Toshiba DP-5510

Рейтинг

Парткаталог
Коды ошибок

Модули

OPTICAL-ELECTRIC-ASM

USED-TONER AUGER-ASM

MANUAL-TRAY-ASM

MANUAL-FEED-DRIVE-1-ASM

CLEANER-1-ASM

DEVELOPER-1-ASM

FEED-DRIVE-ASM

TRANSPORT-BELT-DRIVE-2-ASM

UPPER-FRAME-ASM

DEVELOPER-COVER-ASM

FEED-1-ASM

FEED-2-ASM

DEVELOPER-2-ASM

DRUM DRUM-DRIVE ASM

TRANSPORT-BELT-CASE-2-ASM

OPTICAL-DRIVE-ASM

TONNER-DRIVE-ASM

PAPER-FEED-ASM

CRG-2-ASM

REAR-FRAME-2-ASM

TRANSPORT-BELT-GUIDE-2

TRANSPORT-BELT-CASE-1-ASM

DEV DRIVE/STAY-ASM

FEED-3-ASM

COVER-ASM

REVERSE-DRIVE-ASM

HINGE-ASM

REAR-FRAME-1-ASM

FUSER-3-ASM

ALIGNING-ROLLER-ASM

RECYCLE AUGER-ASM

TANDEM-LCF-2-ASM

PLATEN-ASM

MANUAL-FEED-DRIVE-2-ASM

CLEANER-2-ASM

CASSETTE-ASM

COVER-1-ASM

OPTICAL-FRAME-ASM

FUSER-1-ASM

TRANSPORT-ROLLER-ASM

TANDEM-LCF-1-ASM

REVERSE-OPEN-GUIDE-2-ASM

ELECTRIC-ASM

FEED-5-ASM

PM-KIT

SUPPLIES

CONTROL-PANEL-ASM

REPLACE UNIT

LASER-OPT-ASM

FEED-DRIVE-1-ASM

CHARGER-DRIVE-ASM

COVER-2-ASM

GUIDE-OPEN-ASM

TRANSPORT-BELT-DRIVE1

FEED-4-ASM

FUSER-2-ASM

FUSER-DRIVE-ASM

LOWER-FRAME-ASM

MAIN-CHARGER-ASM

FEED-DRIVE-2-ASM

TRANSPORT-BELT-GUIDE-1

LGC & SYS-ASM

CLEANER-3-ASM

REVERSE-OPEN-GUIDE-1-A

TRAY-ASM

FRONT-FRAME-ASM

CRG-1-ASM

Детали REAR-FRAME-1-ASM

Деталь:	STAY-REAR-HOR
Парткод:	6LA01017000

Деталь:	BRKT-CASE-L
Парткод:	6LA01025000

Деталь:	SPS-3U
Парткод:	F0-00027000

Деталь:	SPLSN-4U
Парткод:	F0-00340000

Деталь:	LWS-2U
Парткод:	F0-00341000

Деталь:	LWS-3U
Парткод:	F0-00025000

Деталь:	EDS-1717U
Парткод:	F0-00047000

Деталь:	EDS-1
Парткод:	F0-00045000

Деталь:	SPLSN-8U
Парткод:	F0-00343000

Деталь:	BD/W-TWS-3027
Парткод:	4406509170

Деталь:	COVER-TLCF-FRM
Парткод:	6LA01041000

Деталь:	BRKT-HINGE-BYP
Парткод:	6LA04747000

Деталь:	HRNS-PLG-SYS-340
Парткод:	6LA07447000

Деталь:	HRNS-HVT-M-340
Парткод:	6LA07393000

Деталь:	HRNS-HVT-TR-340
Парткод:	6LA07394000

Деталь:	K-JOINT-RGT
Парткод:	4406349900

Деталь:	K-BKT-HINGE-FED
Парткод:	6LA04139000

Деталь:	SEAL-FRAME-R
Парткод:	6LA01386000

Деталь:	BRKT-DRIVE-MID
Парткод:	6LA04261000

Деталь:	SHAFT-DRIVE-MID
Парткод:	6LA04262000

Деталь:	BUSH-6-GCB
Парткод:	4407734980

Деталь:	P/PRL/AH7-2X12-SS
Парткод:	X0-01526000

Деталь:	GEAR-10S035-06
Парткод:	6LA04263000

Деталь:	GP1A73A
Парткод:	C0-03663000

Деталь:	OCB-375
Парткод:	F0-00370000

Деталь:	HRNS-LGC-SFB-340
Парткод:	6LA07337000

Деталь:	HRNS-LGC-CSTL-340
Парткод:	6LA07338000

Деталь:	HRNS-LGC-CSTU-340
Парткод:	6LA07339000

Деталь:	HRNS-LGC-BTM-340
Парткод:	6LA07340000

Деталь:	HRNS-LGC-LCF-340
Парткод:	6LA07384000

Деталь:	HRNS-HVT-BRS-340
Парткод:	6LA07409000

Деталь:	HRNS-LGC-REV-340
Парткод:	6LA07341000

Деталь:	LWS-1U
Парткод:	F0-00024000

