Canon Color imageCLASS MF632Cdw
Рейтинг
Модули
103C - Internal Components 3 (230V, Wireless, Fax)
100G - External Covers (MF631Cn)
103B - Internal Components 3 (100/120V, Wireless, w/o Fax)
103F - Internal Components 3 (230V, w/o Wireless, w/o Fax)
101 - Internal Components 1
100D - External Covers (MF634Cdw)
103D - Internal Components 3 (120V, Wireless, Fax)
400B - Reader (ADF, 230V, LTN, AU, SG, HK, IN)
103E - Internal Components 3 (230V, Wireless, w/o Fax)
161A - Paper Feeder (Single Pass
160B - Reader / ADF (Single Side)
100E - External Covers (MF633Cdw)
160A - Reader / ADF (Single Pass ADF)
100F - External Covers (MF632Cdw)
162 - Reader / Copyboard
102C - Internal Components 2 (120V)
161B - Paper Feeder (Single Side ADF)
102B - Internal Components 2
Детали 162 - Reader / Copyboard
| Деталь: | CORE, FERRITE |
| Парткод: | FK2-8767-000 |
| Деталь: | CABLE, MADRID HDMI |
| Парткод: | FK4-4092-000 |
| Цена: | 5 700 ₽ |
| Деталь: | CABLE, FLAT |
| Парткод: | FL0-8148-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY SET |
| Парткод: | FM1-T024-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSY |
| Парткод: | FM1-Y966-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-6383-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-6384-000 |
| Деталь: | DENSITY DETECT SENSOR ASSY |
| Парткод: | RM2-5874-000 |
| Деталь: | INTERMEDIATE TRANS. BELT ASSY |
| Парткод: | RM2-5907-000 |
| Цена: | 8 000 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | MODULE, WLAN |
| Парткод: | FK4-1248-020 |
| Цена: | 12 200 ₽ |
| Деталь: | CABLE, FLAT |
| Парткод: | FL0-8151-000 |
| Цена: | 1 000 ₽ |
| Деталь: | SPEAKER |
| Парткод: | FK3-3944-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FL0-8150-000 |
| Деталь: | NCU PCB ASSEMBLY |
| Парткод: | FM1-X947-000 |
| Деталь: | CABLE, PSEUDO CI |
| Парткод: | FM1-X957-000 |
| Деталь: | OFFHOOK PCB ASSEMBLY |
| Парткод: | FM1-R867-000 |
| Деталь: | CABLE, OFF HOOK |
| Парткод: | FM1-X955-000 |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1835-000 |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | COVER, ARM, LEFT |
| Парткод: | FE8-3066-000 |
| Деталь: | COVER, ARM, CENTER |
| Парткод: | FE8-3068-000 |
| Деталь: | COVER, PANEL, REAR UPPER |
| Парткод: | FE8-3069-000 |
| Цена: | 470 ₽ |
| Деталь: | COVER, PANEL, REAR UNDER |
| Парткод: | FE8-3070-000 |
| Цена: | 700 ₽ |
| Деталь: | COVER, PANEL, LOWER |
| Парткод: | FE8-3071-000 |
| Цена: | 650 ₽ |
| Деталь: | COVER, FRONT, LEFT |
| Парткод: | FE8-3094-000 |
| Деталь: | COVER, FRONT, RIGHT |
| Парткод: | FE8-3095-000 |
| Деталь: | COVER, FRONT UPPER, RIGHT |
| Парткод: | FE8-3115-000 |
| Деталь: | COVER, ARM, RIGHT |
| Парткод: | FE8-3142-000 |
| Деталь: | COVER, PANEL, REAR |
| Парткод: | FE8-3262-000 |
| Деталь: | COVER ASSEMBLY, LEFT |
| Парткод: | FM1-N642-000 |
| Деталь: | SHEET, BLANKING |
| Парткод: | FL1-1416-000 |
| Деталь: | COVER ASSEMBLY, RIGHT |
| Парткод: | FM1-N643-000 |
| Деталь: | SHEET, HANDSET |
| Парткод: | FL1-0525-000 |
| Цена: | 800 ₽ |
| Деталь: | FRONT DOOR ASSY |
| Парткод: | FM1-N648-000 |
| Деталь: | COVER ASSEMBLY, TOP |
| Парткод: | FM1-N649-000 |
| Деталь: | DUPLEXING DOOR ASSY |
| Парткод: | FM1-N654-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-P234-000 |
| Деталь: | HINGE ASSEMBLY |
| Парткод: | FM1-P442-000 |
| Цена: | 2 600 ₽ |
| Деталь: | LABEL, NETWORK |
| Парткод: | FU2-1959-000 |
| Цена: | 270 ₽ |
| Деталь: | REAR DOOR ASSY |
| Парткод: | RM2-5580-000 |
| Деталь: | ROLLER, SECONDARY TRANSFER |
| Парткод: | RM2-5906-000 |
| Деталь: | LID, MODULAR |
| Парткод: | FE8-3017-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | CORE, FERRITE |
| Парткод: | FK2-8767-000 |
| Деталь: | CABLE, MADRID HDMI |
| Парткод: | FK4-4092-000 |
| Цена: | 5 700 ₽ |
| Деталь: | CABLE, FLAT |
| Парткод: | FL0-8148-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY |
| Парткод: | FM1-Y850-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSY |
| Парткод: | FM1-Y966-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-6383-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-6384-000 |
| Деталь: | DENSITY DETECT SENSOR ASSY |
| Парткод: | RM2-5874-000 |
| Деталь: | INTERMEDIATE TRANS. BELT ASSY |
| Парткод: | RM2-5907-000 |
| Цена: | 8 000 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | MODULE, WLAN |
| Парткод: | FK4-1248-020 |
| Цена: | 12 200 ₽ |
| Деталь: | CABLE, FLAT |
| Парткод: | FL0-8151-000 |
| Цена: | 1 000 ₽ |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | CORE, FERRITE |
| Парткод: | FK2-8767-000 |
| Деталь: | CABLE, MADRID HDMI |
| Парткод: | FK4-4092-000 |
| Цена: | 5 700 ₽ |
| Деталь: | CABLE, FLAT |
| Парткод: | FL0-8148-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY |
| Парткод: | FM1-Y851-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSY |
| Парткод: | FM1-Y966-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-6383-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-6384-000 |
| Деталь: | DENSITY DETECT SENSOR ASSY |
| Парткод: | RM2-5874-000 |
| Деталь: | INTERMEDIATE TRANS. BELT ASSY |
| Парткод: | RM2-5907-000 |
| Цена: | 8 000 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | DOOR, DUPLEXING, LEFT LOWER |
| Парткод: | FE8-3113-000 |
| Деталь: | PAPER PICK-UP ROLLER ASSY |
| Парткод: | RM2-5576-000 |
| Деталь: | FEED ROLLER ASSY |
| Парткод: | RM2-5577-000 |
| Деталь: | MULTI FEED TRAY ASSY |
| Парткод: | FM1-N653-000 |
| Деталь: | CASSETTE ASSY |
| Парткод: | FM1-N655-000 |
| Деталь: | LABEL, PRINT SET |
| Парткод: | FU2-1944-000 |
| Деталь: | PAPER PICK-UP GUIDE ASSY |
| Парткод: | RM2-5578-000 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | RM2-5881-000 |
| Деталь: | PRIORITY SLOT ASSY |
