Samsung MultiXpress K3250NR
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A4
Число страниц в месяц
60000
Скорость печати
A4
25
Цветность печати
черно-белая
Общие характеристики |
|
|---|---|
Размещение |
настольный |
Макс. формат |
A4 |
Область применения |
средний офис |
Число страниц в месяц |
60 000 |
Печать фотографий |
|
Телефон |
|
Сканер |
|
Копир |
|
Факс |
|
Тип устройства |
МФУ |
Цветность печати |
|
Тип |
лазерный/светодиодный |
Технология печати |
лазерная |
Принтер |
|
Макс, ширина отпечатка |
216 |
Время разогрева |
25 |
Прямая печать |
|
Двусторонняя печать |
|
Печать без полей |
|
Макс, длина отпечатка |
356 |
Макс, разрешение для ч/б печати |
|
| По X | 1 200 |
| По Y | 1 200 |
Скорость ч/б печати |
|
| A4 | 25 |
Время выхода первого отпечатка |
|
| Ч/б | 8,5 |
Копир |
|
Макс, количество копий за цикл |
9 999 |
Время выхода первой копии |
6,2 |
Значение масштаба |
|
| Максимальное | 4 |
| Минимальное | 0,25 |
Макс, разрешение (ч/б) |
|
| По Y | 600 |
| По X | 600 |
Сканер |
|
Макс. формат оригинала |
A4 |
Глубина цвета |
24 бит |
Тип сканера |
планшетный/протяжный |
Слайд-адаптер |
|
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Емкость устройства автоподачи оригиналов |
100 |
Устройство автоподачи оригиналов |
одностороннее |
Макс, размер сканирования |
|
| По Y | 432 |
| По X | 216 |
Разрешение сканера |
|
| По Х | 600 |
| По Х (улучшенное) | 4 800 |
| По Y (улучшенное) | 4 800 |
Скорость сканирования |
|
| Цветн, | 45 |
| Ч/б | 45 |
Расходные материалы |
|
Ресурс ч/б картриджа/тонера |
25 000 |
Ресурс фотобарабана |
100 000 |
Количество картриджей |
1 |
Печать на: |
|
| Пленках |
|
| Карточках |
|
| Этикетках |
|
| Конвертах |
|
| Глянцевой бумаге |
|
| Матовой бумаге |
|
| Рулоне |
|
| CD/DVD |
|
| Фотобумаге |
|
Плотность бумаги |
|
| Минимальная | 60 |
| Максимальная | 176 |
Факс |
|
Макс, скорость передачи данных |
33,6 Кбит/с |
PC Fax |
|
Телефон |
|
Беспроводная трубка |
|
Проводная трубка |
|
Спикерфон |
|
Стандарт DECT |
|
АОН |
|
Автоответчик |
|
Caller ID |
|
Языки управления |
|
|
|
|
| PCL 5e |
|
| PostScript 3 |
|
| PostScript |
|
| PCL 6 |
|
| PCL 5c |
|
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
| Максимальная | 2 180 |
| Стандартная | 1 140 |
Вывод бумаги |
|
| Стандартный | 500 |
Интерфейсы |
|
Версия USB |
2,0 |
USB |
|
Веб-интерфейс |
|
Ethernet (RJ-45) |
|
Устройство для чтения карт памяти |
|
RS-232 |
|
FireWire (IEEE 1394) |
|
Wi-Fi |
|
Bluetooth |
|
Инфракрасный порт |
|
AirPrint |
|
LPT |
|
Память/Процессор |
|
Частота процессора |
1 000 |
Объем памяти |
1 520 |
Макс, объем памяти |
1 520 |
Дополнительная информация |
|
Работа от аккумулятора |
|
Диагональ дисплея |
7 |
Экран |
|
Поддержка ОС |
|
| Mac OS |
|
| Windows |
|
| Linux |
|
Потребляемая мощность |
|
| При работе | 1 750 |
| В режиме ожидания | 1,5 |
Уровень шума |
|
| При работе | 58,3 |
Габариты |
|
Высота |
820 |
Вес |
58,3 |
Ширина |
566 |
Глубина |
620 |
Модули
FRAME-MAN REGI
CASSETTE-2ND
MAIN
FRAME-PICKUP 1ST
RADF
(Узел термозакрепления)
MP
FRAME MAIN ENGINE
COVER
FRAME-PICKUP 2ND
DRIVE-M FUSER EXIT
OPE
FRAME FRONT and REAR
CASSETTE-1ST
RADF FRAME MAIN
PLATEN
PLATEN LOWER
COVER-SIDE MONO
RADF PLATEN
Exit
Детали FRAME FRONT and REAR
| Деталь: | FRAME-MAIN REGI, X4300 |
| Парткод: | JC93-00910A |
| Деталь: | PHOTO-INTERRUPTER, DIODE,DIP |
| Парткод: | 0604-001381 |
| Деталь: | SHAFT-REGI, CLX-9201,SUM 23,361.9,14.7,ST |
| Парткод: | JC66-03302A |
| Деталь: | ROLLER FEED-REGI, X4300/K4350,EPDM,SUM23, |
| Парткод: | JC66-04130A |
| Деталь: | GEAR-ROLLER REGI, CLX-9201,POM,0.8,21,NAT |
| Парткод: | JC66-03293A |
| Деталь: | SPRING-ES, SWPB,0.9,22.4,8.1 |
| Парткод: | 6107-003302 |
| Деталь: | HOLDER-SHAFT REGI, CLX-9201,POM,5,BLACK,A |
| Парткод: | JC61-04897A |
| Деталь: | BRACKET-REGI UPPER, CLX-9201,EGI-SECC,T0. |
| Парткод: | JC61-04685A |
| Деталь: | CASSETTE-2ND, X3220,MX4N,300mm,55mm,Lifti |
| Парткод: | JC90-01141C |
| Деталь: | CASSETTE FRAME-2ND, X3220 |
| Парткод: | JC90-01188C |
| Деталь: | CASSETTE SUB-COVER, X3220 |
| Парткод: | JC90-01277B |
| Деталь: | SEAL-PAD CST, CLX-9201,CIGAL,BLK,0.7,47,1 |
| Парткод: | JC62-00946A |
| Деталь: | PLATE-KNOCK UP, CLX-9201,EGI-SECC,0.8T,36 |
| Парткод: | JC61-04767A |
| Деталь: | GEAR-M_PINION 24, SCX-6345N/XRX,POM,1,24, |
| Парткод: | JC66-01020A |
| Деталь: | INDICATOR-SIZE SIDE, CLX-9201,ABS,G72797, |
| Парткод: | JC64-00703A |
| Деталь: | GUIDE-LEFT, CLX-9201,HIPS,64,79.3,ICE-GRE |
| Парткод: | JC61-04718A |
| Деталь: | CASSETTE SUB-GUIDE REAR, X4300 |
| Парткод: | JC90-01291A |
| Деталь: | CASSETTE SUB-GUIDE FRONT, X4300 |
| Парткод: | JC90-01290A |
| Деталь: | CASSETTE-BRACKET LIFT, CLX-9201,SEC |
| Парткод: | JC90-01128A |
| Деталь: | CASSETTE SUB-LIFTING GEAR, CLX-9201 |
| Парткод: | JC90-01588A |
| Деталь: | LOCKER-CASSETTE 2ND, CLX-9201,POM,BLACK,1 |
| Парткод: | JC64-00716A |
| Деталь: | LEVER-LINK SIZE 2ND, CLX-9201,ABS,21.2,19 |
| Парткод: | JC66-03201A |
| Деталь: | PLATE-LEVER, CLX-9350,EGI-SECC,1.6T,73.6, |
| Парткод: | JC61-03206A |
| Деталь: | ROLLER-IDLE CST, CLX-9350,POM,OD10,L16.5, |
| Парткод: | JC61-03331A |
| Деталь: | OPE, SL-X3220RX |
| Парткод: | JC97-04718A |
| Деталь: | COVER, SL-K3250RX,SEC |
| Парткод: | JC95-02028A |
| Деталь: | CASSETTE-1ST, X3220,MX4N,300mm,55mm,Lifti |
| Парткод: | JC90-01140C |
| Деталь: | CASSETTE-2ND, X3220,MX4N,300mm,55mm,Lifti |
| Парткод: | JC90-01141C |
| Деталь: | CARTRIDGE-WTB MONO, K4350,SEC,WORLD |
| Парткод: | JC96-09196A |
| Деталь: | HVPS-POLARIS_R MONO, 24V,21.6V26.4V,MAX |
| Парткод: | JC44-00237A |
| Деталь: | LSU, SCX-8123ND,SEC,single,A3,600,Single |
| Парткод: | JC97-04017A |
| Цена: | 14 700 ₽ |
| Деталь: | RADF, X3220,MX3,297mm,25ppm,RADF,100,MD |
| Парткод: | JC97-04726A |
| Деталь: | PLATEN, X3220,NON-MD |
| Парткод: | JC97-04721A |
| Деталь: | EXIT, X4300 |
| Парткод: | JC90-01118B |
| Деталь: | FUSER, MK4N,2RF,1300W,30mm,MD,115V |
| Парткод: | JC91-01212A |
| Деталь: | SENSOR, HSU-07F1V2-N,CLX-9201,045C,+3.3 |
| Парткод: | JC32-00015A |
| Деталь: | COVER SIDE-MONO, K3250,1.4kgf |
| Парткод: | JC95-01923B |
| Деталь: | DRIVE-DUCT, SEC,1.1,478.9,75,GRAY,SCX-81 |
| Парткод: | JC93-00451A |
| Деталь: | DRIVE-M TONER SUPPLY, SEC,SCX-8128NA |
| Парткод: | JC93-00450A |
| Деталь: | DRIVE-PICKUP, SEC,5,BLACK,CLX-9201NA |
| Парткод: | JC93-00442A |
| Деталь: | FDB-V1, SL-X3220,MX3-FDB-V1,AC/AC,1300W,1 |
| Парткод: | JC44-00210B |
| Деталь: | SMPS-V1, M4580,PSPN2-TYPE4-V1,AC-DC,110V |
| Парткод: | JC44-00091D |
| Деталь: | DRIVE-MAIN, K4350,SEC |
| Парткод: | JC93-00912A |
| Деталь: | DRIVE-M FUSER EXIT, SEC,OD30.5,NTR,PART,S |
| Парткод: | JC93-00449A |
| Деталь: | FAN-TYPE 6, 120mA,4.00mmH20,0.424m3/mi |
| Парткод: | JC31-00160C |
| Деталь: | PBA MAIN, K3250 |
| Парткод: | JC92-02831B |
| Деталь: | PBA FAX JOINT, X3220/K3250,MD |
| Парткод: | JC92-02743B |
| Деталь: | COVER-LEFT FAN, X4300,ABS,SPLIT GRAY,HF-0 |
| Парткод: | JC63-02343B |
| Деталь: | SEAL-FILTER LEFT, CLX-9350,PE Foam,BLACK, |
| Парткод: | JC62-00641A |
| Деталь: | CARTRIDGE SUB-DEVE KIT, K3250,SEC |
| Парткод: | JC96-10272A |
| Деталь: | COVER-OPE UPPER, X3220,ABS,T 2.5,SPLIT BR |
| Парткод: | JC63-05301A |
| Деталь: | MOTOR BLDC, 2000rpm,1200gfcm,24V,2.8A,150 |
| Парткод: | JC31-00123A |
| Деталь: | MOTOR BLDC, 2000rpm,1200gfcm,24V,2.8A,150 |
| Парткод: | JC31-00123B |
| Цена: | 3 700 ₽ |
| Деталь: | DRIVE-MAIN SUB, K4350,SEC |
| Парткод: | JC93-00911A |
| Деталь: | FRAME MAIN-PICKUP 1ST, CLX-9201,SEC |
| Парткод: | JC93-00511A |
| Деталь: | FRAME MAIN-PICKUP, CLX-9201,SEC |
| Парткод: | JC93-00510A |
| Деталь: | GUIDE-HARNESS PICKUP, CLX-9201,ABS,84.22, |
| Парткод: | JC61-04723A |
| Деталь: | SHEET-GUIDE PICKUP, CLX-9210,PET,0.188,32 |
| Парткод: | JC63-03342A |
| Деталь: | GUIDE-PICKUP 1ST, CLX-9201,ABS,328.5,50.5 |
| Парткод: | JC61-04721A |
| Деталь: | HARNESS-PICKUP SENSOR, CLX-9201,UL10272,6 |
| Парткод: | JC39-01588A |
| Деталь: | FRAME MAIN-PICKUP UPPER, CLX-9201,SEC |
| Парткод: | JC93-00504A |
| Деталь: | FRAME MAIN-PICKUP LOWER, CLX-9201,SEC |
| Парткод: | JC93-00503A |
| Деталь: | FRAME-MAIN PICK UP ROLLER, CLX-9201,0,EXP |
| Парткод: | JC93-00540A |
| Цена: | 700 ₽ |
| Деталь: | GEAR-PICKUP, CLX-9201,POM,0.8,31,NATURAL( |
| Парткод: | JC66-03281A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | ACTUATOR-EMPTY PICKUP, CLX-9201,POM,M90-4 |
| Парткод: | JC66-03199A |
| Деталь: | GEAR-M_PU JOINT, SCX-6345N/XRX,POM,0.7,21 |
| Парткод: | JC66-00943A |
| Деталь: | HOLDER-M_IDLE ONE WAY, SCX-6345N/XRX,POM, |
| Парткод: | JC61-01288A |
| Деталь: | GEAR-M_IDLE PU, SCX-6345N/XRX,POM,0.7,22, |
| Парткод: | JC66-00940A |
| Деталь: | CLUTCH-P_ONE WAY, SCX-6345N/XRX,STS304,0. |
| Парткод: | JC66-00977A |
| Деталь: | COUPLER-TORQUELIMITER, CLX-9350,WHITE,350 |
| Парткод: | JC67-00455A |
| Деталь: | SPRING-ES, STAINLESS-STS304,0.75,32.5,3.5 |
| Парткод: | 6107-001757 |
| Деталь: | LEVER-INPUT CST, CLX-9201,POM,52.9,28.7,M |
| Парткод: | JC66-03200A |
| Деталь: | HOLDER-RETARD, CLX-9201,POM,137,BLACK,M90 |
| Парткод: | JC61-04732A |
| Деталь: | RADF-COVER OPEN, X3220,NON-MD |
| Парткод: | JC97-04754A |
| Деталь: | DADF-STACKER, SCX-8120ND |
| Парткод: | JC97-04316A |
| Деталь: | COVER-SIDE_F, SCX-8120ND,HIPS,2.5T,SPLIT |
| Парткод: | JC63-04120A |
| Деталь: | COVER-SIDE_R, SCX-8120ND,HIPS,2.5T,SPLIT |
| Парткод: | JC63-04121A |
| Деталь: | RADF-HINGE R, X3220,MD |
| Парткод: | JC97-04728A |
| Деталь: | RADF-HINGE L, X3220,MD |
| Парткод: | JC97-04729A |
| Деталь: | PBA OPTION-ADF, X3220,SEC |
| Парткод: | JC92-02446D |
| Деталь: | RADF-SUB, X3220,NON-MD |
| Парткод: | JC97-04731A |
| Деталь: | COVER-OPEN, SCX-8120ND,HIPS,2T,SPLIT BROW |
| Парткод: | JC63-04122A |
| Деталь: | ROLLER IDLE-IDLE TAKE AWAY, CLX-9350,POM, |
| Парткод: | JC66-02384A |
| Деталь: | ACTUATOR-REGI, CLX-9201,PC,156.8 |
| Парткод: | JC66-03148A |
| Деталь: | SPONGE-COVER OPEN, PUR,3,40,29,GRAY |
| Парткод: | JC63-03890A |
| Деталь: | ACTUATOR-DETECT, CLX-9201,PC,124,BLACK,AC |
| Парткод: | JC66-03147A |
| Деталь: | HANDLE-COVER OPEN, SCX-8120ND,ABS,322,32. |
| Парткод: | JC64-00885A |
| Деталь: | DADF GUIDE-PIKCUP, CLX-9201,SEC |
| Парткод: | JC97-04009A |
| Цена: | 2 500 ₽ |
| Деталь: | LOCKER-STOPPER, CLX-9201,POM,BLACK |
| Парткод: | JC64-00681A |
| Деталь: | STOPPER-PAPER, CLX-9201,POM,35.57,BLACK |
| Парткод: | JC61-04647A |
| Деталь: | GUIDE-STACKER UPPER, SCX-8120ND,HIPS,2T,3 |
| Парткод: | JC61-05930A |
| Деталь: | GUIDE-DOC_R, SCX-8120ND,ABS,2.5T,106.07,7 |
| Парткод: | JC61-05933A |
| Деталь: | GUIDE-DOC_F, SCX-8120ND,ABS,2.5T,106.07,7 |
| Парткод: | JC61-05932A |
| Деталь: | GUIDE-GEAR_RACK_R, CLX-9201,ABS,37.03,224 |
| Парткод: | JC61-04751A |
| Деталь: | GUIDE-GEAR_RACK_F, CLX-9201,ABS,33.08,158 |
| Парткод: | JC61-04750A |
| Деталь: | GEAR, CF4500,POM,NATURAL (WHITE) |
| Парткод: | JF72-41354A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | ACTUATOR-PAPER_LENGTH, CLX-9201,ABS,22,65 |
| Парткод: | JC66-03209A |
| Деталь: | GUIDE-STACKER LOWER, SCX-8120ND,HIPS,2T,3 |
| Парткод: | JC61-05931A |
| Деталь: | GUIDE-STACKER WIRE, SCX-6345N/XRX,STS,PI1 |
| Парткод: | JC61-01438A |
| Деталь: | Печь, в сборе (220В) |
| Парткод: | JC91-01211A |
| Цена: | 28 500 ₽ |
| Деталь: | MP SUB-TRAY, X3220 |
| Парткод: | JC90-01275B |
| Деталь: | MP GUIDE-MAIN, X4300 |
| Парткод: | JC90-01273A |
| Деталь: | MP-BRACKET PICK UP, X4300 |
| Парткод: | JC90-01125B |
| Деталь: | MP-COVER BASE, X4300 |
| Парткод: | JC90-01276A |
| Деталь: | GEAR-IDLE MP, CLX-9201,POM,1,26,NATURAL,2 |
| Парткод: | JC66-03215A |
| Деталь: | GEAR-FORWARD MP, CLX-9201,POM,1,28,30 |
| Парткод: | JC66-03214A |
| Деталь: | MP-PICK UP RUBBER, CLX-9350,SEC |
| Парткод: | JC90-00989A |
| Деталь: | FRAME-TRAY LOWER, X4300/K4350,ABS,780U,SP |
| Парткод: | JC61-06130A |
| Деталь: | FRAME-TRAY PAPER, ABS,SPLIT GRAY,2,HF-066 |
| Парткод: | JC61-05842B |
| Деталь: | FRAME-TRAY COVER, X4300,ABS,SPLIT GRAY,HF |
| Парткод: | JC61-05841B |
| Деталь: | GEAR-RACK F, X4300/K4350,POM,1,NATURAL (W |
| Парткод: | JC66-04060A |
| Деталь: | GEAR-RACK R, X4300/K4350,POM,1,NATURAL (W |
| Парткод: | JC66-04061A |
| Деталь: | GEAR-PINION, SF4000,POM,1.0,Z16,NATURAL(W |
| Парткод: | JG66-40003A |
| Цена: | 260 ₽ |
| Деталь: | FRAME-TRAY UPPER, X4300/K4350,ABS,780U,SP |
| Парткод: | JC61-06129A |
| Деталь: | GUIDE-SIDE R, X4300/K4350,ABS,HF-0660i,SP |
| Парткод: | JC61-06134A |
| Деталь: | GUIDE-SIDE F, X4300/K4350,ABS,HF-0660i,SP |
| Парткод: | JC61-06133A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | COUPLER-TORQUELIMITER, CLX-9350,WHITE,350 |
| Парткод: | JC67-00455A |
| Деталь: | SHEET-GUIDE MP, CLX-9201,PET,0.125,25,308 |
