Samsung MultiXpress M4370LX
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A4
Число страниц в месяц
250000
Скорость печати
A4
43
Цветность печати
черно-белая
Общие характеристики |
|
|---|---|
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Цветность печати |
|
Область применения |
большой офис |
Число страниц в месяц |
250 000 |
Размещение |
настольный |
Макс. формат |
A4 |
Факс |
|
Телефон |
|
Печать фотографий |
|
Сканер |
|
Копир |
|
Тип устройства |
МФУ |
Принтер |
|
Прямая печать |
|
Двусторонняя печать |
|
Пигментные чернила |
|
Печать без полей |
|
Макс, разрешение для ч/б печати |
|
| По X | 1 200 |
| По Y | 1 200 |
Скорость ч/б печати |
|
| A4 | 43 |
Время выхода первого отпечатка |
|
| Ч/б | 8 |
Копир |
|
Макс, количество копий за цикл |
9 999 |
Время выхода первой копии |
5 |
Значение масштаба |
|
| Минимальное | 0,25 |
| Максимальное | 4 |
Макс, разрешение (ч/б) |
|
| По X | 1 200 |
| По Y | 600 |
| По Y | 1 200 |
Сканер |
|
Тип сканера |
планшетный/протяжный |
Устройство автоподачи оригиналов |
двустороннее |
Стандарт WIA |
|
Слайд-адаптер |
|
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Емкость устройства автоподачи оригиналов |
100 |
Макс. формат оригинала |
A4 |
Разрешение сканера |
|
| По Y (улучшенное) | 4 800 |
| По Х (улучшенное) | 4 800 |
| По Х | 600 |
Расходные материалы |
|
Количество картриджей |
1 |
Ресурс фотобарабана |
100 000 |
Ресурс ч/б картриджа/тонера |
30 000 |
Печать на: |
|
| Карточках |
|
| Матовой бумаге |
|
| Конвертах |
|
| Глянцевой бумаге |
|
| Этикетках |
|
| Фотобумаге |
|
| CD/DVD |
|
| Рулоне |
|
| Пленках |
|
Плотность бумаги |
|
| Максимальная | 163 |
| Минимальная | 60 |
Факс |
|
PC Fax |
|
Цветной |
|
Телефон |
|
Проводная трубка |
|
Беспроводная трубка |
|
Стандарт DECT |
|
Спикерфон |
|
Автоответчик |
|
Caller ID |
|
АОН |
|
Языки управления |
|
| PostScript |
|
| PostScript 3 |
|
|
|
|
| PCL 5c |
|
| PCL 6 |
|
| PostScript 2 |
|
| PCL 5e |
|
| PPDS |
|
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
| Максимальная | 3 240 |
| Стандартная | 620 |
Финишер |
|
Степлер |
|
Сортер |
|
Электронная сортировка |
|
Сортировка со сдвигом |
|
Брошюровщик |
|
Интерфейсы |
|
Версия USB |
2,0 |
Ethernet (RJ-45) |
|
USB |
|
AirPrint |
|
Веб-интерфейс |
|
LPT |
|
Устройство для чтения карт памяти |
|
FireWire (IEEE 1394) |
|
Bluetooth |
|
Wi-Fi 802.11n |
|
Wi-Fi |
|
RS-232 |
|
Инфракрасный порт |
|
Память/Процессор |
|
Емкость жесткого диска |
320 |
Макс, объем памяти |
2 048 |
Объем памяти |
2 048 |
Дополнительная информация |
|
Диагональ дисплея |
10,1 |
Экран |
|
Работа от аккумулятора |
|
Поддержка ОС |
|
| Linux |
|
| Windows |
|
| Mac OS |
|
| DOS |
|
Потребляемая мощность |
|
| В режиме ожидания | 1,5 |
| При работе | 800 |
Уровень шума |
|
| При работе | 58 |
| В режиме ожидания | 37 |
Габариты |
|
Глубина |
506 |
Высота |
636 |
Вес |
49 |
Ширина |
630 |
Модули
DUPLEX SUB-SIDE
FRAME-HOUSING MAIN
DSDF-OPEN
COVER
Frame-Base
FRAME-HOUSING MP
DRIVE-MAIN
DRIVE-FUSER
Fuser
FRAME
PLATEN
CASSETTE
FRAME-HOUSING BASE
DSDF
MAIN
Exit
COVER-HOUSING SIDE
DSDF-PLATEN
ELA HOU-DUPLEX
DSDF-FRAME MAIN
FRAME-HOUSING PLATE UPPER
Детали DSDF-OPEN
| Деталь: | CAP-M_SIDE, SCX-6345N/XRX,ABS,T2,354.9mm, |
| Парткод: | JC67-00112A |
| Деталь: | MP SUB-SIDE, M5370,SEC |
| Парткод: | JC90-01269A |
| Деталь: | COVER-HOUSING SIDE, M5370,SEC |
| Парткод: | JC95-01922A |
| Деталь: | ELA HOU-DUPLEX, SCX-6555N,SEC,-,-,- |
| Парткод: | JC96-04982A |
| Деталь: | MEA UNIT-TR, SCX-6345N/XRX,XEROX,-,TR,-,- |
| Парткод: | JC97-02287A |
| Деталь: | TRAY-ASF IN MP, M5370,HIPS,235,SPILIT GRA |
| Парткод: | JC63-00447H |
| Деталь: | TRAY-ASF IN TOP, M5370,ABS,1.5,SPILIT GRA |
| Парткод: | JC63-00745C |
| Деталь: | ADJUST-SIDE GUIDE MP R, M5370,HIPS,SHG85, |
| Парткод: | JC72-01006D |
| Деталь: | GEAR-PINION, SF4000,POM,1,Z16,WHT |
| Парткод: | JG66-40003A |
| Цена: | 260 ₽ |
| Деталь: | COVER-TRAY LOWER, M5370,HIPS,SPLIT GRAY,H |
| Парткод: | JC63-04487A |
| Деталь: | ADJUST-SIDE GUIDE MP L, M5370,HIPS,SHG85, |
| Парткод: | JC72-01005E |
| Деталь: | MEA UNIT-TR SUB, SCX-6345N/XRX,XEROX,-,-, |
| Парткод: | JC97-02375A |
| Деталь: | BAND, SCX-5312F,PC+ABS,EMBER GOLD |
| Парткод: | JC72-00883A |
| Деталь: | BAND, SCX-5312F,PC+ABS,EMBER GOLD |
| Парткод: | JC72-00884A |
| Деталь: | SPRING ETC-TR_R, ML-165,SUS304WPB,PI0.5,O |
| Парткод: | JC61-70906A |
| Деталь: | ROLLER-TRANSFER, Rushmore,18.4 (mm),EPDM |
| Парткод: | JC66-01023A |
| Деталь: | FAN, SCX-6555N,PBT+GF,HNS100mm,24,150mA |
| Парткод: | JC31-00099A |
| Деталь: | DUCT-M_FAN LSU, SCX-6345N/XRX,ABS ,T1.5,W |
| Парткод: | JC67-00127A |
| Деталь: | HOLDER-FUSER LAMP, SCX-6555N,PC,T2,BLK |
| Парткод: | JC61-02257A |
| Деталь: | FRAME-M_COVER REAR, SCX-6345N/XRX,ABS,HB, |
| Парткод: | JC61-01316A |
| Деталь: | MEA UNIT-DAMPER,L, SCX-6345N/XRX,XEROX,DA |
| Парткод: | JC97-02301A |
| Деталь: | ROLLER-IDLE REGI, SCX-6345N,SUM22,15 |
| Парткод: | JC66-01028A |
| Деталь: | ROLLER FEED-REGI, M5370,EPDM,SUM22,6 |
| Парткод: | JC66-04242A |
| Деталь: | FRAME-HOUSING CVR OPN, M5370,SEC |
| Парткод: | JC93-00888A |
| Деталь: | FRAME-HOUSING TERMINAL, M5370,SEC |
| Парткод: | JC93-00899A |
| Деталь: | PBA-TCRUM_IF, SCX-6555N,SEC,EXPORT,-,-,-, |
| Парткод: | JC92-01963A |
| Деталь: | HOLDER-TONER CRUM, SCX-6555N,PC+ABS,BLK,V |
| Парткод: | JC61-02422A |
| Деталь: | GROUND-P-P FUSER, SCX-6345N/XRX,STS301,0. |
| Парткод: | JC63-00797A |
| Деталь: | GROUND-P-MAIN DRIVE L, SCX-6345N/XRX,STS3 |
| Парткод: | JC63-00799A |
| Деталь: | GROUND-P-OPC CONTACT, SCX-6345N/XRX,PBS-C |
| Парткод: | JC63-00802A |
| Деталь: | GROUND-P-OPE REAR, SCX-6345N/XRX,PBS-C521 |
| Парткод: | JC63-00800A |
| Деталь: | MEA UNIT-REGI F, SCX-6345N/XRX,XEROX,-,RE |
| Парткод: | JC97-02262A |
| Деталь: | MEA UNIT-REGI R, SCX-6345N/XRX,XEROX,-,RE |
| Парткод: | JC97-02261A |
| Деталь: | COVER-OPEN UPPER, M5370,ABS,G32690,HF-066 |
| Парткод: | JC63-04428A |
| Деталь: | COVER-OPEN HANDLE, M5370,ABS+PC,G32690,23 |
| Парткод: | JC63-04437A |
| Деталь: | HOLDER-REGI SPRING L, CLX-8650ND,ABS,34.8 |
| Парткод: | JC61-05548A |
| Деталь: | PHOTO-INTERRUPTER, TR,DIP-4,BK |
| Парткод: | 0604-001415 |
| Цена: | 240 ₽ |
| Деталь: | ACTUATOR-REGI, CLX-8650ND,PC,18.9,60.8,BL |
| Парткод: | JC66-03531A |
| Деталь: | ROLLER-REGI IDLE, CLX-8650ND,POM,6,19 |
| Парткод: | JC66-03751A |
| Деталь: | ACTUATOR-PICKUP-FEED, CLX-8650ND,PC,24,51 |
| Парткод: | JC66-03529A |
| Деталь: | BRUSH-PICK UP ANTISTATIC, CLX-8650ND,SUS |
| Парткод: | JC67-00667A |
| Деталь: | ACTUATOR-DETECT, CLX-8650ND,PC,45,35.6,BL |
| Парткод: | JC66-03530A |
| Деталь: | ACTUATOR-DETECT B, CLX-8650ND,PC,31.1,35. |
| Парткод: | JC66-03532A |
| Деталь: | COVER-OPEN LOWER, M5370,ABS,G32690,HF-066 |
| Парткод: | JC63-04427A |
| Деталь: | HOLDER-REGI SPRING R, CLX-8650ND,ABS,2,34 |
| Парткод: | JC61-05547A |
| Деталь: | COVER-UNIT TOP, M5370,SEC |
| Парткод: | JC95-01915A |
| Деталь: | COVER-LEFT TOP, M5370,HIPS,Split Gray,HIP |
| Парткод: | JC63-04458A |
| Деталь: | COVER-EXIT BOTTOM, M5370,SEC |
| Парткод: | JC95-01914A |
| Деталь: | COVER-FRONT TOP, M5370,ABS,Split Brown Bl |
| Парткод: | JC63-04457A |
| Деталь: | COVER-FRONT, M5370,SEC |
| Парткод: | JC95-01897A |
| Деталь: | COVER-INNER FRONT, M5370,SEC |
| Парткод: | JC95-01917A |
| Деталь: | COVER-PORT, M5370,SEC |
| Парткод: | JC95-01918A |
| Деталь: | COVER-REAR, M5370,SEC |
| Парткод: | JC95-01916A |
| Деталь: | MEA UNIT-COVER UPPER, SCX-6345N/XRX,SEC,- |
| Парткод: | JC97-02274B |
| Деталь: | FRAME-HOUSING MAIN, M5370 |
| Парткод: | JC93-00877A |
| Деталь: | FRAME-SUPPORT SCAN, M5370,SEC |
| Парткод: | JC93-00879A |
| Деталь: | GROUND-P-FUSER DRV, SCX-6345N/XRX,STS301, |
| Парткод: | JC63-00790A |
| Деталь: | GROUND-P-MAIN DRV, SCX-6345N/XRX,STS301,0 |
| Парткод: | JC63-00789A |
| Деталь: | GEAR-M_RETARD, SCX-6345N/XRX,POM,0.6,57,H |
| Парткод: | JC66-00975A |
| Деталь: | GEAR-M_FORWARD, SCX-6345N/XRX,POM,1,31,H9 |
| Парткод: | JC66-00974A |
| Деталь: | GEAR-M_PICKUP IDLE B, SCX-6345N/XRX,POM,A |
| Парткод: | JC66-00973A |
| Деталь: | CAP-M_INLET, SCX-6345N/XRX,PC+ABS,T2.5,W8 |
| Парткод: | JC67-00113A |
| Деталь: | FAN-DC, CLX-8380ND/XAA,UL10272 AWG26, AM |
| Парткод: | JC31-00086A |
| Деталь: | FRAME-HOUSING BASE, M5370,SEC |
| Парткод: | JC93-00878A |
| Деталь: | MEA UNIT-ACT FEED, SCX-6345N,XEROX,-,-,- |
| Парткод: | JC97-02702A |
| Деталь: | MEA UNIT-ACT REGI, SCX-6345N,XEROX,GB,-,- |
| Парткод: | JC97-02703A |
| Деталь: | PLATE-M_FEED UPPER, SCX-6345N/XRX,ABS,T2, |
| Парткод: | JC61-01295A |
| Деталь: | LEG-M_ACT FEED BASE, SCX-6345N/XRX,POM,2, |
| Парткод: | JC61-01426A |
| Деталь: | SPRING-TS, STAINLESS-STS304,0.35,ID4.6,OD |
| Парткод: | 6107-001261 |
| Деталь: | HOLDER-M_ACT_FEED, SCX-6345N/XRX,PC,T2,W1 |
| Парткод: | JC61-01421A |
| Деталь: | LEG-M_ACTUATOR REGI, SCX-6345N/XRX,POM,2, |
| Парткод: | JC61-01408A |
| Деталь: | FRAME-M_MP TOP, M5370,ABS,SPLIT GRAY,HF-0 |
| Парткод: | JC61-01352C |
| Деталь: | SPONGE-DAMPER MP, SCX-6345N/XRX,POLYURETH |
| Парткод: | JC72-01375A |
| Деталь: | GEAR-M_MP FEED, SCX-6345N/XRX,POM,1,24,H2 |
| Парткод: | JC66-00936A |
| Деталь: | ROLLER-MP DRV, SCX-6345N,EPDM,SUM22,6 |
| Парткод: | JC66-01026A |
| Деталь: | STOPPER-M_PAPER FRT, SCX-6345N/XRX,POM,T2 |
| Парткод: | JC61-01307A |
| Деталь: | ELA HOU-MP PICK UP, SCX-6345N/XRX,-,-,MP |
| Парткод: | JC96-03533A |
| Деталь: | LATCH-M_ARM REAR, SCX-6345N/XRX,POM,T1.5, |
| Парткод: | JC66-00958B |
| Деталь: | PHOTO-INTERRUPTER, TR,DIP-4,BK |
| Парткод: | 0604-001415 |
| Цена: | 240 ₽ |
| Деталь: | FRAME-M MP LOWER, ABS,SPLIT GRAY,HF-0660I |
| Парткод: | JC61-01351C |
| Деталь: | MEC-ADF ROLLER ASSY, SCX-1110F/XRX,XEROX, |
| Парткод: | JB75-00299A |
| Цена: | 330 ₽ |
| Деталь: | MEC-PICK UP ROLLER ASSY, SCX-1110F/XRX,XE |
| Парткод: | JB75-00300A |
| Цена: | 220 ₽ |
| Деталь: | GEAR-ADF IDLE 34, SCX-1110F,POM,0.6,34,20 |
| Парткод: | JB66-00104A |
| Деталь: | GEAR-PICK UP IDEL 38, SCX-1110F,POM,0.6,3 |
| Парткод: | JB66-00102A |
| Деталь: | GEAR-PICK UP 26, SCX-1110F,POM,0.6,26,15. |
| Парткод: | JB66-00105A |
| Деталь: | DRIVE MAIN, SCX-6555N,SEC |
| Парткод: | JC93-00168A |
| Деталь: | MOTOR BLDC, 2220 RPM,1400gf.cm,DC24V,2.1A |
| Парткод: | JC31-00090A |
| Цена: | 2 900 ₽ |
| Деталь: | CABLE CLAMP, DAWS-3NE,ID11L34.8,NYLON66, |
| Парткод: | 6502-001093 |
| Деталь: | CABLE CLAMP, DAWS-1NE,ID11,L21.0,NTR,NYLO |
| Парткод: | 6502-000132 |
| Деталь: | MOTOR DC, NF213G-1020515,DC24V,CLX-8380ND |
| Парткод: | JC31-00078A |
| Цена: | 1 600 ₽ |
| Деталь: | GEAR-AGI IDLE B, SCX-6555N,POM,0.5/1,86/1 |
| Парткод: | JC66-01679A |
| Деталь: | CAP-GEAR, SCX-6555N,HIPS,T2.0,BLK |
| Парткод: | JC67-00276A |
| Деталь: | COUPLER, SCX-5100,DE8903,BLK |
| Парткод: | JC72-00743A |
| Деталь: | GEAR-M_AGI IDLE, SCX-6345N/XRX,POM,1,31/5 |
| Парткод: | JC66-00989A |
| Деталь: | GEAR-M_SUPPLY IDLE, SCX-6345N/XRX,POM,A:0 |
| Парткод: | JC66-00993A |
| Деталь: | GEAR-M_MIXER, SCX-6345N/XRX,POM,1,27,D34. |
| Парткод: | JC66-00985A |
| Деталь: | MEA UNIT-GEAR SUPPLY, SCX-6345N/XRX,XEROX |
| Парткод: | JC97-02681A |
| Деталь: | GEAR-M_OPC BASE, SCX-6345N/XRX,POM,0.5,79 |
| Парткод: | JC66-00982A |
| Деталь: | OTHER MECHA-M CPL OPC, SCX-6345,POM M90-4 |
| Парткод: | JC67-00115A |
| Деталь: | GEAR-MIDDLE, SCX-6555N,POM,1,21,NTR,HELIC |
| Парткод: | JC66-01678A |
| Деталь: | GEAR-REGI IDLE C, SCX-6555N,POM,1/1,19/31 |
| Парткод: | JC66-01677A |
| Деталь: | GEAR-PICK UP HELICAL, SCX-6555N,POM,1/1,3 |
| Парткод: | JC66-01682A |
| Деталь: | GEAR-MP HELICAL, SCX-6555N,PA66,1/1,17/18 |
| Парткод: | JC66-01680A |
| Деталь: | GEAR-M_MP IDLE B, SCX-6345N/XRX,POM,A:1,B |
| Парткод: | JC66-00990A |
| Деталь: | GEAR-M_DUPLEX IDLE, SCX-6345N/XRX,POM,1,3 |
| Парткод: | JC66-00991A |
| Деталь: | OTHER MECHA-M COLLAR DP, SCX-6345N/XRX,PO |
| Парткод: | JC67-00116A |
| Деталь: | DRIVE FUSER, SCX-6555N,SEC |
| Парткод: | JC93-00169A |
| Деталь: | MOTOR STEP, M42SP-4NK,CLX-8380ND/XAA,0.6A |
| Парткод: | JC31-00077A |
| Деталь: | PMO-IMPELLER_DRV, ML-6200,PA66,18,5mm,VO, |
| Парткод: | JC72-00825A |
| Деталь: | MOTOR STEP, M49SP-2NK,SCX-6555N,1.2A,1150 |
| Парткод: | JC31-00100A |
| Деталь: | GEAR-EXIT IDLE C, SCX-6555N,L1724KH,0.5/1 |
| Парткод: | JC66-01987A |
| Деталь: | GEAR-M_EXIT IDLE A, SCX-6345N/XRX,POM,A:1 |
| Парткод: | JC66-00996A |
| Деталь: | GEAR-M_FUSER IDLE A, SCX-6345N/XRX,POM,A: |
| Парткод: | JC66-00995A |
| Деталь: | FUSER, M5370,SEC,WORLD,110V |
| Парткод: | JC91-01159A |
| Деталь: | FUSER, M5370,SEC,WORLD,220V |
| Парткод: | JC91-01160A |
| Деталь: | HARNESS-FUSER_FU, SCX-6555N,UL3122,3P/1P, |
| Парткод: | JC39-00831A |
| Деталь: | THERMOSTAT, 125/250VAC,200,170+-5C,200,10 |
| Парткод: | 4712-001028 |
| Деталь: | PBA-FUSER_CRUM, SCX-6555N,SEC,EXPORT,-,-, |
| Парткод: | JC92-02008A |
| Деталь: | THERMISTOR-NTC ASSY, 7Kohm,3370K |
| Парткод: | 1404-001453 |
| Деталь: | LAMP-HALOGEN, 115V,1300W,13x9.8x276 |
| Парткод: | 4713-001521 |
| Деталь: | LAMP-HALOGEN, 230V,1300W,13x9.8x276 |
| Парткод: | 4713-001522 |
| Цена: | 3 900 ₽ |
| Деталь: | LEG-M ACTUATOR EXIT, SCX-6345N/XRX,PA,3,2 |
| Парткод: | JC61-01384B |
| Деталь: | GEAR-M DRV Z2228, SCX-6345N/XRX,NYLON66,A |
| Парткод: | JC66-01011A |
| Деталь: | GEAR-FUSER, SCX-6555N,PPS+GF40%,1.0,51,BR |
| Парткод: | JC66-01666A |
| Деталь: | ROLLER-PRESSURE, SCX-6555N,38,SUM22, STKM |
| Парткод: | JC66-01825A |
| Деталь: | GUIDE-M_INPUT JF, SCX-6345N/XRX,PET+GF,T3 |
| Парткод: | JC61-01419A |
| Деталь: | LEVER-JAM R, SCX-6555N,NYLON,T2,V0,BLK |
| Парткод: | JC66-01687A |
| Деталь: | LEVER-JAM L, SCX-6555N,NYLON66,T2,V0,BLK |
| Парткод: | JC66-01859A |
| Деталь: | GROUND-PR2, SCX-6555N,SUS,0.2,GROUND/UNC |
| Парткод: | JC63-01640A |
| Деталь: | COVER-M_GROUND, SCX-6345N/XRX,PET+GF30%,T |
| Парткод: | JC63-00761A |
| Деталь: | GROUND-P-PR, SCX-6345N/XRX,SUS 301 1/2H,0 |
| Парткод: | JC63-00819A |
| Деталь: | ROLLER FUSER-HEAT, M5370,22.43,AL,0.7T,PF |
| Парткод: | JC66-04148A |
| Деталь: | GUIDE-M_PICKUP BASE, SCX-6345N/XRX,ABS,T2 |
| Парткод: | JC61-01313A |
| Деталь: | SPRING-TS, SUS304-WPB,PI1.2,D11.2,L25/18. |
| Парткод: | 6107-001263 |
| Деталь: | MEA UNIT-RETARD, SCX-6345N/XRX,XEROX,-,RE |
| Парткод: | JC97-02290A |
| Деталь: | GUIDE-M_FEED IDLE MP, SCX-6345N/XRX,ABS,T |
| Парткод: | JC61-01297A |
| Деталь: | MEA UNIT-FEED IDLE MP, SCX-6345N,XEROX,-, |
| Парткод: | JC97-02705A |
| Деталь: | SPEAKER, 0.3W,8Ohm,81dB,400Hz |
| Парткод: | 3001-002207 |
| Деталь: | MEA UNIT-ROLLER PU, SCX-6345N/XRX,XEROX,- |
| Парткод: | JC97-02259A |
| Цена: | 240 ₽ |
| Деталь: | JOINT-M_RETARD, SCX-6345,POM,D18.4, L10.7 |
| Парткод: | JC66-00976A |
| Деталь: | COUPLER-TORQUELIMITER, SCX-6345N/XRX,OTLV |
| Парткод: | JC67-00126A |
| Деталь: | ROLLER-RUBBER IDLE, SCX-6345N,EPDM,SUM22, |
| Парткод: | JC66-01027A |
| Деталь: | HOLDER-M_BUSHING IDLE, SCX-6345N/XRX,POM, |
| Парткод: | JC61-01434A |
| Деталь: | SPRING ETC-TR R HAWK, ML-6060A,SUS 304 WP |
| Парткод: | JC61-00046A |
| Деталь: | COVER-REAR DUMMY, CLX-8650,ABS,HF-0660I |
| Парткод: | JC63-03623A |
| Деталь: | PLATEN-UPPER, M5370,SEC |
| Парткод: | JC97-04419A |
| Деталь: | PLATEN-LOWER, M5370,SEC |
| Парткод: | JC97-04420A |
| Деталь: | PLATEN-DUMMY UPPER, M5370,SEC |
| Парткод: | JC97-04421A |
| Деталь: | CCDM, CLX-8650,SEC,600dpi,LED |
| Парткод: | JC97-04021A |
| Деталь: | PLATEN-HOLDER FFC, M5370 |
| Парткод: | JC97-04448A |
| Деталь: | ACTUATOR, SCX-5100,POM,HB,NTR,ACTUATOR |
| Парткод: | JC72-00755A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | PBA-SCAN JOINT, M5370,SEC,FR-4,2Layer |
| Парткод: | JC92-02673A |
| Деталь: | PLATEN-SENSOR APS, M5370,SEC |
| Парткод: | JC97-04573B |
| Деталь: | PLATEN-MOTOR SUB, CLX-8650ND,SEE |
| Парткод: | JC97-04120A |
| Деталь: | BELT-TIMING GEAR, 950-2GT-3,3 |
| Парткод: | 6602-003266 |
| Деталь: | COVER-SCAN LOWER, M5370,ABS,G32690,HF-066 |
| Парткод: | JC63-04434A |
| Деталь: | BRACKET-SCAN LOWER, STAINLESS-STS304,PRES |
| Парткод: | JC61-06080A |
| Деталь: | PBA-APS_IF, SCX-6555N,SEC,EXPORT,-,-,-,30 |
| Парткод: | JC92-02009A |
| Деталь: | PHOTO-INTERRUPTER, Infrared light,BULK |
| Парткод: | 0604-001464 |
| Деталь: | CASSETTE SUB-MAIN, M5370,SEC |
| Парткод: | JC90-01268A |
| Деталь: | COVER-CASSETTE, M5370,HIPS,SPLIT GRAY,HIP |
| Парткод: | JC63-04486A |
| Деталь: | CAP-M_HANDLE LEFT, SCX-6345N/XRX,PC,T2,12 |
| Парткод: | JC67-00123A |
| Деталь: | GUIDE-P-SIDE LEFT, SCX-6345N/XRX,SECC,T1. |
| Парткод: | JC61-01413A |
| Деталь: | PLATE-P-LEVER, SCX-6345N/XRX,EGI-SECC,T1. |
| Парткод: | JC61-01322A |
| Деталь: | FRAME-CASSETTE, M5370,HIPS,SPILIT GRAY,3, |
| Парткод: | JC61-01411C |
| Деталь: | GEAR-M_RACK, SCX-6345N/XRX,POM,1,24,NTR |
| Парткод: | JC66-00956A |
| Деталь: | GEAR-M_PINION 24, SCX-6345N/XRX,POM,1,24, |
| Парткод: | JC66-01020A |
| Деталь: | GUIDE-P-SIDE RIGHT, SCX-6345N/XRX,SECC,T1 |
| Парткод: | JC61-01414A |
| Деталь: | STOPPER-M_KNOCK UP, M4580,ABS,HF-0660I,SP |
| Парткод: | JC61-00832G |
| Деталь: | SHAFT-PLATE LEVER, SCX-6345N/XRX,POSCUT,L |
| Парткод: | JC66-00953A |
| Деталь: | GEAR-M_LIFT COUPLING, SCX-6345N/XRX,POM,1 |
| Парткод: | JC66-00955A |
| Деталь: | GEAR-M_LIFTING, SCX-6345N/XRX,POM,1.5,46, |
| Парткод: | JC66-00954A |
| Деталь: | BRACKET-P-LIFTING, SCX-6345N/XRX,SECC,1.6 |
| Парткод: | JC61-01394A |
| Деталь: | SUPPORT-M_PUSH PAPER, SCX-6345N/XRX,PC,T2 |
| Парткод: | JC61-01417A |
| Деталь: | SUPPORT-M_BAR PAPER, SCX-6345N/XRX,PC,T2. |
| Парткод: | JC61-01416A |
| Деталь: | GUIDE-REAR, M5370,ABS,47.2,59.8,HF-0660I, |
| Парткод: | JC61-01395C |
| Деталь: | LEVER-LENTH HANDLE, SCX-6345N,HIPS HB,2,4 |
| Парткод: | JC66-00202B |
| Деталь: | GUIDE-M_HOOK, SCX-6345N/XRX,HIPS,GREEN,PA |
| Парткод: | JC61-01304A |
| Деталь: | PLATE-P-KNOCK UP, SCX-6345N/XRX,EGI-SECC, |
| Парткод: | JC61-01412A |
| Деталь: | PAD-MP(PLUS), SCX-5315F,Urethan Sponge,90 |
| Парткод: | JC69-00494A |
| Деталь: | FRAME-HOUSING PLATE UPPER, M5370,SEC |
| Парткод: | JC93-00898A |
| Деталь: | GUIDE-M_FEED UPPER, SCX-6345N/XRX,ABS,T2, |
| Парткод: | JC61-01296A |
| Деталь: | GUIDE-P-SHIELD SMPS, M5370,EGI-SECC,T 1.0 |
| Парткод: | JC61-06100A |
| Деталь: | BRUSH-ANTISTATIC, SCX-6445,SUS FIBER,0.2, |
| Парткод: | JC67-00055C |
| Деталь: | FRAME, M5370,SEC |
| Парткод: | JC93-00928A |
| Деталь: | FRAME-HOUSING MP, M5370,SEC |
| Парткод: | JC93-00927A |
| Деталь: | ELA HOU-SIZE SENSOR, SCX-6555N,SEC,korea, |
| Парткод: | JC96-04906A |
| Деталь: | ELA HOU-UPPER DP, SCX-6555N,SEC,-,-,- |
| Парткод: | JC96-04907A |
| Деталь: | ELA HOU-BASE PLATE R, SCX-6555N,SEC,-,-,- |
| Парткод: | JC96-04908A |
| Деталь: | FRAME-HOLDER PAD, M5370,SEC |
| Парткод: | JC93-00937A |
| Деталь: | PBA SUB-CASSETTE, CLX-8380ND,SEC,SEC,CASS |
| Парткод: | JC92-01913A |
| Деталь: | PHOTO-INTERRUPTER, TR,DIP-4,BK |
| Парткод: | 0604-001415 |
| Цена: | 240 ₽ |
| Деталь: | CORE ROTOR, ML-7250,STAINLESS-STS301,0.2T |
| Парткод: | JC70-00192A |
| Деталь: | BRACKET, ML-7250,EGI-SECC,1.6T,PRESS |
| Парткод: | JC70-00195A |
| Деталь: | HOUSING-M_SIZE SENSOR, SCX-6345N/XRX,ABS, |
| Парткод: | JC61-01343A |
| Деталь: | MEA UNIT-ACT READY, SCX-6345N,XEROX,GB,-, |
| Парткод: | JC97-02704A |
| Деталь: | GUIDE-M_FEED DP, SCX-6345N/XRX,ABS,T 2.5, |
| Парткод: | JC61-01294A |
| Деталь: | MOTOR GEARED-P LIFT, 2.1rpm,1.5N.m,1/1513 |
| Парткод: | JC31-00045A |
| Деталь: | HARNESS-SCF_MAIN, Rushmore,UL10272,18p,GR |
| Парткод: | JC39-00780A |
| Деталь: | RMO-ADF RUBBER, SCX-1110F,Si Rubber,50,G3 |
| Парткод: | JB73-00052A |
| Цена: | 70 ₽ |
| Деталь: | SHEET-GUIDE MP, M5370,PET,0.125,TRANSPARE |
| Парткод: | JC63-04751A |
| Деталь: | HOLDER-M-ADF RUBBER UPPER, SCX-6320F,HIPS |
| Парткод: | JC61-00744A |
| Деталь: | RPR-PAD CASSETTE, ML-1510,Urethan Sponge, |
| Парткод: | JC73-00141A |
| Цена: | 80 ₽ |
| Деталь: | GUIDE-M_PAD LOWER, SCX-6345N/XRX,HIPS,T2. |
| Парткод: | JC61-01415A |
| Деталь: | DADF-OPEN, M5370 |
| Парткод: | JC97-04423A |
| Деталь: | DADF-SUB, M5370 |
| Парткод: | JC97-04424A |
| Деталь: | COVER-SIDE R, M5370,ABS,G32690,HF-0660I,S |
| Парткод: | JC63-04426A |
| Деталь: | DADF-PLATEN, M5370 |
| Парткод: | JC97-04426A |
| Деталь: | COVER-SIDE F, M5370,ABS,G32690,HF-0660I,S |
| Парткод: | JC63-04425A |
| Деталь: | DADF-HINGE L, M5370,SEC |
| Парткод: | JC97-04446A |
| Деталь: | DADF-HINGE R, M5370,SEC |
| Парткод: | JC97-04445A |
| Деталь: | DADF-FRAME MAIN, M5370 |
| Парткод: | JC97-04427A |
| Деталь: | DADF-STACKER, M5370 |
| Парткод: | JC97-04425A |
| Деталь: | GUIDE-TX STACKER, M5370,ABS,HF-0660I,GUID |
| Парткод: | JC61-06086A |
| Деталь: | GUIDE-RACK DOCU TX, M5370,POM,F20-02,GUID |
| Парткод: | JC61-06082A |
| Деталь: | PHOTO-INTERRUPTER, TR,DIP-4,BK |
| Парткод: | 0604-001415 |
| Цена: | 240 ₽ |
| Деталь: | ACTUATOR-PAPER_LENGTH, CLX-9201,ABS,22,65 |
| Парткод: | JC66-03209A |
| Деталь: | GUIDE-STACKER LOWER, M5370,ABS,HF-0660I,G |
| Парткод: | JC61-06087A |
| Деталь: | GUIDE-STACKER WIRE, SCX-6345N/XRX,STS304, |
| Парткод: | JC61-01438A |
| Деталь: | HVPS, 24V,21.6V26.4V,MAX 5KV,MAX-2.5KV,6 |
| Парткод: | JC44-00234A |
| Деталь: | HOLDER-HVPS, M5370,ABS+PC,BLACK,NH-1000T |
| Парткод: | JC61-06099A |
| Деталь: | SMPS-V1, CLX-9201,PSPN TYPE5-V1,AC-DC,275 |
| Парткод: | JC44-00093C |
| Деталь: | SHIELD-SMPS LOWER, M5370,EGI-SECC,0.8,SHI |
| Парткод: | JC63-04483A |
| Деталь: | OPE, M5370,SEC |
| Парткод: | JC97-04499A |
| Деталь: | CASSETTE SUB-MAIN, M5370,SEC |
| Парткод: | JC90-01268A |
| Деталь: | SMPS-FDB V1, M5370-FDB-V1,JC44-00159B,AC/ |
| Парткод: | JC44-00159B |
| Деталь: | SHIELD-BD FUSER, SCX-6555N,EGI-SECC,0.8,N |
| Парткод: | JC63-01645A |
| Деталь: | HINGE-OPE, SUM22 |
| Парткод: | JC61-06103A |
| Деталь: | COVER-SCAN HINGE, M5370,ABS,Split Brown B |
| Парткод: | JC63-04464A |
| Деталь: | PLATEN, M5370,SEC |
| Парткод: | JC97-04418A |
| Деталь: | SPONGE-WHITE, M5370,Polyurethane Form,Bla |
| Парткод: | JC63-04419A |
| Деталь: | LSU, SCX-6555FN,SEC,SEE,55,600DPI,4Beam,- |
| Парткод: | JC97-03624A |
| Деталь: | ELA HOU-EXIT, SCX-6555N,SEC,-,-,- |
| Парткод: | JC96-04892A |
| Деталь: | FRAME-BASE, M5370,SEC |
| Парткод: | JC93-00876A |
| Деталь: | FUSER, M5370,SEC,WORLD,110V |
| Парткод: | JC91-01159A |
| Деталь: | FUSER, M5370,SEC,WORLD,220V |
| Парткод: | JC91-01160A |
| Деталь: | DRIVE MAIN, SCX-6555N,SEC |
| Парткод: | JC93-00168A |
| Деталь: | DRIVE FUSER, SCX-6555N,SEC |
| Парткод: | JC93-00169A |
| Деталь: | FRAME-FAN DUCT, SCX-6555N,SEC,100MOHM |
| Парткод: | JC93-00173A |
| Деталь: | CLUTCH-5K Z32, SCX-6345N/XRX,POM+METAL,5k |
| Парткод: | JC66-00994A |
| Деталь: | CLUTCH-5K Z32, CLX-8380ND/XAA,POM+METAL,5 |
| Парткод: | JC66-00994B |
| Деталь: | DUPLEX SUB-SIDE, M5370,SEC |
| Парткод: | JC90-01270A |
| Деталь: | COVER, M5370,SEC |
| Парткод: | JC95-01896A |
| Деталь: | DADF, M5370 |
| Парткод: | JC97-04422A |
| Деталь: | PBA-MAIN, SCX-6555N,SEC,FR-4,6Layer |
| Парткод: | JC92-02661A |
| Деталь: | HDD, 320G,HTS543232A7A384,S63,H16,C16383, |
| Парткод: | JC59-00035A |
| Деталь: | HOLDER-M_HDD, SCX-6345N/XRX,ABS,T2,W114.1 |
| Парткод: | JC61-01389A |
| Деталь: | SENSOR, HSU-07F1V2-N,CLX-9201,045C,+3.3 |
| Парткод: | JC32-00015A |
| Деталь: | HOLDER-LIU, M5370,PC,BLACK,NH-1035 |
| Парткод: | JC61-06098A |
| Деталь: | ELA HOU-EXIT, SCX-6555N,SEC,-,-,- |
| Парткод: | JC96-04892A |
| Деталь: | HOLDER-M_ACT OUTBIN, SCX-6345N/XRX,PC,T2. |
| Парткод: | JC61-01392A |
| Деталь: | LEG-M LIMIT STACKING, SCX-6345N/XRX,PC,3, |
| Парткод: | JC61-01391A |
| Деталь: | ADJUST, SUS,L23,PI1.8,ADJUST/UNC |
| Парткод: | JC70-00064A |
| Деталь: | GUIDE-M_EXIT UPPER, SCX-6345N/XRX,ABS+PC, |
| Парткод: | JC61-01301A |
| Деталь: | GEAR-M_EXIT LOWER, SCX-6345N/XRX,POM,0.8, |
| Парткод: | JC66-01018A |
| Деталь: | GEAR-M_EXIT UPPER, SCX-6345N/XRX,POM,0.8, |
| Парткод: | JC66-01017A |
| Деталь: | BRUSH-ANTISTATIC, SCX-6445,SUS FIBER,0.05 |
| Парткод: | JC67-00694A |
| Деталь: | ROLLER-EXIT UPPER, SCX-6345N,EPDM |
| Парткод: | JC66-01015A |
| Деталь: | ROLLER-EXIT_LOWER, SCX-6345N,EPDM |
| Парткод: | JC66-01016A |
| Деталь: | ROLLER-EXIT DRV, SCX-6345N,EPDM |
| Парткод: | JC66-01014A |
| Деталь: | SPRING-TS, SWP B,PI0.5,D3.55,L12.93/6.5,W |
| Парткод: | 6107-001540 |
| Деталь: | ROLLER-M IDLE JF, SCX-6345N,POM |
| Парткод: | JC66-01013A |
| Деталь: | HARNESS-EXIT, SCX-6555N,UL10272,8P/3P,2P, |
| Парткод: | JC39-00788A |
| Деталь: | ELA HOU-SOLENOID DP, CLX-8380ND/XAA,-,KOR |
| Парткод: | JC96-03749B |
| Деталь: | GUIDE-M_EXIT DUPLEX, SCX-6345N/XRX,ABS,T2 |
| Парткод: | JC61-01303A |
| Деталь: | MEA-GATE SPONGE, SCX-6555N,SEC,-,-,- |
| Парткод: | JC97-03208A |
| Деталь: | GEAR-M_EXIT, SCX-6345N/XRX,POM,1,15,W10,B |
| Парткод: | JC66-01012A |
| Деталь: | GUIDE-M_EXIT LOWER, SCX-6345N/XRX,ABS+GF, |
| Парткод: | JC61-01302A |
| Деталь: | ELA HOU-GUIDE SIDE, SCX-6555N,SEC,-,-,-,- |
| Парткод: | JC96-04897A |
| Деталь: | FAN-TYPE 5, Type5,24,170mA,4.0mmH20,0.433 |
| Парткод: | JC31-00160A |
| Деталь: | FAN-TYPE 8, Type8,24,220mA,1.388m3/mi |
| Парткод: | JC31-00162A |
| Деталь: | LOCKER-M_FRONT, SCX-6345N/XRX,POM,BLACK,H |
| Парткод: | JC64-00198A |
| Деталь: | SPRING ETC-LOCKER TORSION, SCX-5100,SUS30 |
| Парткод: | JC61-00479A |
| Деталь: | SHAFT-HANDLE, SCX-6345N/XRX,POSCUT,L356.2 |
| Парткод: | JC66-00935A |
| Деталь: | LOCKER-M_REAR, SCX-6345N/XRX,POM,BLACK,HB |
| Парткод: | JC64-00199A |
| Деталь: | BRACKET-COVER DUP, ML-9400W,PC/ABS |
| Парткод: | JC61-00175A |
| Деталь: | ROLLER-DUPLEX, SCX-6345N,EPDM,SUM22,6 |
| Парткод: | JC66-00969A |
| Деталь: | BRACKET-P-DUPLEX, SCX-6345N/XRX,SECC,0.50 |
| Парткод: | JC61-01334A |
| Деталь: | ROLLER-DUPLEX READY, SCX-6345N,EPDM,SUM22 |
| Парткод: | JC66-00970A |
| Деталь: | GROUND-P-DUPLEX, SCX-6345N/XRX,STAINLESS- |
| Парткод: | JC63-00784A |
| Деталь: | BELT-TIMING GEAR, RUBBER,T1.36,40S2M338,3 |
| Парткод: | 6602-001092 |
| Деталь: | CLUTCH-2.5K Z24, CLX-8380ND/XAA,POM+METAL |
| Парткод: | JC66-01837A |
| Деталь: | OTHER MECHA-M COLLAR DP, SCX-6345N/XRX,PO |
| Парткод: | JC67-00116A |
| Деталь: | COVER-SIDE, M5370,HIPS,Split Gray,HIPS-51 |
| Парткод: | JC63-04472A |
| Деталь: | MOTOR DC, HF283LG,DC24V,CLX-8380ND/XAA,79 |
| Парткод: | JC31-00094A |
| Деталь: | GEAR-IDLE ENV, SCX-6555N,POM,0.4/0.7,70/1 |
| Парткод: | JC66-01665A |
| Деталь: | GEAR-CAM REAR, SCX-6555N,PC,0.7,14,BLK,SP |
| Парткод: | JC66-01684A |
| Деталь: | GEAR-DRIVE REAR, SCX-6555N,POM,0.4/0.6,20 |
| Парткод: | JC66-01685A |
| Деталь: | PHOTO-INTERRUPTER, TR,DIP-4,BK |
| Парткод: | 0604-001415 |
| Цена: | 240 ₽ |
| Деталь: | LEG-M_ACTUATOR DUPLEX, SCX-6345N/XRX,PC,2 |
| Парткод: | JC61-01336A |
| Деталь: | LEVER-GEAR FRONT, SCX-6555N,PC,BLACK,LINK |
| Парткод: | JC66-01686A |
| Деталь: | GUIDE-M_SIDE, SCX-6345N/XRX,ABS+PC,T2.5,2 |
| Парткод: | JC61-01289A |
| Деталь: | HOLDER-ARM RELEASE, CLX-9350,POM,29.13,55 |
| Парткод: | JC61-03231A |
| Деталь: | ROLLER-IDLE-OD16, CLX-9350,POM,16 |
| Парткод: | JC66-02293A |
| Деталь: | GROUND-HINGE_LEFT, CLX-8650ND,C521P,0.2,4 |
| Парткод: | JC63-03683A |
| Деталь: | PCB-ADF, CLX-8650ND,FR4,2,1.6,13060mm,4, |
| Парткод: | JC41-00776A |
| Деталь: | SHIELD-ADF BOARD, CLX-8650ND,EGI-SECC,0.8 |
| Парткод: | JC63-03685A |
| Деталь: | GROUND-HINGE_RIGHT, CLX-8650ND,PBS-C5210, |
| Парткод: | JC63-03684A |
| Деталь: | GUIDE-EXTENSION_S, CLX-8650ND,ABS,2.5,86. |
| Парткод: | JC61-05297A |
| Деталь: | GUIDE-EXTENSION S, M5370,ABS,HF-0660I,GUI |
| Парткод: | JC61-06083A |
| Деталь: | COVER-DUMMY RIGHT, M5370,ABS,G32690,HF-06 |
| Парткод: | JC63-04430A |
| Деталь: | COVER-DUMMY PLATEN, M5370,ABS,G32690,HF-0 |
| Парткод: | JC63-04431A |
| Деталь: | GUIDE-P-TR, SCX-6345N/XRX,SECC,T0.5,233mm |
| Парткод: | JC61-01290A |
| Деталь: | GUIDE-M_FEED, SCX-6345N/XRX,ABS,T2.5,287m |
| Парткод: | JC61-01292A |
| Деталь: | HOLDER-M_SAW, SCX-6345N/XRX,PC,T1.5,243,1 |
| Парткод: | JC61-01407A |
| Деталь: | CORE ROTOR, SCX-6320F,STAINLESS-STS304,0. |
| Парткод: | JC70-10232D |
| Деталь: | GUIDE-EARTH TR, SCX-6555N,SECC,T1,PATH |
| Парткод: | JC61-02760A |
| Деталь: | SPRING ETC-SPRING ETC FEED, ML-5000A,SUS3 |
| Парткод: | JC61-70959A |
| Деталь: | FRAME-ID SENSOR, SCX-6555N,SEC |
| Парткод: | JC96-05348B |
| Деталь: | BRUSH-ANTISTATIC, SCX-6445,SUS FIBER,0.05 |
| Парткод: | JC67-00694A |
| Деталь: | GUIDE-M_DUPLEX, SCX-6345N/XRX,ABS+PC,T2.5 |
| Парткод: | JC61-01293A |
| Деталь: | ROLLER-M IDLE JF, SCX-6345N,POM |
| Парткод: | JC66-01013A |
| Деталь: | TERMINAL-S_IDLE, SCX-6345N/XRX,SUS304WPB, |
| Парткод: | JC65-00012A |
| Деталь: | SENSOR-CTD, SENSOR-CTD,0 60,5V,6.62mA,r |
| Парткод: | JC32-00014A |
| Деталь: | HOLDER, SCX-6555N,PC,BLK,NH-1035 |
| Парткод: | JC61-02753A |
| Деталь: | HARNESS-CTD, Rushmore,UL10272,4p, 5P,GRAY |
| Парткод: | JC39-00797A |
| Деталь: | SPRING-TS, STAINLESS-STS304,0.35,ID4.6,OD |
| Парткод: | 6107-001261 |
| Деталь: | HOLDER-CTD, SCX-6555N,ABS,BLK |
| Парткод: | JC61-02259A |
| Деталь: | DADF-PICK UP, M5370 |
| Парткод: | JC97-04428A |
| Деталь: | DADF-GUIDE PICK UP, CLX-8650ND,SEE |
| Парткод: | JC97-04103A |
| Деталь: | DSDF-CCDM, M5370,SEC |
| Парткод: | JC97-04571A |
| Деталь: | BELT-TIMING GEAR, 40S2M326,RUBBER,0.6,326 |
| Парткод: | 6602-003273 |
| Деталь: | CLUTCH-ELECTRIC, 2.5,24,1,120mA,200Ohm |
| Парткод: | JC47-00033A |
| Цена: | 1 200 ₽ |
| Деталь: | BELT-TIMING GEAR, 80S2M264,RUBBER,0.6,264 |
| Парткод: | 6602-003272 |
| Деталь: | BELT-TIMING GEAR, 60S2M138,RUBBER,0.6,138 |
| Парткод: | 6602-003271 |
| Деталь: | BELT-TIMING GEAR, 40S2M134,RUBBER,0.6,134 |
| Парткод: | 6602-003274 |
| Деталь: | PHOTO-INTERRUPTER, TR,DIP-4,BK |
| Парткод: | 0604-001415 |
| Цена: | 240 ₽ |
| Деталь: | MOTOR STEP 1P, 24V,1.3A |
| Парткод: | JC31-00163A |
| Деталь: | GUIDE-EXIT UPPER, CLX-8650ND,ABS,2,44.7,2 |
| Парткод: | JC61-05292A |
| Деталь: | DADF-GUIDE FEED IN, CLX-8650ND,SEE |
| Парткод: | JC97-04102A |
| Деталь: | FRAME-BRIDGE EXIT, CLX-8650ND,EGI-SECC,1. |
| Парткод: | JC61-05307A |
| Деталь: | GUIDE-REGI, CLX-8650ND,ABS,77.1,235.5,BLA |
| Парткод: | JC61-05295A |
| Деталь: | DADF-GUIDE EXIT LOWER, CLX-8650ND,SEE |
| Парткод: | JC97-04104A |
| Деталь: | DSDF-PICK UP ROLLER, CLX-8650ND,SEC |
| Парткод: | JC97-04099A |
| Деталь: | PAD-GUIDE PICKUP, SCX-6555N,Urethan Spong |
| Парткод: | JC69-01326A |
| Деталь: | DAMPER-RETARD MP, CLX-8650ND,NBR,1.1,21.1 |
| Парткод: | JC66-03759A |
| Деталь: | DADF-RETARD ROLLER, CLX-8650ND,SEE |
| Парткод: | JC97-04135A |
| Деталь: | STOPPER-PICK UP, CLX-8650ND,ABS+PC,37.6,1 |
| Парткод: | JC61-05363A |
| Деталь: | DSDF-SEPARATION SUB ROLLER, CLX-8650ND,SE |
| Парткод: | JC97-04148A |
| Деталь: | PLATE-P-BEAM BASE, SCX-6345N/XRX,EGI-SECC |
| Парткод: | JC61-01312A |
| Деталь: | HOUSING-BASE LEFT, ABS,split gray,HF-0660 |
| Парткод: | JC61-01342C |
| Деталь: | ELA HOU-PICK UP, SCX-6555N,SEC,ASSY SPEAK |
| Парткод: | JC96-05046A |
| Деталь: | HARNESS-SCF_EMPTY, Rushmore,UL10272,8P,3P |
| Парткод: | JC39-00794A |
| Деталь: | PHOTO-INTERRUPTER, TR,DIP-4,BK |
| Парткод: | 0604-001415 |
| Цена: | 240 ₽ |
| Деталь: | HARNESS-MOTOR_SW, Rushmore,UL10272,2P,300 |
| Парткод: | JC39-00833A |
| Деталь: | LEG-M_ACT NO PAPER, SCX-6345N/XRX,ABS,2,3 |
| Парткод: | JC61-01350A |
| Деталь: | MEA UNIT-ROLLER PU, SCX-6345N/XRX,XEROX,- |
| Парткод: | JC97-02259A |
| Цена: | 240 ₽ |
| Деталь: | GEAR-M_PU JOINT, SCX-6345N/XRX,POM,0.7,21 |
| Парткод: | JC66-00943A |
| Деталь: | GEAR-M_IDLE PU, SCX-6345N/XRX,POM,0.7,22, |
| Парткод: | JC66-00940A |
| Деталь: | MEA UNIT-IDLE FORWARD, SCX-6345N/XRX,XERO |
| Парткод: | JC97-02292A |
| Деталь: | MEA UNIT-GEAR ONE WAY, SCX-6345N/XRX,XERO |
| Парткод: | JC97-02291A |
| Деталь: | GUIDE-M_UPPER PICK UP, SCX-6345N/XRX,PC,T |
| Парткод: | JC61-01299A |
Коды ошибок
11-2T01, 11-2T11, 11-2T21
11-2T31, 11-2T41, 11-2T61
61-1111
A1-1111, A1-1112, A1-1113
A1-3111, A1-3112, A1-3113
A3-2113
A3-3210, A3-3211, A3-3212
A3-3310, A3-3311, A3-3312
A3-3320, A3-3410
A3-3411, A3-3412
A4-1110
C1-1110
C1-111A, C1-1313, C1-1314
C1-1140, C1-1160, C1-1170
C1-1410
C1-1512
C1-1710, C1-1711, C1-1712
C3-1110
C3-1140 C3-1150 C3-1170
C3-1210
C3-1314, C3-1315, C3-1316
C3-1410, C3-1414, C3-1512
C3-1710, C3-1711, C3-1712
C6-1120
C9-1112, C9-1122
C9-1132, C9-1142
C9-1162
C9-2120
C9-2220
H1-1211, H1-1213
H1-1217, H1-1218, H1-1219
H1-1220
H1-1222, H1-1240
H1-1230
H1-1251, H1-1252
H1-1253
H1-1311, H1-1313
H1-1317, H1-1318, H1-1319
H1-1320
H1-1322, H1-1340
H1-1332
H1-1351, H1-1352
H1-1353
H1-1411, H1-1413
H1-1417, H1-1418, H1-1419
H1-1420
H1-1422
H1-1434
H1-1451, H1-1452
H1-1453
H1-2211, H1-2213
H1-2217, H1-2218, H1-2219
H1-2220
H1-2222, H1-2240
H1-2230
H1-2251, H1-2252
H1-2253
H2-5001, H2-5002, H2-5096
H2-5003, H2-5004, H2-5097
H2-5005, H2-5006, H2-5098
H2-5007, H2-5008, H2-5099
H2-5009, H2-5010
H2-5011, H2-5100
H2-5012, H2-5013, H2-5101
H2-5014, H2-5015, H2-5102
H2-5032
H2-5033, H2-5035, H2-5036
H2-5034, H2-5037
H2-5048
H2-506x, H2-507x, H2-5A50
H2-5080 ... H2-5085
H2-5086, H2-5087
H2-5088
H2-5112, H2-5113
H2-5A21
H2-5A31, H2-5A32
H2-5A34, H2-5A35
H2-5A38 ... H2-5A49
H2-5A50, H2-6A50
H2-5A62, H2-5A63
H2-5A90
H2-6A62, H2-6A63
M1-1113
M1-1613
M1-3122
M1-4111
M1-5111, M1-5112, M1-5120
M1-5612
M2-1111, M2-1114
M2-1117, M2-2111
M2-2112, M2-2114
M2-2311, M2-2312, M2-2314
M3-1111, M3-1112, M3-1114
M3-2130
S1-1313
S1-2411
S1-2433, S1-244x
S1-2434, S1-2435, S1-2436
S1-2437, S1-2438, S1-2439
S1-2510, S1-2521
S1-2523, S1-2530
S2-1211
S2-331D
S2-3321
S2-3421
S2-4120
S3-3121
S3-3211
S5-3111
S6-3122
S6-3123, S6-3229, S6-322A
S6-3128
S6-3224, S6-3225
S6-3226, S6-3227
S7-1110
S7-1210
S7-2110
U1-2115
U1-2117, U1-212x
U1-213x, U1-23xx
U1-234J, U1-234P
U2-1112
U2-1113
U3-3211, U3-3213, U3-3214
U3-3311, U3-3313, U3-3314
U3-3411, U3-3413, U3-3414
U3-3511, U3-3513, U3-3514
U3-3611, U3-3613, U3-3614
U3-3713, U3-3714
Описание
| Error code: | 11-2T01, 11-2T11, 11-2T21 |
| Display: | Tray paper mismatch Tray 1 paper mismatch Tray 2 paper mismatch Tray 3 paper mismatch Tray 4 paper mismatch MP tray paper mismatch |
| Description: | Load tray with [Letter], [Plain] paper Load tray 1 with [Letter], [Plain] paper Load tray 2 with [Letter], [Plain] paper Load tray 3 with [Letter], [Plain] paper Load tray 4 with [Letter], [Plain] paper Load MP with [Letter], [Plain] paper |
| Causes: | Paper in tray is not matched to the machine paper setting. |
| Remedy: | 1) Check and change the paper setting of the corresponding tray properly. |
| Error code: | 11-2T31, 11-2T41, 11-2T61 |
| Display: | Tray paper mismatch Tray 1 paper mismatch Tray 2 paper mismatch Tray 3 paper mismatch Tray 4 paper mismatch MP tray paper mismatch |
| Description: | Load tray with [Letter], [Plain] paper Load tray 1 with [Letter], [Plain] paper Load tray 2 with [Letter], [Plain] paper Load tray 3 with [Letter], [Plain] paper Load tray 4 with [Letter], [Plain] paper Load MP with [Letter], [Plain] paper |
| Causes: | Paper in tray is not matched to the machine paper setting. |
| Remedy: | 1) Check and change the paper setting of the corresponding tray properly. |
| Error code: | 61-1111 |
| Description: | Booting Failure: #61-1111. Turn off then on. Call for service if the problem persists |
| Causes: | Hibernation image creation is failed. |
| Remedy: | 1) Turn the machine on with a normal booting. 2) Enter the SVC mode. Select “Hibernation On” again. |
| Error code: | A1-1111, A1-1112, A1-1113 |
| Description: | Motor Failure: #A1-1111. Turn off then on. Call for service if the problem persists Motor Failure: #A1-1112. Turn off then on. Call for service if the problem persists Motor Failure: #A1-1113. Turn off then on. Call for service if the problem persists |
| Causes: | Main motor operation is abnormal. |
| Remedy: | • A1–1111 : Main motor is stopped but machine recognizes it as operational. • A1–1112 : Main motor is not operated for print-job. • A1–1113 : Main motor is operating but machine recognizes status as "Stopped". 1) Turn the machine off. Check if there are any foreign substances or paper around the paper path. 2) Remove the rear cover after removing 6 screws. 3) Check if the main motor connector is connected correctly. 4) If the connection is OK, turn the machine on. Enter SVC mode. Select the main motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the main motor(JC31-00090A) • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)). - If the control signal is abnormal, replace the main board(JC92–02661A) b) If the motor is operational, • Check the Pin No 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness. |
| Error code: | A1-3111, A1-3112, A1-3113 |
| Description: | Motor Failure: #A1-3111. Turn off then on. Call for service if the problem persists Motor Failure: #A1-3112. Turn off then on. Call for service if the problem persists Motor Failure: #A1-3113. Turn off then on. Call for service if the problem persists |
| Causes: | Dev motor operation is abnormal. |
| Remedy: | • A1–3111 : Dev motor is stopped but machine recognizes it as operational. • A1–3112 : Dev motor is not operated for print-job. • A1–3113 : Dev motor is operating but machine recognizes status as "Stopped". 1) Turn the machine off. Check if there are any foreign substances or paper around the imaging unit. 2) Remove the rear cover after removing 6 screws. 3) Check if the Dev motor connector is connected correctly. 4) If the connection is OK, turn the machine on. Enter SVC mode. Select the Dev motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the Dev motor(JC31-00090A) • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board(JC44-00100C (220V) / JC44-00093C (110V)). - If the control signal is abnormal, replace the main board(JC92–02661A) b) If the motor is operational, • Check the Pin No 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness. |
| Error code: | A3-2113 |
| Display: | The CTD sensor is dirty. Please clean it with soft cloth or paper(A3-2113) |
| Description: | The CTD sensor is dirty. Please clean it with soft cloth or paper. |
| Causes: | CTD sensor is defective or CTD sensor calibration is abnormal. |
| Remedy: | 1) Turn the machine off. 2) Open the side cover. 3) Check if the CTD sensor window is contaminated. If yes, clean the window with soft cloth. 4) Close the side cover. 5) Turn the machine on. 6) If the problem persists, replace the CTD sensor (JC32-00014A). |
| Error code: | A3-3210, A3-3211, A3-3212 |
| Display: | Sensor Failure: #. Turn off then on. Call for service if the problem persists. |
| Description: | Sensor Failure: #A3-3210. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3211. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3212. Turn off then on. Call for service if the problem persists |
| Causes: | Inner temperature sensor is defective. • A3–3210 : Inner temperature sensor value is abnormal. • A3–3211 : Inner temperature sensor is in short status. • A3–3212 : Inner temperature sensor is in open status. |
| Remedy: | 1) Open the side cover. Check the connection. • If the connection is OK, replace the photo sensor (1404-001417). 2) If the sensor is normal, replace the main board(JC92-02742A). |
| Error code: | A3-3310, A3-3311, A3-3312 |
| Display: | Sensor Failure: #A3-3310. Turn off then on. Call for service if the problem persists. Actuator Fan Failure #: Turn off then on. |
| Description: | Sensor Failure: #A3-3310. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3311. Turn off then on. Call for service if the problem persists Sensor Failure: #A3-3312. Turn off then on. Call for service if the problem persists |
| Causes: | Outer temperature/humidity sensor is defective. • A3–3310 / A3–3311 / A3–3312 : Temperature function is abnormal. • A3–3410 / A3–3411 / A3–3412 : Humidity function is abnormal. |
| Remedy: | 1) Remove the left cover. Unplug and reconnect the sensor harness. If the error persists, replace the sensor(JC93-00486A). 2) If the harness and sensor are normal, replace the main board (JC92-02742A). |
| Error code: | A3-3320, A3-3410 |
| Description: | The room temperature is not suitable for this set use. Please adjust room temperature Sensor Failure: #A3-3410. Turn off then on. Call for service if the problem persists. |
| Causes: | Outer temperature/humidity sensor is defective. |
| Remedy: | • A3–3310 / A3–3311 / A3–3312 / A3–3320 : Temperature function of the sensor is abnormal. • A3–3410 / A3–3411 / A3–3412 : Humidity function of the sensor is abnormal. 1) Enter SVC mode. Execute sensor test to check its operation. (Diagnostics > Engine Diagnostics > Engine Test Routines > 109-0013 Outer Temperature ) 2) Remove the left cover. Measure the resistance value of the connector at both ends. If the value is not in 47.5KΩ ~ 52.5KΩ (@ 25°C), replace the outer temperature/humidity sensor(JC32–00015A). 3) If the harness and sensor are normal, replace the main board(JC92–02661A). |
| Error code: | A3-3411, A3-3412 |
| Display: | A3-3311, A3-3312, A3-3320, A3-3411, A3-3412 Sensor errors |
| Description: | Sensor Failure: #A3-3411. Turn off then on. Call for service if the problem persists. Sensor Failure: #A3-3412. Turn off then on. Call for service if the problem persists. |
| Causes: | Outer temperature/humidity sensor is defective. |
| Remedy: | • A3–3310 / A3–3311 / A3–3312 / A3–3320 : Temperature function of the sensor is abnormal. • A3–3410 / A3–3411 / A3–3412 : Humidity function of the sensor is abnormal. 1) Enter SVC mode. Execute sensor test to check its operation. (Diagnostics > Engine Diagnostics > Engine Test Routines > 109-0013 Outer Temperature ) 2) Remove the left cover. Measure the resistance value of the connector at both ends. If the value is not in 47.5KΩ ~ 52.5KΩ (@ 25°C), replace the outer temperature/humidity sensor(JC32–00015A). 3) If the harness and sensor are normal, replace the main board(JC92–02661A). |
| Error code: | A4-1110 |
| Display: | Lamp Failure: #A4-1110. Open the door, then close it. Call for service if the problem persists |
| Description: | Erase Lamp does not turn on. |
| Causes: | Erase Lamp does not turn on. |
| Remedy: | 1) Enter SVC mode. Execute the erase lamp test. (Diagnostics > Engine Diagnostics > Engine Test Routines > Erase Lamp) 2) If the erase lamp does not turn on, replace it(JC92-02373A). |
| Error code: | C1-1110 |
| Display: | Prepare new yellow toner cartridge. |
| Description: | Toner remained is 5 - 30% of its life. |
| Causes: | Toner cartridge is almost empty. |
| Remedy: | 1) Open the front cover. 2) Remove the toner cartridge(MLT-D709S). (Toner cartridge with level of “Low” will be exhausted soon.) |
| Error code: | C1-111A, C1-1313, C1-1314 |
| Description: | Shake toner cartridge and then install. Replace toner cartridge if the problem persists. Shake toner cartridge and then install. Call for service if the problem persists. Did not supply enough toner. Remove seal tape of toner cartridge or shake it. Call for service if the problem persists. |
| Causes: | Toner remained of the toner cartridge is low. / Toner supply is abnormal. |
| Remedy: | 1) Open the front cover and side cover. 2) Remove the toner cartridge. 3) Check if the toner cartridge seal is removed. If not, remove it. 4) Shake the toner cartridge horizontally to distribute the toner evenly inside the cartridge. 5) Reinstall the toner cartridge. 6) If the problem persists, replace the toner cartridge. |
| Error code: | C1-1140, C1-1160, C1-1170 |
| Display: | C1-1140, C1-1160, C1-1170 Toner errors |
| Description: | End of life, Replace with new toner cartridge. Replace with new toner cartridge. |
| Causes: | Toner cartridge is at the end of its life. |
| Remedy: | 1) Open the front cover and side cover. 2) Remove the toner cartridge. 3) Install the new toner cartridge. 4) Close the front cover. |
| Error code: | C1-1410 |
| Display: | Toner cartridge is not installed. Install the cartridge. |
| Description: | The toner cartridge is not installed. / The machine can’t detect the toner cartridge. |
| Causes: | Toner cartridge is not installed. |
| Remedy: | 1) Turn the machine off then on. 2) Remove the toner cartridge. Thoroughly roll the cartridge five or six times to distribute the toner evenly inside the cartridge. And reinstall the toner cartridge. 3) Check if the CRUM contact area is contaminated. Clean it. |
| Error code: | C1-1512 |
| Display: | Toner cartridge is not compatible. Check users guide. |
| Description: | Toner cartridge is not compatible. Check users guide. |
| Causes: | Toner cartridge is not compatible. |
| Remedy: | 1) Print the supply information report. Check information of the toner cartridge. 2) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one. |
| Error code: | C1-1710, C1-1711, C1-1712 |
| Display: | Error: #C1-1710 Call for Service Error: #C1-1711 Call for Service Error: #C1-1712 Call for Service |
| Description: | The machine can’t detect the CRUM chip of the toner cartridge. |
| Causes: | The data of CRUM is not detected. / CRUM is defective. |
| Remedy: | NOTE These errors are for M3325/3825/4025. 1) Open the front cover. 2) Remove the toner cartridge. 3) Check if the CRUM terminal is contaminated. Clean it. 4) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one. |
| Error code: | C3-1110 |
| Display: | Prepare IMG. Unit / Prepare new imaging unit Replace IMG. Unit / Replace with new imaging unit |
| Description: | The remaining imaging unit is less than 10% / The imaging unit is at the end of its life. |
| Causes: | Imaging unit has almost reached the end of its life. |
| Remedy: | These errors are for M3325/3825/4025. Check the life remaining of the imaging unit. If its life is at the end, turn the machine off and replace the imaging unit with new one. |
| Error code: | C3-1140 C3-1150 C3-1170 |
| Description: | End of life, Replace with new imaging unit. Replace with new imaging unit End of life, Replace with new imaging unit. |
| Causes: | Imaging unit is at the end of its life. |
| Remedy: | 1) Open the front cover and side cover. 2) Remove the toner cartridge. 3) Remove the imaging unit and replace it with new one. 4) Install the toner cartridge. 5) Close the side cover and front cover. |
| Error code: | C3-1210 |
| Description: | Imaging Unit Failure:#C3-1210. Please turn off then on. |
| Causes: | Sensor calibration error that detects the toner density for image stabilization control has occurred. |
| Remedy: | 1) Open the front cover and side cover. 2) Remove the toner cartridge. 3) Remove and reinstall the imaging unit. 4) Install the toner cartridge. 5) Close the side cover and front cover. 6) If the problem persists, replace the imaging unit. |
| Error code: | C3-1314, C3-1315, C3-1316 |
| Description: | Imaging Unit Failure: #C3-1314. Install imaging unit again Imaging Unit Failure: #C3-1315. Install imaging unit again Imaging Unit Failure: #C3-1316. Install imaging unit again |
| Causes: | Toner supply is abnormal. |
| Remedy: | 1) Open the front cover and side cover. 2) Remove the toner cartridge. 3) Remove and reinstall the imaging unit. 4) Install the toner cartridge. 5) Close the side cover and front cover. 6) If the problem persists, replace the imaging unit. 7) Check if the motor related to toner supply is working normally. If not, replace the motor. |
| Error code: | C3-1410, C3-1414, C3-1512 |
| Description: | Imaging unit is not installed. Install the unit. Imaging Unit Failure: #C3-1414. Install imaging unit again. Imaging unit is not compatible. Check users guide. |
| Causes: | Imaging unit is not installed properly. / The machine can’t read the charger resistance value from the imaging unit. / Imaging unit is not compatible. |
| Remedy: | 1) Open the front cover and side cover. 2) Remove the toner cartridge. 3) Remove and reinstall the imaging unit. 4) Install the toner cartridge. 5) Close the side cover and front cover. 6) If the problem persists, replace the imaging unit with new one. |
| Error code: | C3-1710, C3-1711, C3-1712 |
| Description: | Imaging unit Failure: #C3-1710. Call for service. Imaging unit Failure: #C3-1711. Call for service. Imaging unit Failure: #C3-1712. Call for service. |
| Causes: | The data of CRUM is not detected. |
| Remedy: | 1) Open the front cover and side cover. 2) Remove the imaging unit check that its modular jack is contaminated or deformed. 3) If it is defective, replace it with new one. 4) Close the side cover and front cover. |
| Error code: | C6-1120 |
| Display: | Replace new Fuser unit |
| Description: | Replace with new fuser unit |
| Causes: | The life of the fuser unit has expired. |
| Remedy: | 1) Turn the machine off. 2) Replace the fuser unit(JC91-01157A (220V) /JC91-01158A (110V)). 3) Turn the machine on. |
| Error code: | C9-1112, C9-1122 |
| Description: | Replace with new Tray1 pickup roller. Replace with new Tray2 pickup roller. |
| Causes: | The life of the pick up/reverse/forward roller for tray1,2,3,4 has expired. |
| Remedy: | 1) Open the side cover. 2) Remove the cassette. 3) Lift small tap, remove the pick up / reverse/ forward roller. 4) Install the new pick up / reverse/ forward roller. 5) Enter SVC mode. 6) Select “Roller” (INFORMATION > Supply Status > Field Replacement Unit > Roller) 7) Select “P/up roller Kit-tray1~4”. The “RESET” button will be activated. Click “RESET” to clear the corresponding pick up roller. 8) Exit SVC mode by pushing the home button. |
| Error code: | C9-1132, C9-1142 |
| Description: | Replace with new Tray3 pickup roller. Replace with new Tray4 pickup roller. |
| Causes: | The life of the pick up/reverse/forward roller for tray1,2,3,4 has expired. |
| Remedy: | 1) Open the side cover. 2) Remove the cassette. 3) Lift small tap, remove the pick up / reverse/ forward roller. 4) Install the new pick up / reverse/ forward roller. 5) Enter SVC mode. 6) Select “Roller” (INFORMATION > Supply Status > Field Replacement Unit > Roller) 7) Select “P/up roller Kit-tray1~4”. The “RESET” button will be activated. Click “RESET” to clear the corresponding pick up roller. 8) Exit SVC mode by pushing the home button. |
| Error code: | C9-1162 |
| Display: | Replace with new MP pickup roller |
| Description: | Replace new MP Pickup roller |
| Causes: | The MP pick up roller is at the end of its life. |
| Remedy: | 1) Turn the machine off. 2) Replace the MP pick up roller. |
| Error code: | C9-2120 |
| Description: | Replace with new Transfer roller |
| Causes: | The life of the second transfer roller(T2) expires soon or has expired. |
| Remedy: | 1) Open the side cover. 2) Replace the second transfer roller with new one. 3) Close the side cover. 4) Enter SVC mode. 5) Select “TRNASFER” (INFORMATION > Supply Status > Field Replacement Unit > TRNASFER) 6) Select “T2 Roller”. The “RESET” button will be activated. Click “RESET” to clear the T2 roller. 7) Exit SVC mode by pushing the home button. |
| Error code: | C9-2220 |
| Display: | TR Failure: #C9-2220. Install transfer roller again. |
| Description: | TR Failure: #C9-2220. Install transfer roller again |
| Causes: | The life of the second transfer roller(T2) is not installed. |
| Remedy: | 1) Open the side cover. 2) Remove and reinstall the second transfer roller. 3) Close the side cover. 4) If the problem persists, replace the HVPS board(JC44–00212A). |
| Error code: | H1-1211, H1-1213 |
| Description: | Paper jam in Tray 2. Paper jam in tray 2 or tray door is open. |
| Causes: | Paper jam has occurred in tray2. (Pick up unit connection is defective. / Pickup rollers are defective. / Pick up sensor is defective.) |
| Remedy: | 1) Remove the tray2. Remove the jammed paper. And install the tray2. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers. 5) Check the tray 2 pick up unit. • Check if the sensor and actuator are assembled correctly. When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor. • If there is a defective part like a actuator, spring etc., replace it or the tray 2 pick up unit. 6) Check if the tray 2 pick up motor connector is connected correctly. 7) If the pick up motor is defective, replace it. 8) Check if the tray 2 pick up clutch connector is connected correctly. |
| Error code: | H1-1217, H1-1218, H1-1219 |
| Description: | Paper jam in Tray 2. Paper jam in tray 2 or tray door is open. |
| Causes: | Paper jam has occurred in tray2. (Pick up unit connection is defective. / Pickup rollers are defective. / Pick up sensor is defective.) |
| Remedy: | 1) Remove the tray2. Remove the jammed paper. And install the tray2. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers. 5) Check the tray 2 pick up unit. • Check if the sensor and actuator are assembled correctly. When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor. • If there is a defective part like a actuator, spring etc., replace it or the tray 2 pick up unit. 6) Check if the tray 2 pick up motor connector is connected correctly. 7) If the pick up motor is defective, replace it. 8) Check if the tray 2 pick up clutch connector is connected correctly. |
| Error code: | H1-1220 |
| Display: | Tray 2 Door Open. Close it |
| Description: | Optional cassette is not installed properly |
| Causes: | Tray 2 door is open. |
| Remedy: | 1) Remove and reinstall the Tray2 cassette. 2) Check the cassette detection sensor. • Check if the connection between sensor and main board is OK. Reconnect the harness. • If the sensor(JC34-00001A) is defective, replace it. 3) If the problem persists, replace the SCF main board(JC92-02636A). |
| Error code: | H1-1222, H1-1240 |
| Description: | Tray 2 cassette is pulled out. Insert it properly. |
| Causes: | Tray 2 is pulled out or the cassette detection sensor connector is not connected or broken. |
| Remedy: | 1) Remove and insert tray2 correctly. 2) If the problem persists, remove tray2 again. 3) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the cassette detection sensor. 5) If the problem persists, replace the SCF board. |
| Error code: | H1-1230 |
| Display: | Error: #H1-1230 / Input System Failure: #H1-1230. Check tray 2 connection |
| Description: | Communication error has occurred. |
| Causes: | The communication error between the tray 2 and the main machine has occurred. |
| Remedy: | 1) Turn the machine off then on. 2) If the problem persists, turn the machine off. 3) Remove the SCF right cover. (Refer to 3.3.23.1) 4) Check if the interface connector is connected to the SCF main board. If the interface connector is defective, replace it. 5) If the problem persists, replace the SCF main board.(JC92-02636A) |
| Error code: | H1-1251, H1-1252 |
| Description: | Paper Low in tray 2 / Paper is low in tray 2. Load paper Paper Empty in tray 2 / Paper is empty in tray 2. Load paper |
| Causes: | Paper in the tray2 is less than 10% of specification or empty. / The photo sensor is defective. |
| Remedy: | 1) Remove tray2. Load the paper in tray2. 2) If paper is loaded but error message has not disappeared, check the following. a) Check if the paper empty sensor is contaminated. If so, clean it. b) If the paper empty sensor is defective, replace it. c) If the empty actuator is defective, replace it. |
| Error code: | H1-1253 |
| Display: | Input System Failure #H1-1253 : Pull Tray 2 out and insert it. |
| Description: | The paper is not fed from tray2. |
| Causes: | The paper is not fed from tray2. |
| Remedy: | 1) Check if the Gear-Idle Lift is broken. 2) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 3) If the connection is OK, replace the cassette detection sensor(JC34-00001A). 4) Check if the Lift-Motor connector is connected properly. 5) If the problem persists, replace the Lift-Motor(JC81-08705A). |
| Error code: | H1-1311, H1-1313 |
| Description: | Paper jam in Tray 3. Paper jam in tray 3 or tray door is open. |
| Causes: | Paper jam has occurred in tray3. (Pick up unit connection is defective. / Pickup rollers are defective. / Pick up sensor is defective.) |
| Remedy: | 1) Remove the tray3. Remove the jammed paper. And install the tray3. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers. 5) Check the tray 3 pick up unit. • Check if the sensor and actuator are assembled correctly. When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor. • If there is a defective part like a actuator, spring etc., replace it or the tray 3 pick up unit. 6) Check the tray 3 pick up motor. • Check if the tray 3 pick up motor cable is connected correctly. • If the connection is OK, replace the tray 3 pick up drive unit. |
| Error code: | H1-1317, H1-1318, H1-1319 |
| Description: | Paper jam in Tray 3. Paper jam in tray 3 or tray door is open. |
| Causes: | Paper jam has occurred in tray3. (Pick up unit connection is defective. / Pickup rollers are defective. / Pick up sensor is defective.) |
| Remedy: | 1) Remove the tray3. Remove the jammed paper. And install the tray3. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers. 5) Check the tray 3 pick up unit. • Check if the sensor and actuator are assembled correctly. When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor. • If there is a defective part like a actuator, spring etc., replace it or the tray 3 pick up unit. 6) Check the tray 3 pick up motor. • Check if the tray 3 pick up motor cable is connected correctly. • If the connection is OK, replace the tray 3 pick up drive unit. |
| Error code: | H1-1320 |
| Description: | Tray 3 door is open. Close it |
| Causes: | Tray 3 door is open. |
| Remedy: | 1) Check if the tray3 door is closed. If not, close it. 2) If the problem persists, check the door open sensor. If it is defective, replace it. 3) If the sensor is normal, replace the SCF board. |
| Error code: | H1-1322, H1-1340 |
| Description: | Tray 3 cassette is pulled out. Insert it properly. Tray 3 is not installed. Install the tray. |
| Causes: | Tray 3 is pulled out or the cassette detection sensor connector is not connected or broken. |
| Remedy: | 1) Remove and insert tray3 correctly. 2) If the problem persists, remove tray3 again. 3) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the cassette detection sensor. 5) If the problem persists, replace the SCF board. |
| Error code: | H1-1332 |
| Description: | Error: #H1-1332 / Tray Failure: #H1-1332. Check tray 3 connection & turn off then on. Call for service if the problem persists |
| Causes: | Connection between the main machine and the SCF unit is abnormal. |
| Remedy: | 1) Check the harness connection between the main machine and the SCF unit. Reconnect the harness. 2) If the problem persists, replace the SCF board. 3) If the SCF board is normal, replace the Main board. |
| Error code: | H1-1351, H1-1352 |
| Display: | Paper is low in Tray 3. Load paper. Paper is empty in Tray 3. Load paper. |
| Description: | Paper in the tray is less than 10%. / The photo sensor is defective.). |
| Causes: | Paper in the tray3 is less than 10% of specification or empty. / The photo sensor is defective. |
| Remedy: | 1) Remove tray3. Load the paper in the tray3. 2) If paper is loaded but error message has not disappeared, check the following. a) Remove the DCF pick up unit1. b) Check if the photo sensor in the DCF pick up unit1 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. d) If the actuator(JC66-03199A) is defective, replace it. |
| Error code: | H1-1353 |
| Display: | Input System Failure #H1-1353 : Pull Tray 3 out and insert it. |
| Description: | Input System Failure #H1-1353 : Pull Tray 3 out and insert it. |
| Causes: | The paper is not fed from tray3. |
| Remedy: | 1) Remove and insert tray3 correctly. 2) Turn the machine off then on. 3) If the problem persists, turn the machine off. 4) Remove the Bracket Rear Cover after removing 5 screws. 5) Check if the connection between the DCF pick up drive and DCF board is correct. 6) If the connection is OK, replace the pick up drive unit(JC93-00442A). 7) If the problem persists, check the following. a) Remove the DCF pick up unit1. b) Check if the photo sensor in the DCF pick up unit1 is contaminated, clean it. c) If the photo sensor(0604-001393) is defective, replace it. |
| Error code: | H1-1411, H1-1413 |
| Description: | Paper jam in Tray 4. Paper jam in tray 4 or tray door is open. |
| Causes: | Paper jam has occurred in tray4. (Pick up unit connection is defective. / Pickup rollers are defective. / Pick up sensor is defective.) |
| Remedy: | 1) Remove the tray4. Remove the jammed paper. And install the tray4. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers. 5) Check the tray 4 pick up unit. • Check if the sensor and actuator are assembled correctly. When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor. • If there is a defective part like a actuator, spring etc., replace it or the tray 4 pick up unit. 6) Check the tray 4 pick up motor. • Check if the tray 4 pick up motor cable is connected correctly. • If the connection is OK, replace the tray 4 pick up drive unit. |
| Error code: | H1-1417, H1-1418, H1-1419 |
| Description: | Paper jam in Tray 4. Paper jam in tray 4 or tray door is open. |
| Causes: | Paper jam has occurred in tray4. (Pick up unit connection is defective. / Pickup rollers are defective. / Pick up sensor is defective.) |
| Remedy: | 1) Remove the tray4. Remove the jammed paper. And install the tray4. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the tray. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers. 5) Check the tray 4 pick up unit. • Check if the sensor and actuator are assembled correctly. When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor. • If there is a defective part like a actuator, spring etc., replace it or the tray 4 pick up unit. 6) Check the tray 4 pick up motor. • Check if the tray 4 pick up motor cable is connected correctly. • If the connection is OK, replace the tray 4 pick up drive unit. |
| Error code: | H1-1420 |
| Description: | Tray 4 door is open. Close it |
| Causes: | Tray 4 door is open. |
| Remedy: | 1) Check if the tray4 door is closed. If not, close it. 2) If the problem persists, check the door open sensor. If it is defective, replace it. 3) If the sensor is normal, replace the SCF board. |
| Error code: | H1-1422 |
| Display: | Tray 4 cassette is pulled out. Insert it properly. |
| Description: | Tray 4 cassette is pulled out. Insert it properly. |
| Causes: | Tray 4 is pulled out or the auto size sensor connector is not connected or is broken. |
| Remedy: | 1) Remove and insert tray4 correctly. 2) If the problem persists, remove tray3 and tray4. Look inside machine. 3) Check if the auto size sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the auto size sensor(JC93-00018A). 5) If the problem persists, replace the DCF board(JC92-02453A). |
| Error code: | H1-1434 |
| Description: | Error: #H1-1434 / Tray Failure: #H1-1434. Check tray 4 connection & turn off then on. Call for service if the problem persists |
| Causes: | Connection between the main machine and the SCF unit is abnormal. |
| Remedy: | 1) Check the harness connection between the main machine and the SCF unit. Reconnect the harness. 2) If the problem persists, replace the SCF board. 3) If the SCF board is normal, replace the Main board. |
| Error code: | H1-1451, H1-1452 |
| Display: | Paper is low in Tray 4. Load paper. Paper is empty in Tray 4. Load paper. |
| Description: | Paper in tray4 is less than 10%. / The photo sensor is defective. |
| Causes: | Paper in the tray4 is less than 10% of specification. / The photo sensor is defective. |
| Remedy: | 1) Remove the tray4. Load the paper in the tray4. 2) If paper is loaded but error message has not disappeared, check the following. a) Remove the DCF pick up unit2. b) Check if the photo sensor in the DCF pick up unit2 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. d) If the actuator(JC66-03199A) is defective, replace it. |
| Error code: | H1-1453 |
| Display: | Input System Failure #H1-1453 : Pull Tray 4 out and insert it. |
| Description: | Input System Failure #H1-1453 : Pull Tray 4 out and insert it. |
| Causes: | The paper is not fed from tray4. |
| Remedy: | 1) Remove and insert tray4 correctly. 2) Turn the machine off then on. 3) If the problem persists, turn the machine off. 4) Remove the Bracket Rear Cover after removing 5 screws. 5) Check if the connection between the DCF pick up drive and DCF board is correct. 6) If the connection is OK, replace the pick up drive unit(JC93-00442A). 7) If the problem persists, check the following. a) Remove the DCF pick up unit2. b) Check if the photo sensor in the DCF pick up unit2 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. |
| Error code: | H1-2211, H1-2213 |
| Description: | Paper jam in HCF 2. Paper jam in tray 2 or tray door is open. |
| Causes: | Paper jam has occurred in 1st HCF. (Pick up unit connection is defective. / Pickup rollers are defective. / Pick up sensor is defective.) |
| Remedy: | 1) Remove the 1st HCF cassette. Remove the jammed paper. And install the 1st HCF cassette. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the cassette. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers. 5) Check the 1st HCF pick up unit. • Check if the sensor and actuator are assembled correctly. When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor. • If there is a defective part like a actuator, spring etc., replace it or the 1st HCF pick up unit. 6) Check the 1st HCF pick up motor. • Check if the 1st HCF pick up motor cable is connected correctly. • If the connection is OK, replace the 1st HCF pick up drive unit. |
| Error code: | H1-2217, H1-2218, H1-2219 |
| Description: | Paper jam in HCF 2. Paper jam in tray 2 or tray door is open. |
| Causes: | Paper jam has occurred in 1st HCF. (Pick up unit connection is defective. / Pickup rollers are defective. / Pick up sensor is defective.) |
| Remedy: | 1) Remove the 1st HCF cassette. Remove the jammed paper. And install the 1st HCF cassette. 2) If the problem persists, check the followings. 3) Check if the proper paper is loaded in the cassette. If not, replace the paper. 4) Check if the pick up/reverse/forward roller are contaminated or worn out. Replace these rollers. 5) Check the 1st HCF pick up unit. • Check if the sensor and actuator are assembled correctly. When the paper or something puts on sensor, check the sensor output. Check if the value is changed to 3.3V width. If not, replace the sensor. • If there is a defective part like a actuator, spring etc., replace it or the 1st HCF pick up unit. 6) Check the 1st HCF pick up motor. • Check if the 1st HCF pick up motor cable is connected correctly. • If the connection is OK, replace the 1st HCF pick up drive unit. |
| Error code: | H1-2220 |
| Description: | HCF 2 door is open. Close it. |
| Causes: | The right door of the 1st HCF is open. / The door open sensor is defective. |
| Remedy: | 1) Open and close the 1st HCF door. 2) If the problem persists, check the door open sensor. • Check if the door open sensor connector is connected correctly. • If the sensor operation is abnormal, replace it. |
| Error code: | H1-2222, H1-2240 |
| Description: | HCF 2 cassette is pulled out. Insert it properly. HCF 2 is not installed. Install the HCF. |
| Causes: | 1st HCF cassette is pulled out or the cassette detection sensor connector is not connected or broken. |
| Remedy: | 1) Remove and insert the 1st HCF cassette correctly. 2) If the problem persists, remove the 1st HCF cassette again. 3) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the cassette detection sensor. 5) If the problem persists, replace the HCF board. |
| Error code: | H1-2230 |
| Description: | Input System Failure: #H1-2230. Check HCF 2 connection. |
| Causes: | The communication error between the 1st HCF and the main machine has occurred. |
| Remedy: | 1) Check if the HCF unit connector is connected to the machine correctly. Reconnect it. 2) If the drawer connector is deformed, replace it. |
| Error code: | H1-2251, H1-2252 |
| Description: | Paper is low in HCF 2. Load paper. Paper is empty in HCF 2. Load paper. |
| Causes: | Paper in the 1st HCF cassette is less than 10% of specification. / The photo sensor is defective. |
| Remedy: | 1) Remove 1st HCF cassette. Load the paper in the 1st HCF cassette. 2) If paper is loaded but error message has not disappeared, check the following. a) Remove the 1st HCF pick up unit. b) Check if the paper empty sensor is contaminated. If so, clean it. c) If the paper empty sensor is defective, replace it. d) If the empty actuator is defective, replace it. |
| Error code: | H1-2253 |
| Description: | Input System Failure #H1-2253 : Pull HCF 2 out and insert it. |
| Causes: | The paper is not fed from HCF. |
| Remedy: | 1) Turn the machine off than on. 2) If the problem persists, turn the machine off. 3) Check if the connection between the 1st HCF pick up drive and HCF board is correct. 4) If the connection is OK, replace the 1st HCF pick up drive unit. 5) If the problem persists, check the following. a) Remove the 1st HCF pick up unit. b) Check if the pick up sensor is contaminated, clean it. c) If the pick up sensor is defective, replace it. |
| Error code: | H2-5001, H2-5002, H2-5096 |
| Display: | Finisher Failure #. Turn off then on, after checking finisher |
| Description: | Finisher Failure #H2-5001. Turn off then on, after checking finisher Finisher Failure #H2-5002. Turn off then on, after checking finisher Finisher Failure #H2-5096. Turn off then on, after checking finisher |
| Causes: | Main Paddle operation is abnormal. (Paddle home failure / Paddle move failure) |
| Remedy: | 1) Is the Main Paddle overruns during the operation? a) Check if the Paddle home sensor actuator(SJ10 3302) is abnormality. b) Check if the connector(SJ10 8310) of Paddle home sensor (S4) is disconnected. c) Check if the connector(SJ10 8310) J8 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (JR10 8310), replace as is necessary. e) Replace the finisher Paddle home sensor(S4). f) Replace the Finisher main board(JC81–07242A). 2) Is the Paddle Motor (M3) working? a) Check if the connector(JR10 8320) of Paddle motor(M3) is disconnected. b) Check if the connector(JR10 8320) J5 on the finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Paddle motor(M3). e) Replace the Finisher main board(JC81–07242A). 3) Check if the gears(SJ10 3308) of Paddle motor(M3) are assembled correctly. 4) Check if the tooth of gears(SJ10 3308) are broken. If it is defective, replace the broken gears(SJ10 3308). 5) Check if the Paper Path Diverter gears(cam) (JR10 3302) are assembled correctly or operated well. 6) Check if the gears(cam) (JR10 3302) are broken. If it is defective, replace the broken gears(cam). 7) Replace the Paddle Unit(JR10 3130). |
| Error code: | H2-5003, H2-5004, H2-5097 |
| Display: | Finisher Failure #. Turn off then on, after checking finisher |
| Description: | Finisher Failure #H2-5003. Turn off then on, after checking finisher Finisher Failure #H2-5004. Turn off then on, after checking finisher Finisher Failure #H2-5097. Turn off then on, after checking finisher |
| Causes: | Front Jogger operation is abnormal. |
| Remedy: | 1) Is the Front Jogger Home sensor (S6) working? a) Check if the Front Jogger home sensor actuator(SJ10 3318) is abnormality. b) Check if the connector(SJ10 8310) of Front Jogger home sensor(S6) is disconnected. c) Check if the connector(SJ10 8310) J8 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (JR10 8310), replace as is necessary. e) Replace the Front Jogger home sensor(S6). f) Replace the Finisher main board(JC81–07242A). 2) Is the Front Jogger motor (M5) working? a) Check if the connector (SJ10 8310)of Front Jogger motor(M5) is disconnected. b) Check if the connector (SJ10 8310) J6 on the finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8310), replace as is necessary. d) Replace the Front Jogger motor(M5). e) Replace the Finisher main board(JC81–07242A). 3) Is there any belt(gear) jumping noise? a) Check if the Front Jogger driving belt(JC81-03509A) is assembled correctly. b) Check if the Front Jogger driving belt(JC81-03509A) is broken. Replace the belt if it does. c) Check if the Front Jogger motor bracket(SJ10 3206) is fasten on tamper base(JR10 3304) by screw. d) Check if the tooth of gear(SJ10 3308) is broken. Replace the gear if it does. e) Check if the Front Jogger shaft(JR10 3304) became pollution. Remove if it does. 4) Replace the Front Jogger Unit(JC81-03511C). |
| Error code: | H2-5005, H2-5006, H2-5098 |
| Display: | Finisher Failure #. Turn off then on, after checking finisher |
| Description: | Finisher Failure #H2-5005. Turn off then on, after checking finisher Finisher Failure #H2-5006. Turn off then on, after checking finisher Finisher Failure #H2-5098. Turn off then on, after checking finisher |
| Causes: | Rear Jogger operation is abnormal. |
| Remedy: | 1) Is the Rear Jogger Home sensor (S5) working? a) Check if the Rear Jogger home sensor actuator(SJ10 3318) is abnormality. b) Check if the connector(JR10 8320) of Rear Jogger home sensor(S5) is disconnected. c) Check if the connector(JR10 8320) J7 on the finisher main board(JC81–07242A) is disconnected. d) Check discontinuity and damage of the harness(JR10 8320), replace it if required. e) Replace the Rear Jogger home sensor(S5). f) Replace the Finisher main board(JC81–07242A). 2) Is the Rear Jogger motor (M4) working? a) Check if the connector(JR10 8320) of Rear Jogger motor is disconnected. b) Check if the connector(JR10 8320) J5 on the finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Rear Jogger motor(M4). e) Replace the Finisher main board(JC81–07242A). 3) Is there any belt(gear) jumping noise? a) Check if the Rear Jogger driving belt(JC81-03509A) is assembled correctly. b) Check if the Rear Jogger driving belt(JC81-03509A) is broken. Replace the belt if it does. c) Check if the Rear Jogger motor bracket(SJ10 3206) is fasten on tamper base(JR10 3306) by screw. d) Check if any of the teeth on gear (SJ10 3308) are broken. Replace the gear if necessary. e) Check if the Front Jogger shaft (JR10 3304) is contaminated. Clean as is necessary. 4) Replace the Rear Jogger Unit(JC81-03507C). |
| Error code: | H2-5007, H2-5008, H2-5099 |
| Display: | Finisher Failure #. Turn off then on, after checking finisher |
| Description: | Finisher Failure #H2-5007. Turn off then on, after checking finisher Finisher Failure #H2-5008. Turn off then on, after checking finisher Finisher Failure #H2-5099. Turn off then on, after checking finisher |
| Causes: | Extension Tray operation is abnormal. |
| Remedy: | 1) Is the Extension Tray Home sensor (S9) working? a) Check if the Extension Tray home sensor actuator(JC81-03483B) is abnormality. b) Check if the connector(SJ10 8380) of Extension Tray home sensor(S9) is disconnected. c) Check if the connector(SJ10 8310) J8 on the finisher main board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace it if required. e) Replace the Extension Tray home sensor(S9). f) Replace the Finisher main board(JC81–07242A). 2) Is the Extension Tray motor (M6) working? a) Check if the connector (SJ10 8310) of Extension Tray motor is disconnected. b) Check if the connector(SJ10 8310) J6 on the finisher main board(JC81–07242A) is disconnected. c) Check continuity and if the harness is damaged, replace it if required. d) Replace the Extension Tray motor(M6). e) Replace the Finisher main board(JC81–07242A). 3) Check if the gears(SJ10 5342) are assembled correctly. 4) Check if the tooth of gears(SJ10 5342) are broken. Replace the broken gears. 5) Check if the Extension Tray Home sensor bracket(SJ10 5120) is deformed.(make a right angle) Replace the bracket. 6) Replace the Extension Tray Unit(SJ10 5000). |
| Error code: | H2-5009, H2-5010 |
| Display: | Finisher Failure #. Turn off then on, after checking finisher |
| Description: | Finisher Failure #H2-5009. Turn off then on, after checking finisher Finisher Failure #H2-5010. Turn off then on, after checking finisher |
| Causes: | Ejector operation is abnormal. |
| Remedy: | 1) Is the ejector home sensor (S8) working? a) Check if the Ejector home sensor actuator(SJ10 2382) is abnormal. b) Check if the connector(SJ10 8360) of ejector home sensor is disconnected. c) Check if the connector(JR10 8320) J7 on the finisher main board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace it if required. e) Replace the ejector home sensor(S8). f) Replace the Finisher main board(JC81–07242A). 2) Is the ejector moves very fast? a) Check if the Ejector Encoder sensor actuator (SJ10 4362) is abnormal. b) Check if the connector(SJ10 8310) of ejector encoder sensor(S17) is disconnected. c) Check if the connector(SJ10 8310) J13 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (SJ10-8310), replace as is necessary. e) Replace the ejector encoder sensor(S17). f) Replace the Finisher main board(JC81–07242A). 3) Is the ejector motor (M7) working? a) Check if the connector(SJ10 8310) of ejector motor(SJ10 4143) is disconnected. b) Check if the connector(SJ10 8310) J6 on the finisher main board(JC81–07242A) is disconnected. c) Check continuity and if the harness is damaged, replace it if required. d) Replace the ejector motor(M7). e) Replace the Finisher main board(JC81–07242A). 4) Can you hear the sound that the ejector driving belt is jumping during operation? a) Check if the ejector motor bracket(SJ10 4204) assembly is fasten on compiler bottom frame by screw. 5) Check if the tooth of gears(SJ10 4304) are broken. Replace the broken gears. 6) Replace the ejector unit(JC81-03773C). |
| Error code: | H2-5011, H2-5100 |
| Display: | Finisher Failure #. Turn off then on, after checking finisher |
| Description: | Finisher Failure #H2-5011. Turn off then on, after checking finisher Finisher Failure #H2-5100. Turn off then on, after checking finisher |
| Causes: | Ejector operation is abnormal. |
| Remedy: | 1) Is the ejector home sensor (S8) working? a) Check if the Ejector home sensor actuator(SJ10 2382) is abnormal. b) Check if the connector(SJ10 8360) of ejector home sensor is disconnected. c) Check if the connector(JR10 8320) J7 on the finisher main board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace it if required. e) Replace the ejector home sensor(S8). f) Replace the Finisher main board(JC81–07242A). 2) Is the ejector moves very fast? a) Check if the Ejector Encoder sensor actuator (SJ10 4362) is abnormal. b) Check if the connector(SJ10 8310) of ejector encoder sensor(S17) is disconnected. c) Check if the connector(SJ10 8310) J13 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (SJ10-8310), replace as is necessary. e) Replace the ejector encoder sensor(S17). f) Replace the Finisher main board(JC81–07242A). 3) Is the ejector motor (M7) working? a) Check if the connector(SJ10 8310) of ejector motor(SJ10 4143) is disconnected. b) Check if the connector(SJ10 8310) J6 on the finisher main board(JC81–07242A) is disconnected. c) Check continuity and if the harness is damaged, replace it if required. d) Replace the ejector motor(M7). e) Replace the Finisher main board(JC81–07242A). 4) Can you hear the sound that the ejector driving belt is jumping during operation? a) Check if the ejector motor bracket(SJ10 4204) assembly is fasten on compiler bottom frame by screw. 5) Check if the tooth of gears(SJ10 4304) are broken. Replace the broken gears. 6) Replace the ejector unit(JC81-03773C). |
| Error code: | H2-5012, H2-5013, H2-5101 |
| Display: | Finisher Failure #. Turn off then on, after checking finisher |
| Description: | Finisher Failure #H2-5012. Turn off then on, after checking finisher Finisher Failure #H2-5013. Turn off then on, after checking finisher Finisher Failure #H2-5101. Turn off then on, after checking finisher |
| Causes: | Stapler head clinching motor is not working properly. |
| Remedy: | 1) Is the Head of Stapler(JC81-03475B) opened? a) Replace stapler cartridge(JC81-03481A). b) Check if the connectors(SJ10 8310) of stapler head are disconnected. c) Check if the connector(SJ10 8310) P7 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (SJ10-8310), replace as is necessary. e) Replace the stapler unit(SJ10 3140). f) Replace the Finisher main board(JC81–07242A). 2) Replace the stapler unit(SJ10 3140). |
| Error code: | H2-5014, H2-5015, H2-5102 |
| Display: | Finisher Failure #. Turn off then on, after checking finisher |
| Description: | Finisher Failure #H2-5014. Turn off then on, after checking finisher Finisher Failure #H2-5015. Turn off then on, after checking finisher Finisher Failure #H2-5102. Turn off then on, after checking finisher |
| Causes: | Stacker operation is abnormal. |
| Remedy: | 1) Are the Stacker Upper Limit(Top) Sensors (S10) working? a) Check if the sensor actuator(SJ10 6332A) is abnormality. b) Check if the connector(SJ10 8370) of the sensors are disconnected. c) Check if the connector(SJ10 8310) J8 on the finisher main board(JC81–07242A) is disconnected. d) Check discontinuity and damage of the harness(SJ10 8310, SJ10 8370), replace it if required. e) Replace the stacker upper limit sensors(S10). f) Replace the Finisher main board(JC81–07242A). 2) Is the Stacker Full Sensor (S16) working? a) Check if the sensor actuator(JR10 6210) is abnormality. b) Check if the connector(JR10 8320) of stacker full sensor is disconnected. c) Check if the connector(JR10 8320) J18 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (SJ10 8320), replace as is necessary. e) Replace the stacker encoder sensor(S16). f) Replace the Finisher main board(JC81–07242A). 3) Is the stacker Lower Limit Switch (SW2) working? a) Check if the sensor actuator(JR10 6310) is abnormality. b) Check if the connector(JR10 8360) of stacker Lower switch is disconnected. c) Check if the connector(JR10 8360) J14 on the finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (JR10 8360), replace as is necessary. e) Replace the stacker bottom limit sensor(SW2). f) Replace the Finisher main board(JC81–07242A). 4) Is the stacker motor (M8) working? a) Check if the connector(JR10 8360) of stacker motor is disconnected. b) Check if the connector(JR10 8360) J14 on the finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8360), replace as is necessary. d) Replace the stacker motor(M8). e) Replace the Finisher main board(JC81–07242A). 5) Replace the stacker motor gear box(SJ10 6110). |
| Error code: | H2-5032 |
| Display: | Paper jam in front of finisher: #H2-5032 |
| Description: | Paper jam in front of finisher: #H2-5032 |
| Causes: | Sheet not leaving finisher paper path section. |
| Remedy: | Check if there is any paper on the finisher, the IOT paper path. Remove it if there is. If the error still occurs, check the followings. 1) Check if the Finisher of the interface cable(JC81-03470A) should be connected with the IOT. a) Power of the IOT Off. b) IOT and Finisher of the interface cable(JC81-03470A) is connected. c) Power of the IOT On. 2) Is the LEDs of the Main Control Board (JC81–07242A) working? <Open the Bottom cover (SJ10 6160) of Finisher > a) The Finisher Guides (JC63-03941A, JC81-07249B) need to be placed in the UP Position, so the Front Door can be closed properly. b) Red, yellow color LED is ON, and Green LED flickers c) Replace the Finisher main control board(JC81–07242A). 3) Is the Finisher Entrance Sensor(S2) working? a) Check if the Entrance sensor actuator(SJ10 2384) is abnormality. b) Check if the connector (SJ10 8350)of Finisher entrance sensor(S2) is disconnected. c) Check if the connector(JR10 8320) J7 on the Finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (SJ10 8350, SJ10 8320), as is necessary. e) Replace the Finisher input sensor(S2). f) Replace the Finisher main control board(JC81–07242A). 4) Is the Feed Entrance Motor (M1) working? a) Check if the connector(JR10 8320) of the Feed entrance motor is disconnected. b) Check if the connector(JR10 8320) J5 on the Finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Feed entrance motor(M1). e) Replace the Finisher main control board(JC81–07242A). 5) Check if there is any object on finisher paper path. Remove it if there is. |
| Error code: | H2-5033, H2-5035, H2-5036 |
| Display: | Paper jam inside of finisher: # |
| Description: | Paper jam inside of finisher: #H2-5033 Paper jam inside of finisher: #H2-5035 Paper jam inside of finisher: #H2-5036 |
| Causes: | Sheet jam on finisher paper path section |
| Remedy: | Check if there is any paper on the finisher, the IOT paper path. Remove it if there is. If the error still occurs, check the followings. 1) Is the Finisher Entrance Sensor(S2) working? a) Check if the Entrance sensor actuator(SJ10 2384) is abnormality. b) Check if the connector(SJ10 8350) of Finisher entrance sensor(S2) is disconnected. c) Check if the connector(JR10 8320) J7 on the Finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (JR10 8320, SJ10 8350), replace as is necessary. e) Replace the Finisher entrance sensor(S2). f) Replace the Finisher main control board(JC81–07242A). 2) Is the Feed Entrance Motor (M1) working? a) Check if the connector(JR10 8320) of the Feed entrance motor is disconnected. b) Check if the connector(JR10 8320) J5 on the Finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Feed entrance motor(M1). e) Replace the Finisher main control board(JC81–07242A). 3) Is the Finisher Exit Sensor (S3,S11) working? a) Check if the Exit sensor actuator (SJ10 2384) is abnormality. b) Check if the connector(SJ10 8340) of the Finisher Exit sensor(S3) is disconnected. c) Check if the connector(JR10 8320) J7 on the Finisher main board(JC81–07242A) is disconnected. d) Check if there is continuity in the harness, and if not replace the harness (JR10 8320, SJ10 8340), replace as is necessary. e) Replace the Finisher exit sensor(S3,S11). f) Replace the Finisher main control board(JC81–07242A). 4) Is the Feed Exit Motor(M2) working? a) Check if the connector(JR10 8320) of the Feed exit motor is disconnected. b) Check if the connector J5 on the finisher main board(JC81–07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Feed exit motor(M2). e) Replace the Finisher main control board(JC81–07242A). 5) Check if there is any object on finisher paper path. Remove it if there is. |
| Error code: | H2-5034, H2-5037 |
| Display: | Finisher Failure #H2-5003. Turn off then on, after checking finisher |
| Description: | Finisher Failure #H2-5003. Turn off then on, after checking finisher |
| Causes: | Sheet jam on finisher exit section |
| Remedy: | Check if there is any paper on the finisher, the IOT paper path. Remove it if there is. If the error still occurs, check the followings. 1) Is the Finisher Exit Sensor(S3, S11) working? a) Check if the Exit sensor actuator (SJ10 2384)is abnormality. b) Check if the connector(SJ10 8340) of the Finisher Exit sensor(S3) is disconnected. c) Check if the connector(JR10 8320) J7 on the Finisher main board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged , replace as is necessary. e) Replace the Finisher exit sensor(S3,S11). f) Replace the Finisher main control board(JC81–07242A). 2) Is the Feed Exit Motor(M2) working? a) Check if the connector(JR10 8320) of the Feed exit motor is disconnected. b) Check if the connector J5 on the finisher main board(JC81 07242A) is disconnected. c) Check if there is continuity in the harness, and if not replace the harness (JR10 8320), replace as is necessary. d) Replace the Feed exit motor(M2). e) Replace the Finisher main control board(JC81 07242A). 3) Check if there is any object on finisher paper path. Remove it if there is. |
| Error code: | H2-5048 |
| Display: | Finisher door is open. Close it |
| Description: | Finisher door is open. Close it |
| Causes: | Finisher Door is Opened. Power(24V) supply is cut off, and then stop the operation of Finisher. |
| Remedy: | Check if the all door of finisher closed. If the error still occurs, check the followings. 1) Is the all Doors of Finisher closed? a) Close the doors(JC63-03941A) opened. 2) Is the Front Door (JC63-03941A) Switch (SW1) working? a) Check if the Switch(SW1) and the Actuator(JC63-03941A) is abnormality. b) Check if the connector(JR10 8360) of Switch is disconnected. c) Check if the connector(JR10 8360) J2 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace the Door switch(SW1). f) Replace the Finisher main control board(JC81–07242A). |
| Error code: | H2-506x, H2-507x, H2-5A50 |
| Display: | Finisher Failure #H2-506x. Turn off then on, after checking finisher Finisher Failure #H2-507x. Turn off then on, after checking finisher Finisher Failure #H2-5A50. Check finisher |
| Description: | Finisher Failure #H2-506x. Turn off then on, after checking finisher Finisher Failure #H2-507x. Turn off then on, after checking finisher Finisher Failure #H2-5A50. Check finisher |
| Causes: | Communication error between the IOT and the Finisher. |
| Remedy: | If the error still occurs, check the followings. 1) Check if the Finisher of the interface cable(JC81-03470A) should be connected with the IOT. a) Power Switch of the IOT Off. b) IOT and Finisher of the interface cable(JC81-03470A) is connected. c) Power Switch of the IOT On. 2) Is the LEDs of the Main Control Board (JC81–07242A) working? < Open the Bottom cover(SJ10 6160) of Finisher > a) The Finisher of the Doors(JC63-03941A, JC81-07249B) should remain closed to all. b) Red, yellow color LED is ON, and Green LED flickers. c) Replace the Finisher main control board(JC81–07242A). 3) Check the Interface Cable(JC81-03470A) of Main Control Board(JC81–07242A). a) Check if the connector(JC81–07242A) J1,J3 on the main control board (JC81–07242A) is disconnected. b) Check continuity and if the harness is damaged(JC81-03470A), replace as is necessary. c) Replace the Finisher main control board(JC81–07242A). 4) Replace the Finisher main control board(JC81–07242A). |
| Error code: | H2-5080 ... H2-5085 |
| Description: | Paper Jam in front of mailbox. Remove paper: #H2-508x Paper Jam inside of mailbox. Remove paper: #H2-508x Paper Jam at mailbox bin 1. Remove paper: #H2-508x |
| Causes: | Jam in mailbox has occurred. |
| Remedy: | Check if there is any paper on the mail box. Remove it if there is. If the error still occurs, check the followings. 1) Check if the photo sensor connector is connected correctly. Reconnect it. 2) Check the sensor connection on mailbox main board. Reconnect it. 3) Check if the feed actuator is assembled correctly. If it is deformed or broken, replace it. 4) Check the feed and separation(diverter) motor. If there is any defective motor, replace it. |
| Error code: | H2-5086, H2-5087 |
| Description: | Mainbox Failure: #H2-5xxx. Check mailbox |
| Causes: | Diverter motor is defective. |
| Remedy: | 1) Remove the mailbox rear cover. 2) Check the connection between diverter motor and mailbox main board. Reconnect the harness. 3) If the connection is OK, replace the diverter motor. 4) If the problem persists, replace the mailbox main board. |
| Error code: | H2-5088 |
| Description: | Mailbox door is open. Close it |
| Causes: | Mailbox door is opened. |
| Remedy: | 1) Open and close the mailbox door. 2) Check the connection between door open sensor and mailbox main board. Reconnect the harness. 3) If the harness is defective, replace it. 4) If the connection is OK, replace the door open sensor. |
| Error code: | H2-5112, H2-5113 |
| Description: | Mainbox Failure: #H2-5xxx. Check mailbox |
| Causes: | Diverter motor is defective. |
| Remedy: | 1) Remove the mailbox rear cover. 2) Check the connection between diverter motor and mailbox main board. Reconnect the harness. 3) If the connection is OK, replace the diverter motor. 4) If the problem persists, replace the mailbox main board. |
| Error code: | H2-5A21 |
| Display: | Finisher Top door is open. Close it |
| Description: | Finisher Top door is open. Close it |
| Causes: | Finisher Top Door is Opened. |
| Remedy: | Check if the all door of finisher closed. If the error still occurs, check the followings. 1) Are all Paper Guides in there up position; and is the Front Door of Finisher closed? a) Close the Top Door(JC81-07249B) opened. 2) Is the Top Door Sensor (S16) working? a) Check if the top door sensor actuator(JC81-07249B) is abnormality. b) Check if the connector(JR10 8330) of sensor is disconnected. c) Check if the connector(JR10 8330) J1,J2 on the main control board (JC81–07242A)is disconnected. d) Check continuity and if the harness is damaged , replace as is necessary. e) Replace the Finisher top Door sensor(S16). f) Replace the Finisher main control board(JC81–07242A). 3) Replace the Finisher main control board(JC81–07242A). |
| Error code: | H2-5A31, H2-5A32 |
| Display: | The paper in finisher stacker is nearly full. Remove printed paper The paper in finisher stacker is full. Remove printed paper The paper in finisher bin2 is nearly full. Remove printed paper The paper in finisher bin2 is nearly full. Remove printed paper |
| Description: | The paper in finisher stacker is nearly full. Remove printed paper The paper in finisher stacker is full. Remove printed paper |
| Causes: | Finisher stacker tray made full, or Stacker operation is abnormal. |
| Remedy: | Check if there is any paper on the Finisher Stacker Tray. Remove it if there is. If the error still occurs, check the followings. 1) Is the Finisher Stack Height Sensor (S10) working? a) Check if the Stack height sensor actuator(SJ10 6332A) is abnormality. b) Check if the connector (SJ10 8370)of Stack height sensor(S10) is disconnected. c) Check if the connector(SJ10 8310) J8 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace the finisher Stack height sensor(S10). f) Replace the Finisher main control board(JC81–07242A). 2) Is the Finisher Stack Full Sensor (S17) working? a) Check if the Stack full sensor actuator(SJ10 6332A) is abnormality. b) Check if the connector of Stack full sensor is disconnected. c) Check if the connector(JR10 8320) J18 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace the finisher stack full sensor(S10). f) Replace the Finisher main control board(JC81–07242A). 3) Is the Stacker Motor (M8) working? a) Check if the connector(SJ10 8360) of stacker motor is disconnected. b) Check if the connector(SJ10 8360) J14 on the finisher main board(JC81–07242A) is disconnected. c) Check continuity and if the harness is damaged, replace as is necessary. d) Replace the stack motor(M8). 4) Replace the Finisher main control board(JC81–07242A). |
| Error code: | H2-5A34, H2-5A35 |
| Display: | The paper in finisher stacker is nearly full. Remove printed paper The paper in finisher stacker is full. Remove printed paper The paper in finisher bin2 is nearly full. Remove printed paper The paper in finisher bin2 is nearly full. Remove printed paper |
| Description: | The paper in finisher bin2 is nearly full. Remove printed paper The paper in finisher bin2 is nearly full. Remove printed paper |
| Causes: | Finisher stacker tray made full, or Stacker operation is abnormal. |
| Remedy: | Check if there is any paper on the Finisher Stacker Tray. Remove it if there is. If the error still occurs, check the followings. 1) Is the Finisher Stack Height Sensor (S10) working? a) Check if the Stack height sensor actuator(SJ10 6332A) is abnormality. b) Check if the connector (SJ10 8370)of Stack height sensor(S10) is disconnected. c) Check if the connector(SJ10 8310) J8 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace the finisher Stack height sensor(S10). f) Replace the Finisher main control board(JC81–07242A). 2) Is the Finisher Stack Full Sensor (S17) working? a) Check if the Stack full sensor actuator(SJ10 6332A) is abnormality. b) Check if the connector of Stack full sensor is disconnected. c) Check if the connector(JR10 8320) J18 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace the finisher stack full sensor(S10). f) Replace the Finisher main control board(JC81–07242A). 3) Is the Stacker Motor (M8) working? a) Check if the connector(SJ10 8360) of stacker motor is disconnected. b) Check if the connector(SJ10 8360) J14 on the finisher main board(JC81–07242A) is disconnected. c) Check continuity and if the harness is damaged, replace as is necessary. d) Replace the stack motor(M8). 4) Replace the Finisher main control board(JC81–07242A). |
| Error code: | H2-5A38 ... H2-5A49 |
| Description: | Paper in mailbox bin X is full. Remove printed paper |
| Causes: | Mailbox outbin is full. |
| Remedy: | 1) Remove the paper on outbin tray. 2) If there is no paper on outbin tray but error persists, check the following. a) Check the connection between outbin full sensor and mailbox main board. Reconnect the harness. b) If the connection is OK, replace the outbin full sensor. c) Check if the outbin actuator is assembled correctly. If it is deformed or broken, replace it. |
| Error code: | H2-5A50, H2-6A50 |
| Description: | Finisher Failure #H2-5A50. Check finisher |
| Causes: | Communication error between finisher and copier. |
| Remedy: | 1) Check the connection between finisher and copier. Reconnect the cable. 2) If the connection is OK, replace the finisher board. |
| Error code: | H2-5A62, H2-5A63 |
| Display: | Staple cartridge is low. Replace it Staple cartridge is empty or not installed. Replace it |
| Description: | Staple cartridge is low. Replace it Staple cartridge is empty or not installed. Replace it |
| Causes: | Can not detected Staple cartridge . |
| Remedy: | Check if there is Staple Cartridge. If the error still occurs, check the followings 1) Is the Staple Cartridge mounted? a) Replace stapler cartridge(JC81-03481A). b) Check if the connector (SJ10 8310)of Staple is disconnected. c) Check if the connector(SJ10 8310) J9,J10 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace staple unit(SJ10 3140). f) Replace the Finisher main control board(JC81–07242A). 2) Mount the stapler cartridge(JC81-03481A). 3) Replace the stapler Unit(SJ10 3140) |
| Error code: | H2-5A90 |
| Display: | Paper jam at the top of finisher: #H2-5A90 |
| Description: | Paper jam at the top of finisher: #H2-5A90 |
| Causes: | Sheet jam on finisher top exit section |
| Remedy: | Check if there is any paper on the finisher, the IOT paper path. Remove it if there is. If the error still occurs, check the followings. 1) Is the Top Exit/Top Empty Sensor(S13, S11) working? a) Check if the Sensor actuator (SJMB2312, SJMB2310) abnormality. b) Check if the connector(JR10 8340) of the Top exit/Top empty sensor(S13, S12) is disconnected. c) Check if the connector(JR10 8330J7 on the Finisher main board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged , replace as is necessary. e) Replace the Top exit/Top Empty sensor(S13,S12). f) Replace the Finisher main control board(JC81–07242A). 2) Is the Paddle Unit(Paper path diverter) working? a) Refer to the troubleshooting for “H2–5001” error. 3) Check if there is any object on finisher paper path. Remove it if there is. |
| Error code: | H2-6A62, H2-6A63 |
| Description: | Staple cartridge is low. Replace it Staple cartridge is empty or not installed. Replace it |
| Causes: | Can not detected Staple cartridge . |
| Remedy: | Check if there is Staple Cartridge. If the error still occurs, check the followings 1) Is the Staple Cartridge mounted? a) Replace stapler cartridge(JC81-03481A). b) Check if the connector (SJ10 8310)of Staple is disconnected. c) Check if the connector(SJ10 8310) J9,J10 on the main control board(JC81–07242A) is disconnected. d) Check continuity and if the harness is damaged, replace as is necessary. e) Replace staple unit(SJ10 3140). f) Replace the Finisher main control board(JC81–07242A). 2) Mount the stapler cartridge(JC81-03481A). 3) Replace the stapler Unit(SJ10 3140) |
| Error code: | M1-1113 |
| Display: | SMART PANEL:Paper jam in tray 1. |
| Description: | Paper jam in Tray 1. |
| Causes: | Paper jam has occurred in tray1. |
| Remedy: | 1) Open the side cover and check if a foreign substance or paper is jammed inside the machine. 2) Remove tray1 and remove the jammed paper. 3) If this jam error occurs frequently, check the rollers of the pick up unit1. a) Remove tray1 and tray2. b) Check if the pick up/ reverse/ forward rollers are assembled correctly. c) If the pick up/ reverse/ forward rollers are worn out or contaminated, replace the defective roller. 4) If the problem persists, check the pick-up unit1. a) Check if the pre-feed sensor is connected correctly. If the sensor is defective, replace it. b) If there is any defective part in pick-up unit 1, replace it or pick up unit 1. 5) If the problem persists, replace the pickup drive unit 1. |
| Error code: | M1-1613 |
| Description: | Paper jam in MP Tray. |
| Causes: | Paper jam has occurred in MP tray. |
| Remedy: | 1) Open the side cover. 2) Remove the jammed paper. 3) If the problem persists, check the followings. 4) Check if the proper paper is loaded in the tray. If not, replace the paper. 5) Check if the MP pick up/reverse roller or MP friction pad is contaminated or worn out. Replace the defective part. 6) Check that the feed sensor actuator moves freely and is not damaged. If necessary, install a new feed sensor actuator assembly. 7) Check the connection between the feed sensor and on the main board. If necessary, install a new feed sensor. 8) Check if the pick up motor runs normally. If necessary, replace the pick up motor. 9) Check the MP clutch. If necessary, replace the MP clutch. |
| Error code: | M1-3122 |
| Display: | Tray 1 cassette is pulled out. Insert it properly. |
| Description: | Tray 1 cassette is pulled out. Insert it properly. |
| Causes: | Tray 1 is pulled out or the auto size sensor connector is not connected or broken. |
| Remedy: | 1) Remove and insert Tray1 correctly. 2) If Tray1 is not locked or pulled out without holding the locking lever, remove Tray1. 3) Check if foreign substance or paper is inside the space between Tray1,2. If so, please remove it. 4) If the problem persists, check that the auto size sensor is connected properly. 5) If the problem persists, replace the main board(JC92–02452A). |
| Error code: | M1-4111 |
| Display: | Input System Failure #M1-4111 : Pull Tray 1 out and insert it. |
| Description: | Input System Failure #M1–4111 : Pull Tray 1 out and insert it. |
| Causes: | The paper is not fed from tray1. |
| Remedy: | 1) Remove tray1 and re-install it. 2) If the problem persists, turn the machine off then on. 3) Enter SVC mode. Execute pickup motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100-0370) 4) If the pick up motor operation is abnormal, turn the machine off. 5) Remove the rear cover. 6) Check if the connection between pickup drive unit1 and main board is secure. 7) If the connection is OK, replace the pickup drive unit(JC93-00442A). 8) If the problem persists, check the pickup unit1. a) Check if the photo sensor in the pickup unit1 is defective. b) If the sensor(0604–001393) is defective, replace it. |
| Error code: | M1-5111, M1-5112, M1-5120 |
| Description: | Paper is low in tray 1. Load paper Paper is empty in tray 1. Load paper Paper is empty in all tray. Load paper |
| Causes: | Tray 1 is nearly empty. / Tray 1 is empty. |
| Remedy: | 1) Remove the tray1. 2) Check if paper is loaded. If it is empty, load the paper. 3) Check the connection between the empty sensor and on the main board. If necessary, install a new empty sensor. 4) Check that the empty sensor actuator moves freely and is not damaged. If necessary, install a new empty sensor actuator assembly. 5) Check the connection between the tray1 lift motor and on the main board. 6) Check the tray1 lift motor operation. If necessary, replace the motor. 7) If necessary, replace the main board. |
| Error code: | M1-5612 |
| Display: | Paper is empty in MP Tray. Load paper. |
| Description: | Paper is empty in MP Tray. Load paper. |
| Causes: | Paper in the MP tray is less than 10%. / The photo sensor is defective. |
| Remedy: | 1) Load the paper in the MP tray. 2) If paper is loaded but error message has not disappeared, check the following : a) If the photo sensor is contaminated, clean it. b) If the photo sensor is defective, replace it(0604–001393). c) If the actuator is defective, replace it(JC66-03217A). |
| Error code: | M2-1111, M2-1114 |
| Description: | Paper jam inside of machine. Please remove the paper |
| Causes: | A paper jam was detected at the feed sensor. |
| Remedy: | 1) Remove the jammed paper. If the error persists, check the followings. 2) Check if there is any obstacles or contamination in the paper path. If yes, clean or remove it. 3) Check if the feed sensor harness is connected properly. Reconnect the harness. 4) If the feed sensor is defective, replace it. 5) Check if the feed roller is contaminated or worn out. If yes, replace it. 6) Check the main drive unit operation. If necessary, replace the main drive unit. |
| Error code: | M2-1117, M2-2111 |
| Description: | Paper jam at the bottom of duplex path Paper jam at the top of duplex path |
| Causes: | Paper jam has occurred at feed sensor. |
| Remedy: | 1) Turn the machine off then on. 2) Open the side cover. Remove the jammed paper. 3) If the problem persists, check the followings. 4) Check that the duplex jam sensor actuator moves freely and is not damaged. If necessary, install a new duplex jam sensor actuator assembly. 5) Check the connection between the duplex jam sensor and on the main board. If necessary, install a new duplex jam sensor. 6) Check if the pick up motor runs normally. If necessary, replace the pick up motor. 7) Check the duplex motor. If necessary, replace the duplex motor. 8) Check the duplex clutch. If necessary, replace the duplex clutch. |
| Error code: | M2-2112, M2-2114 |
| Description: | Paper jam at the bottom of duplex path Paper jam at the top of duplex path |
| Causes: | Paper jam has occurred at feed sensor. |
| Remedy: | 1) Turn the machine off then on. 2) Open the side cover. Remove the jammed paper. 3) If the problem persists, check the followings. 4) Check that the duplex jam sensor actuator moves freely and is not damaged. If necessary, install a new duplex jam sensor actuator assembly. 5) Check the connection between the duplex jam sensor and on the main board. If necessary, install a new duplex jam sensor. 6) Check if the pick up motor runs normally. If necessary, replace the pick up motor. 7) Check the duplex motor. If necessary, replace the duplex motor. 8) Check the duplex clutch. If necessary, replace the duplex clutch. |
| Error code: | M2-2311, M2-2312, M2-2314 |
| Description: | Paper jam at the bottom of duplex path Paper jam at the top of duplex path |
| Causes: | Paper jam has occurred at feed sensor. |
| Remedy: | 1) Turn the machine off then on. 2) Open the side cover. Remove the jammed paper. 3) If the problem persists, check the followings. 4) Check that the duplex jam sensor actuator moves freely and is not damaged. If necessary, install a new duplex jam sensor actuator assembly. 5) Check the connection between the duplex jam sensor and on the main board. If necessary, install a new duplex jam sensor. 6) Check if the pick up motor runs normally. If necessary, replace the pick up motor. 7) Check the duplex motor. If necessary, replace the duplex motor. 8) Check the duplex clutch. If necessary, replace the duplex clutch. |
| Error code: | M3-1111, M3-1112, M3-1114 |
| Description: | Paper jam in exit area. Paper jam inside of machine |
| Causes: | Paper jam has occurred around the fuser unit. |
| Remedy: | 1) Open the side cover. Remove the jammed paper. 2) If this jam occurs continually, check the following. a) Check the connection between the fuser motor and on the main board. b) Check the fuser/exit motor. If the operation is abnormal, replace the motor. c) Remove the fuser unit. Check if fuser unit has any defective part. Replace the fuser unit d) Remove the exit unit. Check if the exit sensor is assembled correctly. If it is defective, replace it. |
| Error code: | M3-2130 |
| Display: | Output bin full Remove paper |
| Description: | Paper in output bin is full. Remove printed paper |
| Causes: | The machine detected that the output tray has got full or the bin-full sensor is defective. |
| Remedy: | 1) Remove the paper on the output tray. (The maximum loading capacity is 150 sheets based on standard paper (80 g/m²).) 2) Check if the Bin-full Sensor connector is connected properly. Reconnect it or replace the Bin-full sensor. |
| Error code: | S1-1313 |
| Display: | The clock became initial time. Set a time again. |
| Description: | The clock became initial time. Set a time again. |
| Causes: | Saved time is invalid |
| Remedy: | 1) Set up the time and reboot the machine. a) Select “Machine Setup” on touch screen. b) Select “General Setting”. c) Select “Date and Time” and set the time. 2) If the problem persists, check the following. a) Remove the rear cover. b) Remove the fax holder from the main board. c) Measure the voltage of the battery. If the battery is normal, the measured value is over 3V. 3) If the battery is normal, replace the main board(JC92-02742A). |
| Error code: | S1-2411 |
| Display: | Error #S1-2411 Turn off then on. |
| Description: | A communication error failure has occurred at HDD of main controller. |
| Causes: | Hard Disk is not installed in the machine. / Hard Disk is defective. |
| Remedy: | 1. Format the hard disk. 2. If the problem persists, replace the hard disk. |
| Error code: | S1-2433, S1-244x |
| Description: | System Failure: #S1-2433 Call for service HDD System Failure #S1-244x : Call for service |
| Causes: | System memory is corrupted. / Unexpected S/W error has occurred. |
| Remedy: | 1) Enter the SVC(tech) mode. Select “System Recovery” in Service Function menu. 2) Execute the hard disk format and firmware re-installation. 3) If the problem persists, replace the HDD. |
| Error code: | S1-2434, S1-2435, S1-2436 |
| Description: | HDD Error #S1-2434. Check users guide. HDD Error #S1-2435. Check users guide. HDD Error #S1-2436. Check users guide. |
| Causes: | HDD partition or memory is full. • S1-2434 : Addresses in Address book / User data in User profile • S1-2435 : Documents in Document box / Jobs in Secure job list / Fonts / Forms • S1-2436 : System Logs • S1-2437/3438/3439 : Printing Error / No Paper in Tray |
| Remedy: | 1) Enter SVC mode. Select “Hard Disk Maintenance” in Service Function menu. 2) Execute hard disk format. 3) If the problem persists, replace the HDD(JC59–00035A). |
| Error code: | S1-2437, S1-2438, S1-2439 |
| Description: | HDD Error #S1-2437. Check users guide. HDD Error #S1-2438. Check users guide. HDD Error #S1-2439. Check users guide. |
| Causes: | HDD partition or memory is full. • S1-2434 : Addresses in Address book / User data in User profile • S1-2435 : Documents in Document box / Jobs in Secure job list / Fonts / Forms • S1-2436 : System Logs • S1-2437/3438/3439 : Printing Error / No Paper in Tray |
| Remedy: | 1) Enter SVC mode. Select “Hard Disk Maintenance” in Service Function menu. 2) Execute hard disk format. 3) If the problem persists, replace the HDD(JC59–00035A). |
| Error code: | S1-2510, S1-2521 |
| Description: | MSOK System Failure #S1-2510: Turn off then on. MSOK Failure: #S1-2521. Call for service |
| Causes: | MSOK is not installed properly. / MSOK is defective. |
| Remedy: | 1) Remove the rear cover. 2) Check if the MSOK is inserted correctly. Remove and reinstall it. 3) If the problem persists, replace the main board. |
| Error code: | S1-2523, S1-2530 |
| Description: | PPM data is incorrect. Call for service & change MSOK Engine System Failure: #S2-1211. Turn off then on |
| Causes: | MSOK is defective. / MSOK data is wrong. |
| Remedy: | 1) Turn the machine off and on. 2) If the problem persists, turn the machine off again. 3) Remove the rear cover. 4) Check if the MSOK is inserted correctly. Remove and reinstall it. 5) If the problem persists, contact the tech support team. |
| Error code: | S2-1211 |
| Display: | Engine System Failure #S2-1211: Turn off then on. |
| Description: | Power chip on main board is defective. |
| Causes: | Communication error between the ASIC on main board and microcontroller IC has occurred. |
| Remedy: | 1) Turn the machine off then on. 2) If the problem persists, replace the main board. |
| Error code: | S2-331D |
| Display: | S2-331D, Waiting for low temp / Waiting delay time for lower fixing temperature… |
| Description: | Wait delay time for lower fixing temperature… |
| Causes: | These errors show the engine status. |
| Remedy: | 1) Please wait until this error will disappear. |
| Error code: | S2-3321 |
| Display: | S2-3321, Supplying Toner / Supplying and mixing toner to developer unit. Please wait… |
| Description: | Supplying and mixing toner to developer unit. Please wait... |
| Causes: | Toner supply is insufficient. |
| Remedy: | 1) Machine will execute the toner supply job. Please wait until error message will be disappeared. 2) If the problem persists, check the toner supply drive unit. 3) If the problem persists, replace the toner cartridge. |
| Error code: | S2-3421 |
| Display: | S2-3421, Calibrating density / Calibrating image density. Please wait… |
| Description: | Calibrating image density. Please wait... |
| Causes: | Machine is on TC calibration. |
| Remedy: | 1) Machine will execute the toner calibration job. Please wait until error message will be disappeared. |
| Error code: | S2-4120 |
| Display: | Door open. Close it. |
| Description: | Door open Close it |
| Causes: | Door is open or the cover open switch is defective. |
| Remedy: | 1) Check if the front cover is closed perfectly. 2) If the error persists, check that the cover-open sensor is working normally. If it is defective, replace the HVPS board. |
| Error code: | S3-3121 |
| Display: | Scanner Locked |
| Description: | CIS unit in the scanner does not move. |
| Causes: | Scanner lock error has occurred. CIS does not move. |
| Remedy: | 1) Check if the CIS unit moves when turning the machine off then on. 2) Check if the CIS cable is connected correctly. Reconnect it. 3) If the CIS unit is defective, replace it. 4) Check if there is any defective part in the scanner. Find and replace it. 5) If the problem persists, replace the main board. |
| Error code: | S3-3211 |
| Display: | Scan System Failure #S3-3211: Turn off then on. |
| Description: | Scan System Failure #S3-3211: Turn off then on. |
| Causes: | ADF is not connected or communication error occurs with CIP6 board. |
| Remedy: | 1) Turn the machine off then on. If the problem persists, check the following: 2) Turn the machine off again. 3) Remove the scan rear cover. Check if the connector on scan joint board is connected correctly. 4) Remove the ADF rear cover. Check if the connector on ADF board is connected correctly. 5) If the connection is OK, replace the ADF board. |
| Error code: | S5-3111 |
| Display: | UI System Failure #S5-3111:Turn off then on. |
| Description: | UI System Failure #S5-3111:Turn off then on. |
| Causes: | Main board has critical problem which make its lockup or USB connection between main board and OPE has some problem. |
| Remedy: | 1) Turn off and turn on. And check if the problem disappears. a) If yes, go to step 2)-a). b) If no, go to step 2)-b). 2) Check the following procedure. a) Print the Error Information Report. . Service Mode - General - Print Reports - Error Information . Check the error code which is printed on the report. - If S5-3111 has occurred, go to step 4). - If S5-3112 has occurred, go to step 5)-c). - If S5-3113 has occurred, go to step 5)-d). b) Enter into System Recovery Mode. . How to enter System Recovery Mode : Turn on the machine with side cover open and power button on OPE is pressed state. . Check if entering System Recovery Mode is possible or not. - If entering System Recovery Mode is successful, go to step 3). - If entering System Recovery Mode fails, go to step 5)-d). 3) Execute the System Recovery. • Insert USB memory stick which has recovery one rom and execute recovery(HDD format). • Check if the problem disappears after system recovery(format complete). - If yes, go to step 4). - If no, go to step 5)-c). 4) Execute the firmware update. • Check if the problem disappears after one rom update. - If the problem disappears, go to step 5)-a). - If the problem happens sometimes, go to step 5)-b). 5) Check the following procedure. a) No more action is required because machine is recovered from S5-3111 error state. Please monitor the machine if S5-3111 happens again. b) Detailed analysis is required. Please capture the log and send it to development team in HQ. c) It seems that HDD or main board has some problem. Please replace HDD or main board with new one and check if the problem disappears. d) It seems that there is some critical issue in the USB connection between main board and OPE. Please try below steps. i) If WiFi module is installed, replace WiFi module with new one. ii) Check USB cable state between main board and OPE. iii) Replace the main board with new one. iv) Replace the OPE board with new one. |
| Error code: | S6-3122 |
| Display: | Network cable is disconnected. Check it. |
| Description: | Network cable is disconnected. Check it. |
| Causes: | Network cable is disconnected. |
| Remedy: | 1) Check if the green LED of the network port is on. 2) If not, unplug and reconnect the network cable. 3) If the problem persists, replace the main board(JC92-02742A). |
| Error code: | S6-3123, S6-3229, S6-322A |
| Description: | This IP address conflicts with that of other system. Check it. The IPv4 address assigned to wireless LAN conflicts with that of other system. Check it The IPv6 address assigned to wireless LAN conflicts with that of other system. Check it |
| Causes: | Network has some problem. (IP address conflicts with that of other system. |
| Remedy: | • Change the machine’s IP address. 1) Select “Machine Setup” on the touch screen. 2) Select “Networking Setting”. 3) “Log-In”. 4) Select “TCP/IP”. 5) Select the proper item for your machine. 6) Select “IP Setting”. 7) Select the proper item for your machine. 8) Change the IP address. |
| Error code: | S6-3128 |
| Display: | 802.1x authentication failed. Please Contact the System Administrator |
| Description: | There is no response when checking the ping test. ID or Password is incorrect. |
| Causes: | Network error. ( A authenticator(eg switch) rejected authentication. / There is no response when checking the ping test.) |
| Remedy: | 1) Change the IP adredd (Machine Setup > Network Setting > Login > TCP/IP > Select the network protocol > IP Setting 2) Inut the Network Login ID and Password correctly. |
| Error code: | S6-3224, S6-3225 |
| Description: | BOOTP error in wireless LAN. Switching to Auto IP. BOOTP error in wireless LAN. Reconfigure DHCP or static IP. |
| Causes: | BOOTP or DHCP server has a problem or IP address assignment is abnormal. |
| Remedy: | • Check the BOOTP or DHCP server. • If the server is normal, check the network setting. |
| Error code: | S6-3226, S6-3227 |
| Description: | DHCP error in wireless LAN. Switching to Auto IP. DHCP error in wireless LAN. Reconfigure BOOTP or static IP. |
| Causes: | BOOTP or DHCP server has a problem or IP address assignment is abnormal. |
| Remedy: | • Check the BOOTP or DHCP server. • If the server is normal, check the network setting. |
| Error code: | S7-1110 |
| Display: | Failure: #S7-1110. Turn off then on |
| Description: | Engine System Failure: #S7-1110. Turn off then on |
| Causes: | 24V power is abnormal. |
| Remedy: | 1) Check the 24V pin on SMPS board. If it is abnormal, replace the SMPS board. 2) Check the related cable. 3) If the SMPS is normal, replace the main board. |
| Error code: | S7-1210 |
| Display: | Failure: #S7-1210. Turn off then on |
| Description: | Engine System Failure: #S7-1110. Turn off then on |
| Causes: | 5V power is abnormal. |
| Remedy: | 1) Check the 5V pin on SMPS board. If it is abnormal, replace the SMPS board. 2) Check the related cable. 3) If the SMPS is normal, replace the main board. |
| Error code: | S7-2110 |
| Display: | Fuser Failure: #S7-2110. Turn off then on |
| Description: | Fuser Failure: #S7-2110. Turn off then on |
| Causes: | Heater control relay is abnormal. |
| Remedy: | 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) If the problem persists, replace the Fuser unit(110V : JC91-01158A, 220V : JC91-01157A). |
| Error code: | U1-2115 |
| Display: | Fuser Unit Failure: #U1-2115. Turn off then on. |
| Description: | Fuser Unit Failure: #U1-2115. Turn off then on. |
| Causes: | The pressure control unit(Cam unit)of the fuser is abnormal. |
| Remedy: | 1) Turn the machine off then open the side cover. 2) Remove and re-install the fuser unit, then turn the machine on. 3) If the problem persists, check the following : a) When the side-cover closes, check if the operation sound of the pressure control unit occurs. b) Check if the parts of the pressure control unit are abnormal. - Check if the shape of the CAM-REAR(JC66-03299A)) is broken. - Check if there are abnormal parts of the pressure control unit. c) Check if the fuser-motor is abnormal via SVC mode. 4) If the problem persists, replace the Fuser unit(110V : JC91-01158A, 220V : JC91-01157A). 5) If the problem persists, replace the pressure control unit or cam-motor or Main board(JC92-02742A). |
| Error code: | U1-2117, U1-212x |
| Description: | Fuser Unit Failure: #U1-21xx. Turn off then on. |
| Causes: | The temperature control of fuser unit is abnormal. The fuser temperature has dropped below the normal value. |
| Remedy: | 1) Turn the machine off then on. 2) Turn the machine off. Re-install the fuser unit. Then turn the machine on. 3) If the problem persists, remove the fuser unit. 4) Check the fuser components. • Check if the thermistor is assembled correctly. • Check if the thermostat is connected. • Check if the center and side lamps are in short status. (Measure the resistance value between the common-center and common-side.) 5) If there are any defective parts in step5, replace the fuser unit. 6) If the problem persists, replace these parts in regular sequence. • Fuser Drive Board • Main board • SMPS board |
| Error code: | U1-213x, U1-23xx |
| Description: | Fuser unit Failure: #U1-2xxx. Turn off then on. Call for service if the problem persists |
| Causes: | The temperature control of fuser unit is abnormal. (Open Heat Error or Low Heat Error or Over Heat Error) / Thermistor is defective. / Fuser unit connection is bad. |
| Remedy: | 1) After checking the fuser installation, turn the machine off then on. 2) Open the rear cover. Lift up the right side and release the rear cover. 3) If there is no problem, remove 4 screws. 4) Lift up the both levers. Then take off the fuser unit. 5) Remove the Frame-cover-upper after removing 2 screws. And measure the thermostat continuity. Check if the thermostat is opened. 6) Measure the LAMP-HALOGEN resistance value from the center and both sides. Check if it has the continuity. 7) Check if the Draw-connector harness is correct. Check its color. 8) Check if 2 thermistor connectors are connected properly. 9) Measure the Thermistor resistance value from the center and both sides. Check if it has the continuity. 10)Check if the thermistor connector on the main board is connected properly. 11) Check if the FDB connector is connected properly. 12)Check if the voltage in user environment is in this range (80V ~ 140V, 160V ~ 260V). 13)If there is no problems for above steps, update the firmware. 14)Replace the FDB. 15)If the problem persists, replace the SMPS. 16)If the problem persists, replace the main board. |
| Error code: | U1-234J, U1-234P |
| Description: | Fuser Unit Failure: #U1-234J. Turn off then on. Fuser Unit Failure: #U1-234P. Turn off then on. |
| Causes: | The temperature control of fuser unit is abnormal. The fuser temperature has risen above the normal value. |
| Remedy: | 1) Turn the machine off then on. 2) Turn the machine off. Re-install the fuser unit. Then turn the machine on. 3) If the problem persists, remove the fuser unit. 4) Check the fuser components. • Check if the thermistor is assembled correctly. • Check if the thermostat is connected. • Check if the center and side lamps are in short status. (Measure the resistance value between the common-center and common-side.) 5) If there are any defective parts in step5, replace the fuser unit. 6) If the problem persists, replace these parts in regular sequence. • Fuser Drive Board • Main board • SMPS board |
| Error code: | U2-1112 |
| Display: | Error #U2-1111 Turn off then on. |
| Description: | LSU Motor does not work normally. |
| Causes: | LSU motor does not operate or it operates abnormally. Motor ready signal is abnormal. |
| Remedy: | 1) Execute the LSU motor test in EDC mode. Check LSU motor operation sound. 2) If there is no sound, remove the right cover. Check if the LSU harness is connected on the main board properly. (picture-1) 3) If it is OK, remove the top cover. Check if the LSU harness is connected on LSU board properly. (picture- 2,3) 4) Check if the LSU harness is defective. (picture-4) 5) Reconnect the LSU harness and then execute the LSU motor test again. 6) If the problem persists, replace the LSU(JC97-04065A). 7) If the problem persists after replacing LSU, replace the main board. |
| Error code: | U2-1113 |
| Display: | Error #U2-1113 Turn off then on. |
| Description: | LSU Motor does not work normally. |
| Causes: | LSU Hsync signal can not be detected correctly. LSU Hsync signal is abnormal. |
| Remedy: | 1) Execute the LSU motor test in EDC mode. Check LSU motor operation sound. 2) If there is no sound, remove the right cover. Check if the LSU harness is connected on the main board properly. (picture-1) 3) If it is OK, remove the top cover. Check if the LSU harness is connected on LSU board properly. (picture- 2,3) 4) Check if the LSU harness is defective. (picture-4) 5) Reconnect the LSU harness and then execute the LSU motor test again. 6) If the problem persists, replace the LSU(JC97-04065A). 7) If the problem persists after replacing LSU, replace the main board. |
| Error code: | U3-3211, U3-3213, U3-3214 |
| Display: | U3-3211, U3-3213, U3-3214, U3-3311, U3-3313, U3-3314 Original paper jam / Original paper jam inside of scanner. Remove jam |
| Description: | Original paper jam inside of scanner |
| Causes: | Jam has occurred inside the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the Regi. sensor and Regi actuator. Push and release the regi actuator. Check if the pick up module returns the original position. If the sensor is defective, replace it(0604–001393). 3) If the regi sensor is OK, check the scan 1 sensor and reflect film. • If the scan 1 sensor is defective, replace it(0604–001381). • If the reflect film is contaminated, clean it. |
| Error code: | U3-3311, U3-3313, U3-3314 |
| Display: | U3-3211, U3-3213, U3-3214, U3-3311, U3-3313, U3-3314 Original paper jam / Original paper jam inside of scanner. Remove jam |
| Description: | Original paper jam inside of scanner |
| Causes: | Jam has occurred inside the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the Regi. sensor and Regi actuator. Push and release the regi actuator. Check if the pick up module returns the original position. If the sensor is defective, replace it(0604–001393). 3) If the regi sensor is OK, check the scan 1 sensor and reflect film. • If the scan 1 sensor is defective, replace it(0604–001381). • If the reflect film is contaminated, clean it. |
| Error code: | U3-3411, U3-3413, U3-3414 |
| Display: | Original paper jam inside of scanner. |
| Description: | Jam has occurred inside the DADF unit. |
| Causes: | Original jam has occurred around the scan in roller and regi roller. |
| Remedy: | 1) Open the DADF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the following: a) Check if the Regi. actuator(JC66-03148A) operates normally. b) Check if the Regi. sensor cable is connected correctly. c) If the connection is OK, replace the Regi. sensor(0604-001393). |
| Error code: | U3-3511, U3-3513, U3-3514 |
| Display: | Original paper jam inside of scanner. |
| Description: | Original paper jam inside of scanner. |
| Causes: | Jam has occurred inside the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If this error occurs continually, check the Regi. sensor and Regi actuator. Push and release the regi actuator. Check if the pick up module returns the original position. If the sensor is defective, replace it. 3) If the regi sensor is OK, check the scan 2 sensor and exit sensor. • If the scan 2 sensor is defective, replace it. • If the exit sensor is defective, replace it. |
| Error code: | U3-3611, U3-3613, U3-3614 |
| Description: | Original paper jam in the exit area of scanner |
| Causes: | Jam has occurred in exit area of the DSDF unit. |
| Remedy: | 1) Open the DSDF cover. If there is jammed paper, remove it. 2) If the regi sensor is OK, check the scan 2 sensor and exit sensor. • If the scan 2 sensor is defective, replace it. • If the exit sensor is defective, replace it. |
| Error code: | U3-3713, U3-3714 |
| Description: | Original paper jam in the exit area of scanner |
| Causes: | Original jam has occurred around the scan in roller and regi roller. |
| Remedy: | 1) Check if the pick up motor operates normally. 2) Open the DSDF cover. Check if the paper jam is occurred. 3) Pull the green lever of the Guide Exit Lower. Remove the jammed paper. 4) Check if there are any obstacles or contamination on the paper path. Remove it. 5) If the problem persists, check the exit sensor and connection. a) Remove the DSDF Unit and white sponge. b) Remove the Exit Lower after removing 4 screws. c) Check if the sensor and actuator are assembled correctly. 6) Push the white bar. Check if it returns in original condition. 7) Close the DSDF unit. |
