Samsung ML-4510ND
Рейтинг
Модули
CASSETTE
DRIVE
FRAME-MAIN
FRAME-PICK UP
FRAME-RIGHT
Exit
DRIVE MAIN
Frame-Base
Frame-Middle
FRAME L
DUPLEX
OPE 4LINE
MAIN
COVER-TOP
Fuser
COVER-REAR
MP-Lower
FRAME-LEFT
COVER
Frame-Upper
MP-Upper
Детали Frame-Middle
| Деталь: | HANDLE-CASSETTE |
| Парткод: | JC64-00627A |
| Деталь: | CSP-FRAME-GUIDE PAPER DUMMY |
| Парткод: | JC81-08737A |
| Деталь: | CASSETTE-RETARD |
| Парткод: | JC90-01049A |
| Деталь: | Ring-E |
| Парткод: | 6044-000125 |
| Деталь: | BUSH-D6/L4 |
| Парткод: | JC61-00699A |
| Деталь: | CSP-SPRING TS |
| Парткод: | JC81-08640A |
| Деталь: | CSP-CAP RETARD |
| Парткод: | JC81-08479B |
| Деталь: | CSP-SHEET RETARD HCF |
| Парткод: | JC81-08641A |
| Деталь: | PAD-MP(PLUS) |
| Парткод: | JC69-00494A |
| Деталь: | CSP-PLATE KNOCK UP |
| Парткод: | JC81-08519A |
| Деталь: | CSP-FRAME CASSETTE |
| Парткод: | JC81-08488B |
| Деталь: | STOPPER-KNOCK UP |
| Парткод: | JC61-00832D |
| Деталь: | CSP-LOCKER CASSETTE |
| Парткод: | JC81-08494A |
| Деталь: | ROLLER-SUPPORT_CST |
| Парткод: | JC61-03882A |
| Деталь: | CASSETTE-GUIDE REAR PAPER |
| Парткод: | JC90-01050B |
| Деталь: | CASSETTE-SIDE LEFT |
| Парткод: | JC90-01048A |
| Деталь: | CASSETTE-SIDE RIGHT |
| Парткод: | JC90-01047A |
| Деталь: | CSP-DETECTOR PAPER SIZE |
| Парткод: | JC81-08485A |
| Деталь: | PLATE-LEVER |
| Парткод: | JC61-03206A |
| Деталь: | CSP-SHAFT LEVER |
| Парткод: | JC81-08636A |
| Деталь: | PLATE-LIFTING GEAR |
| Парткод: | JC61-01791A |
| Деталь: | CSP-GEAR LIFTING |
| Парткод: | JC81-08478A |
| Деталь: | CSP-GEAR RACK |
| Парткод: | JC81-08492A |
| Деталь: | GEAR-M_PINION 24 |
| Парткод: | JC66-01020A |
| Деталь: | GEAR-PICKUP DRIVE |
| Парткод: | JC66-01676A |
| Деталь: | CSP-GEAR IDLE RETARD |
| Парткод: | JC81-08477A |
| Деталь: | CSP-SPRING GROUND CASSETTE |
| Парткод: | JC81-08486A |
| Деталь: | CSP-LOCKER GUIDE REAR |
| Парткод: | JC81-08602A |
| Деталь: | Indicator-Paper |
| Парткод: | JC64-00628A |
| Деталь: | Ring-E |
| Парткод: | 6044-000231 |
| Деталь: | SCREW-TAPPING |
| Парткод: | 6002-000440 |
| Деталь: | SCREW-TAPTYPE |
| Парткод: | 6003-000269 |
| Деталь: | MEA UNIT-ROLLER PU |
| Парткод: | JC97-02259A |
| Цена: | 240 ₽ |
| Деталь: | Резиновый элемент на ролик захвата бумаги из обходного лотка |
| Парткод: | JC73-00295A |
| Цена: | 380 ₽ |
| Деталь: | Резина ролика захвата бумаги |
| Парткод: | CET7911 |
| Деталь: | FRAME-TERMINAL |
| Парткод: | JC93-00370A |
| Деталь: | BUSH-D6/L4 |
| Парткод: | JC61-00699A |
| Деталь: | COVER-SMPS |
| Парткод: | JC95-01410A |
| Деталь: | DRIVE MAIN |
| Парткод: | JC93-00348A |
| Деталь: | FDB-PETREL V1 |
| Парткод: | JC44-00203A |
| Деталь: | SMPS-V1 |
| Парткод: | JC44-00091C |
| Деталь: | HOLDER-COVER OPEN |
| Парткод: | JC61-04245A |
| Деталь: | PBA-COVER OPEN SENSOR |
| Парткод: | JC92-02371A |
| Деталь: | FRAME-MIDDLE |
| Парткод: | JC93-00366A |
| Деталь: | FRAME-GUIDE OPC LEFT |
| Парткод: | JC93-00362A |
| Деталь: | FRAME-GUIDE OPC RIGHT |
| Парткод: | JC93-00363A |
| Деталь: | ROLLER-FEED_DRIVE |
| Парткод: | JC66-02965A |
| Деталь: | PMO-PICK UP CLUTCH SUB |
| Парткод: | JB72-00845A |
| Деталь: | MP-UPPER |
| Парткод: | JC90-01079A |
| Деталь: | MP-LOWER |
| Парткод: | JC90-01081A |
| Деталь: | PLATE-FEED IDLE |
| Парткод: | JC61-04226A |
| Деталь: | Ring-E |
| Парткод: | 6044-000125 |
| Деталь: | PULLEY-DUPLEX |
| Парткод: | JC66-02902A |
| Деталь: | BUSH-D6/L4 |
| Парткод: | JC61-00699A |
| Деталь: | ROLLER-DUPELX_DRIVE |
| Парткод: | JC66-02966A |
| Деталь: | HARNESS-DUP & UPLIMIT_SEN |
| Парткод: | JC39-01443A |
| Деталь: | HOLDER-PICK UP |
| Парткод: | JC61-04255A |
| Деталь: | ADJUST-DUPLEX OPEN |
| Парткод: | JC70-00598A |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | 0604-001325 |
| Деталь: | Spring-CS |
| Парткод: | 6107-002854 |
| Деталь: | GROUND-DUPLEX BRACKET |
| Парткод: | JC63-02982A |
| Деталь: | BRUSH-PICK |
| Парткод: | JC67-00468A |
| Деталь: | GEAR-RETARD IDLE A |
| Парткод: | JC66-02895A |
| Деталь: | Actuator-Duplex |
| Парткод: | JC66-02906A |
| Деталь: | MEA UNIT-ROLLER PU |
| Парткод: | JC97-02259A |
| Цена: | 240 ₽ |
| Деталь: | MEA UNIT-IDLE FORWARD |
| Парткод: | JC97-02292A |
| Деталь: | GEAR-M_PU JOINT |
| Парткод: | JC66-00943A |
| Деталь: | HOUSING-PICKUP |
| Парткод: | JC61-04235A |
| Деталь: | ACTUATOR-PAPER EMPTY |
| Парткод: | JC66-02905A |
| Деталь: | GEAR-M_IDLE PU |
| Парткод: | JC66-00940A |
| Деталь: | HOLDER-ACTUATOR EMPTY |
| Парткод: | JC61-04259A |
| Деталь: | Spring-TS |
| Парткод: | 6107-002855 |
| Деталь: | MEA UNIT-GEAR ONE WAY |
| Парткод: | JC97-02291A |
| Деталь: | FRAME-GUIDE CASSETTE RIGHT |
| Парткод: | JC93-00361A |
| Деталь: | DRIVE-FEED |
| Парткод: | JC93-00350A |
| Деталь: | Spring-ES |
| Парткод: | 6107-001259 |
| Деталь: | DRIVE FUSER-BRACKET |
| Парткод: | JC93-00351A |
| Деталь: | GUIDE-FUSER R |
| Парткод: | JC61-04262A |
| Деталь: | HOLDER-CONNECTOR SCF |
| Парткод: | JC61-04242A |
| Деталь: | HARNESS-SCF |
| Парткод: | JC39-01441A |
| Деталь: | HOLDER-FOOT_LOWER |
| Парткод: | JC61-03946A |
| Деталь: | GEAR-RETARD IDLE B |
| Парткод: | JC66-02886A |
| Деталь: | Washer-Plain |
| Парткод: | 6031-001255 |
| Деталь: | GEAR-RETARD RDCN |
| Парткод: | JC66-02885A |
| Деталь: | FRAME-RIGHT |
| Парткод: | JC61-04285A |
| Деталь: | Saddle |
| Парткод: | 6502-001132 |
| Деталь: | GUIDE-CASSETTE R |
| Парткод: | JC61-04265A |
| Деталь: | SWITCH-SIGNAL |
| Парткод: | JC34-00001A |
| Деталь: | HARNESS-CST_JOINT |
| Парткод: | JC39-01440A |
| Деталь: | BRACKET-GROUND CASSETTE |
| Парткод: | JC61-04289A |
| Деталь: | Ring-CS |
| Парткод: | 6044-000001 |
| Деталь: | LEVER-PICK_UP |
| Парткод: | JC66-02627A |
| Деталь: | Spring-ES |
| Парткод: | 6107-001517 |
| Деталь: | DRIVE EXIT |
| Парткод: | JC93-00349A |
| Деталь: | EXIT-ROLLER DUPLEX |
| Парткод: | JC90-01092A |
| Деталь: | GUIDE-DEFLECTOR |
| Парткод: | JC61-03891A |
| Деталь: | ROLLER-EXIT_UPPER |
| Парткод: | JC66-02663A |
| Деталь: | ROLLER-EXIT_LOWER |
| Парткод: | JC66-02664A |
| Деталь: | BRUSH-ANTISTATIC |
| Парткод: | JC67-00295A |
| Деталь: | GEAR-M_EXIT UPPER |
| Парткод: | JC66-01017A |
| Деталь: | GEAR-M_EXIT LOWER |
| Парткод: | JC66-01018A |
| Деталь: | Gear-M-Exit DUP Z21 |
| Парткод: | JC66-00854A |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | 0604-001325 |
| Деталь: | BUSH-8/5 |
| Парткод: | JC61-00426A |
| Деталь: | Ring-E |
| Парткод: | 6044-000129 |
| Деталь: | FRAME-CAP EXIT |
| Парткод: | JC61-04283A |
| Деталь: | FRAME-EXIT |
| Парткод: | JC61-04282A |
| Деталь: | CAP-ROLLER_EXIT |
| Парткод: | JC67-00477A |
| Деталь: | MOTOR BLDC-TYPE4 |
| Парткод: | JC31-00150A |
| Деталь: | Motor BLDC |
| Парткод: | JC31-00144A |
| Цена: | 3 200 ₽ |
| Деталь: | MOTOR DC |
| Парткод: | JC31-00078A |
| Цена: | 1 600 ₽ |
| Деталь: | CLUTCH-ELECTRIC |
| Парткод: | JC47-00033A |
| Цена: | 1 200 ₽ |
| Деталь: | Belt-Timing Gear |
| Парткод: | 6602-001581 |
| Деталь: | GEAR-FUSER RDCN A |
| Парткод: | JC66-02874A |
| Деталь: | GEAR-FUSER RDCN B |
| Парткод: | JC66-02875A |
| Деталь: | GEAR-OPC DRIVE |
| Парткод: | JC66-02856A |
| Деталь: | FRAME-RIGHT |
| Парткод: | JC93-00367A |
| Деталь: | FRAME-LEFT |
| Парткод: | JC93-00364A |
| Деталь: | DUPLEX |
| Парткод: | JC90-01076A |
| Деталь: | FRAME-UPPER |
| Парткод: | JC93-00372A |
| Деталь: | Exit |
| Парткод: | JC90-01071A |
| Деталь: | BRACKET-SUPPORT FRAME |
| Парткод: | JC61-04269A |
| Деталь: | BRACKET-CROSS BAR F |
| Парткод: | JC61-04270A |
| Деталь: | BRACKET-CROSS BAR R |
| Парткод: | JC61-04271A |
| Деталь: | FRAME-ROLLER TRANSFER |
| Парткод: | JC93-00393A |
| Цена: | 2 600 ₽ |
| Деталь: | PLATE-GUIDE TR |
| Парткод: | JC61-04280A |
| Деталь: | COVER-ACTUATOR |
| Парткод: | JC63-02986A |
| Деталь: | IPR-E-PLATE SAW(MCK2) |
| Парткод: | JC70-10232D |
| Деталь: | HOLDER-SAW |
| Парткод: | JC61-03906A |
| Деталь: | SPRING-ETC |
| Парткод: | 6107-002909 |
| Деталь: | Spring-TS |
| Парткод: | 6107-002869 |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | 0604-001325 |
