLP side when RLP auto-ink is active. |
| Remedy: | The warning display is cleared by any of the following: • Touch the [Stop] button. • Press the <RESET> key. • Press the <STOP> key. • If any other Prioa is available, press the [Link Switch] button to select another option. (The [Link Switch] button is not displayed when no other Prioa is available.) |
| Error code: | F64 964 |
| Description: | • A command for unavailable function has been issued while DtoP job is in process. |
| Causes: | A command for any of the following functions is issued: DtoP job reception/Data-Map/Exclusive functions (scan mode, overlay, editor, storage) in awaiting output status |
| Remedy: | Touch [Close] or switch modes using the mode key. |
| Error code: | F65 965 |
| Description: | • A nonstandard size original is set when auto size for saving is selected (at first page scanning of original). |
| Causes: | At the start of scanning, auto size (for saving data) is selected and original size is nonstandard. * For scan and storage management, only the first page of the original is the target of detection of F65. For second page and later, F65 warning will not be displayed even if it is applicable due to a different reproduction ratio or original size. |
| Remedy: | [Stop]/Reset, Stop (Warning display clear) [Saving Format] (Manual size selection) |
| Error code: | F73 975 |
| Description: | • Tray cannot be selected among the reproduction ratio and original size at auto tray selection (at RLP output). |
| Causes: | At the start of RLP, the specified fixed size reproduction and detected original size do not match. Otherwise, zoom/independent size reproduction has been specified. |
| Remedy: | [Manual Feed]: Clear the warning and output with [Multi- Purpose Tray] selected and the output size fixed to [A3]. [Paper Select]: Clear the warning and display the RLP paper selection screen. (If paper has been selected before starting the operation, F18 will not be indicated.) Press the [Stop] button, <RESET> key, or<STOP> key to clear the warning message. |
| Error code: | F74 980 |
| Description: | • When high speed printing is set, the temperature is lower than the predetermined value. |
| Causes: | High speed printing has been performed under a temperature below 15°C. |
| Remedy: | Printing status goes back to standby by any of the following: (High speed is canceled.) • Press the [Stop] button. • Press the <STOP> key. High speed is canceled by any of the following, and printing starts in “speed 3”: • Press the [Continue] button. • Press the <START> key. |
| Error code: | F78 731 |
| Description: | • The stage cover is opened during digitizing operation. |
| Causes: | The Stage cover is opened during digitizing operation. |
| Remedy: | Close the stage cover to clear the warning window. Press the [Close] button to clear the warning message. |
| Error code: | F79 732 |
| Description: | • No original is set when the digitizer starts rescanning. |
| Causes: | No original is detected when the digitizer starts rescanning. |
| Remedy: | Press the <START> key to start scanning. Press the [Close] button (<STOP> or <RESET> key) to clear the warning window and to return to the original screen (Image processing window). (Scanning is canceled.) |
| Error code: | F85 997 |
| Description: | • Job deletion failed on external CI. • Data reception failed on external CI. |
| Causes: | Job deletion has failed on the external CI side. |
| Remedy: | [Close]: Mode selection screen <START>: Scanning starts. |
| Error code: | F85 998 |
| Description: | • Job deletion failed on external CI. • Data reception failed on external CI. |
| Causes: | Scan data reception has failed on the external CI side. |
| Remedy: | [Close]: Mode selection screen <START>: Scanning starts. |
| Error code: | F90 957 |
| Description: | • The number of ink stock decreased to the set value or less. |
| Causes: | Number of stocks of ink of applicable color (set value) † Number of stocks (subtracted counter value). |
| Remedy: | The warning display can be cleared by any of the following: • Touch the [Close] button. • Press the <RESET> key. • Press the <STOP> key. • Touch the [No] button. Touching the [Yes] button displays the [Sending E-mail] window. |
| Error code: | F91 958 |
| Description: | • The number of master stock decreased to the set value or less. |
| Causes: | Number of master stock (set value) † Number of stocks (subtracted counter value). |
| Remedy: | The warning display can be cleared by any of the following: • Touch the [Close] button. • Press the <RESET> key. • Press the <STOP> key. • Touch the [No] button. Touching the [Yes] button displays the [Sending E-mail] window. |
| Error code: | F94 7 |
| Description: | • Protection mode is set but the master has not been discarded (when the power is turned ON) (at wake-up) (when the print drum is inserted) |
| Causes: | The flag for being protected remains when the power is turned ON, at wake-up, or when the print drum is inserted. |
| Remedy: | Confidential action will be executed by any of the following: • Press the [OK] button. • Press the <START> key. |
| Error code: | F95 8 |
| Description: | • Protection mode is set (at job completion) (except when connected to vendor) |
| Causes: | Job completed when [Protect] in [Admin.] is ON. |
| Remedy: | Confidential action will be executed by any of the following: • Press the [OK] button. • Press the <START> key. The warning display can be cleared by any of the following: • Press the [Cancel] button. • Press the <STOP> key. |
| Error code: | F96 918 |
| Description: | • ID counter report due date has been reached. |
| Causes: | The specified ID counter report due date has been reached. |
| Remedy: | • Touch the [Close] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | F97 928 |
| Description: | • Counter report due date has been reached. |
| Causes: | The specified counter report due date has been reached. |
| Remedy: | • Touch the [Close] button. • Press the <STOP> key. • Press the <RESET> key. |
| Error code: | H01 566 |
| Description: | • The ink cartridge tag information is not reliable. |
| Causes: | Parameter entry is required due to the unreliability of the ink tag color information, normal state viscosity information, and proofprint viscosity information. |
| Remedy: | Enter parameters and press the <START> key. |
| Error code: | H02 567 |
| Description: | • The ink cartridge tag information of normal state viscosity is not reliable. |
| Causes: | Parameter entry is required due to the unreliability of the ink tag information of normal state viscosity. |
| Remedy: | Enter parameters and press the <START> key. |
| Error code: | H03 568 |
| Description: | • The ink cartridge tag information of proof-print viscosity is not reliable. |
| Causes: | Parameter entry is required due to the unreliability of the ink tag information of proofprint viscosity. |
| Remedy: | Enter parameters and press the <START> key. |
| Error code: | H04 242 |
| Description: | • The master tag information is not reliable. |
| Causes: | Parameter entry is required due to the unreliability of the master tag information of sensitivity, normal print pressure, and FP normal print pressure. |
| Remedy: | Enter parameters and press the <START> key. |
| Error code: | H05 243 |
| Description: | • The master tag information of support is not reliable. |
