Samsung CLX-8640ND

Общие характеристики
Технология печати	лазерная
Тип	лазерный/светодиодный
Сканер
Тип устройства	МФУ
Копир
Факс
Макс. формат	A4
Размещение	настольный
Печать фотографий
Цветность печати	цветная
Телефон
Число страниц в месяц	200 000
Область применения	большой офис
Прямая печать
Двусторонняя печать
Печать без полей
Пигментные чернила
Количество цветов	4
Макс, разрешение для ч/б печати
По X	600
По Y	600
Скорость ч/б печати
A4	38
Время выхода первого отпечатка
Ч/б	14
Цветн,	13
Время выхода первой копии	9
Макс, количество копий за цикл	999
Значение масштаба
Минимальное	0,25
Максимальное	4
Макс, разрешение (ч/б)
По Y	600
По X	600
Отправка изображения по e-mail
Стандарт TWAIN
Стандарт WIA
Макс. формат оригинала	A4
Слайд-адаптер
Тип датчика сканера	ПЗС (CCD)
Тип сканера	планшетный/протяжный
Макс, размер сканирования
По X	216
По Y	356
Разрешение сканера
По Y (улучшенное)	4 800
По Х (улучшенное)	4 800
По Х	600
Количество картриджей	4
Печать на:
Карточках
Пленках
Этикетках
Матовой бумаге
Конвертах
Глянцевой бумаге
Фотобумаге
CD/DVD
Рулоне
Цветной
АОН
Спикерфон
Стандарт DECT
Проводная трубка
Беспроводная трубка
Автоответчик
Caller ID
Языки управления
PostScript 3
PostScript
PCL 6
PDF
PCL 5c
PostScript 2
Емкость лотка ручной подачи	100
Подача бумаги
Максимальная	2 180
Стандартная	620
Степлер
Сортер
Брошюровщик
USB
Ethernet (RJ-45)
Bluetooth
Wi-Fi
FireWire (IEEE 1394)
Инфракрасный порт
Устройство для чтения карт памяти
RS-232
LPT
Объем памяти	1 024
Макс, объем памяти	2 048
Емкость жесткого диска	160
Частота процессора	1 000
Процессор	Chorus4N Dual Core
Экран
Диагональ дисплея	7
Работа от аккумулятора
Поддержка ОС
Windows
Mac OS
Linux
Потребляемая мощность
При работе	1 000
Уровень шума
При работе	56

Error code:	2448, S1-2449
Display:	System Failure: #S1-2433 . Call for service HDD System Failure # : Call for service
Description:	System memory is corrupted. / Unexpected S/W error has occurred.
Remedy:	1) Enter the SVC(tech) mode. Select “System Recovery” in Service Function menu. 2) Execute the hard disk format and firmware re-installation. 3) If the problem persists, replace the HDD(JC59-00035A).

Error code:	5232, S2-5233, S2-5234
Display:	Failed to adjust the OPC Feed forward control
Description:	OPC feed forward control failure has occurred.
Remedy:	1) Replace the ITB unit.

Error code:	A1-1211, A1-1212, A1-1213
Display:	Motor Failure: #. Turn off then on. Call for service if the problem persists.
Description:	Fuser motor operation is abnormal.
Remedy:	• A1-1211 : Fuser motor is stopped but machine recognizes it as operational. • A1-1212 : Fuser motor is not operated for print-job. • A1-1213 : Fuser motor is operating but machine recognizes status as "Stopped". 1) Turn the machine off. Check if there are any foreign substances or paper around fuser unit. 2) Check if the fuser unit is damaged. If yes, replace the fuser unit. 3) Remove the rear cover after removing 7 screws. 4) Check if the Fuser motor connectors are connected correctly. 5) If the connection is OK, turn the machine on. Enter SVC mode. Select fuser motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 109-0030) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM • If the checked result is normal, replace the motor(JC31-00123B). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board(JC44-00150B(220V) / JC44-00149B(110V)). - If the control signal is abnormal, replace the main board(JC92-02516A). b) If the motor is operational, • Check the Pin Num 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness.

Error code:	A1-1311, A1-1312, A1-1313
Display:	Motor Failure: # Turn off then on. Call for service if the problem persists.
Description:	Pick-up motor operation is abnormal.
Remedy:	• A1-1311 : Pick-up motor is stopped but machine recognizes it as operational. • A1-1312 : Pick-up motor is not operated for print-job. • A1-1313 : Pick-up motor is operating but machine recognizes status as "Stopped". 1) Turn the machine off. Remove the cassette. Check if there are any foreign substances or paper around cassettes. 2) Check if the fuser unit is damaged. If yes, replace the fuser unit. 3) Remove the rear cover after removing 7 screws. 4) Check if the Pick-up motor connectors are connected correctly. 5) If the connection is OK, turn the machine on. Enter SVC mode. Select pick up motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100-0340) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the motor(JC31-00123B). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board(JC44-00150B(220V) / JC44-00149B(110V)). - If the control signal is abnormal, replace the main board(JC92-02516A). b) If the motor is operational, • Check the Pin Num 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness.

Error code:	A1-1611, A1-1612, A1-1613
Display:	Motor Failure: #A1-1611. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-1612. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-1613. Turn off then on. Call for service if the problem persists.
Description:	Motor Failure: #A1-1611. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-1612. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-1613. Turn off then on. Call for service if the problem persists.
Causes:	ITB motor operation is abnormal • A1–1611 : ITB motor is stopped but machine recognizes it as operational. • A1–1612 : ITB motor is not operated for print-job. • A1–1613 : ITB motor is operating but machine recognizes status as "Stopped".
Remedy:	1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Open the side cover. Remove the ITB unit 4) Check if the ITB motor connector is connected correctly. 5) If the connection is OK, turn the machine on. Enter SVC mode. Select motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100–0450) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the motor(JC31-00123B). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board (JC44-00100C (220V) / JC44-00093C (110V)). - If the control signal is abnormal, replace the main board(JC92-02742A). b) If the motor is operational, • Check the Pin Num 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness.

Error code:	A1-2211, A1-2212, A1-2213
Display:	Motor Failure: #A1-2211. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2212. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2213. Turn off then on. Call for service if the problem persists
Description:	Motor Failure: #A1-2211. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2212. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2213. Turn off then on. Call for service if the problem persists
Causes:	Yellow OPC motor operation is abnormal. • A1–2211 : Yellow OPC motor is stopped but machine recognizes it as operational. • A1–2212 : Yellow OPC motor is not operated for print-job. • A1–2213 : Yellow OPC motor is operating but machine recognizes status as "Stopped".
Remedy:	1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Open the side cover. Check if there are any foreign substances or paper around yellow drum drive unit. 3) Remove the rear cover. 4) Check if the yellow OPC motor connector is connected correctly. 5) If the connection is OK, turn the machine on. Enter SVC mode. Select the yellow OPC motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100–0041) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the motor(JC31-00123B). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board (JC44-00100C (220V) / JC44-00093C (110V)). - If the control signal is abnormal, replace the main board(JC92-02742A). b) If the motor is operational, • Check the Pin Num 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness.

Error code:	A1-2311, A1-2312, A1-2313
Display:	Motor Failure: #A1-2311. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2312. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2313. Turn off then on. Call for service if the problem persists
Description:	Motor Failure: #A1-2311. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2312. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2313. Turn off then on. Call for service if the problem persists
Causes:	Magenta OPC motor operation is abnormal. • A1–2311 : Magenta OPC motor is stopped but machine recognizes it as operational. • A1–2312 : Magenta OPC motor is not operated for print-job. • A1–2313 : Magenta OPC motor is operating but machine recognizes status as "Stopped".
Remedy:	1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Open the side cover. Check if there are any foreign substances or paper around magenta drum drive unit. 3) Remove the rear cover. 4) Check if the magenta OPC motor connector is connected correctly. 5) If the connection is OK, turn the machine on. Enter SVC mode. Select the magenta OPC motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100–0042) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the motor(JC31-00123B). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board (JC44-00100C (220V) / JC44-00093C (110V)). - If the control signal is abnormal, replace the main board(JC92-02742A). b) If the motor is operational, • Check the Pin Num 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness.

Error code:	A1-2411, A1-2412, A1-2413
Display:	Motor Failure: #A1-2411. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2412. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2413. Turn off then on. Call for service if the problem persists
Description:	Motor Failure: #A1-2411. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2412. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2413. Turn off then on. Call for service if the problem persists
Causes:	Cyan OPC motor operation is abnormal. • A1–2411 : Cyan OPC motor is stopped but machine recognizes it as operational. • A1–2412 : Cyan OPC motor is not operated for print-job. • A1–2413 : Cyan OPC motor is operating but machine recognizes status as "Stopped".
Remedy:	1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Open the side cover. Check if there are any foreign substances or paper around cyan drum drive unit. 3) Remove the rear cover. 4) Check if the cyan OPC motor connector is connected correctly. 5) If the connection is OK, turn the machine on. Enter SVC mode. Select the cyan OPC motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100–0043) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the motor(JC31-00123B). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board (JC44-00100C (220V) / JC44-00093C (110V)). - If the control signal is abnormal, replace the main board(JC92-02742A). b) If the motor is operational, • Check the Pin Num 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness.

Error code:	A1-2511, A1-2512, A1-2513
Display:	Motor Failure: #A1-2511. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2512. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2513. Turn off then on. Call for service if the problem persists
Description:	Motor Failure: #A1-2511. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2512. Turn off then on. Call for service if the problem persists Motor Failure: #A1-2513. Turn off then on. Call for service if the problem persists
Causes:	Black OPC motor operation is abnormal. • A1–2511 : Black OPC motor is stopped but machine recognizes it as operational. • A1–2512 : Black OPC motor is not operated for print-job. • A1–2513 : Black OPC motor is operating but machine recognizes status as "Stopped".
Remedy:	1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Open the side cover. Check if there are any foreign substances or paper around black drum drive unit. 3) Remove the rear cover. 4) Check if the black OPC motor connector is connected correctly. 5) If the connection is OK, turn the machine on. Enter SVC mode. Select the black OPC motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100–0044) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the motor(JC31-00123B). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board (JC44-00100C (220V) / JC44-00093C (110V)). - If the control signal is abnormal, replace the main board(JC92-02742A). b) If the motor is operational, • Check the Pin Num 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness.

Error code:	A1-4310
Display:	Motor Failure: #A1-4310. Turn off then on. Call for service if the problem persists
Description:	Actuator Motor Failure : #A1-4310. Call for service if the problem persists.
Causes:	The motor for ITB unit does not operate normally.
Remedy:	1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Remove the right cover. 3) Check if the connection between main board and the main drive unit are correct. 4) If the connection is OK, replace the main drive unit. 5) If the problem persists, replace the main board.

Error code:	A1-5211, A1-5212, A1-5213
Display:	Motor Failure: #. Turn off then on. Call for service if the problem persists
Description:	Yellow toner is not supplied normally.
Remedy:	• A1-5211 : Yellow toner supply motor is not operational but toner is supplied. • A1-5212 : Yellow toner supply motor does not operate. • A1-5213 : Yellow toner supply is stopped during operation. 1) Open the front cover. If the yellow toner pipe is blocked, open it. 2) Turn the machine off then on. If the error persists, check the following steps. 3) Enter SVC mode. Select the yellow toner supply motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 111-0000 : Toner Dispense Motor Yellow 4) If the motor is not operational, a) Remove the rear cover after removing 7 screws. b) Remove the main board shield. Measure the yellow motor power with DVM. i) If 24V power is generated, replace the yellow toner supply motor(JC31-00159A). ii) If 24V power is not generated, • Measure the 24V power on the SMPS board. If the SMPS board(JC44-00150B (220V) / JC44-00149B (110V)) is defective, replace it. • If the SMPS board is normal, replace the main board(JC92-02516A).

Error code:	A1-5311, A1-5312, A1-5313
Display:	Motor Failure: #. Turn off then on. Call for service if the problem persists
Description:	Magenta toner is not supplied normally.
Remedy:	• A1-5311 : Magenta toner supply motor is not operational but toner is supplied. • A1-5312 : Magenta toner supply motor does not operate. • A1-5313 : Magenta toner supply is stopped during operation. 1) Open the front cover. If the magenta toner pipe is blocked, open it. 2) Turn the machine off then on. If the error persists, check the following steps. 3) Enter SVC mode. Select the magenta toner supply motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 111-0010 : Toner Dispense Motor Magenta 4) If the motor is not operational, a) Remove the rear cover after removing 7 screws. b) Remove the main board shield. Measure the magenta motor power with DVM. i) If 24V power is generated, replace the magenta toner supply motor(JC31-00159A). ii) If 24V power is not generated, • Measure the 24V power on the SMPS board. If the SMPS board(JC44-00150B (220V) / JC44-00149B (110V)) is defective, replace it. • If the SMPS board is normal, replace the main board(JC92-02516A).

Error code:	A1-5411, A1-5412, A1-5413
Display:	Motor Failure: #. Turn off then on. Call for service if the problem persists
Description:	Cyan toner is not supplied normally.
Remedy:	• A1-5411 : Cyan toner supply motor is not operational but toner is supplied. • A1-5412 : Cyan toner supply motor does not operate. • A1-5413 : Cyan toner supply is stopped during operation. 1) Open the front cover. If the cyan toner pipe is blocked, open it. 2) Turn the machine off then on. If the error persists, check the following steps. 3) Enter SVC mode. Select the cyan toner supply motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 111-0020 : Toner Dispense Motor Cyan 4) If the motor is not operational, a) Remove the rear cover after removing 7 screws. b) Remove the main board shield. Measure the cyan motor power with DVM. i) If 24V power is generated, replace the cyan toner supply motor(JC31-00159A). ii) If 24V power is not generated, • Measure the 24V power on the SMPS board. If the SMPS board(JC44-00150B (220V) / JC44-00149B (110V)) is defective, replace it. • If the SMPS board is normal, replace the main board(JC92-02516A).

Error code:	A1-5511, A1-5512, A1-5513
Display:	Motor Failure: #. Turn off then on. Call for service if the problem persists
Description:	Black toner is not supplied normally.
Remedy:	• A1-5511 : Black toner supply motor is not operational but toner is supplied. • A1-5512 : Black toner supply motor does not operate. • A1-5513 : Black toner supply is stopped during operation. 1) Open the front cover. If the cyan toner pipe is blocked, open it. 2) Turn the machine off then on. If the error persists, check the following steps. 3) Enter SVC mode. Select the black toner supply motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 111-0030 : Toner Dispense Motor Black 4) If the motor is not operational, a) Remove the rear cover after removing 7 screws. b) Remove the main board shield. Measure the black motor power with DVM. i) If 24V power is generated, replace the black toner supply motor(JC31-00159A). ii) If 24V power is not generated, • Measure the 24V power on the SMPS board. If the SMPS board(JC44-00150B (220V) / JC44-00149B (110V)) is defective, replace it. • If the SMPS board is normal, replace the main board(JC92-02516A).

Error code:	A3-2110, A3-2113, A3-2210
Display:	ID control has failed. Check the CTD sensor(A3-2110) The CTD sensor is dirty. Please clean it with soft cloth or paper(A3-2113) ID control has failed. Check the CTD sensor(A3-2210)
Description:	CTD sensor is defective or CTD sensor calibration is abnormal.
Remedy:	1) Open the side cover. 2) Open the ACR module. 3) Move the shutter to the right manually. 4) Close the side cover. 5) Check if the CTD sensor window is contaminated. If yes, clean the window with soft cloth. 6) If the problem persists, replace the CTD sensor(JC32-00012A and JC32-00014A).

Error code:	A3-3111, A3-3112
Display:	Sensor Failure: #. Turn off then on. Call for service if the problem persists.
Description:	Sensor Failure: #A3-3111. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3112. Turn off then on. Call for service if the problem persists
Causes:	The NC sensor in the fuser unit is defective. / The sensor signal is abnormal due to a defective harness. • A3–3111 : Center NC sensor is in short status. • A3–3112 : Center NC sensor is in open status. • A3–3113 : Side NC sensor is in short status. • A3–3114 : Side NC sensor is in open status.
Remedy:	1) Enter SVC mode. Execute sensor test to check the sensor operation. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 109-0000 : Fuser Temperature A • 109-0010 : Fuser Temperature B 3) Measure the resistance value of the thermistor (1404-001453). If the measured value is out of 307KΩ~430KΩ @25℃, replace the thermistor. 4) Install the fuser unit after replacing the thermistor. 5) If the error persists, replace the fuser unit (JC91-01157A(220V) / JC91–01158A (110V)). 6) If the error persists after replacing fuser unit, replace the main board(JC92–02742A).

Error code:	A3-3113, A3-3114
Display:	Sensor Failure: #. Turn off then on. Call for service if the problem persists.
Description:	Sensor Failure: #A3-3113. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3114. Turn off then on. Call for service if the problem persists
Causes:	The NC sensor in the fuser unit is defective. / The sensor signal is abnormal due to a defective harness. • A3–3111 : Center NC sensor is in short status. • A3–3112 : Center NC sensor is in open status. • A3–3113 : Side NC sensor is in short status. • A3–3114 : Side NC sensor is in open status.
Remedy:	1) Enter SVC mode. Execute sensor test to check the sensor operation. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 109-0000 : Fuser Temperature A • 109-0010 : Fuser Temperature B 3) Measure the resistance value of the thermistor (1404-001453). If the measured value is out of 307KΩ~430KΩ @25℃, replace the thermistor. 4) Install the fuser unit after replacing the thermistor. 5) If the error persists, replace the fuser unit (JC91-01157A(220V) / JC91–01158A (110V)). 6) If the error persists after replacing fuser unit, replace the main board(JC92–02742A).

Error code:	A3-3210, A3-3211, A3-3212
Display:	Sensor Failure: #. Turn off then on. Call for service if the problem persists.
Description:	Sensor Failure: #A3-3210. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3211. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3212. Turn off then on. Call for service if the problem persists
Causes:	Inner temperature sensor is defective. • A3–3210 : Inner temperature sensor value is abnormal. • A3–3211 : Inner temperature sensor is in short status. • A3–3212 : Inner temperature sensor is in open status.
Remedy:	1) Open the side cover. Check the connection. • If the connection is OK, replace the photo sensor (1404-001417). 2) If the sensor is normal, replace the main board(JC92-02742A).

Error code:	A3-3310, A3-3311, A3-3312
Display:	Sensor Failure: #A3-3310. Turn off then on. Call for service if the problem persists. Actuator Fan Failure #: Turn off then on.
Description:	Sensor Failure: #A3-3310. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3311. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3312. Turn off then on. Call for service if the problem persists
Causes:	Outer temperature/humidity sensor is defective. • A3–3310 / A3–3311 / A3–3312 : Temperature function is abnormal. • A3–3410 / A3–3411 / A3–3412 : Humidity function is abnormal.
Remedy:	1) Remove the left cover. Unplug and reconnect the sensor harness. If the error persists, replace the sensor(JC93-00486A). 2) If the harness and sensor are normal, replace the main board (JC92-02742A).

Error code:	A3-3410, A3-3411, A3-3412
Display:	Sensor Failure: #A3-3310. Turn off then on. Call for service if the problem persists. Actuator Fan Failure #: Turn off then on.
Description:	Sensor Failure: #A3-3410. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3411. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3412. Turn off then on. Call for service if the problem persists
Causes:	Outer temperature/humidity sensor is defective. • A3–3310 / A3–3311 / A3–3312 : Temperature function is abnormal. • A3–3410 / A3–3411 / A3–3412 : Humidity function is abnormal.
Remedy:	1) Remove the left cover. Unplug and reconnect the sensor harness. If the error persists, replace the sensor(JC93-00486A). 2) If the harness and sensor are normal, replace the main board (JC92-02742A).

Error code:	A3-4114
Display:	The ACR sensor is dirty. Please clean it with soft cloth or paper(A3-4114)
Description:	ACR(CTD) sensor is defective or ACR(CTD) sensor calibration is abnormal.
Remedy:	1) Open the side cover. 2) Open the ACR module. 3) Move the shutter to the right manually. 4) Close the side cover. 5) Check if the CTD sensor window is contaminated. If yes, clean the window with soft cloth. 6) If the problem persists, replace the CTD sensor(JC32-00012A and JC32-00014A).

Error code:	A4-1117, A4-1118
Display:	Lamp Failure: #. Open the door, then close it. Call for service if the problem persists.
Description:	Eraser Lamp is off.
Remedy:	1) Open the front cover and side cover. Remove the waste toner container and imaging units. 2) Enter SVC mode. Execute Lamp test. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 107-0160 : Erase Lamp1 • 107-0161 : Erase Lamp2 3) Check if the Lamp is on. Remove the rear cover after removing 7 screws. 4) Check the erase Lamp harness connection. (JC39-01733A / JC39-01734A) 5) If the Lamp Assy or harness is defective, replace it. (Harness : JC39-01733A / Erase Lamp Assy : JC98-01979A) 6) If the Lamp Assy and harness are normal, replace the main board(JC92-02516A)

Error code:	C1-2110
Display:	Prepare new yellow toner cartridge.
Description:	Prepare new yellow toner cartridge.
Causes:	Yellow toner is almost empty.
Remedy:	1) Order new yellow toner cartridge because toner cartridge with level of “Low” will be exhausted soon.

Error code:	C1-2120, C1-2120, C1-2140
Display:	Replace with new yellow toner cartridge
Description:	The yellow toner cartridge is at the end of its life.
Remedy:	1) Open the front cover. 2) Remove the yellow toner cartridge. 3) Install the new yellow toner cartridge. 4) Close the front cover.

Error code:	C1-2410
Display:	Install yellow toner cartridge.
Description:	The yellow toner cartridge is not installed.
Remedy:	1) Open the front cover. Check if the yellow toner cartridge is installed. 2) Remove and reinstall the yellow toner cartridge. 3) If the problem persists, check if the toner cartridge modular jack is contaminated or deformed. 4) Replace the yellow toner cartridge with new one.

Error code:	C1-2510, C1-2513
Display:	Yellow toner cartridge is not compatible. Check users guide. New yellow toner cartridge is not compatible. Check users guide
Description:	Yellow toner cartridge is not compatible.
Remedy:	1) Replace the yellow toner cartridge with a new one.

Error code:	C1-2711, C1-2712
Display:	Toner Cartridge Failure: #. Call for service
Description:	Yellow toner cartridge is not installed. Install it. Shake yellow toner cartridge.
Causes:	The yellow toner cartridge is not installed. / The CRUM data is not detected.
Remedy:	1) Open the front cover. Check if the yellow toner cartridge is installed. 2) Remove and reinstall the yellow toner cartridge. 3) If the problem persists, check if the toner cartridge modular jack is contaminated or deformed. 4) Replace the yellow toner cartridge with a new one.

Error code:	C1-3110
Display:	Prepare new magenta toner cartridge.
Description:	Prepare new magenta toner cartridge.
Causes:	Magenta toner is almost empty.
Remedy:	1) Order new magenta toner cartridge because toner cartridge with level of “Low” will be exhausted soon.

Error code:	C1-3120, C1-3124, C1-3140
Display:	Replace with new magenta toner cartridge.
Description:	The magenta toner cartridge is at the end of its life.
Remedy:	1) Open the front cover. 2) Remove the magenta toner cartridge. 3) Install the new magenta toner cartridge. 4) Close the front cover.

Error code:	C1-3410
Display:	Install magenta toner cartridge.
Description:	The magenta toner cartridge is not installed.
Remedy:	1) Open the front cover. Check if the magenta toner cartridge is installed. 2) Remove and reinstall the magenta toner cartridge. 3) If the problem persists, check if the toner cartridge modular jack is contaminated or deformed. 4) Replace the magenta toner cartridge with new one.

Error code:	C1-3510, C1-3513
Display:	Magenta toner cartridge is not compatible. Check users guide. New magenta toner cartridge is not compatible. Check users guide
Description:	Magenta toner cartridge is not compatible.
Remedy:	1) Replace the magenta toner cartridge with a new one.

Error code:	C1-3711, C1-3712
Display:	Toner Cartridge Failure: #. Call for service
Description:	Magenta toner cartridge is not installed. Install it. Shake magenta toner cartridge.
Causes:	The magenta toner cartridge is not installed. / The CRUM data is not detected.
Remedy:	1) Open the front cover. Check if the magenta toner cartridge is installed. 2) Remove and reinstall the magenta toner cartridge. 3) If the problem persists, check if the toner cartridge modular jack is contaminated or deformed. 4) Replace the magenta toner cartridge with a new one.

Error code:	C1-4110
Display:	Prepare new cyan toner cartridge.
Description:	Prepare new cyan toner cartridge.
Causes:	Cyan toner is almost empty.
Remedy:	1) Order new cyan toner cartridge because toner cartridge with level of “Low” will be exhausted soon.

Error code:	C1-4120, C1-4124, C1-4140
Display:	Replace with new magenta toner cartridge.
Description:	The cyan toner cartridge is at the end of its life.
Remedy:	1) Open the front cover. 2) Remove the cyan toner cartridge. 3) Install the new cyan toner cartridge. 4) Close the front cover.

Error code:	C1-4410
Display:	Install cyan toner cartridge.
Description:	The cyan toner cartridge is not installed.
Remedy:	1) Open the front cover. Check if the cyan toner cartridge is installed. 2) Remove and reinstall the cyan toner cartridge. 3) If the problem persists, check if the toner cartridge modular jack is contaminated or deformed. 4) Replace the cyan toner cartridge with new one.

Error code:	C1-4510, C1-4513
Display:	Cyan toner cartridge is not compatible. Check users guide. New cyan toner cartridge is not compatible. Check users guide
Description:	Cyan toner cartridge is not compatible.
Remedy:	1) Replace the cyan toner cartridge with a new one.

Error code:	C1-4711, C1-4712
Display:	Toner Cartridge Failure: #. Call for service
Description:	The data of CRUM is not detected.
Remedy:	1) Open the front cover. Check if the cyan toner cartridge is installed. 2) Remove and reinstall the cyan toner cartridge. 3) If the problem persists, check if the toner cartridge modular jack is contaminated or deformed. 4) Replace the cyan toner cartridge with new one.

Error code:	C1-5110
Display:	Prepare new black toner cartridge.
Description:	Prepare new black toner cartridge.
Causes:	Black toner is almost empty.
Remedy:	1) Order new black toner cartridge because toner cartridge with level of “Low” will be exhausted soon.

Error code:	C1-5120, C1-5124, C1-5140
Display:	Replace with new black toner cartridge
Description:	The black toner cartridge is at the end of its life.
Remedy:	1) Open the front cover. 2) Remove the black toner cartridge. 3) Install the new black toner cartridge. 4) Close the front cover.

Error code:	C1-5410
Display:	Install cyan toner cartridge.
Description:	The black toner cartridge is not installed.
Remedy:	1) Open the front cover. Check if the black toner cartridge is installed. 2) Remove and reinstall the black toner cartridge. 3) If the problem persists, check if the toner cartridge modular jack is contaminated or deformed. 4) Replace the black toner cartridge with new one.

Error code:	C1-5510, C1-5513
Display:	Black toner cartridge is not compatible. Check users guide. New black toner cartridge is not compatible. Check users guide
Description:	Black toner cartridge is not compatible.
Remedy:	1) Replace the black toner cartridge with a new one.

Error code:	C1-5711, C1-5712
Display:	Call for Service Error: #C1-5711 Call for Service Error: #C1-5712 Call for Service
Description:	Error: #C1-5711 Call for Service Error: #C1-5712 Call for Service
Causes:	CRUM chip of the toner cartridge is defective.
Remedy:	1) Check if the toner cartridge is installed properly. Turn the machine off then on. 2) If the problem persists, check that the CRUM contact area is contaminated. Clean it. 3) If the problem persists, replace the toner cartridge with new one.

Error code:	C3-2110
Display:	Prepare new yellow imaging unit
Description:	Prepare new yellow imaging unit
Causes:	Yellow drum unit has almost reached the end of its life.
Remedy:	1) Order new yellow drum unit because drum unit with level of “Low” will be exhausted soon.

