Toshiba e-Studio 160

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Число страниц в месяц

20000

Цветность печати

черно-белая

Общие характеристики
Тип устройства	МФУ
Телефон
Факс
Печать фотографий
Копир
Сканер
Число страниц в месяц	20 000
Размещение	напольный
Область применения	малый офис
Цветность печати
Тип	лазерный/светодиодный
Технология печати	лазерная
Макс. формат	A3
Принтер
Двусторонняя печать
Макс, разрешение для ч/б печати
По X	600
По Y	600
Скорость ч/б печати
A3	10
Копир
Макс, количество копий за цикл	999
Время выхода первой копии	8
Макс, разрешение (ч/б)
По X	600
По Y	600
Скорость цветного копирования
A4	16
Сканер
Устройство автоподачи оригиналов	одностороннее
Макс. формат оригинала	A3
Оттенки серого	256
Расходные материалы
Ресурс фотобарабана	27 000
Ресурс девелопера	81 000
Печать на:
Пленках
Этикетках
Карточках
Телефон
Caller ID
Спикерфон
Стандарт DECT
Автоответчик
АОН
Беспроводная трубка
Проводная трубка
Лотки
Подача бумаги
Стандартная	550
Вывод бумаги
Стандартный	250
Финишер
Сортер
Сортировка со сдвигом
Интерфейсы
Ethernet (RJ-45)
Память/Процессор
Объем памяти	32
Габариты
Глубина	554
Ширина	530
Вес	50
Высота	600

Модули

SERVICE TOOLS

CHARGER

Cover 1

GLASS-PLTN

FEEDER

ELECTRIC

FRAME

LVPS/ LSU

MAIN-DRIVE

Exit

FUSER (e-STUDIO200/250)

FUSER (DP2000/2500)

DRUM

OPTICS-DRIVE 2 (e-STUDIO160/200/250)

GUIDE-P/U

Cover 2

FUSER (DP1600)

CONTROL-PANEL

TRAY-UP

GUIDE 2ND

OPTICS-DRIVE 1 (e-STUDIO160/200/250)

PM KIT

OPTICS-DRIVE 1 (DP1600/2000/2500)

CASSETTE

OPTICS-DRIVE 2 (DP1600/2000/2500)

DEV. MOTOR

FUSER (e-STUDIO160)

Developer

Детали LVPS/ LSU

Деталь:	DUCT-UPPER-SIDE
Парткод:	41306307000

Деталь:	DUCT-LOWER-SIDE
Парткод:	41306308000

Деталь:	WH-24VCOS-AT
Парткод:	41301068000

Деталь:	SM-V-21522-3C6
Парткод:	41301079000

Деталь:	FAN-EXHAUST
Парткод:	41306518000

Деталь:	SHIELD-AC
Парткод:	41305020000

Деталь:	HOLDER-INLET
Парткод:	41305024000

Деталь:	LID-CONNECTOR
Парткод:	41305083000

Деталь:	JP-NC-179-F6.35
Парткод:	4843309865

Деталь:	WH-AC-IO-AT
Парткод:	41301093000

Деталь:	WH-MAINSW-AT
Парткод:	41301078000

Деталь:	WH-LVPS-AT
Парткод:	41301085000

Деталь:	ASM-PG-LSU-S
Парткод:	41303621000

Деталь:	WH-LD-AT
Парткод:	41301122000

Деталь:	WH-PM-AT
Парткод:	41301081000

Деталь:	HOLDER-AU1
Парткод:	41306038000

Деталь:	SW-AJ8W200WW
Парткод:	4843232258

Деталь:	SP-CS1A-B2CA
Парткод:	4843232255

Деталь:	PLT-CO-SW
Парткод:	41305076000

Деталь:	WH-FCOS-AT
Парткод:	41301082000

Деталь:	LOCK-CART-TNR
Парткод:	41306284000

Деталь:	CLP-YMC-05-0
Парткод:	4842413233

Деталь:	CLP/W-CH-30
Парткод:	4843391729

Деталь:	CLP/W-WS-1NS
Парткод:	4843391725

Деталь:	BD/W-EDS-1
Парткод:	4843390941

Деталь:	BD/W-EDS-1717U
Парткод:	4843391164

Деталь:	WIRE/B-KG-010
Парткод:	4843391727

Деталь:	WH-PS-ACRLY-AT
Парткод:	41301028000

Деталь:	PWA-F-FUS-AT
Парткод:	41300515100

Деталь:	PWB/Z-WLS-10-0
Парткод:	4843391431

Деталь:	CLP/W-UAMS05S
Парткод:	4843391177

Деталь:	FRAME-SIDE-LEFT
Парткод:	41305153000

Деталь:	TBIDS3016MSZN3A
Парткод:	4842042071

Деталь:	TBIDS3030MSZN3A
Парткод:	4842042072

Деталь:	TBID3008MSZN3A
Парткод:	4842040685

Деталь:	PTBR30*08MSZN3A
Парткод:	4842040846

Деталь:	BID40*08MSCR1AI
Парткод:	7043400813

Деталь:	TBIDS3008MSCR1A
Парткод:	4842042065

Деталь:	TBID3006MSZN3L
Парткод:	4842040370

Деталь:	WH-HTLP-USAT
Парткод:	41301036000

Деталь:	WH-HTLP-AT
Парткод:	41301024000

Деталь:	WH-MAINSW-R-AT
Парткод:	41301187000

Деталь:	WH-LVPS-AW
Парткод:	41309004000

Деталь:	PS-LVPS-ATUS
Парткод:	41301130000

Деталь:	PS-LVPS-ATEU
Парткод:	41301130100

Деталь:	PS-LVPS-AW
Парткод:	41309022000

Деталь:	PS-LVPS-AW
Парткод:	41309022100

Деталь:	PS-LVPS-ATTW
Парткод:	41301130200

Деталь:	PS-LVPS-AW(TW)
Парткод:	41309022200

Деталь:	PS-LVPS-US-F250
Парткод:	6LA55566000

Деталь:	PS-LVPS-EU-F250
Парткод:	6LA55567000

Деталь:	ASM-PG-LSU-S
Парткод:	41303621100

Деталь:	ASYG-LSU-F250-S
Парткод:	6LA55886000

Деталь:	ASYG-LSU-F250-S
Парткод:	6LA55886100

Деталь:	WH-LD-CORE-AW
Парткод:	41309026000

Деталь:	HRNS-LD-F250
Парткод:	6LA55563000

Деталь:	HRNS-PM-F250
Парткод:	6LA55562000

Деталь:	SZ-AJ8R2004ZC
Парткод:	44205162000

Деталь:	PWA-F-FUS-AT
Парткод:	41300515200

Деталь:	SM-V-21522-3C6
Парткод:	41301175000

Деталь:	WH-FIN-IPC-CORE
Парткод:	41309025000

Деталь:	STAY-FINISHER
Парткод:	41321477000

Деталь:	STAY-LVPS-EMI
Парткод:	41305139000

Деталь:	PL-SHIELD-PFC
Парткод:	41305138000

Деталь:	BD/W-SKB-145P
Парткод:	4843390841

Деталь:	SHEET-1245-TWA
Парткод:	41314597000

Деталь:	WH-AC-RESET-AT
Парткод:	41301188000

Деталь:	CS1A-B2CA
Парткод:	E0-01853000

Деталь:	EDS-1
Парткод:	F0-00045000

Деталь:	EDS-1717U
Парткод:	F0-00047000

Деталь:	UAMS-05S-2
Парткод:	F0-00042000

Деталь:	S/TPS/BID-3X16-ZC
Парткод:	X0-01606000

Деталь:	S/TPS/BID-3X30-ZC
Парткод:	X0-01607000

Деталь:	S/BID-M4X8-NC
Парткод:	X0-01286000

Деталь:	S/TPS/BID-3X8-NC
Парткод:	X0-01444000

Деталь:	AJ8W200WW
Парткод:	E0-02356000

Деталь:	SKB-145P
Парткод:	F0-00261000

Коды ошибок

C01

C04

C06

C13

C14

C15

C16

C18

C19

C21

C25

C26

C38

C41

C43

C44

C45

C56

C57

C58

C71

C73

C74

C81

C82

C83

C91

C95

C96

C97

C98

C99

CA1

CA2

CB2

CB5

CC3

CC8

CC9

CCA

CCB

E01

E02

E03

E08

E09

E11

E12

E13

E14

E15

E16

E19

E31

E32

E33

E34

E35

E36

E41

E42

E43

E45

E71

E72

E73

E74

EA1

EA2

EA3

EA4

EA5

EA7

EAF

F11

F12

F13

F14

F31

F41

Error code:	C01
Display:	C01-xxx No Ink Replace Ink Cartridge
Description:	Main motor is abnormal
Remedy:	Is the main motor working? NO 1. Check if the connector CN1 of the main motor is disconnected. 2. Check if the connector J313 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circutied. 4. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 5. Replace the main motor. 6. Replace the LGC board. YES Is the LED on the main motor board lit without flickering? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 3. Replace the main motor. 4. Replace the LGC board. YES 1. Check if the PLL lock signal J313-11 output from the LGC board is always level “L”? 2. Check if the voltage supplied to the microcomputer input terminal IC10-7 is always “L”? 3. Replace the LGC board.

Error code:	C04
Display:	C04-xxx Add Paper
Description:	Abnormal feed motor
Causes:	402 Paper detection sensor is OFF (not detecting paper).
Remedy:	Is the PFP motor working? (Perform the output check in the test mode: 03-125/175) NO 1. Check if the signal line connector of the feed motor is disconnected. 2. Check if the connector J327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the feed motor board and LGC board are short- or open circuited. 5. Replace the feed motor. 6. Replace the LGC board. YES Is the LED on the feed motor board lit without flashing? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the feed motor board and LGC board are short- or open-circuited. 3. Replace the feed motor. 4. Replace the LGC board. YES Replace the LGC board.

Error code:	C06
Description:	Feed motor rotation abnormal
Causes:	859 No paper in Tray No.1
Remedy:	Is the paper feed motor rotating properly? N: 1. Check if the connector J41 of the paper feed motor is disconnected. 2. Check if the connector J109 on the LGC board is disconnected. 3. Check if the connector J703 of the switching power supply is disconnected. 4. Check if the harness between the LGC board and the paper feed motor is open-circuited. 5. Check if the harness between the switching power supply and the paper feed motor is open-circuited. 6. Check if any harness is open-circuited or any connector pin is disconnected. 7. Rotate the motor manually, clockwise as seen from its back, and if the motor load is abnormal, remove any foreign matter from the drive unit. 8. Replace the paper feed motor. 9. Replace the LGC board. Y: Are the pins A6 and A10 of the connector J109 on the LGC board always at the level "L"? N: 1. Check if the connector J41 of the paper feed motor is disconnected. 2. Check if the connector J109 on the LGC board is disconnected. 3. Check if any conductor pattern on the LGC board is open- or short-circuited. 4. Check if any harness is open-circuited or any connector pin is disconnected. 5. Replace the LGC board. 6. Replace the paper feed motor. Y: 1. Check if any conductor pattern on the LGC board is open- or short-circuited. 2. Replace the LGC board. 3. Replace the paper feed motor.

Error code:	C13
Description:	1st cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C14
Description:	2nd cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C15
Description:	3rd cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C16
Description:	4th cassette tray operation abnormal
Remedy:	Is the cassette pushed in properly to the copier? N: Push in the cassette properly to the copier. Y: Is the harness between the LGC board and the cassette tray-up limit sensor open-circuited? Is the harness between the LGC board and the cassette tray-up motor open-circuited? Is the cassette tray-up limit sensor connector, cassette tray-up motor connector, or connector J106 on the LGC board disconnected? Y: 1. Reconnect the connector. 2. Replace the harness. N: Is the gear of the cassette tray-up motor unit broken? Y: Replace the gear. N: 1. Replace the cassette tray-up motor. 2. Replace the cassette tray-up limit sensor. 3. Replace the paper feed unit. 4. Replace the LGC board.

Error code:	C18
Description:	LCF tray operation abnormal
Remedy:	Is the harness between the LGC board and the LCF unit open-circuited? Is the relay connector of the harness between the LGC board and the LCF unit or the connector J105 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: Are the switches and sensors in the LCF unit working properly? Y: 1. Replace the LCF tray motor. 2. Replace the LGC board. N: 1. Replace the sensors and switches. 2. Replace the LCF drive PC board or the LCF tray-down switch PC board. 3. Replace the LGC board.

Error code:	C19
Description:	LCF feed motor abnormal (DP2000/2500 series)

Error code:	C21
Description:	Carriage initialization error
Remedy:	1 Does the CIS case move to its home position when the power is turned ON? Yes 1. Check if the CIS home position sensor is installed properly. 2. Check if any of the connectors is disconnected from the CIS home position sensor. 3. Check if the connector CN14 on the MAIN board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the MAIN board are short circuited or open circuited. 6. Replace the CIS home position sensor. 7. Replace the MAIN board. No 2 2 Is there any abnormal sound when the CIS case is moving? Yes 1. Check if the CIS unit drive belt-1 or the CIS unit drive belt-2 is damaged. 2. Check if the belt tension of the CIS unit drive belt-1 or the CIS unit drive belt-2 is loose. 3. Check if the joint of the belt stopper and the CIS unit drive belt-1 is loose. No 3 3 1. Check if the tension of the CIS unit drive belt-1 or the CIS unit drive belt-2 is too tight. 2. Check if any of the connectors of the scan motor is disconnected. 3. Check if the connector CN18 on the MAIN board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the MAIN board are short circuited or open circuited. 6. Replace the scan motor. 7. Replace the MAIN board

Деталь:	SPE-TENS-WIRE
Парткод:	41306911000

Деталь:	JIG-CCDUNIT-AT
Парткод:	41306913000

Деталь:	ASM-HLD-W-AT
Парткод:	41306915000

Деталь:	SPE-TENS-BELT
Парткод:	41306912000

Error code:	C25
Description:	Scanner unit watch dog error
Causes:	• If the Master removal sensor does not detect the removed master (light path opened) when the Drum rotates to either 70° or 90° from the position-A during the master removal, when a master was detected on the Drum.
Remedy:	Drum Set Sensor OFF & 2 seconds later ON.

Error code:	C26
Description:	Peak detection error
Remedy:	Does the exposure lamp light? (Perform the output check in the test mode: 03-267) YES 1. Check if the connectors on the CCD and SLG boards are disconnected. 2. Check if the shading correction plate is dirty. 3. Check if the conductor pattern on the CCD board is short- or open-circuited. 4. Check if the conductor pattern on the SLG board is short- or open-circuited. 5. Replace the lens unit. 6. Replace the SLG board. NO 1. Check if the connectors of the exposure lamp and inverter are disconnected. 2. Check the SLG board if the connector pin J9 is disconnected and the harness is short- or opencircuited. 3. Check if the conductor pattern on the SLG board is short- or open-circuited. 4. Replace the SLG board. 5. Replace the inverter. 6. Replace the exposure lamp.

Error code:	C38
Description:	Auto-toner error (K)
Causes:	• During the Original scanning, if the Original IN sensor keeps detecting Original (sensor light reflected) and does not stop detecting within 4945 pulses after the Read pulse motor activates.
Remedy:	Is the harness between the LGC board and the EPU drawer connector open-circuited? Is any harness inside the EPU or the auto-toner sensor harness open-circuited? Is the auto-toner sensor connector or the connector J120 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the auto-toner sensor. 2. Replace the LGC board.

Error code:	C41
Description:	Thermistor or heater abnormal when warming-up is started
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C43
Description:	Thermistor abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C44
Description:	Heater abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C45
Description:	Abnormal side thermistor after the copier has become ready
Causes:	MAIN board Switching regulator
Remedy:	1. Check the side thermistor (1) Check if the connector is disconnected. (2) Check if the side thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the side thermistor is open-circuited. 2. Check the LGC board (1) Check if the connector J334 is disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) “6” to “0”.

Error code:	C56
Description:	Communication error between main CPU and PFC
Causes:	• If the ADF unit set sensor does not detect the ADF unit.
Remedy:	(1) Check if the conductor pattern around IC57 and IC58 is not short- or open-circuited. (2) Replace the LGC board.

Error code:	C57
Description:	Communications error between LGC-CPU and IPC board
Remedy:	(1) Check if any conductor pattern on the LGC board, mainly around IC23, IC72, IC74 and J125, is short- or open-circuited. (2) Check if the conductor pattern on the IPC board is short- or open-circuited. (3) Replace the IPC board. (4) Replace the LGC board.

Error code:	C58
Description:	Communication error between IPC board and finisher
Causes:	• If the actuator of the Master making unit set switch is not depressed.
Remedy:	Is a specified finisher used? Replace to the specified finisher. Is the harness between the IPC board and finisher control board open-circuited? Replace the harness. Is the conductor pattern on the IPC board is short- or open-circuited? Replace the IPC board. Replace the finisher control board.