Samsung ProXpress M3325ND
Рейтинг
Модули
FRAME
COVER-MIDDLE LOWER
Frame Rear
DRIVE
PLATEN
DUPLEX
CASSETTE
COVER-FRONT
FRAME-ETC
MAIN
MP
SCANNER
OPE
Детали PLATEN
| Деталь: | COVER-TOP_INNER, SL-M4025ND,ABS,SPLIT GRA |
| Парткод: | JC63-04144A |
| Деталь: | FRAME-ETC, SL-M3375FD,SEC |
| Парткод: | JC93-00836D |
| Деталь: | MP, ML-4210ND,SEC |
| Парткод: | JC90-01044B |
| Деталь: | DRIVE, ML-4210ND,SEC |
| Парткод: | JC93-00544B |
| Деталь: | DRIVE-FEED1, ML-3750 |
| Парткод: | JC93-00545B |
| Деталь: | SPACER-CLUTCH, ML-2851ND/XAA,POLY,ID4,OD1 |
| Парткод: | JC60-00037A |
| Деталь: | CLUTCH-ELECTRIC, 2.5,24,1,120mA,200Ohm |
| Парткод: | JC47-00033A |
| Цена: | 1 200 ₽ |
| Деталь: | COVER-MIDDLE LOWER, SL-M3370FD,SEC |
| Парткод: | JC95-01847B |
| Деталь: | PBA-LIU, cuhead,CX95110-22Z,SPI,3.3V,90MM |
| Парткод: | JC92-02569A |
| Деталь: | GROUND-FAX, SL-M4075FR,PBS-C5210,0.2,65.2 |
| Парткод: | JC63-04068A |
| Деталь: | GROUND-EXIT, SCX-4833FD,SUS,0.2,99.3,28.2 |
| Парткод: | JC63-03090A |
| Деталь: | STACKER-MAIN, CLX-6260ND,ABS,2.2,90.3,67. |
| Парткод: | JC61-05515A |
| Деталь: | SPEAKER, 0.3W,8ohm,81dB,400Hz,50x16.4mm |
| Парткод: | 3001-002262 |
| Деталь: | STACKER-BIN_FULL, Magpie,PC,2,48.54,35.2, |
| Парткод: | JC61-04098A |
| Деталь: | PMO-SUB_M_STACKER, ML-1520,PC,3925.53.5 |
| Парткод: | JC72-01343A |
| Деталь: | COVER-PATH, SL-M4075FR,HIPS,HIPS-5197 |
| Парткод: | JC63-04185A |
| Деталь: | COVER-EXIT, SL-M4020ND,ABS+PC,2.5,250,62. |
| Парткод: | JC63-04136A |
| Деталь: | BRUSH-ANTISTATIC, SCX-4833FD,AL+THUNDERON |
| Парткод: | JC67-00055B |
| Деталь: | FRAME-REAR, ML-3710,SEC,WORLD |
| Парткод: | JC93-00334A |
| Деталь: | SPRING-ETC, SUS304,PI0.2,ID4.5,OD4.9,8.1, |
| Парткод: | 6107-002670 |
| Деталь: | BUSH-TX, ML-3471ND/SEE,POM(M90-44),2.5,16 |
| Парткод: | JC61-02158A |
| Деталь: | GUIDE-REAR, ML-3700ND,PC,2.0t,PATH |
| Парткод: | JC61-04084A |
| Деталь: | HOLDER-ACTUATOR, ML-3700,TEFLON,2.0,17.4 |
| Парткод: | JC61-04133A |
| Деталь: | ACTUATOR-EXIT, ML-3700ND,NYLON,2.0t,46.7, |
| Парткод: | JC66-02774A |
| Деталь: | ROLLER-IDLE_EXIT, ML-2851ND,PFA |
| Парткод: | JC66-01661A |
| Деталь: | ROLLER-SILICON_EXIT, ML-3700,SILICON |
| Парткод: | JC66-02955A |
| Деталь: | SHAFT-EXIT_F/UP, ML-3700ND,PET+GF45,236.4 |
| Парткод: | JC66-02773A |
| Деталь: | GEAR-EXIT_Z19, ML-3700ND,POM,1,19,NTR,21. |
| Парткод: | JC66-02777A |
| Деталь: | LABEL-ONE TOUCH, ML-3700,WHITE PET,0.1,7, |
| Парткод: | JC68-02610A |
| Деталь: | DRIVE, ML-4210ND,SEC |
| Парткод: | JC93-00544B |
| Деталь: | MOTOR BLDC, ML-4210ND,3/10,37,24,1200/190 |
| Парткод: | JC31-00075B |
| Деталь: | BRACKET-MOTOR, ML-3710,SECC,1.2,95,85 |
| Парткод: | JC61-04918A |
| Деталь: | GEAR-EXIT 95-81, ML-3310,POM,0.5/0.5,95/8 |
| Парткод: | JC66-02779A |
| Деталь: | GEAR-FEED 65-28, ML-3710,POM,0.5/1.0,65/2 |
| Парткод: | JC66-02790A |
| Деталь: | GEAR-FUSER DR IN 79, ML-3710,POM,0.5,79,N |
| Парткод: | JC66-02781A |
| Деталь: | GEAR-IDLE 59, ML-3710,POM,0.5,59,BLACK,F2 |
| Парткод: | JC66-02785A |
| Деталь: | GEAR-COUPLER 73, ML-3710,POM,0.5,73,BLACK |
| Парткод: | JC66-02787A |
| Деталь: | GEAR-OPC DR OUT 53, ML-3710,POM,0.5,53,BL |
| Парткод: | JC66-02788A |
| Деталь: | GEAR-IDLE 73, ML-3710,POM,0.5,73,BLACK,F2 |
| Парткод: | JC66-02786A |
| Деталь: | HUB-CLUTCH, ML-3710ND,POM,ID10.4,F20-02,N |
| Парткод: | JC70-00589A |
| Деталь: | SPRING-CS, SUS304WPB,D13,18.6,T1,ID11 |
| Парткод: | 6107-002785 |
| Деталь: | COUPLER, ML-3710ND,POM,OD25,NATURAL,F20-0 |
| Парткод: | JC67-00504A |
| Деталь: | GEAR-OPC DR IN 69, ML-3710,POM,0.5,69,BLA |
| Парткод: | JC66-02789A |
| Деталь: | COUPLER-CAM, ML-3710ND,PC,NH-1035,BLK |
| Парткод: | JC67-00503A |
| Деталь: | GEAR-FUSER DR 29, ML-3710ND,PA66,1.0,29,B |
| Парткод: | JC66-02782A |
| Деталь: | BRACKET-GEAR, ML-3710,SECC,1.2,133,214 |
| Парткод: | JC61-04916A |
| Деталь: | GEAR-HUB CLUTCH, POM,11.3,11.3,11.3,NW-02 |
| Парткод: | JC66-00340A |
| Цена: | 220 ₽ |
| Деталь: | PLATEN-UPPER, CLX-6260ND |
| Парткод: | JC97-04167A |
| Деталь: | PLATEN-LOWER, SCX-5742 |
| Парткод: | JC97-04346A |
| Деталь: | COVER-PLATEN UPPER, CLX-6260ND,HIPS,W326, |
| Парткод: | JC63-03837A |
| Деталь: | GLASS-ADF, 25228.5,2.8T |
| Парткод: | JC01-00058A |
| Деталь: | BRACKET-GUIDE PATH, CLX-6260ND,EGI-SECC,T |
| Парткод: | JC61-05642A |
