Samsung MultiXpress K4250RX
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A4
Число страниц в месяц
65000
Скорость печати
A4
25
Цветность печати
черно-белая
Общие характеристики |
|
|---|---|
Макс. формат |
A4 |
Факс |
|
Телефон |
|
Печать фотографий |
|
Размещение |
настольный |
Копир |
|
Тип устройства |
МФУ |
Сканер |
|
Цветность печати |
|
Тип |
лазерный/светодиодный |
Технология печати |
лазерная |
Число страниц в месяц |
65 000 |
Область применения |
средний офис |
Принтер |
|
Печать без полей |
|
Пигментные чернила |
|
Прямая печать |
|
Двусторонняя печать |
|
Макс, разрешение для ч/б печати |
|
| По Y | 1 200 |
| По X | 1 200 |
Скорость ч/б печати |
|
| A4 | 25 |
Время выхода первого отпечатка |
|
| Ч/б | 8,5 |
Копир |
|
Время выхода первой копии |
6,2 |
Макс, количество копий за цикл |
9 999 |
Значение масштаба |
|
| Минимальное | 0,25 |
| Максимальное | 4 |
Макс, разрешение (ч/б) |
|
| По X | 600 |
| По Y | 600 |
Сканер |
|
Стандарт WIA |
|
Слайд-адаптер |
|
Макс. формат оригинала |
A4 |
Тип сканера |
планшетный/протяжный |
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Устройство автоподачи оригиналов |
двустороннее |
Емкость устройства автоподачи оригиналов |
100 |
Разрешение сканера |
|
| По Х | 600 |
| По Х (улучшенное) | 4 800 |
| По Y (улучшенное) | 4 800 |
Скорость сканирования |
|
| Цветн, | 45 |
| Ч/б | 45 |
Расходные материалы |
|
Ресурс ч/б картриджа/тонера |
25 000 |
Количество картриджей |
1 |
Ресурс фотобарабана |
200 000 |
Ресурс девелопера |
400 000 |
Печать на: |
|
| Рулоне |
|
| Пленках |
|
| CD/DVD |
|
| Фотобумаге |
|
| Этикетках |
|
| Карточках |
|
| Матовой бумаге |
|
| Конвертах |
|
| Глянцевой бумаге |
|
Плотность бумаги |
|
| Минимальная | 70 |
| Максимальная | 220 |
Факс |
|
Цветной |
|
PC Fax |
|
Телефон |
|
Спикерфон |
|
Проводная трубка |
|
Беспроводная трубка |
|
АОН |
|
Caller ID |
|
Автоответчик |
|
Стандарт DECT |
|
Языки управления |
|
| PCL 5c |
|
| PostScript 2 |
|
| PPDS |
|
|
|
|
| PostScript |
|
| PCL 5e |
|
| PCL 6 |
|
| PostScript 3 |
|
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
| Стандартная | 1 140 |
| Максимальная | 2 180 |
Финишер |
|
Степлер |
|
Сортер |
|
Электронная сортировка |
|
Сортировка со сдвигом |
|
Брошюровщик |
|
Интерфейсы |
|
Wi-Fi 802.11n |
|
FireWire (IEEE 1394) |
|
AirPrint |
|
LPT |
|
Устройство для чтения карт памяти |
|
Веб-интерфейс |
|
RS-232 |
|
Bluetooth |
|
Wi-Fi |
|
Инфракрасный порт |
|
Версия USB |
2,0 |
USB |
|
Ethernet (RJ-45) |
|
Память/Процессор |
|
Емкость жесткого диска |
320 |
Макс, объем памяти |
2 048 |
Объем памяти |
2 048 |
Дополнительная информация |
|
Работа от аккумулятора |
|
Экран |
|
Диагональ дисплея |
10,1 |
Поддержка ОС |
|
| DOS |
|
| Mac OS |
|
| Windows |
|
| Linux |
|
Потребляемая мощность |
|
| При работе | 1 300 |
| В режиме ожидания | 1,5 |
Уровень шума |
|
| В режиме ожидания | 30 |
| При работе | 53 |
Габариты |
|
Высота |
829 |
Ширина |
566 |
Вес |
61,7 |
Глубина |
610 |
Модули
COVER
CASSETTE-2ND
COVER-SIDE EXIT
Exit
DSDF-EXTERIOR and DSDF-PICK UP
COVER-SIDE MONO
CASSETTE-1ST
DSDF
FRAME MAIN-PICKUP 1ST_2ND
COVER-SIDE DUPLEX
MAIN
DRIVE FUSER EXIT
FRAME-MAIN
FRAME MAIN-ENGINE
MP
Frame main pickup
FRAME MAIN PICKUP UPPER
PLATEN
FRAME-MAIN REGI
DSDF-MAIN FRAME
PLATEN-LOWER
Детали COVER-SIDE EXIT
| Деталь: | COVER-FRONT, K4350,SEC |
| Парткод: | JC95-01902A |
| Деталь: | COVER-MIDDLE RIGHT, X4300,ABS,T 2.5,SEC,S |
| Парткод: | JC63-04523A |
| Деталь: | COVER-INNER, K4350,SEC |
| Парткод: | JC95-01903A |
| Деталь: | COVER-SCAN FRONT, X4300,SEC |
| Парткод: | JC95-01910A |
| Деталь: | COVER-LEFT, K4350,SEC |
| Парткод: | JC95-01913A |
| Деталь: | COVER-LEFT UPPER, X4300,ABS,T 2.5,SEC,9AA |
| Парткод: | JC63-04521A |
| Деталь: | COVER-SCAN LEFT, X4300,ABS,T 2.5,SEC,SPLI |
| Парткод: | JC63-04515A |
| Деталь: | COVER-EXIT, X4300,SEC |
| Парткод: | JC95-01911A |
| Деталь: | COVER-FRONT LOWER, X4300,HIPS,T 2.0,SEC,S |
| Парткод: | JC63-04536A |
| Деталь: | COVER-RIGHT FRONT MONO, K4350,ABS,T 2.5,S |
| Парткод: | JC63-04539A |
| Деталь: | COVER-RIGHT REAR MONO, K4350,ABS,T 2.5,SE |
| Парткод: | JC63-04540A |
| Деталь: | COVER-RIGHT UPPER, X4300,ABS,T 2.5,SEC,9A |
| Парткод: | JC63-04520A |
| Деталь: | COVER-SCAN RIGHT, X4300,ABS,T 2.5,SEC,SPL |
| Парткод: | JC63-04516A |
| Деталь: | COVER-REAR LOWER MONO, K4350,ABS,T 2.5,SE |
| Парткод: | JC63-04542A |
| Деталь: | COVER-REAR UPPER, X4300,ABS,T 2.5,SEC,9AA |
| Парткод: | JC63-04522A |
| Деталь: | COVER-REAR UPPER DUMMY, X4300,ABS,T 2.5,S |
| Парткод: | JC63-04528A |
| Деталь: | COVER-SCAN REAR, X4300,ABS,T 2.5,SEC,SPLI |
| Парткод: | JC63-04518A |
| Деталь: | COVER-EXIT REAR, X4300,SEC |
| Парткод: | JC95-01912A |
| Деталь: | COVER-REAR DUMMY, X4300,ABS,T 2.0,SPLIT B |
| Парткод: | JC63-04567A |
| Деталь: | COVER-EXIT DUMMY, X4300,ABS,T 2.5,SEC,9AA |
| Парткод: | JC63-04526A |
| Деталь: | COVER-DUMMY TABLE, CLX-9201,ABS,T2,W161.9 |
| Парткод: | JC63-03399A |
| Деталь: | CASSETTE-2ND, X4300 |
| Парткод: | JC90-01141B |
| Деталь: | PLATE-KNOCK UP, CLX-9201,EGI-SECC,0.8T,36 |
| Парткод: | JC61-04767A |
| Деталь: | CASSETTE SUB-GUIDE FRONT, X4300 |
| Парткод: | JC90-01290A |
| Деталь: | CASSETTE SUB-GUIDE REAR, X4300 |
| Парткод: | JC90-01291A |
| Деталь: | GEAR-M_PINION 24, SCX-6345N/XRX,POM,1,24, |
| Парткод: | JC66-01020A |
| Деталь: | GEAR-COUPLING LINK, CLX-9201,POM,1.0,60,N |
| Парткод: | JC66-03279A |
| Деталь: | CASSETTE SUB-BRACKET LIFT, X4300 |
| Парткод: | JC90-01278A |
| Деталь: | CASSETTE SUB-LIFTING GEAR, CLX-9201 |
| Парткод: | JC90-01588A |
| Деталь: | GUIDE-LEFT, CLX-9201,HIPS,64,79.3,ICE-GRE |
| Парткод: | JC61-04718A |
| Деталь: | LEVER-LINK SIZE 2ND, CLX-9201,ABS,21.2,19 |
| Парткод: | JC66-03201A |
| Деталь: | LOCKER-CASSETTE 2ND, CLX-9201,POM,BLACK,1 |
| Парткод: | JC64-00716A |
| Деталь: | CASSETTE SUB-COVER, X4300 |
| Парткод: | JC90-01277A |
| Деталь: | BRACKET-RAIL RIGHT, X4300,EGI-SECC,0.8T,P |
| Парткод: | JC61-06148A |
| Деталь: | BRACKET-RAIL LEFT, X4300,EGI-SECC,0.8T,PR |
| Парткод: | JC61-06147A |
| Деталь: | ROLLER IDLE-ORING CST, X4300/K4350,POM,F2 |
| Парткод: | JC66-04761A |
| Деталь: | COVER-SIDE EXIT, X4300,340.5, 74.8 |
| Парткод: | JC95-01509B |
| Деталь: | GUIDE-SIDE EXIT, CLX-9201,MPPO,328.6,47.1 |
| Парткод: | JC61-04791A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | ACTUATOR-FUSER OUT, CLX-9201,MPPO,22.4,24 |
| Парткод: | JC66-03307A |
| Деталь: | SPRING-TS, SUS304,PI0.25,ID3.8,OD4.3,105 |
| Парткод: | 6107-001737 |
| Деталь: | SPRING TS, X4300,PWB-SWPB,0.4,8,6.06 |
| Парткод: | JC61-07362A |
| Деталь: | GUIDE-GATE, CLX-9201,MPPO,336.5,19.1,N300 |
| Парткод: | JC61-04792A |
| Деталь: | HOLDER-EXIT-SENSOR, CLX-9201,MPPO,331.5,3 |
| Парткод: | JC61-04892A |
| Деталь: | EXIT, X4300 |
| Парткод: | JC90-01118B |
| Деталь: | BRACKET-REAR EXIT, CLX-9201,SECC,T1.0,48, |
| Парткод: | JC61-04690A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | BRUSH-EXIT, CLX-9201,SUS FIBER,368,16.9 |
| Парткод: | JC67-00563A |
| Деталь: | GEAR-EXIT, CLX-9350,POM,1.0,16,18.39 |
| Парткод: | JC66-02163A |
| Деталь: | SPRING TS, X4300,STS304,0.4,7.3,2.2 |
| Парткод: | JC61-07185A |
| Деталь: | ACTUATOR-BIN FULL EXIT, X4300/K4350,PC,NH |
| Парткод: | JC66-04339A |
| Деталь: | LEVER-ACTURATOR F_D FULL, CLX-9350,PC,HAZ |
| Парткод: | JC66-02218A |
| Деталь: | LEVER-ACT FULL EXIT, CLX-9350,PC,Black |
| Парткод: | JC66-02278A |
| Деталь: | SHAFT-ACTUATOR EXIT, K4350,STS430,187.0,3 |
| Парткод: | JC66-04753A |
| Деталь: | EXIT-GUIDE UPPER, CLX-9201 |
| Парткод: | JC90-01132A |
| Деталь: | EXIT-GUIDE LOWER, CLX-9201 |
| Парткод: | JC90-01133A |
| Деталь: | ROLLER-FACE DOWN EXIT, CLX-9201,EPDM |
| Парткод: | JC66-03183A |
| Деталь: | GUIDE-UPPER EXIT, CLX-9201,ABS+PC,363.65, |
| Парткод: | JC61-04799A |
| Деталь: | BUSH-L4, CLX-9201,POM,4.2,8,12.5,NATURAL |
| Парткод: | JC61-04805A |
| Деталь: | GUIDE-GATE DUPLEX, CLX-9201,MPPO,324.9,32 |
| Парткод: | JC61-04800A |
| Деталь: | ROLLER-EXIT IDLE, CLX-9201,POM |
| Парткод: | JC61-04806A |
| Деталь: | HOLDER-ROLLER EXIT IDLE, CLX-9201,POM,16, |
| Парткод: | JC61-04898A |
| Деталь: | ROLLER-EXIT IDLE, MLC-500,PFA |
| Парткод: | JC66-00608A |
| Деталь: | SPRING-CS, SUS304,0.5,21.8,5.3,FREE,CLOSE |
| Парткод: | 6107-003050 |
| Деталь: | GUIDE-LOWER EXIT, CLX-9201,MPPO,354,N300X |
| Парткод: | JC61-04801A |
| Деталь: | COVER-ROLLER EXIT, CLX-9201,ABS+PC,82,14. |
| Парткод: | JC63-03422A |
| Деталь: | DSDF-EXTERIOR, X4300/K4350 |
| Парткод: | JC97-04484A |
| Деталь: | DSDF-PICK UP, X4300/K4350 |
| Парткод: | JC97-04495A |
| Деталь: | PBA-DSDF, CLX-9201,SEC,DSDF,FR-4,2L,1688 |
| Парткод: | JC92-02729A |
| Деталь: | BRACKET-PBA, X4300,EGI-SECC,1.0,145,95,PR |
| Парткод: | JC61-06273A |
| Деталь: | BRACKET-REINFORCE PLATEN, X4300,EGI-SECC, |
| Парткод: | JC61-06274A |
| Деталь: | COVER-PLATEN, X4300,ABS,SPLIT BROWN BLACK |
| Парткод: | JC63-04625A |
| Деталь: | DSDF-HINGE R, X4300 |
| Парткод: | JC97-04528A |
| Деталь: | DSDF-HINGE L, X4300 |
| Парткод: | JC97-04527A |
| Деталь: | COVER-DECO RT, ABS,SPLIT BROWN BLACK,780U |
| Парткод: | JC63-04628A |
| Деталь: | GUIDE-HARNESS LT, ABS,HF-0660I,SPLIT BROW |
| Парткод: | JC61-06310A |
| Деталь: | TRAY-ADF OUT, X4300,ABS,SPLIT BROWN BLACK |
| Парткод: | JC63-04603A |
| Деталь: | COVER-PICKUP UPPER, X4300,ABS,SPLIT BROWN |
| Парткод: | JC63-04624A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | ACTUATOR-DETECTOR, X4300,PC,NH-1035P,BLAC |
| Парткод: | JC66-04102A |
| Деталь: | GUIDE-DOC SENSOR, ABS,HF-0660I,SPLIT BROW |
| Парткод: | JC61-06312A |
| Деталь: | DSDF-PICKUP SUB, X4300,SESC |
| Парткод: | JC97-04587A |
| Деталь: | HOLDER-STOPPER PAPER R, ABS,Split brown b |
| Парткод: | JC61-06293A |
| Деталь: | HOLDER-STOPPER PAPER F, ABS,Split brown b |
| Парткод: | JC61-06292A |
| Деталь: | BRACKET-PICKUP LOWER, X4300,EGI-SECC,1.2, |
| Парткод: | JC61-06270A |
| Деталь: | STOPPER-PAPER F, POM,F25-03HT,BLACK,STOPP |
| Парткод: | JC61-06304A |
| Деталь: | BRACKET-PLATEN, EGI-SECC,1.6,PRESS |
| Парткод: | JC61-06199A |
| Деталь: | STOPPER-PAPER R, POM,F25-03HT,BLACK,STOPP |
| Парткод: | JC61-06305A |
| Деталь: | SPRING-ES, STAINLESS-STS304,0.45,3.75,42, |
| Парткод: | 6107-003581 |
| Деталь: | DSDF-PICK UP ROLLER, CLX-8650ND,SEC,WORLD |
| Парткод: | JC97-04099A |
| Деталь: | BELT-TIMING GEAR, S2M,CR+GF+NF |
| Парткод: | 6602-003606 |
| Деталь: | GEAR-PULLEY_DRIVE_FORWARD_Z20, POM,WHITE, |
| Парткод: | JC66-02142A |
| Деталь: | GEAR-PULLEY_DRIVE PU Z24, POM,WHITE,6,14. |
| Парткод: | JC66-02141A |
| Деталь: | STOPPER-PAPER ARM, POM,F25-03HT,black,STO |
| Парткод: | JC61-06303A |
| Деталь: | COVER-SIDE UPPER, K4350,ABS,SPLIT BROWN B |
| Парткод: | JC63-04573A |
| Деталь: | FAN-TYPE 6, 120mA,4.00mmH20,0.424m3/mi |
| Парткод: | JC31-00160C |
| Деталь: | COVER-SIDE MONO, X4300,ABS,SPLIT GRAY (GB |
| Парткод: | JC63-04576A |
| Деталь: | COVER-FRONT MP, ABS,SPLIT GRAY,HF-0660I |
| Парткод: | JC63-03356B |
| Деталь: | MP-TRAY, X4300 |
| Парткод: | JC90-01275A |
| Деталь: | GUIDE-DUPLEX UPPER, CLX-9201,ABS+PC,360.1 |
| Парткод: | JC61-04795A |
| Деталь: | COVER-SIDE EXIT, CLX-9201 |
| Парткод: | JC95-01509A |
| Деталь: | LINK-SIDE, X4300,POM,NATURAL (WHITE) |
| Парткод: | JC66-03220B |
| Деталь: | HANDLE-SIDE, X4300/K4350,ABS,780U,SPLIT B |
| Парткод: | JC64-00948A |
| Деталь: | COVER-SIDE DUPLEX, K4350 |
| Парткод: | JC95-01924A |
| Деталь: | LINK-D, CLX-9201,PC,133.8,BLACK |
| Парткод: | JC66-03235A |
| Деталь: | ROLLER IDLE-DUPLEX, CLX-9201,EPDM,SUM23,6 |
| Парткод: | JC66-03179A |
| Деталь: | COVER-SIDE DUPLEX LOWER, SCX-8128NA |
| Парткод: | JC95-01519A |
| Деталь: | MP GUIDE-MAIN, X4300 |
| Парткод: | JC90-01273A |
| Деталь: | COVER-SIDE TAKE AWAY, CLX-9201 |
| Парткод: | JC95-01516A |
| Деталь: | COVER-HARNESS MONO, K4350,ABS,SPLIT GRAY, |
| Парткод: | JC63-03361B |
| Деталь: | COVER-HARNESS LOWER, X4300/K4350,HIPS,SPL |
| Парткод: | JC63-04574A |
| Деталь: | COVER-SIDE DUPLEX MOTOR, CLX-9201 |
| Парткод: | JC95-01510A |
| Деталь: | LOCKER-SIDE REAR, CLX-9201,POM,NATURAL,60 |
| Парткод: | JC64-00711A |
| Деталь: | BELT-TIMING GEAR, S2M328,RUB(CR),L328 |
| Парткод: | 6602-003299 |
| Деталь: | PULLEY-DUPLEX, CLX-9350,POM(M90-44),BLACK |
| Парткод: | JC66-02350A |
| Деталь: | GEAR-EXIT, CLX-9201,POM,1.0,16,WHITE,18.4 |
| Парткод: | JC66-03292A |
| Деталь: | COVER-SIDE LINK REAR, CLX-9201 |
| Парткод: | JC95-01518A |
| Деталь: | COVER-SIDE ROLLER TR, K4350 |
| Парткод: | JC95-01943A |
| Деталь: | LOCKER-SIDE, CLX-9201,POM,NATURAL,60.5,F2 |
| Парткод: | JC64-00710A |
| Деталь: | GUIDE-HARNESS, CLX-9201,ABS,61,38,HF-0660 |
| Парткод: | JC61-04872A |
| Деталь: | LOCKER-GUIDE-FEED, CLX-9201,POM,BLACK,24. |
| Парткод: | JC64-00709A |
| Деталь: | ROLLER TR, K4350,19,NBR+ECO,310,7.70.2 |
| Парткод: | JC66-04205A |
| Деталь: | CASSETTE-1ST, X4300 |
| Парткод: | JC90-01140B |
| Деталь: | PLATE-KNOCK UP, CLX-9201,EGI-SECC,0.8T,36 |
| Парткод: | JC61-04767A |
| Деталь: | CASSETTE SUB-GUIDE FRONT, X4300 |
| Парткод: | JC90-01290A |
| Деталь: | CASSETTE SUB-GUIDE REAR, X4300 |
| Парткод: | JC90-01291A |
| Деталь: | GEAR-M_PINION 24, SCX-6345N/XRX,POM,1,24, |
| Парткод: | JC66-01020A |
| Деталь: | GEAR-COUPLING LINK, CLX-9201,POM,1.0,60,N |
| Парткод: | JC66-03279A |
| Деталь: | CASSETTE SUB-BRACKET LIFT, X4300 |
| Парткод: | JC90-01278A |
| Деталь: | CASSETTE SUB-LIFTING GEAR, CLX-9201 |
| Парткод: | JC90-01588A |
| Деталь: | GUIDE-LEFT, CLX-9201,HIPS,64,79.3,ICE-GRE |
| Парткод: | JC61-04718A |
| Деталь: | LEVER-LINK SIZE 1ST, CLX-9201,ABS,3,19.2, |
| Парткод: | JC66-03202A |
| Деталь: | LOCKER-CASSETTE 1ST, CLX-9201,POM,BLACK,7 |
| Парткод: | JC64-00715A |
| Деталь: | CASSETTE SUB-COVER, X4300 |
| Парткод: | JC90-01277A |
| Деталь: | BRACKET-RAIL RIGHT, X4300,EGI-SECC,0.8T,P |
| Парткод: | JC61-06148A |
| Деталь: | BRACKET-RAIL LEFT, X4300,EGI-SECC,0.8T,PR |
| Парткод: | JC61-06147A |
| Деталь: | ROLLER IDLE-ORING CST, X4300/K4350,POM,F2 |
| Парткод: | JC66-04761A |
| Деталь: | DSDF-COVER OPEN, X4300/K4350 |
| Парткод: | JC97-04494A |
| Деталь: | DSDF-PICK UP, X4300/K4350 |
| Парткод: | JC97-04495A |
| Деталь: | COVER-FRONT, X4300,ABS,SPLIT BROWN BLACK, |
| Парткод: | JC63-04619A |
| Деталь: | COVER-REAR, X4300,ABS,SPLIT BROWN BLACK,7 |
| Парткод: | JC63-04626A |
| Деталь: | DSDF-MAIN FRAME, X4300/K4350 |
| Парткод: | JC97-04485A |
| Деталь: | DSDF-EXTERIOR, X4300/K4350 |
| Парткод: | JC97-04484A |
| Деталь: | DSDF-STACKER, X4300/K4350 |
| Парткод: | JC97-04496A |
| Деталь: | BRACKET-HINGE COVER OPEN, X4300,EGI-SECC, |
| Парткод: | JC61-06271A |
| Деталь: | GUIDE-DOC R, ABS+PC,NH-1000T,SPLIT BROWN |
| Парткод: | JC61-06217A |
| Деталь: | GUIDE-DOC F, ABS+PC,NH-1000T,SPLIT BROWN |
| Парткод: | JC61-06216A |
| Деталь: | GUIDE-STACKER UPPER, ABS,780U,SPLIT BROWN |
| Парткод: | JC61-06224A |
| Деталь: | GEAR-DOC PINION, POM,1.0,NATURAL (WHITE), |
| Парткод: | JC66-04079A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | ACTUATOR-PAPER LENGTH, X4300,ABS,HF-0660I |
| Парткод: | JC66-04082A |
| Деталь: | RADF-SCATTER, X4300 |
| Парткод: | JC97-04505A |
| Деталь: | GUIDE-STACKER LOWER, ABS,780U,SPLIT BROWN |
| Парткод: | JC61-06223A |
| Деталь: | GEAR-RACK, POM,BLACK,F25-03HT |
| Парткод: | JC66-04072A |
| Деталь: | DAMPER-STACKER, CLX-9201,PORON,1,4,35,NTR |
| Парткод: | JC66-03901A |
| Деталь: | GUIDE-STACKER WIRE, SCX-6345N/XRX,STS,PI1 |
| Парткод: | JC61-01438A |
| Деталь: | FRAME MAIN-PICKUP 1ST, CLX-9201,SEC |
| Парткод: | JC93-00511A |
| Деталь: | FRAME MAIN-PICKUP 2ND, CLX-9201,SEC |
| Парткод: | JC93-00512A |
| Деталь: | SHEET-GUIDE PICKUP, CLX-9210,PET,0.188,32 |
| Парткод: | JC63-03342A |
| Деталь: | GUIDE-PICKUP 1ST, CLX-9201,ABS,328.5,50.5 |
| Парткод: | JC61-04721A |
| Деталь: | GUIDE-HARNESS PICKUP, CLX-9201,ABS,84.22, |
| Парткод: | JC61-04723A |
| Деталь: | FRAME MAIN-PICKUP, CLX-9201,SEC |
| Парткод: | JC93-00510A |
| Деталь: | GUIDE-PICKUP BOTTOM, CLX-9201,ABS,15,332, |
| Парткод: | JC61-04735A |
| Деталь: | GUIDE-PICKUP 2ND, CLX-9201,ABS,328.5,HF-0 |
| Парткод: | JC61-04717A |
| Деталь: | COVER-SIDE DUPLEX, K4350 |
| Парткод: | JC95-01924A |
| Деталь: | GUIDE-TR UPPER, K4350,ABS+PC,NH-1000T,K21 |
| Парткод: | JC61-06515A |
| Деталь: | HARNESS-SIDE DUPLEX_TEMP, SCX-8213ND,UL10 |
| Парткод: | JC39-01654A |
| Деталь: | COVER-SIDE TR LOWER, K4350 |
| Парткод: | JC95-01925A |
| Деталь: | SPRING-CS, SWP B,0.8,21.1,4.5,6.1 |
| Парткод: | 6107-003021 |
| Деталь: | ACTUATOR-DUPLEX 2, CLX-9350,PC HN-1064i,B |
| Парткод: | JC66-02180A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | HOLDER-DUP SNR, SCX-8128NA,ABS,12,46.3,BL |
| Парткод: | JC61-04808A |
| Деталь: | SPRING-TS, SUS304,PI0.25,ID3.8,OD4.3,105 |
| Парткод: | 6107-001737 |
| Деталь: | GUIDE-FEED MONO, SCX-8128NA,ABS+PC,357.8, |
| Парткод: | JC61-04877A |
| Деталь: | LINK-TR REAR, SCX-8128NA,POM,34.6,T2.0,BL |
| Парткод: | JC66-03277A |
| Деталь: | PLATE-GROUND TR, SCX-8128NA,STS304,0.2,22 |
| Парткод: | JC61-04650A |
| Деталь: | PLATE-GROUND_SAW_C, SCX-8040,STS304,0.2,G |
| Парткод: | JC61-03581A |
| Деталь: | ROLLER IDLE-RUBBER-IDLE, SCX-8040ND,POM,S |
| Парткод: | JC66-02289B |
| Деталь: | SHAFT-ROLLER IDLE L, CLX-9350,SUM24L,137. |
| Парткод: | JC66-02354A |
| Деталь: | SPRING-CS, SUS304,PI0.6,L16.6,ID4.7,OD5.9 |
| Парткод: | 6107-001731 |
| Деталь: | PLATE-GROUND_SAW_B, SCX-8040,STS304,0.2,G |
| Парткод: | JC61-03580A |
| Деталь: | PBA-CTD, SL-K4350 |
| Парткод: | JC92-02745A |
| Деталь: | MEA UNIT-TERMINAL:TR, ML-5000A,SAMSUNG,KO |
| Парткод: | JC97-01401A |
| Деталь: | ACTUATOR-CTD, X4300/K4350,PC,NH-1035,BLAC |
| Парткод: | JC66-04059A |
| Деталь: | GUIDE-TR LOWER, X4300,ABS+PC,NH-1000T,BLA |
| Парткод: | JC61-06136A |
| Деталь: | SHEET-TR LOWER R, K4350,PE,0.5 |
| Парткод: | JC63-04566A |
| Деталь: | SHEET-TR LOWER F, K4350,PE,0.5 |
| Парткод: | JC63-04565A |
| Деталь: | EXIT, X4300 |
| Парткод: | JC90-01118B |
| Деталь: | FUSER, K4350,WORLD,230V |
| Парткод: | JC91-01163A |
| Деталь: | FUSER, K4350,WORLD,115V |
| Парткод: | JC91-01164A |
| Деталь: | FRAME MAIN-ENGINE, K4350,SEC |
| Парткод: | JC93-00909A |
| Деталь: | COVER-SIDE MONO, K4350 |
| Парткод: | JC95-01923A |
| Деталь: | CARTRIDGE-WTB MONO, K4350,SEC,WORLD |
| Парткод: | JC96-09196A |
| Деталь: | COVER, K4350,SEC |
| Парткод: | JC95-01901A |
| Деталь: | COVER-OPE, X4300,SEC,WORLD |
| Парткод: | JC95-01928A |
| Деталь: | PLATEN, X4300,SCANNER |
| Парткод: | JC97-04520A |
| Деталь: | DSDF, X4300,K4350 |
| Парткод: | JC97-04498A |
| Деталь: | LSU, K4350,SEC,Dual,A3,600,Dual Beam,780n |
| Парткод: | JC97-04017B |
| Деталь: | HVPS-POLARIS_R MONO, 24V,21.6V26.4V,MAX |
| Парткод: | JC44-00237A |
| Деталь: | SMPS-V2, K7600,PSPN2 TYPE5-V2,AC-DC,220V- |
| Парткод: | JC44-00100D |
| Деталь: | FDB-POLARIS / EVERGREEN_V2, CLX-9201,POL |
| Парткод: | JC44-00211A |
| Деталь: | FAN-TYPE 6, 120mA,4.00mmH20,0.424m3/mi |
| Парткод: | JC31-00160C |
| Деталь: | HDD, 320G,HTS543232A7A384,S63,H16,C16383, |
| Парткод: | JC59-00035A |
| Деталь: | PBA-MAIN, SL-K4350 |
| Парткод: | JC92-02746A |
| Деталь: | SPONGE-WHITE SHEET, X4300,PUR FOAM,Black |
| Парткод: | JC63-04683A |
| Деталь: | CASSETTE-1ST, X4300 |
| Парткод: | JC90-01140B |
| Деталь: | CASSETTE-2ND, X4300 |
| Парткод: | JC90-01141B |
| Деталь: | PBA-OPE HUB, M5370,-,UK,SENSOR |
| Парткод: | JC92-02721A |
| Деталь: | SHIELD-HUB BOARD, X4300,EGI-SECC,0.8,SHIE |
| Парткод: | JC63-04561A |
| Деталь: | COVER-SMPS UPPER, CLX-9201,ABS+PC,267.6,2 |
| Парткод: | JC63-03421A |
| Деталь: | CARTRIDGE SUB-DEVE KIT, K4350,SEC,WORLD |
| Парткод: | JC96-09250A |
| Деталь: | HOLDER-M_HDD, SCX-6345N/XRX,ABS+PC,T2,W11 |
| Парткод: | JC61-01389A |
| Деталь: | HOLDER-HVPS, SCX-8040,HIPS,43.5,174.5,197 |
| Парткод: | JC61-03572A |
| Деталь: | OPE, M5370,SEC |
| Парткод: | JC97-04499A |
| Деталь: | COVER-HINGE LOWER, M5370,ABS,Split Brown |
| Парткод: | JC63-04465A |
| Деталь: | HINGE-OPE, SUM22 |
| Парткод: | JC61-06103A |
| Деталь: | DRIVE-M FUSER EXIT, SEC,OD30.5,NTR,PART,S |
| Парткод: | JC93-00449A |
| Деталь: | BRACKET-M DRIVE FUSER EXIT, SCX-8128NA,EG |
| Парткод: | JC61-04512A |
| Деталь: | GEAR-RDCN EXIT, CLX-9201NA,POM,0.8,1.0,41 |
| Парткод: | JC66-03108A |
| Деталь: | GEAR-M FUSER ONE WAY, SCX-8128NA,POM,0.5, |
| Парткод: | JC66-03141A |
| Деталь: | GEAR-HUB CLUTCH, POM,18.5,10.4,11.3,NW-02 |
| Парткод: | JC66-00340A |
| Цена: | 220 ₽ |
| Деталь: | GEAR-RDCN FUSER OUT, ML-2150,NYLON,1,25,8 |
| Парткод: | JC66-00417A |
| Цена: | 240 ₽ |
| Деталь: | GEAR-RDCN FUSER RELEASE, CLX-9201NA,POM,0 |