| Деталь: | Actuator-Feed |
| Парткод: | JC66-02913A |
| Деталь: | FRAME-SENSOR CTD |
| Парткод: | JC93-00392A |
| Деталь: | HARNESS-CTD |
| Парткод: | JC39-01432A |
| Деталь: | SHEET-REGI |
| Парткод: | JC63-03097A |
| Деталь: | ROLLER-M-ADF IDLE |
| Парткод: | JC66-00461A |
| Деталь: | FRAME-REGI |
| Парткод: | JC93-00385A |
| Деталь: | FRAME-MIDDLE |
| Парткод: | JC61-04281A |
| Деталь: | SCREW-TAPTYPE |
| Парткод: | 6003-000196 |
| Деталь: | Spring-TS |
| Парткод: | 6107-001261 |
| Деталь: | GROUND-TR |
| Парткод: | JC63-02997A |
| Деталь: | GROUND-PLATE TR |
| Парткод: | JC63-02996A |
| Деталь: | GROUND-REGI ROLLER |
| Парткод: | JC63-03002A |
| Деталь: | ACTUATOR-REGI |
| Парткод: | JC66-02914A |
| Деталь: | PANEL UNIT, MFC9840CDW |
| Парткод: | JC91-01028A |
| Цена: | 15 900 ₽ |
| Деталь: | GUIDE-DUPLEX REAR |
| Парткод: | JC61-04267A |
| Деталь: | DUPLEX-GUIDE LOWER |
| Парткод: | JC90-01087A |
| Деталь: | Belt-Timing Gear |
| Парткод: | 6602-001588 |
| Деталь: | Belt-Timing Gear |
| Парткод: | 6602-001581 |
| Деталь: | FRAME-STOPPER CASSETTE |
| Парткод: | JC93-00369A |
| Деталь: | DUPLEX-FEEDER UPPER |
| Парткод: | JC90-01084A |
| Деталь: | GUIDE-DUPLEX UPPER |
| Парткод: | JC61-04221A |
| Деталь: | FRAME-PICK UP |
| Парткод: | JC93-00383A |
| Деталь: | Spring-TS |
| Парткод: | 6107-002857 |
| Деталь: | ROLLER-IDLE MP |
| Парткод: | JC66-02291A |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | 0604-001325 |
| Деталь: | HOLDER-HARNESS DRAW |
| Парткод: | JC61-04253A |
| Деталь: | HARNESS-FUSER_FR |
| Парткод: | JC39-01444A |
| Деталь: | DRIVE-DUPLEX |
| Парткод: | JC93-00352A |
| Деталь: | HOLDER-DUP LOWER |
| Парткод: | JC61-04249A |
| Деталь: | Spring-TS |
| Парткод: | 6107-002850 |
| Деталь: | SCREW-HEX |
| Парткод: | 6009-001492 |
| Деталь: | SCREW-TAPTYPE |
| Парткод: | 6003-000269 |
| Деталь: | OPE-4.3LCD |
| Парткод: | JC97-03941A |
| Деталь: | COVER-OPE 4.3 |
| Парткод: | JC63-03016A |
| Деталь: | COVER-W LAN |
| Парткод: | JC63-03015A |
| Деталь: | GROUND-LCD 4.3 |
| Парткод: | JC63-03005A |
| Деталь: | PLATE-LCD 4.3 |
| Парткод: | JC61-04279A |
| Деталь: | SEAL-4.3 LCD |
| Парткод: | JC62-00867A |
| Деталь: | LCD |
| Парткод: | JC07-00017A |
| Деталь: | BRACKET-LCD |
| Парткод: | JC61-04277A |
| Деталь: | PBA-OPE |
| Парткод: | JC92-02378A |
| Деталь: | SCREW-TAPTYPE |
| Парткод: | 6003-000269 |
| Деталь: | KEY-STOP |
| Парткод: | JC64-00564C |
| Деталь: | LENS-LED STATUS |
| Парткод: | JC67-00520A |
| Деталь: | KEY-POWER |
| Парткод: | JC64-00589C |
| Деталь: | KEY-POWER_HOLDER |
| Парткод: | JC64-00606A |
| Деталь: | PBA-OPE KEY |
| Парткод: | JC92-02379A |
| Деталь: | SCREW-TAPTYPE |
| Парткод: | 6003-000196 |
| Деталь: | COVER |
| Парткод: | JC95-01424A |
| Деталь: | OPE-4.3LCD |
| Парткод: | JC97-03941A |
| Деталь: | HVPS |
| Парткод: | JC44-00202A |
| Цена: | 4 500 ₽ |
| Деталь: | CASSETTE |
| Парткод: | JC90-01091A |
| Цена: | 7 100 ₽ |
| Деталь: | PBA-Main |
| Парткод: | JC92-02356F |
| Деталь: | FRAME |
| Парткод: | JC93-00390A |
| Деталь: | Fuser |
| Парткод: | JC91-01029A |
| Деталь: | LSU |
| Парткод: | JC97-03877A |
| Цена: | 4 800 ₽ |
| Деталь: | Cover-Top |
| Парткод: | JC95-01435A |
| Деталь: | Cover-Top |
| Парткод: | JC63-03012A |
| Деталь: | LEVER-EXPANDER |
| Парткод: | JC66-02903A |
| Деталь: | PMO-Stacker_RX |
| Парткод: | JC72-01367E |
| Деталь: | DAMPER-PAD ADF_R2 |
| Парткод: | JC66-00738A |
| Деталь: | DAMPER-LEVER STACKING |
| Парткод: | JC66-03030A |
| Деталь: | LEVER-STACKING |
| Парткод: | JC66-02904A |
| Деталь: | HARNESS-USB_HOST |
| Парткод: | JC39-01508A |
| Деталь: | Stopper-M-Fan80 |
| Парткод: | JC61-00667A |
| Деталь: | SCREW-TAPTYPE |
| Парткод: | 6003-000196 |
| Деталь: | GROUND-TOP |
| Парткод: | JC63-03004A |
| Деталь: | GUIDE-EXIT-UPPER |
| Парткод: | JC61-04179A |
| Деталь: | Holder-M-Idle Roller |
| Парткод: | JC61-00785A |
| Деталь: | Spring-TS |
| Парткод: | 6107-001159 |
| Цена: | 260 ₽ |
| Деталь: | PMO-Roller Upper DP |
| Парткод: | JC72-40981A |
| Деталь: | GEAR-CAM |
| Парткод: | JC66-02852A |
| Деталь: | LEVER-PRESSURE |
| Парткод: | JC66-02851A |
| Деталь: | GEAR-PR |
| Парткод: | JC66-02854A |
| Деталь: | GEAR-ACCEL |
| Парткод: | JC66-02853A |
| Деталь: | GEAR-EXIT-Z21 |
| Парткод: | JC66-02757A |
| Деталь: | Actuator-Exit |
| Парткод: | JC66-02850A |
| Деталь: | ROLLER-EXIT_F_UP |
| Парткод: | JC66-02973A |
| Деталь: | Holder-M_Rear_Lever |
| Парткод: | JC61-01625A |
| Деталь: | GUIDE-EXIT-LOWER |
| Парткод: | JC61-04178A |
| Деталь: | Roller-Pressure |
| Парткод: | JC66-02855A |
| Деталь: | SHAFT-CAM |
| Парткод: | JC66-02931A |
| Деталь: | THERMOSTAT |
| Парткод: | 4712-001093 |
| Деталь: | FUSER-THERMISTOR HOLDER |
| Парткод: | JC91-01048A |
| Деталь: | LAMP-HALOGEN |
| Парткод: | 4713-001573 |
| Деталь: | BRUSH-EXIT |
| Парткод: | JC67-00528A |
| Деталь: | HARNESS-FUSER_FU |
| Парткод: | JC39-01450A |
| Деталь: | Guide-INPUT |
| Парткод: | JC61-04195A |
| Деталь: | HOLDER-PLATE_BIAS |
| Парткод: | JC61-04174A |
| Деталь: | PLATE-BIAS PR |
| Парткод: | JC61-04182A |
| Деталь: | Spring-ES |
| Парткод: | 6107-002874 |
| Деталь: | DRUM-FUSER_BELT |
| Парткод: | JC66-02037B |
| Деталь: | BUSH-BELT |
| Парткод: | JC61-04168A |
| Деталь: | PLATE-PROTECTOR-LAMP |
| Парткод: | JC61-04184A |
| Деталь: | HOLDER-HARNESS_DUCT_L |
| Парткод: | JC61-04173A |
| Деталь: | Cover-Rear |
| Парткод: | JC63-02990A |
| Деталь: | BRACKET-P-HANDLE SCF |
| Парткод: | JC61-01404A |
| Деталь: | Spring-TS |
| Парткод: | 6107-001268 |
| Деталь: | HANDLE-REAR COVER |
| Парткод: | JC64-00420C |
| Деталь: | LOCKER-REAR L |
| Парткод: | JC64-00547A |
| Деталь: | HOLDER-LOCKER |
| Парткод: | JC61-03909B |
| Деталь: | LOCKER-REAR R |
| Парткод: | JC64-00548A |
| Деталь: | BRACKET-FEMALE |
| Парткод: | JC61-04276A |
| Деталь: | HARNESS-REAR_COVER_FU |
| Парткод: | JC39-01431A |
| Деталь: | FAN-DC |
| Парткод: | JC31-00088A |
| Деталь: | Guide-Rear |
| Парткод: | JC61-04266A |
| Деталь: | Spring-TS |
| Парткод: | 6107-002910 |
| Деталь: | SHAFT |
| Парткод: | JC70-20901A |
| Деталь: | ROLLER |
| Парткод: | JC72-20902A |
| Цена: | 500 ₽ |
| Деталь: | DAMPER-PAD ADF_R2 |
| Парткод: | JC66-00738A |
| Деталь: | GUIDE-EXIT |
| Парткод: | JC61-04268A |
| Деталь: | MP-LOWER |
| Парткод: | JC90-01081A |
| Деталь: | FRAME-MP LOWER |
| Парткод: | JC61-04234A |
| Деталь: | SHEET-MP_LOWER |
| Парткод: | JC63-03095A |
| Деталь: | MP-RETARD |
| Парткод: | JC90-01082A |
| Деталь: | HOUSING-MP RETARD |
| Парткод: | JC61-04237A |
| Деталь: | SPRING-ETC |
| Парткод: | 6107-002889 |
| Деталь: | HOLDER-MP RETARD |
| Парткод: | JC61-04257A |
| Деталь: | COUPLER-TORQUE_LIMITER |
| Парткод: | JC67-00465A |
| Деталь: | RUBBER-TL |
| Парткод: | JC73-00328A |
| Цена: | 430 ₽ |
| Деталь: | FAN-DC |
| Парткод: | JC31-00086A |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | 0604-001325 |
| Деталь: | GUIDE-FUSER L |
| Парткод: | JC61-04261A |
| Деталь: | FRAME-GUIDE CASSETTE LEFT |
| Парткод: | JC93-00360A |
| Деталь: | FRAME-TERMINAL FUSER |
| Парткод: | JC93-00371A |
| Деталь: | HOLDER-FOOT_LOWER |
| Парткод: | JC61-03946A |
| Деталь: | COVER-MP |
| Парткод: | JC63-02988A |
| Деталь: | COVER-RIGHT_DUMMY |
| Парткод: | JC63-02992A |
| Деталь: | COVER-CASSETTE REAR |
| Парткод: | JC63-03014A |
| Деталь: | Cover-Rear |
| Парткод: | JC95-01409A |
| Деталь: | COVER-MAILBOX |
| Парткод: | JC95-01407A |
| Деталь: | Cover-Top |
| Парткод: | JC95-01435A |
| Деталь: | COVER-LEFT |
| Парткод: | JC95-01406A |
| Деталь: | Cover-Front |
| Парткод: | JC95-01429A |
| Деталь: | MP-TRAY |
| Парткод: | JC90-01083A |
| Деталь: | COVER-RIGHT |
| Парткод: | JC95-01408A |
| Деталь: | COVER-LEFT |
| Парткод: | JC63-02987A |
| Деталь: | COVER-HANDLE_LEFT |
| Парткод: | JC63-02994A |
| Деталь: | Cover-Front |
| Парткод: | JC63-02989B |
| Деталь: | LOCKER-FRONT |
| Парткод: | JC64-00629A |
| Деталь: | Spring-CS |
| Парткод: | 6107-002960 |
| Деталь: | GUIDE-SIDE_MP_L |
| Парткод: | JC61-04334A |