| Деталь: | GROUND-PLATEN UPPER, CLX-6260ND,PBS-C5210 |
| Парткод: | JC63-03839A |
| Деталь: | GLASS-PLATEN, 345.8249,2.8 |
| Парткод: | JC01-00059A |
| Деталь: | PLATEN- FH, SCX-5742FR |
| Парткод: | JC97-04307A |
| Деталь: | FRAME-PLATEN, CLX-6260ND,HIPS,W302,L401.1 |
| Парткод: | JC61-05632A |
| Деталь: | GUIDE-CIS REAR, CLX-6260ND,POM,W7.4,L43.2 |
| Парткод: | JC61-05641A |
| Деталь: | CONTACT IMAGE SENSOR, 217mm,10368dot,0.5m |
| Парткод: | 0609-001482 |
| Деталь: | BRACKET-CIS, CLX-6260ND,ABS+PC,W40.44,L23 |
| Парткод: | JC61-05646A |
| Деталь: | PHOTO-INTERRUPTER, TR,DIP-4,BK |
| Парткод: | 0604-001415 |
| Цена: | 240 ₽ |
| Деталь: | BELT-TIMING GEAR, 759teeth,poly urethan,b |
| Парткод: | 6602-002970 |
| Деталь: | PLATEN-DRIVETRAIN, CLX-6260ND |
| Парткод: | JC97-04170A |
| Цена: | 2 000 ₽ |
| Деталь: | GUIDE-CIS FRONT, CLX-6260ND,POM,W7.4,L43. |
| Парткод: | JC61-05634A |
| Деталь: | DUPLEX, ML-4210ND,SEC |
| Парткод: | JC90-01031D |
| Деталь: | ROLLER-FEED_DUP2, ML-2851ND,NBR,SUM22,4 |
| Парткод: | JC66-01657A |
| Деталь: | ROLLER-FEED_DUP, ML-3560,NBR,SUM22,4 |
| Парткод: | JC66-00901A |
| Деталь: | ROLLER-DUPLEX_IDLE, ML-5015ND,POM,SW-01 |
| Парткод: | JC66-02980A |
| Деталь: | SPRING-TS, SUS304,NO,0.55,4.05,3.5,2-5.8, |
| Парткод: | 6107-003256 |
| Деталь: | GUIDE-PAPER_DUPLEX, ML-3700ND,PC,1.5,16.2 |
| Парткод: | JC61-04055A |
| Деталь: | PULLEY-18_DUP, ML-3560,POM,HB,WHITE, 4.1 |
| Парткод: | JC66-00899A |
| Деталь: | BRACKET-DUPLEX_ALIGN, ML-3700ND,SECC,0.6, |
| Парткод: | JC61-04053A |
| Деталь: | GEAR-EXIT F/DOWN, ML-4500,POM,0.8,BLACK,F |
| Парткод: | JC66-00038A |
| Деталь: | BELT-TIMING GEAR, 32S2M152,CR+GF+NF,T3.2, |
| Парткод: | 6602-001588 |
| Деталь: | BELT-FLAT RUBBER, L280, W3.2, S2M, 140 |
| Парткод: | JC66-20901A |
| Деталь: | CASSETTE, ML-4210ND,SEC |
| Парткод: | JC90-01143C |
| Деталь: | CASSETTE-COVER HANDLE, ML-4210ND,SEC |
| Парткод: | JC90-01174E |
| Деталь: | CASSETTE-FRAME, ML-4210ND,SEC |
| Парткод: | JC90-01173C |
| Деталь: | HANDLE-CASSETTE, ML-4210ND,HIPS,2.5,287.4 |
| Парткод: | JC64-00890B |
| Деталь: | INDICATOR-PAPER, ML-4210ND,ABS,2.5,CREAM |
| Парткод: | JC64-00609E |
| Деталь: | CASSETTE-GUIDE RIGHT, ML-2955ND,SEE |
| Парткод: | JC90-01106A |
| Деталь: | CASSETTE-GUIDE REAR, ML-4210ND,SEC |
| Парткод: | JC90-01105C |
| Деталь: | CASSETTE SUB-RETARD, ML-4210ND,EPDM |
| Парткод: | JC90-01063B |
| Деталь: | RPR-PAD CASSETTE, ML-1510,Urethan Sponge, |
| Парткод: | JC73-00141A |
| Цена: | 80 ₽ |
| Деталь: | GEAR-PINION, ML-2950ND,POM,0.5,32,3.9,WHI |
| Парткод: | JC66-03004A |
| Деталь: | LOCKER-PLATE, ML-3710,POM,NTR,138.5, 29.5 |
| Парткод: | JC64-00611A |
| Деталь: | LOCKER-CASSETTE, ML-3710,POM,NTR,41.5, 15 |
| Парткод: | JC64-00610A |
| Деталь: | GROUND-CASSETTE, SUS,0.2,UNC |
| Парткод: | JC63-02932A |
| Деталь: | COVER-CASSETTE, ML-4210ND,ABS,2.5,21.4,71 |
| Парткод: | JC63-02917D |
| Деталь: | PLATE-KNOCK UP, ML-3310ND,EGI-SECC,0.8,26 |
| Парткод: | JC61-04922A |
| Деталь: | FRAME-CASSETTE, ML-4210ND,ABS,Split gray, |
| Парткод: | JC61-04920D |
| Деталь: | GUIDE-ADJUST_L, ML-2950ND,ABS,2.0,135.52, |
| Парткод: | JC61-04397A |
| Деталь: | HOLDER-ROLLER, ML-3710ND,ABS,2,66,39,HB |
| Парткод: | JC61-04327A |
| Цена: | 280 ₽ |
| Деталь: | SPRING-CS, SWP,ZINC,0.9,17.9,56.3,17,18.8 |
| Парткод: | 6107-002779 |
| Деталь: | COVER-FRONT, SL-M3325ND,SEC,CREAM WHITE |
| Парткод: | JC95-01840B |
| Деталь: | COVER-FRONT, ML-4210ND,HIPS,2.5,365.6,256 |
| Парткод: | JC63-04134B |
| Деталь: | PHOTO-INTERRUPTER, TR,DIP-4,BK |
| Парткод: | 0604-001415 |
| Цена: | 240 ₽ |
| Деталь: | SPRING-TS, SWPB,1.0,12.1,12.1,3.05,3.05 |
| Парткод: | 6107-003474 |
| Деталь: | LOCKER-FRONT_R, CLP-310,POM,BLACK,D-Type |
| Парткод: | JC64-00368A |
| Деталь: | HARNESS-ZCRUM JOINT, SL-M4020ND,UL10272,7 |
| Парткод: | JC39-02008A |
| Деталь: | COVER-FRONT_INNER, ML-4210ND,HIPS,2.5,284 |
| Парткод: | JC63-04190A |
| Деталь: | BUTTON-FRONT, ML-4210ND,ABS,62.1,SPLIT BR |
| Парткод: | JC64-00888A |
| Деталь: | PBA-CRUM JOINT, ML-2975DW,SEC,3.3V,2L,FR- |
| Парткод: | JC92-02611A |
| Деталь: | COVER-MANUAL, SL-M4020ND,HIPS,2.7,287.5,1 |
| Парткод: | JC63-04147B |
| Деталь: | GUIDE-FRAME DUPLEX, ML-3700,ABS,2.3,250,5 |
| Парткод: | JC61-04064A |
| Деталь: | SHEET-DUPLEX PATH, ML-3710,PET+TAPE NITTO |
