Samsung ML-1440

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

лазерная

Макс. формат

Число страниц в месяц

12000

Скорость печати A4

Цветность печати

черно-белая

Общие характеристики
Тип	лазерный/светодиодный
Технология печати	лазерная
Цветность печати
Число страниц в месяц	12 000
Область применения	малый офис
Печать фотографий
Сканер
Копир
Макс. формат	A4
Тип устройства	Принтер
Принтер
Прямая печать
Двусторонняя печать
Макс, разрешение для ч/б печати
По Y	600
По X	600
Скорость ч/б печати
A4	14
Расходные материалы
Ресурс ч/б картриджа/тонера	6 000
Печать на:
Фотобумаге
Пленках
Этикетках
Лотки
Подача бумаги
Стандартная	270
Вывод бумаги
Стандартный	100
Интерфейсы
LPT
USB
Инфракрасный порт
Ethernet (RJ-45)
Память/Процессор
Объем памяти	8
Дополнительная информация
Поддержка ОС
Windows
DOS
Mac OS
Linux
Уровень шума
При работе	47
Габариты
Ширина	362
Высота	409
Глубина	250
Вес	11

Error code:	01
Display:	ERROR CONDITION INVALID HEAD
Description:	The ERROR light flashes.
Causes:	The printhead was replaced with one that is not a genuine Zebra™ printhead.
Remedy:	Install a genuine Zebra printhead.

Error code:	02
Display:	ERROR CONDITION RIBBON OUT
Description:	The printer stops; the ERROR light flashes.
Causes:	In thermal transfer mode, ribbon is not loaded or incorrectly loaded. In thermal transfer mode, the ribbon sensor is not detecting ribbon that is loaded incorrectly. In thermal transfer mode, media is blocking the ribbon sensor. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly.
Remedy:	Load ribbon correctly. 1. Load ribbon correctly. See Load Ribbon on page 64. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Load media correctly. See Load Media on page 58. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Print a sensor profile. See Print Sensor Profile on page 89. The ribbon out threshold (marked by the word RIBBON) is likely too high, above the black area that indicates where the ribbon is detected. 2. Calibrate the sensors or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73.

Error code:	03
Display:	WARNING RIBBON IN
Description:	The ERROR light flashes.
Causes:	Ribbon is loaded, but the printer is set for direct thermal mode.
Remedy:	Ribbon is not required with direct thermal media. If you are using direct thermal media, remove the ribbon. This error message will not affect printing. If you are using thermal transfer media, which requires ribbon, set the printer for Thermal Transfer mode. See Select Print Method on page 81.

Error code:	04
Display:	ERROR CONDITION PAPER OUT
Description:	The printer stops; the ERROR light flashes.
Causes:	The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded.
Remedy:	Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration.

Error code:	05
Display:	ERROR CONDITION HEAD OPEN
Description:	The printer stops; the ERROR light flashes.
Causes:	The printhead is not fully closed. The head open sensor is not working properly.
Remedy:	Replace the sensor.

Error code:	06
Display:	THERMISTOR FAULT
Description:	The ERROR light flashes.
Causes:	The printhead has a faulty thermistor.
Remedy:	Replace the printhead.

Error code:	07
Display:	WARNING HEAD COLD, THERMISTOR FAULT, ERROR CONDITION HEAD ELEMENT BAD
Description:	The printer stops; the ERROR light is on; the printer cycles through these three messages.
Causes:	The printhead data cable is not properly connected. The printhead has a faulty thermistor.
Remedy:	Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead.

Error code:	08
Display:	WARNING HEAD COLD
Description:	The printer prints while the ERROR light flashes.
Causes:	The printhead temperature is approaching its lower operating limit. The printhead data cable is not properly connected. The printhead has a faulty thermistor.
Remedy:	Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the printer to a warmer area. Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead.

Error code:	09
Display:	WARNING HEAD TOO HOT
Description:	The printer stops; the ERROR light flashes.
Causes:	The printhead is over temperature.
Remedy:	Allow the printer to cool. Printing automatically resumes when the printhead elements cool to an acceptable operating temperature.