| Causes: | Parameter entry is required due to the unreliability of the master tag information of normal print pressure. |
| Remedy: | Enter parameters and press the <START> key. |
| Error code: | H06 244 |
| Description: | • The master tag information of FP support is not reliable. |
| Causes: | Parameter entry is required due to the unreliability of the master tag information of FP print pressure. |
| Remedy: | Enter parameters and press the <START> key. |
| Error code: | H08 578 |
| Description: | General supply (ink) expiration period setting |
| Causes: | At the occurrence of H01 error, enter the expiration month of general supply (ink). |
| Remedy: | Enter the expiration month and press the <START> key. |
| Error code: | H09 579 |
| Description: | General supply (ink) expiration period setting |
| Causes: | At the occurrence of H01 error, enter the expiration year of general supply (ink). |
| Remedy: | Enter the expiration year and press the <START> key. |
| Error code: | H10 263 |
| Description: | General supply (master) expiration period setting |
| Causes: | At the occurrence of H04 error, enter the expiration month of general supply (master). |
| Remedy: | Enter the expiration month and press the <START> key. |
| Error code: | H11 264 |
| Description: | General supply (master) expiration period setting |
| Causes: | At the occurrence of H04 error, enter the expiration year of general supply (master). |
| Remedy: | Enter the expiration year and press the <START> key. |
| Error code: | T01 520 |
| Description: | • The print drum is not in proper position. • The print drum is not locked when the print drum is in operation. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | Main motor lock detected The Main motor FG sensor pulse count for the specified speed is reduced to half. Not detected for 200 ms. after the motor has been activated. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T01 521 |
| Description: | • The print drum is not in proper position. • The print drum is not locked when the print drum is in operation. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | Clamp sensor B is not altered after the pulse has exceeded 3033 while the Main motor is ON. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T01 524 |
| Description: | • The print drum is not in proper position. • The print drum is not locked when the print drum is in operation. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | The clamp is not on the home position when the print drum is in operation (except at master removal). |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T01 537 |
| Description: | • The print drum is not in proper position. • The print drum is not locked when the print drum is in operation. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | Position-B stop operation failed. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T01 538 |
| Description: | • The print drum is not in proper position. • The print drum is not locked when the print drum is in operation. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | The print drum is not locked when the print drum is in operation. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T01 582 |
| Description: | • The print drum is not in proper position. • The print drum is not locked when the print drum is in operation. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | Reaching the specified angle is not detected even after three detection operation have been performed by the Print drum home position sensor. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T02 400 |
| Description: | • The Paper feed tray is not in proper position. • Paper feed tray elevator motor is overloaded. |
| Causes: | Elevator upper limit position detection and Elevator lower limit position detection is ON at the same time. |
| Remedy: | Press the <RESET> key. |
| Error code: | T02 401 |
| Description: | • The Paper feed tray is not in proper position. • Paper feed tray elevator motor is overloaded. |
| Causes: | Elevator motor overload detected The overcurrent port (1.0A) of the Elevator motor has been ON five consecutive times (by 10 ms. interval polling). |
| Remedy: | Press the <RESET> key. |
| Error code: | T02 404 |
| Description: | • The Paper feed tray is not in proper position. • Paper feed tray elevator motor is overloaded. |
| Causes: | After the Elevator motor has been turned ON from the paper feed lower limit position to the upward direction, the paper feed lower limit position sensor is not turned OFF after a lapse of two seconds. |
| Remedy: | Press the <RESET> key. |
| Error code: | T02 405 |
| Description: | • The Paper feed tray is not in proper position. • Paper feed tray elevator motor is overloaded. |
| Causes: | After the Elevator motor has been turned ON to the upward direction, the paper feed upper limit position sensor is not turned ON after a lapse of 12 seconds. |
| Remedy: | Press the <RESET> key. |
| Error code: | T02 406 |
| Description: | • The Paper feed tray is not in proper position. • Paper feed tray elevator motor is overloaded. |
| Causes: | After the Elevator motor has been turned ON from the paper feed upper limit position to the downward direction, the paper feed upper limit position sensor is not turned OFF after a lapse of two seconds. |
| Remedy: | Press the <RESET> key. |
| Error code: | T02 407 |
| Description: | • The Paper feed tray is not in proper position. • Paper feed tray elevator motor is overloaded. |
| Causes: | After the Elevator motor has been turned ON to the downward direction, the paper feed lower limit position sensor is not turned ON after a lapse of 12 seconds. |
| Remedy: | Press the <RESET> key. |
| Error code: | T02 408 |
| Description: | • The Paper feed tray is not in proper position. • Paper feed tray elevator motor is overloaded. |
| Causes: | The upper limit sensor has been OFF for two seconds or longer while the elevator servo is in action. |
| Remedy: | Press the <RESET> key. |
| Error code: | T02 434 |
| Description: | • The Paper feed tray is not in proper position. • Paper feed tray elevator motor is overloaded. |
| Causes: | Printing is attempted when the Elevator upper limit sensor is OFF in the special paper feed mode. |
| Remedy: | Press the <RESET> key. |
| Error code: | T03 500 |
| Description: | • The clamp is not in proper position. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | The Clamp sensor is OFF at the end of the Clamp unit initialize action and home positioning action. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T03 501 |
| Description: | • The clamp is not in proper position. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | Clamp sensor B is not altered within one second when the clamp MOT rotates in the normal direction. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T03 502 |
| Description: | • The clamp is not in proper position. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | Clamp sensor B is not altered within one second when the clamp MOT rotates in the reverse direction. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T03 503 |
| Description: | • The clamp is not in proper position. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | The Clamp sensor A is not turned ON within three seconds at the Clamp initializing action. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T03 504 |
