Samsung SCX-4116
Рейтинг
Модули
Fuser assembly
ADF ASSEMBLY
Middle Cover Assembly
OPE Unit Assembly(SCX-4216F)
Frame Assembly
Main assembly
RX Drive Assembly
OPE Unit Assembly(SCX-4116/4016)
ADF Assembly 2
Scanner assembly
CASSETTE ASSEMBLY
Детали RX Drive Assembly
| Деталь: | AS-FUSER 110V |
| Парткод: | JC81-01696A |
| Деталь: | COVER-M-FUSER |
| Парткод: | * |
| Деталь: | HOLDER-M-PLATE CLAW |
| Парткод: | * |
| Деталь: | SPRING ETC-CLAW |
| Парткод: | * |
| Деталь: | PMO-ROLLER EXIT |
| Парткод: | * |
| Деталь: | SPRING ETC-FUSER EXIT |
| Парткод: | * |
| Деталь: | THERMOSTAT-150 |
| Парткод: | JC47-00005A |
| Цена: | 500 ₽ |
| Деталь: | PMO-GEAR_EXIT_DRV16 |
| Парткод: | * |
| Деталь: | GEAR-IDLE 23 |
| Парткод: | * |
| Деталь: | Ring-CS |
| Парткод: | * |
| Деталь: | GEAR-RDCN 25/15 |
| Парткод: | JC66-00397A |
| Цена: | 270 ₽ |
| Деталь: | IPR-ELECTRODE_LAMP |
| Парткод: | * |
| Деталь: | ELECTRODE-WIRE_L |
| Парткод: | * |
| Деталь: | THERMISTOR-NTC |
| Парткод: | 1404-001298 |
| Цена: | 1 800 ₽ |
| Деталь: | ELECTRODE-WIRE_R |
| Парткод: | * |
| Деталь: | CBF HARNESS-FUSER 110V |
| Парткод: | JC39-00239A |
| Деталь: | GEAR-FUSER, Z37 |
| Парткод: | JC66-00564A |
| Цена: | 290 ₽ |
| Деталь: | BUSH-M-HR L |
| Парткод: | * |
| Деталь: | ROLLER-HEAT |
| Парткод: | JC66-00601A |
| Цена: | 1 700 ₽ |
| Деталь: | BUSH-M-HR R |
| Парткод: | JC61-00590A |
| Цена: | 250 ₽ |
| Деталь: | LAMP-HALOGEN |
| Парткод: | 4713-001182 |
| Деталь: | ROLLER-M-EXIT F/UP |
| Парткод: | * |
| Деталь: | Roller-Pressure |
| Парткод: | JC66-00600A |
| Деталь: | BEARING-PRESSURE/R |
| Парткод: | * |
| Деталь: | Spring-CS |
| Парткод: | * |
| Деталь: | PMO-BUSHING TX |
| Парткод: | * |
| Деталь: | HOLDER-ACTUATOR |
| Парткод: | * |
| Деталь: | PMO-ACTUATOR_EXIT |
| Парткод: | JC72-00987A |
| Цена: | 260 ₽ |
| Деталь: | IPR-P-FRAME_FUSER |
| Парткод: | * |
| Деталь: | GUIDE-M-INPUT |
| Парткод: | * |
| Деталь: | Spring-TS |
| Парткод: | * |
| Деталь: | RMO-RUBBER_EXIT |
| Парткод: | * |
| Деталь: | NUT-HEXAGON |
| Парткод: | * |
| Деталь: | LABEL(P)-CAUTION, HOT_FUSER |
| Парткод: | * |
| Деталь: | COVER-M-EXIT LOWER |
| Парткод: | * |
| Деталь: | PLATE-P-CLAW |
| Парткод: | * |
| Деталь: | ELA HOU-ADF |
| Парткод: | JC96-02654A |
| Деталь: | MEA UNIT-ADF UPPER |
| Парткод: | JC97-01710A |
| Деталь: | ELA HOU-ADF LOWER |
| Парткод: | JC81-01702A |
| Деталь: | ELA HOU-ADF MOTOR |
| Парткод: | JC81-01701A |
| Деталь: | MEAUNIT-COVER PLATEN |
| Парткод: | JC97-01708A |
| Деталь: | MEA UNIT-COVER OPEN(LEX) |
| Парткод: | JC97-01706A |
| Деталь: | MEA UNIT-PICKUP |
| Парткод: | JC97-01705A |
| Деталь: | COVER-M-ADF UPPER |
| Парткод: | JC63-00145A |
| Деталь: | ROLLER-M-ADF IDLE |
| Парткод: | JC66-00461A |
| Деталь: | MEA UNIT-HOLDER ADF |
| Парткод: | JC97-01709A |
| Цена: | 310 ₽ |
| Деталь: | COVER-M-ADF LOWER |
| Парткод: | JC63-00148A |
| Деталь: | PBA SUB-ADF |
| Парткод: | JC81-01717A |
| Деталь: | GROUND-P-ADF |
| Парткод: | JC63-00149A |
| Деталь: | SHAFT-M-FEED GEAR 38 |
| Парткод: | JC66-00460A |
| Деталь: | ROLLER-DRIVE |
| Парткод: | JC66-00560A |
| Цена: | 400 ₽ |
| Деталь: | PMO-ACTUATOR DOC SENSOR |
| Парткод: | JC72-01009A |
| Деталь: | PMO-ACTUATOR REGI SENSOR |
| Парткод: | JC72-01010A |
| Деталь: | PMO-ACTUATOR SCAN SENSOR |
| Парткод: | JC72-01011A |
| Деталь: | SPRING ETC-TORSION DOC (CC2-F) |
| Парткод: | JB61-00076A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | BRACKET-GEAR |
| Парткод: | JC61-00776A |
| Деталь: | MOTOR BLOWER-ADF |
| Парткод: | JC31-00023A |
| Деталь: | GEAR-CLUTCH 29 |
| Парткод: | JB66-00101A |
| Деталь: | PMO-WHITE CLUTCH SUB 29 |
| Парткод: | JB72-00844A |
| Деталь: | GEAR-CLUTCH 39 |
| Парткод: | JC66-00322A |
| Деталь: | Ring-C |
| Парткод: | 6044-000159 |
| Деталь: | GEAR-IDLE 35 ADF |
| Парткод: | JC66-00458A |
| Деталь: | GEAR-40/21 ADF |
| Парткод: | JC66-00456A |
| Деталь: | GEAR-SWING 31/20 ADF |
| Парткод: | JC66-00457A |
| Деталь: | COVER-M-PLATEN(4IN1) |
| Парткод: | JC63-00146A |
| Деталь: | Sheet-White Sponge |
| Парткод: | * |
| Деталь: | MEA-TX STACKER(SEC) |
| Парткод: | * |
| Деталь: | SPRING ETC-FEED |
| Парткод: | * |
| Деталь: | PMO-ROLL PINCH |
| Парткод: | JG72-40663A |
| Деталь: | SHAFT-STACKER |
| Парткод: | JC66-00594A |
| Деталь: | MEA UNIT-HINGE |
| Парткод: | JC97-01707A |
| Цена: | 350 ₽ |
| Деталь: | RPR-ROLLER EXIT IDLE |
| Парткод: | JC73-00091A |
| Деталь: | ICT-SHAFT PINCH |
| Парткод: | JF70-40521B |
| Деталь: | COVER-M-OPEN(LEX) |
| Парткод: | JC63-00147A |
| Деталь: | PMO-GUIDE PAPER |
| Парткод: | JB72-00843A |
| Деталь: | PMO-BUSHING WHITE |
| Парткод: | JF72-41306A |
| Деталь: | GEAR-ADF 38 |
| Парткод: | JB66-00103A |
| Цена: | 260 ₽ |
| Деталь: | IPR-GROUND_ROLLER |
| Парткод: | JC70-10467A |
| Деталь: | SHAFT-IDLE FEED |
| Парткод: | JC66-00558A |
| Деталь: | ROLLER-EXIT |
| Парткод: | JC66-00559A |
| Деталь: | MEC-Brush Antistatic |
| Парткод: | JC75-00161A |
| Деталь: | SHEET-WHITE BAR |