| Деталь: | Gear-Pinion |
| Парткод: | JG66-40003A |
| Цена: | 260 ₽ |
| Деталь: | TRAY-MP EXTENSION |
| Парткод: | JC63-03036A |
| Деталь: | STACKER-MP |
| Парткод: | JC61-02804C |
| Деталь: | TRAY-MP |
| Парткод: | JC63-03035A |
| Деталь: | GUIDE-SIDE_MP_R |
| Парткод: | JC61-02645D |
| Деталь: | LINK-MP UPPER |
| Парткод: | JC66-02907A |
| Деталь: | RPR-Pad Cassette |
| Парткод: | JC73-00141A |
| Цена: | 80 ₽ |
| Деталь: | COVER-RIGHT |
| Парткод: | JC63-02991A |
| Деталь: | COVER-HANDLE_RIGHT |
| Парткод: | JC63-02993A |
| Деталь: | FRAME-UPPER |
| Парткод: | JC93-00372A |
| Деталь: | FRAME-LSU LOWER |
| Парткод: | JC61-04284A |
| Деталь: | CABLE CLAMP |
| Парткод: | 6502-001130 |
| Деталь: | PBA-ERASER |
| Парткод: | JC92-02373A |
| Деталь: | Holder-Eraser |
| Парткод: | JC61-04247A |
| Деталь: | HOLDER-CONNECTOR_DEVE |
| Парткод: | JC61-03903A |
| Деталь: | PBA-DEVE CRUM |
| Парткод: | JC92-02372A |
| Деталь: | HOLDER-CONNECTOR DEVE |
| Парткод: | JC61-04243A |
| Деталь: | DUCT-MAIN DEVE |
| Парткод: | JC67-00517A |
| Деталь: | FRAME-MP UPPER |
| Парткод: | JC61-04232A |
| Деталь: | DAMPER-MP_PICKUP |
| Парткод: | JC66-02970A |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | 0604-001325 |
| Деталь: | LATCH-STOPPER |
| Парткод: | JC66-02908A |
| Деталь: | STOPPER-PAPER MP |
| Парткод: | JC61-04231A |
| Деталь: | FRAME-MP UPPER_SUB |
| Парткод: | JC61-04233A |
| Деталь: | GUIDE-M_DOC SENSOR |
| Парткод: | JC61-00788A |
| Деталь: | MP-PICK UP |
| Парткод: | JC90-01080A |
| Цена: | 2 400 ₽ |
| Деталь: | BUSH-D6/L4 |
| Парткод: | JC61-00699A |
| Деталь: | Ring-E |
| Парткод: | 6044-000125 |
| Деталь: | Spring-ES |
| Парткод: | 6107-002863 |
Коды ошибок
A1-1110
A1-2110
A3-3312
C1-1110
C1-1120, C1-1140
C1-1311
C1-1411
C1-1512
C3-1110, C3-1120, C3-1140
C3-1312
C3-1330
C3-1512
H1-1210, H1-1310
H1-1222, H1-1322
H1-1230, H1-1240, H1-1330
H1-1252, H1-1352
H1-1253, H1-1353
H1-1340, H1-1430, H1-1440
H1-1410, H1-1510
H1-1422, H1-1522
H1-1452, H1-1552
H1-1453, H1-1553
H1-1530, H1-1540
H2-1100
H2-1101
H2-1102
H2-1200, H2-1300
H2-1302
H2-1710, H2-1711
H2-1720, H2-1721
H2-1730, H2-1731
H2-1750, H2-1751
H2-1752
H2-1753, H2-1A70
H2-1760, H2-1A80
H2-1800
H2-1A20
H2-1A32
H2-1A50
H2-1A62, H2-1A63
H2-4100
H2-4101, H2-4102
H2-4200, H2-4201, H2-4300
H2-4202, H2-4302
H2-4301, H2-4400, H2-4401
H2-4402, H2-4502
H2-4500, H2-4501
H2-4700, H2-4701
H2-4710, H2-4711
H2-4A20
H2-4A32, H2-4A35
H2-4A38, H2-4A3C
H2-4A50
M1-1110
M1-3122
M1-4111
M1-5112
M1-5612
M2-1110
M2-2210
M2-2310
M3-1110
M3-2130
S2-4210
S2-4610
S6-3123
S6-3128
U1-2115, U1-2116
U1-2117
U1-2320, U1-2330
U1-2340
U2-1111
U2-1113
Описание
| Error code: | A1-1110 |
| Display: | Error #A1-1110 Turn off then on |
| Description: | Main Motor Failure: #A1-1110. Turn off then on. Call for service if the problem persists |
| Causes: | After working the main BLDC motor, the Ready signal has not occurred within 1 sec. |
| Remedy: | 1) Turn the machine off then on. If the error persists, refer to the following. 2) Check if the motor connector on the main board is connected properly. Reconnect it. 3) OPC coupler has overloaded. After removing the imaging unit, rotate the OPC coupler. (Spec : 6 kgf.cm) If there is any damage, the OPC coupler can’t rotate well. Replace the imaging unit. 4) The main BLDC motor is defective. • Unplug the connector from the motor carefully. • Replace the main BLDC motor with new one. 5) If the problem persists, replace the main board. |
| Error code: | A1-2110 |
| Display: | Actuator Motor Failure #A1-2110. |
| Description: | OPC BLDC motor does not work normally. |
| Remedy: | 1) Turn off the machine then on. 2) If the problem persists, replace the imaging unit. 3) If the problem persists, replace the Main drive unit. |
| Error code: | A3-3312 |
| Display: | Error #A3-3312 Call for service |
| Description: | Error: #A3-3312 Turn off then on |
| Causes: | The outer temperature sensor is defective. |
| Remedy: | 1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Remove the front cover. 3) Replace the PBA-DEVE CRUM JOINT. |
| Error code: | C1-1110 |
| Display: | Prepare new yellow toner cartridge. |
| Description: | Toner remained is 5 - 30% of its life. |
| Causes: | Toner cartridge is almost empty. |
| Remedy: | 1) Open the front cover. 2) Remove the toner cartridge(MLT-D709S). (Toner cartridge with level of “Low” will be exhausted soon.) |
| Error code: | C1-1120, C1-1140 |
| Display: | Replace with new toner cartridge. End of life, Replace with new toner cartridge. |
| Description: | The remaining toner in cartridge is empty. |
| Remedy: | Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one. |
| Error code: | C1-1311 |
| Display: | Imaging Unit Failure: #C3-1312. Install imaging unit again |
| Description: | Toner supply is inefficient or abnormal. |
| Remedy: | 1) Turn the machine off. Open the front cover 2) Remove the toner cartridge. Shake the toner cartridge horizontally to distribute the toner evenly inside the cartridge. 3) If the problem persists, check the follows. a) Check if the Toner Supply Drive Unit(JC93-00436A) is defective. b) Check if the Toner Duct Drive Unit(JC93-00451A) is defective. 4) If the problem persists, replace the Toner cartridge(MLT-D709S). |
| Error code: | C1-1411 |
| Display: | Toner cartridge is not installed. Install it. |
| Description: | Toner cartridge is not installed. Install the cartridge |
| Causes: | The toner cartridge is not installed. / The machine can’t detect the toner cartridge. |
| Remedy: | 1) Turn the machine off then on. 2) Remove the toner cartridge. Thoroughly roll the cartridge five or six times to distribute the toner evenly inside the cartridge. And reinstall the toner cartridge. 3) Check if the CRUM contact area is contaminated. Clean it. |
| Error code: | C1-1512 |
| Display: | Toner cartridge is not compatible. Check users guide. |
| Description: | Toner cartridge is not compatible. Check users guide. |
| Causes: | Toner cartridge is not compatible. |
| Remedy: | 1) Print the supply information report. Check information of the toner cartridge. 2) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one. |
| Error code: | C3-1110, C3-1120, C3-1140 |
| Display: | Prepare new imaging unit Replace with new imaging unit Replace with new imaging unit |
| Description: | The remaining life of the imaging unit is less than 10% of its life. The remaining life of the imaging unit is less than 0% of its life. |
| Remedy: | Prepare the new imaging unit. |
| Error code: | C3-1312 |
| Display: | Imaging Unit Failure: #C3-1312. Install imaging unit again. |
| Description: | Imaging Unit Failure: #C3-1312. Install imaging unit again |
| Causes: | Toner supply is inefficient or abnormal. |
| Remedy: | 1) Turn the machine off. Open the front cover 2) Remove the toner cartridge. Shake the toner cartridge horizontally to distribute the toner evenly inside the cartridge. 3) If the problem persists, check the follows. a) Check if the Toner Supply Drive Unit(JC93–00436A) is defective. b) Check if the Toner Duct Drive Unit(JC93–00451A) is defective. 4) If the problem persists, replace the toner cartridge. 5) If the problem persists, replace the drum unit. |
| Error code: | C3-1330 |
| Display: | Imaging Unit Failure: #C3-1330. Install imaging unit again. |
| Description: | The imaging unit is not installed properly. |
| Remedy: | 1) Open the front cover. 2) If the imaging unit is not installed, install it. Try to test the machine again. 3) If the imaging unit is installed, remove it. Check if the modular jack is contaminated or broken. 4) Clean the modular jack or replace the imaging unit. 5) If it is OK, check the CN22 harness connection on the main board. 6) If the harness is defective, replace it. 7) Turn the machine off then on. Try to test the machine. |
| Error code: | C3-1512 |
| Display: | Imaging unit is not compatible. Check user`s guide |
| Description: | Imaging unit is not compatible. Check the user guide |
