Samsung ML-6050
Рейтинг
Модули
Second Cassette Exploded View
Cover Exploded View
Cassette Exploded View
Motor Exploded View
Frame Exploded View
Second Cassette Frame Exploded View
Pick-Up Exploded View
Main Exploded View
Fuser Exploded View
Детали Motor Exploded View
| Деталь: | MEA RACK-CAST.SCF |
| Парткод: | JC97-01196A |
| Деталь: | GUIDE CST |
| Парткод: | JC72-40306A |
| Деталь: | PMO-GUIDE-2ND CAST. |
| Парткод: | JC72-41227A |
| Деталь: | PLATE-COLOR |
| Парткод: | JC72-41226A |
| Деталь: | SPRING ES |
| Парткод: | 6107-001047A |
| Деталь: | ROLLER EXIT |
| Парткод: | JC72-40361A |
| Деталь: | TAPTITE SCREW |
| Парткод: | 6003-000196 |
| Деталь: | SPRING KNOCKUP |
| Парткод: | JC61-70951A |
| Деталь: | GUIDE SCF |
| Парткод: | JC70-11076A |
| Деталь: | FINGER |
| Парткод: | JC70-10213A |
| Деталь: | PLT KNOCK-UP (12) |
| Парткод: | JC70-11022A |
| Деталь: | MMP, PAD |
| Парткод: | JC73-10911A |
| Деталь: | LABEL(R) PLATE |
| Парткод: | JC68-30929A |
| Деталь: | LOCKER-PLATE |
| Парткод: | JC72-41 21 0A |
| Деталь: | SPRING-LOCKER PLATE |
| Парткод: | JG61-70531A |
| Деталь: | GUIDE PAPER |
| Парткод: | JC70-10219A |
| Деталь: | LABEL(R) HEIGHT |
| Парткод: | JG68-30572A |
| Деталь: | GUIDE-LEGAL |
| Парткод: | JC72-41180A |
| Деталь: | IPR-BRACKET_LEGAL |
| Парткод: | JC70-11086A |
| Деталь: | PMO-GUIDE_LETTER |
| Парткод: | JC72-41392A |
| Деталь: | IPR-BRACKET_LETTER |
| Парткод: | JC70-11087A |
| Деталь: | IPR-TENSION_LETTER |
| Парткод: | JC70-11085A |
| Деталь: | GUIDE-SIDE CASSETTE |
| Парткод: | JC72-41116A |
| Деталь: | GUIDE PLATE |
| Парткод: | JC70-10993A |
| Деталь: | FRAME-CASSETTE |
| Парткод: | JC72-41183A |
| Деталь: | PMO-GUIDE REAR |
| Парткод: | JC72-41180A |
| Деталь: | ELA HOU-CVR_MAIN |
| Парткод: | JC96-01365A |
| Деталь: | ELA HOU-CVR_MAIN |
| Парткод: | JC96-01364A |
| Деталь: | SPRING-HOOK LEVER |
| Парткод: | 6107-000133 |
| Деталь: | LEVER-HOOK |
| Парткод: | JC72-40325A |
| Деталь: | PLATE-SPRING, DEV |
| Парткод: | JC70-10223A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000002 |
| Деталь: | SPRING-COVER OPEN, L |
| Парткод: | JC61-70944A |
| Деталь: | STACKER-SUB |
| Парткод: | JC72-41220A |
| Деталь: | HINGE-HSG, R |
| Парткод: | JC72-41216A |
| Деталь: | SHAFT-COVER OPEN |
| Парткод: | JC70-10228A |
| Деталь: | PAD-DUMMY |
| Парткод: | JC73-30912A |
| Деталь: | BRUSH-ANTI |
| Парткод: | JC74-40902A |
| Деталь: | GROUND-ANTI |
| Парткод: | JC70-11057A |
| Деталь: | GUIDE-DUMMY |
| Парткод: | JC72-41111A |
| Деталь: | COVER-EXIT |
| Парткод: | JC72-41221A |
| Деталь: | LOCKER-EXIT |
| Парткод: | JC72-41286A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196A |
| Деталь: | COVER-MAIN |
| Парткод: | JC72-41214A |
| Деталь: | BUTTON-C/O |
| Парткод: | JC72-40336D |
| Деталь: | SPRING-CS (BUTTON) |
| Парткод: | 6107-000117 |
| Деталь: | SPRING-COVER OPEN, R |
| Парткод: | JC61-70945A |
| Деталь: | COVER-FRONT, LED |
| Парткод: | JC72-41215F |
| Деталь: | COVER-FRONT, XAR |
| Парткод: | JC72-41215E |
| Деталь: | WINDOW-LED |
| Парткод: | JC72-41397A |
| Деталь: | BUTTON-PANEL, LED |
| Парткод: | JC72-41219A |
| Деталь: | PBA-PANEL, LED |
| Парткод: | JC92-00346A |
| Деталь: | CAP-PANEL WIRE |
| Парткод: | JC72-41222A |
| Деталь: | MEA RACK-FEEDER CAS |
| Парткод: | JC97-01077A |
| Деталь: | PMO-TRAY-MANUAL |
| Парткод: | JC72-41387A |
| Деталь: | PMO-HOLDER FINGER |
| Парткод: | JC72-41182A |
| Деталь: | IMP, FINGER |
| Парткод: | JC70-10213A |
| Деталь: | IMP, GUIDE PLATE-PAPER |
| Парткод: | JC70-10219A |
| Деталь: | SPRING-KNOCK UP |
| Парткод: | JC61-70951A |
| Деталь: | LOCKER-PLATE |
| Парткод: | JC72-41210A |
| Деталь: | MMP, PAD |
| Парткод: | JC73-10911A |
| Деталь: | LABEL-PLATE |
| Парткод: | JC68-30929A |
| Деталь: | IPR-PLT KNOCK UP(12) |
| Парткод: | JC70-11022A |
| Деталь: | SPRING-LOCKERPLATE |
| Парткод: | JG61-70531A |
| Деталь: | LABEL-HEIGHT |
| Парткод: | JG68-30572A |
| Деталь: | PMO-GUIDE LEGAL |
| Парткод: | JC72-41393A |
| Деталь: | IPR-BRACKET_LEGAL |
| Парткод: | JC70-11086A |
| Деталь: | PMO-GUIAE_LETTER |
| Парткод: | JC72-41392A |
| Деталь: | IPR-BRACKET_LETTER |
| Парткод: | JC70-11087A |
| Деталь: | IPR-TENSION_LETTER |
| Парткод: | JC70-11085A |
| Деталь: | PMO-ADJUSTER_S CAST |
| Парткод: | JC72-41394A |
| Деталь: | IPR-GUIDE-PLATE |