| Парткод: | RM2-5866-000 |
| Деталь: | DUPLEXING DRIVE ASSY |
| Парткод: | RM2-5872-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1835-000 |
| Деталь: | INTERNAL COMPONENTS 1 |
| Парткод: | NPN |
| Деталь: | COVER, ARM, LEFT |
| Парткод: | FE8-3066-000 |
| Деталь: | COVER, ARM, CENTER |
| Парткод: | FE8-3068-000 |
| Деталь: | COVER, PANEL, REAR UPPER |
| Парткод: | FE8-3069-000 |
| Цена: | 470 ₽ |
| Деталь: | COVER, PANEL, REAR UNDER |
| Парткод: | FE8-3070-000 |
| Цена: | 700 ₽ |
| Деталь: | COVER, PANEL, LOWER |
| Парткод: | FE8-3071-000 |
| Цена: | 650 ₽ |
| Деталь: | COVER, FRONT, LEFT |
| Парткод: | FE8-3094-000 |
| Деталь: | COVER, FRONT, RIGHT |
| Парткод: | FE8-3095-000 |
| Деталь: | COVER, FRONT UPPER, RIGHT |
| Парткод: | FE8-3115-000 |
| Деталь: | COVER, ARM, RIGHT |
| Парткод: | FE8-3142-000 |
| Деталь: | COVER, PANEL, REAR |
| Парткод: | FE8-3262-000 |
| Деталь: | COVER ASSEMBLY, LEFT |
| Парткод: | FM1-N642-000 |
| Деталь: | SHEET, BLANKING |
| Парткод: | FL1-1416-000 |
| Деталь: | COVER ASSEMBLY, RIGHT |
| Парткод: | FM1-N643-000 |
| Деталь: | SHEET, HANDSET |
| Парткод: | FL1-0525-000 |
| Цена: | 800 ₽ |
| Деталь: | FRONT DOOR ASSY |
| Парткод: | FM1-N648-000 |
| Деталь: | COVER ASSEMBLY, TOP |
| Парткод: | FM1-N649-000 |
| Деталь: | DUPLEXING DOOR ASSY |
| Парткод: | FM1-N654-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-P234-000 |
| Деталь: | HINGE ASSEMBLY |
| Парткод: | FM1-P442-000 |
| Цена: | 2 600 ₽ |
| Деталь: | LABEL, NETWORK |
| Парткод: | FU2-1959-000 |
| Цена: | 270 ₽ |
| Деталь: | REAR DOOR ASSY |
| Парткод: | RM2-5580-000 |
| Деталь: | ROLLER, SECONDARY TRANSFER |
| Парткод: | RM2-5906-000 |
| Деталь: | LABEL, MODULAR |
| Парткод: | FU2-1961-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | CORE, FERRITE |
| Парткод: | FK2-8767-000 |
| Деталь: | CABLE, MADRID HDMI |
| Парткод: | FK4-4092-000 |
| Цена: | 5 700 ₽ |
| Деталь: | CABLE, FLAT |
| Парткод: | FL0-8148-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY SET |
| Парткод: | FM1-T025-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSY |
| Парткод: | FM1-Y966-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-6383-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-6384-000 |
| Деталь: | DENSITY DETECT SENSOR ASSY |
| Парткод: | RM2-5874-000 |
| Деталь: | INTERMEDIATE TRANS. BELT ASSY |
| Парткод: | RM2-5907-000 |
| Цена: | 8 000 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | MODULE, WLAN |
| Парткод: | FK4-1248-020 |
| Цена: | 12 200 ₽ |
| Деталь: | CABLE, FLAT |
| Парткод: | FL0-8151-000 |
| Цена: | 1 000 ₽ |
| Деталь: | SPEAKER |
| Парткод: | FK3-3944-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FL0-8150-000 |
| Деталь: | NCU PCB ASSEMBLY |
| Парткод: | FM1-X947-000 |
| Деталь: | CABLE, PSEUDO CI |
| Парткод: | FM1-X957-000 |
| Деталь: | OFFHOOK PCB ASSEMBLY |
| Парткод: | FM1-R867-000 |
| Деталь: | CABLE, OFF HOOK |
| Парткод: | FM1-X955-000 |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1835-000 |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE8-3486-000 |
| Деталь: | SPACER, CIS |
| Парткод: | FE8-3479-000 |
| Деталь: | BELT, TIMING |
| Парткод: | FE8-3582-000 |
| Деталь: | CONTACT IMAGE SENSOR, FA106H-01 |
| Парткод: | FK4-4050-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-4051-000 |
| Деталь: | PULLEY UNIT |
| Парткод: | FL1-1412-000 |
| Деталь: | DC MOTOR ASSEMBLY |
| Парткод: | FM1-N718-000 |
| Деталь: | CABLE, READER SIGNAL, 1 |
| Парткод: | FM1-X905-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | COPY BOARD GLASS UNIT |
| Парткод: | FM1-N720-000 |
| Деталь: | LABEL, WIDTH SIZE |
| Парткод: | FE8-4192-000 |
| Деталь: | CONNECTING PCB ASSEMBLY |
| Парткод: | FM1-X900-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FE8-4198-000 |
| Деталь: | LABEL, GLASS CLEANING |
| Парткод: | FE8-4196-000 |
| Деталь: | READER ASSEMBLY |
| Парткод: | FM1-T598-000 |
| Деталь: | CORE, FERRITE |
| Парткод: | FK2-8767-000 |
| Деталь: | CABLE, MADRID HDMI |
| Парткод: | FK4-4092-000 |
| Цена: | 5 700 ₽ |
| Деталь: | CABLE, FLAT |
| Парткод: | FL0-8148-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY |
| Парткод: | FM1-Y849-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSY |
| Парткод: | FM1-Y966-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-6383-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-6384-000 |
| Деталь: | DENSITY DETECT SENSOR ASSY |
| Парткод: | RM2-5874-000 |
| Деталь: | INTERMEDIATE TRANS. BELT ASSY |
| Парткод: | RM2-5907-000 |
| Цена: | 8 000 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | MODULE, WLAN |
| Парткод: | FK4-1248-020 |
| Цена: | 12 200 ₽ |
| Деталь: | CABLE, FLAT |
| Парткод: | FL0-8151-000 |
| Цена: | 1 000 ₽ |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | GUIDE ASSEMBLY, UPPER |
| Парткод: | FM1-N704-000 |
| Деталь: | ROLLER |
| Парткод: | FE8-3440-000 |
| Деталь: | FLAG,SENSOR |
| Парткод: | FE8-3444-000 |
| Деталь: | STOPPER, DOCUMENT |
| Парткод: | FE8-3645-000 |
| Деталь: | GUIDE, UPPER |
| Парткод: | FL1-2518-000 |
| Деталь: | SEPARATION PAD ASSEMBLY |
| Парткод: | FM1-P580-000 |
| Деталь: | SHAFT, TRANSMISSION |
| Парткод: | FU2-1875-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-1904-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1905-000 |
| Деталь: | ROLLER, AUXILIARY |
| Парткод: | FU2-1906-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1922-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | PAPER FEEDER ASSEMBLY SET |
| Парткод: | FM1-T412-000 |
| Деталь: | GUIDE, PAPER DELIVERY |
| Парткод: | FE8-3446-000 |
| Деталь: | FLAG,SENSOR |
| Парткод: | FE8-3448-000 |
| Деталь: | BUSHING |
| Парткод: | FE8-3458-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE8-3459-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE8-3460-000 |
| Деталь: | RING, E |
| Парткод: | FE8-3636-000 |
| Деталь: | STOPPER, RATCHET SPRING |
| Парткод: | FE8-3655-000 |
| Деталь: | RATCHET, PAPER FEED ROLLER |
| Парткод: | FE8-3656-000 |
| Деталь: | LEVER, RELEASE |
| Парткод: | FE8-3657-000 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FL1-1367-000 |
| Деталь: | SHEET, GUIDE |
| Парткод: | FL1-1369-000 |
| Деталь: | ROLLER, PAPER DELIVERY |
| Парткод: | FM1-N407-000 |
| Деталь: | MOTOR DRIVE ASSY |
| Парткод: | FM1-N709-000 |
| Деталь: | CABLE, SIGNAL, DF, 2 |
| Парткод: | FM1-X902-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7207-006 |
| Деталь: | CABLE, SENSOR |
| Парткод: | FM1-X903-000 |
| Деталь: | CABLE, GROUNDING |
| Парткод: | FM1-X906-000 |
| Деталь: | GEAR, 67T |
| Парткод: | FU2-1867-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU2-1869-000 |
| Деталь: | GEAR, 38T |
| Парткод: | FU2-1870-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1902-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1907-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1908-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-4053-000 |
| Деталь: | HOLDER, CONTACT IMAGE SENSOR |
| Парткод: | FE8-3450-000 |
| Деталь: | GLASS HOLDER UNIT |
| Парткод: | FL1-2502-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1924-000 |
| Деталь: | CONTACT IMAGE SENSOR SET |
| Парткод: | FM1-T027-000 |
| Деталь: | SHEET, WHITE |
| Парткод: | FL1-4365-000 |
| Деталь: | PAPER FEEDER ASSEMBLY |
| Парткод: | NPN |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-4052-000 |
| Деталь: | SHEET, WHITE |
| Парткод: | FE8-3469-000 |
| Деталь: | COVER, REAR |
| Парткод: | FE8-3474-000 |
| Деталь: | COVER, FRONT |
| Парткод: | FE8-3475-000 |
| Деталь: | RING, E |
| Парткод: | FE8-3636-000 |
| Деталь: | BUSHING |
| Парткод: | FE8-3643-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FE8-3644-000 |
| Деталь: | PANEL, OPEN/CLOSE |
| Парткод: | FL1-2517-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM1-N703-000 |
| Деталь: | ROLLER, PICK-UP |
| Парткод: | FC8-9251-000 |
| Цена: | 440 ₽ |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL3-1023-000 |
| Цена: | 600 ₽ |
| Деталь: | GEAR, 23T |
| Парткод: | FU2-1865-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1902-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1903-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FE8-3462-000 |
| Деталь: | HINGE |
| Парткод: | FL1-1411 -000 |
| Деталь: | COVER, LOWER |
| Парткод: | FE8-3467-000 |
| Деталь: | CAP |
| Парткод: | FE8-4189-000 |
| Деталь: | PAPER FEED GUIDE ASSEMBLY |
| Парткод: | FM1-P584-000 |
| Деталь: | DOCUMENT TRAY ASSEMBLY |
| Парткод: | FM1-N711 -000 |
| Деталь: | LABEL, DOCUMENT SIZE |
| Парткод: | FE8-4191-000 |
| Деталь: | CABLE, SIGNAL, DF, 1 |
| Парткод: | FM1-X901-000 |
| Деталь: | CABLE, READER SIGNAL, 2 |
| Парткод: | FM1-X904-000 |
| Деталь: | CABLE, GROUNDING |
| Парткод: | FM1-X906-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | READER/ADF ASSEMBLY |
| Парткод: | NPN |
| Деталь: | COVER, ARM, LEFT |
| Парткод: | FE8-3066-000 |
| Деталь: | COVER, ARM, CENTER |
| Парткод: | FE8-3068-000 |
| Деталь: | COVER, PANEL, REAR UPPER |
| Парткод: | FE8-3069-000 |
| Цена: | 470 ₽ |
| Деталь: | COVER, PANEL, REAR UNDER |
| Парткод: | FE8-3070-000 |
| Цена: | 700 ₽ |
| Деталь: | COVER, PANEL, LOWER |
| Парткод: | FE8-3071-000 |
| Цена: | 650 ₽ |
| Деталь: | COVER, FRONT, LEFT |
| Парткод: | FE8-3094-000 |
| Деталь: | COVER, FRONT, RIGHT |
| Парткод: | FE8-3095-000 |
| Деталь: | COVER, FRONT UPPER, RIGHT |
| Парткод: | FE8-3115-000 |
| Деталь: | COVER, ARM, RIGHT |
| Парткод: | FE8-3142-000 |
| Деталь: | COVER, PANEL, REAR |
| Парткод: | FE8-3262-000 |
| Деталь: | COVER ASSEMBLY, LEFT |
| Парткод: | FM1-N642-000 |
| Деталь: | SHEET, BLANKING |
| Парткод: | FL1-1416-000 |
| Деталь: | COVER ASSEMBLY, RIGHT |
| Парткод: | FM1-N643-000 |
| Деталь: | SHEET, HANDSET |
| Парткод: | FL1-0525-000 |
| Цена: | 800 ₽ |
| Деталь: | FRONT DOOR ASSY |
| Парткод: | FM1-N648-000 |
| Деталь: | COVER ASSEMBLY, TOP |
| Парткод: | FM1-N649-000 |
| Деталь: | DUPLEXING DOOR ASSY |
| Парткод: | FM1-N654-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-P234-000 |
| Деталь: | HINGE ASSEMBLY |
| Парткод: | FM1-P442-000 |
| Цена: | 2 600 ₽ |
| Деталь: | LABEL, NETWORK |
| Парткод: | FU2-1959-000 |
| Цена: | 270 ₽ |
| Деталь: | REAR DOOR ASSY |
| Парткод: | RM2-5580-000 |
| Деталь: | ROLLER, SECONDARY TRANSFER |
| Парткод: | RM2-5906-000 |
| Деталь: | LID, MODULAR |
| Парткод: | FE8-3017-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-4057-000 |
| Деталь: | SHEET, WHITE |
| Парткод: | FE8-3469-000 |
| Деталь: | COVER, REAR |
| Парткод: | FE8-3474-000 |
| Деталь: | COVER, FRONT |
| Парткод: | FE8-3475-000 |
| Деталь: | RING, E |
| Парткод: | FE8-3636-000 |
| Деталь: | BUSHING |
| Парткод: | FE8-3643-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FE8-3644-000 |
| Деталь: | PANEL, OPEN/CLOSE |
| Парткод: | FL1-2517-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM1-N703-000 |
| Деталь: | ROLLER, PICK-UP |
| Парткод: | FC8-9251-000 |
| Цена: | 440 ₽ |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL3-1023-000 |
| Цена: | 600 ₽ |
| Деталь: | GEAR, 23T |
| Парткод: | FU2-1865-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1902-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1903-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FE8-3462-000 |
| Деталь: | HINGE |
| Парткод: | FL1-1411 -000 |
| Деталь: | COVER, LOWER |
| Парткод: | FE8-3467-000 |
| Деталь: | CAP |
| Парткод: | FE8-4189-000 |
| Деталь: | PAPER FEED GUIDE ASSEMBLY |