| Парткод: | JC63-03358A |
| Деталь: | SOLENOID-MP, CLX-9350,DC24V,18.4,2730, |
| Парткод: | JC33-00029B |
| Деталь: | MP-ONE WAY, CLX-9350,SEC,-,-,- |
| Парткод: | JC90-00918A |
| Деталь: | ROLLER-IDLE FORWARD, CLX-9350,POM,T8.5,OD |
| Парткод: | JC61-03332A |
| Деталь: | HOLDER-M_IDLE ONE WAY, SCX-6345N/XRX,POM, |
| Парткод: | JC61-01288A |
| Деталь: | GEAR-M PU, CLX-9201,POM,0.7,21,16.1 |
| Парткод: | JC66-03213A |
| Деталь: | STOPPER-PAPER, CLX-9201,POM,9.8,18.2,M90- |
| Парткод: | JC61-04766A |
| Деталь: | LEVER-HOOK, CLX-9201,POM,13.4,15.2,M90-44 |
| Парткод: | JC66-03219A |
| Деталь: | GUIDE-UPPER PU MP, CLX-9201,PC,34.9,61.9, |
| Парткод: | JC61-04876A |
| Деталь: | GEAR-M_IDLE PU, SCX-6345N/XRX,POM,0.7,22, |
| Парткод: | JC66-00940A |
| Деталь: | COVER-INNER SUB, K3250,HIPS,T 2,SPLIT GRA |
| Парткод: | JC63-05306A |
| Деталь: | FRAME-FRONT MONO, K3250,SEC |
| Парткод: | JC93-01261A |
| Деталь: | FRAME-REGI HOLDER DUST, SCX-8040,SEC,WORL |
| Парткод: | JC93-00078B |
| Цена: | 500 ₽ |
| Деталь: | FRAME BASE, CLX-9201,SEC,WORLD |
| Парткод: | JC93-00851A |
| Деталь: | FRAME MAIN-PICKUP 2ND, CLX-9201,SEC,WORLD |
| Парткод: | JC93-00512A |
| Деталь: | FRAME MAIN-PICKUP 1ST, CLX-9201,SEC |
| Парткод: | JC93-00511A |
| Деталь: | FRAME-MAIN REGI, X4300 |
| Парткод: | JC93-00910A |
| Деталь: | FRAME MAIN-FEED SENSOR, X4300 |
| Парткод: | JC93-00924A |
| Деталь: | FRAME-MIDDLE DUCT, K4350,SEC,WORLD |
| Парткод: | JC93-00892A |
| Деталь: | FRAME MAIN-RIGHT CST RAIL, CLX-9201,SEC,W |
| Парткод: | JC93-00478A |
| Деталь: | ROLLER IDLE-FEED, CLX-9201,EPDM,SUS,8 |
| Парткод: | JC66-03203A |
| Деталь: | FRAME-DUCT, K4350,SEC,WORLD |
| Парткод: | JC93-00917A |
| Деталь: | FRAME-MIDDLE SUPPORT FUSER, X4300,SEC,WOR |
| Парткод: | JC93-00467B |
| Деталь: | GUIDE-TONER BOTTLE, SCX-8128NA,HIPS,119.8 |
| Парткод: | JC61-04864A |
| Деталь: | FRAME-SCAN RIGHT ASSY, X3220,SEC |
| Парткод: | JC93-01272A |
| Деталь: | FRAME-REAR MONO, K3250,SEC |
| Парткод: | JC93-01262A |
| Деталь: | FRAME-HV PACKAGE MONO, K4350,SEC,WORLD |
| Парткод: | JC93-00891A |
| Деталь: | FRAME-DUCT SUCTION, K4350,SEC,WORLD |
| Парткод: | JC93-00893A |
| Деталь: | HOLDER-SAW, SCX-8040,ABS+PC,22.9,18.2,45. |
| Парткод: | JC61-03574A |
| Деталь: | STOPPER-REGI, CLX-9201,ABS+PC,25.8,6.6,NH |
| Парткод: | JC61-04900A |
| Деталь: | FRAME MAIN-GEAR CLUTCH ASSY, CLX-9201,SEC |
| Парткод: | JC93-01186A |
| Деталь: | PLATE-LSU LOWER, SCX-8128NA,EGI-SECC,T1.2 |
| Парткод: | JC61-04834A |
| Деталь: | PHOTO-INTERRUPTER, DIODE,DIP |
| Парткод: | 0604-001381 |
| Деталь: | FAN, Type7,24,170mA,0.949m3/mi |
| Парткод: | JC31-00161A |
| Деталь: | DUCT-SUCTION LOWER, K4350,ABS,HF-0660I,BL |
| Парткод: | JC67-00739A |
| Деталь: | DUCT-SUCTION UPPER, K4350,ABS,HF-0660I,BL |
| Парткод: | JC67-00740A |
| Деталь: | COVER-FRONT, K3250,SEC |
| Парткод: | JC95-02042A |
| Деталь: | COVER-INNER, K4350,SEC |
| Парткод: | JC95-01903A |
| Деталь: | COVER-MIDDLE RIGHT, X3220,ABS,T 2.5,SPLIT |
| Парткод: | JC63-05298A |
| Деталь: | COVER-SCAN FRONT, SL-X3220RX,SEC |
| Парткод: | JC95-02029A |
| Деталь: | COVER-LEFT, K4350,SEC |
| Парткод: | JC95-01913A |
| Деталь: | COVER-LEFT TOP, X4300,ABS,T 2.5,SEC,SPLIT |
| Парткод: | JC63-04534A |
| Деталь: | COVER-SCAN LEFT, X3220,ABS,T 2.5,SPLIT BR |
| Парткод: | JC63-05295A |
| Деталь: | COVER-LEFT UPPER, X4300,ABS,T 2.5,SEC,9AA |
| Парткод: | JC63-04521A |
| Деталь: | COVER-EXIT, X4300,SEC |
| Парткод: | JC95-01911A |
| Деталь: | COVER-EXIT REAR, X4300,SEC |
| Парткод: | JC95-01912A |
| Деталь: | COVER-EXIT DUMMY, X4300,ABS,T 2.5,SEC,9AA |
| Парткод: | JC63-04526A |
| Деталь: | COVER-FRONT LOWER, X4300,HIPS,T 2.0,SEC,S |
| Парткод: | JC63-04536A |
| Деталь: | COVER-RIGHT FRONT MONO, K4350,ABS,T 2.5,S |
| Парткод: | JC63-04539A |
| Деталь: | COVER-RIGHT REAR MONO, K4350,ABS,T 2.5,SE |
| Парткод: | JC63-04540A |
| Деталь: | COVER-RIGHT UPPER, X4300,ABS,T 2.5,SEC,9A |
| Парткод: | JC63-04520A |
| Деталь: | COVER-SCAN RIGHT, X3220,ABS,T 2.5,SPLIT B |
| Парткод: | JC63-05296A |
| Деталь: | COVER-REAR LOWER MONO, K4350,ABS,T 2.5,SE |
| Парткод: | JC63-04542A |
| Деталь: | COVER-REAR UPPER, X4300,ABS,T 2.5,SEC,9AA |
| Парткод: | JC63-04522A |
| Деталь: | COVER-REAR UPPER DUMMY, X4300,ABS,T 2.5,S |
| Парткод: | JC63-04528A |
| Деталь: | COVER-SCAN REAR, X3220,ABS,T 2.5,SPLIT BR |
| Парткод: | JC63-05297A |
| Деталь: | COVER-REAR DUMMY, X4300,ABS,T 2.0,SPLIT B |
| Парткод: | JC63-04567A |
| Деталь: | FRAME MAIN-PICKUP 2ND, CLX-9201,SEC,WORLD |
| Парткод: | JC93-00512A |
| Деталь: | FRAME MAIN-PICKUP, CLX-9201,SEC |
| Парткод: | JC93-00510A |
| Деталь: | GUIDE-HARNESS PICKUP, CLX-9201,ABS,84.22, |
| Парткод: | JC61-04723A |
| Деталь: | SHEET-GUIDE PICKUP, CLX-9210,PET,0.188,32 |
| Парткод: | JC63-03342A |
| Деталь: | GUIDE-PICKUP BOTTOM, CLX-9201,ABS,16.8,33 |
| Парткод: | JC61-04735A |
| Деталь: | HARNESS-PICKUP SENSOR, CLX-9201,UL10272,6 |
| Парткод: | JC39-01588A |
| Деталь: | GUIDE-PICKUP 2ND, CLX-9201,ABS,328.5,HF-0 |
| Парткод: | JC61-04717A |
| Деталь: | FRAME MAIN-PICKUP UPPER, CLX-9201,SEC |
| Парткод: | JC93-00504A |
| Деталь: | FRAME MAIN-PICKUP LOWER, CLX-9201,SEC |
| Парткод: | JC93-00503A |
| Деталь: | FRAME-MAIN PICK UP ROLLER, CLX-9201,0,EXP |
| Парткод: | JC93-00540A |
| Цена: | 700 ₽ |
| Деталь: | GEAR-PICKUP, CLX-9201,POM,0.8,31,NATURAL( |
| Парткод: | JC66-03281A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | ACTUATOR-EMPTY PICKUP, CLX-9201,POM,M90-4 |
| Парткод: | JC66-03199A |
| Деталь: | GEAR-M_PU JOINT, SCX-6345N/XRX,POM,0.7,21 |
| Парткод: | JC66-00943A |
| Деталь: | HOLDER-M_IDLE ONE WAY, SCX-6345N/XRX,POM, |
| Парткод: | JC61-01288A |
| Деталь: | GEAR-M_IDLE PU, SCX-6345N/XRX,POM,0.7,22, |
| Парткод: | JC66-00940A |
| Деталь: | CLUTCH-P_ONE WAY, SCX-6345N/XRX,STS304,0. |
| Парткод: | JC66-00977A |
| Деталь: | COUPLER-TORQUELIMITER, CLX-9350,WHITE,350 |
| Парткод: | JC67-00455A |
| Деталь: | SPRING-ES, STAINLESS-STS304,0.75,32.5,3.5 |
| Парткод: | 6107-001757 |
| Деталь: | LEVER-INPUT CST, CLX-9201,POM,52.9,28.7,M |
| Парткод: | JC66-03200A |
| Деталь: | HOLDER-RETARD, CLX-9201,POM,137,BLACK,M90 |
| Парткод: | JC61-04732A |
| Деталь: | DRIVE-M FUSER EXIT, SEC,OD30.5,NTR,PART,S |
| Парткод: | JC93-00449A |
| Деталь: | BRACKET-M DRIVE FUSER EXIT, SCX-8128NA,EG |
| Парткод: | JC61-04512A |
| Деталь: | GEAR-RDCN EXIT, CLX-9201NA,POM,0.8,1.0,41 |
| Парткод: | JC66-03108A |
| Деталь: | GEAR-M FUSER ONE WAY, SCX-8128NA,POM,0.5, |
| Парткод: | JC66-03141A |
| Деталь: | GEAR-HUB CLUTCH, POM,18.5,10.4,11.3,NW-02 |
| Парткод: | JC66-00340A |
| Цена: | 220 ₽ |
| Деталь: | GEAR-RDCN FUSER OUT, ML-2150,NYLON,1,25,8 |
| Парткод: | JC66-00417A |
| Цена: | 240 ₽ |
| Деталь: | GEAR-RDCN FUSER RELEASE, CLX-9201NA,POM,0 |
| Парткод: | JC66-03106A |
| Деталь: | GEAR-FUSER RELEASE, CLX-9201NA,POM,0.8,43 |
| Парткод: | JC66-03107A |
| Деталь: | MOTOR BLDC, 2000rpm,1200gfcm,24V,2.8A,150 |
| Парткод: | JC31-00123B |
| Цена: | 3 700 ₽ |
| Деталь: | DRIVE-MOTOR STEP, SEC,CLX-9201NA |
| Парткод: | JC93-00452A |
| Деталь: | OPE, SL-X3220RX |
| Парткод: | JC97-04718A |
| Деталь: | OPE-FRONT, SL-X3220RX,SEC |
| Парткод: | JC97-04723A |
| Деталь: | BRACKET-SUPPORT, CLX-9201,SECC,T1,W61,L10 |
| Парткод: | JC61-04567A |
| Деталь: | COVER-OPE BOTTOM, X3220,ABS,T 2.5,SPLIT B |
| Парткод: | JC63-05299A |
| Деталь: | LCD-CITARA, AVD-TT70WV-NN-005-A,Citara,80 |
| Парткод: | JC07-00028A |
| Деталь: | PBA OPE, X3220/K3250 |
| Парткод: | JC92-02835A |
| Деталь: | PBA-OPE KEY, CLX-9201/9251/9301,SEC,FR-1, |
| Парткод: | JC92-02435A |
| Деталь: | LCD-TSP, MX3,800480,7inch,RGB Color,-10 |
| Парткод: | JC07-00032A |
| Деталь: | BRACKET-LCD, X3220,EGI-SECC,0.8T,PRESS |
| Парткод: | JC61-07760A |
| Деталь: | KEY-M TEL, CLX-9201,ABS,7668.7,G32690 |
| Парткод: | JC64-00684A |
| Деталь: | COVER-OPE INNER, X3220,ABS,T 2.5,SPLIT BR |
| Парткод: | JC63-05300A |
| Деталь: | FRAME-FRONT MONO, K3250,SEC |
| Парткод: | JC93-01261A |
| Деталь: | FRAME-REAR MONO, K3250,SEC |
| Парткод: | JC93-01262A |
| Деталь: | FRAME MAIN-SWITCH OPEN, SCX-8128NA,SEC,WO |
| Парткод: | JC93-00466A |
| Деталь: | SPEAKER, 0.3W,8Ohm,81dB,400Hz |
| Парткод: | 3001-002207 |
| Деталь: | FRAME MAIN-FRONT LEVER, SCX-8128NA,SEC,WO |
| Парткод: | JC93-00470A |
| Деталь: | FRAME-FRONT MONO, SCX-8128NA,EGI-SECC,T0. |
| Парткод: | JC61-04844A |
| Деталь: | PBA-PAPER SIZE SENSOR, CLX-9352NA,SEC,FR1 |
| Парткод: | JC92-02622A |
| Деталь: | PLATE-GROUND CST, CLX-9350,STS304,0.2,GRO |
| Парткод: | JC61-03002A |
| Деталь: | FRAME-REAR MONO SUB, K3250,SEC |
| Парткод: | JC93-01271A |
| Деталь: | BRACKET-HINGE REAR, CLX-9201,SECC,T0.8,PR |
| Парткод: | JC61-04842A |
| Деталь: | PBA-WASTE SENSOR RX, CLX-9201,SEC,FR-4 |
| Парткод: | JC92-02471A |
| Деталь: | COVER-LEVER SLIDE, SCX-8128NA,HIPS,78.5,H |
| Парткод: | JC63-03419A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | CASSETTE-1ST, X3220,MX4N,300mm,55mm,Lifti |
| Парткод: | JC90-01140C |
| Деталь: | CASSETTE FRAME-1ST, X3220 |
| Парткод: | JC90-01187C |
| Деталь: | CASSETTE SUB-COVER, X3220 |
| Парткод: | JC90-01277B |
| Деталь: | SEAL-PAD CST, CLX-9201,CIGAL,BLK,0.7,47,1 |
| Парткод: | JC62-00946A |
| Деталь: | PLATE-KNOCK UP, CLX-9201,EGI-SECC,0.8T,36 |
| Парткод: | JC61-04767A |
| Деталь: | GEAR-M_PINION 24, SCX-6345N/XRX,POM,1,24, |
| Парткод: | JC66-01020A |
| Деталь: | INDICATOR-SIZE SIDE, CLX-9201,ABS,G72797, |
| Парткод: | JC64-00703A |
| Деталь: | GUIDE-LEFT, CLX-9201,HIPS,64,79.3,ICE-GRE |
| Парткод: | JC61-04718A |
| Деталь: | CASSETTE SUB-GUIDE REAR, X4300 |
| Парткод: | JC90-01291A |
| Деталь: | CASSETTE SUB-GUIDE FRONT, X4300 |
| Парткод: | JC90-01290A |
| Деталь: | CASSETTE-BRACKET LIFT, CLX-9201,SEC |
| Парткод: | JC90-01128A |
| Деталь: | CASSETTE SUB-LIFTING GEAR, CLX-9201 |
| Парткод: | JC90-01588A |
| Деталь: | LOCKER-CASSETTE 1ST, CLX-9201,POM,BLACK,7 |
| Парткод: | JC64-00715A |
| Деталь: | LEVER-LINK SIZE 1ST, CLX-9201,ABS,3,19.2, |
| Парткод: | JC66-03202A |
| Деталь: | PLATE-LEVER, CLX-9350,EGI-SECC,1.6T,73.6, |
| Парткод: | JC61-03206A |
| Деталь: | ROLLER-IDLE CST, CLX-9350,POM,OD10,L16.5, |
| Парткод: | JC61-03331A |
| Деталь: | RADF-FRAME MAIN, X3220,NON-MD |
| Парткод: | JC97-04732A |
| Деталь: | DADF-MOTOR, CLX-9201,SEC |
| Парткод: | JC97-03993A |
| Деталь: | RADF-FRICTION PAD, X3220,NON-MD |
| Парткод: | JC97-04733A |
| Деталь: | BELT-TIMING GEAR, 40S2M304,RUBBER,W4.0,L3 |
| Парткод: | 6602-003183 |
| Деталь: | CLUTCH-ELECTRONIC CLUTCH, SCX-8128NA,POM, |
| Парткод: | JC47-00033G |
| Деталь: | GEAR-EXIT, CLX-9201,POM,1.0,27,BLACK,29.0 |
| Парткод: | JC66-03261A |
| Деталь: | PULLEY-CLUTCH, CLX-9201,POM,6.02,19.864 |
| Парткод: | JC66-03175A |
| Деталь: | GEAR-IDLE_CLUTCH, CLX-9201,POM,1.0,22,BLA |
| Парткод: | JC66-03264A |
| Деталь: | GEAR-KNOB, CLX-9201,POM,0.8,20,ICE GREEN |
| Парткод: | JC66-03266A |
| Деталь: | GEAR-REDUCTION_KNOB, CLX-9201,POM,0.8,48, |
| Парткод: | JC66-03267A |
| Деталь: | PULLEY-FEED, CLX-9201,POM,BLACK,6,19.864 |
| Парткод: | JC66-03176A |
| Деталь: | MOTOR BLDC-TYPE1, 3002500rpm,DC 24V,25W, |
| Парткод: | JC31-00156A |
| Деталь: | SOLENOID-PICK UP, SCX-5100,DC 24V,80,36.5 |
| Парткод: | JC33-00007A |
| Деталь: | GEAR-REDUCTION, CLX-9201,POM,0.5/1.0,55/2 |
| Парткод: | JC66-03263A |
| Деталь: | GEAR-CAM_OUTER, CLX-9201,POM,1.0,28,BLACK |
| Парткод: | JC66-03260A |
| Деталь: | GEAR-CAM_INNER, CLX-9201,POM,1.0,28,BLACK |
| Парткод: | JC66-03259A |
| Деталь: | SPRING ETC-PICKUP, SCX-5100,SUS304-WPB,0. |
| Парткод: | JC61-00482A |
| Деталь: | GEAR-PICKUP_IDLE, CLX-9201,POM,1.0,20,BLA |
| Парткод: | JC66-03265A |
| Деталь: | BELT-TIMING GEAR, 40S2M258,RUBBER,W4.0,L2 |
| Парткод: | 6602-003186 |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | ROLLER ADF-EXIT, CLX-9201,EPDM,16 |
| Парткод: | JC66-03095A |
| Деталь: | ROLLER ADF-RUBBER-FEED, CLX-9201,EPDM,16 |
| Парткод: | JC66-03093A |
| Деталь: | ROLLER ADF-REGI, CLX-9201,EPDM,16 |
| Парткод: | JC66-03094A |
| Деталь: | ACTUATOR-EXIT, CLX-9201,PC,126.2 |
| Парткод: | JC66-03184A |
| Деталь: | BRUSH-ANTISTATIC, CLX-9201,SUS FIBER,0.2, |
| Парткод: | JC67-00562A |
| Деталь: | GUIDE-PICK UP, X3220,ABS,2.2,79.26,330,TX |
| Парткод: | JC61-07774A |
| Деталь: | GUIDE-WHITE_BAR, CLX-9201,PC,319.5,PATH |
| Парткод: | JC61-04584A |
| Деталь: | PAD-GUIDE_PICKUP, CLX-9201,PU,1.0,10,35 |
| Парткод: | JC69-02810A |
| Цена: | 290 ₽ |
| Деталь: | PLATEN-COVER GLASS LEFT WITH SH, X4300,SE |
| Парткод: | JC97-04599A |
| Деталь: | PLATEN-GLASS SCAN, X3220,NON-MD |
| Парткод: | JC97-04720A |
| Деталь: | COVER-GLASS RIGHT, X4300,ABS,SPLIT BROWN |
| Парткод: | JC63-04580A |
| Деталь: | GLASS TEMPERED-SCAN ADF, 337.831.1,4.0T |
| Парткод: | JC01-00101A |