Error code:	C3-2120
Display:	Replace with new yellow imaging unit
Description:	Yellow drum unit is at the end of its life.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Open the side cover. 4) Remove the yellow drum unit. 5) Install the new yellow drum unit. 6) Install the waste toner container. 7) Close the front cover.

Error code:	C3-2410, C3-2414, C3-2510
Display:	Install yellow imaging unit. Yellow Imaging Unit Failure: #C3-2414. Install yellow imaging unit again Yellow imaging unit is not compatible. Check users guide
Description:	Yellow drum unit is not installed. / The machine can’t read the charger resistance value from the yellow drum unit. / Yellow drum unit is not compatible.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Open the side cover. 4) Remove the yellow drum unit. 5) Install the new yellow drum unit. 6) Install the waste toner container. 7) Close the front cover.

Error code:	C3-2711, C3-2712
Display:	Imaging unit Failure: #. Call for service.
Description:	The data of CRUM is not detected.
Remedy:	1) Open the front cover and side cover. 2) Remove the waste toner container. 3) Check if the yellow drum is installed. 4) Remove and reinstall the yellow drum unit. 5) If the problem persists, check that the drum modular jack is contaminated or deformed. 6) Replace the yellow drum unit with new one.

Error code:	C3-3110
Display:	Prepare new magenta imaging unit
Description:	Prepare new magenta imaging unit
Causes:	Magenta drum unit has almost reached the end of its life.
Remedy:	1) Order new magenta drum unit because drum unit with level of “Low” will be exhausted soon.

Error code:	C3-3120
Display:	Replace with new magenta imaging unit
Description:	Magenta drum unit is at the end of its life.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Open the side cover. 4) Remove the magenta drum unit. 5) Install the new magenta drum unit. 6) Install the waste toner container. 7) Close the front cover.

Error code:	C3-3410, C3-3414, C3-3510
Display:	Install magenta imaging unit. Magenta Imaging Unit Failure: #C3-3414. Install magenta imaging unit again Magenta imaging unit is not compatible. Check users guide
Description:	Magenta drum unit is not installed. / The machine can’t read the charger resistance value from the magenta drum unit. / Magenta drum unit is not compatible
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Open the side cover. 4) Remove the magenta drum unit. 5) Install the new magenta drum unit. 6) Install the waste toner container. 7) Close the front cover.

Error code:	C3-3711, C3-3712
Display:	Imaging unit Failure: #. Call for service.
Description:	The data of CRUM is not detected.
Remedy:	1) Open the front cover and side cover. 2) Remove the waste toner container. 3) Check if the magenta drum is installed. 4) Remove and reinstall the magenta drum unit. 5) If the problem persists, check that the drum modular jack is contaminated or deformed. 6) Replace the magenta drum unit with new one.

Error code:	C3-4110
Display:	Prepare new cyan imaging unit
Description:	Prepare new cyan imaging unit
Causes:	Cyan drum unit has almost reached the end of its life.
Remedy:	1) Order new cyan drum unit because drum unit with level of “Low” will be exhausted soon.

Error code:	C3-4120
Display:	Replace with new cyan imaging unit
Description:	Cyan drum unit is at the end of its life.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Open the side cover. 4) Remove the cyan drum unit. 5) Install the new cyan drum unit. 6) Install the waste toner container. 7) Close the front cover.

Error code:	C3-4410, C3-4414, C3-4510
Display:	Install cyan imaging unit. Cyan Imaging Unit Failure: #C3-4414. Install cyan imaging unit again Cyan imaging unit is not compatible. Check users guide
Description:	Cyan drum unit is not installed. / The machine can’t read the charger resistance value from the cyan drum unit. / Cyan drum unit is not compatible.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Open the side cover. 4) Remove the cyan drum unit. 5) Install the new cyan drum unit. 6) Install the waste toner container. 7) Close the front cover.

Error code:	C3-4711, C3-4712
Display:	Imaging unit Failure: #. Call for service.
Description:	The data of CRUM is not detected.
Remedy:	1) Open the front cover and side cover. 2) Remove the waste toner container. 3) Check if the cyan drum is installed. 4) Remove and reinstall the cyan drum unit. 5) If the problem persists, check that the drum modular jack is contaminated or deformed. 6) Replace the cyan drum unit with new one.

Error code:	C3-5110
Display:	Prepare new cyan imaging unit
Description:	Prepare new cyan imaging unit
Causes:	Black drum unit has almost reached the end of its life.
Remedy:	1) Order new black drum unit because drum unit with level of “Low” will be exhausted soon.

Error code:	C3-5120
Display:	Replace with new black imaging unit
Description:	Black drum unit is at the end of its life.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Open the side cover. 4) Remove the black drum unit. 5) Install the new black drum unit. 6) Install the waste toner container. 7) Close the front cover.

Error code:	C3-5410, C3-5414, C3-5510
Display:	Install black imaging unit. Black Imaging Unit Failure: #C3-5414. Install black imaging unit again Black imaging unit is not compatible. Check users guide
Description:	Black drum unit is not installed. / The machine can’t read the charger resistance value from the black drum unit. / Black drum unit is not compatible.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Open the side cover. 4) Remove the black drum unit. 5) Install the new black drum unit. 6) Install the waste toner container. 7) Close the front cover.

Error code:	C3-5711, C3-5712
Display:	Imaging unit Failure: #. Call for service.
Description:	The data of CRUM is not detected.
Remedy:	1) Open the front cover and side cover. 2) Remove the waste toner container. 3) Check if the black drum is installed. 4) Remove and reinstall the black drum unit. 5) If the problem persists, check that the drum modular jack is contaminated or deformed. 6) Replace the black drum unit with new one.

Error code:	C5-1110, C5-1120
Display:	Prepare new Transfer belt Replace new Transfer belt
Description:	Prepare new Transfer belt Replace new Transfer belt
Causes:	The ITB Unit is at the end of its life.
Remedy:	1) Print the supply information report. Check the life remaining of the ITB unit. 2) If its life is at the end, turn the machine off and replace the ITB unit with new one.

Error code:	C5-1620, C5-1630
Display:	ITB Unit Failure: #C5-1620/1630/1640/1650. Turn off then on
Description:	The resistance value for 1st transfer roller is abnormal.
Remedy:	1) Turn the machine off. Open the side cover. 2) Replace the ITB Unit (JC96-06322A). 3) Close the side cover. Turn the machine on. 4) If the problem persists, replace the HVPS board. 5) Enter SVC mode. To enter SVC mode, press 1,2,3 number keys simultaneously. When the password dialog box appears, enter “1934” and press the “OK” button. 6) Select “TRANSFER” (INFORMATION > Supply Status > Field Replacement Unit > TRANSFER) 7) Select “ITB”. The “RESET” button will be activated. Click “RESET” to clear the ITB count. 8) Exit SVC mode by pushing the home button.

Error code:	C5-1640, C5-1650
Display:	ITB Unit Failure: #C5-1620/1630/1640/1650. Turn off then on
Description:	The resistance value for 1st transfer roller is abnormal.
Remedy:	1) Turn the machine off. Open the side cover. 2) Replace the ITB Unit (JC96-06322A). 3) Close the side cover. Turn the machine on. 4) If the problem persists, replace the HVPS board. 5) Enter SVC mode. To enter SVC mode, press 1,2,3 number keys simultaneously. When the password dialog box appears, enter “1934” and press the “OK” button. 6) Select “TRANSFER” (INFORMATION > Supply Status > Field Replacement Unit > TRANSFER) 7) Select “ITB”. The “RESET” button will be activated. Click “RESET” to clear the ITB count. 8) Exit SVC mode by pushing the home button.

Error code:	C6-1110, C6-1120
Display:	Prepare new fuser unit. Replace with new fuser unit.
Description:	Replace Fuser Soon Replace new Fuser unit
Causes:	The fuser unit is at the end of its life.
Remedy:	1) Print the supply information report. Check the life remaining of the fuser unit. 2) If its life is at the end, turn the machine off and replace the fuser unit with new one.

Error code:	C6-1310
Display:	Fuser unit is not installed. Install it
Description:	Fuser unit is not installed. Install it.
Causes:	The fuser unit is not installed or fuser unit connector is not connected properly.
Remedy:	1) Turn the machine off then on. 2) If the problem persists, turn the machine off again. 3) Open the side cover. Check if the fuser unit is installed. If not, install the fuser unit. 4) If the fuser unit is installed, remove it. 5) Check if the fuser draw connector (JC39–01677A) is broken or defective. 6) Install the fuser unit. 7) If the problem persists, replace the fuser unit(JC91-01157A (220V) /JC91-01158A (110V)).

Error code:	C7-1110, C7-1130
Display:	Waste toner container is almost full. Order new one. Waste toner container is full. Replace it.
Description:	Waste toner container is almost full. Order new one. Waste toner container is full. Replace it.
Causes:	The life of the waste toner container expires soon or has expired.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. Install a new waste toner container. 3) Close the front cover.

Error code:	C7-1310
Display:	Install waste toner container.
Description:	The waste toner container is full.
Remedy:	Install the waste toner container. If the waste toner container is already installed, remove and reinstall it.

Error code:	C8-2110, C8-2125
Display:	Prepare new yellow developer unit Replace with new yellow developer unit. Call for service
Description:	The life of the yellow developer unit expires soon or has expired.
Remedy:	1) If its life is at the end, turn the machine off and replace the developer unit with new one.

Error code:	C8-2210, C8-2310, C8-2313
Display:	Yellow Developer Failure: #C8-2210. Turn off then on Yellow Developer Failure: #C8-2310. Install yellow developer unit again Yellow Developer Failure: #C8-2313. Turn off then on. Please call for service if the problem persists
Description:	Yellow Developer Failure: #C8-2210. Turn off then on Yellow Developer Failure: #C8-2310. Install yellow developer unit again Yellow Developer Failure: #C8-2313. Turn off then on. Please call for service if the problem persists
Causes:	The yellow developer unit has a problem with toner supply or sensor calibration.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Check if the toner supply pipe is blocked. If it is closed, open it. 4) Install the waste toner container. Close the front cover. 5) Turn the machine off then on. 6) If the problem persists, remove and reinstall the yellow developer unit. 7) If the problem persists, replace the yellow developer unit.

Error code:	C8-2410
Display:	Yellow developer unit is not installed. Install it
Description:	The yellow developer unit is not installed.
Remedy:	1) Open the front cover. 2) Check if all developer unit is installed. Remove and re-install the developer unit.

Error code:	C8-3110, C8-3125
Display:	Prepare new magenta developer unit Replace with new magenta developer unit. Call for service
Description:	The life of the magenta developer unit expires soon or has expired.
Remedy:	1) If its life is at the end, turn the machine off and replace the developer unit with new one.

Error code:	C8-3210, C8-3310, C8-3313
Display:	Magenta Developer Failure: #C8-3210. Turn off then on Magenta Developer Failure: #C8-3310. Install magenta developer unit again Magenta Developer Failure: #C8-3313. Turn off then on. Please call for service if the problem persists
Description:	Magenta Developer Failure: #C8-3210. Turn off then on Magenta Developer Failure: #C8-3310. Install magenta developer unit again Magenta Developer Failure: #C8-3313. Turn off then on. Please call for service if the problem persists
Causes:	The magenta developer unit has a problem with toner supply or sensor calibration.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Check if the toner supply pipe is blocked. If it is closed, open it. 4) Install the waste toner container. Close the front cover. 5) Turn the machine off then on. 6) If the problem persists, remove and reinstall the magenta developer unit. 7) If the problem persists, replace the magenta developer unit.

Error code:	C8-3410
Display:	Magenta developer unit is not installed. Install it
Description:	The magenta developer unit is not installed.
Remedy:	1) Open the front cover. 2) Check if all developer unit is installed. Remove and re-install the developer unit.

Error code:	C8-4110, C8-4125
Display:	Prepare new cyan developer unit Replace with new cyan developer unit. Call for service
Description:	The life of the cyan developer unit expires soon or has expired.
Remedy:	1) If its life is at the end, turn the machine off and replace the developer unit with new one.

Error code:	C8-4210, C8-4310, C8-4313
Display:	Cyan Developer Failure: #C8-4210. Turn off then on Cyan Developer Failure: #C8-4310. Install cyan developer unit again Cyan Developer Failure: #C8-4313. Turn off then on. Please call for service if the problem persists
Description:	Cyan Developer Failure: #C8-4210. Turn off then on Cyan Developer Failure: #C8-4310. Install cyan developer unit again Cyan Developer Failure: #C8-4313. Turn off then on. Please call for service if the problem persists
Causes:	The cyan developer unit has a problem with toner supply or sensor calibration.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Check if the toner supply pipe is blocked. If it is closed, open it. 4) Install the waste toner container. Close the front cover. 5) Turn the machine off then on. 6) If the problem persists, remove and reinstall the cyan developer unit. 7) If the problem persists, replace the cyan developer unit.

Error code:	C8-4410
Display:	Cyan developer unit is not installed. Install it
Description:	The cyan developer unit is not installed.
Remedy:	1) Open the front cover. 2) Check if all developer unit is installed. Remove and re-install the developer unit.

Error code:	C8-5110, C8-5125
Display:	Prepare new black developer unit Replace with new black developer unit. Call for service
Description:	The life of the black developer unit expires soon or has expired.
Remedy:	1) If its life is at the end, turn the machine off and replace the developer unit with new one.

Error code:	C8-5210, C8-5310, C8-5313
Display:	Black Developer Failure: #C8-5210. Turn off then on Black Developer Failure: #C8-5310. Install black developer unit again Black Developer Failure: #C8-5313. Turn off then on. Please call for service if the problem persists
Description:	Black Developer Failure: #C8-5210. Turn off then on Black Developer Failure: #C8-5310. Install black developer unit again Black Developer Failure: #C8-5313. Turn off then on. Please call for service if the problem persists
Causes:	The black developer unit has a problem with toner supply or sensor calibration.
Remedy:	1) Open the front cover. 2) Remove the waste toner container. 3) Check if the toner supply pipe is blocked. If it is closed, open it. 4) Install the waste toner container. Close the front cover. 5) Turn the machine off then on. 6) If the problem persists, remove and reinstall the black developer unit. 7) If the problem persists, replace the black developer unit.