| Парткод: | FM1-P584-000 |
| Деталь: | DOCUMENT TRAY ASSEMBLY |
| Парткод: | FM1-N711 -000 |
| Деталь: | LABEL, DOCUMENT SIZE |
| Парткод: | FE8-4191-000 |
| Деталь: | CABLE, SIGNAL, DF, 1 |
| Парткод: | FM1-X901-000 |
| Деталь: | CABLE, READER SIGNAL, 2 |
| Парткод: | FM1-X904-000 |
| Деталь: | CABLE, GROUNDING |
| Парткод: | FM1-X906-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | READER/ADF ASSEMBLY |
| Парткод: | NPN |
| Деталь: | COVER, ARM, LEFT |
| Парткод: | FE8-3066-000 |
| Деталь: | COVER, ARM, CENTER |
| Парткод: | FE8-3068-000 |
| Деталь: | COVER, PANEL, REAR UPPER |
| Парткод: | FE8-3069-000 |
| Цена: | 470 ₽ |
| Деталь: | COVER, PANEL, REAR UNDER |
| Парткод: | FE8-3070-000 |
| Цена: | 700 ₽ |
| Деталь: | COVER, PANEL, LOWER |
| Парткод: | FE8-3071-000 |
| Цена: | 650 ₽ |
| Деталь: | COVER, FRONT, LEFT |
| Парткод: | FE8-3094-000 |
| Деталь: | COVER, FRONT, RIGHT |
| Парткод: | FE8-3095-000 |
| Деталь: | COVER, FRONT UPPER, RIGHT |
| Парткод: | FE8-3115-000 |
| Деталь: | COVER, ARM, RIGHT |
| Парткод: | FE8-3142-000 |
| Деталь: | COVER, PANEL, REAR |
| Парткод: | FE8-3262-000 |
| Деталь: | COVER ASSEMBLY, LEFT |
| Парткод: | FM1-N642-000 |
| Деталь: | SHEET, BLANKING |
| Парткод: | FL1-1416-000 |
| Деталь: | COVER ASSEMBLY, RIGHT |
| Парткод: | FM1-N643-000 |
| Деталь: | SHEET, HANDSET |
| Парткод: | FL1-0525-000 |
| Цена: | 800 ₽ |
| Деталь: | FRONT DOOR ASSY |
| Парткод: | FM1-N648-000 |
| Деталь: | COVER ASSEMBLY, TOP |
| Парткод: | FM1-N649-000 |
| Деталь: | DUPLEXING DOOR ASSY |
| Парткод: | FM1-N654-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-P234-000 |
| Деталь: | HINGE ASSEMBLY |
| Парткод: | FM1-P442-000 |
| Цена: | 2 600 ₽ |
| Деталь: | LABEL, NETWORK |
| Парткод: | FU2-1959-000 |
| Цена: | 270 ₽ |
| Деталь: | REAR DOOR ASSY |
| Парткод: | RM2-5580-000 |
| Деталь: | ROLLER, SECONDARY TRANSFER |
| Парткод: | RM2-5906-000 |
| Деталь: | LID, MODULAR |
| Парткод: | FE8-3017-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | COPYBOARD COVER ASSEMBLY |
| Парткод: | FM1-N701 -000 |
| Деталь: | CABLE, READER SIGNAL, 2 |
| Парткод: | FM1-X904-000 |
| Деталь: | CABLE, GROUNDING |
| Парткод: | FM1-X906-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-4052-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | READER/COPYBOARD ASSEMBLY |
| Парткод: | NPN |
| Деталь: | POWER SUPPLY SWITCH ASSY |
| Парткод: | FM1-N656-000 |
| Деталь: | PLATE, USB, GROUNDING |
| Парткод: | FE8-0014-000 |
| Цена: | 950 ₽ |
| Деталь: | USB RELAY PCB ASSEMBLY |
| Парткод: | FM1-R870-000 |
| Цена: | 3 400 ₽ |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM1-N684-000 |
| Деталь: | PAPER DELIVERY SENSOR ASSY |
| Парткод: | FM1-N695-000 |
| Деталь: | L.V. POWER SUPPLY PCB ASSY |
| Парткод: | FM1-Y968-000 |
| Деталь: | CARTRIDGE TRAY ASSY |
| Парткод: | RM2-5871-000 |
| Деталь: | MAIN MOTOR ASSY |
| Парткод: | RM2-7407-000 |
| Деталь: | FIXING MOTOR ASSY |
| Парткод: | RM2-7409-000 |
| Деталь: | FAN |
| Парткод: | RK2-6425-000 |
| Деталь: | MICROSWITCH |
| Парткод: | RK2-0534-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1835-000 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
| Деталь: | GUIDE ASSEMBLY, UPPER |
| Парткод: | FM1-N704-000 |
| Деталь: | ROLLER |
| Парткод: | FE8-3440-000 |
| Деталь: | FLAG,SENSOR |
| Парткод: | FE8-3444-000 |
| Деталь: | STOPPER, DOCUMENT |
| Парткод: | FE8-3645-000 |
| Деталь: | GUIDE, UPPER |
| Парткод: | FL1-2518-000 |
| Деталь: | SEPARATION PAD ASSEMBLY |
| Парткод: | FM1-P580-000 |
| Деталь: | SHAFT, TRANSMISSION |
| Парткод: | FU2-1875-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-1904-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1905-000 |
| Деталь: | ROLLER, AUXILIARY |
| Парткод: | FU2-1906-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1922-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | PAPER FEEDER ASSEMBLY |
| Парткод: | FM1-N706-000 |
| Деталь: | GUIDE, PAPER DELIVERY |
| Парткод: | FE8-3446-000 |
| Деталь: | FLAG,SENSOR |
| Парткод: | FE8-3448-000 |
| Деталь: | BUSHING |
| Парткод: | FE8-3458-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE8-3459-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE8-3460-000 |
| Деталь: | RING, E |
| Парткод: | FE8-3636-000 |
| Деталь: | STOPPER, RATCHET SPRING |
| Парткод: | FE8-3655-000 |
| Деталь: | RATCHET, PAPER FEED ROLLER |
| Парткод: | FE8-3656-000 |
| Деталь: | LEVER, RELEASE |
| Парткод: | FE8-3657-000 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FL1-1367-000 |
| Деталь: | SHEET, GUIDE |
| Парткод: | FL1-1369-000 |
| Деталь: | ROLLER, PAPER DELIVERY |
| Парткод: | FM1-N407-000 |
| Деталь: | MOTOR DRIVE ASSY |
| Парткод: | FM1-N709-000 |
| Деталь: | CABLE, SIGNAL, DF, 2 |
| Парткод: | FM1-X902-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7207-006 |
| Деталь: | CABLE, SENSOR |
| Парткод: | FM1-X903-000 |
| Деталь: | CABLE, GROUNDING |
| Парткод: | FM1-X906-000 |
| Деталь: | GEAR, 67T |
| Парткод: | FU2-1867-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU2-1869-000 |
| Деталь: | GEAR, 38T |
| Парткод: | FU2-1870-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1902-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1907-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1908-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1923-000 |
| Деталь: | HOLDER UNIT |
| Парткод: | FM1-N708-000 |
| Деталь: | PAPER FEEDER ASSEMBLY |
| Парткод: | NPN |
| Деталь: | POWER SUPPLY SWITCH ASSY |
| Парткод: | FM1-N656-000 |
| Деталь: | PLATE, USB, GROUNDING |
| Парткод: | FE8-0014-000 |
| Цена: | 950 ₽ |
| Деталь: | USB RELAY PCB ASSEMBLY |
| Парткод: | FM1-R870-000 |
| Цена: | 3 400 ₽ |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM1-N685-000 |
| Деталь: | PAPER DELIVERY SENSOR ASSY |
| Парткод: | FM1-N695-000 |
| Деталь: | L.V. POWER SUPPLY PCB ASSY |
| Парткод: | FM1-Y969-000 |
| Деталь: | CARTRIDGE TRAY ASSY |
| Парткод: | RM2-5871-000 |
| Деталь: | MAIN MOTOR ASSY |
| Парткод: | RM2-7407-000 |
| Деталь: | FIXING MOTOR ASSY |
| Парткод: | RM2-7409-000 |
| Деталь: | FAN |
| Парткод: | RK2-6425-000 |
| Деталь: | MICROSWITCH |
| Парткод: | RK2-0534-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1835-000 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
Коды ошибок
0001
0002
0021
0094
0104
0105
014C
0248
0250
025C
02A4
1014
1017
1054
1055
1056
1057
1095
10D5
1118
1158
1198
11D8
E000-0000
E001-0000
E001-0001
E003-0000
E003-0001
E004-0000
E012-0000
E012-0001
E014-0000
E014-0001
E015-0000
E015-0001
E015-0002
E020-0000
E021-1000
E021-1001
E021-1002
E021-1003
E021-2000
E021-2001
E021-2002
E021-2003
E052-0000
E066-0000
E078-0000
E100-0000
E100-0001
E100-0002
E100-0003
E110-0000
E194-0000
E196-0000
E198-0000
E202-0001
E202-0002
E246-0000
E247-0000
E302-0001
E302-0002
E350-0000
E354-0000
E355-0000
E355-0004
E355-0005
E732-0000
E733-0000
E743-0000
E805-0005
E806-0000
E808-0000
E840-0000
Описание
| Error code: | 0001 |
| Display: | Main motor failure CODE (001) Turn power off, on |
| Description: | Main Motor Failure The Main Motor lock signal remains HIGH for a predetermined consecutive period of time while the Main Motor remains energized. |
| Causes: | • Main Motor, PL9.1.6 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check the Engine Control Board connector P/J8. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Check the Main Motor for proper positioning. Is the motor engaged with the gears? Go to step 3. Reseat the motor drive properly. If the problem persists, go to step 3. 3 Check the operation of the Main Motor. Is the motor faulty? Replace the motor. If the problem persists, go to step 4. Go to step 4. 4 On the Engine Control Board, check P/J2 at pins 1, 5, and 7 for +24V. Are the voltages present? Go to step 5. Go to step 6. 5 Replace the Engine Control Board. Does the problem persist? Go to step 5. Complete. 6 Replace the Power Supply. Complete. |
| Error code: | 0002 |
| Description: | Disorder of communication with Sub CPU This occurs when the Sub CPU is not detected after turning on the machine |
| Causes: | Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. |
| Remedy: | Check cable connection between Main Board and Servo Board. Check cable connection between Main Board and Heater Board. Check the other cable connections of Servo Board Heater Board replacement Servo Board replacement Main Board replacement Flexible cable replacement |
| Error code: | 0021 |
| Description: | Other |
| Causes: | Document End Sensor |
| Remedy: | SR10 ADF Pickup Feed Area |
| Error code: | 0094 |
| Display: | Trans. roll failure CODE (0094) Turn power off, on |
| Description: | Transfer Roll Failure Possible causes: • The 2nd Image Transfer Retraction Position Sensor(PS3) is not activated (retracted position) within a given period of time after the retraction sequence of the 2nd transfer roller has been started. • The 2nd Image Transfer Retraction Position Sensor is not deactivated (pressed position) within a given period of time after the pressure sequence of the 2nd transfer roller has been started. |
| Causes: | • 2nd Image Transfer Retraction Position Sensor (PS3), PL4.0.9 • 2nd Image Transfer Retraction Position Solenoid (SD4), PL7.2.23 • Main Motor, PL9.1.6 • Engine Control Board, PL13.0.20 |
| Remedy: | 1 Check the Main Motor connector CN37. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Check the Main Motor for proper drive coupling and correct as necessary. Does the problem persist? Go to step 3. Complete. 3 Check the 2nd Image Transfer Retraction Position Solenoid connector CN5. Is the connector seated properly? Go to step 4. Reseat the connector. If the problem persists, go to step 4. 4 Check the 2nd Image Transfer Retraction Position Solenoid for proper drive coupling and correct as necessary. Does the problem persist? Go to step 5. Complete. 5 Check the 2nd Image Transfer Retraction Position Sensor control signal for a voltage change at P/J12-3 on the Engine Control Board. Is the signal operating correctly? Go to step 6. Replace the Engine Control Board. If the problem persists, go to step 6. 6 Replace the 2nd Image Transfer Retraction Position Solenoid. Does the problem persist? Go to step 7. Complete. 7 Replace the 2nd Image Transfer Retraction Position Sensor. Complete. |
| Error code: | 0104 |
| Description: | Even though the machine carries out the regular movement, the output of Capping Sensor does not reach the expected value. |
| Causes: | Capping Motor does not work correctly or is broken. Capping Unit does not work correctly or is broken. Capping Sensor does not work correctly or is broken. |
| Remedy: | Capping Motor replacement Capping unit replacement Capping Sensor replacement Flexible Cable replacement |
| Error code: | 0105 |
| Description: | Tool Carriage Connection Error |
| Causes: | Fault of Tool Carriage Connection Loose of Connection Part Fault of the Limit Position Initialize value Limit Sensor does not work correctly or is broken. |
| Remedy: | Check the mechanical Backlash or loose with the Tool Carriage part. Connection Part Replacement Limit Position Initialize |
| Error code: | 014C |
| Description: | Media Full Sensor Delay PS204 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor |
| Error code: | 0248 |
| Description: | Top Sensor/Media full sensor/Fixing Delivery Sensor PS204/205/915 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor |
| Error code: | 0250 |
| Description: | Head device has detected a problem. |
| Causes: | Cut-line or short-circuit of cable and Flexible cable. The head is broken. |
| Remedy: | Pull out and insert the flexible cables again. Replace the flexible cable. Replace the head. |
| Error code: | 025C |
| Description: | Top Sensor/Media Full Sensor PS204/205 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor |
| Error code: | 02A4 |
| Description: | Duplex Re-pickup Assembly Jam1 |
| Causes: | Duplex Re-pickup Sensor |
| Remedy: | SR22 Duplex Re-pickup Assembly |
| Error code: | 1014 |
| Description: | Top Sensor/Media Full Sensor PS204/205 |
| Causes: | Cassette Feed Sensor |
| Error code: | 1017 |
| Description: | Power ON Jam 4 |
| Causes: | Cassette Feed Sensor |
| Remedy: | SR31 Cassette2 |
| Error code: | 1054 |
| Display: | PaprWidth Mismatch |
| Description: | Top Sensor/Media full sensor/Fixing Delivery Sensor PS204/205/915 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor |
| Error code: | 1055 |
| Description: | Power ON Jam 2 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor |
| Remedy: | SR604/SR607/SR608 Registration Area to Cartridge Cartridge to Fixing Roller Area |
| Error code: | 1056 |
| Description: | Power ON Jam 3 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor |
| Remedy: | SR604/SR607/SR608 Registration Area to Cartridge Cartridge to Fixing Roller Area |
| Error code: | 1057 |
| Description: | Power ON Jam 4 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor |
| Remedy: | SR1/SR3/SR4/SR22 Registration Area to Delivery Area |
| Error code: | 1095 |
| Description: | Power ON Jam 2 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor |
| Remedy: | SR604/SR607/SR608 Duplex Re-pickup Assembly |
| Error code: | 10D5 |
| Description: | Power ON Jam 2 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor |
| Remedy: | SR604/SR607/SR608 Registration Area to Delivery Area Duplex Re-pickup Assembly |
| Error code: | 1118 |
| Description: | Door open jam (SR202, SR203, SR209, SW2, SW3) (Related to Printer Unit) |
| Causes: | Registration sensor/Multi-purpose Tray Paper Sensor/Cassette Feed Sensor |
| Error code: | 1158 |
| Description: | Top Sensor/Media full sensor/Fixing Delivery Sensor PS204/205/915 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor |
| Error code: | 1198 |
| Description: | Top Sensor/Media full sensor/Fixing Delivery Sensor PS204/205/915 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor |
| Error code: | 11D8 |
| Description: | Duplex Feed Sensor PS201 |
| Causes: | Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor |
| Error code: | E000-0000 |
| Description: | Startup error The temperature detected by the main or sub thermistor does not rise to the specified value during startup control. |
| Causes: | The detection temperature of the main thermistor did not increase after start of the power distribution to the heater. |
| Remedy: | - Check the fixing film connector. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0000 |
| Description: | Abnormally high temperature (detected by main thermistor) The main thermistor detected an abnormally high temperature 235 deg C) during temperature control |
| Causes: | The main thermistor detected a temperature of higher than 255 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0001 |
| Description: | Abnormally high temperature (detected by sub thermistor) The sub thermistor detected an abnormally high temperature (300 deg C) during temperature control. |
| Causes: | The sub thermistor detected a temperature of higher than 290 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0000 |
| Description: | Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The main thermistor detected a temperature of lower than 120 degree C for more than 1 second when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0001 |
| Description: | Abnormally low temperature (detected by sub thermistor) After the temperature detected by the sub thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The sub thermistor detected a temperature of lower than 80 degree C for more than 2 seconds when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E004-0000 |
| Description: | Fixing power supply drive circuit error |
| Causes: | 43 to 57Hz could not be detected continuously for more than 5 seconds when zero cross detection started. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the DC Controller Board. (2) Replace the Fixing Assembly. |
| Error code: | E012-0000 |
| Description: | Error in ITB motor activation. |
| Causes: | The cycle of ITB motor speed detection signal does not move in the specified cycle after ITB motor drive is started. Cause Failure in ITB motor, failure in DC controller PCB |
| Remedy: | - Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB |
| Error code: | E012-0001 |
| Description: | Error in ITB motor activation. |
| Causes: | If the ITB motor speed detection signal comes off the specified cycle after it turned once to the specified cycle. Cause Failure in ITB motor, failure in DC controller PCB. |
| Remedy: | - Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB |
| Error code: | E014-0000 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor startup error The target speed was not reached within a specified time after startup of the motor. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E014-0001 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor rotation error The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E015-0000 |
| Description: | Developing disengagement motor failure |
| Causes: | Developing disengagement motor failure The standard flag was not detected even when driving was performed for 1000ms after rotation of the motor. The standard flag was not detected even when driving was performed for 8000ms at the time of switching from the full-color position to "all disengagement". The standard flag was not detected even when driving was performed for 3000ms at the time of switching from the monochrome position to "all disengagement". |
| Remedy: | Reconnect the connector J518 of the developing disengagement motor, the connector J1005 on the driver PCB, and the connector J91 on the DC controller PCB. Check the condition of the developing disengagement sensor in the sensor monitor mode. If a failure is found, replace the developing disengagement sensor assembly. Execute the developing assembly engagement/disengagement drive test in the actuator drive mode. If the developing assembly does not perform engagement/disengagement, replace the developing disengagement motor. |
| Error code: | E015-0001 |
| Description: | Cassette 1 lift up motor error |
| Causes: | Cassette 1 lift up motor error |
| Remedy: | Reconnect the connector J151 on the DC controller PCB and the relay connector J742. Check the cassette media stack surface sensor in the sensor monitor mode. If a failure is found, replace the lifter drive unit. Replace the lifter drive unit. |
| Error code: | E015-0002 |
| Description: | Cassette 2 lift up motor error |
| Causes: | Cassette 2 lift up motor error |
| Remedy: | Reconnect the connector J2003 on the paper feeder driver PCB and the relay connector J702. Check the paper feeder media stack surface sensor in the sensor monitor mode. If a failure is found, replace the pickup unit. Reconnect the connector J2006 on the paper feeder driver PCB. Replace the lifter drive unit. |
| Error code: | E020-0000 |
| Description: | Density sensor failure warning |
| Error code: | E021-1000 |
| Description: | Yellow Developing Motor rotation error |
| Causes: | It was judged that the Developing Motor did not rotate. |
| Remedy: | 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1) |
| Error code: | E021-1001 |
| Description: | Magenta Developing Motor rotation error |
| Causes: | It was judged that the Developing Motor did not rotate. |
| Remedy: | 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1). |
| Error code: | E021-1002 |
| Description: | Cyan Developing Motor rotation error |
| Causes: | It was judged that the Developing Motor did not rotate. |
| Remedy: | 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1). |
| Error code: | E021-1003 |
| Description: | Error in developing motor |
| Causes: | Developing motor does not rotate. Cause Failure in developing motor, failure in DC controller PCB. |
| Remedy: | - Check the connectors of developing motor, DC controller PCB - Replace the developing motor - Replace the DC controller PCB |
| Error code: | E021-2000 |
| Description: | Error in startup of the Yellow Developing Motor |
| Causes: | Revolution of the Developing Motor did not reach the specified value. |
| Remedy: | 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1). |
| Error code: | E021-2001 |
| Description: | Error in startup of the Magenta Developing Motor |
| Causes: | Revolution of the Developing Motor did not reach the specified value. |
| Remedy: | 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1). |
| Error code: | E021-2002 |
| Description: | Error in startup of the Cyan Developing Motor |
| Causes: | Revolution of the Developing Motor did not reach the specified value. |
| Remedy: | 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1). |
| Error code: | E021-2003 |
| Description: | Error in developing motor |
| Causes: | The cycle of developing motor speed detection signal does not move in the specified cycle after developing motor drive is started. Cause Failure in developing motor, failure in DC controller PCB |
| Remedy: | - Check the connectors of developing motor, DC controller PCB - Replace the developing motor - Replace the DC controller PCB |
| Error code: | E052-0000 |
| Description: | Erroneous connection to duplex unit Disconnection of the duplex unit was detected after power-on, detection of normal connection to the duplex unit, and start of communication. |
| Causes: | Failed to detect 2-sided unit Cause: improper 2-sided unit connection |
| Remedy: | - Check the connectors of the duplex unit and DC controller PCB. - Replace the duplex controller PCB. - Replace the DC controller PCB. |
| Error code: | E066-0000 |
| Description: | Environment sensor failure |
| Causes: | Environment sensor failure |
| Remedy: | Replace the environment sensor. |
| Error code: | E078-0000 |
| Description: | Error in primary transfer disengagement. |
| Causes: | Primary transfer disengagement mechanism did not work properly. Cause Disengagement mechanism error, ITB Tension Sensor error, Pickup Motorerror, DC Controller PCB error |
| Remedy: | - Check the disengagement mechanism. - Check the connectors of the ITB Tension - - Sensor, Pickup Motor and the DC Controller PCB (J167, J202, J160, J201, J140). - Replace the ITB Tension Sensor. - Replace the Pickup Motor. - Replace the DC Controller PCB. |
| Error code: | E100-0000 |
| Description: | BD detection PCB failure The BD detection PCB is faulty. |
| Causes: | Yellow optical assembly failure |
| Remedy: | - Check the connector of the BD detection PCB. - Replace the laser scanner unit. - Replace the DC controller PCB. |
| Error code: | E100-0001 |
| Description: | Error detection on any of scanner motor, laser unit, and BD detection at scanner area. |
| Causes: | Magenta optical assembly failure |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Laser Scanner Unit. (2) Replace the DC Controller Board. |
