Toshiba e-Studio 18

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Число страниц в месяц

77000

Цветность печати

черно-белая

Общие характеристики
Технология печати	лазерная
Тип	лазерный/светодиодный
Сканер
Тип устройства	МФУ
Копир
Число страниц в месяц	77 000
Факс
Размещение	настольный
Телефон
Печать фотографий
Макс. формат	A3
Область применения	средний офис
Цветность печати
Принтер
Пигментные чернила
Прямая печать
Печать без полей
Система непрерывной подачи чернил
Двусторонняя печать
Время разогрева	25
Макс, разрешение для ч/б печати
По Y	600
По X	600
Копир
Время выхода первой копии	7,3
Макс, количество копий за цикл	999
Значение масштаба
Максимальное	4
Минимальное	0,25
Макс, разрешение (ч/б)
По X	600
По Y	600
Скорость ч/б копирования
A4	18
A3	11
Сканер
Макс. формат оригинала	A3
Тип датчика сканера	ПЗС (CCD)
Отправка изображения по e-mail
Слайд-адаптер
Стандарт WIA
Стандарт TWAIN
Оттенки серого	256
Тип сканера	планшетный
Макс, размер сканирования
По X	305
По Y	427
Разрешение сканера
По Х	600
Расходные материалы
Ресурс ч/б картриджа/тонера	22 700
Ресурс фотобарабана	77 000
Ресурс девелопера	77 000
Количество картриджей	1
Печать на:
CD/DVD
Рулоне
Фотобумаге
Конвертах
Матовой бумаге
Глянцевой бумаге
Этикетках
Пленках
Карточках
Плотность бумаги
Минимальная	50
Максимальная	163
Факс
PC Fax
Цветной
Телефон
Беспроводная трубка
Спикерфон
Стандарт DECT
Автоответчик
Caller ID
Проводная трубка
АОН
Языки управления
PCL 6
PCL 5c
PostScript 3
PostScript 2
PostScript
PDF
PPDS
PCL 5e
Лотки
Емкость лотка ручной подачи	100
Подача бумаги
Стандартная	350
Вывод бумаги
Стандартный	250
Финишер
Сортировка со сдвигом
Сортер
Степлер
Брошюровщик
Электронная сортировка
Интерфейсы
Поддержка iOS
AirPrint
USB
LPT
Wi-Fi
FireWire (IEEE 1394)
Ethernet (RJ-45)
Wi-Fi 802.11n
Bluetooth
Устройство для чтения карт памяти
Веб-интерфейс
RS-232
Инфракрасный порт
Память/Процессор
Объем памяти	64
Дополнительная информация
Работа от аккумулятора
Поддержка ОС
Linux
DOS
Mac OS
Windows
Габариты
Ширина	600
Глубина	578
Вес	30
Высота	451

Модули

DEVELOPER-ASY

DRAWER-ASY

FRONT-FRAME-ASY

REAR-FRAME-ASY

GUIDE-ALIGNING-ASY

COVER-ASY

CLEANER-ASY

FUSER-2-ASY

COVER-GUIDE-ASY

TRANSPORT-CHARGER-ASY

BYPASS-FEEDER-ASY

BASE-FRAME-ASY

OPTICAL_ASY

MAIN-DRIVE-ASY

BYPASS-ASY

PLATEN-ASY

MAIN-CHARGER-ASY

FUSER-1-ASY

STAY-ASY

CONTROL-PANEL-ASY

RECYCLE-ASY

ALIGNING-ASY

Детали FUSER-1-ASY

Деталь:	FRAME-FUS-HR-284-N
Парткод:	6LH90400000

Деталь:	PLT-NUT-LMP-284
Парткод:	6LH24660000

Деталь:	PLT-THMS-LMP-280
Парткод:	6LE58575000

Деталь:	THRMST-HTR-284
Парткод:	6LH27402000

Деталь:	THMS-HTR-280
Парткод:	6LE63998000

Деталь:	ASYS-HLD-THMIS-280
Парткод:	6LE58520000

Деталь:	HR-1640-U
Парткод:	6LE19935000

Деталь:	HRNS-LP-ACIN2-280
Парткод:	6LE63314000

Деталь:	GEAR-HR-RLR
Парткод:	6LH24603000

Деталь:	CRR-HT/RLR
Парткод:	6LH24640000

Деталь:	SCRAPER-282
Парткод:	6LE58405000

Деталь:	SPE-SCR-HR-371
Парткод:	6LA84096000

Деталь:	EARTH-FUS-EXIT
Парткод:	6LE58530000

Деталь:	SFT-EXIT-IDLE-280
Парткод:	6LE58600000

Деталь:	ROLL-EXIT-L-282
Парткод:	6LE58555000

Деталь:	ROLLER-EXIT-280
Парткод:	6LH23930000

Деталь:	BUSH-6-GCB
Парткод:	4407734980

Деталь:	HLDR-GEAR-EXIT-280
Парткод:	6LE58401000

Деталь:	GEAR-10S35-5
Парткод:	6LE58540000

Деталь:	GEAR-10S20-8
Парткод:	6LE58570000

Деталь:	SPG-T-EXIT-R-280
Парткод:	6LE58611000

Деталь:	SPG-T-EXIT-F-280
Парткод:	6LE58615000

Деталь:	EARTH-FUS-HEAT
Парткод:	6LE58535000

Деталь:	ASYS-GEAR-HR-EXIT
Парткод:	6LE58490000

Деталь:	GEAR-10H21_10S20-6-FUS
Парткод:	6LH24602000

Деталь:	ROL-IDLE-FUS-284
Парткод:	6LH24605000

Деталь:	BUSH-HR_RLR
Парткод:	6LH24604000

Деталь:	STOP-RING-6-5
Парткод:	4407972860

Деталь:	SCREW-PINION
Парткод:	6LA04456000

Деталь:	ROLL-GUIDE-EXIT-280
Парткод:	6LE58505000

Деталь:	SPG-T-GUIDE-OPEN-2
Парткод:	6LE58886000

Деталь:	SPG-E-FUS-GEAR
Парткод:	6LE58770000

Деталь:	PLT-NUT-FUS-280
Парткод:	6LE58564000

Деталь:	SCREW-M3-FUS-C
Парткод:	6LA36276000

Деталь:	MYLAR-HR-280
Парткод:	6LE58567000

Деталь:	S/BID-M3X8-NI
Парткод:	X0-00434000

Деталь:	USUITA-SPSEMS-4X8-6
Парткод:	6LH55300000

Деталь:	S/PAN/SWWP-M3X8-NI
Парткод:	X0-00077000

Деталь:	S/TPD3/FHEXM-3X6-ZU3
Парткод:	X0-02592000

Деталь:	S/TPP/BID-3*8-NI
Парткод:	6LA80090000

Деталь:	S/FHEXM-M3X10-NI
Парткод:	X0-02232000

Деталь:	RR/E-5-SS
Парткод:	X0-00966000

Деталь:	USUITA-SEMS-3X5-6
Парткод:	6LH55301000

Деталь:	GUIDE-FUS-CURL-282
Парткод:	6LE58625000

Деталь:	SCREW-HLDR-MG
Парткод:	6LA65683000

Деталь:	LVR-EXIT-PAPER
Парткод:	6LJ22901000

Деталь:	ROLL-GUIDE-EXIT
Парткод:	6LA82550000

Деталь:	ROLL-FUS-GUIDE
Парткод:	6LE25931000

Деталь:	LAMP-HTR-C-371-NAD
Парткод:	6LE58630100

Деталь:	LAMP-HTR-C-371-MJD
Парткод:	6LE58630200

Деталь:	LAMP-HTR-S-371-NAD
Парткод:	6LE58631100

Деталь:	LAMP-HTR-S-371-MJD
Парткод:	6LE58631200

Коды ошибок

C01

C26

C41

C43

C44

C45

C97

C9A

CA1

CA2

CE5

CE9

E01

E02

E03

E09

E12

E13

E40

E41

F07

F09

Деталь:	S/TPS/FHEXM/R-3X8-ZU3
Парткод:	X0-02420000

Деталь:	ASYS-GUIDE-MYLAR-RGST-G
Парткод:	6LJ48221000

Деталь:	PRINT_COVER_FRONT_R_B
Парткод:	6LJ28014000

Деталь:	ASYS-SHAFT-RLR-FEED_D
Парткод:	6LH21840000

Деталь:	BUSH-5X8X4R2F-GCB-NU4
Парткод:	6LH23440000

Деталь:	CUSHION-HLDR-BYP-2T11
Парткод:	6LE53502000

Деталь:	GEAR-10S23_P2STE62_10H21R
Парткод:	6LE56641000

Деталь:	ASYS-GEAR-5H56L-6-COUPL-N
Парткод:	6LH23425000

Деталь:	ASYS-GEAR-10S24_P2STE30-N
Парткод:	6LH23426000

Деталь:	GEAR-10S37_10H17R_10S19-8
Парткод:	6LE56646000

Деталь:	ASYS-CASE-DEV-280
Парткод:	6LE55918000

Деталь:	PLATE-SIDE
Парткод:	6LA81632000

Деталь:	MIXER-1-284
Парткод:	6LH23232000

Деталь:	SPACER-MIX
Парткод:	6LA81636000

Деталь:	GEAR-5H60L-6-WORM-TNR
Парткод:	6LE56633000

Деталь:	ASYS-BRKT-DRV-CLTCH-EBW
Парткод:	6LJ48231000

Деталь:	GEAR-10H22L_8S19-6-EBW
Парткод:	6LJ48230000

Деталь:	ASYS-BRKT-DRV-FEED-EBW
Парткод:	6LJ48232000

Деталь:	ASYS-PAD-PUSHER-GUIDE
Парткод:	6LE53488000

Error code:	C01
Display:	C01-xxx No Ink Replace Ink Cartridge
Description:	Main motor is abnormal
Remedy:	Is the main motor working? NO 1. Check if the connector CN1 of the main motor is disconnected. 2. Check if the connector J313 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circutied. 4. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 5. Replace the main motor. 6. Replace the LGC board. YES Is the LED on the main motor board lit without flickering? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the main motor board and LGC board are short- or open-circuited. 3. Replace the main motor. 4. Replace the LGC board. YES 1. Check if the PLL lock signal J313-11 output from the LGC board is always level “L”? 2. Check if the voltage supplied to the microcomputer input terminal IC10-7 is always “L”? 3. Replace the LGC board.

Error code:	C26
Description:	Peak detection error
Remedy:	Does the exposure lamp light? (Perform the output check in the test mode: 03-267) YES 1. Check if the connectors on the CCD and SLG boards are disconnected. 2. Check if the shading correction plate is dirty. 3. Check if the conductor pattern on the CCD board is short- or open-circuited. 4. Check if the conductor pattern on the SLG board is short- or open-circuited. 5. Replace the lens unit. 6. Replace the SLG board. NO 1. Check if the connectors of the exposure lamp and inverter are disconnected. 2. Check the SLG board if the connector pin J9 is disconnected and the harness is short- or opencircuited. 3. Check if the conductor pattern on the SLG board is short- or open-circuited. 4. Replace the SLG board. 5. Replace the inverter. 6. Replace the exposure lamp.

Error code:	C41
Description:	Thermistor or heater abnormal when warming-up is started
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C43
Description:	Thermistor abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Error code:	C44
Description:	Heater abnormal during warming-up after abnormality judgment
Causes:	MAIN board Switching regulator
Remedy:	1. Checking the thermistors (1) Is any thermistor connector disconnected? (2) Are the thermistors (upper/lower, center/rear) in proper contact with the upper and lower heat rollers? (3) Are the harnesses for the thermistors (upper/lower, center/rear) open-circuited? 2. Checking the heater lamps and SSRs (1) Check if the upper or lower heater lamp is open-circuited. (2) Check if the upper or lower heater lamp connector is disconnected. (3) Check if the thermostat is blown out. (4) Check if the upper heat roller or lower heat roller SSR connector is disconnected. (5) Check if the AC harness is open-circuited. (6) Check if SSR or the switching power supply is broken. 3. Checking the LGC board (1) Check the LGC board if the connector J123 is disconnected. (2) Check if the conductor pattern on the LGC board is open- or short-circuited. (3) Replace the LGC board. 4. Clearing the status counter After completing the repair of what caused the error, proceed to do the following: (1) While pressing [0] and [8] simultaneously, turn ON the power. (2) Enter [700] with digital keys, then press the [START] key. (3) Rewrite the status counter to "0", then press the [SET] or [INTERRUPT] key. The status counter is dispalyed as follows: [C41]: "1" or "2" [C42]: "6" [C43]: "4" [C44]: "5" [C46]: "7" [C47]: "8" [C48]: "9" (4) Turn OFF the power and then back it ON again, and make sure that the copier gets ready normally.

Toshiba e-Studio 18

Общие характеристики

Технология печати

Тип

Сканер

Тип устройства

Копир

Число страниц в месяц

Факс

Размещение

Телефон

Печать фотографий

Макс. формат

Область применения

Цветность печати

Принтер

Пигментные чернила

Прямая печать

Печать без полей

Система непрерывной подачи чернил

Двусторонняя печать

Время разогрева

Макс, разрешение для ч/б печати

Копир

Время выхода первой копии

Макс, количество копий за цикл

Значение масштаба

Макс, разрешение (ч/б)

Скорость ч/б копирования

Сканер

Макс. формат оригинала

Тип датчика сканера

Отправка изображения по e-mail

Слайд-адаптер

Стандарт WIA

Стандарт TWAIN

Оттенки серого

Тип сканера

Макс, размер сканирования

Разрешение сканера

Расходные материалы

Ресурс ч/б картриджа/тонера

Ресурс фотобарабана

Ресурс девелопера

Количество картриджей

Печать на:

Плотность бумаги

Факс

PC Fax

Цветной

Телефон

Беспроводная трубка

Спикерфон

Стандарт DECT

Автоответчик

Caller ID

Проводная трубка

АОН

Языки управления

Лотки

Емкость лотка ручной подачи

Подача бумаги

Вывод бумаги

Финишер

Сортировка со сдвигом

Сортер

Степлер

Брошюровщик

Электронная сортировка

Интерфейсы

Поддержка iOS

AirPrint

USB

LPT

Wi-Fi

FireWire (IEEE 1394)

Ethernet (RJ-45)

Wi-Fi 802.11n

Bluetooth

Устройство для чтения карт памяти

Error code:	C45
Description:	Abnormal side thermistor after the copier has become ready
Causes:	MAIN board Switching regulator
Remedy:	1. Check the side thermistor (1) Check if the connector is disconnected. (2) Check if the side thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the side thermistor is open-circuited. 2. Check the LGC board (1) Check if the connector J334 is disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) “6” to “0”.

Error code:	C97
Description:	Vacuum fan motor abnormality
Remedy:	Check the High-voltage transformer. 1. Is the main charger installed securely? 2. Check if the spring of high-voltage supply contact point is deformed. 3. Check if the needle electrode is broken or the main charger grid is deformed. 4. Check if any foreign matters is on the needle electrode or the main charger grid. 5. Is the transfer/separation charger installed securely? 6. Check if the transfer/separation charger wire is broken or unhooked. 7. Check if any foreign matter is on the transfer/separation charger wire.

Error code:	C9A
Description:	Main memory abnormal
Remedy:	Is "Call for service" displayed again even after the copier is turned OFF and then back ON? N: Observe the condition for a while. Y: 1. Check if the conductor pattern between the LGC-CPU (IC32), FROM (IC24), SRAM (IC35) and BC-RAM (IC36) is open- or short-circuited. 2. If this problem recurs frequently, replace the LGC board.

Error code:	CA1
Description:	Polygonal motor rotation abnormal
Remedy:	Is the polygonal motor rotating? N: 1. Check if the polygonal motor connector is disconnected. 2. Check if connector J181 or J188 on the IMC board is disconnected. 3. Check if any harness is open-circuited or any connector pin is disconnected. 4. Check if any conductor pattern on the IMC board is open- or short-circuited. 5. Replace the IMC board. 6. Replace the laser optical unit. Y: Are both 10th and 12th pins of the connector J188 on the IMC board always at the level "L"? N: 1. Check if any conductor pattern on the IMC board is open- or short-circuited . 2. Replace the IMC board. 3. Replace the laser optical unit. Y: 1. Check if any conductor pattern on the IMC board is open- or short-circuited . 2. Replace the IMC board. 3. Replace the laser optical unit.

Error code:	CA2
Description:	H-SYNC abnormal
Remedy:	Is the polygonal motor rotating? N: Refer to "[CA1] Polygonal motor rotation abnormal". Y: Are both 10th and 12th pins of the connector J188 on the IMC board always at the level "L"? N: Refer to "[CA1] Polygonal motor rotation abnormal". Y: Is the harness between the RLY and IMC boards open-circuited? Are the connector J185 on the IMC board or the connector J201 on the RLY board disconnected? Y: Replace the harness. Reconnect the connectors. N: 1. Replace the IMC board. 2. Replace the laser optical unit.

Error code:	CE5
Description:	Temperature/humidity sensor upper-limit abnormal
Remedy:	Is the harness between the LGC board and the temperature/humidity sensor disconnected ? Is the connector J108 on the LGC board or the connector of the temperature/humidity sensor disconnected ? Y: Reconnect the connector. Replace the harness. N: 1. Replace the temperature/humidity sensor. 2. Replace the LGC board.

Error code:	CE9
Description:	Drum thermistor abnormal (K)
Remedy:	Is the harness between the LGC board and the drawer connector for EPU disconnected ? Is the harness inside of the EPU and the harness of the drum thermistor Y or K disconnected ? Is the connector J120 on the LGC board, or the connector of the drum thermistor Y or K disconnected ? Y: Reconnect the connector. Replace the harness. N: 1. Replace the drum thermistor Y or K. 2. Replace the LGC board.

Error code:	E01
Description:	Paper leading edge not reaching the exit sensor
Remedy:	Is the fuser motor rotating? Y: Is the harness between the LGC board and the exit sensor open-circuited? Is the connector of the paper exit sensor or the connector J123 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the exit sensor. 2. Replace the LGC board. N: Is the harness between the LGC board and the paper exit sensor open-circuited? Is the fuser motor connector or the connector J122 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the fuser motor. 2. Replace the LGC board. Where was the paper stopped? Near the exit sensor (paper not damaged) Are the registration seRemove the paper after the fuser unit cools down.nsor and paper exit sensor functioning properly? (Does the actuator return normally?) Y: 1. In the tRemove the paper after the fuser unit cools down.est mode (03) check if each sensor is functioning. 2. Reconnect each sensor connector. N: Repair the actuator if it has come off. Before reaching the fuser unit Did the paper stop, curling upward excessively? Y: Replace the paper in the cassette. From the transfer belt surface to the exit sensor Do the size of paper and the size set match? N: Make the sizes match. Y: Is the transfer belt moving? Is the black drum motor or the transfer belt motor stopped? Or is any abnormal noise heard from one of them due to loss of synchronism? Y: 1. Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. 2. Check the motor connector, and the connector J130 on the LGC board. 3. Replace the motor. 4. Replace the LGC board. No paper found Is the paper attached to the fuser belt? Remove the paper after the fuser unit cools down.

Error code:	E02
Display:	E02-xxx !!Maintenance!! Call Service
Description:	Paper trailing edge not passing the exit sensor
Remedy:	Is the fuser motor rotating? Y: Is the harness between the LGC board and the exit sensor open-circuited? Is the connector of the paper exit sensor or the connector J123 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the exit sensor. 2. Replace the LGC board. N: Is the harness between the LGC board and the paper exit sensor open-circuited? Is the fuser motor connector or the connector J122 on the LGC board disconnected? Y: Reconnect the connector. Replace the harness. N: 1. Replace the fuser motor. 2. Replace the LGC board. Where was the paper stopped? Near the exit sensor (paper not damaged) Are the registration seRemove the paper after the fuser unit cools down.nsor and paper exit sensor functioning properly? (Does the actuator return normally?) Y: 1. In the tRemove the paper after the fuser unit cools down.est mode (03) check if each sensor is functioning. 2. Reconnect each sensor connector. N: Repair the actuator if it has come off. Before reaching the fuser unit Did the paper stop, curling upward excessively? Y: Replace the paper in the cassette. From the transfer belt surface to the exit sensor Do the size of paper and the size set match? N: Make the sizes match. Y: Is the transfer belt moving? Is the black drum motor or the transfer belt motor stopped? Or is any abnormal noise heard from one of them due to loss of synchronism? Y: 1. Reduce the mechanical load by adjusting the drive system. Remove any foreign matter. 2. Check the motor connector, and the connector J130 on the LGC board. 3. Replace the motor. 4. Replace the LGC board. No paper found Is the paper attached to the fuser belt? Remove the paper after the fuser unit cools down.

Error code:	E03
Description:	Paper remaining inside the copier at power ON
Remedy:	Is any paper remaining inside the copier? Y: Remove the paper. N: Refer to [E01], [E02] and [E11] to [E26].