| Парткод: | JC63-02956A |
| Деталь: | BUSH-M-FEED IDLE, ML-1710,POM,2.1,4.2 |
| Парткод: | JC61-00585A |
| Деталь: | PLATE-P-PUSH BUSHING, SCX-4920N,EGI-SECC, |
| Парткод: | JC61-00914A |
| Деталь: | SHAFT-FEED IDLE, ML-1510,SUM 24L,223,8,ST |
| Парткод: | JC66-00527A |
| Цена: | 340 ₽ |
| Деталь: | LEVER-COUPLING, ML-3710,PC,3.0,184.4,126. |
| Парткод: | JC66-02770A |
| Деталь: | SPACER-CLUTCH, ML-2851ND/XAA,POLY,ID4,OD1 |
| Парткод: | JC60-00037A |
| Деталь: | ROLLER-FEED, ML-3700,EPDM,SUM22,5 |
| Парткод: | JC66-02797A |
| Цена: | 550 ₽ |
| Деталь: | CLUTCH-ELECTRIC, 2.5,24,1,120mA,200Ohm |
| Парткод: | JC47-00033A |
| Цена: | 1 200 ₽ |
| Деталь: | CLUTCH-ELECTRIC, 2.5,45,0.6,120mA,200Ohm |
| Парткод: | JC47-00036B |
| Цена: | 750 ₽ |
| Деталь: | GEAR-EXIT IDLE 96, ML-3310,POM,0.5,96,NTR |
| Парткод: | JC66-02778A |
| Деталь: | GEAR-EXIT 65, ML-3310,POM,0.5,65,NTR,F20- |
| Парткод: | JC66-02780A |
| Деталь: | GROUND-BRKT GEAR, ML-3700,SUS,0.2,18,18,G |
| Парткод: | JC63-02875A |
| Деталь: | LOCK SLIDER, ML-1710,POM(DELIN 900P),WHT |
| Парткод: | JC72-00983A |
| Деталь: | PLATE-P-SAW, ML-1400,SUS304,0.15,15.1,216 |
| Парткод: | JC61-00604A |
| Деталь: | ROLLER-FEED REGI, ML-3200,EPDM,SUM22,6 |
| Парткод: | JC66-02834A |
| Деталь: | ACTUATOR-EMPTY, ML-3710,POM,3.0,43.1,31.2 |
| Парткод: | JC66-02762A |
| Деталь: | ACTUATOR-REGI, ML-3710,PC+GF,3.0,30.6,21. |
| Парткод: | JC66-02763A |
| Деталь: | ACTUATOR-FEED, ML-3710,PC+GF,3.0,17.5,20. |
| Парткод: | JC66-02764A |
| Деталь: | PHOTO-INTERRUPTER, TR,75mW,BGA,TR |
| Парткод: | 0604-001393 |
| Деталь: | FRAME-DUPLEX PATH_EX, ML-2851ND,HIPS,BLAC |
| Парткод: | JC61-02752A |
| Деталь: | PLATE-FRAME BOTTOM, ML-3700,EGI-SECC,1.0, |
| Парткод: | JC61-04069A |
| Деталь: | ROLLER-M_IDLE SCF, SCX-6345N,POM,500CL |
| Парткод: | JC66-01022A |
| Цена: | 260 ₽ |
| Деталь: | CAP-HARNESS, ML-2851ND,ABS V0,2,241.1,76. |
| Парткод: | JC67-00291A |
| Деталь: | BRACKET-SWING DUPLEX, ML-2851ND/XAA,PPS,5 |
| Парткод: | JC61-02265A |
| Деталь: | GEAR-RDCN 23/23, ML-2851ND/XAA,POM,0.6/0. |
| Парткод: | JC66-01651A |
| Цена: | 260 ₽ |
| Деталь: | FAN, Type4,24,100mA,2.794mmH20,0.374m3/m |
| Парткод: | JC31-00146A |
| Деталь: | SHAFT, ML-5000A,STAINLESS-STS303,6,NI,T4. |
| Парткод: | JC70-40912A |
| Деталь: | FRAME-ROLLER DECURL, ML-3700 |
| Парткод: | JC93-00324A |
| Деталь: | GROUND-BRKT PAPER, ML-3700,SUS,0.2,54,43. |
| Парткод: | JC63-02874A |
| Деталь: | GROUND-HVPS, ML-3700,SUS,0.2,74.3,15,GROU |
| Парткод: | JC63-02876A |
| Деталь: | GROUND-BRACKET LSU, ML-3700,SUS,0.2,48.5, |
| Парткод: | JC63-02877A |
| Деталь: | HVPS, 24V,21.6V27.6V,MAX 5KV,MAX-2KV,600 |
| Парткод: | JC44-00197A |
| Цена: | 2 800 ₽ |
| Деталь: | FRAME-ROLLER EXIT, ML-3700 |
| Парткод: | JC93-00323A |
| Деталь: | BRUSH-ANTISTATIC 531P, SF-531P,AL+THUNDER |
| Парткод: | JC67-00055A |
| Деталь: | HOLDER-EXIT SENSOR, ML-3710,ABS,2,45.5,44 |
| Парткод: | JC61-04067A |
| Деталь: | GEAR-SWING DR 19, ML-2851ND/XAA,POM,0.6,1 |
| Парткод: | JC66-01635A |
| Деталь: | BRACKET-LSU, ML-3750ND,EGI-SECC,1.0T,305, |
| Парткод: | JC61-04915A |
| Деталь: | GUIDE-TR RIB, ABS,2.3,239.2,79.8,BLACK,PA |
| Парткод: | JC61-04091A |
| Деталь: | ROLLER-TRANSFER, Magpie,15.0 (mm),NBR+ECO |
| Парткод: | JC66-02842A |
| Цена: | 1 200 ₽ |
| Деталь: | PLATE-EARTH-TRANSFER, ML-2851ND,EGI-SECC, |
| Парткод: | JC61-02236A |
| Деталь: | CORE ROTOR, ML-1710,POM(M90-44),BLK |
| Парткод: | JC72-00985A |
| Цена: | 280 ₽ |
| Деталь: | TERMINAL-TR, ML-3700,SUS304,0.5PI |
| Парткод: | JC65-00047A |
| Деталь: | CABLE CLAMP, DACS-3N,16.67 4,Nylon66,BL |
| Парткод: | 6502-001130 |
| Деталь: | SHAFT, ML-2150,POM,BLK,DE8903 |
| Парткод: | JC72-41191B |
| Цена: | 430 ₽ |
| Деталь: | RUBBER-PICK UP, ML-3700,EPDM80%+IR20% |
| Парткод: | JC73-00340A |
| Цена: | 230 ₽ |
| Деталь: | SHIELD-CONTROLLER, SL-M4025ND,EGI-SECC,0. |
| Парткод: | JC63-04078A |
| Деталь: | HARNESS-REARCOVER & BINFULL SENSOR, ML-3710 |
| Парткод: | JC39-01469A |
| Деталь: | HARNESS-AC INLET-1, ML-3710,UL1617,3pin,W |
| Парткод: | JC39-01482A |
| Деталь: | HOLDER-BRKT_LSU_RIGHT, ML-3750ND,PC+GF,T2 |
| Парткод: | JC61-04912A |
| Деталь: | HOLDER-BRKT_LSU_LEFT, ML-3750ND,PC+GF,T2. |
| Парткод: | JC61-04911A |
| Деталь: | GROUND-BRKT EXTENSION, ML-3750ND,SUS,0.2, |
| Парткод: | JC63-03449A |
| Деталь: | GEAR-FEED IDLE 29, ML-3710,POM,1,29,BLACK |
| Парткод: | JC66-03311A |
| Деталь: | COVER-FRONT, SL-M3325ND,SEC,CREAM WHITE |
| Парткод: | JC95-01840B |
| Деталь: | CASSETTE, ML-4210ND,SEC |
| Парткод: | JC90-01143C |
| Деталь: | COVER-RIGHT, SL-M4075FR,SEC |
| Парткод: | JC95-01838B |
| Деталь: | FRAME, SL-M3375FD,SEC,SEE |
| Парткод: | JC93-00835H |
| Деталь: | COVER-LEFT, ML-4210ND,HIPS,2.5,353.4,256, |
| Парткод: | JC63-04137B |
| Деталь: | SMPS-V2, SCX-5737FW,PSPN-Type3-V2,Flyback |
| Парткод: | JC44-00090E |
| Цена: | 5 400 ₽ |
| Деталь: | PBA-MAIN, SL-M3375FD,PBA-MAIN,190118.2 |
| Парткод: | JC92-02603M |
| Деталь: | DUPLEX, ML-4210ND,SEC |
| Парткод: | JC90-01031D |
| Деталь: | FUSER, ML-3700,SEC,WORLD,220V |
| Парткод: | JC91-01024A |
| Цена: | 5 600 ₽ |
| Деталь: | FUSER, ML-3700,SEC,WORLD,110V |
| Парткод: | JC91-01023A |
| Деталь: | FRAME-REAR, ML-3710,SEC,WORLD |
| Парткод: | JC93-00334A |
| Деталь: | COVER-REAR, SL-M4075FR,SEC |
| Парткод: | JC95-01303D |
| Деталь: | LSU, ML-3750,SEC,Single,A4(Ltr),600,S1,78 |
| Парткод: | JC97-04065A |
| Цена: | 3 900 ₽ |
| Деталь: | COVER-MIDDLE LOWER, SL-M3370FD,SEC |
| Парткод: | JC95-01847B |
| Деталь: | COVER-MIDDLE UPPER ADF, SL-M3370FD,SEC |
| Парткод: | JC95-01839B |
| Деталь: | OPE, SL-M3375FD,SEC,ADF, English(OVERLAY) |
| Парткод: | JC97-04320F |
| Деталь: | SCANNER, SCX-5742FR |
| Парткод: | JC97-04315A |
| Деталь: | COVER-RIGHT, SL-M4020ND,ABS+PC,2.5,354.3, |
| Парткод: | JC63-04140B |
| Деталь: | COVER-DIMM, SL-M4025ND,ABS+PC,CREAM WHITE |
| Парткод: | JC63-04141B |
| Деталь: | MP-GUIDE LOWER, ML-4210ND,SEC |
| Парткод: | JC90-01042B |
| Деталь: | MP-HOLDER IDLE, ML-4210ND,SEC |
| Парткод: | JC90-01038C |
| Деталь: | ADJUST-MANUAL_R, ML-2851ND,HIPS,43,26.3,M |
| Парткод: | JC70-00547A |
| Деталь: | ADJUST-MANUAL_L, ML-2851ND,HIPS,43,26.3,M |
| Парткод: | JC70-00546A |
| Деталь: | ADJUST, ML-1710,POM,NTR,ADJUST/UNC |
| Парткод: | JC70-00304A |
| Деталь: | ROLLER-IDLE, ML-3700,POM,NW-02 |
| Парткод: | JC66-02798A |
| Деталь: | SCANNER, SCX-5742FR |
| Парткод: | JC97-04315A |
| Деталь: | ADF, CLX-6260ND |
| Парткод: | JC97-04164A |
| Деталь: | SHEET-WHITE, SCX-4833FD,White_PP+Black_Sp |
| Парткод: | JC01-00060A |
| Деталь: | COVER-CONNECTOR, CLX-6260ND,HIPS,W27,L58. |
| Парткод: | JC63-03836A |
| Деталь: | PLATEN, SCX-5742FR |
| Парткод: | JC97-04313A |
| Деталь: | COVER-SCAN, CLX-6260ND,HIPS,3.2,14.3,10.4 |
| Парткод: | JC63-03834A |
| Деталь: | PLATEN-LOWER ADF, SCX-5742FD |
| Парткод: | JC97-04345A |
| Деталь: | PBA-ADF, SCX-4729FD,SEC,ADF,60x25mm,FR-1, |
| Парткод: | JC92-02426A |
| Деталь: | GROUND-SCAN LOWER, CLX-4195FW,STAINLESS-S |
| Парткод: | JC63-03716A |
| Деталь: | OPE, SL-M3375FD,SEC,ADF, English(OVERLAY) |
| Парткод: | JC97-04320F |
| Деталь: | PBA-OPE, CLX-6260FD,SEC,OPE,FR1,1L,4LINE |
| Парткод: | JC92-02522A |
| Деталь: | COVER-LCD, CLX-4195FN,PC,73.4,52.65 |
| Парткод: | JC63-03728A |
| Деталь: | HOLDER-KEY, CLX-6260ND,ABS,66.9,51.2,BLAC |
| Парткод: | JC61-05625A |
| Деталь: | KEY-NUMERICAL, CLX-6260ND,ABS,60.06,47.2, |
| Парткод: | JC64-00817A |
| Деталь: | GROUND-LCD, CLX-4195FN,STAINLESS-STS304,0 |
| Парткод: | JC63-03718A |
| Деталь: | COVER-OPE, SL-M3375FD,ABS,138.6,382.3,SEC |
| Парткод: | JC63-03781S |
Коды ошибок
A1-1110
C1-1110, C1-1120, C1-1144
C1-1150, C1-1160, C1-1170
C1-1310, C1-1411
C1-1512
C1-1710, C1-1711, C1-1712
C2–1110, C2–1120, C2–1150
C2–1160, C2–1170
C2-1411
C2-1512
C2-1710, C2-1711, C2-1712
C3–1110, C3–1120, C3–1144
C3-1410
C3-1510
C9-1112
C9-1115
C9-1122
C9-1125
H1-1210
H1-1220
H1-1230
H1-1240
H1-1252, H1-1254
M1-1110
M1-1610
M1-5112, M1-5113, M1-5120
M1–5612
M2-1110
M2-2210
M3–1110
M3-2130
S2-4120
S6–3123
S6–3128
U1–2315, U1–2320, U1–2330
U1–2334, U1–2340
U2-1112, U2-1113
Описание
| Error code: | A1-1110 |
| Display: | Error #A1-1110 Turn off then on |
| Description: | Main Motor Failure: #A1-1110. Turn off then on. Call for service if the problem persists |
| Causes: | After working the main BLDC motor, the Ready signal has not occurred within 1 sec. |