Error code:	C8-5410
Display:	Black developer unit is not installed. Install it
Description:	The black developer unit is not installed.
Remedy:	1) Open the front cover. 2) Check if all developer unit is installed. Remove and re-install the developer unit.

Error code:	C9-1112, C9-1122, C9-1132, C9-1142
Display:	Replace with new Tray1 pickup roller. Replace with new Tray2 pickup roller. Replace with new Tray3 pickup roller. Replace with new Tray4 pickup roller.
Description:	The life of the pick up/reverse/forward roller for tray1,2,3,4 has expired.
Remedy:	1) Open the side cover. 2) Remove the cassette while pushing the both sides linkers. 3) Lift small tap, remove the pick up / reverse/ forward roller. 4) Enter SVC mode. To enter SVC mode, press 1,2,3 number keys simultaneously. When the password dialog box appears, enter “1934” and press the “OK” button. 5) Select “Roller” (INFORMATION > Supply Status > Field Replacement Unit > Roller) 6) Select “P/up roller Kit-tray1-4”. The “RESET” button will be activated. Click “RESET” to clear the corresponding pick up roller. 7) Exit SVC mode by pushing the home button.

Error code:	C9-1162
Display:	Replace with new MP pickup roller
Description:	Replace new MP Pickup roller
Causes:	The MP pick up roller is at the end of its life.
Remedy:	1) Turn the machine off. 2) Replace the MP pick up roller.

Error code:	C9-2110, C9-2120
Display:	Replace with new Transfer roller.
Description:	Replace with new Transfer roller.
Causes:	The life of the second transfer roller(T2) expires soon or has expired.
Remedy:	1) Open the side cover. 2) Replace the second transfer roller(JC95-01942A) with a new one. 3) Close the side cover. 4) Enter SVC mode. • To enter the service mode, tap "Service Mode" App. When the password dialog box appears, enter “1934” and press the “OK” button. 5) Select “TRANSFER” (INFORMATION > Supply Status > Field Replacement Unit > TRANSFER) 6) Select “T2 Roller”. The “RESET” button will be activated. Click “RESET” to clear the T2 Roller count. 7) Exit the SVC mode by pushing the home button.

Error code:	C9-2220
Display:	TR Failure: #C9-2220. Install transfer roller again.
Description:	TR Failure: #C9-2220. Install transfer roller again
Causes:	The life of the second transfer roller(T2) is not installed.
Remedy:	1) Open the side cover. 2) Remove and reinstall the second transfer roller. 3) Close the side cover. 4) If the problem persists, replace the HVPS board(JC44–00212A).

Error code:	H1-1211
Display:	Paper jam in Tray 2.
Description:	Paper jam has occurred around the pick up roller of the tray2.
Remedy:	1) Remove the tray2. Remove the jammed paper. And install the tray2. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers(JC93-00616A). 5) Check the lifting sensor and lifting motor operations. • When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor(0604-001415) • If the lifting motor does not operate normally, replace the DRIVE-LIFT TCF(JC93-00722A).

Error code:	H1-1213
Display:	Paper jam in Tray 2.
Description:	Paper is not reached to the feed sensor after pick-up.
Remedy:	1) Remove the tray2. Remove the jammed paper. And install the tray. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers(JC93-00616A). 5) Check the feed sensor operations. If the feed sensor is defective, replace it(0604-001381).

Error code:	H1-1217, H1-1218
Display:	Paper jam in Tray 2.
Description:	Paper jam has occurred in tray2. Paper is not reached to the feed sensor after pick-up from tray2.
Remedy:	• H1-1217 : Paper is not reached to the feed sensor after pick-up from tray2. • H1-1218 : Paper is not passed the feed sensor within specified time. 1) Remove the tray2. Remove the jammed paper. And install the tray. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers(JC93-00616A). 5) Check the feed sensor and feed motor operations. • When the paper or something puts on feed sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor(0604-001381) • If the feed motor does not operate normally, replace the DRIVE-PH TCF(JC93-00720A).

Error code:	H1-1230, H1-1236, H1-1237
Display:	Input System Failure: #H1-1230. Check Tray 2 connection. Tray Failure: #H1-1236. Check Tray connection Tray Failure: #H1-1237. Check Tray connection
Description:	The communication error between the optional tray and the main machine has occurred.
Remedy:	1) Check if the TCF unit connector is connected to the machine correctly. Reconnect it. 2) Check if the TCF connector on main board is connected correctly.

Error code:	H1-1253
Display:	Input System Failure #H1-1253 : Pull Tray 2 out and insert it.
Description:	The paper is not fed from tray2.
Causes:	The paper is not fed from tray2.
Remedy:	1) Check if the Gear-Idle Lift is broken. 2) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 3) If the connection is OK, replace the cassette detection sensor(JC34-00001A). 4) Check if the Lift-Motor connector is connected properly. 5) If the problem persists, replace the Lift-Motor(JC81-08705A).

Error code:	H1-1311
Display:	Paper jam in Tray 3.
Description:	Paper jam has occurred around the pick up roller of the tray3.
Remedy:	1) Remove the tray3. Remove the jammed paper. And install the tray3. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers(JC93-00616A). 5) Check the lifting sensor and lifting motor operations. • When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor(0604-001415) • If the lifting motor does not operate normally, replace the DRIVE-LIFT TCF(JC93-00722A).

Error code:	H1-1317, H1-1318
Display:	Paper jam in Tray 3.
Description:	Paper jam in Tray 3.
Causes:	Paper jam has occurred in tray3. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.)
Remedy:	1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray3. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray3. 3) If this jam error occurs frequently, check the rollers below. a) Remove the tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit1. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit1. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit1. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit1(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A).

Error code:	H1-1353
Display:	Input System Failure #H1-1353 : Pull Tray 3 out and insert it.
Description:	Input System Failure #H1-1353 : Pull Tray 3 out and insert it.
Causes:	The paper is not fed from tray3.
Remedy:	1) Remove and insert tray3 correctly. 2) Turn the machine off then on. 3) If the problem persists, turn the machine off. 4) Remove the Bracket Rear Cover after removing 5 screws. 5) Check if the connection between the DCF pick up drive and DCF board is correct. 6) If the connection is OK, replace the pick up drive unit(JC93-00442A). 7) If the problem persists, check the following. a) Remove the DCF pick up unit1. b) Check if the photo sensor in the DCF pick up unit1 is contaminated, clean it. c) If the photo sensor(0604-001393) is defective, replace it.

Error code:	H1-1411
Display:	Paper jam in Tray 4.
Description:	Paper jam has occurred around the pick up roller of the tray4.
Remedy:	1) Remove the tray4. Remove the jammed paper. And install the tray4. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray4. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers(JC93-00616A). 5) Check the lifting sensor and lifting motor operations. • When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor(0604-001415) • If the lifting motor does not operate normally, replace the DRIVE-LIFT TCF(JC93-00722A).

Error code:	H1-1417, H1-1418
Display:	Paper jam in Tray 4.
Description:	Paper jam in Tray 4.
Causes:	Paper jam has occurred in tray4. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.)
Remedy:	1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray4. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray4. 3) If this jam error occurs frequently, check the rollers below. a) Remove tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit2. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit2. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit2. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit2(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A).

Error code:	H1-1453
Display:	Input System Failure #H1-1453 : Pull Tray 4 out and insert it.
Description:	Input System Failure #H1-1453 : Pull Tray 4 out and insert it.
Causes:	The paper is not fed from tray4.
Remedy:	1) Remove and insert tray4 correctly. 2) Turn the machine off then on. 3) If the problem persists, turn the machine off. 4) Remove the Bracket Rear Cover after removing 5 screws. 5) Check if the connection between the DCF pick up drive and DCF board is correct. 6) If the connection is OK, replace the pick up drive unit(JC93-00442A). 7) If the problem persists, check the following. a) Remove the DCF pick up unit2. b) Check if the photo sensor in the DCF pick up unit2 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it.

Error code:	H2-5001, H2-5002, H2-5096
Display:	Finisher Failure #. Turn off then on, after checking finisher
Description:	Finisher Failure #H2-5001. Turn off then on, after checking finisher Finisher Failure #H2-5002. Turn off then on, after checking finisher Finisher Failure #H2-5096. Turn off then on, after checking finisher
Causes:	Main Paddle operation is abnormal. (Paddle home failure / Paddle move failure)
Remedy:	1) Is the Main Paddle overruns during the operation? a) Check if the Paddle home sensor actuator(SJ10 3302) is abnormality. b) Check if the connector(SJ10 8310) of Paddle home sensor (S4) is disconnected. c) Check if the connector(SJ10 8310) J8 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (JR10 8310), replace as is necessary. e) Replace the finisher Paddle home sensor(S4). f) Replace the Finisher main board(JC81–07242A). 2) Is the Paddle Motor (M3) working? a) Check if the connector(JR10 8320) of Paddle motor(M3) is disconnected. b) Check if the connector(JR10 8320) J5 on the finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Paddle motor(M3). e) Replace the Finisher main board(JC81–07242A). 3) Check if the gears(SJ10 3308) of Paddle motor(M3) are assembled correctly. 4) Check if the tooth of gears(SJ10 3308) are broken. If it is defective, replace the broken gears(SJ10 3308). 5) Check if the Paper Path Diverter gears(cam) (JR10 3302) are assembled correctly or operated well. 6) Check if the gears(cam) (JR10 3302) are broken. If it is defective, replace the broken gears(cam). 7) Replace the Paddle Unit(JR10 3130).

Error code:	H2-5003, H2-5004, H2-5097
Display:	Finisher Failure #. Turn off then on, after checking finisher
Description:	Finisher Failure #H2-5003. Turn off then on, after checking finisher Finisher Failure #H2-5004. Turn off then on, after checking finisher Finisher Failure #H2-5097. Turn off then on, after checking finisher
Causes:	Front Jogger operation is abnormal.
Remedy:	1) Is the Front Jogger Home sensor (S6) working? a) Check if the Front Jogger home sensor actuator(SJ10 3318) is abnormality. b) Check if the connector(SJ10 8310) of Front Jogger home sensor(S6) is disconnected. c) Check if the connector(SJ10 8310) J8 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (JR10 8310), replace as is necessary. e) Replace the Front Jogger home sensor(S6). f) Replace the Finisher main board(JC81–07242A). 2) Is the Front Jogger motor (M5) working? a) Check if the connector (SJ10 8310)of Front Jogger motor(M5) is disconnected. b) Check if the connector (SJ10 8310) J6 on the finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8310), replace as is necessary. d) Replace the Front Jogger motor(M5). e) Replace the Finisher main board(JC81–07242A). 3) Is there any belt(gear) jumping noise? a) Check if the Front Jogger driving belt(JC81-03509A) is assembled correctly. b) Check if the Front Jogger driving belt(JC81-03509A) is broken. Replace the belt if it does. c) Check if the Front Jogger motor bracket(SJ10 3206) is fasten on tamper base(JR10 3304) by screw. d) Check if the tooth of gear(SJ10 3308) is broken. Replace the gear if it does. e) Check if the Front Jogger shaft(JR10 3304) became pollution. Remove if it does. 4) Replace the Front Jogger Unit(JC81-03511C).

Error code:	H2-5005, H2-5006, H2-5098
Display:	Finisher Failure #. Turn off then on, after checking finisher
Description:	Finisher Failure #H2-5005. Turn off then on, after checking finisher Finisher Failure #H2-5006. Turn off then on, after checking finisher Finisher Failure #H2-5098. Turn off then on, after checking finisher
Causes:	Rear Jogger operation is abnormal.
Remedy:	1) Is the Rear Jogger Home sensor (S5) working? a) Check if the Rear Jogger home sensor actuator(SJ10 3318) is abnormality. b) Check if the connector(JR10 8320) of Rear Jogger home sensor(S5) is disconnected. c) Check if the connector(JR10 8320) J7 on the finisher main board(JC81–07242A) is disconnected. d) Check discontinuity and damage of the harness(JR10 8320), replace it if required. e) Replace the Rear Jogger home sensor(S5). f) Replace the Finisher main board(JC81–07242A). 2) Is the Rear Jogger motor (M4) working? a) Check if the connector(JR10 8320) of Rear Jogger motor is disconnected. b) Check if the connector(JR10 8320) J5 on the finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Rear Jogger motor(M4). e) Replace the Finisher main board(JC81–07242A). 3) Is there any belt(gear) jumping noise? a) Check if the Rear Jogger driving belt(JC81-03509A) is assembled correctly. b) Check if the Rear Jogger driving belt(JC81-03509A) is broken. Replace the belt if it does. c) Check if the Rear Jogger motor bracket(SJ10 3206) is fasten on tamper base(JR10 3306) by screw. d) Check if any of the teeth on gear (SJ10 3308) are broken. Replace the gear if necessary. e) Check if the Front Jogger shaft (JR10 3304) is contaminated. Clean as is necessary. 4) Replace the Rear Jogger Unit(JC81-03507C).

Error code:	H2-5007, H2-5008, H2-5099
Display:	Finisher Failure #. Turn off then on, after checking finisher
Description:	Finisher Failure #H2-5007. Turn off then on, after checking finisher Finisher Failure #H2-5008. Turn off then on, after checking finisher Finisher Failure #H2-5099. Turn off then on, after checking finisher
Causes:	Extension Tray operation is abnormal.
Remedy:	1) Is the Extension Tray Home sensor (S9) working? a) Check if the Extension Tray home sensor actuator(JC81-03483B) is abnormality. b) Check if the connector(SJ10 8380) of Extension Tray home sensor(S9) is disconnected. c) Check if the connector(SJ10 8310) J8 on the finisher main board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace it if required. e) Replace the Extension Tray home sensor(S9). f) Replace the Finisher main board(JC81–07242A). 2) Is the Extension Tray motor (M6) working? a) Check if the connector (SJ10 8310) of Extension Tray motor is disconnected. b) Check if the connector(SJ10 8310) J6 on the finisher main board(JC81–07242A) is disconnected. c) Check continuity and if the harness is damaged, replace it if required. d) Replace the Extension Tray motor(M6). e) Replace the Finisher main board(JC81–07242A). 3) Check if the gears(SJ10 5342) are assembled correctly. 4) Check if the tooth of gears(SJ10 5342) are broken. Replace the broken gears. 5) Check if the Extension Tray Home sensor bracket(SJ10 5120) is deformed.(make a right angle) Replace the bracket. 6) Replace the Extension Tray Unit(SJ10 5000).