Деталь:	BRKT-HINGE-STOP
Парткод:	6LA01045000

Деталь:	SUPPORT-GUIDE-P
Парткод:	4401772280

Деталь:	K-JNT-GUIDE-U-S
Парткод:	6LA03350000

Деталь:	BRKT-FUS-DRV
Парткод:	6LA05330000

Деталь:	EDS-2
Парткод:	F0-00041000

Деталь:	EMT-3N
Парткод:	F0-00841000

Деталь:	S/BID-M4X6-NC
Парткод:	X0-01285000

Деталь:	S/TPS/HEX-48-NI
Парткод:	6LA08913000

Деталь:	RR/E-5-ZC
Парткод:	X0-01266000

Деталь:	S/TPS/HEX-38-NI
Парткод:	6LA08909000

Деталь:	ASY-HRNS-CST-340
Парткод:	6LA07438000

Деталь:	ARM-S-LATCH
Парткод:	6LA09329000

Деталь:	WH-RD-SNS-551
Парткод:	6LA09148000

Деталь:	ASY-L-SOL-SUB
Парткод:	6LA09098000

Деталь:	ASY-EST-SOL-SUB
Парткод:	6LA09100000

Деталь:	ASYS-SB-IDLER
Парткод:	6LA09096000

Деталь:	BRKT-R-SOL-LS
Парткод:	6LA09268000

Деталь:	BRKT-SB-RELEASE
Парткод:	6LA09307000

Деталь:	BRKT-SB-RELEAS
Парткод:	6LA09291000

Деталь:	BUSH6
Парткод:	6LA09062000

Деталь:	CLIP4
Парткод:	6LA09074000

Деталь:	CVR-S-LATCH
Парткод:	6LA09222000

Деталь:	DUCT-F
Парткод:	6LA09242000

Деталь:	HLDR-DF-SNS
Парткод:	6LA09230000

Деталь:	MYR-R-CLEAN
Парткод:	6LA09238000

Деталь:	LVR-DF-SNS
Парткод:	6LA09231000

Деталь:	LVR-R-SOL-LS
Парткод:	6LA09184000

Деталь:	LVR-SB-RELS-SOL
Парткод:	6LA09236000

Деталь:	PLT-T-SP
Парткод:	6LA09303000

Деталь:	RINK-SB-RELAS-1
Парткод:	6LA09228000

Деталь:	RINK-SB-RELAS-2
Парткод:	6LA09229000

Деталь:	RUB-O-RING
Парткод:	6LA09401000

Деталь:	SCR-M3X6BISR-NI
Парткод:	6LA09399000

Деталь:	SCR-M3X6ITSR-NI
Парткод:	6LA09396000

Деталь:	SPE-DF-SNS
Парткод:	6LA09383000

Деталь:	SPE-R-LSF
Парткод:	6LA09353000

Деталь:	SPE-SB-IDLER
Парткод:	6LA09384000

Деталь:	SPC-SB-RELEASE
Парткод:	6LA09375000

Деталь:	SPC-S-LATCH
Парткод:	6LA09369000

Деталь:	SPL-T-HOK
Парткод:	6LA09385000

Деталь:	SNS-TLP1241
Парткод:	6LA09019000

Деталь:	SCRW-030060FNWS
Парткод:	6LA09010000

Деталь:	SCRW-3008FNBB
Парткод:	6LA09011000

Деталь:	HPIN20/12SCH
Парткод:	6LA09039000

Коды ошибок

C04

C13

C14

C15

C16

C18

C1A

C1C

C26

C27

C28

C36

C37

C41

C43

C44

C45

C46

C47

C48

C49

C4A

C55

C56

C57

C58

C59

C73

C82

C83

C84

C85

C86

C94

CA1

CA2

CA3

CA5

CA6

CA9

CAA

CAB

CAC

CB1

CB2

CB3

CB4

CB5

CB6

CB7

CB8

CB9

CBA

CBB

CBC

CBD

CBE

CBF

CC0

CC1

CC2

CC4

CC5

CC6

CC7

CCC

CCD

CCE

CD0

CD1

CD2

CD3

CD4

CD5

CE0

CE1

CE2

CE3

CE4

E01

E02

E03

E09

E11

E12

E13

E14

E15

E16

E18

E19

E20

E21

E22

E23

E24

E25

E30

E31

E32

E33

E34

E35

E36

E37

E38

E3C

E3D

E3E

E3F

E41

E44

E45

E46

E47

E50

E51

E52

E54

E55

E57

E58

E59

E5A

E71

E72

E73

E74

E76

E77

E7A

E7B

E7C

E7D

E7E

E7F

E80

E81

E82

E83

E84

E85

E9F

EA1

EA2

EA3

EA4

EA5

EA6

EA7

EA8

EA9

EAA

EAB

EAC

EAD