| Парткод: | JC66-03106A |
| Деталь: | GEAR-FUSER RELEASE, CLX-9201NA,POM,0.8,43 |
| Парткод: | JC66-03107A |
| Деталь: | MOTOR BLDC, 2000rpm,1200gfcm,24V,2.8A,150 |
| Парткод: | JC31-00123B |
| Цена: | 3 700 ₽ |
| Деталь: | DRIVE-MOTOR STEP, SEC,CLX-9201NA |
| Парткод: | JC93-00452A |
| Деталь: | FRAME-FRONT MONO, K4350,SEC |
| Парткод: | JC93-00901A |
| Деталь: | GUIDE-TONER BOTTLE, K4350,ABS,HF-0660I,BL |
| Парткод: | JC61-06313A |
| Деталь: | FRAME-REGI HOLDER DUST, SCX-8040,SEC,WORL |
| Парткод: | JC93-00078B |
| Цена: | 500 ₽ |
| Деталь: | GUIDE-OPC, SCX-8128NA,HIPS,89.8,430.94,HB |
| Парткод: | JC61-04863A |
| Деталь: | FRAME MAIN-RIGHT CST RAIL, CLX-9201,SEC,W |
| Парткод: | JC93-00478A |
| Деталь: | ROLLER IDLE-FEED, CLX-9201,EPDM,SUS,8 |
| Парткод: | JC66-03203A |
| Деталь: | FRAME MAIN-FEED SENSOR, X4300 |
| Парткод: | JC93-00924A |
| Деталь: | FRAME-MIDDLE SUPPORT FUSER, X4300,SEC,WOR |
| Парткод: | JC93-00467B |
| Деталь: | FRAME-HV PACKAGE MONO, K4350,SEC,WORLD |
| Парткод: | JC93-00891A |
| Деталь: | FRAME-DUCT, K4350,SEC,WORLD |
| Парткод: | JC93-00917A |
| Деталь: | FRAME-DUCT SUCTION, K4350,SEC,WORLD |
| Парткод: | JC93-00893A |
| Деталь: | GEAR-ROLLER FEED, CLX-9201,POM,1,21 |
| Парткод: | JC66-03282A |
| Деталь: | FRAME MAIN-SCAN RIGHT, X4300,SEC |
| Парткод: | JC93-00904A |
| Деталь: | FRAME-REAR MONO, K4350,SEC |
| Парткод: | JC93-00900A |
| Деталь: | HOLDER-SAW, SCX-8040,PC,22.9,18.2,45.5,Tr |
| Парткод: | JC61-03574A |
| Деталь: | WIRE-GUIDE LSU, SCX-8128NA,STS304,,,,,,,, |
| Парткод: | JC66-03274A |
| Деталь: | FRAME MAIN-FRONT LEVER, SCX-8128NA,SEC,WO |
| Парткод: | JC93-00470A |
| Деталь: | FRAME MAIN-SWITCH OPEN, SCX-8128NA,SEC,WO |
| Парткод: | JC93-00466A |
| Деталь: | PHOTO-INTERRUPTER, DIODE,DIP |
| Парткод: | 0604-001381 |
| Деталь: | HOLDER-FEED SENSOR, CLX-9201,ABS,51,BLACK |
| Парткод: | JC61-04857A |
| Деталь: | PBA-ERASER MONO, SL-K4350 |
| Парткод: | JC92-02747A |
| Деталь: | MEA UNIT-TERMINAL:TR, ML-5000A,SAMSUNG,KO |
| Парткод: | JC97-01401A |
| Деталь: | COVER-HV_FRONT, K4350,ABS+PC,BLACK(K21441 |
| Парткод: | JC63-04551A |
| Деталь: | COVER-HV_REAR, K4350,ABS+PC,BLACK(K21441) |
| Парткод: | JC63-04552A |
| Деталь: | DUCT-SUCTION UPPER, K4350,ABS,HF-0660I,BL |
| Парткод: | JC67-00740A |
| Деталь: | FAN, Type7,24,170mA,0.949m3/mi |
| Парткод: | JC31-00161A |
| Деталь: | DUCT-SUCTION LOWER, K4350,ABS,HF-0660I,BL |
| Парткод: | JC67-00739A |
| Деталь: | PBA-PAPER SIZE SENSOR, CLX-9352NA,SEC,FR1 |
| Парткод: | JC92-02622A |
| Деталь: | SENSOR, HSU-07F1V2-N,CLX-9201,045C,+3.3 |
| Парткод: | JC32-00015A |
| Деталь: | FRAME MAIN-MONO, K4350,SEC,WORLD |
| Парткод: | JC93-00889A |
| Деталь: | DRIVE-PICKUP, SEC,5,BLACK,CLX-9201NA |
| Парткод: | JC93-00442A |
| Деталь: | DRIVE-MAIN, K4350,SEC |
| Парткод: | JC93-00912A |
| Деталь: | DRIVE-M FUSER EXIT, SEC,OD30.5,NTR,PART,S |
| Парткод: | JC93-00449A |
| Деталь: | DRIVE-M TONER SUPPLY, SEC,SCX-8128NA |
| Парткод: | JC93-00450A |
| Деталь: | DRIVE-DUCT, SEC,1.1,478.9,75,GRAY,SCX-81 |
| Парткод: | JC93-00451A |
| Деталь: | FRAME-MAIN REGI, X4300 |
| Парткод: | JC93-00910A |
| Деталь: | FRAME MAIN-PICKUP 2ND, CLX-9201,SEC,WORLD |
| Парткод: | JC93-00512A |
| Деталь: | FRAME MAIN-PICKUP 1ST, CLX-9201,SEC |
| Парткод: | JC93-00511A |
| Деталь: | MOTOR BLDC, 2000rpm,1200gfcm,24V,2.8A,150 |
| Парткод: | JC31-00123B |
| Цена: | 3 700 ₽ |
| Деталь: | MOTOR BLDC, 2000rpm,1200gfcm,24V,2.8A,150 |
| Парткод: | JC31-00123A |
| Деталь: | DRIVE-MAIN SUB, K4350,SEC |
| Парткод: | JC93-00911A |
| Деталь: | MP-TRAY, X4300 |
| Парткод: | JC90-01275A |
| Деталь: | MP GUIDE-MAIN, X4300 |
| Парткод: | JC90-01273A |
| Деталь: | MP-BRACKET PICK UP, X4300 |
| Парткод: | JC90-01125B |
| Деталь: | MP-COVER BASE, X4300 |
| Парткод: | JC90-01276A |
| Деталь: | GEAR-IDLE MP, CLX-9201,POM,1,26,NATURAL,2 |
| Парткод: | JC66-03215A |
| Деталь: | GEAR-FORWARD MP, CLX-9201,POM,1,28,30 |
| Парткод: | JC66-03214A |
| Деталь: | FRAME-MAIN PICK UP ROLLER, CLX-9201,0,USA |
| Парткод: | JC93-00540B |
| Деталь: | BRACKET-SOLENOID, CLX-9201,EGI-SECC,0.6T, |
| Парткод: | JC61-04753A |
| Деталь: | HOLDER-TRAY, X4300/K4350,PC,BLACK,NH-1035 |
| Парткод: | JC61-06139A |
| Деталь: | FRAME-TRAY LOWER, X4300/K4350,ABS,780U,SP |
| Парткод: | JC61-06130A |
| Деталь: | FRAME-TRAY PAPER, ABS,SPLIT GRAY,2,HF-066 |
| Парткод: | JC61-05842B |
| Деталь: | FRAME-TRAY COVER, X4300,ABS,SPLIT GRAY,HF |
| Парткод: | JC61-05841B |
| Деталь: | GUIDE-SIDE F, X4300/K4350,ABS,HF-0660i,SP |
| Парткод: | JC61-06133A |
| Деталь: | GUIDE-SIDE R, X4300/K4350,ABS,HF-0660i,SP |
| Парткод: | JC61-06134A |
| Деталь: | GEAR-SENSOR, X4300/K4350,POM,1,42,NATURAL |
| Парткод: | JC66-04062A |
| Деталь: | FRAME-TRAY UPPER, X4300/K4350,ABS,780U,SP |
| Парткод: | JC61-06129A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | SHEET-GUIDE MP, CLX-9201,PET,0.125,25,308 |
| Парткод: | JC63-03358A |
| Деталь: | FRAME-BASE MP, X4300/K4350,PC+GF20%,3020P |
| Парткод: | JC61-06131A |
| Деталь: | COUPLER-TORQUELIMITER, CLX-9350,WHITE,350 |
| Парткод: | JC67-00455A |
| Деталь: | SEAL-PAD MP, CLX-9201N,Teflon Felt,0.7,44 |
| Парткод: | JC62-01085A |
| Деталь: | SOLENOID-MP, CLX-9350,DC24V,18.4,2730, |
| Парткод: | JC33-00029B |
| Деталь: | MP-ONE WAY, CLX-9350,SEC,-,-,- |
| Парткод: | JC90-00918A |
| Деталь: | CLUTCH-P_ONE WAY, SCX-6345N/XRX,STS304,0. |
| Парткод: | JC66-00977A |
| Деталь: | HOLDER-M_IDLE ONE WAY, SCX-6345N/XRX,POM, |
| Парткод: | JC61-01288A |
| Деталь: | GEAR-M PU, CLX-9201,POM,0.7,21,16.1 |
| Парткод: | JC66-03213A |
| Деталь: | STOPPER-PAPER, CLX-9201,POM,9.8,18.2,M90- |
| Парткод: | JC61-04766A |
| Деталь: | LEVER-SOLENOID, CLX-9201,POM,28,22.7,LZ75 |
| Парткод: | JC66-03218A |
| Деталь: | FRAME MAIN-PICKUP, CLX-9201,SEC |
| Парткод: | JC93-00510A |
| Деталь: | FRAME-MAIN PICK UP ROLLER, CLX-9201 |
| Парткод: | JC93-00540A |
| Цена: | 700 ₽ |
| Деталь: | FRAME MAIN-PICKUP UPPER, CLX-9201,SEC |
| Парткод: | JC93-00504A |
| Деталь: | BRACKET-PICKUP REAR, CLX-9201,EGI-SECC,1. |
| Парткод: | JC61-04731A |
| Деталь: | BRACKET-PICKUP FRONT, CLX-9201,EGI-SECC,1 |
| Парткод: | JC61-04730A |
| Деталь: | GEAR-PICKUP, CLX-9201,POM,0.8,31,NATURAL( |
| Парткод: | JC66-03281A |
| Деталь: | SHAFT-FORWARD, CLX-9201,SUS303,225.3,6,ST |
| Парткод: | JC66-03304A |
| Деталь: | FRAME MAIN-PICKUP LOWER, CLX-9201,SEC |
| Парткод: | JC93-00503A |
| Деталь: | LEVER-INPUT CST, CLX-9201,POM,52.9,28.7,M |
| Парткод: | JC66-03200A |
| Деталь: | HOLDER-RETARD, CLX-9201,POM,137,BLACK,M90 |
| Парткод: | JC61-04732A |
| Деталь: | SHAFT-RETARD, CLX-9201,SUM23,137,6,STEEL |
| Парткод: | JC66-03283A |
| Деталь: | COUPLER-TORQUELIMITER, CLX-9350,WHITE,350 |
| Парткод: | JC67-00455A |
| Деталь: | FRAME MAIN-PICKUP BRKT LOWER, CLX-9201,SE |
| Парткод: | JC93-00438A |
| Деталь: | SPRING-CS, SWP B,0.5,26,7.5,FREE,CLOSED E |
| Парткод: | 6107-003049 |
| Деталь: | FIXER-M_E RING 4PI, SCX-6345N/XRX,POM,T1. |
| Парткод: | JC61-01367A |
| Деталь: | FRAME MAIN-PICKUP UPPER, CLX-9201,SEC |
| Парткод: | JC93-00504A |
| Деталь: | FRAME MAIN-PICKUP BRKT UPPER, CLX-9201,SE |
| Парткод: | JC93-00437A |
| Деталь: | SHAFT-PICKUP, CLX-9201,SUM23,129,6,STEEL |
| Парткод: | JC66-03284A |
| Деталь: | ACTUATOR-EMPTY PICKUP, CLX-9201,POM,M90-4 |
| Парткод: | JC66-03199A |
| Деталь: | CLUTCH-P_ONE WAY, SCX-6345N/XRX,STS304,0. |
| Парткод: | JC66-00977A |
| Деталь: | GEAR-M_PU JOINT, SCX-6345N/XRX,POM,0.7,21 |
| Парткод: | JC66-00943A |
| Деталь: | GEAR-M_ONE WAY, SCX-6345N/XRX,POM,0.7,21, |
| Парткод: | JC66-00941A |
| Деталь: | GEAR-M_IDLE PU, SCX-6345N/XRX,POM,0.7,22, |
| Парткод: | JC66-00940A |
| Деталь: | GUIDE-SLIDE PICKUP, CLX-9201,POM,110,45.6 |
| Парткод: | JC61-04722A |
| Деталь: | GUIDE-SUPPORT PICKUP, X3220,PC,158.6,NH-1 |
| Парткод: | JC61-07770A |
| Деталь: | HOLDER-M_IDLE ONE WAY, SCX-6345N/XRX,POM, |
| Парткод: | JC61-01288A |
| Деталь: | SPRING-CS, STAINLESS-STS304,0.5,33,7.5,RI |
| Парткод: | 6107-003046 |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | PLATEN-GLASS SCAN, X4300,SCANNER |
| Парткод: | JC97-04522A |
| Деталь: | PBA-SCAN JOINT, X4300,SEC,FR-4,4L,12745m |
| Парткод: | JC92-02781A |
| Деталь: | GLASS TEMPERED-SCAN ADF, 337.831.1,4.0T |
| Парткод: | JC01-00101A |
| Деталь: | PLATEN-OPEN SENSOR, X4300,SCANNER |
| Парткод: | JC97-04516A |
| Деталь: | PLATEN-FR, X4300,SCANNER |
| Парткод: | JC97-04510A |
| Деталь: | PLATEN-LOWER, X4300,SCANNER |
| Парткод: | JC97-04515A |
| Деталь: | MOTOR STEP 1P, 17PM-K049-P6WS,HB,2,2.2V,4 |
| Парткод: | JC31-00158A |
| Деталь: | BRACKET-HINGE R, X4300,EGI-SECC,2,64.3,99 |
| Парткод: | JC61-06167A |
| Деталь: | BRACKET-HINGE L, X4300,EGI-SECC,2,64.3,99 |
| Парткод: | JC61-06166A |
| Деталь: | COVER-GLASS RIGHT, X4300,ABS,SPLIT BROWN |
| Парткод: | JC63-04580A |
| Деталь: | COVER-GLASS LEFT, X4300,ABS,SPLIT BROWN B |
| Парткод: | JC63-04579A |
| Деталь: | PLATEN-SHIELD CCD, X4300,SCANNER |
| Парткод: | JC97-04502A |
| Деталь: | PLATEN-REAR, X4300,SCANNER |
| Парткод: | JC97-04519A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | LEVER-SENSOR OPEN, X4300,POM,F25-03HT,BLA |
| Парткод: | JC66-04087A |
| Деталь: | HOLDER-SENSOR OPEN, X4300,POM,BLACK,FA-20 |
| Парткод: | JC61-06255A |
| Деталь: | PLATEN-FR LAMP, X4300,SCANNER |
| Парткод: | JC97-04521A |
| Деталь: | MIRROR-FR, X4300,319.611,5,Scanner Mirro |
| Парткод: | JC67-00753A |
| Деталь: | PLATEN-BRACKET RAIL UPPER, X4300,SCANNER |
| Парткод: | JC97-04541A |
| Деталь: | FRAME-REAR, X4300,EGI-SECC,1.0,37.4,549,F |
| Парткод: | JC61-06253A |
| Деталь: | FRAME-MAIN REGI, X4300 |
| Парткод: | JC93-00910A |
| Деталь: | PHOTO-INTERRUPTER, DIODE,DIP |
| Парткод: | 0604-001381 |
| Деталь: | SHAFT-REGI, CLX-9201,SUM 23,361.9,14.7,ST |
| Парткод: | JC66-03302A |
| Деталь: | ROLLER FEED-REGI, X4300/K4350,EPDM,SUM23, |
| Парткод: | JC66-04130A |
| Деталь: | GEAR-ROLLER REGI, CLX-9201,POM,0.8,21,NAT |
| Парткод: | JC66-03293A |
| Деталь: | SPRING-ES, SWPB,0.9,22.4,8.1 |
| Парткод: | 6107-003302 |
| Деталь: | HOLDER-SHAFT REGI, CLX-9201,POM,5,BLACK,A |
| Парткод: | JC61-04897A |
| Деталь: | BRACKET-REGI UPPER, CLX-9201,EGI-SECC,T0. |
| Парткод: | JC61-04685A |
| Деталь: | BRACKET-REGI FRONT, CLX-9201,SECC,T1,63.5 |
| Парткод: | JC61-04686A |
| Деталь: | BRACKET-REGI REAR, CLX-9201,SECC,T1.0,63. |
| Парткод: | JC61-04687A |
| Деталь: | FRAME-MAIN REGI BRACKET, CLX-9201 |
| Парткод: | JC93-00509A |
| Деталь: | DSDF-GUIDE UPPER_SUB, X4300/K4350 |
| Парткод: | JC97-04488A |
| Деталь: | DSDF-SCAN IN, X4300/K4350 |
| Парткод: | JC97-04493A |
| Деталь: | GUIDE-SCAN IN MIDDLE, ABS,HF-0660I,SPLIT |
| Парткод: | JC61-06309A |
| Деталь: | DSDF-GUIDE SCAN OUT_SUB, X4300/K4350 |
| Парткод: | JC97-04490A |
| Деталь: | DSDF-EXIT, X4300 |
| Парткод: | JC97-04504A |
| Деталь: | DSDF-BRACKET SENSOR_SUB, X4300/K4350 |
| Парткод: | JC97-04487A |
| Деталь: | MOTOR BLDC-TYPE1, 3002500rpm,DC 24V,25W, |
| Парткод: | JC31-00156A |
| Деталь: | GUIDE-HARNESS RT, ABS,HF-0660I,SPLIT BROW |
| Парткод: | JC61-06311A |
| Деталь: | ROLLER ADF-REGI, X4300,SUM23,EPDM |
| Парткод: | JC66-04164A |
| Деталь: | ROLLER ADF-SCAN IN, X4300,SUM23,EPDM |
| Парткод: | JC66-04165A |
| Деталь: | BELT-TIMING GEAR, 40S2M130,RUB,W4.0,L130, |
| Парткод: | 6602-001730 |
| Деталь: | BELT-TIMING GEAR, STB40S2M188,T4,L188 |
| Парткод: | 6602-003245 |
| Деталь: | MOTOR STEP 1P, 24V,1.3A |
| Парткод: | JC31-00163A |
| Деталь: | GEAR-PICKUP IDLE, X4300,POM,BLACK,F25-03H |
| Парткод: | JC66-04116A |
| Деталь: | PULLEY-IDLE BLDC MOTOR, POM,BLACK,TS-25A, |
| Парткод: | JC66-04120A |
| Деталь: | CLUTCH-ELECTRIC_G35, 3.5,32,0.8,mA,240Ohm |
| Парткод: | JC47-00038A |
| Деталь: | LINK-COVER OPEN, POM,BLACK |
| Парткод: | JC66-04100A |
| Деталь: | GEAR-PICKUP, X4300,POM,BLACK,F25-03HT |
| Парткод: | JC66-04114A |
| Деталь: | DSDF-DCISM, X4300,NON-MD |
| Парткод: | JC97-04722A |
| Деталь: | DSDF-GUIDE EXIT_SUB, X4300/K4350 |
| Парткод: | JC97-04489A |
| Деталь: | HOLDER-CIS LOCK, ABS,Split brown black,HF |
| Парткод: | JC61-06290A |
| Деталь: | ROLLER ADF-EXIT, X4300,SUM23,EPDM |
| Парткод: | JC66-04163A |
| Деталь: | LEVER-RETARD RELEASE, POM,F25-03HT,ICE GR |
| Парткод: | JC66-04107A |
| Деталь: | BELT-TIMING GEAR, S2M,CR+GF+NF |
| Парткод: | 6602-003607 |
| Деталь: | PULLEY-IDLE_STEP MOTOR, POM,BLACK,F25-03H |
| Парткод: | JC66-04117A |
| Деталь: | BELT-TIMING GEAR, S2M,CR+GF+NF |
| Парткод: | 6602-003606 |
| Деталь: | GEAR-IDLE BLDC MOTOR, X4300,POM,BLACK,F25 |
| Парткод: | JC66-04113A |
| Деталь: | DSDF-HOUSING SEPARATION, X4300,SESC |
| Парткод: | JC97-04586A |
| Деталь: | DSDF-SEPARATION ROLLER, X4300,SESC |
| Парткод: | JC97-04588A |
| Деталь: | FRICTION PAD-GUIDE PICKUP, SCX-6555N,Uret |
| Парткод: | JC69-01326A |
| Деталь: | GUIDE-PICKUP_UPPER, ABS,HF-0660I,SPLIT BR |
| Парткод: | JC61-06284A |
| Деталь: | DSDF-WHITE BAR, X4300/K4350 |
| Парткод: | JC97-04491A |
| Деталь: | LEVER-GUIDE EXIT F, X4300,POM,F25-03HT,IC |
| Парткод: | JC66-04167A |
| Деталь: | LEVER-GUIDE EXIT R, X4300,POM,F25-03HT,BL |
| Парткод: | JC66-04131A |
| Деталь: | GUIDE-SCAN OUT, ABS,HF-0660I,SPLIT BROWN |
| Парткод: | JC61-06285A |
| Деталь: | SPRING-TS, STAINLESS-STS304,1.4,8,6.6,9.4 |
| Парткод: | 6107-003584 |
| Деталь: | GASKET-CONDUCTIVE, SCX-6345N,PUR FOAM,7mm |
| Парткод: | JC63-01173A |
| Деталь: | ROLLER ADF-IDLE EXIT, POM,F25-03HT,BLACK, |
| Парткод: | JC66-04108A |
| Деталь: | SPONGE-EXIT, X4300,PUR FOAM,Black |
| Парткод: | JC63-04682A |
| Деталь: | ROLLER ADF-IDLE, CLX-9350,POM,13.9,23 |
| Парткод: | JC66-02295A |
| Деталь: | ACTUATOR-EXIT, X4300,PC,NH-1035P,BLACK,AC |
| Парткод: | JC66-04104A |
| Деталь: | GUIDE-EXIT_UPPER, ABS+GF20%,GR-4020L,BLAC |
| Парткод: | JC61-06283A |
| Деталь: | BRACKET-EXIT FRONT, X4300,EGI-SECC,1.0,91 |
| Парткод: | JC61-06266A |
| Деталь: | BRACKET-EXIT REAR, X4300,EGI-SECC,1.0,91. |
| Парткод: | JC61-06267A |
| Деталь: | COVER-EXIT SENSOR, ABS,SPLIT BROWN BLACK, |
| Парткод: | JC63-04629A |
| Деталь: | GUIDE-REGI SCAN IN SENSOR, X4300,ABS,HF-0 |
| Парткод: | JC61-06289A |
| Деталь: | ACTUATOR-FEED OUT, PC,NH-1035P,black,ACTU |
| Парткод: | JC66-04105A |
| Деталь: | ACTUATOR-REGI, X4300,PC,NH-1035,BLACK,ACT |
| Парткод: | JC66-04103A |
| Деталь: | PHOTO-INTERRUPTER, DIODE,DIP |
| Парткод: | 0604-001381 |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | DSDF-SEPARATION SUB ROLLER, CLX-8650ND,SE |
| Парткод: | JC97-04148A |
| Деталь: | PLATEN-FFC CCD, X4300,SCANNER |
| Парткод: | JC97-04509A |
| Деталь: | PLATEN-GUIDE HARNESS, X4300,SCANNER |
| Парткод: | JC97-04512A |
| Деталь: | PLATEN-APS, X4300,SCANNER |
| Парткод: | JC97-04507A |
| Деталь: | PLATEN-LENS, X4300,SCANNER |
| Парткод: | JC97-04523A |
| Деталь: | PLATEN-HR, X4300,SCANNER |
| Парткод: | JC97-04514A |
| Деталь: | WIRE-FRONT, X4300,SUS304 |
| Парткод: | JC66-04156A |
| Деталь: | PLATEN-RAIL LOWER F, X4300,SCANNER |
| Парткод: | JC97-04517A |
| Деталь: | FRAME-BASE SCANNER, X4300,EGI-SECC,1.0,47 |
| Парткод: | JC61-06249A |
| Деталь: | PHOTO-INTERRUPTER, PHOTO IC,30mW,BULK |
| Парткод: | 0604-001453 |
| Деталь: | HOLDER-APS, X4300,ABS,BLACK,HF-0660I |
| Парткод: | JC61-06176A |
| Деталь: | BEARING BALL, T.B.D,6.1,17,5.6,ACETAL N23 |
| Парткод: | 6601-003017 |
| Деталь: | GUIDE-FFC LED HR, X4300,POM,F25-03HT,BLAC |
| Парткод: | JC61-06156A |
| Деталь: | MIRROR-HR, X4300,30018,5,Scanner Mirror |
| Парткод: | JC67-00754A |
Коды ошибок
11-2T01, 11-2T11, 11-2T21
11-2T31, 11-2T41, 11-2T61
61-1111
A1-1111, A1-1113
A1-1211, A1-1213
A1-2111, A1-2113
A1-5113, A1-5512
A1-5513, A1-5610
A2-1510, A2-1511, A2-1521
A2-1523, A2-2810, A2-2811
A2-2821, A2-2823, A2-2910
A2-2911, A2-2920, A2-2921
A3-3111, A3-3112
A3-3113, A3-3114
A3-3210, A3-3211, A3-3212
A3-3310, A3-3311, A3-3312
A3-3410, A3-3411, A3-3412
C1-1110, C1-111A
C1-1140, C1-1150
C1-1160, C1-1170
C1-1311, C1-1313, C1-1314
C1-1411
C1-1512
C3-1110, C3-1130, C3-1140
C3-1211
C3-1312
C3-1411
C3-1422
C3-1512
C6-1120
C6-1310
C7-1110, C7-1130
C7-1311
C8-1130
C9-2110, C9-2120
C9-2220
H1-1311, H1-1312, H1-1313
H1-1314, H1-1315
H1-1317, H1-1318
H1-1322
H1-1351, H1-1352, H1-1354
H1-1353
H1-1411, H1-1412
H1-1417, H1-1418
H1-1422
H1-1451, H1-1452, H1-1454
H1-1453
H1-5323
H1-5330
H2-6144
H2-6211, H2-6212
H2-6213, H2-6214
H2-6221, H2-6222
H2-6223, H2-6224
H2-6231, H2-6232
H2-6233, H2-6234
H2-6241, H2-6242
H2-6243, H2-6244
H2-6311
H2-6321, H2-6322, H2-6323
H2-6324, H2-6331, H2-6332
H2-6333, H2-6334
H2-6411
H2-6421, H2-6422
H2-6423, H2-6424
H2-6440, H2-6452
H2-6511, H2-6512
H2-6531, H2-6532
H2-6551, H2-6552
H2-6700, H2-6701, H2-6702
H2-6703, H2-6704, H2-6705
H2-6706
H2-6707, H2-6708
H2-6709, H2-6710
H2-6711, H2-6712
H2-6713, H2-6714
H2-6715, H2-6716
H2-6717, H2-6718
H2-6719, H2-6720
H2-6721, H2-6722
H2-6723
H2-6724, H2-6725
H2-6726, H2-6727
H2-6728, H2-6729
H2-6730, H2-6731
H2-6732, H2-6733
H2-6734
H2-6735
H2-6736, H2-6737
H2-6738, H2-6739
H2-6740, H2-6741
H2-6742, H2-6743
H2-6744
H2-6A50
H2-6A63
M1-1113, M2-1121
M1-1213, M2-1131
M1-1610
M1-3122
M1-3222
M1-4111
M1-4211
M1-5111, M1-5112
M1-5113, M1-5120
M1-5211, M1-5212
M1-5612
M2-1124, M2-1125
M2-1134, M2-1135
M2-1211, M2-1213, M2-1214
M2-1331, M2-1333, M2-1334
M2-2111, M2-2113, M2-2114
M3-1411, M3-1413, M3-1414
M3-2230, M3-2430
S1-1113
S1-1114
S1-1313
S1-2111
S1-2411, S1-2421, S1-2422
S1-2510, S1-2511, S1-2520
S1-2521 S1-2523 S1-2540
S1-4111
S1-4311
S1-5221
S2-1211, S2-2311
S2-3321
S2-3421
S2-4210
S2-4410
S3-3121
S3-3211, S3-3213, S3-3214
S3-3215, S3-3216, S3-3217
S4-3111
S5-3111
S6-3122
S6-3123, S6-3128
S7-1110
S7-2110
U1-2113, U1-2119
U1-2115
U1-2132, U1-2135
U1-2141, U1-2142
U1-2316, U1-2317
U1-2335, U1-233A
U1-2337, U1-233D
U2-1111, U2-1112
U2-1113, U2-1114
U3-3122
U3-3211, U3-3213, U3-3214
U3-3311, U3-3313, U3-3314
U3-3413, U3-3414, U3-3511
U3-3513, U3-3514
U3-3611, U3-3613
U3-3614, U3-3713
U3-4210
Описание
| Error code: | 11-2T01, 11-2T11, 11-2T21 |
| Display: | Tray paper mismatch Tray 1 paper mismatch Tray 2 paper mismatch Tray 3 paper mismatch Tray 4 paper mismatch MP tray paper mismatch |
| Description: | Load tray with [Letter], [Plain] paper Load tray 1 with [Letter], [Plain] paper Load tray 2 with [Letter], [Plain] paper Load tray 3 with [Letter], [Plain] paper Load tray 4 with [Letter], [Plain] paper Load MP with [Letter], [Plain] paper |
| Causes: | Paper in tray is not matched to the machine paper setting. |
| Remedy: | 1) Check and change the paper setting of the corresponding tray properly. |
| Error code: | 11-2T31, 11-2T41, 11-2T61 |
| Display: | Tray paper mismatch Tray 1 paper mismatch Tray 2 paper mismatch Tray 3 paper mismatch Tray 4 paper mismatch MP tray paper mismatch |
| Description: | Load tray with [Letter], [Plain] paper Load tray 1 with [Letter], [Plain] paper Load tray 2 with [Letter], [Plain] paper Load tray 3 with [Letter], [Plain] paper Load tray 4 with [Letter], [Plain] paper Load MP with [Letter], [Plain] paper |
| Causes: | Paper in tray is not matched to the machine paper setting. |
| Remedy: | 1) Check and change the paper setting of the corresponding tray properly. |
| Error code: | 61-1111 |
| Description: | Booting Failure: #61-1111. Turn off then on. Call for service if the problem persists |
| Causes: | Hibernation image creation is failed. |
| Remedy: | 1) Turn the machine on with a normal booting. 2) Enter the SVC mode. Select “Hibernation On” again. |
| Error code: | A1-1111, A1-1113 |
| Display: | Motor Failure: #A1-1111. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-1113. Turn off then on. Call for service if the problem persists. |
| Description: | Motor Failure: #A1-1111. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-1113. Turn off then on. Call for service if the problem persists. |
| Causes: | Regi/MP motor operation is abnormal. • A1–1111 : Regi/MP motor is stopped but machine recognizes it as operational. • A1–1113 : Regi/MP motor is operating but machine recognizes status as "Stopped". |
| Remedy: | 1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Open the side cover. Check if there are any foreign substances or paper around Regi./MP unit. 3) Remove the rear cover. 4) Check if the Regi/MP motor connector is connected correctly. 5) If the connection is OK, turn the machine on. Enter SVC mode. Select motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100–0000) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the motor(JC31-00123B). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board (JC44-00100C (220V) / JC44-00093C (110V)). - If the control signal is abnormal, replace the main board(JC92-02742A). b) If the motor is operational, • Check the Pin Num 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness. |
| Error code: | A1-1211, A1-1213 |
| Display: | Motor Failure: #A1-1211. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-1213. Turn off then on. Call for service if the problem persists. |
| Description: | Motor Failure: #A1-1211. Turn off then on. Call for service if the problem persists Motor Failure: #A1-1213. Turn off then on. Call for service if the problem persists |
| Causes: | Fuser motor operation is abnormal. • A1–1211 : Fuser motor is stopped but machine recognizes it as operational. • A1–1213 : Fuser motor is operating but recognizes status as "Stopped". |
| Remedy: | 1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Open the side cover. Check if there are any foreign substances or paper around fuser unit. 3) Remove the rear cover. 4) Check if the fuser motor connector is connected correctly. 5) If the connection is OK, turn the machine on. Enter SVC mode. Select motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100–0120) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the motor(JC31-00123B). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board (JC44-00100C (220V) / JC44-00093C (110V)). - If the control signal is abnormal, replace the main board(JC92-02742A). b) If the motor is operational, • Check the Pin Num 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness. |
| Error code: | A1-2111, A1-2113 |
| Display: | Motor Failure: #. Turn off then on. Call for service if the problem persists. |
| Description: | Motor Failure: #A1-2111. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-2113. Turn off then on. Call for service if the problem persists. |
| Causes: | OPC motor does not operate. / OPC motor is operational but machine recognizes status as stopped. |
| Remedy: | 1) Turn the machine off then on. If the error persists, turn the machine off again. 2) Open the side cover. Check if there are any foreign substances or paper around drum drive unit. 3) Remove the rear cover 4) Check if the OPC motor connector is connected correctly. 5) If the connection is OK, turn the machine on. Enter the SVC mode. Select the yellow OPC motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100–0044) a) If the motor does not operates. i) Check the signal and power with the DVM. ii) If the checked result is normal, replace the BLDC motor(JC31-00123B). iii) If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board (JC44-00100C (220V) / JC44-00093C (110V)). - if the control signal is abnormal, replace the main board(JC92–02746A) b) If the motor is operational, check the Pin Num 8. i) If the value is abnormal, replace the main board. ii) If the value is normal, replace the harness. |
| Error code: | A1-5113, A1-5512 |
| Description: | Motor Failure: #A1-5113. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-5512. Turn off then on. Call for service if the problem persists. |
| Causes: | The motor related to toner supply has a problem. |
| Remedy: | 1) Open the front cover. If the toner pipe is blocked, open it. 2) Turn the machine off then on. If the error persists, check the following steps. 3) Enter the SVC mode. Select the toner supply motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 111-0030) 4) If the motor does not operate, measure the motor power with DVM. - Measure two points together. a) If 24V power is supplied, replace the toner supply motor(JC31-00123B). b) If 24V power is not supplied, check the SMPS and main board i) If 24V power is not generated, replace the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)). ii) If the control signal is abnormal, replace the main board(JC92–02746A). |
| Error code: | A1-5513, A1-5610 |
| Description: | Motor Failure: #A1-5513. Turn off then on. Call for service if the problem persists. Motor Failure: #A1-5610. Turn off then on. Call for service if the problem persists. |
| Causes: | The motor related to toner supply has a problem. |
| Remedy: | 1) Open the front cover. If the toner pipe is blocked, open it. 2) Turn the machine off then on. If the error persists, check the following steps. 3) Enter the SVC mode. Select the toner supply motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 111-0030) 4) If the motor does not operate, measure the motor power with DVM. - Measure two points together. a) If 24V power is supplied, replace the toner supply motor(JC31-00123B). b) If 24V power is not supplied, check the SMPS and main board i) If 24V power is not generated, replace the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)). ii) If the control signal is abnormal, replace the main board(JC92–02746A). |
| Error code: | A2-1510, A2-1511, A2-1521 |
| Description: | Fan Failure: #A2-xxxx. Turn off then on. Call for service if the problem persists Fan Failure: #A2-xxxx. Open the door, then close it. Call for service if the problem persists |
| Causes: | Fan does not operate or fan signal is abnormal. NOTE • Duplex fan error : A2–1510 / A2–1511 / A2–1521 / A2–1523 • Deve fan error : A2–2810 / A2–2811 / A2–2821 / A2–2823 • OPC blow-in fan error : A2–2910 / A2–2911 / A2–2920 / A2–2921 |
| Remedy: | 1) Turn the machine off. 2) Remove the rear cover. 3) Check if the corresponding fan connector is connected correctly. 4) If the connection is OK, enter the SVC mode and execute fan test. (Diagnostics > Engine Dignostics > Engine Test Routines) 5) If the fan does not operate, measure the fan power. (Red line) - Measure the red line a) If 24V power is generated, replace the defective fan. b) If 24V power is not generated, check the SMPS and main board. i) Measure 24V power on the SMPS board. If the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)) is defective, replace it. ii) If the SMPS board is normal, replace the main board. 6) If the fan operation is normal but the error persists, a) Check the yellow line signal with DVM. b) Check fan operation as connection or disconnection. i) If the lock signal is 0V continually, check the harness. ii) If the harness is OK, replace the main board(JC92–02746A). iii) If the signal value is different from the table above, replace the defective fan. • Deve fan : JC31–00161A • Duplex fan : JC31–00160B |
| Error code: | A2-1523, A2-2810, A2-2811 |
| Description: | Fan Failure: #A2-xxxx. Turn off then on. Call for service if the problem persists Fan Failure: #A2-xxxx. Open the door, then close it. Call for service if the problem persists |
| Causes: | Fan does not operate or fan signal is abnormal. NOTE • Duplex fan error : A2–1510 / A2–1511 / A2–1521 / A2–1523 • Deve fan error : A2–2810 / A2–2811 / A2–2821 / A2–2823 • OPC blow-in fan error : A2–2910 / A2–2911 / A2–2920 / A2–2921 |
| Remedy: | 1) Turn the machine off. 2) Remove the rear cover. 3) Check if the corresponding fan connector is connected correctly. 4) If the connection is OK, enter the SVC mode and execute fan test. (Diagnostics > Engine Dignostics > Engine Test Routines) 5) If the fan does not operate, measure the fan power. (Red line) - Measure the red line a) If 24V power is generated, replace the defective fan. b) If 24V power is not generated, check the SMPS and main board. i) Measure 24V power on the SMPS board. If the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)) is defective, replace it. ii) If the SMPS board is normal, replace the main board. 6) If the fan operation is normal but the error persists, a) Check the yellow line signal with DVM. b) Check fan operation as connection or disconnection. i) If the lock signal is 0V continually, check the harness. ii) If the harness is OK, replace the main board(JC92–02746A). iii) If the signal value is different from the table above, replace the defective fan. • Deve fan : JC31–00161A • Duplex fan : JC31–00160B |
| Error code: | A2-2821, A2-2823, A2-2910 |
| Description: | Fan Failure: #A2-xxxx. Turn off then on. Call for service if the problem persists Fan Failure: #A2-xxxx. Open the door, then close it. Call for service if the problem persists |
| Causes: | Fan does not operate or fan signal is abnormal. NOTE • Duplex fan error : A2–1510 / A2–1511 / A2–1521 / A2–1523 • Deve fan error : A2–2810 / A2–2811 / A2–2821 / A2–2823 • OPC blow-in fan error : A2–2910 / A2–2911 / A2–2920 / A2–2921 |
| Remedy: | 1) Turn the machine off. 2) Remove the rear cover. 3) Check if the corresponding fan connector is connected correctly. 4) If the connection is OK, enter the SVC mode and execute fan test. (Diagnostics > Engine Dignostics > Engine Test Routines) 5) If the fan does not operate, measure the fan power. (Red line) - Measure the red line a) If 24V power is generated, replace the defective fan. b) If 24V power is not generated, check the SMPS and main board. i) Measure 24V power on the SMPS board. If the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)) is defective, replace it. ii) If the SMPS board is normal, replace the main board. 6) If the fan operation is normal but the error persists, a) Check the yellow line signal with DVM. b) Check fan operation as connection or disconnection. i) If the lock signal is 0V continually, check the harness. ii) If the harness is OK, replace the main board(JC92–02746A). iii) If the signal value is different from the table above, replace the defective fan. • Deve fan : JC31–00161A • Duplex fan : JC31–00160B |
| Error code: | A2-2911, A2-2920, A2-2921 |
| Description: | Fan Failure: #A2-xxxx. Turn off then on. Call for service if the problem persists Fan Failure: #A2-xxxx. Open the door, then close it. Call for service if the problem persists |
| Causes: | Fan does not operate or fan signal is abnormal. NOTE • Duplex fan error : A2–1510 / A2–1511 / A2–1521 / A2–1523 • Deve fan error : A2–2810 / A2–2811 / A2–2821 / A2–2823 • OPC blow-in fan error : A2–2910 / A2–2911 / A2–2920 / A2–2921 |
| Remedy: | 1) Turn the machine off. 2) Remove the rear cover. 3) Check if the corresponding fan connector is connected correctly. 4) If the connection is OK, enter the SVC mode and execute fan test. (Diagnostics > Engine Dignostics > Engine Test Routines) 5) If the fan does not operate, measure the fan power. (Red line) - Measure the red line a) If 24V power is generated, replace the defective fan. b) If 24V power is not generated, check the SMPS and main board. i) Measure 24V power on the SMPS board. If the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)) is defective, replace it. ii) If the SMPS board is normal, replace the main board. 6) If the fan operation is normal but the error persists, a) Check the yellow line signal with DVM. b) Check fan operation as connection or disconnection. i) If the lock signal is 0V continually, check the harness. ii) If the harness is OK, replace the main board(JC92–02746A). iii) If the signal value is different from the table above, replace the defective fan. • Deve fan : JC31–00161A • Duplex fan : JC31–00160B |
| Error code: | A3-3111, A3-3112 |
| Display: | Sensor Failure: #. Turn off then on. Call for service if the problem persists. |
| Description: | Sensor Failure: #A3-3111. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3112. Turn off then on. Call for service if the problem persists |
| Causes: | The NC sensor in the fuser unit is defective. / The sensor signal is abnormal due to a defective harness. • A3–3111 : Center NC sensor is in short status. • A3–3112 : Center NC sensor is in open status. • A3–3113 : Side NC sensor is in short status. • A3–3114 : Side NC sensor is in open status. |
| Remedy: | 1) Enter SVC mode. Execute sensor test to check the sensor operation. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 109-0000 : Fuser Temperature A • 109-0010 : Fuser Temperature B 3) Measure the resistance value of the thermistor (1404-001453). If the measured value is out of 307KΩ~430KΩ @25℃, replace the thermistor. 4) Install the fuser unit after replacing the thermistor. 5) If the error persists, replace the fuser unit (JC91-01157A(220V) / JC91–01158A (110V)). 6) If the error persists after replacing fuser unit, replace the main board(JC92–02742A). |
| Error code: | A3-3113, A3-3114 |
| Display: | Sensor Failure: #. Turn off then on. Call for service if the problem persists. |
| Description: | Sensor Failure: #A3-3113. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3114. Turn off then on. Call for service if the problem persists |
| Causes: | The NC sensor in the fuser unit is defective. / The sensor signal is abnormal due to a defective harness. • A3–3111 : Center NC sensor is in short status. • A3–3112 : Center NC sensor is in open status. • A3–3113 : Side NC sensor is in short status. • A3–3114 : Side NC sensor is in open status. |
| Remedy: | 1) Enter SVC mode. Execute sensor test to check the sensor operation. (Diagnostics > Engine Diagnostics > Engine Test Routines) • 109-0000 : Fuser Temperature A • 109-0010 : Fuser Temperature B 3) Measure the resistance value of the thermistor (1404-001453). If the measured value is out of 307KΩ~430KΩ @25℃, replace the thermistor. 4) Install the fuser unit after replacing the thermistor. 5) If the error persists, replace the fuser unit (JC91-01157A(220V) / JC91–01158A (110V)). 6) If the error persists after replacing fuser unit, replace the main board(JC92–02742A). |
| Error code: | A3-3210, A3-3211, A3-3212 |
| Display: | Sensor Failure: #. Turn off then on. Call for service if the problem persists. |
| Description: | Sensor Failure: #A3-3210. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3211. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3212. Turn off then on. Call for service if the problem persists |
| Causes: | Inner temperature sensor is defective. • A3–3210 : Inner temperature sensor value is abnormal. • A3–3211 : Inner temperature sensor is in short status. • A3–3212 : Inner temperature sensor is in open status. |
| Remedy: | 1) Open the side cover. Check the connection. • If the connection is OK, replace the photo sensor (1404-001417). 2) If the sensor is normal, replace the main board(JC92-02742A). |
| Error code: | A3-3310, A3-3311, A3-3312 |
| Display: | Sensor Failure: #A3-3310. Turn off then on. Call for service if the problem persists. Actuator Fan Failure #: Turn off then on. |
| Description: | Sensor Failure: #A3-3310. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3311. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3312. Turn off then on. Call for service if the problem persists |
| Causes: | Outer temperature/humidity sensor is defective. • A3–3310 / A3–3311 / A3–3312 : Temperature function is abnormal. • A3–3410 / A3–3411 / A3–3412 : Humidity function is abnormal. |
| Remedy: | 1) Remove the left cover. Unplug and reconnect the sensor harness. If the error persists, replace the sensor(JC93-00486A). 2) If the harness and sensor are normal, replace the main board (JC92-02742A). |
| Error code: | A3-3410, A3-3411, A3-3412 |
| Display: | Sensor Failure: #A3-3310. Turn off then on. Call for service if the problem persists. Actuator Fan Failure #: Turn off then on. |
| Description: | Sensor Failure: #A3-3410. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3411. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3412. Turn off then on. Call for service if the problem persists |
| Causes: | Outer temperature/humidity sensor is defective. • A3–3310 / A3–3311 / A3–3312 : Temperature function is abnormal. • A3–3410 / A3–3411 / A3–3412 : Humidity function is abnormal. |
| Remedy: | 1) Remove the left cover. Unplug and reconnect the sensor harness. If the error persists, replace the sensor(JC93-00486A). 2) If the harness and sensor are normal, replace the main board (JC92-02742A). |
| Error code: | C1-1110, C1-111A |
| Display: | C1-1110, C1-111A Toner error |
| Description: | Prepare new yellow toner cartridge. Shake toner cartridge and then install. Replace toner cartridge if the problem persists |
| Causes: | Toner remained is 5 ~ 30% of its life. |
| Remedy: | 1) Order new yellow toner cartridge because toner cartridge with level of “Low” will be exhausted soon. |
| Error code: | C1-1140, C1-1150 |
| Description: | End of life, Replace with new toner cartridge Replace with new toner cartridge |
| Causes: | Symptom The toner cartridge is at the end of its life. |
| Remedy: | 1) Open the front cover. 2) Remove the toner cartridge. 3) Install the new toner cartridge. 4) Close the toner cartridge. |
| Error code: | C1-1160, C1-1170 |
| Description: | End of life, Replace with new toner cartridge Replace with new toner cartridge |
| Causes: | Symptom The toner cartridge is at the end of its life. |
| Remedy: | 1) Open the front cover. 2) Remove the toner cartridge. 3) Install the new toner cartridge. 4) Close the toner cartridge. |
| Error code: | C1-1311, C1-1313, C1-1314 |
| Description: | Toner Cartridge Failure: #C1-1311. Install toner cartridge again Shake toner cartridge and then install. Call for service if the problem persists Did not supply enough toner. Remove seal tape of toner cartridge or shake it. Call for service if the problem persists |
| Causes: | Toner supply is inefficient or abnormal. |
| Remedy: | 1) Turn the machine off. Open the front cover 2) Remove the toner cartridge. Shake the toner cartridge horizontally to distribute the toner evenly inside the cartridge. 3) If the problem persists, check the follows. a) Check if the Toner Supply Drive Unit(JC93–00436A) is defective. b) Check if the Toner Duct Drive Unit(JC93–00451A) is defective. 4) If the problem persists, replace the toner cartridge. 5) If the problem persists, replace the drum unit. |
| Error code: | C1-1411 |
| Display: | Toner cartridge is not installed. Install it. |
| Description: | Toner cartridge is not installed. Install the cartridge |
| Causes: | The toner cartridge is not installed. / The machine can’t detect the toner cartridge. |
| Remedy: | 1) Turn the machine off then on. 2) Remove the toner cartridge. Thoroughly roll the cartridge five or six times to distribute the toner evenly inside the cartridge. And reinstall the toner cartridge. 3) Check if the CRUM contact area is contaminated. Clean it. |
| Error code: | C1-1512 |
| Display: | Toner cartridge is not compatible. Check users guide. |
| Description: | Toner cartridge is not compatible. Check users guide. |
| Causes: | Toner cartridge is not compatible. |
| Remedy: | 1) Print the supply information report. Check information of the toner cartridge. 2) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one. |
| Error code: | C3-1110, C3-1130, C3-1140 |
| Display: | Prepare new imaging unit Replace with new imaging unit. |
| Description: | Prepare new imaging unit Replace with new imaging unit. |
| Causes: | The Imaging unit has almost reached the end of life. |
| Remedy: | 1) Open the front cover and remove the waste toner container. 2) Remove the imaging unit. 3) If its life is at the end, replace the drum unit and developer with new one. |
| Error code: | C3-1211 |
| Display: | Imaging Unit Failure:#C3-1211. Please turn off then on. |
| Description: | Imaging Unit Failure:#C3-1211. Please turn off then on. |
| Causes: | Sensor calibration error that detects the toner density for image stabilization control has occurred. |
| Remedy: | 1) Open the front cover and remove the waste toner container. 2) Remove the imaging unit. 3) If its life is at the end, replace the drum unit and developer with new one. |
| Error code: | C3-1312 |
| Display: | Imaging Unit Failure: #C3-1312. Install imaging unit again. |
| Description: | Imaging Unit Failure: #C3-1312. Install imaging unit again |
| Causes: | Toner supply is inefficient or abnormal. |
| Remedy: | 1) Turn the machine off. Open the front cover 2) Remove the toner cartridge. Shake the toner cartridge horizontally to distribute the toner evenly inside the cartridge. 3) If the problem persists, check the follows. a) Check if the Toner Supply Drive Unit(JC93–00436A) is defective. b) Check if the Toner Duct Drive Unit(JC93–00451A) is defective. 4) If the problem persists, replace the toner cartridge. 5) If the problem persists, replace the drum unit. |
| Error code: | C3-1411 |
| Display: | Imaging unit is not installed. Install the unit. |
| Description: | Imaging unit is not installed. Install the unit |
| Causes: | The imaging unit is not installed. / The machine can’t detect the imaging unit. |