Error code:	H2-5009, H2-5010
Display:	Finisher Failure #. Turn off then on, after checking finisher
Description:	Finisher Failure #H2-5009. Turn off then on, after checking finisher Finisher Failure #H2-5010. Turn off then on, after checking finisher
Causes:	Ejector operation is abnormal.
Remedy:	1) Is the ejector home sensor (S8) working? a) Check if the Ejector home sensor actuator(SJ10 2382) is abnormal. b) Check if the connector(SJ10 8360) of ejector home sensor is disconnected. c) Check if the connector(JR10 8320) J7 on the finisher main board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace it if required. e) Replace the ejector home sensor(S8). f) Replace the Finisher main board(JC81–07242A). 2) Is the ejector moves very fast? a) Check if the Ejector Encoder sensor actuator (SJ10 4362) is abnormal. b) Check if the connector(SJ10 8310) of ejector encoder sensor(S17) is disconnected. c) Check if the connector(SJ10 8310) J13 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (SJ10-8310), replace as is necessary. e) Replace the ejector encoder sensor(S17). f) Replace the Finisher main board(JC81–07242A). 3) Is the ejector motor (M7) working? a) Check if the connector(SJ10 8310) of ejector motor(SJ10 4143) is disconnected. b) Check if the connector(SJ10 8310) J6 on the finisher main board(JC81–07242A) is disconnected. c) Check continuity and if the harness is damaged, replace it if required. d) Replace the ejector motor(M7). e) Replace the Finisher main board(JC81–07242A). 4) Can you hear the sound that the ejector driving belt is jumping during operation? a) Check if the ejector motor bracket(SJ10 4204) assembly is fasten on compiler bottom frame by screw. 5) Check if the tooth of gears(SJ10 4304) are broken. Replace the broken gears. 6) Replace the ejector unit(JC81-03773C).

Error code:	H2-5011, H2-5100
Display:	Finisher Failure #. Turn off then on, after checking finisher
Description:	Finisher Failure #H2-5011. Turn off then on, after checking finisher Finisher Failure #H2-5100. Turn off then on, after checking finisher
Causes:	Ejector operation is abnormal.
Remedy:	1) Is the ejector home sensor (S8) working? a) Check if the Ejector home sensor actuator(SJ10 2382) is abnormal. b) Check if the connector(SJ10 8360) of ejector home sensor is disconnected. c) Check if the connector(JR10 8320) J7 on the finisher main board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace it if required. e) Replace the ejector home sensor(S8). f) Replace the Finisher main board(JC81–07242A). 2) Is the ejector moves very fast? a) Check if the Ejector Encoder sensor actuator (SJ10 4362) is abnormal. b) Check if the connector(SJ10 8310) of ejector encoder sensor(S17) is disconnected. c) Check if the connector(SJ10 8310) J13 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (SJ10-8310), replace as is necessary. e) Replace the ejector encoder sensor(S17). f) Replace the Finisher main board(JC81–07242A). 3) Is the ejector motor (M7) working? a) Check if the connector(SJ10 8310) of ejector motor(SJ10 4143) is disconnected. b) Check if the connector(SJ10 8310) J6 on the finisher main board(JC81–07242A) is disconnected. c) Check continuity and if the harness is damaged, replace it if required. d) Replace the ejector motor(M7). e) Replace the Finisher main board(JC81–07242A). 4) Can you hear the sound that the ejector driving belt is jumping during operation? a) Check if the ejector motor bracket(SJ10 4204) assembly is fasten on compiler bottom frame by screw. 5) Check if the tooth of gears(SJ10 4304) are broken. Replace the broken gears. 6) Replace the ejector unit(JC81-03773C).

Error code:	H2-5012, H2-5013, H2-5101
Display:	Finisher Failure #. Turn off then on, after checking finisher
Description:	Finisher Failure #H2-5012. Turn off then on, after checking finisher Finisher Failure #H2-5013. Turn off then on, after checking finisher Finisher Failure #H2-5101. Turn off then on, after checking finisher
Causes:	Stapler head clinching motor is not working properly.
Remedy:	1) Is the Head of Stapler(JC81-03475B) opened? a) Replace stapler cartridge(JC81-03481A). b) Check if the connectors(SJ10 8310) of stapler head are disconnected. c) Check if the connector(SJ10 8310) P7 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (SJ10-8310), replace as is necessary. e) Replace the stapler unit(SJ10 3140). f) Replace the Finisher main board(JC81–07242A). 2) Replace the stapler unit(SJ10 3140).

Error code:	H2-5014, H2-5015, H2-5102
Display:	Finisher Failure #. Turn off then on, after checking finisher
Description:	Finisher Failure #H2-5014. Turn off then on, after checking finisher Finisher Failure #H2-5015. Turn off then on, after checking finisher Finisher Failure #H2-5102. Turn off then on, after checking finisher
Causes:	Stacker operation is abnormal.
Remedy:	1) Are the Stacker Upper Limit(Top) Sensors (S10) working? a) Check if the sensor actuator(SJ10 6332A) is abnormality. b) Check if the connector(SJ10 8370) of the sensors are disconnected. c) Check if the connector(SJ10 8310) J8 on the finisher main board(JC81–07242A) is disconnected. d) Check discontinuity and damage of the harness(SJ10 8310, SJ10 8370), replace it if required. e) Replace the stacker upper limit sensors(S10). f) Replace the Finisher main board(JC81–07242A). 2) Is the Stacker Full Sensor (S16) working? a) Check if the sensor actuator(JR10 6210) is abnormality. b) Check if the connector(JR10 8320) of stacker full sensor is disconnected. c) Check if the connector(JR10 8320) J18 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (SJ10 8320), replace as is necessary. e) Replace the stacker encoder sensor(S16). f) Replace the Finisher main board(JC81–07242A). 3) Is the stacker Lower Limit Switch (SW2) working? a) Check if the sensor actuator(JR10 6310) is abnormality. b) Check if the connector(JR10 8360) of stacker Lower switch is disconnected. c) Check if the connector(JR10 8360) J14 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (JR10 8360), replace as is necessary. e) Replace the stacker bottom limit sensor(SW2). f) Replace the Finisher main board(JC81–07242A). 4) Is the stacker motor (M8) working? a) Check if the connector(JR10 8360) of stacker motor is disconnected. b) Check if the connector(JR10 8360) J14 on the finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8360), replace as is necessary. d) Replace the stacker motor(M8). e) Replace the Finisher main board(JC81–07242A). 5) Replace the stacker motor gear box(SJ10 6110).

Error code:	H2-5032
Display:	Paper jam in front of finisher: #H2-5032
Description:	Paper jam in front of finisher: #H2-5032
Causes:	Sheet not leaving finisher paper path section.
Remedy:	Check if there is any paper on the finisher, the IOT paper path. Remove it if there is. If the error still occurs, check the followings. 1) Check if the Finisher of the interface cable(JC81-03470A) should be connected with the IOT. a) Power of the IOT Off. b) IOT and Finisher of the interface cable(JC81-03470A) is connected. c) Power of the IOT On. 2) Is the LEDs of the Main Control Board (JC81–07242A) working? <Open the Bottom cover (SJ10 6160) of Finisher > a) The Finisher Guides (JC63-03941A, JC81-07249B) need to be placed in the UP Position, so the Front Door can be closed properly. b) Red, yellow color LED is ON, and Green LED flickers c) Replace the Finisher main control board(JC81–07242A). 3) Is the Finisher Entrance Sensor(S2) working? a) Check if the Entrance sensor actuator(SJ10 2384) is abnormality. b) Check if the connector (SJ10 8350)of Finisher entrance sensor(S2) is disconnected. c) Check if the connector(JR10 8320) J7 on the Finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (SJ10 8350, SJ10 8320), as is necessary. e) Replace the Finisher input sensor(S2). f) Replace the Finisher main control board(JC81–07242A). 4) Is the Feed Entrance Motor (M1) working? a) Check if the connector(JR10 8320) of the Feed entrance motor is disconnected. b) Check if the connector(JR10 8320) J5 on the Finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Feed entrance motor(M1). e) Replace the Finisher main control board(JC81–07242A). 5) Check if there is any object on finisher paper path. Remove it if there is.

Error code:	H2-5033, H2-5035, H2-5036
Display:	Paper jam inside of finisher: #
Description:	Paper jam inside of finisher: #H2-5033 Paper jam inside of finisher: #H2-5035 Paper jam inside of finisher: #H2-5036
Causes:	Sheet jam on finisher paper path section
Remedy:	Check if there is any paper on the finisher, the IOT paper path. Remove it if there is. If the error still occurs, check the followings. 1) Is the Finisher Entrance Sensor(S2) working? a) Check if the Entrance sensor actuator(SJ10 2384) is abnormality. b) Check if the connector(SJ10 8350) of Finisher entrance sensor(S2) is disconnected. c) Check if the connector(JR10 8320) J7 on the Finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (JR10 8320, SJ10 8350), replace as is necessary. e) Replace the Finisher entrance sensor(S2). f) Replace the Finisher main control board(JC81–07242A). 2) Is the Feed Entrance Motor (M1) working? a) Check if the connector(JR10 8320) of the Feed entrance motor is disconnected. b) Check if the connector(JR10 8320) J5 on the Finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Feed entrance motor(M1). e) Replace the Finisher main control board(JC81–07242A). 3) Is the Finisher Exit Sensor (S3,S11) working? a) Check if the Exit sensor actuator (SJ10 2384) is abnormality. b) Check if the connector(SJ10 8340) of the Finisher Exit sensor(S3) is disconnected. c) Check if the connector(JR10 8320) J7 on the Finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (JR10 8320, SJ10 8340), replace as is necessary. e) Replace the Finisher exit sensor(S3,S11). f) Replace the Finisher main control board(JC81–07242A). 4) Is the Feed Exit Motor(M2) working? a) Check if the connector(JR10 8320) of the Feed exit motor is disconnected. b) Check if the connector J5 on the finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Feed exit motor(M2). e) Replace the Finisher main control board(JC81–07242A). 5) Check if there is any object on finisher paper path. Remove it if there is.

Error code:	H2-5034, H2-5037
Display:	Finisher Failure #H2-5003. Turn off then on, after checking finisher
Description:	Finisher Failure #H2-5003. Turn off then on, after checking finisher
Causes:	Sheet jam on finisher exit section
Remedy:	Check if there is any paper on the finisher, the IOT paper path. Remove it if there is. If the error still occurs, check the followings. 1) Is the Finisher Exit Sensor(S3, S11) working? a) Check if the Exit sensor actuator (SJ10 2384)is abnormality. b) Check if the connector(SJ10 8340) of the Finisher Exit sensor(S3) is disconnected. c) Check if the connector(JR10 8320) J7 on the Finisher main board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged , replace as is necessary. e) Replace the Finisher exit sensor(S3,S11). f) Replace the Finisher main control board(JC81–07242A). 2) Is the Feed Exit Motor(M2) working? a) Check if the connector(JR10 8320) of the Feed exit motor is disconnected. b) Check if the connector J5 on the finisher main board(JC81 07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Feed exit motor(M2). e) Replace the Finisher main control board(JC81 07242A). 3) Check if there is any object on finisher paper path. Remove it if there is.

Error code:	H2-5048
Display:	Finisher door is open. Close it
Description:	Finisher door is open. Close it
Causes:	Finisher Door is Opened. Power(24V) supply is cut off, and then stop the operation of Finisher.
Remedy:	Check if the all door of finisher closed. If the error still occurs, check the followings. 1) Is the all Doors of Finisher closed? a) Close the doors(JC63-03941A) opened. 2) Is the Front Door (JC63-03941A) Switch (SW1) working? a) Check if the Switch(SW1) and the Actuator(JC63-03941A) is abnormality. b) Check if the connector(JR10 8360) of Switch is disconnected. c) Check if the connector(JR10 8360) J2 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace the Door switch(SW1). f) Replace the Finisher main control board(JC81–07242A).

Error code:	H2-506x, H2-507x, H2-5A50
Display:	Finisher Failure #H2-506x. Turn off then on, after checking finisher Finisher Failure #H2-507x. Turn off then on, after checking finisher Finisher Failure #H2-5A50. Check finisher
Description:	Finisher Failure #H2-506x. Turn off then on, after checking finisher Finisher Failure #H2-507x. Turn off then on, after checking finisher Finisher Failure #H2-5A50. Check finisher
Causes:	Communication error between the IOT and the Finisher.
Remedy:	If the error still occurs, check the followings. 1) Check if the Finisher of the interface cable(JC81-03470A) should be connected with the IOT. a) Power Switch of the IOT Off. b) IOT and Finisher of the interface cable(JC81-03470A) is connected. c) Power Switch of the IOT On. 2) Is the LEDs of the Main Control Board (JC81–07242A) working? < Open the Bottom cover(SJ10 6160) of Finisher > a) The Finisher of the Doors(JC63-03941A, JC81-07249B) should remain closed to all. b) Red, yellow color LED is ON, and Green LED flickers. c) Replace the Finisher main control board(JC81–07242A). 3) Check the Interface Cable(JC81-03470A) of Main Control Board(JC81–07242A). a) Check if the connector(JC81–07242A) J1,J3 on the main control board (JC81–07242A) is disconnected. b) Check continuity and if the harness is damaged(JC81-03470A), replace as is necessary. c) Replace the Finisher main control board(JC81–07242A). 4) Replace the Finisher main control board(JC81–07242A).

Error code:	H2-5A21
Display:	Finisher Top door is open. Close it
Description:	Finisher Top door is open. Close it
Causes:	Finisher Top Door is Opened.
Remedy:	Check if the all door of finisher closed. If the error still occurs, check the followings. 1) Are all Paper Guides in there up position; and is the Front Door of Finisher closed? a) Close the Top Door(JC81-07249B) opened. 2) Is the Top Door Sensor (S16) working? a) Check if the top door sensor actuator(JC81-07249B) is abnormality. b) Check if the connector(JR10 8330) of sensor is disconnected. c) Check if the connector(JR10 8330) J1,J2 on the main control board (JC81–07242A)is disconnected. d) Check continuity and if the harness is damaged , replace as is necessary. e) Replace the Finisher top Door sensor(S16). f) Replace the Finisher main control board(JC81–07242A). 3) Replace the Finisher main control board(JC81–07242A).