| Description: | • The clamp is not in proper position. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | Clamp sensor A and B have different logic at the start of the Clamp releasing action. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T03 505 |
| Description: | • The clamp is not in proper position. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | Clamp sensor A and B have different logic at the start of print drum position-A compensation operation. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T03 506 |
| Description: | • The clamp is not in proper position. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | Clamp sensor A and B have different logic at the start of clamp home positioning action. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T03 507 |
| Description: | • The clamp is not in proper position. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | Clamp sensor A is ON at the end of clamp releasing action. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T03 508 |
| Description: | • The clamp is not in proper position. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | Clamp sensor A is ON at the completion of the print drum position-A compensation operation. |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T03 545 |
| Description: | • The clamp is not in proper position. • The clamp is not in proper position when the print drum is in operation (except at master removal). |
| Causes: | The clamp is not on the home position when the print drum is in operation (attributed to the Clamp motor). |
| Remedy: | Press the <RESET> key. -> Process PF/ES. |
| Error code: | T04 513 |
| Description: | • Ink overflow has occurred in the print drum. |
| Causes: | The overflow sensor has detected it ON specified number of consecutive times by 10 ms. interval check. |
| Remedy: | Press the <RESET> key and Turn OFF the overflow sensor. |
| Error code: | T05 603 |
| Description: | • The Vertical print positioning pulse motor does not operate properly. |
| Causes: | The vertical HP sensor is not turned ON after a lapse of the specified period of time since the motor is turned ON to the downward direction during vertical home positioning action. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation (to return to the home position). |
| Error code: | T05 604 |
| Description: | • The Vertical print positioning pulse motor does not operate properly. |
| Causes: | The vertical HP sensor is not turned OFF after a lapse of the specified period of time since the motor is turned ON to the upward direction during vertical home positioning action. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation (to return to the home position). |
| Error code: | T05 605 |
| Description: | • The Vertical print positioning pulse motor does not operate properly. |
| Causes: | The logical value of the sensor at the destination differ from the theoretical value even after the vertical PM operation ended due to the sensor stop mode. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation (to return to the home position). |
| Error code: | T05 612 |
| Description: | • The Vertical print positioning pulse motor does not operate properly. |
| Causes: | The logical value of the sensor at the destination differ from the theoretical value even after the vertical PM operation ended due to the sensor stop mode. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation (to return to the home position). |
| Error code: | T05 619 |
| Description: | • The Vertical print positioning pulse motor does not operate properly. |
| Causes: | Vertical home positioning action at a pulse of -98 is not completed after a lapse of the specified period of time. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation (to return to the home position). |
| Error code: | T05 632 |
| Description: | • The Vertical print positioning pulse motor does not operate properly. |
| Causes: | The vertical PM operation is not completed after a lapse of the specified period of time in the counter stop mode. Otherwise, the operation is not completed after a lapse of the specified period of time since the sensor edge detection until the PM stops in the sensor stop mode. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation (to return to the home position). |
| Error code: | T09 720 |
| Description: | • Communication with job separator failed |
| Causes: | Sorter communication error: Two consecutive retry commands have been received. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T11 600 |
| Description: | • The Print pressure control pulse motor does not operate properly. |
| Causes: | The Print pressure HP sensor is not turned ON after a lapse of 3.9 seconds when pressure increases during home positioning at pressure control home positioning action. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation (to return to the home position). |
| Error code: | T11 601 |
| Description: | • The Print pressure control pulse motor does not operate properly. |
| Causes: | The Print pressure HP sensor is not turned OFF after a lapse of 4.6 seconds when pressure reduces during home positioning at pressure control home positioning action. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation (to return to the home position). |
| Error code: | T11 602 |
| Description: | • The Print pressure control pulse motor does not operate properly. |
| Causes: | The logical value of the sensor at the destination differ from the theoretical value even after the print pressure PM operation ended due to the sensor stop mode. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation (to return to the home position). |
| Error code: | T11 614 |
| Description: | • The Print pressure control pulse motor does not operate properly. |
| Causes: | Pressure control home positioning action at a pulse of -1000 is not completed after a lapse of the specified period of time (1.2 times of the calculated positioning time). (Time-out) |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation (to return to the home position). |
| Error code: | T11 631 |
| Description: | • The Print pressure control pulse motor does not operate properly. |
| Causes: | The Pressure control PM operation is not completed after a lapse of the specified period of time in the counter stop mode. Otherwise, the operation is not completed after a lapse of the specified period of time in the sensor stop mode. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation (to return to the home position). |
| Error code: | T12 301 |
| Description: | • Master compression motor does not operate properly. • Master removal motor does not operate properly. |
| Causes: | Master compression motor lock detected. The RMGA compression detection has been turned ON during the lifting action of the compression plate. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T12 302 |
| Description: | • Master compression motor does not operate properly. • Master removal motor does not operate properly. |
| Causes: | The compression FG width has got larger than the specified value at the preparation operation before the Master compression plate home positioning action. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T12 305 |
| Description: | • Master compression motor does not operate properly. • Master removal motor does not operate properly. |
| Causes: | After the Master compression motor has been turned ON toward the return direction, the Master compression HP sensor is not turned ON after a lapse of 7.5 seconds. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T12 306 |
| Description: | • Master compression motor does not operate properly. • Master removal motor does not operate properly. |
| Causes: | After the Master compression motor has been turned ON toward the compression direction, the Master compression HP sensor is not turned OFF after a lapse of 2 seconds. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T12 307 |
| Description: | • Master compression motor does not operate properly. • Master removal motor does not operate properly. |
| Causes: | (1) After the Master compression motor has been turned ON toward the compression direction, the compression detector is not turned ON after a lapse of 7.5 seconds. (2) After the Master compression motor has been turned ON toward the compression direction, the Master compression FG sensor pulse count does not count 20 pulse after a lapse of 800 ms. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T12 309 |
| Description: | • Master compression motor does not operate properly. • Master removal motor does not operate properly. |
| Causes: | Master compression motor lock detected The Master compression motor FG sensor has been detected unaltered 50 consecutive times (by 10 ms. interval polling). |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T12 316 |
| Description: | • Master compression motor does not operate properly. • Master removal motor does not operate properly. |
| Causes: | Master disposal motor lock detected The Master disposal motor FG sensor pulse count for the specified speed has been reduced to half. Not detected for 200 ms. after the motor is activated. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T13 203 |
| Description: | • Cutter does not operate normally. • Master was not cut properly. |
| Causes: | When the cutter blade moves from the home position, the Cutter HP switch is not turned OFF after a lapse of 100 ms. (Rotary) |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T13 204 |
| Description: | • Cutter does not operate normally. • Master was not cut properly. |
| Causes: | When the cutter blade moves, the Cutter HP switch is not turned ON after a lapse of 300 ms. (Rotary) |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T13 205 |
| Description: | • Cutter does not operate normally. • Master was not cut properly. |
| Causes: | After the master has been cut, the master positioning sensor is still ON even when the print drum has rotated by the specified angle. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T13 221 |
| Description: | • Cutter does not operate normally. • Master was not cut properly. |
| Causes: | The Cutter HP switch and cutter stop position switch are turned ON at the same time (shuttle). |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T13 222 |
| Description: | • Cutter does not operate normally. • Master was not cut properly. |
| Causes: | When the cutter returns to the home position, the Cutter HP switch is not turned ON after a lapse of 450 ms. |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T13 231 |
| Description: | • Cutter does not operate normally. • Master was not cut properly. |
| Causes: | When the cutter blade moves from the home position to cut the master, the Cutter HP switch is not turned OFF after a lapse of 500 ms. (Shuttle) |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T13 232 |
| Description: | • Cutter does not operate normally. • Master was not cut properly. |
| Causes: | When the operation to cut the master is performed, the Cutter stop position switch is not turned ON after a lapse of 2 ms. (Shuttle) |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T13 233 |
| Description: | • Cutter does not operate normally. • Master was not cut properly. |
| Causes: | When the cutter returns to the home position from the cutter stop position, the Cutter stop position switch is not turned OFF after a lapse of 500 ms. (Shuttle) |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T13 234 |
| Description: | • Cutter does not operate normally. • Master was not cut properly. |
| Causes: | When the cutter takes the home positioning action, the Cutter HP switch is not turned ON after a lapse of two seconds. (Shuttle) |
| Remedy: | Press the <RESET> key. -> Perform the recovery operation. |
| Error code: | T14 114 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Faulty machine parameters |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 115 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Scanner operation fails to complete within the specified period of time. |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 116 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Awaiting black shading time-out (Black compensation fails to complete within the specified period of time.) |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 117 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Awaiting white shading time-out (White compensation fails to complete within the specified period of time.) |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 123 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Awaiting offset adjustment time-out (When the pixel data of black level is to be loaded from the scanner GA for offset adjustment, the scanner GA does not respond after a lapse of the specified period of time.) |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 124 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Awaiting gain adjustment time-out (When the pixel data of white level is to be loaded from the scanner GA for gain adjustment, the scanner GA does not respond after a lapse of the specified period of time.) |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 125 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Offset adjustment process fails to complete. (The process does not complete within the specifies number of times.) |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 126 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Gain adjustment process fails to complete. (The process does not complete within the specifies number of times.) |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 135 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Device failure at offset adjustment |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 136 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Device failure at gain adjustment |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 137 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Device failure at black shading |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 138 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | Device failure at white shading |
| Remedy: | Press the <RESET> key. |
| Error code: | T14 170 |
| Description: | • FB does not operate normally. • Shading compensation is not processed normally. • Offset/gain adjustment is not performed normally. |
| Causes: | The logical value of the sensor at the destination differ from the theoretical value even after the reading PM operation ended due to the sensor stop mode. |
| Remedy: | Press the <RESET> key. |