| Causes: | Imaging unit is not compatible. |
| Remedy: | 1) Open the front cover. Remove the imaging unit. 2) Check if the label information of the imaging unit is same with the machine’s one. (ex. /SEE) 3) If label information is different from the machine or the imaging unit is not a samsung genuine, replace it with a new one. |
| Error code: | H1-1210, H1-1310 |
| Display: | Paper Jam in Tray2 Paper Jam in Tray3 Paper Jam in Tray4 Paper Jam in Tray5 |
| Description: | A jammed paper has occurred in the option cassette. (SCF unit) |
| Remedy: | 1. Remove the jammed paper. If the problem persists, check the followings. 2. Check if the paper is loaded in the SCF tray properly. 3. Check if the roller is defective or worn out. 4. Check if the Empty/ Pick up/ Regi-Act sensor is working properly. 5. Check if the main board/ motor/ clutch connector are connected properly. 6. Check if the AS-SPRING_ES is deforemd or assembled properly. 7. Check if the Press D-cut of the Gear-Lifting is broken. 8. If the problem persists after checking No. 1-7, replace the SCF main board. 9. If the probelm persists, replace the Drop connector harness. |
| Error code: | H1-1222, H1-1322 |
| Display: | Tray2 cassette is pulled out. Insert it properly. Tray3 cassette is pulled out. Insert it properly. Tray4 cassette is pulled out. Insert it properly. Tray5 cassette is pulled out. Insert it properly. |
| Description: | A optional cassette (SCF) is pulled out. |
| Remedy: | 1. Check if the optional cassette is inserted propelry. Remove the cassette then re-install it. 2. Check if the Signal-Switch is deformed or broken. If it is defective, replace it. |
| Error code: | H1-1230, H1-1240, H1-1330 |
| Display: | Input System Failure: #. Check Tray # connection. Tray # is not installed. Install the tray. |
| Description: | The communication error between the machine and option cassette has occurred. |
| Remedy: | 1) Turn the machine off then on. 2) Check if the option tray harness on main board is connected properly. Reconnect or replace the harness. 3) Check if the SCF draw connector is broken. 4) If the problem persists, replace the SCF main board. |
| Error code: | H1-1252, H1-1352 |
| Display: | Paper Empty in Tray# |
| Description: | Paper in the optional cassette is empty. |
| Remedy: | 1. Check if the paper in optional cassette is loaded. Load the paper. 2. Check if the empty actuator and empty senosr are assembled properly. 3. If the empty actuator is defective, replace it. 4. If the problem persists after replacing the empty actuator, replace the empty sensor. |
| Error code: | H1-1253, H1-1353 |
| Display: | Error : # |
| Description: | The paper in the optional cassette is not picked up. |
| Remedy: | 1. Check if the Gear-Idle Lift is broken. 2. Check if the Signal-Swtich is operated properly. If it is defective, replace it. 3. Check if the Lift-Motor connector is connected properly. 4. Check if the Press D-Cut of the Gear-Lifting is deformed or broken. 5. If the problem persists, replace the Lift-Motor. |
| Error code: | H1-1340, H1-1430, H1-1440 |
| Display: | Input System Failure: #. Check Tray # connection. Tray # is not installed. Install the tray. |
| Description: | The communication error between the machine and option cassette has occurred. |
| Remedy: | 1) Turn the machine off then on. 2) Check if the option tray harness on main board is connected properly. Reconnect or replace the harness. 3) Check if the SCF draw connector is broken. 4) If the problem persists, replace the SCF main board. |
| Error code: | H1-1410, H1-1510 |
| Display: | Paper Jam in Tray2 Paper Jam in Tray3 Paper Jam in Tray4 Paper Jam in Tray5 |
| Description: | A jammed paper has occurred in the option cassette. (SCF unit) |
| Remedy: | 1. Remove the jammed paper. If the problem persists, check the followings. 2. Check if the paper is loaded in the SCF tray properly. 3. Check if the roller is defective or worn out. 4. Check if the Empty/ Pick up/ Regi-Act sensor is working properly. 5. Check if the main board/ motor/ clutch connector are connected properly. 6. Check if the AS-SPRING_ES is deforemd or assembled properly. 7. Check if the Press D-cut of the Gear-Lifting is broken. 8. If the problem persists after checking No. 1-7, replace the SCF main board. 9. If the probelm persists, replace the Drop connector harness. |
| Error code: | H1-1422, H1-1522 |
| Display: | Tray2 cassette is pulled out. Insert it properly. Tray3 cassette is pulled out. Insert it properly. Tray4 cassette is pulled out. Insert it properly. Tray5 cassette is pulled out. Insert it properly. |
| Description: | A optional cassette (SCF) is pulled out. |
| Remedy: | 1. Check if the optional cassette is inserted propelry. Remove the cassette then re-install it. 2. Check if the Signal-Switch is deformed or broken. If it is defective, replace it. |
| Error code: | H1-1452, H1-1552 |
| Display: | Paper Empty in Tray# |
| Description: | Paper in the optional cassette is empty. |
| Remedy: | 1. Check if the paper in optional cassette is loaded. Load the paper. 2. Check if the empty actuator and empty senosr are assembled properly. 3. If the empty actuator is defective, replace it. 4. If the problem persists after replacing the empty actuator, replace the empty sensor. |
| Error code: | H1-1453, H1-1553 |
| Display: | Error : # |
| Description: | The paper in the optional cassette is not picked up. |
| Remedy: | 1. Check if the Gear-Idle Lift is broken. 2. Check if the Signal-Swtich is operated properly. If it is defective, replace it. 3. Check if the Lift-Motor connector is connected properly. 4. Check if the Press D-Cut of the Gear-Lifting is deformed or broken. 5. If the problem persists, replace the Lift-Motor. |
| Error code: | H1-1530, H1-1540 |
| Display: | Input System Failure: #. Check Tray # connection. Tray # is not installed. Install the tray. |
| Description: | The communication error between the machine and option cassette has occurred. |
| Remedy: | 1) Turn the machine off then on. 2) Check if the option tray harness on main board is connected properly. Reconnect or replace the harness. 3) Check if the SCF draw connector is broken. 4) If the problem persists, replace the SCF main board. |
| Error code: | H2-1100 |
| Display: | Paper jam inside of finisher. Remove paper |
| Description: | Finisher Entrance sensor actuator does not return after a paper covers it IOT Exit Roller grabs the paper. Or Finisher Feeding Motors Stopped. Or Finisher Entrance Sensor damaged or harness damaged. Or Finisher Main Board damaged |
| Remedy: | 1. Check Jam Occurrence in IOT. - If the IOT roller is grabbing the paper, it’s IOT fault 2. Check the Main Board Harness Connection. 3. Check Finisher Entrance operation & harness connection. 4. Check Finisher Feeding Entrance Motor Harness Connection and operation. 5. Check Finisher Feeding Exit Motor Harness Connection and operation. 6. If the same problem happens after checking 1-5, Replace the Finisher main board. 7. If the same problem happens after checking 5, replace the Finisher harnesses. |
| Error code: | H2-1101 |
| Display: | Paper jam in front of finisher. Remove paper |
| Description: | Paper doesn’t reach Finisher’s Entrance Sensor. Paper jam in IOT. Or Finisher Diverter operation not well. Or IOT Defl ector Damaged. Or Finisher Entrance Sensor not working (Finisher Entrance Sensor Damaged, Harness connection not well, Main Board damaged) |
| Remedy: | 1. Check Jam Occurrence in IOT. 2. Check IOT Defl ector part’s operation. 3. Check the Main Board Harness Connection. 4. Check Finisher’s Entrance operation & harness connection 5. Referring to H2-1800, Check the Finisher Diverter operation. 6. If the same problem happens after checking 1-5, Replace the Finisher main board. 7. If the same problem happens after checking 6, replace the Finisher harnesses. |
| Error code: | H2-1102 |
| Display: | Paper jam inside of finisher. Remove paper |
| Description: | Initialization started with Jammed paper covering Finisher Entrance Sensor. Paper exists covering Finisher Entrance Sensor. Or Finisher Entrance Sensor Damaged or harness connection not well. Or Finisher Main Board damaged |
| Remedy: | 1. Check if there is a jammed paper inside Finisher. 2. Check the Main Board Harness Connection. 3. Check Finisher Entrance operation & harness connection. 4. If the same problem happens after checking 1-3, Replace the Finisher main board. 5. If the same problem happens after checking 4, replace the Finisher harnesses. |
| Error code: | H2-1200, H2-1300 |
| Display: | Jam inside Finisher Jam exit of Finisher |
| Description: | IOT Exit Roller grabs the paper. Or Finisher Feeding Motors Stopped. Or Finisher Exit Sensor damaged or harness damaged. Or Finisher Main Board damaged |
| Remedy: | 1) Check Jam Occurrence in IOT. If the IOT roller is grabbing the paper, it’s IOT fault. 2) Check the Main Board Harness connection. 3) Check Finisher Exit Sensor operation & harness connection. 4) Check Finisher Feeding Entrance Motor harness connection and operation. 5) Check Finisher Feeding Exit Motor Harness connection and operation. 6) If the same problem happens after checking 1-5, Replace the Finisher main board. 7) If the same problem happens after checking 6, replace the Finisher harnesses. |
| Error code: | H2-1302 |
| Display: | Paper jam inside of finisher. Remove paper |
| Description: | Initialization started with Jammed paper covering Finisher Exit Sensor. Paper exists covering Finisher Exit Sensor. Or Finisher Exit Sensor Damaged or harness connection not well. Or Finisher Main Board damaged |
| Remedy: | 1. Check if there is a jammed paper on the feeding path of Finisher. 2. Check the Main Board Harness Connection. 3. Check Finisher Exit sensors’ operation & harness connection. 4. If the same problem happens after checking 1-3, Replace the Finisher main board. 5. If the same problem happens after checking 4, replace the Finisher harnesses. |
| Error code: | H2-1710, H2-1711 |
| Display: | Finisher Failure: #H2-1710. Check fi nisher Finisher Failure: #H2-1711. Check fi nisher |
| Description: | Front Jogger is not working well. Front Jogger Home Sensor, Front Jogger Motor Harness Connection not well or damaged, Main Board damaged. |
| Remedy: | 1. Check the Main Board Harness Connection. 2. Check the Finisher Front Jogger Home Sensor’s Harness Connection. 3. Check the Finisher Front Jogger Motor’s Harness Connection and operation. 4. Check if Front jogger part is contaminated. 5. If the same problem happens after checking 1-4, Replace the Finisher main board. 6. If the same problem happens after checking 5, Replace the Finisher harnesses. |
| Error code: | H2-1720, H2-1721 |
| Display: | Finisher Failure: #H2-1720. Check fi nisher Finisher Failure: #H2-1721. Check fi nisher |
| Description: | Rear Jogger is not working well. Rear Jogger Home Sensor, Rear Jogger Motor Harness Connection not well or damaged, Main Board damaged. |
| Remedy: | 1. Check the Main Board Harness Connection. 2. Check the Finisher Rear Jogger Home Sensor’s Harness Connection. 3. Check the Finisher Rear Jogger Motor’s Harness Connection and operation. 4. Check if Rear jogger part is contaminated. 5. If the same problem happens after checking 1-4, Replace the Finisher main board. 6. If the same problem happens after checking 5, Replace the Finisher harnesses. |
| Error code: | H2-1730, H2-1731 |
| Display: | Finisher Failure: #H2-1730. Check fi nisher Finisher Failure: #H2-1731. Check fi nisher |
| Description: | Support Finger (Extension Tray) is not working well. Support Finger Home Sensor, Support Finger Motor Harness Connection not well or damaged, Main Board damaged |
| Remedy: | 1. Check the Main Board Harness Connection. 2. Check the Finisher Support Finger Home Sensor’s Harness Connection. 3. Check the Finisher Support Finger Motor’s Harness Connection and operation. 4. If the same problem happens after checking 1-3, Replace the Finisher main board. 5. If the same problem happens after checking 4, Replace the Finisher harnesses. |
| Error code: | H2-1750, H2-1751 |
| Display: | Error: # / Finisher Failure: #. Check finisher |
| Description: | Stapler harness connection loose. Or Cartridge set sensors are damaged, Or Main Board is damaged. |
| Remedy: | NOTE Make sure that the staple strips on top of the stack are complete and flat. Remove any partial strips and any strips that are bent. 1) Check the Main Board Harness Connection. 2) Check the Stapler harness connections. 3) Check if staples are stuck in Stapler Head area and damage of Stapler itself. 4) If the same problem happens after checking 1-3, Replace the Finisher main board. 5) If the same problem happens after checking 4, Replace the Finisher Stapler. 6) If the same problem happens after checking 5, Replace the Finisher harnesses. |
| Error code: | H2-1752 |
| Display: | Finisher Failure: #H2-1752. Check finisher |
| Description: | Finisher compiles all the papers and moves them to stapling position and do nothing. the message “Stapler Safety Fault” pops up. Safety Switch Harness connection not well. Main Board damaged. |
| Remedy: | 1. Check the Main Board Harness Connection. 2. Check the Safety Switch Harness Connection. 3. Check the Safety Unit’s operation. Check the switch is clicked when the Safety Link moves. 4. Check the Safety Unit’s operation using Rear Jogger. The same “switch ON/OFF” operation should be followed. 5. Check the Safety Unit’s operation. When Rear Jogger stands at the position having the Shield and Rear Jogger met, the Safety Switch should be ON. 6. If the same problem happens after checking 1-5, Replace the Finisher main board. 7. If the same problem happens after checking 6, Replace the Finisher harnesses. |
| Error code: | H2-1753, H2-1A70 |
| Display: | Error: # / Finisher Failure: #. Check finisher |
| Description: | Stapler harness connection loose. Or Cartridge set sensors are damaged, Or Main Board is damaged. |
| Remedy: | NOTE Make sure that the staple strips on top of the stack are complete and flat. Remove any partial strips and any strips that are bent. 1) Check the Main Board Harness Connection. 2) Check the Stapler harness connections. 3) Check if staples are stuck in Stapler Head area and damage of Stapler itself. 4) If the same problem happens after checking 1-3, Replace the Finisher main board. 5) If the same problem happens after checking 4, Replace the Finisher Stapler. 6) If the same problem happens after checking 5, Replace the Finisher harnesses. |
| Error code: | H2-1760, H2-1A80 |
| Display: | Finisher Failure: #H2-1760. Check fi nisher Finisher Failure: #H2-1A80. Check fi nisher |
| Description: | Stacker Unit is not working. Stacker Level sensor, Stack Full sensor, Stacker Motor Harness Connection not well or damaged, Main Board damaged. |
| Remedy: | 1. Check the Main Board Harness Connection. 2. Check the Stacker Level Sensor’s Harness Connection and Actuator’s operation & its Spring behind the wall. 3. Check the Stacker Motor Harness Connection and operation. 4. Check the Stack Full Sensor Connection and operation. 5. If the same problem happens after checking 1-3, Replace the Finisher main board. 6. If the same problem happens after checking 4, replace the Finisher harnesses. |
| Error code: | H2-1800 |
| Display: | Finisher Failure: #H2-1800. Check fi nisher sens |
| Description: | Diverter is not working. Diverter Motor, Sensor Harness Connection not well or damaged. Main Board Damaged. IOT’s Defl ector damaged. |
| Remedy: | 1. Check the Main Board Harness Connection. 2. Check the IOT’s Defl ector operation. 3. Check Diverter sensor harness connection. 4. Diverter Motor Harness Connection and operation. 5. Check if Diverter Unit is not contaminated. 6. If the same problem happens after checking 1-5, Replace the Finisher main board. 7. If the same problem happens after checking 6, replace the Finisher harnesses. |
| Error code: | H2-1A20 |
| Display: | Finisher door is open. Close it |
| Description: | Finisher Motors doesn’t work. Jam Cover Opened, Jam Cover not assembled well or Jam Cover Flag damaged, Stapler Door Opened, Stapler Door Micro Switch not assembled well or Stapler Door Flag damaged, Harness Damaged. Main Board Damaged, door fl ag damaged. |
| Remedy: | 1. Check the Jam Cover and Stapler Door Closed fi rmly. 2. Check if Mounting Part not damaged - Male part in Finisher - Female part in IOT 3. Check the Main Board Harness Connection. 4. Check the Stapler Door Switch Harness Connection. 5. Check the Stapler Door fl ag damaged. 6. Check the Jam Cover Sensor Harness connection. 7. Check the Jam Cover fl ag damaged 8. If the same problem happens after checking 1-7, Replace the Finisher main board. 9. If the same problem happens after checking 8, replace the Finisher harnesses. |
| Error code: | H2-1A32 |
| Display: | Too much paper in finisher stacker. Remove printed paper |
| Description: | Finisher Full message pops when papers on the Stacker Tray are stacked fully or the full sensor detecting mechanism is out of order Finisher Full detecting sensor damaged, harness connection not well or damaged, Main Board damaged. |
| Remedy: | 1. Check the Stacker Tray’s Full Sensor Connection and check if Flag is damaged - The sensor must not be covered besides the full detecting fl ag. 2. Check Finisher Main Board Harness Connection. 3. If the same problem happens after checking 1-2, Replace the Finisher main board. 4. If the same problem happens after checking 3, Replace the Finisher harnesses. |
| Error code: | H2-1A50 |
| Display: | Finisher Failure: #H2-1A50. Check finisher |
| Description: | Finisher doesn’t work because of Communication error between finisher and IOT. Interface Cable Connection not well or Interface Cable(Harness) damaged, Main Board damaged. |
| Remedy: | 1. Check if Mounting Part not damaged - Male part in Finisher - Female part in IOT 2. Check the Main Board Harness Connection. 3. If the same problem happens after checking 1-2, Replace the Finisher main board.. 4. If the same problem happens after checking 3, Replace the Finisher harnesses |
| Error code: | H2-1A62, H2-1A63 |
| Display: | Staple Low / Staple cartridge is low. Replace it Staple Empty / Staple cartridge is empty. Replace it |
| Description: | The front cover or the top cover is not securely latched or the transfer belt is not installed. |
| Remedy: | 1) Check if the cartridge exists. 2) Check if the cartridge is inserted firmly. 3) Check if staples in cartridge are in some level. - With such level like the below picture or lower during POPO (Power off power on), The sensor detects it empty. NOTE Make sure that the staple strips on top of the stack are complete and flat. Remove any partial strips and any strips that are bent. 4) Check the Stapler harness connection. 5) Check the Cartridge Set sensors’ operation. 6) Check the Main Board Harness Connection. 7) If the same problem happens after checking 1-6, replace the Finisher main board. 8) If the same problem happens after checking 7, replace the Finisher Stapler. 9) If the same problem happens after checking 8, replace the Finisher harnesses. |
| Error code: | H2-4100 |
| Display: | Paper jam in front of mailbox. Remove paper. |
| Description: | Paper doesn’t reach Mailbox’s Entrance Sensor. Paper jam in IOT. Or Mailbox Lower Diverter operation not well. Or IOT Defl ector Damaged. Or Mailbox Entrance Sensor not working (Mailbox Entrance Sensor Damaged, Harness connection not well, MainBoard damaged) |
| Remedy: | 1. Check Jam Occurrence in IOT. 2. Check IOT Defl ector part’s operation. 3. Check Mailbox Main Board Harness connection. 4. Check Mailbox Entrance operation & harness connection. 5. Refer to the Lower Diverter fault. 6. If the same problem happens after checking 1-5, Replace the mailbox main board. 7. If the same problem happens after checking 6, Replace the mailbox harnesses. |
| Error code: | H2-4101, H2-4102 |
| Display: | Jam inside mailbox |
| Description: | IOT Exit Roller grabs the paper. Paper exists covering Mailbox Entrance Sensor. Or Mailbox Feeding Motor Stops. Or Mailbox Entrance Sensor damaged or harness damaged. Or Mailbox Main Board damaged. |
| Remedy: | 1) Check Jam Occurrence in IOT. If the IOT roller is grabbing the paper, it’s IOT fault. 2) Check Mailbox Main Board Harness connection. 3) Check Mailbox Entrance operation & harness connection. 4) Check Mailbox Feeding Motor Harness connection and operation. 5) If the same problem happens after checking 1-4, replace the mailbox main board. 6) If the same problem happens after checking 5, replace the mailbox harnesses. |
| Error code: | H2-4200, H2-4201, H2-4300 |
| Display: | Jam front of bin # Jam at mailbox bin # |
| Description: | IOT Exit Roller grabs the paper. Or Mailbox Feeding Motor Stops. Or Mailbox Entrance Exit Sensor damaged or Mailbox Gate doesn’t work or harness damaged. Or Mailbox Main Board damaged. |
| Remedy: | 1) Check Jam Occurrence in IOT. - If the IOT roller is grabbing the paper, it’s IOT fault. 2) Check Mailbox Main Board Harness connection. 3) Check Mailbox Exit-related Sensors operation & harness connection. 4) Check Mailbox Feeding Motor Harness Connection and operation. 5) Referring to Upper Diverter Fault, check the Upper Diverter’s operation. 6) Referring to Lower Diverter Fault, check the Lower Diverter’s operation 7) If the same problem happens after checking 1-6, replace the mailbox main board. 8) If the same problem happens after checking 7, replace the mailbox harnesses. |
| Error code: | H2-4202, H2-4302 |
| Display: | Jam at mailbox bin # |
| Description: | Paper exists covering Mailbox Exit Sensor. Or Mailbox Exit Sensor is damaged or harness connection loose. Or Mailbox Main board is damaged. |
| Remedy: | 1) Check if there is a jammed paper on the feeding path of Mailbox. 2) Check Mailbox Main Board Harness connection. 3) Check Mailbox Bin1 Exit-related sensors’ operation & harness connection. 4) If the same problem happens after checking 1-3, replace the mailbox main board. 5) If the same problem happens after checking 4, replace the mailbox harnesses. |
| Error code: | H2-4301, H2-4400, H2-4401 |
| Display: | Jam front of bin # Jam at mailbox bin # |
| Description: | IOT Exit Roller grabs the paper. Or Mailbox Feeding Motor Stops. Or Mailbox Entrance Exit Sensor damaged or Mailbox Gate doesn’t work or harness damaged. Or Mailbox Main Board damaged. |
| Remedy: | 1) Check Jam Occurrence in IOT. - If the IOT roller is grabbing the paper, it’s IOT fault. 2) Check Mailbox Main Board Harness connection. 3) Check Mailbox Exit-related Sensors operation & harness connection. 4) Check Mailbox Feeding Motor Harness Connection and operation. 5) Referring to Upper Diverter Fault, check the Upper Diverter’s operation. 6) Referring to Lower Diverter Fault, check the Lower Diverter’s operation 7) If the same problem happens after checking 1-6, replace the mailbox main board. 8) If the same problem happens after checking 7, replace the mailbox harnesses. |
| Error code: | H2-4402, H2-4502 |
| Display: | Jam at mailbox bin # |
| Description: | Paper exists covering Mailbox Exit Sensor. Or Mailbox Exit Sensor is damaged or harness connection loose. Or Mailbox Main board is damaged. |
| Remedy: | 1) Check if there is a jammed paper on the feeding path of Mailbox. 2) Check Mailbox Main Board Harness connection. 3) Check Mailbox Bin1 Exit-related sensors’ operation & harness connection. 4) If the same problem happens after checking 1-3, replace the mailbox main board. 5) If the same problem happens after checking 4, replace the mailbox harnesses. |
| Error code: | H2-4500, H2-4501 |
| Display: | Jam front of bin # Jam at mailbox bin # |
| Description: | IOT Exit Roller grabs the paper. Or Mailbox Feeding Motor Stops. Or Mailbox Entrance Exit Sensor damaged or Mailbox Gate doesn’t work or harness damaged. Or Mailbox Main Board damaged. |
| Remedy: | 1) Check Jam Occurrence in IOT. - If the IOT roller is grabbing the paper, it’s IOT fault. 2) Check Mailbox Main Board Harness connection. 3) Check Mailbox Exit-related Sensors operation & harness connection. 4) Check Mailbox Feeding Motor Harness Connection and operation. 5) Referring to Upper Diverter Fault, check the Upper Diverter’s operation. 6) Referring to Lower Diverter Fault, check the Lower Diverter’s operation 7) If the same problem happens after checking 1-6, replace the mailbox main board. 8) If the same problem happens after checking 7, replace the mailbox harnesses. |
| Error code: | H2-4700, H2-4701 |
| Display: | Mailbox Failure: #H2-4700. Check mailbox. Mailbox Failure: #H2-4701. Check mailbox |
| Description: | Two Upper Gates seen when opening Rear Door is not operating well. Upper Diverter Motor or Upper Diverter Sensor not assembled well or damaged. Harness Damaged. Main Board damaged. |
| Remedy: | 1. Check Upper Diverter Motor Harness connection. 2. Check Upper Diverter Sensor Harness connection. 3. Check Mailbox Main Board Harness connection. 4. Check Upper Diverter operation. 5. Check Mailbox Gate operation. 6. If the same problem happens after checking 1-5, replace the mailbox main board. 7. If the same problem happens after checking 6, replace the mailbox harnesses. |
| Error code: | H2-4710, H2-4711 |
| Display: | Mailbox Failure: #H2-4710. Check mailbox. Mailbox Failure: #H2-4711. Check mailbox |
| Description: | The Lowest Gate seen when opening Rear Door is not operating well. Lower Diverter Motor or Lower Diverter Sensor not assembled well or damaged. Harness Damaged. Main Board damaged. |
| Remedy: | 1. Check Lower Diverter Motor Harness connection. 2. Check Lower Diverter Sensor Harness connection. 3. Check Mailbox Main Board Harness connection. 4. Check Lower Diverter operation. 5. Check Mailbox Gate operation. 6. If the same problem happens after checking 1-5, replace the mailbox main board. 7. If the same problem happens after checking 6, replace the mailbox harnesses. |
| Error code: | H2-4A20 |
| Display: | Mailbox door is open. Close it |
| Description: | Mailbox Motors doesn’t work. Rear Door Opened, Micro Switch not assembled well or damaged, Harness Damaged. Main Board Damaged, door fl ag damaged. |
| Remedy: | 1. Check the Rear Door Closed fi rmly. 2. Check Mailbox Main Board Harness connection. 3. Check the Rear Door Switch Harness connection. 4. Check the Mailbox cover fl ag damaged. 5. If the same problem happens after checking 1-4, replace the mailbox main board. 6. If the same problem happens after checking 5, replace the mailbox harnesses. |
| Error code: | H2-4A32, H2-4A35 |
| Display: | Mailbox bin # full / Too much paper in bin #. Remove printed paper |
| Description: | Mailbox Full detecting sensor damaged, harness connection loose or damaged, Main Board is damaged. |
| Remedy: | 1) Check the Bin’s Full Sensor Connection and Actuator’s operation. 2) Check Main Board Harness connection. 3) If the same problem happens after checking 1-2, replace the mailbox main board. 4) If the same problem happens after checking 3, replace the mailbox harnesses. |
| Error code: | H2-4A38, H2-4A3C |
| Display: | Mailbox bin # full / Too much paper in bin #. Remove printed paper |
| Description: | Mailbox Full detecting sensor damaged, harness connection loose or damaged, Main Board is damaged. |
| Remedy: | 1) Check the Bin’s Full Sensor Connection and Actuator’s operation. 2) Check Main Board Harness connection. 3) If the same problem happens after checking 1-2, replace the mailbox main board. 4) If the same problem happens after checking 3, replace the mailbox harnesses. |
| Error code: | H2-4A50 |
| Display: | Error: #H2-4A50 / Mainbox Failure: #H2-4A50. Check mailbox |
| Description: | A communication problem has occurred at mailbox. |
| Remedy: | 1) Check the connection between machine and mailbox. |
| Error code: | M1-1110 |
| Display: | Paper Jam in Tray1. |
| Description: | Paper jam in tray 1. Please remove the paper |
| Causes: | The jammed paper has occurred in the tray. |
| Remedy: | 1) Clear the jam from the tray1. 2) Remove the tray. Check if the loaded paper is in proper place. Align it. 3) If the jammed paper occurred before entering it to the separation roller, check the Sheet Retard / Pickup roller / Forward roller / CST Knock up / CST Knock up Spring. 4) If the jammed paper occurred after entering it to the separation roller, check the Ribs in paper path. |
| Error code: | M1-3122 |
| Display: | Tray 1 cassette is pulled out. Insert it properly. |
| Description: | Tray 1 cassette is pulled out. Insert it properly. |
| Causes: | Tray 1 is pulled out or the auto size sensor connector is not connected or broken. |
| Remedy: | 1) Remove and insert Tray1 correctly. 2) If Tray1 is not locked or pulled out without holding the locking lever, remove Tray1. 3) Check if foreign substance or paper is inside the space between Tray1,2. If so, please remove it. 4) If the problem persists, check that the auto size sensor is connected properly. 5) If the problem persists, replace the main board(JC92–02452A). |
| Error code: | M1-4111 |
| Display: | Input System Failure #M1-4111 : Pull Tray 1 out and insert it. |
| Description: | Input System Failure #M1–4111 : Pull Tray 1 out and insert it. |
| Causes: | The paper is not fed from tray1. |
| Remedy: | 1) Remove tray1 and re-install it. 2) If the problem persists, turn the machine off then on. 3) Enter SVC mode. Execute pickup motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100-0370) 4) If the pick up motor operation is abnormal, turn the machine off. 5) Remove the rear cover. 6) Check if the connection between pickup drive unit1 and main board is secure. 7) If the connection is OK, replace the pickup drive unit(JC93-00442A). 8) If the problem persists, check the pickup unit1. a) Check if the photo sensor in the pickup unit1 is defective. b) If the sensor(0604–001393) is defective, replace it. |
| Error code: | M1-5112 |
| Display: | Paper is empty in tray 1. |
| Description: | Paper is empty in tray 1. Load paper. |
| Causes: | Paper is empty in Tray1 |
| Remedy: | 1) Take off the cassette. If there is no paper on the tray, load the paper. 2) If the problem persists, check the following. a) Check if the paper empty sensor is contaminated or defective. Replace it. |
| Error code: | M1-5612 |
| Display: | Paper is empty in MP Tray. Load paper. |
| Description: | Paper is empty in MP Tray. Load paper. |
| Causes: | Paper in the MP tray is less than 10%. / The photo sensor is defective. |
| Remedy: | 1) Load the paper in the MP tray. 2) If paper is loaded but error message has not disappeared, check the following : a) If the photo sensor is contaminated, clean it. b) If the photo sensor is defective, replace it(0604–001393). c) If the actuator is defective, replace it(JC66-03217A). |
| Error code: | M2-1110 |
| Display: | Paper Jam inside machine. |
| Description: | Paper jam inside of machine. Please remove the paper |
| Causes: | A paper jam was detected at the feed sensor. |
| Remedy: | 1) Remove the jammed paper. If the error persists, check the followings. 2) Check if the feed/regi sensor connector is connected properly. Reconnect the harness. 3) Check if the regi./feed actuator works normally. If it is defective or broken, replace it. 4) If the photo sensor is defective, replace the regi/feed sensor PBA. |
| Error code: | M2-2210 |
| Display: | Jam inside of duplex |
| Description: | A paper jam was detected in the bottom of duplex. |
| Remedy: | 1) Remove the jammed paper. 2) Remove the contamination or obstacles in the paper path. 3) If this jam error occur continually, replace the duplex unit. |
| Error code: | M2-2310 |
| Display: | Paper Jam bottom of duplex. |
| Description: | A paper jam was detected in the bottom of duplex. 1. There is some obstacles in the paper path. 2. The paper guide in the tray was not adjusted properly. 3. The exit sensor was not assembled properly. |
| Remedy: | 1. Remove the jammed paper. 2. Remove the contamination or obstacles in the paper path. 3. Adjust the paper guide properly. 4. Check if the exit sensor is assembled properly. Reassemble it. |
| Error code: | M3-1110 |
| Display: | Paper jam in exit area. |
| Description: | A paper jam was detected in the exit area. |
| Causes: | A paper jam was detected in the exit area. |
| Remedy: | 1) Open the rear cover. Remove the jammed paper. 2) Check if the Guide-Change Duplex of the rear cover is defective. 3) Check if the exit sensor and actuator is working normally. |
| Error code: | M3-2130 |
| Display: | Output bin full Remove paper |
| Description: | Paper in output bin is full. Remove printed paper |
| Causes: | The machine detected that the output tray has got full or the bin-full sensor is defective. |
| Remedy: | 1) Remove the paper on the output tray. (The maximum loading capacity is 150 sheets based on standard paper (80 g/m²).) 2) Check if the Bin-full Sensor connector is connected properly. Reconnect it or replace the Bin-full sensor. |
| Error code: | S2-4210 |
| Display: | Front door is open. Close it. |
| Description: | Front door is open. Close it. |
| Causes: | Front cover or Side cover is opened. |
| Remedy: | 1) Close the front cover correctly. 2) Check if the cover open sensor connector is connected properly. Reconnect it. 3) If the sensor is defective, replace it. |
| Error code: | S2-4610 |
| Display: | Rear Door is open. Close it |
| Description: | The rear cover is closed but error message is not disappeared. 1. The rear cover is closed perfectly. 2. Relay connector pin is defective. 3. Harness connection error. |
| Remedy: | 1. Check if the rear cover is closed perfectly. 2. Check the Relay connector Pin If it is defective, replace it. 3. Check the Relay connector if it is defective, replace it. 4. Remove the left cover. Check the harness.. between the Joint board and Relay connector. 5. Check if the harness is connected to the connector properly. |
| Error code: | S6-3123 |
| Display: | This IP address conflicts with that of other system. Check it. |
| Description: | This IP address conflicts with that of other system. Check it. |
| Causes: | Network has some problem. (IP address conflicts with that of other system. / Communication error / There is no response when checking the ping test.) |
| Remedy: | Change the machine’s IP address. • Execute the Samsung Easy Printer Manager program. (Device setting > Network > IP address). Change the IP address. • In case of DHCP or Bootp, reboot the machine to receive a new IP address. |
| Error code: | S6-3128 |
| Display: | 802.1x authentication failed. Please Contact the System Administrator |
| Description: | There is no response when checking the ping test. ID or Password is incorrect. |
| Causes: | Network error. ( A authenticator(eg switch) rejected authentication. / There is no response when checking the ping test.) |
| Remedy: | 1) Change the IP adredd (Machine Setup > Network Setting > Login > TCP/IP > Select the network protocol > IP Setting 2) Inut the Network Login ID and Password correctly. |
| Error code: | U1-2115, U1-2116 |
| Display: | Fuser Unit Failure #U1-2115 : Turn off then on. Fuser Unit Failure #U1-2116 : Turn off then on. |
| Description: | Error #U1-2115 Turn off then on Error #U1-2116 Turn off then on |
| Causes: | The fuser unit has the problem for pressure control. |
| Remedy: | 1) Turn the machine off. Remove and reinstall the fuser unit. Turn the machine off. Is this error message disappeared? 2) Open the rear cover. Check if the fuser pressure cam is working normally. • If the cam operation is normal, replace the cam sensor. 3) Remove the side cover. Check if the fuser motor is working normally. 4) Check if the swing-gear is in the position below when the cam works. If not, replace the fuser drive unit. |
| Error code: | U1-2117 |
| Display: | Fuser Unit Failure: #U1-2117. Turn off then on |
| Description: | Fuser unit Failure: #U1-2117. Turn off then on. |
| Causes: | The machine can’t detect that the fuser unit is installed. |
| Remedy: | 1) After checking the fuser installation, turn the machine off then on. 2) Open the rear cover. Lift up the right side and release the rear cover. 3) If there is no problem, remove 4 screws. 4) Lift up the both levers. Then take off the fuser unit. 5) If there is no problem for above steps, assemble and reinstall fuser unit. Then turn the machine on. 6) If the same error persists, execute the memory clear. 7) If the same error persists, replace the fuser unit with new one. 8) If the same error persists, replace the main board. |
| Error code: | U1-2320, U1-2330 |
| Display: | Error #U1-2320 Turn off then on Error #U1-2330 Turn off then on Error #U1-2332 Turn off then on Error #U1-2340 Turn off then on |
| Description: | The temperature control of fuser unit is abnormal. |
| Remedy: | 1) Check if the input voltage is normal. 2) Turn the machine off. Remove and reinstall the fuser unit. Be careful when connecting the AC-connector and Thermistor connector. 3) Turn the machine on. Is the error message is disappeared? 4) Check the followings. If the fuser unit has any problem, replace it. a) Check if the fuser connector is connected properly. b) Check if the halogen lamp voltage is normal. c) Check if the thermistor is contaminated or twisted. 5) If the problem persists, replace the main board or SMPS board. |
| Error code: | U1-2340 |
| Display: | Error #U1-2340 Turn off then on. |
| Description: | The temperature control of fuser unit is abnormal. |
| Remedy: | 1) Turn the machine off. Re-install the fuser unit. Then turn the machine on. Is the error message is disappeared? 2) If the problem persists, turn the machine off and remove the fuser unit. (Refer to 3.3.13) a) Check if the fuser connector is connected properly. b) Check if the input voltage is normal. c) Check if the thermistor is twisted or contaminated; and is in contact with the Heat Roller. 3) After confirming continuity in the fuser connector and the problem still exists; order an SMPS/HVPS and Fuser Unit and install as is necessary. • HVPS : JC44-00197A • SMPS : JC44-00095D (110V) / JC44-00096D (220V) • Fuser Unit : JC91-01023A (110V) / JC91-01024A (220V) |
| Error code: | U2-1111 |
| Display: | LSU Unit Failure: #U2-1111. Turn off then on |
| Description: | LSU motor does not work normally. 1. Harness connection error. 2. LSU is defective. 3. Main board is defective. |
| Remedy: | Check the followings. 1. Execute the LSU motor test in EDC mode. Check LSU motor operation sound. 2. If there is no sound, remove the right cover. Check if the C9 or C10 connector is connected properly 3. It it is OK, remove the top cover. Check if the LSU connector is connected properly. 4. Check if the LSU harness is defective. 5. Reconnect the LSU harness and then execute the LSU motor test again. 6. Replace the LSU. 7. If the problem persists, replace the main board. |
| Error code: | U2-1113 |
| Display: | Error #U2-1113 Turn off then on. |
| Description: | LSU Motor does not work normally. |
| Causes: | LSU Hsync signal can not be detected correctly. LSU Hsync signal is abnormal. |
| Remedy: | 1) Execute the LSU motor test in EDC mode. Check LSU motor operation sound. 2) If there is no sound, remove the right cover. Check if the LSU harness is connected on the main board properly. (picture-1) 3) If it is OK, remove the top cover. Check if the LSU harness is connected on LSU board properly. (picture- 2,3) 4) Check if the LSU harness is defective. (picture-4) 5) Reconnect the LSU harness and then execute the LSU motor test again. 6) If the problem persists, replace the LSU(JC97-04065A). 7) If the problem persists after replacing LSU, replace the main board. |