Error code:	H2-5A31, H2-5A32
Display:	The paper in finisher stacker is nearly full. Remove printed paper The paper in finisher stacker is full. Remove printed paper The paper in finisher bin2 is nearly full. Remove printed paper The paper in finisher bin2 is nearly full. Remove printed paper
Description:	The paper in finisher stacker is nearly full. Remove printed paper The paper in finisher stacker is full. Remove printed paper
Causes:	Finisher stacker tray made full, or Stacker operation is abnormal.
Remedy:	Check if there is any paper on the Finisher Stacker Tray. Remove it if there is. If the error still occurs, check the followings. 1) Is the Finisher Stack Height Sensor (S10) working? a) Check if the Stack height sensor actuator(SJ10 6332A) is abnormality. b) Check if the connector (SJ10 8370)of Stack height sensor(S10) is disconnected. c) Check if the connector(SJ10 8310) J8 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace the finisher Stack height sensor(S10). f) Replace the Finisher main control board(JC81–07242A). 2) Is the Finisher Stack Full Sensor (S17) working? a) Check if the Stack full sensor actuator(SJ10 6332A) is abnormality. b) Check if the connector of Stack full sensor is disconnected. c) Check if the connector(JR10 8320) J18 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace the finisher stack full sensor(S10). f) Replace the Finisher main control board(JC81–07242A). 3) Is the Stacker Motor (M8) working? a) Check if the connector(SJ10 8360) of stacker motor is disconnected. b) Check if the connector(SJ10 8360) J14 on the finisher main board(JC81–07242A) is disconnected. c) Check continuity and if the harness is damaged, replace as is necessary. d) Replace the stack motor(M8). 4) Replace the Finisher main control board(JC81–07242A).

Error code:	H2-5A34, H2-5A35
Display:	The paper in finisher stacker is nearly full. Remove printed paper The paper in finisher stacker is full. Remove printed paper The paper in finisher bin2 is nearly full. Remove printed paper The paper in finisher bin2 is nearly full. Remove printed paper
Description:	The paper in finisher bin2 is nearly full. Remove printed paper The paper in finisher bin2 is nearly full. Remove printed paper
Causes:	Finisher stacker tray made full, or Stacker operation is abnormal.
Remedy:	Check if there is any paper on the Finisher Stacker Tray. Remove it if there is. If the error still occurs, check the followings. 1) Is the Finisher Stack Height Sensor (S10) working? a) Check if the Stack height sensor actuator(SJ10 6332A) is abnormality. b) Check if the connector (SJ10 8370)of Stack height sensor(S10) is disconnected. c) Check if the connector(SJ10 8310) J8 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace the finisher Stack height sensor(S10). f) Replace the Finisher main control board(JC81–07242A). 2) Is the Finisher Stack Full Sensor (S17) working? a) Check if the Stack full sensor actuator(SJ10 6332A) is abnormality. b) Check if the connector of Stack full sensor is disconnected. c) Check if the connector(JR10 8320) J18 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace the finisher stack full sensor(S10). f) Replace the Finisher main control board(JC81–07242A). 3) Is the Stacker Motor (M8) working? a) Check if the connector(SJ10 8360) of stacker motor is disconnected. b) Check if the connector(SJ10 8360) J14 on the finisher main board(JC81–07242A) is disconnected. c) Check continuity and if the harness is damaged, replace as is necessary. d) Replace the stack motor(M8). 4) Replace the Finisher main control board(JC81–07242A).

Error code:	H2-5A62, H2-5A63
Display:	Staple cartridge is low. Replace it Staple cartridge is empty or not installed. Replace it
Description:	Staple cartridge is low. Replace it Staple cartridge is empty or not installed. Replace it
Causes:	Can not detected Staple cartridge .
Remedy:	Check if there is Staple Cartridge. If the error still occurs, check the followings 1) Is the Staple Cartridge mounted? a) Replace stapler cartridge(JC81-03481A). b) Check if the connector (SJ10 8310)of Staple is disconnected. c) Check if the connector(SJ10 8310) J9,J10 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace staple unit(SJ10 3140). f) Replace the Finisher main control board(JC81–07242A). 2) Mount the stapler cartridge(JC81-03481A). 3) Replace the stapler Unit(SJ10 3140)

Error code:	H2-5A90
Display:	Paper jam at the top of finisher: #H2-5A90
Description:	Paper jam at the top of finisher: #H2-5A90
Causes:	Sheet jam on finisher top exit section
Remedy:	Check if there is any paper on the finisher, the IOT paper path. Remove it if there is. If the error still occurs, check the followings. 1) Is the Top Exit/Top Empty Sensor(S13, S11) working? a) Check if the Sensor actuator (SJMB2312, SJMB2310) abnormality. b) Check if the connector(JR10 8340) of the Top exit/Top empty sensor(S13, S12) is disconnected. c) Check if the connector(JR10 8330J7 on the Finisher main board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged , replace as is necessary. e) Replace the Top exit/Top Empty sensor(S13,S12). f) Replace the Finisher main control board(JC81–07242A). 2) Is the Paddle Unit(Paper path diverter) working? a) Refer to the troubleshooting for “H2–5001” error. 3) Check if there is any object on finisher paper path. Remove it if there is.

Error code:	M1-1113, M1-1114
Display:	Paper jam in Tray 1.
Description:	Paper jam has occurred in tray1.
Remedy:	1) Remove the tray1. Remove the jammed paper. And install the tray. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers(JC93-00616A). 5) Check the lifting sensor and lifting motor operations. • When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor(0604-001415) • If the lifting motor does not operate normally, replace it(JC93-00567A). 6) If the problem persists, replace the PICKUP CLUTCH(JC47-00039A). 7) If the problem persists, replace the Regi Sensor(0604-001381).

Error code:	M1-1610
Display:	Paper jam in MP Tray.
Description:	Paper Jamin MP tray
Causes:	The jammed paper has occurred in the MP tray.
Remedy:	1) Remove the jammed paper. 2) If the jammed paper occurs continually, check the followings. a) Check if the pick up/forward/reverse roller are worn out or contaminated. Clean the contaminated part or replace it. b) Check if the actuator is assembled correctly. 3) If the pick up clutch is defective, replace it. 4) If the problem persists, replace the MP unit.

Error code:	M2-2113
Display:	Paper jam at the top of duplex path
Description:	Paper is not reached at the duplex jam sensor and jam has occurred.
Remedy:	• Jam Occurrence Location 1) Check if there is any substance on duplex path. Remove it. 2) Clean the surface of the duplex roller-1. If it is broken or deformed, replace it(JC66-03510A). 3) Enter SVC mode. Execute duplex motor1 test. (Diagnostics > Engine Diagnostics > Engine Test Routines > Duplex Motor Forward) • If the motor operation is abnormal, check the motor connection. If the connection is OK, replace the motor(JC93-00569A) from the exit unit. 4) Check if the exit sensor actuator operates normally. If actuator or spring is defective, replace it. 5) Check if the duplex jam sensor actuator is assembled correctly. If the photo interruptor is defective, replace it(0604-001415).

Error code:	M2-2114
Display:	Paper jam at the top of duplex path
Description:	Paper is not passed the duplex jam sensor and jam has occurred.
Remedy:	• Jam Occurrence Location 1) Check if there is any substance on duplex path. Remove it. 2) Clean the surface of the duplex roller-2. If it is broken or deformed, replace it(JC66-03494A). 3) Enter SVC mode. Execute duplex motor2 test. (Diagnostics > Engine Diagnostics > Engine Test Routines > Duplex2 Motor Forward) • If the motor operation is abnormal, check the motor connection. If the connection is OK, replace the motor(JC93-00301A) from the duplex unit. 4) Check if the duplex jam sensor actuator is assembled correctly. If the photo interruptor is defective, replace it(0604-001415).

Error code:	M2-2215
Display:	Paper jam at the inside of duplex path
Description:	Paper is not reached the duplex ready sensor and jam has occurred.
Remedy:	• Jam Occurrence Location 1) Check if there is any substance on duplex path. Remove it. 2) Clean the surface of the duplex roller-2. If it is broken or deformed, replace it(JC66-03494A). 3) Enter SVC mode. Execute duplex motor2 test. (Diagnostics > Engine Diagnostics > Engine Test Routines > Duplex2 Motor Forward) • If the motor operation is abnormal, check the motor connection. If the connection is OK, replace the motor(JC93-00301A) from the duplex unit. 4) Check if the duplex ready sensor actuator is assembled correctly. If the spring is defective, replace it(6107-003137).

Error code:	M2-2216
Display:	Paper jam at the inside of duplex path
Description:	Paper is not passed the duplex ready sensor and jam has occurred.
Remedy:	• Jam Occurrence Location 1) Check if there is any substance on duplex path. Remove it. 2) Clean the surface of the duplex roller-3. If it is broken or deformed, replace it(JC66-03495A). 3) Enter SVC mode. Execute duplex motor2 test. (Diagnostics > Engine Diagnostics > Engine Test Routines > Duplex2 Motor Forward) • If the motor operation is abnormal, check the motor connection. If the connection is OK, replace the motor(JC93-00301A) from the duplex unit. 4) Check if the duplex ready sensor actuator is assembled correctly. If the spring is defective, replace it(6107-003137). 5) If the regi roller does not rotate, check the regi clutch operation. • Enter SVC mode. Execute the regi clutch test. If the regi clutch is defective, replace it(JC47-00039A).

Error code:	M2-2313
Display:	Paper jam at the inside of duplex path
Description:	Paper is not reached to the regi sensor and jam has occurred.
Remedy:	• Jam Occurrence Location 1) Check if there is any substance on duplex path. Remove it. 2) Clean the surface of the duplex roller-3. If it is broken or deformed, replace it(JC66-03495A). 3) Enter SVC mode. Execute duplex motor2 test. (Diagnostics > Engine Diagnostics > Engine Test Routines > Duplex2 Motor Forward) • If the motor operation is abnormal, check the motor connection. If the connection is OK, replace the motor(JC93-00301A) from the duplex unit.

Error code:	M2-2414
Display:	Paper jam at the inside of duplex path
Description:	Paper is not passed the regi sensor and jam has occurred.
Remedy:	• Jam Occurrence Location 1) Check if there is any substance on simplex path. Remove it. 2) Check the troubleshooting related to ITB unit. 3) Check the troubleshooting related to fuser unit.

Error code:	M3-1113
Display:	Paper jam in exit area.
Description:	Paper jam has occurred around the fuser unit.
Remedy:	• Jam Occurrence Location 1) Open the side cover. Remove the jammed paper. 2) If the paper in the tray is not proper, replace it. 3) If this jam occurs continually, check the following. a) Remove the fuser unit. Check if fuser unit has any defective part. Replace the fuser unit(JC91-01120A(110V) / JC91-01121A(220V)) b) Check if the exit sensor is assembled correctly. If it is defective, replace it(0604-001415).

Error code:	M3-1114
Display:	Paper jam in exit area.
Description:	Paper jam has occurred around the fuser unit.
Remedy:	• Jam Occurrence Location 1) Open the side cover. Remove the jammed paper. 2) If the paper in the tray is not proper, replace it. 3) If this jam occurs continually, check the following. a) Remove the fuser unit. Check if fuser unit has any defective part. Replace the fuser unit(JC91-01120A(110V) / JC91-01121A(220V)) b) Check if the exit sensor is assembled correctly. If it is defective, replace it(0604-001415). c) Check if the exit roller is assembled correctly. If it is defective, replace it(JC66-03507A).

Error code:	M3-2130
Display:	Output bin full Remove paper
Description:	Paper in output bin is full. Remove printed paper
Causes:	The machine detected that the output tray has got full or the bin-full sensor is defective.
Remedy:	1) Remove the paper on the output tray. (The maximum loading capacity is 150 sheets based on standard paper (80 g/m²).) 2) Check if the Bin-full Sensor connector is connected properly. Reconnect it or replace the Bin-full sensor.

Error code:	S1-2411
Display:	Error #S1-2411 Turn off then on.
Description:	A communication error failure has occurred at HDD of main controller.
Causes:	Hard Disk is not installed in the machine. / Hard Disk is defective.
Remedy:	1. Format the hard disk. 2. If the problem persists, replace the hard disk.

Error code:	S1-2433, S1-2443
Display:	System Failure: #S1-2433 . Call for service HDD System Failure # : Call for service
Description:	System memory is corrupted. / Unexpected S/W error has occurred.
Remedy:	1) Enter the SVC(tech) mode. Select “System Recovery” in Service Function menu. 2) Execute the hard disk format and firmware re-installation. 3) If the problem persists, replace the HDD(JC59-00035A).

Error code:	S1-2434, S1-2436
Display:	HDD Error #. Check users guide.
Description:	HDD partition or memory is full.
Remedy:	• S1-2434 : Addresses in Address book / User data in User profile • S1-2436 : System Logs • S1-2438/2439 : Printing Error / No Paper in Tray 1) Enter SVC mode. Select “Hard Disk Maintenance” in Service Function menu. 2) Execute hard disk format. 3) If the problem persistss, replace the HDD(JC59-00035A).

Error code:	S1-2438, S1-2439
Display:	HDD Error #. Check users guide.
Description:	HDD partition or memory is full.
Remedy:	• S1-2434 : Addresses in Address book / User data in User profile • S1-2436 : System Logs • S1-2438/2439 : Printing Error / No Paper in Tray 1) Enter SVC mode. Select “Hard Disk Maintenance” in Service Function menu. 2) Execute hard disk format. 3) If the problem persistss, replace the HDD(JC59-00035A).

Error code:	S1-2444, S1-2445
Display:	System Failure: #S1-2433 . Call for service HDD System Failure # : Call for service
Description:	System memory is corrupted. / Unexpected S/W error has occurred.
Remedy:	1) Enter the SVC(tech) mode. Select “System Recovery” in Service Function menu. 2) Execute the hard disk format and firmware re-installation. 3) If the problem persists, replace the HDD(JC59-00035A).