| Remedy: | 1) Turn the machine off then on. If the error persists, refer to the following. 2) Check if the motor connector on the main board is connected properly. Reconnect it. 3) OPC coupler has overloaded. After removing the imaging unit, rotate the OPC coupler. (Spec : 6 kgf.cm) If there is any damage, the OPC coupler can’t rotate well. Replace the imaging unit. 4) The main BLDC motor is defective. • Unplug the connector from the motor carefully. • Replace the main BLDC motor with new one. 5) If the problem persists, replace the main board. |
| Error code: | C1-1110, C1-1120, C1-1144 |
| Display: | Prepare new cartridge. Replace new cartridge. |
| Description: | The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life. |
| Remedy: | NOTE These errors are for M3325/3825/4025. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one. |
| Error code: | C1-1150, C1-1160, C1-1170 |
| Display: | Prepare new cartridge. Replace new cartridge. |
| Description: | The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life. |
| Remedy: | NOTE These errors are for M3325/3825/4025. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one. |
| Error code: | C1-1310, C1-1411 |
| Display: | Error: #C1-1310 Install toner Install toner. |
| Description: | The toner cartridge is not installed. |
| Remedy: | NOTE These errors are for M3325/3825/4025. 1) Turn the machine off then on. 2) Open the front cover. 3) Check if the toner cartridge is installed. If yes, remove and reinstall it. 4) If the problem persists, replace the toner cartridge with new one. |
| Error code: | C1-1512 |
| Display: | Toner cartridge is not compatible. Check users guide. |
| Description: | Toner cartridge is not compatible. Check users guide. |
| Causes: | Toner cartridge is not compatible. |
| Remedy: | 1) Print the supply information report. Check information of the toner cartridge. 2) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one. |
| Error code: | C1-1710, C1-1711, C1-1712 |
| Display: | Error: #C1-1710 Call for Service Error: #C1-1711 Call for Service Error: #C1-1712 Call for Service |
| Description: | The machine can’t detect the CRUM chip of the toner cartridge. |
| Causes: | The data of CRUM is not detected. / CRUM is defective. |
| Remedy: | NOTE These errors are for M3325/3825/4025. 1) Open the front cover. 2) Remove the toner cartridge. 3) Check if the CRUM terminal is contaminated. Clean it. 4) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one. |
| Error code: | C2–1110, C2–1120, C2–1150 |
| Display: | Prepare new cartridge. Replace new cartridge. |
| Description: | The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life. |
| Remedy: | NOTE These errors are for M3320/3820/4020. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one. |
| Error code: | C2–1160, C2–1170 |
| Display: | Prepare new cartridge. Replace new cartridge. |
| Description: | The remaining toner cartridge is less than 10% / The toner cartridge is at the end of its life. |
| Remedy: | NOTE These errors are for M3320/3820/4020. Check the life remaining of the toner cartridge. If its life is at the end, turn the machine off and replace the toner cartridge with new one. |
| Error code: | C2-1411 |
| Display: | Toner Not Installed / Toner cartridge is not installed. Install it |
| Description: | The toner cartridge is not installed. |
| Remedy: | This error is for M3370/3870/4070/4072FD. 1) Turn the machine off then on. 2) Open the front cover. 3) Check if the toner cartridge is installed. If yes, remove and reinstall it. 4) If the problem persists, replace the toner cartridge with new one. |
| Error code: | C2-1512 |
| Display: | Toner Not Compatible / Toner cartridge is not compatible. Check guide |
| Description: | Toner cartridge is not compatible. |
| Causes: | Toner cartridge is not compatible. |
| Remedy: | This error is for M3370/3870/4070. 1) Open the front cover. 2) Remove the toner cartridge. 3) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one. |
| Error code: | C2-1710, C2-1711, C2-1712 |
| Display: | Error: #C2-1710 Call for Service Error: #C1-1711 Call for Service Error: #C1-1712 Call for Service |
| Description: | Toner Cartridge Failure: #C2-1710. Call for service Toner Cartridge Failure: #C2-1711. Call for service Toner Cartridge Failure: #C2-1712. Call for service |
| Causes: | The data of CRUM is not detected. / CRUM is defective. |