| Error code: | T15 130 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | AF command reception time-out error of RG unit This error will be issued in the following conditions: A command sent from RG to AF that has not been replied to within the specified period of time is resent, but still no reply is received after a lapse of the specified period of time. * Common with Duplex AF |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 131 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | RG unit received an undefined command from AF. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 132 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | RG unit detected a communication sequence error on the AF unit. * Issued on the AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 133 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | AF communication error on the RG unit (ACK, NAK error has occurred.) * Common with Duplex AF |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 134 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | RG unit failed to send data to AF within the specified period of time. This error will be issued in the following conditions: A command sent from AF to RG that has not been replied to within the specified period of time is resent, but still no reply is received after a lapse of the specified period of time. * Common with Duplex AF |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 151 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | AF setting value writing to the flash ROM failed. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 152 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | AF setting value reading from the flash ROM failed. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 153 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | At the time of AF firmware download, AF is not ready for downloading. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 155 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | At the time of AF firmware download, flash ROM erasing has been failed. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 157 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | At the time of AF firmware download, writing of program to flash ROM has been failed. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 158 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | At the time of AF firmware download, switching to the area where program is to be executed has been failed. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 161 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | AF not connected * Common with Duplex AF |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T15 199 |
| Description: | • AF does not operate normally. • AF is not connected. • Adjustment of AF sensors has failed. |
| Causes: | For the sleep command from the machine to AF, AF has sent a notification that indicates sleep preparation failure. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T19 207 |
| Description: | • TPH pressurization/ depressurization does not operate properly. (TPH pressure sensor remains unaltered.) |
| Causes: | When the TPH pressure motor operates to reduce pressure (or during home positioning action), the TPH pressure sensor is not turned OFF after a lapse of two seconds. |
| Remedy: | Press the <RESET> key. |
| Error code: | T19 208 |
| Description: | • TPH pressurization/ depressurization does not operate properly. (TPH pressure sensor remains unaltered.) |
| Causes: | When the TPH pressure motor operates to reduce pressure, the TPH pressure sensor is not turned ON after a lapse of two seconds. |
| Remedy: | Press the <RESET> key. |
| Error code: | T19 216 |
| Description: | • TPH pressurization/ depressurization does not operate properly. (TPH pressure sensor remains unaltered.) |
| Causes: | When the TPH pressure motor applies a force to begin compression, the TPH pressure sensor is not turned OFF after a lapse of two seconds. |
| Remedy: | Press the <RESET> key. |
| Error code: | T19 217 |
| Description: | • TPH pressurization/ depressurization does not operate properly. (TPH pressure sensor remains unaltered.) |
| Causes: | When the TPH pressure motor applies a force to begin compression, the TPH pressure sensor is not turned ON after a lapse of two seconds. |
| Remedy: | Press the <RESET> key. |
| Error code: | T20 416 |
| Description: | • Paper ejection wing does not operate properly. • Paper ejection motor is overloaded. |
| Causes: | Paper ejection motor overload detected The overcurrent port (2A) of the Elevator motor has been ON 12 consecutive times (by 10 ms. interval polling). |
| Remedy: | Press the <RESET> key. |
| Error code: | T20 437 |
| Description: | • Paper ejection wing does not operate properly. • Paper ejection motor is overloaded. |
| Causes: | Paper ejection motor lock detected The Paper ejection motor FG sensor pulse count for the specified speed is reduced to half. Not detected for 200 ms. after the motor has been activated. |
| Remedy: | Press the <RESET> key. |
| Error code: | T20 442 |
| Description: | • Paper ejection wing does not operate properly. • Paper ejection motor is overloaded. |
| Causes: | The logical value of the sensor at the destination differ from the theoretical value even after the Paper ejection wing PM operation ended due to the sensor stop mode. |
| Remedy: | Press the <RESET> key. |
| Error code: | T20 456 |
| Description: | • Paper ejection wing does not operate properly. • Paper ejection motor is overloaded. |
| Causes: | The Paper ejection wing PM operation is not completed after a lapse of the specified period of time in the counter stop mode. Otherwise, the operation is not completed after a lapse of the specified period of time in the sensor stop mode. |
| Remedy: | Press the <RESET> key. |
| Error code: | T24 539 |
| Description: | • The ink motor does not operate properly. |
| Causes: | Ink motor lock detected Then Ink motor FG sensor is not altered after a lapse of 200 ms. since the inking motor has been turned ON. |
| Remedy: | Press the <RESET> key. |
| Error code: | T25 26 |
| Description: | • Battery run out |
| Causes: | The battery has run out. * After resolving the error, set the clock again. |
| Remedy: | Press the <RESET> key (and replace the battery). |
| Error code: | T90 1003 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Mac address error occurred when activating network communication. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1006 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network driver has failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1007 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Setting of Mac address for the network driver has failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1008 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1009 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Saving the memory pooling area for the network processing section has failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1010 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Making the IP instance has failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1011 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Activating IPv6 has failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1012 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Activating the TCP communication has failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1013 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Activating the UDP communication has failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1014 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Activating the IP packet fragment has failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1015 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the BSD layer has failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1016 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Setting of IP address has failed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1017 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. * Network cannot be used. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1018 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. * DtoP with RAW cannot be performed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1019 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. * DtoP with FTP cannot be performed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1020 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. * Cannot output to Prioa. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1021 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. * RISO console cannot be used. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1022 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. * DtoP with LPR cannot be performed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1023 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. * DtoP with IPP cannot be performed. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1024 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. * Cannot send a message |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1025 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. * Cannot respond to the MIB acquirement command from a PC. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1026 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. * Cannot output to Prioa. |
| Remedy: | Press the <RESET> key. |
| Error code: | T90 1027 |
| Description: | • Mac address is not correct. • Network behavior is not correct. |
| Causes: | Initializing the network processing section has failed. * Cannot output to Prioa. |
| Remedy: | Press the <RESET> key. |
| Error code: | T91 13 |
| Description: | • The data acquired from RTC is not correct. |
| Causes: | The date and time data acquired from RTC is not correct. |
| Remedy: | Press the <RESET> key. |
| Error code: | T92 570 |
| Description: | • Access to the print drum EEPROM has been attempted at a time when it is not possible. |
| Causes: | Access to the print drum EEPROM is attempted when the print drum lock is released. |
| Remedy: | Press the <RESET> key. |
| Error code: | T93 932 |
| Description: | • No response from NET-D |
| Causes: | NIC does not respond when being accessed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T93 933 |
| Description: | • No response from NET-D |
| Causes: | No response in 90 seconds during NET-D initialization. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T94 225 |
| Description: | • TPH code does not match the machine model code. |
| Causes: | When the power is turned ON (only in case the Master making unit has been inserted) or when the Master making unit is inserted, the TPH code does not match the machine model code. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T96 171 |
| Description: | • The information to be set in the test mode is not set. • The relationship between values set in the test mode are not correct. |
| Causes: | TPH resistance not specified |
| Remedy: | Enter parameters in the test mode. |
| Error code: | T96 172 |
| Description: | • The information to be set in the test mode is not set. • The relationship between values set in the test mode are not correct. |
| Causes: | Scanner adjustment value not specified |
| Remedy: | Enter parameters in the test mode. |
| Error code: | T96 433 |
| Description: | • The information to be set in the test mode is not set. • The relationship between values set in the test mode are not correct. |
| Causes: | Paper width potentiometer is not specified or relationship between setting values are not correct. |
| Remedy: | Enter parameters in the test mode. |
| Error code: | T96 569 |
| Description: | • The information to be set in the test mode is not set. • The relationship between values set in the test mode are not correct. |
| Causes: | Print drum color or ink category is not specified. |
| Remedy: | Enter parameters in the test mode. |
| Error code: | T96 613 |
| Description: | • The information to be set in the test mode is not set. • The relationship between values set in the test mode are not correct. |
| Causes: | Print pressure compensation not set. |
| Remedy: | Enter parameters in the test mode. |
| Error code: | T96 972 |
| Description: | • The information to be set in the test mode is not set. • The relationship between values set in the test mode are not correct. |
| Causes: | REv storage area has not been initialized. |
| Remedy: | Enter parameters in the test mode. |
| Error code: | T97 939 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: PC card not set |
| Remedy: | Press the <RESET> key. |
| Error code: | T97 941 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: Device error (non-CF card) |
| Remedy: | Press the <RESET> key. |
| Error code: | T97 942 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: File creation failed (The same file already exists.) |
| Remedy: | Press the <RESET> key. |
| Error code: | T97 943 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: Unformatted |
| Remedy: | Press the <RESET> key. |
| Error code: | T97 944 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: Media ID error |
| Remedy: | Press the <RESET> key. |
| Error code: | T97 945 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: Media error (CF card that is not accessible) |
| Remedy: | Press the <RESET> key. |
| Error code: | T97 946 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: Insufficient disk capacity (insufficient memory capacity in CF card) |
| Remedy: | Press the <RESET> key. |
| Error code: | T97 990 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: File not found in the specified drive |
| Remedy: | Press the <RESET> key. |
| Error code: | T97 991 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: Attempted access to a file that is not open to public |
| Remedy: | Press the <RESET> key. |
| Error code: | T97 992 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: File pointer for file information storage folder already used |
| Remedy: | Press the <RESET> key. |
| Error code: | T97 993 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: Setting of address to be loaded for data transmission to mechanical control PCB not correct |
| Remedy: | Press the <RESET> key. |
| Error code: | T97 994 |
| Description: | • PC card cannot be accessed normally. |
| Causes: | PC card access error: File deletion failed |
| Remedy: | Press the <RESET> key. |
| Error code: | T98 1005 |
| Description: | • Hardware error |
| Causes: | When the power is turned ON, the counter value stored in the FRAM of the main circuit board exceeds the upper limit value. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 119 |
| Description: | • Hardware error |
| Causes: | Faulty Image PCB (Image processing IC memory check has failed.) (Image processing IC check is executed at initialization.) |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 129 |