Error code:	S1-2446, S1-2447
Display:	System Failure: #S1-2433 . Call for service HDD System Failure # : Call for service
Description:	System memory is corrupted. / Unexpected S/W error has occurred.
Remedy:	1) Enter the SVC(tech) mode. Select “System Recovery” in Service Function menu. 2) Execute the hard disk format and firmware re-installation. 3) If the problem persists, replace the HDD(JC59-00035A).

Error code:	S1-2511, S1-2521, S1-2523
Display:	MSOK System Failure: #S1-2511. Turn off then on MSOK Failure: #S1-2521. Call for service PPM data is incorrect. Call for service & change MSOK MSOK Failure: #. Call for service & change MSOK
Description:	MSOK has a problem.
Remedy:	1) Turn the machine off and on. 2) If the problem persists, turn the machine off again. 3) Remove the rear cover. 4) Check if the MSOK is inserted correctly. Remove and reinstall it. 5) If the problem persists, replace the main board(JC92-02516).

Error code:	S1-2530, S1-2540
Display:	MSOK System Failure: #S1-2511. Turn off then on MSOK Failure: #S1-2521. Call for service PPM data is incorrect. Call for service & change MSOK MSOK Failure: #. Call for service & change MSOK
Description:	MSOK has a problem.
Remedy:	1) Turn the machine off and on. 2) If the problem persists, turn the machine off again. 3) Remove the rear cover. 4) Check if the MSOK is inserted correctly. Remove and reinstall it. 5) If the problem persists, replace the main board(JC92-02516).

Error code:	S2-1211
Display:	Engine System Failure #S2-1211: Turn off then on.
Description:	Power chip on main board is defective.
Causes:	Communication error between the ASIC on main board and microcontroller IC has occurred.
Remedy:	1) Turn the machine off then on. 2) If the problem persists, replace the main board.

Error code:	S2-331C
Display:	Calibrating... Please Wait
Description:	Printing Job is stopped because of high temperature inside machine.
Remedy:	1) Open the side cover. Cool the machine. And close the side cover. 2) If the problem persists, enter SVC mode. Execute the temperature sensor test. (Diagnostics > Engine Diagnostics > EngineTest Routines > 109-0013 Outer Temperature) 3) Check the temperature sensor connection. If the connection is OK, measure the resistor value of the sensor. 4) If the value is not in 47.5KOm - 52.5KOm (at 25C), replace the sensor(JC32.00015A) 5) If the temperature sensor is OK, remove the rear cover. 6) Replace the main board(JC92-02516A). 7) Assemble the rear cover. Turn the machine on.

Error code:	S2-4210
Display:	Front door is open. Close it.
Description:	Front door is open. Close it.
Causes:	Front cover or Side cover is opened.
Remedy:	1) Close the front cover correctly. 2) Check if the cover open sensor connector is connected properly. Reconnect it. 3) If the sensor is defective, replace it.

Error code:	S2-4410
Display:	Right door is open. Close it.
Description:	Right door is open. Close it.
Causes:	Front cover or Side cover is opened.
Remedy:	1) Close the side cover correctly. 2) Check if the cover open sensor connector is connected properly. Reconnect it. 3) If the sensor is defective, replace it.

Error code:	S2-5111, S2-5112, S2-5120, S2-5131
Display:	Failed to adjust the color registration
Description:	ACR error has occurred.
Remedy:	1) Execute “ACR calibration” manually. 2) Check if the ACR sensor is defective and connector is connected properly. 3) Check the image density and the belt of the ITB unit. 4) If the problem persists, main board.

Error code:	S2-5132, S2-5133, S2-5135
Display:	Failed to adjust the color registration
Description:	ACR error has occurred.
Remedy:	1) Execute “ACR calibration” manually. 2) Check if the ACR sensor is defective and connector is connected properly. 3) Check the image density and the belt of the ITB unit. 4) If the problem persists, main board.

Error code:	S2-5136, S2-5161, S2-5164
Display:	Failed to adjust the color registration
Description:	ACR error has occurred.
Remedy:	1) Execute “ACR calibration” manually. 2) Check if the ACR sensor is defective and connector is connected properly. 3) Check the image density and the belt of the ITB unit. 4) If the problem persists, main board.

Error code:	S2-5210, S2-5220, S2-5231
Display:	Failed to adjust the OPC Feed forward control
Description:	OPC feed forward control failure has occurred.
Remedy:	1) Replace the ITB unit.

Error code:	S2-5240, S2-5250
Display:	Failed to adjust the OPC Feed forward control
Description:	OPC feed forward control failure has occurred.
Remedy:	1) Replace the ITB unit.

Error code:	S3-3121
Display:	Scanner Locked
Description:	CIS unit in the scanner does not move.
Causes:	Scanner lock error has occurred. CIS does not move.
Remedy:	1) Check if the CIS unit moves when turning the machine off then on. 2) Check if the CIS cable is connected correctly. Reconnect it. 3) If the CIS unit is defective, replace it. 4) Check if there is any defective part in the scanner. Find and replace it. 5) If the problem persists, replace the main board.

Error code:	S3-3211
Display:	Scan System Failure #S3-3211: Turn off then on.
Description:	Scan System Failure #S3-3211: Turn off then on.
Causes:	ADF is not connected or communication error occurs with CIP6 board.
Remedy:	1) Turn the machine off then on. If the problem persists, check the following: 2) Turn the machine off again. 3) Remove the scan rear cover. Check if the connector on scan joint board is connected correctly. 4) Remove the ADF rear cover. Check if the connector on ADF board is connected correctly. 5) If the connection is OK, replace the ADF board.

Error code:	S5-3111
Display:	UI System Failure #S5-3111:Turn off then on.
Description:	UI System Failure #S5-3111:Turn off then on.
Causes:	Main board has critical problem which make its lockup or USB connection between main board and OPE has some problem.
Remedy:	1) Turn off and turn on. And check if the problem disappears. a) If yes, go to step 2)-a). b) If no, go to step 2)-b). 2) Check the following procedure. a) Print the Error Information Report. . Service Mode - General - Print Reports - Error Information . Check the error code which is printed on the report. - If S5-3111 has occurred, go to step 4). - If S5-3112 has occurred, go to step 5)-c). - If S5-3113 has occurred, go to step 5)-d). b) Enter into System Recovery Mode. . How to enter System Recovery Mode : Turn on the machine with side cover open and power button on OPE is pressed state. . Check if entering System Recovery Mode is possible or not. - If entering System Recovery Mode is successful, go to step 3). - If entering System Recovery Mode fails, go to step 5)-d). 3) Execute the System Recovery. • Insert USB memory stick which has recovery one rom and execute recovery(HDD format). • Check if the problem disappears after system recovery(format complete). - If yes, go to step 4). - If no, go to step 5)-c). 4) Execute the firmware update. • Check if the problem disappears after one rom update. - If the problem disappears, go to step 5)-a). - If the problem happens sometimes, go to step 5)-b). 5) Check the following procedure. a) No more action is required because machine is recovered from S5-3111 error state. Please monitor the machine if S5-3111 happens again. b) Detailed analysis is required. Please capture the log and send it to development team in HQ. c) It seems that HDD or main board has some problem. Please replace HDD or main board with new one and check if the problem disappears. d) It seems that there is some critical issue in the USB connection between main board and OPE. Please try below steps. i) If WiFi module is installed, replace WiFi module with new one. ii) Check USB cable state between main board and OPE. iii) Replace the main board with new one. iv) Replace the OPE board with new one.

Error code:	S6-3122
Display:	Network cable is disconnected. Check it.
Description:	Network cable is disconnected. Check it.
Causes:	Network cable is disconnected.
Remedy:	1) Check if the green LED of the network port is on. 2) If not, unplug and reconnect the network cable. 3) If the problem persists, replace the main board(JC92-02742A).

Error code:	S6-3123
Display:	This IP address conflicts with that of other system. Check it.
Description:	This IP address conflicts with that of other system. Check it.
Causes:	Network has some problem. (IP address conflicts with that of other system. / Communication error / There is no response when checking the ping test.)
Remedy:	Change the machine’s IP address. • Execute the Samsung Easy Printer Manager program. (Device setting > Network > IP address). Change the IP address. • In case of DHCP or Bootp, reboot the machine to receive a new IP address.

Error code:	S6-3128
Display:	802.1x authentication failed. Please Contact the System Administrator
Description:	There is no response when checking the ping test. ID or Password is incorrect.
Causes:	Network error. ( A authenticator(eg switch) rejected authentication. / There is no response when checking the ping test.)
Remedy:	1) Change the IP adredd (Machine Setup > Network Setting > Login > TCP/IP > Select the network protocol > IP Setting 2) Inut the Network Login ID and Password correctly.

Error code:	S7-1110
Display:	Failure: #S7-1110. Turn off then on
Description:	Engine System Failure: #S7-1110. Turn off then on
Causes:	24V power is abnormal.
Remedy:	1) Check the 24V pin on SMPS board. If it is abnormal, replace the SMPS board. 2) Check the related cable. 3) If the SMPS is normal, replace the main board.

Error code:	S7-1210
Display:	Failure: #S7-1210. Turn off then on
Description:	Engine System Failure: #S7-1110. Turn off then on
Causes:	5V power is abnormal.
Remedy:	1) Check the 5V pin on SMPS board. If it is abnormal, replace the SMPS board. 2) Check the related cable. 3) If the SMPS is normal, replace the main board.

Error code:	S7-2110
Display:	Fuser Failure: #S7-2110. Turn off then on
Description:	Fuser Failure: #S7-2110. Turn off then on
Causes:	Heater control relay is abnormal.
Remedy:	1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) If the problem persists, replace the Fuser unit(110V : JC91-01158A, 220V : JC91-01157A).

Error code:	S8-1111
Display:	HVPS Failure: #S8-1111. Turn off then on.
Description:	24V power for HVPS board1 is less than 1.6V.
Remedy:	1) Turn the machine off. 2) Remove the left cover. 3) Replace the HVPS board1(JC44-00220A). 4) Assemble the left cover. Turn the machine on.

Error code:	S8-1112
Display:	HVPS Failure: #S8-1111. Turn off then on.
Description:	24V power for HVPS board2 is less than 1.6V.
Remedy:	1) Turn the machine off. 2) Remove the rear cover. 3) Replace the HVPS board2(JC44-00221A). 4) Assemble the rear cover. Turn the machine on.

Error code:	U1-2113, U1-2119
Display:	Fuser Unit Failure: #U1-2113. Fuser Unit Failure: #U1-2119.
Description:	Fuser Unit Failure: #U1-2113. Fuser Unit Failure: #U1-2119.
Causes:	The thermistor can’t measure temperature. The hear-roller will not heat-up.
Remedy:	• U1–2113 : Error occurs at non-contact type Thermistor • U1–2119 : Error occurs at contact type Thermistor 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) Remove the fuser unit. After opening the jam cover, check if jammed or wrapped paper is in the fuser unit. 3) If the problem persists, check the following: a) Check if the Halogen lamp (110V : 4713–001632 / 220V : 4713–001633) is broken or disconnected. b) Check if the AC connection of the Halogen lamp is disconnected or contaminated. c) Check if the thermistat(4712-001098) is disconnected. d) Check if the contact type thermistor(1404–001567) or Non-contact type thermistor(1404–001453)is broken. 4) If the problem persists, replace the Fuser unit(220V : JC91–01163A / 110V : JC91–01164A). 5) If the problem persists, replace the main board(JC92–02746A) or FDB board(220V : JC44-00211A, 110V : JC44-0021A)or SMPS(220V : JC44-00100C, 110V : JC44-00093C)

Error code:	U1-2115
Display:	Fuser Unit Failure: #U1-2115. Turn off then on.
Description:	Fuser Unit Failure: #U1-2115. Turn off then on.
Causes:	The pressure control unit(Cam unit)of the fuser is abnormal.
Remedy:	1) Turn the machine off then open the side cover. 2) Remove and re-install the fuser unit, then turn the machine on. 3) If the problem persists, check the following : a) When the side-cover closes, check if the operation sound of the pressure control unit occurs. b) Check if the parts of the pressure control unit are abnormal. - Check if the shape of the CAM-REAR(JC66-03299A)) is broken. - Check if there are abnormal parts of the pressure control unit. c) Check if the fuser-motor is abnormal via SVC mode. 4) If the problem persists, replace the Fuser unit(110V : JC91-01158A, 220V : JC91-01157A). 5) If the problem persists, replace the pressure control unit or cam-motor or Main board(JC92-02742A).