EAE

EB3

EB5

EB6

EC0

EC1

EC2

EC3

EC4

EC5

EC6

EC7

EC8

EC9

ECA

ECB

ECC

F07

F10

F11

Деталь:	ASYS-MOTR.D-MCH-CL-340
Парткод:	6LA07162000

Error code:	C04
Display:	C04-xxx Add Paper
Description:	Abnormal feed motor
Causes:	402 Paper detection sensor is OFF (not detecting paper).
Remedy:	Is the PFP motor working? (Perform the output check in the test mode: 03-125/175) NO 1. Check if the signal line connector of the feed motor is disconnected. 2. Check if the connector J327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the feed motor board and LGC board are short- or open circuited. 5. Replace the feed motor. 6. Replace the LGC board. YES Is the LED on the feed motor board lit without flashing? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the feed motor board and LGC board are short- or open-circuited. 3. Replace the feed motor. 4. Replace the LGC board. YES Replace the LGC board.

Error code:	C13
Description:	1st cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C14
Description:	2nd cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C15
Description:	3rd cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C16
Description:	4th cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C18
Description:	LCF tray operation abnormal
Remedy:	Is the harness between the LGC board and the LCF unit open-circuited? Is the relay connector of the harness between the LGC board and the LCF unit or the connector J105 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: Are the switches and sensors in the LCF unit working properly? Y: 1. Replace the LCF tray motor. 2. Replace the LGC board. N: 1. Replace the sensors and switches. 2. Replace the LCF drive PC board or the LCF tray-down switch PC board. 3. Replace the LGC board.

Error code:	C1A
Description:	Abnormal tandem LCF end fence motor (Paper can be fed from cassettes other than the tandem LCF cassette.)
Remedy:	Is the LCF end fence motor working? (Perform the output check in the test mode: 03-207) NO 1. Check if the connector of the tandem LCF end fence motor is disconnected. 2. Check if the connector J346 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Are the tandem LCF end fence home/stop position sensors working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[7]/[A], /[7]/[B]) NO 1. Check if the connectors of the sensors are disconnected. 2. Check if the connector J346 on the LGC board is disconnected. 3. Check if the slit reaches the sensors. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the driving mechanism is abnormal. 2. Check if the conductor pattern on the LGC board is short- or open-circuited. 3. Replace the LGC board.