| Парткод: | JC70-10993A |
| Деталь: | PMO-FRAME_CASSETTE, P |
| Парткод: | JC72-41382A |
| Деталь: | SCREW-TAPTITE M3x10 FH, WHITE |
| Парткод: | 6003-000002 |
| Деталь: | GUIDE-CASSETTE, M |
| Парткод: | JC72-00013A |
| Деталь: | PMO-GUIDE SUB CAST. |
| Парткод: | JC72-41225A |
| Деталь: | PMO-GUIDE REAR |
| Парткод: | JC72-41180A |
| Деталь: | ELA HOU-MOTOR MAIN |
| Парткод: | JC96-01099A |
| Деталь: | IPR-BRKT_GEAR |
| Парткод: | JC70-10984A |
| Деталь: | SCREW-MACHINE M3x6 |
| Парткод: | 6001-000131 |
| Деталь: | GEAR-FUSER DRIVE |
| Парткод: | JC66-40378A |
| Деталь: | GEAR-125/18 |
| Парткод: | JC66-40376A |
| Деталь: | IPR-BRKT, MOTOR |
| Парткод: | JC70-10985A |
| Деталь: | MOTOR-STEP |
| Парткод: | 3101-001144 |
| Деталь: | GEAR-132/50 (12) |
| Парткод: | JC66-40959A |
| Деталь: | GEAR-IDLE, FU |
| Парткод: | JC66-40377A |
| Деталь: | GEAR-IDLE OPC (12) |
| Парткод: | JC66-40960A |
| Деталь: | GEAR-OPC DRV2 |
| Парткод: | JC66-40001A |
| Деталь: | GEAR-OPC DRIVE (12) |
| Парткод: | JC66-40961A |
| Деталь: | GEAR-FEED DRV (12) |
| Парткод: | JC66-40962A |
| Деталь: | FILM-BRACKET |
| Парткод: | JC73-00002A |
| Деталь: | ELAHOU-FRAME (12) |
| Парткод: | JC96-01338B |
| Деталь: | SHEET COVER OPC |
| Парткод: | JC72-40909A |
| Деталь: | GUIDE-SKEW(12) |
| Парткод: | JC72-41350A |
| Деталь: | ACTUATOR-FEED(12) |
| Парткод: | JC72-00012A |
| Деталь: | Spring-CS |
| Парткод: | 6107-000104 |
| Деталь: | CONNECTOR TERMINAL2 |
| Парткод: | 3712-000165 |
| Деталь: | SCREW-TAPTITE 310 |
| Парткод: | 6003-000002 |
| Деталь: | CONNECTOR TERMINAL1 |
| Парткод: | 3712-000166 |
| Деталь: | GROUND-PLT MOTOR |
| Парткод: | JC70-10013A |
| Деталь: | CBF HARNESS |
| Парткод: | JC39-40576A |
| Деталь: | ROLLER EXIT MAIN |
| Парткод: | JC72-41081A |
| Деталь: | GROUND-OPC(12) |
| Парткод: | JC70-11070A |
| Деталь: | GUIDE-DUST |
| Парткод: | JC70-11068A |
| Деталь: | MOTOR BOARD |
| Парткод: | JC92-01045A |
| Деталь: | ELA-DEVELOPER, GUID |
| Парткод: | JC96-00290A |
| Деталь: | FAN DC 24V |
| Парткод: | 3103-001049 |
| Деталь: | SWITCH |
| Парткод: | JC39-00004A |
| Деталь: | MEA RACK-BRKT_EXIT |
| Парткод: | JC97-01198A |
| Деталь: | EARTH PLATE FUSER |
| Парткод: | JC70-10911A |
| Деталь: | ELA HOU-PTL |
| Парткод: | JC96-01150A |
| Деталь: | CBF HARNESS |
| Парткод: | JC39-40546A |
| Деталь: | GND PLATE G/TR |
| Парткод: | JC70-10980A |
| Деталь: | GROUND-EXIT |
| Парткод: | JC70-11058A |
| Деталь: | MEA RACK-TR HOLDER, L |
| Парткод: | JC97-01079A |
| Деталь: | Roller-Transfer |
| Парткод: | JC75-10962A |
| Деталь: | HEA RACK-HOU EXIT |
| Парткод: | JC97-01104A |
| Деталь: | MEA RACK-TR HOLDER, R |
| Парткод: | JC97-01071A |
| Деталь: | GEAR-TRANSFER (12) |
| Парткод: | JC66-40949A |
| Деталь: | LSU-HARNESS |
| Парткод: | JC39-40540A |
| Деталь: | CBF-HARNESS |
| Парткод: | JG39-40179A |
| Деталь: | GUIDE-FUSER |
| Парткод: | JC72-41223A |
| Деталь: | BASE FRAME |
| Парткод: | JC72-41113A |
| Деталь: | SHIELD CAP WIRE |
| Парткод: | JC70-10003A |
| Деталь: | SHIELD ICU |
| Парткод: | JC70-10225A |
| Деталь: | CBF HARNESS |
| Парткод: | JC39-40009A |
| Деталь: | FILM-EMI |
| Парткод: | JC74-10908A |
| Деталь: | DAMPER-PLATE |
| Парткод: | JC72-41288A |
| Деталь: | GROUND-ICU |
| Парткод: | JC70-10006A |
| Деталь: | GUIDE-TRANSFER |
| Парткод: | JC70-1 0220A |
| Деталь: | SHEET GUIDE-TR |
| Парткод: | JC74-10907A |
| Деталь: | SCREW-TAPTITE 38 |
| Парткод: | 6003-000119 |
| Деталь: | PLATE-SAW |
| Парткод: | JC70-10232A |
| Деталь: | HOLDER-SAW PLATE |
| Парткод: | JC72-40247A |
| Деталь: | ELA HOU-THERMISTOR |
| Парткод: | JC96-01148A |
| Деталь: | SPRING-CVR OPEN (12) |
| Парткод: | JC61-70964A |
| Деталь: | ACTUATOR-C/O |
| Парткод: | JC72-40269A |
| Деталь: | ELA-DEVELOPER, GUID |
| Парткод: | JC96-00291A |
| Деталь: | ROM COVER |
| Парткод: | JC72-41186A |
| Деталь: | MEA RACK-EMPTY_ACT |
| Парткод: | JC97-01207A |
| Деталь: | ACTUATOR-TR |
| Парткод: | JC72-41287A |
| Деталь: | HOLDER-ACTUATOR |
| Парткод: | JC72-41289A |
| Деталь: | PBA MAIN-CLN |
| Парткод: | JC92-01084A |
| Деталь: | CBF-HARNESS |
| Парткод: | JC39-4051 3A |
| Деталь: | ELA-HOU CLEANING PLT |
| Парткод: | JC96-01229A |
| Деталь: | CAP-GND WIRE |
| Парткод: | JC72-00011A |
| Деталь: | CBF-HARNESS MOTOR |
| Парткод: | JC39-40575A |
| Деталь: | ROLLER EXIT FR |