Error code:	U1-2132, U1-2135
Display:	Fuser Unit Failure: #U1-2132. Fuser Unit Failure: #U1-2135.
Description:	Fuser Unit Failure: #U1-2132. Fuser Unit Failure: #U1-2135.
Causes:	Temperature of the fuser rises abnormally.
Remedy:	• U1–2132 : Error occurs at non-contact type Thermistor • U1–2135 : Error occurs at contact type Thermistor 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?) 3) Remove the fuser unit. After opening the jam cover, check jammed or wrapped paper is in the fuser unit. 4) If the problem persists, Check the following: a) Check if the Halogen lamp (110V : 4713–001632 / 220V : 4713–001633) is broken or disconnected. b) Check if the AC connection of the Halogen lamp is disconnected or contaminated. c) Check if the thermistat(4712-001098) is disconnected. d) Check if the contact type thermistor(1404–001567) or Non-contact type thermistor(1404–001453) is broken. 5) If the problem persists, replace the Fuser unit(220V : JC91–01163A / 110V : JC91–01164A). 6) If the problem persists, replace the main board(JC92–02746A) or FDB board(220V : JC44-00211A, 110V : JC44-0021A)or SMPS(220V : JC44-00100C, 110V : JC44-00093C)

Error code:	U1-2316, U1-2317
Display:	Fuser Unit Failure: #U1-2316. Fuser Unit Failure: #U1-2317.
Description:	Fuser Unit Failure: #U1-2316. Fuser Unit Failure: #U1-2317
Causes:	Temperature of the fuser changes abnormally
Remedy:	• U1–2316 : Error occurs at non-contact type Thermistor • U1–2317 : Error occurs at contact type Thermistor 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?) 3) If the problem persists, Check the following: a) Check if the Halogen lamp (110V : 4713–001632 / 220V : 4713–001633) is broken or disconnected. b) Check if the AC connection of the Halogen lamp is disconnected or contaminated. c) Check if the thermistat(4712-001098) is disconnected. d) Check if the contact type thermistor(1404–001567) or Non-contact type thermistor(1404–001453) is broken. 4) If the problem persists, replace the Fuser unit(220V : JC91–01163A / 110V : JC91–01164A). 5) If the problem persists, replace the main board(JC92–02746A) or FDB board(220V : JC44-00211A, 110V : JC44-0021A)or SMPS(220V : JC44-00100C, 110V : JC44-00093C)

Error code:	U1-233x
Display:	Fuser Unit Failure: #U1-233x. Turn off then on.
Description:	The temperature of fuser unit is low. (Low Heat Error)
Remedy:	1) Turn the machine off then on. 2) Turn the machine off. Re-install the fuser unit. Then turn the machine on. 3) If the problem persists, remove the fuser unit. 4) Check if the paper is curled on the fuser belt. 5) If yes, replace the fuser unit. If not, check the followings. a) Check if the input voltage is normal. b) Remove 8 screws. Remove left/right/top cover. c) Remove 8 screws. Remove the bracket. d) Check if the thermostat(4712-001093) is connected. e) Check if the center and side lamps(4713-001651 : 110V / 4713-001655 : 220V) are in short status. (Measure the resistance value between the common-center and common-side.) f) Check if the thermistor is defective. 6) If the step5 has no problem, replace the fuser unit(JC91-01120A(110V) / JC91-01121A(220V)). 7) If the problem persists, replace these parts in regular sequence. • Fuser Drive Board : JC44-00210A(110V) / JC44-00211A(220V) • Main board : JC92-02516A • SMPS board : JC44-00149B(110V) / JC44-00150B(220V)

Error code:	U2-6121, U2-6122, U2-6123
Display:	LSU Failure #U2-6121: Turn off then on. LSU Failure #U2-6122: Turn off then on. LSU Failure #U2-6123: Turn off then on.
Description:	LSU Failure #U2-6121: Turn off then on. LSU Failure #U2-6122: Turn off then on. LSU Failure #U2-6123: Turn off then on.
Causes:	LSU motor does not operate or it operates abnormally. Motor ready signal is abnormal.
Remedy:	1) Turn the machine off then on. Check for the LSU motor operation sound during warm-up. 2) Print a demo page to check that the machine operates normally. 3) If the problem persists, check the following : a) If the LSU motor makes a sound, i) Enter SVC mode to check the LSU motor ready signal. ( Diagnostics > Engine Diagnostics > Engine Test Routines) ii) Select “LSU Motor1 Run Ready”. ( Diagnostics > Engine Diagnostics > Engine Test Routines > 110-0000) iii) Press ‘Start’ button. Check that the status has changed to ‘Executing -> Low -> High’. iv) If the status has not changed, the motor ready signal is abnormal. Replace the LSU. (JC97-04010A) (Refer to 3.3.5. LSU in chapter 3) b) If the LSU motor does not makes a sound, i) Turn the machine off and open the side cover. Unplug and reconnect the LSU cable. Check that the LSU motor make a sound after turning the machine on. ii) Turn the machine off and remove the rear cover. Unplug and reconnect the LSU cable on main board. Check that the LSU motor make a sound after turning the machine on. iii) If the LSU cable is defective, replace it. Check that the LSU motor make a sound after turning the machine on. iv) If the problem persists, replace the LSU(JC97-04010A).

Error code:	U2-7110
Display:	LSU Failure: #U2-7110. Turn off then on.
Description:	The control of LSU temperature is abnormal.
Remedy:	1) Turn the machine off then on. Check if the error message is disappeared. 2) If the problem persists, check the following : a) Turn the machine off and open the side cover. Unplug the LSU Cable(JC39-01791A : Flat cable) and Temperature Sensor cable. Reconnect them. b) Check that the error status after turning the machine on. c) If the LSU Cable(JC39-01791A : Flat cable) is defective, replace it. d) If the problem persists, replace the LSU(JC97-04073A).

Error code:	U3-3111, U3-3211
Display:	Original paper jam inside the scanner
Description:	Original jam has occurred around the scan in roller and regi roller.
Remedy:	1) Check if the pick up motor operates normally. a) Check if the paper jam has occurred on DADF tray. 2) Open the ADF cover. Remove the paper on Guide-Pick up Assy. 3) Check if the actuator and pick up assy operate normally. a) Check the operation of the regi sensor. b) If the regi sensor operation is OK, check the followings. i) Remove 1 screw and push the hook. ii) Release the Stacker by pulling it to the direction of arrow. iii) Release the rear cover. iv) Remove the Bracket Hinge. v) Remove the Cover-Open Assy. Remove 6 screws. And remove the bottom cover. vi) Check if the sensor and actuator are assembled correctly c) When lifting the pick up assy, check that 2 rollers contacts normally. 4) Check if there are any obstacles or contamination in the paper path. Remove it. 5) Close the ADF cover. 6) Open the DADF unit. Check if the reflection film is contaminated. Clean it. 7) Close the DADF unit.

Error code:	U3-3213, U3-3214
Display:	Original paper jam inside the scanner
Description:	Original paper jam in front of scanner. Original paper jam inside of scanner.
Causes:	A document jam was detected in the ADF unit.
Remedy:	1) Remove the jammed paper from ADF unit. 2) If the error persists, turn the machine off then on. 3) If the document jam occurs continually, open the ADF cover-top. Check if the ADF pick up roller is contaminated or worn out. Clean or replace it. 4) If the pick up roller is OK, check the followings. a) Check if the ADF motor is working normally. b) Check if the connector on the ADF joint board is connected correctly. 5) If the problem persists, replace the ADF unit.

Error code:	U3-3313, U3-3511,
Display:	Original paper jam inside the scanner
Description:	Original jam has occurred around the scan in roller and regi roller.
Remedy:	1) Check if the pick up motor operates normally. a) Check if the paper jam has occurred on DADF tray. 2) Open the ADF cover. Remove the paper on Guide-Pick up Assy. 3) Check if the actuator and pick up assy operate normally. a) Check the operation of the regi sensor actuator and feed out sensor actuator. b) If the regi sensor operation is OK, check the followings. i) Remove 1 screw and push the hook. ii) Release the Stacker by pulling it to the direction of arrow. iii) Release the rear cover. iv) Remove the Bracket Hinge. v) Remove the Cover-Open Assy. Remove 6 screws. And remove the bottom cover. vi) Check if the sensor and actuator are assembled correctly. 4) Check if there are any obstacles or contamination in the paper path. Remove it. 5) Close the ADF cover. 6) Open the DADF unit. a) Check if the reflection film is contaminated. Clean it. b) If the problem persists, check the followings. i) Open the DADF cover. ii) Pull the lever and release the pick up Assy. iii) Push and release the Stacker Assy. iv) Remove the Guide Pick Up Upper after removing 4 screws. v) Check if the sensor is assembled correctly. If the sensor is defective, replace it. 7) Check if the simplex scan sensor connector is connected correctly. 8) Close the DADF unit.

Error code:	U3-3314, U3-3511
Display:	Original paper jam inside the scanner
Description:	Original jam has occurred around the scan in roller and regi roller.
Remedy:	1) Check if the pick up motor operates normally. 2) Open the ADF cover. Check if the paper jam is occurred. 3) Pull the green lever of the Guide Exit Lower. Remove the jammed paper. 4) Check if there are any obstacles or contamination in the paper path. Remove it. 5) If the problem persists, check the followings. a) Remove the DADF Unit and white sponge. b) Open the Guide Exit Lower Assy. c) Check the sensor. d) Remove the screw. Check the sensor connection, If the connection is OK, replace the sensor. 6) Push the white bar. Check if it returns in original condition. 7) Close the DADF unit.

Error code:	U3-3513, U3-3514
Display:	Original paper jam inside the scanner
Description:	Original paper jam inside of scanner.
Causes:	Jam has occurred inside the DSDF unit.
Remedy:	1) Open the DSDF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the Regi. sensor and Regi actuator. Push and release the regi actuator. Check if the pick up module returns the original position. If the sensor is defective, replace it(0604–001393). 3) If the regi sensor is OK, check the scan 2 sensor and exit sensor. • If the scan 2 sensor is defective, replace it(0604–001381). • If the exit sensor is defective, replace it(6107–003581).

Error code:	U3-3711, U3-3713, U3-3714
Display:	Original paper jam in the exit area of scanner
Description:	Original jam has occurred inside the DADF unit.
Remedy:	1) Open the DADF cover. If there is a jammed paper, remove it. 2) If this error occurs continually, check the followings. a) Check if the exit actuator(JC66-03184A) operates normally. b) Check if the exit sensor cable is connected correctly. c) If the connection is OK, replace the exit sensor(0604-001393).

Деталь:	SENSOR
Парткод:	JC32-00015A

Деталь:	CLUTCH-ELECTRIC_G35
Парткод:	JC47-00038A

Деталь:	GUIDE-FEED LOWER
Парткод:	JC61-05100A

Деталь:	GUIDE-OPC TOP
Парткод:	JC61-05142A

Деталь:	GUIDE-FFC
Парткод:	JC61-05144A

Деталь:	SUPPORT-FINISHER EXIT
Парткод:	JC61-05165A

Деталь:	FRAME MAIN-PAPER SIZE
Парткод:	JC93-00574A

Деталь:	FRAME MAIN-COVER INNER
Парткод:	JC93-00577A

Деталь:	FRAME-MAIN DUCT FUSER
Парткод:	JC93-00588A

Деталь:	FRAME-GUIDE TONER CONTAINER
Парткод:	JC93-00590A

Деталь:	FRAME-GUIDE HARNESS FRONT
Парткод:	JC93-00591A

Деталь:	FRAME-MAIN SWITCH OPEN FRONT
Парткод:	JC93-00592A

Деталь:	FRAME-MAIN SHUTTER LSU
Парткод:	JC93-00594A

Деталь:	FRAME-MAIN DEVE GUIDE
Парткод:	JC93-00595A

Деталь:	FRAME-MAIN LSU PUSHER
Парткод:	JC93-00597A

Деталь:	GUIDE-HARNESS-REAR
Парткод:	JC61-05145A

Деталь:	PLATE-SUPPORT SCAN R
Парткод:	JC61-05177A

Деталь:	Roller-Feed
Парткод:	JC66-03446A

Деталь:	FRAME-MAIN CST RAIL
Парткод:	JC93-00593A

Деталь:	FRAME MAIN-DUCT TONER
Парткод:	JC93-00611A

Деталь:	EXIT GUIDE-2 DUP1 ASSY
Парткод:	JC90-01153A

Деталь:	PHOTO-INTERRUPTER
Парткод:	0604-001415
Цена:	240 ₽

Деталь:	PLATEN-HOLDER FFC SUB
Парткод:	JC97-04119A

Деталь:	PLATEN-HOLDER APS SUB
Парткод:	JC97-04117A

Деталь:	COVER-PLATEN FRONT LOW
Парткод:	JC63-03660A

Деталь:	COVER-INNER FRONT UPPER
Парткод:	JC63-03951A

Деталь:	COVER-INNER FRONT LOWER
Парткод:	JC63-03642A

Деталь:	COVER-RIGHT LOWER FRONT
Парткод:	JC63-03652A

Деталь:	COVER-RIGHT LOWER REAR
Парткод:	JC63-03651A

Samsung CLX-8640ND

Общие характеристики

Технология печати

Тип

Сканер

Тип устройства

Копир

Факс

Макс. формат

Размещение

Печать фотографий

Цветность печати

Телефон

Число страниц в месяц

Область применения

Принтер

Прямая печать

Двусторонняя печать

Печать без полей

Пигментные чернила

Количество цветов

Макс, разрешение для ч/б печати

Скорость ч/б печати

Время выхода первого отпечатка

Копир

Время выхода первой копии

Макс, количество копий за цикл

Значение масштаба

Макс, разрешение (ч/б)

Сканер

Отправка изображения по e-mail

Стандарт TWAIN

Стандарт WIA

Макс. формат оригинала

Слайд-адаптер

Тип датчика сканера

Тип сканера

Макс, размер сканирования

Разрешение сканера

Расходные материалы

Количество картриджей

Печать на:

Факс

Цветной

Телефон

АОН

Спикерфон

Стандарт DECT

Проводная трубка

Беспроводная трубка

Автоответчик

Caller ID

Языки управления

Лотки

Емкость лотка ручной подачи

Подача бумаги

Финишер

Степлер

Сортер

Брошюровщик

Интерфейсы

USB

Ethernet (RJ-45)

Bluetooth

Wi-Fi

FireWire (IEEE 1394)

Инфракрасный порт

Устройство для чтения карт памяти

RS-232

LPT

Память/Процессор

Объем памяти

Макс, объем памяти

Емкость жесткого диска

Частота процессора

Процессор

Дополнительная информация

Экран

Диагональ дисплея

Работа от аккумулятора

Деталь:	ACTUATOR-PAPER_LENGTH
Парткод:	JC66-03209A

Деталь:	Motor BLDC
Парткод:	JC31-00123B
Цена:	3 700 ₽

Деталь:	GEAR-PULLEY IDLE EXIT 1 L8
Парткод:	JC66-03464A

Деталь:	GEAR-PULLEY IDLE-INSIDE EXIT2
Парткод:	JC66-03465A

Деталь:	GEAR-PULLEY IDLE OUTSIDE EXIT2
Парткод:	JC66-03466A

Деталь:	COVER-SIDE ROLLER TRANSFER2
Парткод:	JC95-01622A

Деталь:	BRACKET-GUIDE TRANSFER2
Парткод:	JC61-05038A

Деталь:	GUIDE-HOLDER TRANSFER2
Парткод:	JC61-05041A

Деталь:	SPONGE-DADF WHITE SHEET
Парткод:	JC63-03772A

Деталь:	CLUTCH-ELECTRIC
Парткод:	JC47-00033A
Цена:	1 200 ₽