| Remedy: | 1) Open the front cover. Check if the imaging unit is installed. 2) Remove and reinstall the imaging unit. 3) Check if the contact terminal is contaminated or broken. Clean the contact terminal. 4) Check if the CRUM harness is connected correctly. Reconnect it. 5) If the harness is defective, replace it. 6) If the problem persists, replace the imaging unit with new one. |
| Error code: | C3-1422 |
| Display: | Imaging unit is not installed. Install the unit. |
| Description: | Imaging unit requires chargers cleaning. Clean the unit. |
| Causes: | The imaging unit needs to clean. |
| Remedy: | 1) Open the front cover and remove the waste toner container. 2) Clean the drum unit by charger cleaner. 3) If its life is at the end, replace the drum unit and developer with new one. |
| Error code: | C3-1512 |
| Display: | Imaging unit is not compatible. Check user`s guide |
| Description: | Imaging unit is not compatible. Check the user guide |
| Causes: | Imaging unit is not compatible. |
| Remedy: | 1) Open the front cover. Remove the imaging unit. 2) Check if the label information of the imaging unit is same with the machine’s one. (ex. /SEE) 3) If label information is different from the machine or the imaging unit is not a samsung genuine, replace it with a new one. |
| Error code: | C6-1120 |
| Display: | Replace new Fuser unit |
| Description: | Replace with new fuser unit |
| Causes: | The life of the fuser unit has expired. |
| Remedy: | 1) Turn the machine off. 2) Replace the fuser unit(JC91-01157A (220V) /JC91-01158A (110V)). 3) Turn the machine on. |
| Error code: | C6-1310 |
| Display: | Fuser unit is not installed. Install it |
| Description: | Fuser unit is not installed. Install it. |
| Causes: | The fuser unit is not installed or fuser unit connector is not connected properly. |
| Remedy: | 1) Turn the machine off then on. 2) If the problem persists, turn the machine off again. 3) Open the side cover. Check if the fuser unit is installed. If not, install the fuser unit. 4) If the fuser unit is installed, remove it. 5) Check if the fuser draw connector (JC39–01677A) is broken or defective. 6) Install the fuser unit. 7) If the problem persists, replace the fuser unit(JC91-01157A (220V) /JC91-01158A (110V)). |
| Error code: | C7-1110, C7-1130 |
| Display: | Waste toner container is almost full. Order new one. Waste toner container is full. Replace it. |
| Description: | Waste toner container is almost full. Order new one. Waste toner container is full. Replace it. |
| Causes: | The life of the waste toner container expires soon or has expired. |
| Remedy: | 1) Open the front cover. 2) Remove the waste toner container. Install a new waste toner container. 3) Close the front cover. |
| Error code: | C7-1311 |
| Display: | Waste toner container is not installed. Install it. |
| Description: | Not Installed Waste tank |
| Causes: | The waste toner container is not installed |
| Remedy: | 1) Check if the waste toner container is installed properly. 2) Remove and reinstall the waste toner container. |
| Error code: | C8-1130 |
| Description: | Replace with new magenta developer unit |
| Causes: | The life of the developer unit has expired. |
| Remedy: | 1) Turn the machine off. 2) Open the front cover and remove the waste toner container. 3) Remove the imaging unit. 4) If the life of the developer unit has expired, replace the developer unit with new one. |
| Error code: | C9-2110, C9-2120 |
| Display: | Replace with new Transfer roller. |
| Description: | Replace with new Transfer roller. |
| Causes: | The life of the second transfer roller(T2) expires soon or has expired. |
| Remedy: | 1) Open the side cover. 2) Replace the second transfer roller(JC95-01942A) with a new one. 3) Close the side cover. 4) Enter SVC mode. • To enter the service mode, tap "Service Mode" App. When the password dialog box appears, enter “1934” and press the “OK” button. 5) Select “TRANSFER” (INFORMATION > Supply Status > Field Replacement Unit > TRANSFER) 6) Select “T2 Roller”. The “RESET” button will be activated. Click “RESET” to clear the T2 Roller count. 7) Exit the SVC mode by pushing the home button. |
| Error code: | C9-2220 |
| Display: | TR Failure: #C9-2220. Install transfer roller again. |
| Description: | TR Failure: #C9-2220. Install transfer roller again |
| Causes: | The life of the second transfer roller(T2) is not installed. |
| Remedy: | 1) Open the side cover. 2) Remove and reinstall the second transfer roller. 3) Close the side cover. 4) If the problem persists, replace the HVPS board(JC44–00212A). |
| Error code: | H1-1311, H1-1312, H1-1313 |
| Description: | Paper jam in Tray 3. |
| Causes: | Paper jam has occurred in tray3. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.) |
| Remedy: | 1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray3. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray3. 3) If this jam error occurs frequently, check the rollers below. a) Remove the tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit1. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit1. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit1. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit1(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A). |
| Error code: | H1-1314, H1-1315 |
| Description: | Paper jam in Tray 3. |
| Causes: | Paper jam has occurred in tray3. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.) |
| Remedy: | 1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray3. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray3. 3) If this jam error occurs frequently, check the rollers below. a) Remove the tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit1. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit1. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit1. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit1(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A). |
| Error code: | H1-1317, H1-1318 |
| Display: | Paper jam in Tray 3. |
| Description: | Paper jam in Tray 3. |
| Causes: | Paper jam has occurred in tray3. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.) |
| Remedy: | 1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray3. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray3. 3) If this jam error occurs frequently, check the rollers below. a) Remove the tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit1. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit1. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit1. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit1(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A). |
| Error code: | H1-1322 |
| Display: | Tray 3 cassette is pulled out. Insert it properly. |
| Description: | Tray 3 cassette is pulled out. Insert it properly. |
| Causes: | Tray 3 is pulled out or the auto size sensor connector is not connected or broken. |
| Remedy: | 1) Remove and insert tray3 correctly. 2) If the problem persists, remove tray3 and tray4. Look inside machine. 3) Check if the auto size sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the auto size sensor(JC93-00018A). 5) If the problem persists, replace the DCF board(JC92-02453A). |
| Error code: | H1-1351, H1-1352, H1-1354 |
| Display: | Paper is low in Tray 3. Load paper. Paper is empty in tray 3. Load paper. |
| Description: | Paper is low in Tray 3. Load paper. Paper is empty in Tray 3. Load paper. |
| Causes: | Paper in the tray is less than 10% of specification. / The photo sensor is defective. |
| Remedy: | 1) Remove tray3. Load the paper in tray3. 2) If paper is loaded but error message has not disappeared, check the following. a) Remove the DCF pick up unit1. b) Check if the photo sensor in the DCF pick up unit1 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. d) If the actuator(JC66-03199A) is defective, replace it. |
| Error code: | H1-1353 |
| Display: | Input System Failure #H1-1353 : Pull Tray 3 out and insert it. |
| Description: | Input System Failure #H1-1353 : Pull Tray 3 out and insert it. |
| Causes: | The paper is not fed from tray3. |
| Remedy: | 1) Remove and insert tray3 correctly. 2) Turn the machine off then on. 3) If the problem persists, turn the machine off. 4) Remove the Bracket Rear Cover after removing 5 screws. 5) Check if the connection between the DCF pick up drive and DCF board is correct. 6) If the connection is OK, replace the pick up drive unit(JC93-00442A). 7) If the problem persists, check the following. a) Remove the DCF pick up unit1. b) Check if the photo sensor in the DCF pick up unit1 is contaminated, clean it. c) If the photo sensor(0604-001393) is defective, replace it. |
| Error code: | H1-1411, H1-1412 |
| Description: | Paper jam in Tray 4. |
| Causes: | Paper jam has occurred in tray4. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.) |
| Remedy: | 1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray4. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray4. 3) If this jam error occurs frequently, check the rollers below. a) Remove tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit2. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit2. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit2. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit2(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A). |
| Error code: | H1-1417, H1-1418 |
| Display: | Paper jam in Tray 4. |
| Description: | Paper jam in Tray 4. |
| Causes: | Paper jam has occurred in tray4. (Pick up unit connection is defective. / Pickup rollers are defective. / Feed sensor is defective.) |
| Remedy: | 1) Open the DCF Take Away-Cover. Remove the jammed paper. 2) Remove tray4. Remove the jammed paper. Close the DCF Take Away-Cover and insert tray4. 3) If this jam error occurs frequently, check the rollers below. a) Remove tray3 and tray4. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93-00540A). 4) If pick up/ reverse/ forward rollers have no problem, check the following. a) Remove the DCF pick up unit2. Check if the feed sensor cable is connected correctly. b) Check if the sensor cable on DCF board is connected correctly. c) If the connection is OK, replace the feed sensor(0604-001381). d) Install the DCF pick up unit2. 5) If the problem persists after checking step 3~4, check the following : a) Remove the DCF pick up unit2. Check if the sensor and actuator are assembled correctly. b) When pushing the pickup lever, check if the pick up rollers are down. c) Replace the DCF pick up unit2(JC93-00513A) or defective part. 6) Check the DCF feed motor. a) Check if the DCF feed motor cable is connected correctly. b) If the connection is OK, replace the DCF feed drive unit(JC93-00447A). 7) Check the DCF pick up motor. a) Check if the DCF pick up motor cable is connected correctly. b) If the connection is OK, replace the DCF pick up drive unit(JC93-00442A). |
| Error code: | H1-1422 |
| Display: | Tray 4 cassette is pulled out. Insert it properly. |
| Description: | Tray 4 cassette is pulled out. Insert it properly. |
| Causes: | Tray 4 is pulled out or the auto size sensor connector is not connected or is broken. |
| Remedy: | 1) Remove and insert tray4 correctly. 2) If the problem persists, remove tray3 and tray4. Look inside machine. 3) Check if the auto size sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the auto size sensor(JC93-00018A). 5) If the problem persists, replace the DCF board(JC92-02453A). |
| Error code: | H1-1451, H1-1452, H1-1454 |
| Display: | Paper is low in Tray 4. Load paper. Paper is empty in tray 4. Load paper. |
| Description: | Paper is low in Tray 4. Load paper. Paper is empty in Tray 4. Load paper. |
| Causes: | Paper in tray4 is less than 10%. / The photo sensor is defective. |
| Remedy: | 1) Remove tray4. Load the paper in tray4. 2) If paper is loaded but error message has not disappeared, check the following. a) Remove the DCF pick up unit2. b) Check if the photo sensor in the DCF pick up unit2 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. d) If the actuator(JC66-03199A) is defective, replace it. |
| Error code: | H1-1453 |
| Display: | Input System Failure #H1-1453 : Pull Tray 4 out and insert it. |
| Description: | Input System Failure #H1-1453 : Pull Tray 4 out and insert it. |
| Causes: | The paper is not fed from tray4. |
| Remedy: | 1) Remove and insert tray4 correctly. 2) Turn the machine off then on. 3) If the problem persists, turn the machine off. 4) Remove the Bracket Rear Cover after removing 5 screws. 5) Check if the connection between the DCF pick up drive and DCF board is correct. 6) If the connection is OK, replace the pick up drive unit(JC93-00442A). 7) If the problem persists, check the following. a) Remove the DCF pick up unit2. b) Check if the photo sensor in the DCF pick up unit2 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. |
| Error code: | H1-5323 |
| Display: | Tray door is open. Close the door |
| Description: | Tray door is open. Close the door |
| Causes: | DCF Takeaway-Cover is open. / I/L-Switch harness or connector is defective. |
| Remedy: | 1) Open and close the DCF Take away-Cover correctly. 2) If the problem persists, check the following. a) Check if I/L-Switch(HARNESS-DCF COVER OPEN)(JC39–01696A) is not operating normally. If it is defective, replace it. b) If the I/L Switch is OK, replace the DCF board(JC92–02453A). |
| Error code: | H1-5330 |
| Display: | DCF Failure #H1-5330. Check internal DCF connection. |
| Description: | DCF Failure #H1-5330. Check internal DCF connection. |
| Causes: | A communication error between the optional tray and the main machine has occurred. |
| Remedy: | 1) Lift up and release the DCF unit from the machine. 2) Remove the Bracket Rear Cover after removing 5 screws. 3) Check if the interface connector is connected to the DCF board. If the interface connector(JC39–01690A) is defective, replace it. 4) If the problem persists, replace the DCF board. |
| Error code: | H2-6144 |
| Description: | Finisher is pulled out. Insert it properly |
| Causes: | Finisher is pulled out. / Finisher is not installed correctly. |
| Remedy: | 1) Check if the finisher cable is connected to the copier. 2) Remove and reinstall the finisher. 3) If the problem persists, replace the finisher main board. |
| Error code: | H2-6211, H2-6212 |
| Description: | Finisher Failure: #H2-621x. Check finisher. Call for service if the problem persists |
| Causes: | Ejector1 failed to leave home position during initializing. (H2-6211) Ejector1 failed to reach home position during initializing. (H2-6212) Ejector1 failed to leave home position during printing job. (H2-6213) Ejector1 failed to reach home position during printing job. (H2-6214) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below : 2) Does finisher Ejector1 Assembly work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Remove the cover. d) Disassemble related parts. e) Check the sensor position and harness condition. f) Check sensor plug and encoder condition. 3) Does finisher Ejector1 gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set. 4) Does finisher Ejector1 motor work well? a) Check the Ejector 1 motor belt. b) Replace Ejector 1 Motor. |
| Error code: | H2-6213, H2-6214 |
| Description: | Finisher Failure: #H2-621x. Check finisher. Call for service if the problem persists |
| Causes: | Ejector1 failed to leave home position during initializing. (H2-6211) Ejector1 failed to reach home position during initializing. (H2-6212) Ejector1 failed to leave home position during printing job. (H2-6213) Ejector1 failed to reach home position during printing job. (H2-6214) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below : 2) Does finisher Ejector1 Assembly work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Remove the cover. d) Disassemble related parts. e) Check the sensor position and harness condition. f) Check sensor plug and encoder condition. 3) Does finisher Ejector1 gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set. 4) Does finisher Ejector1 motor work well? a) Check the Ejector 1 motor belt. b) Replace Ejector 1 Motor. |
| Error code: | H2-6221, H2-6222 |
| Description: | Finisher Failure: #H2-622x. Check finisher. Call for service if the problem persists |
| Causes: | Ejector2 failed to leave home position during initializing. (H2-6221) Ejector2 failed to reach home position during initializing. (H2-6222) Ejector2 failed to leave home position during printing job. (H2-6223) Ejector2 failed to reach home position during printing job. (H2-6224) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does finisher Ejector2 Assembly work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Cover Remove. d) Disassemble related parts. e) Check the sensor position and harness condition. f) Check sensor plug and encoder condition. 3) Does finisher Ejector2 gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set. (JC66-04236A / JC66-04518A) 4) Does finisher Ejector2 motor work well? a) Check the Ejector 2 motor belt (6602-003636). b) Replace Ejector2 Motor (JC90-01335A). |
| Error code: | H2-6223, H2-6224 |
| Description: | Finisher Failure: #H2-622x. Check finisher. Call for service if the problem persists |
| Causes: | Ejector2 failed to leave home position during initializing. (H2-6221) Ejector2 failed to reach home position during initializing. (H2-6222) Ejector2 failed to leave home position during printing job. (H2-6223) Ejector2 failed to reach home position during printing job. (H2-6224) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does finisher Ejector2 Assembly work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Cover Remove. d) Disassemble related parts. e) Check the sensor position and harness condition. f) Check sensor plug and encoder condition. 3) Does finisher Ejector2 gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set. (JC66-04236A / JC66-04518A) 4) Does finisher Ejector2 motor work well? a) Check the Ejector 2 motor belt (6602-003636). b) Replace Ejector2 Motor (JC90-01335A). |
| Error code: | H2-6231, H2-6232 |
| Description: | Finisher Failure: #H2-623x. Check finisher. Call for service if the problem persists |
| Causes: | Paper Holding Lever failed to leave home position during initializing. (H2-6231) Paper Holding Lever failed to reach home position during initializing.(H2-6232) Paper Holding Lever failed to leave home position during printing. (H2-6233) Paper Holding Lever failed to reach home position during printing. (H2-6234) |
| Remedy: | 1) If there is jammed paper on the path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Paper Holding Lever still doesn’t go back to home position and error does not disappear, follow the instructions below : 2) Does finisher input sensor (Standby & Home sensor) work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Replace the finisher input sensor. d) Replace the finisher main board. 3) Does finisher Paper Holding Lever work well? a) Make sure finisher Paper Holding Lever cable is connected well to the Solenoid connector. b) Make sure finisher Paper Holding Lever cable is connected well to the main board connector. c) Check the Paper Holding Lever Solenoid. If you need, replace the solenoid. d) Check the paper holder return spring. If you need, replace the spring(JC61-07269A). 4) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6233, H2-6234 |
| Description: | Finisher Failure: #H2-623x. Check finisher. Call for service if the problem persists |
| Causes: | Paper Holding Lever failed to leave home position during initializing. (H2-6231) Paper Holding Lever failed to reach home position during initializing.(H2-6232) Paper Holding Lever failed to leave home position during printing. (H2-6233) Paper Holding Lever failed to reach home position during printing. (H2-6234) |
| Remedy: | 1) If there is jammed paper on the path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Paper Holding Lever still doesn’t go back to home position and error does not disappear, follow the instructions below : 2) Does finisher input sensor (Standby & Home sensor) work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Replace the finisher input sensor. d) Replace the finisher main board. 3) Does finisher Paper Holding Lever work well? a) Make sure finisher Paper Holding Lever cable is connected well to the Solenoid connector. b) Make sure finisher Paper Holding Lever cable is connected well to the main board connector. c) Check the Paper Holding Lever Solenoid. If you need, replace the solenoid. d) Check the paper holder return spring. If you need, replace the spring(JC61-07269A). 4) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6241, H2-6242 |
| Description: | Finisher Failure: #H2-624x. Check finisher. Call for service if the problem persists |
| Causes: | Paper Support failed to leave home during initializing. (H2-6241) Paper Support failed to reach home during initializing. (H2-6242) Paper Support failed to leave home during printing. (H2-6243) Paper Support failed to reach home during printing. (H2-6244) |
| Remedy: | 1) If there is jammed paper on the path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Paper Support still doesn’t go back to home position and error does not disappear, follow the instructions below : 2) Does paper support interrupt sensor work well? a) Make sure interrupt sensor cable is connected well to the sensor connector. b) Make sure interrupt sensor cable is connected well to the main board connector. c) Check the paper support’s sensor plug. d) If you need, replace the interrupt sensor. 3) Does finisher Paper Support motor gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set 4) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6243, H2-6244 |
| Description: | Finisher Failure: #H2-624x. Check finisher. Call for service if the problem persists |
| Causes: | Paper Support failed to leave home during initializing. (H2-6241) Paper Support failed to reach home during initializing. (H2-6242) Paper Support failed to leave home during printing. (H2-6243) Paper Support failed to reach home during printing. (H2-6244) |
| Remedy: | 1) If there is jammed paper on the path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Paper Support still doesn’t go back to home position and error does not disappear, follow the instructions below : 2) Does paper support interrupt sensor work well? a) Make sure interrupt sensor cable is connected well to the sensor connector. b) Make sure interrupt sensor cable is connected well to the main board connector. c) Check the paper support’s sensor plug. d) If you need, replace the interrupt sensor. 3) Does finisher Paper Support motor gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set 4) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6311 |
| Description: | Finisher Failure: #H2-6311. Check finisher. Call for service if the problem persists |
| Causes: | Stapler failed to return home position after stapling. |
| Remedy: | 1) If there is jammed paper on the stapler, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If stapler still doesn’t go back to home position and error does not disappear, follow the instructions below : 2) Does finisher stapler cartridge can be pulled out? a) Rotate stapler gear manually to move stapler head back to home (top) position. b) Clear staple that is not stapling out completely from stapler cartridge. c) Clear staple that is existed inside stapler. d) Stapler cover or Jam cover open and close.( It’s the Finisher Initializing) 3) Does finisher stapler input sensor work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Replace the finisher stapler(JC81-07917A). d) Replace the finisher main board. 4) Does finisher stapler motor work well? a) Make sure finisher stapler motor cable is connected well to the stapler motor connector. b) Make sure finisher stapler motor cable is connected well to the main board connector. c) Replace the finisher stapler. (JC81-07917A) d) Replace the finisher main board. 5) Check if any debris(staple) existed. Please make sure to remove any debris. |
| Error code: | H2-6321, H2-6322, H2-6323 |
| Description: | Finisher Failure: #H2-63xx. Check finisher. Call for service if the problem persists |
| Causes: | Stapler Traverse failed to leave front home position during initializing. (H2-6321) Stapler Traverse failed to reach front home position during initializing. (H2-6322) Stapler Traverse failed to leave front home position during printing. (H2-6323) Stapler Traverse failed to reach front home position during printing. (H2-6324) Stapler Traverse failed to leave rear home position during initializing. (H2-6331) Stapler Traverse failed to reach rear home position during initializing. (H2-6332) Stapler Traverse failed to leave rear home position during printing. (H2-6333) Stapler Traverse failed to reach rear home position during printing. (H2-6334) |
| Remedy: | 1) If there is jammed paper on the path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Stapler traverse still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does traverse interrupt sensor (Standby & Home sensor) work well? a) Does traverse interrupt sensor (Standby & Home sensor) work well? i) Make sure finisher input sensor cable is connected well to the sensor connector. ii) Make sure finisher input sensor cable is connected well to the main board connector. iii) Replace the finisher input sensor. iv) Replace the finisher main board. b) Does finisher Stapler traverse work well? i) Make sure Stapler traverse cable is connected well to the Motor connector. ii) Make sure finisher Stapler traverse cable is connected well to the main board connector. iii) Make sure the belt is tight on the correct position, if it has the belt. iv) Make sure gear set. If you can see the broken gear, replace the gear. v) Check the traverse motor, If you need, replace the stapler traverse motor. c) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6324, H2-6331, H2-6332 |
| Description: | Finisher Failure: #H2-63xx. Check finisher. Call for service if the problem persists |
| Causes: | Stapler Traverse failed to leave front home position during initializing. (H2-6321) Stapler Traverse failed to reach front home position during initializing. (H2-6322) Stapler Traverse failed to leave front home position during printing. (H2-6323) Stapler Traverse failed to reach front home position during printing. (H2-6324) Stapler Traverse failed to leave rear home position during initializing. (H2-6331) Stapler Traverse failed to reach rear home position during initializing. (H2-6332) Stapler Traverse failed to leave rear home position during printing. (H2-6333) Stapler Traverse failed to reach rear home position during printing. (H2-6334) |
| Remedy: | 1) If there is jammed paper on the path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Stapler traverse still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does traverse interrupt sensor (Standby & Home sensor) work well? a) Does traverse interrupt sensor (Standby & Home sensor) work well? i) Make sure finisher input sensor cable is connected well to the sensor connector. ii) Make sure finisher input sensor cable is connected well to the main board connector. iii) Replace the finisher input sensor. iv) Replace the finisher main board. b) Does finisher Stapler traverse work well? i) Make sure Stapler traverse cable is connected well to the Motor connector. ii) Make sure finisher Stapler traverse cable is connected well to the main board connector. iii) Make sure the belt is tight on the correct position, if it has the belt. iv) Make sure gear set. If you can see the broken gear, replace the gear. v) Check the traverse motor, If you need, replace the stapler traverse motor. c) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6333, H2-6334 |
| Description: | Finisher Failure: #H2-63xx. Check finisher. Call for service if the problem persists |
| Causes: | Stapler Traverse failed to leave front home position during initializing. (H2-6321) Stapler Traverse failed to reach front home position during initializing. (H2-6322) Stapler Traverse failed to leave front home position during printing. (H2-6323) Stapler Traverse failed to reach front home position during printing. (H2-6324) Stapler Traverse failed to leave rear home position during initializing. (H2-6331) Stapler Traverse failed to reach rear home position during initializing. (H2-6332) Stapler Traverse failed to leave rear home position during printing. (H2-6333) Stapler Traverse failed to reach rear home position during printing. (H2-6334) |
| Remedy: | 1) If there is jammed paper on the path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Stapler traverse still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does traverse interrupt sensor (Standby & Home sensor) work well? a) Does traverse interrupt sensor (Standby & Home sensor) work well? i) Make sure finisher input sensor cable is connected well to the sensor connector. ii) Make sure finisher input sensor cable is connected well to the main board connector. iii) Replace the finisher input sensor. iv) Replace the finisher main board. b) Does finisher Stapler traverse work well? i) Make sure Stapler traverse cable is connected well to the Motor connector. ii) Make sure finisher Stapler traverse cable is connected well to the main board connector. iii) Make sure the belt is tight on the correct position, if it has the belt. iv) Make sure gear set. If you can see the broken gear, replace the gear. v) Check the traverse motor, If you need, replace the stapler traverse motor. c) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6411 |
| Description: | Finisher Failure: #H2-6411. Check finisher. Call for service if the problem persists |
| Causes: | Punch unit failed to return home position after punching job. |
| Remedy: | 1) If there is jammed paper on the path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If punch hopper still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does finisher Punch work well? a) Clear Hole Punch Hopper b) Stapler cover or Jam cover open and close.( It’s the Finisher Initializing) c) If fault persists, power Off/Power On. d) If necessary, replace the punch unit. 3) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6421, H2-6422 |
| Description: | Finisher Failure: #H2-64xx. Check finisher. Call for service if the problem persists |
| Causes: | Punch unit failed to leave home position during initializing. (H2-6421) Punch unit failed to reach home position during initializing. (H2-6422) Punch unit failed to leave home position during printing. (H2-6423) Punch unit failed to reach home position during printing. (H2-6424) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If punch still doesn’t go back to home position and error does not disappear, follow the instructions below : 2) Does punch interrupt sensor work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Check the punch interrupt sensor position. d) Check the punch motor’s encoder position. e) If the punch does not move, change the punch module. 3) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6423, H2-6424 |
| Description: | Finisher Failure: #H2-64xx. Check finisher. Call for service if the problem persists |
| Causes: | Punch unit failed to leave home position during initializing. (H2-6421) Punch unit failed to reach home position during initializing. (H2-6422) Punch unit failed to leave home position during printing. (H2-6423) Punch unit failed to reach home position during printing. (H2-6424) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If punch still doesn’t go back to home position and error does not disappear, follow the instructions below : 2) Does punch interrupt sensor work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Check the punch interrupt sensor position. d) Check the punch motor’s encoder position. e) If the punch does not move, change the punch module. 3) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6440, H2-6452 |
| Description: | Hole punch hopper is not installed. Install hopper. Hole punch hopper is full. Remove waste of hopper. |
| Causes: | Hole punch hopper is not installed correctly. (H2-6440) Hole punch hopper is full. (H2-6452) |
| Remedy: | 1) If punch dust box is full, removing dust manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If error does not disappear, follow the instructions below : 2) Does punch interrupt sensor work well? a) Make sure hopper’s sensor cable is connected well to the sensor connector. b) Make sure hopper’s sensor cable is connected well to the main board connector. c) Check the interrupt sensor position. d) Check the hopper’s plug position. 3) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6511, H2-6512 |
| Description: | Finisher Failure: #H2-651x. Check finisher. Call for service if the problem persists |
| Causes: | Stacker Motor fault has occurred during initializing. (H2-6511) Stacker Motor Fault has occurred during printing. (H2-6512) |
| Remedy: | 1) If there is jammed paper on the Main Tray, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Main Tray still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does main tray position sensor work well? a) Make sure main tray position sensor cable is connected well to the sensor connector. b) Make sure main tray position sensor cable is connected well to the main board connector. c) Check the main tray position sensor. d) Check the finisher main board. 3) Does finisher Main Tray motor(Stacker motor) work well? a) Make sure finisher Main Tray motor cable is connected well to the motor connector. b) Make sure finisher Main Tray motor cable is connected well to the main board connector. c) Replace the finisher Main Tray motor. d) If you need, replace the finisher main board. 4) Does finisher Main Tray motor gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set. (JC81-07637A / JC81-07636A) 5) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6531, H2-6532 |
| Description: | Finisher Failure: #H2-653x. Check finisher. Call for service if the problem persists |
| Causes: | Ejector2 motor does not work during Initializing. (H2-6531) Ejector2 motor does not work during printing. (H2-6532) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does finisher Ejector2 Assemble work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Remove the cover. d) Disassemble related parts. e) Check the sensor position and harness condition. f) Check sensor plug and encoder condition. 3) Does finisher Ejector2 gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set (JC66-04236A / JC66-04518A) 4) Does finisher Ejector2 motor work well? a) Check the Ejector 2 motor belt. (6602-003636) b) Replace Ejector2 motor. (JC90-01335A) 5) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6551, H2-6552 |
| Description: | Finisher Failure: #H2-655x. Check finisher. Call for service if the problem persists |
| Causes: | Punch motor does not work during Initializing. (H2-6551) Punch motor does not work during printing. (H2-6552). |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If punch still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does punch interrupt sensor work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Check the punch interrupt sensor position. d) Check the punch motor’s encoder position. e) If the punch does not move, change the punch module. 3) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6700, H2-6701, H2-6702 |
| Description: | Paper jam in front of finisher Paper jam inside of finisher Paper jam at exit of finisher |
| Causes: | Sheet’s lead edge failed to pass entrance position. (H2-6700) Sheet’s tail edge failed to pass entrance position. (H2-6701) Jam Is not cleared on entrance sensor during initializing. (H2-6702) Sheet failed to reach finisher Passthrough sensor. (H2-6703) Sheet failed to pass finisher Passthrough sensor. (H2-6704) Jam Is not cleared on Passthrough sensor during initializing. (H2-6705) |
| Remedy: | 1) Open finisher jam cover, and make sure that the paper is on the paper path. If there is paper, removing paper manually. If the error does not disappear even after removing paper and closing finisher jam door, follow the instructions below: 2) Does finisher input sensor work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Replace the finisher input sensor. (0604-001381 / 0604-001415) d) Replace the finisher main board. (JC92-02774A) 3) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6703, H2-6704, H2-6705 |
| Description: | Paper jam in front of finisher Paper jam inside of finisher Paper jam at exit of finisher |
| Causes: | Sheet failed to reach finisher Passthrough sensor. (H2-6703) Sheet failed to pass finisher Passthrough sensor. (H2-6704) Jam Is not cleared on Passthrough sensor during initializing. (H2-6705) |
| Remedy: | 1) Open finisher jam cover, and make sure that the paper is on the paper path. If there is paper, removing paper manually. If the error does not disappear even after removing paper and closing finisher jam door, follow the instructions below 2) Does finisher input sensor work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Replace the finisher input sensor. (0604-001381 / 0604-001415) d) Replace the finisher main board. (JC92-02774A) 3) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6706 |
| Display: | Finisher Failure: #H2-6706. Check finisher |
| Description: | Finisher Failure: #H2-6706. Check finisher |
| Causes: | Transport motor does not work during Initializing. |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does the transport motor work well? a) Make sure transport motor cable is connected well to the motor connector. b) Make sure transport motor cable is connected well to the finisher main board. c) Replace the transport motor. d) Replace the finisher main board. |
| Error code: | H2-6707, H2-6708 |
| Description: | Finisher Failure: #H2-67xx. Check finisher |
| Causes: | Paddle unit failed to leave home position during initializing. (H2-6707) Paddle unit failed to reach home position during initializing. (H2-6708) Paddle unit failed to leave home position during printing. (H2-6709) Paddle unit failed to reach home position during printing. (H2-6710) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does the paddle home sensor work well? a) Make sure the paddle home sensor cable is connected well to the sensor connector. b) Make sure the paddle home sensor cable is connected well to the main board connector. c) Check the paddle home sensor. d) Check the actuator home paddle. e) If necessary, replace the finisher main board. 3) Does the main paddle motor work well? a) Make sure the main paddle motor cable is connected well to the motor connector. b) Make sure the main paddle motor cable is connected well to the main board connector. c) Replace the main paddle motor. |
| Error code: | H2-6709, H2-6710 |
| Description: | Finisher Failure: #H2-67xx. Check finisher |
| Causes: | Paddle unit failed to leave home position during initializing. (H2-6707) Paddle unit failed to reach home position during initializing. (H2-6708) Paddle unit failed to leave home position during printing. (H2-6709) Paddle unit failed to reach home position during printing. (H2-6710) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does the paddle home sensor work well? a) Make sure the paddle home sensor cable is connected well to the sensor connector. b) Make sure the paddle home sensor cable is connected well to the main board connector. c) Check the paddle home sensor. d) Check the actuator home paddle. e) If necessary, replace the finisher main board. 3) Does the main paddle motor work well? a) Make sure the main paddle motor cable is connected well to the motor connector. b) Make sure the main paddle motor cable is connected well to the main board connector. c) Replace the main paddle motor. |
| Error code: | H2-6711, H2-6712 |
| Description: | Finisher Failure: #H2-67xx. Check finisher. |
| Causes: | Ejector unit failed to leave home position during initializing. (H2-6711) Ejector unit failed to reach home position during initializing. (H2-6712) Ejector unit failed to leave home position during printing. (H2-6713) Ejector unit failed to reach home position during printing. (H2-6714) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does the eject 1,2 motor work well? a) Make sure the eject 1,2 motor cable is connected well to the motor connector. b) Make sure the eject 1,2 motor cable is connected well to the main board connector. c) Replace the eject 1,2 motor. (JC31-00009C / JC90-01335A) d) Replace the finisher main board. 3) Does the Eject-sub Assy component parts work well? a) Make sure component parts can move or rotate smoothly. b) Make sure there is no any mechanical interference to stop moving or rotating. c) Make sure the belt is tight on the correct position, if it has the belt. d) Make sure each gear is not broken. e) Check home position sensor. f) Replace the Eject-sub Assy. |
| Error code: | H2-6713, H2-6714 |
| Description: | Finisher Failure: #H2-67xx. Check finisher. |
| Causes: | Ejector unit failed to leave home position during initializing. (H2-6711) Ejector unit failed to reach home position during initializing. (H2-6712) Ejector unit failed to leave home position during printing. (H2-6713) Ejector unit failed to reach home position during printing. (H2-6714) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does the eject 1,2 motor work well? a) Make sure the eject 1,2 motor cable is connected well to the motor connector. b) Make sure the eject 1,2 motor cable is connected well to the main board connector. c) Replace the eject 1,2 motor. (JC31-00009C / JC90-01335A) d) Replace the finisher main board. 3) Does the Eject-sub Assy component parts work well? a) Make sure component parts can move or rotate smoothly. b) Make sure there is no any mechanical interference to stop moving or rotating. c) Make sure the belt is tight on the correct position, if it has the belt. d) Make sure each gear is not broken. e) Check home position sensor. f) Replace the Eject-sub Assy. |
| Error code: | H2-6715, H2-6716 |
| Description: | Finisher Failure: #H2-67xx. Check finisher |
| Causes: | Rear tamper unit failed to leave home position during initializing. (H2-6715) Rear tamper unit failed to reach home position during initializing. (H2-6716) Rear tamper unit failed to leave home position during printing. (H2-6717) Rear tamper unit failed to reach home position during printing. (H2-6718) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does the rear jogger home sensor work well? a) Make sure the sensor harness is connected well to the rear jogger home sensor. b) Make sure the sensor harness is connected well to the finisher main board. c) Replace the rear jogger home sensor. d) Replace the finisher main board. 3) Does the rear jogger motor work well? a) Make sure the rear jogger motor cable is connected well to the motor connector. b) Make sure the rear jogger motor cable is connected well to the finisher main board. c) Replace the rear jogger motor. d) Replace the finisher main board. |
| Error code: | H2-6717, H2-6718 |
| Description: | Finisher Failure: #H2-67xx. Check finisher |
| Causes: | Rear tamper unit failed to leave home position during initializing. (H2-6715) Rear tamper unit failed to reach home position during initializing. (H2-6716) Rear tamper unit failed to leave home position during printing. (H2-6717) Rear tamper unit failed to reach home position during printing. (H2-6718) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does the rear jogger home sensor work well? a) Make sure the sensor harness is connected well to the rear jogger home sensor. b) Make sure the sensor harness is connected well to the finisher main board. c) Replace the rear jogger home sensor. d) Replace the finisher main board. 3) Does the rear jogger motor work well? a) Make sure the rear jogger motor cable is connected well to the motor connector. b) Make sure the rear jogger motor cable is connected well to the finisher main board. c) Replace the rear jogger motor. d) Replace the finisher main board. |
| Error code: | H2-6719, H2-6720 |
| Description: | Finisher Failure: #H2-67xx. Check finisher |
| Causes: | Front tamper unit failed to leave home position during initializing. (H2-6719) Front tamper unit failed to reach home position during initializing. (H2-6720) Front tamper unit failed to leave home position during printing. (H2-6721) Front tamper unit failed to reach home position during printing. (H2-6722) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does the front jogger home sensor work well? a) Make sure the sensor harness is connected well to the front jogger home sensor. b) Make sure the sensor harness is connected well to the finisher main board. c) Replace the front jogger home sensor. d) Replace the finisher main board. 3) Does the front jogger motor work well? a) Make sure the front jogger motor cable is connected well to the motor connector. b) Make sure the front jogger motor cable is connected well to the finisher main board. c) Replace the front jogger motor. d) Replace the finisher main board. |
| Error code: | H2-6721, H2-6722 |
| Description: | Finisher Failure: #H2-67xx. Check finisher |
| Causes: | Front tamper unit failed to leave home position during initializing. (H2-6719) Front tamper unit failed to reach home position during initializing. (H2-6720) Front tamper unit failed to leave home position during printing. (H2-6721) Front tamper unit failed to reach home position during printing. (H2-6722) |
| Remedy: | 1) If there is jammed paper on the paper path, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If component still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does the front jogger home sensor work well? a) Make sure the sensor harness is connected well to the front jogger home sensor. b) Make sure the sensor harness is connected well to the finisher main board. c) Replace the front jogger home sensor. d) Replace the finisher main board. 3) Does the front jogger motor work well? a) Make sure the front jogger motor cable is connected well to the motor connector. b) Make sure the front jogger motor cable is connected well to the finisher main board. c) Replace the front jogger motor. d) Replace the finisher main board. |
| Error code: | H2-6723 |
| Description: | Finisher Failure: #H2-6A63. Check finisher. |
| Causes: | Staple unit can not work stapling because paper is too thick. |
| Remedy: | 1) Check the paper specification for stapling. If it is not proper, replace the paper. 2) Check the staple unit. If necessary, replace it. |
| Error code: | H2-6724, H2-6725 |
| Description: | Finisher Failure: #H2-672x. Check finisher. |
| Causes: | Paper can not be moved to stapling position. |
| Remedy: | 1) Remove and reassemble the staple unit. 2) Check the staple unit. If necessary, replace it. |
| Error code: | H2-6726, H2-6727 |
| Display: | Finisher Stapler door is open. Close it. Finisher Jam door is open. Close it. |
| Description: | Finisher Stapler door is open. Close it Finisher Top door is open. Close it |
| Causes: | Finisher door is not closed. |
| Remedy: | 1) Close door to do finisher initialization. If error does not disappear, follow the instructions below : 2) Does finisher door cover can close well? a) The finisher door cover itself can be closed well. b) The both of the finisher door covers can push door open sensor switch well. c) The finisher door open sensor switch can be pushed well. d) Replace finisher cover door or switch. 3) Does finisher input sensor work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Replace the finisher input sensor(JC90-01301A). d) Replace the finisher main board(JC92-02774A). |
| Error code: | H2-6728, H2-6729 |
| Description: | Finisher Failure: #H2-67xx. Check finisher. |
| Causes: | Stapler failed to leave home position during Stapling. (H2-6728) Stapler failed to reach home position during Stapling. (H2-6729) Stapler failed to leave home position during Self-Priming. (H2-6730) Stapler failed to reach home position during Self-Priming. (H2-6731) |
| Remedy: | 1) If there is jammed paper on the stapler, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If stapler still doesn’t go back to home position and error does not disappear, follow the instructions below : 2) Does finisher stapler move well? a) Make sure stapler moving motor cable is connected well to the stapler motor connector. b) Make sure stapler moving motor cable is connected well to the main board connector. c) Check the sensor position and harness condition. d) Check the sensor plug or encoder condition. 3) Does finisher stapler’s gear set move well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) If you need, replace the stapler assembly. 4) Check if any debris(staple) existed. Please make sure to remove any debris. |
| Error code: | H2-6730, H2-6731 |
| Description: | Finisher Failure: #H2-67xx. Check finisher. |
| Causes: | Stapler failed to leave home position during Stapling. (H2-6728) Stapler failed to reach home position during Stapling. (H2-6729) Stapler failed to leave home position during Self-Priming. (H2-6730) Stapler failed to reach home position during Self-Priming. (H2-6731) |
| Remedy: | 1) If there is jammed paper on the stapler, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If stapler still doesn’t go back to home position and error does not disappear, follow the instructions below : 2) Does finisher stapler move well? a) Make sure stapler moving motor cable is connected well to the stapler motor connector. b) Make sure stapler moving motor cable is connected well to the main board connector. c) Check the sensor position and harness condition. d) Check the sensor plug or encoder condition. 3) Does finisher stapler’s gear set move well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) If you need, replace the stapler assembly. 4) Check if any debris(staple) existed. Please make sure to remove any debris. |
| Error code: | H2-6732, H2-6733 |
| Display: | Staple cartridge is low. Replace it. Staple cartridge is empty. Replace it. |
| Description: | Staple cartridge is low. Replace it. Staple cartridge is empty. Replace it. |
| Causes: | Finisher stapler cartridge is necessary to refill. |
| Remedy: | 1) Open finisher stapler door to refill cartridge and then close door. Self-Priming will be executed automatically if necessary. If stapler error or warning does not disappear, follow the instructions below : 2) Does finisher stapler cartridge refill box equip well? a) Make sure stapler refill box equip well into cartridge. (JC81-07408A) b) Make sure staples doesn’t jam near stapler head. 3) Does finisher stapler input sensor work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Replace the finisher stapler(JC81-07917A). d) Replace the finisher main board. |
| Error code: | H2-6734 |
| Display: | Finisher Failure: #H2-6734. Check finisher |
| Description: | Finisher Failure: #H2-6734. Check finisher |
| Causes: | Stapler initialization is failed. |
| Remedy: | 1) Remove and reassemble the staple unit. 2) If necessary, replace the staple unit. 3) If necessary, replace the finisher main board. |
| Error code: | H2-6735 |
| Display: | Too much paper in finisher stacker. Remove printed paper. |
| Description: | Too much paper in finisher stacker. Remove printed paper |
| Causes: | Finisher Top tray is full. |
| Remedy: | 1) Remove paper on the finisher main tray. Main tray will move downward and upward to clear stack full warning. If warning does not disappear, follow the instructions below : 2) Does Top tray limit sensor work well? a) Make sure Top tray limit sensor cable is connected well to the sensor connector. b) Make sure Top tray limit sensor cable is connected well to the main board connector. c) Check the tray limit actuator’s condition. (JC66-04200A) d) Replace the Top tray limit sensor(JC39-02178A). e) Replace the finisher main board. 3) Does finisher main tray motor work well? a) Make sure finisher top tray motor cable is connected well to the main tray motor connector. b) Make sure finisher top tray motor cable is connected well to the main board connector. c) Replace the finisher main tray motor. d) Replace the finisher main board. 4) Check if any debris(staple)existed. Please make sure to remove any debris. |
| Error code: | H2-6736, H2-6737 |
| Description: | Finisher Failure: #H2-67xx. Check finisher |
| Causes: | Main Tray failed to leave home sensor during initializing. (H2-6736) Main Tray failed to reach home sensor during initializing. (H2-6737) Main Tray failed to leave home sensor during printing. (H2-6738) Main Tray failed to reach home sensor during printing. (H2-6739) |
| Remedy: | 1) If there is jammed paper on the Main Tray, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Main Tray still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does tray limit sensor (Standby & Home sensor) work well? a) Make sure tray limit sensor cable is connected well to the sensor connector. b) Make sure tray limit sensor cable is connected well to the main board connector. c) Check the limit actuator condition. d) If you need, replace the limit sensor. 3) Does finisher Main Tray motor work well? a) Make sure finisher Main Tray motor cable is connected well to the motor connector. b) Make sure finisher Main Tray motor cable is connected well to the main board connector. c) Replace the finisher Main Tray motor. 4) Does finisher Main Tray parts work well? a) Make sure Main Tray parts can move or rotate smoothly. b) Make sure there is no any mechanical interference to stop moving or rotating. c) Make sure the belt is tight on the correct position, if it has the belt. 5) Does finisher Main Tray motor gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set. (JC81-07637A / JC81-07636A) 6) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6738, H2-6739 |
| Description: | Finisher Failure: #H2-67xx. Check finisher |
| Causes: | Main Tray failed to leave home sensor during initializing. (H2-6736) Main Tray failed to reach home sensor during initializing. (H2-6737) Main Tray failed to leave home sensor during printing. (H2-6738) Main Tray failed to reach home sensor during printing. (H2-6739) |
| Remedy: | 1) If there is jammed paper on the Main Tray, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Main Tray still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does tray limit sensor (Standby & Home sensor) work well? a) Make sure tray limit sensor cable is connected well to the sensor connector. b) Make sure tray limit sensor cable is connected well to the main board connector. c) Check the limit actuator condition. d) If you need, replace the limit sensor. 3) Does finisher Main Tray motor work well? a) Make sure finisher Main Tray motor cable is connected well to the motor connector. b) Make sure finisher Main Tray motor cable is connected well to the main board connector. c) Replace the finisher Main Tray motor. 4) Does finisher Main Tray parts work well? a) Make sure Main Tray parts can move or rotate smoothly. b) Make sure there is no any mechanical interference to stop moving or rotating. c) Make sure the belt is tight on the correct position, if it has the belt. 5) Does finisher Main Tray motor gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set. (JC81-07637A / JC81-07636A) 6) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6740, H2-6741 |
| Description: | Finisher Failure: #H2-67xx. Check finisher |
| Causes: | Main Tray failed to leave stacker height sensor during initializing. (H2-6740) Main Tray failed to reach stacker height sensor during initializing. (H2-6741) Main Tray failed to leave stacker height sensor during printing. (H2-6742) Main Tray failed to reach stacker height sensor during printing. (H2-6743) |
| Remedy: | 1) If there is jammed paper on the Main Tray, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Main Tray still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does finisher stacker height sensor work well? a) Make sure stacker height sensor cable is connected well to the sensor connector. b) Make sure stacker height sensor cable is connected well to the main board connector. c) Replace the stacker height sensor. d) Replace the finisher main board. 3) Does finisher Main Tray motor work well? a) Make sure finisher Main Tray motor cable is connected well to the motor connector. b) Make sure finisher Main Tray motor cable is connected well to the main board connector. c) Replace the finisher Main Tray motor. 4) Does finisher Main Tray parts work well? a) Make sure Main Tray parts can move or rotate smoothly. b) Make sure there is no any mechanical interference to stop moving or rotating. c) Make sure the belt is tight on the correct position, if it has the belt. 5) Does finisher Main Tray motor gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set. (JC81-07637A / JC81-07636A) 6) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6742, H2-6743 |
| Description: | Finisher Failure: #H2-67xx. Check finisher |
| Causes: | Main Tray failed to leave stacker height sensor during initializing. (H2-6740) Main Tray failed to reach stacker height sensor during initializing. (H2-6741) Main Tray failed to leave stacker height sensor during printing. (H2-6742) Main Tray failed to reach stacker height sensor during printing. (H2-6743) |
| Remedy: | 1) If there is jammed paper on the Main Tray, removing paper manually. Open and close finisher stapler door or jam cover to check if finisher executes initialization process. If Main Tray still doesn’t go back to home position and error does not disappear, follow the instructions below: 2) Does finisher stacker height sensor work well? a) Make sure stacker height sensor cable is connected well to the sensor connector. b) Make sure stacker height sensor cable is connected well to the main board connector. c) Replace the stacker height sensor. d) Replace the finisher main board. 3) Does finisher Main Tray motor work well? a) Make sure finisher Main Tray motor cable is connected well to the motor connector. b) Make sure finisher Main Tray motor cable is connected well to the main board connector. c) Replace the finisher Main Tray motor. 4) Does finisher Main Tray parts work well? a) Make sure Main Tray parts can move or rotate smoothly. b) Make sure there is no any mechanical interference to stop moving or rotating. c) Make sure the belt is tight on the correct position, if it has the belt. 5) Does finisher Main Tray motor gear set work well? a) Make sure gear set can rotate smoothly. b) Make sure each gear is not broken. c) Replace the gear set. (JC81-07637A / JC81-07636A) 6) Check if any debris existed. Please make sure to remove any debris. |
| Error code: | H2-6744 |
| Display: | Staple Cartridge not install. Install it. |
| Description: | Finisher Failure: #H2-6A63. Check finisher. |
| Causes: | Finisher stapler cartridge is not installed into stapler. |
| Remedy: | 1) Open finisher stapler door to put back cartridge into stapler and then close door. Self-Priming will be executed automatically if necessary. If stapler warning does not disappear, follow the instructions below : 2) Does finisher stapler input sensor work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Replace the finisher stapler cartridge. (JC81-07408A) d) Replace the finisher stapler. (JC81-07917A) e) Replace the finisher main board. 3) Check if any debris(staple)existed. Please make sure to remove any debris. |
| Error code: | H2-6A50 |
| Display: | Finisher Failure: #H2-6A50. Check finisher. |
| Description: | Finisher Failure: #H2-6A50. Check finisher |
| Causes: | Communication error with finisher |
| Remedy: | 1) Copier power off and power on. If the error does not disappear, follow the instructions below: 2) Does finisher work well? a) Make sure finisher interface cable is connected with main board. b) Replace the finisher main board. |
| Error code: | H2-6A63 |
| Display: | Finisher Failure: #H2-6A63. Check finisher. |
| Description: | Staple cartridge is empty. Replace it |
| Causes: | Finisher stapler cartridge is necessary to refill. |
| Remedy: | 1) Open finisher stapler door to refill cartridge and then close door. Self-Priming will be executed automatically if necessary. If stapler error or warning does not disappear, follow the instructions below : 2) Does finisher stapler cartridge refill box equip well? a) Make sure stapler refill box equip well into cartridge. (JC81-07408A) b) Make sure staples doesn’t jam near stapler head. 3) Does finisher stapler input sensor work well? a) Make sure finisher input sensor cable is connected well to the sensor connector. b) Make sure finisher input sensor cable is connected well to the main board connector. c) Replace the finisher stapler(JC81-07917A). d) Replace the finisher main board. |
| Error code: | M1-1113, M2-1121 |
| Display: | Paper jam in Tray 1. |
| Description: | Paper jam in Tray 1. |
| Causes: | Paper jam has occurred in tray1. |
| Remedy: | 1) Open the side cover and check if a foreign substance or paper is jammed inside the machine. 2) Remove tray1 and remove the jammed paper. 3) If this jam error occurs frequently, check the rollers of the pick up unit1. a) Remove tray1 and tray2. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93–00540A). 4) If the problem persists, check the pickup unit1 and feed sensor. a) Check if the pickup unit1 and feed sensor operate correctly. b) Check if the pickup unit1 harness is connected to the main board correctly. c) Check if the connector of the Guide-feed assembly is connected correctly. d) Check if the harness of pickup unit and feed sensor are connected correctly. 5) If the problem persists, check the pickup unit1. a) Remove the pickup unit and check the actuator and photo-sensor. b) Push the pickup-lever and check if it operates correctly. 6) If the problem persists, replace the pickup drive unit(JC93–00422A) or Pickup unit1(JC93-00511A). |
| Error code: | M1-1213, M2-1131 |
| Display: | Paper jam in Tray 2. |
| Description: | Paper jam in Tray 2. |
| Causes: | Paper jam has occurred in tray2. |
| Remedy: | 1) Open the side cover and check if a foreign substance or paper is jammed inside the machine. 2) Remove tray2 and remove the jammed paper. 3) If this jam error occurs frequently, check the rollers of the pick up unit1. a) Remove tray1 and tray2. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller(JC93–00540A). 4) If the problem persists, check the pickup unit2 and feed sensor. a) Check if the pickup unit2 and feed sensor operate correctly. b) Check if the pickup unit2 harness is connected to the main board correctly. c) Check if the connector of the Guide-feed assembly is connected correctly. d) Check if the harness of pickup unit and feed sensor are connected correctly. 5) If the problem persists, check the pickup unit2. a) Remove the pickup unit2 and check the actuator and photo-sensor. b) Push the pickup-lever and check if it operates correctly. 6) If the problem persists, replace the pickup drive unit2(JC93–00422A) or Pickup unit1(JC93-00512A). |
| Error code: | M1-1610 |
| Display: | Paper jam in MP Tray. |
| Description: | Paper Jamin MP tray |
| Causes: | The jammed paper has occurred in the MP tray. |
| Remedy: | 1) Remove the jammed paper. 2) If the jammed paper occurs continually, check the followings. a) Check if the pick up/forward/reverse roller are worn out or contaminated. Clean the contaminated part or replace it. b) Check if the actuator is assembled correctly. 3) If the pick up clutch is defective, replace it. 4) If the problem persists, replace the MP unit. |
| Error code: | M1-3122 |
| Display: | Tray 1 cassette is pulled out. Insert it properly. |
| Description: | Tray 1 cassette is pulled out. Insert it properly. |
| Causes: | Tray 1 is pulled out or the auto size sensor connector is not connected or broken. |
| Remedy: | 1) Remove and insert Tray1 correctly. 2) If Tray1 is not locked or pulled out without holding the locking lever, remove Tray1. 3) Check if foreign substance or paper is inside the space between Tray1,2. If so, please remove it. 4) If the problem persists, check that the auto size sensor is connected properly. 5) If the problem persists, replace the main board(JC92–02452A). |
| Error code: | M1-3222 |
| Display: | Tray 2 cassette is pulled out. Insert it properly. |
| Description: | Tray 2 cassette is pulled out. Insert it properly. |
| Causes: | Tray 2 is pulled out or the auto size sensor connector is not connected or broken. |
| Remedy: | 1) Remove and insert Tray2 correctly. 2) If Tray2 is not locked or pulled out without holding the locking lever, remove Tray2. 3) Check if foreign substance or paper is inside the space between Tray1,2. If so, please remove it. 4) If the problem persists, check that the auto size sensor is connected properly. 5) If the problem persists, replace the main board(JC92–02452A). |
| Error code: | M1-4111 |
| Display: | Input System Failure #M1-4111 : Pull Tray 1 out and insert it. |
| Description: | Input System Failure #M1–4111 : Pull Tray 1 out and insert it. |
| Causes: | The paper is not fed from tray1. |
| Remedy: | 1) Remove tray1 and re-install it. 2) If the problem persists, turn the machine off then on. 3) Enter SVC mode. Execute pickup motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100-0370) 4) If the pick up motor operation is abnormal, turn the machine off. 5) Remove the rear cover. 6) Check if the connection between pickup drive unit1 and main board is secure. 7) If the connection is OK, replace the pickup drive unit(JC93-00442A). 8) If the problem persists, check the pickup unit1. a) Check if the photo sensor in the pickup unit1 is defective. b) If the sensor(0604–001393) is defective, replace it. |
| Error code: | M1-4211 |
| Display: | Input System Failure #M1-4211 : Pull Tray 2 out and insert it. |
| Description: | Input System Failure #M1-4211 : Pull Tray 2 out and insert it. |
| Causes: | The paper is not fed from tray2. |
| Remedy: | 1) Remove tray2 and re-install it. 2) If the problem persists, turn the machine off then on. 3) Enter SVC mode. Execute pickup motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100-0380) 4) If the pick up motor operation is abnormal, turn the machine off. 5) Remove the rear cover. 6) Check if the connection between pickup drive unit2 and main board is secure. 7) If the connection is OK, replace the pickup drive unit(JC93-00442A). 8) If the problem persists, check the pickup unit2. a) Check if the photo sensor in the pickup unit2 is defective. b) If the sensor(0604–001393) is defective, replace it. |
| Error code: | M1-5111, M1-5112 |
| Display: | Paper is low in Tray 1. Load paper. Paper is empty in Tray 1. Load paper. |
| Description: | Paper is low in Tray 1. Load paper. Paper is empty in Tray 1. Load paper. |
| Causes: | Paper in the tray1 is less than 10%. / The photo sensor is defective. |
| Remedy: | 1) Remove tray 1. Load paper in the tray. And insert tray 1. 2) If paper is loaded but error message has not disappeared, check the following: a) Turn the machine off. Open the Side Cover. b) Remove Pick-Up Unit1. c) If the photo sensor is contaminated, clean it. d) If the photo sensor is defective, replace it(0604–001393). e) If the actuator is defective, replace it(JC66-03199A). |
| Error code: | M1-5113, M1-5120 |
| Description: | Paper is low in Tray 1. Load paper. Paper is empty in Tray 1. Load paper. |
| Causes: | Paper in the tray1 is less than 10%. / The photo sensor is defective. |
| Remedy: | 1) Remove tray 1. Load paper in the tray. And insert tray 1. 2) If paper is loaded but error message has not disappeared, check the following: a) Turn the machine off. Open the Side Cover. b) Remove Pick-Up Unit1. c) If the photo sensor is contaminated, clean it. d) If the photo sensor is defective, replace it(0604–001393). e) If the actuator is defective, replace it(JC66-03199A). |
| Error code: | M1-5211, M1-5212 |
| Display: | Paper is low in Tray 2. Load paper. Paper is empty in Tray 2. Load paper. |
| Description: | Paper is low in Tray 2. Load paper. Paper is empty in Tray 2. Load paper. |
| Causes: | Paper in the tray is less than 10% of specification. / The photo sensor is defective. |
| Remedy: | 1) Remove tray 2. Load paper in the tray, and insert the tray 2. 2) If paper is loaded but error message has not disappeared, check the following : a) Turn the machine off. Open the Side Cover. b) Remove Pick-Up Unit2. c) If the photo sensor is contaminated, clean it. d) If the photo sensor is defective, replace it(0604–001393). e) If the actuator is defective, replace it(JC66-03199A). |
| Error code: | M1-5612 |
| Display: | Paper is empty in MP Tray. Load paper. |
| Description: | Paper is empty in MP Tray. Load paper. |
| Causes: | Paper in the MP tray is less than 10%. / The photo sensor is defective. |
| Remedy: | 1) Load the paper in the MP tray. 2) If paper is loaded but error message has not disappeared, check the following : a) If the photo sensor is contaminated, clean it. b) If the photo sensor is defective, replace it(0604–001393). c) If the actuator is defective, replace it(JC66-03217A). |
| Error code: | M2-1124, M2-1125 |
| Display: | Paper jam inside of machine |
| Description: | Paper jam in tray 1 Paper jam inside of machine. |
| Causes: | Paper jam has occurred inside the machine. (Feed drive unit is defective / Feed 1 sensor is defective.) • M2–1124 : The leading edge of the paper has not reached the feed 1 sensor within the specified time. • M2-1125 : The paper has not left from the feed 1 sensor within the specified time. |
| Remedy: | 1) Open the side cover. Remove the jammed paper. 2) If jammed paper occurs continually, check the following. a) Enter SVC mode. Execute feed motor test. If the motor operation is normal, go to step d). b) Remove the rear cover. Check if the feed motor cable is connected correctly. c) If the connection is OK, replace the feed drive unit(JC93-00444A). d) If the feed motor operation is normal, check the feed 1 sensor. e) If the sensor operation is abnormal, check the harness. f) If the connection is OK, replace the feed sensor(0604-001381). |
| Error code: | M2-1134, M2-1135 |
| Display: | Paper jam inside of machine |
| Description: | Paper jam in tray 2 Paper jam in tray 1 |
| Causes: | Paper jam has occurred inside the machine. (Feed drive unit is defective / Feed 2 sensor is defective.) • M2–1134 : The leading edge of the paper has not reached the feed 2 sensor within the specified time. • M2-1135 : The paper has not left from the feed 2 sensor within the specified time. |
| Remedy: | 1) Open the side cover. Remove the jammed paper. 2) If jammed paper occurs continually, check the following. a) Enter SVC mode. Execute feed motor test. If the motor operation is normal, go to step d). b) Remove the rear cover. Check if the feed motor cable is connected correctly. c) If the connection is OK, replace the feed drive unit(JC93-00444A). d) If the feed motor operation is normal, check the feed 2 sensor. e) If the sensor operation is abnormal, check the harness. f) If the connection is OK, replace the feed sensor 2 (0604-001381). |
| Error code: | M2-1211, M2-1213, M2-1214 |
| Display: | Paper jam inside of machine. |
| Description: | Paper jam inside of machine. |
| Causes: | Paper jam has occurred inside the machine. (Regi. roller drive is defective / Regi. sensor is defective.) • M2–1211 : When the machine is warming-up, jammed paper inside machine is detected. • M2–1213 : The leading edge of the paper has not reached the regi. sensor within the specified time. • M2-1214 : The paper has not left from the regi. sensor within the specified time. |
| Remedy: | 1) Open the side cover. Remove the jammed paper. 2) If jammed paper occurs continually, check the following. a) Enter SVC mode. Execute Regi. motor test. If the motor operation is normal, go to step d). b) Remove the rear cover. Check if the Regi/MP motor cable is connected correctly. c) If the connection is OK, replace the Regi./MP drive unit(JC93-00443A). d) If the motor operation is normal, check the regi. sensor. e) If the sensor operation is abnormal, check the harness. f) If the connection is OK, replace the regi. sensor (0604-001381). |
| Error code: | M2-1331, M2-1333, M2-1334 |
| Description: | Paper jam inside of machine Paper jam at the top of duplex path |
| Causes: | Paper jam has occurred inside the machine. |
| Remedy: | 1) Open the side cover. Remove jammed paper. 2) If the problem persists, check the following: a) Check the Regi sensor harness. If the harness is normal, replace the Regi. sensor (0604-001381). b) Check the sensors in the Side Unit. If the harness is normal, replace the defective sensor (0604-001393 ). |
| Error code: | M2-2111, M2-2113, M2-2114 |
| Description: | Paper jam inside of machine Paper jam at the top of duplex path |
| Causes: | Paper jam has occurred inside the machine. |
| Remedy: | 1) Open the side cover. Remove jammed paper. 2) If the problem persists, check the following: a) Check the Regi sensor harness. If the harness is normal, replace the Regi. sensor (0604-001381). b) Check the sensors in the Side Unit. If the harness is normal, replace the defective sensor (0604-001393 ). |
| Error code: | M3-1411, M3-1413, M3-1414 |
| Description: | Paper jam in exit area. Check whether the pieces of paper remain in the paper path |
| Causes: | Paper jam has occurred around the fuser unit.(Job separator connection is defective. / Actuator-Exit is defective.) |
| Remedy: | 1) Open the side cover. Remove the jammed paper. 2) If the problem persists, check the following: a) Open the side cover. Check if the connector is connected properly. b) Remove the JOB-SEPARATOR. Check if the photo sensor is assembled correctly. c) Check if ACTUATOR-EXIT is assembled correctly. If the ACTUATOR-EXIT (JC66-02533A) is deformed or broken, replace it. d) If the photo sensor(0604-001393) is defective, replace it. |
| Error code: | M3-2230, M3-2430 |
| Display: | Output tray is full. Remove printed media. |
| Description: | Output tray is full. Remove printed media. |
| Causes: | There is too much paper in output bin tray or inner tray. • M3-2230 : There is too much paper in output bin tray. • M3-2430 : There is too much paper in inner tray. |
| Remedy: | 1) Remove the paper from output bin tray or inner tray. 2) If this error ccurs continually, check the following. a) Check if the bin-full sensor and actuator is assembled correctly. b) Check if the bin-full sensor(0604–001393) is defective. |
| Error code: | S1-1113 |
| Display: | Video System Failure #S1-1113: Turn off then on. |
| Description: | Video System Failure #S1-1113: Turn off then on. |
| Causes: | The system has some problems due to CPU overheating. |
| Remedy: | 1) Turn the machine off. 2) Wait until the machine is cool, and then turn the machine on. 3) If the problem persists, turn the machine off again. 4) Remove the rear cover. 5) Replace the main board(JC92-02742A). 6) Assemble the rear cover. Turn the machine on. |
| Error code: | S1-1114 |
| Display: | Video System Failure #S1-1114: Turn off then on. |
| Description: | Video System Failure #S1-1114: Turn off then on. |
| Causes: | CPU fan is not working |
| Remedy: | 1) Turn the machine off. 2) Wait until the machine is cool. And then turn the machine on. 3) If the problem persists, turn the machine off again. 4) Remove the rear cover. 5) Replace the main board(JC92-02746A). NOTE Insert the MSOK to the new main board. 6) Assemble the rear cover. Turn the machine on. |
| Error code: | S1-1313 |
| Display: | The clock became initial time. Set a time again. |
| Description: | The clock became initial time. Set a time again. |
| Causes: | Saved time is invalid |
| Remedy: | 1) Set up the time and reboot the machine. a) Select “Machine Setup” on touch screen. b) Select “General Setting”. c) Select “Date and Time” and set the time. 2) If the problem persists, check the following. a) Remove the rear cover. b) Remove the fax holder from the main board. c) Measure the voltage of the battery. If the battery is normal, the measured value is over 3V. 3) If the battery is normal, replace the main board(JC92-02742A). |
| Error code: | S1-2111 |
| Display: | Video System Failure #S1-2111: Turn off then on. |
| Description: | Video System Failure #S1-2111: Turn off then on. |
| Causes: | The machine can’t detect memory during booting. |
| Remedy: | 1) Turn the machine off then on. 2) If the problem persists, turn the machine off again. 3) Remove the rear cover. 4) Replace the main board(JC92-02742A). NOTE Insert the MSOK to the new main board. 5) Assemble the rear cover. Turn the machine on. |
| Error code: | S1-2411, S1-2421, S1-2422 |
| Display: | HDD System Failure #: Turn off then on. |
| Description: | HDD System Failure #S1-2411: Turn off then on. HDD System Failure #S1-2421: Turn off then on. HDD System Failure #S1-2422: Turn off then on. |
| Causes: | Hard Disk is not installed in the machine. / Hard Disk is defective. |
| Remedy: | 1) Check if the HDD is installed correctly. a) Remove the rear cover. b) Check if the HDD cable is connected correctly. 2) If the problem persists, replace the HDD(JC59–00035A). |
| Error code: | S1-2510, S1-2511, S1-2520 |
| Description: | Error message MSOK System Failure #S1-2510: Turn off then on. MSOK System Failure #S1-2511: Turn off then on. MSOK Failure: #S1-2520. Call for service. |
| Causes: | MSOK is not installed properly. / MSOK is defective. |
| Remedy: | 1) Remove the rear cover. 2) Check if the MSOK is inserted correctly. Remove and reinstall it. 3) If the problem persists, replace the main board(JC92-02742A). |
| Error code: | S1-2521 S1-2523 S1-2540 |
| Description: | MSOK Failure: #S1-2521. Call for service PPM data is incorrect. Call for service & change MSOK MSOK Failure: #S1-2540. Call for service & change MSOK |
| Causes: | MSOK is not installed properly. / MSOK is defective. |
| Remedy: | 1) Remove the rear cover. 2) Check if the MSOK is inserted correctly. Remove and reinstall it. 3) If the problem persists, replace the main board(JC92-02746A). |
| Error code: | S1-4111 |
| Display: | Video System Failure #S1-4111: Turn off then on. |
| Description: | Video System Failure #S1-4111: Turn off then on. |
| Causes: | The main board can’t send the data through the network channel. |
| Remedy: | 1) Check if the green LED of the network port is on. 2) If not, unplug and reconnect the network cable. 3) If the problem persists, replace the main board(JC92-02742A). |
| Error code: | S1-4311 |
| Display: | Video System Failure #S1-4311: Turn off then on. |
| Description: | Video System Failure #S1-4311: Turn off then on. |
| Causes: | The USB device chip is defective. |
| Remedy: | 1) Turn the machine off then on. 2) If the problem persists, turn the machine off again. 3) Replace the OPE hub board. 4) Turn the machine on. |
| Error code: | S1-5221 |
| Display: | Wireless Network Error |
| Description: | The communication error between the main board and the wireless board has occurred. |
| Causes: | Communication Error with wireless NIC has occurred. |
| Remedy: | Check if the connection between the main board and the wireless board is normal. If the connection is OK, replace the part in this order. (Flat cable -> Wireless board -> Main board) |
| Error code: | S2-1211, S2-2311 |
| Description: | Engine System Failure: #S2-1211. Turn off then on Engine System Failure: #S2-2311. Turn off then on |
| Causes: | The main board is defective. |
| Remedy: | 1) Turn the machine off then on. 2) If the problem persists, turn the machine off again. 3) Replace the main board(JC92-02746A). 4) Turn the machine on. |
| Error code: | S2-3321 |
| Display: | S2-3321, Supplying Toner / Supplying and mixing toner to developer unit. Please wait… |
| Description: | Supplying and mixing toner to developer unit. Please wait... |
| Causes: | Toner supply is insufficient. |
| Remedy: | 1) Machine will execute the toner supply job. Please wait until error message will be disappeared. 2) If the problem persists, check the toner supply drive unit. 3) If the problem persists, replace the toner cartridge. |
| Error code: | S2-3421 |
| Display: | S2-3421, Calibrating density / Calibrating image density. Please wait… |
| Description: | Calibrating image density. Please wait... |
| Causes: | Machine is on TC calibration. |
| Remedy: | 1) Machine will execute the toner calibration job. Please wait until error message will be disappeared. |
| Error code: | S2-4210 |
| Display: | Front door is open. Close it. |
| Description: | Front door is open. Close it. |
| Causes: | Front cover or Side cover is opened. |
| Remedy: | 1) Close the front cover correctly. 2) Check if the cover open sensor connector is connected properly. Reconnect it. 3) If the sensor is defective, replace it. |
| Error code: | S2-4410 |
| Display: | Right door is open. Close it. |
| Description: | Right door is open. Close it. |
| Causes: | Front cover or Side cover is opened. |
| Remedy: | 1) Close the side cover correctly. 2) Check if the cover open sensor connector is connected properly. Reconnect it. 3) If the sensor is defective, replace it. |
| Error code: | S3-3121 |
| Display: | Scanner Locked |
| Description: | CIS unit in the scanner does not move. |
| Causes: | Scanner lock error has occurred. CIS does not move. |
| Remedy: | 1) Check if the CIS unit moves when turning the machine off then on. 2) Check if the CIS cable is connected correctly. Reconnect it. 3) If the CIS unit is defective, replace it. 4) Check if there is any defective part in the scanner. Find and replace it. 5) If the problem persists, replace the main board. |
| Error code: | S3-3211, S3-3213, S3-3214 |
| Description: | Scan System Failure #S3-321x: Turn off then on. |
| Causes: | DSDF is not connected or communication error occurs with CIP6 board. |
| Remedy: | 1) Turn the machine off then on. If the problem persists, check the following: 2) Turn the machine off again. 3) Remove the scan rear cover. Check if the connector on scan joint board is connected correctly. 4) Remove the DSDF rear cover. Check if the connector on DSDF board is connected correctly. 5) If the connection is OK, replace the DSDF board(JC92-02446A). |
| Error code: | S3-3215, S3-3216, S3-3217 |
| Description: | Scan System Failure #S3-321x: Turn off then on. |
| Causes: | DSDF is not connected or communication error occurs with CIP6 board. |
| Remedy: | 1) Turn the machine off then on. If the problem persists, check the following: 2) Turn the machine off again. 3) Remove the scan rear cover. Check if the connector on scan joint board is connected correctly. 4) Remove the DSDF rear cover. Check if the connector on DSDF board is connected correctly. 5) If the connection is OK, replace the DSDF board(JC92-02446A). |
| Error code: | S4-3111 |
| Display: | Fax System Failure: #S4-3111. Install fax modem card again. |
| Description: | Fax System Failure: #S4-3111. Install fax modem card again. |
| Causes: | The fax board is not installed or defective. |
| Remedy: | 1) Check if the fax board is installed properly. 2) If the fax board is defective, replace it. 3) If the problem persists, replace the main board. |
| Error code: | S5-3111 |
| Display: | UI System Failure #S5-3111:Turn off then on. |
| Description: | UI System Failure #S5-3111:Turn off then on. |
| Causes: | Main board has critical problem which make its lockup or USB connection between main board and OPE has some problem. |
| Remedy: | 1) Turn off and turn on. And check if the problem disappears. a) If yes, go to step 2)-a). b) If no, go to step 2)-b). 2) Check the following procedure. a) Print the Error Information Report. . Service Mode - General - Print Reports - Error Information . Check the error code which is printed on the report. - If S5-3111 has occurred, go to step 4). - If S5-3112 has occurred, go to step 5)-c). - If S5-3113 has occurred, go to step 5)-d). b) Enter into System Recovery Mode. . How to enter System Recovery Mode : Turn on the machine with side cover open and power button on OPE is pressed state. . Check if entering System Recovery Mode is possible or not. - If entering System Recovery Mode is successful, go to step 3). - If entering System Recovery Mode fails, go to step 5)-d). 3) Execute the System Recovery. • Insert USB memory stick which has recovery one rom and execute recovery(HDD format). • Check if the problem disappears after system recovery(format complete). - If yes, go to step 4). - If no, go to step 5)-c). 4) Execute the firmware update. • Check if the problem disappears after one rom update. - If the problem disappears, go to step 5)-a). - If the problem happens sometimes, go to step 5)-b). 5) Check the following procedure. a) No more action is required because machine is recovered from S5-3111 error state. Please monitor the machine if S5-3111 happens again. b) Detailed analysis is required. Please capture the log and send it to development team in HQ. c) It seems that HDD or main board has some problem. Please replace HDD or main board with new one and check if the problem disappears. d) It seems that there is some critical issue in the USB connection between main board and OPE. Please try below steps. i) If WiFi module is installed, replace WiFi module with new one. ii) Check USB cable state between main board and OPE. iii) Replace the main board with new one. iv) Replace the OPE board with new one. |
| Error code: | S6-3122 |
| Display: | Network cable is disconnected. Check it. |
| Description: | Network cable is disconnected. Check it. |
| Causes: | Network cable is disconnected. |
| Remedy: | 1) Check if the green LED of the network port is on. 2) If not, unplug and reconnect the network cable. 3) If the problem persists, replace the main board(JC92-02742A). |
| Error code: | S6-3123, S6-3128 |
| Display: | This IP address conflicts with that of other system. Check it. 802.1x authentication failed. Please Contact the System Administrator. |
| Description: | Network Problem: IP Conflict 802.1x Network Error |
| Causes: | IP address conflicts with that of other system. |
| Remedy: | 1) Change the machine’s IP address. 2) Check the setting-up for 802.1x confirmation server. |
| Error code: | S7-1110 |
| Display: | Failure: #S7-1110. Turn off then on |
| Description: | Engine System Failure: #S7-1110. Turn off then on |
| Causes: | 24V power is abnormal. |
| Remedy: | 1) Check the 24V pin on SMPS board. If it is abnormal, replace the SMPS board. 2) Check the related cable. 3) If the SMPS is normal, replace the main board. |
| Error code: | S7-2110 |
| Display: | Fuser Failure: #S7-2110. Turn off then on |
| Description: | Fuser Failure: #S7-2110. Turn off then on |
| Causes: | Heater control relay is abnormal. |
| Remedy: | 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) If the problem persists, replace the Fuser unit(110V : JC91-01158A, 220V : JC91-01157A). |
| Error code: | U1-2113, U1-2119 |
| Display: | Fuser Unit Failure: #U1-2113. Fuser Unit Failure: #U1-2119. |
| Description: | Fuser Unit Failure: #U1-2113. Fuser Unit Failure: #U1-2119. |
| Causes: | The thermistor can’t measure temperature. The hear-roller will not heat-up. |
| Remedy: | • U1–2113 : Error occurs at non-contact type Thermistor • U1–2119 : Error occurs at contact type Thermistor 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) Remove the fuser unit. After opening the jam cover, check if jammed or wrapped paper is in the fuser unit. 3) If the problem persists, check the following: a) Check if the Halogen lamp (110V : 4713–001632 / 220V : 4713–001633) is broken or disconnected. b) Check if the AC connection of the Halogen lamp is disconnected or contaminated. c) Check if the thermistat(4712-001098) is disconnected. d) Check if the contact type thermistor(1404–001567) or Non-contact type thermistor(1404–001453)is broken. 4) If the problem persists, replace the Fuser unit(220V : JC91–01163A / 110V : JC91–01164A). 5) If the problem persists, replace the main board(JC92–02746A) or FDB board(220V : JC44-00211A, 110V : JC44-0021A)or SMPS(220V : JC44-00100C, 110V : JC44-00093C) |
| Error code: | U1-2115 |
| Display: | Fuser Unit Failure: #U1-2115. Turn off then on. |
| Description: | Fuser Unit Failure: #U1-2115. Turn off then on. |
| Causes: | The pressure control unit(Cam unit)of the fuser is abnormal. |
| Remedy: | 1) Turn the machine off then open the side cover. 2) Remove and re-install the fuser unit, then turn the machine on. 3) If the problem persists, check the following : a) When the side-cover closes, check if the operation sound of the pressure control unit occurs. b) Check if the parts of the pressure control unit are abnormal. - Check if the shape of the CAM-REAR(JC66-03299A)) is broken. - Check if there are abnormal parts of the pressure control unit. c) Check if the fuser-motor is abnormal via SVC mode. 4) If the problem persists, replace the Fuser unit(110V : JC91-01158A, 220V : JC91-01157A). 5) If the problem persists, replace the pressure control unit or cam-motor or Main board(JC92-02742A). |
| Error code: | U1-2132, U1-2135 |
| Display: | Fuser Unit Failure: #U1-2132. Fuser Unit Failure: #U1-2135. |
| Description: | Fuser Unit Failure: #U1-2132. Fuser Unit Failure: #U1-2135. |
| Causes: | Temperature of the fuser rises abnormally. |
| Remedy: | • U1–2132 : Error occurs at non-contact type Thermistor • U1–2135 : Error occurs at contact type Thermistor 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?) 3) Remove the fuser unit. After opening the jam cover, check jammed or wrapped paper is in the fuser unit. 4) If the problem persists, Check the following: a) Check if the Halogen lamp (110V : 4713–001632 / 220V : 4713–001633) is broken or disconnected. b) Check if the AC connection of the Halogen lamp is disconnected or contaminated. c) Check if the thermistat(4712-001098) is disconnected. d) Check if the contact type thermistor(1404–001567) or Non-contact type thermistor(1404–001453) is broken. 5) If the problem persists, replace the Fuser unit(220V : JC91–01163A / 110V : JC91–01164A). 6) If the problem persists, replace the main board(JC92–02746A) or FDB board(220V : JC44-00211A, 110V : JC44-0021A)or SMPS(220V : JC44-00100C, 110V : JC44-00093C) |
| Error code: | U1-2141, U1-2142 |
| Display: | Fuser Unit Failure: #U1-2141. Fuser Unit Failure: #U1-2142. |
| Description: | Fuser Unit Failure: #U1-2141. Fuser Unit Failure: #U1-2142 |
| Causes: | Temperature of the thermistor is higher than the maximum allowable temperature. |
| Remedy: | • U1–2141 : Error occurs at non-contact type Thermistor • U1–2142 : Error occurs at contact type Thermistor 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?) 3) Remove the fuser unit. After opening the jam cover, check if jammed or wrapped paper is in the fuser unit. 4) If the problem persists, Check the following: a) Check if the contact type thermistor(1404–001567) or Non-contact type thermistor(1404–001453) is broken. 5) If the problem persists, replace the Fuser unit(220V : JC91–01163A / 110V : JC91–01164A). 6) If the problem persists, replace the main board(JC92–02746A) or FDB board(220V : JC44-00211A, 110V : JC44-0021A)or SMPS(220V : JC44-00100C, 110V : JC44-00093C) |
| Error code: | U1-2316, U1-2317 |
| Display: | Fuser Unit Failure: #U1-2316. Fuser Unit Failure: #U1-2317. |
| Description: | Fuser Unit Failure: #U1-2316. Fuser Unit Failure: #U1-2317 |
| Causes: | Temperature of the fuser changes abnormally |
| Remedy: | • U1–2316 : Error occurs at non-contact type Thermistor • U1–2317 : Error occurs at contact type Thermistor 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?) 3) If the problem persists, Check the following: a) Check if the Halogen lamp (110V : 4713–001632 / 220V : 4713–001633) is broken or disconnected. b) Check if the AC connection of the Halogen lamp is disconnected or contaminated. c) Check if the thermistat(4712-001098) is disconnected. d) Check if the contact type thermistor(1404–001567) or Non-contact type thermistor(1404–001453) is broken. 4) If the problem persists, replace the Fuser unit(220V : JC91–01163A / 110V : JC91–01164A). 5) If the problem persists, replace the main board(JC92–02746A) or FDB board(220V : JC44-00211A, 110V : JC44-0021A)or SMPS(220V : JC44-00100C, 110V : JC44-00093C) |
| Error code: | U1-2335, U1-233A |
| Display: | Fuser Unit Failure: #U1-2335. Fuser Unit Failure: #U1-233A. |
| Description: | Fuser Unit Failure: #U1-2335. Fuser Unit Failure: #U1-233A. |
| Causes: | Temperature of the thermistor is abnormally low. |
| Remedy: | • U1–2335 : Error occurs at non-contact type Thermistor • U1–233A : Error occurs at contact type Thermistor 1) Turn the machine off. Re-install the fuser uni, then turn the machine on. 2) Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?) 3) Remove the fuser unit. After opening the jam cover, check if jammed or wrapped paper is in the fuser unit. 4) If the problem persists, Check the follows. a) Check if the Halogen lamp (110V : 4713–001632 / 220V : 4713–001633) is broken or disconnected. b) Check if the AC connection of the Halogen lamp is disconnected or contaminated. c) Check if the thermistat(4712-001098) is disconnected. d) Check if the contact type thermistor(1404–001567)or Non-contact type thermistor(1404–001453) is broken. 5) If the problem persists, replace the Fuser unit(220V : JC91–01163A / 110V : JC91–01164A). 6) If the problem persists, replace the main board(JC92–02746A) or FDB board(220V : JC44-00211A, 110V : JC44-0021A)or SMPS(220V : JC44-00100C, 110V : JC44-00093C) |
| Error code: | U1-2337, U1-233D |
| Display: | Fuser Unit Failure: #U1-2337. Fuser Unit Failure: #U1-233D |
| Description: | Fuser Unit Failure: #U1-2337. Fuser Unit Failure: #U1-233D. |
| Causes: | When the fuser warms-up, the temperature of the thermistor is abnormally low. |
| Remedy: | • U1–2337 : Error occurs at non-contact type Thermistor • U1–233D : Error occurs at contact type Thermistor 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) Check if the power voltage is normal. (Is the voltage during the operation ±10% of the rated voltage?) 3) Remove the fuser unit. After opening the jam cover, check if jammed or wrapped paper is in the fuser unit. 4) If the problem persists, Check the follows. a) Check if the Halogen lamp (110V : 4713–001632 / 220V : 4713–001633) is broken or disconnected. b) Check if the AC connection of the Halogen lamp is disconnected or contaminated. c) Check if the thermistat(4712-001098) is disconnected. d) Check if the contact type thermistor(1404–001567)or Non-contact type thermistor(1404–001453) is broken. 5) If the problem persists, replace the Fuser unit(220V : JC91–01163A / 110V : JC91–01164A). 6) If the problem persists, replace the main board(JC92–02746A) or FDB board(220V : JC44-00211A, 110V : JC44-0021A)or SMPS(220V : JC44-00100C, 110V : JC44-00093C) |
| Error code: | U2-1111, U2-1112 |
| Display: | U2-1111, U2-1112, U2-1113, U2-1114 LSU failure errors |
| Description: | LSU Failure: #U2-1111. Turn off then on. LSU Failure: #U2-1112. Turn off then on. |
| Causes: | LSU motor does not operate of it operates abnormally. Motor ready signal is abnormal. |
| Remedy: | 1) Turn the machine off then on. Check for the LSU motor operation sound during warm-up. 2) Print a Demo page and check the printout is normal. 3) If the problem persists, check the following: • If the LSU motor makes a sound, a) By SVC mode, Check if the motor ready signal is occurred. (Diagnostics > Engine Diagnostics > Engine Test Routines > 110–0000) b) If not, open the side-cover and replace the LSU(JC97–04017B) • If the LSU motor does not make a sound, a) Unplug and reconnect the LSU flat cable connecting the LSU. Then check the operation sound of LSU. b) Unplug and reconnect the LSU flat cable on main board. Then check the operation sound of LSU. c) If the LSU flat cable is defective, replace FFC. d) If the LSU cable is OK, replace the LSU(JC97–04017B) |
| Error code: | U2-1113, U2-1114 |
| Display: | U2-1111, U2-1112, U2-1113, U2-1114 LSU failure errors |
| Description: | LSU Failure: #U2-1113. Turn off then on. LSU Failure: #U2-1114. Turn off then on. |
| Causes: | LSU motor does not operate of it operates abnormally. Motor ready signal is abnormal. |
| Remedy: | 1) Turn the machine off then on. Check for the LSU motor operation sound during warm-up. 2) Print a Demo page and check the printout is normal. 3) If the problem persists, check the following: • If the LSU motor makes a sound, a) By SVC mode, Check if the motor ready signal is occurred. (Diagnostics > Engine Diagnostics > Engine Test Routines > 110–0000) b) If not, open the side-cover and replace the LSU(JC97–04017B) • If the LSU motor does not make a sound, a) Unplug and reconnect the LSU flat cable connecting the LSU. Then check the operation sound of LSU. b) Unplug and reconnect the LSU flat cable on main board. Then check the operation sound of LSU. c) If the LSU flat cable is defective, replace FFC. d) If the LSU cable is OK, replace the LSU(JC97–04017B) |
| Error code: | U3-3122 |
| Description: | Documents are inserted incorrectly. After open the scanner`s door, put it again. Call for service if the problem persists |
| Causes: | DSDF pick up module has the problem. |
| Remedy: | 1) Open and close the DSDF cover. Check if the error message is disappeared. 2) Open the DSDF cover. Push and release the pick up module. Check if the pick up module returns the original position. • Check if the spring is deformed. If the spring is defective, replace it(6107–003581). 3) Check If the regi sensor is OK, check the scan sensor and scan actuator. If their operation is abnormal, replace the defective part. |
| Error code: | U3-3211, U3-3213, U3-3214 |
| Display: | U3-3211, U3-3213, U3-3214, U3-3311, U3-3313, U3-3314 Original paper jam / Original paper jam inside of scanner. Remove jam |
| Description: | Original paper jam inside of scanner |
| Causes: | Jam has occurred inside the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the Regi. sensor and Regi actuator. Push and release the regi actuator. Check if the pick up module returns the original position. If the sensor is defective, replace it(0604–001393). 3) If the regi sensor is OK, check the scan 1 sensor and reflect film. • If the scan 1 sensor is defective, replace it(0604–001381). • If the reflect film is contaminated, clean it. |
| Error code: | U3-3311, U3-3313, U3-3314 |
| Display: | U3-3211, U3-3213, U3-3214, U3-3311, U3-3313, U3-3314 Original paper jam / Original paper jam inside of scanner. Remove jam |
| Description: | Original paper jam inside of scanner |
| Causes: | Jam has occurred inside the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the Regi. sensor and Regi actuator. Push and release the regi actuator. Check if the pick up module returns the original position. If the sensor is defective, replace it(0604–001393). 3) If the regi sensor is OK, check the scan 1 sensor and reflect film. • If the scan 1 sensor is defective, replace it(0604–001381). • If the reflect film is contaminated, clean it. |
| Error code: | U3-3413, U3-3414, U3-3511 |
| Description: | Original paper jam inside of scanner. |
| Causes: | Jam has occurred inside the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the Regi. sensor and Regi actuator. Push and release the regi actuator. Check if the pick up module returns the original position. If the sensor is defective, replace it(0604–001393). 3) If the regi sensor is OK, check the scan 2 sensor and exit sensor. • If the scan 2 sensor is defective, replace it(0604–001381). • If the exit sensor is defective, replace it(6107–003581). |
| Error code: | U3-3513, U3-3514 |
| Display: | Original paper jam inside the scanner |
| Description: | Original paper jam inside of scanner. |
| Causes: | Jam has occurred inside the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the Regi. sensor and Regi actuator. Push and release the regi actuator. Check if the pick up module returns the original position. If the sensor is defective, replace it(0604–001393). 3) If the regi sensor is OK, check the scan 2 sensor and exit sensor. • If the scan 2 sensor is defective, replace it(0604–001381). • If the exit sensor is defective, replace it(6107–003581). |
| Error code: | U3-3611, U3-3613 |
| Description: | Original paper jam in the exit area of scanner |
| Causes: | Jam has occurred in exit area of the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If the regi sensor is OK, check the scan 2 sensor and exit sensor. • If the scan 2 sensor is defective, replace it(0604–001381). • If the exit sensor is defective, replace it(6107–003581). |
| Error code: | U3-3614, U3-3713 |
| Description: | Original paper jam in the exit area of scanner |
| Causes: | Jam has occurred in exit area of the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If the regi sensor is OK, check the scan 2 sensor and exit sensor. • If the scan 2 sensor is defective, replace it(0604–001381). • If the exit sensor is defective, replace it(6107–003581). |
| Error code: | U3-4210 |
| Display: | Top door of scanner is open. |
| Description: | Top door of scanner is open. |
| Causes: | DSDF cover is open. |
| Remedy: | 1) Open and close the DSDF cover. Check if the error message is disappeared. 2) If the problem persists, check the cover open sensor. a) Open the DSDF cover. Remove the spring. b) Remove 4 screws. c) Check if the sensor connector is connected correctly. If the sensor is defective, replace it(0604–001393). |