Error code:	C1C
Description:	Abnormal external LCF tray-up motor (Paper can be fed from cassettes other than the external LCF)
Remedy:	Is the tray motor driving? (Perform the output check in the test mode: 03-271) 1. Check if the connector J815 on the LCF tray motor is not disconnected. 2. Check if the connectors J801~804 on the LCF board are not disconnected. 3. Check if the connector of the tray-up sensor is not disconnected. 4. Check if the actuator reaches the sensor. 5. Check if the power (24V) is supplied to 1pin and 2pin of J803. If not, check if the door switch is turned ON and the harness of it is not open-circuited. 6. Replace the LCF board. 7. Replace the LGC board. Is the tray-up sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER] OFF/[1]/[C] 1. Check if the connector of the tray-up sensor is not disconnected. 2. Check if the connectors J801~804 on the LCF board are not disconnected. 3. Check if the actuator reaches the sensor. 4. Check if the coppector pins are not disconnected and the harness is not open-circuited. 5. Replace the LCF board. 6. Replace the LGC board. 1. Check if the tray lifting mechanism has no abnormality. 2. Replace the LCF board. 3. Replace the LGC board.

Error code:	C26
Description:	Peak detection error
Remedy:	Does the exposure lamp light? (Perform the output check in the test mode: 03-267) YES 1. Check if the connectors on the CCD and SLG boards are disconnected. 2. Check if the shading correction plate is dirty. 3. Check if the conductor pattern on the CCD board is short- or open-circuited. 4. Check if the conductor pattern on the SLG board is short- or open-circuited. 5. Replace the lens unit. 6. Replace the SLG board. NO 1. Check if the connectors of the exposure lamp and inverter are disconnected. 2. Check the SLG board if the connector pin J9 is disconnected and the harness is short- or opencircuited. 3. Check if the conductor pattern on the SLG board is short- or open-circuited. 4. Replace the SLG board. 5. Replace the inverter. 6. Replace the exposure lamp.

Деталь:	PWA-F-SLG-340
Парткод:	6LA06995000

Деталь:	HRNS-SLG-SYS-340
Парткод:	6LA07445000

Деталь:	HRNS-SCN-M-340
Парткод:	6LA07323000

Деталь:	HRNS-DF-340
Парткод:	6LA07444000

Error code:	C27
Description:	Carriage home position sensor not turning OFF within a fixed time
Causes:	• If the Master sensor does not find master on the Drum when the Drum is at 79° during the printing movement.
Remedy:	Are the carriages stuck at a point other than the home position? Y: Check the SCM and SDV boards for any abnormal circuit. N: 1. Check if any connector pin is disconnected, or any harness is open- or short-circuited. 2. Check the scan motor drive pulley if its screws are loose. 3. Check if any conductor pattern on the SDV board is open- or short-circuited. 4. Check if any conductor pattern on the SCM board is open- or short-circuited. 5. Replace the SDV board. 6. Replace the SCM board.

Error code:	C36
Description:	Abnormal main charger wire cleaner drive motor
Remedy:	(1) Check if the main charger is not disconnected. (2) Check if the wire cleaner drive motor is driving. (3) Replace the LGC board.

Error code:	C37
Description:	Abnormal transfer belt cam motor
Causes:	• During the Original set movement, if the Original IN sensor does not detect Original (sensor light not reflected) within 1712 pulses after the Read pulse motor activates. • During the Original set movement, if the Original IN sensor stops detecting the Original before the Read pulse motor activates 347 pulses.
Remedy:	(1) Check if the connector of the transfer belt cam motor is not disconnected. (2) Check if the transfer belt contact/release switch is working properly. (3) Replace the transfer belt cam motor. (4) Replace the LGC board.

Error code:	C41
Description:	Thermistor or heater abnormal when warming-up is started
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C43
Description:	Thermistor abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C44
Description:	Heater abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C45
Description:	Abnormal side thermistor after the copier has become ready
Causes:	MAIN board Switching regulator
Remedy:	1. Check the side thermistor (1) Check if the connector is disconnected. (2) Check if the side thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the side thermistor is open-circuited. 2. Check the LGC board (1) Check if the connector J334 is disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) “6” to “0”.