| Парткод: | JC72-41082A |
| Деталь: | Spring-CS |
| Парткод: | 6107-000106 |
| Деталь: | HOLDER-EXIT |
| Парткод: | JC72-41080A |
| Деталь: | GUIDE-DEV L |
| Парткод: | JC72-40274A |
| Деталь: | SPRING-PS G/DEV |
| Парткод: | JC61-70001A |
| Деталь: | GEAR-EXIT/U ID |
| Парткод: | JC66-40006A |
| Деталь: | RING-C ID3 |
| Парткод: | 6044-000159 |
| Деталь: | GEAR-EXIT, IDLE(Z17) |
| Парткод: | JC66-40964A |
| Цена: | 500 ₽ |
| Деталь: | BRACKET_EXIT |
| Парткод: | JC70-11075A |
| Деталь: | EARTH TRNAS (12) |
| Парткод: | JC70-11023A |
| Деталь: | HOLDER-PTL |
| Парткод: | JC72-41187A |
| Деталь: | PBA MAIN PTL |
| Парткод: | JC92-01050A |
| Деталь: | CBF HARNESS |
| Парткод: | JC39-40543A |
| Деталь: | BUSHING-TR12 (L) |
| Парткод: | JC72-41283A |
| Деталь: | SPRING-TR (12) |
| Парткод: | JC61-70940A |
| Деталь: | HOLDER-TR L (12) |
| Парткод: | JC72-41285A |
| Деталь: | SPRING-PLATE (12) |
| Парткод: | JC70-11050A |
| Деталь: | GEAR-EXIT |
| Парткод: | JC66-40209A |
| Цена: | 260 ₽ |
| Деталь: | BEARING-EXIT |
| Парткод: | JC75-10529A |
| Деталь: | ROLL EXIT FR/UP |
| Парткод: | JC75-10957A |
| Деталь: | MEA Rack-Exit Roller |
| Парткод: | JC97-01098A |
| Деталь: | HOUSING-EXIT (250) |
| Парткод: | JC72-41114A |
| Деталь: | BUSHING-TR12 (R) |
| Парткод: | JC72-41060A |
| Деталь: | HOLDER-TR R (12) |
| Парткод: | JC72-41062A |
| Деталь: | GUIDE-DEV R |
| Парткод: | JC72-40275A |
| Деталь: | SPRING-EMPTY |
| Парткод: | JC61-70965A |
| Деталь: | ACTUATOR-EMPTY12 |
| Парткод: | JC72-41290A |
| Деталь: | ELA HOU-SCF(ML-6050) |
| Парткод: | JC96-01268A |
| Деталь: | E-ring |
| Парткод: | 6044-000126 |
| Деталь: | BEARING ROLLER IDLER |
| Парткод: | JC66-10304A |
| Деталь: | TAPTITE SCREW |
| Парткод: | 6003-000179 |
| Деталь: | TAPTITE SCREW |
| Парткод: | 6003-000344 |
| Деталь: | FOOT RUBBER |
| Парткод: | JC61-40301A |
| Деталь: | GUIDE INNER UPPER |
| Парткод: | JC72-40307B |
| Деталь: | Gear-Feed |
| Парткод: | JC66-40014A |
| Деталь: | ROLLER-INNER UPPER |
| Парткод: | JC75-10028A |
| Деталь: | E-ring |
| Парткод: | 6044-000125 |
| Деталь: | GEAR DOUBLE OPTION |
| Парткод: | JC66-40363A |
| Деталь: | BRKT MOTOR (SCF) |
| Парткод: | JC70-10986A |
| Деталь: | STEP MOTOR |
| Парткод: | 3101-001158 |
| Деталь: | SHIELD-PCB |
| Парткод: | JC70-10451A |
| Деталь: | COVER-LEFT |
| Парткод: | JC72-40368B |
| Деталь: | TAPTITE SCREW |
| Парткод: | 6002-000194 |
| Деталь: | MACHINE SCREW |
| Парткод: | 6001-000131 |
| Деталь: | SOLENOID-MAGNET |
| Парткод: | JC33-10001A |
| Деталь: | HUB CLUTCH |
| Парткод: | JC72-40587A |
| Деталь: | SPRING-TS,CLUTCH |
| Парткод: | JC61-70331A |
| Деталь: | GEAR IDLER OPTION |
| Парткод: | JC66-40365A |
| Деталь: | GEAR IDLE Z19 |
| Парткод: | JC66-40012A |
| Деталь: | GUIDE RAIL |
| Парткод: | JC72-40371A |
| Деталь: | BEARING-FEED |
| Парткод: | JC72-40531A |
| Деталь: | GEAR P/UP OPTION |
| Парткод: | JC66-40364A |
| Деталь: | COLLAR CLUTCH P1 |
| Парткод: | JC72-40569B |
| Деталь: | CBF HARNESS |
| Парткод: | JC39-40544A |
| Деталь: | PBA MAIN |
| Парткод: | JC92-01077A |
| Деталь: | CBF HARNESS |
| Парткод: | JC39-40305A |
| Деталь: | Label Warning |
| Парткод: | JC68-20417A |
| Деталь: | LABEL(R)-SCF(12) |
| Парткод: | JC68-30936A |
| Деталь: | Cover-Rear |
| Парткод: | JC72-40362B |
| Деталь: | FRAME UPPER |
| Парткод: | JC70-10027A |
| Деталь: | FRAME LEFT(SCF) |
| Парткод: | JC70-10023A |
| Деталь: | ACTUATOR-ARM |
| Парткод: | JC72-40370A |
| Деталь: | CS STOP RING |
| Парткод: | 6044-000001 |
| Деталь: | PIN PARELLED,P/U |
| Парткод: | JC70-40360A |
| Деталь: | STOPPER-SCF |
| Парткод: | JC72-41347A |
| Деталь: | MACHINE SCREW |
| Парткод: | 6001-001532 |
| Деталь: | FRAME LOWER |
| Парткод: | JC70-11065A |
| Деталь: | SHAFT PICKUP |
| Парткод: | JC70-40002A |
| Деталь: | IDLE-SCF |
| Парткод: | JC72-41 348A |
| Деталь: | HODER-HOUSING |
| Парткод: | JC72-40654A |
| Деталь: | RUBBER P/UP |
| Парткод: | JC73-40907A |
| Деталь: | BRKT SUPPORT |
| Парткод: | JC70-10461A |
| Деталь: | COVER-RIGHT |
| Парткод: | JC72-40367B |
| Деталь: | TAPTITE SCREW |
| Парткод: | 6003-000205 |
| Деталь: | GROUND ROLLER |
| Парткод: | JC70-10467A |
| Деталь: | FRAME RIGHT(SCF) |
| Парткод: | JC70-10022A |
| Деталь: | MACHINE SCREW |
| Парткод: | 6001-000153 |
| Деталь: | CABLE CLAMP |