| Error code: | E100-0002 |
| Description: | Optical assembly error (Laser) |
| Causes: | Cyan optical assembly failure |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E100-0003 |
| Description: | Optical assembly error (Laser) |
| Causes: | Black optical assembly failure |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E110-0000 |
| Description: | Optical assembly error (Scanner motor) |
| Causes: | Optical assembly error (Scanner motor initial operation failure) |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E194-0000 |
| Description: | Error in CPR sensor |
| Causes: | If CPR sensor is judged error. Cause Soiling in density detection sensor, failure in density detection sensor, failure in DC controller PCB, failure in toner cartridge. |
| Remedy: | - Check the connector of DC controller PCB - Replace the ITB unit - Replace the DC controller PCB - Replace the toner cartridge |
| Error code: | E196-0000 |
| Description: | Invalid RFU execution requested |
| Causes: | D-con update for the host machine or the optional cassette is not completed. |
| Error code: | E198-0000 |
| Description: | DC controller memory failure |
| Causes: | A checksum failure is found in the block where specific information of the DC controller PCB is saved. A communication error occurred when reading the specific information of the DC controller PCB from the NVRAM at power-on. |
| Remedy: | If the failure cannot be removed by turning the power OFF/ON, replace the DC controller PCB. |
| Error code: | E202-0001 |
| Description: | Reader HP sensor fault |
| Causes: | Reader HP outward fault The CCD unit moves backward, but does not move to the home position. |
| Remedy: | - Replace reader HP sensor. - Replace reader motor sensor. - Replace reader unit. |
| Error code: | E202-0002 |
| Description: | Contact Sensor HP error, Failure in return |
| Causes: | Reader HP homeward fault - Replace reader unit. The CCD unit moves forward, but does not move to the home position. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board. |
| Error code: | E246-0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E247-0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E302-0001 |
| Description: | Shading error |
| Causes: | When the light intensity is below the reference level at shading |
| Remedy: | 1. Disconnect and then connect the Flexible Cable. 2. Replace the Flexible Cable. 3. Replace the CIS Unit. 4. Replace the Main Controller PCB (PCB2). |
| Error code: | E302-0002 |
| Description: | Shading error |
| Causes: | Image sampling for shading was not completed. |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Check the connection of the harness. 3. Replace the Main Controller PCB. 4. Replace the Reader Unit. |
| Error code: | E350-0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E354-0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E355-0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E355-0004 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E355-0005 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E732-0000 |
| Description: | Scanner communication error. |
| Causes: | Scanner communication error |
| Remedy: | 1. Install the set of the controller firmware. 2.Replace the Main Controller PCB (UN30). |
| Error code: | E733-0000 |
| Description: | Erroneous communication between controller and printer Cannot communicate with the printer at startup. |
| Causes: | Printer communication error (communication error at initial communication and negotiation packet error) |
| Remedy: | - Check the connectors of the DC controller PCB and image processor PCB for normal connection. - Check the power supply of the printer (Check whether initialization is performed at startup). - Replace the DC controller PCB or image processor PCB. |
| Error code: | E743-0000 |
| Description: | Error in main controller communication An error in reading of/writing to the Flash ROM in the Main Controller occurred. |
| Causes: | Software sequence error |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB. |
| Error code: | E805-0005 |
| Description: | Error in duplex cooling fan |
| Causes: | Duplex cooling fan can not rotate the specified number of rotations. Cause Failure in duplex cooling fan, failure in DC controller PCB |
| Remedy: | - Check the connectors of duplex cooling fan and DC controller PCB - Replace the duplex cooling fan |
| Error code: | E806-0000 |
| Description: | Fan Motor cannot rotate at specified revolution speed. |
| Causes: | Fixing / fixing power supply cooling fan does not rotate in the specified rotation speed. Cause: Problem in fixing / fixing power supply cooling fan / DC controller PCB |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Main Fan Unit. (2) Replace the DC Controller Board. |
| Error code: | E808-0000 |
| Description: | Fixing drive circuit failure - The heater does not turn on. - A fixing drive motor failure was detected. |
| Causes: | Printer detected failure in low-voltage power supply Cause: Failure in low-voltage power supply, problem in DC controller PCB |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the fixing drive motor. - Replace the DC controller PCB. - Replace the power supply PCB. |
| Error code: | E840-0000 |
| Description: | Pressure release mechanism failure |
| Causes: | The target pressure position was not reached even when 3.5 seconds (approximately 1.5 rotation of the cam) elapsed after start of the fixing motor reverse rotation. |
| Remedy: | Check the gears and detection flags related to fixing pressure release mechanism. Replace the fixing pressure release sensor (PS9). Replace the fixing motor. Replace the fixing assembly. |