| Деталь: | PLATEN-FR, X4300,SCANNER |
| Парткод: | JC97-04510A |
| Деталь: | PLATEN-SHIELD CCD, X4300,SCANNER |
| Парткод: | JC97-04502A |
| Деталь: | PLATEN-FRONT, X4300,SCANNER |
| Парткод: | JC97-04511A |
| Деталь: | PLATEN-LOWER, X4300,SCANNER |
| Парткод: | JC97-04515A |
| Деталь: | PLATEN-OPEN SENSOR, X4300,SCANNER |
| Парткод: | JC97-04516A |
| Деталь: | PBA-SCAN JOINT, X4300,SEC,FR-4,4L,12745m |
| Парткод: | JC92-02781A |
| Деталь: | BELT-TIMING GEAR, 1.5GT,Rubber(CR) |
| Парткод: | 6602-003616 |
| Деталь: | PULLEY-BELT, CLX-9350,POM,WHITE,8,36.305, |
| Парткод: | JC66-02257A |
| Деталь: | MOTOR STEP 1P, 17PM-K049-P6WS,HB,2,2.2V,4 |
| Парткод: | JC31-00158A |
| Деталь: | PLATEN-HINGE LEFT, NON-MD |
| Парткод: | JC97-04736A |
| Деталь: | PLATEN-HINGE RIGHT, NON-MD |
| Парткод: | JC97-04737A |
| Деталь: | PLATEN-REAR, X4300,SCANNER |
| Парткод: | JC97-04519A |
| Деталь: | STOPPER-GLASS, X4300,ABS,HF-0660I,BLACK,S |
| Парткод: | JC61-06254A |
| Деталь: | COVER-PBA, X4300,ABS,BLACK,HF-0660I |
| Парткод: | JC63-04680A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | PLATEN-LOWER, X4300,SCANNER |
| Парткод: | JC97-04515A |
| Деталь: | PLATEN-APS, X4300,SCANNER |
| Парткод: | JC97-04507A |
| Деталь: | PLATEN-LENS, X4300,SCANNER |
| Парткод: | JC97-04523A |
| Деталь: | FLAT CABLE-CCD IF, X4300,50P,560,AWM20624 |
| Парткод: | JC39-02119A |
| Деталь: | GUIDE-FFC CCD, X4300,HIPS,S-834,SPLIT GRA |
| Парткод: | JC61-06153A |
| Деталь: | WIRE-REAR, X4300,SUS304 |
| Парткод: | JC66-04157A |
| Деталь: | PLATEN-HR, X4300,SCANNER |
| Парткод: | JC97-04514A |
| Деталь: | PBA-WLED IF, CLX-9201,SEC,WLED IF,FR-4,1L |
| Парткод: | JC92-02728A |
| Деталь: | PULLEY-WIRE, X4300,PC,Black,NH-1035,Wire |
| Парткод: | JC66-04088A |
| Деталь: | PLATEN-PULLEY IDLER, X4300,SCANNER |
| Парткод: | JC97-04542A |
| Деталь: | WIRE-FRONT, X4300,SUS304 |
| Парткод: | JC66-04156A |
| Деталь: | GUIDE-HARNESS, X4300,ABS,HF-0660I,BLACK,G |
| Парткод: | JC61-06154A |
| Деталь: | GASKET-CONDUCTIVE, SCX-6345N,PUR FOAM,7mm |
| Парткод: | JC63-01173A |
| Деталь: | PLATE-SPRING BASE LENS, X4300,STS301,0.4, |
| Парткод: | JC61-06245A |
| Деталь: | PHOTO-INTERRUPTER, PHOTO IC,30mW,BULK |
| Парткод: | 0604-001453 |
| Деталь: | COVER-SIDE UPPER, K4350,ABS,SPLIT BROWN B |
| Парткод: | JC63-04573A |
| Деталь: | FAN-TYPE 6, 120mA,4.00mmH20,0.424m3/mi |
| Парткод: | JC31-00160C |
| Деталь: | COVER-SIDE MONO, X4300,ABS,SPLIT GRAY (GB |
| Парткод: | JC63-04576A |
| Деталь: | COVER-FRONT MP, ABS,SPLIT GRAY,HF-0660I |
| Парткод: | JC63-03356B |
| Деталь: | MP, X3220,MX4N,300mm,11mm,20,350g.cm,MD |
| Парткод: | JC90-01274B |
| Деталь: | GUIDE-DUPLEX UPPER, CLX-9201,ABS+PC,360.1 |
| Парткод: | JC61-04795A |
| Деталь: | COVER-SIDE EXIT, CLX-9201 |
| Парткод: | JC95-01509A |
| Деталь: | LINK-SIDE, X4300,POM,NATURAL (WHITE) |
| Парткод: | JC66-03220B |
| Деталь: | HANDLE-SIDE, X4300/K4350,ABS,780U,SPLIT B |
| Парткод: | JC64-00948A |
| Деталь: | COVER SIDE-DUPLEX, K3250 |
| Парткод: | JC95-02039A |
| Деталь: | LINK-D, CLX-9201,PC,133.8,BLACK |
| Парткод: | JC66-03235A |
| Деталь: | ROLLER IDLE-DUPLEX, CLX-9201,EPDM,SUM23,6 |
| Парткод: | JC66-03179A |
| Деталь: | COVER-SIDE DUPLEX LOWER, SCX-8128NA |
| Парткод: | JC95-01519A |
| Деталь: | LOCKER-SIDE, CLX-9201,POM,NATURAL,60.5,F2 |
| Парткод: | JC64-00710A |
| Деталь: | COVER-SIDE TAKE AWAY, CLX-9201 |
| Парткод: | JC95-01516A |
| Деталь: | COVER-HARNESS MONO, K4350,ABS,SPLIT GRAY, |
| Парткод: | JC63-03361B |
| Деталь: | COVER-HARNESS LOWER, X4300/K4350,HIPS,SPL |
| Парткод: | JC63-04574A |
| Деталь: | COVER-SIDE DUPLEX MOTOR, CLX-9201 |
| Парткод: | JC95-01510A |
| Деталь: | LOCKER-SIDE REAR, CLX-9201,POM,NATURAL,60 |
| Парткод: | JC64-00711A |
| Деталь: | BELT-TIMING GEAR, S2M328,RUB(CR),L328 |
| Парткод: | 6602-003299 |
| Деталь: | PULLEY-DUPLEX, CLX-9350,POM(M90-44),BLACK |
| Парткод: | JC66-02350A |
| Деталь: | GEAR-EXIT, CLX-9201,POM,1.0,16,WHITE,18.4 |
| Парткод: | JC66-03292A |
| Деталь: | COVER-SIDE LINK REAR, CLX-9201 |
| Парткод: | JC95-01518A |
| Деталь: | COVER SIDE-ROLLER TR, K3250 |
| Парткод: | JC95-02038A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | ACTUATOR-FUSER OUT, CLX-9201,MPPO,22.4,24 |
| Парткод: | JC66-03307A |
| Деталь: | ROLLER TR, K4350,19,NBR+ECO,310,7.70.2 |
| Парткод: | JC66-04205A |
| Деталь: | RADF-PLATEN, X3220,NON-MD |
| Парткод: | JC97-04730A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | ROLLER IDLE-IDLE SCF, SCX-6555N,POM,NW-02 |
| Парткод: | JC66-01022B |
| Деталь: | GROUND-HINGE_RIGHT, CLX-9201,C5210P,0.2,4 |
| Парткод: | JC63-03351A |
| Деталь: | ACTUATOR-SCAN, CLX-9201,PC,96.4,BLACK,ACT |
| Парткод: | JC66-03210A |
| Деталь: | GROUND-HINGE_FRAME, CLX-9201,C5210P,0.2,4 |
| Парткод: | JC63-03349A |
| Деталь: | SPRING-ES, SWP A,0.45,18.2,5.6,11.5,RIGHT |
| Парткод: | 6107-003277 |
| Деталь: | BRACKET-DUMMY PLATEN, EGI-SECC,1T,311,25, |
| Парткод: | JC61-05948A |
| Деталь: | MAGNET-SWITCH REED, X4300,BARIUM-FERRITE, |
| Парткод: | JC61-06349A |
| Деталь: | COVER-PLATEN, SCX-8120ND,HIPS,2.5T,SPLIT |
| Парткод: | JC63-04123A |
| Деталь: | EXIT, X4300 |
| Парткод: | JC90-01118B |
| Деталь: | BRACKET-REAR EXIT, CLX-9201,SECC,T1.0,48, |
| Парткод: | JC61-04690A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | BRUSH-EXIT, CLX-9201,SUS FIBER,347.5,16.9 |
| Парткод: | JC67-00563A |
| Деталь: | GEAR-EXIT, CLX-9350,POM,1.0,16,18.39 |
| Парткод: | JC66-02163A |
| Деталь: | SPRING TS, X4300,STS304,0.4,7.3,2.2 |
| Парткод: | JC61-07185A |
| Деталь: | ACTUATOR-BIN FULL EXIT, X4300/K4350,PC,NH |
| Парткод: | JC66-04339A |
| Деталь: | LEVER-ACTURATOR F_D FULL, CLX-9350,PC,HAZ |
| Парткод: | JC66-02218A |
| Деталь: | LEVER-ACT FULL EXIT, CLX-9350,PC,Black |
| Парткод: | JC66-02278A |
| Деталь: | SHAFT-ACTUATOR EXIT, K4350,STS430,187.0,3 |
| Парткод: | JC66-04753A |
| Деталь: | EXIT-GUIDE UPPER, CLX-9201 |
| Парткод: | JC90-01132A |
| Деталь: | EXIT-GUIDE LOWER, CLX-9201 |
| Парткод: | JC90-01133A |
Коды ошибок
11-2T11, 11-2T21, 11-2T31
11-2T41, 11-2T61
A1-1111, A1-1113
A1-1211, A1-1213
A1-2111, A1-2113
A1-5113, A1-5512
A1-5513, A1-5610
A2-1221, A2-1223
A2-1521, A2-1523
A2-2611, A2-2613
A3-3111, A3-3112
A3-3113, A3-3114
A3-3210, A3-3211, A3-3212
A3-3310, A3-3311, A3-3312
A3-3410, A3-3411, A3-3412
C1-1110, C1-111A
C1-1140, C1-1150, C1-1160
C1-1313, C1-1314
C1-1411
C1-1512
C3-1110
C3-1140, C3-1150, C3-1170
C3-1211
C3-1312
C3-1411
C3-1414
C3-1422
C3-1512
C5-3120
C6-1120
C6-1310
C6-1412
C7-1110, C7-1130
C7-1311
C8-1130
H1-1311, H1-1312, H1-1313
H1-1314, H1-1315
H1-1317, H1-1318
H1-1322
H1-1351, H1-1352, H1-1354
H1-1353
H1-1411, H1-1412
H1-1417, H1-1418
H1-1422
H1-1451, H1-1452, H1-1454
H1-1453
H1-5323
H1-5330
M1-1111, M1-1113
M1-1211, M2-1213
M1-1610, M1-1613
M1-3122
M1-3222
M1-4111
M1-4211
M1-5111, M1-5112
M1-5113, M1-5120
M1-5211, M1-5212, M1-5213
M1-5612, M1-5613
M2-1114, M2-1117
M2-1121, M2-1124, M2-1125
M2-1131, M2-1134, M2-1135
M2-1211
M2-1331, M2-1332, M2-1334
M2-2111, M2-2112, M2-2114
M3-1111, M3-1411
M3-1412, M3-1414
M3-2230, M2-2430
S1-1114
S1-2511
S1-5221
S2-1211, S2-2311, S2-3110
S2-331D, S2-331E
S2-3321, S2-3421
S2-4210
S2-4410
S3-3121
S3-3211
S4-3130
S5-3111
S6-3113, S6-3122
S6-3123
S6-3128
S6-3231
S6-3232
S6-3233
S6-3234
S6-3235, S6-3236
S7-1110
S7-1210
S7-2110
U1-2115
U1-2xxx
U2-1111, U2-1112, U2-1114
U2-1113
U2-6210
U3-3211, U3-3213, U3-3214
U3-3311, U3-3313, U3-3314
U3-3413, U3-3414
U3-3513, U3-3514
U3-3611, U3-3613
U3-3614, U3-3713
U3-4210
Описание
| Error code: | 11-2T11, 11-2T21, 11-2T31 |
| Description: | Paper mismatch Tray X Paper mismatch MPT |
| Causes: | Paper in tray is not matched to the machine paper setting. |
| Remedy: | 1) Check and change the paper setting of the corresponding tray properly. |
| Error code: | 11-2T41, 11-2T61 |
| Description: | Tray 1 Paper Mismatch Tray 2 Paper Mismatch Tray 3 Paper Mismatch Tray 4 Paper Mismatch MP Paper Mismatch |
| Causes: | Paper in tray is not matched to the machine paper setting. |
| Remedy: | 1) Check and change the paper setting of the corresponding tray properly. |
| Error code: | A1-1111, A1-1113 |
| Display: | Motor Failure: #A1-1111. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-1113. Turn off then on. Call for service if the problem persists. |
| Description: | Motor Failure: #A1-1111. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-1113. Turn off then on. Call for service if the problem persists. |
| Causes: | Regi/MP motor operation is abnormal. • A1–1111 : Regi/MP motor is stopped but machine recognizes it as operational. • A1–1113 : Regi/MP motor is operating but machine recognizes status as "Stopped". |
| Remedy: | 1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Open the side cover. Check if there are any foreign substances or paper around Regi./MP unit. 3) Remove the rear cover. 4) Check if the Regi/MP motor connector is connected correctly. 5) If the connection is OK, turn the machine on. Enter SVC mode. Select motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100–0000) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the motor(JC31-00123B). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board (JC44-00100C (220V) / JC44-00093C (110V)). - If the control signal is abnormal, replace the main board(JC92-02742A). b) If the motor is operational, • Check the Pin Num 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness. |
| Error code: | A1-1211, A1-1213 |
| Display: | Motor Failure: #A1-1211. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-1213. Turn off then on. Call for service if the problem persists. |
| Description: | Motor Failure: #A1-1211. Turn off then on. Call for service if the problem persists Motor Failure: #A1-1213. Turn off then on. Call for service if the problem persists |
| Causes: | Fuser motor operation is abnormal. • A1–1211 : Fuser motor is stopped but machine recognizes it as operational. • A1–1213 : Fuser motor is operating but recognizes status as "Stopped". |
| Remedy: | 1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Open the side cover. Check if there are any foreign substances or paper around fuser unit. 3) Remove the rear cover. 4) Check if the fuser motor connector is connected correctly. 5) If the connection is OK, turn the machine on. Enter SVC mode. Select motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100–0120) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the motor(JC31-00123B). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board (JC44-00100C (220V) / JC44-00093C (110V)). - If the control signal is abnormal, replace the main board(JC92-02742A). b) If the motor is operational, • Check the Pin Num 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness. |
| Error code: | A1-2111, A1-2113 |
| Display: | Motor Failure: #. Turn off then on. Call for service if the problem persists. |
| Description: | Motor Failure: #A1-2111. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-2113. Turn off then on. Call for service if the problem persists. |
| Causes: | OPC motor does not operate. / OPC motor is operational but machine recognizes status as stopped. |
| Remedy: | 1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Open the side cover. Check if there are any foreign substances or paper around drum drive unit. 3) Remove the rear cover 4) Check if the OPC motor connector is connected correctly. 5) If the connection is OK, turn the machine on. Enter the SVC mode. Select the yellow OPC motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100–0044) a) If the motor does not operates. i) Check the signal and power with the DVM. ii) If the checked result is normal, replace the BLDC motor(JC31-00123B). iii) If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board (JC44-00100C (220V) / JC44-00093C (110V)). - if the control signal is abnormal, replace the main board(JC92–02746A) b) If the motor is operational, check the Pin Num 8. i) If the value is abnormal, replace the main board. ii) If the value is normal, replace the harness. |
| Error code: | A1-5113, A1-5512 |
| Description: | Motor Failure: #A1-5113. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-5512. Turn off then on. Call for service if the problem persists. |
| Causes: | The motor related to toner supply has a problem. |
| Remedy: | 1) Open the front cover. If the toner pipe is blocked, open it. 2) Turn the machine off then on. If the error persists, check the following steps. 3) Enter the SVC mode. Select the toner supply motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 111-0030) 4) If the motor does not operate, measure the motor power with DVM. - Measure two points together. a) If 24V power is supplied, replace the toner supply motor(JC31-00123B). b) If 24V power is not supplied, check the SMPS and main board i) If 24V power is not generated, replace the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)). ii) If the control signal is abnormal, replace the main board(JC92–02746A). |
| Error code: | A1-5513, A1-5610 |
| Description: | Motor Failure: #A1-5513. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-5610. Turn off then on. Call for service if the problem persists. |
| Causes: | The motor related to toner supply has a problem. |
| Remedy: | 1) Open the front cover. If the toner pipe is blocked, open it. 2) Turn the machine off then on. If the error persists, check the following steps. 3) Enter the SVC mode. Select the toner supply motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 111-0030) 4) If the motor does not operate, measure the motor power with DVM. - Measure two points together. a) If 24V power is supplied, replace the toner supply motor(JC31-00123B). b) If 24V power is not supplied, check the SMPS and main board i) If 24V power is not generated, replace the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)). ii) If the control signal is abnormal, replace the main board(JC92–02746A). |
| Error code: | A2-1221, A2-1223 |
| Description: | Fan Failure: #A2–1211 / A2–1212 / A2–1221 / A2–1223. Turn off then on. Call for service if the problem persists |
| Causes: | SMPS or Fuser or Duplex or LSU fan is not operational. • SMPS fan error : A2–1211 / A2–1212 / A2–1221 / A2–1223 • Duplex fan error : A2–1521 / A2–1523 • Fuser fan error : A2–2310 / A2–2311 / A2–2321 / A2–2323 |
| Remedy: | 1) Turn the machine off. 2) Remove the rear cover. 3) Check if the corresponding fan connector is connected correctly. 4) If the connection is OK, Enter SVC mode and execute fan test. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 100-0260 : SMPS Fan Run • 109-0040 : Fuser Fan Run 5) If the fan is not operational, measure the fan power. (Red line) a) If 24V power is generated, replace the defective fan. • Fuser Fan : JC31–00161A • SMPS Fan : JC31–00160B b) If 24V power is not generated, • Measure the 24V power on the SMPS board. If the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)) is defective, replace it. • If the SMPS board is normal, replace the main board(JC92–02742A). 6) If the fan operation is normal but the error persists, a) Check the yellow line signal with DVM. (Refer to the image in step 5) b) Check fan operation as connected or disconnected. • If the Lock signal is 0V continually, check the harness. If the harness is OK, replace the main board. • If the signal value is different from the table above, replace the fan. |
| Error code: | A2-1521, A2-1523 |
| Description: | Fan Failure: #A2–1521 / A2–1523. Turn off then on. Call for service if the problem persists |
| Causes: | SMPS or Fuser or Duplex or LSU fan is not operational. • SMPS fan error : A2–1211 / A2–1212 / A2–1221 / A2–1223 • Duplex fan error : A2–1521 / A2–1523 • Fuser fan error : A2–2310 / A2–2311 / A2–2321 / A2–2323 |
| Remedy: | 1) Turn the machine off. 2) Remove the rear cover. 3) Check if the corresponding fan connector is connected correctly. 4) If the connection is OK, Enter SVC mode and execute fan test. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 100-0260 : SMPS Fan Run • 109-0040 : Fuser Fan Run 5) If the fan is not operational, measure the fan power. (Red line) a) If 24V power is generated, replace the defective fan. • Fuser Fan : JC31–00161A • SMPS Fan : JC31–00160B b) If 24V power is not generated, • Measure the 24V power on the SMPS board. If the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)) is defective, replace it. • If the SMPS board is normal, replace the main board(JC92–02742A). 6) If the fan operation is normal but the error persists, a) Check the yellow line signal with DVM. (Refer to the image in step 5) b) Check fan operation as connected or disconnected. • If the Lock signal is 0V continually, check the harness. If the harness is OK, replace the main board. • If the signal value is different from the table above, replace the fan. |
| Error code: | A2-2611, A2-2613 |
| Description: | Development Fan Failure: #A2-261x. Turn off then on. Call for service if the problem persists |
| Causes: | Fan does not operate or fan signal is abnormal. • SMSP fan error : A2–1221 / A2–1223 • Duplex fan error : A2–1521 / A2–1523 • Deve fan error : A2–2611 / A2–2613 |
| Remedy: | 1) Turn the machine off then on. If the problem persists, check the followings. 2) Check the connection of the corresponding fan and main board. 3) If the connection is OK, enter SVC mode. Execute the fan test. (Diagnostics > Engine Diagnostics > Engine Test Routines) a) If the fan is not operational, i) Check the power(24V). • If the power is abnormal, check the SMPS board. If the SMPS board is defective, replace it. • If the SMPS board is normal, replace the corresponding fan. • If the error persists after replacing the fan, replace the main board. b) If the fan is operational, i) Check the fan signal (3.3V) as connected or disconnected. • If the fan signal as disconnected is abnormal, replace the main board. • If the fan signal as connected is abnormal, replace the corresponding fan. |
| Error code: | A3-3111, A3-3112 |
| Display: | Sensor Failure: #. Turn off then on. Call for service if the problem persists. |
| Description: | Sensor Failure: #A3-3111. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3112. Turn off then on. Call for service if the problem persists |
| Causes: | The NC sensor in the fuser unit is defective. / The sensor signal is abnormal due to a defective harness. • A3–3111 : Center NC sensor is in short status. • A3–3112 : Center NC sensor is in open status. • A3–3113 : Side NC sensor is in short status. • A3–3114 : Side NC sensor is in open status. |
| Remedy: | 1) Enter SVC mode. Execute sensor test to check the sensor operation. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 109-0000 : Fuser Temperature A • 109-0010 : Fuser Temperature B 3) Measure the resistance value of the thermistor (1404-001453). If the measured value is out of 307KΩ~430KΩ @25℃, replace the thermistor. 4) Install the fuser unit after replacing the thermistor. 5) If the error persists, replace the fuser unit (JC91-01157A(220V) / JC91–01158A (110V)). 6) If the error persists after replacing fuser unit, replace the main board(JC92–02742A). |
| Error code: | A3-3113, A3-3114 |
| Display: | Sensor Failure: #. Turn off then on. Call for service if the problem persists. |
| Description: | Sensor Failure: #A3-3113. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3114. Turn off then on. Call for service if the problem persists |
| Causes: | The NC sensor in the fuser unit is defective. / The sensor signal is abnormal due to a defective harness. • A3–3111 : Center NC sensor is in short status. • A3–3112 : Center NC sensor is in open status. • A3–3113 : Side NC sensor is in short status. • A3–3114 : Side NC sensor is in open status. |
| Remedy: | 1) Enter SVC mode. Execute sensor test to check the sensor operation. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 109-0000 : Fuser Temperature A • 109-0010 : Fuser Temperature B 3) Measure the resistance value of the thermistor (1404-001453). If the measured value is out of 307KΩ~430KΩ @25℃, replace the thermistor. 4) Install the fuser unit after replacing the thermistor. 5) If the error persists, replace the fuser unit (JC91-01157A(220V) / JC91–01158A (110V)). 6) If the error persists after replacing fuser unit, replace the main board(JC92–02742A). |
| Error code: | A3-3210, A3-3211, A3-3212 |
| Display: | Sensor Failure: #. Turn off then on. Call for service if the problem persists. |
| Description: | Sensor Failure: #A3-3210. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3211. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3212. Turn off then on. Call for service if the problem persists |
| Causes: | Inner temperature sensor is defective. • A3–3210 : Inner temperature sensor value is abnormal. • A3–3211 : Inner temperature sensor is in short status. • A3–3212 : Inner temperature sensor is in open status. |
| Remedy: | 1) Open the side cover. Check the connection. • If the connection is OK, replace the photo sensor (1404-001417). 2) If the sensor is normal, replace the main board(JC92-02742A). |
| Error code: | A3-3310, A3-3311, A3-3312 |
| Display: | Sensor Failure: #A3-3310. Turn off then on. Call for service if the problem persists. Actuator Fan Failure #: Turn off then on. |
| Description: | Sensor Failure: #A3-3310. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3311. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3312. Turn off then on. Call for service if the problem persists |
| Causes: | Outer temperature/humidity sensor is defective. • A3–3310 / A3–3311 / A3–3312 : Temperature function is abnormal. • A3–3410 / A3–3411 / A3–3412 : Humidity function is abnormal. |
| Remedy: | 1) Remove the left cover. Unplug and reconnect the sensor harness. If the error persists, replace the sensor(JC93-00486A). 2) If the harness and sensor are normal, replace the main board (JC92-02742A). |
| Error code: | A3-3410, A3-3411, A3-3412 |
| Display: | Sensor Failure: #A3-3310. Turn off then on. Call for service if the problem persists. Actuator Fan Failure #: Turn off then on. |
| Description: | Sensor Failure: #A3-3410. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3411. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3412. Turn off then on. Call for service if the problem persists |
| Causes: | Outer temperature/humidity sensor is defective. • A3–3310 / A3–3311 / A3–3312 : Temperature function is abnormal. • A3–3410 / A3–3411 / A3–3412 : Humidity function is abnormal. |
| Remedy: | 1) Remove the left cover. Unplug and reconnect the sensor harness. If the error persists, replace the sensor(JC93-00486A). 2) If the harness and sensor are normal, replace the main board (JC92-02742A). |
| Error code: | C1-1110, C1-111A |
| Display: | C1-1110, C1-111A Toner error |
| Description: | Prepare new yellow toner cartridge. Shake toner cartridge and then install. Replace toner cartridge if the problem persists |
| Causes: | Toner remained is 5 ~ 30% of its life. |
| Remedy: | 1) Order new yellow toner cartridge because toner cartridge with level of “Low” will be exhausted soon. |
| Error code: | C1-1140, C1-1150, C1-1160 |
| Description: | End of life, Replace with new toner cartridge Replace with new toner cartridge |
| Causes: | The toner cartridge is at the end of its life. |
| Remedy: | 1) Open the front cover. 2) Remove the toner cartridge. 3) Install the new toner cartridge. 4) Close the front cover. |
| Error code: | C1-1313, C1-1314 |
| Display: | C1-1313, C1-1314 Errors |
| Description: | Shake toner cartridge and then install. Call for service if the problem persists Did not supply enough toner. Remove seal tape of toner cartridge or shake it. Call for service if the problem persists |
| Causes: | The toner supply is abnormal. |
| Remedy: | 1) Turn the machine off then on. 2) Open the front cover. 3) Remove the toner cartridge. Thoroughly roll the cartridge three or four times to distribute the toner evenly inside the cartridge. And reinstall the toner cartridge. 4) Try to print out the sample page more than 20 pages. 5) Check the toner cartridge. • Check if the toner cartridge is installed correctly. • Check if the toner seal is removed perfectly. • Check if the toner supply shutter between the toner cartridge and the imaging unit works normally. 6) Replace the toner cartridge. Print out the sample page. 7) Check the toner supply motor operation. • Check the signal and power with the DVM. • If the checked result is normal, replace the DC motor or the main drive unit. |
| Error code: | C1-1411 |
| Display: | Toner cartridge is not installed. Install it. |
| Description: | Toner cartridge is not installed. Install the cartridge |
| Causes: | The toner cartridge is not installed. / The machine can’t detect the toner cartridge. |
| Remedy: | 1) Turn the machine off then on. 2) Remove the toner cartridge. Thoroughly roll the cartridge five or six times to distribute the toner evenly inside the cartridge. And reinstall the toner cartridge. 3) Check if the CRUM contact area is contaminated. Clean it. |
| Error code: | C1-1512 |
| Display: | Toner cartridge is not compatible. Check users guide. |
| Description: | Toner cartridge is not compatible. Check users guide. |
| Causes: | Toner cartridge is not compatible. |
| Remedy: | 1) Print the supply information report. Check information of the toner cartridge. 2) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one. |
| Error code: | C3-1110 |
| Display: | Prepare IMG. Unit / Prepare new imaging unit Replace IMG. Unit / Replace with new imaging unit |
| Description: | The remaining imaging unit is less than 10% / The imaging unit is at the end of its life. |
| Causes: | Imaging unit has almost reached the end of its life. |
| Remedy: | These errors are for M3325/3825/4025. Check the life remaining of the imaging unit. If its life is at the end, turn the machine off and replace the imaging unit with new one. |
| Error code: | C3-1140, C3-1150, C3-1170 |
| Display: | C3-1140, C3-1150, C3-1170 Imaging unit errors |
| Description: | Replace with new imaging unit End of life, Replace with new imaging unit. |
| Causes: | Imaging unit is at the end of its life. |
| Remedy: | 1) Open the front cover. 2) Remove the imaging unit and replace it with new one. 3) Close the front cover. |
| Error code: | C3-1211 |
| Display: | Imaging Unit Failure:#C3-1211. Please turn off then on. |
| Description: | Imaging Unit Failure:#C3-1211. Please turn off then on. |
| Causes: | Sensor calibration error that detects the toner density for image stabilization control has occurred. |
| Remedy: | 1) Open the front cover and remove the waste toner container. 2) Remove the imaging unit. 3) If its life is at the end, replace the drum unit and developer with new one. |
| Error code: | C3-1312 |
| Display: | Imaging Unit Failure: #C3-1312. Install imaging unit again. |
| Description: | Imaging Unit Failure: #C3-1312. Install imaging unit again |
| Causes: | Toner supply is inefficient or abnormal. |
| Remedy: | 1) Turn the machine off. Open the front cover 2) Remove the toner cartridge. Shake the toner cartridge horizontally to distribute the toner evenly inside the cartridge. 3) If the problem persists, check the follows. a) Check if the Toner Supply Drive Unit(JC93–00436A) is defective. b) Check if the Toner Duct Drive Unit(JC93–00451A) is defective. 4) If the problem persists, replace the toner cartridge. 5) If the problem persists, replace the drum unit. |
| Error code: | C3-1411 |
| Display: | Imaging unit is not installed. Install the unit. |
| Description: | Imaging unit is not installed. Install the unit |
| Causes: | The imaging unit is not installed. / The machine can’t detect the imaging unit. |
| Remedy: | 1) Open the front cover. Check if the imaging unit is installed. 2) Remove and reinstall the imaging unit. 3) Check if the contact terminal is contaminated or broken. Clean the contact terminal. 4) Check if the CRUM harness is connected correctly. Reconnect it. 5) If the harness is defective, replace it. 6) If the problem persists, replace the imaging unit with new one. |
| Error code: | C3-1414 |
| Description: | Imaging Unit Failure: #C3-1414. Install imaging unit again |
| Causes: | The machine can’t read the charger resistance value. |
| Remedy: | 1) Turn the machine off then on. 2) Open the front cover and remove the waste toner container. 3) Remove the drum unit. 4) Check if the contact terminal is contaminated. Clean the contamination. 5) If the problem persists, replace the drum unit with new one. |
| Error code: | C3-1422 |
| Display: | Imaging unit is not installed. Install the unit. |
| Description: | Imaging unit requires chargers cleaning. Clean the unit. |
| Causes: | The imaging unit needs to clean. |
| Remedy: | 1) Open the front cover and remove the waste toner container. 2) Clean the drum unit by charger cleaner. 3) If its life is at the end, replace the drum unit and developer with new one. |
| Error code: | C3-1512 |
| Display: | Imaging unit is not compatible. Check user`s guide |
| Description: | Imaging unit is not compatible. Check the user guide |
| Causes: | Imaging unit is not compatible. |
| Remedy: | 1) Open the front cover. Remove the imaging unit. 2) Check if the label information of the imaging unit is same with the machine’s one. (ex. /SEE) 3) If label information is different from the machine or the imaging unit is not a samsung genuine, replace it with a new one. |
| Error code: | C5-3120 |
| Description: | Replace with new transfer roller |
| Causes: | The life of the transfer roller has expired. |
| Remedy: | 1) Turn the machine off. 2) Replace the transfer roller. 3) Turn the machine on. |
| Error code: | C6-1120 |
| Display: | Replace new Fuser unit |
| Description: | Replace with new fuser unit |
| Causes: | The life of the fuser unit has expired. |
| Remedy: | 1) Turn the machine off. 2) Replace the fuser unit(JC91-01157A (220V) /JC91-01158A (110V)). 3) Turn the machine on. |
| Error code: | C6-1310 |
| Display: | Fuser unit is not installed. Install it |
| Description: | Fuser unit is not installed. Install it. |
| Causes: | The fuser unit is not installed or fuser unit connector is not connected properly. |
| Remedy: | 1) Turn the machine off then on. 2) If the problem persists, turn the machine off again. 3) Open the side cover. Check if the fuser unit is installed. If not, install the fuser unit. 4) If the fuser unit is installed, remove it. 5) Check if the fuser draw connector (JC39–01677A) is broken or defective. 6) Install the fuser unit. 7) If the problem persists, replace the fuser unit(JC91-01157A (220V) /JC91-01158A (110V)). |
| Error code: | C6-1412 |
| Description: | Fuser unit is not compatible. Check the user guide. |
| Causes: | Fuser unit is not compatible |
| Remedy: | 1) Turn the machine off then on. 2) If the problem persists, turn the machine off. Remove the fuser unit. Check if the fuser unit is compatible with the machine. 3) If the fuser unit is not a samsung genuine, replace it with a new one. |
| Error code: | C7-1110, C7-1130 |
| Display: | Waste toner container is almost full. Order new one. Waste toner container is full. Replace it. |
| Description: | Waste toner container is almost full. Order new one. Waste toner container is full. Replace it. |
| Causes: | The life of the waste toner container expires soon or has expired. |
| Remedy: | 1) Open the front cover. 2) Remove the waste toner container. Install a new waste toner container. 3) Close the front cover. |
| Error code: | C7-1311 |
| Display: | Waste toner container is not installed. Install it. |
| Description: | Not Installed Waste tank |
| Causes: | The waste toner container is not installed |
| Remedy: | 1) Check if the waste toner container is installed properly. 2) Remove and reinstall the waste toner container. |
| Error code: | C8-1130 |
| Description: | Replace with new magenta developer unit |
| Causes: | The life of the developer unit has expired. |
| Remedy: | 1) Turn the machine off. 2) Open the front cover and remove the waste toner container. 3) Remove the imaging unit. 4) If the life of the developer unit has expired, replace the developer unit with new one. |
| Error code: | H1-1311, H1-1312, H1-1313 |
| Description: | Paper jam in Tray 3. |
| Causes: | Paper jam has occurred in tray3. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.) |
| Remedy: | 1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray3. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray3. 3) If this jam error occurs frequently, check the rollers below. a) Remove the tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit1. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit1. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit1. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit1(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A). |
| Error code: | H1-1314, H1-1315 |
| Description: | Paper jam in Tray 3. |
| Causes: | Paper jam has occurred in tray3. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.) |
| Remedy: | 1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray3. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray3. 3) If this jam error occurs frequently, check the rollers below. a) Remove the tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit1. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit1. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit1. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit1(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A). |
| Error code: | H1-1317, H1-1318 |
| Display: | Paper jam in Tray 3. |
| Description: | Paper jam in Tray 3. |
| Causes: | Paper jam has occurred in tray3. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.) |
| Remedy: | 1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray3. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray3. 3) If this jam error occurs frequently, check the rollers below. a) Remove the tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit1. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit1. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit1. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit1(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A). |
| Error code: | H1-1322 |
| Display: | Tray 3 cassette is pulled out. Insert it properly. |
| Description: | Tray 3 cassette is pulled out. Insert it properly. |
| Causes: | Tray 3 is pulled out or the auto size sensor connector is not connected or broken. |
| Remedy: | 1) Remove and insert tray3 correctly. 2) If the problem persists, remove tray3 and tray4. Look inside machine. 3) Check if the auto size sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the auto size sensor(JC93-00018A). 5) If the problem persists, replace the DCF board(JC92-02453A). |
| Error code: | H1-1351, H1-1352, H1-1354 |
| Display: | Paper is low in Tray 3. Load paper. Paper is empty in tray 3. Load paper. |
| Description: | Paper is low in Tray 3. Load paper. Paper is empty in Tray 3. Load paper. |
| Causes: | Paper in the tray is less than 10% of specification. / The photo sensor is defective. |
| Remedy: | 1) Remove tray3. Load the paper in tray3. 2) If paper is loaded but error message has not disappeared, check the following. a) Remove the DCF pick up unit1. b) Check if the photo sensor in the DCF pick up unit1 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. d) If the actuator(JC66-03199A) is defective, replace it. |
| Error code: | H1-1353 |
| Display: | Input System Failure #H1-1353 : Pull Tray 3 out and insert it. |
| Description: | Input System Failure #H1-1353 : Pull Tray 3 out and insert it. |
| Causes: | The paper is not fed from tray3. |
| Remedy: | 1) Remove and insert tray3 correctly. 2) Turn the machine off then on. 3) If the problem persists, turn the machine off. 4) Remove the Bracket Rear Cover after removing 5 screws. 5) Check if the connection between the DCF pick up drive and DCF board is correct. 6) If the connection is OK, replace the pick up drive unit(JC93-00442A). 7) If the problem persists, check the following. a) Remove the DCF pick up unit1. b) Check if the photo sensor in the DCF pick up unit1 is contaminated, clean it. c) If the photo sensor(0604-001393) is defective, replace it. |
| Error code: | H1-1411, H1-1412 |
| Description: | Paper jam in Tray 4. |
| Causes: | Paper jam has occurred in tray4. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.) |
| Remedy: | 1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray4. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray4. 3) If this jam error occurs frequently, check the rollers below. a) Remove tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit2. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit2. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit2. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit2(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A). |
| Error code: | H1-1417, H1-1418 |
| Display: | Paper jam in Tray 4. |
| Description: | Paper jam in Tray 4. |
| Causes: | Paper jam has occurred in tray4. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.) |
| Remedy: | 1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray4. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray4. 3) If this jam error occurs frequently, check the rollers below. a) Remove tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit2. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit2. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit2. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit2(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A). |
| Error code: | H1-1422 |
| Display: | Tray 4 cassette is pulled out. Insert it properly. |
| Description: | Tray 4 cassette is pulled out. Insert it properly. |