| Description: | • Hardware error |
| Causes: | Scanner GA PCB failure (Scanner GA memory check error has occurred.) |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 2 |
| Description: | • Hardware error |
| Causes: | No response from the NeoROSA PCB. At startup, if the NeoROSA PCB connection signal has been detected but NeoROSA PCB does not respond, T98-069 will be detected, to be overridden by this error point. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 245 |
| Description: | • Hardware error |
| Causes: | Master transfer operation time-out error on writing PM at the master making action (except for sensor based actions) |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 246 |
| Description: | • Hardware error |
| Causes: | Master transfer operation time-out error on loading PM at the master making action (except for sensor based actions) |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 25 |
| Description: | • Hardware error |
| Causes: | RF tag PCB failure (The initial communication with the RF tag PCB has failed.) |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 28 |
| Description: | • Hardware error |
| Causes: | Test mode No. 103 (storing of machine settings) has failed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 29 |
| Description: | • Hardware error |
| Causes: | Test mode No. 105 (restoration of machine settings) has failed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 34 |
| Description: | • Hardware error |
| Causes: | Data cannot be rewritten to the EEPROM on the machine (not accessible to the EEPROM). |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 35 |
| Description: | • Hardware error |
| Causes: | CRC error of the EEPROM on the machine (EEPROM data error). |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 39 |
| Description: | • Hardware error |
| Causes: | Incorrect EEPROM |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 422 |
| Description: | Hardware error |
| Causes: | The DA setting for adjustment of the send part has reached the upper limit value when the test mode No. 705 (Paper sensor automatic adjustment) is performed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 423 |
| Description: | • Hardware error |
| Causes: | The DA setting for adjustment of the send part has reached the lower limit value when the test mode No. 705 (Paper sensor automatic adjustment) is performed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 5 |
| Description: | • Hardware error |
| Causes: | Hardware error |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 53 |
| Description: | • Hardware error |
| Causes: | Loading of the stored data of memory parameters (program, mode, user paper) has failed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 54 |
| Description: | • Hardware error |
| Causes: | Writing to the stored data of memory parameters (program, mode, user paper) has failed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 6 |
| Description: | • Hardware error |
| Causes: | FRAM checksum error |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 63 |
| Description: | • Hardware error |
| Causes: | The test mode setting data stored in the memory is out of the adjustment range. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 735 |
| Description: | • Hardware error |
| Causes: | 24V-OP is not turned ON. (Possible blown fuse at the 24V-OP system) |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 736 |
| Description: | • Hardware error |
| Causes: | The fuse chip on the Mechanical control PCB (CP2) has blown. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 777 |
| Description: | • Hardware error |
| Causes: | File creation has failed in the test mode No. 103 (storing of machine settings). |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 778 |
| Description: | • Hardware error |
| Causes: | Directory creation has failed in the test mode No. 103 (storing of machine settings). |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 787 |
| Description: | • Hardware error |
| Causes: | No file to restore has been found in the test mode No. 105 (restoration of machine settings). |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 788 |
| Description: | • Hardware error |
| Causes: | The file to restore has wrong machine type information when the test mode No. 105 (restoration of machine settings) is performed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 789 |
| Description: | • Hardware error |
| Causes: | The file to restore has wrong serial number when the test mode No. 105 (restoration of machine settings) is performed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 790 |
| Description: | • Hardware error |
| Causes: | The version of the file to restore is higher when the test mode No. 105 (restoration of machine settings) is performed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 791 |
| Description: | • Hardware error |
| Causes: | Rebooting error after the test mode No. 105 (restoration of machine settings) has been performed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 792 |
| Description: | • Hardware error |
| Causes: | No directory has been found in the test mode No. 105 (restoration of machine settings). |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 921 |
| Description: | • Hardware error |
| Causes: | USB controller chip is malfunctioning when PC and RG is connected via a USB cable. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 934 |
| Description: | • Hardware error |
| Causes: | Communication error between mechanical control PCB and RF tag PCB (detection on RF tag PCB side). |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 935 |
| Description: | • Hardware error |
| Causes: | Communication error between mechanical control PCB and RF tag PCB (detection on mechanical control PCB side). |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 937 |
| Description: | • Hardware error |
| Causes: | Serial number not specified |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 938 |
| Description: | • Hardware error |
| Causes: | Old FRAM program version |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 947 |
| Description: | • Hardware error |
| Causes: | 24V-A is not turned ON. (Possible blown fuse at the 24V-A system) |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 948 |
| Description: | • Hardware error |
| Causes: | 24V-B is not turned ON. (Possible blown fuse at the 24V-B system) |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 949 |
| Description: | • Hardware error |
| Causes: | 24V-A is not turned OFF. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 950 |
| Description: | • Hardware error |
| Causes: | 24V-B is not turned OFF. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 952 |
| Description: | • Hardware error |
| Causes: | Checksum error of NeoROSA PCB flash memory. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 953 |
| Description: | • Hardware error |
| Causes: | Data writing failure to NeoROSA PCB flash memory. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 960 |
| Description: | • Hardware error |
| Causes: | Data reading failure from NeoROSA PCB flash memory |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 961 |
| Description: | • Hardware error |