| Парткод: | JC63-00154A |
| Деталь: | PMO-BUSH |
| Парткод: | JB72-00819A |
| Деталь: | CBF HARNESS-ADR |
| Парткод: | JC39-00278A |
| Цена: | 950 ₽ |
| Деталь: | Gear-Agitator-2 |
| Парткод: | JC66-00310A |
| Деталь: | Ring-C |
| Парткод: | * |
| Деталь: | GUIDE-STACKER SUB |
| Парткод: | JC61-00712A |
| Деталь: | LINK-M-SWING ADF |
| Парткод: | JC66-00454A |
| Деталь: | GEAR-58/25 ADF |
| Парткод: | JC66-00455A |
| Деталь: | IMPELLER-ADF |
| Парткод: | JC66-00556A |
| Деталь: | GEAR-REMOVE ADF |
| Парткод: | JC66-00557A |
| Деталь: | Washer-Plain |
| Парткод: | 6031-000023 |
| Деталь: | IPR-WASHER WAVE |
| Парткод: | JB70-00070A |
| Деталь: | Washer-Plain |
| Парткод: | 6031-000019 |
| Деталь: | CBF HARNESS-MOTOR GND |
| Парткод: | JB39-00105A |
| Деталь: | Ring-E |
| Парткод: | 6044-000125 |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000269 |
| Деталь: | SPRING ETC PAD |
| Парткод: | JC61-00387A |
| Деталь: | RMO-ADF RUBBER |
| Парткод: | * |
| Деталь: | HOLDER-M-ADF |
| Парткод: | * |
| Деталь: | SPRING ETC-PAD |
| Парткод: | * |
| Деталь: | SHEET-ADF HOLDER |
| Парткод: | * |
| Деталь: | PMO-TX STACKER(SEC) |
| Парткод: | JB72-01166B |
| Деталь: | PMO-DOC GUIDE(L) |
| Парткод: | JB72-01171B |
| Деталь: | Gear-Pinion |
| Парткод: | JG66-40003A |
| Цена: | 260 ₽ |
| Деталь: | PMO-DOC GUIDE(R) |
| Парткод: | JB72-01170B |
| Деталь: | IPR-WASHER SPRING CU |
| Парткод: | JF70-10616A |
| Деталь: | MEA UNIT-COVER MIDDLE |
| Парткод: | JC97-01723A |
| Деталь: | COVER-M-MIDDLE |
| Парткод: | * |
| Деталь: | PMO-STACKER_RX(SEC) |
| Парткод: | * |
| Деталь: | Ring-CS |
| Парткод: | * |
| Деталь: | GEAR-IDLE 23 |
| Парткод: | * |
| Деталь: | PMO-GEAR_EXIT_DRV16 |
| Парткод: | * |
| Деталь: | GEAR-EXIT F/DOWN |
| Парткод: | * |
| Деталь: | MEC-BEARING,EXIT |
| Парткод: | JC75-10529A |
| Деталь: | Roller-Exit F/Down |
| Парткод: | * |
| Деталь: | RMO-RUBBER EXIT |
| Парткод: | * |
| Деталь: | PMO-BUSHING_F/DOWN |
| Парткод: | * |
| Деталь: | Spring-CS |
| Парткод: | * |
| Деталь: | HOLDER-M-EXIT F/DOWN |
| Парткод: | * |
| Деталь: | PMO-ROLLER_EXIT,MAIN |
| Парткод: | * |
| Деталь: | PMO-ROLLER_EXIT,FR |
| Парткод: | * |
| Деталь: | Washer-Plain |
| Парткод: | * |
| Деталь: | COVER-M-REAR UPPER |
| Парткод: | * |
| Деталь: | ROLLER-M_DECURL |
| Парткод: | * |
| Деталь: | ELAHOU-OPE |
| Парткод: | JC81-01695A |
| Деталь: | COVER-M-OPE(4IN1) |
| Парткод: | JC63-00153A |
| Деталь: | KEY-M-RESOLUTION |
| Парткод: | JC64-00059A |
| Деталь: | KEY-M-COPY |
| Парткод: | JC64-00054A |
| Деталь: | KEY-M-SCROLL |
| Парткод: | JC64-00056A |
| Деталь: | KEY-M-STOP |
| Парткод: | JC64-00055A |
| Деталь: | KEY-M-START |
| Парткод: | JC64-00057A |
| Деталь: | KEY-M-TEL |
| Парткод: | JC64-00053A |
| Деталь: | KEY-M-FAX |
| Парткод: | JC64-00060A |
| Деталь: | KEY-M-TONER SAVE |
| Парткод: | JC64-00058A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | KEY-M-TOLL SAVE |
| Парткод: | JC64-00061A |
| Деталь: | RUBBER-COPY |
| Парткод: | JC73-00139A |
| Деталь: | RUBBER-SCROLL |
| Парткод: | JC73-00137A |
| Деталь: | RUBBER-TEL/FAX |
| Парткод: | JC73-00138A |
| Деталь: | SHEET-LCD |
| Парткод: | JC63-00155A |
| Деталь: | PBASUB-OPE |
| Парткод: | JC81-01720A |
| Деталь: | ELAHOU-UNIT FRAME_110V |
| Парткод: | JC96-02731A |
| Деталь: | FRAME-M-BASE |
| Парткод: | JC61-00579A |
| Деталь: | GUIDE-P-TR |
| Парткод: | JC61-00607A |
| Деталь: | PLATE-P-SAW |
| Парткод: | JC61-00604A |
| Деталь: | GUIDE-M-TR RIB |
| Парткод: | JC61-00594A |
| Деталь: | PMO-GEAR_EXIT_DRV16 |
| Парткод: | * |
| Деталь: | Ring-CS |
| Парткод: | * |
| Деталь: | RMO-RUBBER_FOOT |
| Парткод: | * |
| Деталь: | IPR-P-GROUND_TR |
| Парткод: | * |
| Деталь: | MEC-TERMINAL |
| Парткод: | JC75-00049A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000119 |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | SCREW-ASSY TAPT |
| Парткод: | 6006-001078 |
| Деталь: | IPR-P-TERMINALCON |
| Парткод: | JC70-00312A |
| Деталь: | IPR-P-TERMINALCR |
| Парткод: | JC70-00313A |
| Деталь: | HOUSING-TERMINAL |
| Парткод: | JC61-00592A |
| Деталь: | PMO-LOCKER CST |
| Парткод: | JC72-00983A |
| Деталь: | PMO-ACTUATOR CVR OPEN |
| Парткод: | JC72-00974A |
| Деталь: | PMO-PLATE GUIDE DEVE_R |
| Парткод: | JC72-00985A |
| Цена: | 280 ₽ |
| Деталь: | Spring ETC-Guide Deve |
| Парткод: | * |
| Деталь: | IPR-P-GROUND_GUIDE PAPER |
| Парткод: | JC70-00458A |
| Деталь: | PMO-PLATE GUIDE DEVE_L |
| Парткод: | JC72-00984A |
| Цена: | 500 ₽ |
| Деталь: | PMO-ACTUATOR FEED |
| Парткод: | JC72-00976A |
| Цена: | 240 ₽ |
| Деталь: | PMO-Actuator Empty |
| Парткод: | JC72-00975A |
| Цена: | 290 ₽ |
| Деталь: | PMO-ACTUATOR MANUAL |
| Парткод: | JC72-00977A |
| Цена: | 290 ₽ |
| Деталь: | IPR-P-GROUND_EARTH TR |
| Парткод: | * |
| Деталь: | SPRING-ETC |
| Парткод: | 6107-001162 |
| Деталь: | ROLLER-FEED ROLLER 1 |
| Парткод: | * |
| Деталь: | PMO-Bushing Feed |
| Парткод: | * |
| Деталь: | Shaft-Feed |
| Парткод: | * |
| Деталь: | AS-PICK UP |
| Парткод: | JC81-01693A |
| Цена: | 400 ₽ |
| Деталь: | IPR-P-EARTH TRANSFER |
| Парткод: | JC70-00307A |
| Деталь: | HOLDER-PTL |
| Парткод: | JC61-00583A |
| Деталь: | LENS-PTL |
| Парткод: | JC67-00027A |
| Деталь: | BUSH-M-TR L |
| Парткод: | JC61-00588A |
| Деталь: | SPRING ETC-TR L HAWK |
| Парткод: | * |
| Деталь: | Roller-Feed |
| Парткод: | JC66-00598A |
| Цена: | 210 ₽ |
| Деталь: | PMO-BUSHING_TR(L) |
| Парткод: | JC72-00102A |
| Цена: | 30 ₽ |
| Деталь: | IPR-P-GROUND_FUSER |
| Парткод: | JC70-00310A |
| Деталь: | Shaft-Feed Idle |
| Парткод: | JC66-00527A |
| Цена: | 340 ₽ |
| Деталь: | BUSH-M-FEED IDLE |
| Парткод: | * |
| Деталь: | SPRING ETC-TR |
| Парткод: | * |
| Деталь: | IPR-P_GROUND_DRIVE2 |
| Парткод: | JC70-00335A |
| Деталь: | Spring-TS |
| Парткод: | 6107-001170 |
| Деталь: | CAM-M-PICK_UP |
| Парткод: | JC66-00377A |
| Цена: | 500 ₽ |
| Деталь: | IPR-P-GROUND_DRIVE |
| Парткод: | JC70-00308A |
| Деталь: | SOLENOID-HB (PICK-UP) |
| Парткод: | JC33-00009A |
| Цена: | 450 ₽ |
| Деталь: | SOLENOID-HB (MANUAL) |
| Парткод: | JC33-00010A |
| Цена: | 700 ₽ |
| Деталь: | AS-GEAR PICKJJP |
| Парткод: | JC81-01692A |
| Цена: | 270 ₽ |
| Деталь: | BRACKET-P-FEED |
| Парткод: | JC61-00602A |
| Деталь: | MEA UNIT-CLUTCH |
| Парткод: | JC97-01788A |
| Цена: | 650 ₽ |
| Деталь: | ELAHOJ-FJSER 110V, ROCKY |
| Парткод: | JC81-01696A |
| Деталь: | GUIDE-P-PAPER |
| Парткод: | JC61-00718A |
| Цена: | 330 ₽ |
| Деталь: | GEAR-FEED 2 |
| Парткод: | JC66-00394A |
| Деталь: | GEAR-IDLE 23 |
| Парткод: | JC66-00396A |
| Цена: | 300 ₽ |
| Деталь: | Spring-TS |
| Парткод: | * |
| Деталь: | IPR-P-TERMINAL DEVE KEY |
| Парткод: | * |
| Деталь: | CBF HARNESS-OPCjFJSE |
| Парткод: | * |
| Деталь: | PBAMAIN-PTL |
| Парткод: | JC92-01440B |
| Деталь: | BUSH-M-PICK_UP L |
| Парткод: | * |
| Деталь: | Shaft-P-Pick_up |
| Парткод: | * |
| Деталь: | STOPPER-PICK_UP |
| Парткод: | * |
| Деталь: | PMO-IDLE PICK_UP |
| Парткод: | JC72-00982A |
| Деталь: | SPONGE-ROLLER PICK_UP |
| Парткод: | JC72-01231A |
| Цена: | 150 ₽ |
| Деталь: | BUSH-M-PICK_UP R |
| Парткод: | JC61-00587A |
| Цена: | 280 ₽ |
| Деталь: | HOUSING-M-PICK_UP |
| Парткод: | JC61-00591A |
| Цена: | 240 ₽ |
| Деталь: | PMO-GEAR PICKjJP B |
| Парткод: | JC72-00980A |
| Деталь: | PMO-GEAR PICKjJP A |
| Парткод: | JC72-00979A |
| Цена: | 320 ₽ |
| Деталь: | Spring-CS |
| Парткод: | * |
| Деталь: | GEAR-FEED 1 |
| Парткод: | JC66-00393A |
| Цена: | 190 ₽ |
| Деталь: | PMO-COLLARjSPRING |
| Парткод: | JC72-00978A |
| Деталь: | PMO-HUB CLUTCH |
| Парткод: | JC72-00981A |
| Деталь: | SCX-4216F / SCX-4116 / SCX-4016 |
| Парткод: | P400238564 |
| Деталь: | ELAHOU-UNIT SCAN |
| Парткод: | JC96-02669A |
| Деталь: | ELA HOU-UNIT SCAN(4116) |
| Парткод: | JC96-02790A |
| Деталь: | ELAHOU-UNIT SCAN |
| Парткод: | JC96-02788A |
| Деталь: | ELAHOU-UNIT FRAME_110V |
| Парткод: | JC96-02731A |
| Деталь: | ELAUNIT-RX DRIVE |
| Парткод: | JC96-02733A |
| Цена: | 2 700 ₽ |
| Деталь: | UNIT-HUMMINGBIRD LSU |
| Парткод: | JC59-00018A |
| Цена: | 3 700 ₽ |
| Деталь: | CBF HARNESS-LSU |
| Парткод: | JC39-00242A |
| Деталь: | SMPS-SMPS(V1)+HVPS |
| Парткод: | JC44-00044A |
| Деталь: | PBA MAIN-MAIN |
| Парткод: | JC92-01431A |
| Цена: | 6 300 ₽ |
| Деталь: | PBA MAIN-COPIER |
| Парткод: | JC92-01463A |
| Деталь: | MEA UNIT-COVER MIDDLE |
| Парткод: | JC97-01723A |
| Деталь: | MEA UNIT-COVER FRONT(SEC) |
| Парткод: | JC97-01746F |
| Деталь: | MEA UNIT-CASSETTE, USA |
| Парткод: | JC97-01750A |
| Цена: | 1 700 ₽ |
| Деталь: | ELAHOU-COVER SIDE L |
| Парткод: | JC96-02709A |
| Деталь: | COVER-M-SIDE L |
| Парткод: | JC63-00137A |
| Деталь: | COVER-M-SIDE R |
| Парткод: | JC63-00138A |
| Деталь: | MEA Unit-Cover Rear |
| Парткод: | JC97-01724D |
| Деталь: | FAN-DC_HUMMINGBIRD |
| Парткод: | JC31-00027A |
| Цена: | 900 ₽ |
| Деталь: | CBF Harness-Motor |
| Парткод: | JC39-00241A |
| Деталь: | MEAETC-TR |
| Парткод: | JC97-01793A |
| Деталь: | CBF SIGNAL-LIU |
| Парткод: | JC39-00270A |
| Деталь: | PBA SUB-LIU_USA_EXT |
| Парткод: | JC92-01481C |
| Деталь: | ELA-TONER UNIT |
| Парткод: | * |
| Деталь: | PLATE-P-CHANNEL |
| Парткод: | JC61-00606A |
| Деталь: | PBA SUB-CONN |
| Парткод: | JC81-01718A |
| Деталь: | CBF HARNESS-ENGINE |
| Парткод: | JC39-00240B |
| Деталь: | BRACKET-P-INLET, ROCKY |
| Парткод: | JC61-00693A |
| Деталь: | MEA UNIT-SHIELD ENGINE |
| Парткод: | JC97-01794A |
| Деталь: | CBF HARNESS-SCAN |
| Парткод: | JC39-00268A |
| Деталь: | SUPPORTER |
| Парткод: | 6103-001048 |
| Деталь: | CBF-HARNESS-DUPLEX GND |
| Парткод: | JC39-00090A |
| Деталь: | COVER-LCD WINDOW |
| Парткод: | JC63-00251A |
| Деталь: | ELA HOU-ADF |
| Парткод: | JC81-01700A |
| Деталь: | ELAHOU-OPE |
| Парткод: | JC81-01695A |
| Деталь: | ELAHOU-OPE(3IN1) |
| Парткод: | JC81-01697A |
| Деталь: | ELAHOU-OPE(3IN1) |
| Парткод: | JC81-01698A |
| Деталь: | ELAHOU-PLATEN |
| Парткод: | JC81-01703A |