| Causes: | Tray 4 is pulled out or the auto size sensor connector is not connected or is broken. |
| Remedy: | 1) Remove and insert tray4 correctly. 2) If the problem persists, remove tray3 and tray4. Look inside machine. 3) Check if the auto size sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the auto size sensor(JC93-00018A). 5) If the problem persists, replace the DCF board(JC92-02453A). |
| Error code: | H1-1451, H1-1452, H1-1454 |
| Display: | Paper is low in Tray 4. Load paper. Paper is empty in tray 4. Load paper. |
| Description: | Paper is low in Tray 4. Load paper. Paper is empty in Tray 4. Load paper. |
| Causes: | Paper in tray4 is less than 10%. / The photo sensor is defective. |
| Remedy: | 1) Remove tray4. Load the paper in tray4. 2) If paper is loaded but error message has not disappeared, check the following. a) Remove the DCF pick up unit2. b) Check if the photo sensor in the DCF pick up unit2 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. d) If the actuator(JC66-03199A) is defective, replace it. |
| Error code: | H1-1453 |
| Display: | Input System Failure #H1-1453 : Pull Tray 4 out and insert it. |
| Description: | Input System Failure #H1-1453 : Pull Tray 4 out and insert it. |
| Causes: | The paper is not fed from tray4. |
| Remedy: | 1) Remove and insert tray4 correctly. 2) Turn the machine off then on. 3) If the problem persists, turn the machine off. 4) Remove the Bracket Rear Cover after removing 5 screws. 5) Check if the connection between the DCF pick up drive and DCF board is correct. 6) If the connection is OK, replace the pick up drive unit(JC93-00442A). 7) If the problem persists, check the following. a) Remove the DCF pick up unit2. b) Check if the photo sensor in the DCF pick up unit2 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. |
| Error code: | H1-5323 |
| Display: | Tray door is open. Close the door |
| Description: | Tray door is open. Close the door |
| Causes: | DCF Takeaway-Cover is open. / I/L-Switch harness or connector is defective. |
| Remedy: | 1) Open and close the DCF Take away-Cover correctly. 2) If the problem persists, check the following. a) Check if I/L-Switch(HARNESS-DCF COVER OPEN)(JC39–01696A) is not operating normally. If it is defective, replace it. b) If the I/L Switch is OK, replace the DCF board(JC92–02453A). |
| Error code: | H1-5330 |
| Display: | DCF Failure #H1-5330. Check internal DCF connection. |
| Description: | DCF Failure #H1-5330. Check internal DCF connection. |
| Causes: | A communication error between the optional tray and the main machine has occurred. |
| Remedy: | 1) Lift up and release the DCF unit from the machine. 2) Remove the Bracket Rear Cover after removing 5 screws. 3) Check if the interface connector is connected to the DCF board. If the interface connector(JC39–01690A) is defective, replace it. 4) If the problem persists, replace the DCF board. |
| Error code: | M1-1111, M1-1113 |
| Description: | Paper jam in tray 1. Please remove the paper |
| Causes: | Paper jam has occurred in tray1. |
| Remedy: | 1) Open the side cover and check if a foreign substance or paper is jammed inside the machine. 2) Remove tray1 and remove the jammed paper. 3) If this jam error occurs frequently, check the rollers of the pick up unit1. a) Remove tray1 and tray2. b) Check if the pick up/ forward/ separation rollers are assembled correctly. c) If the pick up/ forward/ separation rollers are worn out or contaminated, replace the defective roller. 4) If the problem persists, check the pickup unit1 and feed sensor. a) Check if the pickup unit1 and feed sensor operate correctly. b) Check if the pickup unit1 harness is connected to the main board correctly. c) Check if the connector of the Guide-feed assembly is connected correctly. d) Check if the harness of pickup unit and feed sensor are connected correctly. 5) If the problem persists, check the pickup unit1. a) Remove the pickup unit and check the actuator and photo-sensor. b) Push the pickup-lever and check if it operates correctly. 6) If the problem persists, replace the pickup drive unit or Pickup unit1. |
| Error code: | M1-1211, M2-1213 |
| Description: | Paper jam in tray 2. Please remove the paper |
| Causes: | Paper jam has occurred in tray2. |
| Remedy: | 1) Open the side cover and check if a foreign substance or paper is jammed inside the machine. 2) Remove tray2 and remove the jammed paper. 3) If this jam error occurs frequently, check the rollers of the pick up unit2. a) Remove tray1 and tray2. b) Check if the pick up/ separation/ forward rollers are assembled correctly. c) If the pick up/ separation/ forward rollers are worn out or contaminated, replace the defective roller. 4) If the problem persists, check the pick-up unit2. a) Check if the pre-feed sensor is connected correctly. If the sensor is defective, replace it. b) If there is any defective part in pick-up unit 2, replace it or pick up unit 2. 5) If the problem persists, replace the pickup drive unit 2. |
| Error code: | M1-1610, M1-1613 |
| Description: | Paper jam in MP Tray. |
| Causes: | Paper jam has occurred in MP tray. |
| Remedy: | 1) Open the side cover. Remove the jammed paper from the MP tray. 2) If this jam error occurs frequently, check the rollers of the MP unit. a) Check if MP pick up/ reverse/ forward rollers are assembled correctly. b) If the MP pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller. 3) If the problem persists, check if the MP solenoid operates correctly. a) Enter SVC mode. Execute MP solenoid test. b) If the MP solenoid operation is abnormal, check the harness connection of MP unit. c) If the harness has no defects, replace the MP solenoid. 4) If the problem persists, please check the followings. a) Enter SVC mode. Execute the regi sensor test. i) If the Regi sensor doesn’t work, check below. • Check the harness connection between Regi sensor and main board. • If the harness connection is OK, replace the Regi sensor. ii) If the Regi sensor works normally, check the Feed/MP drive unit at SVC mode. • Check the harness connection of the Feed/MP drive unit. • If the harness connection is OK, replace the Feed/MP drive unit. |
| Error code: | M1-3122 |
| Display: | Tray 1 cassette is pulled out. Insert it properly. |
| Description: | Tray 1 cassette is pulled out. Insert it properly. |
| Causes: | Tray 1 is pulled out or the auto size sensor connector is not connected or broken. |
| Remedy: | 1) Remove and insert Tray1 correctly. 2) If Tray1 is not locked or pulled out without holding the locking lever, remove Tray1. 3) Check if foreign substance or paper is inside the space between Tray1,2. If so, please remove it. 4) If the problem persists, check that the auto size sensor is connected properly. 5) If the problem persists, replace the main board(JC92–02452A). |
| Error code: | M1-3222 |
| Display: | Tray 2 cassette is pulled out. Insert it properly. |
| Description: | Tray 2 cassette is pulled out. Insert it properly. |
| Causes: | Tray 2 is pulled out or the auto size sensor connector is not connected or broken. |
| Remedy: | 1) Remove and insert Tray2 correctly. 2) If Tray2 is not locked or pulled out without holding the locking lever, remove Tray2. 3) Check if foreign substance or paper is inside the space between Tray1,2. If so, please remove it. 4) If the problem persists, check that the auto size sensor is connected properly. 5) If the problem persists, replace the main board(JC92–02452A). |
| Error code: | M1-4111 |
| Display: | Input System Failure #M1-4111 : Pull Tray 1 out and insert it. |
| Description: | Input System Failure #M1–4111 : Pull Tray 1 out and insert it. |
| Causes: | The paper is not fed from tray1. |
| Remedy: | 1) Remove tray1 and re-install it. 2) If the problem persists, turn the machine off then on. 3) Enter SVC mode. Execute pickup motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100-0370) 4) If the pick up motor operation is abnormal, turn the machine off. 5) Remove the rear cover. 6) Check if the connection between pickup drive unit1 and main board is secure. 7) If the connection is OK, replace the pickup drive unit(JC93-00442A). 8) If the problem persists, check the pickup unit1. a) Check if the photo sensor in the pickup unit1 is defective. b) If the sensor(0604–001393) is defective, replace it. |
| Error code: | M1-4211 |
| Display: | Input System Failure #M1-4211 : Pull Tray 2 out and insert it. |
| Description: | Input System Failure #M1-4211 : Pull Tray 2 out and insert it. |
| Causes: | The paper is not fed from tray2. |
| Remedy: | 1) Remove tray2 and re-install it. 2) If the problem persists, turn the machine off then on. 3) Enter SVC mode. Execute pickup motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100-0380) 4) If the pick up motor operation is abnormal, turn the machine off. 5) Remove the rear cover. 6) Check if the connection between pickup drive unit2 and main board is secure. 7) If the connection is OK, replace the pickup drive unit(JC93-00442A). 8) If the problem persists, check the pickup unit2. a) Check if the photo sensor in the pickup unit2 is defective. b) If the sensor(0604–001393) is defective, replace it. |
| Error code: | M1-5111, M1-5112 |
| Display: | Paper is low in Tray 1. Load paper. Paper is empty in Tray 1. Load paper. |
| Description: | Paper is low in Tray 1. Load paper. Paper is empty in Tray 1. Load paper. |
| Causes: | Paper in the tray1 is less than 10%. / The photo sensor is defective. |
| Remedy: | 1) Remove tray 1. Load paper in the tray. And insert tray 1. 2) If paper is loaded but error message has not disappeared, check the following: a) Turn the machine off. Open the Side Cover. b) Remove Pick-Up Unit1. c) If the photo sensor is contaminated, clean it. d) If the photo sensor is defective, replace it(0604–001393). e) If the actuator is defective, replace it(JC66-03199A). |
| Error code: | M1-5113, M1-5120 |
| Description: | Paper is low in Tray 1. Load paper. Paper is empty in Tray 1. Load paper. |
| Causes: | Paper in the tray1 is less than 10%. / The photo sensor is defective. |
| Remedy: | 1) Remove tray 1. Load paper in the tray. And insert tray 1. 2) If paper is loaded but error message has not disappeared, check the following: a) Turn the machine off. Open the Side Cover. b) Remove Pick-Up Unit1. c) If the photo sensor is contaminated, clean it. d) If the photo sensor is defective, replace it(0604–001393). e) If the actuator is defective, replace it(JC66-03199A). |
| Error code: | M1-5211, M1-5212, M1-5213 |
| Description: | Paper is low in Tray 2. Load paper. Paper is empty in Tray 2. Load paper. |
| Causes: | Paper in the tray is less than 10% of specification. / The photo sensor is defective. |
| Remedy: | 1) Remove tray 2. Load paper in the tray, and insert the tray 2. 2) If paper is loaded but error message has not disappeared, check the following : a) Turn the machine off. Open the Side Cover. b) Remove Pick-Up Unit2. c) If the photo sensor is contaminated, clean it. d) If the photo sensor is defective, replace it. e) If the actuator is defective, replace it. |
| Error code: | M1-5612, M1-5613 |
| Description: | Paper is empty in MP Tray. Load paper. |
| Causes: | Paper in the MP tray is less than 10%. / The photo sensor is defective. |
| Remedy: | 1) Load the paper in the MP tray. 2) If paper is loaded but error message has not disappeared, check the following : a) If the photo sensor is contaminated, clean it. b) If the photo sensor is defective, replace it. c) If the actuator is defective, replace it. |
| Error code: | M2-1114, M2-1117 |
| Description: | Paper jam inside of machine Paper jam at the bottom of duplex path |
| Causes: | Paper jam has occurred inside the machine. |
| Remedy: | • M2–1114 : The paper has not left from the feed sensor within the specified time. • M2-1117 : The paper passed duplex path has not reached the feed sensor within the specified time. 1) Open the side cover. Remove the jammed paper. 2) If jammed paper occurs continually, check the following. a) Enter SVC mode. Execute the feed 1 sensor test. b) Check connection between the feed 1 sensor and main board. c) If the connection is OK, replace the feed 1 sensor. d) If the feed 1 sensor is normal, check the feed motor. e) Execute feed motor test. f) Check if the feed motor cable is connected correctly. g) If the connection is OK, replace the feed/MP drive unit. |
| Error code: | M2-1121, M2-1124, M2-1125 |
| Description: | Paper jam in tray 1. Please remove the paper Paper jam in tray 2. Please remove the paper Paper jam inside of machine. Please remove the paper |
| Causes: | Paper jam has occurred inside the machine. • M2–1121 : The paper is detected by feed 1 sensor. • M2–1124 : The leading edge of the paper has not reached the feed 1 sensor within the specified time. • M2-1125 : The paper has not left from the feed 1 sensor within the specified time. |
| Remedy: | 1) Open the side cover. Remove the jammed paper. 2) If jammed paper occurs continually, check the following. a) Enter SVC mode. Execute the feed 1 sensor test. b) Check connection between the feed 1 sensor and main board. c) If the connection is OK, replace the feed 1 sensor. d) If the feed 1 sensor is normal, check the feed motor. e) Execute feed motor test. f) Check if the feed motor cable is connected correctly. g) If the connection is OK, replace the feed/MP drive unit. |
| Error code: | M2-1131, M2-1134, M2-1135 |
| Description: | Paper jam in tray 2. Please remove the paper Paper jam in tray 1. Please remove the paper |
| Causes: | Paper jam has occurred inside the machine. • M2–1131 : The paper is detected by feed 2 sensor. • M2–1134 : The leading edge of the paper has not reached the feed 2 sensor within the specified time. • M2-1135 : The paper has not left from the feed 2 sensor within the specified time. |
| Remedy: | 1) Open the side cover. Remove the jammed paper. 2) If jammed paper occurs continually, check the following. a) Enter SVC mode. Execute the feed 2 sensor test. b) Check connection between the feed 2 sensor and main board. c) If the connection is OK, replace the feed 2 sensor. d) If the feed 2 sensor is normal, check the feed motor. e) Execute feed motor test. f) Check if the feed motor cable is connected correctly. g) If the connection is OK, replace the feed/MP drive unit. |
| Error code: | M2-1211 |
| Display: | SMART PANEL: |
| Description: | Paper jam inside of machine. Please remove the paper |
| Causes: | Paper jam has occurred inside the machine. (Regi. roller drive is defective / Regi. sensor is defective.) |
| Remedy: | 1) Open the side cover. Remove the jammed paper. 2) If jammed paper occurs continually, check the following. a) Enter SVC mode. Execute Regi. motor test. If the motor operation is normal, go to step d). b) Remove the rear cover. Check if the Regi/MP motor cable is connected correctly. c) If the connection is OK, replace the Regi./MP drive unit. d) If the motor operation is normal, check the regi. sensor. e) If the sensor operation is abnormal, check the harness. f) If the connection is OK, replace the regi. sensor. |
| Error code: | M2-1331, M2-1332, M2-1334 |
| Description: | Paper jam inside of machine. Please remove the paper Check whether the pieces of paper remain in the paper path Paper jam at the top of duplex path. Please remove the paper |
| Causes: | Paper jam has occurred inside the machine. |
| Remedy: | 1) Open the side cover. Remove jammed paper. 2) If the problem persists, check the following: a) Check the Regi sensor harness. If the harness is normal, replace the Regi. sensor. b) Check the sensors in the Side Unit. If the harness is normal, replace the defective sensor. |
| Error code: | M2-2111, M2-2112, M2-2114 |
| Description: | Paper jam inside of machine. Please remove the paper Check whether the pieces of paper remain in the paper path Paper jam at the top of duplex path. Please remove the paper |
| Causes: | Paper jam has occurred inside the machine. |
| Remedy: | 1) Open the side cover. Remove jammed paper. 2) If the problem persists, check the following: a) Check the Regi sensor harness. If the harness is normal, replace the Regi. sensor. b) Check the sensors in the Side Unit. If the harness is normal, replace the defective sensor. |
| Error code: | M3-1111, M3-1411 |
| Description: | Paper jam in exit area. Please remove the paper Check whether the pieces of paper remain in the paper path |
| Causes: | Paper jam has occurred around the fuser unit.(Job separator connection is defective. / Actuator-Exit is defective.) |
| Remedy: | 1) Open the side cover. Remove the jammed paper. 2) If the problem persists, check the following: a) Open the side cover. Check if the connector is connected properly. b) Remove the JOB-SEPARATOR. Check if the photo sensor is assembled correctly. c) Check if ACTUATOR-EXIT is assembled correctly. If the ACTUATOR-EXIT is deformed or broken, replace it. d) If the photo sensor is defective, replace it. |
| Error code: | M3-1412, M3-1414 |
| Description: | Paper jam in exit area. Please remove the paper Check whether the pieces of paper remain in the paper path |
| Causes: | Paper jam has occurred around the fuser unit.(Job separator connection is defective. / Actuator-Exit is defective.) |
| Remedy: | 1) Open the side cover. Remove the jammed paper. 2) If the problem persists, check the following: a) Open the side cover. Check if the connector is connected properly. b) Remove the JOB-SEPARATOR. Check if the photo sensor is assembled correctly. c) Check if ACTUATOR-EXIT is assembled correctly. If the ACTUATOR-EXIT is deformed or broken, replace it. d) If the photo sensor is defective, replace it. |
| Error code: | M3-2230, M2-2430 |
| Description: | Output tray is full. Remove printed media. |
| Causes: | There is too much paper in output bin tray or inner tray. • M3-2230 : There is too much paper in output bin tray. • M3-2430 : There is too much paper in inner tray. |
| Remedy: | 1) Remove the paper from output bin tray or inner tray. 2) If this error occurs continually, check the following. a) Check if the bin-full sensor and actuator is assembled correctly. b) Check if the bin-full sensor is defective. |
| Error code: | S1-1114 |
| Display: | Video System Failure #S1-1114: Turn off then on. |
| Description: | Video System Failure #S1-1114: Turn off then on. |
| Causes: | CPU fan is not working |
| Remedy: | 1) Turn the machine off. 2) Wait until the machine is cool. And then turn the machine on. 3) If the problem persists, turn the machine off again. 4) Remove the rear cover. 5) Replace the main board(JC92-02746A). NOTE Insert the MSOK to the new main board. 6) Assemble the rear cover. Turn the machine on. |
| Error code: | S1-2511 |
| Description: | Error: #S1-2511 / MSOK System Failure: #S1-2511.Call for service |
| Causes: | MSOK is not installed properly. / MSOK is defective. |
| Remedy: | 1) Turn the machine off then on. If the problem persists, check the followings. 2) Check if the MSOK is inserted correctly. Remove and reinstall it. 3) If the problem persists, replace the main board. |
| Error code: | S1-5221 |
| Display: | Wireless Network Error |
| Description: | The communication error between the main board and the wireless board has occurred. |
| Causes: | Communication Error with wireless NIC has occurred. |
| Remedy: | Check if the connection between the main board and the wireless board is normal. If the connection is OK, replace the part in this order. (Flat cable -> Wireless board -> Main board) |
| Error code: | S2-1211, S2-2311, S2-3110 |
| Description: | Engine System Failure: #S2-1211. Turn off then on Engine System Failure: #S2-2311. Turn off then on Engine System Failure: #S2-3110. Turn off then on |
| Causes: | The main board is defective. • Power chip error • EEPROM detection error • Communication error |
| Remedy: | 1) Turn the machine off then on. 2) If the problem persists, turn the machine off again. 3) Replace the main board(JC92-02742A). 4) Turn the machine on. |
| Error code: | S2-331D, S2-331E |
| Description: | Wait delay time for lower fixing temperature… The temperature of this machine is too low. Please wait for a while to warm up Supplying and mixing toner to developer unit. Please wait... Calibrating image density. Please wait... |
| Causes: | These error show the engine status. |
| Remedy: | 1) Wait until error will be disappeared. |
| Error code: | S2-3321, S2-3421 |
| Description: | Wait delay time for lower fixing temperature… The temperature of this machine is too low. Please wait for a while to warm up Supplying and mixing toner to developer unit. Please wait... Calibrating image density. Please wait... |
| Causes: | These error show the engine status. |
| Remedy: | 1) Wait until error will be disappeared. |
| Error code: | S2-4210 |
| Display: | Front door is open. Close it. |
| Description: | Front door is open. Close it. |
| Causes: | Front cover or Side cover is opened. |
| Remedy: | 1) Close the front cover correctly. 2) Check if the cover open sensor connector is connected properly. Reconnect it. 3) If the sensor is defective, replace it. |
| Error code: | S2-4410 |
| Display: | Right door is open. Close it. |
| Description: | Right door is open. Close it. |
| Causes: | Front cover or Side cover is opened. |
| Remedy: | 1) Close the side cover correctly. 2) Check if the cover open sensor connector is connected properly. Reconnect it. 3) If the sensor is defective, replace it. |
| Error code: | S3-3121 |
| Display: | Scanner Locked |
| Description: | CIS unit in the scanner does not move. |
| Causes: | Scanner lock error has occurred. CIS does not move. |
| Remedy: | 1) Check if the CIS unit moves when turning the machine off then on. 2) Check if the CIS cable is connected correctly. Reconnect it. 3) If the CIS unit is defective, replace it. 4) Check if there is any defective part in the scanner. Find and replace it. 5) If the problem persists, replace the main board. |
| Error code: | S3-3211 |
| Display: | Scan System Failure #S3-3211: Turn off then on. |
| Description: | Scan System Failure #S3-3211: Turn off then on. |
| Causes: | ADF is not connected or communication error occurs with CIP6 board. |
| Remedy: | 1) Turn the machine off then on. If the problem persists, check the following: 2) Turn the machine off again. 3) Remove the scan rear cover. Check if the connector on scan joint board is connected correctly. 4) Remove the ADF rear cover. Check if the connector on ADF board is connected correctly. 5) If the connection is OK, replace the ADF board. |
| Error code: | S4-3130 |
| Description: | There has been a problem with fax modem card. Install again. Call for service if the problem persists |
| Causes: | Fax card is not installed properly. / Fax card is defective. |
| Remedy: | 1) Remove and reinstall the fax card. 2) If the fax card is defective, replace it. |
| Error code: | S5-3111 |
| Display: | UI System Failure #S5-3111:Turn off then on. |
| Description: | UI System Failure #S5-3111:Turn off then on. |
| Causes: | Main board has critical problem which make its lockup or USB connection between main board and OPE has some problem. |
| Remedy: | 1) Turn off and turn on. And check if the problem disappears. a) If yes, go to step 2)-a). b) If no, go to step 2)-b). 2) Check the following procedure. a) Print the Error Information Report. . Service Mode - General - Print Reports - Error Information . Check the error code which is printed on the report. - If S5-3111 has occurred, go to step 4). - If S5-3112 has occurred, go to step 5)-c). - If S5-3113 has occurred, go to step 5)-d). b) Enter into System Recovery Mode. . How to enter System Recovery Mode : Turn on the machine with side cover open and power button on OPE is pressed state. . Check if entering System Recovery Mode is possible or not. - If entering System Recovery Mode is successful, go to step 3). - If entering System Recovery Mode fails, go to step 5)-d). 3) Execute the System Recovery. • Insert USB memory stick which has recovery one rom and execute recovery(HDD format). • Check if the problem disappears after system recovery(format complete). - If yes, go to step 4). - If no, go to step 5)-c). 4) Execute the firmware update. • Check if the problem disappears after one rom update. - If the problem disappears, go to step 5)-a). - If the problem happens sometimes, go to step 5)-b). 5) Check the following procedure. a) No more action is required because machine is recovered from S5-3111 error state. Please monitor the machine if S5-3111 happens again. b) Detailed analysis is required. Please capture the log and send it to development team in HQ. c) It seems that HDD or main board has some problem. Please replace HDD or main board with new one and check if the problem disappears. d) It seems that there is some critical issue in the USB connection between main board and OPE. Please try below steps. i) If WiFi module is installed, replace WiFi module with new one. ii) Check USB cable state between main board and OPE. iii) Replace the main board with new one. iv) Replace the OPE board with new one. |
| Error code: | S6-3113, S6-3122 |
| Description: | Network Failure: #S6-3113. Turn off then on. Call for service if the problem persists Network cable is disconnected. Check it. |
| Causes: | Network PHY chip is defective./ Network cable is disconnected. |
| Remedy: | 1) Check if the green LED of the network port is on. 2) If not, unplug and reconnect the network cable. 3) If the problem persists, replace the main board. |
| Error code: | S6-3123 |
| Display: | This IP address conflicts with that of other system. Check it. |
| Description: | This IP address conflicts with that of other system. Check it. |
| Causes: | Network has some problem. (IP address conflicts with that of other system. / Communication error / There is no response when checking the ping test.) |
| Remedy: | Change the machine’s IP address. • Execute the Samsung Easy Printer Manager program. (Device setting > Network > IP address). Change the IP address. • In case of DHCP or Bootp, reboot the machine to receive a new IP address. |
| Error code: | S6-3128 |
| Display: | 802.1x authentication failed. Please Contact the System Administrator |
| Description: | There is no response when checking the ping test. ID or Password is incorrect. |
| Causes: | Network error. ( A authenticator(eg switch) rejected authentication. / There is no response when checking the ping test.) |
| Remedy: | 1) Change the IP adredd (Machine Setup > Network Setting > Login > TCP/IP > Select the network protocol > IP Setting 2) Inut the Network Login ID and Password correctly. |
| Error code: | S6-3231 |
| Description: | Can not find a wireless network. Please check the wireless environment |
| Causes: | The machine can not find the SSID(Service Set Identifier). |
| Remedy: | 1) Check the setting-up for wireless network. |
| Error code: | S6-3232 |
| Description: | Wireless security settings are incorrect. Please change the settings |
| Causes: | Wireless security settings like a WEP/WPA/WPA2 are incorrect. |
| Remedy: | 1) Turn the machine and AP off then on. 2) Change the wireless network settings. |
| Error code: | S6-3233 |
| Description: | Not connected from the wireless AP. If you do not reconnect automatically, check the wireless settings |
| Causes: | Wireless BSSID value is 0 or wireless module is disconnected. |
| Remedy: | 1) Turn the machine and AP off then on. 2) Change the wireless network settings. |
| Error code: | S6-3234 |
| Description: | Failed connection to WPS. Try again or set up other wireless connection |
| Causes: | WPS connection to AP is failed. |
| Remedy: | 1) Retry the connection with WPS button. |
| Error code: | S6-3235, S6-3236 |
| Description: | Network Failure: #S6-3210. Turn off then on. Call for service if the problem persists. |
| Causes: | Wireless network has some problem. |
| Remedy: | 1) Turn the machine off then on. 2) Check the wireless network setting. If the setting in printer and AP device is abnormal, change it and retry the job. 3) Check if the connection between the main board and WLAN PBA is normal. Reconnect the harness. 4) If the harness connection is OK, replace the WLAN PBA. |
| Error code: | S7-1110 |
| Display: | Failure: #S7-1110. Turn off then on |
| Description: | Engine System Failure: #S7-1110. Turn off then on |
| Causes: | 24V power is abnormal. |
| Remedy: | 1) Check the 24V pin on SMPS board. If it is abnormal, replace the SMPS board. 2) Check the related cable. 3) If the SMPS is normal, replace the main board. |
| Error code: | S7-1210 |
| Display: | Failure: #S7-1210. Turn off then on |
| Description: | Engine System Failure: #S7-1110. Turn off then on |
| Causes: | 5V power is abnormal. |
| Remedy: | 1) Check the 5V pin on SMPS board. If it is abnormal, replace the SMPS board. 2) Check the related cable. 3) If the SMPS is normal, replace the main board. |
| Error code: | S7-2110 |
| Display: | Fuser Failure: #S7-2110. Turn off then on |
| Description: | Fuser Failure: #S7-2110. Turn off then on |
| Causes: | Heater control relay is abnormal. |
| Remedy: | 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) If the problem persists, replace the Fuser unit(110V : JC91-01158A, 220V : JC91-01157A). |
| Error code: | U1-2115 |
| Display: | Fuser Unit Failure: #U1-2115. Turn off then on. |
| Description: | Fuser Unit Failure: #U1-2115. Turn off then on. |
| Causes: | The pressure control unit(Cam unit)of the fuser is abnormal. |
| Remedy: | 1) Turn the machine off then open the side cover. 2) Remove and re-install the fuser unit, then turn the machine on. 3) If the problem persists, check the following : a) When the side-cover closes, check if the operation sound of the pressure control unit occurs. b) Check if the parts of the pressure control unit are abnormal. - Check if the shape of the CAM-REAR(JC66-03299A)) is broken. - Check if there are abnormal parts of the pressure control unit. c) Check if the fuser-motor is abnormal via SVC mode. 4) If the problem persists, replace the Fuser unit(110V : JC91-01158A, 220V : JC91-01157A). 5) If the problem persists, replace the pressure control unit or cam-motor or Main board(JC92-02742A). |
| Error code: | U1-2xxx |
| Description: | Fuser Unit Failure: #U1-2xxx Turn off then on |
| Causes: | The thermistor can’t measure temperature. The hear-roller will not heat-up. / Temperature of the fuser increases abnormally. |
| Remedy: | 1) Remove the fuser unit. After opening the jam cover, check if jammed or wrapped paper is in the fuser unit. 2) Re-install the fuser unit, then turn the machine on. 3) If the problem persists, check the following : a) Check if the Halogen lamp (110V : 4713-001630 / 220V : 4713–001631) is broken or disconnected. b) Check if the AC connection of the Halogen lamp is disconnected or contaminated. c) Check if the thermostat(4712-001098) is disconnected. d) Check if the non-contact type thermistor(1404–001453)is broken. 4) If the problem persists, replace the Fuser unit(110V : JC91-01158A, 220V : JC91-01157A). 5) If the problem persists, replace the Main board(JC92-02742A) or FDB board(110V : JC44-00210A, 220V : JC44-00211A), SMPS(110V : JC44-00093C, 220V : JC44-00100C) |
| Error code: | U2-1111, U2-1112, U2-1114 |
| Description: | LSU Failure: #U2-111x.Turn off then on. Call for service if the problem persists |
| Causes: | LSU motor does not operate or it operates abnormally. Motor ready signal is abnormal. |
| Remedy: | 1) Turn the machine off then on. Check for the LSU motor operation sound during warm-up. 2) Print a demo page to check that the machine operates normally. 3) If the problem persists, check the following : a) If the LSU motor makes a sound, i) Enter SVC mode to check the LSU motor ready signal. ( Diagnostics > Engine Diagnostics > Engine Test Routines) ii) Select gLSU Motor1 Run Readyh. iii) Press eStartf button. Check that the status has changed to eExecuting - Low - Highf. iv) If the status has not changed, the motor ready signal is abnormal. Replace the LSU. b) If the LSU motor does not makes a sound, i) Turn the machine off and open the side cover. Unplug and reconnect the LSU cable. Check that the LSU motor make a sound after turning the machine on. ii) Turn the machine off and remove the rear cover. Unplug and reconnect the LSU cable on main board. Check that the LSU motor make a sound after turning the machine on. iii) If the LSU cable is defective, replace it. Check that the LSU motor make a sound after turning the machine on. iv) If the problem persists, replace the LSU. |
| Error code: | U2-1113 |
| Display: | Error #U2-1113 Turn off then on. |
| Description: | LSU Motor does not work normally. |
| Causes: | LSU Hsync signal can not be detected correctly. LSU Hsync signal is abnormal. |
| Remedy: | 1) Execute the LSU motor test in EDC mode. Check LSU motor operation sound. 2) If there is no sound, remove the right cover. Check if the LSU harness is connected on the main board properly. (picture-1) 3) If it is OK, remove the top cover. Check if the LSU harness is connected on LSU board properly. (picture- 2,3) 4) Check if the LSU harness is defective. (picture-4) 5) Reconnect the LSU harness and then execute the LSU motor test again. 6) If the problem persists, replace the LSU(JC97-04065A). 7) If the problem persists after replacing LSU, replace the main board. |
| Error code: | U2-6210 |
| Description: | LSU Failure: #U1-6210. Turn off then on. Call for service if the problem persists |
| Causes: | LSU is not installed normally. |
| Remedy: | 1) Turn the machine off and open the side cover. Unplug and reconnect the LSU cable. Print a demo page to check that the machine operates normally. 2) Turn the machine off and open the side cover. Unplug and reconnect the LSU cable on main board. Print a demo page to check that the machine operates normally. 3) If the LSU cable is defective, replace it. Check that the LSU motor makes a sound after turning the machine on. 4) If the problem persists, replace the LSU. |
| Error code: | U3-3211, U3-3213, U3-3214 |
| Display: | U3-3211, U3-3213, U3-3214, U3-3311, U3-3313, U3-3314 Original paper jam / Original paper jam inside of scanner. Remove jam |
| Description: | Original paper jam inside of scanner |
| Causes: | Jam has occurred inside the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the Regi. sensor and Regi actuator. Push and release the regi actuator. Check if the pick up module returns the original position. If the sensor is defective, replace it(0604–001393). 3) If the regi sensor is OK, check the scan 1 sensor and reflect film. • If the scan 1 sensor is defective, replace it(0604–001381). • If the reflect film is contaminated, clean it. |
| Error code: | U3-3311, U3-3313, U3-3314 |
| Display: | U3-3211, U3-3213, U3-3214, U3-3311, U3-3313, U3-3314 Original paper jam / Original paper jam inside of scanner. Remove jam |
| Description: | Original paper jam inside of scanner |
| Causes: | Jam has occurred inside the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the Regi. sensor and Regi actuator. Push and release the regi actuator. Check if the pick up module returns the original position. If the sensor is defective, replace it(0604–001393). 3) If the regi sensor is OK, check the scan 1 sensor and reflect film. • If the scan 1 sensor is defective, replace it(0604–001381). • If the reflect film is contaminated, clean it. |
| Error code: | U3-3413, U3-3414 |
| Description: | Original paper jam inside of scanner. |
| Causes: | Jam has occurred inside the RADF unit. |
| Remedy: | 1) Open the RADF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the following: a) Check if the Regi. actuator operates normally. b) Check if the Regi. sensor cable is connected correctly. c) If the connection is OK, replace the Regi. sensor. |
| Error code: | U3-3513, U3-3514 |
| Display: | Original paper jam inside the scanner |
| Description: | Original paper jam inside of scanner. |
| Causes: | Jam has occurred inside the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the Regi. sensor and Regi actuator. Push and release the regi actuator. Check if the pick up module returns the original position. If the sensor is defective, replace it(0604–001393). 3) If the regi sensor is OK, check the scan 2 sensor and exit sensor. • If the scan 2 sensor is defective, replace it(0604–001381). • If the exit sensor is defective, replace it(6107–003581). |
| Error code: | U3-3611, U3-3613 |
| Description: | Original paper jam in the exit area of scanner |
| Causes: | Jam has occurred in exit area of the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If the regi sensor is OK, check the scan 2 sensor and exit sensor. • If the scan 2 sensor is defective, replace it(0604–001381). • If the exit sensor is defective, replace it(6107–003581). |
| Error code: | U3-3614, U3-3713 |
| Description: | Original paper jam in the exit area of scanner |
| Causes: | Jam has occurred in exit area of the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If the regi sensor is OK, check the scan 2 sensor and exit sensor. • If the scan 2 sensor is defective, replace it(0604–001381). • If the exit sensor is defective, replace it(6107–003581). |
| Error code: | U3-4210 |
| Display: | Top door of scanner is open. |
| Description: | Top door of scanner is open. |
| Causes: | DSDF cover is open. |
| Remedy: | 1) Open and close the DSDF cover. Check if the error message is disappeared. 2) If the problem persists, check the cover open sensor. a) Open the DSDF cover. Remove the spring. b) Remove 4 screws. c) Check if the sensor connector is connected correctly. If the sensor is defective, replace it(0604–001393). |