| Парткод: | 6502-000003 |
| Деталь: | MEA RACK-FEEDER |
| Парткод: | JC97-01078A |
| Деталь: | PLT, GEAR-PICK UP |
| Парткод: | JC66-40219A |
| Деталь: | Washer-Plain |
| Парткод: | 6031-000021 |
| Деталь: | PLT, BEARING-PICK UP |
| Парткод: | JC66-10202A |
| Деталь: | IMP, SHAFT-PICK UP |
| Парткод: | JC70-10231A |
| Деталь: | PLT, LEVER-PICK UP |
| Парткод: | JC72-40254A |
| Деталь: | SPRING PICK-UP |
| Парткод: | JC61-70966A |
| Деталь: | PLT, FRAME-FEED |
| Парткод: | JC72-41115A |
| Деталь: | PMP, IDLE-PICKUP |
| Парткод: | JC72-41234A |
| Деталь: | PLT, HOUSING-PICK UP |
| Парткод: | JC72-40252A |
| Деталь: | PLT, RUBBER-PICKUP |
| Парткод: | JC73-40907A |
| Деталь: | IMP, GUIDE-FEED |
| Парткод: | JC70-10992A |
| Деталь: | SPRING-FEED (2) |
| Парткод: | JC61-70942A |
| Деталь: | PLT, HOLDER-FEED2 |
| Парткод: | JC72-41185A |
| Деталь: | PLT, SUB HOLER-FEED, SMALL |
| Парткод: | JC72-40266A |
| Деталь: | PLT, ROLLER-FEED, LARGE |
| Парткод: | JC72-40261A |
| Деталь: | PLT, ROLLER-FEED, SMALL |
| Парткод: | JC72-40262A |
| Деталь: | IMP, SHAFT-FEED, IDLER |
| Парткод: | JC70-10230A |
| Деталь: | PLT, ROLLER-FEED, DRIVE |
| Парткод: | JC72-41295A |
| Деталь: | SCREW (M3X6 FH+, BLK) |
| Парткод: | 6003-000002 |
| Деталь: | PLT, HOLDER-FEED1 |
| Парткод: | JC72-41184A |
| Деталь: | SPRING-FEED (1) |
| Парткод: | JC61-70941A |
| Деталь: | IMP, SHAFT-FEED |
| Парткод: | JC70-10229A |
| Деталь: | PLT, GEAR-FEED |
| Парткод: | JC66-40375A |
| Деталь: | PLT, GEAR-P/UP DRIVE |
| Парткод: | JC66-40219A |
| Деталь: | IMP, GND-FEED |
| Парткод: | JC70-10991A |
| Деталь: | MEA RACK-FEEDER CAS |
| Парткод: | JC97-01077A |
| Деталь: | MEC-BRKT, BASE R |
| Парткод: | JC75-10922A |
| Деталь: | MEA RACK-FEEDER. |
| Парткод: | JC97-01078A |
| Деталь: | ELAHOU-FRAME(12) |
| Парткод: | JC96-01092A |
| Деталь: | ELA HOU-MOTOR MAIN |
| Парткод: | JC96-01099A |
| Деталь: | ELA-DEVE UNIT |
| Парткод: | ML+6000D5 |
| Деталь: | UNIT-LSU |
| Парткод: | JC59-10507A |
| Деталь: | ELA HOU-CVR_MAIN |
| Парткод: | JC96-01365A |
| Деталь: | ELA HOU-CVR_MAIN |
| Парткод: | JC96-01364A |
| Деталь: | ELA HOU-FUSER_220,KR |
| Парткод: | JC96-01280A |
| Деталь: | ELA HOU-CONTROLLER_K |
| Парткод: | JC96-00982A |
| Деталь: | ELA HOU-CONTROLLER_K |
| Парткод: | JC96-00982B |
| Деталь: | PRO-COVER_SIMM |
| Парткод: | JC72-41224A |
| Деталь: | IPR-SHIELD SIMM |
| Парткод: | JC70-10234A |
| Деталь: | MEC-BRKT, BASE |
| Парткод: | JC75-10920B |
| Деталь: | ELA HOU-ENG BD(220) |
| Парткод: | JC96-01228A |
| Деталь: | ELAHOU-ENG BD(110) |
| Парткод: | JC96-01236A |
| Деталь: | ELAHOU-FUSER(110V) |
| Парткод: | JC96-01093A |
| Деталь: | ELA HOU-FUSER(220V) |
| Парткод: | JC96-01094A |
| Деталь: | CBF-HARNESS-FU(110) |
| Парткод: | JC39-40609A |
| Деталь: | CBF-HARNESS-FU(220) |
| Парткод: | JC39-40610A |
| Деталь: | SCREW-MACHINE M3x6, BH+ |
| Парткод: | 6001-000131 |
| Деталь: | SCREW-TAPTITE M3x12, FH+ |
| Парткод: | 6003-000198 |
| Деталь: | THERMISTOR-NTC |
| Парткод: | 1404-001117 |
| Деталь: | SCREW-TAPTITE M3x8, BH+ |
| Парткод: | 6003-000119 |
| Деталь: | NPR-ELECTRODE FU R |
| Парткод: | JC71-10201A |
| Деталь: | PMO-ROLLER EXIT F/UP |
| Парткод: | JC72-40342A |
| Деталь: | SPRING-PS, EXIT F/UP |
| Парткод: | JC70-11067A |
| Деталь: | PMO-ACTUATOR EXIT |
| Парткод: | JC72-41079A |
| Деталь: | BEARING-EXIT FU |
| Парткод: | JC66-10201A |
| Деталь: | IPR-FUSER LOWER |
| Парткод: | JC70-10983A |
| Деталь: | PMO-BUSHING PR |
| Парткод: | JC72-41078A |
| Деталь: | SPRING-PR |
| Парткод: | JC61-70923A |
| Деталь: | PMO-BUSHING HR, R |
| Парткод: | JC72-41077A |
| Деталь: | NEX-ROLLER HEAT |
| Парткод: | JC71-20901A |
| Деталь: | MEC-ROLLER PRESSURE |
| Парткод: | JC75-10956A |
| Деталь: | PMO-GUIDE PATH |
| Парткод: | JC72-41074A |
| Деталь: | PMO-BUSHING HR, L |
| Парткод: | JC72-41076A |
| Деталь: | GEAR-FUSER |
| Парткод: | JC66-40926A |
| Деталь: | MEC-ROLLER EXIT, FU/LR |
| Парткод: | JC75-10955A |
| Деталь: | PMO-FUSER REAR |
| Парткод: | JC72-41075A |
| Деталь: | LAMP-HALOGEN |
| Парткод: | 4713-001075 |
| Деталь: | LAMP-HALOGEN |
| Парткод: | 4713-001076 |
| Деталь: | BEARING-EXIT FU L |
| Парткод: | JC66-10200A |
| Деталь: | GEAR-EXIT |
| Парткод: | JC66-40209A |
| Цена: | 260 ₽ |
| Деталь: | PMO-FUSER UPPER |
| Парткод: | JC72-41073A |
| Деталь: | Ring-CS |
| Парткод: | 6044-000001 |
| Деталь: | GEAR-EXIT, L/ID |
| Парткод: | JC66-40964A |
| Цена: | 500 ₽ |
| Деталь: | NPR-ELECTRODE FUSER |
| Парткод: | JC71-10902A |
| Деталь: | THERMOSTAT |
| Парткод: | 4712-000001 |
| Деталь: | PMO-CLAW SEPARATOR |
| Парткод: | JC72-41064A |
| Деталь: | SPRING-CLAW |
| Парткод: | JC61-70922A |
Коды ошибок
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Описание
| Error code: | 01 |
| Display: | ERROR CONDITION INVALID HEAD |
| Description: | The ERROR light flashes. |
| Causes: | The printhead was replaced with one that is not a genuine Zebra™ printhead. |
| Remedy: | Install a genuine Zebra printhead. |
| Error code: | 02 |
| Display: | ERROR CONDITION RIBBON OUT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | In thermal transfer mode, ribbon is not loaded or incorrectly loaded. In thermal transfer mode, the ribbon sensor is not detecting ribbon that is loaded incorrectly. In thermal transfer mode, media is blocking the ribbon sensor. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly. |
| Remedy: | Load ribbon correctly. 1. Load ribbon correctly. See Load Ribbon on page 64. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Load media correctly. See Load Media on page 58. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Print a sensor profile. See Print Sensor Profile on page 89. The ribbon out threshold (marked by the word RIBBON) is likely too high, above the black area that indicates where the ribbon is detected. 2. Calibrate the sensors or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73. |
| Error code: | 03 |
| Display: | WARNING RIBBON IN |
| Description: | The ERROR light flashes. |
| Causes: | Ribbon is loaded, but the printer is set for direct thermal mode. |
| Remedy: | Ribbon is not required with direct thermal media. If you are using direct thermal media, remove the ribbon. This error message will not affect printing. If you are using thermal transfer media, which requires ribbon, set the printer for Thermal Transfer mode. See Select Print Method on page 81. |
| Error code: | 04 |
| Display: | ERROR CONDITION PAPER OUT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded. |
| Remedy: | Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration. |
| Error code: | 05 |
| Display: | ERROR CONDITION HEAD OPEN |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The printhead is not fully closed. The head open sensor is not working properly. |
| Remedy: | Replace the sensor. |
| Error code: | 06 |
| Display: | THERMISTOR FAULT |
| Description: | The ERROR light flashes. |
| Causes: | The printhead has a faulty thermistor. |
| Remedy: | Replace the printhead. |
| Error code: | 07 |
| Display: | WARNING HEAD COLD, THERMISTOR FAULT, ERROR CONDITION HEAD ELEMENT BAD |
| Description: | The printer stops; the ERROR light is on; the printer cycles through these three messages. |
| Causes: | The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
| Remedy: | Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
| Error code: | 08 |
| Display: | WARNING HEAD COLD |
| Description: | The printer prints while the ERROR light flashes. |
| Causes: | The printhead temperature is approaching its lower operating limit. The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
| Remedy: | Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the printer to a warmer area. Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
| Error code: | 09 |
| Display: | WARNING HEAD TOO HOT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The printhead is over temperature. |
| Remedy: | Allow the printer to cool. Printing automatically resumes when the printhead elements cool to an acceptable operating temperature. |
| Error code: | 10 |
| Display: | DEFRAGMENTING |
| Description: | The printer stops. |
| Causes: | The printer is defragmenting memory. |
| Remedy: | Caution • Do NOT turn off the printer power during defragmenting. Doing so can damage the printer. Allow the printer to finish defragmenting. If you get this error message frequently, check your label formats. Formats that write to and erase memory frequently may cause the printer to defragment often. Using properly coded label formats usually minimizes the need for defragmenting. If this error message does not go away, contact Technical Support. The printer requires service. |
| Error code: | 11 |
| Display: | ERROR CONDITION CUTTER JAM |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | Caution • The cutter blade is sharp. Do not touch or rub the blade with your fingers. The cutter blade is in the media path. |
| Remedy: | Turn off the printer power and unplug the printer. Inspect the cutter module for debris and clean as needed following the cleaning instructions in Clean the Cutter Module on page 135. |
| Error code: | 12 |
| Description: | General print quality issues |
| Causes: | The printer is set at the incorrect print speed. You are using an incorrect combination of labels and ribbon for your application. The printer is set at an incorrect darkness level. The printhead is dirty. Incorrect or uneven printhead pressure. The printhead is improperly balanced. |
| Remedy: | For optimal print quality, set the print speed to the lowest possible setting for your application via control panel, the driver, or the software. See Adjust Print Speed on page 79. You may want to perform the FEED Self Test on page 120. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. For optimal print quality, set the darkness to the lowest possible setting for your application via the control panel, the driver, or the software. See Adjust Print Darkness on page 78. You may want to perform the FEED Self Test on page 120 to determine the ideal darkness setting. Clean the printhead. See Clean the Printhead and Platen Roller on page 131. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Adjust the printhead balance. |
| Error code: | 13 |
| Description: | Long tracks of missing print on several labels |
| Causes: | Print element damaged. |
| Remedy: | Replace the printhead. |
| Error code: | 14 |
| Description: | Wrinkled ribbon |
| Causes: | Ribbon fed through the machine incorrectly. Incorrect burn temperature. Incorrect or uneven printhead pressure. Media not feeding properly; walking from side to side. The strip plate needs adjusting. The printhead needs vertical adjustment. The printhead is improperly balanced. The printhead and platen roller need to be realigned. |
| Remedy: | See Load Ribbon on page 64. Set the darkness to the lowest possible setting for good print quality. See Adjust Print Darkness on page 78. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Make sure that media is snug by adjusting the media guide, or call a service technician. Adjust the printhead balance. |
| Error code: | 15 |
| Description: | Printing too light or too dark over the entire label |
| Causes: | The media or ribbon is not designed for high-speed operation. You are using an incorrect combination of media and ribbon for your application. You are using ribbon with direct thermal media. Incorrect or uneven printhead pressure. |
| Remedy: | Replace supplies with those recommended for high-speed operation. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. Direct thermal media does not require ribbon. To check if you are using direct thermal media, perform the label scratch test in When to Use Ribbon on page 62. Set the pressure to the minimum needed. See Adjust Printhead Pressure on page 70. |
| Error code: | 16 |
| Description: | Smudge marks on labels |
| Causes: | The media or ribbon is not designed for high-speed operation. |
| Remedy: | Replace supplies with those recommended for high-speed operation. |
| Error code: | 17 |
| Description: | Misregistration/skips labels |
| Causes: | The printer is not calibrated. Improper label format. |
| Remedy: | Recalibrate the printer. Use correct label format. |
| Error code: | 18 |
| Description: | Misregistration and misprint of one to three labels |
| Causes: | The platen roller is dirty. Media does not meet specifications. |
| Remedy: | See Clean the Printhead and Platen Roller on page 131. Use media that meets specifications. |
| Error code: | 19 |
| Description: | Vertical drift in top-of-form position |
| Causes: | The printer is out of calibration. Vertical drift occurs during normal printer operation. Note • A vertical drift of ± 4 to 6 dot rows (approximately 0.5 mm) is within normal tolerances. The platen roller is dirty. |