| Деталь: | ADJUST-M-MANUAL_R |
| Парткод: | * |
| Деталь: | ADJUST RACK-M-MANUAL |
| Парткод: | * |
| Деталь: | COVER-M_FRONT(ROCKY) |
| Парткод: | * |
| Деталь: | ADJUST-M-MANUAL_L |
| Парткод: | * |
| Деталь: | Gear-Rack_Pinion |
| Парткод: | * |
| Деталь: | COVER-M-SIDE L |
| Парткод: | * |
| Деталь: | SPEAKER |
| Парткод: | * |
| Деталь: | Screw-Taptite |
| Парткод: | * |
| Деталь: | COVER-M-REAR |
| Парткод: | JC63-00140D |
| Деталь: | COVER-M-FACE UP |
| Парткод: | JC63-00142A |
| Деталь: | ROLLER-TRANSFER ROLLER |
| Парткод: | JC66-00528A |
| Цена: | 750 ₽ |
| Деталь: | GEAR-TRANSFER |
| Парткод: | JC66-00395A |
| Цена: | 260 ₽ |
| Деталь: | PPR-SPACER_TR |
| Парткод: | JC72-00851A |
| Деталь: | SHIELD-ENGINE, ROCKY |
| Парткод: | JC63-00144A |
| Деталь: | SUPPORTER |
| Парткод: | 6103-001056 |
| Деталь: | ELAUNIT-RX DRIVE |
| Парткод: | JC96-02733A |
| Цена: | 2 700 ₽ |
| Деталь: | BRACKET-P-GEAR 1400 |
| Парткод: | * |
| Деталь: | GEAR-RDCN 53/26 |
| Парткод: | JC66-00388A |
| Деталь: | GEAR-RDCN 113/33 |
| Парткод: | JC66-00391A |
| Деталь: | GEAR-RDCN 57/18 |
| Парткод: | JC66-00389A |
| Цена: | 260 ₽ |
| Деталь: | Washer-Plain |
| Парткод: | * |
| Деталь: | BRACKET-P-MOTOR 1400 |
| Парткод: | * |
| Деталь: | GEAR-RDCN 103/41 |
| Парткод: | JC66-00390A |
| Цена: | 270 ₽ |
| Деталь: | GEAR-RDCN 90/31 |
| Парткод: | JC66-00392A |
| Цена: | 270 ₽ |
| Деталь: | MOTOR STEP-HUMMINGBIRD |
| Парткод: | JC31-00028A |
| Деталь: | PMO-IMPELLER_DRV |
| Парткод: | * |
| Деталь: | ELAHOU-OPE(3IN1) |
| Парткод: | JC81-01697A |
| Деталь: | ELAHOU-OPE(3IN1) |
| Парткод: | JC81-01698A |
| Деталь: | COVER-M-OPE(3IN1) |
| Парткод: | JC63-00135A |
| Деталь: | KEY-M-RESOLUTION(3IN1) |
| Парткод: | JC64-00051A |
| Деталь: | KEY-M-COPY(3IN1) |
| Парткод: | JC64-00050A |
| Деталь: | KEY-M-SCROLL |
| Парткод: | JC64-00056A |
| Деталь: | KEY-M-STOP |
| Парткод: | JC64-00055A |
| Деталь: | KEY-M-START(3IN1) |
| Парткод: | JC64-00057B |
| Деталь: | KEY-M-TONER SAVE(3IN1) |
| Парткод: | JC64-00052A |
| Деталь: | RUBBER-COPY(3IN1) |
| Парткод: | JC73-00136A |
| Деталь: | RUBBER-SCROLL |
| Парткод: | JC73-00137A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | SHEET-LCD(4116) |
| Парткод: | JC63-00155D |
| Деталь: | SHEET-LCD(3IN1) |
| Парткод: | JC63-00155B |
| Деталь: | PBASUB-OPE |
| Парткод: | JC81-01716A |
| Деталь: | RUBBER-IMAGE(3IN1) |
| Парткод: | JC73-00135A |
| Деталь: | ELA HOU-ADF |
| Парткод: | JC96-02654A |
| Деталь: | MEA UNIT-ADF UPPER |
| Парткод: | JC97-01710A |
| Деталь: | ELA HOU-ADF LOWER |
| Парткод: | JC81-01702A |
| Деталь: | ELA HOU-ADF MOTOR |
| Парткод: | JC81-01701A |
| Деталь: | MEAUNIT-COVER PLATEN |
| Парткод: | JC97-01708A |
| Деталь: | MEA UNIT-COVER OPEN(LEX) |
| Парткод: | JC97-01706A |
| Деталь: | MEA UNIT-PICKUP |
| Парткод: | JC97-01705A |
| Деталь: | COVER-M-ADF UPPER |
| Парткод: | JC63-00145A |
| Деталь: | ROLLER-M-ADF IDLE |
| Парткод: | JC66-00461A |
| Деталь: | MEA UNIT-HOLDER ADF |
| Парткод: | JC97-01709A |
| Цена: | 310 ₽ |
| Деталь: | COVER-M-ADF LOWER |
| Парткод: | JC63-00148A |
| Деталь: | PBA SUB-ADF |
| Парткод: | JC81-01717A |
| Деталь: | GROUND-P-ADF |
| Парткод: | JC63-00149A |
| Деталь: | SHAFT-M-FEED GEAR 38 |
| Парткод: | JC66-00460A |
| Деталь: | ROLLER-DRIVE |
| Парткод: | JC66-00560A |
| Цена: | 400 ₽ |
| Деталь: | PMO-ACTUATOR DOC SENSOR |
| Парткод: | JC72-01009A |
| Деталь: | PMO-ACTUATOR REGI SENSOR |
| Парткод: | JC72-01010A |
| Деталь: | PMO-ACTUATOR SCAN SENSOR |
| Парткод: | JC72-01011A |
| Деталь: | SPRING ETC-TORSION DOC (CC2-F) |
| Парткод: | JB61-00076A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | BRACKET-GEAR |
| Парткод: | JC61-00776A |
| Деталь: | MOTOR BLOWER-ADF |
| Парткод: | JC31-00023A |
| Деталь: | GEAR-CLUTCH 29 |
| Парткод: | JB66-00101A |
| Деталь: | PMO-WHITE CLUTCH SUB 29 |
| Парткод: | JB72-00844A |
| Деталь: | GEAR-CLUTCH 39 |
| Парткод: | JC66-00322A |
| Деталь: | Ring-C |
| Парткод: | 6044-000159 |
| Деталь: | GEAR-IDLE 35 ADF |
| Парткод: | JC66-00458A |
| Деталь: | GEAR-40/21 ADF |
| Парткод: | JC66-00456A |
| Деталь: | GEAR-SWING 31/20 ADF |
| Парткод: | JC66-00457A |
| Деталь: | COVER-M-PLATEN(4IN1) |
| Парткод: | JC63-00146A |
| Деталь: | Sheet-White Sponge |
| Парткод: | * |
| Деталь: | MEA-TX STACKER(SEC) |
| Парткод: | * |
| Деталь: | SPRING ETC-FEED |
| Парткод: | * |
| Деталь: | PMO-ROLL PINCH |
| Парткод: | JG72-40663A |
| Деталь: | SHAFT-STACKER |
| Парткод: | JC66-00594A |
| Деталь: | MEA UNIT-HINGE |
| Парткод: | JC97-01707A |
| Цена: | 350 ₽ |
| Деталь: | RPR-ROLLER EXIT IDLE |
| Парткод: | JC73-00091A |
| Деталь: | ICT-SHAFT PINCH |
| Парткод: | JF70-40521B |
| Деталь: | COVER-M-OPEN(LEX) |
| Парткод: | JC63-00147A |
| Деталь: | PMO-GUIDE PAPER |
| Парткод: | JB72-00843A |
| Деталь: | PMO-BUSHING WHITE |
| Парткод: | JF72-41306A |
| Деталь: | GEAR-ADF 38 |
| Парткод: | JB66-00103A |
| Цена: | 260 ₽ |
| Деталь: | IPR-GROUND_ROLLER |
| Парткод: | JC70-10467A |
| Деталь: | SHAFT-IDLE FEED |
| Парткод: | JC66-00558A |
| Деталь: | ROLLER-EXIT |
| Парткод: | JC66-00559A |
| Деталь: | MEC-Brush Antistatic |
| Парткод: | JC75-00161A |
| Деталь: | SHEET-WHITE BAR |
| Парткод: | JC63-00154A |
| Деталь: | PMO-BUSH |
| Парткод: | JB72-00819A |
| Деталь: | CBF HARNESS-ADR |
| Парткод: | JC39-00278A |
| Цена: | 950 ₽ |
| Деталь: | Gear-Agitator-2 |
| Парткод: | JC66-00310A |
| Деталь: | Ring-C |
| Парткод: | * |
| Деталь: | GUIDE-STACKER SUB |
| Парткод: | JC61-00712A |
| Деталь: | LINK-M-SWING ADF |
| Парткод: | JC66-00454A |
| Деталь: | GEAR-58/25 ADF |
| Парткод: | JC66-00455A |
| Деталь: | IMPELLER-ADF |
| Парткод: | JC66-00556A |
| Деталь: | GEAR-REMOVE ADF |
| Парткод: | JC66-00557A |
| Деталь: | Washer-Plain |
| Парткод: | 6031-000023 |
| Деталь: | IPR-WASHER WAVE |
| Парткод: | JB70-00070A |
| Деталь: | Washer-Plain |
| Парткод: | 6031-000019 |
| Деталь: | CBF HARNESS-MOTOR GND |
| Парткод: | JB39-00105A |
| Деталь: | Ring-E |
| Парткод: | 6044-000125 |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000269 |
| Деталь: | SPRING ETC PAD |
| Парткод: | JC61-00387A |
| Деталь: | RMO-ADF RUBBER |
| Парткод: | * |
| Деталь: | HOLDER-M-ADF |
| Парткод: | * |
| Деталь: | SPRING ETC-PAD |
| Парткод: | * |
| Деталь: | SHEET-ADF HOLDER |
| Парткод: | * |
| Деталь: | PMO-TX STACKER(SEC) |
| Парткод: | JB72-01166B |
| Деталь: | PMO-DOC GUIDE(L) |
| Парткод: | JB72-01171B |
| Деталь: | Gear-Pinion |
| Парткод: | JG66-40003A |
| Цена: | 260 ₽ |
| Деталь: | PMO-DOC GUIDE(R) |
| Парткод: | JB72-01170B |
| Деталь: | IPR-WASHER SPRING CU |
| Парткод: | JF70-10616A |
| Деталь: | ELAHOU-PLATEN |
| Парткод: | JC81-01703A |
| Деталь: | MEA UNIT-SCAN UPPER |
| Парткод: | JC97-01712A |
| Деталь: | ELAHOU-SCAN LOWER |
| Парткод: | JC81-01704A |
| Деталь: | COVER-M-SCAN UPPER |
| Парткод: | JC63-00151A |
| Деталь: | GLASS-SCAN |
| Парткод: | JC01-00001A |
| Деталь: | MEA UNIT-SCAN DUMMY |
| Парткод: | JC97-01711A |
| Деталь: | COVER-M-SCAN LOWER |
| Парткод: | JC63-00150A |
| Деталь: | ELA HOU-CCD MODULE |
| Парткод: | JC96-02821A |
| Деталь: | CBF SIGNAL-CCD FFC |
| Парткод: | JC39-00269A |
| Деталь: | ELA UNIT-CORE |
| Парткод: | 3301-001413 |
| Деталь: | ICT-SHAFT CCD |
| Парткод: | JB70-00145A |
| Деталь: | PMO-HOLDER BELT |
| Парткод: | JB72-00764A |
| Деталь: | PMO-PULLEY |
| Парткод: | JB72-00763A |
| Деталь: | PMO-HOLDER BELT |
| Парткод: | JB72-01136A |
| Деталь: | SPRING ETC-BELT |
| Парткод: | JB61-00109A |
| Деталь: | Spring-CS |
| Парткод: | 6107-001135 |
| Деталь: | PMO-LEVER SENSOR |
| Парткод: | JC72-00755A |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | 0604-001095 |
| Деталь: | CBF HARNESS-OPE/FLAT_COVER |
| Парткод: | JC39-00267A |
| Деталь: | Belt-Timing Gear |
| Парткод: | 6602-001067 |
| Цена: | 420 ₽ |
| Деталь: | ELAHOU-SCAN MOTOR |
| Парткод: | JC81-01705A |
| Цена: | 1 900 ₽ |
| Деталь: | DUMPER-CCD |
| Парткод: | JC66-00665A |
| Деталь: | COVER-M-SCAN DUMMY(4IN1) |
| Парткод: | * |
| Деталь: | MCT-GLASS ADF |
| Парткод: | * |
| Деталь: | TAPE-DOUBLE FACE |
| Парткод: | * |
| Деталь: | LABEL(P)-SHADING |
| Парткод: | * |
| Деталь: | BRACKET-M-SCAN MOTOR |
| Парткод: | * |
| Деталь: | MOTOR STEP-SCAN |
| Парткод: | JB31-00011A |
| Цена: | 1 300 ₽ |
| Деталь: | GEAR-REDUCTION |
| Парткод: | * |
| Деталь: | GEAR-IDLE |
| Парткод: | * |
| Деталь: | GEAR-TIMING |
| Парткод: | * |
| Деталь: | PMO-HOLDER BELT |
| Парткод: | * |
| Деталь: | Ring-E |
| Парткод: | * |
| Деталь: | MEA UNIT-CASSETTE, USA |
| Парткод: | JC97-01750A |
| Цена: | 1 700 ₽ |
| Деталь: | FRAME-M_CASSETTE |
| Парткод: | * |
| Деталь: | PMO-EXTENSION LARGE |
| Парткод: | JC72-00970A |
| Деталь: | PMO-EXTENSION SMALL |
| Парткод: | JC72-00971A |
| Деталь: | PLATE-P-KNOCKJJP |
| Парткод: | * |
| Деталь: | Spring-CS |
| Парткод: | * |
| Деталь: | Holder-M-Pad |
| Парткод: | * |
| Деталь: | Spring Etc-Exit Roll FD |
| Парткод: | * |
| Деталь: | ROLLER-M-IDLE FEED |
| Парткод: | * |
| Деталь: | Spring-ES |
| Парткод: | * |
| Деталь: | PMO-PLATEjLOCKER |
| Парткод: | * |
| Деталь: | Spring Etc-Locker,Plate |
| Парткод: | * |
| Деталь: | ADJJST-M-CASSETTEjL |
| Парткод: | JC70-00300A |
| Деталь: | ADJJST-M-CASSETTEjR |
| Парткод: | JC70-00301A |
| Деталь: | Gear-Pinion |
| Парткод: | * |
| Деталь: | INDICATOR-M-LEVER INDICATOR |
| Парткод: | JC64-00040A |
| Деталь: | RPR-FRICTION PAD |
| Парткод: | JC73-00140A |
| Цена: | 90 ₽ |
| Деталь: | IPR-Plate Pad |
| Парткод: | * |
| Деталь: | RPR-Pad Cassette |
| Парткод: | * |
Коды ошибок
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Описание
| Error code: | 01 |
| Display: | ERROR CONDITION INVALID HEAD |
| Description: | The ERROR light flashes. |
| Causes: | The printhead was replaced with one that is not a genuine Zebra™ printhead. |
| Remedy: | Install a genuine Zebra printhead. |
| Error code: | 02 |
| Display: | ERROR CONDITION RIBBON OUT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | In thermal transfer mode, ribbon is not loaded or incorrectly loaded. In thermal transfer mode, the ribbon sensor is not detecting ribbon that is loaded incorrectly. In thermal transfer mode, media is blocking the ribbon sensor. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly. |
| Remedy: | Load ribbon correctly. 1. Load ribbon correctly. See Load Ribbon on page 64. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Load media correctly. See Load Media on page 58. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Print a sensor profile. See Print Sensor Profile on page 89. The ribbon out threshold (marked by the word RIBBON) is likely too high, above the black area that indicates where the ribbon is detected. 2. Calibrate the sensors or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73. |
| Error code: | 03 |
| Display: | WARNING RIBBON IN |
| Description: | The ERROR light flashes. |
| Causes: | Ribbon is loaded, but the printer is set for direct thermal mode. |
| Remedy: | Ribbon is not required with direct thermal media. If you are using direct thermal media, remove the ribbon. This error message will not affect printing. If you are using thermal transfer media, which requires ribbon, set the printer for Thermal Transfer mode. See Select Print Method on page 81. |
| Error code: | 04 |
| Display: | ERROR CONDITION PAPER OUT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded. |
| Remedy: | Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration. |
| Error code: | 05 |
| Display: | ERROR CONDITION HEAD OPEN |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The printhead is not fully closed. The head open sensor is not working properly. |
| Remedy: | Replace the sensor. |
| Error code: | 06 |
| Display: | THERMISTOR FAULT |
| Description: | The ERROR light flashes. |
| Causes: | The printhead has a faulty thermistor. |
| Remedy: | Replace the printhead. |
| Error code: | 07 |
| Display: | WARNING HEAD COLD, THERMISTOR FAULT, ERROR CONDITION HEAD ELEMENT BAD |
| Description: | The printer stops; the ERROR light is on; the printer cycles through these three messages. |
| Causes: | The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
| Remedy: | Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
| Error code: | 08 |
| Display: | WARNING HEAD COLD |
| Description: | The printer prints while the ERROR light flashes. |
| Causes: | The printhead temperature is approaching its lower operating limit. The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
| Remedy: | Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the printer to a warmer area. Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
| Error code: | 09 |
| Display: | WARNING HEAD TOO HOT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The printhead is over temperature. |
| Remedy: | Allow the printer to cool. Printing automatically resumes when the printhead elements cool to an acceptable operating temperature. |
| Error code: | 10 |
| Display: | DEFRAGMENTING |
| Description: | The printer stops. |
| Causes: | The printer is defragmenting memory. |
| Remedy: | Caution • Do NOT turn off the printer power during defragmenting. Doing so can damage the printer. Allow the printer to finish defragmenting. If you get this error message frequently, check your label formats. Formats that write to and erase memory frequently may cause the printer to defragment often. Using properly coded label formats usually minimizes the need for defragmenting. If this error message does not go away, contact Technical Support. The printer requires service. |
| Error code: | 11 |
| Display: | ERROR CONDITION CUTTER JAM |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | Caution • The cutter blade is sharp. Do not touch or rub the blade with your fingers. The cutter blade is in the media path. |
| Remedy: | Turn off the printer power and unplug the printer. Inspect the cutter module for debris and clean as needed following the cleaning instructions in Clean the Cutter Module on page 135. |
| Error code: | 12 |
| Description: | General print quality issues |
| Causes: | The printer is set at the incorrect print speed. You are using an incorrect combination of labels and ribbon for your application. The printer is set at an incorrect darkness level. The printhead is dirty. Incorrect or uneven printhead pressure. The printhead is improperly balanced. |
| Remedy: | For optimal print quality, set the print speed to the lowest possible setting for your application via control panel, the driver, or the software. See Adjust Print Speed on page 79. You may want to perform the FEED Self Test on page 120. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. For optimal print quality, set the darkness to the lowest possible setting for your application via the control panel, the driver, or the software. See Adjust Print Darkness on page 78. You may want to perform the FEED Self Test on page 120 to determine the ideal darkness setting. Clean the printhead. See Clean the Printhead and Platen Roller on page 131. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Adjust the printhead balance. |
| Error code: | 13 |
| Description: | Long tracks of missing print on several labels |
| Causes: | Print element damaged. |
| Remedy: | Replace the printhead. |
| Error code: | 14 |
| Description: | Wrinkled ribbon |
| Causes: | Ribbon fed through the machine incorrectly. Incorrect burn temperature. Incorrect or uneven printhead pressure. Media not feeding properly; walking from side to side. The strip plate needs adjusting. The printhead needs vertical adjustment. The printhead is improperly balanced. The printhead and platen roller need to be realigned. |
| Remedy: | See Load Ribbon on page 64. Set the darkness to the lowest possible setting for good print quality. See Adjust Print Darkness on page 78. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Make sure that media is snug by adjusting the media guide, or call a service technician. Adjust the printhead balance. |
| Error code: | 15 |
| Description: | Printing too light or too dark over the entire label |
| Causes: | The media or ribbon is not designed for high-speed operation. You are using an incorrect combination of media and ribbon for your application. You are using ribbon with direct thermal media. Incorrect or uneven printhead pressure. |
| Remedy: | Replace supplies with those recommended for high-speed operation. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. Direct thermal media does not require ribbon. To check if you are using direct thermal media, perform the label scratch test in When to Use Ribbon on page 62. Set the pressure to the minimum needed. See Adjust Printhead Pressure on page 70. |
| Error code: | 16 |
| Description: | Smudge marks on labels |
| Causes: | The media or ribbon is not designed for high-speed operation. |
| Remedy: | Replace supplies with those recommended for high-speed operation. |
| Error code: | 17 |
| Description: | Misregistration/skips labels |
| Causes: | The printer is not calibrated. Improper label format. |
| Remedy: | Recalibrate the printer. Use correct label format. |
| Error code: | 18 |
| Description: | Misregistration and misprint of one to three labels |
| Causes: | The platen roller is dirty. Media does not meet specifications. |
| Remedy: | See Clean the Printhead and Platen Roller on page 131. Use media that meets specifications. |
| Error code: | 19 |
| Description: | Vertical drift in top-of-form position |
| Causes: | The printer is out of calibration. Vertical drift occurs during normal printer operation. Note • A vertical drift of ± 4 to 6 dot rows (approximately 0.5 mm) is within normal tolerances. The platen roller is dirty. |
| Remedy: | Recalibrate the printer. Calibrate the printer. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. |
| Error code: | 20 |
| Description: | Vertical image or label drift |
| Causes: | The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media. |
| Remedy: | Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation. |
| Error code: | 21 |
| Description: | The bar code printed on a label does not scan. |
| Causes: | The bar code is not within specifications because the print is too light or too dark. Not enough blank space around the bar code. |
| Remedy: | Perform the FEED Self Test on page 120. Adjust the darkness or print speed settings as necessary. Leave at least 1/8 in. (3.2 mm) between the bar code and other printed areas on the label and between the bar code and the edge of the label. |
| Error code: | 22 |
| Description: | Loss of printing registration on labels. Excessive vertical drift in top-of-form registration. |
| Causes: | The platen roller is dirty. Media guides are positioned improperly. The media type is set incorrectly. The media is loaded incorrectly. |
| Remedy: | Clean the platen roller according to the instructions in Clean the Printhead and Platen Roller on page 131. Ensure that the media guides are properly positioned. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. Load media correctly. See Load Media on page 58. |
| Error code: | 23 |
| Description: | Auto Calibrate failed. |
| Causes: | Media or ribbon is loaded incorrectly. The sensors could not detect the media or ribbon. The sensors are dirty or positioned improperly. The sensors are dirty, or media is positioned improperly for the sensors to detect. The media type is set incorrectly. |
| Remedy: | Ensure that media and ribbon are loaded correctly. Manually calibrate the printer. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Ensure that the sensors are clean and that media is positioned properly. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. |
| Error code: | 24 |
| Description: | A label format was sent to the printer but was not recognized. The DATA light does not flash. |
| Causes: | The communication parameters are incorrect. |
| Remedy: | Check the printer driver or software communications settings (if applicable). If you are using serial communication, check the serial port setting in the control panel menu. See Set Serial Communications on page 91. If you are using serial communication, make sure you are using a null modem cable or a null modem adapter. Using the control panel controls, check the protocol setting. It should be set to NONE. See Set Protocol on page 93. If a driver is used, check the driver communication settings for your connection. |
| Error code: | 25 |
| Description: | A label format was sent to the printer. Several labels print, then the printer skips, misplaces, misses, or distorts the image on the label. |
| Causes: | The serial communication settings are incorrect. |
| Remedy: | Ensure that the flow control settings match. Check the communication cable length. See Table 5 on page 48 for requirements. Check the printer driver or software communications settings (if applicable). |
| Error code: | 26 |
| Description: | A label format was sent to the printer but was not recognized. The DATA light flashes but no printing occurs. |
| Causes: | The prefix and delimiter characters set in the printer do not match the ones in the label format. Incorrect data is being sent to the printer. |
| Remedy: | Verify the prefix and delimiter characters. See Set Format Prefix Character on page 94 and Set Delimiter Character on page 95 for the requirements. Check the communication settings on the computer. Ensure that they match the printer settings. If the problem continues, check the label format. |
| Error code: | 27 |
| Description: | Broken or melted ribbon |
| Causes: | Darkness setting too high. |
| Remedy: | 1. Reduce the darkness setting. 2. Clean the printhead thoroughly. |
| Error code: | 28 |
| Description: | The printer does not detect when the ribbon runs out. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly. |
| Causes: | The ribbon-out threshold is set too high to detect the ribbon. On a sensor profile, the ribbon-out threshold (circled in Figure 15) appears above the black bars that indicate the ribbon. This happens if you calibrate the printer without ribbon and later insert ribbon without recalibrating the printer or loading printer defaults. |
| Remedy: | 1. Print a sensor profile (see Print Sensor Profile on page 89), and note the location of the ribbon-out threshold (circled in Figure 15). 2. Calibrate the printer, this time using ribbon, or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73. Important • Loading defaults resets all printer parameters back to factory defaults. 3. Print another sensor profile, and compare it to the first one. 4. If the ribbon-out threshold is still too high, you may manually change the value. |
| Error code: | 29 |
| Description: | The ribbon light is on even though ribbon is loaded correctly. |
| Causes: | The printer was not calibrated for the label and ribbon being used. |
| Remedy: | Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. |
| Error code: | 30 |
| Description: | The LCD displays a language that I cannot read |
| Causes: | The language parameter was changed through the control panel or a firmware command. |
| Remedy: | 1. Press SETUP/EXIT to enter configuration mode. 2. Press MINUS (-). The printer displays the LANGUAGE parameter in the current language. Even if you cannot recognize the characters displayed, you can still scroll to another language. 3. Press SELECT to select the parameter. 4. Press PLUS (+) or MINUS (-) to scroll through the choices until you find a language that you can read. 5. Press SETUP/EXIT. The LCD displays SAVE CHANGES in the original language. 6. Press SETUP/EXIT again to exit configuration mode and save the changes (if the language does not change, you may need to scroll to a different save option by pressing PLUS (+) or MINUS (-) in the previous step). 7. Repeat this process, if necessary, until you reach the desired language. |
| Error code: | 31 |
| Description: | The LCD is missing characters or parts of characters |
| Causes: | The LCD may need replacing. |
| Remedy: | Run the Power-On Self Test on page 117 and check that the LCD display shows all characters. If not, replace the LCD. |
| Error code: | 32 |
| Description: | Changes in parameter settings did not take effect |
| Causes: | Parameters are set incorrectly. A command turned off the ability to change the parameter. A command changed the parameter back to the previous setting. If the problem continues, there may be a problem with the main logic board. |
| Remedy: | 1. Set parameters and save permanently. 2. Turn the printer off (O) and then on (I). Refer to the ZPL Programming Guide. Refer to the ZPL Programming Guide. Replace the main logic board. |
Название
Samsung Тонер-картридж черный
Samsung Двойная упаковка тонер-картриджа SCX-4216D3