Error code:	C46
Description:	Heater abnormal (low temperature) after the copier has become ready
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C47
Description:	Rear thermistor abnormal after the copier has become ready
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C48
Description:	Heater abnormal (high temperature)
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Toshiba DP-5510

Модули

Детали REAR-FRAME-1-ASM

Коды ошибок

Описание

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Error code:	C49
Description:	Abnormal IH circuit or coil
Causes:	• If the actuator of the Master disposal unit set switch is not depressed.
Remedy:	1. Check the IH control board (1) Check if the conductor pattern on the board is short or open-circuited. (2) Replace the IH control board. 2. Check the IH coil (1) Check if the coil is broken or shorted. (2) Replace the IH coil. 3. Clear the status counter Change the values “13”, “15”, “16” or “19” of the status counter (08-400) to “0”. * The status counter value is as follows in the following cases. Change them to "0" respectively. • The error occurred before the temperature of the fuser roller reaches 40°C: "13" • The error occurred before the temperature of the fuser roller reaches 150°C: "16" • The error occurred before the machine has become ready: "15" • The error occurred when the machine is in the ready state: "19" [C47], [C48] and [C49] can be cleared by turning OFF and ON the main switch as long as the problem was solved, and the status counter does not have to be changed to "0". The value of the status counter remains until the next service call overwrites the value.

Error code:	C4A
Description:	Cleaning web finished
Remedy:	(1) Check if the cleaning web is remaining. (2) Check if the connector J332 on the LGC board is not disconnected. (3) Check if there is no abnormality at the web sensor. (4) Replace the LGC board.

Error code:	C55
Description:	RADF I/F error
Remedy:	Is the harness between the ADF board and SLG board open-circuited? Replace the harness. Is the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. Replace the SLG board.

Error code:	C56
Description:	Communication error between main CPU and PFC
Causes:	• If the ADF unit set sensor does not detect the ADF unit.
Remedy:	(1) Check if the conductor pattern around IC57 and IC58 is not short- or open-circuited. (2) Replace the LGC board.

Error code:	C57
Description:	Communications error between LGC-CPU and IPC board
Remedy:	(1) Check if any conductor pattern on the LGC board, mainly around IC23, IC72, IC74 and J125, is short- or open-circuited. (2) Check if the conductor pattern on the IPC board is short- or open-circuited. (3) Replace the IPC board. (4) Replace the LGC board.

Error code:	C58
Description:	Communication error between IPC board and finisher
Causes:	• If the actuator of the Master making unit set switch is not depressed.
Remedy:	Is a specified finisher used? Replace to the specified finisher. Is the harness between the IPC board and finisher control board open-circuited? Replace the harness. Is the conductor pattern on the IPC board is short- or open-circuited? Replace the IPC board. Replace the finisher control board.

Error code:	C73
Description:	EEPROM initializing error
Remedy:	1. Check if any conductor pattern on the RADF PC board is open- or short-circuited mainly around IC7. 2. Replace the RADF PC board. 3. Initialize the RADF`s EEPROM and perform the sensor automatic adjustment.

Error code:	C82
Description:	Communications error between scanner and ADF
Remedy:	1. Check if the connectors are disconnected or the harnesses are open-circuited between the SCM board and RADF PC board (includig the relay connector). 2. Replace the RADF PC board. 3. Replace the SCM board.

Error code:	C83
Description:	Original length sensor adjustment error
Remedy:	Is there any extraneous material between the original length sensor and reflective mirror? Remove the extraneous material. Is the reflective mirror tainted? Clean up the mirror. Is the conductor pattern around IC6, IC11 and CN15 on the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. 1. Replace the original length sensor. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment.

Error code:	C84
Description:	Small original reverse sensor adjustment error
Remedy:	Is there any extraneous material between the small original reverse sensor and reflective mirror? Remove the extraneous material. Is the reflective mirror tainted? Clean up the mirror. Is the conductor pattern around IC6, IC11 and CN16 on the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. 1. Replace the small original reverse sensor. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment.