Toshiba DP-1640

Рейтинг

Парткаталог
Коды ошибок

Модули

DEVELOPER-ASY

BYPASS-FEEDER-ASY

STAY-ASY

REPLACE UNIT

SUPPLIES

FUSER-2-ASY

COVER-1-ASY

OPTICAL-DRIVE-ASY

TRANSPORT-CHARGER-ASY

ALIGNING-ASY

PLATEN-ASY

FUSER-1-ASY

OPTICAL-FRAME-ASY

COVER-3-ASY

RECYCLE-ASY

BYPASS-ASY

FRONT-FRAME-ASY

COVER-2-ASY

DRAWER-ASY

BASE-FRAME-ASY

PM-KIT

CONTROL-PANEL-ASY

CLEANER-ASY

MAIN-CHARGER-ASY

MAIN-DRIVE-ASY

COVER-GUIDE-ASY

REAR-FRAME-ASY

GUIDE-ALIGNING-ASY

Детали MAIN-CHARGER-ASY

Деталь:	CASE-CH-M
Парткод:	6LA84920000

Деталь:	CH-M
Парткод:	6LA84925000

Деталь:	GRID-CH-M-371
Парткод:	6LA84930000

Деталь:	HANGER-WIRE-TR
Парткод:	4401764730

Деталь:	LID-CH-M-F
Парткод:	6LA84944000

Деталь:	LID-CH-M-R
Парткод:	6LA84947000

Деталь:	MYLAR-CLN-CH
Парткод:	6LA84941000

Деталь:	MYLAR-LED
Парткод:	6LA84957000

Деталь:	ROD-CLN-CH-M
Парткод:	6LA84938000

Деталь:	S/TPP/FH/FEXM-3X8-NI
Парткод:	X0-02247000

Деталь:	SPE-GR
Парткод:	6LA84950000

Деталь:	SPL-CH-M-R
Парткод:	6LA84922000

Деталь:	SPRING-TENS-CH
Парткод:	6LA84935000

Деталь:	TERM-CH-M-R
Парткод:	6LA84915000

Деталь:	TERM-CH-M-F
Парткод:	6LA84910000

Деталь:	ASY-CH-MAIN
Парткод:	6LA84902000

Коды ошибок

C01

C21

C26

C41

C43

C44

C45

C55

C94

C97

CA1

CA2

E01

E02

E03

E09

E12

E13

E14

E21

E40

E41

E44

E71

E72

E73

E86

E87

F14

Деталь:	2X10-SS S/TPP/BID-3*8-NI
Парткод:	X0-00980000

Деталь:	ASYS-GLASS-PLATEN-280-L
Парткод:	6LE60740100

Деталь:	ASYS-GLASS-PLATEN-280-A
Парткод:	6LE60740000

Деталь:	ASYS-GLASS-PLATEN-280-K
Парткод:	6LE60740200

Деталь:	GEAR-10H21-10S20-6-FUS
Парткод:	6LA84140000

Деталь:	GEAR-10S18-6-BYP-TRAY
Парткод:	6LE53448000

Деталь:	ASYS-PAD-PUSHER-GUIDE
Парткод:	6LE53488000

Деталь:	GEAR-10S23_P2STE62_10H21R
Парткод:	6LE56641000

Деталь:	ASYS-GEAR-5H56L-6-COUPL
Парткод:	6LE56639000

Деталь:	ASYS-GEAR-10S24_P2STE30
Парткод:	6LE56637000

Деталь:	ASYS-CASE-DEV-280
Парткод:	6LE55918000

Деталь:	PLATE-SIDE
Парткод:	6LA81632000

Деталь:	S/FHEXM-M3X10-NI
Парткод:	X0-02232000

Деталь:	MIXER-1-371
Парткод:	6LA81635000

Деталь:	GEAR-10S37_10H17R_10S19-8
Парткод:	6LE56646000

Деталь:	GEAR-5H60L-6-WORM-TNR
Парткод:	6LE56633000

Деталь:	ASYS-BRKT-DRV-FEED-280
Парткод:	6LE56624000

Error code:	C01
Display:	C01-xxx No Ink Replace Ink Cartridge
Description:	Main motor is abnormal
Remedy:	Is the main motor working? NO 1. Check if the connector CN1 of the main motor is disconnected. 2. Check if the connector J313 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circutied. 4. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 5. Replace the main motor. 6. Replace the LGC board. YES Is the LED on the main motor board lit without flickering? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 3. Replace the main motor. 4. Replace the LGC board. YES 1. Check if the PLL lock signal J313-11 output from the LGC board is always level “L”? 2. Check if the voltage supplied to the microcomputer input terminal IC10-7 is always “L”? 3. Replace the LGC board.

Error code:	C21
Description:	Carriage initialization error
Remedy:	1 Does the CIS case move to its home position when the power is turned ON? Yes 1. Check if the CIS home position sensor is installed properly. 2. Check if any of the connectors is disconnected from the CIS home position sensor. 3. Check if the connector CN14 on the MAIN board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the MAIN board are short circuited or open circuited. 6. Replace the CIS home position sensor. 7. Replace the MAIN board. No 2 2 Is there any abnormal sound when the CIS case is moving? Yes 1. Check if the CIS unit drive belt-1 or the CIS unit drive belt-2 is damaged. 2. Check if the belt tension of the CIS unit drive belt-1 or the CIS unit drive belt-2 is loose. 3. Check if the joint of the belt stopper and the CIS unit drive belt-1 is loose. No 3 3 1. Check if the tension of the CIS unit drive belt-1 or the CIS unit drive belt-2 is too tight. 2. Check if any of the connectors of the scan motor is disconnected. 3. Check if the connector CN18 on the MAIN board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the MAIN board are short circuited or open circuited. 6. Replace the scan motor. 7. Replace the MAIN board

Error code:	C26
Description:	Peak detection error
Remedy:	Does the exposure lamp light? (Perform the output check in the test mode: 03-267) YES 1. Check if the connectors on the CCD and SLG boards are disconnected. 2. Check if the shading correction plate is dirty. 3. Check if the conductor pattern on the CCD board is short- or open-circuited. 4. Check if the conductor pattern on the SLG board is short- or open-circuited. 5. Replace the lens unit. 6. Replace the SLG board. NO 1. Check if the connectors of the exposure lamp and inverter are disconnected. 2. Check the SLG board if the connector pin J9 is disconnected and the harness is short- or opencircuited. 3. Check if the conductor pattern on the SLG board is short- or open-circuited. 4. Replace the SLG board. 5. Replace the inverter. 6. Replace the exposure lamp.

Error code:	C41
Description:	Thermistor or heater abnormal when warming-up is started
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C43
Description:	Thermistor abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C44
Description:	Heater abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C45
Description:	Abnormal side thermistor after the copier has become ready
Causes:	MAIN board Switching regulator
Remedy:	1. Check the side thermistor (1) Check if the connector is disconnected. (2) Check if the side thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the side thermistor is open-circuited. 2. Check the LGC board (1) Check if the connector J334 is disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) “6” to “0”.

Toshiba DP-1640

Модули

Детали MAIN-CHARGER-ASY

Коды ошибок

Описание

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Error code:	C55
Description:	RADF I/F error
Remedy:	Is the harness between the ADF board and SLG board open-circuited? Replace the harness. Is the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. Replace the SLG board.

Error code:	C94
Description:	LGC-CPU abnormal
Remedy:	Is "Call for service" displayed again even after the copier is turned OFF and then back ON? N: Observe the condition for a while. Y: 1. Check if the conductor pattern between LGC-CPU (IC32) and FROM (IC24) is open- or short-circuited. 2. If this problem recurs frequently, replace the LGC board.

Error code:	C97
Description:	Vacuum fan motor abnormality
Remedy:	Check the High-voltage transformer. 1. Is the main charger installed securely? 2. Check if the spring of high-voltage supply contact point is deformed. 3. Check if the needle electrode is broken or the main charger grid is deformed. 4. Check if any foreign matters is on the needle electrode or the main charger grid. 5. Is the transfer/separation charger installed securely? 6. Check if the transfer/separation charger wire is broken or unhooked. 7. Check if any foreign matter is on the transfer/separation charger wire.

Error code:	CA1
Description:	Polygonal motor rotation abnormal
Remedy:	Is the polygonal motor rotating? N: 1. Check if the polygonal motor connector is disconnected. 2. Check if connector J181 or J188 on the IMC board is disconnected. 3. Check if any harness is open-circuited or any connector pin is disconnected. 4. Check if any conductor pattern on the IMC board is open- or short-circuited. 5. Replace the IMC board. 6. Replace the laser optical unit. Y: Are both 10th and 12th pins of the connector J188 on the IMC board always at the level "L"? N: 1. Check if any conductor pattern on the IMC board is open- or short-circuited . 2. Replace the IMC board. 3. Replace the laser optical unit. Y: 1. Check if any conductor pattern on the IMC board is open- or short-circuited . 2. Replace the IMC board. 3. Replace the laser optical unit.

Error code:	CA2
Description:	H-SYNC abnormal
Remedy:	Is the polygonal motor rotating? N: Refer to "[CA1] Polygonal motor rotation abnormal". Y: Are both 10th and 12th pins of the connector J188 on the IMC board always at the level "L"? N: Refer to "[CA1] Polygonal motor rotation abnormal". Y: Is the harness between the RLY and IMC boards open-circuited? Are the connector J185 on the IMC board or the connector J201 on the RLY board disconnected? Y: Replace the harness. Reconnect the connectors. N: 1. Replace the IMC board. 2. Replace the laser optical unit.

Error code:	E01
Description:	Paper leading edge not reaching the exit sensor
Remedy:	Is the fuser motor rotating? Y: Is the harness between the LGC board and the exit sensor open-circuited? Is the connector of the paper exit sensor or the connector J123 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the exit sensor. 2. Replace the LGC board. N: Is the harness between the LGC board and the paper exit sensor open-circuited? Is the fuser motor connector or the connector J122 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the fuser motor. 2. Replace the LGC board. Where was the paper stopped? Near the exit sensor (paper not damaged) Are the registration seRemove the paper after the fuser unit cools down.nsor and paper exit sensor functioning properly? (Does the actuator return normally?) Y: 1. In the tRemove the paper after the fuser unit cools down.est mode (03) check if each sensor is functioning. 2. Reconnect each sensor connector. N: Repair the actuator if it has come off. Before reaching the fuser unit Did the paper stop, curling upward excessively? Y: Replace the paper in the cassette. From the transfer belt surface to the exit sensor Do the size of paper and the size set match? N: Make the sizes match. Y: Is the transfer belt moving? Is the black drum motor or the transfer belt motor stopped? Or is any abnormal noise heard from one of them due to loss of synchronism? Y: 1. Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. 2. Check the motor connector, and the connector J130 on the LGC board. 3. Replace the motor. 4. Replace the LGC board. No paper found Is the paper attached to the fuser belt? Remove the paper after the fuser unit cools down.

Error code:	E02
Display:	E02-xxx !!Maintenance!! Call Service
Description:	Paper trailing edge not passing the exit sensor
Remedy:	Is the fuser motor rotating? Y: Is the harness between the LGC board and the exit sensor open-circuited? Is the connector of the paper exit sensor or the connector J123 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the exit sensor. 2. Replace the LGC board. N: Is the harness between the LGC board and the paper exit sensor open-circuited? Is the fuser motor connector or the connector J122 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the fuser motor. 2. Replace the LGC board. Where was the paper stopped? Near the exit sensor (paper not damaged) Are the registration seRemove the paper after the fuser unit cools down.nsor and paper exit sensor functioning properly? (Does the actuator return normally?) Y: 1. In the tRemove the paper after the fuser unit cools down.est mode (03) check if each sensor is functioning. 2. Reconnect each sensor connector. N: Repair the actuator if it has come off. Before reaching the fuser unit Did the paper stop, curling upward excessively? Y: Replace the paper in the cassette. From the transfer belt surface to the exit sensor Do the size of paper and the size set match? N: Make the sizes match. Y: Is the transfer belt moving? Is the black drum motor or the transfer belt motor stopped? Or is any abnormal noise heard from one of them due to loss of synchronism? Y: 1. Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. 2. Check the motor connector, and the connector J130 on the LGC board. 3. Replace the motor. 4. Replace the LGC board. No paper found Is the paper attached to the fuser belt? Remove the paper after the fuser unit cools down.

Error code:	E03
Description:	Paper remaining inside the copier at power ON
Remedy:	Is any paper remaining inside the copier? Y: Remove the paper. N: Refer to [E01], [E02] and [E11] to [E26].

Error code:	E09
Description:	Jam caused by an abnormal HDD
Remedy:	(1) Check if the connectors of the HDD are disconnected. (2) Check if the connector pins are disconnected and the harnesses are open-circuited. (3) Replace the HDD. (4) Replace the SYS board.

Error code:	E12
Display:	E12-Output Bin Full, Top
Description:	Top Output Tray is Full, Unload Paper
Remedy:	1 Visually inspect the Stack Full Actuator and use service diagnostics to test the Stack Full Sensor. Does the sensor and actuator operate correctly? Go to step [3]. Replace the actuator if broken. If the sensor is not working, go to step [2}. 2 Check Pin 6 OPTN cable at the Engine Controller Board for +5 volts. Replace the Engine Controller Board. Go to step [3]. 3 Check the Stack Full Sensor wiring harness to the Toner Sensor Board Pin 3 for +5 volts. Go to step [4]. Replace the Stack Full Sensor and wiring. 4 Check for +5 volts at Pin 6 OPTN cable to the Toner Sensor Board. Replace the ribbon cable (OPTN) Replace the Toner Sensor Board.