| Remedy: | 1) Open the front cover. Check if the toner cartridge is installed. 2) Remove and reinstall the toner cartridge. 3) Check if the contact terminal is contaminated or broken. Clean the contact terminal. 4) Check if the CRUM harness is connected correctly. Reconnect it. 5) If the harness is defective, replace it. 6) If the problem persists, replace the toner cartridge with new one. |
| Error code: | C3–1110, C3–1120, C3–1144 |
| Display: | Prepare new cartridge. Replace new cartridge. |
| Description: | The remaining imaging unit is less than 10% / The imaging unit is at the end of its life. |
| Remedy: | NOTE These errors are for M3325/3825/4025. Check the life remaining of the imaging unit. If its life is at the end, turn the machine off and replace the imaging unit with new one. |
| Error code: | C3-1410 |
| Display: | IMG. Not Installed / Imaging unit is not installed. Install the unit |
| Description: | Imaging unitis not installed. Install the cartridge |
| Causes: | The Imaging unit is not installed. / The machine can’t detect the Imaging unit. |
| Remedy: | 1) Turn the machine off then on. 2) Remove the Imaging unit, then reinstall the toner cartridge. 3) Check if the CRUM contact area is contaminated. Clean it. |
| Error code: | C3-1510 |
| Display: | IMG. Not compatible / Imaging unit is not compatible. Check guide |
| Description: | Imaging unit is not compatible. |
| Remedy: | This error is for M3320/3820/4020. 1) Open the front cover. 2) Remove the toner cartridge and imaging unit. 3) If the imaging unit is not a Samsung genuine imaging unit, replace with new one. |
| Error code: | C9-1112 |
| Display: | Replace pickup roller / Replace with new tray 1 pickup roller |
| Description: | Tray1 pick up roller is worn out. |
| Remedy: | 1) Remove the tray 1 cassette. 2) Remove the duplex unit. 3) Pull the small tap down, then release the pick up roller(JC73-00340A). 4. Alignment and Troubleshooting |
| Error code: | C9-1115 |
| Display: | Replace retard roller / Replace with new tray 1 retard roller |
| Description: | Tray1 reverse roller is worn out. |
| Causes: | The pick up / forward / separation rollers for tray1 are at the end of its life. |
| Remedy: | 1) Remove the tray1 cassette. 2) Remove the reverse roller(JC90-01032A). |
| Error code: | C9-1122 |
| Display: | Replace pickup roller / Replace with new tray 2 pickup roller |
| Description: | Tray2 pick up roller is worn out. |
| Remedy: | 1) Remove the Tray 2 cassette. 2) See the bottom of the SCF Unit. 3) Pull the small tap down, then release the pick up roller(JC97-02259A). |
| Error code: | C9-1125 |
| Display: | Replace retard roller / Replace with new tray 2 retard roller |
| Description: | Tray2 reverse roller is worn out. |
| Remedy: | 1) Remove the Tray 2 cassette. 2) Open the cassette cover. 3) Pull the small tap down, then release the reverse roller(JC97-02259A). |
| Error code: | H1-1210 |
| Display: | Paper jam in Tray2. |
| Description: | Paper Jam in Tray 2 |
| Causes: | The jammed paper has occurred in the tray2. |
| Remedy: | 1) Remove the jammed paper. 2) If the jammed paper occurs continually, check the followings. a) Check if the pick up/forward/reverse roller are worn out or contaminated. Clean the contaminated part or replace it. b) Check if the actuator is assembled correctly. 3) If the pick up clutch is defective, replace it. |
| Error code: | H1-1220 |
| Display: | Tray 2 Door Open. Close it |
| Description: | Optional cassette is not installed properly |
| Causes: | Tray 2 door is open. |
| Remedy: | 1) Remove and reinstall the Tray2 cassette. 2) Check the cassette detection sensor. • Check if the connection between sensor and main board is OK. Reconnect the harness. • If the sensor(JC34-00001A) is defective, replace it. 3) If the problem persists, replace the SCF main board(JC92-02636A). |
| Error code: | H1-1230 |
| Display: | Error: #H1-1230 / Input System Failure: #H1-1230. Check tray 2 connection |
| Description: | Communication error has occurred. |
| Causes: | The communication error between the tray 2 and the main machine has occurred. |
| Remedy: | 1) Turn the machine off then on. 2) If the problem persists, turn the machine off. 3) Remove the SCF right cover. (Refer to 3.3.23.1) 4) Check if the interface connector is connected to the SCF main board. If the interface connector is defective, replace it. 5) If the problem persists, replace the SCF main board.(JC92-02636A) |