| Remedy: | Recalibrate the printer. Calibrate the printer. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. |
| Error code: | 20 |
| Description: | Vertical image or label drift |
| Causes: | The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media. |
| Remedy: | Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation. |
| Error code: | 21 |
| Description: | The bar code printed on a label does not scan. |
| Causes: | The bar code is not within specifications because the print is too light or too dark. Not enough blank space around the bar code. |
| Remedy: | Perform the FEED Self Test on page 120. Adjust the darkness or print speed settings as necessary. Leave at least 1/8 in. (3.2 mm) between the bar code and other printed areas on the label and between the bar code and the edge of the label. |
| Error code: | 22 |
| Description: | Loss of printing registration on labels. Excessive vertical drift in top-of-form registration. |
| Causes: | The platen roller is dirty. Media guides are positioned improperly. The media type is set incorrectly. The media is loaded incorrectly. |
| Remedy: | Clean the platen roller according to the instructions in Clean the Printhead and Platen Roller on page 131. Ensure that the media guides are properly positioned. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. Load media correctly. See Load Media on page 58. |
| Error code: | 23 |
| Description: | Auto Calibrate failed. |
| Causes: | Media or ribbon is loaded incorrectly. The sensors could not detect the media or ribbon. The sensors are dirty or positioned improperly. The sensors are dirty, or media is positioned improperly for the sensors to detect. The media type is set incorrectly. |
| Remedy: | Ensure that media and ribbon are loaded correctly. Manually calibrate the printer. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Ensure that the sensors are clean and that media is positioned properly. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. |
| Error code: | 24 |
| Description: | A label format was sent to the printer but was not recognized. The DATA light does not flash. |
| Causes: | The communication parameters are incorrect. |
| Remedy: | Check the printer driver or software communications settings (if applicable). If you are using serial communication, check the serial port setting in the control panel menu. See Set Serial Communications on page 91. If you are using serial communication, make sure you are using a null modem cable or a null modem adapter. Using the control panel controls, check the protocol setting. It should be set to NONE. See Set Protocol on page 93. If a driver is used, check the driver communication settings for your connection. |
| Error code: | 25 |
| Description: | A label format was sent to the printer. Several labels print, then the printer skips, misplaces, misses, or distorts the image on the label. |
| Causes: | The serial communication settings are incorrect. |
| Remedy: | Ensure that the flow control settings match. Check the communication cable length. See Table 5 on page 48 for requirements. Check the printer driver or software communications settings (if applicable). |
| Error code: | 26 |
| Description: | A label format was sent to the printer but was not recognized. The DATA light flashes but no printing occurs. |
| Causes: | The prefix and delimiter characters set in the printer do not match the ones in the label format. Incorrect data is being sent to the printer. |
| Remedy: | Verify the prefix and delimiter characters. See Set Format Prefix Character on page 94 and Set Delimiter Character on page 95 for the requirements. Check the communication settings on the computer. Ensure that they match the printer settings. If the problem continues, check the label format. |
| Error code: | 27 |
| Description: | Broken or melted ribbon |
| Causes: | Darkness setting too high. |
| Remedy: | 1. Reduce the darkness setting. 2. Clean the printhead thoroughly. |
| Error code: | 28 |
| Description: | The printer does not detect when the ribbon runs out. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly. |
| Causes: | The ribbon-out threshold is set too high to detect the ribbon. On a sensor profile, the ribbon-out threshold (circled in Figure 15) appears above the black bars that indicate the ribbon. This happens if you calibrate the printer without ribbon and later insert ribbon without recalibrating the printer or loading printer defaults. |