Error code:	10
Display:	DEFRAGMENTING
Description:	The printer stops.
Causes:	The printer is defragmenting memory.
Remedy:	Caution • Do NOT turn off the printer power during defragmenting. Doing so can damage the printer. Allow the printer to finish defragmenting. If you get this error message frequently, check your label formats. Formats that write to and erase memory frequently may cause the printer to defragment often. Using properly coded label formats usually minimizes the need for defragmenting. If this error message does not go away, contact Technical Support. The printer requires service.

Error code:	11
Display:	ERROR CONDITION CUTTER JAM
Description:	The printer stops; the ERROR light flashes.
Causes:	Caution • The cutter blade is sharp. Do not touch or rub the blade with your fingers. The cutter blade is in the media path.
Remedy:	Turn off the printer power and unplug the printer. Inspect the cutter module for debris and clean as needed following the cleaning instructions in Clean the Cutter Module on page 135.

Error code:	12
Description:	General print quality issues
Causes:	The printer is set at the incorrect print speed. You are using an incorrect combination of labels and ribbon for your application. The printer is set at an incorrect darkness level. The printhead is dirty. Incorrect or uneven printhead pressure. The printhead is improperly balanced.
Remedy:	For optimal print quality, set the print speed to the lowest possible setting for your application via control panel, the driver, or the software. See Adjust Print Speed on page 79. You may want to perform the FEED Self Test on page 120. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. For optimal print quality, set the darkness to the lowest possible setting for your application via the control panel, the driver, or the software. See Adjust Print Darkness on page 78. You may want to perform the FEED Self Test on page 120 to determine the ideal darkness setting. Clean the printhead. See Clean the Printhead and Platen Roller on page 131. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Adjust the printhead balance.

Error code:	13
Description:	Long tracks of missing print on several labels
Causes:	Print element damaged.
Remedy:	Replace the printhead.

Error code:	14
Description:	Wrinkled ribbon
Causes:	Ribbon fed through the machine incorrectly. Incorrect burn temperature. Incorrect or uneven printhead pressure. Media not feeding properly; walking from side to side. The strip plate needs adjusting. The printhead needs vertical adjustment. The printhead is improperly balanced. The printhead and platen roller need to be realigned.
Remedy:	See Load Ribbon on page 64. Set the darkness to the lowest possible setting for good print quality. See Adjust Print Darkness on page 78. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Make sure that media is snug by adjusting the media guide, or call a service technician. Adjust the printhead balance.

Error code:	15
Description:	Printing too light or too dark over the entire label
Causes:	The media or ribbon is not designed for high-speed operation. You are using an incorrect combination of media and ribbon for your application. You are using ribbon with direct thermal media. Incorrect or uneven printhead pressure.
Remedy:	Replace supplies with those recommended for high-speed operation. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. Direct thermal media does not require ribbon. To check if you are using direct thermal media, perform the label scratch test in When to Use Ribbon on page 62. Set the pressure to the minimum needed. See Adjust Printhead Pressure on page 70.

Error code:	16
Description:	Smudge marks on labels
Causes:	The media or ribbon is not designed for high-speed operation.
Remedy:	Replace supplies with those recommended for high-speed operation.

Error code:	17
Description:	Misregistration/skips labels
Causes:	The printer is not calibrated. Improper label format.
Remedy:	Recalibrate the printer. Use correct label format.

Samsung ML-1440

Общие характеристики

Тип

Технология печати

Цветность печати

Число страниц в месяц

Область применения

Печать фотографий

Сканер

Копир

Макс. формат

Тип устройства

Принтер

Прямая печать

Двусторонняя печать

Макс, разрешение для ч/б печати

Скорость ч/б печати

Расходные материалы

Ресурс ч/б картриджа/тонера

Печать на:

Лотки

Подача бумаги

Вывод бумаги

Интерфейсы

LPT

USB

Инфракрасный порт

Ethernet (RJ-45)

Память/Процессор

Объем памяти

Дополнительная информация

Поддержка ОС

Уровень шума

Габариты

Ширина

Высота

Глубина

Вес

Коды ошибок

Описание

Парткод

Название

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку