Toshiba e-Studio 163

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Число страниц в месяц

50000

Цветность печати

черно-белая

Общие характеристики
Сканер
Копир
Телефон
Факс
Печать фотографий
Тип устройства	МФУ
Размещение	настольный
Тип	лазерный/светодиодный
Технология печати	лазерная
Цветность печати
Число страниц в месяц	50 000
Область применения	средний офис
Макс. формат	A3
Принтер
Прямая печать
Печать без полей
Двусторонняя печать
Время разогрева	24
Макс, разрешение для ч/б печати
По Y	600
По X	2 400
Копир
Макс, количество копий за цикл	999
Время выхода первой копии	8
Значение масштаба
Минимальное	0,25
Максимальное	2
Макс, разрешение (ч/б)
По Y	600
По X	2 400
Скорость цветного копирования
A4	16
Сканер
Слайд-адаптер
Оттенки серого	256
Макс. формат оригинала	A3
Тип сканера	планшетный/протяжный
Макс, размер сканирования
По X	297
По Y	432
Расходные материалы
Ресурс фотобарабана	72 000
Печать на:
Пленках
Этикетках
Глянцевой бумаге
Матовой бумаге
Карточках
Конвертах
Фотобумаге
CD/DVD
Рулоне
Плотность бумаги
Максимальная	163
Минимальная	64
Факс
Цветной
Телефон
Caller ID
Спикерфон
Беспроводная трубка
АОН
Стандарт DECT
Проводная трубка
Автоответчик
Языки управления
PPDS
PostScript 3
PostScript 2
PDF
PostScript
Лотки
Подача бумаги
Стандартная	350
Вывод бумаги
Стандартный	100
Финишер
Сортировка со сдвигом
Брошюровщик
Сортер
Степлер
Интерфейсы
Bluetooth
Wi-Fi
Ethernet (RJ-45)
Инфракрасный порт
FireWire (IEEE 1394)
LPT
RS-232
Устройство для чтения карт памяти
USB
Версия USB	2,0
Поддержка ОС
Windows
Габариты
Ширина	600
Высота	463
Вес	38,1
Глубина	643

Модули

RECYCLE-ASY

MAIN-CHARGER-ASY

REPLACE UNIT

FUSER-2-ASY

GUIDE-ALIGNING-ASY

SUPPLIES

BYPASS-FEEDER-ASY

REAR-FRAME-ASY

STAY-ASY

MAIN-DRIVE-ASY

COVER-1-ASY

CONTROL-PANEL-ASY

FUSER-1-ASY

DEVELOPER-ASY

BYPASS-ASY

COVER-GUIDE-ASY

OPTICAL-DRIVE-ASY

ALIGNING-ASY

FRONT-FRAME-ASY

PM-KIT

CLEANER-ASY

COVER-3-ASY

TRANSPORT-CHARGER-ASY

BASE-FRAME-ASY

COVER-2-ASY

PLATEN-ASY

OPTICAL-FRAME-ASY

DRAWER-ASY

Детали FRONT-FRAME-ASY

Деталь:	BUSH-RGST-F
Парткод:	6LE57207000

Деталь:	SPG-LEVER-TNR-C
Парткод:	6LA88014000

Деталь:	LEVER-TNR-C
Парткод:	6LA88010000

Деталь:	STUD-DRSW-TR
Парткод:	44200855000

Деталь:	EDS-1
Парткод:	F0-00045000

Деталь:	UAMS-05SN-W
Парткод:	F0-00043000

Деталь:	SM-V-21522-3C6
Парткод:	41301175000

Деталь:	BRKT-SW-INT
Парткод:	6LE57911000

Деталь:	S/TPP/BID-3*8-NI
Парткод:	6LA80090000

Деталь:	S/TPS/FPAN-3X14-NC
Парткод:	X0-01615000

Деталь:	S/TPS/FHEXM-3X8-ZU3
Парткод:	X0-02239000

Коды ошибок

C01

C21

C26

C41

C43

C44

C45

C55

C94

C97

CA1

CA2

E01

E02

E03

E09

E12

E13

E14

E21

E40

E41

E44

E71

E72

E73

E86

E87

F14

Деталь:	GEAR-10S23_P2STE62_10H21R
Парткод:	6LE56641000

Деталь:	ASYS-GEAR-5H56L-6-COUPL
Парткод:	6LE56639000

Деталь:	ASYS-GEAR-10S24_P2STE30
Парткод:	6LE56637000

Деталь:	GEAR-10S37_10H17R_10S19-8
Парткод:	6LE56646000

Деталь:	GEAR-5H60L-6-WORM-TNR
Парткод:	6LE56633000

Деталь:	ASYS-BRKT-DRV-FEED-280
Парткод:	6LE56624000

Деталь:	GEAR-10H21-10S20-6-FUS
Парткод:	6LA84140000

Деталь:	GEAR-10S18-6-BYP-TRAY
Парткод:	6LE53448000

Деталь:	ASYS-PAD-PUSHER-GUIDE
Парткод:	6LE53488000

Деталь:	2X10-SS S/TPP/BID-3*8-NI
Парткод:	X0-00980000

Деталь:	ASYS-COV-NOZLE-280
Парткод:	6LE56021000

Деталь:	AUGER-RECY-280
Парткод:	6LE56030000

Деталь:	BUSH-0611-06F-M
Парткод:	6LA81925000

Деталь:	GEAR-8S22-6
Парткод:	6LA81936000

Деталь:	ASYS-GLASS-PLATEN-280-L
Парткод:	6LE60740100

Деталь:	ASYS-GLASS-PLATEN-280-A
Парткод:	6LE60740000

Деталь:	ASYS-GLASS-PLATEN-280-K
Парткод:	6LE60740200

Error code:	C01
Display:	C01-xxx No Ink Replace Ink Cartridge
Description:	Main motor is abnormal
Remedy:	Is the main motor working? NO 1. Check if the connector CN1 of the main motor is disconnected. 2. Check if the connector J313 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circutied. 4. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 5. Replace the main motor. 6. Replace the LGC board. YES Is the LED on the main motor board lit without flickering? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 3. Replace the main motor. 4. Replace the LGC board. YES 1. Check if the PLL lock signal J313-11 output from the LGC board is always level “L”? 2. Check if the voltage supplied to the microcomputer input terminal IC10-7 is always “L”? 3. Replace the LGC board.

Error code:	C21
Description:	Carriage initialization error
Remedy:	1 Does the CIS case move to its home position when the power is turned ON? Yes 1. Check if the CIS home position sensor is installed properly. 2. Check if any of the connectors is disconnected from the CIS home position sensor. 3. Check if the connector CN14 on the MAIN board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the MAIN board are short circuited or open circuited. 6. Replace the CIS home position sensor. 7. Replace the MAIN board. No 2 2 Is there any abnormal sound when the CIS case is moving? Yes 1. Check if the CIS unit drive belt-1 or the CIS unit drive belt-2 is damaged. 2. Check if the belt tension of the CIS unit drive belt-1 or the CIS unit drive belt-2 is loose. 3. Check if the joint of the belt stopper and the CIS unit drive belt-1 is loose. No 3 3 1. Check if the tension of the CIS unit drive belt-1 or the CIS unit drive belt-2 is too tight. 2. Check if any of the connectors of the scan motor is disconnected. 3. Check if the connector CN18 on the MAIN board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open circuited. 5. Check if the conductor patterns on the MAIN board are short circuited or open circuited. 6. Replace the scan motor. 7. Replace the MAIN board

Error code:	C26
Description:	Peak detection error
Remedy:	Does the exposure lamp light? (Perform the output check in the test mode: 03-267) YES 1. Check if the connectors on the CCD and SLG boards are disconnected. 2. Check if the shading correction plate is dirty. 3. Check if the conductor pattern on the CCD board is short- or open-circuited. 4. Check if the conductor pattern on the SLG board is short- or open-circuited. 5. Replace the lens unit. 6. Replace the SLG board. NO 1. Check if the connectors of the exposure lamp and inverter are disconnected. 2. Check the SLG board if the connector pin J9 is disconnected and the harness is short- or opencircuited. 3. Check if the conductor pattern on the SLG board is short- or open-circuited. 4. Replace the SLG board. 5. Replace the inverter. 6. Replace the exposure lamp.

Error code:	C41
Description:	Thermistor or heater abnormal when warming-up is started
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C43
Description:	Thermistor abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C44
Description:	Heater abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C45
Description:	Abnormal side thermistor after the copier has become ready
Causes:	MAIN board Switching regulator
Remedy:	1. Check the side thermistor (1) Check if the connector is disconnected. (2) Check if the side thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the side thermistor is open-circuited. 2. Check the LGC board (1) Check if the connector J334 is disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) “6” to “0”.