| Causes: | NeoROSA PCB flash memory is not used. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 97 |
| Description: | • Hardware error |
| Causes: | The test mode adjustment value stored in the print drum memory is out of the adjustment range. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 978 |
| Description: | • Hardware error |
| Causes: | At a time other than booting and wake-up, an erroneous power ON command is received from the mechanical control PCB side. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 979 |
| Description: | • Hardware error |
| Causes: | Setting value error in NeoROSA PCB flash memory settings. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 98 |
| Description: | • Hardware error |
| Causes: | The machine serial number information of the EEPROM on the machine does not match that on FRAM. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 983 |
| Description: | • Hardware error |
| Causes: | 24V-C is not turned ON. (Possible blown fuse at the 24V-C system) |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T98 984 |
| Description: | • Hardware error |
| Causes: | 24V-C is not turned OFF. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 1031 |
| Description: | • Software error |
| Causes: | Initializing the LVDS driver has failed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 1032 |
| Description: | • Software error |
| Causes: | Initializing the LCD driver has failed. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 1303 |
| Description: | • Software error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (on NeoROSA PCB side): Tag length error |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 14 |
| Description: | • Software error |
| Causes: | Sub microcomputer is detected to be physically damaged. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 150 |
| Description: | • Software error |
| Causes: | Scanning command or next original scanning start command is received from the machine during the occurrence of any of AF cover open, no original, and AF jam. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 154 |
| Description: | • Software error |
| Causes: | At the time of AF firmware download, a command outside the range of the regular sequence has been received. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 156 |
| Description: | • Software error |
| Causes: | At the time of AF firmware download, download data that is larger than the capacity of the program writing space has been received. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 159 |
| Description: | • Software error |
| Causes: | At the time of AF firmware download, download data checksum error has been detected. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 181 |
| Description: | • Software error |
| Causes: | Image processing time-out |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 185 |
| Description: | • Software error |
| Causes: | AF received an undefined command from the machine during initializing operation. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 186 |
| Description: | • Software error |
| Causes: | AF received an undefined command from the machine during scanning operation. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 187 |
| Description: | • Software error |
| Causes: | AF received an undefined command from the machine during downloading operation. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 188 |
| Description: | • Software error |
| Causes: | AF received an undefined command from the machine at a time other than during initializing, scanning, or downloading operation. * Error detection at AF side |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 3001 |
| Description: | • Software error |
| Causes: | Getting data from a USB memory has failed. Reduce the number of files saved in each folder in the USB memory to 250 or less. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 64 |
| Description: | • Hardware error |
| Causes: | Communication between NeoROSA and mechanical control PCB: An undefined command has been sent |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 65 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (01) on mechanical control PCB side: Complete number of bytes is not received |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 67 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (03) on mechanical control PCB side: RNK received |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 68 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (04) on mechanical control PCB side: NAK received three times |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 69 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (05) on mechanical control PCB side: ACK not responded |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 70 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (06) on mechanical control PCB side: Transmission prevented at NeoROSA |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 7028 |
| Description: | • Software error |
| Causes: | Replay from the machine has timed out when entering into the sleep mode. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 71 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (07) on mechanical control PCB side: Command sent while awaiting response |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 75 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (11) on NeoROSA PCB side: Complete number of bytes is not received |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 76 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (12) on NeoROSA PCB side: ACK not specified in sequence received |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 77 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (13) on NeoROSA PCB side: RNK received |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 78 |
| Description: | • Hardware error |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 79 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (15) on NeoROSA PCB side: ACK not responded |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 80 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (16) on NeoROSA PCB side: Transmission prevented at mechanical control PCB (CTS==1) |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 81 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (17) on NeoROSA PCB side: Mechanical control download mode sent by error |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 82 |
| Description: | • Hardware error |
| Causes: | Communication error between NeoROSA and mechanical control PCB (18) on NeoROSA PCB side: Mechanical CTS state 1 lasted for two seconds |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 923 |
| Description: | • Software error |
| Causes: | Firmware version incompatibility The firmware version for any of the main microcomputer, restoration loader, panel microcomputer, and analog microcomputer does not match the version combined in the downloaded package. * Compulsory download (TM7052) is required. |
| Remedy: | Switch the power OFF, then ON. |
| Error code: | T99 924 |
| Description: | • Software error |
| Causes: | AF firmware version incompatibility The connected AF has a firmware version that is not compatible with the package version for the machine. * Compulsory download (TM7052) is required. |
| Remedy: | Switch the power OFF, then ON. |