| Remedy: | 1. Print a sensor profile (see Print Sensor Profile on page 89), and note the location of the ribbon-out threshold (circled in Figure 15). 2. Calibrate the printer, this time using ribbon, or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73. Important • Loading defaults resets all printer parameters back to factory defaults. 3. Print another sensor profile, and compare it to the first one. 4. If the ribbon-out threshold is still too high, you may manually change the value. |
| Error code: | 29 |
| Description: | The ribbon light is on even though ribbon is loaded correctly. |
| Causes: | The printer was not calibrated for the label and ribbon being used. |
| Remedy: | Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. |
| Error code: | 30 |
| Description: | The LCD displays a language that I cannot read |
| Causes: | The language parameter was changed through the control panel or a firmware command. |
| Remedy: | 1. Press SETUP/EXIT to enter configuration mode. 2. Press MINUS (-). The printer displays the LANGUAGE parameter in the current language. Even if you cannot recognize the characters displayed, you can still scroll to another language. 3. Press SELECT to select the parameter. 4. Press PLUS (+) or MINUS (-) to scroll through the choices until you find a language that you can read. 5. Press SETUP/EXIT. The LCD displays SAVE CHANGES in the original language. 6. Press SETUP/EXIT again to exit configuration mode and save the changes (if the language does not change, you may need to scroll to a different save option by pressing PLUS (+) or MINUS (-) in the previous step). 7. Repeat this process, if necessary, until you reach the desired language. |
| Error code: | 31 |
| Description: | The LCD is missing characters or parts of characters |
| Causes: | The LCD may need replacing. |
| Remedy: | Run the Power-On Self Test on page 117 and check that the LCD display shows all characters. If not, replace the LCD. |
| Error code: | 32 |
| Description: | Changes in parameter settings did not take effect |
| Causes: | Parameters are set incorrectly. A command turned off the ability to change the parameter. A command changed the parameter back to the previous setting. If the problem continues, there may be a problem with the main logic board. |
| Remedy: | 1. Set parameters and save permanently. 2. Turn the printer off (O) and then on (I). Refer to the ZPL Programming Guide. Refer to the ZPL Programming Guide. Replace the main logic board. |
| Error code: | 33 |
| Description: | The printer fails to calibrate or detect the top of the label. |
| Causes: | The printer was not calibrated for the label being used. The printer is configured for continuous media. The driver or software configuration is not set correctly. |
| Remedy: | Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81. Driver or software settings produce commands that can overwrite the printer configuration. Check the driver or software media-related setting. |
| Error code: | 34 |
| Description: | Non-continuous labels are being treated as continuous labels. |
| Causes: | The printer was not calibrated for the media being used. The printer is configured for continuous media. |
| Remedy: | Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81. |
| Error code: | 35 |
| Description: | All lights are on, but nothing displays on the LCD, and the printer locks up. |
| Causes: | Internal electronic or firmware failure. |
| Remedy: | Turn the printer power off (O) and then on (I). If the printer locks up again, replace the main logic board. |
| Error code: | 36 |
| Description: | The printer locks up while running the Power-On Self Test. |
| Causes: | Main logic board failure. |
| Remedy: | Replace the main logic board. |
| Error code: | 37 |
| Description: | Non-continuous labels are being treated as continuous labels. |
| Causes: | The printer is configured for continuous media. The printer was not calibrated for the media being used. |
| Remedy: | Set the media type to noncontinuous media. See Set Media Type on page 56. Perform the calibration procedure in Calibrate Media and Ribbon Sensors on page 67. |