| Error code: | H1-1240 |
| Display: | Tray2 Not Install |
| Description: | Optional cassette is not installed properly. |
| Remedy: | 1) Remove and reinstall the Tray2 cassette. 2) Check the cassette detection sensor. • Check if the connection between sensor and main board is OK. Reconnect the harness. • If the sensor(JC34-00001A) is defective, replace it. 3) If the problem persists, replace the SCF main board(JC92-02636A). |
| Error code: | H1-1252, H1-1254 |
| Display: | Paper is empty in Tray2 |
| Description: | There is no paper in the tray2. / Actuator-Paper Empty or photo sensor is defective. |
| Causes: | Paper is empty in Tray2. |
| Remedy: | 1) Load the paper in the tray2. 2) If the problem persists, turn the machine off and check the following. 3) If the Actuator-Paper Empty is defective, replace it. 4) If the Photo Sensor(0604-001325) is defective, replace it. Check if the connector is connected properly. 5) If the problem persists, replace the SCF main board.(JC92-02636A) |
| Error code: | M1-1110 |
| Display: | Paper Jam in Tray1. |
| Description: | Paper jam in tray 1. Please remove the paper |
| Causes: | The jammed paper has occurred in the tray. |
| Remedy: | 1) Clear the jam from the tray1. 2) Remove the tray. Check if the loaded paper is in proper place. Align it. 3) If the jammed paper occurred before entering it to the separation roller, check the Sheet Retard / Pickup roller / Forward roller / CST Knock up / CST Knock up Spring. 4) If the jammed paper occurred after entering it to the separation roller, check the Ribs in paper path. |
| Error code: | M1-1610 |
| Display: | Paper jam in MP Tray. |
| Description: | Paper Jamin MP tray |
| Causes: | The jammed paper has occurred in the MP tray. |
| Remedy: | 1) Remove the jammed paper. 2) If the jammed paper occurs continually, check the followings. a) Check if the pick up/forward/reverse roller are worn out or contaminated. Clean the contaminated part or replace it. b) Check if the actuator is assembled correctly. 3) If the pick up clutch is defective, replace it. 4) If the problem persists, replace the MP unit. |
| Error code: | M1-5112, M1-5113, M1-5120 |
| Display: | Paper is empty in tray 1. Paper empty in all tray |
| Description: | Paper is empty in tray 1. Load paper Paper is empty in all tray. Load paper Paper is empty in MP tray. Load paper Paper is empty in manual feeder. Load paper |
| Causes: | Paper is empty in tray1 or manual feeder. / Paper is loaded in tray but the machine detects empty status. |
| Remedy: | 1) Load the paper in tray1 or manual feeder. 2) If the problem persists, check the following. 3) Check if the empty actuator works normally. If it is defective or broken, replace it. 4) If the actuator operation is OK, check the empty sensor. Reconnect the sensor connector. If the sensor is defective, replace it. |
| Error code: | M1–5612 |
| Display: | Paper is empty in all tray. Load paper |
| Description: | Paper is empty in MP tray. |
| Remedy: | 1) Check if the paper is loaded in MP tray. Load the paper. 2) Check if the MP empty actuator is assembled correctly. If it is broken or deformed, replace it. 3) If the MP empty sensor harness is connected correctly. If the harness is defective, replace it. 4) If the MP empty sensor is defective, replace it. |
| Error code: | M2-1110 |
| Display: | Paper Jam inside machine. |
| Description: | Paper jam inside of machine. Please remove the paper |
| Causes: | A paper jam was detected at the feed sensor. |
| Remedy: | 1) Remove the jammed paper. If the error persists, check the followings. 2) Check if the feed/regi sensor connector is connected properly. Reconnect the harness. 3) Check if the regi./feed actuator works normally. If it is defective or broken, replace it. 4) If the photo sensor is defective, replace the regi/feed sensor PBA. |
| Error code: | M2-2210 |
| Display: | Jam inside of duplex |
| Description: | A paper jam was detected in the bottom of duplex. |
| Remedy: | 1) Remove the jammed paper. 2) Remove the contamination or obstacles in the paper path. 3) If this jam error occur continually, replace the duplex unit. |
| Error code: | M3–1110 |
| Display: | Paper Jam in exit area |
| Description: | A paper jam was detected in the exit area. |
| Remedy: | 1) Open the rear cover. Remove the jammed paper. - 2) Check if the Guide-Change Duplex of the rear cover is defective. 3) Check if the exit sensor and actuator is working normally. |
| Error code: | M3-2130 |
| Display: | Output bin full Remove paper |
| Description: | Paper in output bin is full. Remove printed paper |
| Causes: | The machine detected that the output tray has got full or the bin-full sensor is defective. |
| Remedy: | 1) Remove the paper on the output tray. (The maximum loading capacity is 150 sheets based on standard paper (80 g/m²).) 2) Check if the Bin-full Sensor connector is connected properly. Reconnect it or replace the Bin-full sensor. |
| Error code: | S2-4120 |
| Display: | Door open. Close it. |
| Description: | Door open Close it |
| Causes: | Door is open or the cover open switch is defective. |
| Remedy: | 1) Check if the front cover is closed perfectly. 2) If the error persists, check that the cover-open sensor is working normally. If it is defective, replace the HVPS board. |
| Error code: | S6–3123 |
| Display: | Network Problem : IP Conflict |
| Description: | Network has some problem. (IP address conflicts with that of other system. / Communication error / There is no response when checking the ping test.) |
| Remedy: | Change the machine’s IP address. • Execute the Samsung Easy Printer Manager program. (Device setting - Network - IP address). Change the IP address. • In case of DHCP or Bootp, reboot the machine to receive a new IP address. |
| Error code: | S6–3128 |
| Display: | 802.1x Network Error. |
| Description: | The confirmation was requested for wired port, the server has rejected. / The confirmation protocol is not the same or user information (ID/Password) is wrong. |
| Remedy: | Check the setting-up for 802.1x confirmation server. • Re-enter the server information and confirmation protocol. • Re-enter the user information. |
| Error code: | U1–2315, U1–2320, U1–2330 |
| Display: | Error #U Turn off then on. |
| Description: | The temperature control of fuser unit is abnormal. |
| Remedy: | 1) Turn the machine off. Re-install the fuser unit. Then turn the machine on. Is the error message is disappeared? 2) If the problem persists, turn the machine off and remove the fuser unit. a) Check if the fuser connector is connected properly. b) Check if the input voltage is normal. c) Check if the thermistor is twisted or contaminated. 3) After confirming continuity in the fuser connector and the problem still exists; order an SMPS/HVPS and Fuser Unit and install as is necessary. • HVPS : JC44-00197A • SMPS : JC44-00095D (110V) / JC44-00096D (220V) • Fuser Unit : JC91-01023A (110V) / JC91-01024A (220V) |
| Error code: | U1–2334, U1–2340 |
| Display: | Error #U1-2330 Turn off then on Error #U1-2331 Turn off then on Error #U1-2333 Turn off then on Error #U1-2334 Turn off then on Error #U1-2340 Turn off then on |
| Description: | The temperature control of fuser unit is abnormal. (Low Heat Error or Over Heat Error) |
| Remedy: | 1) Turn the machine off. Re-install the fuser unit. Then turn the machine on. Is the error message is disappeared? 2) If the problem persists, turn the machine off and remove the fuser unit. a) Check if the fuser connector is connected properly. b) Check if the input voltage is normal. c) Check if the thermistor is twisted or contaminated. |
| Error code: | U2-1112, U2-1113 |
| Display: | LSU Unit Failure #U2-1112. Turn off then on. LSU Unit Failure #U2-1113. Turn off then on. |
| Description: | LSU Failure: #U2-111x. Turn off then on. Call for service if the problem persists |
| Causes: | LSU Motor does not work normally. / H Sync signal is abnormal. |
| Remedy: | 1) Execute the LSU motor test in EDC program. Check the LSU motor operation sound. 2) If there is no sound, remove the right cover. Check if the LSU harness on the main board is connected properly. 3) If it is OK, remove the top cover. Check if the LSU harness on LSU board is connected properly. (picture- 3,4) 4) Check if the LSU harness is defective. (picture- 5,6) 5) Reconnect the LSU harness and then execute the LSU motor test in EDC program again. 6) If the problem persists, replace the LSU. 7) If the problem persists after replacing LSU, replace the main board. |
